550-020Manual.qxd 7/6/04 3:32 PM Page 1
Fast Media
Home Network
Systems
Installation
Guide
550-020
Fast Media
Telephone Hub Module
1
7
2
8
6 / ˝ (W) x 2 / ˝ (H) x 1˝ (D)
Manufactured by:
Steren Electronics International, LLC
8675 Miralani Drive, San Diego, CA 92126
1-800-266-3333
R
Download from Www.Somanuals.com. All Manuals Search And Download.
550-020Manual.qxd 7/6/04 3:32 PM Page 3
FastHome™
550-020 Telephone Hub Module Installation Guide
Pre-Installation Instructions
1. After the enclosure has been mounted, determine which modules will be inserted. On a
sheet of paper, diagram the location where each module will be placed. An expansion
module should be placed close to the module with which it interfaces.
Installation
2. On the diagram, identify the origin and destination of each cable. Make sure the module
serving each device is safely within a 100ft/30m distance.
Installation Instructions
1. Identify the enclosure location on which the module will be mounted.
2. Mount the module by inserting the nylon pins into the holes in back of the enclosure and
pressing the pins in. Make sure that the pins are firmly seated and the module is secure.
Wiring Instructions
Note: Module wiring should only be performed by a experienced, licensed electrician. Make
sure all power has been shut off to the equipment and there is no live circuit. Route all cables
through the knock-out holes and bundle with tie wraps or cable straps to ensure safe and
long-lasting connections.
1. Route Category 5 phone cables from the network interface device at the phone company’s
demarcation point to the module.
2. Using a wire stripper, strip off about 2˝ of the cable to expose the wires. Separate the four
wire pairs.
3. Using a standard 110 punchdown tool, terminate the tip and ring wires at the “from telcom”
side of the telephone hub. Match each wire pair with the color codes on the IDC block
(white/blue: blue pair in line one; white/orange: orange pair in line two; white/green: green
pair in line three; white/brown: brown pair in line four).
Sample configuration for telephone,
audio/video, security and Ethernet.
4. Perform the stripping and punchdown function for wires at the “output” side of the telephone
hub, for 1-6 locations in the home.
5. Tag each cable in the module with its point of destination.
6. Route the cables from the hub to the phone/fax/modem locations in the home and termi-
nate accordingly.
Security System:
This FastHome™ module offers a connection to the security system that
can override any phone in use and alert the security service provider of an
emergency. To enable this function, connect the security system cable to
the module’s RJ-31X jack located below the expansion port. (Refer to the
manual from the security system manufacturer for specific instructions and
safety information.)
For More Information
about FastHome and
™
Fast Media Home Network
Systems, contact:
Steren Electronics International, LLC
8675 Miralani Drive
San Diego, CA 92126
1-800-266-3333
Copyright © 2004
Steren Electronics International, LLC
Printed in China
R
Fast Media Home Network Systems Revised 06/04
—3—
Download from Www.Somanuals.com. All Manuals Search And Download.
550-020Manual.qxd 7/6/04 3:32 PM Page 4
Fast Media
Home Network
Systems
For your future construction needs, consider the
entire series of FastHome™ Enclosures and Modules.
™
FastHome Enclosures
From a centralized location,
Fast Media Home Network
Systems enclosures fully inte-
grate, manage and distribute
broadband and multimedia serv-
ices on a flexible, customizable
and upgradeable platform.
Constructed of 18-gauge cold
rolled steel for strength and
protection against interference,
FastHome™ enclosures mount
on a wall (surface mount) or
between 16˝ center wall studs
(flush mount).
550-100
550-105
Small Surface Mount Enclosure
Large Surface Mount Enclosure
5
9
5
7˝(W) x 11˝(H) x 3 /16˝(D)
14 /16˝(W) x 19˝(H) x 4 /16˝(D)
™
FastHome Modules
™
High-quality FastHome modules
by Steren provide secure, reliable
connections for voice, video,
data and audio applications.
Each module is housed in a
sturdy 18-gauge cold rolled steel
construction for excellent RFI
shielding. The system is expand-
able by adding multiple modules.
550-200
550-205
550-210
Small Flush Mount Enclosure
Medium Flush Mount Enclosure
Large Flush Mount Enclosure
1
3
1
3
3
1
2
14 /8˝(W) x 19˝(H) x 3 /2˝(D)
14 /8˝(W) x 32˝(H) x 3 / ˝(D)
8
2
14 / ˝(W) x 44˝(H) x 3 / ˝(D)
550-010
550-020
550-030
550-040
Fast Media Telephone/TV Hub Module
Fast Media Telephone Hub Module
Fast Media Data Hub Module
Fast Media TV
1
3
1
7
1
7
6 /2˝(W) x 4 /4˝(H) x 1˝(D)
6 /2˝(W) x 2 /8˝(H) x 1˝(D)
6 /2˝(W) x 2 /8˝(H) x 1˝(D)
Combiner/Splitter Module
1
7
6 /2˝(W) x 2 /8˝(H) x 1˝(D)
550-050
550-060
550-070
550-080
Fast Media Audio Splitter Module
Fast Media Ethernet Switch Module
Fast Media Power Module
Fast Media RF Modulator Module
1
7
1
3
1
5
1
3
6 /2˝(W) x 2 /8˝(H) x 1˝(D)
6 /2˝(W) x 2 /4˝(H) x 1˝(D)
6 /2˝(W) x 2 /8˝(H) x 1˝(D)
6 /2˝(W) x 3˝(H) x 2 /8˝(D)
Manufactured by:
Steren Electronics International, LLC
8675 Miralani Drive, San Diego, CA 92126
1-800-266-3333
R
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|