Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAMES & FUNCTIONS
10) PITCH SLIDER
Use this to change the speed of the platter
when the PITCH button is lit.
11) HEADSHELL LOCKING NUT
Attach the headshell by inserting into the front
end of the tone arm, then turn the locking nut
clockwise with the head shell firmly held
horizontally.
12) TONE ARM
This is a fully manual tone arm. To start
playback, gently place the stylus on the record
using the headshell finger support. Do not drop
the stylus onto the record as it may cause
damage to the diamond tip and to the record.
13) PITCH ON/OFF
The ON setting will allow use of the pitch adjust.
When set of OFF, the pitch control will be
locked at 0%.
14) TONE ARM BASE
The tone arm base includes the height
adjustment, tone arm rest. See “tone arm and
cartridge settings” for proper adjustments. Note:
No Anti-Skate is needed on straight tonearms.
1) STROBE DOTS
The dots around the edge of the platter are
used in conjunction with the light located inside
the motor ON/OFF switch. While the platter is
in rotation, the dots help to indicate the speed
of rotation. The speed is lower than the
displayed speed (33,45,78) when the dots are
flowing to the right. It is higher than the
displayed speed (33,45,78) when the dots are
flowing to the left. When the strobe is stopped,
the platter is rotating at the displayed speed.
4) PLATTER REVOLUTION SPEEDS (rpm)
33 rpm – Press 33
15) COUNTERWEIGHT
Use this to balance the tone arm and to adjust
the stylus pressure.
45 rpm – Press 45
78 rpm – Press 33 and 45 buttons
simultaneously. To return to 33 or 45-rpm play
mode, just press the desired button.
16) HEADSHELL HOLDER
This is used to place extra headshell during a
performance for quick access.
5) HEASDHELL
When installing a phonograph cartridge, refer
to the installation instructions supplied by the
cartridge manufacture.
17) OUTPUT
This is the standard analog output (RCA jacks)
which can be connected to a phono input on
any DJ mixer.
2) MOTOR ON/OFF SWITCH
As opposed to analog turntables, this is not the
power switch. This switch only turns on or off
the motor. Rotate clockwise to turn on the
motor. The platter will not start spinning until
the start/stop button has been pressed. Rotate
counter-clockwise during playback (off position)
for a slow winding down effect.
6) TAGRET LIGHT
Press the button to light up the stylus. To
retract the light, press down on the light itself.
18) GND
Ground wire connection post
7) REVERSE
This button is used to reverse the direction of
the platter rotation.
19) POWER SETICH
This switch turns the power on or off, including
the motor and audio signal.
3) START/STOP
8) PITCH SELECT
Press this button to start or stop the platter.
Press the button to switch between
+/-8%,+/-16%, or +/-25% pitch range.
20) POWER CORD CONNECTOR
Used to connect the included power cord.
9) PITCH BEND
The pitch will increase/decrease by up to 6%
while the pitch bend minus button is pressed.
Download from Www.Somanuals.com. All Manuals Search And Download.
SCRATCH PROTECTION
SPECIFICATIONS
The STR8-90 includes a
TURNTABLE SECTION
pair of rubber protectors.
These were designed to
protect the turntable’s
rounded aluminum edges
from the mixer while
scratching. When the
Starting Torque:
Motor:
Platter:
Pitch:
Brake:
More than 2.2kgf.com
16pole, 3phase, brushless DC motor
330mm dia. Aluminum diecast
+/-8%,+/-16%,+/-25%
Electronic brake
turntables are placed
sideways, the round edges
of the turntable may come
TONE ARM SECTION
Tone arm type
Static balanced straight
tonearm with Cardan suspension
191mm
0-4g
6-10g
in contact with the mixer’s
rack ears causing damage
to the turntable body. Placing the rubber protectors on the mixer rack
ears (see picture) will prevent the turntable from getting scratched.
Effective Arm Length
Tracking Force Adjust Range
Applicable Cartridge Weight
Frequency Response
Channel Separation
Channel Balance
20 - 20 kHz
More than 15 dB
Within 2.5dB at 1 KHz
Less than 0.20% WRMS
(JIS WTD) with 33 1/3rpm
More than 50dB (DIN-B)
1.5-2g
WARRANTY
Wow & Flutter:
This unit has been designed and manufactured using quality components.
Therefore, it is warranted to be free from defects in materials (limited as
specified below), and workmanship for a period of twelve (12) months
from the original purchase date. During this period, all service and parts
necessary to repair a defect will be free of charge. This limited warranty
applies to mechanical parts which are subject to wear and tear as
specified: Faders, specified durability: 50,000 cycles; 10,000 cycles;
Switches, specified durability: 10,000 cycles. Consequently, the parts
listed above are warranted to be free from defects in materials and
workmanship for a period of thirty days (30) days from the original
purchase date.
S/N ratio:
Needle Pressure range
GENERAL SPECIFICATIONS
Dimensions:
450(W) x 370 (D) x 140 (H)mm
17-3/4" x 14-5/8" x 5.5" (WxDxH)
9.9Kg (21.8 lbs.)
AC 100V, 50/60Hz
12W
Weight:
Power supply:
Power consumption:
Note: For the warranty to be valid, please complete the online
Stanton Magnetics, INC. 3000 SW 42nd Street x Hollywood, FL 33312
Tel: (954) 689-8833 Fax: (954) 689-8460
Email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|