In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
From Box Here:
REQUIRED TOOLS AND MATERIALS:
WARNING!
• 3 Capable Adults
• (2) Stepladders 8 ft. (2.4 m)
•
• Carpenter’s Level
• 15’ Tape Measure
• Safety Goggles
• Container to Mix
• (2 each) Wrenches and/or Socket Wrenches and
Sockets (Deep-Well Sockets are Recommended).
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Shovel & Post Hole
Digger
3/8"
1/2"
9/16"
3/4"
15/16"
• Optional: Large &
Small Adjustable
Wrenches
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
• Phillips Screwdriver
• (1) Utility Knife
3/8"
1/2"
9/16"
3/4"
15/16"
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234 Canada Only: 1-800-284-8339
© COPYRIGHT 2006 by SPALDING
02/06
ID# M880961
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Ensure ground is level with playing
surface, then dig pole hole.
PLAYING
SURFACE
WARNING!
24" (61 cm)
36" (91.4 cm)
GROUND
SURFACE
CONTACT UTILITIES
BEFORE DIGGING.
2.
Install nut (2) to J-bolt (1) as
shown. Repeat procedure for
other three J-bolts (1).
2
2-1/2”
(6.35 cm)
3
2
IMPORTANT!
Make sure nuts are 2-1/2”
(6.35cm) from top of
J-Bolts.
1
2
NOTE:
Make sure J-bolts (1) are
in the illustrated position.
1
3.
Install threaded ends of J-bolts (1) through holes in
mounting plate (3) and secure as shown.
NOTE:
Nuts on the top of plate are
used for leveling the pole after
system is fully assembled.
02/06
ID# M880961
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Fill hole with concrete. Tamp down concrete to release air
pockets and build drainage hill.
5.
Insert J-bolts (1) from mounting plate (3) into cement as shown.
Move assembly around to release any air pockets in cement,
then rest mounting plate on cement drainage hill. Apply some
pressure to level mounting plate on top of drainage hill. Level
mounting plate and square with playing surface. Clean off any
excess cement on mounting plate at this time.
IMPORTANT!
PLAYING SURFACE
Front of mounting plate (3)
must be parallel with
playing surface.
3
WARNING!
DO NOT PROCEED UNTIL
CONCRETE HAS CURED! A
MINIMUM OF 72 HOURS. ALLOW
ADDITIONAL TIME FOR COLD,
WET OR HUMID WEATHER.
1
IMPORTANT!
Check leveling of mounting
plate several times with
carpenter’s level while
concrete is curing.
ID# M880961
02/06
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
THREE CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
5
6.
Upright pole (5). Assemble lower pole flange
onto protruding J-bolts (1) as shown. The flange
will then rest on the nuts (2).
IMPORTANT!
Holes in pole must be
parallel with playing
surface.
PLAYING SURFACE
7.
Secure pole (5) flange to mounting plate (3)
as shown. Tighten completely.
NOTE:
Position crank jack
mounting as shown.
5
2
6
2
6
2
6
2
6
6
6
1
P
S
U
L
A
6
Y
R
6
I
F
N
A
G
C
1
3
E
02/06
ID# M880961
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Beginning with upper support arm (8) secure support
arms to pole. Continue by securing lower support
arm (9) as shown.
WARNING!
THREE CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
IMPORTANT!
Do Not Over Tighten.
27
28
27
28
14
28
13
8
13
28
12
27
28
27
28
9
13
14
28
28
7
13
12
7
14
33
IMPORTANT!
Bushing
types are
identified
with a letter.
27
28
ID# M880961
02/06
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure backboard to support arms (8 and 9) as
shown.
9.
IMPORTANT!
Bushing
types are
identified
with a letter.
IMPORTANT!
Do Not Over Tighten.
28
13
13
27
14
28
28
28
14
13
10
8
10
27
13
13
28
28
14
27
10
13
9
27
28
02/06
ID# M880961
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure jack brackets (21) to to mounting bracket as shown.
10.
14
13
13
11
21
21
G
N
I
Y
U
A
S
L
E
P
C
A
F
REAR VIEW
R
20
11.
NOTE:
Position U-joint of crank jack (20)
as shown. Where tubes on crank
jack join, hold steady to keep both
tubes from rotating. Rotate handle
clockwise on crank jack to the
fully extended position.
IMPORTANT!
Hold Here.
ID# M880961
02/06
8
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Insert spacer (4) through spacer of screw jack as shown.
12.
A.
WARNING!
B. Install crank jack (20) U-joint to lower support arm (9) as shown.
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
4
20
20
9
IMPORTANT!
Bushing
types are
identified
with a letter.
B.
28
28
14
9
27
28
12
28
13
28
13
REAR VIEW
20
IMPORTANT!
Do Not Over Tighten.
02/06
ID# M880961
9
Download from Www.Somanuals.com. All Manuals Search And Download.
13.
Rotate jack handle until jack (20) aligns with jack brackets (21). Secure crank jack (20)
to jack brackets (21) as shown.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
20
15
14
15
13
34
21
13
REAR VIEW
NOTE:
Some adjustment will be necessary
to align the lower crank jack and
bushings to jack brackets (21).
ID# M880961
02/06
10
Download from Www.Somanuals.com. All Manuals Search And Download.
14.
Set-up For Leftt Side
Set-up For Right Side
Apply height indicator
labels (18 and 19) to
height indicators (16).
A.
16
16
10
10
8 7
9
9
7
8
18
10
19
9
10
7
8
9
8 7
B. Attach height indicators (16) to lower arm in areas as
shown by turning screws (17) into place with a phillips
screwdriver.
IMPORTANT!
Note Orientation of Height
Indicators: 10’ Mark Should
Face Away From Backboard.
16
16
0
17
17
02/06
ID# M880961
11
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
Install net (30) to rim as shown.
A.
B.
D.
C.
30
30
Attach rim assembly (29). For rim assembly, see
instructions included with rim.
16.
23
29
Rim Assembly
24
25
22
25
Remove rim cover
prior to installing rim
assembly to board.
IMPORTANT!
Refer To Instructions
Included With Rim
Hardware For Rim
Assembly.
Carefully cut and peel
protective film away from
board prior to attaching rim.
ID# M880961
02/06
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Check leveling at this time. Pole (5) should
be level in all directions. After system is
leveled, completely tighten nuts (2) above
pole flange.
17.
5
NOTE:
If adjustment is necessary, adjust
system by rotating the nuts (2)
between mounting plate (3) and
pole flange.
2
Apply height adjustment label (31) to
front of pole as shown.
18.
REGULATION
RIM HEIGHT IS
10 FEET (3.05 m).
31
02/06
ID# M880961
13
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Secure pole pad (32) as
shown.
19.
NOTE:
Pole pad may NOT be
included in this model.
Height Adjustment
20.
Rotate crank handle to raise or lower backboard.
NOTE:
If height adjustment is difficult to
operate, you may have over
tightened the areas indicated.
ID# M880961
02/06
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item Qty. Part No. Description
18
19
20
21
22
1
1
1
2
4
2
2
6
204739 Label, Height Indicator, Right
204740 Label, Height Indicator, Left
222880 Crank, Jack
1
2
4
200573 J-Bolt, 1/2-13 x 24” Long
12 265575 Nut, Hex, 5/8-11
908292 Bracket, Crank Jack Support
203017 Nut, Hex, 3/8-16
3
1
1
1
8
2
1
1
4
3
3
900661 Anchor Plate
4
220579 Spacer, 0.53 I.D. x 0.75 O.D. x 5” Long
908310 Pole
23
24
25
26
27
28
29
30
31
32
205347 Bolt, Carriage, 3/8-16 x 3.5” Long
200512 Bolt, Hex, Tap, 3/8-16 x 3.5” Long
203309 Washer, Flat, 3/8”
5
6
200704 Washer, 5/8” x 1.5 O.D.
7
205125 Spacer, 0.53 I.D. x 0.75 O.D. x 1.88” Long
908312 Support Arm, Upper
4* 203300 Washer, 3/8 Locking,
204670A Bushing, Plastic
20 204670C Bushing, Plastic
8
8
9
908311 Support Arm, Lower
10
11
12
13
14
15
16
17
206271 Bolt, Hex Head, 1/2-13 x 2-1/2” Long
205516 Bolt, Hex Head, 1/2-13 x 5.75” Long
205515 Bolt, Hex Head, 1/2-13 x 10.25” Long
1
1
1
1
Rim
Net
200685 Label, Height Adjustment
205600 Pole Pad, Hydra-Rib (May Not Be Included)
20 202651 Washer, Flat, 1/2”
11 206340 Lock Nut, Hex 1/2-13
1
1
205600S Pole Pad, Spalding (May Not Be Included)
205515 Bolt, Hex, 1/2-13 x 10.25” Long
2
2
4
205082 Spacer, 0.53 I.D. x 0.75 O.D. x .38 Long
204735 Height Indicator
33
34
1
205076 Bolt, Hex, 1/2-13 x 5.5” Long
204733 Screw, #8 x .050” Long
* You May Have Extra Parts With This Model.
Item Qty. Part No. Description
HARDWARE IDENTIFIER (BOLTS)
Item #24 (2)
Item #17 (4)
Item #10 (4)
Item #23 (2)
Item #11 (3)
Item #33 (1)
02/06
ID# M880961
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (NUTS, WASHERS & STEEL SPACERS)
Item #4 (1)
Item #6 (8)
Item #2 (12)
Item #26 (4)*
Item #13 (20)
Item #14 (11)
Item #22 (4)
Item #7 (2)
Item #25 (6)
HARDWARE IDENTIFIER (PLASTIC & NYLON SPACERS)
Item #15 (2)
Item #28 (20)
Item #27 (8)
* You May Have Extra Parts With This Model.
ID# M880961
02/06
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|