CS05/CS06
HYDRAULIC
CHAIN SAW
USER MANUAL
Safety, Operation and Maintenance
© 2014 Stanley Black & Decker, Inc.
New Britain, CT 06053
U.S.A.
66864 7/2014 Ver. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFETY SYMBOLS ..................................................................................................................................................4
SAFETY PRECAUTIONS..........................................................................................................................................5
ELECTRICAL PRECAUTIONS .................................................................................................................................7
TOOL STICKERS & TAGS........................................................................................................................................9
HOSE TYPES..........................................................................................................................................................10
HOSE RECOMMENDATIONS ................................................................................................................................ 11
FIGURE 1. TYPICAL HOSE CONNECTIONS..................................................................................................... 11
HTMA REQUIREMENTS.........................................................................................................................................12
OPERATION............................................................................................................................................................13
FIGURE 2. FELLING A TREE ..............................................................................................................................14
FIGURE 3. CROSSCUTTING LOGS WITH PRESSURE ON TOP .....................................................................15
FIGURE 4. CROSSCUTTING LOGS LARGER THAN BAR LENGTH WITH PRESSURE ON TOP...................15
FIGURE 5. CROSSCUTTING LOGS/LIMBS WITH PRESSURE ON BOTTOM. ................................................16
FIGURE 6. CROSSCUTTING THICK LOGS WITH PRESSURE ON BOTTOM .................................................16
TOOL PROTECTION & CARE................................................................................................................................18
TROUBLESHOOTING ............................................................................................................................................19
SPECIFICATIONS...................................................................................................................................................20
ACCESSORIES.......................................................................................................................................................20
SERVICE TOOLS....................................................................................................................................................20
CS05/CS06 PARTS ILLUSTRATION ......................................................................................................................21
CS05/CS06 PARTS LIST ........................................................................................................................................22
UNDERWATER TOOLS DEPTH GUIDELINE.........................................................................................................24
IMPORTANT
To fill out a Product Warranty Recording form, and for information on your warranty,
visit Stanleyhydraulics.com and select the Company tab, Warranty.
(NOTE: The warranty recording form must be submitted to validate the warranty).
SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hy-
draulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, be performed
by an authorized and certified dealer. Please read the following warning.
WARNING
SERIOUS INJURY OR DEATH COULD RESULT FROM
THE IMPROPER REPAIR OR SERVICE OF THIS TOOL.
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE
DONE BY AN AUTHORIZED AND CERTIFIED DEALER.
For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back
of this manual and ask for a Customer Service Representative.
CS05/CS06 User Manual ◄ 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SYMBOLS
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair ac-
tions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
This safety alert and signal word indicate an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
DANGER
WARNING
CAUTION
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This safety alert and signal word indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
This signal word indicates a potentially hazardous situation which, if not avoid-
ed, may result in property damage.
CAUTION
NOTICE
This signal word indicates a situation which, if not avoided, will result in damage
to the equipment.
This signal word indicates a situation which, if not avoided, may result in dam-
age to the equipment.
IMPORTANT
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONS
Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte-
nance personnel.
4 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
Tool operators and maintenance personnel must always
•
Do not operate a damaged, improperly adjusted, or
comply with the safety precautions given in this manual
and on the stickers and tags attached to the tool and
hose.
incompletely assembled chain saw. Be sure that the
chain stops moving when the control trigger is re-
leased.
These safety precautions are given for your safety. Re-
view them carefully before operating the tool and before
performing general maintenance or repairs.
•
•
•
Never wear loose clothing that can get entangled in
the working parts of the tool.
Keep all parts of your body away from the chain saw
and maintain proper footing and balance at all times.
Supervising personnel should develop additional pre-
cautions relating to the specific work area and local
safety regulations. If so, place the added precautions in
the space provided in this manual.
Warning: Use of this tool on certain materials during
demolition could generate dust potentially contain-
ing a variety of hazardous substances such as as-
bestos, silica or lead. Inhalation of dust containing
these or other hazardous substances could result
in serious injury, cancer or death. Protect yourself
and those around you. Research and understand
the materials you are cutting. Follow correct safety
procedures and comply with all applicable national,
state or provisional health and safety regulations
relating to them, including, if appropriate arranging
for the safe disposal of the materials by a qualified
person.
The model CS05/CS06 Hydraulic Chain Saw will provide
safe and dependable service if operated in accordance
with the instructions given in this manual. Read and un-
derstand this manual and any stickers and tags attached
to the tool and hose before operation. Failure to do so
could result in personal injury or equipment damage.
•
Do not rely exclusively upon the safety devices built
into the saw. As a chain saw user, several steps
must be taken to keep your cutting jobs free from
accidents or injury.
•
•
The operator must start in a work area without by-
standers. Flying debris can cause serious injury.
Do not operate the tool unless thoroughly trained
or under the supervision of an instructor. Establish
a training program for all operators to ensure safe
operation.
–
With basic understanding of kickback, you can
reduce or eliminate the element of surprise.
Sudden surprise contributes to accidents.
–
To avoid personal injury or equipment damage,
all tool repair, maintenance and service must
only be performed by authorized and properly
trained personnel.
•
Always wear safety equipment such as goggles, ear
and head protection, and safety shoes at all times
when operating the tool. Use gloves and aprons
when necessary.
–
–
Keep a good firm grip on the saw with both
hands, the right hand on the rear handle and
the left hand on the front handle when operating
the saw. Use a firm grip with thumbs and fingers
encircling the chain saw handles. A firm grip will
help reduce kickback and maintain control of
the saw. Do not let go.
•
•
The operator must be familiar with all prohibited
work areas such as excessive slopes and danger-
ous terrain conditions.
Do not inspect, clean or replace any part(s) if the
hydraulic power source is connected. Do not inspect
or clean the tool while the hydraulic power source is
connected. Accidental engagement of the tool can
cause serious injury.
Make sure the area in which you are cutting is
free of obstructions. Never allow the nose of the
guide bar to contact the log, branch or any ob-
struction that can be accidently hit while operat-
ing the saw.
•
•
Always connect hoses to the tool hose couplers be-
fore energizing the hydraulic power source. Be sure
all hose connections are tight and are in good condi-
tion.
–
–
–
–
Never start the tool while it is lying on the ground.
Cut at rated operating speeds (gpm).
Do not operate the tool at oil temperatures above
140 °F/60 °C. Operation at higher temperatures can
cause higher than normal temperatures at the tool
which can result in operator discomfort.
Do not overreach or cut above shoulder height.
Follow the manufacturer’s sharpening and
CS05/CS06 User Manual ◄ 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
–
–
maintenance instructions for the saw chain.
•
When cutting a limb that is under tension, be alert
for springback so that you will not be struck when
the tension on the limb is released.
Only use replacement bars and chains specified
by Stanley Hydraulic Tools. Chains must meet
the requirements of ANSI B175.1 for low kick-
back performance.
•
•
Keep the handles dry, clean and free of oil.
Do not operate a chain saw while in a tree unless
you have been specially trained to do so.
•
•
Always be well rested and mentally alert before op-
erating the chain saw.
•
When using tools near energized transmission lines,
be sure to use only hoses labeled and certified non-
conductive.
Do not allow other persons to be near the chain saw
when starting or cutting with the chain saw. Keep
bystanders and animals out of the work area.
•
•
•
•
Turn off the power unit or move the hydraulic control
valve to neutral before setting the saw down.
•
Do not starting cutting until you have a clear work
area, secure footing and a planned escape path
from a falling tree.
Use a guide bar scabbard when transporting the
saw.
•
•
Carry the saw with the unit de-energized and the bar
and chain to the rear of your body.
Know the location of buried or covered electrical
services before starting work.
Use extreme caution when cutting small size brush
and saplings. Twigs may catch the saw chain and
be whipped toward the operator or pull the operator
off balance.
To avoid personal injury or equipment damage, all
tool repair, maintenance and service must only be
performed by authorized and properly trained per-
sonnel.
6 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL PRECAUTIONS
The following guidelines must be followed to prevent 1. Branches or limbs being removed cannot first be
accidental contact with overhead electrical conductors
and/or communication wires and cables. (ref. ANSI
Z133.1-2000)
cut (with a pole pruner/pole saw) to sufficiently
clear electrical conductors, so as to avoid con-
tact.
Working in Proximity to Electrical Hazards:
2. Roping is required to remove branches or limbs
from such electrical conductors. This does not
apply to individuals working on behalf of, or em-
ployed by, electrical system owners/operators
engaged in line-clearing operations incidental to
their normal occupation.
An inspection shall be made by a qualified arborist to
determine whether an electrical hazard exists before
climbing, or otherwise entering, or performing work in
or on a tree.
Only qualified line-clearance arborists or qualified line-
clearance arborist trainees shall be assigned to work
where an electrical hazard exists. Qualified line-clear-
ance arborist trainees shall be under the direct supervi-
sion of qualified line-clearance arborist.
Qualified line-clearance arborists and line-clearance
arborist trainees shall maintain minimum approach
distances from energized electrical conductors in ac-
cordance with Table 1.
A second qualified line-clearance arborists or line-clear-
ance arborist trainees shall be within vision or voice
communication during line-clearing operations aloft
when line-clearance arborists or line-clearance arborist
trainees must approach closer than 10 feet (3.05 me-
ters) to any energized electrical conductor in excess of
750 volts (primary conductor) or when:
All other arborists shall maintain a minimum ap-
proach distance from energized electrical conductors
in accordance with Table 2.
Branches hanging on an energized electrical con-
ductor shall be removed using non-conductive equip-
ment.
Table 1 – Minimum approach distances from energized conductors for qualified line-clearance arborists and
qualified line- clearance arborist trainees.
Includes 1910.269
elevation factor,
Includes 1910.269
elevation factor,
5001 – 10,000 ft1
Includes 1910.269 elevation
sea level to 5000 ft1
factor, 10,000 – 14,000 ft1
Nominal Voltage
(kV phase-to-phase)
ft–in
m
ft–in
m
ft–in
m
0.05 to 1.0
1.1 to 15.0
Avoid contact
Avoid contact
Avoid contact
2–04
2–09
3–00
3–09
4–06
5–02
6–00
7–11
0.71
0.84
0.92
1.14
1.37
1.58
1.83
2.41
4.02
5.80
8.34
2–08
3–02
3–05
4–03
5–02
5–11
0.81
0.97
1.04
1.30
1.58
1.80
2.08
2.75
4.58
6.63
9.53
2–10
3–05
3–09
4–07
5–07
6–05
7–05
9–09
16–03
23–06
33–10
0.86
1.04
1.14
1.40
1.70
1.96
2.26
2.97
4.96
7.17
10.32
15.1 to 36.0
36.1 to 46.0
46.1 to 72.5
72.6 to 121.0
138.0 to 145.0
161.0 to 169.0
230.0 to 242.0
345.0 to 362.0
500.0 to 550.0
765.0 to 800.0
6–10
9–00
15–00
21–09
31–03
13–02
19–00
27–04
1 Exceeds phase-to-ground; elevation factor per 29 CFR 1910.269.
CS05/CS06 User Manual ◄ 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL PRECAUTIONS
Table 2 – Minimum approach distances to energized conductors for persons
other than qualified line-clearance arborists and qualified line-clearance ar-
borist trainees.
Distance
Nominal Voltage
kV phase-to-phase1
ft-in
m
0.0 to 1.0
1.1 to 15.0
10–00
10–00
10–00
10–00
10–09
12–04
13–02
14–00
16–05
20–05
26–08
35–00
3.05
3.05
3.05
3.05
3.28
3.76
4.00
4.24
4.97
6.17
8.05
10.55
15.1 to 36.0
36.1 to 50.0
50.1 to 72.5
72.6 to 121.0
138.0 to 145.0
161.0 to 169.0
230.0 to 242.0
345.0 to 362.0
500.0 to 550.0
785.0 to 800.0
1 Exceeds phase-to-ground.
The tie-in position should be above the work area and
located in such a way that a slip would swing the arborist
away from any energized electrical conductors or other
identified hazard.
STORM WORK AND EMERGENCY
CONDITIONS-LINE CLEARANCE
Line clearance shall not be performed during adverse
weather conditions such as thunderstorms, high winds
and snow and ice storms.
While climbing, the arborist should climb on the side of
the tree that is away from energized electrical conduc-
tors as required in Tables 1 and 2.
Qualified line-clearance arborists and qualified line-
clearance arborists trainees performing line clearance
in the aftermath of a storm or under similar conditions
shall be trained in the special hazards associated with
this type of work.
Footwear, including lineman’s overshoes, having electri-
cal-resistant soles, shall not be considered as providing
any measure of safety from electrical hazards.
Rubber gloves, with or without leather or other protec-
tive covering, shall not be considered as providing any
measure of safety from electrical hazards.
Line-clearance operations shall be suspended when
storm work or emergency conditions develop involving
energized electrical conductors. Electrical system own-
ers/operators shall be notified immediately.
Ladders, platforms and aerial devices, including insulat-
ed aerial devices, shall be subject to minimum approach
distances in Table 1 and 2.
Aerial devices and attached equipment (such as chip-
pers) contacting energized electrical conductors shall be
considered energized. Contact shall be avoided, except
where emergency rescue procedures are being carried
out. Emergency rescue should be performed in accor-
dance with 4.3.
8 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL STICKERS & TAGS
DANGER
Lwa
Failure to use hydraulic hose labeled and certified
as non-conductive when using hydraulic tools on
D
or near electric lines may result in death or
serious injury.
30 LPM @ 138 B AR
EHTMA CATEGORY
107
For proper and safe operation read owners manual
and mwke sure that you have been properly
trained in correct procedures required for work
on or around electric lines.
28323
CE Decal
(CE Models Only)
11207
Circuit Type D Decal
(CE Models Only)
28409
17784
ELECTROCUTION
HAZARD
101 Sound Level
Decal
(CE Models Only)
12412
Electrical Warning Decal
Composite Dec
(CE Models On
4-6 GPM / 15-22 LPM
DO NOT EXCEED 2000 PSI / 140 BAR
DO NOT EXCEED SPECIFIED FLOW OR PRESSURE
USE CLOSED-CENTER TOOL ON CLOSED-CENTER
SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER
SYSTEM. CORRECTLY CONNECT HOSES TO TOOL “IN”
AND “OUT” PORTS. IMPROPER HANDLING, USE OR OTHER
MAINTENANCE OF TOOL COULD RESULT IN A LEAK, BURST
OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST
CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
03782
GPM Decal – CS05 Model
03786
13907
Kickback Warning Decal
GPM Decal – CS06 Model (Not Shown)
THIS CHAIN SAW IS
EQUIPPED WITH AN
AUTOMATIC CHAIN
OILER.
SEE YOUR PARTS &
SERVICE BOOK FOR
PROPER ADJUSTING
PROCEDURES
D A N G E R
D A N G E R
Stanley Hydraulic Tools
3810 SENaef Road
Milwaukie, OR97062
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTI-
FIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
Model
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLYTESTED FOR ELECTRIC CURRENT
LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART-
MENT INSTRUCTIONS.
07636
Name Tag
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION
INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL
INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEMAND/OR SEVERE PERSONAL INJURY.
A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
04746
Auto Oiler Decal
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
B. DO NOT EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
NOTE
THE INFORMATION LISTED ON THE
STICKERS SHOWN, MUST BE LEGIBLE AT ALL
TIMES.
I M P O R T A N T
I M P O R T A N T
REPLACE DECALS IF THEY BECOME WORN
OR DAMAGED. REPLACEMENTS ARE
AVAILABLE FROM YOUR LOCAL STANLEY
DISTRIBUTOR.
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
The safety tag (P/N 15875) at right is attached to
the tool when shipped from the factory. Read and
understand the safety instructions listed on this tag
before removal. We suggest you retain this tag and
attach it to the tool when not in use.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
SEE OTHER SIDE
SAFETY TAG P/N 15875 (Shown smaller then actual size)
CS05/CS06 User Manual ◄ 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE TYPES
The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy-
draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with
Stanley Hydraulic Tools. They are:
Certified non-conductive — constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid
reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non-
conductive is the only hose authorized for use near electrical conductors.
Wire-braided (conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce-
ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near
electrical conductors.
Fabric-braided (not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in-
ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This
hose is not certified non-conductive and must never be used near electrical conductors.
HOSE SAFETY TAGS
To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic
Tools. DO NOT REMOVE THESE TAGS.
If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be
obtained from your Stanley Distributor.
THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE
D A N G E R
D A N G E R
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.
KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT
CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION
AND SEVERE PERSONAL INJURY.
FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-
ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND
ELECTRIC LINES.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR
CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT
USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-
TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND
TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH
SAFETY DEPARTMENT INSTRUCTIONS.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-
AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE
IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SEE OTHER SIDE
SEE OTHER SIDE
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE
SIDE 1
SIDE 2
(Shown smaller than actual size)
THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.
D A N G E R
D A N G E R
1. DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS
NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKSABRASIONS, BULGES, OR DAMAGE TO
COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-
TRIC LINES.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SEE OTHER SIDE
3. DO NOT EXCEED HOSE WORKING PRESSURE ORABUSE HOSE. IMPROPER USE OR HAN-
DLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSEAS FAR
AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE.
CONTACTATTHE BURST CAN CAUSE BODILY INJECTIONAND SEVERE PERSONALINJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT
WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO
PULL OR LIFT TOOLS, POWER UNITS, ETC.
SEE OTHER SIDE
SIDE 1
SIDE 2
(Shown smaller than actual size)
10 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE RECOMMENDATIONS
CS05/CS06 User Manual ◄ 11
Download from Www.Somanuals.com. All Manuals Search And Download.
HTMA / EHTMA REQUIREMENTS
HTMA / EHTMA REQUIREMENTS
HTMA
TOOL TYPE
HYDRAULIC SYSTEM REQUIREMENTS
TYPE I
TYPE II
TYPE RR
9-10.5 gpm
(34-40 lpm)
1500 psi
TYPE III
11-13 gpm
(42-49 lpm)
1500 psi
4-6 gpm
7-9 gpm
Flow Range
(15-23 lpm)
1500 psi
(103 bar)
(26-34 lpm)
1500 psi
(103 bar)
Nominal Operating Pressure
(at the power supply outlet)
(103 bar)
(103 bar)
2100-2250 psi
(145-155 bar)
2100-2250 psi
(145-155 bar)
2200-2300 psi
(152-159 bar)
2100-2250 psi
(145-155 bar)
System relief valve setting
(at the power supply outlet)
250 psi
(17 bar)
250 psi
(17 bar)
250 psi
(17 bar)
250 psi
(17 bar)
Maximum back pressure
(at tool end of the return hose)
400 ssu*
400 ssu*
400 ssu*
400 ssu*
Measured at a max. fluid viscosity of:
(82 centistokes) (82 centistokes) (82 centistokes) (82 centistokes)
(at min. operating temperature)
Temperature: Sufficient heat rejection
capacity to limit max. fluid temperature to:
(at max. expected ambient temperature)
140° F
(60° C)
140° F
(60° C)
140° F
(60° C)
140° F
(60° C)
Min. cooling capacity at a temperature
3 hp
5 hp
6 hp
7 hp
difference of between ambient and fluid
temps
(2.24 kW)
40° F
(3.73 kW)
40° F
(5.22 kW)
40° F
(4.47 kW)
40° F
NOTE:
(22° C)
(22° C)
(22° C)
(22° C)
Do not operate the tool at oil temperatures above 140° F (60° C). Operation at higher temperatures can cause operator
discomfort at the tool.
Filter
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
25 microns
30 gpm
(114 lpm)
Min. full-flow filtration
Sized for flow of at least:
(For cold temp. startup and max.
dirt-holding capacity)
Hydraulic fluid Petroleum based
(premium grade, anti-wear, non-conductive)
Viscosity (at min. and max. operating temps)
100-400 ssu*
100-400 ssu*
(20-82 centistokes)
100-400 ssu*
100-400 ssu*
NOTE:
When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the
most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the requirements
over a wide range of operating temperatures.
*SSU = Saybolt Seconds Universal
CLASSIFICATION
EHTMA
HYDRAULIC SYSTEM
REQUIREMENTS
C
B
D
Flow Range
3.5-4.3 gpm
(13.5-16.5 lpm) (18-22 lpm)
1870 psi
(129 bar)
4.7-5.8 gpm
7.1-8.7 gpm
(27-33 lpm)
1500 psi
9.5-11.6 gpm
(36-44 lpm)
1500 psi
11.8-14.5 gpm
(45-55 lpm)
1500 psi
Nominal Operating Pressure
(at the power supply outlet)
1500 psi
(103 bar)
(103 bar)
(103 bar)
(103 bar)
System relief valve setting
(at the power supply outlet)
2495 psi
(172 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
2000 psi
(138 bar)
NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements
12 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PREOPERATION PROCEDURES
CHECK POWER SOURCE
IMPORTANT
1. Using a calibrated flowmeter and pressure gauge,
check that the hydraulic power source develops a
flow of 4-6 gpm/15-23 lpm at 1500-2000 psi/105-
140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm
at 1000-2000 psi/70-140 bar for the CS06.
To prevent damage to the retaining ring, do not
attempt to force the selector screw counter-clockwise
beyond the point of initial resistance.
OPERATING PROCEDURES
2. Make certain that the hydraulic power source is
equipped with a relief valve set to open at 2100-
2250 psi/145-155 bar.
The following are general wood cutting procedures and
techniques. Differences in the terrain, vegetation, and
type of wood will make this information more or less val-
id for particular areas. For advice on specific woodcut-
ting problems or techniques for your area, consult your
local Stanley representative or your county agent. They
can often provide information that will make your work
safer and more productive.
CONNECT HOSES
1. Wipe all hose couplers with a clean lint-free cloth
before making connections.
2. Connect the hoses from the hydraulic power source
to the tool fittings or quick disconnects. It is good
practice to connect return hoses first and discon-
nect them last to minimize or avoid trapped pressure
within the tool.
CUTTING TIPS
1. Check the lean of the tree. Tie a weight to a piece
of string about 2 feet long. Hang the weight in your
line of sight. The string is a good vertical line to help
you judge the lean of the tree. The tree should fall
the way it is leaning. Trees that are straight (leaning
no more than 5 degrees) generally can be felled in
any direction.
3. Observe the arrow on the couplers to ensure that
the flow is in the proper direction. The female cou-
pler on the tool hose is the inlet (pressure) coupler.
4. Move the hydraulic circuit control valve to the “ON”
position to operate the tool.
2. Avoid felling across another tree, log, rocks, gully or
ridge. Do not fell straight uphill or downhill. Fell the
tree diagonally to the hill. Consider the wind direc-
tion and velocity. Do not attempt cutting in strong
winds.
NOTE:
If uncoupled hoses are left in the sun, pressure in-
crease inside the hose may make them difficult to
connect. Whenever possible, connect the free ends
of the hoses together.
3. Check the weight distribution. A tree is heavier on
the side with the most limbs. It will try to fall on its
heavy side. Trim a few limbs to “balance” the tree.
SYSTEM SELECTION (OC/CC)
Saws configured with the system selector option require
setup for the system, closed-center (CC) or open-center
(CC), in which it will operate. The selector screw is lo-
cated in the bottom end of the valve spool.
4. Clear the work area. You need a clean area all
around the tree for good footing. Get everything out
of the area where the tree will fall. Do not cut trees
near structures. Because of the danger of electro-
cution, use extreme care when cutting trees near
power lines.
1. Determine the system type.
2. For operation in a CC system, turn the selector
screw fully clockwise. When the selector screw bot-
toms, CC operation is selected.
5. Before starting the cut, prepare your escape path.
Make sure the escape path is clear of brush and
branches. The escape path should be at an angle
away from the direction of fall.
3. For operation in an OC system, turn the selector
screw counter-clockwise until meeting resistance
(from the retaining ring). Turn the selector screw
clockwise and then counter-clockwise to be sure
that you are sensing resistance of the retaining ring.
Do not force the selector screw.
CS05/CS06 User Manual ◄ 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
6. The saw chain should cut with very little pressure
FELLING OR BACK CUT
applied to the handle. If you have to force the saw to
cut or if the cut is not straight, cease cutting immedi-
ately to prevent further saw chain and bar damage.
See the Maintenance and Adjustments section of
the Service Manual for chain replacement or adjust-
ment procedures.
4. The felling or back cut is made on the side opposite
and at least 2 inches above the horizontal undercut
(the felling cut is made higher as the size of the tree
increases). Place the saw so the hand guard is close
to the tree trunk and the bucking cleat is dug in.
5. Start the cut horizontally. Pivot the bar in until the cut
is being made parallel to the notch cut. Cut until the
saw is about 1 or 2 inches from the notch. Do not cut
through the notch.
7. Underwater models require daily preventive mainte-
nance. See the Maintenance and Adjustments sec-
tion of the Service Manual for these maintenance
procedures.
NOTE:
FELLING (CUTTING DOWN A TREE)
(FIGURE 2)
The uncut wood between the felling and notch cuts
is called the hinge. The hinge controls the fall of the
tree and should be of uniform thickness.
Observe all safety precautions.
6. As the saw nears the back cut, watch the treetop
and the cut for signs of movement. Be alert as soon
as the tree starts to move, turn off the saw, pull it
from the tree and move away quickly on your es-
cape route.
7. For trees larger than bar length, make two felling
cuts. Cut in as far as the bar will go, move to the
other side and start the second cut in the same man-
ner as the first while pivoting the saw to complete
the felling cut.
BUCKING
Bucking is the sawing of a log or fallen tree into smaller
pieces.
Figure 2. Felling a Tree
NOTCHING OR UNDERCUTTING
1. Observe all safety precautions.
1. The notching or undercutting cut is made on the side
you want the tree to fall. Place the saw so the hand
guard is close to the tree trunk and the bucking cleat
is dug in.
2. Use both hands. Grip the saw firmly.
3. Stand uphill. A log that is cut loose may role down-
hill.
2. Start the cut horizontally. Pivot the nose of the bar in
4. Keep the chain out of the dirt. Dirt will dull the chain.
last. Cut to about one-quarter of the tree’s diameter.
A dull chain is unsafe.
5. Stand to the left of the saw.
CROSSCUTTING
WARNING
NOTE:
Watch out for falling limbs.
Before starting to cut through a log try to imagine
what is going to happen. Look out for stresses in the
log and cut through the log in such a manner that
the guide bar will not get pinched.
3. Make a diagonal cut down to meet the horizontal cut
and remove the wood from the notch.
14 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOGS WITH PRESSURE ON TOP (FIGURE
3)
1. Observe all safety precautions.
2. Begin with an upper cut, down from the top. Do not
cut too deeply. A cut of about 1/3 of the log diameter
is enough.
3. Finish with a bottom cut. They should meet.
Figure 3. Crosscutting Logs with Pressure on Top
THICK LOGS LARGER THAN BAR LENGTH
WITH PRESSURE ON TOP (FIGURE 4)
1. Observe all safety precautions.
2. Begin by cutting on the opposite side of the log.
3. Pull the saw towards you and cut from the top.
4. Cut from the bottom. Make a boring cut if the log is
close to the ground.
5. Finish with a bottom cut.
Figure 4. Crosscutting Logs Larger than Bar Length
With Pressure on Top
CS05/CS06 User Manual ◄ 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOGS/LIMBS WITH PRESSURE ON
BOTTOM (FIGURE 5)
1. Observe all safety precautions.
2. Begin with a bottom cut. The depth of the cut should
be about 1/3 of the log diameter.
3. Finish with an upper cut, down from the top. The
saw cuts should meet.
Figure 5. Crosscutting Logs/Limbs with
Pressure on Bottom.
THICK LOGS LARGER THAN BAR
LENGTH WITH PRESSURE ON THE
BOTTOM (FIGURE 6)
1. Observe all safety precautions.
2. Begin by cutting on the opposite side of the log.
3. Pull the saw towards you and cut from the top.
4. Cut from the bottom. Make a boring cut if the log is
close to the ground.
5. Finish with a top cut.
Figure 6. Crosscutting Thick Logs with Pressure on
Bottom
16 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PRUNING AND DEBRANCHING
1. Observe all safety precautions.
2. Use both hands. Keep a firm grip.
3. Be alert for kickback. Do not allow the tip of the bar
to touch anything while the chain is in motion.
4. Do not cut overhead. Keep the saw below chest lev-
el. The chain is too close to your face in this position.
COLD WEATHER OPERATION
If the saw is to used during cold weather, preheat the
hydraulic fluid at low engine speed. When using the
normally recommended oils, oil should be at or above
50 °F/10 °C (400 ssu/ 82 centistokes) before use.
Damage to the hydraulic system or saw can result from
use with fluid that is too viscous or thick.
Cutting frozen wood causes the cutters to wear, crack
and break at the back rivet hole unless proper precau-
tions are taken. To extend chain life when cutting in cold
weather:
1. Be sure the oiler is working.
2. Keep the chain tensioned and check often.
3. Keep the cutters properly sharpened. Touch up at
least every hour. Never force a dull chain to cut.
4. Clean out the bar groove and keep the oil hole open.
Turn the bar over to equalize wear on the rails.
5. Always install a new sprocket with a new chain.
CS05/CS06 User Manual ◄ 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL PROTECTION & CARE
NOTICE
In addition to the Safety Precautions found in
this manual, observe the following for equipment
protection and care.
•
•
Make sure all couplers are wiped clean before con-
nection.
•
Do not exceed the rated flow (see Specifications)
page in this manual for correct flow rate and model
number. Rapid failure of the internal seals may re-
sult.
The hydraulic circuit control valve must be in the
“OFF” position when coupling or uncoupling hydrau-
lic tools. Failure to do so may result in damage to
the quick couplers and cause overheating of the hy-
draulic system.
•
•
•
•
Always keep critical tool markings, such as warning
stickers and tags legible.
Tool repair should be performed by experienced
personnel only.
•
•
Always store the tool in a clean dry space, safe from
damage or pilferage.
Make certain that the recommended relief valves
are installed in the pressure side of the system.
Make sure the circuit PRESSURE hose (with male
quick disconnect) is connected to the “IN” port. The
circuit RETURN hose (with female quick disconnect)
is connected to the opposite port. Do not reverse cir-
cuit flow. This can cause damage to internal seals.
Do not use the tool for applications for which it was
not intended.
•
Always replace hoses, couplings and other parts
with replacement parts recommended by Stanley
Hydraulic Tools. Supply hoses must have a mini-
mum working pressure rating of 2500 psi/172 bar.
18 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When
diagnosing faults in operation of the saw, always make sure the hydraulic power source is supplying the correct
hydraulic flow and pressure to the saw as listed in the table. Use a flowmeter known to be accurate. Check the flow
with the hydraulic fluid temperature at least 80 °F/27 °C.
PROBLEM
CAUSE
REMEDY
Cuts slow.
Insufficient fluid flow or low relief Adjust fluid flow to proper gpm. For
valve setting.
optimum performance adjust relief
valve to 2250 psi/155 psi.
Chain dull.
Sharpen per instructions or replace.
Backpressure too high.
Should not exceed 250 psi/17 bar at
8 gpm/30 lpm measured at the end
of the tool operating hoses.
Bar turns color.
Insufficient oiler flow.
Adjust oiler per Service Manual.
Tool does not run.
Power unit not functioning.
Check power unit for proper flow
and pressure (4 gpm/15 lpm at 1500
psi/104 bar minimum for the CS05
and 7 gpm/26 lpm at 1000 psi/70 bar
for the CS06).
Coupler or hoses blocked.
Mechanical failure.
Remove obstruction.
Disassemble tool and inspect for
damage.
Tool runs backwards.
Pressure and return reversed.
Connect for proper flow direction.
Motor shaft rotates clockwise.
On/Off trigger is hard to press.
Pressure and return reversed.
Backpressure too high.
Correct for proper flow direction.
Should not exceed 250 psi/17 bar at
8 gpm/30 lpm measured at the end
of the tool operating hoses.
Oil leakage around drive sprocket.
Motor shaft seal failure.
Replace as required. Make sure that
oil present is not the result of excess
oiler flow.
Oil leakage between rear gear hous- Motor face seal failure.
Replace as required.
ing and valve handle assembly.
Chain continues to move after valve Chain is too loose.
Tighten chain.
Decrease flow.
is shut off.
Input flow too high.
CS05/CS06 User Manual ◄ 19
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Capacity
CS05 .....................................................................................................12 and 15 inch/30 and 38 cm Cut Lengths
CS06 .........................................................................................12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths
Weight (w/o bar) ...................................................................................................................................6.25 lbs/2.8 kg
Length (w/o bar) ................................................................................................................................14 inches/36 cm
Width ...................................................................................................................................................9 inches/23 cm
Pressure
CS05 .............................................................................................................................1500-2000 psi/105-140 bar
CS06 ................................................................................................................................1000-2000 psi/26-34 lpm
Optimum Flow
CS05 ..................................................................................................................................................5 gpm/19 lpm
CS06 ..................................................................................................................................................8 gpm/30 lpm
Porting....................................................................................................................................................8 SAE O-ring
Connect Size and Type ....................................................................................................3/8 inch NPT Male Adapter
Hose Whips............................................................................................................................................................ No
Motor ...............................................................................................................................................................Integral
Kickback Reduction Features
....................Low Kickback Saw Chain, Small Radius Saw Bar, Front Hand Guard, Low Inertia Motor/Drive System
Sound Power Level ....................................................................................................................................... 107 dBA
Sound Pressure Level @ 1 meter ................................................................................................................ 93.1 dBA
Vibration Level..............................................................................................................................................3.1 (m/s2)
ACCESSORIES
Rim Sprocket, .325 P × 7 Tooth.........................................................................................................................07629
12-inch Saw Bar................................................................................................................................................08347
15-inch Saw Bar................................................................................................................................................07638
20-inch Saw Bar................................................................................................................................................07639
Saw Chain for 12-inch Bar.................................................................................................................................08348
Saw Chain for 15-inch Bar.................................................................................................................................07641
Saw Chain for 20-inch Bar.................................................................................................................................07642
File Guide with File............................................................................................................................................12363
Flat File.............................................................................................................................................................. 11294
Scrench ............................................................................................................................................................. 11464
SERVICE TOOLS
O-ring Tool Kit....................................................................................................................................................04337
Seal Kit..............................................................................................................................................................07830
20 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CS05/CS06 PARTS ILLUSTRATION
CS05/CS06 User Manual ◄ 21
Download from Www.Somanuals.com. All Manuals Search And Download.
CS05/CS06 PARTS LIST
ITEM PART
ITEM PART
NO.
NO.
QTY DESCRIPTION
NO.
NO.
QTY DESCRIPTION
33
66578
07618
1
1
2
CHAIN GUIDE PLATE-OUTSIDE
1
00753
09622
8
CAPSCREW
CAPSCREW U/W MODEL
34
CHAIN GUARD
2
07636
08202
1
NAME TAG—CS06
NAME TAG—CS05
35
07631
07722
NUT
NUT U/W MODEL
3
4
28323
07652
07834
00289
04041
00020
07612
1
1
1
2
4
1
1
2
CE DECAL (CE ONLY)
REAR GEAR HSG ASSY (7–9 GPM)
REAR GEAR HSG ASSY (4–6 GPM)
DOWEL PIN
36
00453
00808
1
NUT
NUT U/W MODEL
37
38
39
40
41
07617
07629
07616
06635
1
1
1
1
1
WASHER
RIM SPROCKET
SPROCKET ADAPTER
RET RING
5
6
7
8
9
BUSHING
O-RING
00335
07720
BALL BEARING
BALL BEARING U/W MODEL
IDLER SHAFT
04106
07832
DRIVE GEAR (7–9 GPM)
DRIVE GEAR (4–6 GPM)
42
43
44
45
46
04746
04539
07623
07630
1
1
1
2
1
AUTOMATIC OILER DECAL
WASHER
10
11
—
—
1
NO ITEM
CHAIN CATCHER
STUD
00038
00788
NUT
NUT U/W MODEL
12
13
14
01362
02921
17784
1
1
1
O-RING
02688
02764
CAPSCREW
CAPSCREW U/W MODEL
AUTOMATIC OILER
47
48
49
50
51
04037
07615
04856
04044
1
1
1
2
1
SHAFT SEAL
SOUND POWER LEVEL. DECAL
(CE ONLY)
SEAL BACK-UP WASHER
RETAINING RING
NEEDLE ROLLER
15
16
06971
07724
1
1
LOCKNUT
LOCKNUT U/W MODEL
07620
07714
BAR ADJUSTMENT NUT
BAR ADJUSTMENT NUT U/W MODEL
07613
07710
DRIVE SHAFT
DRIVE SHAFT U/W MODEL
17
18
11354
1
1
OC/CC DECAL (NOT ILLUSTRATED)
52
53
54
55
56
16070
10536
00026
07627
1
1
1
1
1
RETAINING RING
SELECTOR SCREW
O-RING
07632
07723
SCREW
SCREW U/W MODEL
19
00144
00230
1
CAPSCREW
CAPSCREW U/W MODEL
O-RING
20
21
22
23
24
01116
02649
07611
02634
1
2
1
3
1
BUCKING CLEAT
HANDLE BAR RETAINER
HANDLE BAR
00072
00875
ROLL PIN
ROLL PIN U/W MODEL
57
58
07603
1
1
SAFETY CATCH
WASHER
07602
07715
SPRING
SPRING U/W MODEL
00429
09277
NUT
NUT U/W MODEL
59
60
61
62
63
64
34093
03972
03973
28234
01605
1
1
1
2
2
1
TRIGGER CASTING
COUPLER, FEMALE
COUPLER, MALE
HOSE
25
26
27
28
07473
13907
12412
28409
1
1
1
1
HAND GUARD
WARNING DECAL (KICKBACK)
WARNING DECAL (ELECTRIC)
COMPOSITE SAFETY DECAL (CE
ONLY)
O-RING
07693
07713
VALVE HANDLE ASSY
VALVE HANDLE ASSY U/W MODEL
29
07628
02446
3
CAPSCREW
CAPSCREW U/W MODEL
65
66
07624
07718
1
2
ROLL PIN
ROLL PIN U/W MODEL
30
31
66577
08347
07638
07639
08348
07641
07642
1
1
1
1
1
1
1
CHAIN GUIDE PLATE-INSIDE
SAW BAR 12 IN.
03009
03278
ROLL PIN
ROLL PIN U/W MODEL
SAW BAR 15 IN.
67
68
69
70
11207
10535
07626
07609
1
1
1
2
CIRCUIT TYPE D DECAL (CE ONLY)
ON/OFF VALVE SPOOL
O-RING
SAW BAR 20 IN.
32
SAW CHAIN – 12 IN.
SAW CHAIN – 15 IN.
SAW CHAIN – 20 IN.
SPRING WASHER
22 ► CS05/CS06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CS05/CS06 PARTS LIST
ITEM PART
NO.
71
72
73
74
75
NO.
QTY DESCRIPTION
07610
00190
10537
07625
03786
03782
05144
00767
00936
26414
1
1
1
1
1
1
1
1
2
1
SPRING
ROLL PIN
KEEPER
PLUG BUTTON
GPM STICKER (7–9 GPM)
GPM STICKER (4–6 GPM)
BAR & CHAIN GUARD
76
77
GREASE FITTING U/W MODEL ONLY
ADAPTER (NOT SHOWN)
LOCK OUT KIT, SHIPPED INSTALLED
(NOT SHOWN)
03971
07830
1
1
COUPLER SET
SEAL KIT
CS05/CS06 User Manual ◄ 23
Download from Www.Somanuals.com. All Manuals Search And Download.
UNDERWATER TOOLS DEPTH GUIDELINE
UNDERWATER MODELS ONLY
Operation Overview
CAUTION
Percussive
Tools: Breakers,
Hammer Drills and
Chipping Hammers
Rotational
Tools: Grinders,
Saws, Chain Saws
DO NOT USE HYDRAULIC TOOLS UNDER-
WATER THAT ARE NOT DESIGNATED AS
AN “UNDERWATER” MODEL, OR THIS
WILL RESULT IN DAMAGE TO THE TOOL.
Max Depth: 1000' -
Reference hose
sizing guide below
Max Depth: 500' -
limitations due to
accumulator PSI
max (increase 40
PSI for every 100')
For underwater hydraulic tools the applications are
broken down into four quadrants depending on
type of tool and method of operation.
Tools: Breakers,
Hammer Drills and
Chipping Hammers
Tools: Grinders,
Saws, Chain Saws
The types of tools are percussive and rotational,
each with different characteristics allowing for dif-
ferent depth operation. With percussive tools, the
nitrogen accumulator PSI must counter the in-
crease in ambient pressure found at lower depths.
Since there is a maximum PSI for percussive tools
they are limited to certain depths. Rotational tools
do not have accumulators and thus capable of
deeper depths.
Max Depth: 1000' -
Reference hose
sizing guide below
Max Depth: 500' -
limitations due to
accumulator PSI
max (increase 40
PSI for every 100')
The methods are broken into diver operated or
remote operated vehicle (ROV). ROV's can reach
lower depths and with an on-board hydraulic
power source that is depth compensated, can
operate hydraulic tools at depths of thousands of
feet. ROV operation is still limited to the tool, for
example a percussive tool has the same depth
limitation whether ROV or diver operated.
Recommended Hose Diameters
Depth (ft)
100
8 GPM
5/8”
3/4”
1”
12 GPM
5/8”
300
1”
600
1”
1000
1”
1-1/4”
24 ► CS05/06 User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
CS05/06 User Manual ◄ 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, Oregon 97267-5698 USA
(503) 659-5660 / Fax (503) 652-1780
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp MP3 Docking Station DK KP95P User Manual
Shure Car Satellite Radio System PA821 User Manual
Silvercrest Car Stereo System CDV 710 User Manual
Snapper Cultivator 1600223 User Manual
Sony Cassette Player XR C5080R User Manual
Sony MP3 Player D EJ985 User Manual
Speco Technologies TV Converter Box VMW 25LCD User Manual
Sungale Indoor Furnishings CD358LD User Manual
Sungale Tablet ID431WTA User Manual
Symbol Technologies Scanner MK1000 User Manual