CR800
Recumbent
CU800
Upright
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW BIKE!
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS ON YOUR
NEW BIKE AND WELCOME
TO THE SPIRIT FAMILY!
Thank you for your purchase of this quality stationary bike trainer from Spirit
Manufacturing, Inc. Your new bike was manufactured by one of the leading fitness
manufacturers in the world and is backed by one of the most comprehensive warranties
available. Through your dealer, Spirit will do all we can to make your ownership
experience as pleasant as possible for many years to come. The local dealership where
you purchased this bike is your administrator for all Spirit warranty and service needs.
Their responsibility is to provide you with the technical knowledge and service personnel
to make your experience more informed and any difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone
number, and the date of purchase below to make any future, needed contact easy. We
appreciate your support and we will always remember that you are the reason that we
are in business. Please complete and mail your registration card today and enjoy your
new bike.
Yours in Health,
Spirit Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
CR800 & CU800_ver. A
2
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
Before beginning this or any exercise program, consult a physician. This is especially
important for persons over the age of 35 or persons with pre-existing health conditions.
Keep children away from the bike. There are obvious pinch points and other areas of
caution that can cause harm.
Keep hands away from all moving parts.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from the outlet.
Do not attempt to use your
intended.
for any purpose other than for the purpose it is
bike
The hand pulse sensors are not medical devices. Various factors, including the users
movement, may affect the accuracy of heart rate readings. The pulse sensors are intended
only as exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your bike. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
3
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Electrical Information
WARNING!
• When pedaling be aware that the generator is producing A.C. power while the bike is being
used. Do not service the bike while the generator is spinning. Serious electric shock
could occur.
•
Never expose the bike to rain or moisture. This product is NOT designed for
Use outdoors, near a pool or spa, or in any other high humidity environment. Maximum
environmental ratings are 40-120 degrees Fahrenheit, 95% humidity non-condensing (no
water droplets forming on surfaces).
Important Operation Instructions
Never operate the bike without reading and completely understanding the results of any
operational change you request from the computer.
Do not use excessive pressure on console control keys. They are precision set to properly
function with little finger pressure. Pushing harder is not going to make the unit go faster or
slower. If you feel the buttons are not functioning properly with normal pressure, contact
your Spirit dealer.
4
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Pack Check List For CR800
Step 1
#174 - 3/8´ x 5/8´
#77 - 3/8" Flat
#84 - 3/8" Flat
Hex Head Bolt (6pcs)
Washer (6pcs)
Washer (4pcs)
#65 - 3/8´ x 2-1/4´
Hex Head Bolt (4pcs)
Step 2
#77 - 3/8" Flat
#71 - 3/8´ x 1-3/4´
Hex Head Bolt (2pcs)
Washer (6pcs)
#89 - 3/8"
3/8´ x 2-3/4´
#175 -
Nylon Nut (2pcs)
Hex Head Bolt (2pcs)
5
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
#68 - 5/16´ x 5/8´
#83 - 5/16"
Hex Head Bolt (8pcs)
Curved Washer (2pcs)
#76 - 5/16"
#82 - 5/16´
Flat Washer (6pcs)
Split Washer (2pcs)
Step 4
#98 - M6 x 15mm
Phillips Head Screw (4pcs)
#99 - M5 x 12mm
Phillips Head Screw (8pcs)
#105 – 4mm x 16mm
Self Tapping Screw (4pcs)
6
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
#112 - 12/14mm Wrench (1 pc)
#132 - 14/15mm Wrench (1 pc)
Phillips Screw Driver (1 pc)
#114 -
7
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions For CR800
STEP 1: REAR STABILIZER & SEAT BACK ASSEMBLY
1. Install the Rear Stabilizer (7) onto the Main Frame with four 3/8´ x 2-1/4´ Hex Head bolts (65)
and four 3/8´ Flat Washers (84).
2. Install Seat Back Frame (5) onto the Seat Carriage (4) with six 3/8´ x 5/8´ Hex Head bolts (176)
and 3/8´ flat washers (77).
8
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2: REAR HANDLEBARS
1. Install the rear handlebars (6) to the seat carriage (4). First install two 3/8´ x 1-3/4´ bolts (71)
through the top holes in the handlebars and fix with two 3/8´ nuts (89) and flat washers (77)
from the bottom.
2. Install two 3/8´ x 2-3/4´ bolts (175) through the side holes in the handlebars and fix with two 3/8´
nuts (89) and flat washers (77).
3. Connect the hand pulse wires (21, 27) to the mating connectors mounted in the left side cover
(35).
9
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3: CONSOLE MAST ASSEMBLY
1. Install the console mast cover (31) onto the console mast (2), making sure it is facing the correct
direction as in the picture below. Run the two wire harnesses through the bottom of the console
mast tube and out the top opening.
2. Slide the console mast into the receiving tube (1) being careful to not pinch the wires. Fasten the
console mast with six 3/8´ x 5/8´ bolts (68) and four 3/8´ flat washers (76) on the side bolts and two
3/8´ curved washers (83) on the front bolts. Snap the console mast cover in place.
3. Install the front handlebars (3) onto the console mast with two 3/8´ x 5/8´ bolts (68), 3/8´ split
washers (82) and 3/8´ flat washers (76).
10
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4: CONSOLE, SEAT, COVERS, PEDALS
1. Install the front and rear stabilizer covers (32 & 37) and secure to the frame with four M5 x 12mm
screws (99).
2. Install the left and right cup holders (39 & 38) to the rear handlebars with four self tapping screws
(105).
3. Install the bottom seat cushion (61) to the seat carriage (4) with four M6 x 15mm screws (98).
4. Install the Pedals (116 L, 117 R) into the Crank arms (51L, 51R). Remember that the left pedal has
a reverse thread and will be screwed into the crank in the opposite rotation from normal threads.
There is an ³/´ stamped into the end of the threaded post of the left pedal and an ³5´ in the right.
Make sure to tighten the pedals as much as you possibly can. It may be necessary to re-tighten
the pedals if you feel a thumping during pedaling the bike. A clicking noise, or thumping, sound
during pedaling is usually caused by the pedals being too loose.
5. Connect the two wire harnesses (44 & 45) to the corresponding connectors on the back of the
console. Install the console onto the console mast and secure with four M5 x 12mm screws being
careful to not pinch the wires.
11
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Pack Check List For CU800
Step 1
#50 - 3/8´ x 2-1/4´
Hex Head Bolt (4pcs)
#71 - 3/8" Flat
Washer (4pcs)
Step 2
#51 - 5/16´ x 5/8´
Hex Head Bolt (7pcs)
#99 - 5/16"
Curved Washer (1pcs)
#72 - 5/16"
Flat Washer (6pcs)
Step 3
#72 - 5/16"
Flat Washer (2pcs)
#51 - 5/16´ x 5/8´
Hex Head Bolt (2pcs)
#103 - 5/16´
Split Washer (2pcs)
Step 4
#58 - M5 x 12mm Phillips
Head Screw (10pcs)
12
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools
12/14mm Wrench (1pc)
13/15mm Wrench (1pc)
#117.
#100 -
#93 - Phillips Screw Driver (1pc)
13
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1: REAR STABILIZER ASSEMBLY
1. Install the Rear Stabilizer (5) onto the Main Frame (1) with the four 3/8´ x 2-1/4´ Hex Head
Bolts (50) and four 3/8´ Flat Washers (71).
14
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2: FRONT CONSOLE MAST ASSEMBLY
1. Unravel the Computer Cable (29) and snake it through the Console Mast Cover (38) and the
Console Mast (2) until the cable connector comes out the top opening of the console mast.
Slide the plastic cover (38) onto the console mast, ensuring the correct orientation of the cover.
2. Install the Console Mast (2) onto the Main Frame (1) with seven 5/16´ x 5/8´ Hex Head bolts
(51), six 5/16´ Flat Washers (72) on the side screws and one 5/16´ Curved Washer (99) on the
front screw.
15
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3: HANDLE BAR ASSEMBLY
1. Run the two hand pulse wires (26) into the hole in the handle bar mounting plate and out
through the hole in the console plate. Install the Handle Bar (3) onto the Console Mast (2) with
two 5/16´ x 5/8´ Hex Head bolts (51), two 5/16´ Flat Washers (72) and two 8mm Split Washers
(103) being careful not to pinch the hand pulse wires.
16
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4: CONSOLE, SEAT, PEDALS AND BEAUTY COVERS ASSEMBLY
1. Insert the Computer Cable (29) and two Hand pulse cables (26) into the connectors in the back
of the Console (34). Install the Console (34) onto the Console Mast (2) with four M5x12mm
Phillips Head Screws (58).
2. Install the Front Stabilizer Cover (40) and the Rear Stabilizer Cover (41) onto the Main Frame (1)
with four M5x12mm Phillips Head Screws (58).
3. Install the Pedals (45 L, 46R) onto the Crank arms (16L, 16R). Remember that the left pedal
has a reverse thread and will be screwed into the crank in the opposite rotation from normal
threads. There is an ³/´ stamped into the end of the threaded post of the left pedal and an ³5´
in the right. Make sure to tighten the pedals as much as you possibly can. It may be necessary
to re-tighten the pedals if you feel a thumping during pedaling the bike. A noise or feeling such
as a thumping or clicking is usually caused by the pedals being too loose.
4. Install the Seat mount slide (7) onto the track on top of the seat tube with the seat post facing
forward. Install the seat (19) onto the seat post.
17
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Foot pedals
Through research performed with a leading sports scientist and physical rehabilitation expert,
Spirit engineering has developed a breakthrough in pedal design. Typical stationary exercise
bikes are wider than a normal road bike. The reason is to allow for the braking mechanism,
pulleys, drive components and beauty covers. Since the bike is wider, so is the distance
between the pedals; this width between the pedals is called the Q factor.
Spirit has designed our pedal system so the Q factor is the smallest in the industry, but we did not
stop there. We have also custom designed and tooled a new pedal that provides a two degree
inward tilt to compensate for the Q factor not being perfect. Having a small Q factor in addition to
the two degree inward tilt of the pedals puts the user into a biomechanical neutral alignment. This
means that your feet, ankles, knees and hips are lined up properly ensuring a comfortable
workout.
Transportation
The bike is equipped with two transport wheels, which are engaged when rear of the bike is lifted.
18
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of Your Stationary Bike
CR800 & CU800 Console
Power on
Spirit commercial bikes have a built-in generator for power and do not need to be plugged into an
AC outlet. To power up the Bike simply start to pedal, the console will turn on automatically.
When initially powered on the console will perform an internal self-test. During this time all the
lights will turn on for a short time. When the lights go off the dot matrix display will show a software
version (i.e. VER 1.0) and the message window will display an odometer reading. The odometer
reading displays how many hours the bike has been used and how many virtual miles the bike has
gone. The display shows: ODO 123 MI 123 HRS.
The odometer will remain displayed for only a few seconds then the console will go to the start up
display. The dot matrix display will be scrolling through the different profiles, showing the programs,
and the message window will be scrolling the start up message. You may now begin to use the
console.
19
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Operation
Quick Start
This is the quickest way to start a workout. After the console powers up you just press the Start
key to begin. This will initiate the Quick Start mode. In Quick Start the Time will count up from zero,
all workout data will start to accrue and the workload may be adjusted manually by pressing the
Up and Down buttons. The dot matrix display will show a ¼ mile track display or just the bottom
row lit at first, depending on how the display button has been set (see Basic information below). As
you increase the workload more rows will light indicating a harder workout. The bike will get harder
to pedal as the rows increase. The dot matrix has 24 columns of lights and each column
represents 1 minute. At the end of the 24th column (or 24 minutes of work) the display will wrap
around and start at the first column again.
There are 40 levels of resistance ± displayed as 10 rows of lights - available for plenty of variety.
The first 10 levels are very easy workloads, and the changes between levels are set to a good
progression for de-conditioned users. Levels 10-20 are more challenging but the increases from
one level to the next remain small. Levels 20-30 start getting tough as the levels jump more
dramatically. Levels 30-40 are extremely hard and are good for short interval peaks and elite
athletic training.
Basic information
The Dot Matrix, or Profile Window, has two display modes. When you begin a program the dot
matrix will display the workout Profile. To the left of the dot matrix there is a button labeled Display.
Pressing this button once will switch the display to show a quarter mile track. If the Display button
is pressed again the dot matrix will switch back and forth between Track and Profile mode every
few seconds. To turn off the scan mode press the Display key again. This will return you to the
profile display mode.
The Message Window will initially be displaying Time and Distance information. On the bottom
left of the message window is a button labeled Display. Each time this Display button is pressed
the next set of information will appear, four windows in all. In order: Time and Distance, Pulse and
Kcal (Calories), Speed in RPM and MPH, Work Level and Watts, then METs. If the Display button
is pressed during the METs display the Scan light will come on and the message window will show
each set of data for four seconds then switch to the next set of data in a continuous loop. Pressing
the Display button again will bring you back to the beginning.
Below the Dot matrix display is a Heart Icon and a Bar Graph. The Bike has a built in heart rate
monitoring system. Simply grasping the hand pulse sensors, or wearing a heart rate chest belt
transmitter, will start the Heart Icon blinking (this may take a few seconds). The Message Window
will display your heart rate, or Pulse, in beats per minute. The Bar Graph represents the
percentage of your maximum heart rate you are currently achieving. NOTE: You must enter your
age during program setup for the Bar Graph to be accurate. Refer to Heart Rate section for details
about these features and how they can help you work out more efficiently.
The Stop/Reset button actually has several functions. Pressing the Stop/Reset key once during a
program will Pause the program for 5 minutes (when you stop pedaling without AC power the
display will turn off but the memory will be saved for 5 minutes just like the pause mode). If you
need to get a drink, answer the phone, or any of the many things that could interrupt your workout,
20
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
this is a great feature. To resume your workout during Pause just press the Start key or start
pedaling. If the Stop/Reset button is pressed twice during a workout the program will end and the
console will return to the start up screen. If the Stop/Reset key is held down for 3 seconds the
console will perform a complete Reset. During data entry for a program the Stop/Reset key
performs a Previous Screen function. This allows you to go back one step in the programming
each time you press the Stop/Reset key.
The Program Keys are used to preview each program. When you first turn the console on you
may press each program key to preview what the program profile looks like. If you decide that you
want to try a program, press the corresponding program key and then press the Enter key to
select the program and enter into the data-setup mode.
The program keys also act as a Number Key Pad when you are in the data-setup mode. Under
each program key is a number. If you are setting new data such as Age, weight etc., you can use
these keys to enter the numbers quickly.
The console includes a built-in fan to help keep you cool. To turn the fan on press the key on the
right side, front of the console
Programming the console
Each of the programs can be customized with your personal information and changed to suit your
needs. Some of the information asked for is necessary to ensure the readouts are correct. You will
be asked for your Age and Weight. Entering your Age ensures that the Heart Rate bar graph
shows the correct number. Your Age is also necessary during the Heart Rate control program to
ensure the correct settings are in the program for your Age. Otherwise the work settings could be
too high or low for you; entering your Weight aides in calculating a more correct Calorie reading.
Although we cannot provide an exact calorie count we do want to be as close as possible.
Entering/Changing Settings
When you enter a program (by pressing a program key, then enter key) you have the option of
entering your own personal settings. If you want to workout without entering new settings then just
press the Start key. This will bypass the programming of data and take you directly to the start of
your workout. If you want to change the personal settings then just follow the instructions in the
message window. If you start a program without changing the settings the default - or pre-saved ±
settings will be used.
21
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual
The Manual program works as the name implies, manually. This means that you control the
workload yourself and not the computer. To start the Manual program follow the instructions below
or just press the Manual button then the Enter button and follow the directions in the message
window.
1. Press the Manual key then press the Enter key.
2. The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
3. You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys, or the numeric key pad, then press enter to continue.
4. The next setting is Time. You may adjust the Time and press enter to continue.
5. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At
any time during the editing of Data you can press the Stop key to go back one level, or
screen.
6. The program automatically starts you at level one. This is the easiest level and it is a good
idea to stay at level one for a while to warm up. If you want to increase the work load at any
time press the Up key; the Down key will decrease the workload.
7. During the Manual program you will be able to scroll through the data in the message
window by pressing the adjacent Display key. You may also switch between the profile
display and a quarter mile track by pressing the Display key adjacent to the dot matrix
display.
8. When the program ends you may press Start to begin the same program again or Stop to
exit the program, or you can save the program you just completed as a custom program
by pressing the Custom key and following the instructions in the message window.
Preset Programs
The bike has five different programs that have been designed for a variety of workout goals.
These five programs have factory preset profiles for achieving these different goals. The initial
built-in level of difficulty for each program is set to a relatively easy level. You may adjust the level
of difficulty (Max level) for each program before beginning by following the instructions in the
message window after selecting your program.
HILL
The Hill program simulates going up and down a hill. The resistance in the pedals will steadily
increase and then decrease during the program.
Work Profile
22
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
FATBURN
The Fat Burn program is designed, as the name implies, to maximize the burning of fat. There are
many schools of thought on the best way to burn fat but most experts agree that a lower exertion
level that stays at a steady workload is the best. The absolute best way to burn fat is to keep your
heart rate at around 60% to 70% of its maximum potential. This program does not use heart rate
but simulates a lower, steady exertion workout.
Work Profile
Cardio
The Cardio program is designed to increase your Cardio vascular function. This is exercise for
your heart and lungs. It will build up your heart muscle and increase blood flow and lung capacity.
This is achieved by incorporating a higher level of exertion with slight fluctuations in work.
Work Profile
Strength
The Strength program is designed to increase muscular strength in your lower body. This
program will steadily increase in resistance to a high level and then keeps you there. This is
designed to strengthen and tone your legs and glutes.
Work Profile
23
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Interval
The Interval program takes you through high levels of intensity followed by periods of low intensity.
This program increases your endurance by depleting your oxygen level followed by periods of
recovery to replenish oxygen. Your cardio vascular system gets programmed to use oxygen more
efficiently this way.
Work Profile
Programming Preset Programs:
1. Select the desired program button then press the Enter key.
2. The message window will ask you to enter your Age. You may adjust the age setting, using
the Up and Down keys, then press the Enter key to accept the new number and proceed on
to the next screen.
3. You are now asked to enter your Weight. You may adjust the weight number using the Up
and Down keys, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program (at the top of the hill). Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will change the workload settings of the entire profile, although the profile
picture on the screen will not change. The reason for this is so that you can see the entire
profile at all times. If the profile picture is changed it will look distorted and not a true
representation of the actual profile. When you make a change to the workload, the message
window will show the current column, and program maximum, levels of work.
8. During the program you will be able to scroll through the data in the message window by
pressing the Display key next to the message window.
9. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time then the console will return to the start-up display.
24
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom User Defined Program
The custom program allows you to build and save a custom program. You can build your own
custom program by following the instructions below or you can save any other preset program you
complete as a custom program. The custom program allows you to further personalize it by adding
your facility name.
1. Press the Custom key. The message window will show a welcome message; if you had
previously saved a program the message will contain the name you gave it. Then press the
Enter key to begin programming.
2. When you press enter, the message window will show ³Name ± A´, if there is no name saved.
If the name ³Custom Workout´ had been previously saved the message window will show
³Name ± Custom Workout´ and the C in Custom will be blinking. If there is a name saved you
can change it or you may press the Stop key to keep the name and continue to the next step.
If you want to enter a name use the Up and/or the Down key to change the first letter then
press Enter to save the first letter and continue to the next letter. When you have finished
entering the name press the Stop key to save the name and continue to the next step.
3. The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
4. You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad then press enter to continue.
5. Next is Time. You may adjust the Time and press enter to continue.
6. Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program. Adjust the level and then press enter.
7. Now the first column will be blinking and you are asked to adjust the level for the first segment
of the workout. When you finish adjusting the first segment, or if you don¶t want to change,
then press enter to continue to the next segment.
8. The next segment will show the same level as the previously adjusted segment. Repeat the
same process as the last segment then press enter. Continue this process until all twenty
segments have been set.
9. The message window will then tell you to press enter to save the program. After saving the
program the message window says ³New program saved´ then will give you the option to
Start or modify the program. Pressing Stop will exit to the start up screen.
10.If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
11.During the User 1 or User 2 program you will be able to scroll through the data in the
message window by pressing the adjacent Display key, switch between the profile display
and a quarter mile track by pressing the Display key adjacent to the matrix, use the heart rate
monitoring features and can switch to heart rate Auto-Pilot mode. See Heart Rate section for
details of this feature).
25
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Fit-Test
The fitness test is based on the YMCA protocol and is a sub-maximal test that uses
pre-determined, fixed work levels that are based on your heart rate readings as the test
progresses. The test will take anywhere between 6 to 15 minutes to complete, depending on your
level of fitness. The test ends when your heart rate reaches 85% of maximum at any time during
the test or your heart rate is between 110 bpm and 85% at the end of two consecutive stages. At
the end of the test a VO2max score will be given. VO2max stands for Volume of Oxygen uptake which
is a measurement of how much oxygen you need to perform a known amount of work.
The YMCA protocol uses two to four, 3 minute stages of continuous exercise (see charts below).
You will be asked to choose either, Male or Female at the beginning of the test. This choice
determines which test parameters will be used during the test as shown in the charts below. The
only caveats are that if you are a very de-conditioned Male you need to choose option Female. If
you are a very conditioned female you need to choose option Male.
Workload chart for male or very fit female:
Level 12 -
50 watts -
300 kgm/min
1st
Stage
HR
< 90
90 - 105
> 105
Level 29 -
Level 26 -
Level 23 -
2nd
Stage
150 watts -
125 watts -
100 watts -
900 kgm/min
750 kgm/min
600 kgm/min
HR
HR
HR <120
HR 120-135
Level 34 -
200 watts -
1200 kgm/min
HR >135
HR <120
HR 120-135
Level 32 -
175 watts -
1050 kgm/min
HR >135
HR <120
120-135
HR >135
Level 36 -
225 watts -
1350 kgm/min
Level 32 -
175 watts -
1050 kgm/min
Level 34 -
200 watts -
1200 kgm/min
Level 29 -
150 watts -
900 kgm/min
Level 32 -
175 watts -
1050 kgm/min
Level 29 -
150 watts -
900 kgm/min
Level 26 -
125 watts -
750 kgm/min
3rd
stage
Workload chart for female or de-conditioned male
Level 5 (25W)
150 kgm/min
1st Stage
HR<80
HR: 80-90
HR: 90-100
HR>100
Heart Rate
2nd Stage
Level 23 (100W)
600 kgm/min
Level 18 (75W)
450 kgm/min
Level 12 (50W)
300 kgm/min
Level 26 (125W) 750 kgm/min
Level 29 (150W)
900 kgm/min
Level 26 (125W)
750 kgm/min
Level 23 (100W)
600 kgm/min
Level 18 (75W)
450 kgm/min
3rd Stage
Level 32 (175W)
1050 kgm/min
Level 29 (150W)
900 kgm/min
Level 25 (117W)
700 kgm/min
Level 23 (100W)
600 kgm/min
4th Stage (if needed)
26
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitness test programming:
1. Press the Fit-test button and press enter.
2. The message window will ask you to enter your Age. You may adjust the age setting, using
the Up and Down keys then press the Enter key to accept the new number and proceed on
to the next screen.
3. You are now asked to enter your Weight. You may adjust the weight number using the Up
and Down keys then press enter to continue.
4. Now press Start to begin the test.
Before the test:
·
·
Make sure you are in good health; check with your physician before performing any exercise if
you are over the age of 35 or persons with pre-existing health conditions.
Adjust the seat to the proper position so that when your leg is extended during pedaling there
is a slight bend at the knee of about 5 degrees.
·
·
·
Make sure you have warmed up and stretched before taking the test.
Do not take in caffeine before the test.
Hold the hand grips gently, do not tense up.
During the test:
·
·
The console must be receiving a steady heart rate for the test to begin. You may use the hand
pulse sensors or wear a heart rate chest strap transmitter.
You must maintain a steady 50 RPM pedal speed. If your pedal speed drops below 48 RPM or
goes above 52 RPM the console will emit a steady beeping sound until you are within this
range.
·
You may scroll through the various data readings in the message window by pressing the
Display button under the message window.
1. The message window will always display your pedal speed on the right side to help you
maintain 50RPM.
2. The data shown during the test is:
a. Work in KGM is actually an abbreviated form of kg-m/min. which is a work
measurement of kilogram-force meter/minute
b. Work in Watts (1 watt is equal to 6.11829727787 kg-m/min.)
c. HR is your actual heart rate; TGT is the target heart rate to reach to end the test.
d. Time is the total elapsed time of the test.
After the test:
·
·
Cool down for about one to three minutes.
Take note of your score because the console will automatically return to the start-up mode after
a few minutes.
27
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
What your score means:
VO2max Chart for males and very fit females
18-25 26-35 36-45 46-55 56-65 65+
years
old
years
old
years
old
years
old
years
old
years
old
excellent
good
>60
>56
>51
>45
>41
>37
52-60 49-56 43-51 39-45 36-41 33-37
above
average
47-51 43-48 39-42 35-38 32-35 29-32
42-46 40-42 35-38 32-35 30-31 26-28
average
below
average
37-41 35-39 31-34 29-31 26-29 22-25
30-36 30-34 26-30 25-28 22-25 20-21
poor
very poor
<30
<30
<26
<25
<22
<20
VO2max Chart for females and de-conditioned males
18-25 26-35 36-45 46-55 56-65 65+
years
old
years
old
years
old
years
old
years
old
years
old
excellent
good
56
52
45
40
37
32
47-56 45-52 38-45 34-40 32-37 28-32
above
average
42-46 39-44 34-37 31-33 28-31 25-27
38-41 35-38 31-33 28-30 25-27 22-24
average
below
average
33-37 31-34 27-30 25-27 22-24 19-22
28-32 26-30 22-26 20-24 18-21 17-18
poor
very poor
<28
<26
<22
<20
<18
<17
28
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Heart Rate Training
A word about Heart Rate:
The old motto, ³no pain, no gain´, is a myth that has been overpowered by the benefits of exercising
comfortably. A great deal of this success has been promoted by the use of heart rate monitors. With
the proper use of a heart rate monitor, many people find that their usual choice of exercise intensity
was either too high or too low and exercise is much more enjoyable by maintaining their heart rate in
the desired benefit range.
To determine the benefit range in which you
wish to train, you must first determine your
Maximum Heart Rate. This can be
accomplished by using the following formula:
220 minus your age. This will give you the
Maximum heart rate (MHR) for someone of your
age. To determine the effective heart rate range
for specific goals you simply calculate a
percentage your MHR. Your Heart rate training
zone is 50% to 90% of your maximum heart rate.
60% of your MHR is the zone that burns fat
while 80% is for strengthening the cardio
vascular system. This 60% to 80% is the zone
to stay in for maximum benefit.
90
For someone who is 40 years old their target
heart rate zone is calculated:
220 ± 40 = 180 (maximum heart rate)
180 x .6 = 108 beats per minute (60% of maximum)
180 X .8 = 144 beats per minute (80% of maximum)
So for a 40 year old the training zone would be 108 to 144 beats per minute.
If you enter your age during programming the console will perform this calculation automatically.
Entering your age is used for the Heart Rate control programs. After calculating your Maximum Heart
Rate you can decide upon which goal you would like to pursue.
The two most popular reasons for, or goals, of exercise are cardiovascular fitness (training for the
heart and lungs) and weight control. The black columns on the chart above represent the Maximum
Heart Rate for a person whose age is listed at the bottom of each column. The training heart rate, for
either cardiovascular fitness or weight loss, is represented by two different lines that cut diagonally
through the chart. A definition of the lines¶ goal is in the bottom left-hand corner of the chart. If your
goal is cardiovascular fitness or if it is weight loss, it can be achieved by training at 80% or 60%,
respectively, of your Maximum Heart Rate on a schedule approved by your physician. Consult your
physician before participating in any exercise program.
With all Spirit Heart Rate Control bike machines you may use the heart rate monitor feature without
using the Heart Rate Control program. This function can be used during manual mode or during any of
the nine different programs. The Heart Rate Control program automatically controls resistance at the
pedals.
29
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Rate of Perceived Exertion
Heart rate is important but listening to your body also has a lot of advantages. There are more
variables involved in how hard you should workout than just heart rate. Your stress level, physical
health, emotional health, temperature, humidity, the time of day, the last time you ate and what
you ate, all contribute to the intensity at which you should workout. If you listen to your body, it will
tell you all of these things.
The rate of perceived exertion (RPE), also know as the Borg scale, was developed by Swedish
physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending upon how you
feel or the perception of your effort.
The scale is as follows:
Rating Perception of Effort
6 Minimal
7 Very, very light
8 Very, very light +
9 Very light
10 Very light +
11 Fairly light
12 Comfortable
13 Somewhat hard
14 Somewhat hard +
15 Hard
16 Hard +
17 Very hard
18 Very hard +
19 Very, very hard
20 Maximal
You can get an approximate heart rate level for each rating by simply adding a zero to each rating.
For example a rating of 12 will result in an approximate heart rate of 120 beats per minute. Your
RPE will vary depending up the factors discussed earlier. That is the major benefit of this type of
training. If your body is strong and rested, you will feel strong and your pace will feel easier. When
your body is in this condition, you are able to train harder and the RPE will support this. If you are
feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will
feel harder. Again, this will show up in your RPE and you will train at the proper level for that day.
30
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Heart Rate Transmitter
How to wear your wireless chest strap transmitter:
1. Attach the transmitter to the elastic strap using the locking parts.
2. Adjust the strap as tightly as possible as long as the strap is not too tight to remain comfortable.
3. Position the transmitter with the logo centered in the middle of your body facing away from your
chest (some people must position the transmitter slightly left of center). Attach the final end of
the elastic strap by inserting the round end and, using the locking parts, secure the transmitter
and strap around your chest.
4. Position the transmitter immediately below the pectoral muscles.
5. Sweat is the best conductor to measure very minute heart beat electrical signals. However,
plain water can also be used to pre-wet the electrodes (2 black square areas on the reverse
side of the belt and either side of transmitter). It¶s also recommended that you wear the
transmitter strap a few minutes before your work out. Some users, because of body chemistry,
have a more difficult time in achieving a strong, steady signal at the beginning. After ³warming
up´, this problem lessens. As noted, wearing clothing over the transmitter/strap doesn¶t affect
performance.
6. Your workout must be within range - distance between transmitter/receiver ± to achieve a
strong steady signal. The length of range may vary somewhat but generally stay close enough
to the console to maintain good, strong, reliable readings. Wearing the transmitter immediately
against bare skin assures you of proper operation. If you wish, you may wear the transmitter
over a shirt. To do so, moisten the areas of the shirt that the electrodes will rest upon.
Note: The transmitter is automatically activated when it detects activity from the user’s heart. Additionally, it
automatically deactivates when it does not receive any activity. Although the transmitter is water resistant, moisture
can have the effect of creating false signals, so you should take precautions to completely dry the transmitter after
use to prolong battery life (estimated transmitter battery life is 2500 hours). If your chest strap has a replaceable
battery the replacement battery is Panasonic CR2032.
Erratic Operation:
Caution! Do not use this bike for Heart Rate Control unless a steady, solid Actual Heart
Rate value is being displayed. High, wild, random numbers being displayed indicate a
problem.
Areas to look at for interference, which may cause erratic heart rate:
(1) Microwave ovens, TVs, small appliances, etc.
(2) Fluorescent lights.
(3) Some household security systems.
(4) Perimeter fence for a pet.
(5) Some people have problems with the transmitter picking up a signal from their skin. If you have
problems try wearing the transmitter upside down. Normally the transmitter will be oriented so
the Spirit logo is right side up.
(6) The antenna that picks up your heart rate is very sensitive. If there is an outside noise source,
turning the whole machine 90 degrees may de-tune the interference.
(7) If you continue to experience problems contact your dealer.
31
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Heart Rate Control (HR) Program operation
To start the HR program follow the instructions below or just press the HR key then the Enter
button and follow the directions in the message window.
1. Press the HR key then press the Enter key.
2. The message window will ask you to enter your Age. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
3. You are now asked to enter your Weight. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
4. Next is Time. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the Heart rate Level. This is the heart rate level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will allow you to change your target heart rate at any time during the
program.
8. During the HR program you will be able to scroll through the data in the message window by
pressing the adjacent Display key.
9. When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a custom user program by
pressing a User key and following the instructions in the message window.
Auto-pilot
The Auto-pilot feature is a unique heart rate program. This program allows you to enter the Heart
Rate Control (HR) program on the fly. At any time, during any program, you can press the
Auto-pilot button and the console will switch to heart rate control (HR) mode. The console will
maintain your heart rate at the current level it is at when you press the Auto-pilot button. For
instance: If you are in the Manual mode and your heart rate is at 150 beats per minute, pressing
the Auto-pilot button will switch the console to heart rate control (HR) and keep your heart rate at
150 beats per minute automatically.
32
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance:
1. Wipe down all areas in the sweat path with a damp cloth after each workout.
2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two
reasons:
1) The hardware was not sufficiently tightened during assembly. All bolts that were
installed during assembly need to be tightened as much as possible. It may be
necessary to use a larger wrench than the one provided if you cannot tighten the bolts
sufficiently. I cannot stress this point enough; 90% of calls to the service department
for noise issues can be traced to loose hardware.
2) The crank arm nut and/or the pedals need to be retightened.
3. If squeaks or other noises persist, check that the unit is properly leveled. There are 2 leveling
pads on the bottom of the rear stabilizer, use a 14mm wrench (or adjustable wrench) to adjust
the levelers.
Maintenance Menu in console software:
The console has built in maintenance/diagnostic software. The software will allow you to change
the console settings from English to Metric and turn off the beeping of the speaker when a key is
pressed for example. To enter the Maintenance menu (may be called Engineering mode,
depending on version) press and hold down the Start, Stop and Enter keys. Keep holding the keys
down for about 5 seconds and the message window will display ³ALTXXXX Engineering mode´.
Press the enter button to access the menu below:
a. Key test (will allow you to test all the keys to make sure they are functioning)
b. Display test (tests all the display functions)
c. Functions (Press enter to access settings)
i. Sleep mode (Turn on to have the console power down automatically after
20 minutes of inactivity)
ii. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the
console pause indefinitely)
iii. ODO reset (reset the odometer)
iv. Units (Set to English or Metric display readings)
v. Beep (Turn on or off the beep when a key is pressed)
vi. D/A test (tests the brake resistance)
vii. Exit
d. Security (Allows you to lock the keypad so no unauthorized use is allowed)
e. Factory settings (Access only allowed by manufacturing)
33
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer’s Limited Warranty
Effective July 15, 2009
BIKE LIMITED WARRANTY
Spirit Fitness Inc. warrants all its home use bike parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the
absence of a sales receipt, eighteen (18) months from the original factory shipping date. Spirit s responsibilities include providing new or remanufactured
parts, at Spirit s option, and technical support to our independent dealers and servicing organizations. In the absence of a dealer or service organization,
these warranties will be administered by Spirit Fitness directly to a consumer. The warranty period applies to the following components:
WARRANTY
Light Institutional**
Residential
Frame
Mech. Parts
5 Years
Electronics
5 Years
Wear Items *
6 Months
Labor
Lifetime
Lifetime
2 Years
2 Years
10 Years
10 Years
6 Months
* Wear items are rubber hand grips, pedals, console overlay and drive belts
** 5 Hours use or less per day
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use or in a non-dues paying, light commercial facility with 5 hours elliptical use or less per day.
The consumer or light commercial facility is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to validate the
2. Proper use of the bike in accordance with the instructions provided in this manual, including maintenance.
3. Proper connection to a power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house/facility wiring.
4. Expenses for making the bike accessible for servicing, including any item that was not part of the bike at the time it was shipped from the factory.
5. Damages to the bike finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or defects in workmanship or
material, for units that are beyond the warranty period, for units that are beyond the service call reimbursement period, for units not requiring component
replacement, or units not in ordinary household use.
3. Damages caused by services performed by persons other than authorized Spirit Fitness service companies, use of parts other than original Spirit parts, or
external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been; sold, transferred, bartered, or given to a third party.
6. Products that are used as store display models.
7. Products that do not have a warranty registration on file at Spirit Fitness, inc. Spirit Fitness reserve the right to request proof of purchase if no warranty
record exists for the product.
8. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory shipping as determined by the
serial number establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This
written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by
following these steps, in order:
1. Contact your selling authorized Spirit Fitness dealer. OR
2. Contact your local authorized Spirit Fitness service organization.
3. If there is a question as to where to obtain service, contact our service department at (870) 935-1107.
4. Spirit s obligation under this warranty is limited to repairing or replacing, at Spirit s option, the product through one of our authorized service centers. All
repairs must be preauthorized by Spirit. If the product is shipped to a service center freight charges to and from the service center will be the customer s
responsibility. For replacement parts shipped while the product is under warranty, the customer will be responsible for shipping and handling charges. For
in-home service, the customer will be responsible for a trip charge. There will be an additional trip charge if the customer is located over 100 miles from the
nearest service center.
5. The owner is responsible for adequate packaging upon return to Spirit. Spirit is not responsible for damages in shipping. Make all freight damage claims
with the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER. All units arriving
without a return authorization number will be refused.
6. For any further information, or to contact our service department by mail, send your correspondence to:
Spirit Fitness, Inc.
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
Spirit Fitness, Inc. This warranty applies only in the 50 states of the U.S.A.
34
CR800_CU800
Download from Www.Somanuals.com. All Manuals Search And Download.
|