3-866-158-11 (2)
Vid e o Ca sse t t e
Re co rd e r
Operating Instructions
Ow ner’s record
The model and serial numbers are located at the rear of the
unit. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
SLV-469
©1999 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f co n t e n t s
Ge t t in g St a rt e d
4
5
6
Step 1: Unpacking
Step 2: Setting up the remote commander
Step 3: Hookups
16 Step 4: Setting the clock
18 Selecting a language
19 Presetting channels
Ba sic Op e ra t io n s
Ad d it io n a l In fo rm a t io n
25 Playing a tape
45 General setup information
47 Troubleshooting
49 Specifications
28 Recording TV programs
31 Recording TV programs using the
timer
50 Index to parts and controls
55 Index
Ad d it io n a l Op e ra t io n s
back cover
Quick reference to using the VCR
34 Playing/ searching at various
speeds
35 Searching for a selected point on
the tape
37 Skip-searching automatically
38 Recording TV programs using the
quick timer
39 Checking/ changing/ cancelling
timer settings
41 Adjusting the picture
42 Changing menu options
43 Editing with another VCR
3
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
St e p 1
Un p a ckin g
Check that you have received the following items with the VCR:
• Remote commander
• 75-ohm coaxial cable with F-type
connectors
• Size AA (R6) batteries
4
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 2
Se t t in g u p t h e re m o t e co m m a n d e r
In se rt in g t h e b a t t e rie s
Insert two size AA (R6) batteries by
matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Usin g t h e re m o t e co m m a n d e r
You can use this remote
Remote sensor
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with
a dot (• ) can be used to operate
your Sony TV.
TV / VIDEO
1
2
3
To operate
the VCR
Set TV / VIDEO to
VIDEO and point at the remote sensor on the VCR
TV and point at the remote sensor on the TV
a Sony TV
Notes
•
•
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
•
•
Do not use a new battery with an old one.
Do not use different types of batteries.
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
5
St e p 3
Ho o ku p s
Se le ct in g t h e b e st h o o ku p o p t io n
There are many ways in which your VCR can be hooked up. To hook up
your VCR so that it works best for you, first scan through the table below.
Then use the accompanying diagrams and procedures on the following
pages to set up your VCR.
If you have
Use
Refer to
TV that has audio/ video input
Audio/video (A/V) hookup, then Page 7
follow one of the hookups below.
Antenna only, no cable TV
Hookup 1
Hookup 2
Pages 8 and 9
Pages 10 and 11
Pages 12 and 13
Pages 14 and 15
Cable box with many scrambled
channels
No cable box or cable box with only a
few scrambled channels
Hookup 3
Hookup 4
Cable box with onlya few scrambled
channels, using an A/ B switch
After you’ve completed the connections, follow the instructions for setup.
During setup, if you need more details on the procedure described, page
numbers are provided where you can find complete, step-by-step
instructions.
After you’ve completed the setup, you’re ready to use your VCR.
Procedures differ depending on the hookup you used. For an overview,
refer to “Quick reference to using the VCR” on the back cover.
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are
completed.
• Be sure you make connections firmly. Loose connections may cause
picture distortion.
• If your TV doesn’t match any of the examples provided, see your nearest
Sony dealer or qualified technician.
6
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Au d io /vid e o (A/V) h o o ku p
Page 7
If your TV has audio/ video (A/ V) input jacks, you will get a better picture
and sound when you hook up your VCR using these connections. If your
TV doesn’t have A/ V inputs, see the following pages for antenna or cable
hookups.
If you’re not planning to use your VCR to record programs, you’re finished
setting up the VCR after you’ve made the connections shown on this page.
If you want to record off-air or off your cable TV system, complete these
connections first, and then go to the following pages for antenna or cable
hookups.
A Use this hookup if your TV has stereo jacks
VCR
TV
AUDIO VIDEO
LINE-1 IN
IN
LINE OUT
VIDEO
AUDIO
Audio/video cable (not supplied)
B Use this hookup if your TV doesn’t have stereo jacks
VCR
TV
AUDIO VIDEO
LINE-1 IN
LINE OUT
IN
VIDEO
AUDIO
Audio/video cable (not supplied)
Note
•
If you use the Trinitron TV Synchro Play function (see page 27), the A/ V connection
is necessary. (If your TV has two or more inputs, connect the audio/ video cable to
the VIDEO IN 1 jacks.)
Note to CATV system installer (in USA)
This reminder is provided to call the CATV system installer’s attention to Article 820-
40 of the NEC that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Getting Started
7
Download from Www.Somanuals.com. All Manuals Search And Download.
St e p 3: Ho o ku p s (co n t in u e d )
Pages 8 and 9
Ho o ku p 1
An t e n n a h o o ku p
Make the following connections if you’re using an antenna (if you don’t
have cable TV).
A Use this hookup if you’re using:
• VHF/ UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
Rear of TV
VHF/UHF
Match the type of
connector on your
TV: A, B, or C.
A
or
or
VHF
VCR
B
VHF/UHF
IN
UHF
VHF
OUT
C
UHF
B Use this hookup if you’re using a VHF-only antenna (you get
channels 2–13 only)
Rear of TV
VHF/UHF
A
Match the type of
connector on your
TV: A, B, or C.
or
or
VHF
VCR
B
For connector types
B and C, no UHF
connection is
VHF/UHF
IN
UHF
VHF
OUT
required.
C
UHF
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so you can connect the cable to the VHF/ UHF IN
connector. If you have separate cables for VHF and UHF antennas, you should use a
U/ V band mixer (not supplied). For details, see page 46.
8
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho o ku p 1: VCR se t u p
1
Set the RF UNIT switch to
RF UNIT
CH3 CH4
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 45. If you made A/ V connections (page 7), you
can skip this step.
2
Change the on-screen display language if desired. For details, see
page 18.
1 Press MENU and select LANGUAGE.
LANGUAGE
ENGLISH
ESPAÑOL
2 Select the language, and press OK.
3
4
Press MENU and select TUNER PRESET. Set
ANTENNA/ CABLE to ANT. For details, see
page 19.
TUNER PRESET
CH2
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
Preset the channels into the VCR. Select
AUTO PRESET and press OK.
TUNER PRESET
CH2
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLEASE WAIT
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
9
St e p 3: Ho o ku p s (co n t in u e d )
Pages 10 and 11
Ho o ku p 2
Ho o ku p 4
Ca b le b o x w it h m a n y scra m b le d ch a n n e ls
Recommended use
Use this hookup if your cable system scrambles all or most channels.
What you can do w ith this hookup
• Record any channel by selecting the channel on the cable box
What you can’t do
• Record one channel while watching another channel
Rear of TV
Cable box
Wall
VHF/UHF
IN
Match the type
of connector on
your TV: A, B, or
C.
A
OUT
or
or
VHF
For connector
types B and C, no
UHF connection
is required.
B
UHF
VHF
C
VCR
VHF/UHF
IN
UHF
OUT
10 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho o ku p 2: VCR se t u p
1
Set the RF UNIT switch to
RF UNIT
CH3 CH4
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 45. If you made A/ V connections (page 7), you
can skip this step.
2
3
Turn on your cable box.
Change the on-screen display language if desired. For details, see
page 18.
1 Press MENU and select LANGUAGE.
LANGUAGE
ENGLISH
ESPAÑOL
2 Select the language, and press OK.
4
5
Press MENU and select TUNER PRESET. Set
ANTENNA/ CABLE to ANT. For details, see
page 19.
TUNER PRESET
CH2
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
Preset the channels into the VCR. Select
AUTO PRESET and press OK.
TUNER PRESET
CH2
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLEASE WAIT
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
11
St e p 3: Ho o ku p s (co n t in u e d )
Pages 12 and 13
Ho o ku p 3
No ca b le b o x, o r ca b le b o x w it h o n ly a fe w
scra m b le d ch a n n e ls
Recommended use
Use this hookup if you do not have a cable box. Also use this hookup if your
cable system scrambles only a few channels.
What you can do w ith this hookup
• Record any unscrambled channel by selecting the channel on the VCR
What you can’t do
• Record scrambled channels that require a cable box
VCR
Rear of TV
VHF/UHF
Wall
VHF/UHF
IN
A Match the type
OUT
of connector
on your TV: A,
B, or C.
or
or
VHF
B
C
For connector
types B and C, no
UHF connection
is required.
UHF
VHF
Connect this cable
directly to your TV
if you don't have a
cable box.
Cable box
IN
OUT
UHF
12 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho o ku p 3: VCR se t u p
1
Set the RF UNIT switch to
RF UNIT
CH3 CH4
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 45. If you made A/ V connections (page 7), you
can skip this step.
2
3
Turn on your cable box.
Change the on-screen display language if desired. For details, see
page 18.
1 Press MENU and select LANGUAGE.
LANGUAGE
ENGLISH
ESPAÑOL
2 Select the language, and press OK.
4
5
Press MENU and select TUNER PRESET. Set
ANTENNA/ CABLE to CABLE. For details,
see page 19.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
Preset the channels into the VCR. Select
AUTO PRESET and press OK.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLEASE WAIT
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
13
St e p 3: Ho o ku p s (co n t in u e d )
Pages 14 and 15
Ho o ku p 4
Ca b le b o x w it h o n ly a fe w scra m b le d ch a n n e ls, u sin g
a n A/B sw it ch
Recommended use
By using an A/ B switch (not supplied), this hookup allows you to record
both scrambled and unscrambled channels conveniently.
What you can do w ith this hookup
• Record any unscrambled channel by selecting the channel directly on the
VCR (the A/ B switch is set to A)
• Record any scrambled channel by selecting the channel on the cable box
(the A/ B switch is set to B)
What you can’t do
• Record one scrambled channel while watching another channel (the A/ B
switch is set to B)
Rear of TV
Cable box
Wall
Splitter
VHF/UHF
A
IN
OUT
Match the type
of connector
on your TV: A,
B, or C.
or
or
VHF
B
A/B sw itch
For connector
types B and C,
no UHF
connection is
required.
A
B
UHF
VHF
C
VCR
VHF/UHF
IN
UHF
OUT
14 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho o ku p 4: VCR se t u p
1
Set the RF UNIT switch to
RF UNIT
CH3 CH4
CH3 or CH4, whichever
channel is not used in your
area. If both are used, set
the switch to either channel.
For details, see page 45. If you made A/ V connections (page 7), you can
skip this step.
2
3
Set the A/ B switch to “A.”
Change the on-screen display language if desired. For details, see
page 18.
1 Press MENU and select LANGUAGE.
LANGUAGE
ENGLISH
ESPAÑOL
2 Select the language, and press OK.
4
5
6
Press MENU and select TUNER PRESET. Set
ANTENNA/ CABLE to CABLE. For details,
see page 19.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
Preset the unscrambled channels into the
VCR. Select AUTO PRESET and press OK.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLEASE WAIT
Preset the cable box output channel (usually 2, 3 or 4). For details, see
page 21.
Cable box output channel
1 Press MENU and select TUNER PRESET.
TUNER PRESET
CH3
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
2 Enter the cable box output channel.
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
3 Set MANUAL SET to ADD and press OK.
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
15
St e p 4
1
4
7
2
5
8
0
3
6
9
Se t t in g t h e clo ck
Set the time and date to use the timer
feature for recording programs.
Before you start…
• Turn on the VCR and the TV.
• Set the TV to the VCR channel
(channel 3 or 4). If your TV is
connected to the VCR using A/ V
connections, set the TV to video input.
MENU
• Press TV/ VIDEO to display the
VIDEO indicator in the VCR’s display
window.
OK
>/./?//
• MENU
1
2
Press MENU, then press >/ .to move the
CLOCK SET
1 / 1 / 1998 TH 12 : 00
cursor (z) to CLOCK SET and press OK.
AM
PLAY
OK
Press >/ .to set the month.
CLOCK SET
11 / 1 / 1998 SU 12 : 00
PLAY
OK
AM
16 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press /to flash the day and press >/ .
to set the day.
CLOCK SET
PLAY
OK
11 / 16 / 1998 MO 12 : 00
AM
The day of the week is set automatically.
4
5
Set the year, hour, and minutes in the same way as the day.
PLAY
OK
Press OK to start the clock.
PLAY
OK
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Se le ct in g a
la n g u a g e
1
4
7
2
5
8
0
3
6
9
You can change the on-screen display
language.
MENU
OK
>/./?//
• MENU
1
2
Press MENU, then press >/ .to move the
LANGUAGE
cursor (z) to LANGUAGE and press OK.
ENGLISH
ESPAÑOL
PLAY
OK
Press >/ .to select ENGLISH or ESPAÑOL, then press OK.
PLAY
OK
18 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre se t t in g
ch a n n e ls
1
4
7
2
5
8
0
3
6
9
This VCR is capable of receiving VHF
channels 2 to 13, UHF channels 14 to 69
and unscrambled CATV channels 1 to
125. First, we recommend that you
preset the receivable channels in your
area using automatic presetting. Then, if
there are any unwanted channels,
disable them manually. If you have
decided which channels you wish to
preset, set them directly using manual
presetting.
MENU
Before you start…
• Turn on the VCR and the TV.
OK
• Set the TV to the VCR channel
(channel 3 or 4). If your TV is
connected to the VCR using A/ V
connections, set the TV to video
input.
>/./?//
• Press TV/ VIDEO to display the
VIDEO indicator in the VCR’s
display window.
Pre se t t in g a ll re ce iva b le ch a n n e ls a u t o m a t ica lly
• MENU
1
Press MENU, then press >/ .to move the
cursor (z) to TUNER PRESET and press
OK.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLAY
OK
2
Press >/ .to select ANTENNA/ CABLE.
PLAY
OK
continued
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Pre se t t in g ch a n n e ls (co n t in u e d )
TUNER PRESET
CH1
3
• To preset cable TV channels:
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
Press ?/ /to set ANTENNA/ CABLE to
CABLE.
• ADD ERASE
• ON OFF
PLAY
OK
FINE TUNING
• To preset VHF and UHF channels:
TUNER PRESET
CH2
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
Press ?/ /to set ANTENNA/ CABLE to
ANT.
PLAY
OK
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
4
Press >/ .to select AUTO PRESET, then
TUNER PRESET
CH2
press OK.
ANTENNA / CABLE • ANT CABLE
AUTO PRESET
MANUAL SET
AFT
PLAY
OK
• ADD ERASE
• ON OFF
All receivable channels are preset in
numerical sequence. When no more
receivable channels can be found,
presetting stops and the picture from the
lowest numbered channel is displayed on
the TV screen.
FINE TUNING
PLEASE WAIT
20 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre se t t in g /d isa b lin g
ch a n n e ls m a n u a lly
1
4
7
2
5
8
0
3
6
9
Number
buttons,
ENTER
CH +/–
MENU
OK
>/./?//
• MENU
1
Press MENU and select TUNER PRESET,
then press OK.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLAY
OK
continued
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Pre se t t in g ch a n n e ls (co n t in u e d )
Channel to be preset
2
• To preset a channel:
1
4
7
2
5
8
0
3
6
9
1 Press the number buttons to enter the
channel number, then press ENTER.
2 Press ?/ /to set MANUAL SET to
ADD.
TUNER PRESET
CH5
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
Channel to be disabled
• To disable a channel:
• CH
1 Press CH +/ – to select the channel
TUNER PRESET
CH5
number.
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
2 Press ?/ /to set MANUAL SET to
ERASE.
MANUAL SET
AFT
ADD• ERASE
• ON OFF
FINE TUNING
3
Repeat step 2 to preset or disable channels as required, then press
OK.
PLAY
OK
22 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
If t h e p ict u re is n o t cle a r
Normally, the Auto Fine Tuning (AFT)
function automatically tunes in channels
clearly. If, however, the picture of a
channel is not clear, you can also use the
manual tuning function.
1
4
7
2
5
8
0
3
6
9
Number
buttons,
ENTER
MENU
OK
>/./?//
• MENU
1
2
Press MENU and select TUNER PRESET,
then press OK.
TUNER PRESET
CH1
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
PLAY
OK
Selected channel
1
4
7
2
5
8
0
3
6
9
Press the number buttons to select the
channel you want to fine-tune, then press
ENTER.
TUNER PRESET
CH5
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
• ADD ERASE
• ON OFF
FINE TUNING
continued
Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Pre se t t in g ch a n n e ls (co n t in u e d )
3
4
Press >/ .to select FINE TUNING.
TUNER PRESET
CH5
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
PLAY
OK
The fine tuning meter appears.
• ADD ERASE
• ON OFF
FINE TUNING
Press ?/ /to adjust to a clearer picture,
then press OK.
TUNER PRESET
CH5
ANTENNA / CABLE ANT • CABLE
AUTO PRESET
MANUAL SET
AFT
PLAY
OK
• ADD ERASE
ON • OFF
Note that the AFT setting switches to OFF.
FINE TUNING
Tip
•
To select the channel in step 2 above, you can also use the CH +/ – buttons. In this
case, you don’t need to press ENTER.
24 Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Pla yin g a t a p e
6 EJECT
TRINITRON TV
SYNCHRO
PLAY
COUNTER
RESET
1
4
7
2
5
8
0
3
6
9
DISPLAY
P PAUSE
REPLAY
· PLAY
)
#FF
p STOP
0 3 REW
1
2
Turn on your TV and set it to the video channel.
Insert a tape.
The VCR turns on and starts playing
automatically if you insert a tape with its
safety tab removed.
continued
Basic Operations
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Pla yin g a t a p e (co n t in u e d )
3
Press · PLAY.
PLAY
OK
When the tape reaches the end, it will rewind automatically.
Additional tasks
To
Press
Stop play
Pause play
p STOP
P PAUSE
Resume play after pause P PAUSE or · PLAY
Fast-forward the tape
Rewind the tape
Eject the tape
) # FF during stop
0 3 REW during stop
6 EJECT
To play a recently w atched scene
You can immediately rewind and playback the scene you want to watch
again.
During playback, press REPLAY up to four times. The VCR rewinds the
tape about 10 seconds on the counter for each press of the button, and
restarts playback.
To use the time counter
At the point on the tape that you want to find later, press COUNTER RESET.
The counter in the display window resets to “0:00:00.” Search for the point
afterwards by referring to the counter.
VIDEO
EP
To display the counter on the TV screen, press DISPLAY repeatedly until the
time counter appears. To turn off the display, press DISPLAY twice.
Notes
•
Tapes recorded in the LP mode on other VCRs can be played back on this VCR but
the picture quality cannot be guaranteed.
•
While setting the menu on the TV screen, you cannot use the · PLAY, P PAUSE,
) # FF, 0 3 REW, or p STOP buttons.
•
•
The counter resets to “0:00:00” whenever a tape is reinserted.
The counter stops counting when it comes to a portion with no recording.
26 Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu rn in g o n t h e VCR a n d TV, a n d st a rt in g p la yb a ck
a u t o m a t ica lly (Trin it ro n TV Syn ch ro Pla y)
You can only use this function if your TV is made by Sony (Trinitron TV).
How to connect to use this function
Connect the VCR and TV with the audio/ video cable (see “Audio/ video
(A/ V) hookup” on page 7). Be sure to connect the audio/ video cable to the
VIDEO IN 1 jacks on the TV if the TV has two inputs or more. The TV must
be placed where it will respond to the remote commander while you are
pointing it at the VCR.
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in
place for about two seconds.
The VCR and TV turn on, and the TV is set to the video channel. If there is a
tape in the VCR, playback starts automatically.
Notes
•
If the Trinitron TV Synchro Play function does not work properly:
– Wait a few moments, and press the button again.
– Replace both of the batteries with new ones, and press the button again.
Note that this function may not operate some Sony TVs because of the remote
commander’s signal limitations.
•
Do not press TRINITRON TV SYNCHRO PLAY during playback. If you do so, the
TV’s input source will momentarily switch to the TV’s tuner.
Basic Operations
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV
p ro g ra m s
TV/VIDEO
1
4
7
2
5
8
0
3
6
9
r REC
CH +/–
INPUT SELECT
SP/EP
p STOP
1
2
Turn on your TV and set it to the video channel.
To record from a cable box, turn it on.
Insert a tape with its safety tab in place.
28 Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
SELECT
3
Press INPUT SELECT until a channel number appears in the display
window.
VIDEO
EP
• CH
4
5
Press CH +/ – to select the channel you want to record.
VIDEO
EP
Press SP/ EP to select the tape speed, SP or EP.
SP / EP
EP (Extra Play) provides recording time three times as long as SP
(Standard Play), however, SP produces better picture and audio
quality.
VIDEO
SP
REC
6
Press r REC to start recording.
The recording indicator lights up red in the display window.
VIDEO
Recording indicator
SP
To stop recording
Press p STOP.
continued
Basic Operations
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV p ro g ra m s (co n t in u e d )
To w atch another TV program w hile recording
1
2
3
Press TV/ VIDEO to turn off the VIDEO indicator in the display
window.
If the TV is connected to the VCR’s LINE OUT jacks, set the TV to TV
input; if not, skip this step.
Select another channel on the TV.
To save a recording
To prevent accidental erasure, break off the
safety tab as illustrated. To record on a tape
again, cover the tab hole with adhesive tape.
Safety tab
Tips
•
•
•
•
To select a channel, you can use the number buttons on the remote commander.
Enter the channel number, then press ENTER.
You can select a video source from the LINE-1 IN jacks using the INPUT SELECT
button.
The display appears on the TV screen indicating information about the tape, but the
information won’t be recorded on the tape.
If you don’t want to watch TV while recording, you can turn off the TV. When
using a cable box, make sure to leave it on.
Note
The display does not appear during still (pause) mode, search mode or slow-motion
playback.
•
30 Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV
p ro g ra m s u sin g
t h e t im e r
POWER
You can preset up to eight programs at a
time.
1
4
7
2
5
8
0
3
6
9
Before you start…
• Check that the VCR clock is set to the
correct time.
• Turn on your TV and set it to the
video channel. When using a cable
box, turn it on.
• Insert a tape with its safety tab in
place. Make sure the tape is longer
than the total recording time.
INPUT
SELECT
MENU
OK
>/./?//
p STOP
• MENU
1
Press MENU and select TIMER SET/
CHECK, then press OK.
TIMER SET / CHECK 11 / 16 MO
DATE
– / ––
– / ––
– / ––
– / ––
– / ––
– / ––
– / ––
– / ––
START STOP CH
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
––
––
––
––
––
––
––
––
PLAY
OK
continued
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Re co rd in g TV p ro g ra m s u sin g t h e t im e r (co n t in u e d )
2
Set the date, start and stop times, channel
number and tape speed:
TIMER SET / CHECK 11 / 16 MO
DATE START STOP CH
11 / 16 MO – : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
––EP
––
––
––
––
––
––
––
– / ––
– / ––
– / ––
– / ––
– / ––
– / ––
– / ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
1 Press / to flash each item in turn.
2 Press >/ . to set each item.
To correct a setting, press ? to return to
that setting and reset.
PLAY
OK
To record the same program every day or the same day every week,
press . while the date is flashing. For details, see “Daily/ weekly
recording” on page 33.
INPUT
SELECT
To record from a source connected to the LINE-1 IN jacks, press
INPUT SELECT to display “L” in the “CH” position.
3
Press / to confirm the setting.
PLAY
OK
The cursor (z) appears at the beginning of the line. To enter another
setting, move the cursor to the next line and repeat step 2.
4
5
Press OK.
PLAY
OK
• POWER
Press POWER to turn off the VCR.
The
indicator appears in the display window and the VCR
stands by for recording. When using a cable box, leave it on.
To stop recording
To stop the VCR while recording, press p STOP.
32 Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily/w eekly recording
In step 2 above, press . to select the recording pattern. Each time you press
., the indication changes as shown below. Press > to change the indication
in reverse order.
the current date n SU-SA n MO-SA n MO-FR n EVERY SA n .....
n EVERY MO n EVERY SU n 1 month later n (dates count dow n)
n the current date
To use the VCR after setting the timer
To use the VCR before a timer recording begins, just press POWER. The
indicator turns off and the VCR switches on. Remember to press POWER to
reset the VCR in timer recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
• Reset the counter.
• Display tape information on the TV screen.
• Check the timer settings.
• Watch another TV program.
To lock the VCR after setting the timer (Child Lock)
While the VCR turns on, hold POWER down on the VCR until “LOC” and
the H indicator appear in the display window. The VCR turns off and the
H indicator remains lit. The VCR will not work except for timer recording.
To unlock the VCR, hold POWER down on the VCR until the H indicator
disappears from the display window. The VCR is unlocked and turns on.
To stop timer recording while the VCR is locked, press p STOP. The
recording stops and the VCR is unlocked.
Tips
•
•
To set the channel, you can also use the CH+/ – or number buttons.
To set the tape speed, you can also use the SP/ EP button.
Basic Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Additional Operations
Pla yin g /se a rch in g
a t va rio u s sp e e d s
· PLAY
& SLOW
×2
) # FF
0 3 REW
) # FF
0 3 REW
Playback options
Operation
View the picture during fast- During fast-forward, hold ) # FF down. During
forward or rewind
rewind, hold 0 3 REW down.
Play at high speed
•
•
During playback, press ) # FF or 0 3 REW.
During playback, hold ) # FF or 0 3 REW
down. When you release the button, normal
playback resumes.
Play at twice the normal
speed
During playback, press ×2.
Play in slow motion
Play frame by frame
During playback or pause, press & SLOW.
During pause, press ) # FF or 0 3 REW. Hold
the button down to play one frame each second.
During stop, press · PLAY on the VCR while holding
Rewind and start play
0 3 REW down on the VCR.
To resume normal playback
Press · PLAY.
Tip
• Adjust the picture using the TRACKING +/ – buttons on the VCR if:
– Streaks appear while playing in slow motion.
– The picture shakes while pausing.
To set tracking to the center position, press both buttons (+/ –) at the same time.
• When you hold ) # FF or 0 3 REW down during stop, skip-search starts. For
details, see page 37.
Notes
• The sound is muted during these operations.
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but
the picture quality cannot be guaranteed.
• The picture may have snow when playing at high speed in reverse.
34 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Se a rch in g fo r a
se le ct e d p o in t o n
t h e t a p e
DISPLAY
You can easily find a selected point by
moving the pointer on the TV screen.
The VCR fast-forwards or rewinds to the
point you indicate and starts playback
automatically.
1
4
7
2
5
8
0
3
6
9
?//
) # FF
0 3 REW
· PLAY
1
2
Press DISPLAY repeatedly until the bar
indication appears on the TV screen.
A cursor (p) indicating the current position
of the tape appears on the bar indication. If
the cursor does not appear, play the tape a
few moments (by pressing · PLAY, ) #
FF or 0 3 REW) until the cursor appears.
0
120
Press ?/ /to move the pointer (+) to the
point where you want to start playback.
The VCR starts searching and the cursor (p)
moves toward the pointer. When the VCR
locates the marked point, playback starts.
0
120
continued
35
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Se a rch in g fo r a se le ct e d p o in t o n t h e t a p e (co n t in u e d )
To cancel searching
Press · PLAY or p STOP.
To turn off the bar indication
Press DISPLAY again.
Notes
•
The figure on the bar indication represents the total time length of the inserted tape
as shown below.
The total time length may not be displayed correctly for:
– tapes other than T-60, T-120, or T-160
– tapes recorded in more than one tape speed mode.
Total time length
Tape type
SP
LP
EP
60
120
240
320
180
360
480
T-60 or shorter
from T-80 to T-140
T-160 or longer
120
160
•
•
If you move the pointer (+) on the bar indication during search, the VCR searches
for the new reset point.
While the cursor (p) is displayed on the bar indication, the ) # FF/ / and 0
3 REW/ ? buttons on the remote commander work only for moving the pointer
(+), while the ) # FF and 0 3 REW buttons on the VCR work for normal tape
operation. Note, however, if you press these buttons on the VCR, searching is
canceled.
36 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Skip -se a rch in g
a u t o m a t ica lly
You can spot check a whole tape quickly.
At intervals, the VCR skips playback
while searching forward or backward.
) # FF
0 3 REW
Hold ) # FF (or 0 3 REW) down more
than two seconds during stop. “SKIP” appears on
the TV screen.
SKIP
The VCR searches forward (or backward) for
about two minutes on the counter, then fast-
forwards (or rewinds) for about ten minutes on
the counter. The VCR repeats this operation until
it stops at the end (or beginning) of the tape.
search forw ard
search forw ard
) fast-forw ard
#
) fast-forw ard
#
To cancel skip-search
Press · PLAY or p STOP.
Note
•
The VCR automatically fast-forwards (or rewinds) any portion with no recording.
37
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Re co rd in g TV
p ro g ra m s u sin g
t h e q u ick t im e r
After starting recording in the normal
way, you can have the VCR stop
recording automatically after a specified
duration.
1
4
7
2
5
8
0
3
6
9
QUICK TIMER
1
2
While recording, press QUICK TIMER once.
The indicator appears in the
display window.
VIDEO
EP
Press QUICK TIMER repeatedly to set the duration.
Each press advances the time in increments of 30 minutes.
0:00
0:30
1:00
10:30
11:00
The duration decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press QUICK TIMER repeatedly to set to the new duration.
To stop the VCR w hile recording
Press p STOP.
Usin g t h e q u ick t im e r d u rin g st o p m o d e
You can set the quick timer and start recording during stop mode by
pressing QUICK TIMER. To set the channel, you can use the CH +/ – or
INPUT SELECT buttons. Press QUICK TIMER repeatedly to set the
recording duration. The recording will start automatically.
38 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch e ckin g /
ch a n g in g /
ca n ce lin g t im e r
se t t in g s
POWER
CLEAR
1
4
7
2
5
8
0
3
6
9
Before you start…
• Turn on your TV and set it to the
video channel.
MENU
OK
>/./?//
1
2
Press POWER to turn on the VCR.
Press MENU and select TIMER SET/ CHECK:
TIMER SET / CHECK 11 / 16 MO
DATE
START STOP CH
11 / 17 TU 7 : 00
AM
8 : 00
AM
6
SP
• If you want to change a setting, go on to the
next step.
11 / 25 WE 10 : 30PM 11 : 15PM 50EP
MO – SA 1 : 00
PM
3 : 00
PM
L
EP
EVERYSU 11 : 55AM 1 : 30PM 42SP
– / ––
– / ––
– / ––
– / ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
– : ––
––
––
––
––
• If you do not need to change the settings,
press OK, then turn off the VCR to return to
recording standby.
3
4
Press >/ .to select the setting you want to change or cancel:
• To change the setting, press ?/ /to flash the item you want to
change, and press >/ .to reset it. Then, press /repeatedly until
the cursor (z) appears at the beginning of the line.
• To cancel the setting, press CLEAR.
Press OK.
If any settings remain, turn off the VCR to return to recording standby.
continued
39
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch e ckin g /ch a n g in g /ca n ce lin g t im e r se t t in g s (co n t in u e d )
When the timer settings overlap
The program that starts first has priority and the second program starts
recording only after the first program has finished. If the programs start at
the same time, the program listed first in the menu has priority.
Program 1
Program 2
Will be cut off
40 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad ju st in g t h e p ict u re
Ad ju st in g t h e t ra ckin g
Although the VCR automatically adjusts the tracking when playing a tape
(the
indicator flashes in the display window, then goes off), distortion
may occur if the tape was recorded in poor condition. In this case, manually
adjust the tracking.
Press the TRACKING +/ – buttons on the VCR to
display the tracking meter. The distortion should
disappear as you press one of the two buttons (the
indicator lights up). To resume automatic
NORMAL TRACKING
tracking adjustment, eject the tape and reinsert it.
Tracking meter
Ab o u t Ad a p t ive Pict u re Co n t ro l (APC)
Adaptive Picture Control (APC) automatically improves recording and
playback quality by adjusting the VCR to the condition of the video heads
and tape. To maintain better picture quality, we recommend that you set
APC to ON in the ADVANCED OPTIONS menu (with the APC indicator in
the display window lit).
APC playback
The APC function automatically works on all types of tapes, including rental
tapes and tapes that were not recorded with APC.
APC recording
Whenever you insert a tape and start recording at the first time, the VCR
adjusts to the tape using the APC function (the APC indicator flashes
rapidly). This adjustment is retained until the tape is ejected.
Notes
•
The auto tracking adjustment cannot be guaranteed to work with tapes recorded in
LP mode on other VCRs.
•
With the Auto Tape Speed function on, the APC function does not work if the tape
speed is automatically changed from the SP to EP mode during a timer recording,
unless the tape has been recorded in the EP mode with the APC function. For
details, see page 42.
•
There is a delay of a few seconds before the VCR actually starts recording while the
VCR analyzes the tape. To avoid the delay, first set the VCR to recording pause (the
APC indicator flashes slowly) and press r REC to have the VCR analyze the tape.
After the APC indicator stops flashing, press P PAUSE to start recording
immediately. If you press P PAUSE before the APC indicator stops flashing, the
APC function is canceled.
41
Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a n g in g m e n u o p t io n s
1
Press MENU and select ADVANCED
OPTIONS.
ADVANCED OPTIONS
APC
TAPE SELECT
• ON
• AUTO 180
OFF
AUTO TAPE SPEED • ON OFF
SHARPNESS L– –– H
2
3
Press >/ .to select the option to change, then press ?/ /to change
the setting.
Press OK to return to the original screen.
Menu choices
Initial settings are indicated in bold print.
Menu option
Set this option to
APC
ON to switch on the APC (Adaptive Picture Control)
function and improve picture quality, OFF to switch off APC.
TAPE SELECT
AUTO or 180 (when using a T-140 or T-180 tape) to operate
AUTO TAPE SPEED correctly.
AUTO TAPE SPEED
ON to change the timer recording tape speed automatically
to the EP mode when the remaining tape becomes shorter
than the recording time, OFF to keep the set tape speed.
SHARPNESS
L (Low) through H (High) to adjust the sharpness of the
picture. L to turn off the sharpness control.
42 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g w it h a n o t h e r VCR
Ho w t o h o o k u p t o re co rd o n t h is VCR
This VCR (Recorder)
TV
LINE-1 IN
Other VCR (Player)
LINE OUT
VMC-710M/720M audio/video cable
(not supplied)
: Signal flow
Notes
•
•
Make sure you connect the plugs to jacks of the same color.
If you connected this VCR to both the LINE IN and LINE OUT jacks of the other
VCR, select the input correctly to prevent a humming noise.
continued
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g w it h a n o t h e r VCR (co n t in u e d )
Op e ra t io n (w h e n re co rd in g o n t h is VCR)
Before you start editing
• Turn on your TV and set it to the
video channel.
• Press INPUT SELECT on the remote
commander to display “L” in the
display window.
• Press SP/ EP on the remote
commander to select the tape speed,
SP or EP.
P PAUSE
r REC
1
Insert a source tape with its safety tab removed into the other
(playback) VCR. Search for the point to start playback and set it to
playback pause.
2
Insert a tape with its safety tab in place into this (recording) VCR.
Search for the point to start recording and press P PAUSE.
3
4
Press r REC on this VCR and set it to recording pause.
To start editing, press the P PAUSE buttons on both VCRs at the same
time.
To stop editing
Press the p STOP buttons on both VCRs.
Note
•
If you start recording following the procedure above, the VCR won’t start recording
with the APC function. To record a tape with the APC function, press r REC again
during recording pause in step 3 so that the VCR analyzes the tape. Then when you
start recording in step 4, press P PAUSE immediately after the APC indicator stops
flashing. If you press P PAUSE before the APC indicator stops flashing, the APC
function is canceled.
44 Additional Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Ge n e ra l se t u p in fo rm a t io n
TV
Se t t in g t h e RF u n it
When connecting the VCR to the TV
using only the antenna cable, you must
set the RF UNIT switch on the rear of the
VCR so that the TV can receive the
correct signal from the VCR.
RF UNIT
CH3 CH4
POWER
CHANNEL +/–
1
Set the RF UNIT switch on the rear of the VCR to CH3 or CH4,
whichever channel is not used in your area. If both are used, set the
switch to either channel.
2
3
Press POWER to turn on the VCR.
Press TV/ VIDEO on the remote commander to turn on the VIDEO
indicator in the VCR’s display window.
4
5
Press CHANNEL +/ – to display a channel number in the display
window. Select an active channel number in your area.
Turn on your TV and set it to the channel you selected in step 1
(channel 3 or 4).
The selected TV channel broadcast appears on the TV screen. If the
channels change when you press CHANNEL +/ –, you have made the
correct setting.
Whenever you use the VCR, set the TV to the channel selected in step 1.
continued
45
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Ge n e ra l se t u p in fo rm a t io n (co n t in u e d )
At t a ch in g t h e e xt e rn a l
a n t e n n a co n n e ct o r
300-ohm tw in
lead cable
When using a 300-ohm twin lead cable
for a VHF/ UHF antenna, use the EAC-
32 antenna connector (not supplied) to
connect the antenna to the VCR.
EAC-32 Antenna
connector (not
supplied)
1
2
3
Loosen the screws on the antenna connector.
Wind the twin leads around the screws on the antenna connector.
Retighten the screws.
300-ohm tw in
lead cable
At t a ch in g a UHF/VHF b a n d
m ixe r
When using both a 75-ohm coaxial cable
and a 300-ohm twin lead cable for a
VHF/ UHF antenna, use the EAC-66
UHF/ VHF band separator/ mixer (not
supplied) to connect the antenna to the
VCR.
EAC-66
UHF/VHF
band
separator/
mixer (not
supplied)
75-ohm coaxial
cable
1
2
3
4
Loosen the screws on the mixer.
Wind the twin leads around the screws on the mixer.
Retighten the screws.
Connect the 75-ohm coaxial cable to the mixer.
46 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g
If you have any questions or problems not covered below, please consult your
nearest Sony dealer.
Symptom
Remedy
The POWER switch does not
function.
•
•
Connect the AC power cord securely.
Make sure the VCR is not locked. To unlock, hold
down POWER on the VCR until the Hindicator
disappears.
The power is turned on but the
VCR does not operate.
•
•
•
Moisture condensation occurs. Turn the power off,
unplug the AC power cord and leave the VCR to dry
for over an hour.
The clock has stopped and
“–:– –” lights in the display
window.
The clock stops if the VCR is disconnected from the
wall outlet for more than one hour. Reset the clock
(and timer).
The playback picture does not
appear on the TV screen.
Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
The picture is not clear.
•
•
Adjust the tracking with the TRACKING +/ – buttons.
The video heads are dirty (see below). Clean the video
heads using the Sony T-25CLD, T-25CLDR, or T-
25CLW video head cleaning cassette. If these cleaning
cassettes are not available in your area, have the heads
cleaned at your nearest Sony service facility (a
standard service charge will be required). Do not use a
liquid-type cleaning cassette other than Sony’s, as it
may damage the video heads.
•
•
The video heads may have to be replaced. Consult
your local Sony dealer for more information.
The picture rolls vertically
during picture search.
Adjust the vertical hold control on the TV or monitor.
The picture has no sound.
•
•
The tape is defective.
If you made A/ V connections, check the audio cable
connection.
Symptoms caused by contaminated video heads
• Normal picture
• Unclear picture
• Rough picture
• No picture (or
black & w hite
screen appears)
initial
terminal
contamination
continued
47
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Tro u b le sh o o t in g (co n t in u e d )
Symptom
Remedy
A TV program does not appear
on the TV screen.
•
Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
TV reception is poor.
•
•
Adjust the TV antenna.
The tape starts playing as soon
as it is inserted.
The safety tab has been removed. To record on this
tape, cover the tab hole.
The tape ejects when you press
•
Check that the safety tab has not been removed.
r REC.
Nothing happens when you
press r REC.
•
•
Make sure the tape is not at its end.
Select the correct source. Select a channel number with
the CH +/ – buttons when recording TV programs;
select “L” with the INPUT SELECT button when
recording from other equipment.
The timer does not operate.
•
•
•
•
•
•
Check that the clock is set.
Make sure a tape has been inserted.
Check that the safety tab has not been removed.
Make sure the tape is not at its end.
Make sure a program has been set for timer recording.
Make sure your timer settings have not already passed
the current time.
•
•
Check that the cable box is turned on.
The clock stops if the VCR is disconnected from the
wall outlet for more than one hour. Reset the clock and
timer.
A tape cannot be inserted.
•
Check that a tape isn’t already in the tape timer
compartment.
The remote commander does
not function.
•
•
•
Make sure you are pointing the remote commander at
the remote sensor on the VCR.
Replace all the batteries in the remote commander with
new ones if they are weak.
Make sure the TV / VIDEO remote control switch is
set correctly.
The tracking meter does not
appear on the screen.
•
•
The recording condition of the tape is very poor and
tracking cannot be adjusted.
The VCR needs to be cleaned.
Clean the cabinet, panel and controls with a dry, soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent,
such as alcohol or benzine.
48 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e cifica t io n s
Syst e m
Tim e r se ct io n
Format
Clock
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Quartz locked
Timer indication
12-hour cycle
Timer setting
Double azimuth four heads
Video signal
8 programs per month (max.)
Power back-up
NTSC color, EIA standards
Tape speed
Built-in self-charging capacitor
Back-up duration: up to 1 hour at a time
SP: 33.35 mm/ s (1 5/ 16 inches/ s)
EP: 11.11 mm/ s (7/ 16 inches/ s)
LP: 16.67 mm/ s (21/ 32 inches/ s),
playback only
Ge n e ra l
Power requirements
120 V AC, 60 Hz
Power consumption
23 W
Maximum recording/ playback time
9 hrs. in EP mode (with T-180 tape)
Fast-forward and rewind time
Operating temperature
5°C to 40°C (41°F to 104°F)
Storage temperature
–20°C to 60°C (–4°F to 140°F)
Dimensions
Approx. 3 min. (with T-120 tape)
Tu n e r se ct io n
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W+1 to W+84
Antenna
Approx. 355 × 96 × 285 mm
(14 × 3 7/ 8 × 11 1/ 4 inches) (w/ h/ d)
including projecting parts and controls
Mass
75-ohm antenna terminal for VHF/ UHF
Approx. 3.7 kg (8 lb 03 oz)
In p u t s a n d o u t p u t s
Su p p lie d a cce sso rie s
LINE-1 IN
Remote commander (1)
VIDEO IN, phono jack (1)
Size AA (R6) batteries (2)
Input signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
75-ohm coaxial cable with F-type connectors (1)
AUDIO IN, phono jack (1)
Input level: 327 mVrms
Design and specifications are subject to change
without notice.
Input impedance: more than 47 kilohms
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced,
sync negative
AUDIO OUT, phono jack (1)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
49
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls
Refer to the pages indicated in parentheses ( ) for details.
Fro n t p a n e l
1 POWER switch/ indicator (32)
2 Tape compartment
7 p STOP button (26)
8 P PAUSE button (26)
3 0 3 REW (rewind) button (26, 34)
4 · PLAY button (26)
9 CHANNEL/ TRACKING +/ –
buttons (34, 41)
!º REPLAY button (26)
!¡ Remote sensor (5)
!™ 6 EJECT button (26)
5 ) # FF (fast-forward) button (26,
34)
6 r REC (record) button (29)
50 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Disp la y w in d o w
VIDEO APC
LPSP
EP
1 Timer indicator (32)
5 Child Lock indicator (33)
2 Tape speed indicator (29)
6 Tracking indicator (41)
3 VIDEO indicator (30, 45)
7 Time counter/ clock/ line/ channel
indicator (26, 29, 44)
4 APC (Adaptive Picture Control)
indicator (41)
8 Tape/ recording indicator (29)
continued
51
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls (co n t in u e d )
Re a r p a n e l
1 AC power cord (6)
4 RF (Radio Frequency) UNIT switch
(45)
2 LINE-1 IN AUDIO/ VIDEO jacks
(43)
5 LINE OUT AUDIO/ VIDEO jacks (7)
3 VHF/ UHF IN/ OUT connectors (8,
10, 12, 14)
52 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Re m o t e co m m a n d e r
1 TV / VIDEO remote control switch
(5)
2 6 EJECT button (26)
3 TV/ VIDEO button (30, 45)
4 TRINITRON TV SYNCHRO PLAY
button (27)
1
4
7
2
5
8
0
3
6
9
5 DISPLAY button (26, 35)
6 COUNTER RESET button (26)
7 QUICK TIMER button (38)
8 r REC (record) button (29)
9 SP (Standard Play)/ EP (Extra Play)
button (29)
0 INPUT SELECT button (29, 32)
!¡ & SLOW button (34)
!™ ×2 button (34)
!£ Tape/ menu operation buttons
MENU button (16, 42)
P PAUSE/ > button (26)
p STOP/ . button (26)
0 REW (rewind) 3/ ? button
(26, 34)
) FF (fast-forward) #/ / button
(26, 34)
· PLAY/ OK button (26)
continued
53
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x t o p a rt s a n d co n t ro ls (co n t in u e d )
!¢ POWER switch (32)
!∞ CLEAR button (39)
!§ Channel number buttons and
ENTER button (30)
!¶ CH (channel) +/ – buttons (29)
!• VOL (volume) +/ – buttons
!ª REPLAY button (26)
1
4
7
2
5
8
0
3
6
9
54 Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
In d e x
A, B
E, F, G, H, I, J, K
Editing 43
S
AFT (Auto Fine Tuning) 23
Safety tab 30
Antenna hookup
8
EP mode 29
Searching
APC (Adaptive Picture
Control) 41
at various speeds 34
for a selected point 35
skip-search 37
L, M, N, O
Audio/ video (A/ V)
Language selecting 18
Locking the VCR 33
LP mode 26
hookup
7
SP mode 29
C
T, U, V, W, X, Y, Z
Timer recording 31
Cable hookup 10, 12, 14
Canceling timer settings 39
Changing timer settings 39
Checking timer settings 39
Child Lock 33
P
canceling timer
settings 39
Picture adjustment 23, 34,
41
changing timer
settings 39
Playback 25
at various speeds 34
frame-by-frame 34
slow motion 34
Cleaning the video
heads 47
checking timer
settings 39
Clock setting 16
Connecting
daily/ weekly
recording 33
Presetting channels 19
overlapping timer
recordings 40
cable TV 10, 12, 14
Q
external antenna
connector 46
Quick timer 38
Tracking adjustment 34, 41
Trinitron TV Synchro Play
27
UHF/ VHF band
mixer 46
R
Recording 28
Counter 26
saving 30
while watching another
program 30
D
Disabling channels 21
Dubbing. See Editing.
55
Additional Information
Download from Www.Somanuals.com. All Manuals Search And Download.
u ick re fe re n ce t o u sin g t h e VCR
Q
Ho o ku p 1
Ho o ku p 2
Ho o ku p 3
To p la y a t a p e
To p la y a t a p e
To p la y a t a p e
1 Set the TV to channel 3 or
4 (or to video input, if you
made A/ V connections.)
1 Set the TV to channel 3 or
4 (or to video input, if you
made A/ V connections.)
1 If you made A/ V
connections, set the TV to
video input.
If you didn’t use A/ V
hookup:
Turn on the cable box.
Set the cable box to
channel 3 or 4.
Set the TV to the output
channel of the cable box
(usually 2, 3 or 4).
2 Insert a tape and press
PLAY. If there’s no picture
on your TV, press the
VCR’s TV/ VIDEO button
until the VIDEO indicator
comes on in the display
window.
2 Insert a tape and press
PLAY. If there’s no picture
on your TV, press the
VCR’s TV/ VIDEO button
until the VIDEO indicator
comes on in the display
window.
•
•
•
To re co rd a p ro g ra m
To re co rd a p ro g ra m
2 Insert a tape and press
PLAY.
1 Press MENU and select
TIMER SET/ CHECK.
2 Set the date, time, channel,
and tape speed.
3 Press OK.
4 Insert a tape.
5 Press POWER to turn off
the VCR.
1 Turn on the cable box.
2 Set the cable box to the
channel you want to
record.
3 Press MENU and select
TIMER SET/ CHECK.
4 Set the date, time, channel,
and tape speed.
5 Press OK.
6 Insert a tape.
To re co rd a p ro g ra m
1 Press MENU and select
TIMER SET/ CHECK.
2 Set the date, time, channel,
and tape speed.
3 Press OK.
4 Insert a tape.
5 Press POWER to turn off
the VCR.
To w a t ch TV
1 Turn off the VCR, or press
the VCR’s TV/ VIDEO
button until the VIDEO
indicator in the display
window goes off.
7 Press POWER to turn off
the VCR.
Leave the cable box on.
To w a t ch TV
1 Turn off your VCR, or
press the VCR’s TV/
VIDEO button until the
VIDEO indicator in the
display window goes off.
2 Select the channel with
your cable box (if you have
one) or with your TV.
To w a t ch TV
2 Set the TV to the channel
you want to watch.
1 Turn off your VCR, or
press the VCR’s TV/
VIDEO button until the
VIDEO indicator in the
display window goes off.
2 Turn on your cable box.
3 Set the TV to the cable box
output channel (usually 2,
3, or 4).
4 Set the cable box to the
channel you want to
watch.
If you have any questions about this product, you may call: Sony Customer Information Center
1-800-222-SONY (7669) or write to: Sony Customer Information Center Sony Drive, Mail Drop
#T1-11, Park Ridge, NJ 07656
Sony Corporation Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|