OWNER’S MANUAL
AccuFit IW7
In-Wall Loudspeaker
|
AccuFit IW7 Three AccuFit IW7 One
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER INSTALLATION
The unique integral six foot mounting system incorporated into each AccuFit IW7 speaker allows for a quick installation by following
these easy steps:
1. Remove the grille. It may be necessary to push one or two of the mounting screws and its attached foot towards the baffle
and against the inside surface of the grille to force the grille out of its retaining groove.
2. Attach the speaker cable observing the proper polarity with your amplifier: + (red speaker input) to + and – (black speaker
input) to – . Make sure the left channel of the amplifier is connected to the left speaker, and the right channel is connected
to the right speaker.
3. Make sure the mounting feet are turned inward to clear the opening, and insert the speaker into the wall. Position the speaker
into the hole. NOTE: The flange of the speaker is designed to flex and conform to any small imperfections in the wall’s surface.
Tighten the six screws on the front of the baffle only enough to make the flange become snug against the wall. As you tighten
the screws, the feet will automatically flip into an outward position (Figure 3), thereby clamping the drywall between the feet
and the flange.
CAUTION: Over tightening may warp the baffle, crack the ceiling, cause flange to distort, and make the grille difficult to install.
SPEAKER ADJUSTMENTS
Pivoting Tweeter Adjustment
Your AccuFit IW7 Series speakers come from the factory with the tweeter
facing straight out from the baffle. This will result in the overall smoothest
response. However, depending on your particular primary area, room acous-
Push Tweeter Here
tics, or personal preference, you may find the sound more pleasing by point-
ing the tweeters in a particular direction. If additional treble is desired in the
primary listening area, point the tweeter towards that area; and if less treble
is required, point the tweeter away. Push gently at the edge of the tweeter
Figure 4
to point it in the desired direction. (Figure 4)
CAUTION: Avoid touching tweeter dome as damage WILL occur on metal
dome tweeters (AccuFit IW7 Three).
Adjusting the Frequency Response (AccuFit IW7 Three)
The output of the tweeter on the AccuFit IW7 Three can be adjusted to suit
any environment. In general, we recommend leaving all of the adjustments
at the flat (0dB) setting. To determine which settings will be appropriate
for your speakers, you may need to experiment until the desired sound is
achieved. Use the chart to determine the result of the setting you select.
Selecting a Setting on AccuFit IW7 Three
To select a setting, simply use a finger to move the switch mounted on the
Figure 5
inner side of the speaker to the desired setting (Figure 5).
Frequency Settings
When selected, the settings will have the following result:
-3dB: Reduces the loudness of the selected frequency
0dB: The selected frequency remains at neutral level
+3dB: Increases the loudness of the selected frequency
PAINTING THE SPEAKERS
If you plan to paint your speakers, we recommend that it be done prior to
installation. If you plan to paint your speakers sometime in the future, it is best
to remove them by simply reversing the steps for “SPEAKER INSTALLATION”. If
it is necessary to paint the speakers while they are still in the wall, the paint
masks provided in the carton must be installed in place of the grille while
the flange is being painted with the ceiling. The grilles can also be painted,
however, great care should be taken not to clog the holes, as this will greatly
reduce the sound quality of the speakers. SpeakerCraft recommends only
light spray painting using 5 parts thinning agent to 1 part paint. Do not
paint the grilles while they are attached to the speaker. If it is necessary to
paint the under grille material, follow the same procedure used to paint the
grilles.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
AccuFit IW7 Three
AccuFit IW7 One
Speaker Type:
Tweeter:
2 Way with a Shallow-Depth, fully
sealed Steel Enclosure
2 Way Shallow-Depth, fully sealed
Steel Enclosure
Pivoting 1" Aluminum
Dome Tweeter
Pivoting 1" Resin coated Silk
Dome Tweeter
Woofer:
7" Aluminum Cone Woofer
8 ohms
7" Polypropylene Cone Woofer
Impedance:
Sensitivity:
8 ohms
91dB 1W/1m
90dB 1W/1m
None
Frequency Adjustments:
Front-Mounted Treble Switch allows
the Treble to be set at one of 3 posi-
tions: –3dB, Flat, +3dB
Frequency Response:
Power Handling:
40Hz - 20kHz
5-125 watts
40Hz - 20kHz
5-100 watts
Cut Out Dimensions (H x W):
12 3⁄4" x 8 1⁄16"
(323.8mm x 206.3mm)
12 3⁄4" x 8 1⁄16"
(323.8mm x 206.3mm)
Dimensions (H x W x D):
14 1⁄2" x 9 7⁄8" x 2 3⁄4
(368.3mm x 250.8mm x 70mm)
"
14 1⁄2" x 9 7⁄8" x 2 3⁄4
(368.3mm x 250.8mm x 70mm)
"
In our attempt to constantly improve our products, features and specifications are subject to change without notice.
LIMITED LIFETIME WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship,
provided the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were
purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is pref-
erable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit
is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in
materials or workmanship at any time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace
this product at no additional charge, except as set forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft,
at its sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification
to the mounting surface may be required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modi-
fication. All replaced parts and product become the property of SpeakerCraft Inc. Products replaced or repaired under this Warranty will be returned
to the original retail purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or
shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which
has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions.
This warranty will be void if the Serial Number on the product has been removed, tampered with or defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted
above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be
liable for any incidental or consequential damages arising out of the use or inability to use the product, even if SpeakerCraft
Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such damages, or for any claim by any
other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation
on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.
SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy, economical, and professional. Contact
your authorized SpeakerCraft Dealer for more information. For technical inquires, please call 1-800-448-0976 or e-mail us at [email protected].
We are available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
940 Columbia Ave., Riverside CA 92507 | USA (800) 448 0976 Fax (951) 787 8747 International +1 951 787 0543 | www.speakercraft.com
LIT68700(rev1)
Download from Www.Somanuals.com. All Manuals Search And Download.
|