3-090-238-E2 (1) GB
Video Cassette
Recorder
Operating Instructions
PAL
SLV-SE840D/E
SLV-SE747E
SLV-SE740D/E
SLV-SX740D/E
SLV-SE640D/E
SLV-SE240D
© 2004 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
WARNING
Television programmes, films, video tapes and other
materials may be copyrighted. Unauthorized
recording of such material may be contrary to the
provisions of the copyright laws. Also, use of this
recorder with cable television transmission may
require authorization from the cable television
transmitter and/or programme owner.
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Compatible colour systems
This VCR is designed to record using the PAL (B/
G) colour system and play back using the PAL (B/
G) colour system. Recording of video sources based
on other colour systems cannot be guaranteed.
Mains lead must only be changed at a qualified
service shop.
Precautions
Safety
SHOWVIEW is a registered trademark of Gemstar
Development Corporation. The SHOWVIEW system
is manufactured under license from Gemstar
Development Corporation.
•
•
•
•
This unit operates on 220 – 240 V AC, 50 Hz.
Check that the unit’s operating voltage is
identical with your local power supply.
If anything falls into the cabinet, unplug the unit
and have it checked by qualified personnel before
operating it any further.
The unit is not disconnected from the mains as
long as it is connected to the mains, even if the
unit itself has been turned off.
Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never
by the cord.
Installing
•
•
•
Do not install this equipment in a confined space
such as a book or similar unit.
Allow adequate air circulation to prevent internal
heat buildup.
Do not place the unit on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that
may block the ventilation slots.
•
Do not install the unit near heat sources such as
radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical
vibration or shock.
•
•
Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position
only.
Keep the unit and cassettes away from equipment
with strong magnets, such as microwave ovens or
large loudspeakers.
•
•
Do not place heavy objects on the unit.
If the unit is brought directly from a cold to a
warm location, moisture may condense inside the
VCR and cause damage to the video head and
tape. When you first install the unit, or when you
move it from a cold to a warm location, wait for
about three hours before operating the unit.
WARNING
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
57 Playing/searching at various speeds
59 Setting the recording duration time
60 Synchronized Recording
(not available on SLV-SE640D/E and
SE240D)
4 Index to parts and controls
11 Step 1 : Unpacking
12 Step 2 : Setting up the remote
commander
16 Step 3 : Connecting the VCR
20 Step 4 : Setting up the VCR with
the Auto Set Up function
62 Checking/changing/cancelling
timer settings
64 Recording stereo and bilingual
programmes (not available on
SLV-SE240D)
67 Searching using the index function
(not available on SLV-SE240D)
69 Adjusting the picture
70 Reducing the VCR’s power
consumption
23 Setting the clock
25 Downloading the TV tuner’s preset
data (not available on SLV-SE640D/
E and SE240D)
26 Selecting a language
27 Presetting channels
30 Changing/disabling programme
positions
71 Changing menu options
decoder
73 Connecting to a VCR or stereo
system
75 Basic editing
38 Playing a tape
41 Recording TV programmes
only)
45 Recording TV programmes using
the Dial Timer (SLV-SE840D/E
only)
50 Recording TV programmes using
the ShowView® system (not
available on SLV-SE640D/E and
SE240D)
54 Recording TV programmes using
the timer
77 Troubleshooting
81 Specifications
82 Index
Back Cover
Quick Start Guide
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
For SLV-SE840D/E
A ?/1 (on/standby) switch
C Tape compartment
J AUDIO DUB button (76)
L SYNCHRO REC (Synchronized
Recording) button (61)
M t LINE-2 L (left) o R (right)
How to open the jack cover
1 Press the bottom of the cover.
2 Hook your finger on the top edge of the
cover and pull it open.
* The H (play), PROGRAM + buttons and
jack cover have a tactile dot.
I
DIAL TIMER (45)
Index to parts and controls
4
Download from Www.Somanuals.com. All Manuals Search And Download.
For SLV-SE747E, SE740D/E, SX740D/E and SE640D/E
A ?/1 (on/standby) switch
C Tape compartment
J SYNCHRO REC (Synchronized
2
*1 The H (play) and PROGRAM + buttons
have a tactile dot.
*2 not available on SLV-SE640D/E
continued
Index to parts and controls
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For SLV-SE240D
A ?/1 (on/standby) switch
D Tape compartment
* The H (play) and PROGRAM + buttons
have a tactile dot.
Index to parts and controls
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Display window
For SLV-SE840D/E, SE747E, SE740D/E and SX740D/E
1
2
3
4
5
8
A Tape indicator
7
6
C Time counter/clock/line/programme
D
(smartlink) indicator (18)
For SLV-SE640D/E and SE240D
A Tape indicator
G Playback indicator
B Time counter/clock/line/programme
* not available on SLV-SE240D
continued
Index to parts and controls
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
For SLV-SE840D/E, SE747E, SE740D/E, SX740D/E and SE640D/E
For SLV-SE240D
A
(in from antenna) connector (16)
B LINE-3 (DEC/EXT) connector*1
LINE-2 (DEC/EXT) connector*2
F
*1 SLV-SE840D/E
*2 SLV-SE747E, SE740D/E, SX740D/E,
SE640D/E and SE240D
*3 not available on SLV-SE640D/E
D AUDIO (OUT/SORTIE) R/D (right)
L/G (left) jacks*3 (19)
Index to parts and controls
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote commander
B
C
E Programme number buttons*1 (13)
G / (Teletext) button (for TV)*2 (14)
1
4
7
2
5
8
0
3
6
9
I a TV power on/TV mode select
button (for TV)*2 (13)
K SP (Standard Play)/LP (Long Play)
button*3 (41)
*1 The H (play), AUDIO MONITOR,
number 5 and PROG + buttons have a
tactile dot.
*2 SLV-SE840D/E and SE747E only
*3 not available on SLV-SE240D
continued
Index to parts and controls
9
Download from Www.Somanuals.com. All Manuals Search And Download.
N [TV] / [VIDEO] remote control switch
1
4
7
2
5
8
0
3
6
9
T PROG (programme) +/– buttons*1
c ⁄ C Teletext page access buttons
(for TV)*2 (14)
U y SLOW button*4 (57)
V ×2 button*4 (57)
W ./> (index search)
buttons*3*4 (67)
X
*1 The H (play), AUDIO MONITOR,
number 5 and PROG + buttons have a
tactile dot.
*2 SLV-SE840D/E and SE747E only
*3 not available on SLV-SE240D
*4 FASTEXT buttons (for TV)
(SLV-SE840D/E and SE747E only)
Index to parts and controls
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1 : Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• R6 (size AA) batteries
• Aerial cable
Note
• The supplied remote commander is for the exclusive use of this VCR.
How to use this manual
The instructions in this manual are for the 10 models: SLV-SE840D, SE840E,
SE747E, SE740D, SE740E, SX740D, SX740E, SE640D, SE640E and SE240D.
Check your model name by looking at the rear panel of your VCR.
SLV-SE840D/E is the model used for illustration purposes. Any difference in
operation is clearly indicated in the text, for example, “SLV-SE840D/E only.”
This manual mainly explains operations using the remote, but the same operations
can also be performed using the buttons on the VCR having the same or similar
names.
Unpacking
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2 : Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
Remote sensor
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV. If the TV does not have
the
symbol near the remote
[TV] /
[VIDEO]
sensor, this remote commander
will not operate the TV.
1
4
7
2
5
8
0
3
6
9
To operate
the VCR
Set [TV] / [VIDEO] to
[VIDEO] and point at the remote sensor at the VCR
a Sony TV
[TV] and point at the remote sensor at the TV
Setting up the remote commander
12
Download from Www.Somanuals.com. All Manuals Search And Download.
?/1
AUDIO MONITOR
DISPLAY
t TV/VIDEO
1
4
7
2
5
8
0
3
6
9
Programme
number
buttons
-
/
PROG +/–/
2 +/–
a
c ⁄ C
FASTEXT buttons
TV control buttons
To
Press
Set the TV to standby mode
?/1
Select an input source: aerial in or line in
Select the TV’s programme position
t TV/VIDEO
Programme number buttons,
-, PROG +/–
Adjust the volume of the TV
Switch to TV (Teletext off)*1
2 +/–
a (TV)
continued
Setting up the remote commander
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
Switch to Teletext*1
Select the sound*2
Use FASTEXT*1
Call up the on-screen display
/ (Teletext)
AUDIO MONITOR
FASTEXT buttons
DISPLAY
Change the Teletext page*1
c ⁄ C
Switch to/from wide mode of a Sony wide TV (For
other manufactures’ wide TVs, see “Controlling
SE840D/E and SE747E only)” below.)
(wide)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing
the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus.
Doing so may cause a malfunction.
• Some buttons may not work with certain Sony TVs.
*1 SLV-SE840D/E and SE747E only
*2 not available on SLV-SE240D
Controlling other TVs with the remote commander
(SLV-SE840D/E and SE747E only)
The remote commander is preprogrammed to control non-Sony TVs. If your
TV is listed in the following table, set the appropriate manufacturer’s code
number.
1 Set [TV] / [VIDEO] at the top of the remote commander to [TV].
Hold down ?/1, and enter your TV’s code number using the programme
number buttons. Then release ?/1.
2
Now you can use the following TV control buttons to control your TV:
?/1, t TV/VIDEO, programme number buttons, - (ten’s digit),
PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons,
(wide)*, MENU*, M/m/</,*, and OK*.
* These buttons may not work with all TVs.
Setting up the remote commander
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable
code numbers.
Manufacturer
Sony
Code number
Manufacturer
Panasonic
Philips
Code number
01*1, 02
17*1, 49
06*1, 07*1, 08*1
Akai
68
Ferguson
Grundig
Hitachi
JVC
52
Saba
12, 13
22, 23
25
10*1, 11*1
Samsung
Sanyo
24
33
Sharp
29
Loewe
Mivar
45
Telefunken
Thomson
Toshiba
36
43*2
38
09, 70
NEC
66
15, 16, 69*3
Nokia
*1 Press
*2 Press
*3 Press
(wide) to switch the wide picture mode on or off.
(wide), then press 2 +/– to select the wide picture mode you want.
(wide). The menu appears on the TV screen. Then, press M/m/</, to
select the wide picture you want and press OK.
Tip
• When you set your TV’s code number correctly while the TV is turned on, the TV
turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be
erased.
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
Setting up the remote commander
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 : Connecting the VCR
If your TV does not have a Scart (EURO-AV) connector
Mains lead
AERIAL IN
Aerial cable (supplied)
to mains
: Signal flow
Disconnect the aerial cable from your
1
2
3
TV and connect it to
panel of the VCR.
on the rear
Connect
of the VCR and the aerial
input of your TV using the supplied
aerial cable.
Connect the mains lead to the mains.
Note
• When you connect the VCR and your TV only with an aerial cable, you have to
Connecting the VCR
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If your TV has a Scart (EURO-AV) connector
LINE-1 (EURO AV)
Mains lead
to mains
AERIAL IN
Aerial cable (supplied)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Disconnect the aerial cable from
your TV and connect it to on
the rear panel of the VCR.
1
Connect
aerial input of your TV using the
supplied aerial cable.
of the VCR and the
2
3
Connect LINE-1 (EURO AV) on
the VCR and the Scart (EURO-
AV) connector on the TV with the
optional Scart cable.
This connection improves picture
and sound quality. Whenever you
want to watch the VCR picture,
press t TV/VIDEO to display
the VIDEO indicator in the
display window.
Connect the mains lead to the mains.
4
continued
Connecting the VCR
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About the SMARTLINK features (not available on SLV-SE640D/E
and SE240D)
If the connected TV complies with
SMARTLINK, MEGALOGIC*1,
EASYLINK*2, Q-Link*3, EURO
VIEW LINK*4, or T-V LINK*5, this
VCR automatically runs the
SMARTLINK function after you complete the steps on the previous page
(the
indicator appears in the VCR’s display window when you turn on the
TV). You can enjoy the following SMARTLINK features.
• TV Direct Rec
You can easily record what you are watching on the TV when the VCR is
44.
• One Touch Play
With One Touch Play, you can start playback automatically without turning
• One Touch Menu
When the VCR is turned on, you can turn on the TV, set the TV to the
video channel, and display the VCR’s on-screen display automatically by
pressing MENU on the remote commander.
• One Touch Timer
When the VCR is turned on, you can turn on the TV, set the TV to the
video channel, and display the timer recording menu (the TIMER
PROGRAMMING menu or the SHOWVIEW menu) automatically by
pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER
• NexTView Download
You can easily set the timer by using the NexTView Download function on
your TV. Please refer to your TV’s instruction manual.
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation.
*2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation.
*5 “T-V LINK” is a trademark of JVC Corporation.
Note
• Not all TVs respond to the functions above.
Connecting the VCR
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional connections
To a stereo system (not
available on SLV-
SE640D/E and SE240D)
AUDIO R/D L/G
You can improve sound
quality by connecting a
stereo system to the AUDIO
R/D L/G jacks as shown on
the right.
LINE IN
Audio cable (not supplied)
: Signal flow
To a satellite or digital
tuner with Line Through
Using the Line Through
function, you can watch
programmes from a satellite
or digital tuner connected to
this VCR on the TV even
when the VCR is turned off.
When you turn on the
satellite or digital tuner, this
VCR automatically sends the
signal from the satellite or
digital tuner to the TV
LINE-3 (DEC/EXT)*1 or
LINE
OUT
LINE-2 (DEC/EXT)*2
Scart cable (not supplied)
: Signal flow
without turning itself on.
Connect the satellite or digital tuner to the LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2 connector as shown above.
1
2 Turn off the VCR.
To watch a programme, turn on the satellite or digital tuner and the TV.
Notes
• The Line Through function will not operate properly if POWER SAVE in the
USER SET menu is set to ECO2. Set POWER SAVE to OFF or ECO1 to ensure
• You cannot watch programmes on the TV while recording unless you are recording
a satellite or digital programme.
• This function may not work with some types of satellite or digital tuners.
• When the VCR is turned off, set the TV to the video channel.
*1 SLV-SE840D/E
*2 SLV-SE747E, SE740D/E, SX740D/E, SE640D/E and SE240D
Connecting the VCR
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 : Setting up the VCR with the Auto
Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up
function. With this function, you can set the language for the on-screen display, TV
channels, guide channels for the ShowView system*, and VCR clock* automatically.
Turn on your TV and set it to the video channel.
1
If your TV does not have a Scart (EURO-AV) connector, tune the
TV to channel 32 (the initial RF channel for this VCR). Refer to
your TV manual for TV tuning instructions. If the picture does not
appear clearly, see “To change the RF channel” on page 22.
Connect the mains lead to the
mains.
2
GB
ES
NL
FI
DE
IT
SE
GR
FR
PT
DK
TR
The VCR automatically turns on,
and the language abbreviations
appear on the TV screen.
SELECT
SET
:
: OK
EXIT : MENU
The abbreviations of the
languages are as follows:
Abbreviation Language
Abbreviation Language
GB
ES
NL
FI
English
Spanish
Dutch
SE
GR
FR
PT
DK
TR
Swedish
Greek
French
Finnish
German
Italian
Portuguese
Danish
DE
IT
Turkish
Press M/m/</, to select the language abbreviation from the table
in step 2, then press OK.
3
OK
The message for the Auto Set Up function appears.
Setting up the VCR with the Auto Set Up function
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Press OK.
4
COUNTRY SELECTION
The COUNTRY SELECTION
menu* appears.
OK
A
B
I
TR
N
P
E
GR
HU
PL
CZ
DK
FIN
D
S
NL
CH
OTHERS
SELECT
SET
:
: OK
EXIT : MENU
The abbreviations of the
countries are as follows:
Abbreviation Country
Abbreviation Country
A
Austria
E
Spain
B
Belgium
Denmark
Finland
Germany
Netherlands
Italy
S
Sweden
Switzerland
Turkey
Greece
Hungary
Poland
DK
FIN
D
CH
TR
GR
HU
PL
CZ
NL
I
N
Norway
Portugal
Czech
P
For SLV-SE840D/E, SE747E,
SE740D/E, SX740D/E and
SE240D
5
OK
AUTO SET UP
PLEASE WAIT
Press M/m/</, to select the
abbreviation of your country from
the table in step 4, then press OK.
If your country does not appear,
select OTHERS.
4 0 %
EXIT : MENU
The VCR starts searching for all of the receivable channels and
presets them (in the appropriate order for your local area).
If you want to change the order of the channels or disable unwanted
programme positions, see “Changing/disabling programme
After the search or download is complete, the current time appears
for any stations that transmit a time signal. If the time does not
For SLV-SE640D/E
continued
Setting up the VCR with the Auto Set Up function
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on
the VCR and TV. Select INSTALLATION from the menu, then press M/m
to highlight VCR OUTPUT CH and press ,. Select the RF channel by
pressing the M/m buttons. Then, tune the TV to the new RF channel so that
a clear picture appears.
Tip
• If you want to change the language for the on-screen display from the one preset in
Notes
• Whenever you operate the Auto Set Up function, some of the settings
(ShowView*, timer, etc.) will be reset. If this happens, you have to set them again.
• Auto preset starts automatically only when you plug in the mains lead for the first
time after you purchase the VCR.
• After using the Auto Set Up function, the language abbreviations do not appear
automatically when you connect the mains lead again. If you want to use the Auto
Set Up function again, press MENU, then press M/m/</, to highlight
INSTALLATION and press OK. Press M/m to highlight AUTO SET UP, then
repeat all procedures from step 4.
• Auto preset can be performed by pressing x (stop) on the VCR continuously for 5
seconds or more with no tape inserted.
* not available on SLV-SE640D/E
Setting up the VCR with the Auto Set Up function
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the clock
You must set the time and date on the VCR to use the timer features properly.
The Auto Clock Set function* works only if a station in your area is broadcasting a
time signal.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight CLOCK SET and
press OK.
1 2 : 0 0
1
/ JAN / 2 0 0 4
THU
AUTO CLOCK
:
ON
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to set the hour.
2
3
4
OK
1 8 : 0 0
1
/ JAN / 2 0 0 4
THU
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press , to select the minutes and
set the minutes by pressing M/m.
OK
1 8 : 3 0
1
/ JAN / 2 0 0 4
THU
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Set the day, month, and year in
sequence by pressing , to select
the item to be set, and press M/m to
select the digits, then press ,.
OK
1 8 : 3 0 2 8 / SEP / 2 0 0 4
TUE
AUTO CLOCK
:
ON
The day of the week is set
automatically.
SELECT
END
:
SET
EXIT : MENU
:
: OK
continued
Setting the clock
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to select ON for the
setting of the Auto Clock Set
function*.
5
6
OK
1 8 : 3 0 2 8 / SEP / 2 0 0 4
TUE
The VCR automatically sets the
clock according to the time signal
broadcast between the channels
PR 1 to PR 5.
AUTO CLOCK
:
ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
If you do not need the Auto Clock
Set function, select OFF.
Press MENU to exit the menu.
MENU
Tips
• If you set AUTO CLOCK* to ON, the Auto Clock Set function is activated
whenever the VCR is turned off. The time is adjusted automatically by making
reference to the time signal from the station.
• To change the digits while setting, press < to return to the item to be changed, and
select the digits by pressing M/m.
* not available on SLV-SE640D/E
Setting the clock
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading the TV tuner’s preset data
(not available on SLV-SE640D/E and SE240D)
You can download your TV tuner’s preset data to the VCR and tune the VCR
according to that data using the SMARTLINK connection.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
MANUAL SET UP
SMARTLINK
and press OK.
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight
2
3
SMARTLINK
SMARTLINK, then press ,.
OK
TV CH DOWNLOAD
TV DIRECT RECORD : ON
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press M/m to highlight TV CH
DOWNLOAD, then press ,.
Press , again. The Preset
Download function starts and the
indicator flashes in the display
window during download.
TV CH DOWNLOAD
PLEASE WAIT
OK
4 0 %
END
: OK
EXIT : MENU
Downloading the TV tuner’s preset data (not available on SLV-SE640D/E and SE240D)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a language
You can change the on-screen display language from the one you selected with the
Auto Set Up function.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight LANGUAGE SET
GB
ES
NL
FI
DE
IT
SE
GR
FR
PT
DK
TR
and press OK.
OK
SELECT
SET
:
: OK
EXIT : MENU
Press M/m/</, to highlight the abbreviation of the desired
2
OK
Selecting a language
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting channels
If some channels could not be preset using the Auto Set Up function, you can preset
them manually.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
MANUAL SET UP
SMARTLINK
and press OK.
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
TV STATION TABLE
SET UP, then press ,.
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
0 2 7
0 2 9
0 3 0
0 3 2
OFF
OFF
OFF
OFF
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to preset, then press
,.
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
MANUAL TUNING
OK
PR
CH
MFT
:
:
:
:
:
5
– – –
–
OFF
– – – –
DECODER
NAME
SELECT
END
:
SET
EXIT : MENU
:
: OK
continued
Presetting channels
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Press </, repeatedly until the
4
5
6
MANUAL TUNING
channel you want is displayed.
OK
OK
OK
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
DECODER
NAME
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press M/m to highlight NAME, then
press ,.
MANUAL TUNING
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
DECODER
NAME
SELECT
END
:
SET
:
: OK
EXIT : MENU
Enter the station name.
MANUAL TUNING
1 Press M/m to select a character.
Each time you press M, the
character changes as shown
below.
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
O– – –
DECODER
NAME
A t B t … t Z t 0 t 1 t
… t 9 t A
SELECT
END
:
SET
EXIT : MENU
:
: OK
2 Press , to set the next character.
The next space flashes.
To correct a character, press </, until the character you want
to correct flashes, then reset it.
You can set up to 4 characters for the station name.
Press OK to confirm the station name.
7
8
OK
Press MENU to exit the menu.
MENU
Presetting channels
28
Download from Www.Somanuals.com. All Manuals Search And Download.
If the picture is not clear
If the picture is not clear, you may use the Manual Fine Tuning (MFT)
function. After step 4, press M/m to select MFT. Press </, to get a clear
picture, then press MENU to exit the menu.
Tips
• The VCR must receive channel information for station names to appear
automatically.*
Note
• When adjusting MFT, the menu may become difficult to read due to interference
from the picture being received.
* not available on SLV-SE640D/E
Presetting channels
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/disabling programme positions
After setting the channels, you can change the programme positions as you like. If
any programme positions are unused or contain unwanted channels, you can disable
them.
You can also change the station names. If the station names are not displayed, you can
enter them manually.
Changing programme positions
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
MANUAL SET UP
SMARTLINK
and press OK.
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
TV STATION TABLE
SET UP, then press ,.
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
0 2 7
0 2 9
0 3 0
0 3 2
OFF
OFF
OFF
OFF
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
containing the programme position
you want to change.
TV STATION TABLE
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
OFF
OFF
OFF
OFF
0 2 7
0 2 9
0 3 0
0 3 2
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Changing/disabling programme positions
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Press OK, then press M/m to move
4
5
TV STATION TABLE
to the desired programme position.
OK
PR
1
2
3
4
CH
0 2 7
NAME
A A B –
DEC
OFF
0 3 0
0 3 2
0 2 9
CDE –
OFF
OFF
OFF
I
J K –
5
L MN–
SWAPPING : OK
EXIT : MENU
Press OK to confirm the setting.
OK
To change the programme position of another station, repeat steps 3
through 5.
6
7
Press MENU to exit the menu.
MENU
Disabling unwanted programme positions
After presetting channels, you can disable unused programme positions. The disabled
positions will be skipped later when you press the PROG +/– buttons.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION,
AUTO SET UP
MANUAL SET UP
SMARTLINK
and press OK.
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
continued
Changing/disabling programme positions
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Press M/m to highlight MANUAL
2
3
4
TV STATION TABLE
SET UP, then press ,.
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
0 2 7
0 2 9
0 3 0
0 3 2
OFF
OFF
OFF
OFF
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to disable.
TV STATION TABLE
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
OFF
OFF
OFF
OFF
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
0 2 7
0 2 9
0 3 0
0 3 2
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press CLEAR.
CLEAR
TV STATION TABLE
The selected row will be cleared as
shown on the right.
PR
1
2
CH
0 2 7
NAME
A A B –
DEC
OFF
3
4
0 3 0
0 3 2
CDE –
OFF
OFF
I
J K –
5
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Repeat steps 3 and 4 for any other programme positions you want to
disable.
5
6
Press MENU to exit the menu.
MENU
Note
• Be sure to select the programme position you want to disable correctly. If you
disable a programme position by mistake, you need to reset that channel manually.
Changing/disabling programme positions
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the station names
You can change or enter the station names (up to 4 characters). The VCR must
receive channel information for station names to appear automatically*.
* not available on SLV-SE640D/E
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the video channel.
Press MENU, then press M/m/</
MENU
1
, to highlight INSTALLATION
AUTO SET UP
MANUAL SET UP
SMARTLINK
and press OK.
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight MANUAL
2
3
4
TV STATION TABLE
SET UP, then press ,.
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
0 2 7
0 2 9
0 3 0
0 3 2
0 3 3
OFF
OFF
OFF
OFF
OFF
I
J K –
5
– – – –
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to change or enter
the station name, then press ,.
To display other pages for
programme positions 6 to 80, press
M/m repeatedly.
MANUAL TUNING
OK
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
DECODER
NAME
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to highlight NAME, then
press ,.
MANUAL TUNING
OK
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
DECODER
NAME
SELECT
END
:
SET
EXIT : MENU
:
: OK
continued
Changing/disabling programme positions
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the station name.
5
MANUAL TUNING
1 Press M/m to select a character.
Each time you press M, the
character changes as shown
below.
OK
PR
CH
MFT
:
:
:
:
:
5
0 3 3
–
OFF
O– – –
DECODER
NAME
A t B t … t Z t 0 t 1 t
… t 9 t A
SELECT
END
:
SET
EXIT : MENU
:
: OK
2 Press , to set the next character.
The next space flashes.
To correct a character, press </, until the character you want
to correct flashes, then reset it.
You can set up to 4 characters for the station name.
Press OK to confirm the new name.
6
7
OK
Press MENU to exit the menu.
MENU
Changing/disabling programme positions
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PAY-TV/Canal Plus decoder
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder
(not supplied) to the VCR.
Connecting a decoder
PAY-TV/Canal
Plus decoder
Scart cable
(not supplied)
Scart
(EURO-AV)
LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2
LINE-1 (EURO AV)
AERIAL IN
Aerial cable (supplied)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Setting PAY-TV/Canal Plus channels
To watch or record PAY-TV/Canal Plus programmes, set your VCR to receive the
channels using the on-screen display.
In order to set the channels correctly, be sure to follow all of the steps below.
Before you start…
• Turn on the VCR, the TV, and the decoder.
• Set the TV to the video channel.
continued
Setting the PAY-TV/Canal Plus decoder
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Press MENU, then press M/m/</
, to highlight INSTALLATION
and press OK.
MENU
1
2
3
4
5
AUTO SET UP
MANUAL SET UP
SMARTLINK
VCR OUTPUT CH
: 3 2
OK
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press M/m to highlight MANUAL
SET UP, then press ,.
TV STATION TABLE
OK
OK
OK
OK
PR
1
2
3
4
CH
NAME
A A B –
L MN–
CDE –
DEC
0 2 7
0 2 9
0 3 0
0 3 2
0 3 3
OFF
OFF
OFF
OFF
OFF
I
J K –
5
– – – –
SWAPPING : OK
EXIT : MENU
DELETE : CLEAR
Press M/m to highlight the row
which you want to set for the
decoder, then press ,.
To display positions 6 to 80, press
M/m repeatedly.
MANUAL TUNING
PR
CH
MFT
DECODER
NAME
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press M/m to highlight DECODER.
MANUAL TUNING
PR
CH
MFT
DECODER
NAME
:
:
:
:
:
5
0 3 3
–
OFF
– – – –
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press , to set DECODER to ON,
then press OK.
MANUAL TUNING
PR
CH
MFT
DECODER
NAME
:
:
:
:
:
5
0 3 3
–
ON
– – – –
SELECT
END
:
SET
EXIT : MENU
:
: OK
Setting the PAY-TV/Canal Plus decoder
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Press MENU to exit the menu.
MENU
6
Notes
• To superimpose subtitles while watching PAY-TV/Canal Plus programmes, make
both decoder-VCR and VCR-TV connections using 21-pin Scart cables that are
compatible with the RGB signals. You cannot record subtitles on the VCR.
• When you watch PAY-TV/Canal Plus programmes through the RFU input of the
TV, press t TV/VIDEO so that the VIDEO indicator appears in the display
window.
*1 SLV-SE840D/E
*2 SLV-SE747E, SE740D/E, SX740D/E, SE640D/E and SE240D
Setting the PAY-TV/Canal Plus decoder
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Playing a tape
Before you start...
Turn on your TV and set it to the video channel.
1
Insert a tape.
2
The VCR turns on and starts playing
automatically if you insert a tape with
its safety tab removed.
Press H (play).
3
When the tape reaches the end, it will rewind automatically.
OK
Additional tasks
To
Do this
Stop play
Press x (stop)
Pause play
Press X (pause)
Resume play after pause
Fast-forward the tape
Rewind the tape
Eject the tape
Press X (pause) or H (play)
Press M (fast-forward) during stop
Press m (rewind) during stop
Press Z (eject)
Playing a tape
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Dial
Using Playback Dial on the
VCR
With Playback Dial, you can operate
the following playback options.
To
Do this
Resume play after pause
Fast-forward the tape
Press H (play)
Quickly turn and release Playback Dial to the right
(M (fast-forward)) during stop
Rewind the tape
Quickly turn and release Playback Dial to the left
(m (rewind)) during stop
Note
• Do not turn Playback Dial forcibly. It may damage Playback Dial.
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The
counter in the display window resets to “0:00:00” or “00:00.” Search for the
point afterwards by referring to the counter.
SE840D/E, SE747E, SE740D/E,
SE640D/E, SE240D
SX740D/E
Hour Minute Second
Hour
Minute
To display the counter on the TV screen, press
DISPLAY.
Notes
• The counter resets to “0:00:00” or “00:00” whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.
• Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
–The picture becomes black and white.
–The picture shakes.
–No picture appears on the TV screen.
–Black streaks appear horizontally on the TV screen.
–The colour density increases or decreases.
• Tapes recorded in the LP mode cannot be played back on SLV-SE240D.
• While setting the menu on the TV screen, buttons for playback on the remote
commander do not function.
continued
Playing a tape
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting playback automatically with one button (One
Touch Play) (not available on SLV-SE640D/E and SE240D)
If you use the SMARTLINK connection, you can turn on the TV, set the TV
to the video channel, and start playback automatically with one button.
1 Insert a tape.
The VCR automatically turns on.
If you insert a tape with its safety tab removed, the TV turns on and
switches to the video channel. Playback starts automatically.
2 Press H (play).
The TV turns on and switches to the video channel automatically.
Playback starts.
Tip
• When there already is a tape in the VCR, press ?/1 to turn on the VCR first. When
you press H (play), the TV turns on, the TV is set to the video channel, and
playback starts automatically in one sequence.
Note
• When you use the One Touch Play function, leave the TV on or in the standby
mode.
Playing a tape
40
Download from Www.Somanuals.com. All Manuals Search And Download.
REC
Press z REC to start recording.
5
The recording indicator lights up in the display window.
SE840D/E, SE747E, SE740D/E,
SX740D/E
Recording indicator
SE640D/E, SE240D
Recording indicator
To stop recording
Press x (stop).
To check the remaining time
Press
DISPLAY twice. With the display on, press COUNTER/REMAIN
to check the remaining time. Each time you press COUNTER/REMAIN,
the time counter and the remaining time appear alternately.
REMAIN
0 : 0 0 : 2 2
1 : 4 6
Time counter
Remaining time
In order to get an accurate remaining time indication, be sure TAPE
SELECT in the USER SET menu is set according to the tape type you use
To watch another TV programme while recording
Press t TV/VIDEO to turn off the VIDEO indicator in the display
window.
1
2 Select another programme position on the TV.
Recording TV programmes
42
Download from Www.Somanuals.com. All Manuals Search And Download.
To save a recording
To prevent accidental erasure, break off the
safety tab as illustrated. To record on the
same tape again, cover the tab hole with
adhesive tape.
Safety tab
Tips
• To select a programme position, you can use the programme number buttons on the
remote commander. For two-digit numbers, press -/-- (ten’s digit) followed by the
programme number buttons.
• If you connect additional equipment to a LINE connector or jack, you can select
the input signal using the INPUT SELECT or PROG +/– buttons.
• The
DISPLAY information appears on the TV screen indicating information
about the tape, but the information will not be recorded on the tape.
• If you do not want to watch TV while recording, you can turn off the TV. When
using a decoder, make sure to leave it on.
Notes
• The
DISPLAY information does not appear during still (pause) mode or slow-
motion playback.
• If a tape has portions recorded in both PAL and NTSC systems, the time counter
reading will not be correct. This discrepancy is due to the difference between the
counting cycles of the two video systems.
• You cannot watch a PAY-TV/Canal Plus programme while recording another PAY-
TV/Canal Plus programme.
• When you insert a non-standard commercially available tape, the remaining time
may not be correct.
• The remaining time is intended for rough measurement only.
• About 30 seconds after the tape begins playback, the tape remaining time will be
displayed.
* not available on SLV-SE240D
continued
Recording TV programmes
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording what you are watching on the TV (TV Direct
Rec) (not available on SLV-SE640D/E and SE240D)
If you use the SMARTLINK connection, you can easily record what you are
watching on the TV (other than tapes being played on the VCR).
1 Press ?/1 to turn on the VCR.
2 Insert a tape with its safety tab in place.
Press z REC while you are watching a TV programme or external
source.
3
The TV indicator lights up and the VCR starts recording what you are
watching on the TV.
Tip
• The TV indicator appears in the display window after you press z REC in some
situations such as:
–when you are watching a source connected to the TV’s line input, or
–when the TV tuner preset data for the programme position is different from the
data in the VCR tuner preset.
Notes
• You cannot record what you are watching using this method when the VCR is in
the following modes; pause, timer standby, tuner preset, Auto Set Up, and
recording.
• When the TV indicator is lit in the display window, do not turn off the TV nor
change the TV programme position. When the TV indicator is not lit, the VCR
continues recording the programme even if you change the TV programme
position on the TV.
• To use the TV Direct Rec function, select SMARTLINK in the INSTALLATION
menu, then set TV DIRECT RECORD to ON.
Recording TV programmes
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the Dial
Timer (SLV-SE840D/E only)
The Dial Timer function allows you to
make timer recordings of programmes
without turning on your TV. Set the
recording timer to record up to eight
programmes, including settings made with
other timer methods, that will be broadcast
within the next month. The recording start
time and recording stop time can be set at
one minute intervals.
?/1
DIAL TIMER X
x
PROGRAM +/–
Before you start...
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a decoder, turn it on.
DIAL TIMER
Press DIAL TIMER.
1
“DATE” and “TODAY” appear alternately in the display window.
If the date and time are not set, “DAY” will appear. See step 2 in the
DIAL TIMER
Turn
DIAL TIMER to set the recording date.
2
continued
Recording TV programmes using the Dial Timer (SLV-SE840D/E only)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAL TIMER
Press
DIAL TIMER.
3
“START” and the current time appear alternately in the display
window.
DIAL TIMER
PROGRAM
Turn
DIAL TIMER to set the recording start time.
4
5
You can set the recording start time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/–
buttons.
DIAL TIMER
Press
DIAL TIMER.
“STOP” and the recording stop time alternately appear in the
display window.
DIAL TIMER
PROGRAM
Turn
DIAL TIMER to set the recording stop time.
6
You can set the recording stop time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/–
buttons.
Recording TV programmes using the Dial Timer (SLV-SE840D/E only)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAL TIMER
Press
DIAL TIMER.
7
8
The programme position or LINE input appears in the display
window.
DIAL TIMER
Turn
DIAL TIMER to set the programme position.
INPUT SELECT
DIAL TIMER
To record from a decoder or other source connected to one or more
of the LINE inputs, turn DIAL TIMER or press INPUT SELECT
to display the connected line in the display window.
Press
“OK” appears in the display window for about five seconds.
The indicator appears in the display window and the VCR stands
DIAL TIMER to complete the setting.
9
by for recording.
To record from a decoder or other source, leave the connected
equipment switched on.
To return to the previous step
To return to the previous step, press the PROGRAM + and – buttons on the
VCR at the same time during any of the Dial Timer settings.
To stop recording
To stop the VCR while recording, press x (stop).
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The
indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
continued
Recording TV programmes using the Dial Timer (SLV-SE840D/E only)
Download from Www.Somanuals.com. All Manuals Search And Download.
47
To set the clock
Hold down
DIAL TIMER so that “DAY” appears in the display
1
window. However, if the clock has already been set, the current setting
appears.
DIAL TIMER to set the day.
2 Turn
3
4
Press
DIAL TIMER.
“MONTH” appears in the display window.
Turn and press
DIAL TIMER to set the month, and then the year.
After you set the year, “CLOCK” appears in the display window again.
DIAL TIMER to set the hour and minute.
5 Turn and press
When you have finished setting the time, press
DIAL TIMER to start
6
the clock.
Tips
• To cancel a Dial Timer setting, press x (stop) on the VCR while you are making
the setting.
• The programme is recorded in the current tape speed mode. To change the tape
speed, press SP/LP before you complete the setting in step 9.
Notes
• If eight programmes have already been set using the ShowView system or the
TIMER PROGRAMMING menu, “FULL” appears in the display window for
about five seconds.
• The
and
indicators flash in the display window when you complete the
setting in step 9 with no tape inserted.
• If you set the clock using the Auto Clock Set function and AUTO CLOCK is set to
ON, the clock will adjust itself to the incoming time signal regardless of
adjustments made with the Dial Timer. Be sure you have set the Auto Clock Set
correctly.
• When the time is set incorrectly, “ERROR” appears in the display window in step
9. Set the timer again from step 1.
• You cannot set the tape speed to AUTO using the Dial Timer. To select AUTO, set
the tape speed in the TIMER PROGRAMMING menu (see page 62).
Recording TV programmes using the Dial Timer (SLV-SE840D/E only)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Demonstration Mode
The Dial Timer function has a Demonstration Mode that allows the user, such as a
salesperson, to enter more than eight examples of timer settings when demonstrating
the use of the Dial Timer. It cancels the “FULL” notice which appears if eight
programmes have already been set. Do not use the Demonstration Mode for making
timer recordings. Doing so may cause the settings to be inaccurate.
To activate the Demonstration Mode
Press X (pause) on the VCR while turning the
DIAL TIMER. “DEMO”
appears in the display window for a few seconds.
To cancel the Demonstration Mode
Turn the power off and unplug the mains lead. Although the Demonstration
Mode is cancelled, the timer settings entered while using the Demonstration
Mode will remain. Be sure to manually cancel the timer settings before you
use the Dial Timer or any other timer method after reconnecting the mains
Recording TV programmes using the Dial Timer (SLV-SE840D/E only)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the
ShowView® system (not available on SLV-
SE640D/E and SE240D)
The ShowView system is the feature that simplifies programming the VCR to make
timer recordings. Just enter the ShowView number listed in the TV programme guide.
The date, times, and programme position of that programme are set automatically.
You can preset a total of eight programmes, including settings made with other timer
methods.
Before you start…
• Check that the VCR clock is set to the correct time and date.
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a decoder, turn it on.
• Turn on your TV and set it to the video channel.
• Set TIMER METHOD to SHOWVIEW or VARIABLE in the EASY OPERATION menu
Press TIMER.
1
TIMER
• When you set TIMER METHOD
TIMER METHOD
to VARIABLE:
The TIMER METHOD menu
appears on the TV screen. Press
STANDARD
SHOWVIEW
M/m to select SHOWVIEW, then
press OK.
OK
SELECT
SET
:
: OK
EXIT : MENU
• When you set TIMER METHOD
to SHOWVIEW:
The SHOWVIEW menu appears
on the TV screen.
SHOWVIEW
CODE – – – – – – – – –
CODE : 0 – 9
SET : OK
EXIT : MENU
Recording TV programmes using the ShowView® system (not available on SLV-SE640D/E and SE240D)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the programme number
buttons to enter the ShowView
number.
1
4
7
2
5
8
0
3
6
9
2
3
SHOWVIEW
CODE 1 2 3 4 – – – – –
If you make a mistake, press
CLEAR and re-enter the correct
number.
CLEAR
CODE : 0 – 9
SET : OK
EXIT : MENU
Press OK.
PR DAY
START
STOP
V/P
–
–
–
–
–
–
–
–
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
SP
The date, start and stop times,
programme position, tape speed and
VPS/PDC setting appear on the TV
screen.
OK
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
INPUT SELECT
CLEAR
• If “– –” appears in the “PR”
(programme) column (this may
happen for local broadcasts), you
SELECT
END
:
SET
:
: OK
EXIT : MENU
have to set the appropriate programme position manually.
Press M/m to select the desired programme position.
• To record from a decoder or other source connected to one or
more of the LINE inputs, press INPUT SELECT to display the
connected line in the “PR” position.
You will only have to do this operation once for the referred
channel. The VCR will then store your setting.
If the information is incorrect, press CLEAR to cancel the setting.
If you want to change the date, tape
speed and the VPS/PDC setting:
4
5
PR DAY
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
START
STOP
V/P
ON
SP
OK
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
–
–
–
–
–
–
–
1 Press </, to select the item
you want to change.
2 Press M/m to reset it.
• To record the same programme
every day or the same day every
• To use the VPS/PDC function, set V/P to ON. For details about
the VPS/PDC function, see “Timer recording with VPS/PDC
SELECT
END
:
SET
:
: OK
EXIT : MENU
Press MENU to exit the menu.
MENU
continued
Recording TV programmes using the ShowView® system (not available on SLV-SE640D/E and SE240D)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ?/1 to turn off the VCR.
6
The indicator appears in the display window and the VCR stands
by for recording.
To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press x (stop).
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press
m, the indication changes as shown below. Press M to change the indication
in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
Timer recording with VPS/PDC signals
Some broadcast systems transmit VPS (Video Programme System) or PDC
(Programme Delivery Control) signals with their TV programmes. These
signals ensure that your timer recordings are made regardless of broadcast
delays, early starts, or broadcast interruptions.
To use the VPS/PDC function, set V/P to ON in step 4 above. You can also
use the VPS/PDC function for a source connected to one or more of the
LINE inputs.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
Recording TV programmes using the ShowView® system (not available on SLV-SE640D/E and SE240D)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the Auto Tape Speed function*
In step 4 above, press m to select AUTO. When you are recording a
programme in the SP mode and the remaining tape length becomes shorter
than the recording time, the recording tape speed is automatically changed to
the LP mode. Note that some noise will appear on the picture when the tape
speed is changed. To operate this function correctly, the “TAPE SELECT”
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• You can set the extended time for the ShowView setting by 10, 20, 30, 40, 50, or 60
minutes. Set SHOWVIEW EXTEND in the EASY OPERATION menu to the
Notes
• If the VPS/PDC signal is too weak or the broadcasting station failed to transmit
VPS/PDC signals, the VCR will start recording at the set time without using the
VPS/PDC function.
• The
and
indicators flash in the display window when you press ?/1 with
no tape inserted.
• When you set TIMER METHOD to STANDARD in the EASY OPERATION
menu, the SHOWVIEW menu does not appear on the TV screen. Select
SHOWVIEW or VARIABLE.
* not available on SLV-SE240D
Recording TV programmes using the ShowView® system (not available on SLV-SE640D/E and SE240D)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording TV programmes using the timer
You can preset a total of eight programmes, including settings made with other timer
methods.
Before you start…
• Check that the VCR clock is set to the correct time and date.
• Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording
time.
• To record from a decoder, turn it on.
• Turn on your TV and set it to the video channel.
• Set TIMER METHOD*1 to STANDARD or VARIABLE in the EASY OPERATION menu
Press TIMER.
1
TIMER
For SLV-SE640D/E and SE240D
The TIMER PROGRAMMING
menu appears on the TV screen.
PR DAY
START
STOP
V/P
–
–
–
–
–
–
–
–
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
OK
SELECT
END
:
SET
EXIT : MENU
:
: OK
For SLV-SE840D/E, SE747E,
SE740D/E and SX740D/E
• When you set TIMER METHOD
to VARIABLE:
The TIMER METHOD menu
appears on the TV screen. Press
M/m to select STANDARD, then
press OK.
TIMER METHOD
STANDARD
SHOWVIEW
SELECT
:
SET
: OK
EXIT : MENU
• When you set TIMER METHOD
to STANDARD:
The TIMER PROGRAMMING
PR DAY
START
STOP
V/P
–
–
–
–
–
–
–
–
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
menu appears on the TV screen.
SELECT
END
:
SET
:
: OK
EXIT : MENU
Recording TV programmes using the timer
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the date, start and stop times,
programme position, tape speed and
VPS/PDC function* :
2
PR DAY
START
STOP
V/P
–
–
–
–
–
–
–
–
3 5 – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
2
OK
1 Press , to select each item in
turn.
2 Press M/m to set each item.
To correct a setting, press < to
return to that setting and reset.
INPUT SELECT
SELECT
END
:
SET
:
: OK
EXIT : MENU
• To record the same programme every day or the same day every
• To use the VPS/PDC function*2, set V/P to ON. For details about
the VPS/PDC function, see “Timer recording with VPS/PDC
• To record from a decoder or other source connected to one or
more of the LINE inputs, press INPUT SELECT to display the
connected line in the “PR” position.
Press MENU to exit the menu.
3
4
MENU
Press ?/1 to turn off the VCR.
The indicator appears in the display window and the VCR stands
by for recording.
To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press x (stop).
Daily/weekly recording
In step 2 above, press m to select the recording pattern. Each time you press
m, the indication changes as shown below. Press M to change the indication
in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
continued
Recording TV programmes using the timer
55
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The
indicator
turns off and the VCR switches on. Remember to press ?/1 to reset the VCR
to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
To use the Auto Tape Speed function*3
In step 2 above, press m to select AUTO. When you are recording a
programme in the SP mode and the remaining tape length becomes shorter
than the recording time, the recording tape speed is automatically changed to
the LP mode. Note that some noise will appear on the picture when the tape
speed is changed. To operate this function correctly, the “TAPE SELECT”
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• Even if you set TIMER METHOD*1 to SHOWVIEW in the EASY OPERATION
menu, you can set the timer manually. Press MENU to select TIMER
PROGRAMMING, then go to step 2.
Notes
• When setting the timer with VPS/PDC*2 signals, enter the start and stop times
exactly as indicated in the TV programme guide. Otherwise, the VPS/PDC
function will not work.
• If the VPS/PDC*2 signal is too weak or the broadcasting station failed to transmit
VPS/PDC signals, the VCR will start recording at the set time without using the
VPS/PDC function.
• The
and
indicators flash in the display window when you press ?/1 with
no tape inserted.
• The VPS/PDC function*2 is automatically set to off for the timer recording of a
satellite programme.
*1 not available on SLV-SE640D/E and SE240D
*2 not available on SLV-SE640D/E
*3 not available on SLV-SE240D
Recording TV programmes using the timer
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operations
Playing/searching at various speeds
Before you start…
Playback options
To
Do this
View the picture during
fast-forward or rewind
During fast-forward, hold down M (fast-forward).
During rewind, hold down m (rewind).
Play at high speed
• During playback, briefly press M (fast-forward)
or m (rewind). The tape continues to play at high
speed.
• During playback, hold down M (fast-forward) or
m (rewind). When you release the button, normal
playback resumes.
Play at twice the normal
speed
During playback, press ×2.
Play in slow motion
During playback, press y SLOW.
To resume normal playback
Press H (play).
continued
Playing/searching at various speeds
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Playback Dial on the
VCR
Playback Dial
With Playback Dial, you can
operate the following playback
options.
To
Do this
View the picture during
fast-forward or rewind
During fast-forward, turn and hold Playback Dial to
the right (M (fast-forward)). During rewind, turn
and hold Playback Dial to the left (m (rewind)).
Play at high speed
• During playback, quickly turn and release Playback
Dial to the right ( M (fast-forward)) or left (m
(rewind)). The tape continues to play at high speed.
• During playback, turn and hold Playback Dial to the
right (M (fast-forward)) or left (m (rewind)).
When you release Playback Dial, normal playback
resumes.
Tip
• Adjust the picture using the PROGRAM +/– buttons on the VCR if:
–Streaks appear while playing in slow motion.
–Bands appear at the top or bottom while pausing.
–The picture shakes while pausing.
To set tracking to the centre position, press both buttons (+/–) at the same time.
Notes
• The sound is muted during these operations.
• In the LP mode, noise may appear or there may be no colour.
• If the playback mode mark does not appear on the TV screen, press
• The picture may show noise when playing at high speed in reverse.
• Do not turn Playback Dial forcibly. It may damage Playback Dial.
DISPLAY.
Playing/searching at various speeds
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the recording duration time
After you have started recording in the normal way, you can have the VCR stop
recording automatically after a specified duration.
Before you start…
1 While recording, press z REC.
The indicator appears in the display window.
2 Press z REC repeatedly to set the duration time.
In SP mode
Each press advances the time in increments of 30 minutes.
0:30
1:00
4:00
4:30
Normal recording
In LP mode
Each press advances the time as shown below.
Normal recording
0:30
1:00
8:00
9:00
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the indicator disappears and the VCR
returns to the normal recording mode.
To stop recording
To stop the VCR while recording, press x (stop).
Note
• You cannot display the current tape time in the display window when setting the
recording duration time.
Setting the recording duration time
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronized Recording
(not available on SLV-SE640D/E and SE240D)
You can set the VCR to automatically record programmes from equipment
such as a satellite tuner by connecting the equipment to the LINE-3 (DEC/
EXT)*1 (or LINE-2 (DEC/EXT)*2) connector. The connected equipment
must have a timer function for this feature to work.
When the connected equipment turns on, the VCR also automatically turns
on and starts recording a programme from LINE-3 (DEC/EXT)*1 (or LINE-
2 (DEC/EXT)*2).
How to connect for Synchronized Recording
Connect the LINE-3 (DEC/EXT)*1 (or LINE-2 (DEC/EXT)*2) connector of
the VCR to the TV Scart connector of the satellite tuner. Then connect the
LINE-1 (EURO AV) connector to the TV.
Scart cable (not supplied)
Satellite tuner, etc.
LINE-3 (DEC/EXT)*1
or LINE-2 (DEC/EXT)*2
TV Scart
connector
LINE-1 (EURO AV)
Scart cable (not supplied)
Scart (EURO-AV)
: Signal flow
Synchronized Recording (not available on SLV-SE640D/E and SE240D)
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording programmes using
the Synchronized Recording
function
SYNCHRO REC button/indicator
Before you start...
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• Refer to “Index to parts and controls” for
button locations.
Press INPUT SELECT or PROG +/– to display “L3*1 (or L2*2)” in the
display window.
Set the timer on the connected equipment to the time of the programme
you want to record, then turn it off.
1
2
3 Press SP/LP to select the tape speed.
4 Hold down SYNCHRO REC on the VCR for more than two seconds.
The SYNCHRO REC indicator lights up in red and the VCR stands by
for recording.
The VCR automatically turns on and starts recording when it receives an
input signal from the connected equipment.
The VCR automatically stops recording when the tape reaches the end or
when the connected equipment stops transmitting an input signal.
To cancel the Synchronized Recording function
Press SYNCHRO REC on the VCR. The SYNCHRO REC indicator
disappears.
To stop recording
Press x (stop) while recording.
Notes
• This function may not work with some types of satellite tuners.
• Some TVs or other equipment with timer functions will automatically turn off if no
operation is performed within a certain amount of time. In this case, the
Synchronized Recording also stops automatically.
• When the connected equipment turns on while the SYNCHRO REC indicator
lights up in red, recording starts automatically.
• If the settings for timer recording and Synchronized Recording overlap, the
programme that starts first has priority and the second programme starts recording
only after the first programme has finished.
• The Auto Clock Set function does not work while the VCR stands by for
Synchronized Recording.
*1 SLV-SE840D/E
*2 SLV-SE747E, SE740D/E and SX740D/E
Synchronized Recording (not available on SLV-SE640D/E and SE240D)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking/changing/cancelling timer
settings
Before you start…
• Turn on your TV and set it to the video channel.
1 Press ?/1 to turn on the VCR.
Press MENU, then press M/m to highlight TIMER PROGRAMMING
and press OK.
2
• If you want to change or cancel a
PR DAY
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
2 9 S A 2 9 2 1 : 0 0 2 1 : 3 0 –
3 0 S A 1 2 : 0 0 1 3 : 3 0 –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
START
STOP
V/P
ON
setting, go on to the next step.
• If you do not need to change or cancel
the settings, press MENU, then turn
off the VCR to return to recording
standby.
SP
–
–
–
–
–
–
–
6
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to select the setting you want
3
PR DAY
START
STOP
V/P
ON
to change or cancel, then press ,.
3 5 S A 2 9 1 9 : 0 0 2 0 : 0 0
2 9 S A 2 9 2 1 : 0 0 2 1 : 3 0 –
3 0 S A 1 2 : 0 0 1 3 : 3 0 –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
– – – – – – – – : – – – – : – – –
SP
–
–
–
–
–
–
–
The PR number on the selected row
flashes.
6
SELECT
END
:
SET
EXIT : MENU
:
: OK
4 • To change the setting, press </, to select the item you want to
change, then press M/m to reset it.
• To cancel the setting, press CLEAR.
5 Press MENU to exit the menu.
If any settings remain, turn off the VCR to return to recording standby.
Checking/changing/cancelling timer settings
62
Download from Www.Somanuals.com. All Manuals Search And Download.
When the timer settings overlap
The programme that starts first has priority and the second programme starts
recording only after the first programme has finished. If the programmes
start at the same time, the programme listed first in the menu has priority.
Programme 1
Programme 2
about 20 seconds
will be cut off
Programme 1
Programme 2
about 20 seconds will be cut off
Checking/changing/cancelling timer settings
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording stereo and bilingual
programmes (not available on SLV-SE240D)
In the ZWEITON (German stereo) system
This VCR automatically receives and records stereo and bilingual
programmes based on the ZWEITON system. When a stereo or bilingual
programme is received, the STEREO indicator appears in the display
window.
To select bilingual sound while recording
Press AUDIO MONITOR to select the sound you want.
To listen to
Main
On-screen display
MAIN
Display window
STEREO
Sub
SUB
STEREO
Main and sub
Standard sound*
MAIN/SUB
MONO
STEREO
STEREO
* Usually the main channel heard from both the left and right in bilingual
programmes
To select stereo programme while recording
To listen to
On-screen display
STEREO
LCH
Display window
STEREO
Stereo
Left channel
Right channel
Standard sound*
STEREO
RCH
STEREO
LCH + RCH
STEREO
* Usually the mixed sound of left and right channels in stereo programmes
In the NICAM system (SLV-SE840E, SE747E, SE740E,
SX740E and SE640E only)
This VCR receives and records stereo and bilingual programmes based on
the NICAM system (NICAM appears on the TV screen). When a stereo or
bilingual programme is received, the STEREO indicator appears in the
display window.
To record a NICAM programme, NICAM in the USER SET menu should be
Recording stereo and bilingual programmes (not available on SLV-SE240D)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
To select the sound while recording
Press AUDIO MONITOR to select the sound you want.
Stereo programmes
To listen to
Stereo
On-screen display
NICAM, STEREO
NICAM, LCH
Display window
STEREO
Left channel
Right channel
STEREO
NICAM, RCH
STEREO
Left and right channels* NICAM, LCH + RCH
* Usually the mixed sound of left and right channels
Bilingual programmes
STEREO
To listen to
Main
On-screen display
NICAM, MAIN
NICAM, SUB
Display window
STEREO
Sub
STEREO
Main and sub
Standard sound*
NICAM, MAIN/SUB
NICAM, MONO
STEREO
STEREO
* Usually the main sound (monaural)
Selecting the sound during Hi-fi playback
Press AUDIO MONITOR to select the sound you want.
To listen to
Stereo
On-screen display
STEREO
LCH
Display window
STEREO
Left channel
Right channel
Mix sound*
Mono sound
STEREO
RCH
STEREO
MIX
STEREO
MONO
No indicator
* The mixed sound of left and right channels, and the normal mono audio track
continued
Recording stereo and bilingual programmes (not available on SLV-SE240D)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded
onto the main track along with the picture. Monaural sound is recorded onto
the normal audio track along the edge of the tape.
Stereo
Bilingual
Usually mixed
left/right channels
Usually main sound
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
• To listen to playback sounds in stereo, you must use the Scart or AUDIO OUT
connections.
• When you play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
Recording stereo and bilingual programmes (not available on SLV-SE240D)
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching using the index function
(not available on SLV-SE240D)
The VCR automatically marks the tape with an index signal at the point where each
recording begins. Use these signals as references to find a specific recording.
To find a specific recording by scanning (Index scan)
1 Insert an indexed tape into the VCR.
Press ./> (index search). The
2
VCR starts scanning each recording for
five seconds in the corresponding
INDEX SCAN : BB
direction.
3 Press H (play) to start playback when you find the desired point.
To search a specific recording (Index search)
1 Insert an indexed tape into the VCR.
2 Press ./> (index search) twice.
• To search ahead, press > (index
INDEX SEARCH : BB + 0 2
search) twice.
• To search backwards, press . (index
search) twice.
Press ./> (index search) depending on the direction where your
desired programme is located.
3
Each time you press the button, the number increases or decreases up to
±20, respectively.
The VCR starts searching, and playback starts automatically from that
point.
4
To stop searching
Press x (stop).
continued
Searching using the index function (not available on SLV-SE240D)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• No index signal will be added when recording starts from recording pause.
However, an index signal will be marked if you change the programme position
during recording pause.
• When you press . (index search), if there is nothing recorded before the
selected index signal, playback may not start exactly at the index signal.
Searching using the index function (not available on SLV-SE240D)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
Adjusting the tracking
Although the VCR automatically adjusts the
tracking when playing a tape, distortion may
occur if the recording is in poor condition. In
this case, manually adjust the tracking.
During playback, press PROGRAM +/– on
the VCR to display the tracking meter. The
distortion should disappear as you press one
of the two buttons. To resume automatic
tracking adjustments, eject the tape and re-
insert it.
TRACKING – – – – – – – – – – – –
Tracking meter
Adjusting the picture sharpness (Smart trilogic)
You can automatically adjust the sharpness of the picture.
During playback, press MENU, then press M/m/</, to highlight
1
2
USER SET and press OK.
Press M/m to highlight SMART
TRILOGIC, then press ,.
OSD
: ON
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
: E 1 8 0
: AUTO
: AUTO
: ON
POWER SAVE
SMART TRILOGIC
: OFF
: ON
SELECT
END
:
SET
EXIT : MENU
:
: OK
Press M/m to set SMART TRILOGIC to
ON or OFF.
3
PICTURE
• ON: Picture sharpness is automatically
adjusted.
SMART TRILOGIC : OFF
• OFF: Adjust the picture sharpness
manually.
To soften the picture, press <.
To sharpen the picture, press ,.
SOFTEN
SHARPEN
– – – – – – – – – – – – – – – – – – – – –
ON/OFF
END
:
SET
:
: OK
EXIT : MENU
4 Press MENU to return to the original screen.
Adjusting the picture
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Reducing the VCR’s power consumption
You can turn off the indicators in the display window when the VCR is off (standby
mode) to reduce the VCR’s power consumption.
Press MENU, then press M/m/</, to highlight USER SET and press
1
OK.
2 Press M/m to highlight POWER SAVE.
Press , to set to ECO1 or ECO2, then
3
press OK.
OSD
: ON
• ECO1: To reduce the power
consumption.
• ECO2: To reduce the power
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
POWER SAVE
SMART TRILOGIC
: E 1 8 0
: AUTO
: AUTO
: ON
: ECO1
: ON
consumption to a minimum.
SELECT
END
:
SET
:
: OK
EXIT : MENU
To turn on the indicators in the display window
Set POWER SAVE to OFF in step 3.
Notes
• When the VCR stands by for recording, the
indicator in the display window
remains lit even when POWER SAVE is set to ECO1 or ECO2.
• The Line Through function will not operate properly if POWER SAVE is set to
ECO2. Set POWER SAVE to OFF or ECO1 to ensure proper operation.
Reducing the VCR’s power consumption
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing menu options
Press MENU, then select USER SET or EASY OPERATION and press
OK.
1
OSD
: ON
VPS / PDC DEFAULT
SHOWVIEW EXTEND
AUTO POWER OFF
TIMER METHOD
: OFF
: OFF
: OFF
TAPE SELECT
COLOUR SYSTEM
FORMAT 1 6 : 9
NICAM
: E 1 8 0
: AUTO
: AUTO
: ON
: VARIABLE
POWER SAVE
SMART TRILOGIC
: OFF
: ON
SELECT
END
:
SET
EXIT : MENU
:
SELECT
END
:
SET
EXIT : MENU
:
: OK
: OK
2 Press M/m to select the option.
3 Press , to change the setting, then press OK.
Menu choices
Initial settings are indicated in bold print.
USER SET
Menu option
Set this option to
• ON to display the menu on the TV screen.
OSD
• OFF to disappear the menu from the TV screen.
TAPE SELECT
• E180 to use an E-180 or shorter type tape.
• E240 to use an E-240 type tape.
• E260 to use an E-260 type tape.
• E300 to use an E-300 type tape.
COLOUR SYSTEM • AUTO to select the colour system automatically.
• PAL to use the tape recorded in the PAL colour system.
• B/W to use the tape recorded in black and white.
• AUTO when you use a wide screen TV. The VCR
automatically detects if programmes being played back
or recorded are in normal or wide screen format.
• ON if the VCR cannot detect wide screen TV
programmes with AUTO. The VCR always plays back
and records in wide screen format.
FORMAT 16:9
• OFF if you are not using a wide screen TV.
NICAM*1
• ON to record NICAM broadcasts on the hi-fi audio
track.
• OFF to record standard sound on the hi-fi audio track.
continued
Changing menu options
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu option
Set this option to
POWER SAVE
• ECO1 to turn off the indicators in the display window to
conserve the VCR’s power.
• ECO2 to turn off the indicators in the display window
during standby mode to reduce the VCR’s power
consumption to a minimum. For using the Line Through
function and PAY-TV/Canal Plus function, select ECO1
or OFF.
• OFF to turn on the indicators in the display window
while the VCR is standing by.
SMART TRILOGIC • ON to automatically adjust the sharpness of the picture.
• OFF to manually adjust the sharpness of the picture.
EASY OPERATION
Menu option
Set this option to
VPS/PDC
• OFF to deactivate the VPS/PDC function.
• ON to activate it.
DEFAULT*2
SHOWVIEW
EXTEND*3
• OFF to deactivate the ShowView Extend function.
• 10/20/30/.../60 (minutes) to extend the time of the
ShowView setting by the selected amount of time.
AUTO POWER OFF • OFF to deactivate the Auto Power Off function.
• 2HOUR/3HOUR to turn the VCR off automatically if no
signal is received and you do not press any of the buttons
during this time.
TIMER METHOD*3
• VARIABLE to display the TIMER METHOD menu for
selecting STANDARD or SHOWVIEW when pressing
the
• STANDARD to display the TIMER PROGRAMMING
menu when pressing the TIMER button.
• SHOWVIEW to display the SHOWVIEW menu when
pressing the TIMER button.
TIMER button.
*1 SLV-SE840E, SE747E, SE740E, SX740E and SE640E only
*2 not available on SLV-SE640D/E
*3 not available on SLV-SE640D/E and SE240D
Changing menu options
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing
Connecting to a VCR or stereo system
How to connect to record on this VCR
Connect the line outputs of the other VCR to the input connector of this
VCR. Refer to the examples A through C and choose the connection that
best suits your VCR.
Example A
TV
Your VCR (Recorder)
LINE-1 (EURO AV)
Other VCR (Player)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Example B (SLV-SE840D/E only)
Your VCR (Recorder)
TV
t LINE-2 L o R
(open cover to connect)
LINE OUT
Audio/video cable (not supplied)
Other VCR (Player)
: Signal flow
continued
Connecting to a VCR or stereo system
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Example C
Your VCR (Recorder)
TV
LINE-3 (DEC/EXT)*1 or
LINE-2 (DEC/EXT)*2
Other VCR (Player)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
How to connect to a stereo system (SLV-SE840D/E only)
Connect the t LINE-2 L o R jacks on this VCR to the audio output jacks
on the stereo system, using an audio cable (not supplied).
Notes
• Make sure you connect the plugs to jacks of the same colour.
• If the other VCR is a monaural type, leave the red plugs unconnected.
• If you connect this VCR to both the LINE IN and LINE OUT jacks of the other
VCR, select the input correctly to prevent a humming noise.
• If the other VCR does not have a Scart (EURO-AV) connector, use an adequate
cable instead and connect the cable to the line out jacks of the other VCR.
• When you connect another VCR to the LINE-3 (DEC/EXT)*1 or LINE-2 (DEC/
EXT)*2 connector, press INPUT SELECT to display “L3”*1 or “L2”*2 in the
display window.
*1 SLV-SE840D/E
*2 SLV-SE747E, SE740D/E, SX740D/E, SE640D/E and SE240D
Connecting to a VCR or stereo system
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic editing
When recording on this VCR
Before you start editing
REC z
• Turn on your TV and set it to the video
channel.
• Press INPUT SELECT to display the
connected line in the display window.
• Press SP/LP to select the tape speed, SP or
LP*.
X
Insert a source tape with its safety tab removed into the other (playback)
VCR. Search for the point to start playback and set it to playback pause.
Insert a tape with its safety tab in place into this (recording) VCR.
Search for the point to start recording and press X (pause) to set it to
playback pause.
1
2
3 Press REC z on this VCR to set it to recording pause.
To start editing, press the X (pause) buttons on both VCRs at the same
time.
4
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X (pause) on this VCR when an
unwanted scene begins. When it ends, press X (pause) again to resume recording.
* not available on SLV-SE240D
Basic editing
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio dubbing (SLV-SE840D/E only)
This feature lets you record over the normal
AUDIO DUB
audio track. The monaural sound previously
recorded is replaced while the original hi-fi
sound remains unchanged. Use this feature
to add commentary to a tape that you have
recorded with a camcorder.
Before you start...
t LINE-2 L o R
X
• Open the t LINE-2 L o R jacks cover on the
front panel and connect a playback source.
• Turn on the TV and set it to the video channel.
Insert a source tape into your stereo system (or the playback VCR).
Search for the point to start playback and set it to playback pause.
Insert a prerecorded tape with its safety tab in place into this (recording)
VCR. Search for the start of the section to be replaced and press
X (pause).
1
2
The VCR enters pause mode.
3 Press AUDIO DUB.
“A_DUB” and the indicator appears in the display window.
To start editing, press the X (pause) buttons on this VCR and the stereo
system (or other VCR) at the same time.
4
After you use this feature, the audio in playback mode is automatically
set to monaural.
To stop editing
Press x (stop) on this VCR and the stereo system (or other VCR).
Audio dubbing (SLV-SE840D/E only)
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest
Sony service facility.
Symptom
Remedy
The ?/1 (on/standby)
• Connect the mains lead to the mains securely.
switch does not function.
The power is turned on
but the VCR does not
operate.
• Moisture condensation has occurred. Turn the power off,
unplug the mains lead and leave the VCR to dry for over
three hours.
The VCR is plugged in
but the display window
remains dark.
page 70).
The clock has stopped
and “– –:– –” appears in
the display window.
• The clock stops if the VCR is disconnected from the mains.
Reset the clock (and timer).
The playback picture
does not appear on the
TV screen.
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
• If the VCR is connected to the TV with the Scart cable,
make sure the VIDEO indicator is lit in the display
window. Use the t TV/VIDEO button on the remote
commander to light up the VIDEO indicator.
The picture is not clear.
• Existing broadcasts may interfere with the VCR. Reset the
• Adjust the tracking with the PROGRAM +/– buttons on the
VCR.
• The video heads are dirty (see the last page of
Troubleshooting). Clean the video heads using a Sony
video head cleaning cassette. If a Sony cleaning cassette is
not available in your area, have the heads cleaned at your
nearest Sony service facility (a standard service charge will
be required). Do not use a commercially available liquid
type cleaning cassette other than Sony’s, as it may damage
the video heads.
• The video heads may have to be replaced. Consult your
local Sony service facility for more information.
The picture rolls
vertically during picture
search.
• Adjust the vertical hold control on the TV or monitor.
The picture has no
sound.
• The tape is defective.
• If you made A/V connections, check the audio cable
connection.
continued
Troubleshooting
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The sound from a tape
recorded with the VCR is
not in stereo or the
STEREO indicator in the
display window is
flashing.
• Adjust the tracking.
• The video heads are dirty. Clean the video heads using a
Sony video head cleaning cassette as explained above.
No TV programme
appears on the TV
screen.
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
• Existing broadcasts may interfere with the VCR. Reset the
• Select the correct source with the INPUT SELECT button.
Select a programme position when recording TV
programmes; select a line input when recording from other
equipment.
TV reception is poor.
• Make sure the aerial cable is connected securely.
• Adjust the TV aerial.
The tape starts playing as • The safety tab has been removed. To record on this tape,
The tape is ejected when • The safety tab has been removed. To record on this tape,
you press z REC.
Nothing happens when
• Make sure the tape is not at its end.
you press z REC.
The timer does not
operate.
• Check that the clock is set.
• Make sure a tape has been inserted.
• Check that the safety tab has not been removed.
• Make sure the tape is not at its end.
• Make sure a programme has been set for timer recording.
• Make sure your timer settings are past the current time.
• Check that the decoder is turned on.
• Check that the satellite tuner is turned on.
• The clock stops if the VCR is disconnected from the mains.
Reset the clock and timer.
• Turn the power off and unplug the mains lead.
The SHOWVIEW menu • Check that TIMER METHOD in the EASY OPERATION
or the TIMER
PROGRAMMING menu
does not appear.
Troubleshooting
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The VPS/PDC function
does not operate
properly.
• Check that the clock and the date are set correctly.
• Check that the VPS/PDC time you set is the correct one
(there might be a mistake in the TV programme guide). If
the broadcast you wanted to record did not send the good
VPS/PDC information, the VCR will not start recording.
• If the reception is poor, the VPS/PDC signal might be
altered and the VCR might not start recording.
The SYNCHRO REC
button turns off while
recording or does not go
back to recording
• The tape has reached its end. Insert a new tape and press
SYNCHRO REC again.
standby mode.
The Synchronized
Recording function does
not work.
• The connected equipment was not turned off.
Turn off the connected equipment and press SYNCHRO
REC again.
• There was a power failure. Press SYNCHRO REC again.
The programme recorded • If the settings for timer recordings and Synchronized
with the Synchronized
Recording function is
incomplete.
Recording overlap, the programme that starts first has
priority and the second programme starts recording only
after the first programme has finished.
• There was a power failure. Press SYNCHRO REC again.
You cannot watch PAY-
TV/Canal Plus
• Check that DEC is set to ON for this channel in the TV
STATION TABLE menu.
programmes when the
VCR is in standby mode.
• Make sure the PAY-TV/Canal Plus Scart cable is plugged
securely.
A PAY-TV/Canal Plus
programme is always
recorded scrambled.
• Make sure the PAY-TV/Canal Plus Scart cable is plugged
securely.
• Check that DEC is set to ON for this channel in the TV
STATION TABLE menu.
continued
Troubleshooting
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
A tape cannot be
inserted.
• Check that a tape is not already in the tape compartment.
The remote commander • Make sure you are pointing the remote commander at the
does not function.
remote sensor on the VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the [TV] / [VIDEO] remote control switch is set
correctly.
The selected input line
connector number does
not appear in the display
window.
• Press INPUT SELECT to display the connected line.
The tracking meter does • The recording condition of the tape is very poor and
not appear on the TV
screen.
tracking cannot be adjusted.
You cannot control other • Set your TV’s code number. The code number may change
TVs.
when you replace the batteries of the remote commander.
The display window
becomes dim.
• The display window automatically becomes dim when the
VCR is in standby or timer recording mode.
The VCR needs to be
cleaned.
• Clean the cabinet, panel and controls with a dry, soft cloth,
or a soft cloth slightly moistened with a mild detergent
solution. Do not use any type of solvent, such as alcohol or
benzine.
The Line Through
function does not
operate.
page 70).
Symptoms caused by contaminated video heads
• No picture (or
black & white
• Normal picture
• Rough picture
• Unclear picture
screen appears)
initial
contamination
terminal
Troubleshooting
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Output impedance: less than 10 kilohms
*1 SLV-SE840D/E only
*2 not available on SLV-SE640D/E and
SE240D
System
Channel coverage
PAL (B/G)
VHF E2 to E12
General
Power requirements
VHF Italian channel A to H
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
RF output signal
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
220 – 240 V AC, 50 Hz
Power consumption
•SLV-SE240D
15 W
1.2 W (POWER SAVE is set to ECO2,
minimum)
•SLV-SE640D/E
17 W
1.2 W (POWER SAVE is set to ECO2,
minimum)
• SLV-SE840D/E, SE747E, SE740D/E
and SX740D/E
SP: PAL 23.39 mm/s (recording/
playback)
NTSC 33.35 mm/s (playback only)
LP: PAL 11.70 mm/s (recording/
playback)*
NTSC 16.67 mm/s (playback only)
EP: NTSC 11.12 mm/s (playback only)*
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Rewind time
Approx. 1 min. (with E180 tape)
* not available on SLV-SE240D
Inputs and outputs
LINE-1 (EURO AV)
17 W
1.3 W (POWER SAVE is set to ECO2,
minimum)
Operating temperature
5° C to 40° C
Storage temperature
–20° C to 60° C
Dimensions including projecting parts and
controls (w/h/d)
21-pin
Approx. 360 × 95 × 255 mm
(SLV-SE240D)
Video input: pin 20
Audio input: pins 2 and 6
Video output: pin 19
Approx. 430 × 96 × 255 mm
(SLV-SE840D/E, SE747E, SE740D/E,
SX740D/E and SE640D/E)
Mass
Audio output: pins 1 and 3
LINE-2 (DEC/EXT)/LINE-3 (DEC/EXT)
21-pin
Video input: pin 20
Approx. 2.8 kg (SLV-SE240D)
Approx. 3.1 kg (SLV-SE840D/E,
SE747E, SE740D/E, SX740D/E and
SE640D/E)
Audio input: pins 2 and 6
t LINE-2 L o R*1
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO IN, phono jack (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
AUDIO (OUT/SORTIE) R/D L/G*2
Phono jack (2)
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Design and specifications are subject to
change without notice.
Rated output level: 327 mVrms
Load impedance: 47 kilohms
Specifications
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
L
S
Adjusting
Language selection 26
LP mode 41
Safety tab 43
Scart connection 17
Searching
picture 69
tracking 69
Aerial hookup 16
Audio dubbing 76
Audio monitor 65
Audio track 66
Auto Clock Set 21
Auto Set Up 20
at various speeds 57
using the index function 67
ShowView
recording 50
Smart trilogic 69
SMARTLINK
NexTView Download 18
One Touch Menu 18
One Touch Timer 18
SP mode 41
M
Manual fine tuning 29
Monaural 65
N
NICAM broadcasts 64
Normal audio track 66
C
Canal Plus 35
Changing the programme
position 30
Changing the station name 33
Cleaning the video heads 77
Clock setting 23
O
Optional setting 71
Stereo 64
Syncronized Recording 61
P
PDC (Programme Delivery
Control) 52
Colour system
T
compatible colour systems
Connecting
Timer setting 54
Playback 38
cancelling 62
changing 62
checking 62
using the Dial Timer 45
using the ShowView
system 50
at various speeds 57
selecting the sound 65
slow motion 57
to a TV with a Scart
to video equipment 19
Counter 39
Power save 70
Preset download 25
Presetting channels 27
R
Country selection 21
Recording 41
V
bilingual programmes 64
duration time 59
saving 43
stereo programmes 64
timer setting 54
using the Dial Timer 45
using the ShowView
system 50
what you are watching on
the TV 44
D
VPS (Video Programme
System) 52
Demonstration 49
Dial Timer 45
Disabling the programme
positions 31
W
Wide screen format 71
Z
E
ZWEITON broadcasts 64
Editing 73
while watching another
programme 42
H
Hi-fi audio track 66
I
Index scan 67
Index search 67
Index
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
3... Press M/m/</, to select a language,
1 Connecting the VCR
then press OK.
4... When the COUNTRY SELECTION
menu appears, press M/m/</, to
select a country, then press OK.
When all of the receivable channels are
preset, the menu disappears from the TV
screen. You can rearrange the programme
position in any order (see “Changing/
1
LINE-1
(EURO AV)
4
3 Setting the clock
2
3
1... Press MENU, then press M/m/</, to
highlight CLOCK SET and press OK.
2... Press M/m to set the hour, then press ,.
3... Press M/m to set the minutes. Set the
day, month, and year in sequence by
pressing , to select the item to be set,
and press M/m to select the digits, then
press OK.
:Signal flow
1 ... Connect the aerial to of the VCR.
2 ... Connect and the aerial input of your
TV using the supplied aerial cable.
4... Press MENU.
3 ... For better picture and sound, connect
LINE-1 (EURO AV) to your TV using a
Scart cable if your TV has a Scart
(EURO-AV) connector.
Now you can operate your VCR.
4 ... Connect the mains lead to the mains.
2 Using the Auto Set Up function
1 ... Turn on your TV and set it to the video
channel.
If your TV does not have a Scart
(EURO-AV) connector, tune the TV to
channel 32 (the initial RF channel of this
VCR). Refer to your TV’s manual for
TV tuning instructions. If the picture
does not appear clearly, see “To change
2 ... Connect the mains lead to the mains.
Sony Corporation Printed in Indonesia
AC68-02164A
Download from Www.Somanuals.com. All Manuals Search And Download.
|