OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction.........................................................................
Post Setup..........................................................................
Frame Features...................................................................
Air Pressure Chart (Enduro).................................................
Frame Geometry(Enduro)....................................................
Schematic and Specifications (Enduro)..............................
Frame Geometry (SX)..........................................................
Schematic and Specifications (SX).....................................
Warranty...............................................................................
4
6
8
9
10
12
14
16
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase and welcome to the finest line of suspension bikes available!
About this Manual
This manual is designed to be used in conjunction with the Bicycle Owner’s Manual and owner’s manuals supplied by the manufacturer of the front and rear suspension components. If you did not
receive any of these manuals, download them from the Internet, contact your dealer, or contact us by telephone. There may be more current manuals and technical information available. For the most
current information , regularly check the Specialized web site or consult your Specialized dealer. These manuals were written for an important reason: your safety while riding.
This manual contains many “Warnings” and “Cautions” concerning the consequences of failure to maintain or inspect your bicycle or of failure to follow safe cycling practices. The combination of
the safety alert symbol and the word Warning indicates a potentially hazardous situation which, if not avoided, could result in serious injury or death. The combination of the safety alert symbol and
the word Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or damage to your bicycle or a component. Because the consequences of
not following a Warning usually include “you may lose control and fall,” which could result in serious personal injury or death, we may not repeat this in conjunction with each Warning. Because it is
impossible to anticipate every situation or condition which may occur, a practice or situation may be unsafe but not anticipated by this manual. So, don’t forget to use your common sense.
Warning: Make sure you have, review, and understand the warnings, instructions, and content of the manuals for your bicycle.
About Off Road, Stunt, Downhill and Freeriding
Downhill racing, severe off road riding, jumping, and stunt riding is extremely dangerous. Some downhill racers and freeriders reach speeds similar to motorcycles, thus face similar risks and hazards.
When engaging in these activities, you, your bicycle and safety equipment must be in perfect condition. We recommend that at all times you wear appropriate safety gear, such as an approved full
face helmet, full finger gloves, and body armor.
Not every bicycle is built for every activity. Check with your Specialized dealer to make sure you have the right equipment.
No bicycle is indestructible. Downhill racing, severe off road riding, jumping, and stunt riding increases the stress on every part of your bicycle. Frames or parts under high stress may fail, causing you
to lose control or fall. Because of the risk involved, Specialized recommends that you conduct a thorough inspection before each ride. If you miss a jump, ditch your bike in mid crash, dump or launch
your bike without you on it, inspect yourself for injury, then carefully inspect your bicycle for damage.
Here is what you should look for when you inspect your bicycle for this type of riding: bent or broken components, such as the handlebar, handlebar stem, seatpost, pedals; dents, cracks, scratches,
deformation, or discoloration. Because damage may be internal and hidden, if any of these signs are present, stop riding until your bicycle has been thoroughly inspected by your Specialized dealer.
Warning: Although many catalogs, advertisements and articles about bicycling depict riders racing, jumping, riding hard off road, and/or
stunt riding, this activity is extremely dangerous, increases the rider’s risk of injury or death, and potentially increases the severity of
any injury. The action depicted is being performed by experts with many years of training and experience. Even with that training and
experience, cyclists who engage in such activity often get seriously injured. It is also foreseeable that some jumps or stunts, and even
during some races, that the rider will exceed the design capacity of the frame or components, which may result in something on the bicycle
bending or breaking. If a frame or component bends or breaks, such may lead to loss of control, serious personal injury or death.
!
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
As activities such as racing, jumping, severe off road riding, and stunt riding are extremely dangerous, SAFETY should always be the first consideration. Don’t ride in the race, ride hard off road, try the
jump, or do the stunt, UNLESS YOU CAN DO SO SAFELY. Here are some additional recommendations:
• Take lessons from a competent instructor first.
• Do jumps or stunts only in areas designated for this type of riding.
• Start with easy jumps and easy stunts first, and slowly develop skills before trying more dangerous jumps or stunts.
• Wear appropriate safety gear, such as a full face helmet, body armor, full finger gloves.
• Make sure by checking with your dealer that your bike is suitable for the kind of activity you intend to engage in.
• Constantly inspect your bicycle for signs of stress: cracks in the paint; dents; crushing or bending of the frame; bent components. Do not ride your bicycle if it shows such
signs of stress.
• Do not seek to bend or break the frame or components. Remember, SAFETY FIRST!!!
• Understand and recognize that the stresses imposed on your bike by riding at speed, jumping or stunt riding may break or damage parts of the bicycle, which may result in
loss of control, serious injury or death.
Specialized does not warrant the bicycle frame or components for such activities, and expressly disclaims all warranties, including the warranty of fitness for particular purpose and merchantability.
Stunt riding, severe off road riding, jumping, or riding downhill at speed is extremely dangerous, and the rider voluntarily assumes the risk that the bicycle frame and/or its components will bend or
break, and voluntarily assumes the risk of injury or death.
Service and Modifications
Technological advances have made bicycles and bicycle components more complex, and the pace of innovation is increasing. It is impossible for this manual or the accompanying manuals to provide
all the information required to properly repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work performed by an authorized Specialized
retailer.
Warning: Service on Specialized bicycles requires special knowledge and tools. Specialized recommends that all service and
repairs be performed by an authorized Specialized retailer.
!
Your bicycle has been engineered and tested with specific components and parts. Because of the great variety in these items, it is impossible for Specialized to test and approve of
all possible combinations. Modifying the frame, fork, or any of the components may make your bike unsafe. For example, changing the front suspension on your bicycle may alter
the steering characteristics and/or add stresses to the frame which have not been tested for. If you must replace any component, have this done by your authorized Specialized
retailer.
Warning: Never modify your frame or bicycle in any way. Do not sand, drill, fill, or remove parts. Do not install incompatible
forks or suspension parts. An improperly modified frame, fork, or component, can cause you to lose control and fall.
!
!
Caution: Any modification of your frame, fork, or components means that your bike no longer meets our specifications and
therefore voids your warranty.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT POST SETUP
SEATPOST MINIMUM EXTENSION: All Specialized full suspension models with interrupted seat tubes have a small hole to identify the minimum extension allowed for your
seatpost. If you cannot see the seatpost tube through this hole, your seatpost is too far extended. If a greater saddle height is required, replace the seatpost with a longer one.
������� ���� ����
��������� ����� ����
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT POST SETUP
Warning: Read the following instructions on proper seat post adjustment before riding your Specialized Enduro. Failure to follow these instructions can
result in damage to the equipment and rider.
!
ENDURO MODELS
On 2002-2004 Enduro models, the interrupted seat tube design is NOT equipped with a seat post insertion limiting stop at the base of the seat tube which allows for a wide range
of adjustment for extension and insertion to accommodate certain types of terrain and riding styles.
SEATPOST MINIMUM INSERTION: The frame design allows the seat post to be lowered below the base of the seat tube. While this allows a wider range of adjustment, it also
makes the shock vulnerable to damage due to contact from the edge of the seat post if lowered too far. Avoiding contact between the seatpost and shock is also important to
achieve proper suspension function.
To help protect the rear shock from impact damage, a small rubber bumper is included. This bumper is to be placed on the shock body where it would intersect with the seatpost if
it were lowered to the shock. This will help to protect the shock from damage and maintain proper suspension function.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO FSR / SX FRAME FEATURES
1. Main Frame
2. Seatstay
3. Chainstay
4. Shock Link
5. Main Pivot
�
�
�
�
6. Dropout (Horst) Pivot
7. Shock Link at Seatstay Pivot
8. Shock Link at Frame Pivot
9. Lower Shock Eyelet
10. Upper Shock Eyelet
11. Shock
�
�
�
�
�
�
�
�
�
�
�
12. Replaceable Derailleur Hanger
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO FSR AIR PRESSURE CHART
Rider
Rider
Weight
Weight
Air PSI
lbs
(kg)
95-105
(43-47)
(47-52)
(52-57)
(57-61)
(61-66)
(66-70)
(70-75)
(75-80)
(80-84)
(84-89)
(89-93)
(93-102)
(102-111)
(111-120)
75
105-115
115-125
125-135
135-145
145-155
155-165
165-175
175-185
185-195
195-205
205-225
225-245
245-265
85
95
105
115
125
135
145
155
165
175
185
205
225
NOTE: This air chart is designed as a recommended starting point only. Please refer to your shock owner’s manual for additonal setup information.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO FSR FRAME SPECIFICATIONS
Small (mm)
551
Small (in)
21.7”
28.0”
3.94”
70.5º
Medium (mm) Medium (in)
Large (mm)
610
Large (in)
24.0”
29.0”
4.72”
70.5º
X-Large (mm) X-Large (in)
1
2
3
4
4
5
5
6
6
7
8
*Top Tube Length
**Standover Hgt
584
711
110
70.5º
69.5º
69º
23.0”
28.0”
4.33”
70.5º
69.5º
69º
638
737
140
70.5º
69.5º
69º
25.12”
29.0”
5.51”
70.5º
69.5º
69º
711
100
70.5º
69.5º
69º
737
120
70.5º
69.5º
69º
Head Tube Length
Head Tube Angle (Steep)
Head Tube Angle (Slack)
Seat Tube Angle (Steep)
Seat Tube Angle (Slack)
BB Height (High)
69.5º
69º
68º
13.23”
12.76”
42.01”
16.7”
69.5º
69º
68º
13.23”
12.76”
43.94”
16.7”
68º
336
68º
68º
68º
336
68º
68º
336
324
1091
424
13.23”
12.76”
42.95”
16.7”
336
324
1144
424
13.23”
12.76”
45.04”
16.7”
BB Height (Low)
324
324
Wheelbase
Chainstay Length
1067
424
1116
424
* TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube.
** Stand Over height is measured vertically at the centerpoint of the TT.
Headset: 1 1/8”
Seatpost diameter: 30.9mm
Front derailleur clamp: 34.9mm
Rear hub spacing: 135mm
BB shell: 68mm
Seat Collar: 34.9mm
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO FSR FRAME GEOMETRY
�
�
�
�
�
�
�
�
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematic #2
2.e
1.c
S
h
o
c
k
L
i
n
k
Mount
2.f
1.d
1.h
1.g
1.c
2.e
S
h
o
c
k
Link
1.h
1.
d
2.o
2.h
2.f
2
.n
2
.k
S
h
o
ck
Link
2
.m
NOTE:
Pa
r
t 2.m Necessar
y
for
limit d r
e
un of 2002 frames
o
n
ly
2.g
1.f
.b
.f
2.d
1
1
1.e
1.e
2.c
1.a
2
.b
1
.b
1
.a
Dropouts
1
.f
1.b
BB Shell
1.f
1.b
1.f
1.a
2.c
1.
a
1.e
1.e
2
.d
2.
a
2003-2004
E
nduro
M
odel
200
2
Enduro model
12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance
should be performed by your local Specialized dealer.
Bearing Kit Parts
Part # Qty.
Part Description
Part Specification
1.a
1.b
1.c
1.d
1.e
1.f
2
4
2
2
2
6
2
2
BB Pivot Bearing
Dropout Pivot Bearing
Shock Link @ Frame Pivot Bearing
Shock Link @ Seatstay Pivot Bearing
BB Pivot Spacer
Dropout Pivot Bearing Spacer
Shock Link @ Frame Pivot Spacer
Shock Link @ Seatstay Pivot Spacer
6902 RS Series Bearing - 28mm O.D. x 15mm I.D. x 7mm Width
688 Series Bearing - 16mm O.D. x 8mm I.D. x 5mm Width
6800-2RS Series Bearing - 19mm O.D. x 10mm I.D. x 5mm Width
6800-2RS Series Bearing - 19mm O.D. x 10mm I.D. x 5mm Width
Steel spacer - 20mm O.D. x 15mm I.D. x 4mm Width
Steel spacer - 13mm O.D. x 8mm I.D. x 1.5mm Width
Steel spacer - 16mm O.D. x 10mm I.D. x 2mm Width
Steel spacer - 16mm O.D. x 10mm I.D. x 2mm Width
1.g
1.h
Bolt Kit Parts
B = Blue Loctite required
Part # Qty.
Part Description
Part Specification
Torque in*lb
2.a
2.b
2.c
2.d
2.e
2.f
2.g
2.g
2.h
2.k
2.m
2.n
2.o
1
1
2
2
2
2
1
1
1
1
2
2
1
BB Pivot Axle
BB Pivot Nut
BB Pivot Bolt (02 Enduro only)
Black Alloy Axle - 15mm O.D. (27.5mm Head O.D.) x 68.5mm Length, 6mm Allen Hex Head
Alloy Nut - 27.5mm O.D x 15mm I.D, 19mm socket
200-230 B
200-230
180-200 B
70-90 B
120-140 B
120-140 B
90-110
Black Alloy Bolt - 15mm O.D. x 25mm Length (shoulder - 10mm, threads - 15mm)
Black Alloy Bolt - 8mm O.D. x 26mm Length (shoulder - 17mm, threads - 9mm)
Black Alloy Bolt - 10mm O.D. x 20mm Length (shoulder - 6mm, threads - 14mm)
Black Alloy Bolt - 10mm O.D. x 20mm Length (shoulder - 6mm, threads - 14mm)
Steel Bolt - M6 x 40mm, 5mm Allen Hex Head (Early production - 2002 model)
Steel Bolt - M6 x 45mm, 5mm Allen Hex Head (Late production - 2002 model to present)
Steel Bolt - M8 x 50mm, 6mm Allen Hex Head
Dropout Pivot Bolt
Shock Link @ Frame Pivot Bolt
Shock Link @ Seatstay Pivot Bolt
Upper Shock Eye Bolt
Upper Shock Eye Bolt
Lower Shock Eye Bolt
Upper Shock Eye Nut
90-110
180-200 B
M6 Nut, Threadlock
Upper Shock Eye Spacer (Limited run)
Upper Shock Eye Washer
Lower Shock Eye Washer
Alloy Spacer - 16mm O.D. x 6mm I.D. x 3mm Width (Middle production - 2002 model)
M6 Washer
M8 Washer
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO SX FRAME SPECIFICATIONS
Short (mm)
551
Short (in)
21.7”
28.0”
3.94”
69º
Long (mm)
584
Long (in)
23.0”
28.0”
4.33”
69º
1
2
3
4
4
5
5
6
6
7
*Top Tube Length
**Standover Hgt
711
711
Head Tube Length
100
110
Head Tube Angle (Steep)
Head Tube Angle (Slack)
Seat Tube Angle (Steep)
Seat Tube Angle (Slack)
BB Height (High)
69º
68º
67.5º
66.5º
318
69º
68º
67.5º
66.5º
318
68º
68º
67.5º
66.5º
12.5”
12.1”
16.7”
67.5º
66.5º
12.5”
12.1”
16.7”
BB Height (Low)
Chainstay Length
307
424
307
424
* TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube.
** Stand Over height is measured vertically at the centerpoint of the TT measurement.
Headset: 1 1/8”
NOTE: Using travel chips limits the stroke and travel of the shock. A shorter stroke/travel
requires a stiffer spring to compensate so that the shock doesn’t bottom out. The Enduro SX
comes stock with 2 travel chips, which provides 3.5” travel.
Seatpost diameter: 30.9mm
Front derailleur clamp: 34.9mm
Rear hub spacing: 135mm
BB shell: 68mm
Seat Collar: 34.9mm
Stroke (Short travel): 31.75mm (1.25”)*
Travel (Short): 3.5”
NOTE: Spring weights listed above are to be used as an adjustment starting point only. Rider
weight and riding style may require a different spring rate than the stock spring rate. Replace
the spring accordingly. Refer to your shock manufacturer’s manual for additional shock setup
information.
Stroke (Medium travel): 38.1mm (1.5”)*
Travel (Medium): 4.0”
2 travel chips: Stock spring.
Stroke (Long travel): 44.45mm (1.75”)*
Travel (Long): 4.5”
1 travel chip: Stock spring, or test with 50lb lighter spring if exceeding spring preload range.
0 travel chips: Test with 50 lb lighter spring.
Eye-To-Eye: 171.5mm (6.75”)
* Stroke can be changed by adding or removing “Travel Chips”
SIZE
Short
Long
SPRING RATE
650lb spring
750lb spring
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ENDURO SX FRAME GEOMETRY
�
�
�
�
�
�
�
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematic #7
Shock Link Mount
2.d
1.c
2.e
1.d
1.h
1.g
1.c
2.d
Shock Link
1.h
1.d
2.e
2.m
2.g
2.k
2.h
Shock Link
Upper Shock Mount
2.f
1.f
1.b
1.f
2.c
1.e
2.a
1.a
1.b
Dropouts
1.f
1.b
BB Shell
1.f
1.a
2.b
1.b
1.e
2
.c
1.f
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance
should be performed by your local Specialized dealer.
Bearing Kit Parts
Part # Qty.
Part Description
Part Specification
1.a
1.b
1.c
1.d
1.e
1.f
2
4
2
2
2
6
2
2
BB Pivot Bearing
Dropout Pivot Bearing
Shock Link @ Frame Pivot Bearing
Shock Link @ Seatstay Pivot Bearing
BB Pivot Spacer
Dropout Pivot Bearing Spacer
Shock Link @ Frame Pivot Spacer
Shock Link @ Seatstay Pivot Spacer
6902 RS Series Bearing - 28mm O.D. x 15mm I.D. x 7mm Width
688 Series Bearing - 16mm O.D. x 8mm I.D. x 5mm Width
6800-2RS Series Bearing - 19mm O.D. x 10mm I.D. x 5mm Width
6800-2RS Series Bearing - 19mm O.D. x 10mm I.D. x 5mm Width
Steel spacer - 20mm O.D. x 15mm I.D. x 4mm Width
Steel spacer - 13mm O.D. x 8mm I.D. x 1.5mm Width
Steel spacer - 16mm O.D. x 10mm I.D. x 2mm Width
Steel spacer - 16mm O.D. x 10mm I.D. x 2mm Width
1.g
1.h
Bolt Kit Parts
B = Blue Loctite required
Part # Qty.
Part Description
Part Specification
Torque in*lb
2.a
2.b
2.c
2.d
2.e
2.f
2.g
2.h
2.k
2.m
1
1
2
2
2
1
1
1
2
1
BB Pivot Nut
BB Pivot Axle
Dropout Pivot Bolt
Alloy Nut - 27.5mm O.D x 15mm I.D, 19mm socket
200-230
200-230 B
70-90 B
120-140 B
120-140 B
180-200
Chromoly Axle - 15mm O.D. (27.5mm Head O.D.) x 68.5mm Length, 6mm Allen Hex Head
Chromoly Bolt - 8mm O.D. x 26mm Length (shoulder - 17mm, threads - 9mm)
Chromoly Bolt - 10mm O.D. x 20mm Length (shoulder - 6mm, threads - 14mm)
Chromoly Bolt - 10mm O.D. x 20mm Length (shoulder - 6mm, threads - 14mm)
Steel Bolt - M8 x 50mm, 6mm Allen Hex (Round) Head
Steel Bolt - M8 x 50mm, 6mm Allen Hex (Square) Head
M8 Nut, Threadlock
Shock Link @ Frame Pivot Bolt
Shock Link @ Seatstay Pivot Bolt
Upper Shock Eye Bolt
Lower Shock Eye Bolt
Upper Shock Eye Nut
180-200 B
Upper Shock Eye Washer
Lower Shock Eye Washer
M8 Washer
M8 Washer
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SBC LIMITED WARRANTY
Specialized Bicycle Components, Inc. (“Specialized”), a California corporation located at 15130 Concord Circle, Morgan Hill, California 95037, makes the following Limited Warranty
concerning Specialized bicycles and framesets:
LIMITED LIFETIME WARRANTY ON BICYCLE FRAMES AND FRAMESETS
Subject to the following limitations, terms and conditions, Specialized warrants to the original owner for the lifetime of the original owner of each new Specialized bicycle or frameset that the bicycle
frame or frameset when new is free of defective materials and workmanship. The lifetime limited warranty is conditioned upon the bicycle being operated under normal conditions and use, and properly
maintained. This limited warranty does not apply to paint/finish or components attached to the bicycle/frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any
suspension related parts or components. Paint/finish, components attached to the bicycle/ frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension
related parts or components are covered under the limited one (1) year warranty. This warranty is void if the bicycle or frameset was not purchased new from or not properly assembled by an authorized
Specialized dealer.
LIMITED ONE (1) YEAR WARRANTY ON COMPLETE BICYCLE
Subject to the following limitations, terms and conditions, Specialized warrants to the original owner of each new Specialized bicycle that this bicycle when new is free of defective materials and
workmanship. This warranty shall expire one (1) year from the date of the original purchase from an authorized Specialized dealer and is conditioned upon the bicycle being operated under normal
conditions and use, and properly maintained. This warranty is void if the bicycle was not purchased new from or not properly assembled by an authorized Specialized dealer.
LIMITED ONE (1) YEAR WARRANTY ON SUSPENSION ATTACHMENTS & SUSPENSION RELATED EQUIPMENT
Also subject to the following limitations, terms and conditions, Specialized warrants to the original owner of each new Specialized bicycle or frameset that the suspension attachment points, and suspension
related equipment (including pivot points, bushings, shock units, front suspension forks, stays, plates, fasteners) when new are free of defective materials or workmanship. This warranty shall expire one
(1) year from the date of the original purchase from an authorized Specialized dealer and is conditioned upon the bicycle being operated under normal conditions and use, and properly maintained. This
warranty is void if the bicycle was not purchased new from or not properly assembled by an authorized Specialized dealer. Some branded suspension equipment may have additional warranty coverage
offered by the specific manufacturer. Please check in your owner’s manual pack for information regarding these warranties or check with your authorized Specialized dealer for details.
ADDITIONAL CONDITIONS
This Limited Warranty is made only to the original owner of this new Specialized bicycle or frameset purchased from an authorized Specialized dealer, and it shall remain in force only as long as the original
owner retains ownership of the Specialized bicycle. This Limited Warranty is not transferable. In order to exercise your rights under this limited warranty, the bicycle or frameset must be presented to an
authorized Specialized dealer, together with
a
receipt, bill of sale or other appropriate written proof of purchase which identifies the bicycle or frameset by serial number. Should this bicycle, frameset or
any part be determined by Specialized to be covered by this warranty, it will be repaired or replaced, at Specialized’s sole option, which will be conclusive and binding. The original owner shall pay all labor
charges connected with the repair or replacement of all parts. Under no circumstances does this limited warranty include the cost of travel or shipment to and from an authorized Specialized dealer. Such
costs, if any, shall be borne by the original owner. This limited warranty does not apply to normal wear and tear, nor to claimed defects, malfunctions or failures that result from abuse, neglect, improper
assembly, improper maintenance, alteration, collision, crash or misuse. This warranty is null and void if the bicycle is used for racing, trick riding, ramp riding, jumping, riding hard off road, aggressive
riding, riding on severe terrain, riding in severe climates, riding with heavy loads, commercial activities or similar activities. Such use may damage the bicycle, can cause serious personal injury or death,
and in all cases void this warranty.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
USEFUL PRODUCT LIFE CYCLE
Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance
and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to. Uses in competitive events, trick riding, ramp riding,
jumping, aggressive riding, riding on severe terrain, riding in severe climates, riding with heavy loads, commercial activities and other types of non-standard use can dramatically shorten the useful product
life cycle of
a
Specialized bicycle or frameset. Any one or
a
combination of these conditions may result in an unpredictable failure of
a
Specialized bicycle or frameset that would not be covered by this
warranty. ALL SPECIALIZED BICYCLES AND FRAMESETS SHOULD BE PERIODICALLY CHECKED BY AN AUTHORIZED SPECIALIZED DEALER for indicators of stress and/or potential failure, including
cracks, deformation, corrosion, paint peeling, dents, and any other indicators of potential problems, inappropriate use, or abuse. These are important safety checks and very important to help prevent
accidents, bodily injury to the rider and shortened useful product life cycle of a Specialized bicycle or frameset.
Special Note regarding Composite Frames and Components: Composite materials develop their strength and maintain strength only if the integrity of the part is fully maintained. Pay special attention
to, and periodically and carefully inspect composite frames and components for signs of dents, fraying, gouging, scratches, fracture lines, chipping. In the event of
a
crash or serious impact, or if any
of the foregoing signs are observed, the component and frame should not be ridden until inspected by an Authorized Specialized Dealer. For your safety, Specialized recommends replacing composite
handlebars after three years of use.
THIS IS AN INTEGRATED AND FINAL STATEMENT OF SPECIALIZED’S LIMITED WARRANTY. SPECIALIZED DOES NOT AUTHORIZE OR ALLOW ANYONE, INCLUDING ITS AUTHORIZED DEALERS,
TO EXTEND ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, FOR SPECIALIZED. NO OTHER REPRESENTATION, AND NO STATEMENT OF ANYONE BUT SPECIALIZED, INCLUDING A
DEMONSTRATION OF ANY KIND BY ANYONE SHALL CREATE ANY WARRANTY REGARDING THIS BICYCLE OR FRAMESET. ALL OF THE REMEDIES AVAILABLE TO THE ORIGINAL OWNER ARE
STATED HEREIN. IT IS AGREED THAT SPECIALIZED’S LIABILITY UNDER THIS LIMITED WARRANTY SHALL BE NO GREATER THAN THE AMOUNT OF THE ORIGINAL PURCHASE PRICE AND IN NO
EVENT SHALL SPECIALIZED BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
DISCLAIMER
All other remedies, obligations, liabilities, rights, warranties, express or implied, arising from law or otherwise, including but not limited to, any claimed implied warranty of merchantability, any claimed
implied warranty arising from course of performance, course of dealing or usage of trade, and any claimed implied warranty of fitness, are disclaimed by Specialized and waived by the original owner.
Some states, jurisdictions, countries, provinces, do not allow some or all of the limitations set forth herein, or the exclusion or limitation of incidental or consequential damages. If any provision is found
unenforceable, only that provision shall be stricken and all others shall apply. This limited warranty does provide the original owner with certain legal rights and recourse and the original owner may possess
other rights or recourse, depending on the state, jurisdiction, country or province.
2Bliss; 415; A1; AA Main; Aerotec; Air Force; Airliner; Air Lock; Air Tool; Air Wave;Air Wave Mega; Allez; Armadillo; Assfault; Beadlock; BigHit; BigHit Grom; Body Geometry; BrainTrust; Big Mouth; Cap
Ply; Chamonix; Comfort Plush; Crossroads; Demo 9; Deuce; Dirt Bag; Dirtboy; Dirt Control; Dirt Master; Dirt Rodz; Dolce; E5; E Cage; Epic; Evil Twin; Expedition; Extreme Control; Extreme Master;
F.A.C.T.; Fatboy; FlakJacket; Flexflo; ForeArm; FSR; FSRxc; FS-Xpert; Fuse; Globe; Ground Control; Ground Force; Hardlock; Hardlock Rapper; Hardrock; Hardrock’r; Hemi; Hotrock; Hucker; In Vent;
ITch Switch; KidTrust; Kid Cobra; King Cobra; Langster; Little Big Mouth; LSD; M1; M2; M4; M5; Mini-Wedgie; Mt. Baldy; Mondo; Mountain Cage; Mouthport; Nimbus; P.1; P.2;, P.3; P.Brain; P. Street;
Pave; Prybaby; Rib Cage; Rockhopper; Roll Model; Roll X; Roubaix, the Stylized “S” logo; S-Works; S1; Sawpit; Sequoia; Shocksox; Sirrus; Spanky; Speed Zone; Streetboy; Strongarm; Stumpjumper;
SubZero; Survival Kit; Tarmac; Team Control; Team Master; Team Turbo; TrailTraction; TransForm; Tri-Sport; TRX; TR-Xpert; Turbo Pro; Twistlock; Vegas; Web; Wedgie; Wedlock; X-Brace; X-Wire; and
Zertz are trademarks of Specialized Bicycle Components, Inc. which may be registered in some jurisdictions. All other marks are the property of their respective owners.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
15130 Concord Circle
Morgan Hill, CA
95037
© 2003 Specialized Bicycles
PN# W2040162
Download from Www.Somanuals.com. All Manuals Search And Download.
|