4-187-302-11(1)
Blu-ray Disc/DVD
Home Theatre System
Operating Instructions
BDV-HZ970W / IZ1000W
©2010 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
13) Unplug this apparatus during
lightning storms or when
Important Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can
be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
unused for long periods of time.
14) Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed to
rain or moisture, does not
operate normally, or has been
dropped.
4) Follow all instructions.
5) Do not use this apparatus near
water.
6) Clean only with dry cloth.
7) Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
8) Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety
purpose of the polarized or
grounding-type plug. A
For the customers in
Canada
To reduce the risk of fire or electric
shock, do not expose this apparatus
to dripping or splashing, and do not
place objects filled with liquids,
such as vases, on the apparatus.
polarized plug has two blades
with one wider than the other. A
grounding type plug has two
blades and a third grounding
prong. The wide blade or the
third prong are provided for
your safety. If the provided
plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete
outlet.
For the wireless
transceiver (EZW-
RT10/EZW-RT10A)
(For the customers in
the U.S.A.)
– Reorient or relocate the receiving
antenna (aerial).
– Increase the separation between
the equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
This equipment must not be co-
located or operated in conjunction
with any other antenna or
transmitter.
10) Protect the power cord from
being walked on or pinched
particularly at plugs,
– Consult the dealer or an
experienced radio/TV technician
for help.
This equipment complies with FCC
radiation exposure limits set forth
for uncontrolled equipment and
meets the FCC radio frequency
(RF) Exposure Guidelines in
Supplement C to OET65.
convenience receptacles, and
the point where they exit from
the apparatus.
CAUTION
You are cautioned that any changes
or modifications not expressly
approved in this manual could void
your authority to operate this
equipment.
11) Only use attachments/
accessories specified by the
manufacturer.
This equipment should be installed
and operated with at least 20cm and
more between the radiator and
person’s body (excluding
extremities: hands, wrists, feet and
ankles).
12) Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use caution
when moving the cart/
apparatus combination to avoid
injury from tip-over.
The shielded interface cable
recommended in this manual must
be used with this equipment in
order to comply with The limits for
a digital device pursuant to Subpart
B of Part 15 of FCC Rules.
US
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5650-5850 MHz and these radars
could cause interference and/or
damage to this device.
For the wireless
transceiver (EZW-
RT10/EZW-RT10A)
(For the customers in
Canada)
Copyrights and
Trademarks
• This product incorporates
copyright protection technology
that is protected by U.S. patents
and other intellectual property
rights.
This device uses 5 GHz band for
wireless LAN communication and
the maximum gain of the antenna in
this device is 5 dBi.
This Class B digital apparatus
This equipment complies with
FCC/IC radiation exposure limits
set forth for an uncontrolled
environment. This equipment
should be installed and operated
with minimum distance 20 cm
between the radiator and your body
(excluding extremities: hands,
wrists and feet).
complies with Canadian ICES-003.
Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for
home and other limited viewing
uses only unless otherwise
authorized by Macrovision.
Reverse engineering or
disassembly is prohibited.
• This system incorporates with
Dolby* Digital and Dolby Pro
Logic (II) adaptive matrix
surround decoder and the DTS**
Digital Surround System.
* Manufacturedunder license
from Dolby Laboratories.
Dolby, Pro Logic, and the
double-D symbol are
This device complies with RSS-
Gen of IC Rules.
Operation is subject to the
following two conditions:
(1) this device may not cause
interference, and (2) this device
must accept any interference,
including interference that may
cause undesired operation of this
device.
This device and its antenna(s) must
not be co-located or operating with
any other antenna or transmitter
except Grant condition.
This equipment complies with IC
radiation exposure limits set forth
for uncontrolled equipment and
meets RSS-102 of the IC radio
frequency (RF) Exposure rules.
This equipment should be installed
and operated with at least 20cm and
more between the radiator and
persons body (excluding
If you have any questions about this
product, contact Sony Customer
Information Service Center at 1-
800-222-7669 or visit http://
trademarks of Dolby
Laboratories.
**Manufacturedunder license
under U.S. Patent #’s:
5,451,942; 5,956,674;
5,974,380; 5,978,762;
6,226,616; 6,487,535;
The telephone number below is for
FCC-related matters only.
extremities: hands, wrists, feet and
ankles).
Regulatory Information
7,212,872; 7,333,929;
For the USB Wireless
LAN Adapter (UWA-
BR100)
Pursuant to FCC regulations, you
are cautioned that any changes or
modifications not expressly
approved in this manual could void
your authority to operate this
equipment.
7,392,195; 7,272,567 &
other U.S. and worldwide
patents issued & pending.
DTS is a registered
trademark and the DTS
logos, Symbol, DTS-HD
and DTS-HD Master Audio
are trademarks of DTS, Inc.
© 1996-2008 DTS, Inc. All
Rights Reserved.
Declaration of Conformity
Trade Name: SONY
Model: UWA-BR100
Responsible Party: Sony
Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone Number: 858-942-
2230
To prevent radio interference to the
licensed service, this device is
intended to be operated indoors and
away from windows to provide
maximum shielding. Equipment (or
its transmit antenna) that is
installed outdoors is subject to
licensing.
• This system incorporates High-
Definition Multimedia Interface
(HDMITM) technology.
HDMI, the HDMI logo and High-
Definition Multimedia Interface
are trademarks or registered
trademarks of HDMI Licensing
LLC.
This device complies with part
15 of the FCC rules. Operation is
subject to the following two
conditions: (1) This device may
not cause harmful interference,
and (2) this device must accept
any interference received,
Only use Wireless LAN indoors
when using it with IEEE 802.11a
(5 GHz).
including interference that may
cause undesired operation.
• Java and all Java-based
trademarks and logos are
trademarks or registered
trademarks of Sun Microsystems,
Inc.
High power radars are allocated as
primary users (meaning they have
priority) of 5250-5350 MHz and
US
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• “BD-LIVE” and
Gracenote in the United States
and/or other countries.
“BONUSVIEW” are trademarks
of Blu-ray Disc Association.
• “Blu-ray Disc” is a trademark.
• “Blu-ray Disc,” “DVD+RW,”
“DVD-RW,” “DVD+R,” “DVD-
R,” “DVD VIDEO,” and “CD”
logos are trademarks.
About These
Operating
Instructions
• “PhotoTV HD” and the “PhotoTV
HD” logo are trademarks of Sony
Corporation.
• The instructions in these
Operating Instructions
describe the controls on the
remote. You can also use the
controls on the unit if they
have the same or similar
names as those on the remote.
• In this manual, “disc” is used
as a general reference for
BDs, DVDs, Super Audio
CDs, or CDs unless otherwise
specified by the text or
illustrations.
• The instructions in this
manual are for BDV-
HZ970W and BDV-
IZ1000W. BDV-HZ970W is
the model used for
illustration purposes. Any
difference in operation is
clearly indicated in the text,
for example, “BDV-
HZ970W.”
• The items displayed on the
TV screen may vary
depending on the area.
• The default setting is
underlined.
• The system is compatible
with the S-AIR function,
which allows transmission of
sound between S-AIR
• “Blu-ray 3D” and “Blu-ray 3D”
logo are trademarks of Blu-ray
Disc Association.
• MPEG Layer-3 audio coding
technology and patents licensed
from Fraunhofer IIS and
Thomson.
• “BRAVIA” is a trademark of
Sony Corporation.
• “AVCHD” and the “AVCHD”
logo are trademarks of Matsushita
Electric Industrial Co., Ltd. and
Sony Corporation.
• iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries.
• “Made for iPod” means that an
electronic accessory has been
designed to connect specifically
to iPod and has been certified by
the developer to meet Apple
performance standards.
• “S-AIR” and its logo are
trademarks of Sony Corporation.
•
, “XMB,” and “xross media
bar” are trademarks of Sony
Corporation and Sony Computer
Entertainment Inc.
• Apple is not responsible for the
operation of this device or its
compliance with safety and
regulatory standards.
• “PLAYSTATION” isa trademark
of Sony Computer Entertainment
Inc.
®
®
• DivX , DivX Certified and
associated logos are registered
trademarks of DivX, Inc. and are
used under license. (Except for
U.S. models.)
• Windows Media is either a
registered trademark or trademark
of Microsoft Corporation in the
United States and/or other
countries.
®
• Music and video recognition
technology and related data are
• DLNA , the DLNA Logo and
DLNA CERTIFIED™ are
trademarks, service marks, or
certification marks of the Digital
Living Network Alliance.
®
provided by Gracenote .
Gracenote is the industry standard
in music recognition technology
and related content delivery. For
more information, please visit
CD, DVD, Blu-ray Disc, and
music and video-related data from
Gracenote, Inc., copyright ©
2000-present Gracenote.
Gracenote Software, copyright ©
2000-present Gracenote. One or
more patents owned by Gracenote
apply to this product and service.
See the Gracenote website for a
nonexhaustive list of applicable
Gracenote patents. Gracenote,
CDDB, MusicID, MediaVOCS,
the Gracenote logo and logotype,
and the “Powered by Gracenote”
logo are either registered
• Other system and product names
are generally trademarks or
registered trademarks of the
manufacturers. ™ and ® marks
are not indicated in this document.
products wirelessly. For
details on the S-AIR function,
• Notes or instructions for the
surround amplifier, surround
back amplifier, or S-AIR
receiver in these Operating
Instructions refer only to
when the surround amplifier,
surround back amplifier, or
S-AIR receiver is used.
trademarks or trademarks of
US
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Deactivating the Buttons on
the Unit........................................... 55
Controlling Your TV or Other
Remote ........................................... 56
Step 3: Connecting to the
Network....................................28
Step 4: Setting up the
S-AIR Wireless System...........29
Step 5: Performing the Easy
Step 7: Enjoying Surround
Selecting the Effect to Suit
the Source .......................................41
Selecting the Audio Format, Multilingual
Tracks, or Channel..........................41
Enjoying Multiplex Broadcast
Sound..............................................42
Using the Control for HDMI Function for
“BRAVIA” Sync ............................50
Calibrating the Appropriate Settings
Automatically .................................52
US
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
BDV-HZ970W
• Main unit (1)
• Posts for the front speakers
(long) (2)
• Calibration mic (1)
• Surround amplifier (1)
• Posts for the front speakers
(short) (2)
• Front speakers (2)
• Screws for the front speakers
(8)
• Wireless transceivers (2)
• USB Wireless LAN Adapter
(UWA-BR100)
• FM wire antenna (aerial) (1)
• Surround speakers (2)
• Speaker cords (6, white/red/
blue/gray/green/purple)
• UWA-BR100 External
cable
• Center speaker (1)
• Subwoofer (1)
• Video cord (1)
• Operating Instructions
• Speaker Installation Guide
• Quick Setup Guide
• Remote commander
(remote) (1)
• End user license agreement
• Easy Setup Disc (DVD)
• R6 (size AA) batteries (2)
• Bases for the front speakers (2)
US
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BDV-IZ1000W
• Main unit (1)
• Bases for the front speaker
stands (2)
• Remote commander
(remote) (1)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• Bases for the surround
speakers (2)
• Front and surround speakers
(4)
• Base adapters for the surround
speakers (2)
• Surround amplifier (1)
• Wireless transceivers (2)
• Screws (with washer) for the
front speakers (4)
• Center speaker (1)
• Subwoofer (1)
• Screws for the front speakers/
surround speakers (4)
• Operating Instructions
• Speaker Installation Guide
• Quick Setup Guide
• FM wire antenna (aerial) (1)
• End user license agreement
• Front speaker stands (2)
• Speaker cords (6, white/red/
blue/gray/green/purple)
• Video cord (1)
US
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment.
US
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
Front panel
FUNCTION
VOLUME
PUSH OPEN
A "/1 (on/standby)
C
(remote sensor)
Turns on the unit, or sets it to standby mode.
B Play operation buttons
D Front panel display
N (play)
F
(USB) port (page 36)
Starts or re-starts playback (resume play).
Plays a slideshow when a disc containing
JPEG image files is inserted.
Used for connecting a USB device.
x (stop)
Stops playback and remembers the stop
point (resume point).
The resume point for a title/track is the last
point you played or the last photo for a
photo folder.
FUNCTION
Selects the playback source.
VOLUME +/–
Adjusts the system’s volume.
Opens or closes the disc tray.
US
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
About the indications in the front panel display
A Displays the current sound format.
I S-AIR indicator (only when the wireless
transceiver is inserted into the unit)
B Lights up when outputting 1920 ×
1080p/24 Hz video signals.
Lights up during wireless
transmission. When [Standby] is set to
[On], flashes when the main unit is in
standby mode and wireless
transmission between the main unit
and S-AIR receiver is not activated.
C Lights up while virtual 7.1ch decoding
is activated.
D Lights up when outputting 720p/1080i/
1080p video signals from the HDMI
(OUT) jack or 720p/1080i video signals
from the COMPONENT VIDEO OUT
jacks.
J Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, surround setting, etc.
E Lights up when the HDMI (OUT) jack is
correctly connected to an HDCP (High-
bandwidth Digital Content Protection)-
compliant device with HDMI or DVI
(Digital Visual Interface) input.
K Lights up when repeat play is
activated.
L Displays system’s playing status.
F Lights up when a radio station is
received. (Radio only) (page 44)
M Lights up when muting is on.
G Lights up when stereo sound is
received. (Radio only) (page 44)
H Flashes when the sleep timer is set.
(page 55)
US
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
LAN(100)
HDMI
IN
ARC
S-AIR ID
IN
1
2
OUT
A
B
C
EZW-RT10
AUDIO
AUDIO IN
L
ANTENNA
75 COAXIAL
FM
DIGITAL IN
SPEAKERS
FRONT WOOFER CENTER
SAT/CABLE
TV
A.CAL
MIC
VIDEO COMPONENT VIDEO OUT
OUT B/CB R/CR
Y
P
P
FRONT
R
L
COAX
OPT
ECM-AC2
R
A Wireless transceiver (EZW-RT10) slot
H COMPONENT VIDEO OUT jacks (page
(page 27)
F ANTENNA (75Ω COAXIAL FM) jack
M DIGITAL IN (SAT/CABLE COAX) jack
(page 26)
(page 24)
G
US
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround amplifier
Rear panel
Front panel
SURROUND SELECTOR
L
R
IMPEDANCE USE
3-16
A
B
C
PAIRING
SURROUND SURROUND BACK
S-AIR ID
SPEAKERS
EZW-RT10
S-AIR/STANDBY
A "/1 (Power)
Indicator
Status
Turns the surround amplifier on/off.
Turns off.
The surround amplifier is
turned off.
B S-AIR/STANDBY indicator
You can check the status of wireless
transmission of surround speaker audio
signals between the main unit and surround
amplifier.
Flashes orange. The wireless transceiver is not
inserted/not fully inserted/
inserted upside-down into the
wireless transceiver slot.
Flashes red.
The surround amplifier’s
protection is active.
Indicator
Status
Turns green.
Wirelesstransmission between
the main unit and the surround
amplifier is established
C S-AIR ID switch
Selects the S-AIR ID.
correctly and the main unit is
transmitting audio signals to
the surround speakers via the
surround amplifier.
D PAIRING button
Starts pairing.
E PAIRING indicator
Indicates the pairing status.
Flashes green Wirelesstransmission between
quickly.
the main unit and the surround
amplifier is established
correctly, but audio signals to
the surround speakers are not
being transmitted by the main
unit.
F SURROUND SELECTOR switch
Selects the mode for the surround amplifier.
G SPEAKERS jacks
H Wireless transceiver (EZW-RT10) slot
Flashes green Wirelesstransmission between
slowly.
the main unit and the surround
amplifier is not set up
correctly.
Turns red.
Wirelesstransmission between
the main unit and the surround
amplifier is not set up, or either
the surround amplifier or the
whole system is in standby
mode.
US
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Turns on the system or sets it to standby
mode.
The buttons for system operation only are
described below. See “Controlling Your TV or
(page 56) for the buttons for operation of the
connected components.
Changes the component to be operated on
the remote.
STB: You can operate a cable box, digital
satellite receiver, digital video receiver, etc.
TV: You can operate a TV.
BD: You can operate this Blu-ray Disc/
DVD Home Theatre System.
wh
ONE-TOUCH
PLAY
AV
THEATER
wg
wf
1
2
BRAVIA Sync
STB
Enters the title/chapter numbers, radio
frequencies, etc.
TV
BD
1
2
5
8
0
3
3
4
7
6
9
Enters the selected item.
wd
4
5
ENTER
CC
AUDIO SUBTITLE WIDE
TONE
INPUT
SLEEP
Adjusts the sound.
ws
wa
D.TUNING
YELLOW BLUE
RED
GREEN
6
7
Sets the sleep timer.
G FAVORITES
w;
8
9
Displays the contents of Internet entries
added to the Favorites List. You can save 18
favorite Internet contents.
0
qa
ql
qk
PAGE
PAGE
H POP UP/MENU
FUNCTION
SOUND MODE
qs
Opens or closes the BD-ROM’s Pop-up
Menu, or the DVD’s menu.
PRESET
TUNING
REC
REPLAY ADVANCE PRESET
PLAY
TUNING
STOP
I C/X/x/c
qd
PAUSE
Moves the highlight to a displayed item.
VOL
CH
DISPLAY
(ENTER)
Enters the selected item.
qj
qh
qf
qg
MUTING
SYSTEM
MENU
Displays the options menu on the TV
screen.
JUMP
• Number 5, AUDIO, CH +, and N buttons
have a tactile dot. Use the tactile dot as a
reference when operating the remote.
• Names of buttons that work after pressing the
TV or STB operation mode buttons are
indicated with yellow label.
Enters or exits the system’s home menu.
Selects the sound mode.
US
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M Playback operation buttons
Adjusts the volume.
./> (previous/next)
Skip to the previous/next chapter, track, or
file.
Selects the playback source.
S RETURN
REPLAY/ADVANCE
Briefly replay the current scenes for 10
seconds./Briefly fast forwards the current
scenes for 15 seconds.
Returns to the previous display.
T TOP MENU
Opens or closes the BD’s or DVD’s Top
Menu.
m/M (fast reverse/fast forward)
Fast reverse/fast forward the disc during
playback. Each time you press the button,
search speed changes.
U Color buttons (YELLOW/BLUE/RED/
GREEN)
Shortcut keys for selecting items on some
Blu-ray menus (can also be used for Java
interactive operations on BDs).
Activates slow-motion play when pressed
for more than one second in pause mode.
Plays one frame at a time when pressed in
pause mode.
Selects the audio format/track.
N PLAY
Selects the subtitle language when
multilingual subtitles are recorded on a BD-
ROM/DVD VIDEO.
Starts or re-starts playback (resume play).
Plays a slideshow when a disc containing
JPEG image files is inserted.
D.TUNING (Direct Tuning) (page 44)
Tunes in to the desired radio frequency.
X PAUSE
Pauses or re-starts playback.
x STOP
Opens or closes the disc tray.
Stops playback and remembers the stop
point (resume point). The resume point for
a title/track is the last point you played or
the last photo for a photo folder.
Switches to the optimum video mode for
watching movies automatically.
Radio operation buttons
Activates One-Touch Play.
PRESET +/–
TUNING +/–
Displays the playback information on the
TV screen.
Displays stream information in the front
panel display when: 1 The function is set
to “TV”/“SAT/CABLE”/“HDMI1”/
“HDMI2,” and 2 Digital signals are input
via the DIGITAL IN/HDMI (IN 1)/HDMI
(IN 2) jack.
Enters the system menu.
P MUTING
Turns off the sound temporarily.
US
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Step 1: Installing the System
Positioning the speakers
For the best possible surround sound, place all speakers at the same distance from the listening position
(A). The distance can be between 0 to 23 feet (0.0 to 7.0 meters).
If you cannot place the center speaker and surround speakers at the same distance as (A), place them
within 23 feet (7.0 meters) of the listening position.
Place the surround speakers to the rear of the listening position (B).
The subwoofer can be placed anywhere in the room.
Center speaker
Subwoofer
Front left speaker (L)
Front right speaker (R)
A
A
A
30
30
B
45
45
B
A
A
Surround left speaker (L)
Surround right speaker (R)
Note
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,
oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not lean or hang on a speaker, as it may fall down.
US
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To add the optional surround back speakers
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP2,
optional). The optional product lineup differs depending on the area.
For the position of the surround back speakers, refer the illustration below (C).
Center speaker
Subwoofer
Front left speaker (L)
Front right speaker (R)
Surround left
speaker (L)
Surround right
speaker (R)
30 30
45
45
C
C
Surround back left speaker (L)
(optional)
Surround back right speaker (R)
(optional)
Note
• To use the surround back speakers, set [Surround Back] (page 54) in [Speaker Settings] to [Yes] while performing
US
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the speakers
For assembling the speakers, refer to “Speaker Installation Guide” (supplement).
To connect speaker cords to the center speaker and subwoofer (BDV-
IZ1000W only)
Speaker terminals are located on the rear of the speakers.
Connector
Colored tube
(+)
(–)
Rear of the subwoofer
Purple colored tube
Rear of the center speaker
Green colored tube
When installing the speakers on a wall
Caution
• Contact a screw shop or installer regarding the wall material or screws to be used.
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where
reinforcement is applied.
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or
improper screw installation, natural calamity, etc.
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the colored tube to 3, and the speaker cord without the colored tube to #.
Colored tube
Front left speaker (L): White
Front right speaker (R): Red
Center speaker: Green
Surround left speaker (L): Blue
Surround right speaker (R): Gray
US
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
Hole on the back of
4 mm (3/16 inch)
the speaker
5 mm
(7/32 inch)
30 mm (1 3
/16 inches)
10 mm
13
(
/32 inch)
Fasten the screws to the wall.
BDV-HZ970W
BDV-IZ1000W
For the center speaker
For the front speakers
219 mm
5
(8
/8 inches)
330 mm
13 inches)
(
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
For the center speaker
219 mm
5
(8
/8 inches)
For the other speakers
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch)
(
/
to
/
inch)
32
32
32
32
For the surround speakers
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
US
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Hang the speakers on the screws.
Hole on the back of
the speaker
5 mm
(7/32 inch)
10 mm
13
(
/32 inch)
Rear of the speaker
US
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other
connections are made.
Note
• When you connect another component with a volume control, turn down the volume of the other components to a
level where sound is not distorted.
Connecting the speakers
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker.
Connect the speaker cords to match the color of the SPEAKERS jacks of the unit.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #. Do not catch the speaker cord
insulation (rubber covering) in the speaker terminals.
To connect speaker cords to the unit and surround amplifier
When connecting to the unit and surround amplifier, insert the connector until it clicks.
Rear panel of the surround amplifier
Rear panel of the unit
White
(Front left speaker (L))
Gray
(Surround right speaker (R))
L
R
E
S
U
E
3-16
C
N
A
D
E
P
IM
S
R
E
K
A
E
P
S
CENTER
SPEAKERS F
ER
OO
W
T
L
ON
FR
NT
O
R
FR
Green
(Center speaker)
Purple
(Subwoofer)
Blue
(Surround left speaker (L))
Red
(Front right
speaker (R))
US
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Video connection)
This connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
Rear panel of the unit
C Video cord (supplied)
C
R
A
T
U
HDMI
O
2
IN
1
IN
A HDMI cable
(not supplied)
OUT
R/CR
P
B
COMPONENT/CVIDEO
B
P
Y
VIDEO
OUT
B Component video
cable (not supplied)
To the video input
jack of the TV.
To the component
video input jacks of
the TV.
To the HDMI IN jack
of the TV.
Method 1: HDMI cable (A) connection
If your TV has an HDMI jack, connect to the TV with an HDMI cable. Picture quality will be improved
compared to using the component video cable connection or the video cord connection.
Method 2: Component video cable (B) connection
If your TV does not have an HDMI jack, but has component video input jacks, connect to the TV with
a component video cable. Picture quality will be improved compared to using the video cord
connection.
When connecting with the component video cable, you need to select the type of output signal (page
60).
Method 3: Video cord (C) connection
If you do not have an HDMI cable or a component video cable, make this connection.
US
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Audio connection)
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system,
perform this connection.
Rear panel of the unit
IN
L
A
IT
IG
D
V
T
E
L
T
P
B
O
A
/C
T
A
S
X
A
O
C
Digital optical cord
(not supplied)
To the digital optical out jack of
the TV.
With a digital audio connection, the system receives a Dolby Digital multiplex broadcast signal and
you can enjoy multiplex broadcast sound.
Note
• When you connect the TV and the unit with an audio cord, see “Connecting the other components” (page 24).
About Audio Return Channel (ARC)
If your TV is compatible with the Audio Return Channel function, an HDMI cable connection also
sends a digital audio signal from the TV. You do not need to make a separate audio connection for
listening to TV sound. For details of the Audio Return Channel function, see [Audio Return Channel]
US
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the other components
When another component you wish to connect to the system has an
HDMI OUT jack
You can connect a component that has an HDMI OUT jack such as a set-top box/digital satellite
®
receiver or PLAYSTATION 3, etc., with an HDMI cable. An HDMI cable connection can send both
video and audio signals. By connecting the system and the component using an HDMI cable, you can
enjoy high-quality digital pictures and sound via the HDMI (IN 1) or HDMI (IN 2) jack.
Rear panel of the unit
C
R
A
T
U
HDMI
O
2
IN
1
IN
HDMI cable (not
supplied)
To the HDMI OUT jack of the set-top box/
digital satellite receiver or
PLAYSTATION®3, etc.
Note
• Video signals to the HDMI (IN 1/IN 2) jacks are output from the HDMI (OUT) jack only when the “HDMI1” or
“HDMI2” function is selected.
• To output an audio signal from the HDMI (OUT) jack, you need to change the audio output setting. For details, see
US
24
Download from Www.Somanuals.com. All Manuals Search And Download.
When the component does not have an HDMI OUT jack
Video signals from the system and the components are sent to the TV, and audio signals from the
components are sent to the system as follows.
TV
Signal flow
System
: Video signal
: Audio signal
You can enjoy connected components via the system’s speakers.
• VCR or digital satellite receiver, etc. (not supplied), which has a digital coaxial output jack: D
• VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): E
Rear panel of the unit
IO
D
U
A
IN
IO
D
U
A
L
IN
L
A
IT
IG
D
V
T
T
P
LE
B
O
A
/C
T
A
S
R
E Audio cord
X
A
O
C
(not supplied)
D Digital coaxial cord
(not supplied)
To the digital coaxial out jack
of the VCR or digital satellite
receiver, etc.
To the audio out jacks of the VCR,
digital satellite receiver, PlayStation,
or portable audio source, etc.
US
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the antenna (aerial)
Rear panel of the unit
A
IA
N
X
N
O
E
C
T
N
5
A
L
A
7
M
F
or
FM wire antenna (aerial)
(supplied)
Note
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Unit
Outdoor FM antenna (aerial)
ANTENNA
75 COAXIAL
FM
US
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the wireless transceiver
You can transmit the audio signal from the main unit to an S-AIR product, such as the surround
amplifier or S-AIR receiver.
To transmit sound from the unit, insert one wireless transceiver into the main unit and the other one
into the S-AIR product, e.g. the surround amplifier.
Rear panel of the surround amplifier
Rear panel of the unit
0
1
T
R
-
W
Z
E
Wireless
transceiver
Wireless
transceiver
Note
• Please make sure to fully insert the wireless transceiver into the wireless transceiver slot. You should hear a click
when the wireless transceiver is inserted correctly.
• To avoid inserting the wireless transceiver upside-down, orient it with the Sony logo facing up.
US
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Connecting to
the Network
Connecting the system to the Internet allows you
to watch Internet video, listen to Internet audio,
use BD-LIVE, and update the Home Theatre
System software.
LAN cable
(not supplied)
USB
Wireless
LAN
Adapter
ADSL modem/ Internet
cable modem
Wireless LAN
router
Wired Setup
Note
Use a LAN cable to connect to the LAN (100)
terminal on the unit.
• The placement distance between the USB Wireless
LAN Adapter and your wireless LAN router differs
depending on the usage environment. If the system
cannot connect to the network or the network
connection is unstable, move the USB Wireless LAN
Adapter to a different position or place the USB
Wireless LAN Adapter and the wireless LAN router
closer to each other.
LAN cable
(not supplied)
To set the network settings
Select [Network Settings], [Internet Settings],
follow the on-screen instructions to complete
the setup.
Internet
Broadband
router
ADSL modem/
cable modem
Tip
• Using a shielded LAN cable, straight or crossing, is
recommended.
Tip
• For details on wireless network setup, please visit:
To set the network settings
Select [Network Settings], [Internet Settings],
screen instructions to complete the setup.
About wireless LAN security
Since communication via the wireless LAN
function is established by radio waves, the
wireless signal may be susceptible to
interception. To protect wireless
USB Wireless Setup
communication, this system supports various
security functions. Be sure to correctly
configure the security settings in accordance
with your network environment.
Use a wireless LAN via the USB Wireless LAN
Adapter (Sony UWA-BR100* only) (supplied
with BDV-HZ970W).
The USB Wireless LAN Adapter may not be
available in some regions/countries.
* As of January 2010.
No Security
Although you can easily make settings, anyone
can intercept wireless communication or intrude
into your wireless network, even without any
sophisticated tools. Keep in mind that there is a
risk of unauthorized access or interception of
data.
Turn the unit off before connecting the
extension cable or inserting the USB Wireless
LAN Adapter. After inserting the USB Wireless
LAN Adapter to the base of the extension cable
and connecting the extension cable to the
(USB) port (front or rear), turn the unit on again.
US
28
Download from Www.Somanuals.com. All Manuals Search And Download.
WEP
WEP applies security to communications to
prevent outsiders from intercepting
communications or intruding into your wireless
network. WEP is a legacy security technology
that enables older devices, which do not support
TKIP/AES, to be connected.
Step 4: Setting up the
S-AIR Wireless System
Before performing Step 4
Make sure all connections are secure, and then
connect the AC power cords (mains leads).
To use the S-AIR wireless system, you need to
set up the surround amplifier.
The unit transmits sound to the surround
amplifier that is connected to the surround
speakers. To activate wireless transmission,
perform the following Steps.
WPA-PSK (TKIP), WPA2-PSK (TKIP)
TKIP is a security technology developed to
correct for the deficiencies of WEP. TKIP
assures a higher security level than WEP.
WPA-PSK (AES), WPA2-PSK (AES)
AES is a security technology that uses an
advanced security method that is distinct from
WEP and TKIP.
AES assures a higher security level than WEP or
TKIP.
1
Press "/1 to turn the system on.
"/1
Make sure that “S-AIR” light up in the front
panel display. When “S-AIR” does not light
up, make sure that the wireless transceiver
is inserted into the unit correctly.
2
3
Set the SURROUND SELECTOR switch
of the surround amplifier to
SURROUND.
SURROUND SELECTOR
SURROUND SURROUND BACK
SURROUND SELECTOR
SURROUND SURROUND BACK
Set the S-AIR ID switch of the surround
amplifier to A.
A
B
C
PAIRING
S-AIR ID
A
B
C
S-AIR ID
US
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press "/1 to turn the surround amplifier
on.
Step 5: Performing the
Easy Setup
When wireless transmission is activated,
the S-AIR/STANDBY indicator turns
green.
Follow the Steps below to make the basic
adjustments for using the system.
Displayed items vary depending on the country
model.
S-AIR/STANDBY indicator
S-AIR/STANDBY
Note
• To use the optional surround back speakers, set
[Surround Back] in [Speaker Settings] to [Yes]
"/1
If the S-AIR/STANDBY indicator does not
turn green, see “Surround amplifier”
"/1
For details of the S-AIR function, see
1
4
7
2
5
8
0
3
6
9
About the standby mode
The surround amplifier enters standby mode
automatically (the S-AIR/STANDBY indicator
turns red) when the main unit is in standby mode
or wireless transmission is deactivated.
The surround amplifier turns on automatically
(the S-AIR/STANDBY indicator turns green)
when the system is turned on and wireless
transmission is activated.
C/X/x/c,
HOME
1
2
Turn on the TV.
Connect the calibration mic to the
A.CAL MIC jack on the rear panel.
Set up the calibration mic at ear level using
a tripod, etc. (not supplied). The front of
each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic.
US
30
Download from Www.Somanuals.com. All Manuals Search And Download.
To recall the Easy Setup Display
1
Press HOME.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Easy Setup], then
press
[Setup].
L
A
.C
A
IC
M
2
C
-A
M
C
E
.
4
Press C/c to select [Start], then press
.
The Easy Setup Display appears.
Calibration mic
3
4
Press [/1 on the unit, and [/1 on the
surround amplifier.
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
The Easy Setup Display for OSD language
selection appears.
Easy Setup - OSD
Select the language to be displayed by this unit.
English
Français
Español
Português
5
Perform the [Easy Setup]. Follow the
on-screen instructions to make the
basic settings using C/X/x/c, and
.
For details about [Auto Calibration]
settings in [Easy Setup], see “Calibrating
US
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Function
Source
Step 6: Selecting the
Source
“SAT/CABLE” Component that is connected to
the DIGITAL IN (SAT/CABLE
COAX) jack on the rear panel
You can select the playback source.
“AUDIO”
Component that is connected to
the AUDIO (AUDIO IN L/R)
jacks on the rear panel (page 24)
1
4
7
2
5
8
0
3
6
9
FUNCTION
Press FUNCTION repeatedly until the
desired function appears in the front panel
display.
Each time you press FUNCTION, the function
changes as follows.
“BD/DVD” t “D. MEDIA” t “TUNER FM”
t “HDMI1” t “HDMI2” t “TV” t
“SAT/CABLE” t “AUDIO” t “BD/DVD”
t …
Function
Source
“BD/DVD”
“D. MEDIA”
Disc that is played by the system
USB device, iPod, BRAVIA
Internet Video, or DLNA server
“TUNER FM”
FM radio (page 44)
“HDMI1”/
“HDMI2”
Component that is connected to
the HDMI (IN 1) or HDMI (IN 2)
jack on the rear panel (page 24)
“TV”
Component (TV, etc.) that is
connected to the DIGITAL IN
(TV OPT) jack on the rear panel,
or a TV compatible with the Audio
Return Channel function that is
connected to the HDMI (OUT)
US
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7: Enjoying Surround Sound
After performing the previous Steps and starting playback, you can easily enjoy surround sound. You
can also select pre-programmed surround settings that are tailored to different kinds of sound sources.
They bring the exciting and powerful sound of movie theaters into your home.
1
4
7
2
5
8
0
3
6
9
X/x/c,
SYSTEM MENU
Selecting surround settings based on your listening preference
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “SUR.SETTING” appears in the front panel display, then
press
or c.
3
Press X/x repeatedly until the surround setting you want appears in the front panel
display.
See the table below for surround sound setting descriptions.
4
5
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
About speaker output of each surround setting
The table below describes the options when you connect all the speakers to the unit.
The default setting is “A.F.D. 7.1CH.”
Sound from
Surround setting
Effect
Depending on the source.
“A.F.D. STD”
(AUTO FORMAT
The system discriminates the sound format of the source and
presents sound as it was recorded/encoded.
DIRECT STANDARD)
US
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound from
Surround setting
Effect
“A.F.D. 7.1CH”
(AUTO FORMAT
DIRECT 7.1CH)
• 2 channel source: The system simulates surround sound
from 2 channel sources and outputs sound from the 5.1
channel speakers by duplicating 2 channel source sound
across each speaker.
• Multi-channel source: The system creates the surround back
sound virtually depending on the number of channels of the
source and outputs the sound as 7.1 channel surround sound.
“PRO LOGIC”
“PLII MOVIE”
“PLII MUSIC”
• 2 channel source: The system simulates surround sound
from 2 channel sources and outputs sound from the 5.1
channel speakers.
– “PRO LOGIC” performs Dolby Pro Logic decoding.
– “PLII MOVIE” performs Dolby Pro Logic II movie
mode decoding.
– “PLII MUSIC” performs Dolby Pro Logic II music mode
decoding.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source.
“NEO6 CIN”
“NEO6 MUS”
• 2 channel source: The system simulates surround sound
from 2 channel sources and produces 6.1 channel sound.
– “NEO6 CIN” performs DTS Neo:6 Cinema mode
decoding.
– “NEO6 MUS” performs DTS Neo:6 Music mode
decoding.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source.
“2CH STEREO”
The system outputs the sound from the front speakers and
subwoofer regardless of sound format or number of channels.
Multi-channel surround formats are downmixed to 2
channels.
Note
• When you select “A.F.D. 7.1CH,” depending on the disc or source, the beginning of the sound may be cut off while
the optimum mode is automatically selected. To avoid cutting the sound, select “A.F.D. STD.”
• When bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• Depending on the input stream, the surround settings may not be effective.
• When changing the surround setting while using the S-AIR receiver, sound from the S-AIR receiver may skip.
• When you play a Super Audio CD, surround settings are not activated.
Tip
• The system memorizes the last surround setting selected for each function.
Whenever you select a function such as “BD/DVD” or “TUNER FM,” the surround setting that was last applied to
the function is automatically applied again. For example, if you select “BD/DVD” with “PRO LOGIC” as the
surround setting, then change to another function, and then return to “BD/DVD,” “PRO LOGIC” will be applied
again.
US
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• Delete unnecessary data in internal memory or USB
Playback
memory. Select [Erase BD Data] in
[Video] to
delete unnecessary data. If you use USB memory as
local storage, all saved data in the [BUDA/BUDB]
folder is deleted. Make sure to backup any video/
music/photo data in the [BUDA/BUDB] folder.
Playing a Disc
For playable discs, see “Playable Discs”
Enjoying Blu-ray 3D
1
2
Switch the input selector on your TV so
that the signal from the system
appears on your TV screen.
You can enjoy Blu-ray 3D Discs with the 3D
logo*.
Press Z, and place a disc on the disc
tray.
*
1
Prepare for Blu-ray 3D Disc playback.
• Connect the system to your 3D-
compatible TV using a High-Speed
HDMI cable (not supplied).
• Set [3D Output Setting] and [TV Screen
Size Setting for 3D] in [Screen Settings]
2
Insert a Blu-ray 3D Disc.
The operation method differs depending on
the disc. Refer to the operating instructions
supplied with the disc.
3
Press Z to close the disc tray.
appears on the home menu and playback
starts.
Tip
If playback does not start automatically,
• Refer also to the operating instructions of your 3D-
compatible TV.
select
in the
[Video],
[Music], or
.
[Photo] category, and press
Enjoying BONUSVIEW/BD-LIVE
Some BD-ROMs with “BD-LIVE” Logo* have
bonus content and other data that can be
downloaded for enjoyment.
*
1
2
Prepare for BONUSVIEW/BD-LIVE.
• Set [BD Internet Connection] to [Allow]
Insert a BD-ROM with BONUSVIEW/
BD-LIVE.
The operation method differs depending on
the disc. Refer to the operating instructions
of the disc.
US
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the play information
Playing from a USB
Device
You can check the playback information, etc.,
by pressing DISPLAY.
The displayed information differs depending on
the disc type and player status.
You can play video/music/photo files on the
connected USB device.
For playable types of files, see “Playable Types
Example: when playing a BD-ROM
1
Connect the USB device to the
(USB) port on the unit.
Refer to the operating instructions of the
USB device before connecting.
Rear panel
A
B
C
D
Output resolution/Video frequency
Title number or name
USB device
The currently selected audio setting
Front panel
Available functions (
subtitle)
angle,
audio,
E
Playback information
Displays disc type, play mode, repeat type,
video codec, bit rate, playing status bar,
playing time, total time
USH OPEN
F
G
Chapter number
USB device
The currently selected angle
2
3
Press C/c to select
[Video],
[Music], or
[Photo].
Press X/x to select
(front)] or [USB device (rear)], then
[USB device
press
.
Note
• Do not remove the USB device during
operation. To avoid data corruption or damage
to the USB device, turn the system off when
connecting or removing the USB device.
US
36
Download from Www.Somanuals.com. All Manuals Search And Download.
To operate the iPod using the
remote
You can operate the iPod using the buttons on
the remote. The following table shows an
example of buttons that can be used.
Enjoying an iPod
You can enjoy the sound and charge the battery
of an iPod via the system.
Compatible iPod models
The compatible iPod models are as follows.
Update your iPod with the latest software before
using with the system.
Press
Operation
N, X
Same operation as the N/X button
of the iPod.
x
Pause.
m or M
. or >
Fast reverse or forward.
Same operation as the . or >
buttons of the iPod.
DISPLAY,
RETURN,
C
Same operation as the MENU button
of the iPod.
X/x
Same operation as the Click Wheel
of the iPod.
, c
Same operation as the Center button
of the iPod.
Note
• The iPod is charged when connected to the system
while the system is turned on.
• You cannot transfer songs onto the iPod.
• Sony cannot accept responsibility in the event that
data recorded to iPod is lost or damaged when using
an iPod connected to this unit.
• This product has been designed specifically to work
with iPod and has been certified to meet Apple
performance standards.
1
Connect the iPod to the
on the unit with the iPod’s USB cable.
(USB) port
• Do not remove the iPod during operation. To avoid
data corruption or damage to the iPod, turn the system
off when connecting or removing the iPod.
2
3
Press C/c to select [Music].
Press X/x to select [iPod (front)],
then press
.
The sound from the iPod is played on the
system.
You can operate the iPod using the buttons
on the remote.
For operation details, refer to the operating
instructions of the iPod.
US
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing files stored on a DLNA
server
Playing via a Network
You can play video/music/photo files on your
home server, such as a DLNA-certified network
audio system or a PC with software that enables
a DLNA-certified server function, by
Streaming BRAVIA Internet
Video
BRAVIA Internet Video serves as a gateway
delivering the selected Internet content and a
variety of on-demand entertainment straight to
your unit.
connecting the system to your home network.
1
Prepare for playing files on a DLNA
server.
• Set [Connection Server Settings]
1
Prepare for BRAVIA Internet Video.
2
3
Press C/c to select
[Video],
2
3
Press C/c to select
[Video],
[Music], or [Photo].
[Music], or [Photo].
Press X/x to select an Internet content
provider icon, then press
Press X/x to select a DLNA server, then
press
The file list or folder list appears.
.
.
When the Internet content list has not been
retrieved, it will be represented by an
unacquired icon or a new icon.
To use the control panel
Available Options
Various settings and playback operations are
available by pressing OPTIONS. The available
items differ depending on the situation.
The control panel appears when the video file
starts playing. The displayed items may differ
depending on Internet content providers.
To display again, press DISPLAY.
Common options
Items
Details
[Playback History
List]
Displays titles/tracks in the
playback history of a
BD-ROM/DVD-ROM/
CD-DA (music CD) using
Gracenote technology.
A
B
Control display
Press C/X/x/c or
for playback operations.
Playing status bar
[Search History]
[Search Contents]
Searches for related
information based on
keywords from Gracenote via
the Information Display.
Status bar, cursor indicating the current
position, playing time, duration of the video
file
C
D
The next video file name
Searches for BRAVIA
Internet Video content based
on keywords from Gracenote
via the Information Display.
The currently selected video file name and
rating
[Repeat Setting]
[Favorites List]
[Play/Stop]
Sets the repeat play.
Displays the Favorites List.
Starts or stops playback.
US
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Items
Details
Items
Details
[Play from beginning] Plays the item from the
beginning.
[Angle]
Switches to other viewing
angles when multi-angles are
recorded on BD-ROMs/DVD
VIDEOs.
[Information Display] Displays information on the
BD-ROM/DVD-ROM/
CD-DA (music CD) by using
Gracenote technology.
[IP Content Noise
Reduction]
Adjusts the video quality for
Internet content.
[Add to Favorites]
Adds an Internet content to
the Favorites List.
[Music] only
[Remove from
Favorites]
Erases an Internet content
from the Favorites List.
Items
Details
[Add Slideshow
BGM]
Registers music files in the
USB memory as slideshow
background music.
[Video] only
Items
Details
[Photo] only
[3D Output Setting] • Sets whether or not to output
3D video automatically.
Items
Details
Note
[Slideshow]
Starts a slideshow.
Changes the slideshow speed.
• 3D video from the HDMI
(IN 1) or HDMI (IN 2) jack
is output regardless of this
setting.
[Slideshow Speed]
[Slideshow Effect]
Sets the effect when playing a
slideshow.
[Video Settings]
• [Picture Quality Mode]:
Selects the picture settings
for different lighting
environments.
[Slideshow BGM]
• [Off]: Turns off the
function.
• [My Music from USB]: Sets
the music files registered in
[Add Slideshow BGM]. If
no music file is registered,
[(Not registered)] is
displayed.
• [FNR]: Reduces the random
noise appearing in the
picture.
• [BNR]: Reduces the
mosaic-like block noise in
the picture.
• [Play from disc]: Sets the
tracks on CD-DAs (music
CDs).
• [MNR]: Reduces minor
noise around the picture
outlines (mosquito noise).
[Rotate Left]
Rotates the photo
counterclockwise by
90 degrees.
[Play/Pause]
[Top Menu]
Starts or pauses playback.
Displays the BD’s or DVD’s
Top Menu.
[Rotate Right]
[View Image]
Rotates the photo clockwise
by 90 degrees.
[Menu/Popup Menu] Displays the BD-ROM’s
Displays the selected picture.
Pop-up Menu or DVD’s
menu.
[Title Search]
Searches for a title on BD-
ROMs/DVD VIDEOs and
starts playback from the
beginning.
[Chapter Search]
Searches for a chapter and
starts playback from the
beginning.
US
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the delay between
the picture and sound
(A/V SYNC)
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “A/V SYNC”
appears in the front panel display, then
press
or c.
3
Press X/x to adjust the delay between
the picture and sound.
You can adjust from 0 ms to 300 ms in 25
ms increments.
4
Press
.
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Note
• Depending on the input stream, A/V SYNC may not
be effective.
US
40
Download from Www.Somanuals.com. All Manuals Search And Download.
• “GAME ROCK”: The system provides the
sound for music/rhythm games.
Sound Adjustment
• “OMNI-DIR”: The same sound is audible
anywhere in the room.
Selecting the Effect to
Suit the Source
You can select a suitable sound mode for movies
or music.
Note
• Depending on the disc or source, when you select
“AUTO,” the beginning of the sound may be cut off
as the system selects the optimum mode
automatically. To avoid cutting the sound, select
other than “AUTO.”
• Depending on the input stream, the sound mode may
not be effective.
• When changing the sound mode while using the
S-AIR receiver, sound from the S-AIR receiver may
skip.
1
4
7
2
5
8
0
3
6
9
• When you play a Super Audio CD, this function does
not work.
Selecting the Audio
Format, Multilingual
Tracks, or Channel
SOUND
MODE
When the system is playing a BD/DVD VIDEO
or DATA CD/DATA DVD (DivX video files*)
recorded in multiple audio formats (PCM,
Dolby Digital, MPEG audio, or DTS) or
multilingual tracks, you can change the audio
format or language.
With a CD, you can select the sound from the
right or left channel and listen to the sound of the
selected channel through both the right and left
speakers.
Press SOUND MODE repeatedly during
playback until the desired mode appears in
the front panel display.
• “AUTO”: The system selects “MOVIE” or
“MUSIC” automatically to produce the sound
effect depending on the disc or sound stream.
• “MOVIE”: The system provides the sound for
movies.
• “HD-D.C.S.”: For movies on Blu-ray and
DVD, etc., “HD-D.C.S.” realizes precise
sound effects the way the Movie Sound
Designers intended for them to be.
• “3D SUR.”: “3D SUR.” is a unique Sony
algorithm used for playing 3D (three-
dimensional) content that provides a 3D sound
experience with depth and presence by
creating a virtual sound field close to your
ears.
* Except for U.S. models.
1
4
7
2
5
8
0
3
6
9
AUDIO
• “MUSIC”: The system provides the sound for
music.
• “SPORTS”: The system adds reverberation for
sports programs.
• “NEWS”: The system provides the sound for
voice programs, such as news.
US
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Press AUDIO repeatedly during playback to
select the desired audio signal.
Enjoying Multiplex
Broadcast Sound
(DUAL MONO)
You can enjoy multiplex broadcast sound when
the system receives or plays a Dolby Digital
multiplex broadcast signal.
The audio information appears on the TV
screen.
x BD/DVD VIDEO
Depending on the BD/DVD VIDEO, the choice
of language varies.
When 4 digits are displayed, they indicate a
language code. See “Language Code List”
(page 81) to confirm which language the code
represents. When the same language is
displayed two or more times, the BD/DVD
VIDEO is recorded in multiple audio formats.
Note
• To receive the Dolby Digital signal, you need to
connect a TV or other component to the unit with a
TV is compatible with the Audio Return Channel
signal via an HDMI cable.
x DVD-VR
The types of sound tracks recorded on a disc are
displayed.
Example:
• [ Stereo]
• [ Stereo (Audio1)]
• [ Stereo (Audio2)]
• [ Main]
1
4
7
2
5
8
0
3
6
9
AUDIO
• [ Sub]
• [ Main/Sub]
Note
• [ Stereo (Audio1)] and [ Stereo (Audio2)] do not
appear when only one audio stream is recorded on the
disc.
x DATA CD (DivX video file)/DATA DVD
(DivX video file) (Except for U.S. models)
The choice of DATA CD or DATA DVD audio
signal formats differs, depending on the DivX
video file contained on the disc. The format
appears on the TV screen.
Press AUDIO repeatedly until the desired
signal appears in the front panel display.
• “MAIN”: Sound of the main language will be
output.
x CD
• [ Stereo]: The standard stereo sound.
• [ 1/L]: The sound of the left channel
(monaural).
• “SUB”: Sound of the sub language will be
output.
• “MAIN/SUB”: Mixed sound of both the main
and sub languages will be output.
• [ 2/R]: The sound of the right channel
(monaural).
US
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the tonal balance
Using the Sound Effect
You can adjust the sound by changing the tonal
balance of the sound.
1
Press TONE repeatedly until the
desired setting appears in the front
panel display.
1
4
7
2
5
8
0
3
6
9
TONE
• “BASS”: You can adjust the bass
frequencies.
• “TREBLE”: You can adjust the treble
frequencies.
C/X/x/c,
2
Press X/x to adjust the sound.
The adjusted value appears in the front
panel display. You can set the value from
–6.0 to +6.0.
SYSTEM
MENU
Enjoying sound at low volume
You can enjoy sound effects or dialog, as you
would in a movie theater, even at low volume. It
is useful for watching movies at night.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “NIGHT
MODE” appears in the front panel
display, then press
or c.
3
Press X/x to select a setting.
• “NIGHT ON”: On.
• “NIGHT OFF”: Off.
4
Press SYSTEM MENU.
The system menu turns off.
Note
• When sound is output from the center speaker, this
effect is more pronounced, as speech (movie dialog,
etc.) is easy to hear. When sound is not output from
the center speaker, the system optimally adjusts the
volume.
US
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual tuning
Press TUNING +/– repeatedly.
Tuner
3
Adjust the volume by pressing
VOL +/–.
Listening to the Radio
You can enjoy radio sound with the system’s
If an FM program is noisy
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
speakers.
"/1
1
2
Press SYSTEM MENU.
1
4
7
2
5
8
0
3
6
9
Number
buttons
Press X/x repeatedly until “FM MODE”
appears in the front panel display.
D.TUNING
C/X/x/c,
3
4
Press
or c.
Press X/x to select “MONO.”
• “STEREO”: Stereo reception.
• “MONO”: Monaural reception.
FUNCTION
TUNING +/–
PRESET +/–
x
5
Press SYSTEM MENU.
SYSTEM
MENU
VOL +/–
The system menu turns off.
To turn off the radio
Current station
Current band and preset number
Press "/1.
FM
7
Presetting radio stations
88.00 MHz
You can preset up to 20 stations. Before tuning,
make sure to turn down the volume to minimum.
1
Press FUNCTION repeatedly until
“TUNER FM” appears in the front panel
display.
1
2
Press FUNCTION repeatedly until
“TUNER FM” appears in the front panel
display.
2
Press and hold TUNING +/– until the
auto scanning starts.
Scanning stops when the system tunes in a
station.
Select the radio station.
3
4
Press SYSTEM MENU.
Automatic tuning
Press and hold TUNING +/– until the auto
scanning starts.
Press X/x repeatedly until “MEMORY”
appears in the front panel display, then
press
or c.
[Auto Tuning] appears on the TV screen.
Scanning stops when the system tunes in a
station.
A preset number appears in the front panel
display.
To stop the automatic tuning manually,
press TUNING +/–.
US
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Press X/x to select the preset number
you want.
Selecting a radio station by
inputting a frequency directly
When you know the frequencies, you can select
radio stations by inputting the frequencies
directly.
Tip
• You can select the preset number directly by
pressing the number buttons.
1
Press FUNCTION repeatedly until
“TUNER FM” appears in the front panel
display.
Press
.
“COMPLETE” appears in the front panel
display, and the station is stored.
2
3
Press D.TUNING.
7
8
Repeat Steps 2 to 6 to store other
stations.
Press the number buttons to select the
frequencies.
Press SYSTEM MENU.
4
Press
.
The system menu turns off.
To change the preset number
Select the desired preset number by pressing
PRESET +/–, then perform the procedure from
Step 3.
Selecting the preset station
1
Press FUNCTION repeatedly until
“TUNER FM” appears in the front panel
display.
The last received station is tuned in.
2
Press PRESET +/– repeatedly to select
the preset station.
The preset number and frequency appear on
the TV screen and front panel display.
Each time you press the button, the system
tunes in one preset station.
Tip
• You can select the preset station number directly
by pressing the number buttons.
US
45
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the ID of the unit
1
Set the S-AIR ID switch of the unit to
the desired ID.
External Audio Device
Using an S-AIR Product
S-AIR ID
A
B
C
About S-AIR products
There are two types of S-AIR product.
• S-AIR main unit (this unit): This is for
transmitting sound. You can use up to three
S-AIR main units. (The number of usable
S-AIR main units depends on the use
environment.)
S-AIR ID switch
You can select any ID (A, B, or C).
2
3
Press "/1.
The system turns on.
Set the S-AIR sub unit to the same ID.
• S-AIR sub unit: This is for receiving sound.
Wireless transmission is activated as
follows (example):
– Surround amplifier (supplied): You
can enjoy surround speaker sound
wirelessly.
– S-AIR receiver (optional): You can
ID A
enjoy system sound in another room.
Room A
S-AIR main unit
ID A
ID A
To set the ID of the surround
amplifier
S-AIR sub unit
(surround amplifier)
1
2
3
Make sure that the SURROUND
SELECTOR switch of the surround
amplifier is set to SURROUND.
Room B
Set the S-AIR ID switch of the surround
amplifier to match the ID (A, B, or C) of
the unit.
S-AIR sub unit
(S-AIR receiver)
(not supplied)
Press "/1 on the surround amplifier.
When wireless transmission is activated,
the S-AIR/STANDBY indicator of the
surround amplifier turns green.
For details of the S-AIR/STANDBY
indicator, see “Surround amplifier”
Setting the S-AIR ID to activate
wireless transmission
For the surround amplifier
For the S-AIR receiver
Simply by matching the ID of the unit and the
S-AIR sub unit, you can activate wireless
transmission.
To set the ID of the S-AIR
receiver
Refer to the operating instructions of the S-AIR
receiver.
US
46
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Adjust the volume on the S-AIR
receiver.
To enjoy a 7.1 channel system
You can enjoy the more realistic surround sound
effect of 7.1 channels when you use the Wireless
Surround Speaker Kit (WAHT-SBP2, optional).
For details, refer to the operating instructions of
the Wireless Surround Speaker Kit.
Enjoying the S-AIR receiver
while the unit is in standby
mode
In this case, set [Surround Back] in [Speaker
For the S-AIR receiver
Enjoying the system’s sound in
another room
You can enjoy the S-AIR receiver while the unit
is in standby mode by setting [Standby] to [On].
1
Press HOME.
For the S-AIR receiver
The home menu appears on the TV screen.
You can enjoy the system’s sound in another
room by using the S-AIR receiver.
2
3
Press C/c to select
Press X/x to select [System Settings],
then press
Press X/x to select [S-AIR Settings],
then press
[Setup].
1
Press HOME.
.
The home menu appears on the TV screen.
4
.
2
3
Press C/c to select
Press X/x to select [System Settings],
then press
Press X/x to select [S-AIR Settings],
then press
[Setup].
The [S-AIR Settings] display appears.
.
5
6
Press X/x to select [Standby], then
press
.
4
.
Press X/x to select the desired setting.
The [S-AIR Settings] display appears.
• [On]: You can enjoy the S-AIR receiver
while the unit is in standby mode or turned
on. The power consumption during
standby mode increases.
• [Off]: You cannot enjoy the S-AIR
receiver while the unit is in standby mode.
5
6
Press X/x to select [Mode], then press
.
Press X/x to select the desired setting.
• [Party]: The S-AIR receiver outputs
sound according to functions set on the
unit.
7
Press
.
The setting is made.
• [Separate]: You can set the desired
function for the S-AIR receiver while unit
functions do not change.
Note
• When you turn the system off while [Standby] is set
to [On], “S-AIR” flashes (when wireless transmission
between the unit and S-AIR receiver is not activated),
or lights up (when wireless transmission between the
unit and S-AIR receiver is activated) in the front
panel display.
7
8
Press
.
The setting is made.
When you select [Separate] in Step 6,
press S-AIR CH on the S-AIR receiver
to select the function.
The S-AIR receiver’s function changes as
follows.
“MAIN UNIT” t “TUNER FM” t
“AUDIO” t …
To enjoy the same function as the unit,
select “MAIN UNIT.”
US
47
Download from Www.Somanuals.com. All Manuals Search And Download.
instrument, such as a paper clip, can be
used.)
Identifying the unit with a
specific S-AIR sub unit
(Pairing operation)
x For the S-AIR receiver
Refer to the operating instructions of the
S-AIR receiver.
For the surround amplifier
For the S-AIR receiver
9
Press C/c to select [Start], then press
.
The unit starts pairing.
When using S-AIR products, neighbors may
also receive your system’s sound if IDs are the
same, or you may receive sound from neighbors.
To prevent this, you can identify the unit with a
specific S-AIR sub unit by performing the
pairing operation.
The PAIRING indicator of the surround
amplifier flashes when pairing starts.
When wireless transmission is activated,
the PAIRING indicator of the surround
amplifier turns on.
To cancel pairing, select [Cancel].
When you perform pairing, wireless
transmission is activated between the paired
main unit and S-AIR sub unit only.
Note
• Perform pairing within several minutes of Step
9. If you do not, [Pairing failed. Retry?] appears
on the TV screen. To continue pairing, select
[OK] and press , then start again from Step 8.
To cancel pairing, select [Cancel].
1
2
Place the S-AIR sub unit that you want
to pair near the unit.
Match the IDs of the unit and the S-AIR
sub unit.
To cancel pairing
Change the ID of the main and sub unit
• To set the ID of the unit, see “To set the ID
• To set the ID of the surround amplifier,
Checking the S-AIR status of
the unit
• To set the ID of the S-AIR receiver, refer
to the operating instructions of the S-AIR
receiver.
You can check the S-AIR status such as the
S-AIR ID or pairing information.
3
Press HOME.
The home menu appears on the TV screen.
1
Press HOME.
4
5
Press C/c to select
Press X/x to select [System Settings],
then press
Press X/x to select [S-AIR Settings],
then press
[Setup].
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [System Settings],
then press
Press X/x to select [S-AIR Settings],
then press
[Setup].
.
6
.
.
4
The [S-AIR Settings] display appears.
.
7
8
Press X/x to select [Pairing], then
The [S-AIR Settings] display appears.
The S-AIR ID of the unit appears on the
[Info] line. When the unit is paired,
[Pairing] appears after the ID.
press
.
Start pairing of the S-AIR sub unit.
x For the surround amplifier
Press "/1 on the surround amplifier to turn
on the surround amplifier and press
PAIRING on the rear panel of the surround
amplifier. (To press PAIRING, a slim
5
Press RETURN.
The system returns to the previous display.
US
48
Download from Www.Somanuals.com. All Manuals Search And Download.
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
If wireless transmission is
unstable
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing the
transmission channel (frequency) of the other
wireless system(s). For details, refer to the operating
instructions of the other wireless system(s).
For the surround amplifier
For the S-AIR receiver
If you use multiple wireless systems, such as
wireless LAN or Bluetooth, the transmission of
S-AIR signals or other wireless signals may be
unstable. In this case, the transmission may be
improved by changing the following [RF
Change] setting.
1
Press HOME.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [System Settings],
then press
Press X/x to select [S-AIR Settings],
then press
[Setup].
.
4
.
The [S-AIR Settings] display appears.
5
6
Press X/x to select [RF Change], then
press
Press X/x to select the desired setting,
then press
.
.
• [Auto]: Normally select this. The system
changes [RF Change] to [On] or [Off]
automatically.
• [On]: The system transmits sound by
searching for the better channel for
transmitting.
• [Off]: The system transmits sound by
fixing the channel for transmitting.
7
8
Press
.
The setting is made.
When you set [RF Change] to [Off],
select the ID so that wireless
transmission is most stable (page 46).
Note
• In most cases, you will not need to change this
setting.
– If [RF Change] is set to [Off], transmission
between the unit and S-AIR sub unit can be
performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
US
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the connected component, the Control
for HDMI function may not work. Refer to the
operating instructions supplied with the component.
• The Control for HDMI function may not work if you
connect other than a Sony component, even if the
component is compatible with the Control for HDMI
function.
Other Operations
Using the Control for
HDMI Function for
“BRAVIA” Sync
This function is available on TVs with the
“BRAVIA” Sync function.
By connecting Sony components that are
compatible with the Control for HDMI function
with an HDMI cable, operation is simplified as
below:
Preparing for the Control for
HDMI function
(Control for HDMI - Easy Setting)
If your TV or other component is compatible
with the Control for HDMI - Easy Setting
function, you can set the system’s or other
components’ [Control for HDMI] function
automatically by setting the TV. For details,
refer to the operating instructions of the TV or
other components.
If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control
for HDMI function of the system, TV, and other
components manually.
Note
• For details on setting the TV, refer to the operating
instructions of the TV.
Control for HDMI is a mutual control function
standard used by CEC (Consumer Electronics
Control) for HDMI (High-Definition
Multimedia Interface).
1
2
Make sure that the system and the TV
are connected with an HDMI cable.
Turn on the TV and other components
connected via the HDMI connection,
and press [/1 to turn on the system.
The Control for HDMI function will not work
when you connect this system to a component
which is not compatible with the Control for
HDMI function.
3
Set the Control for HDMI function of the
TV.
There are convenient buttons on the system’s
remote for operating the TV, such as
THEATER, ONE-TOUCH PLAY, and AV ?/1.
refer to the operating instructions of the TV.
The Control for HDMI functions for the
system, TV, and other components are
simultaneously set to on.
To set the [Control for HDMI]
function of the system to on/off
manually
ONE-TOUCH
PLAY
AV
THEATER
BRAVIA Sync
1
2
Press HOME.
STB
TV
BD
The home menu appears on the TV screen.
Press C/c to select
[Setup].
US
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select [System Settings],
then press
.
Enjoying a component that is
connected to the system via an
HDMI cable
Press X/x to select [HDMI Settings],
then press
.
The [HDMI Settings] display appears.
(Routing Control)
5
6
Press X/x to select [Control for HDMI],
then press
Press X/x to select the setting, then
press
.
When you perform One-Touch Play via the
connected component, the system turns on and
sets the system’s function to “HDMI1” or
“HDMI2” (depending on the HDMI jack in use),
and your TV’s input is set to the HDMI input to
which the system is connected automatically.
.
• [On]: On.
• [Off]: Off.
Note
• Make sure that the component is connected to the
HDMI (IN 1) or HDMI (IN 2) jack on the system via
an HDMI cable, and the Control for HDMI function
of the connected component is set to on.
Turning the system off in sync
with the TV
(System Power Off)
When you turn the TV off by using the POWER
button on the TV’s remote or AV ?/1 on the
system’s remote, the system turns off
automatically.
Using the Theater Mode
(Theater Mode)
Press THEATER.
Note
• This function depends on the settings of your TV. For
details, refer to the operating instructions of the TV.
If your TV is compatible with the Theater Mode,
you can enjoy optimal image and sound quality
suited for movies, and the System Audio Control
function is activated automatically.
Watching BD/DVD by a single
button press
Enjoying the sound of the
content on the TV screen via
the system’s speakers
(One-Touch Play)
Press ONE-TOUCH PLAY.
The system and your TV turn on, your TV’s
input is set to the HDMI input to which the
system is connected, and the system starts
playing a disc automatically.
(System Audio Control)
You can simplify operation to enjoy sound of the
TV or other components.
The System Audio Control function is also
activated automatically.
To use this function, connect the system and the
TV with an audio cord and an HDMI cable, or
the system and the other components with
Also, when you insert a disc, One-Touch Play is
enabled. If One-Touch Play does not start (in the
case of inserting a disc that is not compatible
with the auto playback function), press
FUNCTION repeatedly to select “BD/DVD”
and press N or ONE-TOUCH PLAY.
You can use the System Audio Control function
as follows:
• When the system is turned on, the sound of the
TV or other components can be output from
the speakers of the system.
• When sound of the TV or other components is
output from the speakers of the system, you
US
51
Download from Www.Somanuals.com. All Manuals Search And Download.
can change the output method to the speakers
of the TV via the TV menu.
Changing the language for the
on-screen display of the TV
• When sound of the TV or other components is
output from the speakers of the system, you
can adjust the volume and turn off the sound of
the system using the TV remote.
(Language Follow)
When you change the language for the on-screen
display of the TV, the system’s on-screen
display language is also changed after turning
the system off and on.
Note
• While the TV is in PAP (picture and picture) mode,
the System Audio Control function will not work.
• Depending on the TV, when you adjust the unit's
volume, the volume level appears on the TV screen.
In this case, the volume level that appears on the TV
screen and the unit's front panel display may differ.
Calibrating the
Appropriate Settings
Automatically
[Auto Calibration]
Setting the Maximum Volume
Level of the System
(Volume Limit)
When the System Audio Control function is
activated, loud sound may be output depending
on the volume level of the system. You can
prevent this by limiting the maximum level of
the volume. For details, see [Volume Limit]
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
Note
• The system outputs a loud test sound when [Auto
Calibration] starts. You cannot turn the volume
down. Give consideration to children and neighbors.
1
Press HOME.
Receiving the digital audio
signal of the TV
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Audio Settings],
then press
Press X/x to select [Auto Calibration],
then press
[Setup].
(Audio Return Channel)
The system can receive the digital audio signal
of the TV via an HDMI cable when your TV is
compatible with the Audio Return Channel
function. You can enjoy TV sound via the
system by using just one HDMI cable. For
.
4
.
The confirmation display for [Auto
Calibration] appears.
5
Connect the calibration mic to the
A.CAL MIC jack on the rear panel.
Operating the system via the
TV remote
Set up the calibration mic at ear level using
a tripod, etc. (not supplied). The front of
each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic.
(Remote Easy Control)
You can control the basic functions of the
system via the TV remote when the system’s
video output is displayed on the TV screen. For
details, refer to the operating instructions of the
TV.
US
52
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Confirm the result of [Auto
Calibration].
The conclusions appear on the TV screen.
Press C/cto change the page. The first page
shows the distance of the speakers. The
second page shows the level of the
speakers.
L
A
.C
A
IC
M
2
C
-A
M
C
E
Note
• If measurement fails, follow the message then
retry [Auto Calibration].
9
Press X/x to select [OK] or [Cancel],
then press
.
x The measurement is OK.
Disconnect the calibration mic, then select
[OK]. The result is implemented.
Calibration mic
x The measurement is not OK.
Follow the message, then select [OK] to
retry.
Note
• While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
6
7
Press X/x to select [OK].
To cancel, select [Cancel].
Press
.
– do not insert a disc.
– do not disconnect the calibration mic.
[Auto Calibration] starts.
The system adjusts the speaker settings
automatically.
For proper calibration results, please
remain quiet during the measurement.
Setting the Speakers
[Speaker Settings]
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
Note
• Before [Auto Calibration], make sure that the
surround amplifier turns on and you install the
surround amplifier in the appropriate location. If
you install the surround amplifier in an improper
location, such as another room, proper
measurement will not be obtained.
• When you use the Wireless Surround Speaker
Kit (WAHT-SBP2, optional) for the surround
appropriate location and turn the surround
amplifier on. To use the surround back speakers,
set [Surround Back] in [Speaker Settings] to
[Yes] (page 54)
1
Press HOME.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Audio Settings],
then press
Press X/x to select [Speaker Settings],
then press
The [Speaker Settings] display appears.
[Setup].
.
4
.
US
53
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select the item, then press
.
1
2
3
Check the following settings.
x [Connection]
4
If you do not connect center or surround
speakers, set the parameters for [Center] and
[Surround]. Since the front speaker and
subwoofer settings are fixed, you cannot change
them.
A
5
6
When you use the Wireless Surround Speaker
Kit (WAHT-SBP2, optional) for the surround
also.
A
7
8
[Front]
[Front Left/Right] 10 ft/3.0 m: Set the front
speaker distance.
[Yes]
[Center]* 10 ft/3.0 m: Set the center speaker
distance.
[Surround Left/Right]* 10 ft/3.0 m: Set the
surround speaker distance.
[Surround Back Left/Right]* 10 ft/3.0 m: Set the
surround back speaker distance.
[Subwoofer] 10 ft/3.0 m: Set the subwoofer
distance.
[Center]
[Yes]: Normally select this.
[None]: Select this if no center speaker is used.
[Surround]
[Yes]: Normally select this.
[None]: Select this if no surround speaker is
used.
* This item appears when you set it to [Yes] in the
[Surround Back]
[Connection] setting.
[Yes]: Select this if surround back speakers are
used.
Note
[None]: Select this if no surround back speakers
is used.
• Depending on the input stream, [Distance] may not
be effective.
[Subwoofer]
Tip
[Yes]
• You can change measurement units (feet or meters)
by pressing the color button (RED).
x [Distance]
x [Level]
When you move the speakers, be sure to set the
parameters of the distance (A) from the
listening position to the speakers.
You can set the parameters from 0 to 23 feet (0.0
to 7.0 meters).
You can adjust the sound level of the speakers.
You can set the parameters from –6.0 dB to +6.0
dB. Be sure to set [Test Tone] to [On] for easy
adjustment.
[Front Left/Right] 0.0 dB: Set the front speaker
level.
The numbers in the illustration indicate the
following:
[Center]* 0.0 dB: Set the center speaker level.
[Surround Left/Right]* 0.0 dB: Set the surround
speaker level.
[Surround Back Left/Right]* 0.0 dB: Set the
surround back speaker level.
[Subwoofer] 0.0 dB: Set the subwoofer level.
* This item appears when you set it to [Yes] in the
[Connection] setting.
1Center speaker
2Front left speaker (L)
3Front right speaker (R)
4Subwoofer
5Surround left speaker (L)
6Surround right speaker (R)
7Surround back left speaker (L) (optional)
8Surround back right speaker (R) (optional)
US
54
Download from Www.Somanuals.com. All Manuals Search And Download.
x [Test Tone]
The speakers will emit a test tone to adjust
[Level].
Using the Sleep Timer
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
The time can be preset in intervals of 10
minutes.
[Off]: The test tone is not emitted from the
speakers.
[On]: The test tone is emitted from each speaker
in sequence while adjusting level. When you
select one of the [Speaker Settings] items, the
test tone is emitted from each speaker in
sequence.
Press SLEEP.
Each time you press SLEEP, the minutes display
(the remaining time) changes by 10 minutes.
When you set the sleep timer, “SLEEP” flashes
in the front panel display.
Adjust the sound level as follows.
1
2
Set [Test Tone] to [On].
To check the remaining time
Press X/x to select [Level], then press
Press SLEEP once.
.
To change the remaining time
3
4
Press X/x to select the desired speaker
Press SLEEP repeatedly to select the desired
time.
type, then press
.
Press C/c to select the left or right
speaker, then press X/x to adjust the
level.
5
6
7
Press
.
Deactivating the Buttons
on the Unit
Repeat Steps 3 to 5.
Press RETURN.
(Child Lock)
The system returns to the previous display.
You can deactivate the buttons on the unit
(except for "/1) for preventing misoperation,
such as child mischief (child lock function).
8
Press X/x to select [Test Tone], then
press
.
9
Press X/x to select [Off], then press
Press x on the unit for 5 seconds.
.
“CHILD LOCK” and “ON” appear in the front
panel display.
Note
• The test tone signals are not output from the HDMI
OUT jack.
The child lock function is activated and the
buttons on the unit are locked. (You can operate
the system by using the remote.)
To cancel, press x for 5 seconds so that
“CHILD LOCK” and “OFF” appear in the front
panel display.
Tip
• To adjust the volume of all the speakers at one time,
press VOL +/–.
Note
• When you operate the buttons on the unit while the
child lock function is on, “CHILD LOCK” appears in
the front panel display.
US
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Button
Remote’s mode
TV
STB
z
Controlling Your TV or
Other Components with
the Supplied Remote
You can control your TV and other components
such as a cable box or digital satellite receiver
with the supplied remote. The remote is initially
set to control Sony components.
z
z
SLEEP (INPUT)
a
Color buttons
(YELLOW/
BLUE/RED/
GREEN)
z
z
TOP MENU
(GUIDE)
z
z
z
z
FAVORITES
POP UP/MENU
(LIST)
You can control non-Sony components by
changing the preset code of the remote. For
operation, see “Changing the preset code of the
You can also set a new code which is not stored
on the remote. For operation, see “Programming
z
z
z
z
z
z
z
z
C/X/x/c,
RETURN
HOME (MENU)
OPTIONS
(TOOLS)
z
z
FUNCTION
(PAGE –)
a
a
SOUND MODE
(PAGE +)
Note
• When you replace the batteries of the remote, the
remote setting may be reset to the default (SONY)
setting.
z
z
z
z
z
z
z
z
z
z
z
z
./>
a
a
z
z
z
z
z
m/M
H
Controlling your components
with the supplied remote
X
x
1
Press the TV or STB operation mode
button that matches the component
you want to control.
MUTING
VOL +/–
CH +/–
DISPLAY
z
z
z
2
Press the appropriated buttons listed
in the following table.
• z: The button can be used with the
default setting of the remote.
SYSTEM
MENU (JUMP)
z
z
z
z
a
a
H while
pressingz(starts
recording)
• a: The button can be used when you
change the preset code of the remote.
Button
Remote’s mode
X while pressing
z (pauses
recording)
TV
STB
z
z
z
z
z
z
z
z
AV "/1
x while pressing
z (stops
recording)
z
Number buttons
z
z
ENTER
z
AUDIO
a
SUBTITLE (CC)
TONE (WIDE)
a
US
56
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you do not operate the remote for more than 10
seconds during presetting mode, the remote exits
from presetting mode.
Note
• In TV or STB mode, if you press any of the buttons
above, the TV or STB operation mode button lights
up. (However, depending on the code setting, some
buttons may not work, and the TV or STB operation
mode button may not light up.)
Programming the remote code
from another remote (Learning
mode)
• If you press other than the buttons above when the
remote is in TV or STB mode, the TV or STB
operation mode button does not light up.
• Depending on the TV or component, you may not be
able to use some of the buttons.
You can program a remote code that is not
stored in the supplied remote from a different
component’s remote, such as a TV remote.
Buttons other than THEATER,
ONE-TOUCH PLAY, [/1, BD, TV, and STB
are assignable.
Changing the preset code of
the remote (Preset mode)
1
Press HOME.
1
Press HOME.
The home menu appears on the TV screen.
The home menu appears on the TV screen.
2
3
Press C/c to select
Press X/x to select [Remote Controller
Setting Guide], then press
Press X/x to select [Preset Mode], then
press
[Setup].
2
3
Press C/c to select
Press X/x to select [Remote Controller
Setting Guide], then press
Press X/x to select [Learning Mode],
then press
Press
[Setup].
.
.
4
5
4
.
.
Press X/x to select the component type
that you want to operate with the
5
6
.
Prepare the other remote with the
button which you want to program to
the supplied remote.
supplied remote, then press
.
6
7
Press X/x to select the device’s
manufacturer, then press
.
7
Press TOP MENU while pressing the
operation mode button TV (for a TV) or
STB (for a cable box, digital satellite
receiver, digital video recorder, etc.)
for one second.
Press POP UP/MENU while pressing
the operation mode button TV (for a TV)
or STB (for a cable box, digital satellite
receiver, digital video recorder, etc.).
The remote enters Preset mode. The TV or
STB operation mode button (whichever
button you pressed) starts flashing.
The remote enters Learning mode. The BD
operation mode button lights up and the TV
or STB operation mode button (whichever
button you pressed) starts flashing.
8
When the TV or STB operation mode
button starts flashing, enter the code
on the TV screen using the number
buttons, then press ENTER.
8
Press the button on the supplied
remote to which you want to assign the
new remote code.
If you successfully set the code, the TV or
STB operation mode button will flash twice
slowly. If the setting is unsuccessful, the
TV or STB operation mode button will
flash five times quickly.
The TV or STB operation mode button
lights up.
Note
• If the pressed button has already been assigned
a remote code, the TV or STB operation mode
button flashes five times quickly. In this case,
clear the learned remote code of the button
(page 58), then assign the new desired remote
code.
Note
• You can quit Preset mode by pressing the TV or STB
operation mode button (whichever button is
flashing).
US
57
Download from Www.Somanuals.com. All Manuals Search And Download.
• You cannot use z individually. z is used with
H, X, or x. When learning, press H, X, or
x while pressing z.
Note
• When you clear the programmed remote code, the
button’s operation returns to the default setting.
9
10
Point the remotes at each other.
Press the button on the other remote
that you want to program to the
supplied remote.
Clearing all the preset and
programmed remote codes
from the remote’s memory
Note
• If you do not press a button for more than 10
seconds after Step 8, the supplied remote status
returns to its status after Step 7. Re-perform
from Step 8.
1
Press and hold AV ?/1 first, then press
VOL –, then press CH –.
The BD, TV, and STB operation buttons
light up.
11
Repeat Steps 8 to 10 to continue
programming more buttons.
2
Release all buttons.
If you successfully program the remote
code, the BD operation mode button will
flash twice slowly. If the setting is
unsuccessful, the TV or STB operation
mode button will flash five times quickly.
The BD, TV, and STB operation mode
buttons turn off and all the added remote
codes are cleared. The remote returns to its
default settings.
Note
• You can exit from Learning mode by pressing the TV
or STB operation mode button (whichever button is
flashing).
Saving Power in Standby
Mode
• If you do not press a button to be programmed during
Learning mode for more than 1 minute, the remote
exits from Learning mode.
Check that the following settings are made:
– [Control for HDMI] in [HDMI Settings] is set
To clear a programmed remote
code
– [Standby] in [S-AIR Settings] is set to [Off]
1
Follow Steps 1 to 7 of “Programming
2
Press [/1 for more than 1 second.
The TV or STB operation mode button
flashes twice.
3
4
Press the button on the supplied
remote for which you want to clear the
remote code.
If you successfully clear the remote code,
the BD operation mode button will flash
twice slowly. If the clearing is
unsuccessful, the BD operation mode
button will flash five times quickly.
Repeat Step 3 to continue clearing
more buttons.
US
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Icon
Explanation
Makes the screen settings
Settings and Adjustments
according to the type of
connecting jacks.
Using the Setup Display
You can make various adjustments of items such
Makes the audio settings
according to the type of
connecting jacks.
as picture and sound.
Select
(Setup) on the home menu when you
Makes detailed settings for BD/
need to change the settings of the system.
The default settings are underlined.
DVD playback.
Note
Makes detailed settings for the
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
Parental Control function.
1
2
Press HOME.
Makes detailed settings for
Super Audio CD playback.
The home menu appears on the TV screen.
Press C/c to select
[Setup].
Makes the system-related
settings.
Makes detailed settings for
Internet and network.
Re-runs the Easy Setup to make
the basic settings.
Resets the system to the factory
settings.
3
Press X/x to select the setup category
icon to change, then press
.
Example: [Screen Settings]
[Remote Controller
Setting Guide]
Setup
TV Type
Set the screen aspect ratio of your TV.
Screen Format
Original
DVD Aspect Ratio
Cinema Conversion Mode
Letter Box
Auto
x [Preset Mode]
You can change the preset code of the remote for
controlling non-Sony components. For details,
You can setup the following options.
Icon
Explanation
Makes the remote settings for
operating the TV or other
components.
x [Learning Mode]
You can assign a remote code for an operation
different from the preset operations of the
remote’s buttons. For details, see “Programming
Updates the software of the
system.
US
59
Download from Www.Somanuals.com. All Manuals Search And Download.
x [DVD Aspect Ratio]
[Letter Box]: Displays a wide picture with black
bands on the top and bottom.
[Network Update]
You can update and improve the functions of the
system.
For information about update functions, refer to
the following website:
[Pan & Scan]: Displays a full-height picture on
the entire screen, with trimmed sides.
During a software update, “UPDATING”
appears in the front panel display and video
signals via HDMI may not be displayed. After
the update completes, the main unit
automatically turns off. Please wait for the
software update to complete; do not turn the
main unit on or off, or operate the main unit or
TV.
x [Cinema Conversion Mode]
[Auto]: Normally select this. The unit
automatically detects whether the material is
video-based or film-based, and switches to the
appropriate conversion method.
[Video]: The conversion method suited for
video-based material will always be selected
regardless of the material.
[Screen Settings]
x [3D Output Setting]
[Auto]: Normally select this.
[Off]: Select this to display all contents in 2D.
x [Output Video Format]
Note
[HDMI]: Normally select [Auto]. Select
[Original Resolution] to output the resolution
recorded on the disc. (When the resolution is
lower than SD resolution, it is scaled up to SD
resolution.)
[Component Video]: Select the resolution that
suits your TV.
[Video]: Automatically sets the lowest
resolution.
• 3D video from the HDMI (IN 1) or HDMI (IN 2) jack
is output regardless of this setting.
x [TV Screen Size Setting for 3D]
Sets the screen size of your 3D compatible TV.
Note
• This setting does not apply to 3D video from the
HDMI (IN 1) or HDMI (IN 2) jack.
Note
x [TV Type]
• When connecting the HDMI OUT jack and other
video output jacks at the same time, select
[Component Video].
[16:9]: Select this when connecting to a wide-
screen TV or a TV with a wide-mode function.
[4:3]: Select this when connecting to a 4:3
screen TV without a wide-mode function.
• If no picture appears when setting [HDMI] or
[Component Video] resolution, try another resolution
setting.
x [Screen Format]
[Original]: Select this when connecting to a TV
with a wide-mode function. Displays a 4:3
screen picture in 16:9 aspect ratio even on a
wide-screen TV.
[Fixed Aspect Ratio]: Changes the picture size
to fit the screen size with the original picture
aspect ratio.
x [BD/DVD-ROM 1080/24p Output]
[Auto]: Outputs 1920 × 1080p/24 Hz video
signals only when connecting a 1080/24p-
compatible TV using the HDMI OUT jack.
[Off]: Select this when your TV is not
compatible with 1080/24p video signals.
US
60
Download from Www.Somanuals.com. All Manuals Search And Download.
[On]: The system reproduces the sound track
with the kind of dynamic range that the
recording engineer intended.
x [YCbCr/RGB (HDMI)]
[Auto]: Automatically detects the type of
external device, and switches to the matching
color setting.
[YCbCr (4:2:2)]: Outputs YCbCr 4:2:2 video
signals.
[YCbCr (4:4:4)]: Outputs YCbCr 4:4:4 video
signals.
[RGB]: Select this when connecting to a device
with an HDCP-compliant DVI jack.
x [Attenuate - AUDIO]
Distortion may occur when you listen to a
component connected to the AUDIO (AUDIO
IN L/R) jacks. You can prevent distortion by
reducing the input level on the unit.
[On]: Attenuates the input level. The output
level is changed.
[Off]: Normal input level.
x [HDMI Deep Color Output]
[Auto]: Normally select this.
[12bit], [10bit]: Outputs 12bit/10bit video
signals when the connected TV is compatible
with Deep Color.
[Off]: Select this when the picture is unstable or
colors appear unnatural.
x [Audio Output]
The system cannot output multi-channel sound
from both the HDMI (OUT) jack and system’s
speakers simultaneously.
[Speaker]: Outputs multi-channel sound from
the system’s speakers only.
x [Pause Mode] (BD/DVD VIDEO/DVD-R/
DVD-RW only)
[Auto]: The picture, including subjects that
move dynamically, is output with no jitter.
Normally select this position.
[Frame]: The picture, including subjects that do
not move dynamically, is output in high
resolution.
[Speaker + HDMI]: Outputs multi-channel
sound from the system’s speakers and 2-channel
linear PCM signals from the HDMI (OUT) jack.
[HDMI]: Outputs multi-channel sound from the
HDMI (OUT) jack only. Sound format depends
on the connected component.
Note
• Even if [HDMI] or [Speaker + HDMI] is selected, the
sound of functions other than “BD/DVD,” “D.
MEDIA,” “HDMI1,” or “HDMI2” is output from the
system’s speakers, not from the HDMI (OUT) jack.
• When you set [Audio Output] to [HDMI], the
SOUND MODE, “TONE,” “NIGHT MODE,” and
“SUR.SETTING” functions are disabled.
• When the System Audio Control function (page 51)
is activated, this setting may change automatically.
[Audio Settings]
x [BD Audio MIX Setting]
[On]: Outputs the audio obtained by mixing the
interactive audio and secondary audio to the
primary audio.
[Off]: Outputs the primary audio only. Select
this when outputting HD audio signals to an AV
receiver.
x [Sound Effect]
You can set the system’s sound effects (SOUND
MODE, “TONE,” “NIGHT MODE,” and
“SUR.SETTING”) to on/off.
x [Audio DRC]
You can compress the dynamic range of the
sound track.
[On]: Enables all of the system’s sound effects.
The upper limit of sampling frequency is set to
48 kHz.
[Auto]: Performs playback at the dynamic range
specified by the disc (BD-ROM only).
[Off]: No compression of dynamic range.
[Off]: The sound effects are disabled. Select this
when you do not want to set the upper limit of
sampling frequency.
US
61
Download from Www.Somanuals.com. All Manuals Search And Download.
x [Speaker Settings]
x [BD Internet Connection]
To obtain the best possible surround sound, set
the speakers. For details, see “Setting the
[Allow]: Normally select this.
[Do not allow]: Prohibits Internet connection.
x [BD Data Jack Selection]
[Internal memory]: Selects the internal memory
to store BD data.
x [Auto Calibration]
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
[USB device (front)]: Selects the
on the front panel to store BD data.
[USB device (rear)]: Selects the
on the rear panel to store BD data.
(USB) port
(USB) port
[BD/DVD Viewing
Settings]
You can make detailed settings for BD/DVD
playback.
[Parental Control
Settings]
x [Password]
x [BD/DVD Menu]
Set or change the password for the Parental
Control function. A password allows you to set
a restriction on BD-ROM, DVD VIDEO, or
Internet video playback. If necessary, you can
differentiate the restriction levels for
BD-ROMs, DVD VIDEOs, and Internet videos.
You can select the default menu language for
BD-ROMs or DVD VIDEOs.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
x [Parental Control Area Code]
x [Audio]
Playback of some BD-ROMs or DVD VIDEOs
can be limited according to the geographic area.
Scenes may be blocked or replaced with
different scenes. Follow the on-screen
You can select the default track language for
BD-ROMs or DVD VIDEOs.
When you select [Original], the language given
priority in the disc is selected.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
instructions and enter your four-digit password.
x [BD Parental Control]
Playback of some BD-ROMs can be limited
according to the age of the users. Scenes may be
blocked or replaced with different scenes.
Follow the on-screen instructions and enter your
four-digit password.
x [Subtitle]
You can select the default subtitle language for
BD-ROMs or DVD VIDEOs.
When you select [Select Language Code], the
display for entering the language code appears.
Enter the code for your language by referring to
x [DVD Parental Control]
Playback of some DVD VIDEOs can be limited
according to a predetermined level such as the
age of the users. Scenes may be blocked or
replaced with different scenes. Follow the on-
screen instructions and enter your four-digit
password.
x [BD Hybrid Disc Playback Layer]
[BD]: Plays BD layer.
[DVD/CD]: Plays DVD or CD layer.
US
62
Download from Www.Somanuals.com. All Manuals Search And Download.
[Mode]: You can enjoy the system’s sound in
another room.
[Standby]: You can enjoy the S-AIR receiver
while the unit is in standby mode.
x [Internet Video Parental Control]
Playback of some Internet videos can be limited
according to the age of the users. Scenes may be
blocked or replaced with different scenes.
Follow the on-screen instructions and enter your
four-digit password.
x [Dimmer]
[Bright]: Bright lighting.
[Dark]: Low lighting.
x [Internet Video Unrated]
[Allow]: Allows the playback of unrated
Internet videos.
[Block]: Blocks the playback of unrated Internet
videos.
x [HDMI Settings]
By connecting Sony components that are
compatible with the Control for HDMI function
with an HDMI cable, operation is simplified.
For details, see “Using the Control for HDMI
[Control for HDMI]
You can set the [Control for HDMI] function to
[Music Settings]
You can make detailed settings for Super Audio
on/off.
CD playback.
[On]: On. You can operate mutually between
components that are connected with an HDMI
cable.
[Off]: Off.
x [Super Audio CD Playback Layer]
[Super Audio CD]: Plays the Super Audio CD
layer.
[Audio Return Channel]
[CD]: Plays the CD layer.
This function is available when you connect the
system and TV that is compatible with the Audio
Return Channel function.
[Auto]: The system can receive the digital audio
signal of the TV automatically via an HDMI
cable.
x [Super Audio CD Playback Channel]
[DSD 2ch]: Plays the 2ch area.
[DSD Multi]: Plays the multi-channel area.
[Off]: Off.
Note
[System Settings]
You can make the system-related settings.
• This function is available only when [Control for
HDMI] is set to [On].
[Volume Limit]
x [OSD]
activated, loud sound may be output depending
on the volume level of the system. You can
prevent this by limiting the maximum level of
the volume when the System Audio Control
function activates.
[Level3]: Maximum volume level is set to 15.
[Level2]: Maximum volume level is set to 20.
[Level1]: Maximum volume level is set to 30.
[Off]: Off.
You can select your language for the system on-
screen displays.
x [S-AIR Settings]
You can set up the S-AIR settings. For details,
[Info]: The selected S-AIR ID is displayed.
[Pairing]: You can pair the system and S-AIR
sub unit, such as a surround amplifier or S-AIR
receiver.
Note
[RF Change]: If wireless transmission is
unstable, set this function.
• This function is available only when [Control for
HDMI] is set to [On].
US
63
Download from Www.Somanuals.com. All Manuals Search And Download.
When the registration is disabled
[Registration Code]: The registration code is
displayed.
[Deregistration Code]: The deregistration code
is displayed. (This item can be selected only
after the registration code is displayed.)
x [Quick Start Mode]
[On]: Shortens the startup time from standby
mode. You can operate the system quickly after
turning it on.
[Off]: The default setting.
When the registration is enabled
x [Auto Standby]
Press C/c to select [OK] or [Cancel], then
[On]: Turns on the [Auto Standby] function.
When you do not operate the system for about
30 minutes, the system enters standby mode
automatically.
press
.
[OK]: The device is deregistered and the
deregistration code is displayed.
[Cancel]: The system returns to the previous
display.
[Off]: Turns off the function.
Note
• This function does not work while the sleep timer is
set.
For more information, go to
x [Auto Display]
x [System Information]
You can display the system’s software version
information and the MAC address.
[On]: Automatically displays information on the
screen when changing the viewing titles, picture
modes, audio signals, etc.
[Off]: Displays information only when you
press DISPLAY.
[Network Settings]
You can make detailed settings for Internet and
x [Screen Saver]
[On]: Turns on the screen saver function.
[Off]: Off.
network.
x [Software Update Notification]
[On]: Sets the system to inform you of newer
[Off]: Off.
x [Internet Settings]
Connect the system to the network beforehand.
For details, see “Step 3: Connecting to the
x [Gracenote Settings]
[View Network Status]: Displays the current
network status.
[Wired Setup]: Select this when you connect to
a broadband router directly.
[USB Wireless Setup]: Select this when you use
a USB Wireless LAN Adapter.
[Auto]: Automatically downloads disc
information when you stop playback of the disc.
To download, the system must be connected to
the network.
[Manual]: Downloads disc information when
you select [Playback History List] or
[Information Display] in the options menu.
For more information, go to
x [DivX® VOD]
x [Network Connection Diagnostics]
You can run the network diagnostics to check if
the network connection has been made properly.
(Except for U.S. models)
You can display the registration or
deregistration code for this system, or deregister
this system after registration.
US
64
Download from Www.Somanuals.com. All Manuals Search And Download.
x [Connection Server Settings]
Sets whether or not to display the connected
DLNA server.
x [BD Remote Device Registration]
Registers your “BD remote” device.
x [Registered BD Remote Devices]
Displays a list of your registered “BD remote”
devices.
[Easy Setup]
Re-runs the Easy Setup to make the basic
settings. Follow the on-screen instructions.
[Resetting]
x [Reset to Factory Default Settings]
You can reset the system settings to the factory
default by selecting the group of settings. All the
settings within the group will be reset.
x [Initialize Personal Information]
You can erase your personal information stored
in the system.
US
65
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not place the system in a place where medical
equipment is in use. It may cause a malfunction of
medical equipment (BDV-HZ970W only).
• If you use a pacemaker or other medical device,
consult your physician or the manufacturer of your
medical device before using the wireless LAN
function (BDV-HZ970W only).
Additional Information
Precautions
On safety
• To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the system, or
place the system near water, such as near a bathtub or
shower room. Should any solid object or liquid fall
into the cabinet, unplug the system and have it
checked by qualified personnel before operating it
any further.
On operation
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the unit. Should
this occur, the system may not operate properly. In
this case, remove the disc and leave the system turned
on for about half an hour until the moisture
evaporates.
• Do not touch the AC power cord (mains lead) with
wet hands. Doing so may cause an electric shock.
• When you move the system, take out any disc. If you
do not, the disc may be damaged.
On power sources
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
• Unplug the unit from the wall outlet (mains) if you do
not intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
On adjusting volume
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
On placement
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the system in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the system can overheat and malfunction.
• Do not place the system on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that may
block the ventilation slots.
On cleaning
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
• Do not install the system in a confined space, such as
a bookshelf or similar unit.
• Do not install the system near heat sources such as
radiators, air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
On replacement of parts
• In the events that this system is repaired, repaired
parts may be collected for reuse or recycling
purposes.
• Do not install the system in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the system and discs away from components
with strong magnets, such as microwave ovens, or
large loudspeakers.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
• Do not place heavy objects on the system.
• Do not place metal objects in front of the front panel.
They may limit reception of radio waves (BDV-
HZ970W only).
US
66
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
• Do not stick paper or tape on the disc.
On moving the system
• Before moving the system, make sure that there is no
disc inserted, and remove the AC power cord (mains
lead) from the wall outlet (mains).
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
About S-AIR function
• As the S-AIR products transmit sound by radio
waves, sound may skip when radio waves are
obstructed. This is a characteristic of radio waves and
is not malfunction.
• After playing, store the disc in its case.
• As the S-AIR products transmit sound by radio
waves, equipment that generates electromagnetic
energy, such as a microwave oven, may prevent
wireless transmission.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
• As the S-AIR products use the radio waves that share
the same frequency as other wireless systems, such as
wireless LAN or Bluetooth devices, interference or
poor transmission may occur. In this case, take the
following steps to enhance the transmission of
signals:
Wipe the disc from the center out.
– Avoid placing the S-AIR products near other
wireless systems.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
– Avoid using the S-AIR products and the other
wireless systems simultaneously.
– The transmission may be improved by changing
the transmission channel (frequency) of the other
wireless system(s). For details, refer to the
operating instructions of the other wireless
system(s).
This system can only play a standard circular
disc. Using neither standard nor circular discs
(e.g., card, heart, or star shape) may cause a
malfunction.
• The transmission distance differs depending on the
usage environment. Find locations where
transmission between the S-AIR main unit and sub
unit is most effective, and install the S-AIR main unit
and sub unit there.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
• Place the S-AIR products on a stable surface.
• Poor transmission may occur and the transmission
distance may be too short if the following conditions
exist:
– There is a wall/floor made of reinforced concrete
or stone between the S-AIR products.
– There is an iron divider/door or furniture/electric
product made of fireproof glass, metal, etc.,
between the S-AIR products.
US
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your
nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
In the event of a problem with the S-AIR function, have a Sony dealer check the entire system together
(S-AIR main unit and sub unit).
Power
Symptom
Problems and solutions
The power is not turned on.
“PROTECTOR” and “PUSH
• Check that the AC power cord (mains lead) is connected securely.
Press "/1 to turn off the system, and check the following items after
POWER” appear alternately in “STANDBY” disappears.
the front panel display.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If
the cause of the problem cannot be found even after checking all the above
items, consult your nearest Sony dealer.
General
Symptom
Problems and solutions
The remote does not function.
• The distance between the remote and the unit is too far.
• The batteries in the remote are weak.
• When you cannot perform menu operations via the front panel display, press
HOME on the remote.
The system does not work
normally.
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then
reconnect after several minutes.
Picture
Symptom
Problems and solutions
There is no picture.
• The video input on the TV is not set so that you can view pictures from the
system.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
• When playing a double-layer DVD, the video and audio may be momentarily
interrupted at the point where the layers switch.
3D images from the HDMI (IN • Depending on the TV or video component, 3D images may not appear.
1) or HDMI (IN 2) jack do not
appear on the TV screen.
US
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
No picture appears when the
• Press and hold N and VOLUME – on the unit for more than 5 seconds to reset
video output resolution selected the video output resolution to the lowest resolution.
in [Output Video Format] is
incorrect.
Video signals are only output
from the HDMI (OUT) jack
when connecting the HDMI
(OUT) jack and other video
output jacks at the same time.
• Set [Output Video Format] in [Screen Settings] to [Component Video]
dark/the bright area is too bright
or unnatural.
The picture is not output
correctly.
• If the analog and digital signals are output at the same time, set [BD/DVD-
• For BD-ROMs, check the [BD/DVD-ROM 1080/24p Output] settings in
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your system goes through your VCR to get to your
TV, the copy-protection signal applied to some BD/DVD programs could affect
picture quality. If you still experience problems even when you connect your
unit directly to your TV, try connecting your unit to the other input jacks.
Even though you set the aspect • The aspect ratio on the disc is fixed.
ratio in [TV Type] of [Screen
Settings], the picture does not fill
the TV screen.
Color irregularity occurs on the • If the speakers are used with a CRT-based TV or projector, install the speakers
TV screen.
at least 1.0 ft (0.3 meters) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15
to 30 minutes.
• Make sure that no magnetic object (magnetic latch on a TV stand, health care
device, toy, etc.) is placed near the speakers.
Sound
Symptom
Problems and solutions
There is no sound.
• The speaker cord is not connected securely.
• Fast forward or fast reverse is performed. Press N to return to normal play
mode.
• Slow forward or freeze frame is performed. Press N to return to normal play
mode.
No sound is output from the
HDMI OUT jack.
The Super Audio CD sound of a • HDMI (IN 1) and HDMI (IN 2) does not accept an audio format that contains
component that is connected to
the HDMI (IN 1) or HDMI (IN
2) jack is not output.
copy protection. Connect the analog audio output of the component to the
AUDIO (AUDIO IN L/R) jacks of the unit.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components are connected correctly and securely.
US
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
There is no sound from the
subwoofer.
There is no digital sound from
the HDMI (OUT) jack when
• Set [Control for HDMI] in [HDMI Settings] of [System Settings] to [On]
(page 63). Also, set [Audio Return Channel] in [HDMI Settings] of [System
function.
• Make sure that your TV is compatible with the Audio Return Channel function.
• Make sure that an HDMI cable is connected to a jack on your TV that is
compatible with the Audio Return Channel function.
• The sampling frequency of the input stream is more than 48 kHz.
The system does not output
• Set [Audio Return Channel] in [HDMI Settings] of [System Settings] to [Off]
to a set-top box.
Severe hum or noise is heard.
• Check that the connecting cords are away from a transformer or motor, and at
least 10 feet (3 meters) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• Clean the disc.
The sound loses stereo effect
when you play a CD.
hear when you are playing a
sound track of Dolby Digital,
DTS, or MPEG audio.
• Depending on the BD/DVD, the output signal may not be the entire 5.1 channel.
It may be monaural or stereo even if the sound track is recorded in Dolby
Digital or MPEG audio format.
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.
speaker only.
No sound is heard from the
center speaker.
• Depending on the source, the effect of the center speaker may be less
noticeable.
• A 2 channel source is being played.
No sound or only a very low-
level sound is heard from the
surround speakers.
• Depending on the source, the effect of the surround speakers may be less
noticeable.
• A 2 channel source is being played.
off.
The sound effects are disabled. • The effects of SOUND MODE, “TONE,” “NIGHT MODE,” and
Distortion occurs in the sound of • Reduce the input level for the connected component by setting [Attenuate -
a connected component.
US
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
There is no sound from the
surround speakers or surround
back speakers.
Check the status of the S-AIR/STANDBY indicator on the surround amplifier.
• Turns off.
– Check that the AC power cord (mains lead) of the surround amplifier is
connected securely.
– Turn the surround amplifier on by pressing "/1 on the surround amplifier.
• Flashes orange.
– Check that the wireless transceiver is inserted into the surround amplifier
• Flashes green quickly.
– Set the SURROUND SELECTOR switch of the surround amplifier to
SURROUND (page 29).
– If there is no sound from the surround back speakers, set [Surround Back] in
• Flashes red.
– Press "/1 to turn off the surround amplifier, and check the following items.
1Are the + and – speaker cords short-circuited?
2Is anything blocking the ventilation holes of the surround amplifier?
After checking the above items and fixing any problems, turn on the
surround amplifier. If the cause of the problem cannot be found even after
checking all the above items, consult your nearest Sony dealer.
• Flashes green slowly or turns red.
– Sound transmission is poor. Move the surround amplifier so that the S-AIR/
STANDBY indicator turns green.
– Move the system away from other wireless devices.
– Avoid using any other wireless devices.
• Turns green.
– The speaker cord is not connected securely.
– Check the speaker connections and settings.
– Depending on the source or the settings of the S-AIR main unit, the effect of
the speakers may be less noticeable.
Operation
Symptom
Problems and solutions
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna
in.
(aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic
tuning). Use direct tuning.
The disc does not play.
• You are attempting to play a disc with a format that cannot be played back by
• The region code on the BD/DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
US
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
File names are not displayed
correctly.
• The system can only display ISO 8859-1-compliant character formats. Other
character formats may be displayed differently.
• Depending on the writing software used, the input characters may be displayed
differently.
A disc does not start playing
from the beginning.
• Resume play has been selected. Press OPTIONS and select [Play from
beginning], then press
• The title or BD/DVD menu automatically appears on the TV screen.
Playback does not start from the • The resume point may be cleared from memory depending on the disc when
.
resume point where you last
stopped playing.
– you open the disc tray.
– you disconnect the USB device.
– you play other content.
– you turn off the unit.
The system starts playing the
disc automatically.
• The BD/DVD features an auto playback function.
Playback stops automatically.
• Some discs may contain an auto pause signal. While playing such a disc, the
system stops playback at the auto pause signal.
You cannot perform some
• Depending on the disc, you may not be able to perform some of the operations.
functions such as stop or search. Refer to the operating instructions supplied with the disc.
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in
TV screen in the language you
want.
The language for the soundtrack/ • Try using the BD’s or DVD’s menu.
subtitle or angles cannot be
changed.
• Multi-lingual tracks/subtitles or multi-angles are not recorded on the BD or
DVD being played.
• The BD or DVD prohibits the changing of the language for the sound track/
subtitle or angles.
The disc tray does not open and • Try the following: 1 Press and hold N and Z on the unit for more than 5
you cannot remove the disc even seconds to open the disc tray. 2 Remove the disc. 3 Disconnect the AC power
after you press Z.
cord (mains lead) from the wall outlet (mains), then reconnect after several
minutes.
A disc cannot be ejected and
“LOCKED” appears in the front
panel display.
• Contact your Sony dealer or local authorized Sony service facility.
The Control for HDMI function • Set [Control for HDMI] in [HDMI Settings] of [System Settings] to [On]
does not work.
• Make sure that the connected component is compatible with the [Control for
HDMI] function.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power
cord (mains lead), or have a power failure, set [Control for HDMI] in [HDMI
Settings] of [System Settings] to [Off], then set [Control for HDMI] to [On]
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
No sound is output from the
system and TV while using the
System Audio Control function.
• Make sure that the connected TV is compatible with the System Audio Control
function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
US
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
Bonus contents or other data that • Try the following: 1 Remove the disc. 2 Turn the system off. 3 Remove and
are contained in a BD-ROM
cannot be played.
ROM with BONUSVIEW/BD-LIVE.
The unit does not work and
“CHILD LOCK” appears in the
front panel display when you
press any button on the unit.
The system menu does not work. • Press HOME on the remote.
USB device
Symptom
Problems and solutions
The USB device is not
recognized.
• Try the following: 1 Turn the system off. 2 Remove and reconnect the USB
device. 3 Turn the system on.
• Make sure that the USB device is securely connected to the
• Check if the USB device or a cable is damaged.
• Check if the USB device is on.
(USB) port.
• If the USB device is connected via a USB hub, disconnect it and connect the
USB device directly to the unit.
S-AIR
Symptom
Problems and solutions
Wireless transmission is not
activated. (The indicator of the
S-AIR sub unit flashes green
slowly or turns red.)
• Check that the wireless transceiver is inserted correctly into the unit and S-AIR
• Sound transmission is poor. Move the S-AIR sub unit so that the indicator turns
green.
• Move the system away from other wireless devices.
• Avoid using any other wireless devices.
There is no sound from the
S-AIR sub unit, noise is heard
from the S-AIR sub unit, or
sound from the S-AIR sub unit
skips.
• If you use another S-AIR main unit, place it more than 25 feet (8 meters) away
from the unit.
• Place the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Place the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then turn them on.
BRAVIA Internet Video
Symptom
Problems and solutions
The picture/sound is poor/certain • Picture/sound quality may be poor depending on Internet content providers.
programs display with a loss of
detail, especially during fast-
motion or dark scenes.
• Picture/sound quality may be improved by changing the connection speed.
Sony recommends a connection speed of at least 2.5 Mbps for standard-
definition video and 10 Mbps for high-definition video.
• Not all videos contain sound.
US
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Problems and solutions
The picture is small.
• Press X to zoom in.
Network connection
Symptom
Problems and solutions
The system cannot connect to the • Check the network connection (page 28) and the network settings (page 64).
network.
You cannot connect your PC to • The wireless settings of the router may change automatically if you use the Wi-
the Internet after [Wi-Fi
Protected Setup (WPS)] is
performed.
Fi Protected Setup function before adjusting the settings of the router. In this
case, change the wireless settings of your PC accordingly.
You cannot connect the system • Check if the wireless LAN router is on.
to your wireless LAN router.
• Depending on the usage environment, including the wall material, radio wave
reception conditions, or obstacles between the system and the wireless LAN
router, the possible communication distance may be shortened. Move the
system and the wireless LAN router closer to each other.
• Devices that use a 2.4 GHz frequency band, such as a microwave, Bluetooth, or
digital cordless device, may interrupt the communication. Move the unit away
from such devices, or turn off such devices.
The desired wireless router is not • Press RETURN to return to the previous screen, and try [Scan] again. If the
detected even if [Scan] is
performed.
desired wireless router is still not detected, press RETURN to select [Manual
registration].
The message [A new software
version has been found on the
network. Perform update under
“Network Update.”] appears on
the screen when turning the
system on.
version.
USB Wireless LAN Adapter
(BDV-HZ970W only)
Symptom
Problems and solutions
The system cannot connect to the • The distance between the unit and the wireless LAN router is too far (page 28).
network or the network
connection is unstable.
• Change the USB Wireless LAN Adapter position.
• Set [RF Change] in [S-AIR Settings] of [System Settings] to [Off], and change
Other
Symptom
Problems and solutions
“Exxxx” appears in the front
panel display.
• Contact your nearest Sony dealer or local authorized Sony service facility and
give the error code.
US
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on playback operations of a
BD/DVD
Some playback operations of a BD/DVD may be
intentionally set by software producers. Since
this system plays a BD/DVD according to the
disc contents the software producers designed,
some playback features may not be available.
Playable Discs
1)
Blu-ray Disc
BD-ROM
2)
2)
BD-R /BD-RE
3)
DVD
DVD-ROM
DVD-R/DVD-RW
DVD+R/DVD+RW
Note about double-layer BDs/
DVDs
The playback picture and sound may be
3)
CD
CD-DA (Music CD)
CD-ROM
momentarily interrupted when the layers switch.
CD-R/CD-RW
Super Audio CD
Region code (BD-ROM/DVD
VIDEO only)
1)Since the Blu-ray Disc specifications are new and
evolving, some discs may not be playable depending
on the disc type and the version. Also, the audio
output differs depending on the source, connected
output jack, and selected audio settings.
2)BD-RE: Ver.2.1
Your system has a region code printed on the
rear of the unit and will only play a BD-ROM/
DVD VIDEO (playback only) labeled with
ALL
identical region codes or
.
BD-R: Ver.1.1, 1.2, 1.3 including organic pigment
type BD-R (LTH type)
BD-Rs recorded on a PC cannot be played if
postscripts are recordable.
3)A CD or DVD disc will not play if it has not been
correctly finalized. For more information, refer to the
operating instructions supplied with the recording
device.
Discs that cannot be played
• BDs with cartridge
• DVD-RAMs
• HD DVDs
• DVD Audio discs
• PHOTO CDs
• Data part of CD-Extras
• VCDs/Super VCDs
• Audio material side on DualDiscs
• A disc recorded in a color system other than
NTSC, such as PAL (this system conforms to
the NTSC color system).
Notes on discs
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
DualDiscs and some music discs encoded with
copyright protection technologies do not
conform to the Compact Disc (CD) standard.
Therefore, these discs may not be compatible
with this product.
US
75
Download from Www.Somanuals.com. All Manuals Search And Download.
6)The system plays SD resolution only via the DLNA
function.
Playable Types of Files
Note
• Some files may not play depending on the file format,
the file encoding, the recording condition, or DLNA
server condition.
Video
File format
Extensions
1)5)
• Some files edited on a PC may not play.
• The system can recognize the following files or
folders in BDs, DVDs, CDs and USB devices:
– up to folders in the 5th tree
MPEG-1 Video/PS
“.mpg,” “.mpeg,” “.m2ts,”
“.mts”
MPEG-2 Video/PS,
1)6)
TS
2)
DivX
“.avi,” “.divx”
– up to 500 files in a single tree
1)5)
MPEG4/AVC
“.mkv,” “.mp4,” “.m4v,”
“.m2ts,” “.mts”
• The system can recognize the following files or
folders stored in the DLNA server:
1)5)
WMV9
“.wmv,” “.asf”
3)
– up to folders in the 20th tree
5)
AVCHD
– up to 999 files in a single tree
• Some USB devices may not work with this system.
• The system can recognize Mass Storage Class (MSC)
devices (such as flash memory or an HDD) that are
FAT-compatible and non-partitioned, Still Image
Capture Devices (SICDs), and 101-key keyboards
Music
File format
Extensions
MP3 (MPEG-1 Audio
Layer III)
“.mp3”
(front
(USB) port only).
1)4)6)
AAC
“.m4a”
“.wma”
“.wav”
• To avoid data corruption or damage to USB memory
or other devices, turn the system off before
connecting or removing USB memory or other
devices.
1)4)
WMA9 Standard
LPCM
• The system may not play high bit rate video files from
a DATA CD smoothly. It is recommended to play
high bit rate video files using a DATA DVD.
Photo
File format
Extensions
JPEG
“.jpg,” “.jpeg,” “.jpe”
1)The system does not play files encoded with DRM.
2) Canadian models only
®
ABOUT DIVX VIDEO: DivX is a digital video
format created by DivX, Inc. This is an official DivX
Certified device that plays DivX video. Visit
tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
®
Certified device must be registered in order to play
DivX Video-on-Demand (VOD) content. To
generate the registration code, locate the DivX VOD
section in the device setup menu. Go to
vod.divx.com with this code to complete the
registration process and learn more about DivX
VOD.
3)The system plays AVCHD-format files that are
recorded via a digital video camera, etc. To watch
AVCHD-format files, the disc with AVCHD-format
files on it must be finalized.
4)The system does not play files encoded with
Lossless, etc.
5)The system does not play these files via the DLNA
function.
US
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Audio Formats
Audio formats supported by this system are as follows.
Format
LPCM 2ch
LPCM 5.1ch,
LPCM 7.1ch
Dolby Digital Dolby
TrueHD,
DTS
DTS-ES
Discrete 6.1,
DTS-ES
Matrix 6.1,
DTS96/24
DTS-HD
High
Resolution
Audio
DTS-HD
Master
Audio
Function
DolbyDigital
Plus
“BD/DVD”
a
a
a
a
a
a
a
a
a
a
a
a
“HDMI (IN 1)”
“HDMI (IN 2)”
–
–
–
–
“SAT/CABLE”
“TV”
a
–
a
–
a
–
–
–
(DIGITAL IN)
a: Supported format.
–: Unsupported format.
Note
• HDMI (IN 1) and HDMI (IN 2) do not input sound in the case of an audio format that contains copy protections
such as Super Audio CD or DVD-Audio.
Video Output Resolution
Output resolution differs depending on the [Output Video Format] setting in [Screen Settings]
When [Output Video Format] is set to
[HDMI]
When [Output Video Format] is set to
[Component Video]
Resolution
setting
COMPONENT
COMPONENT
VIDEO OUT
jack
HDMI OUT
VIDEO OUT
jack
HDMI OUT
VIDEO OUT
jacks
VIDEO OUT
jacks
jack
jack
480i
480i
480i
480i
480i
480i
480i
480p
480i
480p
720p
1080i
1080p
480i
480i
480i
480p
480i
480p
480p
720p
1080i
1080p
720p*
1080i*
1080i*
480i
720p*
720p
480i
1080i*
1080i
unselectable
unselectable
unselectable
* Protected contents on DVDs are output at 480p resolution.
When [Output Video Format] is set to [Video]
480i video signals are output from the VIDEO OUT or COMPONENT VIDEO OUT jack, and 480p
video signals are output from the HDMI OUT jack.
US
77
Download from Www.Somanuals.com. All Manuals Search And Download.
1920 × 1080i@50 Hz
1920 × 1080p@50 Hz
1920 × 1080p@24 Hz
Specifications
Amplifier Section
BD/DVD/Super Audio CD/CD System
Signal format system
NTSC
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC
USB Section
DISTORTION:
(FTC)
Front L + Front R:
(USB) port:
Type A (For connecting
USB memory, memory
card reader, digital still
camera, and digital video
camera)
With 3 ohms loads, both
channels driven, from
180 Hz - 20,000 Hz; rated
60 W per channel
Maximum current:
500 mA
minimum RMS power,
with no more than 1% total
harmonic distortion from
250 milli watts to rated
output.
LAN Section
LAN (100) terminal
100BASE-TX Terminal
Tuner Section
System
PLL quartz-locked digital
synthesizer
Other models:
POWER OUTPUT (rated)
Front L + Front R:
FM tuner section
Tuning range
105 W + 105 W (at 3 ohms,
1 kHz, 1% THD)
87.5 MHz - 108.0 MHz
(100 kHz step)
POWER OUTPUT (reference)
Front L/Front R/Center: 167 W (per channel at 3
ohms, 1 kHz)
Antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
FM wire antenna (aerial)
10.7 MHz
Subwoofer:
165 W (at 3 ohms, 80 Hz)
Speakers
Inputs (Analog)
AUDIO (AUDIO IN)
Inputs (Digital)
DIGITAL IN (SAT/CABLE COAX), DIGITAL IN
(TV OPT)
Sensitivity: 450/250 mV
Front (SS-TSB102) for BDV-HZ970W
Speaker system
Speaker unit
Full range Bass reflex
55 mm × 80 mm (2 1/4 in ×
3 1/4 in) cone type
Supported formats: LPCM
2CH (up to 48 kHz), Dolby
Digital, DTS
Rated impedance
Dimensions (approx.)
3 ohms
75 mm × 610 mm × 70 mm
(3 in × 24 1/16 in × 2 7/8 in)
(w/h/d) (wall-mounted
part)
Floor: 250 mm × 1,000
mm × 250 mm (9 7/8 in ×
39 3/8 in × 9 7/8 in) (w/h/d)
(whole speaker)
Desktop: 250 mm × 727
mm × 250 mm (9 7/8 in ×
28 5/8 in × 9 7/8 in) (w/h/d)
(whole speaker)
0.9 kg (2 lb) (wall-
mounted part)
Video Section
Outputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
HDMI Section
Connector
Video inputs
Type A (19pin)
HDMI (IN 1), HDMI (IN
2):
640 × 480p@60 Hz
720 × [email protected]/60 Hz
720 × [email protected]/60 Hz
1280 × [email protected]/60 Hz
1920 × [email protected]/
60 Hz
Mass (approx.)
Floor: 2.0 kg (4 lb 7 oz)
(whole speaker)
Desktop: 1.9 kg (4 lb 3 oz)
(whole speaker)
1920 × [email protected]/
60 Hz
720 × 576i@50 Hz
720 × 576p@50 Hz
1280 × 720p@50 Hz
US
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround (SS-TSB101) for BDV-HZ970W
Subwoofer (SS-WSB102) for BDV-HZ970W
Speaker system
Speaker unit
Full range Bass reflex
55 mm × 80 mm (2 1/4 in ×
3 1/4 in) cone type
3 ohms
75 mm × 225 mm × 71 mm
(3 in × 8 7/8 in × 2 7/8 in)
(w/h/d)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Subwoofer Bass reflex
180 mm (7 1/8 in) cone type
3 ohms
275 mm × 405 mm × 275
mm (10 7/8 in × 16 in ×
10 7/8 in) (w/h/d)
Rated impedance
Dimensions (approx.)
Mass (approx.)
7.5 kg (16 lb 12 oz)
Mass (approx.)
0.45 kg (1 lb)
Subwoofer (SS-WSIZ1) for BDV-IZ1000W
Front/Surround (SS-TSIZ1) for BDV-
IZ1000W
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Subwoofer Bass reflex
180 mm (7 1/8 in) cone type
3 ohms
275 mm × 405 mm × 275
mm (10 7/8 in × 16 in ×
10 7/8 in) (w/h/d)
Speaker system
2-Way 2-Driver speaker
system, Bass reflex
Speaker unit
Tweeter:
Woofer:
20 mm (3/4 in) cone type
40 mm × 70 mm (1 9/16 in ×
2 3/4 in) cone type
3 ohms
Mass (approx.)
7.5 kg (16 lb 12 oz)
General
Power requirements
Power consumption
Rated impedance
120 V AC, 60 Hz
On: 110 W
Dimensions (approx.)
Front speaker (after assembly):
200 mm × 1,100 mm ×
Standby: 0.3 W (at the
Power Saving mode)
430 mm × 83 mm × 355
mm (17 in × 3 3/8 in ×
14 1/8 in) (w/h/d) incl.
projecting parts such as the
wireless transceiver slot;
430 mm × 83 mm × 384
mm (17 in × 3 3/8 in ×
15 1/4 in) (w/h/d) incl. the
wireless transceiver
(EZW-RT10)
230 mm (7 7/8 in × 43 1/3 in
× 9 1/16 in) (w/h/d) (vertical
angle)
200 mm × 1,100 mm ×
255 mm (7 7/8 in × 43 1/3 in
× 10 in) (w/h/d) (upward
angle)
Dimensions (approx.)
Surround speaker (after assembly):
103 mm × 335 mm ×
103 mm (4 1/16 in × 13 3/16
in × 4 1/16 in) (w/h/d)
(vertical angle)
Mass (approx.)
5.3 kg (11 lb 11 oz)
Surround amplifier (TA-SA200WR)
Amplifier Section
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
103 mm × 356 mm ×
103 mm (4 1/16 in × 14 in ×
4 1/16 in) (w/h/d) (upward
angle)
(FTC)
With 3 ohms loads, both
channels driven, from 120
- 20,000 Hz; rated 45 watts
per channel minimum
RMS power, with no more
than 1% total harmonic
distortion from 250 milli
watts to rated output.
Mass (approx.)
Front speaker (after assembly):
2.9 kg (6 lb 6 oz)
Surround speaker (after assembly):
0.6 kg (1 lb 5 oz)
Center (SS-CTB101)
Speaker system
Full range Acoustic
suspension, Magnetically
Shielded
POWER OUTPUT (reference)
167 W (per channel at 3
Speaker unit
30 mm × 60 mm (1 3/16 in ×
2 3/8 in) cone type
3 ohms
ohms, 1 kHz)
3 - 16 Ω
Rated impedance
Rated impedance
Dimensions (approx.)
290 mm × 49 mm × 49 mm
(11 1/2 in × 1 15/16 in ×
1 15/16 in) (w/h/d)
0.28 kg (10 oz)
General
Power requirements
Power consumption
120 V AC, 60 Hz
On: 50 W
Mass (approx.)
US
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby power consumption
0.9 W (standby mode)
transmission products, the configuration of
products, the radio wave conditions, the line traffic,
and the products that you use. The transmission may
also be cut off depending on the radio wave
conditions. The standard values of the transmission
speed are the theoretical maximum values for the
wireless standards. They are not the actual speeds of
data transmission.
0.13 W (turned off)
206 mm × 60 mm × 256
mm (8 1/8 in × 2 3/8 in ×
10 1/8 in) (w/h/d) with the
wireless transceiver
inserted
Dimensions (approx.)
Mass (approx.)
1.3 kg (2 lb 14 oz)
Design and specifications are subject to change
without notice.
Wireless transceiver (EZW-RT10/EZW-
RT10A)
Communication system
S-AIR Specification
version 1.0
• Standby power consumption 0.3W (main unit),
0.13W (surround amplifier).
Frequency band
2.4000 GHz - 2.4835 GHz
DSSS
DC 3.3 V, 350 mA
50 mm × 13 mm × 60 mm
(2 in × 17/32 in × 2 3/8 in) (w/
h/d)
• Halogenated flame retardants are not used in the
certain printed wiring boards.
Modulation method
Power requirements
Dimensions (approx.)
• Over 85% power efficiency of amplifier block is
achieved with the full digital amplifier, S-Master.
Mass (approx.)
24 g (1 oz)
USB Wireless LAN Adapter (UWA-BR100)
Standards Compliance:
Host Interface:
Security:
IEEE 802.11a/b/g/n
USB 2.0
64/128 bit: WEP, WPA/
WPA2, WPS
Frequency and Channel*: 2.4 GHz - 2.4835 GHz
[CH1 - 11]
5.15 GHz - 5.25 GHz
[CH36 - 48]
5.25 GHz - 5.35 GHz
[CH52 - 64]
5.47 GHz - 5.725 GHz
[CH100 - 140]
5.725 GHz - 5.85 GHz
[CH149 - 165]
Data Rate**:
802.11a/g: 54, 48, 36, 24,
18, 12, 9 and 6 Mbps
802.11b: 11, 5.5, 2 and 1
Mbps
802.11n: up to 300 Mbps
(40 MHz/spatial streams:
2)
Power consumption:
Mass (Approx.):
Tx: up to 500 mA
USB Wireless LAN
Adapter: 27 g (1 oz)
Dimensions (Approx.) (w × h × d):
USB Wireless LAN
Adapter: 96 mm × 14 mm
× 27 mm (3 7/8 in × 9/16 in ×
1 1/8 in)
* The frequency and channel differ depending on the
area.
**The transmission speed differs depending on the
distance and number of obstructions between the
US
80
Download from Www.Somanuals.com. All Manuals Search And Download.
BD-ROM
BD-ROMs (Blu-ray Disc Read-Only Memory)
are commercially produced discs and are
available in the same capacities as the BD
below. Other than conventional movie and video
contents, these discs have enhanced features
such as interactive content, menu operations
using pop-up menus, selection of subtitle
display, and slideshow. Although a BD-ROM
may contain any form of data, most BD-ROM
discs will contain movies in High Definition
format, for playback on Blu-ray Disc/DVD
players.
Glossary
AVCHD
The AVCHD format is a high-definition digital
video camera format used to record SD
(standard definition) or HD (high definition)
signals of either the 1080i specification* or the
720p specification** on DVDs, using efficient
data compression coding technology. The
MPEG-4 AVC/H.264 format is adopted to
compress video data, and the Dolby Digital or
Linear PCM system is used to compress audio
data. The MPEG-4 AVC/H.264 format is
capable of compressing images at higher
efficiency than that of the conventional image
compression format. The MPEG-4 AVC/H.264
format enables a high definition (HD) video
signal shot on a digital video camera recorder to
be recorded on DVD discs in the same way as it
would be for a standard definition (SD)
television signal.
Blu-ray Disc (BD)
A disc format developed for recording/playing
high-definition (HD) video (for HDTV, etc.),
and for storing large amounts of data. A single
layer Blu-ray Disc holds up to 25 GB, and a
dual-layer Blu-ray Disc holds up to 50 GB of
data.
Digital Cinema Auto Calibration
(D.C.A.C)
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjust the
speaker settings to your listening environment in
a short period of time.
* A high definition specification that utilizes 1080
effective scanning lines and the interlace format.
**A high definition specification that utilizes 720
effective scanning lines and the progressive format.
BD-J application
Dolby Digital
The BD-ROM format supports Java for
interactive functions.
“BD-J” offers content providers almost
unlimited functionality when creating
interactive BD-ROM titles.
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
BD-R
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
BD-R (Blu-ray Disc Recordable) is a
recordable, write-once Blu-ray Disc, available
in the same capacities as the BD below. Since
contents can be recorded and cannot be
overwritten, a BD-R can be used to archive
valuable data or store and distribute video
material.
BD-RE
Dolby Digital Plus
BD-RE (Blu-ray Disc Rewritable) is a
recordable and rewritable Blu-ray Disc,
available in the same capacities as the BD
below. The re-recordable feature makes
extensive editing and time-shifting applications
possible.
Developed as an extension to Dolby Digital, the
audio coding technology supports 7.1 multi-
channel surround sound.
US
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Dolby Pro Logic II
DTS-HD High Resolution Audio
Developed as an extension to DTS Digital
Surround format. It supports a maximum
sampling frequency of 96 kHz, and 7.1 multi-
channel surround.
DTS-HD High Resolution Audio has a
maximum transmission rate of 6 Mbps, with
lossy compression.
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
DTS-HD Master Audio
DTS-HD Master Audio has a maximum
transmission rate of 24.5 Mbps, and uses
lossless compression, and DTS-HD Master
Audio corresponds to a maximum sampling
frequency of 192 kHz, and maximum of 7.1ch.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
HD Digital Cinema Sound (HD-D.C.S.)
HD Digital Cinema Sound (HD-D.C.S.) is
Sony’s new innovative home theater technology
using the latest acoustic and digital signal
processing technologies. It is based on precise
response measurement data of a mastering
studio.
With HD-D.C.S., you are able to enjoy Blu-ray
and DVD movies at home with not only the high
quality of sound, but also the best sound
ambience, just as the movie’s sound engineer
intended in the mastering process.
Dolby TrueHD
Dolby TrueHD is a lossless coding technology
that supports up to 8 channels of multi-channel
surround sound for the next generation of optical
discs. The reproduced sound is true to the
original source bit-for-bit.
HDMI (High-Definition Multimedia
Interface)
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Content Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
DTS
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
includes a stereo rear channel and a discrete
subwoofer channel. DTS provides the same 5.1
discrete channels of high quality digital audio.
The good channel separation is realized due to
the all channel data being recorded discretely
and processed in digitally.
Interlace format
(Interlaced scanning)
The Interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice -
alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
DTS Neo:6
This technology converts 2 channels stereo
recorded audio for 7 channels playback. There
are two modes to select according to the
playback source or your preference, CINEMA
for movies, and MUSIC for stereo sources such
as music.
LTH (Low to High)
LTH is a recording system that supports organic
pigment type BD-R.
US
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental Control
range of ISM band (Industrial, Scientific, and
Medical band), such as wireless LANs and
Bluetooth applications.
A function of the BD/DVD to limit playback of
the disc by the age of the users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
24p True Cinema
Movies shot with a film camera consist of 24
frames per second.
Since conventional televisions (both CRT and
flat panels) display frames either at 1/60 or 1/50
second intervals, the 24 frames do not appear at
an even pace.
When connected to a TV with 24p capabilities,
the player displays each frame at 1/24 second
intervals — the same interval originally shot
with the film camera, thus faithfully reproducing
the original cinema image.
PhotoTV HD
“PhotoTV HD” allows for highly-detailed
pictures, and photo-like expression of subtle
textures and colors. By connecting Sony
“PhotoTV HD” compatible devices using an
HDMI cable, a whole new world of photos can
be enjoyed in breathtaking Full HD quality. For
instance, the delicate texture of the human skin,
flowers, sand and waves can now be displayed
on a large screen in beautiful photo-like quality.
Pop-up menu
An enhanced menu operation available on BD-
ROMs. The pop-up menu appears when POP
UP/MENU is pressed during playback, and can
be operated while playback is in progress.
Progressive format
(sequential scanning)
In contrast to the Interlace format, the
progressive format can reproduce 50 - 60 frames
per second by reproducing all scanning lines
(525 lines for the NTSC system). The overall
picture quality increases and still images, text
and horizontal lines appear sharper. This format
is compatible with the 525 or 625 progressive
format.
S-AIR
(Sony Audio Interactive Radio
frequency)
Recent times have seen the rapid spread of BD/
DVD media, digital broadcasting, and other
high-quality media.
To ensure that the subtle nuances of these high-
quality media are transmitted with no
deterioration, Sony has developed a technology
called “S-AIR” for the radio transmission of
digital audio signals with no compression, and
has incorporated this technology into the EZW-
RT10/EZW-RT10A/EZW-T100.
This technology transfers digital audio signals
with no compression using the 2.4 GHz band
US
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
N
DTS Neo
Network Connection
Diagnostics 64
A
O
P
E
F
B
BD Hybrid Disc Playback
Layer 62
G
Q
BD Remote Device
Registration 65
BD/DVD-ROM 1080/24p
Output 60
H
HDMI
R
HDMI (High-Definition
Multimedia Interface) 83
Registered BD Remote Devices
65
Remote Controller Setting
Guide 59
Reset to Factory Default
Settings 65
I
Initialize Personal Information
65
Internet Video Parental Control
63
S
C
L
D
M
US
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Audio CD Playback
Channel 63
Super Audio CD Playback
Layer 63
T
TV Screen Size Setting for 3D
60
U
W
US
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
The software of this system may be updated in the future. To find out details on any
Printed in Malaysia
(1)
Download from Www.Somanuals.com. All Manuals Search And Download.
|