Spectra Laser Level GL612 User Manual

GL622/GL612  
User Guide  
Bedienungsanleitung  
Manuel de l´utilisateur  
Guida per l´uso  
Gúia del usuario  
Gebruikershandleiding  
Operatörshandbok  
Brugermanual  
Guia do Usuário  
Bruksanvisning  
Käyttäjän opas  
Instrukcja obsługi  
Trimble Spectra Precision Division  
5475 Kellenburger Road  
Dayton, Ohio 45424-1099, USA  
Руководство пользователя  
+1-937-245-5600 Phone  
©2012, Trimble Navigation Limited. All rights reserved.  
PN Q104848 Rev. D(05/13)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
GB  
Introduction  
2
FOR YOUR SAFETY  
2
COMPONENTS  
2
How to use the Laser System  
Powering the Laser  
3
3
RC602 Radio Remote Control  
Turning On/Off the RC602  
LASER SETUP  
3
3
4
Turning On/Off the Laser  
Features and functions  
Standard Features  
4
4
5
X-Y-grade entering mode  
Using the Rotation mode  
Manual mode  
5
6
6
Special MENU Features  
Menu Functions (Radio controlled)  
Automatic PlaneLok mode  
Automatic Grade Match  
Automatic Axis Alignment (only GL622)  
Activating/Deactivating Standby mode  
Start Reference Check  
Setting Menu  
7
7
8
9
10  
10  
10  
10  
11  
11  
12  
12  
12  
12  
13  
13  
13  
14  
14  
14  
14  
15  
15  
15  
15  
16  
16  
16  
16  
17  
18  
18  
18  
18  
19  
20  
Info  
Service menu  
Special Features - Vertical Setup  
Line Scan  
Setting menu details  
Pairing  
Pairing the transmitter with remote control  
Pairing the transmitter with receiver  
Mask mode  
Grade Entry  
Grade Display  
Sensitivity  
HI-alert selection  
User Name  
Set Password  
Password On/Off  
Radio (RF-Channel)  
Select Language  
CALIBRATION  
Checking Calibration of the Y- and X-Axes  
Checking Calibration of the Z-(vertical) Axis  
Troubleshooting  
PROTECTING THE UNIT  
CLEANING AND MAINTENANCE  
PROTECTING THE ENVIRONMENT  
WARRANTY  
TECHNICAL DATA  
ELECTROMAGNETICAL COMPATIBILITY  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Thank you for choosing one of the Spectra Precision Lasers from the Trimble family of precision lasers.  
The grade laser is an easy-to-use tool that offers accurate horizontal, vertical and sloped laser reference up  
to 1300 ft (400 m) away using a receiver.  
For Your Safety  
For hazardless and safe operation, read all the user guide instructions.  
• Use of this product by people other than those trained on this product may result in exposure to hazardous  
laser light.  
• Do not remove warning labels from the unit.  
• The GL622/GL612 is a class 2 laser (<3,4mW) IEC 60825-1:2007)  
• Never look into the laser beam or direct it to the eyes of other people.  
• Always operate the unit in a way that prevents the beam from getting into people‘s eyes.  
• If initial service is required, which results in the removal of the outer protective cover, removal must only be  
performed by factory-trained personnel.  
Caution: Use of other than the described user and calibration tools or other procedures may result  
in exposure to hazardous laser light.  
Caution: Using different than described at the GL6X2 user guide, may result in unsafe operation.  
COMPONENTS  
a
b
c
d
e
f
g
h
i
Keypad/LCD-Display  
Handle  
Rotor  
Sunshade  
Axes-Alignment-Marks  
Sighting Guides/Scope Mounts  
Battery door  
Rubber Cover/Recharge Jack  
5/8” x 11 Tripod Mounts  
Rubber Feet  
j
k
l
Turnable Legs  
Plus and Minus Battery Diagrams  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO USE THE LASER SYSTEM  
POWERING THE LASER  
Batteries  
WARNING  
Ni-MH batteries may contain small amounts of harmful substances. Be sure to charge the battery  
before using it for the first time, and after not using it for an extended length of time. Charge only with  
specified chargers according to device manufacturer‘s instructions. Do not open the battery, dispose  
of in fire or short circuit; it may ignite, explode, leak or get hot causing personal injury. Dispose in  
accordance with all applicable federal, state, and local regulations. Keep the battery away from  
children. If swallowed, do not induce vomiting. Seek medical attention immediately  
Recharging the Batteries  
The laser is shipped with a rechargeable Ni-MH battery pack.  
Note: The approximate charge of the batteries is shown at the left top side of the LCD.  
The charger requires approx. 10 hours to charge empty rechargeable batteries.  
For charging, connect the plug of the charger to the recharge jack of the battery pack.  
New or long-time out-of-use rechargeable batteries reach their best performance after  
being charged and recharged five times. For Indoor applications the charger can be  
used as a power supply for the GL.  
Alkaline batteries can be used as a backup. Insert 4 D-cell batteries noting the plus  
(+) and minus (-) diagrams inside the battery housing.  
The batteries should only be charged when the laser is between 50° F and 104° F (10°C to  
40°C). Charging at a higher temperature may damage the batteries. Charging at a lower  
temperature may increase the charge time and decrease the charge capacity, resulting in  
loss of performance and shortened life expectancy.  
RC602 Radio Remote Control  
Powering the RC602  
1. Open the battery door using a coin or similar pry device to release the  
battery door tab on the RC602. RC602 will be shipped with alkaline  
batteries Rechargeable batteries can be used optional but need to  
be charged externally  
2. Insert two AA batteries noting the plus (+) and minus (-) diagrams  
inside the battery housing.  
3. Close the battery door. Push down until it “clicks” into the locked  
position.  
Turning On/Off the Radio Remote Control  
The radio remote control is a hand-held device that allows you to send operational commands to the laser  
from a remote location.  
Press the power button to turn on the radio remote control. A “ ” and additional vertical bars appear in the  
right corner of the remote’s top display line indicating the radio connection status between the laser and the  
remote control.  
Note: When the remote control is initially turned on, the standard display (model number and software version)  
appear for the first 3 seconds, then the axes symbols and last-entered grade for each axis briefly appear in  
the LCD.  
With every button press, the LCD backlight is activated and turns off automatically if no button is pressed for  
8 seconds.  
To turn off the radio remote control, press and release the power button.  
Note: 5 minutes after the last button press, the remote control turns off automatically.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
LASER SETUP  
Position the laser horizontally (tripod mount and rubber feet downward!) on a stable platform, wall mount or  
tripod at the desired elevation.  
The laser recognizes automatically whether it is used horizontally or vertically when switched on.  
Turning On/Off the laser  
Press the power button to turn On/Off the laser.  
Note: Depending on the setup (horizontal or vertical) and if a grade value has been dialed in, the unit starts  
the temperature/reference check while the thermometer symbol is flashing.  
When the temperature/reference check has been finished, the standard display appears and the bubble symbols  
flash until self-leveling has been completed.  
If the self-leveling can’t be finished based on the selected sensitivity, an error message appears.  
Features and Functions  
Standard Display  
The remote control mirrors the functionality of the GL keypad  
Battery status laser  
Mask selection  
HI alert function is activated  
Battery Status Remote Control  
Rotation speed  
Status Radio Connectivity  
Button 1: Quickly press and release starts the  
MENU entry.  
Button 2: Quickly press and release starts the  
grade entering mode.  
Button 3: Quickly press and release activates/  
deactivates the manual mode.  
Button 4: Quickly press and release to toggle  
through the pre-selected rotation  
speeds.  
Button 5, 8: up/down arrow buttons.  
Button 6, 7: left/right arrow buttons.  
Button 9: ON/OFF button - press for 1 second to  
turn on the unit; press and hold for 2  
seconds to turn off the unit.  
Leveling/Standby – LED (green/red)  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Standard Features  
X-Y-grade entering – Step and Go mode  
Quickly press and release button 2 starts the grade entering mode. Both grade values will be shown.  
Press/release button 1 a grade reverse Y  
Press/release button 2 a grade reverse X (only GL622)  
Press/release button 3 a return to the standard display  
Quickly press and release button 4 to confirm the selected grade value and  
return to the standard display  
Press and hold button 6 or 7 (left/right) to change X- axis grade value (only GL622) after the comma; press  
and hold buttons 6 + 7 simultaneously starts X-axis quick change mode where the grade value in front of the  
comma will be set to 0% and then starts changing in 1% increments.  
Press and hold button 5 or 8 (up/down) for changing Y -axis grade value; press and hold buttons 5 + 8  
simultaneously starts Y - axis quick change mode where the grade value in front of the comma will be set to  
0% and then starts changing in 1% increments.  
Note: The speed of the grade value change increases with the amount of time the button is held down.  
Note: The grade value for both axes increases in 1.00% increments. When the grade value for either axis  
reaches its highest amount, the grade value switches to the lowest value for that axis. For example, the value  
switches from +25% to -25%.  
The laser will self-level to the required grade position after confirming the grade change with button 4.  
Note: The bubble symbols at the laser’s LCD will flash until the laser has been self-leveled to the requested  
grade position.  
X-Y-grade entering – Digit Select mode (Default)  
Quickly press and release button 2 starts the grade entering mode. .  
Both grade values will be shown.  
Press/release button 1 a quick set to 0%  
Press/release button 2 a change the sign in front of the grade value  
Press/release button 3 a return to the standard display.  
Quickly press and release button 4 to confirm the selected grade value and return to the standard display.  
Press and release button 5 or 8 (down or up) to move the cursor to the X- (only GL622) or Y-axis  
Pressing and releasing button 6 or 7 (right or left) moves the cursor to the right/left.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use button 1 or 2 (Plus or Minus) to set the desired digit.  
The laser will self-level to the required grade position after confirming the grade change with button 4.  
Note: The bubble symbols at the laser’s LCD will flash until the laser has been self-leveled to the requested  
grade position.  
Using the Rotation mode  
Repeatedly pressing the button 4 toggles through 300, 600, 900 rpm regardless if the unit is in  
automatic or manual mode.  
Manual mode  
Pressing and releasing button 3 at the Standard Display activates/deactivates  
the manual mode regardless if set up horizontal or vertical.  
Manual mode is indicated by horizontal lines next to the axes symbols.  
In Manual mode (horizontal), the Y-axis can be sloped by pressing the Up-(5) and Down-Arrow-(8) buttons on  
the laser‘s keypad or the remote control. Additionally, the X-axis can be sloped by pressing the Left-(6) and  
Right-(7) Arrow-buttons on the laser or remote control.  
In vertical mode, the up and down arrow buttons adjust the Z-axis slope, and the left and right arrow buttons  
align the laser beam to the right/left side.  
To resume automatic self-leveling mode, press the manual button again.  
Special MENU Features  
Menu Functions (Radio controlled)  
Press and release button 1 at the Standard Display to enter the MENU.  
The menu offers always only the features which can be selected depending on the setup (horizontal  
or vertical).  
The icon of the selected function will be highlighted.  
A down arrow at the the right site indicates that the user can scroll down through the menu using the  
button 8 (down arrow).  
After going to the next menu row, an up/down arrow at the the right site indicates that the user can scroll up/  
down through the menu (4 different screens) using the buttons 5/8 (up/down arrows).  
Pressing and releasing button 3 changes the unit always back to the standard or previous display.  
Press and release the buttons 6/7 until the desired icon at the selected menu row is highlighted.  
Press and release button 4 to open the submenu OR start the selected function.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu functions when set up horizontal  
Menu functions when set up vertical  
Note: Pairing function is needed to pair an already paired remote with a new transmitter.  
The new transmitter has to be set to the pairing dialog for this operation. Otherwise the pairing can not be  
successful processed.  
The pairing information of the previous pairing is still stored in the previous paired transmitter and should be  
deleted in the pairing dialog of this transmitter  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatic PlaneLok mode  
The PlaneLok mode can be activated in horizontal and vertical  
automatic and manual mode.  
In PlaneLok mode when set up horizontal, the beam will be locked  
to a fixed elevation point (up to 80 m (260 ft) located on one axis  
at each side of the laser.  
For keeping vertical alignments fixed to a direction point, PlaneLok  
can be used in both directions on the X-axis.  
1. Set up the laser over the reference point.  
2. Attach the HL750 receiver to a grade rod. Place the receiver  
at the second point and adjust it to the On-grade position. The receiver should be permanently mounted at  
this location and at the desired elevation.  
3. Use the sighting guides on the top of the laser to align the laser to the receiver. Turn the laser on the tripod  
until it is roughly aligned to the receiver’s position (the alignment range for both axes is +/-40°).  
4. Press and release the MENU button at the Standard Display and select PlaneLok.  
In vertical mode, PlaneLok can be started immediately by pressing button 4.  
Horizontal setup  
Vertical setup  
5. When set up horizontally, press and release button 4 to open the PlaneLok submenu; select the desired  
PlaneLok axis (X- only GL622) then press button 4 to start PlaneLok.  
Note: The laser starts to search for the receiver. A flashing Receiver and Lock symbol appears at the selected  
axis and becomes solid when PlaneLok has been completed.  
mm  
Note: When used in vertical mode, the receiver has to be placed  
with the photocell on the bottom side.  
The HL750 display shows a flashing –PL– during the time the  
laser is searching and adjusting the beam to the on-grade position.  
When PlaneLok is complete, –PL– stops flashing at the HL750  
display.  
Note: The laser continues to servo to the receiver’s signals.  
6. Exiting of PlaneLok can be done by pressing button 3 (ESC).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatic Grade Match  
The Grade Match mode can be activated in horizontal automatic and  
manual mode.  
In Grade Match mode, the laser can be used to measure the existing  
grade value between two known elevation points (up to 80 m (260 ft)  
located on one axis at each side of the laser  
1. Set up the laser over the reference point.  
2. Attach the HL750 receiver to a grade rod. Check the laser’s elevation next to the laser then position the  
receiver at the second point WITHOUT changing the receiver’s elevation on the rod.  
3. Use the sighting guides on the top of the laser to align the laser to the receiver. Turn the laser on the tripod  
until it is roughly aligned to the receiver’s position (the alignment range for both axes is +/-40°).  
4. Press and release the MENU button at the Standard Display and select Grade Match.  
5. Select the desired Grade Match axis (X- only GL622) then press button 4 to start Grade Match.  
Note: The laser starts to search for the receiver. A flashing Receiver and angle  
mm  
symbol appears at the selected axis and disappears when Grade Match has  
been completed.  
While the laser is searching and adjusting the beam to the on-grade position, the  
HL750 display shows a flashing –GM–.  
When Grade Match has been completed, the HL750 goes back to the standard  
elevation display. The remote control as well as the laser will display the final  
measured grade value.  
Note: If Grade match can’t be completed by checking the limits, the laser comes  
with an Error message (Grade Match has Failed) which can be deleted with button 4 (OK). The HL750 goes  
back to standard elevation indication.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatic Axis Alignment (only GL622)  
Automatic Axis Alignment mode adjusts automatically the direction  
the grade axis is pointing to the receiver’s location by an electronically  
simulation of rotating the unit on its base to match the hub. Using Axis  
Alignment, the laser axis can be aligned to one direction hub (up to 80 m  
(260 ft) located on one axis at each side of the laser.  
1. Set up the laser over the reference point.  
2. Place the grade rod with the attached HL750 receiver at the desired  
direction hub.  
3. Use the sighting guides on the top of the laser to align the laser to the receiver. Turn the laser on the tripod  
until it is roughly aligned to the receiver’s position (the alignment range for both axes is +/-40°).  
4. Press and release the MENU button at the Standard Display and select Axis Align.  
5. Select the desired axis then press button 4 to start Axis Align.  
Note: Adjusting the receiver into the beam before starting the automatic Axis Alignment reduces the time  
needed for finishing the alignment.  
Activating/Deactivating Standby mode  
Press and release the MENU button at the Standard Display and select Standby.  
Pressing and releasing button 4 activates the Standby mode.  
The self-leveling will be stopped and the beam will be turned off while the HI alert is still active.  
The display shows the standby symbol and the Level/Standby LED flashes red every 5 seconds.  
To deactivate Standby mode and restore full operation of the laser, press and release button 4.  
Start Reference Check  
Before starting some grade work which is very sensitive an additional Reference Check can  
be started manually. Press and release the MENU button at the Standard Display and select  
Reference Check.  
Pressing and releasing button 4 starts the Reference Check considering the current temperature  
inside the housing. While the rotor checks the correct position the rotation will be stopped.  
Setting Menu  
Press and release the MENU button at the Standard Display and select Settings.  
Press and release button 4 to open the Setting Menu; select the desired function then press button  
4 to open the selected submenu function OR start the selected function.  
Please see the Setting Menu details at the end of the user guide.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Info  
Press and release the MENU button at the Standard Display and select Info.  
Buttons 6/7 can be used to toggle between GL, RC and Runtime.  
Press and release button 4 to confirm the selection.  
The GL/RC information (software version, ID, etc.) or the runtime of the GL will be displayed.  
Service  
Press and release the MENU button at the Standard Display and select Service. Buttons 6/7 can be  
used to toggle between Calibration Y and Calibration X OR Calibration Z when set up vertically.  
Press and release button 4 to confirm the selection. The calibration at the selected axis starts the field  
calibration procedure.  
The RC602 Service menu offers one additional feature:  
RF Connectivity  
Press and release button 4 to get a status of the current Radio connectivity.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special Features - Vertical Setup  
Line Scan  
Line Scan centers the rotor horizontally and can be used to align the plumb beam to a desired  
horizontal position. Press and release the MENU button at the Standard Display and select Line  
Scan. Pressing and releasing button 4 activates the Line Scan mode while the rotor checks the  
limits of the X- axis and stops at the center position.  
Pressing button 3 (ESC) stops the movement and changes the unit into manual mode.  
Corrections up and down can be done using button 5/8; for left/right corrections use button 6/7.  
Press and release the manual button to change the unit back to full automatic mode.  
Setting Menu  
Press and release the MENU button at the Standard Display and select Settings.  
Press and release button 4 to open the Setting Menu; select the desired function then press button  
4 to open the selected submenu function OR start the selected function.  
The Setting Menu offers the following functions:  
Pairing  
HI-Alert  
Mask Mode  
Grade Entry  
Grade Display  
Sensitivity  
User Name  
Set Password Password On/Off RF-Channel  
Select  
Language  
Pairing  
When in Settings, press and release button 4 to open the Pairing menu. The display shows the  
currently paired units (up to two receivers and two remote controls). If already 2 remote controls  
have been paired, one of them has to be deleted using button 1 (CLR).Turn on the RC602 and  
select the Pairing menu and press button 4.  
The GL6X2 pairs now automatically with the new remote control.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pairing the transmitter with remote control  
The chain symbol at button 1 indicates the remote has never been paired before which means no radio  
connectivity is given. Pressing the pairing button 1 will initiate a pairing request. The transmitter has to be in  
pairing mode as shown above.  
Note: Make sure that pairing mode is selected only at one transmitter which is within the radio range of the  
remote during a pairing request. Otherwise pairing procedure can be confused.  
Pairing the transmitter with receiver  
To pair the transmitter and the receiver select Settings and press and release button 4 to open the Pairing  
menu. The display shows the currently paired units (up to 2 receivers). If already 2 receivers have been paired,  
one or both of them have to be deleted using button 1 (CLR).  
A
C
B
Next, turn on the receiver then press and hold the Deadband (A) and the Audio (B) buttons for two seconds.  
After two seconds the display shows MENU first, then RDIO.  
Press and release the Units (C) button – display shows the current radio mode.  
If not already set to LS, press Units button and then press Deadband or Audio button until LS is displayed.  
Press Units button again to enter selection. Press and release the Audio button – display shows PAIR. Press  
the Units button again – the display shows PAIR and a rotating bar. After completing PAIR, OK will be displayed.  
The GL6X2 pairs now automatically with the new receiver. Press and release the Power button two times to  
exit the menu. A laser symbol is lit to confirm the receiver can communicate with the laser.  
Mask mode  
Select the Mask icon and press and release button 4 to open the Mask setting menu. Depending  
on which side or corner the beam should be turned off, the required sector can be selected. Press  
and release the buttons 5 to 8 for moving a short flashing line around the mask mode symbol. For  
selecting the sector where the bar is flashing, press and release button 1 (SET). After setting the  
first sector, button 1 changes to show CLR which offeres the capability of deleting the selected mask  
sector again. Use button 5 to 8 to move the flashing bar to other required areas and repeat the setting process.  
When all areas have been set, press button 4 to store the mask sector selection until the unit will be turned off.  
Hinweis: The unit always powers up with the mask mode deactivated (default).  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Grade Entry  
Select the Grade Entry icon and press and release button 4 to open the Grade Entry menu.  
Buttons 6/7 can be used to toggle between Step and Go and Digit Select.  
Press and release button 4 to confirm the selection.  
Step and Go  
Digit Select  
Grade Display  
Select the Grade Display icon and press and release button 4 to open the Grade Display menu.  
The desired Grade Display Mode (Percent/ Permille/Degree) can be selected using the buttons 6/7.  
Press and release button 4 to confirm the selected display mode.  
Sensitivity Selection  
Select the Sensitivity icon and press and release button 4 to open the Sensitivity menu. The  
desired Sensitivity: Low, Mid (Default) and High) can be selected using the buttons 6/7. Press  
and release button 4 to confirm the selected Sensitivity.  
HI-alert Selection  
Select the HI icon and press and release button 4 to open the HI-alert menu. The desired HI-alert:  
5 min.(Default), 30 seconds and HI-Off) can be selected using the buttons 6/7. Press and release  
button 4 to confirm the selected HI-alert.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Name  
Select the User name icon and press and release button 4 to open the User name menu. One  
row for typing names in big font (15) and one row in small font (18) for letters or numbers are  
available. Button 5 and 8 can be used to toggle between both rows. Changing the characters  
can be done using the buttons 1 and 2. Press and release button 4 to confirm the selected user  
name. The display falls back to the main menu. Any time the unit will be powered up, the User  
info will be displayed for couple seconds.  
Set Password  
Select the Set Password icon and press and release button 4 to open the Password menu. Use  
Button 1 to 8 to type in a password containing of 4 digits and repeat the password at the second  
row. Press and release button 4 to store the selected password; unit falls back to the standard  
menu. After powering up the unit, the standard display comes up if the correct password will be  
entered, otherwise the unit turns off automatically.  
Password On/Off  
Select the Set Password ON-Off icon and press and release button 4 to open the Password menu.  
Buttons 6/7 can be used to toggle between Password On and Password Off if a Password has  
been entered before. Press and release button 4 to confirm the selection.  
Password on  
Password off  
Radio (RF) Channel  
Select the RF Channel icon and press and release button 4 to open the Radio Channel menu.  
The desired RF Channel: Low, Mid (Default), and High can be selected using the buttons 6/7.  
Press and release button 4 to confirm the selected RF Channel. After changing the RF channel,  
the RC and HL needs to be paired again.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Select Language  
Select the Language icon and press and release button 4 to open the Language menu.Use button 5  
to 8 to select the required local language (EN, DE, IT, FR, ES, PT, NL, DA, NO, SV, FI, PL, TR, CZ).  
Press and release button 4 to store the selected Language; unit falls back to the standard menu.  
CALIBRATION  
Checking Calibration of the Y- and X-Axes  
1. Set up the laser 30 m (100 ft) from a wall and allow it to level.  
2. Set the grade to 0.000% in both axes.  
3. Raise/lower the receiver until you get an on-grade reading for the +Y axis. Using  
the on-grade marking notch as a reference, make a mark on the wall.  
Note: For increased precision, use the fine-sensitivity setting (1.5 mm/ 1/16 in.) on  
the receiver.  
4. Rotate the laser 180° (-Y axis toward the wall) and allow the laser to re-level.  
5. Raise/lower the receiver until you get an on-grade reading for the –Y/axis. Using the  
on-grade marking notch as a reference, make a mark on the wall.  
6. Measure the difference between the two marks. If they differ more than 3 mm at 30  
m (1/8 inch at 100 feet), the laser needs calibrating.  
7. After checking the Y-axis, rotate the laser 90°. Repeat the above starting with the  
+ X axis facing the wall.  
Checking Calibration of the Z-(vertical) Axis  
To check vertical calibration, you need a plumb bob with at least 10m (30ft) of string.  
1. Suspend the plumb bob in front of a house i.e., attached to a window frame whose window height is at least  
10m (30ft).  
2. Set up the laser in vertical so that the laser beam strikes the receiver’s on-grade position at the top of the string.  
3. Look for any deviation using the receiver from the top of the string to the bottom of it. If the deviation is more  
than 1mm (<1/16 in.), the vertical axis needs calibrating.  
Note: If calibration is required, please, refer to the calibration instructions on our Trimble website  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Any error message can be deleted with a short press of button 4 (OK). The table shows the related description  
and possible solutions. The next service center should be contacted if a different error message as shown at  
the table will be displayed.  
Error codes  
Description  
Solution  
21  
Temporary EEprom problem  
Repeat pairing and re-enter the  
customer settings  
120  
HI alert - Unit Heigt changed  
Check laser beam elevation after  
deleting the HI alert  
130  
Mechanical Limit during Axis  
Alignment, Grade Match or Spot  
Match  
Re-align the closer to the  
alignment point; check if existing  
slope is above +/-25%  
131  
140  
Rake Angle Limit  
Re-align the unit closer to the  
alignment point  
Laser beam blocked  
Make sure there are no  
obstacles between the  
transmitter and the HL750  
141  
150  
152  
153  
160  
Time Out - Function could not be Check radio operating range/  
completed in the allowed time  
connection; check stable laser  
setup  
No receiver - Receiver not  
available for single axis  
automatic function  
Make sure the receiver is on and  
paired  
No receiver - The laser searched Check the operating range for  
for the receiver but could not  
find it  
auto function and restart the auto  
alignment  
Lost Receiver - The laser  
searched and found the receiver  
but then lost it  
Check the operating range for  
auto function and restart the auto  
alignment  
X or Y level sensor defect  
Contact service center  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROTECTING THE UNIT  
Do not expose the unit to extreme temperatures or temperature changes (do not leave inside the car). The  
unit is very robust and can resist damage if dropped even from tripod height. Before continuing your work,  
always check the leveling accuracy. See Checking Calibration section. The laser is water proof and can be  
used indoors and outdoors.  
CLEANING AND MAINTENANCE  
Dirt and water on the glass parts of laser or prism will influence beam quality and operating range considerably.  
Clean with cotton swabs. Remove dirt on the housing with a lint-free, warm, wet and smooth cloth. Do not use  
harsh cleansers or solvents. Allow the unit to air dry after cleaning it.  
PROTECTING THE ENVIRONMENT  
The unit, accessories and packaging ought to be recycled. This manual is made of non-chlorine recycling  
paper. All plastic parts are marked for recycling according to material type.  
Do not throw used batteries into the garbage, water or fire. Remove them in compliance with  
environmental requirements.Hinweis für Kunden in der EU  
Notice to Our European Union Customers  
For product recycling instructions and more information, please go to:  
Recycling in Europe: To recycle Trimble WEEE,  
Call +31 497 53 2430, and ask for the “WEEE Associate”  
or  
Mail a request for recycling instructions to:  
Trimble Europe BV  
c/o Menlo Worldwide Logistics  
Meerheide 45  
5521 DZ Eersel, NL  
Warranty  
Trimble warrants the GL622/GL612 to be free of defects in material and workmanship for a period of 5 years.  
Trimble or its authorized service center will repair or replace, at its option, any defective part, or the entire  
product, for which notice has been given during the warranty period. If required, travel and per diem expenses  
to and from the place where repairs are made will be charged to the customer at the prevailing rates. Customers  
should send the product to Trimble Navigation Ltd. or the nearest authorized service center for warranty  
repairs or exchange, freight prepaid. Any evidence of negligent, abnormal use, accident, or any attempt to  
repair the product by other than factory-authorized personnel using Trimble certified or recommended parts,  
automatically voids the warranty. Special precautions have been taken to ensure the calibration of the laser;  
however, calibration is not covered by this warranty. Maintenance of the calibration is the responsibility of  
the user. The foregoing states the entire liability of Trimble regarding the purchase and use of its equipment.  
Trimble will not be held responsible for any consequential loss or damage of any kind. This warranty is in lieu  
of all other warranties, except as set forth above, including any implied warranty merchantability of fitness for  
a particular purpose, are hereby disclaimed.  
This warranty is in lieu of all other warranties, expressed or implied.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL DATA  
GL622/GL612  
Leveling accuracy1,3  
:
± 0.5 mm/10 m, 1/16“ @ 100 ft, 10 arc seconds  
± 1.0 mm/10 m, 1/8“ @ 100 ft, 20 arc seconds  
300, 600, 900 rpm  
appr. 400 m (1300 feet) radius with detector  
red diode laser 650 nm  
Grade accuracy1,3  
Rotation:  
:
Operational area1,2  
Laser type:  
:
Laser class:  
class 2, <3.2 mW  
Self-leveling range:  
appr. ± 14°  
Grade range (Y, X-GL622):  
Leveling indicators:  
Radio range (HL750):  
Power source:  
± 25% both axes (not simultaneously)  
LCD indications and LED flashes  
up to 80 m (260 ft)  
NiMH battery pack  
Battery life1:  
35 hours NiMH; 40 hours alkaline  
-20°C to 50°C (-4°F to 122°F)  
-20°C to 70°C (-4°F to 158°F)  
5/8 x 11 horizontally and vertically  
IP67  
Operating temp.:  
Storage temp.:  
Tripod attachments:  
Dust and Water proof:  
Weight:  
3.1 kg (6.8 lbs)  
Low voltage indication:  
Low voltage disconnection:  
LCD battery indicator  
unit shuts off  
1) at 21°Celsius  
2) under optimal atmospheric circumstances  
3) along the axis  
Remote Control RC602  
Radio Operating range1,3  
Power source:  
:
up to 100 m (330 ft)  
2 x 1.5V AA alkaline batteries  
130 hours  
Battery life1:  
Dust and Water proof:  
Weight:  
IP66  
0.26 kg (0.4 lbs)  
DECLARATION OF CONFORMITY  
Please disregard the declaration of conformity within the manual.  
Following is the valid declaration:  
We  
Trimble Kaiserslautern GmbH  
Declare under our sole responsibility that the products  
GL622/GL612 and RC602  
To which this declaration relates is in conformity with the following standards:  
EN 50371:2002, EN 60825-1:2007, ETSI EN 300328 V1.7.1:2006, ETSI EN 301489-1 V1.9.2:2011,  
ETSI EN 301489-3 V1.4.1:2002  
following the provisions of directive R&TTE 1999/5/EC.  
The managing director  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRO-MAGNETIC COMPATIBILITY  
Compliance statement (part 15.19) This device complies with part 15 of the FCC Rules and Industry Canada  
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation. Warning (part 15.21) Changes or modifications not  
expressly approved by the party responsible for compliance could void the user’s authority to operate the  
equipment. This in particular is applicable for the antenna which has been delivered with the GL622/GL612  
and RC602 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of  
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential  
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent  
isotropically radiated power (e.i.r.p.) is not more than that necessary for succesful communication.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Singer Sewing Machine 99 31 User Manual
Singer Sewing Machine 107 1 User Manual
Sony Car Stereo System CDX 838 User Manual
Sony Cordless Telephone SPP N1000 User Manual
Sony Satellite Radio AIR SA17TI User Manual
SpeakerCraft Speaker AIM LCR3 User Manual
Subaru Automobile 25 XS LLBEAN User Manual
Sylvania Portable DVD Player SDVD7045 User Manual
Sylvania TV DVD Combo CD202SL8 User Manual
Tapco Stereo Amplifier CP500 User Manual