3-619-326-11(1)
Digital
Videocassette
Recorder
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
Note
The supplied CD-ROM includes operation manuals
for the DSR-1500A/1500AP Digital Video Cassette Recorder
(English, Japanese, French, German, Italian and Spanish versions).
DSR-1500A/1500AP
© 2002 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Record
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
The model and serial numbers are located at the bottom.
Record these numbers in the spaces provided below. Refer
to them whenever you call upon your Sony dealer
regarding this product.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the
appliance.
Model No.
Serial No.
WARNING
* The graphical symbols are on the bottom enclosure.
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
WARNING: THIS WARNING IS APPLICABLE FOR
USA ONLY.
Using this unit at a voltage other than 120 V may require
the use of a different line cord or attachment plug, or both.
To reduce the risk of fire or electric shock, refer servicing
to qualified service personnel.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
THIS APPARATUS MUST BE EARTHED.
For customers in the USA (DSR-1500A only)
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquid, such as vases,
shall be placed on the apparatus.
The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
IMPORTANT
The nameplate is located on the bottom.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with
the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Cuing Up to Any Desired Position Set as Point A
or B ...................................................................... 47
Displaying Time Data and Operation Mode
Indications ...........................................................49
High-Speed and Low-Speed Search—Quickly and
Table of Contents
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Returning Menu Settings to Their Factory Default
Connections for a Digital Non-Linear Editing System
Table of Contents
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview Chapter
1
High picture quality and high stability
Video signals are separated into color difference signals
and luminance signals, which are encoded and compressed
to one-fifth size before being recorded to ensure stable and
superb picture quality.
Features
1
The DSR-1500A/1500AP is a / -inch digital
4
Because the recording is digital, multi-generation dubbing
can be performed with virtually no deterioration of quality.
videocassette recorder using the DVCAM™ digital
recording format.
The unit is equipped with an i.LINK/DV* interface as
standard, so that it can be used as a low-cost, compact
feeder, player or viewer in a non-linear editing system**
without requiring any optional boards. When using the unit
as an editor, the optional boards available for the unit allow
you to select required input signal formats.
Wide track
The recording track width is 15 µm, 50% wider than the 10
µm of the DV format. This ensures adequate reliability for
professional use.
The unit is playback-compatible with tapes recorded in DV
format (excluding tapes recorded in LP mode) as well as
DVCPRO (25 Mbps) format. Playing back such tapes on
the unit does not require any adapter.
These and other features of the unit make it suitable for use
under diversified conditions. It can be used, for example,
for desk-top editing or for such applications as electronic
news gathering (ENG) and non-linear editing aboard
outside broadcast vans, at production houses or at
broadcasting stations.
High-quality PCM digital audio
PCM recording makes for a wide dynamic range and a
high signal-to-noise ratio, thereby enhancing sound
quality.
There are two recording modes: 2-channel mode (48-kHz
sampling and 16-bit quantization), which offers sound
quality equivalent to the DAT (Digital Audio Tape)
format, or 4-channel mode (32-kHz sampling and 12-bit
quantization).
* i.LINK and are trademarks and indicate that this product is in agreement
with IEEE1394-1995 specifications and their revisions.
Superior playback compatibility with DV
and DVCPRO (25 Mbps) formats
** Non-linear editing: This is an editing method that uses video and audio
signals digitally encoded and recorded on a hard disk as digital data. When
compared with conventional (linear) editing methods, non-linear editing
offers vastly improved efficiency in editing operations, for example, by
eliminating tape transport time.
Tapes recorded in DV format (excluding the tapes
recorded in LP mode) as well as DVCPRO (25 Mbps)
format can be played back on this unit without requiring a
cassette adapter. You can use the recordings on such tapes
as source material for editing, applying such functions as
the jog audio and digital slow-motion playback as
required. Using the material, editing can be carried out to
single-frame precision.
The following are the principal features of the unit.
DVCAM Format
1
DVCAM is a professional / -inch digital recordingformat
4
The unit can also be used for recording in DV format (in
SP mode only).
developed by Sony from the consumer DV component
digital format.
Features
7
Download from Www.Somanuals.com. All Manuals Search And Download.
selected with front panel buttons for input and menu
items for output.
• Analog audio: The unit has two audio channels. When
in 4-channel mode, you can input two channels of audio
either as channels 1 and 2 or as channels 3 and 4. The two
audio channels can be output also either as channels 1
and 2 or as channels 3 and 4.
The analog output interfaces are provided as standard so
that the unit can readily be used as a viewer, for example,
at broadcasting stations and aboard outside broadcast vans
without requiring any optional boards.
Inputting analog video and audio signals requires the
optional DSBK-1504/1504P Analog Input Board.
Note
When playing back a tape recorded in DVCPRO (25
Mbps) format, the outputs in SDTI format of this unit are
muted. Furthermore, it is not possible to playback the cue-
audio track of the tape.
Support for three cassette sizes
There are two sizes of DVCAM cassette: standard and
mini. You can use either size with this unit.
The unit also accepts L and M sizes of DVCPRO cassette.
• When a cassette is inserted, the reel mechanism of the
unit automatically adjusts to the size of the inserted
cassette.
• The capacity of a standard cassette is 184 minutes of
recording/playback, and that of a mini cassette is 40
minutes. When DV (SP) format is used, these recording/
playback times are extended to 276 minutes and 60
minutes, respectively.
Compact Size
The compact size of the unit makes the unit suitable for use
as a desk-top editor or feeder machine for non-linear
editing or as a viewer compatible with a full range of
digital and analog signal formats aboard an outside
broadcast van.
Variety of Interfaces
Facilities for High-Efficiency Editing
Digital interfaces
The following optional digital interfaces can be used with
the unit.
• i.LINK (DV): The unit’s i.LINK/DV IN/OUT
connector can input and output digital video and audio
signals in DV format.
• SDTI (QSDI)* (optional DSBK-1501 Digital Input/
Output Board): When the unit is fitted with the optional
DSBK-1501 board, SDTI (QSDI)-format video, audio
and time code signals can be transferred between the unit
and the Sony EditStation at normal speed. When this unit
is connected to another DVCAM VCR, it is possible to
copy compressed signals between the two VCRs.
(You cannot use the SDTI (QSDI) and SDI (see next
paragraph) interfaces at the same time. You can select
either of the two using front panel buttons for input or
with a menu item for output.)
Digital slow motion playback
Using the frame memory function, noiseless slow motion
playback is possible at any speed in the range 0.5 times*
normal speed.
* The positive direction refers to forward movement of the tape, and the
negative direction to reverse movement.
Digital jog sound function
When searching at speeds in the range 0.5 times normal
speed, the digital jog sound function is enabled. The audio
signal is saved in temporary memory, and replayed
according to the search speed. This allows searching on the
sound track.
• SDI (serial digital interface)/AES/EBU (optional
DSBK-1501 Digital Input/Output Board): When the
unit is fitted with the optional DSBK-1501 board, it can
input and output D1 (component) format digital video
and audio signals and also AES/EBU-format digital
audio signals.
Remote control
The unit can be operated by remote control from an editing
control unit that supports the RS-422A interface or an
optional SIRCS*-compatible remote control unit such as
the DSRM-10.
* SDTI is the name of a standard interface established as SMPTE 305M.
QSDI is a type of SDTI. This unit uses SDTI to transmit DV data, and the
input/output connectors are labeled “SDTI (QSDI).”
* SIRCS (Sony Integrated Remote Control System): A command protocol
to remote control Sony professional videocassette recorders/players.
High-speed search function
Analog interfaces
The unit has a picture search function that allows you to
view color picture at playback speeds up to 85 times
normal speed in forward and reverse directions.
When remote-controlling this unit in shuttle mode from an
editing control unit or a remote control unit, you can search
The unit can also use the following analog interfaces.
• Analog video: These interfaces include a component
interface, composite interface, and S-video interface.
The same BNC type input and output connectors are
used to input and output signals in different formats
Features
8
Download from Www.Somanuals.com. All Manuals Search And Download.
at any speed in the range 0 (still) to 60 times normal speed
in both directions. You can also search frame-by-frame in
jog mode.
At search speeds up to 10 times normal speed in both
directions, you can also hear playback audio.
Internal test signal generator
The unit has built-in video and audio test signal generators.
The video test signal generator can produce either a color
bar signal or a black burst signal. The audio test signal
generator can generate either a silent signal or a 1-kHz sine
wave signal. Menu items are provided for selecting the test
signals to be generated.
Quick mechanical response
When you use the tape transport buttons of the unit, the
tape inserted in the unit responds quickly.
Support for ClipLink function
In response to commands sent from the EditStation, index
pictures recorded on tape or ClipLink log data recorded in
the cassette memory can be transferred to the EditStation.
The EditStation operator can then efficiently use these
pictures and data in a preliminary editing session.
Superimposition function
Time code values, operation mode indications, error
messages, and other text data can be superimposed and
output in analog composite video signals.
For an overview of the ClipLink function, see the appendix
Other Features
Video process control
Menu system for functionality and
operation settings
For analog video output and SDI-format video output, you
can use menu items to adjust the video output level,
chroma signal output level, setup level (for DSR-1500A),
black level (for DSR-1500AP), and chroma phase.
The unit provides a menu system to make its various
functions easier to use and set up its operation conditions.
Easy maintenance functions
Reference signal connection
Self-diagnostic/alarm function: This function
automatically detects setup and connection errors,
operation faults, and other problems. It also displays a
description of the problem, its cause, and the
recommended response on the video monitor screen or
time counter display.
The reference video input connector of the unit is provided
with a loop-through connector which can be used to
connect the input reference video signal to other
equipment. When there is no loop-through connection, the
reference video input connector is automatically provided
with a 75-ohm termination.
Digital hours meter: The digital hours meter functions
include four kinds of tally operations for operating
hours, head drum usage hours, tape transport hours,
and tape threading/unthreading times. The tally results
can be viewed on the video monitor or the time counter
display.
Closed caption compatibility
Whether or not to include closed captions in a recording
can be determined with menu items (for DSR-1500A
only).
AC operations
The unit operates with an AC power source in the range
100 to 240 V, 50/60 Hz.
Optional Accessories
DSBK-1501 Digital Input/Output Board
This interface enables digital video and audio signals in the
SDI or SDTI (QSDI) format (either format to be selected
with front panel buttons for input or with a menu item for
output) and also AES/EBU-format digital audio signals to
be transferred between this unit and digital Betacam VCRs
or other digital equipment.
Internal and external time codes
An internal time code generator and reader enables time
code compliant with SMPTE (for DSR-1500A)/EBU
(DSR-1500AP) format to be recorded and played back.
This allows editing to single frame precision.
Outputting or inputting time code (LTC) to or from an
external device is also possible using the TC IN/OUT
connectors.
DSBK-1504/1504P Analog Input Board
When this interface is installed, the unit can input analog
video and audio signals. The same BNC type input
connectors are used to input analog video signals in
different formats selected with front panel buttons.
The unit is also compatible with VITC.
Features
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The analog video signals that can be input are as follows.
• Composite video signals
• S-video signals
• Component video signals (Y, R−Y and B−Y)
Features
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD-ROM Manual
The supplied CD-ROM includes operation manuals for the
DSR-1500A/1500AP Digital Video Cassette Recorder
(English, Japanese, French, German, Italian and Spanish
versions).
2 Select and click the operation manual that you want to
read.
A PDF file of the operation manual opens.
Note
If you lose the CD-ROM disc or become unable to read its
content, for example because of a hardware failure, contact
a Sony service representative.
CD-ROM System Requirements
The following are required to access the supplied CDROM
disc.
• Computer: PC with MMX Pentium 166 MHz or faster
CPU, or Macintosh computer with PowerPC CPU.
- Installed memory: 32 MB or more
- CD-ROM drive: 8 or faster
• Monitor: Monitor supporting resolution of 800 × 600 or
higher
•
•
MMX and Pentium are registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.
PowerPC is a registered trademark of International Business Machines
Corporation.
Macintosh is a registered trademark of Apple Computer, Inc.
Microsoft is a registered trademark of Microsoft Corporation in the United
States and/or other countries.
•
•
•
•
Netscape Navigator is a registered trademark of Netscape
Communications Corporation in the U.S. and other countries.
Adobe and Acrobat are registered trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
When these requirements are not met, access to the CD-
ROM disc may be slow, or not possible at all.
Preparations
The following software must be installed on your
computer in order to use the operation manuals contained
in the CD-ROM disc.
• Microsoft Internet Explorer Version 4.0 or higher, or
Netscape Navigator Version 4.0 or higher
• Adobe Acrobat Reader Version 4.0 or higher
Notes
• If Microsoft Internet Explorer is not installed, it may be
downloaded from the following URL:
http://www.microsoft.com/ie
• If Netscape Navigator is not installed, it may be
downloaded from the following URL:
http://home.netscape.com/
• If Adobe Acrobat Reader is not installed, it may be
downloaded from the following URL:
http://www.adobe.com/products/acrobat/readstep.html
To Read the CD-ROM Manual
To read the operation manual contained in the CDROM
disc, do the following.
1 Insert the CD-ROM disc in your CD-ROM drive.
A cover page appears automatically in your browser.
If it does not appear automatically in the browser,
double click the index.htm file on the CD-ROM disc.
Using the CD-ROM Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
Front Panel
f Cassette compartment
g LOCAL/REMOTE switch
POWER
EJECT
a POWER switch
h EJECT button
LOCAL
b Audio level meters
1
3
REC/PB
LEVEL
REMOTE
2
4
MENU
RESET(NO)
OVER
OVER
dB
0
dB
0
INPUT
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
VIDEO
V:SDTI COMPOSITE
AUDIO
CH-1 1/2 CH-2 3/4
S VIDEO ANALOG ANALOG
REPEAT
SDTI
i.LINK
-12
-20
-12
-20
TC
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
SET(YES)
PRESET
OUTPUT
VIDEO
SDI COMPOSITE
-30
-40
-30
-40
VAR
REC
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
SDTI
S VIDEO
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
EDIT MODE
PB
PRESET
MONITOR
SELECT
METER
CH-1/2 3/4
INPUT SELECT
VIDEO
COUNTER
SELECT
SDTI/i.LINK
CH1 1/2
CH2 3/4
SYNC
SC
REW
PLAY
F FWD
STOP
REC
c PHONESconnector
PHONES
and control knob
CONTROL
S
d SC control
j METER CH-1/2 3/4
l CONTROL S connector
k COUNTER SELECT button
button
e SYNC control
i MONITOR SELECT button
POWER
EJECT
LOCAL
1
3
REC/PB
LEVEL
REMOTE
2
4
MENU
RESET(NO)
OVER
OVER
dB
0
dB
0
INPUT
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
VIDEO
V:SDTI COMPOSITE
AUDIO
CH-1 1/2 CH-2 3/4
S VIDEO ANALOG ANALOG
REPEAT
SDTI
i.LINK
A Audio input/output level
control section (see
-12
-20
-12
-20
TC
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
SET(YES)
PRESET
OUTPUT
VIDEO
SDI COMPOSITE
-30
-40
-30
-40
VAR
REC
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
SDTI
S VIDEO
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
EDIT MODE
PB
PRESET
MONITOR
SELECT
METER
CH-1/2 3/4
INPUT SELECT
VIDEO
COUNTER
SELECT
SDTI/i.LINK
CH1 1/2
CH2 3/4
SYNC
SC
REW
PLAY
F FWD
STOP
REC
B Video/audio input setting
PHONES
section (see page 15)
CONTROL
S
E Menu control section
D Tape transport control
section (see page 20)
Location and Function of Parts
12
Download from Www.Somanuals.com. All Manuals Search And Download.
a POWER switch
d
SC (subcarrier phase) control
Press the “ ” side to power on the unit. This causes the
audio level meters and the display section to light. To
power off the unit, press the “ ” side of the switch.
Turn this control to accurately adjust the subcarrier phase
of the composite video output signal of the unit with
respect to the reference video signal. Use a cross-point
(Phillips) screwdriver to turn it.
b Audio level meters
These two meters indicate the recording audio levels
during recording or EE mode* and the playback audio
levels during playback. When the audio level indicated on
a meter exceeds 0 dB, the OVER indicator for the meter
lights.
e SYNC (synchronization phase) control
Turn this control to accurately adjust the synchronization
phase of the output video signal of the unit with respect to
the reference video signal. Use a cross-point (Phillips)
screwdriver to turn it.
The short bars to the right of level indication bars indicate
that those levels are reference audio recording levels.
The settings made with the METER CH-1/2 3/4 button and
MONITOR SELECT button select the audio channels for
level indications on these meters as follows.
f Cassette compartment
Accepts DVCAM, DV and DVCPRO (25 Mbps)
videocassettes.
When CH-1/2 mode is selected with the METER CH-1/
2 3/4 button:
g LOCAL/REMOTE switch
Selects whether the unit is operated from its front panel or
from external equipment.
REMOTE: The unit is operated from external equipment
connected to the REMOTE connector or i.DV IN/
OUT connector on the rear panel.
Every time the MONITOR SELECT button is pressed,
the audio channel selection for level indications on the
two meters cycles through the following options.
• CH-1 (channel 1) only
Only the CH-1 indicator lights.
• CH-2 (channel 2) only
Only the CH-2 indicator lights.
• CH-1 and CH-2 (channels 1 and 2)
Both the CH-1 and CH-2 indicators light.
When CH-3/4 mode is selected with the METER CH-1/
2 3/4 button:
LOCAL: The unit is operated from its front panel or from
a SIRCS-compatible remote control unit connected to
the CONTROL S connector on the front panel.
h EJECT button
When you press this button, the cassette is automatically
ejected after a few seconds.
Every time the MONITOR SELECT button is pressed,
the audio channel selection for level indications on the
two meters cycles through the following options.
• CH-3 (channel 3) only
i MONITOR SELECT button
Use this button and the METER CH-1/2 3/4 button to
select the audio channels:
Only the CH-3 indicator lights.
• CH-4 (channel 4) only
Only the CH-4 indicator lights.
• CH-3 and CH-4 (channels 3 and 4)
Both the CH-3 and CH-4 indicators light.
• for level indications on the audio level meters
• for audio output via the PHONES connector on the front
panel
• for audio output via the MONITOR connector on the
rear panel
* E-E mode: Abbreviation of “Electric-to-Electric mode.” In this mode,
video and audio signals input to the VCR are output after passing through
internal electric circuits, but not through magnetic conversion circuits such
as heads and tapes. This can be used to check input signals and for
adjusting input signal levels.
Depending on the setting made with the METER CH-1/2
3/4 button, the channels for output to the above meters and
connectors are selected as follows.
When CH-1/2 mode is selected with the METER CH-1/
2 3/4 button:
c PHONES connector (stereo phone jack) and
control knob
Connect stereo headphones to the connector for audio
monitoring during recording or playback. The control
knob controls the volume of the headphones. It also
controls the level of the audio signal output from the
MONITOR connector on the rear panel.
The settings made with the METER CH-1/2 3/4 button and
MONITOR SELECT button select the audio channels for
audio output via this connector. The same channel
selection as for the audio level meters applies to this
connector.
Audio level meters
PHONES
connector
MONITOR
connector
CH-1 (channel 1) only.
Channel 1 only Channel 1 only
Only the left meter lights. (monaural)
CH-2 (channel 2) only.
Only the right meter
lights.
Channel 2 only Channel 2 only
(monaural)
CH-1 and CH-2 (channels Channels 1
Channels 1
1 and 2).
and 2 (stereo) and 2 (mixed)
Both the left and right
meters light.
Location and Function of Parts
13
Download from Www.Somanuals.com. All Manuals Search And Download.
A Audio input/output level control section
When CH-3/4 mode is selected with the METER CH-1/
2 3/4 button:
a REC/PB LEVEL control knobs
Audio level meters
PHONES
connector
MONITOR
connector
1
REC/PB
LEVEL
2
CH-3 (channel 3) only.
Channel 3 only Channel 3 only
Only the left meter lights. (monaural)
CH-4 (channel 4) only.
Only the right meter
lights.
Channel 4 only Channel 4 only
(monaural)
3
4
CH-3 and CH-4 (channels Channels 3
Channels 3
3 and 4).
Both the left and right
meters light.
and 4 (stereo) and 4 (mixed)
VAR
REC
PB
PRESET
j METER CH-1/2 3/4 button
b VAR switch
Pressing this button toggles the audio level meter mode
between CH-1/2 (channels 1 and 2) and CH-3/4 (channels
3 and 4).
a REC/PB LEVEL control knobs
These knobs used to control audio levels function
differently depending on the setting of the VAR switch as
follows.
The settings made with this button and the MONITOR
SELECT button select the channels for level indications
and audio output.
VARswitch Functions of control knobs
setting
k COUNTER SELECT button
PRESET
Control knobs are not effective.
The analog audio input/output levels are set to
the reference level set with the LEVEL
Selects the type of time data to be shown in the time
counter display. Each press of this button cycles through
the following three indicator display options:
• COUNTER (CNT: count value of the time counter)
• TC (time code)
REC
PB
Control the analog/digital audio input levels on
channels 1 to 4 during recording.
Control the analog/digital audio output levels
on channels 1 to 4 during playback.
• U-BIT (user bits)
Note
b VAR switch
Use to switch the way in which the REC/PB LEVEL
control knobs function.
If the LOCAL/REMOTE switch is set to REMOTE, the
COUNTER SELECT button does not operate while the
tape is moving. In this case, make the time data selection
via the external equipment connected to the REMOTE
connector on the rear panel.
l CONTROL S connector (stereo minijack)
Connect a SIRCS-compatible remote control unit such as
the DSRM-10 to this connector.
Location and Function of Parts
14
Download from Www.Somanuals.com. All Manuals Search And Download.
c CH1 1/2 (audio channel 1 or 1/2) button
Each press of this button cycles through the following
input audio signal selection options for audio channel 1
(when in 2-channel mode) or for audio channels 1 and 2
(when in 4-channel mode).
B Video/audio input setting section
INPUT SELECT
SDTI/i.LINK
VIDEO
CH1 1/2
CH2 3/4
• Analog audio signal input to the AUDIO IN 1/3
connector (optional DSBK-1504/1504P board required)
• Digital audio signal in AES/EBU format input to the
AUDIO (AES/EBU) IN 1/2 connector (optional DSBK-
1501 board required)
• SDI audio signal input to the SDI/SDTI (QSDI) IN
connector (optional DSBK-1501 board required)
• Audio test signal (selected with the INT AUDIO SG
generator
d CH2 3/4 button
c CH1 1/2 button
b VIDEO button
a SDTI/i.LINK button
a SDTI/i.LINK (SDTI (QSDI) interface/i.LINK
selection) button
Each press of this button cycles through the following
input signal selection options.
• Digital video signal in SDTI (QSDI) format input to the
SDI/SDTI (QSDI) IN connector (optional DSBK-1501
board required)
When this is selected, use the CH1 1/2 button and CH2
3/4 button to select the required input audio signals.
The selection made with this button is indicated by the
AUDIO CH-1 1/2 indicators in the INPUT signal display
When analog audio is selected (optional DSBK-1504/
1504P board required), the signal input to the AUDIO IN
1/3 connector is recorded either on channel 1 (when in 2-
channel mode) or on channels 1 and 3 (when in 4-channel
mode). That is, in 4-channel mode, the same analog audio
signal is recorded on channels 1 and 3. Using the REC/PB
LEVEL control knobs with the VAR switch set to REC, it
is possible to adjust the audio levels on the two channels
separately.
Note
In this case, the phases of the selected audio signals
will be about two frames ahead of the phase of the
digital video signal in SDTI (QSDI) format.
You can switch the audio recording mode with the REC
by the REC MODE display on the front panel.
• Digital video and audio signals in SDTI (QSDI) format
input to the SDI/SDTI (QSDI) IN connector (optional
DSBK-1501 board required)
• Digital video and audio signals in i.LINK-compatible
DV format input to the i.DV IN/OUT connector
The selection made with this button is indicated in the
d CH2 3/4 (audio channel 2 or 3/4) button
Each press of this button cycles through the following
input audio signal selection options for audio channel 2
(when in 2-channel mode) or for audio channels 3 and 4
(when in 4-channel mode).
• Analog audio signal input to the AUDIO IN 2/4
connector (optional DSBK-1504/1504P board required)
• Digital audio signal in AES/EBU format input to the
AUDIO (AES/EBU) IN 3/4 connector (optional DSBK-
1501 board required)
• SDI audio signal input to the SDI/SDTI (QSDI) IN
connector (optional DSBK-1501 board required)
• Audio test signal (selected with the INT AUDIO SG
generator
The selection made with this button is indicated by the
AUDIO CH-2 3/4 indicators in the INPUT signal display
When analog audio is selected (optional DSBK-1504/
1504P board required), the signal input to the AUDIO IN
2/4 connector is recorded either on channel 2 (when in 2-
channel mode) or on channels 2 and 4 (when in 4-channel
mode). That is, in 4-channel mode, the same analog audio
signal is recorded on channels 2 and 4. Using the REC/PB
LEVEL control knobs with the VAR switch set to REC, it
b VIDEO button
Each press of this button cycles through the following
input video signal selection options.
• Composite video signal input to the VIDEO IN
connector (optional DSBK-1504/1504P board required)
• S-video (separated Y and C) signals input to the VIDEO
IN connectors (optional DSBK-1504/1504P board
required)
• Y, R−Y and B−Y component video signals input to the
VIDEO IN connectors (optional DSBK-1504/1504P
board required)
• SDI video signal input to the SDI/SDTI (QSDI) IN
connector (optional DSBK-1501 board required)
• Video test signal (selected with the INT VIDEO SG
signal generator
The selection made with this button is indicated by the
Location and Function of Parts
15
Download from Www.Somanuals.com. All Manuals Search And Download.
is possible to adjust the audio levels on the two channels
separately.
You can switch the audio recording mode with the REC
by the REC MODE display on the front panel.
Location and Function of Parts
16
Download from Www.Somanuals.com. All Manuals Search And Download.
C Display section
d Time data type indicators
e SERVO indicator
f Recording/playback tape format indicators
g Cassette memory indicator
INPUT
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
VIDEO
AUDIO
V:SDTI COMPOSITE
SDTI
CH-1 1/2 CH-2 3/4
REPEAT
S VIDEO ANALOG ANALOG
i.LINK
Y-R,B
AES/EBU AES/EBU
SDI SG SDI SG SDI SG
OUTPUT
VIDEO
AUDIO
CH 1/2
CH 3/4
SDI COMPOSITE
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
SDTI
S VIDEO
VITC
REMOTE
9P i.LINK
Y-R,B
EDIT MODE
b OUTPUT signal display section
c Time counter display
a INPUT signal display section
h NO EDIT indicator
i CL indicator
j REC INHI indicator
k Tape end alarm indicator
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
REPEAT
l REPEAT indicator
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
VITC
REMOTE
m Remote mode indicators
9P i.LINK
EDIT MODE
q VITC indicator
p EDIT MODE indicator
o REC MODE display
n PB Fs display
a INPUT signal display section
V:SDTI indicator: Lights when the digital video signal
only in SDTI (QSDI) format is selected (optional
DSBK-1501 board required).
SDTI indicator: Lights when the digital video and audio
signals in SDTI (QSDI) format are selected (optional
DSBK-1501 board required).
Indicates the input video and audio signal formats selected
with the INPUT SELECT buttons (SDTI/i.LINK, VIDEO,
CH1 1/2, and CH2 3/4 buttons).
Note
The indicators without the corresponding optional boards
installed in the unit do not light.
i.LINKindicator: Lights when the digital video and audio
signals in i.LINK-compatible DV format are selected.
Location and Function of Parts
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO indicators: The indicator (COMPOSITE, S
VIDEO, Y−R,B, SDI, or SG) corresponding to the
selected input video signal format lights.
b
OUTPUT signal display section
Indicates the output video and audio signal format selected
Indicators
Meanings
Note
The indicators without the corresponding optional boards
installed in the unit do not light.
COMPOSITE Composite video signal (optional
DSBK-1504/1504P board required)
S VIDEO
S-video (separated Y and C) signals
(optional DSBK-1504/1504P board
required)
SDI indicator: Lights when the digital video and audio
signals in SDI format are selected (optional DSBK-
1501 board required).
Y−R,B
Y, R−Y and B−Y component video
signals (optional DSBK-1504/1504P
board required)
The SDI video and audio signals are output to the SDI/
SDTI (QSDI) OUT1 and OUT2 connectors.
SDI
SG
SDI video signal (optional DSBK-1501
board required)
SDTI indicator: Lights when the digital video and audio
signals in SDTI (QSDI) format are selected (optional
DSBK-1501 board required).
Video test signal (factory default
setting)
The video and audio signals in SDTI (QSDI) format
are output to the SDI/SDTI (QSDI) OUT1 and OUT2
connectors.
AUDIO indicators: Comprise the CH-1 1/2 indicator and
CH-2 3/4 indicator, under each of which there are four
more indicators (ANALOG, AES/EBU, SDI, and SG).
They indicate the selected input audio signal formats.
VIDEO indicators: The indicator (COMPOSITE, S
VIDEO, or Y−R,B) corresponding to the selected
output analog video signal format lights.
Indicators
CH-1 1/2
Functions
The indicator corresponding to the
Indicators
Meanings
(ANALOG, AES/ signal format selected for audio input
EBU, SDI, SG) to channel 1 (when in 2-channel
mode) or to channels 1 and 2 (when
in 4-channel mode) lights.
COMPOSITE Composite video signal
S VIDEO
S-video (separated Y and C) signals
Y−R,B
Y, R−Y and B−Y component video
signals
ANALOG: Analog audio signal
(optional DSBK-1504/1504P
board required)
This selection determines the signals output from the
Y/CPST, R−Y/C/CPST, and B−Y/CPST (SUPER)
connectors as follows.
AES/EBU: Digital audio signal in
AES/EBU format (optional
DSBK-1501 board required)
SDI: SDI audio signal (optional
• When COMPOSITE is selected:
DSBK-1501 board required)
SG: Audio test signal (factory default
setting)
Connectors
Y/CPST
Output signals
Composite signal
Composite signal
Composite signal
CH-2 3/4
The indicator corresponding to the
R−Y/C/CPST
B−Y/CPST (SUPER)
(ANALOG, AES/ signal format selected for audio input
EBU, SDI, SG) to channel 2 (when in 2-channel
mode) or to channels 3 and 4 (when
in 4-channel mode) lights.
• When S VIDEO is selected:
ANALOG: Analog audio signal
(optional DSBK-1504/1504P
board required)
AES/EBU: Digital audio signal in
AES/EBU format (optional
DSBK-1501 board required)
SDI: SDI audio signal (optional
DSBK-1501 board required)
Connectors
Y/CPST
Output signals
Y signal
R−Y/C/CPST
C signal
(3.58 MHz for DSR-1500A/
4.43 MHz for DSR-1500AP)
B−Y/CPST (SUPER)
Composite signal
SG: Audio test signal (factory default
setting)
• When Y–R,B is selected:
Connectors
Y/CPST
Output signals
Y signal
R−Y/C/CPST
B−Y/CPST (SUPER)
R−Y signal
B−Y signal
Location and Function of Parts
18
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO indicators: Comprise the CH 1/2 indicator and
CH 3/4 indicator to indicate the channel selection for
analog audio output from the AUDIO OUT 1/3 and
AUDIO OUT 2/4 connectors.
g
Cassette memory indicator
Lights when a cassette provided with a memory chip
(“cassette memory”) is loaded.
h NO EDIT (not editable) indicator
Indicators
CH 1/2
Functions
Lights when channels 1 and 2 are
selected for analog audio output from
the AUDIO OUT 1/3 and AUDIO OUT
2/4 connectors.
When the recording format setting is DVCAM
Lights during playback of a tape that contains a recording
in other than the DVCAM format. When this indicator is
lit, the recordings contained in the tape can be used as
source material for editing, but editing operations such as
insert editing and assemble editing cannot be performed.
This indicator also lights when the audio recording mode
selected on this unit does not coincide with that of the
loaded tape during editing operation.
CH 3/4
Lights when channels 3 and 4 are
selected for analog audio output from
the AUDIO OUT 1/3 and AUDIO OUT
2/4 connectors.
You can change the channel selection with the AUDIO
When the recording format setting is DV (SP)
Lights during playback of a tape that contains a recording
in DVCAM, DV, or DVCPRO format.
c Time counter display
Indicates the count value of the time counter, time code,
VITC, or user bit data depending on the settings of the
COUNTER SELECT button and the TC SELECT menu
i CL (ClipLink) indicator
Lights when a cassette is loaded on which ClipLink log
data is stored in the cassette memory.
Also used to display error messages, edit data, setup menu
data, etc.
For details of ClipLink log data, see the appendix
d Time data type indicators
One of the three indicators (COUNTER, U-BIT, or TC)
lights to indicate the type of time data currently shown in
the time counter display.
j REC INHI (recording inhibit) indicator
Lights when the REC/SAVE switch on the loaded cassette
is in the SAVE position (recording inhibited).
COUNTER: Count value of the time counter
U-BIT: User bit data
TC: SMPTE time code (for DSR-1500A) or EBU time
code (for DSR-1500AP)
k Tape end alarm indicator
Starts flashing when the remaining capacity of the tape is
for about 2 minutes.
e SERVO (servolock) indicator
Lights when the drum servo and capstan servo are locked.*
l REPEAT (repeat playback) indicator
Lights when the REPEAT MODE menu item (see page
64) is set to ON to enable the repeat playback function.
* Servolock: Synchronizing the drum rotation phase and tape transport
phase with a reference signal during playback and recording so that the
video heads scan the tape in the same pattern during playback and
recording.
m Remote mode indicators
REMOTE: Lights when the LOCAL/REMOTE switch is
set to REMOTE to remote control the unit from either
an editing control unit connected to the REMOTE
connector or equipment connected to the i.DV IN/
OUT connector.
f Recording/playback tape format indicators
DVCAM: This lights when recording or playback is
carried out in DVCAM format.
DV: This lights when recording or playback is carried out
in consumer DV format.
LP: This flashes along with “DV” when a tape recorded in
LP mode is played back.
73) is set to 9PIN.
page 73) is set to i.LINK.
Video recorded in LP mode cannot be played back
correctly and audio is muted.
When a tape recorded in DVCPRO (25 Mbps) format or
any other format than those mentioned above is played
back, none of the above indicators lights.
The recording format can be changed with the REC
setting of the recording format is DVCAM.
n PB Fs (playback audio sampling frequency) display
During playback, this indicates the playback audio mode
in which the tape being played back was recorded.
48K indicator: Lights during playback of a tape recorded
in 2-channel mode (48 kHz).
44.1K indicator: Lights during playback of a tape
recorded in 2-channel mode (44.1 kHz).
Location and Function of Parts
19
Download from Www.Somanuals.com. All Manuals Search And Download.
32K indicator: Lights during playback of a tape recorded
p
EDIT MODE indicator
in 4-channel mode (32 kHz).
Lights when this unit is selected as the recorder VCR
under the control of either an editing control unit
connected to the REMOTE connector or equipment
connected to the i.DV IN/OUT connector.
o REC MODE (audio recording mode) display
This indicates the audio recording mode currently selected
2CH indicator: Lights in 2-channel mode (48 kHz).
4CH indicator: Lights in 4-channel mode (32 kHz).
q VITC indicator
Lights when VITC is being read or recorded regardless of
the data shown in the time counter display.
D Tape transport control section
REW
PLAY
F FWD
STOP
REC
e REC button
d STOP button
c F FWD button
b PLAY button
a REW button
a REW (rewind) button
Note
When you press this button, it lights and the tape starts
rewinding.
When the F. FWD/REW menu item under the AUTO EE
appears on the monitor during rewind (maximum 85 times
normal speed).
When the LOCAL/REMOTE switch is set to REMOTE
(the REMOTE indicator is lit), no tape transport control
buttons other than the EJECT and STOP buttons will work.
This can be changed with the LOCAL ENABLE menu
b PLAY button
When you press this button, it lights and playback begins.
If you press this button during recording or editing, the
recording or editing operation is stopped and this unit
enters playback mode.
c F FWD (fast forward) button
When you press this button, it lights and the tape is fast
forwarded.
When the F. FWD/REW menu item under the AUTO EE
appears on the monitor during fast forward (maximum 85
times normal speed).
d STOP button
Press this button to stop the current tape transport
operation.
e REC (record) button
When you press this button while holding down the PLAY
button, it lights and recording begins.
Location and Function of Parts
20
Download from Www.Somanuals.com. All Manuals Search And Download.
e fFgG (arrow) buttons
E Menu control section
Use these buttons to move around the menu items, and also
to modify the initial time code value and user bit data.
set to ENABLE, you can also use these buttons to carry out
the following playback operations.
a MENU button
b RESET (NO) button
MENU
RESET(NO)
Playback type
Direction Operation to carry out
Playback in range Forward
Press the G button.
c TC PRESET button
TC
PRESET
10 times normal
SET(YES)
Reverse
Press the g button.
speed
d SET (YES) button
Frame-by-frame
playback
Forward
Reverse
Forward
Reverse
Press the f button.
Press the F button.
Continuous
playback in jog
mode
Hold down the f button.
Hold down the F button.
e fFgG buttons
For details on modifying the time code value, see “To set
a MENU button
Press this button to display the menu on the monitor screen
and the time counter display. Press it again to exit the menu
display.
b RESET (NO) button
Press this button to:
• reset menu settings,
• reset the time data shown in the time counter display to
zero, or
• send a negative response to the prompts issued by the
unit.
c TC (time code) PRESET button
Use this button to set the initial value of the time code
produced by the internal time code generator and user bit
data.
For details on setting an initial time code value and user
d SET (YES) button
Press this button to:
• save new settings, such as selected menu items and time
code settings, to memory, or
• send a positive response to the prompts issued by the
unit.
Location and Function of Parts
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
a AC IN connector
AC IN
AUDIO IN
1/3
VIDEO
IN
2/4
2/4
Y/CPST
R-Y/C
B-Y
A Analog video/audio signal
input section
(SUPER)
VIDEO OUT
R-Y/C/CPST B-Y/CPST
AUDIO OUT
1/3
MONITOR
REF.VIDEO
IN
Y/CPST
B Analogvideo/audiosignal
output section
IN
OUT1
OUT
OUT2 SDI/SDTI
(QSDI)
IN
AUDIO I/O (AES/EBU)
3/4 1/2
OUT
DV IN/OUT
b
DV IN/OUT connector
1/2
3/4
TC IN
REMOTE
C Digital signal input/output
section (see page 25)
c REMOTE connector
d REF. VIDEO IN connectors
a AC IN connector
Use the supplied power cord to connect this to an AC
outlet.
c REMOTE connector (D-sub 9-pin)
When controlling this unit from an editing control unit
such as the ES-7, PVE-500, BVE-600/800/910, or RM-
450/450CE, connect the editing control unit to this
connector using the optional 9-pin remote control cable.
b
DV IN/OUT connector (6-pin IEEE-1394)
This connector inputs and outputs digital video and audio
signals in DV format.
d REF. (reference) VIDEO IN connectors (BNC
type)
Input a reference video signal. The two connectors are
loop-through connectors. You can connect the reference
video signal input to the left connector to other equipment
Notes
• If the unit is connected to a device equipped with a 6-pin
DV jack, when you intend to disconnect or reconnect the
DV cable, turn off the device and pull out the plug of its
power cord from the AC outlet beforehand. If you
connect or disconnect the DV cable while the device is
connected to the AC outlet, high-voltage current (8 to 40
V) is output from the DV jack of the device to this unit,
which may cause a malfunction.
via the right connector (marked
). When no connection
is made to the right connector, the left connector is
terminated with an impedance of 75 Ω automatically.
• When connecting a device that has a 6-pin DV jack to
this unit, first connect the plug of the cable to the 6-pin
DV jack of the device.
1
1
• When searching at speeds in the range + / to + / or
2
30
1
1
− / to − / times normal speed, the audio signal output
30
2
from this connector and monitored on external
equipment may sound differently from the audio signal
played back on this unit.
Location and Function of Parts
22
Download from Www.Somanuals.com. All Manuals Search And Download.
A Analog video/audio signal input section (optional DSBK-1504/1504P Analog Input
Board)
The connectors in this section are available when the
optional DSBK-1504/1504P board is installed.
AC IN
AUDIO IN
1/3
VIDEO
IN
2/4
Y/CPST
R-Y/C
B-Y
a VIDEO IN connectors
b AUDIO IN 1/3 and AUDIO IN 2/4 connectors
a VIDEO IN connectors (BNC type)
When Y–R,B is selected:
There are the following VIDEO IN connectors for
inputting analog video signals:
• Y/CPST (loop-through connectors)
• R−Y/C
Connectors
Y/CPST
R−Y/C
Input signals
Y signal
R−Y signal
B−Y signal
• B−Y
B−Y
The signals you can connect to these connectors depend on
the selection made with the VIDEO button in the video/
audio input selection section. The selection is indicated by
the VIDEO indicators in the INPUT signal display section.
The analog video signals that can be input to these
connectors are as follows.
b AUDIO IN 1/3 and AUDIO IN 2/4 connectors
(XLR-3 pin, female)
Use these connectors to input analog audio signals from an
external video cassette player or other audio equipment.
The signals input to these connectors are recorded on the
audio channels determined by the current audio recording
mode, as follows.
When COMPOSITE is selected:
Connectors
Y/CPST
R−Y/C
Input signals
Composite signal
— (not usable)
— (not usable)
When in 2 CH (48 kHz) mode:
Input
connectors
Audio channels on which input
signals are recorded
B−Y
AUDIO IN 1/3
AUDIO IN 2/4
Audio channel 1
Audio channel 2
The two Y/CPST connectors are loop-through
connectors. When using the signal input to the left Y/
CPST connector as a reference video signal, for
example, you can bridge-connect the signal to other
equipment via the right Y/CPST connector (marked
). When no connection is made to the right Y/
CPST connector, the left Y/CPST connector is
terminated with an impedance of 75 Ω automatically.
When in 4 CH (32 kHz) mode:
Input
Audio channels on which input
connectors
signals are recorded
Audio channels 1 and 3
Audio channels 2 and 4
AUDIO IN 1/3
AUDIO IN 2/4
When S VIDEO is selected:
You can switch the audio recording mode with the REC
by the REC MODE display on the front panel.
Connectors
Y/CPST
Input signals
Y signal
R−Y/C
C signal
(3.58 MHz for DSR-1500A/
4.43 MHz for DSR-1500AP)
B−Y
— (not usable)
Location and Function of Parts
23
Download from Www.Somanuals.com. All Manuals Search And Download.
B Analog video/audio signal output section
a VIDEO OUT connectors
b AUDIO OUT 1/3 and AUDIO OUT 2/4 connectors
(SUPER)
VIDEO OUT
R-Y/C/CPST B-Y/CPST
AUDIO OUT
MONITOR
2/4
1/3
Y/CPST
c MONITOR connector
a VIDEO OUT connectors (BNC type)
There are the following VIDEO OUT connectors for
outputting analog video signals:
When Y–R, B is selected:
Connectors
Y/CPST
Output signals
Y signal
• Y/CPST
• R−Y/C/CPST
• B−Y/CPST (SUPER)
R−Y/C/CPST
R−Y signal
B−Y signal
B−Y/CPST
(SUPER)
The signals output from these connectors depend on the
The setting is indicated by the VIDEO indicators in the
OUTPUT signal display section on the front panel.
The analog video signals that can be output from these
connectors are as follows.
b AUDIO OUT 1/3 and AUDIO OUT 2/4 connectors
(XLR-3 pin, male)
These connectors output analog audio signals. The output
audio channels are determined by the playback audio mode
and the setting (1/2 CH or 3/4 CH) of the AUDIO
When COMPOSITE is selected:
Connectors
Y/CPST
Output signals
Composite signal
Composite signal
Composite signal
When in 2 CH (48 kHz or 44.1 kHz) mode:
Output
connectors
Output audio channels
R−Y/C/CPST
B−Y/CPST
(SUPER)
AUDIO OUT 1/3 Audio channel 1 (when 1/2 CH is
selected) or silent (when 3/4 CH is
selected)
When the CHARA. DISPLAY menu item (see page
CPST (SUPER) connector outputs a composite video
signal with superimposed text information.
AUDIO OUT 2/4 Audio channel 2 (when 1/2 CH is
selected) or silent (when 3/4 CH is
selected)
When in 4 CH (32 kHz) mode:
When S-VIDEO is selected:
Output
connectors
Output audio channels
Connectors
Y/CPST
Output signals
Y signal
AUDIO OUT 1/3 Audio channel 1 (when 1/2 CH is
selected) or audio channel 3 (when 3/
4 CH is selected)
R−Y/C/CPST
C signal
(3.58 MHz for DSR-1500A/
4.43 MHz for DSR-1500AP)
AUDIO OUT 2/4 Audio channel 2 (when 1/2 CH is
selected) or audio channel 4 (when 3/
4 CH is selected)
B−Y/CPST
(SUPER)
Composite signal
The current playback audio mode is indicated by the PB Fs
display on the front panel.
When the CHARA. DISPLAY menu item (see page
CPST (SUPER) connector outputs a composite video
signal with superimposed text information.
c MONITOR connector (RCA phono jack)
This connector outputs audio signals for monitoring. The
audio signals to be output from this connector can be
selected with the MONITOR SELECT button and
METER CH-1/2 3/4 button on the front panel.
Location and Function of Parts
24
Download from Www.Somanuals.com. All Manuals Search And Download.
C Digital signal input/output section (optional DSBK-1501 Digital Input/Output Board)
The connectors in this section are available when the
optional DSBK-1501 board is installed.
a SDI/SDTI (QSDI) IN connector
b SDI/SDTI (QSDI) OUT1/OUT2 connectors
c AUDIO (AES/EBU) IN 1/2 and AUDIO (AES/EBU)
IN 3/4 connectors
d AUDIO (AES/EBU) OUT 1/2 and AUDIO
(AES/EBU) OUT 3/4 connectors
IN
OUT1
OUT2 SDI/SDTI
(QSDI)
IN
AUDIO I/O (AES/EBU)
3/4 1/2
OUT
1/2
3/4
a SDI/SDTI (QSDI) IN (Serial Digital Interface/
Serial Data Transport Interface (QSDI) input)
connector (BNC type)
This connector inputs digital video and audio signals in
SDTI (QSDI) or SDI format. To select the required input
signal formats, use the SDTI/i.LINK button or VIDEO
button on the front panel. The current input signal
selections are indicated in the INPUT signal display
section on the front panel.
d AUDIO (AES/EBU) OUT 1/2 and AUDIO (AES/
EBU) OUT 3/4 connectors (BNC type)
These connectors output digital audio signals in AES/EBU
format.
The left connector (1/2) is for audio channels 1 and 2, and
the right connector (3/4) is for audio channels 3 and 4.
D Time code input/output section
b SDI/SDTI (QSDI) OUT1/OUT2 (Serial Digital
Interface/Serial Data Transport Interface (QSDI)
output 1/output 2) connectors (BNC type)
a TC IN connector
b TC OUT connector
These connectors output digital video and audio signals in
SDTI (QSDI) or SDI format. To select these output signal
formats, use the DIGITAL OUTPUT menu item (see page
73). The current output signal selections are indicated in
the OUTPUT signal display section on the front panel.
TC IN
OUT
Note
a TC IN (time code input) connector (BNC type)
Input externally generated SMPTE time code (for DSR-
1500A) or EBU time code (for DSR-1500AP) to this
connector.
1
1
When searching at speeds in the range + / to + / or
2
30
1
1
− / to − / times normal speed, the audio signal output
2
30
from these connectors in SDTI (QSDI) format and
monitored on external equipment may sound differently
from the audio signal played back on this unit.
b TC OUT (time code output) connector (BNC type)
This connector outputs a time code according to the
operating state of the unit, as follows:
c AUDIO (AES/EBU) IN 1/2 and AUDIO (AES/
EBU) IN 3/4 connectors (BNC type)
Input digital audio signals in AES/EBU format to these
connectors.
The left connector (1/2) is for audio channels 1 and 2, and
the right connector (3/4) is for audio channels 3 and 4.
During playback: the playback time code
During recording: the time code generated by the internal
time code generator or the time code input to the TC
IN connector. When the EE OUT PHASE menu item
(see page 69) is set to MUTE, no time code is output.
Location and Function of Parts
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording and Playback Chapter
2
Usable Cassettes
This unit can use the DVCAM cassettes listed below.
Model name
Size
PDV-64ME/94ME/124ME/184ME
PDVM-12ME/22ME/32ME/40ME
Standard size
Mini size
The numbers in each model name indicate the maximum recording/playback
time (in minutes) for each model. For example, the PDV-184ME has a
maximum recording/playback time of 184 minutes.
Cassettes usable for playback only
All consumer DV cassettes and large- and medium-size DVCPRO (25 Mbps)
cassettes are usable for playback only.
Notes
• If you insert an incorrect type of cassette, it will be automatically ejected.
• When operating this unit as a player, you can also use DV cassettes on the
unit. However, it is the best choice to always use DVCAM cassettes because
they are more reliable than DV cassettes whatever your purpose may be:
playback, editing, or long-period storage of recordings.
• Cassettes that have been recorded by a DV-format recorder can be played
back on this unit but cannot be used for recording at editing operation. When
you insert such a cassette into this unit, the NO EDIT indicator lights up in the
display section on the front panel of this unit.
Usable Cassettes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVCAM cassettes
The following figure illustrates the DVCAM cassettes.
REC/SAVE switch
Mini size
Standard size
Cassette memory
This memory is used to store ClipLink log data.
For details of ClipLink log data, see the appendix
Notes on using cassettes
• Before storing the cassette for a long period of time, rewind the tape to the
beginning and be sure to put the cassette in its storage case, preferably on end
instead of flat on its side.
Storing a cassette in any other condition (not rewound, out of its case, etc.)
may cause the video and audio contents to become damaged over time.
• If the cassette memory connector (contact point) becomes dirty, connection
problems may occur, causing a loss of functions. Remove away any dust or
dirt from this area before using the cassette.
• If the cassette is dropped on the floor or otherwise receives a hard impact, the
tape may become slackened and may not record and/or play back correctly.
For information about how to check the tape for slack, see the next section.
Checking the tape for slack
Using a paper clip or a similar object, turn the reel gently in the direction shown
by the arrow. If the reel does not move, there is no slack. Insert the cassette into
the cassette compartment, and after about 10 seconds take it out.
Paper clip, etc.
Reel
Usable Cassettes
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Preventing accidental erasure
Set the REC/SAVE switch on the cassette to SAVE to prevent accidental
erasure of recorded contents.
REC/SAVE switch
Set to SAVE
REC
SAVE
To enable re-recording
Set the REC/SAVE switch to REC.
When this switch is set to SAVE, the unit cannot record on the tape.
Inserting and Ejecting Cassettes
Inserting a cassette
This unit accepts three sizes of cassette: L (standard size), M (medium size:
DVCPRO) and S (mini size). When inserting a cassette in the unit, make sure
its tape window faces upward as shown in the following figure.
Outer guides
Mini size (Insert the cassette into the
middle of the cassette compartment.)
Standard size
Tape window facing upward
Inner guides
Medium size (Align the cassette with
the outer guides, then slide it in over
the inner guides.)
Tape window facing upward
Usable Cassettes
29
Download from Www.Somanuals.com. All Manuals Search And Download.
No double insertion of cassettes
When you insert a cassette, the orange lock-out plate appears in the cassette
compartment to prevent double insertion.
Ejecting a cassette
Press the EJECT button.
EJECT button
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
i.LINK
-20
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
PB
F
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
48K 44.1K 32K
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
Usable Cassettes
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
This section describes the necessary settings and operations to perform
recording on this unit. The same settings and operations apply whether you are
using the unit as part of an editing system, for dubbing, or as a stand-alone
recorder.
For the necessary connections for recording and the settings not covered in this
For dubbing of SDTI (QSDI) format signals, use the AUTO FUNCTION menu
For this unit, recording in DVCAM format is recommended, but recording in
DV (SP mode only) format is also possible.
Notes
• When carrying out multiscene continuous recording on a DV (SP) tape using
this unit with an optional remote control unit such as the DSRM-10, on rare
occasions, the video may be disrupted at the IN point of the first scene or the
audio may be muted due to a REC MODE (audio recording mode) difference
between the tape and this unit.
There may also be cases in which the unit is subjected to some functional
restrictions attributable to the use of the DV format.
• When using the unit as an editor, the optional boards corresponding to the
input signal formats to be used are required.
Recording
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Recording
Player (DSR-1600/1600P, etc.)
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
2
1
Video monitor
INPUT signal display
section
LOCAL/REMOTE
switch
Recorder (DSR-1500A/1500AP)
3
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
-20
i.LINK
6
4
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
7
HOURS
PB FS
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
48K 44.1K 32K
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
5
Audio level meters
When controlling this unit from an editing control unit connected to the
1 Power on the video monitor, then set its input switches according to the
signals input from this unit.
2 Set up the player to play back a tape.
For details, refer to the operating instructions for the player.
3 Power on this unit by pressing on the side of the POWER switch.
4 When the REMOTE indicator is off (the external editing control unit is not
used), use the COUNTER SELECT button to select the type of time data to
be used.
Each press of this button cycles through three options: COUNTER (CNT
value), TC (time code), and U-BIT (user bit data). The time data type
indicator for each option lights as it is selected.
Selected time data
Count value of the time counter
Time code
Time data type indicator
COUNTER
TC
User bit data
U-BIT
Recording
32
Download from Www.Somanuals.com. All Manuals Search And Download.
When the REMOTE indicator is lit, selection of the time data type is carried
out at the editing control unit.
5 Select the formats of video and audio input signal to be recorded.
Use the INPUT SELECT buttons in the video/audio input setting section to
select the desired signal formats. Each selection is shown by a lit indicator
in the INPUT signal display section.
Video input signal
(input connector)
Corresponding INPUT Lit indicator in the
SELECT button
INPUT signal display
a)
section
Composite signal
(VIDEO IN: Y/CPST)
VIDEO
VIDEO
COMPOSITE in VIDEO
group
Separated Y/C signal
(VIDEO IN: Y/CPST and
R−Y/C)
S VIDEO in VIDEO
group
Component signal
(VIDEO IN: Y/CPST,
R−Y/C, and B−Y)
VIDEO
Y−R,B in VIDEO group
SDI signal
VIDEO
SDI in VIDEO group
(SDI/SDTI (QSDI) IN)
SDTI (QSDI) signal
(SDI/SDTI (QSDI) IN)
SDTI/i.LINK
SDTI: both SDTI video
and audio input
signals are
recorded.
V:SDTI: only SDTI video
input signal is
recorded.
i.LINK-compatible digital SDTI/i.LINK
video signal in DV format
(i.DV IN/OUT)
i.LINK
Internal test video signal VIDEO
SG in VIDEO group
a) The indicators without the corresponding optional boards (DSBK-1501/1504/1504P) installed in
the unit do not light.
Audio input signal
(input connector)
Corresponding INPUT Lit indicator in the
SELECT button
INPUT signal display
a)
section
Analog signal
(AUDIO IN 1/3 and
AUDIO IN 2/4)
CH1 1/2 and CH2 3/4
ANALOG in AUDIO
group
AES/EBU signal
(AUDIO (AES/EBU) IN)
CH1 1/2 and CH2 3/4
CH1 1/2 and CH2 3/4
SDTI/i.LINK
AES/EBU in AUDIO
group
SDI signal
(SDI/SDTI (QSDI) IN)
SDI in AUDIO group
SDTI (QSDI) signal
SDTI
(SDI/SDTI (QSDI) IN)
i.LINK-compatible digital SDTI/i.LINK
audio signal in DV format
(i.DV IN/OUT)
i.LINK
Internal test audio signal CH1 1/2 and CH2 3/4
SG in AUDIO group
a) The indicators without the corresponding optional boards (DSBK-1501/1504/1504P) installed in
the unit do not light.
Caution
Once you have started recording, you cannot change the input signal
selection.
Recording
33
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Select the audio mode.
Select either two-channel mode (2 CHANNEL) or four-channel mode (4
corresponding indicator lights in the REC MODE display.
Audio mode
Lit indicator in the REC MODE display
2-channel mode
4-channel mode
2CH
4CH
Cautions
• When recording in DVCAM format or this unit’s DV (SP) format, two
audio recording modes, with either two channels at 48 kHz or four
channels at 32 kHz, can be used. It is not possible to select any other mode
(for example with four channels at 48 kHz).
• During audio editing, if a signal used in assemble or insert editing is in a
different mode from the base tape, the signals will be discontinuous at the
edit points, and correct editing will not be obtained. For this reason, the
menu settings on this unit are arranged to inhibit audio editing between
different modes.
For smooth editing operations, check the audio recording mode of the
base tape beforehand.
• Once you have started recording, you cannot change the audio mode or
recording format.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
• When, in 4-channel mode, analog audio is selected for all four channels
(channels 1/2 and 3/4), the same analog audio signals are recorded on
channels 1 and 3 and on channels 2 and 4, respectively.
7 When manually adjusting audio input levels
With the VAR switch on the front panel set to REC, use the REC/PB
LEVEL control knob for each channel to adjust the audio input level.
Watching the audio level meter in E-E mode, adjust the level so that the
meter does not indicate higher values than 0 dB when the audio signal is at
its maximum. When the level exceeds 0 dB, the OVER indicator lights.
When recording at reference level
When the VAR switch on the front panel is set to PRESET, recording is
carried out at the preset reference level.
Reference level setting
The factory-preset reference level for analog audio input is −20 dB (DSR-
1500A) or −18 dB (DSR-1500AP). This setting can be changed using the
For recording in DV (SP) format, the reference level is fixed at −12 dB.
Recording Procedure
This section describes the procedure to perform recording on this unit, showing
an example session in which playback signals coming from a player VCR will
be recorded on the tape loaded in the unit.
Recording
34
Download from Www.Somanuals.com. All Manuals Search And Download.
1
LOCAL/REMOTE
switch
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-12
-20
i.LINK
-20
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
Recorder
(DSR-1500A/1500AP)
2
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
Player
(DSR-1600/1600P, etc.)
3
Notes
• When controlling this unit from an editing control unit connected to the
REMOTE connector of this unit, set the LOCAL/REMOTE switch to
REMOTE, turning the REMOTE indicator on. When not, set the switch to
LOCAL, turning the indicator off.
• If you intend to use a tape recorded on this unit in a system comprising a DSR-
85/85P and an ES-7 EditStation, it is recommended to record color bars on at
least the first 40 seconds of the tape.
When transferring digital signals from the DSR-85/85P to the ES-7
EditStation at four times normal speed, there must be recording for
approximately 40 seconds before the IN point.
1 After checking the following items, hold the cassette with the tape window
facing upward, then insert it into the recorder (this unit) as illustrated on
.
Item to check
See section
of the cassette is set to REC.
Check for tape slack.
not shown in the time counter display.
The cassette is automatically drawn into the unit and the tape is wound
round the head drum. The tape is stationary while the head drum rotates, and
the STOP button lights.
Recording
35
Download from Www.Somanuals.com. All Manuals Search And Download.
If the REC INHI indicator lights:
It indicates that the REC/SAVE switch of the loaded cassette has been set
to SAVE. Press the EJECT button in the tape transport control section to
remove the cassette, then set the REC/SAVE switch to REC and reload the
cassette.
Note
When ejecting and loading cassettes, make sure that the unit has been
powered on.
2 Hold down the REC button and press the PLAY button.
This puts the unit into recording mode, and the tape starts moving.
3 Press the PLAY button on the player.
The player starts the playback operation, at which point this unit starts
recording the input playback signals.
Cautions
• Once you have started recording, you cannot change the audio mode or
recording format.
• If on a tape there is a point where the audio mode is switched, it is not
possible to carry out insert editing over a section including that point.
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
CL indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
Caution
With such a cassette, carrying out recording destroys
the ClipLink log data.
NO EDIT indicator
• The recording format of the tape is DV, or a
DVCPRO tape is inserted.
Replace the tape with one that has been recorded
in DVCAM format.
• The recording format selected on this unit is DV
(SP). In this case, you cannot use the editing
functions.
During editing operation
The audio recording mode selected on this unit does
not coincide with that of the tape.
In this case, set the unit for the same audio recording
mode as with the tape.
However, If your current purpose is recording only,
you can use the tape as it is.
Recording
36
Download from Www.Somanuals.com. All Manuals Search And Download.
To perform the following operations
Operation
Do this:
Stop recording.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time period set
tape protection.
Remove the cassette.
Press the EJECT button.
After a few seconds, the tape is unwound from the
head drum and the cassette is automatically ejected.
If a CNT value is shown on the time counter display
(the time data type indicator “COUNTER” is lit), the
CNT value is reset.
Inhibit the unit from
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
Referece level for recording in DV (SP) format
On many consumer DV devices, recording is carried out at a reference level of
−12 dB. Threfore, when recording in DV (SP) format on this unit, using the
fixed referenced level of −12 dB is recommended. When dubbing DVCAM
source material recorded at a different reference level, you can carry out manual
adjustment as described in the following.
a)
a)
Player (DSR-1800/1800P/1600 /1600P /
1500A/1500AP)
Recorder (DSR-1500A/
1500AP)
in E-E mode
in E-E mode
REC FORMAT: DV (SP)
Audio input selection: INT SG/1
i.LINK/
SDTI (QSDI)/
SDI
VAR switch: REC
kHz
REC mode: 2ch or 4ch depending
on DVCAM source
For each channel, observing
the audio level meter, adjust
the audio level to −12 dB
with the level control knob.
Reference level: Reference level
of the DVCAM source
b)
VAR switch : PRESET
a) On the DSR-1600/1600P, tape recorded at
the reference level is played back.
b) DSR-1500A/1500AP only
Recording
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
This section describes the settings and operations necessary to performplayback
on this unit. The same settings and operations apply whether you are using the
unit as part of an editing system, for dubbing, or as a stand-alone player VCR.
For the necessary connections for playback and the settings not covered in this
Settings for Playback
Video monitor
2
Player (DSR-1500A/1500AP)
1
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
i.LINK
-20
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
PB
F
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
48K 44.1K 32K
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
1 Power on this unit by pressing on the side of the POWER switch.
2 Power on the video monitor and set its switches as shown below.
Switch
Setting
75 Ω termination switch
Input switch
ON (or attach a 75 Ω terminator.)
Set according to the type of input signal from this
unit.
Playback
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Procedure
1
LOCAL/
REMOTE switch
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
-20
i.LINK
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
2
Note
When controlling this unit from an editing control unit connected to the
REMOTE connector of this unit, set the LOCAL/REMOTE switch of this unit
to REMOTE, turning the REMOTE indicator on. When not, set the switch to
LOCAL, turning the indicator off.
1 Insert a cassette.
The cassette is automatically drawn into the unit and the STOP button
lights. A few seconds later, if the STOP menu item under the AUTO EE
the monitor screen.
2 Press the PLAY button.
This starts the playback operation. When the tape is played back all the way
to the end, the unit automatically rewinds it and then stops.
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
CL indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
NO EDIT indicator
• The tape was recorded in the DV format, or a
DVCPRO tape is inserted.
You cannot use it as a recording tape for editing.
• The recording format selected on this unit is DV
(SP).
Playback
39
Download from Www.Somanuals.com. All Manuals Search And Download.
To perform the following operations
Operation
Do this:
Stop playback.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time set with the
protection.
Adjust the audio playback For digital (optional DSBK-1501 required) or
level.
analog audio output
Set the VAR switch on the front panel to PB and use
the REC/PB LEVEL control knob for each channel.
For outputs from the PHONES connector and
MONITOR connector
Use the PHONES control knob on the front panel
(outputs from the PHONES connector on the front
panel and the MONITOR connector on the rear panel
are adjusted).
Play back in shuttle mode To carry out a high-speed search (10 times normal
while monitoring the
video.
speed) in forward or reverse direction, press the G or
g button.
To return to normal-speed playback, press the PLAY
button.
a)
Note
When performing these operations, set the LOCAL/
REMOTE switch on the front panel to LOCAL.
Play back in jog mode while To carry out frame-by-frame playback in forward or
a)
reverse direction, press the f or F button.
When you hold down the f or F button, playback is
monitoring the video.
1
continued in jog mode (− / times normal speed) in
2
forward or reverse direction.
Note
When performing these operations, set the LOCAL/
REMOTE switch on the front panel to LOCAL.
Inhibit the unit from
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Remove the cassette.
Press the EJECT button.
If a CNT value is shown in the time counter display,
the CNT value is reset.
Disable the automatic
rewind function.
DISABLE.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
Playback
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback—Automatic Cyclical Playback
Proceed as follows to perform automatic cyclical playback of recording (repeat
playback) between selected start and end points.
1 Set the desired repeat start and end points with the REPEAT FUNCTION
You can set points A and B as start and end points by following the
procedure described in the next section.
The REPEAT indicator lights.
3 Press the SET (YES) button to save the new setting and close the menu.
4 Press the PLAY button.
The unit repeats playback between the repeat start and end points set in step
1.
Setting Points A and B for Repeat Playback
You can set the repeat playback start point (point A) and end point (point B) by
using the current tape position or inputting time code values.
To perform repeat playback after setting points A and B, press the PLAY button
when the REMOTE indicator is off. When the DSRM-10 Remote Control Unit
is connected to the CONTROL S connector on the front panel, you can also start
repeat playback by pressing its PLAY button with the REMOTE indicator of
this unit off.
Note
When performing repeat playback using points A and B as the playback start
and end points, make sure that the REPEAT TOP and REPEAT END menu
Playback
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the current tape position as point A or B
Proceed as follows to set the current tape position as point A or B for repeat
playback.
MENU
RESET(NO)
SET(YES)
TC
PRESET
dB OVER
0
dB OVER
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-12
i.LINK
-20
-20
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
Y-R,B
EDIT MODE
REW
PLAY
F
FWD
STOP
REC
Buttons used for setting
the current tape position
as point A
Buttons used for setting
the current tape position
as point B
While holding down the SET (YES) button in the menu control section, press
the gor Gbutton. The time code value of the current tape position is set as point
A or B, and a message “A set” or “B set” is displayed for 0.5 second in the time
counter display.
Once set, the point A or B time code value is held in the non-volatile memory
of the unit until changed. It is not lost when the unit is powered off.
Note
When setting point A or B, you can only use a time code value. Even when
COUNTER is selected with the COUNTER SELECT button, you cannot use a
CNT value to set point A or B.
To check the point A or B time code value
Press the g or G button in the menu control section. While the button is held
down, the point A or B time code value is displayed on the monitor and in the
time counter display.
If you hold down the g and G buttons simultaneously, the value shown is the
point B time code value minus the point A time code value. If the point A time
code value is greater than the point B time code value, a minus sign (−) is shown
before the value.
Playback
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Inputting time code values for points A and B
Using the following procedure, you can modify the time code value for point A
or B.
MENU
RESET(NO)
1,15
8,11
TC
PRESET
SET(YES)
13
12
2,3,4,6,10,11
5,7,9,12
1 Press the MENU button.
The following menu display appears.
SYSTEM MENU
SETUP MENU
Setup menu
Time counter display
AUTO FUNCTION
HOURS METER
Monitor screen
2 With “SETUP MENU” selected, press the G button.
The display changes as follows.
SETUP MENU
Operational
Time counter display
OPERATIONAL FUNCTION
DISPLAY CONTROL
TIME CODE
SETUP BANK OPERATION
MENU GRADE
:BASIC
Monitor screen
Playback
43
Download from Www.Somanuals.com. All Manuals Search And Download.
3 With “OPERATIONAL FUNCTION” selected, press the G button.
The display changes as follows.
SETUP MENU
>REP FUNC
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
AUTO EE SELECT
LOCAL ENABLE :STP&EJ
Monitor screen
4 With “REPEAT FUNCTION” selected, press the G button.
The contents of the REPEAT FUNCTION menu item are displayed.
SETUP MENU
>> REPEAT MD
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
:OFF
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:
T.TOP
V.END
:
B PRESET
Monitor screen
5 Press the F button to select “REPEAT TOP.”
SETUP MENU
>> REP TOP
Time counter display
OPERATIONAL FUNCTION
REPEAT FUNCTION
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:OFF
:T.TOP
:V.END
B PRESET
Monitor screen
Playback
44
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press the G button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> Tape top
Time counter display
:T.TOP
REPEAT TOP
* TAPE TOP
A POINT
:V.END
Monitor screen
7 Press the F button to select “A POINT.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> A point
Time counter display
REPEAT TOP
:T.TOP
* TAPE TOP :V.END
A POINT
Monitor screen
8 Press the g button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> REP TOP
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
Playback
45
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Press the F button to select “A PRESET.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> A preset
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
10Press the G button.
The A PRESET MODE screen appears. The time code value of the current
point A is displayed below the screen title.
A PRESET MODE
A 00:00:00:00
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE :
SET KEY
TO MENU : MENU KEY
Monitor screen
11Use the gor G button to select the digit in the time code value display that
you want to change.
Each press of the button causes the digit to the left or right to begin flashing.
Holding the button down moves the flashing digit continuously.
If you want to clear the time code value, press the RESET (NO) button. The
value is cleared to 00:00:00:00, and the leftmost digit begins flashing.
12Press the f or Fbutton to increment or decrement the value of the flashing
digit.
Each press of the button increments or decrements the value. Holding the
button down increments or decrements the value continuously. To change
other digits, return to step 11.
Playback
46
Download from Www.Somanuals.com. All Manuals Search And Download.
13Press the SET (YES) button to confirm the defined value.
The message “NOW SAVING...” is displayed on the monitor screen and
“Saving...” is shown in the time counter display while the new setting is
being saved in memory.
Caution
The new setting may be lost if you power off the unit during the saving
operation. Wait until the saving operation is completed before powering the
unit off.
If you want to discard the changed value
Press the MENU button instead of pressing the SET (YES) button to return
to the menu display, then press the MENU button again to end the menu
operation without saving the changed value into memory.
After the saving operation is completed, the monitor screen and time
counter display return to the REPEAT FUNCTION setting display as
shown in step 9.
14To set point B, refer to steps 5 to 13. (Select “REPEAT END” in step 5, “B
POINT” in step 7, and “B PRESET” in step 9.)
15Press the MENU button to close the menu.
Cuing Up to Any Desired Position Set as Point A or B
You can set any desired tape position as point A or B and cue up to the set point
when required. To cue up to point A or B, holding down the g or G button in
the menu control section, press the REW button in the tape transport control
section.
For the methods of setting points A and B, see the previous section.
Playback
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Convenient Functions
for Editing Operation Chapter
3
Use the DISPLAY CONTROL menu items (see page 66)
to select the information displayed and the character type
and position of the indications.
Setting the Time Data
When you set the SUB STATUS menu item (see page 67)
to other than OFF, you can also display supplementary
status information on the monitor screen such as editing
mode settings and the operating mode of the internal time
code generator.
This unit is provided with the following functions related
to time data.
• Display and reset CNT value
• Set, display, record, and play back SMPTE/EBU time
code and user bit data
• Set, display, record, and play back VITC
For details of supplementary status information, see
82.
The unit can output the time code read from the tape as an
analog (LTC) signal while in normal-speed playback
mode, and receive an external analog time code (LTC)
signal.
Note
The unit outputs no signal from the TC OUT connector
unless it is in normal-speed playback mode.
The following explains how to use these functions.
Displaying Time Data and Operation
Mode Indications
Time data and operation mode indications can be
displayed on the monitor screen.
Time data can also be displayed in the time counter display
on this unit.
To view time data and operation mode
indications on the monitor screen
ON (factory default setting).
The time data and the indication of the current operation
mode are superimposed on the video signal that is being
output from the B−Y/CPST (SUPER) connector, and can
be viewed on the monitor screen.
Setting the Time Data
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor screen contents
The contents of the monitor screen are shown below.
C Drop frame indication for time code generator
(for DSR-1500A only)
.
:
Drop frame mode (factory default setting)
Non-drop frame mode
A Time data type
Time data
D VITC field indication
B Drop frame indication
a)
for time code reader
(blank)
Display fields 1 and 3.
Display fields 2 and 4.
C Drop frame indication
*
for time code
a)
generator
D VITC field
E DSR-1500A/1500AP operation mode
indication
.
.
T C R
0 0
:
0 4
4 7
0 7
*
Display
Operation mode
P L A Y
L O C K
CASSETTE OUT
THREADING
UNTHREADING
STANDBY OFF
T. RELEASE
STOP
Cassette is not loaded.
Tape loading
E DSR-1500A/1500AP operation mode
Tape unloading
a) This character (.) can appear on the DSR-1500A only. The
character to appear in these two columns is always a colon
( : ) on the DSR-1500AP.
Standby off mode
Tape tension released
Stop mode
A Time data type
The following time data type indications are displayed.
F. FWD
Fast forward mode
REW
Rewind mode
Indication
CNT
Description
PREROLL
PLAY
Preroll mode
Count value of the time counter
Playback mode (servo unlocked)
Playback mode (servo locked)
Temporary stop of playback
Record mode (servo unlocked)
Record mode (servo locked)
Temporary stop of recording
Edit mode (servo unlocked)
Edit mode (servo locked)
Still picture in jog mode
Jog mode in forward direction
Jog mode in reverse direction
Shuttle mode
TCR
Time code data from time code reader
(factory default setting)
PLAY LOCK
PLAY-PAUSE
REC
UBR
User bit data from time code reader
a)
TCR.
Time code data from VITC reader
REC LOCK
REC-PAUSE
EDIT
a)
UBR.
User bit data from VITC reader
TCG
UBG
Time code data from time code generator
User bit data from time code generator
EDIT LOCK
JOG STILL
JOG FWD
JOG REV
SHUTTLE (Speed)
AUTO EDIT
PREVIEW
REVIEW
b)
Time code data from time code reader. The
asterisk indicates an interpolation by the time
code reader to make up for the time code
data not correctly read from the tape.
T*R
b)
User bit data from the time code reader. The
asterisk indicates that last data is retained by
the time code reader, as the new data has
not been read correctly from the tape.
U*R
Automatic editing mode
Preview mode
Review mode
a) You can switch between TC and VITC using the TC SELECT menu item
b) “*” is displayed when data cannot be read in correctly.
BDrop frame indication for time code reader (on
DSR-1500A only)
.
:
Drop frame mode (factory default setting)
Non-drop frame mode
Setting the Time Data
50
Download from Www.Somanuals.com. All Manuals Search And Download.
To reset the CNT value
Press the RESET (NO) button in the menu control section.
This resets the CNT value to 0:00:00:00.
To display the desired time data in the time
counter display
Note
During playback, if the recording on the tape includes
discontinuities, the counter may operate incorrectly at the
corresponding points.
Time data type indicators
Using the Internal Time Code
Generator
OVER
OVER
dB
0
dB
0
INPUT
VIDEO
REC INHI
U-BIT SERVO
TC COUNTER
CL
NO EDIT
AUDIO
You can set the initial time code value before recording the
time code generated by the internal time code generator
onto a tape. In addition, you can use the user bits to record
such data as the date, time, scene number, reel number, or
other useful information.
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
-20
i.LINK
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
Y-R,B
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
EDIT MODE
When an external time code generator is connected to the
TC IN connector, the internal time code generator can be
locked to (synchronized with) an external time code.
COUNTER SELECT button
Time counter display
To set the initial time code value and user
bit data
Press the COUNTER SELECT button on the front panel.
Each press of this button cycles through three options:
CNT value, time code, and user bit data. The time data type
indicator for each option lights as it is selected.
3 2
7
Time data
type
indicator
Time data shown in the time counter
display
OVER
OVER
dB
0
dB
0
INPUT
VIDEO
REC INHI
CL
NO EDIT
U-BIT SERVO
TC COUNTER
AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
REPEAT
SDTI
S
VIDEO ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SDI SG SDI SG SDI SG
-12
-20
-12
-20
i.LINK
COUNTER
TC
CNT (count value of the time counter)
OUTPUT
VIDEO
SDI COMPOSITE
SDTI VIDEO
Y-R,B
-30
-40
-30
-40
AUDIO
CH 1/2
CH 3/4
HOURS
PB FS
48K 44.1K 32K
MINUTES
REC MODE
2CH 4CH
SECONDS
FRAMES
-60
-60
S
VITC
REMOTE
CH-
1
3
CH-
2
4
9P i.LINK
EDIT MODE
Time code (when recording, the time code is
generated by the internal time code
generator; when playing back, the time code
is read from the tape.)
U-BIT
User bit data (when recording, the user bit
data is according to the most recent settings;
when playing back, the user bit data is read
from the tape.)
1
4,5,6
Note
When the REMOTE indicator in the front panel display
section is lit, the COUNTER SELECT button does not
operate while the tape is moving. In such cases, use the
external equipment connected to the REMOTE connector
on the rear panel to select the time data.
1 Press the COUNTER SELECT button to light the time
data type indicator “TC” or “U-BIT.”
TC: To set the initial time code value
U-BIT: To set user bit data
The current time code value or user bit data is shown
in the time counter display.
Setting the Time Data
51
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press the SET (YES) button.
shown below.
The message “NOW SAVING...” appears on the
monitor screen, “Saving...” appears in the time counter
display, and the new settings are stored in memory.
After this saving operation is completed, the monitor
screen and the time counter display return to their
usual status.
Menu item
TC MODE
RUN MODE
Setting
“INT PRESET”
“FREE RUN” or “REC RUN”
Normally “ON (DF)”
DF MODE
(for DSR-1500A only)
Note
The set data may be lost if you power off the unit while
the above saving operation is in progress. Wait until
the saving operation is completed before powering off.
3 Press the TC PRESET button in the menu control
section.
The current setting is shown on the monitor screen and
in the time counter display on the front panel. The
leftmost digit keeps flashing.
One of the following menu screens is displayed on the
monitor depending on the setting made in step 1.
Advancement of internal time code
generator
The internal time code generator can advance in either of
two modes, which can be set with the RUN MODE menu
TC PRESET MODE
TCG 00:00:00:00
UB PRESET MODE
UBG 00:00:00:00
FREE RUN: Advancement starts when the data saving
operation is completed.
REC RUN: Advancement starts when recording starts and
stops when recording stops.
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
To set the current time as the initial time
code value
DATA SAVE :
SET KEY
DATA SAVE :
SET KEY
ABORT : TC PRESET KEY
ABORT : TC PRESET KEY
In step 2 above, set the RUN MODE menu item to FREE
RUN, then set the current time (format: HH:MM:SS:FF =
hours: minutes:seconds:frame number) in step 3 and
subsequent steps.
Initial time code value setting
screen
User bit setting screen
Note
If you press the TC PRESET button while CNT value
is being displayed, the message “COUNTER MODE
IS SELECTED.” will appear on the monitor screen
and “CNT mode!” will appear in the time counter
display on the front panel. If this happens, press the
COUNTER SELECT button to light the time data type
indicator “TC” or “U-BIT.”
Synchronizing Internal and External
Time Codes
The internal time code generator can be synchronized with
an external time code (LTC) input to this unit.
To synchronize the internal time code to
external time code
Input an external time code (LTC) signal to the TC IN
connector, then set the TC MODE menu item (see page
68) to EXT REGEN.
The internal time code generator locks onto the external
time code and starts advancing. Once the internal time
code generator has been synchronized in this way, you can
disconnect the external time code input and this unit will
maintain the synchronized time code.
4 Use the gand Gbuttons to move the flashing digit to
the value to be changed.
5 Use the f and F buttons to change the value of the
flashing digit.
Enter hexadecimal values (0 to 9, A to F) when setting
user bit data.
6 Repeat steps 4 and 5 until you have set the desired
values for all digits.
Note
To set a value of 00:00:00:00, simply press the RESET
(NO) button.
When the selected input mode is “SDTI” or “i.LINK” (the
SDTI or i.LINK indicator is lit in the INPUT signal display
section), setting the TC MODE menu item to EXT
REGEN causes the internal time code generator to
Setting the Time Data
52
Download from Www.Somanuals.com. All Manuals Search And Download.
automatically synchronize with the external time code
input to the unit via the SDTI or i.LINK interface.
1 Press the MENU button in the menu control section.
SYSTEM MENU
Setup menu
SETUP MENU
Once an external time code signal has been input, the
internal time code advancement mode and frame count
mode are automatically set as follows:
AUTO FUNCTION
Time counter display
HOURS METER
Advancement mode: FREE RUN
Frame count mode: Same as external time code (drop
frame or non-drop frame)
To confirm external synchronization
Press the STOP button to put the unit into stop mode, then
press the REC button.
Monitor screen
Look at the time counter display and check that the time
code value displayed there matches the external time code
value.
2 Press the f or F button to select “AUTO
FUNCTION.”
Rerecording the Time Code—TC
Insert Function
SYSTEM MENU
Auto func
SETUP MENU
AUTO FUNCTION
Time counter display
HOURS METER
The TC insert function makes it possible to use the internal
time code generator to rewrite time code or user bits when
the time code recorded on a tape is discontinuous.
When recording in DVCAM format, you can start
recording time code from an initial value which can be set
Monitor screen
Notes
• Use a tape which is recorded in the DVCAM format.
(You cannot use the TC insert function with a tape
recorded in DV format.)
• The time code recording starts from the current tape
position. Cue the tape up beforehand to the required start
position.
3 Press the G button.
This displays the items in the level 1 of the auto mode
execution menu.
• If you use a tape on which ClipLink log data is recorded,
the ClipLink log data will be lost.
AUTO FUNCTION MENU
SDTI DUB
SDTI DUBBING
i.LINK DUBBING
Time counter display
Use the following procedure.
TC INSERT
MENU
RESET(NO)
1
2
TC
PRESET
SET(YES)
7,8
3,5
Monitor screen
2,4
Setting the Time Data
53
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press the F button to select “TC INSERT.”
7 Press the SET (YES) button.
Time code recording starts from the current tape
position.
AUTO FUNCTION MENU
TC insert
SDTI DUBBING
i.LINK DUBBING
Time counter display
TC INSERT
TC INSERT
Executing
Time counter display
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00
Monitor screen
ABORT:MENU KEY
Monitor screen
5 Press the G button.
The following message appears.
Note
If the recording format of the tape is not DVCAM, a
different message appears.
See “When the recording format of the tape is not
TC INSERT
Set tape!
Time counter display
INSERT THE TAPE IN
THIS VTR.
When the recording ends, the message “TC INSERT
COMPLETED. PUSH THE YES BUTTON.” appears
on the monitor screen and “Completed” appears in the
time counter display.
ABORT:MENU KEY
8 Press the SET (YES) button to exit the menu.
Monitor screen
When recording format is not DVCAM
When you carry out step 5 of the foregoing procedure, the
following message appears.
Note
If the recording format is not DVCAM, a different
message appears.
See “When recording format is not DVCAM” (page
54).
TC INSERT
Not DVCAM!
Time counter display
NO TC INSERT FUNCTION
AVAILABLE, DV RECORDING
FORMAT SELECTED.
SELECT DVCAM RECORDING
FORMAT.
6 Insert the cassette.
A message to confirm the TC insert operation appears.
PUSH THE YES BUTTON.
TC INSERT
TC insert?
Time counter display
Monitor screen
START TC INSERT?
Press the SET (YES) button to end the operation and do it
over again after setting the REC FORMAT menu item (see
page 65) to DVCAM. You can use the TC insert function
in DVCAM format only.
START:YES KEY
ABORT:MENU KEY
Monitor screen
When the recording format of the tape is not
DVCAM
When you carry out step 7 of the foregoing procedure, the
following message appears.
To cancel the TC insert operation
Press the MENU button.
Setting the Time Data
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TC INSERT
Not DVCAM!
Time counter display
TC INSERT IS ABORTED
DUE TO NON DVCAM
FORMAT SOURCE.
PUSH THE YES BUTTON.
Monitor screen
Press the SET (YES) button to end the operation and do it
over again after replacing the tape with one recorded in
DVCAM format.
Setting the Time Data
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
When controlling this unit from external equipment, set
LOCAL/REMOTE switch so that the remote mode
indicators in the display section are on or off as follows.
High-Speed and Low-
Speed Search—Quickly
and Accurately
Determining Editing
Points
• When using an editing control unit connected to the
REMOTE connector:
Switch/menu item
Setting
LOCAL/REMOTE switch
REMOTE
(REMOTE indicator lights.)
Use the search function to easily locate the desired scene
and to quickly and accurately determine edit points.
REMOTE I/F menu item
9PIN
(9P indicator lights.)
• When using a SIRCS-compatible remote control unit
connected to the CONTROL S connector:
When F. FWD/REW under the AUTO EE SELECT menu
can use the F FWD and REW buttons on this unit or
external equipment for high-speed search.
Switch/menu item
Setting
LOCAL
—
LOCAL/REMOTE switch
REMOTE I/F menu item
Search Operations via External
Equipment
• When using equipment connected to the i.DV IN/
OUT connector:
You can control the unit in the following operation modes
from an editing control unit (ES-7, PVE-500, etc.)
connected to the REMOTE connector on the rear panel, a
SIRCS-compatible remote control unit such as the DSRM-
10 connected to the CONTROL S connector (on the front
panel), or control equipment connected to the i.DV IN/
OUT connector.
Shuttle: Use this mode to view color video playback at
speeds ranging from 0 to 60 times normal speed in
both directions.
Switch/menu item
Setting
LOCAL/REMOTE switch
REMOTE
(REMOTE indicator lights.)
REMOTE I/F menu item
i.LINK
(i.LINK indicator lights.)
For description on how to carry out search operations via
external equipment, see the operating instructions for the
equipment.
Note
When controlling the unit from the DSRM-10 for
shuttle-mode search, the maximum search speed is 16
times normal speed in both directions.
Jog: Use this mode for low-speed search and frame-by-
frame search.
Digital slow: Use this mode for noise-free color video
1
playback at speeds ranging from 0 to / times normal
speed in both directions.
2
Still: Use this mode to view a still picture of any field.
Jog audio: Use this mode to monitor the audio at speeds
1
ranging from 1 to / times normal speed in both
directions.
30
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Connections for dubbing via i.LINK interface
To carry out dubbing through the i.LINK interface,
connect the i.DV IN/OUT connectors on this unit and the
player.
Digitally Dubbing Signals
in DVCAM/DV Format
Use the following procedure.
In addition to straightforward tape dubbing, you can also
use this unit to dub signals in DVCAM/DV format
automatically from the beginning of the tape to the end
through the SDTI (QSDI) or i.LINK interface.
• To use the SDTI (QSDI) interface, the optional DSBK-
1501 board is required.
When a tape recorded on a DSR-1/1P Digital
Videocassette Recorder or DSR-130/130P Digital
Camcorder is dubbed, the ClipLink log data held in the
cassette memory is also copied.
MENU
RESET(NO)
SET(YES)
1,9
2
TC
PRESET
7
3,4,5
Notes
• It is not possible to dub signals recorded in DV (LP)
format.
2,4
Digital dubbing is carried out in the digital format used
on the source tape regardless of the recording format
selected on this unit. If the source tape begins with a
section in which no signals are recorded, the
corresponding no-signal section created at the beginning
of the tape recorded on this unit may have a different
length depending on the digital format of the source tape,
the recording format selected on this unit, etc. During
dubbing, if the digital format of the source tape changes,
no signals are recorded until the initial digital format is
restored. No signals are recorded also when the digital
format used on the player is DV (LP).
1 Press the MENU button in the menu control section.
SYSTEM MENU
Setup menu
SETUP MENU
AUTO FUNCTION
Time counter display
HOURS METER
• Regardless of the audio recording mode setting of this
unit, dubbing is performed with the original audio
recording mode unchanged (two-channel/48 kHz mode
or four-channel/32 kHz mode).
• Approximately the last 2 minutes of the tape may not be
copied because of differences in tape lengths. (If an
index picture is recorded in this portion, it may also not
be copied.)
• A continuous recorded section of approximately 5
seconds is required before the recording start point. It is
recommended to record beforehand color bars or a
similar signal at the start point of the source tape to be
dubbed on this unit.
Monitor screen
2 Press the f or F button to select “AUTO
FUNCTION.”
SYSTEM MENU
Auto func
SETUP MENU
AUTO FUNCTION
Time counter display
Connections for dubbing via SDTI (QSDI)
interface
HOURS METER
To carry out dubbing through the SDTI (QSDI) interface,
connect the REMOTE and SDTI (QSDI) IN/OUT
connectors on this unit to those on the DSR-85/85P/70A/
70AP/2000/2000P/1800/1800P/1600/1600P/1500A/
1500AP.
Monitor screen
For details of the connections and switch settings, see
Digitally Dubbing Signals in DVCAM/DV Format
Download from Www.Somanuals.com. All Manuals Search And Download.
57
3 Press the G button.
6 Insert the source tape in the player, and the recording
tape in this unit.
This displays the items on level 1 of the auto mode
execution menu.
A message to confirm the dubbing operation appears.
AUTO FUNCTION MENU
SDTI DUB
SDTI DUBBING
SDTI DUBBING
Start dub?
(A/V/TC/CM)
i.LINK DUBBING
Time counter display
Time counter display
TC INSERT
START QSDI DUBBING?
START:YES KEY
ABORT:MENU KEY
Monitor screen
Monitor screen
4 Press the G button to display the menu level 2 for the
item “SDTI DUBBING,” and select the data to be
dubbed with the F button.
To cancel the dubbing operation
Press the MENU button.
7 Press the SET (YES) button.
The tape is automatically wound back to the
beginning, and dubbing starts.
Example: Selecting “A/V/TC/CM”
AUTO FUNCTION MENU
>A/V/TC/CM
SDTI DUBBING
A/V
Time counter display
SDTI DUBBING
Executing
(A/V/TC/CM)
A/V/TC
A/V/TC/CM
Time counter display
EXECUTING.
TCR 00:00:00:00
UBR 00:00:00:00
Monitor screen
ABORT:MENU KEY
Monitor screen
5 Press the G button.
The following message appears.
To end the dubbing operation while it is in progress
Press the STOP button.
SDTI DUBBING
Set tape!
(A/V/TC/CM)
When the dubbing is completed, message
“COMPLETED” appears on the monitor screen and
“Completed” in the time counter display.
The source tape and recording tape are both
automatically rewound to the beginning, and the
cassettes ejected. When the cassette is ejected, this unit
returns to the state in step 5.
Time counter display
INSERT RECORD TAPE IN
THIS VTR AND SOURCE
TAPE IN THE PLAYER VTR.
ABORT:MENU KEY
Note
If the recording format of the source tape is DV (LP),
different messages appear.
Monitor screen
See “When the recording format of the source tape is
8 To continue by dubbing another tape, repeat steps 6
and 7.
Digitally Dubbing Signals in DVCAM/DV Format
58
Download from Www.Somanuals.com. All Manuals Search And Download.
9 When the dubbing is completed, press the MENU
When the recording format of the source tape is
DV (LP)
button to exit the menu.
When you carry out step 7 of the foregoing procedure, the
following messages appear.
If the following message appears in step 6 for an
A/V/TC/CM dubbing operation
• When the player is not the DSR-2000/2000P
SDTI DUBBING
CM capacity!
Time counter display
During execution
(A/V/TC/CM)
SDTI DUBBING
(A/V/TC/CM)
CM MEMORY STORAGE
CAPACITY OF THE RECORD
TAPE IS TOO SMALL.
EXECUTING.
TCR 00:02.45.25
UBR 00:00.00.00
ABORT:MENU KEY
PLAYER VTR'S SERVO
UNLOCKED.
Monitor screen
ABORT:MENU KEY
When carrying out A/V/TC/CM dubbing, if you insert the
cassettes in step 6, the cassette memory capacity of the
cassettes inserted in both this unit and the player are
checked automatically.
If the cassette memory capacity of the source tape is larger
than that of the recording tape, the above message appears.
In this case, replace the recording tape by a tape with a
larger cassette memory capacity.
Monitor screen (Example display for DSR-1500A)
After execution
SDTI DUBBING
SV unlocked
Time counter display
(A/V/TC/CM)
DUBBING COMPLETED.
HOWEVER, PLAYER VTR'S
SERVO UNLOCKED
If the following message appears in step 7 for an
A/V/TC/CM dubbing operation
DURING DUBBING.
PUSH THE SET BUTTON.
SDTI DUBBING
Copy CM?
(A/V/TC/CM)
ABORT:MENU KEY
Time counter display
SDTI DUBBING IS ABORTED.
Monitor screen
EXECUTE CM COPY?
• When the player is the DSR-2000/2000P
During execution
COPY
:YES KEY
NOT COPY:NO KEY
SDTI DUBBING
(A/V/TC/CM)
Monitor screen
EXECUTING.
When carrying out A/V/TC/CM dubbing, if you press the
STOP button to stop dubbing in step 7, or if dubbing stops
because the source tape is longer than the recording tape,
the above message appears to confirm whether or not to
copy the contents of the cassette memory.
To copy the contents of the cassette memory, press the
SET (YES) button.
TCR 00:03.00.27
UBR 00:00.00.00
NON DVCAM/DV(SP) FORMAT
SOURCE.
ABORT:MENU KEY
Monitor screen (Example display for DSR-1500A)
If you do not wish to copy the contents of the cassette
memory, press the RESET (NO) button. If you press the
RESET (NO) button, however, the contents of the cassette
memory may not agree with the material recorded on the
tape.
Digitally Dubbing Signals in DVCAM/DV Format
Download from Www.Somanuals.com. All Manuals Search And Download.
59
After execution
SDTI DUBBING
No DVCAM/DV
(A/V/TC/CM)
Time counter display
DUBBING COMPLETED.
HOWEVER, A NON DVCAM/
DV(SP) FORMAT SEGMENT
WAS ON THE SOURCE TAPE.
PUSH THE SET BUTTON.
ABORT:MENU KEY
Monitor screen
In either case, the source tape section recorded in DV (LP)
format is dubbed as a no-signal section.
Digitally Dubbing Signals in DVCAM/DV Format
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings Chapter
4
Menu Organization
As shown in the following figure, the menu system
consists of four levels and is functionally divided into three
subsystems: the setup menu, the auto mode (AUTO
FUNCTION) execution menu and the digital hours meter
display menu.
This chapter mainly describes the setup menu, showing its
contents and how to operate it.
For details of the AUTO FUNCTION menu, see “Digitally
For details of the digital hours meter display, see “Regular
The items of the setup menu are divided into several
functional groups on level 1, and except for the MENU
GRADE item the settings themselves are made on level 2
or level 3.
Also, the menu items are divided into two categories
according to how frequently they are accessed: the “basic”
items, to which frequent access is normally required, and
the “enhanced” items, which are less frequently used. In
the following figure, the items shown in boldface are basic
items, and the other items are enhanced items.
The menu settings are saved in non-volatile memory,
which means they are not erased when you power off the
unit after executing the setting operation.
Menu Organization
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu organization
Menu selection level
Level 1
Level 2
Level 3
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
REPEAT FUNCTION
SETUP MENU
OPERATIONAL FUNCTION
B PRESET
CASSETTE OUT
F. FWD/REW
STOP
AUTO EE SELECT
LOCAL ENABLE
REC FORMAT
REC INHIBIT
STANDBY OFF
SEARCH ENABLE
MAX SRCH SPEED
PREROLL TIME
AFTER CUE-UP
PLAY START
SHUTTLE
F. FWD/REW
AUTO REW
A MODE CHANGE
CHARA. DISPLAY
CHARA. POSITION
CHARA. TYPE
CHARA. VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
DISPLAY CONTROL
OVER DISP HOLD
BRIGHTNESS
ALARM
REF ALARM
TC MODE
TIME CODE
RUN MODE
a)
DF MODE
TC SELECT
VITC
TCG REGEN
UB BINARY GP.
VITC POS SEL-1
VITC POS SEL-2
VITC OUTPUT
EE OUT PHASE
MUTE IN SRCH
TAPE PROTECTION
FROM STOP
FROM STILL
STOP TIMER
STILL TIMER
NEXT MODE
(Continued)
a) Menu item for DSR-1500A only
Menu Organization
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu selection level
Level 1
Level 2
Level 3
(Continued)
INT VIDEO SG
VIDEO CONTROL
STD/NON-STD
OUT REF SEL
SETUP REMOVE
a)
a)
SETUP ADD
CC(F1) BLANK
a)
a)
CC(F2) BLANK
WIDE MODE
ESR MODE
PROCESS CONTROL
C PHASE MODE
ADJ RANGE
VIDEO GAIN
CHROMA GAIN
CHROMA PHASE
a)
b)
SETUP LEVEL
BLACK LEVEL
b)
LINE 335
INPUT BLANK
AUDIO CONTROL
REC MODE
INPUT ARRANGE
LEVEL SELECT
INT AUDIO SG
JOG CONTROL
SHUTTLE MUTE
AUDIO EDIT
REF LEVEL
CH1 IN LEVEL
CH2 IN LEVEL
OUTPUT LEVEL
DV PB ATT
INTERFACE SELECT
VIDEO OUTPUT
DIGITAL OUTPUT
AUDIO OUTPUT
REMOTE I/F
SETUP BANK OPERATION
RECALL BANK1
RECALL BANK2
RECALL BANK3
RECALL BANK4
SAVE BANK 1
SAVE BANK 2
SAVE BANK 3
SAVE BANK 4
MENU GRADE
SDTI DUBBING
A/V
AUTO FUNCTION
A/V/TC
A/V/TC/CM
A/V
i.LINK DUBBING
TC INSERT
A/V/TC
A/V/TC/CM
T1:OPERATION
HOURS METER
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
a) Menu item for DSR-1500A only
b) Menu item for DSR-1500AP only
Menu Organization
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Contents
Examples:
Setup Menu
Indication on monitor
screen
Indication in time counter
display
The purpose and settings of the setup menu items are
described below.
OPERATIONAL FUNCTION [Operational]
CASSETTE OUT
[>> Cass. out]
[>>> EE]
Indications of menu items and settings
*EE
• In the table below entitled “Menu contents,” the
indication of each menu item or setting on the monitor
screen is shown first, then the indication of the same item
or setting in the time counter display of this unit is shown
in square brackets ([ ]).
• Settings preceded by an asterisk (such as *EE) are
factory default settings.
• In the time counter display, one to three “>” symbols
may precede itemor setting indications depending on the
current menu level. Larger numbers of “>” symbols
indicate lower menu levels.
Menu contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
REPEAT FUNCTION [> REP
FUNC]: Make settings for
repeat playback mode.
REPEAT MODE [>>
REPEAT MD]:
*OFF [>>> OFF]: Do not put the unit into repeat playback
mode.
Determine whether or ON [>>> ON]: Put the unit into repeat playback mode.
not to put the unit into ON (FREEZE) [>>> FREEZE]: Put the unit into freeze
repeat playback mode.
playback mode. In this case, while the unit is cueing up to
the repeat start point, the freeze picture of the repeat end
point is displayed.
REPEAT TOP [>> REP
TOP]: Determine
whether the repeat
start point is the
beginning of tape or
point A.
*TAPE TOP [>>> Tape top]: The repeat start point is the
beginning of tape.
A POINT [>>> A point]: The repeat start point is point A as
set by the user.
REPEAT END [>> REP
*VIDEO END [>>> VD end]: The repeat end point is the end
END]: Determine
of the video recorded portion.
whether the repeat end TAPE END [>>> Tape end]: The repeat end point is the end
point is the end of the
of tape.
video recorded portion, B POINT [>>> B point]: The repeat end point is point B as set
the end of tape or point
B.
by the user.
Specify a time code
value to be used as the
setting of point A.
Specify a time code
value to be used as the
setting of point B.
Menu Contents
64
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
AUTO EE SELECT [> Auto EE]: CASSETTE OUT [>>
*EE [>>> EE]: Output video and audio signals received from
Determine whether the unit
enters EE mode or PB mode
when audio and video
signals from other equipment
are input.
When this unit is used as the
recorder for cut editing, it is
possible to output the input
audio and video signals to
the monitor. This enables
editing operation to be
carried out using a single
monitor.
Cass. out]: Operations
other equipment.
when the cassette has PB [>>> PB]: Mute video and audio signals.
been ejected
F. FWD/REW [>> F. FWD/ EE [>>> EE]: Output video and audio signals received from
REW]: Operations
other equipment.
when in fast forward or *PB [>>> PB]: The unit enters playback mode and outputs a
rewind mode
playback video signal. Audio signals are muted.
STOP [>> STOP]:
Operations when in
stop mode
EE [>>> EE]: Output video and audio signals received from
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
STANDBY OFF [>> STBY EE [>>> EE]: Output video and audio signals received from
OFF]: Operations
when in standby off
mode
other equipment.
*PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
LOCAL ENABLE [> Local ENA]: Select which of the tape
transport control buttons (EJECT, REW, PLAY, F FWD,
STOP, and REC) operate when the LOCAL/REMOTE
switch is set to “REMOTE.”
ALL DISABLE [>> All DIS]: All of the tape transport control
buttons are disabled.
*STOP & EJECT [>> STOP&EJ]: Only the STOP and EJECT
buttons are enabled.
ALL ENABLE [>> All ENA]: All of the tape transport control
buttons are enabled, and settings such as preroll time
change or time data display selection are effective.
REC FORMAT [> REC FMT]: Select the recording format.
*DVCAM [>> DVCAM]: DVCAM format
DV (SP) [>> DV (SP)]: DV (SP) format
REC INHIBIT [> REC INH]: Determine whether to prohibit
*OFF [>> OFF]: Do not prohibit recording on tape.
ON [>> ON]: Prohibit recording on tape. (The REC INHI
indicator in the display section lights.)
recording on tape.
SEARCH ENABLE [> Search ENA]: Select whether to enable *DISABLE [>> DISABLE]: Do not enable.
playback in shuttle/jog mode by the use of the arrow
(fFgG) buttons.
ENABLE [>> ENABLE]: Enable.
MAX SRCH SPEED [> Max
SRCH]: Specify the
SHUTTLE [>> SHUTTLE]: X60 [>>> X60]: Maximum 60 times normal speed
Specify the maximum *X32 [>>> X32]: Maximum 32 times normal speed
maximum tape speed in
search (shuttle) mode and F.
FWD (fast forward)/REW
(rewind) mode.
tape speed in search
(shuttle) mode.
X16 [>>> X16]: Maximum 16 times normal speed
F. FWD/REW [>> F. FWD/ MAX [>>> MAX]: No maximum tape speed is specified.
REW]: Specify the
*X85 [>>> X85]: Maximum 85 times normal speed
maximum tape speed X60 [>>> X60]: Maximum 60 times normal speed
in F. FWD/REW mode. X32 [>>> X32]: Maximum 32 times normal speed
Note
When this item is set to MAX, the playback video signal is
muted.
PREROLL TIME [> Preroll]: Set the preroll time.
15 SEC [>> 15 sec] to 0 SEC [>> 0 sec]: The preroll time can
be set in one-second increments to between 0 and 15
seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
following cue-up.
Menu Contents
65
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
PLAY START [> PLAY start]: Set the timing for switching from 16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY [>> 4
stop mode to playback mode.
delay]: The larger the numerical value, the longer the
In an editing system including an editing control unit such as
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
delay.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-1500A) or 4 FRAME DELAY [>> 4 delay] (for DSR-
1500AP)
AUTO REW [> Auto REW]: Select whether to rewind the tape DISABLE [>> DISABLE]: Do not rewind the tape
automatically when recording or playback reaches the end
of a tape.
automatically.
*ENABLE [>> ENABLE]: Rewind the tape automatically.
A MODE CHANGE [> Aud change]: Determine whether or
*OFF [>> OFF]: Do not permit.
not to permit audio insert editing that uses a different audio ON [>> ON]: Permit.
recording mode (2- or 4-channel mode) from that which
was used for the tape loaded in the recorder.
Note
This is used when entirely changing the recording audio mode.
At the IN and OUT points, audio recording is muted.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not OFF [>> OFF]: Do not output text. (In spite of this setting,
to output text (such as time code values) from the B−Y/
CPST (SUPER) connector.
pressing the MENU button causes menu text to be
output.)
*ON [>> ON]: Output text.
CHARA. POSITION [> Chara pos]: Set the position of text
superimposed on output from the B−Y/CPST (SUPER)
connector to the monitor.
Use the fFgG buttons in the menu control section to adjust
the text position while watching the monitor screen.
To return to level 1 of the setup menu, press the MENU button.
CHARA. TYPE [> Chara type]: Set the type of characters in
text superimposed on output from the B−Y/CPST
(SUPER) connector to the monitor.
Make the following settings while watching the monitor screen.
*WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
CHARA. VSIZE [> Chara size]: Determine the vertical size of Make the selection while watching the monitor screen.
characters such as time code output from the B−Y/CPST *X1 [>> X1]: Standard size
(SUPER) connector for superimposed display on the
monitor.
X2 [>> X2]: 2 times standard size
DISPLAY INFO [> DISP info]: Select information
superimposed on output from the B−Y/CPST (SUPER)
connector to the monitor.
*TIME DATA & STATUS [>> Time&STA]: Time data and
operating mode indications
TIME DATA & UB [>> Time&UB]: Time data selected using
the COUNTER SELECT button, and user bit data (When
user bit data is selected using the COUNTER SELECT
button, user bit data and time code are shown.)
TIME DATA & CNT [>> Time&CNT]: Time data selected
using the COUNTER SELECT button, and CNT value
(When CNT is selected using the COUNTER SELECT
button, CNT value and time code are shown.)
TIME DATA & TIME[>> Time&Time]: Time data and VITC
TIME DATA ONLY [>> Time]: Time data only
REC DATE & TIME [>> REC Date]: The time data selected
with the COUNTER SELECT button is shown in the time
counter display, and the date and time of recording are
shown on the monitor screen.
Menu Contents
66
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
SUB STATUS [> Sub status]: Select supplementary status
*OFF [>> OFF]: Nothing of supplementary status information
information superimposed on output from the B−Y/CPST EDIT PRESET [>> Edit pre]: Indications of the editing mode
(SUPER) connector to the monitor.
settings made from the connected editing control unit
TC MODE [>> TC mode]: Indications of the operating mode
of internal time code generator
REMAIN [>> Remain]: Remaining capacity of the tape
AUDIO MIXING [>> Aud Mix]: Indications of input audio
mixing
ALL [>> ALL]: All of the above-mentioned items of
supplementary status information
For details of supplementary status information displayed on
the monitor when a setting other than OFF is selected, see
MENU DISPLAY [> Menu DISP]: Set the type of characters in Make the following settings while watching the monitor screen.
menu text superimposed on output from the B−Y/CPST
(SUPER) connector to the monitor.
*WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
PEAK HOLD [> Peak hold]: Set the peak hold time for the
1.5 SEC [1.5 sec] to OFF [>> OFF]: Set the peak hold time in
the range of OFF (no peak hold) to 1.5 seconds in 0.1
second steps.
audio level meters.
Factory default setting: OFF [>> OFF]
OVER DISP HOLD [> Hold OVER]: Determine whether or not *OFF [>> OFF]: Do not hold the OVER indication display.
to hold the OVER indication display on the audio level
meters once the indications light.
ON (HOLD) [>> ON]: Hold the OVER indication display.
Note
With ON selected, once the display is held it will remain held
unless you change the setting to OFF.
BRIGHTNESS [> Brightness]: Set the brightness of front
Set brightness as a percentage of the maximum.
100 % [>> 100%]
panel indicators.
*75 % [>> 75%]
50 % [>> 50%]
ALARM [> ALARM]: Determine whether alarm messages are OFF [>> OFF]: Alarm messages are not issued.
issued or not.
*ON [>> ON]: Alarm messages are issued.
REF ALARM [> REF ALARM]: Determine whether alarm
OFF [>> OFF]: Alarm messages are not issued.
messages related to reference video signal are issued or *ON (LIMITED) [>> ON (Limit)]: Alarm messages are issued
not.
only during recording mode, EE mode, REC-pause mode,
and edit mode.
ON [>> ON]: Alarm messages are issued.
Menu Contents
67
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
TC MODE [> TC mode]: Determine the time code to use:
*INT PRESET [>> PRESET]: Use internal time code with a
preset initial value.
internal time code using a preset initial value, regenerated
internal time code (locked to time code read from tape), or INT REGEN [>> REGEN]: Use internal time code locked to
external time code.
time code read from tape.
EXT REGEN [>> EXT]: Use external time code selected as
follows.
• When TC is selected
External time code input to the TC IN connector
• When VITC is selected
The VITC time code present in the input video signal
Note
When the selected input mode is SDTI or i.LINK (the V:SDTI,
SDTI, or i.LINK indicator is lit in the INPUT signal display
section), setting this item to EXT REGEN causes the internal
time code generator to automatically synchronize with the
external time code input to the unit via the SDTI or i.LINK
interface.
RUN MODE [> RUN mode]: Select the advancement (RUN)
*FREE RUN [>> FREE RUN]: Time code generator keeps
mode of the time code generator.
running.
REC RUN [>> REC RUN]: Time code generator only runs
while recording.
Note
Set to FREE RUN when carrying out editing with an editing
control unit. With the REC RUN setting, editing will not be
carried out correctly.
(For DSR-1500A only)
*ON (DF) [>> ON (DF)]: Drop frame mode
OFF (NDF) [>> OFF (NDF)]: Non-drop frame mode
DF MODE [> DF mode]: Select whether the time code
generator and time counter operate in drop frame mode or
non-drop frame mode.
Normally select drop frame mode to keep in
synchronization with real time. The non-drop frame mode
is useful for example when using computer graphics, and
working on a frame count basis.
TC SELECT [> TC select]: Determine which to display in the VITC [>> VITC]: Display VITC.
time counter display, TC or VITC.
*TC [>> TC]: Display TC.
VITC [> VITC]: Determine whether to record the internally
OFF [>> OFF]: Do not record the internally generated time
code as VITC. (VITC present in the input video signal is
recorded unchanged.)
generated time code as VITC.
*ON [>> ON]: Record the internally generated time code as
VITC.
TCG REGEN [> TCG regen]: Select the signal to be
*TC & UB [>> TC & UB]: Both the time code and user bits are
regenerated when the time code generator is in the
regenerated.
regeneration mode (i.e., when the TC MODE menu item is TC [>> TC]: Only the time code is regenerated.
set to INT REGEN or EXT REGEN).
UB [>> UB]: Only the user bits are regenerated.
UB BINARY GP. [> Binary Gp.]: Select the user bit binary
*000: NOT SPECIFIED [>> 000]: Character set not specified
001: ISO CHARACTER [>> 001]: 8-bit characters conforming
to ISO 646 and ISO 2022
group flag of the time code generator.
010: UNASSIGNED-1 [>> 010]: Undefined
011: UNASSIGNED-2 [>> 011]: Undefined
100: UNASSIGNED-3 [>> 100]: Undefined
101: PAGE/LINE [>> 101]: Multiplex
110: UNASSIGNED-4 [>> 110]: Undefined
111: UNASSIGNED-5 [>> 111]: Undefined
Note
When the TC MODE menu item is set to EXT REGEN, the
user-bit binary group flag setting follows the setting on the time
code input to this unit.
Menu Contents
68
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the
(For DSR-1500A)
VITC in.
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
from 12 to 20.
Factory default setting: 16 LINE [>> 16 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-2.
(For DSR-1500AP)
22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
from 9 to 22.
Factory default setting: 19 LINE [>> 19 line]
VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the
(For DSR-1500A)
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
from 12 to 20.
VITC in.
Factory default setting: 18 LINE [>> 18 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-1.
(For DSR-1500AP)
22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
from 9 to 22.
Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [> VITC out]: Select the time code to be output OFF [>> OFF]: Do not output VITC.
as VITC.
TC [>> TC]: Output TC after converting it into VITC.
*VITC [>> VITC]: Output VITC.
EE OUT PHASE [> EE out]: Determine the output phase for
the LTC signal output from the TC OUT connector when
recording time code and in STOP REC mode (forced EE
mode).
*MUTE [>> mute]: Mute the output.
THROUGH [>> through]: Output the time code input to the
TC IN connector as it is. (See example configuration on
VIDEO INPUT PHASE [>> V input]: Output the time code
with the same phase as the input video signal phase.
VIDEO OUTPUT PHASE [>> V output]: Output the time code
with the same phase as the output video signal phase.
MUTE IN SRCH [> Mute in SR]: Select whether to mute the
OFF [>> OFF]: Do not mute.
output from the TC OUT connector in search (jog/shuttle) *ON [>> ON]: Mute.
mode.
TAPE PROTECTION [Tape protct]: Settings related to tape Description of settings
and video head protection
FROM STOP [> From STOP]:
Set the time to switch from
stop mode to tape protection
mode.
STOP TIMER [>> STP
timer]: Set the time to
switch from stop mode
to tape protection
mode.
0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1 MIN [>>> 1 min]
FROM STILL [> From STILL]:
Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.
STILL TIMER [>> STL
timer]: Set the time to
switch from still search
mode to tape
0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1 MIN [>>> 1 min]
protection mode.
1
NEXT MODE [>> Next
mode]: Select the type
of tape protection
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.
*STEP FWD [>>> Step]: The tape is advanced at / times
30
normal speed for about 2 seconds.
STANDBY OFF [>>> STANDBY]: Standby off mode
Menu Contents
69
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
INT VIDEO SG [> Video SG]: Select the test signal to be (For DSR-1500A)
output from the internal test signal generator. When SG is *75% COLOR BARS [>> 75% bars]: 75% color bar signal
selected using the VIDEO button in the video/audio input BLACK BURST [>> BB]: Black burst signal
setting section, the internal test signal generator outputs
the selected test signal. This signal can be recorded.
*100% COLOR BARS [>> 100% bars]: 100% color bar signal
(For DSR-1500AP)
75% COLOR BARS [>> 75% bars]: 75% color bar signal
BLACK BURST [>> BB]: Black burst signal
STD/NON-STD [> STD/N-STD]: Select the STD or NON-STD *FORCED STD [>> STD]: The STD mode is always used
mode in accordance with the composite video or S-video
input.
(forced STD mode).
FORCED NON-STD [>> NON-STD]: Use this setting when
the input video signal is unstable (forced NON-STD
mode).
OUT REF SEL [> Out Ref]: Select the reference video signal *REF VIDEO [>> REF]: Use the signal input to a REF. VIDEO
to use.
IN connector as the reference video signal. The input
video signal to be edited is required to be in
synchronization with the reference video signal.
INPUT VIDEO [>> INPUT]: Use the input video signal
selected with the VIDEO button in the video/audio input
setting section.
(For DSR-1500A only)
*OFF [>> OFF]: Do not remove black setup.
SETUP REMOVE [> Setup rmv]: Determine whether or not to ON (REMOVE) [>> ON]: Remove black setup.
remove black setup (7.5 IRE) from input analog video
signals when converting them into digital signals.
(For DSR-1500A only)
*OFF [>> OFF]: Do not add black setup.
SETUP ADD [> Setup add]: Determine whether or not to add ON (ADD) [>> ON]: Add black setup.
black setup to analog video output signals.
(For DSR-1500A only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F1) BLANK [> CC1 blank]: Select whether to mute the
closed caption signal to be superimposed on the 1st field
of the output video signal.
(For DSR-1500A only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F2) BLANK [> CC2 blank]: Select whether to mute the
closed caption signal to be superimposed on the 2nd field
of the output video signal.
WIDE MODE [> Wide mode]: Determine whether to retain
wide-screen aspect ratio information accompanying video
being recorded or played back.
*AUTO [>> Auto]: When video being recorded or played back
is accompanied by wide-screen aspect ratio information,
retain the information.
OFF [>> OFF]: Ignore wide-screen aspect ratio information.
ON [>> ON]: Whenever recording or playing back video, retain
wide-screen aspect ratio information.
ESR MODE [> ESR mode]: Select whether to enable the edge *OFF [>> OFF]: Do not enable.
subcarrier reducer (ESR).
ON [>> ON]: Enable.
When playing back a composite signal, set this to ON.
Menu Contents
70
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
PROCESS CONTROL [> Proc
ctrl]
C PHASE MODE [>> C
Phas MD]: Select the
phase rotation mode
for chroma phase
*U/V (COMPOSITE) [>>> Cmpst]: Select this setting when
observing the composite video output level using a
composite vectorscope.
PB/PR (COMPONENT) [>>> Cmpnt]: Select this setting
when observing the component video output level using a
component vectorscope.
control.
The effect of this setting
applies to the output levels
of all of the composite
video, S-video, SDI and
component video signals.
ADJ RANGE [>> Adj
range]: Select the
variable range of the
VIDEO and CHROMA
gains.
*–3 to +3 (dB) [>>> –3/+3]: −3 dB to +3 dB
WIDE [>>> wide]: −∞ to +3 dB
VIDEO GAIN [>> V gain]: 000 [>>> 000] to 3FF [>>> 3FF]
Adjust the video output Factory default setting: 200H
level.
CHROMA GAIN [>> C
gain]: Adjust the
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: 200H
chroma output level.
CHROMA PHASE [>> C
phase]: Adjust the
chroma phase.
00 [>>> 00] to FF [>>> FF]
Factory default setting: 80H
(For DSR-1500A only)
SETUP LEVEL [>> Setup Factory default setting: 200H
000 [>>>000] to 3FF [>>> 3FF]
lev]: Adjust the black
setup level.
(For DSR-1500AP only)
BLACK LEVEL [>> Black Factory default setting: 200H
000 [>>> 000] to 3FF [>>> 3FF]
lev]: Adjust the black
level.
(For DSR-1500AP only)
INPUT BLANK [> Input blnk]
LINE 335 [>> Line 335]:
Switch blanking on or
off for the 335th line of
the input video signal.
BLANK [>>> blank]: Blank.
THROUGH [>>> through]: Do not blank.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
REC MODE [> REC mode]: Select the audio recording mode. *2 CHANNEL (48kHz) [>> 2 ch]: 2-channel, 48-kHz mode
4 CHANNEL (32kHz) [>> 4 ch]: 4-channel, 32-kHz mode
Menu Contents
71
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
INPUT ARRANGE [> Input arng]: Make settings for input
Set the channels on which to record the input audio signals as
follows.
audio mixing.
(1) Use the fFgG buttons to move the cursor and the SET
(YES) button to toggle the setting on and off.
(2) To save the settings, press the MENU button to return to
the previous screen, then press the SET (YES) button.
Note
When, in 4-channel mode, analog audio is selected for all four
channels (channels 1/2 and 3/4), the same analog audio
signals are recorded on channels 1 and 3 and on channels 2
and 4, respectively. That is, the analog signal recorded on
channel 1 is also recorded on channel 3 and the analog signal
recorded on channel 2 is also recorded on channel 4.
You can adjust the audio level on each of the four channels
separately using the REC/PB LEVEL control knobs with the
VAR switch set to REC.
Example settings:
AUDIO INPUT SOURCE
ARRANGE
1
in1 in2 in3 in4
2
ch1:*on
ch2:
ch3:
ch4
on
on
on
on
3
4
ON/OFF : SET KEY
TO MENU : MENU KEY
A Input audio channel 1 (“in1”) is recorded on audio channel 1
(“ch1”) on tape.
B Input audio channels 2 and 4 (“in2” and “in4”) are recorded
mixed on audio channel 2 (“ch2”) on tape.
C Input audio channel 4 (“in4”) is recorded on audio channel 3
(“ch3”) on tape.
D Input audio channel 3 (“in3”) is recorded on audio channel 4
(“ch4”) on tape.
LEVEL SELECT [> Level Sel]
REF LEVEL [>> REF
Level]: Select the
audio reference level
(headroom) for
*–20 dB [>>> –20dB] (factory default setting for DSR-1500A)
*–18 dB [>>> –18dB] (factory default setting for DSR-
1500AP)
–16 dB [>>> –16dB]
–12 dB [>>>–12dB]
recording on tape.
Note
This setting is valid in DVCAM format only. When the
recording format is DV (SP), the reference level is fixed at −12
dB.
CH1 IN LEVEL [>> CH1
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
–3 dBm [>>> –3dBm] (for DSR-1500AP only)
according to the audio –6 dBm [>>> –6dBm]
level of the signal input
to the AUDIO IN 1/3
connector.
CH2 IN LEVEL [>> CH2
input]: Select the
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
audio level setting
–3 dBm [>>> –3dBm] (for DSR-1500AP only)
according to the audio –6 dBm [>>> –6dBm]
level of the signal input
to the AUDIO IN 2/4
connector.
OUTPUT LEVEL [>> Out
Level]: Select the
analog audio output
reference level.
*+4 dB [>>> +4dB]
0 dB [>>> 0dB]
–3 dB [>>> –3dB] (for DSR-1500AP only)
–6 dB [>>> –6dB]
INT AUDIO SG [> Audio SG]: Select the operation of the
SILENCE [>> silence]: Silent signal
internal audio test signal generator.
*1kHz SINE [>> 1kHz]: 1-kHz, −20 dB FS (for DSR-1500A) or
−18 dB FS (for DSR-1500AP) sine wave signal
When you select SG (audio test signal) as the audio input in
the video/audio input setting section on the front panel, the
audio test signal generated by the internal audio test signal
generator is input.
Menu Contents
72
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
JOG CONTROL [> Jog ctrl]: Select whether to adjust the
OFF [>> OFF]: Do not adjust the audio playback speed.
*ON [>> ON]: Adjust the audio playback speed.
audio playback speed during slow playback.
SHUTTLE MUTE [> Shutl mute]: Set the audio muting
*OFF [>> OFF]: Not muted.
CUEUP or PREROLL [>> CUEUP]: Muted during cue-up or
preroll operations.
conditions during shuttle playback.
FULL [>> FULL]: Muted in shuttle mode.
AUDIO EDIT [> Audio edit]: Specify the type of editing for
*CUT EDIT [>> Cut edit]: Cut editing (Discontinuity in audio
signal may result at the editing point, causing noise during
playback.)
audio signals.
FADE IN/OUT [>> Fade]: Fade in and fade out
IN
OUT
DV PB ATT [> DV PB ATT]: When playing back a tape
recorded in consumer DV format, select whether to
attenuate the audio output level.
OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.
Note
This setting is valid only when the recording format setting is
DVCAM. This is not valid for DV format.
INTERFACE SELECT [Interface]: Settings related to
external interfaces
Description of settings
VIDEO OUTPUT [> Video Out]: Select the format of analog
video signals to be output from the three VIDEO OUT
connectors (Y/CPST, R−Y/C/CPST, and B−Y/CPST
(SUPER)).
*COMPOSITE [>> Composite]: Composite video signals
S-VIDEO [>> S-Video]: S-video (separated Y and C) and
composite video signals
Y–R, B [>> Y–R, B]: Y, R−Y and B−Y component video
signals
Note
When this menu item is set to Y−R, B, the B−Y/CPST (SUPER)
connector outputs the B−Y signal. In this case, changing the
setting of an internal switch allows the text data for
superimposition on the monitor screen to be output from the
right-hand REF. VIDEO IN connector (marked
information about this, consult your Sony dealer.
). For more
DIGITAL OUTPUT [> Digit Out]: Select the format of signals *SDI [>> SDI]: SDI format
to be output from the SDI/SDTI (QSDI) OUT1/OUT2
connectors (optional DSBK-1501 board required).
SDTI [>> SDTI]: SDTI (QSDI) format
AUDIO OUTPUT [> Audio Out]: Select the channels for audio *1/2 CH [>> 1/2CH]: Output channel 1 to the AUDIO OUT 1/3
output from the AUDIO OUT 1/3 and 2/4 connectors.
connector and channel 2 to the AUDIO OUT 2/4
connector.
3/4 CH [>> 3/4CH]: Output channel 3 to the AUDIO OUT 1/3
connector and channel 4 to the AUDIO OUT 2/4
connector.
REMOTE I/F [> Remote I/F]: When remote-controlling this unit *9PIN [>> 9PIN]: Remote-control via the REMOTE connector.
with the LOCAL/REMOTE switch set to REMOTE, select
either the REMOTE connector or i.DV IN/OUT connector
(optional DSBK-1501 board required) for connecting a
remote control unit.
i.LINK [>> i.LINK]: Remote-control via the i.DV IN/OUT
connector.
Menu Contents
73
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP BANK OPERATION [Setup Bank]: Settings related Description of settings
to menu bank operations
RECALL BANK1 [> Recall 1]: Recall menu settings from
(1) Select the bank you want to recall, then press the G
menu bank 1.
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [> Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [> Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [> Recall 4]: Recall menu settings from
menu bank 4.
SAVE BANK 1 [> Save 1]: Save current menu settings to
(1) Select the bank you want to save, then press the G
button.
menu bank 1.
Message “SAVE OK?” appears.
(2) To save, press the SET (YES) button.
To quit saving, press the RESET (NO) button.
SAVE BANK 2 [> Save 2]: Save current menu settings to
menu bank 2.
SAVE BANK 3 [> Save 3]: Save current menu settings to
menu bank 3.
SAVE BANK 4 [> Save 4]: Save current menu settings to
menu bank 4.
Menu banks
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered 1 to 4.
Saved sets of menu settings can be recalled for use as required.
MENU GRADE [Menu grade]: Selection of menu items to
be displayed
Description of settings
Determine whether to display basic items only or both basic
and enhanced items on the monitor screen and in the time
counter display when using the menu.
*BASIC [> Basic]: Display basic items only.
ENHANCED [> Enhanced]: Display both basic and enhanced
items.
Menu Contents
74
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT PHASE mode
The time code output signal is synchronized with the input
video signal.
This mode is appropriate when the output from a single
device is recorded on a number of VCRs. The connections
are loop-through connections.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
EE OUT PHASE settings for time code
output
Use the following as reference information when setting
THROUGH mode
In this mode, the LTC signal is output with the phase
synchronized with the input time code signal. This mode is
appropriate when recording signals from multiple devices
on a number of VCRs.
Note
input signal formats to be used are required.
When the camcorder is in genlock mode, the time code
precision is 0 frames. When the camcorder is not in
genlock mode, it is 1 frame.
VIDEO OUT
VIDEO IN
Note
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
input signal formats to be used are required.
DSR-1500A/1500AP (1st unit)
Output device
(VCR, camera, etc.)
VIDEO IN
AUDIO IN
VIDEO IN
TIME CODE IN
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
Camcorder 1
TIME CODE OUT
DSR-1500A/1500AP (1st unit)
DSR-1500A/1500AP (2nd unit)
VIDEO IN
AUDIO IN
TIME CODE IN
TIME CODE OUT
Camcorder 2
DSR-1500A/1500AP (2nd unit)
VIDEO IN
VIDEO LOOP THRU
TIME CODE IN
TIME CODE OUT
DSR-1500A/1500AP (nth unit)
VIDEO IN
AUDIO IN
Composite video or SDI (video and audio) signal
Time code signal
TIME CODE IN
TIME CODE OUT
Camcorder n
DSR-1500A/1500AP (nth unit)
Composite video or S-video signal
Audio signal
Time code signal
Menu Contents
75
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO OUTPUT PHASE mode
The time code output signal is synchronized with the
output video signal.
This mode is appropriate when outputting signals from a
single device to a number of VCRs using separate cables
for video, audio, and time code.
In this mode, the same time code is recorded on all of the
VCRs 1 to n.
Note
input signal formats to be used are required.
VIDEO OUT
AUDIO OUT
VIDEO IN
VIDEO OUT
AUDIO IN
TIME CODE OUT
AUDIO OUT
TIME CODE IN
TIME CODE OUT
Output device
(VCR, camera, etc.)
DSR-1500A/1500AP (1st unit)
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1500A/1500AP (2nd unit)
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
TIME CODE IN
TIME CODE OUT
DSR-1500A/1500AP (nth unit)
• Composite video signal
• S-video signal
• Analog component signal
• SDI (video and audio) signal
Audio signal
Time code signal
Menu Contents
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Mode (AUTO FUNCTION) Execution Menu
The following table shows the purpose and function of the
items in the auto mode execution menu.
For details of the use of individual items, see “Digitally
Menu contents
SDTI DUBBING [SDTI DUB]: Selection of data for SDTI
dubbing
Settings
For dubbing through the SDTI (QSDI) interface, select data that A/V [> A/V]: Dub the audio and video.
the dubbing applies to.
A/V/TC [> A/V/TC]: Dub the audio, video, and time code.
A/V/TC/CM [> A/V/TC/CM]: Dub the audio, video, time code,
and cassette memory contents.
Note
When A/V is selected, the time code recorded follows the
setup menu.
i.LINK DUBBING [i.LINK DUB]: Selection of data for i.LINK Settings
dubbing
For dubbing through the i.LINK interface, select data that the
dubbing applies to.
A/V [> A/V]: Dub the audio and video.
A/V/TC [> A/V/TC]: Dub the audio, video, and time code.
A/V/TC/CM [> A/V/TC/CM]: Dub the audio, video, time code,
and cassette memory contents.
Note
When A/V is selected, the time code recorded follows the
setup menu.
TC INSERT [TC insert]: Time code rewriting
Settings
Note
Rewrite the time code from an initial value which can be set
freely.
Rewriting is possible only when the recording format is
DVCAM.
Menu Contents
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Basic
Items
Changing Menu Settings
The factory default setting is to display only the basic
items. To change the settings of basic items proceed as
follows.
This section explains how to change menu settings.
Buttons Used to Change Settings
Use the following buttons in the menu control section to
change the menu settings.
MENU
RESET(NO)
SET(YES)
1
TC
PRESET
Menu control buttons
Functions
MENU button
• Opens the menu and
launches menu control
mode.
• Closes the menu and exits
menu control mode.
9
3,5,7
2,4,6
8
f and F buttons
These buttons move the
highlighted cursor up and
down within the current level
to select an item or setting.
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
1 Press the MENU button in the menu control section.
g and G buttons
• Press the G button to go
down one level.
• Press the g button to go
up one level.
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
The menu selection level display appears on the
monitor.
In the figure below, “SETUP MENU” is selected
(shown in reverse video).
The time counter display of this unit shows only the
currently selected item. When the item name is long, it
is abbreviated.
RESET (NO) button
SET (YES) button
• Returns the setting to the
factory default setting.
• Sends a negative
Menu selection level display
response to prompts on
the monitor screen.
SYSTEM MENU
Setup menu
SETUP MENU
AUTO FUNCTION
Time counter display
• Saves the new setting in
memory.
HOURS METER
• Sends a positive response
to prompts on the monitor
screen.
Monitor screen
Changing Menu Settings
78
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the G button.
5 Press the for Fbutton to select the itemwhose setting
you wish to change.
This displays all items on menu level 1.
For menu items on level 3, press the Gbutton to go to
level 3, then press the for F button to select the item
whose setting you wish to change.
Level-1 menu display
SETUP MENU
Operational
OPERATIONAL FUNCTION
Example: Display when “BRIGHTNESS” is selected
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP MENU
> Brightness
DISPLAY CONTROL
SETUP BANK OPERATION
CHARA.DISPLAY :ON
Time counter display
MENU GRADE
:BASIC
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
:T&STA
:OFF
:WHITE
:OFF
Monitor screen
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
3 Press the f or F button to select the required item.
Monitor screen
Example: Display when “DISPLAY CONTROL” is selected
6 Press the G button.
This displays all possible settings for the item selected
in step 5.
SETUP MENU
Display
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP BANK OPERATION
SETUP MENU
>> 75%
DISPLAY CONTROL
MENU GRADE
:BASIC
BRIGHTNESS
100%
:75%
Time counter display
* 75%
50%
Monitor screen
4 Press the G button.
Monitor screen
This displays menu level 2 for the menu item selected
in step 3.
7 Press the f or F button to change the setting of the
item.
Example: Level-2 display for “DISPLAY CONTROL”
SETUP MENU
> Chara disp
DISPLAY CONTROL
SETUP MENU
>> 50%
DISPLAY CONTROL
CHARA.DISPLAY :ON
Time counter display
BRIGHTNESS
100%
:75%
Time counter display
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
SUB STATUS
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
* 75%
50%
:T&STA
:OFF
Current settings
:WHITE
:OFF
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
Monitor screen
Monitor screen
Changing Menu Settings
79
Download from Www.Somanuals.com. All Manuals Search And Download.
8 To change other settings, press the g button to return
to the previous screen, then repeat steps 5 to 7 as
required.
Displaying Enhanced Items
The factory default setting is not to display enhanced
items.
9 When you have completed the settings, press the SET
To display enhanced items, set the MENU GRADE menu
procedure in the previous section “Changing the Settings
of Basic Items.” (In step 3, first select “MENU GRADE,”
and next select “ENHANCED,” then press the SET (YES)
button to save the setting in memory.)
(YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
With this done, when you press the MENU button and the
Gbutton to display the setup menu, all basic and enhanced
items on menu level 1 appear.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
Notes
Changing the Settings of Enhanced
Items
• If you power off the unit before saving operation is
completed, settings may be lost. Wait until the
saving is completed before powering off the unit.
• If, instead of pressing the SET (YES) button, you
press the MENU button, the new settings are not
saved. The message “ABORT !” appears on the
monitor screen and “Abort !” in the time counter
display for about 0.5 second, and the system exits
the menus. To change more than one setting, be sure
to press the SET (YES) button after making the
settings.
To change the settings of enhanced items, first carry out
the procedure in the previous section “Displaying
Enhanced Items,” then proceed as follows.
MENU
RESET(NO)
1
TC
PRESET
SET(YES)
4
2
Meanings of indications on the monitor
screen
On-screen indication
Meaning
3
Right-pointing arrow (c) at
the right of a menu item
See step 1 of the foregoing
operating procedure.
Pressing the G button
switches to the next lower
menu level or to a setting
selection screen.
Left-pointing arrow (C) at the Pressing the g button
left of a menu item
See step 4 of the foregoing
operating procedure.
returns to the previous
(higher) menu level.
1 Press the MENU button in the menu control section.
The menu selection level display appears on the
monitor.
Character string at the right of Current setting of the menu
a menu item
item
See step 4 of the foregoing
operating procedure.
When shown with a colon
(:): the current setting is
the same as the factory
default setting.
When shown with a raised
dot (•): the current
setting is different from
the factory default
setting.
See step 2 of the
operating procedure in
An asterisk in a complete list Factory default setting
of settings
See step 6 of the foregoing
operating procedure.
Changing Menu Settings
80
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the G button.
To return all settings to their factory
default settings
This displays all basic and enhanced items on menu
level 1.
1 Press the MENU button in the menu control section.
Level-1 menu display
The menu selection level display appears on the
monitor screen.
SETUP MENU
Menu grade
OPERATIONAL FUNCTION
DISPLAY CONTROL
2 Press the Gbutton to display level 1 of the setup menu.
3 Press the RESET (NO) button.
Time counter display
TIME CODE
TAPE PROTECTION
VIDEO CONTROL
AUDIO CONTROL
DIGITAL PROCESS
SETUP BANK OPERATION
A message appears, to confirm whether or not you
wish to return all settings to their factory default
settings.
ENHAN
MENU GRADE
Current setting
Monitor screen message Message in the time
counter display
Monitor screen
INITIALIZE ALL ITEMS TO Init setup?
FACTORY PRESET
VALLUES?
3 Follow the same procedure as in steps 3 to 8 of the
procedure in the section “Changing the Settings of
select an item and change its setting.
4 Press the SET (YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
4 When you have completed the settings, press the SET
(YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
Note
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the saving is
completed before powering off the unit.
To abandon the resetting operation
Returning Menu Settings to Their
Factory Default Settings
Instead of pressing the SET (YES) button, press the
RESET (NO) button. The display returns to menu
level 1, leaving the settings unchanged.
After making menu setting changes, to return settings to
their factory default settings (setting initialization), use the
following procedure.
To return a particular setting to its factory
default setting
In the section “Changing the Settings of Basic Items”
the current setting displayed (in the example, if the factory
default setting has been changed, the current setting will be
100% or 50%), proceed as follows.
1 Either press the RESET (NO) button or select the
default setting using the f or F button.
2 Press the SET (YES) button.
The setting returned to its factory default is saved in
memory as the current setting.
Changing Menu Settings
81
Download from Www.Somanuals.com. All Manuals Search And Download.
When the SUB STATUS menu item is set to TC MODE:
Displaying
Supplementary Status
Information
On-screen
indication
Meaning
INT PRST FREE
[IP F]
The internal time code generator is
operating in FREE RUN mode.
INT PRST REC
[IP R]
The internal time code generator is
operating in REC RUN mode.
When you set the SUB STATUS menu item (see page 67)
to other than OFF, you can view supplementary status
information on the monitor screen below the operating
mode display area.
INT REGEN-T&U
[IRTU]
The internal time code generator is in
synchronization with the playback
time code (LTC) read from tape.
EXT LTC-T&U
[ELTU]
The internal time code generator is in
synchronization with the external time
code (LTC) input to the unit and is
generating the same time code value
and user bit value as those of the
external time code (regeneration).
.
.
T C R
0 0
P L A Y
I N S
:
0 4
A 1
4 7
L O C K
3 4 T C
0 7
2
V
EXT VITC-T&U
[EVTU]
The internal time code generator is in
synchronization with VITC present in
the external video signal input to the
unit and is generating the same time
code value and user bit value as
those of the external time code
(regeneration).
Supplementary status information
The following items of supplementary status information
are displayed depending on the setting of the SUB
STATUS menu item.
EXT QSDI-T&U
[EQTU]
The internal time code generator is in
synchronization with the external time
code input to the unit via the SDTI
(QSDI) interface and is generating the
same time code value and user bit
value as those of the external time
code (regeneration).
Setting of SUB
STATUS menu item
Items of supplementary
information displayed
EDIT PRESET
TC MODE
Editing mode settings made on the
editing control unit
EXT QSDI. V-T&U
[EQTU]
The internal time code generator is in
synchronization with the external
VITC input to the unit via the SDTI
(QSDI) interface and is generating the
same time code value and user bit
value as those of the external time
code (regeneration).
Operating mode of the internal time
code generator
REMAIN
AUDIO MIXING
ALL
Remaining capacity of the tape
Setting for input audio mixing
All of the above items
EXT DVIN-T&U
[EDTU]
The internal time code generator is in
synchronization with the external time
code input to the unit via the i.LINK
(i.DV IN) interface and is generating
the same time code value and user bit
value as those of the external time
code (regeneration).
The following tables show the on-screen indications of
supplementary information and their meaning.
In each table, the indications given in brackets such as
[ASM] are the indications displayed when the SUB
STATUS menu item is set to ALL.
EXT DVIN. V-T&U
[EDTU]
The internal time code generator is in
synchronization with the external
VITC input to the unit via the i.LINK
(i.DV IN) interface and is generating
the same time code value and user bit
value as those of the external time
code (regeneration).
For the display format when ALL is selected, see the next
section.
When the SUB STATUS menu item is set to EDIT
PRESET:
On-screen
indication
Meaning
When the SUB STATUS menu item is set to REMAIN:
ASM
[ASM]
Assemble editing mode
On-screen
indication
Meaning
INS V A1234 TC
[V1234T]
INS: Insert editing mode
V A1234 TC: Channels or signals
selected for insert editing
V: Video
REMAIN 184 min
Remaining capacity of the tape in
minutes.
When the remaining capacity has not
been calculated, “REMAIN --- min”
appears.
A1234: Audio 1, 2, 3, 4
TC: Time code
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
82
When the SUB STATUS menu item is set to AUDIO
MIXING:
On-screen indication
Meaning
1 2 3 4
[MIX]
Input audio channels
selected for mixing
1 2 3 4: Input audio
channels 1, 2, 3 and 4
Example display:
12
2
3
34
Input audio channels 3 and
4 are mixed and recorded
on audio channel 4 on tape.
Input audio channel 3 is recorded
on audio channel 3 on tape.
Input audio channel 2 is recorded
on audio channel 2 on tape.
Input audio channels 1 and 2 are mixed and
recorded on audio channel 1 on tape.
Display format of supplementary status
information when the SUB STATUS menu
item is set to ALL
All items of supplementary status information are
displayed in the order shown below.
:
.
T C R
0 0
:
0 4
M I
4 7
0 7
P L A Y
L O C K
X
D
V 1 2 3 4 T
E
T U V
Editing mode settings
Operating mode of the internal
time code generator
(The rightmost “V” appears
when the VITC menu item (see
page 68) is set to ON.)
Setting for input audio mixing
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Displaying Supplementary Status Information
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Connections and
Settings Chapter
5
Connections for a Digital Non-Linear Editing System
This unit can be connected to an ES-7 EditStation to
configure a digital non-linear editing system.
If you use the SDTI (QSDI) interface with the optional
DSBK-1501 board installed in the unit, you can transfer
video, audio, time code, and other compressed data
between this unit and the ES-7.
The unit supports ClipLink functions, enabling index
pictures recorded on tape and ClipLink log data stored in
cassette memory to be transferred to the ES-7 in an instant.
For a general description of ClipLink functions, see the
appendix “ClipLink Guide” (page 113).
The following figure shows a connection diagram for a
non-linear editing system in which this unit serves as the
recorder.
For connections of the ES-7 and its peripheral devices
such as the ESBK-7011 Control Panel, the ESBK-7045
Disk Unit, etc., refer to your ES-7 Operating Instructions.
Note
The DSR-1500A/1500AP unit shown in the following
figure is fitted with the optional DSBK-1501 and DSBK-
1504/1504P boards.
Connections for a Digital Non-Linear Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Video monitor
Composite
video input
Audio input
1
3
VIDEO OUT
B-Y/CPST
(SUPER)
1
B B OUT(1/2/3/4)
QSDI OUTPUT
QSDI INPUT
MONITOR
1
1
REF.
VIDEO
IN
SDI/SDTI(QSDI)
IN
RECORDER
SDI/SDTI(QSDI)
OUT
REMOTE
ES-7 EditStation
DSR-1500A/1500AP
(recorder)
2
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Settings on the DSR-1500A/1500AP
Switch/menu item
Setting
LOCAL/REMOTE switch
REMOTE
(REMOTE indicator lights.)
DIGITAL OUTPUT menu item SDTI
(SDTI indicator lights.)
(9P indicator lights.)
For details of video/audio input and audio mode settings,
Connections for a Digital Non-Linear Editing System
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for a Cut Editing System
The following figure shows a cut editing system
configuration that includes two DSR-1500A/1500AP units
to serve as the player and recorder.
Notes
• This application requires both of the DSR-1500A/
1500AP units (recorder and player) to be fitted with the
optional DSBK-1501 board.
• The DSR-1500A/1500AP units shown in the following
figure are fitted with the optional DSBK-1501 and
DSBK-1504/1504P boards.
For details of connecting devices other than the DSR-
1500A/1500AP, refer to the instruction manual for each
device.
A 75 Ω coaxial cable (not supplied)
When you select assemble or insert editing mode on the editing
control unit, the two DSR-1500A/1500AP units (recorder and
player) will automatically enter the selected editing mode.
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Composite
video input
Composite
video input
Audio input
Audio input
Source monitor
Main monitor
1
3
1
3
VIDEO
VIDEO
OUT B-Y/CPST
(SUPER)
OUT B-Y/CPST
(SUPER)
MONITOR
MONITOR
SDI/SDTI
(QSDI)
OUT
SDI/SDTI
(QSDI)
IN
1
1
VIDEO OUT
Y/CPST
REF.
VIDEO IN
REMOTE
REMOTE
DSR-1500A/1500AP
(player)
DSR-1500A/1500AP
(recorder)
2
2
RECORDER
PLAYER
Editing control unit (RM-450/450CE,
a)
PVE-500, etc.)
a) For the settings on the editing control unit, see
Connections for a Cut Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
87
Settings on the DSR-1500A/1500APs (recorder
and player)
Switch/menu item
Setting
LOCAL/REMOTE switch
REMOTE
(REMOTE indicator lights.)
a)
DIGITAL OUTPUT menu item
SDTI
a)
(SDTI indicator lights.)
(9P indicator lights.)
b)
REC FORMAT menu item
DVCAM
(DVCAM indicator lights.)
b)
a) for player only
b) for recorder only
For details of the video/audio input and audio mode
settings for the recorder, see “Settings for Recording” on
About reference video signals
In order to provide stable video and audio signals for
analog editing, it is necessary for the built-in time base
corrector (TBC) to operate correctly. To ensure this, input
a reference video signal synchronized with the video signal
to the REF. VIDEO IN connector.
Connections for a Cut Editing System
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for an A/B Roll Editing System
The following is an example configuration of A/B roll
editing system using the DSR-1500A/1500AP.
In this configuration, two DSR-1500A/1500AP units are
used, one as the recorder and the other as player 1, and an
analog Betacam UVW-1600/1600P Videocassette Player
unit is used as player 2. To create a final tape (a tape that
contains a completely packaged program) in Betacam
format, use a BetacamVCRsuch as the UVW-1800/1800P
as the recorder.
Notes
• This application requires the DSR-1500A/1500AP unit
used as the recorder to be fitted with the optional DSBK-
1504/1504P board.
• The DSR-1500A/1500AP units shown in the following
figure are fitted with the optional DSBK-1501 and
DSBK-1504/1504P boards.
The purpose of the following figure is to indicate the flow
of signals among the component devices in the system.
The specific connections and settings are described
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Main video monitor
Source video monitor
Audio system monitor
Video signal generator
(Sony Tektronix TSG-
130, etc.)
DPS-D7 or otherdelay
a)
unit
DSR-1500A/1500AP
(recorder)
MXP-290Audio
Mixer
PVE-500, etc. (editing control unit)
DFS-500/500P
DME Switcher
UVW-1600/1600P
(player 2)
DSR-1500A/1500AP (player 1)
Video signal
Audio signal
Reference video signal
Control signal
a) When using a DFS-500/500P DME Switcher, the phase of the video signals processed by
the DFS-500/500P is delayed. It is therefore necessary to connect a delay unit between the
MXP-290 Audio Mixer’s output and the audio input to the DSR-1500A/1500AP (recorder).
Connections for an A/B Roll Editing System
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio monitor system connections
Reference video signal connection
The following shows an example of audio monitor system
connections.
When you perform recording, be sure to input a reference
video signal.
For details of these connections, refer to the instruction
manual for each connected device.
For details of reference video signals, see “About
DFS-500/500P DME Switcher
Speaker (right channel)
Speaker (left channel)
BLACK
BURST
4 3 2 1
OUT
DSR-1500A/1500AP (recorder)
Audio amplifier
REF. VIDEO
IN
R
R
L
L
Cables with RCA phono plugs
MONITOR
OUT 1
MONITOR
OUT 2
DSR-1500A/1500AP (player 1)
REF. VIDEO
IN
MXP-290 Audio Mixer
REF. VIDEO IN 75 Ω
termination switch: ON UVW-1600/1600P
(player 2)
REF. VIDEO IN
PVE-500 Editing Control Unit
REF.
VIDEO
IN
REF. VIDEO IN 75 Ω termination switch: ON
Use 75 Ω coaxial cables for all of these connections.
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Control signal connections
The following shows an example of control signal
connections to enable the editing control unit to control all
other A/B roll editing system devices.
DSR-1500A/1500AP (recorder)
a)
9-pin remote control cable
REMOTE
DSR-1500A/1500AP (player 1)
Mixer control mode
selection switch:
PARALLEL
a)
9-pin remote control cable
REMOTE
PVE-500 Editing
Control Unit
RECORDER
UVW-1600/1600P (player 2)
PLAYER 1
MIXER
SWITCHER
PLAYER 2
a)
REMOTE
9-pin remote control cable
DFS-500/500P DME Switcher
a)
EDITOR
9-pin remote control cable
MXP-290 Audio Mixer
9-pin/15-pin mixer control cable (not supplied)
EDITOR (15-pin)
a) For the 9-pin remote control cable, use an optional
RCC-5G/10G/30G cable.
Connections for an A/B Roll Editing System
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Video/audio signal connections
The following shows an example of video/audio signal
connections in an A/B roll editing system.
In this example, analog component signals are used as the
video signals and XLR 3-pin connectors are used as audio
input/output connectors.
VIDEO IN
VIDEO INPUTS
COMPONENT 2
1
DFS-500/500P DME Switcher
AUDIO IN
2/4
1/3
PGM OUT
COMPONENT 1
3
3
VIDEO INPUTS
COMPONENT 1
DSR-1500A/1500AP
(recorder)
1
2
CH-1 OUT
DPS-D7 or other delay unit
CH-1 IN CH-2 IN
CH-2 OUT
DSR-1500A1500AP
(player 1)
VIDEO OUT
3
3
LINE OUT 2
LINE OUT 1
AUDIO OUT
1/3 2/4
MIC/LINE 4
IN
3
2
1
MXP-290
Audio Mixer
3
3
3
3
COMPONENT 1
OUTPUT
A 12-pin/3-BNC cross cable
(not supplied; consult your
Sony dealer about this cable.)
B 12-pin dubbing cable
(not supplied)
AUDIO OUTPUT
CH-1
C Cable with XLR
connectors (not supplied)
CH-2
UVW-1600/1600P (player 2)
Settings on the DSR-1500A/1500AP (recorder)
For details of the video/audio input and audio mode
Switch/menu item
Setting
LOCAL/REMOTE switch
LOCAL
CH1 IN LEVEL and CH2 IN
LEVEL menu items (see page
Normally +4 dBm
REC FORMAT menu item
DVCAM
(DVCAM indicator lights.)
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
93
Settings on the DSR-1500A/1500AP (player)
Connection of a video monitor
Set up the following connections to enable monitoring of
video and audio signals on a video monitor. In addition to
the video and audio signals, you can have time data, the
operation mode of the unit, alarm messages, and other
information displayed as text on the monitor screen by
setting the CHARA. DISPLAY menu item (see page 66)
to ON (factory default setting).
Switch/menu item
Setting
LOCAL/REMOTE switch
LOCAL
OUTPUT LEVEL menu item
Normally +4 dBm
VIDEO OUTPUT menu item
Y−R, B
(Y−R,B indicator lights.)
AUDIO OUTPUT menu item
1/2 CH or 3/4 CH
(CH 1/2 or CH 3/4 indicator
lights.)
75 Ω termination switch: ON (or attach a 75 Ω terminator)
Input switches: Set according to the type of input signals.
Video monitor
Composite
video input
Audio input
2
1
VIDEO
OUT
B-Y/CPST
(SUPER)
MONITOR
DSR-1500A/1500AP (recorder)
A Cable with RCA phono plugs
(not supplied)
B 75 Ω coaxial cable
(not supplied)
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
94
Settings on an editing control unit
When connecting an editing control unit, make the settings
as follows, according to the model.
PVE-500
No settings are required.
BVE-600/900/910/2000 (NTSC model) or FXE-100/
120
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
80 17 00 96 05 05 03 80 0A 08 FE 00 80 5A FF
BVE-600/900/910/2000 (PAL model) or FXE-100P/
120P
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
81 17 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF
RM-450/RM-450CE
Set the DIP switches as follows.
• Left switches
7
6
5
4
3
2
1
0
OFF
−
−
OFF
−
−
−
−
• Right switches (RM-450)
)
7
6
5
4
3
2
1
0
OFF
−
OFF
ON
OFF
OFF
ON
ON
• Right switches (RM-450CE)
7
6
5
4
3
2
1
0
ON
−
OFF
ON
OFF
OFF
ON
ON
BVE-800
Set the DIP switches as follows.
• SW2
1
2
3
4
5
6
7
8
ON
OFF
ON
ON
−
ON
ON
−
• SW3 (NTSC model)
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
−
ON
OFF
OFF
• SW3 (PAL model)
1
2
3
4
5
6
7
8
OFF
OFF
OFF
ON
−
ON
OFF
OFF
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
95
Connections for SDTI (QSDI) Dubbing
The following shows an example of connections for
a pair of DSR-1500A/1500AP units.
Notes
• This application requires both of the DSR-1500A/
1500AP units (recorder and player) to be fitted with the
optional DSBK-1501 board.
• The DSR-1500A/1500AP units shown in the following
figure are fitted with the optional DSBK-1501 and
DSBK-1504/1504P boards.
DSR-1500A/1500AP (player)
SDI/SDTI
(QSDI)
OUT
REMOTE
2
DSR-1500A/1500AP
REMOTE (recorder)
1
SDI/SDTI
(QSDI)
IN
VIDEO OUT
B-Y/CPST
(SUPER)
MONITOR
3
1
Composite
video input
Audio input
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Video monitor
Settings on the DSR-1500A/1500AP (recorder)
Settings on the DSR-1500A/1500AP (player)
Switch/menu item
Setting
Switch/menu item
Setting
LOCAL/REMOTE switch
LOCAL
LOCAL/REMOTE switch
REMOTE
(REMOTE indicator lights.)
DIGITAL OUTPUT menu item SDTI
(SDTI indicator lights.)
(9P indicator lights.)
Connections for SDTI (QSDI) Dubbing
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for Analog Recording
It is possible to record analog playback signals from
another recorder or player on this unit. The following
shows connections for a system in which analog
component video signals and two channels of audio signals
are recorded between two DSR-1500A/1500AP units.
Notes
• This application requires the DSR-1500A/1500AP unit
used as the recorder to be fitted with the optional DSBK-
1504/1504P board.
• The DSR-1500A/1500AP units shown in the following
figure are fitted with the optional DSBK-1501 and
DSBK-1504/1504P boards.
Video monitor
A Cable with RCA phono plugs
(not supplied)
B 75 Ω coaxial cable
(not supplied)
C Cable with XLR connectors
(not supplied)
Composite
video input
Audio input
1
2
2 a)
VIDEO
OUT
B-Y/CPST
(SUPER)
MONITOR
VIDEO OUT
VIDEO IN
2/4
AUDIO OUT
1/3
AUDIO IN
DSR-1500A1500AP
(recorder)
DSR-1500A/1500AP (player)
2/4
1/3
3
3
a) Three 75 Ω coaxial cables are used,
one each for Y, R−Y, and B-Y.
Settings on the DSR-1500A/1500AP (recorder)
For details of the video/audio input and audio mode
Switch/menu item
Setting
LOCAL/REMOTE switch
LOCAL
CH1 IN LEVEL and CH2 IN
LEVEL menu items (see page
Normally +4 dBm
(REC MODE 2CH indicator
lights.)
REC FORMAT menu item
DVCAM
(DVCAM indicator lights.)
Connections for Analog Recording
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings on the DSR-1500A/1500AP (player)
Switch/menu item
Setting
LOCAL/REMOTE switch
LOCAL
OUTPUT LEVEL menu items Normally +4 dBm
VIDEO OUTPUT menu item Y−R, B
(Y−R,B indicator lights.)
AUDIO OUTPUT menu item 1/2 CH or 3/4 CH
(CH 1/2 or CH 3/4 indicator
lights.)
Connections for Analog Recording
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Sync and Subcarrier Phases
When using two or more players, as in an A/B roll editing
system, it is necessary to synchronize the sync and
subcarrier (for composite signals) phases of the signals to
be edited. If they are not synchronized, picture instabilities
or color break-up may occur at edit points.
After configuring the editing system, use a vectorscope to
adjust the sync and subcarrier phases of the recorder and
players. Subcarrier phase adjustment is necessary when
using composite signals and Y/C signals.
DSR-1500A/1500AP (player 1)
a)
Switcher (DFS-500/500P)
DSR-1500A/1500AP (recorder)
UVW-1600/1600P (player 2)
b)
75 Ω coaxial cable (A)
b)
75 Ω coaxial cable (B)
Vectorscope (Sony Tektronix
1750/1751, etc.)
PVE-500 Editing Control Unit
a) The sync and subcarrier phases of the
output signal from the DFS-500/500P
switcher are automatically adjusted.
b) Ensure that the 75 Ω coaxial cables (A) and
(B) (not supplied) are of the same length.
Adjusting the Sync and Subcarrier Phases
Download from Www.Somanuals.com. All Manuals Search And Download.
99
Performing a phase adjustment operation
Note
When component signals are used the subcarrier phase
indicator does not appear.
1 Press the SCH button on the vectorscope.
The vectorscope switches to SCH mode.
8 Output the player 2 signal from the PVE-500, and
repeat steps 6 and 7 to adjust the sync and subcarrier
phases of the output from player 2.
2 Press the B channel button on the vectorscope.
This displays the black burst signal from the switcher.
3 Press the EXT button on the vectorscope.
This switches the vectorscope to external
synchronization mode.
4 Adjust the phase synchronization control on the
vectorscope so that the sync and subcarrier phases are
close to the reference line.
Sync phase
Subcarrier phase
Reference line
Align the sync and subcarrier phases of the black
burst signal to the reference line.
5 Output the player 1 signal from the PVE-500.
6 Press the A channel button on the vectorscope.
This displays the sync and subcarrier phases
(composite signals only) of the signal from player 1.
7 On player 1, adjust the front panel SYNC PHASE and
SC PHASE controls, using a Phillips screwdriver, so
that the output from player 1 on channel A is in correct
phase alignment with the black burst signal on channel
B.
This indicator
This indicator
moves as you
moves as you
turn the SYNC
turn the SC
PHASE control.
PHASE control.
Adjust the sync and subcarrier phases of the output
signal from player 1.
Adjusting the Sync and Subcarrier Phases
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and
Troubleshooting Chapter
6
Regular Checks
Maintenance
Digital hours meter
The digital hours meter keeps cumulative counts of the
total operating time, the head drum rotation time, the tape
transport operating time, and the number of threading/
unthreading operations. These counts can be displayed on
the monitor screen and in the time counter display of this
unit. Use them as guidelines for scheduling maintenance.
In general, consult your Sony dealer about necessary
periodic maintenance checks.
Condensation
If you move the unit suddenly from a cold to a warm
location, or if you use it in a very humid place, moisture
from the air may condense on the head drum. This is called
condensation, and if a tape is run in this state, the tape may
stick to the drum and can be easily damaged. To lessen the
risk of this occurring, this unit is equipped with a
condensation detection system.
Digital hours meter display modes
The digital hours meter has the following four display
modes.
If condensation occurs while the unit is
operating:
• T1 (OPERATION) mode
The alarm message “MOISTURE HAS BEEN
DETECTED.” appears on the monitor screen, and the
alarm message “HUMID!” in the time counter display. At
the same time the unit ejects the cassette automatically. If
this happens, leave the unit powered on and wait until the
alarm messages disappear.
The cumulative total hours during which the unit is
powered on is displayed in 10-hour increments.
• T2 (DRUM ROTATION) mode
The cumulative total hours of drum rotation with tape
threaded is displayed in 10-hour increments.
• T3 (TAPE RUNNING) mode
The cumulative total hours of tape transport operation
for fast forward, rewind, playback, and search (except in
still search mode) is displayed in 10-hour increments.
• CT (THREADING) mode
The cumulative number of tape threading/unthreading
operation pairs is displayed in 10-operation pair
increments.
If the condensation alarm message appears
immediately after powering on:
Leave the unit powered on and wait until the alarm
message disappears. You cannot load a cassette into the
unit while the alarm message is being displayed.
Once the alarm message disappears, the unit is ready for
use.
For all modes except T1 (OPERATION), there are two
types of count: a “trip” count, which is resettable, and the
cumulative total from manufacture, which is unresettable.
Maintenance
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital hours meter indications on the monitor
Displaying the digital hours meter
Use the following procedure.
screen
All four counts (T1, T2, T3, and CT) are indicated on the
monitor screen.
1 Press the MENU button in the menu control section.
The menu selection level display appears on the
monitor screen and in the time counter display.
Resettable trip counts
Unresettable counts
HOURS METER
Menu selection level display
T1
00000 X10 HOURS
T2 0000/00000 X10 HOURS
T3 0000/00000 X10 HOURS
CT 0000/00000 X10 COUNT
SYSTEM MENU
Setup menu
SETUP MENU
AUTO FUNCTION
Time counter display
HOURS METER
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
The four-digit value to the left of the slash (/) is the
resettable trip count, and the right value is the cumulative
total from manufacture.
Monitor screen
2 Press the F button to select “HOURS METER.”
Digital hours meter indications in the time
counter display
SYSTEM MENU
Hours meter
SETUP MENU
One of the four indications appears in the time counter
display at a time. Use the f and F buttons in the menu
control section to change the item displayed.
Initially, only the trip value appears. Hold down the G
button to display also the cumulative total from
manufacture, which will appear to the right of the trip
value and the slash (/).
AUTO FUNCTION
Time counter display
HOURS METER
The following illustrates the digital hours meter
indications in the time counter display in all four display
modes. The right-hand indication for each display mode is
the indication you can view while holding down the G
button in the menu control section.
Monitor screen
3 Press the G button.
T1 (OPERATION) mode:
The cumulative counts by the digital hours meter are
indicated on the monitor screen and in the time counter
display.
Oper. 00000
T2 (DRUM ROTATION) mode:
Drum 0000
0000/00000
0000/00000
T3 (TAPE RUNNING) mode:
Tape 0000
CT (THREADING) mode:
Thread 0000
0000/00000
Maintenance
102
Download from Www.Somanuals.com. All Manuals Search And Download.
To end the digital hours meter display
Press the MENU button in the menu control section.
To reset the trip values
About this operation, consult your Sony dealer.
Head Cleaning
Always use the DVM12CL (mini size) or DV12CL
(standard size) Cleaning Cassette to clean the video and
audio heads. You can run the cleaning cassette for 10
seconds per cleaning operation. Follow the instructions for
the cleaning cassette, as inappropriate use of the cleaning
cassette can damage the heads.
To clean the heads
Insert the cleaning cassette. This automatically starts
cleaning. You cannot operate any tape transport control
buttons other than the EJECT button during the cleaning
operation.
After about 10 seconds, the cleaning cassette will be
automatically ejected.
Maintenance
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If an alarm message appears on the monitor screen, or if
the unit appears to be malfunctioning, please check the
following before contacting your Sony dealer.
Tape problems
Symptom
Cause
Remedy
Recording is not
possible.
The cassette’s REC/SAVE switch is set Set the REC/SAVE switch to REC, or use another cassette.
to SAVE.
The unit’s tape
transport control
The REMOTE indicator in the display
section is lit and the LOCAL ENABLE REMOTE indicator off, or change the setting of the LOCAL
Set the LOCAL/REMOTE switch to LOCAL to turn the
buttons (PLAY, F FWD, menu item is set to STOP & EJECT or ENABLE menu item (see page 65) to ALL ENABLE.
REW, etc.) do not
work.
ALL DISABLE.
No cassette is loaded.
The NO EDIT indicator The audio recording mode selected on • When your current purpose is editing, set the LOCAL/
on the front panel lights this unit does not coincides with that of
REMOTE switch to LOCAL to turn the REMOTE indicator
off and set the unit for the same audio recording mode as
with the tape using the REC MODE menu item (see page
71), then set the switch to REMOTE to light the REMOTE
indicator again.
up.
the loaded tape.
• When your current purpose is recording, you can use the
tape currently loaded in the unit.
The recording format of the currently
loaded tape is DV or DVCPRO.
Replace the tape with one recorded in the DVCAM format.
The recording format selected on this
unit is DV (SP).
Select the DVCAM format.
Time data problems
Symptom
Cause
Remedy
Cannot freely set the
initial time data value. REGEN.
CNT is selected as the time data type Press the COUNTER SELECT button to make the TC or U-
to be displayed (the COUNTER time
data type indicator is lit).
BIT time data type indicator light up (the CNT value cannot
be set freely).
The REMOTE indicator in the display
Set the LOCAL/REMOTE switch to LOCAL to turn the
section is lit and the LOCAL ENABLE REMOTE indicator off or change the setting of the LOCAL
ALL DISABLE.
The tape is running,
The MENU button or TC PRESET
Press the button once again to exit the menu control mode,
but the time data is not button in the menu control section has time code preset mode, or digital hours meter display mode.
shown in the time
counter display.
been pressed.
(In either of the menu control mode and time code preset
mode, the time data is not shown in the time counter display.)
The U-BIT time data type indicator is lit. Press the COUNTER SELECT button to make the
COUNTER or TC time data type indicator light up.
Input problem
Symptom
Cause
Remedy
It is not possible to
No SDTI signal is input to the unit, or
Connect an SDTI signal to the SDI/SDTI (QSDI) IN
record an SDTI (QSDI) the SDTI format has not been selected. connector, or set the DIGITAL OUTPUT menu item (see
signal.
page 73) to SDTI.
Troubleshooting
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor problems
Symptom
Cause
Remedy
Data is not
superimposed on the
monitor screen.
The CHARA. DISPLAY menu item is
set to OFF.
The monitor is not connected to the
B−Y/CPST (SUPER) connector of this (You must make this connection to display any type of text on
unit.
Connect the monitor to the B−Y/CPST (SUPER) connector.
the monitor.)
The image on the
monitor screen is too
bright.
The 75 Ω termination switch for video
input on the monitor is in the OFF
position, or a 75 Ω terminator is not
fitted to its video input connector.
Set the 75 Ω termination switch to ON or connect a
terminator.
The image on the
monitor screen is too
dark.
In a video signal loop-through
Set the 75 Ω termination switches to OFF on all monitors
other than the loop-end monitor.
connection of video monitors, 75 Ω
termination switches for video input on
monitors other than the loop-end
monitor are in the ON position.
The image is too dark
when recording a
composite video
signal.
Audio problem
Symptom
Cause
Remedy
The REC/PB LEVEL
control knobs do not
work.
The VAR switch on the front panel is
set to PRESET.
Set the VAR switch to REC when recording, or set it to PB
when playing back.
Editing restriction
Symptom
Cause
Execution of video
This phenomenon cannot be avoided with an editing system using this unit as the recorder.
editing in insert mode
erases subcode data
(user bit data, etc.)
recorded on tape other
than time code data.
Troubleshooting
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
This unit is provided with a self-diagnostic function that
detects internal abnormalities. When it detects an
abnormality, it outputs an error message to the monitor
screen and indicates an error code in the time counter
display.
Note
To display error messages on the monitor screen, connect
the monitor to the B−Y/CPST (SUPER) connector, and set
(factory default setting).
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
02-603
Error message
Error code
PRESS EJECT KEY
TO EJECT TAPE.
Direction
Error code
Error02-603
Time counter display
Monitor screen
If an error message appears, follow the direction indicated
on the monitor screen.
Alarm Messages
When operating this unit, the unit may sometimes output
alarm messages such as the one shown below to the
monitor screen and the time counter display.
ALARM
Cause of
alarm
REMOTE MODE IS SELECTED.
Direction
SET REMOTE/LOCAL SWITCH
TO LOCAL.
REMOTE!
Time counter display
Monitor screen
If such an alarm message appears, a connection or
operation error may have been made, or condensation on
heads may have occurred. Follow the direction indicated
on the monitor screen.
Note
To display alarm messages on the monitor screen, it is
necessary for the monitor to be connected to the B−Y/
CPST (SUPER) connector, and set the following menu
items to ON.
Troubleshooting
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm messages and associated directions
Direction
Alarm message on monitor screen
(Cause)
Alarm message in time
counter display
A cleaning tape has been inserted.
The tape will automatically be ejected after cleaning is Cleaning Tp!
completed.
A non-standard signal is being used for Use a standard signal.
input video.
VIN NON-STD
REF NON-STD
ILL. SETUP!
A non-standard ref. signal is being used Use a standard signal.
for REF. VIDEO.
Abnormal settings selected in setup
menu.
Correct the setup menu settings. Contact your Sony
dealer if this alarm message appears again after
making corrections.
Audio mixing mode cannot be changed
during recording.
−
REC mode!
Audio not editable on this tape.
Use a tape recorded in 2-channel/48 kHz or
4-channel/32 kHz mode.
2CH/32kHz!
Fs 44.1kHz!
Use a tape having audio signals recorded in locked
mode.
UNLOCK mode
Audio REC mode selection different from Select the same audio recording mode as that of the A mode err
audio on tape.
tape.
Audio REC (recording) mode cannot be
changed during recording.
−
REC mode!
Adaptor!
Cassette adaptor not usable.
Counter mode is selected.
Use a tape without cassette adaptor.
Use the COUNTER SELECT button to light the TC or CNT mode!
U-BIT time data type indicator in the display section.
Input selection cannot be changed in
REC (recording) mode.
−
−
−
−
REC mode!
Input signal does not conform to
DVCAM/DV format.
Unknown Sig
Input signal is 625/50. (For DSR-1500)
625/50 sig! (For DSR-
1500A)
Input signal is 525/60. (For DSR-
1500AP)
525/60 sig! (For DSR-
1500AP)
Input video is not detected.
Check the VIDEO indicator in the INPUT signal
display section and supply an appropriate video
signal.
No INPUT!
Input video signal does not synchronize Use a reference video signal.
with REF. VIDEO signal.
ILL. REF!
Moisture has been detected.
Keep the power on and wait until this alarm message HUMID!
disappears.
No cassette in VTR.
Load a cassette.
No Cass.!
Non DVCAM/DV(SP) format source.
Rec inhibit mode is selected.
−
No DVCAM/DV
REC INHI.!
OFF.
Record inhibit plug on the cassette is set Set the REC/SAVE switch on the cassette to REC.
to inhibit.
REC INHI.!
Remote mode is selected.
Set the LOCAL/REMOTE switch to LOCAL.
REMOTE!
Select DVCAM recording format.
DVCAM.
Not DVCAM!
Tape cannot be replayed.
Use a tape recorded in 525/60 format. (For DSR-
1500A)
625/50 Tape (For DSR-
1500A)
Use a tape recorded in 625/50 format. (For DSR-
1500AP)
525/60 Tape (For DSR-
1500AP)
Troubleshooting
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm messages and associated directions
Direction
Alarm message on monitor screen
(Cause)
Alarm message in time
counter display
Tape end has been detected.
Tape not editable.
Use a new cleaning tape.
Tape end!
Use a tape recorded in DVCAM format.
Not DVCAM!
Use a tape recorded in 525/60 format. (For DSR-
1500A)
625/50 Tape (For DSR-
1500A)
Use a tape recorded in 625/50 format. (For DSR-
1500AP)
525/60 Tape (For DSR-
1500AP)
Tape not recordable.
Tape not usable.
Use a DVCAM/DV ME tape.
REC INHI.!
ILL. Tape!
TC EXT!
Use a DVCAM/DV/DVCPRO (25 Mbps) tape.
TC EXTERNAL is selected.
PRESET.
TCG REGEN mode is selected.
PRESET.
REGEN mode!
REC RUN!
TCG RUN mode is set to REC RUN.
FREE RUN.
Troubleshooting
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendixes
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent shock
to it, is likely to cause it to malfunction.
Precautions
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilation openings, by for example wrapping the unit in
a cloth while it is in operation.
On safety
• Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be used
for an extended period of time.
On cleaning
If the casing or panel is dirty, wipe it gently with a soft dry
cloth. In the event of extreme dirt, use a cloth steeped in a
neutral detergent to remove the dirt, then wipe with a dry
cloth. Applying alcohol, thinners, insecticides, or other
volatile solvents may result in deforming the casing or
damaging the finish.
• To disconnect the cord, pull it out by the plug. Never pull
the cord itself.
On operation and storage locations
Avoid operation or storage in any of the following places.
• Location subject to extremes of temperature (operating
temperature range 5ºC to 40ºC (41ºF to 104ºF))
• Location subject to direct sunlight for long periods, or
close to heating appliances (Note that the interior of a car
left in summer with the windows closed can exceed 50ºC
(122ºF).)
On repacking and shipping
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your unit.
For maximum protection, repack your unit as it was
originally packed at the factory, and take care not to impart
violent shocks in transit.
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating strong
electromagnetic emissions
• Location near transmitting stations generating strong
radio waves
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through an
excessive angle (exceeding 20º).
Precautions
109
Download from Www.Somanuals.com. All Manuals Search And Download.
External dimensions (w/h/d)
211 × 137 × 420 mm
Specifications
3
1
5
(8 / × 5 / × 16 / inches)
8
2
8
General
Signal system DSR-1500A: NTSC
DSR-1500AP: PAL
Power requirements
100 V to 240 V AC, 50/60 Hz
Power consumption (with all options installed)
55 W
Peak inrush current
(1)Power ON, current probe method:
10 A (100 V), 45 A (240 V)
(2)Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
20 A (230 V)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage temperature
−20ºC to +60ºC (−4ºF to +140ºF)
Operating relative humidity
Less than 80%
Storage relative humidity
Less than 90%
211(8 3/8
)
Mass
6.0 kg (13 lb 3 oz)
Unit: mm (inches)
Tape transport control system
Tape speed
DSR-1500A: 28.193 mm/s
DSR-1500AP: 28.221 mm/s
Recording/playback time (DVCAM format)
Using PDV-184ME standard-size
cassette:
Maximum 184 minutes
Using PDVM-40ME mini-size cassette:
Maximum 40 minutes
Fast forward/rewind time
Using PDV-184ME standard-size
cassette:
Less than 3 minutes
Using PDVM-40ME mini-size cassette:
Less than 1 minute
Search speed When controlling via RS-422A interface:
Maximum 60 times normal speed in
both directions
When controlling from DSRM-10
Remote Control Unit:
Jog mode: 0 (still) to 2 times normal
speed in both directions
Shuttle mode: 8 speeds from 0 (still) to
16 times normal speed in both
directions
Specifications
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog video inputs
Video performance
Band width Composite/S-video (DSR-1500A):
REF. VIDEO IN
BNC type (×2, loop-through with 75 Ω
automatic terminator)
Black burst
0.286 V (DSR-1500A) or 0.3 V (DSR-
1500AP), 75 Ω, negative sync
Composite sync
30 Hz to 4.2 MHz 1.0 dB (Y)
Composite/S-video (DSR-1500AP):
25 Hz to 4.8 MHz 1.0 dB (Y)
Component (DSR-1500A):
30 Hz to 5.0 MHz 1.0 dB (Y),
30 Hz to 1.5 MHz +1.0/−5.0 dB (R−Y/
B−Y)
VIDEO IN (optional DSBK-1504/1504P Analog Input
Board required)
Component (DSR-1500AP):
25 Hz to 5.0 MHz 1.0 dB (Y),
25 Hz to 2.0 MHz +1.0/−2.0 dB (R−Y/
B−Y)
Composite/S-video I/O (Y):
52 dB or more
BNC type (×3 and 1 loop-through
connector with 75 Ω automatic
terminator), composite/component/S-
video switchable
S/N
Composite
Y/CPST and 1 loop-through connector
with 75 Ω automatic terminator: 1.0
Vp-p, 75 Ω, sync negative
Component
Component I/O (Y): 55 dB or more
30 ns or less
2.0% or less (K2T, KPB)
Y/C delay
K-factor
Y/CPST: 1.0 Vp-p, 75 Ω, negative sync
R−Y/C and B−Y: 0.7 Vp-p (75% color
bars for DSR-1500A or 100% color
bars for DSR-1500AP), 75 Ω
S-video
Processor adjustment range
Video level*
Chrome level* 3 dB/−∞ to 3 dB selectable
3 dB/−∞ to 3 dB selectable
Setup/Black level*
Y/CPST: 1.0 Vp-p, 75 Ω, negative sync
R−Y/C: 0.286 Vp-p (DSR-1500A) or 0.3
Vp-p (DSR-1500AP), 75 Ω (burst
level)
30 IRE ( 210 mV)
Chroma phase* 30°
System phase** Sync: 1 µs
SC: 180°
*
Adjust with menu settings.
Analog audio inputs
** Adjust with controls on the front panel.
AUDIO IN (optional DSBK-1504/1504P Analog Input
Board required)
Audio performance
Frequency response
XLR 3-pin, female (×2), +4/0/−3*/−6
dBm, high impedance, balanced
Two-channel (48 kHz) mode:
* For DSR-1500AP only
20 Hz to 20 kHz 1.0 dB
Four-channel (32 kHz) mode:
20 Hz to 14.5 kHz 1.0 dB
Time code input
TC IN
BNC type, SMPTE time code (DSR-
1500A) or EBU time code (DSR-
1500AP), 0.5 Vp-p to 18 Vp-p, 3.3 kΩ,
unbalanced
Dynamic range More than 87 dB
Distortion (THD + N)
Less than 0.07% (48 kHz)
Input connectors
Digital signal inputs
SDI/SDTI (QSDI) IN (optional DSBK-1501 Digital Input/
Output Board required)
BNC type
SDTI (QSDI) format (270 Mbps)
SDI format (270 Mbps), SMPTE 259M/
CCIR656-III
AUDIO (AES/EBU) IN (optional DSBK-1501 Digital
Input/Output Board required)
BNC type (×2), complying with AES-
3id-1995
i.DV IN/OUT
6-pin IEEE 1394 connector
Specifications
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Output connectors
Remote control connectors
REMOTE D-sub 9-pin, for connection of editing
control unit*, RS-422A standard
CONTROL S Stereo minijack, for connection of
SIRCS-compatible remote control unit
(DSRM-10)
Digital signal outputs
SDI/SDTI (QSDI) OUT (optional DSBK-1501 Digital
Input/Output Board required)
BNC type (×2)
SDTI (QSDI) format (270 Mbps)
SDI format (270 Mbps), SMPTE 259M/
CCIR656-III
i.DV IN/OUT 6-pin IEEE 1394 connector
* ES-7, PVE-500, RM-450/450CE, BVE-600/800/910/2000/9100/9100P,
etc.
AUDIO (AES/EBU) OUT (optional DSBK-1501 Digital
Input/Output Board required)
BNC type (×2), complying with AES-
3id-1995
i.DV IN/OUT 6-pin IEEE 1394 connector
Supplied accessories
AC power cord (1)
Operating Instructions (1)
Operating Instructions (CD-ROM) (1)
Analog video outputs
VIDEO OUT BNC type (×3), composite/component/
S-video switchable
Optional accessories
Composite
DSBK-1501 Digital Input/Output Board
DSBK-1504/1504P Analog Input Board
RCC-5G/10G/30G 9-pin remote control cable (length: 5 m
(16 ft)/10 m (33 ft)/30 m (98 ft))
Digital video cassette
Y/CPST, R−Y/C/CPST, and B−Y/CPST
(SUPER): 1.0 Vp-p, 75 Ω, sync
negative
Component
Y/CPST: 1.0 Vp-p, 75 Ω, negative sync
R−Y/C/CPST and B−Y/CPST (SUPER):
0.7 Vp-p (75% color bars for DSR-
1500A or 100% color bars for DSR-
1500AP), 75 Ω
Standard size: PDVM-64ME/94ME/
124ME/184ME
Mini size: PDVM-12ME/22ME/32ME/
40ME
Cleaning cassette
S-video
DV12CL (standard size), DVM12CL
(mini size)
Y/CPST: 1.0 Vp-p, 75 Ω, negative sync
R−Y/C/CPST: 0.286 Vp-p (DSR-1500A)
or 0.3 Vp-p (DSR-1500AP), 75 Ω
(burst level)
Related equipment
Analog audio outputs
ES-3/7 EditStation
AUDIO OUT XLR 3-pin, male (×2), +4/0/−3*/−6 dBm,
600 Ω loading, low impedance,
balanced
Linear editing control unit: PVE-500, RM-450/450CE,
BVE-600/800/910/2000/9100/9100P
DME switcher: DFS-300/300P, DFS-500/500P,
DFS-700/700P
MONITOR
Phono jack, −∞ to −11 dBu (DSR-
1500A)/−9 dBu (DSR-1500AP) 1
dB, 47 kΩ, unbalanced, −20 dBFS
(DSR-1500A)/−18 dBFS (DSR-
DXC-D30/D30P/D35/D35P Color Video Camera
DSR-1/1P Digital Videocassette Recorder
DSR-85/85P/70A/70AP/1800/1800P/2000/2000P Digital
Videocassette Recorder
DSR-1600/1600P Digital Videocassette Player
DSR-370/370P/570WS/570WSP/130/130P/ Digital
Camcorder
1500AP)
* For DSR-1500AP only
Output for headphones
DSRM-10 Remote Control Unit
HEADPHONES
Stereo phone jack, −∞ to −13 dBu (DSR-
1500A)/−11 dBu (DSR-1500AP), 8 Ω,
unbalanced, −20 dBFS (DSR-1500A)/
−18 dBFS (DSR-1500AP)
Design and specifications are subject to change without
notice.
Time code output
TC OUT
BNC type, SMPTE time code (DSR-
1500A), EBU time code (DSR-
1500AP), 2.2 Vp-p 3 dB, 600 Ω,
unbalanced
Specifications
112
Download from Www.Somanuals.com. All Manuals Search And Download.
High-speed transfer of recordings
It is also possible to transfer the editing material itself
between the DSR-85/85P and ES-7 at four times normal
speed. In other words, the transfer can be carried out in one
fourth of the real time duration. It is of course possible to
carry out a transfer at four times normal speed when
backing up video and audio data recorded on the disk drive
to the DSR-85/85P, or in the opposite direction when
loading data backed up on the DSR-85/85P to the disk
drive. Thus the time required is much shorter than with
conventional equipment (for which, for example,
transferring a 40-minute segment of video takes 40
minutes).
ClipLink Guide
What Is ClipLink?
The ClipLink function greatly improves the efficiency of
the video production process as a whole by recording
various editing-related data on tape when shooting. As
such, ClipLink is a revolutionary function that transcends
the conventional separation of shooting and editing.
How ClipLink Changes Video Production
Techniques
The following describes various ways in which ClipLink*
video production differs from conventional video
production.
* The ClipLink system is a video production system which uses the cassette
memory function.
Recording of ClipLink log data lightens the
shooting workload
When you start shooting a scene, ClipLink log data such as
the scene number and time code data are automatically
recorded into the cassette memory. This eliminates the
need for a conventional “shot list” compiled by someone
using a stopwatch, clipboard and pencil. You can also
designate unwanted scenes as “NG” (no good) and
automatically skip all “NG” scenes when editing.
Recorded index pictures drastically cut editing
time
The ClipLink function also features index pictures as a
time-saving tool for rough editing. Each index picture is a
compressed image taken from the start of each scene,
which is recorded onto the tape as a still picture. When
editing, begin by transferring only the index pictures and
the ClipLink log data to the EditStation’s hard disk. You
can also transfer OK scenes only (“NG” scenes are
skipped).
Next, begin rough editing by viewing the index pictures on
the EditStation’s GUI display and rearranging them as you
wish. This eliminates the difficult work of matching up a
handwritten shot list with recorded scenes. After you have
completed this rough editing, you can then transfer only
the recordings needed for your video program.
ClipLink Guide
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Example System Configuration and Operation Flow
The following illustration shows an example system
configuration for using the ClipLink function and a typical
ClipLink operation flow.
Shooting
DVCAM standard cassette or DVCAM mini cassette
DVCAM camcorder
(DSR-130/130P/
370/370P/570WS/
570WSP)
Index pictures: recorded on
tape
ClipLink log data: recorded in
cassette memory
ClipLink log data recorded onto DVCAM
cassettes links shooting and editing
operations.
ClipLink log data transfer
ES-7 EditStation non-
linear editing system
a)
DSR-85/1500A/1600 /1800/2000 or
a)
DSR-85P/1500AP/1600P /1800P/2000P
Digital Videocassette Recorder/Player
Index pictures
b)
Video output (SDTI)
ClipLink log data
RS-422A interface
Editing
ES-7 EditStation non-
linear editing system
c)
a)
a)
DSR-85 /1500A/1600 /1800/2000 or DSR-
c)
85P /1500AP/1600P /1800P/2000PDigital
Videocassette Recorder/Player
Actual AV data
b)
SDTI input/output
a) The DSR-1600/1600P is a videocassette player.
b) To transfer SDTI signals between the DSR-1500A/1500AP or DSR-1800/1800P and ES-7,
installation of the DSBK-1501 Digital Input/Output Board on the DSR-1500A/1500AP or the DSBK-
1802 SDTI (QSDI) Input/Output Board on the DSR-1800/1800P is required; to send an SDTI signal
from the DSR-1600/1600P to the ES-7, installation of the DSBK-1602 SDTI (QSDI) Output Board on
the DSR-1600/1600P is required.
c) Between the DSR-85/85P and ES-7, quadruple transfer is possible through the SDTI interface.
ClipLink Guide
114
Download from Www.Somanuals.com. All Manuals Search And Download.
ClipLink log data
Data Generated When Shooting
ClipLink log data can be recorded automatically or
manually into the cassette memory for use as a convenient
alternative to the conventional “shot list.”
The following describes the kinds of data that is generated
when using the ClipLink function.
ClipLink log data includes the following items.
Index pictures
ClipLink log data Description
When shooting, a single-frame image from the Mark IN
point at the start of each scene is recorded as a still picture
into the camcorder’s internal memory. These images are
called “index pictures.” When you finish shooting, the
index pictures from all scenes are recorded onto the tape
after the last scene.
Reel number
Data (maximum length: 8 digits)
(cassette number) consisting of alphanumeric characters
and/or symbols (This is left blank at
shipping.)
Scene number
A three-digit number from 001 to 198
(starts at 001 and is automatically
incremented with each scene.)
Take number
OK/NG
This cannot be changed (set to “1” at
shipping).
Tape
Indicates the OK/NG status of a
particular scene. (In the OK case,
nothing is recorded.)
Scene 1
Scene 2
Scene 3
Scene n
Mark IN/OUT
point time codes
These are the time codes that indicate
the Mark IN and Mark OUT points for
each scene (HH:MM:SS). These time
codes are recorded when the camera
has been set to MARK mode.
DVCAM camcorder’s
internal memory
After shooting, the index
pictures in the internal
memory are recorded onto
the video tape.
The time code value is rounded up at
each Mark IN point and rounded down
at each Mark OUT point, to a whole
number of seconds.
Up to 32 index pictures can be recorded onto the tape space
normally occupied by one frame, as shown below.
Cue point time
code
This is the time code that indicates the
cue points (valid up to the frame digit).
This time code is recorded when the
camera has been set to CUE mode.
When in this mode, the time codes at
the start and end of a recording (the
Rec IN and Rec OUT time codes) are
automatically recorded as Mark IN and
OUT points, respectively.
Index picture
0
90
180
270
360
450
540
630
(PAL) NTSC
(72) 60
1
2
3
4
5
6
7
8
(144) 120
(216) 180
(288) 240
(360) 300
(432) 360
(504) 420
9
10
14
18
22
26
30
11
15
19
23
27
31
12
16
20
24
28
32
13
17
21
25
29
720 dots
Seven frame spaces are reserved at the end of the last scene
as a recording area for index pictures. (A cassette with 16
Kbits of cassette memory can record up to 198 index
pictures, and a cassette with 4 Kbits of cassette memory
can record up to 45 index pictures.)
ClipLink Guide
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Cue point time codes
How to record ClipLink log data
This type of data is especially useful when shooting scenes
that may contain unexpected events, such as when
shooting for sports coverage or documentaries.
Set the camera to CUE mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, the current time code is recorded as a cue point
time code.
The following describes how to record the various
ClipLink log data items.
OK/NG status
To designate a scene as “NG,” press the NG button on the
camera while shooting the scene or at any time before you
begin shooting the next scene.
All scenes that do not receive an “NG” designation are
recorded as “OK” scenes.
(When you exit the VCR recording mode, changing the
OK/NG status is no longer possible.)
Start
recording
End
recording
Mark IN/OUT point time codes
Index picture 1
This data is especially useful when shooting a video
program for which a scenario has been created.
Set the camera to MARK mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, Mark IN and Mark OUT point time codes are
recorded alternately.
Scene 1
Take 1
Rec OUT
(automatic
recording)
Cue point
Index picture 1
Index picture 2
time code
(manual
recording)
Cue point
time code
(manual
Cue point
time code
(manual
End
recording
Start
recording
Rec IN
(automatic
recording)
recording)
recording)
Scene 1
Take 1
Scene 2
Take 2
Mark OUT
(manual
recording)
Mark IN
(manual
recording)
Mark IN
(manual
recording)
Mark OUT
(manual
recording)
ClipLink Guide
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Time codes recorded for Mark IN/OUT points
There is a gap between actual time codes and Mark IN/
OUT time codes recorded in the cassette memory, as
shown in the figure below. The time code value is rounded
up at each Mark IN point and rounded down at each Mark
OUT point, to a whole number of seconds.
Mark IN
(or Rec IN)
Mark OUT
(or Rec OUT)
Cue
Actual time code
12:23:15:10
12:34:20:20
12:39:24:23
Rounded down
Rounded up
Time code
recorded in the
cassette memory
(The index
12:23:16
12:34:20:20
12:39:24
picture is the
image around
12:23:15:10.)
Recording capacity for Mark IN/OUT point
time codes and cue point time codes
When in MARK mode, up to 198 pairs of Mark IN and
Mark OUT points can be recorded (if using a cassette with
16 Kbits of cassette memory).
When in CUE mode, up to 396 time code points (including
all cue point time codes and all Mark (Rec) IN and Mark
(Rec) OUT point time codes) can be recorded (if using a
cassette with 16 Kbits of cassette memory).
ClipLink Guide
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
A/B roll editing
Drop frame mode
Non-drop frame mode
An editing method that uses two or
more playback VCRs to create
special effects such as dissolve and
wipe, and uses one record VCR to
record the results of the editing.
Using an editing control unit allows
efficient control of the VCRs and
very precise editing.
Time code runs at 30 frames/sec. The
NTSC system, however, runs at
about 29.97 frames/sec. Drop frame
mode adjusts this difference. The
time code and video are synchronized
by dropping the first two frames of
the time code every minute, except at
the ten-minute marks.
The number of frames of the time
code and video run is not adjusted.
When you use the time code in non-
drop frame mode, the real playback
time will be about 86 seconds shorter
per day than the time code. If you edit
frame by frame or if you determine
the length of a shot by counting the
time code, use drop frame mode.
AES/EBU format
EE mode
A unified format for digital audio
signals. It allows a single connector
to carry the signals for two channels.
EE is an abbreviation of “Electric to
Electric”. Video and audio signalsare
supplied to the VCR’s internal
circuits, but not to the recording
heads.
Non-linear editing
Editing while playing back video and
audio signals recorded on hard disks.
Video scenes stored on disk can be
cued up quickly, for increased editing
editing.”
B–Y signal
A chrominance signal determined by
subtracting the Y (luminance) signal
from the B (blue) signal. One of the
component signals.
Head drum
A metal cylinder to which a video
head is attached. This drum is rotated
at high speeds in synchronization
with the sync signal during recording
and playback.
PCM audio
This is an audio signal represented by
pulse code modulation. The analog
audio signal is first broken down into
a sequence of pulses, and these are
then represented digitally.
Capstan
A drive mechanism that moves the
tape at a specified speed. Its rotation
normally synchronizes with a
reference sync signal.
Linear editing
Editing while playing back video and
audio signals recorded on video tape.
Preroll
Chrominance signal
Running of a video tape to a prior to
an edit-start point to enable the tape
to reach a steady speed and to be
synchronized with other video tapes.
Color signal containing color
information such as hue and
saturation. Also called C signal.
Loading
When being loaded, the tape is pulled
out of the cassette case and threaded
along the specified tape path and
wrapped round the drum to be ready
for recording or playback. Generally,
this is done automatically when you
place the cassette at the cassette
entrance of the VCR. Also called
threading.
Component signals (YRB)
A video signal consisting of a
luminance signal (Y) and two
chrominance signals (R−Y, B−Y).
R–Y signal
A chrominance signal determined by
subtracting the Y (luminance) signal
from the R (red) signal. One of the
component signals.
Composite signal
A composite video signal containing
video, burst and sync signals.
Reference video signal
A video signal consisting of a sync
signal or sync and burst signals, used
as a reference.
Loop-through connection
A connection which allows a signal
input to an input connector to pass
through the unit and exit from an
output connector as input to external
equipment. Also called bridging
connection.
Condensation
Condensation of moisture on the tape
transport mechanisms of VCRs
including the head drum. If moisture
condenses on the head drum, the tape
adheres to the drum and causes
malfunction.
Setup (for DSR-1500A)
The difference between the reference
black level and the blanking level of
a composite signal.
SMPTE
Luminance signal
Abbreviation of Society of Motion
Picture and Television Engineers, a
professional association established
in the USA.
The signal that determines the
brightness of the picture. Also called
Y signal. One of the component
signals.
Glossary
118
Download from Www.Somanuals.com. All Manuals Search And Download.
S/N
Superimpose
Abbreviation of Signal-to-Noise
(ratio). The higher the S/N value, the
less noise and higher the picture
quality.
To put a set of characters onto a
picture so that both can be seen at the
same time.
S-video
Search mode
A signal format in which Y
(luminance) and C (chrominance)
signals are separated to reduce
interference between them so that
noiseless images are reproduced.
A VCR operating mode used when
searching for specific scenes, by
viewing the videooutput or time code
values while playing back the tape at
various speeds in forward or reverse
direction.
Sync signal
A reference signal consisting of
vertical and horizontal sync signals
used for synchronizing the scanning
patterns of the video camera and the
monitor.
Servo lock
Synchronizing the drum rotation
phase and tape transport phase with a
reference signal during playback and
recording so that the video heads scan
the tape in the same pattern during
playback and recording.
TBC
Abbreviation of Time Base
Corrector. Electronic circuits to
electrically stabilize the playback
signals by removing color variation
and roll in the playback picture
caused by irregularity in drum
rotation and tape movement. Time
base correction reduces deterioration
of picture quality when transmitting
or copying playback signals.
Standby Off mode
One of two conditions in the stop
mode. The drum does not rotate and
tape is slackened. There is no damage
to the video heads and the tape, but
the VCR is not ready for immediate
recording or playback.
Standby On mode
One of two conditions in the stop
mode. The drum is rotating and the
tape is wrapped round the drum. The
VCR is ready for recording or
playback, so a still picture can be
obtained.
Threading
Time code
Signals recorded on the tape to
supply information on tape position
such as the hour, minute, second and
frame, to assist in setting edit points
or searching for particular scenes.
Subcarrier
A sine wave imposed on the
luminance portion of a video signal
and modulated to carry color
information. Its amplitude represents
color saturation and its phase
represents hue.
Unloading
When the EJECT button is pressed,
the VCR automatically winds the
tape back into the cassette case. Also
called “Unthreading.”
User bits
Sections of time code information
consisting of a total of 32 bits that can
be used for recording information
such as date, tape ID number,
program ID number, etc.
Glossary
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
120
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Index
Numerics
C
A
AES/EBU
E
Editing
Analog
F
digital non-linear editing system
video/audio signal input section
video/audio signal output section
H
High-speed
Audio
input/output level control section
I
AUDIO (AES/EBU)
AUDIO OUT 1/3 and 2/4 connectors
D
Digital
J
Index
121
Download from Www.Somanuals.com. All Manuals Search And Download.
L
M
OPERATIONAL FUNCTION
R
Recording/playback tape format
REMOTE
Remote
T
Tape
MONITOR
Monitor
N
Time data
O
S
P
PHONES
SDI/SDTI (QSDI)
U
Index
122
Download from Www.Somanuals.com. All Manuals Search And Download.
V
VIDEO
Video
VITC
W
Y
Index
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
http://www.sony.net/
Download from Www.Somanuals.com. All Manuals Search And Download.
|