2-697-465-11(2)
Multi Channel
AV Receiver
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the
serial number in the space provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Model No.
Serial No.
STR-DG1000
Sony Corporation Printed in Malaysia
©2006 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
For customers in the United
States
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
CAUTION
You are cautioned that any changes or modification
not expressly approved in this manual could void
your authority to operate this equipment.
Note to CATV system installer:
This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
(servicing) instructions in the
literature accompanying the
appliance.
2GB
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
• The instructions in this manual are for model STR-
DG1000. Check your model number by looking at
the lower right corner of the front panel.
• The instructions in this manual describe the
controls on the supplied remote. You can also use
the controls on the receiver if they have the same
or similar names as those on the remote.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
*
Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the
double-D symbol are trademarks of Dolby
Laboratories.
** Manufactured under license from Digital
Theater Systems, Inc. U.S. Pat.
No’s. 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535 and other U.S.
and world-wide patents issued and pending.
“DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24”
are trademarks of Digital Theater Systems, Inc.
Copyright 1996, 2003 Digital Theater Systems,
Inc. All Rights Reserved.
This receiver incorporates High-Definition
Multimedia Interface (HDMI™) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
XM is a registered trademark of XM Satellite Radio
Inc.
This product is manufactured under license from
Neural Audio Corporation.
Sony Corporation hereby grants the user a non-
exclusive, non-transferable, limited license right to
use this product under the US and foreign patents
pending and other related technology owned by
Neural Audio Corporation.
“Neural” and “Neural Audio” and “Neural
Surround” are trademarks of Neural Audio
Corporation.
3GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Calibrating the appropriate settings
(Auto Calibration menu) ....................... 71
7: Calibrating the appropriate settings
Enjoying Dolby Digital and DTS surround
sound (A.F.D. mode) ............................. 72
Selecting a pre-programmed sound field
(DCS) .................................................... 74
Using only the front speakers
(2CH STEREO) .................................... 76
Enjoying the surround effect at low volume
levels (NIGHT MODE) ........................ 76
Listening to the sound without any adjustment
(ANALOG DIRECT) ............................ 77
Adjusting the speaker levels and balance
(TEST TONE) ....................................... 78
Resetting sound fields
(AUTO CALIBRATION) ......................41
to the initial settings .............................. 79
Adjusting the level
(Level Settings menu) ............................58
Adjusting the equalizer
(EQ Settings menu) ...............................59
Settings for the surround sound
(Sur Settings menu) ...............................61
Settings for the tuner
(Tuner Settings menu) ...........................63
Settings for the audio
(Audio Settings menu) ...........................64
Settings for the video
(Video Settings menu) ...........................65
Settings for the speakers
(Speaker Settings menu) ........................66
Settings for the system
Displaying menus of the receiver on the TV
screen .................................................... 89
Switching between digital and analog audio
(INPUT MODE) ................................... 91
Listening to digital sound from other inputs
(DIGITAL ASSIGN) ............................ 92
Watching HDMI images from other inputs
(HDMI VIDEO ASSIGN) .................... 93
Watching component images from other
(System Settings menu) .........................70
(COMPONENT VIDEO ASSIGN) ...... 94
4GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the sound in another zone
(Zone 2 operations) ............................... 98
Operating each component using the
remote ................................................. 103
Performing several commands in sequence
automatically (Macro Play) ................. 107
Setting remote control codes that are not
stored in the commander ..................... 109
Clearing all the contents of the remote’s
memory ............................................... 111
5GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Description and location of parts
Front panel
To remove the cover
Name
Function
Press PUSH.
A POWER
Press to turn the
receiver on or off (page
When you remove the cover, keep it out of
reach from children.
B AUTO CAL MIC Connects to the
jack
supplied optimizer
microphone for the
Digital Cinema Auto
Calibration function
6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
C TONE MODE
TONE
Adjusts FRONT BASS
and FRONT TREBLE.
Press TONE MODE
repeatedly to select
BASS or TREBLE,
then turn TONE to
adjust the level (page
59).
K HDMI
Press to select input
source from the
component connected
to the HDMI IN jack
L PHONES jack Connects to
M SPEAKERS
Press to select A, B
D Remote sensor Receives signals from
(OFF/A/B/A+B) A+B, OFF of the front
remote commander.
E MEMORY/
Press to operate a tuner
(FM/AM/XM) (page
N VIDEO 3 IN/
Connect to a portable
ENTER
PORTABLE AV audio/videocomponent
IN jack
TUNING MODE
TUNING
such as a camcorder or
52).
F CATEGORY
Used when listening to
O MULTI
Lights up when multi-
channel audio signals
are decoded (page 51).
MODE
CHANNEL
DECODING
lamp
CATEGORY
+/–
G Display
The current status of
the selected component
or a list of selectable
items appears here
(page 8).
P INPUT
Turn to select the input
source to play back
window
SELECTOR
Q MASTER
Turn to adjust the
volume level of all
speakers at the same
H 2CH
A.F.D.
Press to select sound
VOLUME
MOVIE
MUSIC
I POWER
SELECT
Press POWER (ZONE)
to enable operations in
zone 2. Then press
SELECT, then INPUT
SELECTOR (qh) to
select a source input
J MULTI CH IN
Press to select the audio
input signal from the
component connected
to the MULTI
CHANNEL INPUT
7GB
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indicators on the display
Name
Function
Name
Function
A SW
Lights up when sub woofer
selection is set to “YES”
and the audio signal is
B Playback
channel
The letters (L, C, R, etc.)
indicate the channels being
played back. The boxes
around the letters vary to
show how the receiver
downmixes the source
sound (based on the speaker
settings).
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
indicators
output from the SUB
While this indicator lights
up, the receiver creates a
sub woofer signal based on
the L.F.E. signal in the disc
being played back or the
low frequency components
of the front channels.
L
R
C
SL
SR
S
Surround (monaural or the
surround components
obtained by Pro Logic
processing)
SBL
SBR
SB
Surround Back Left
Surround Back Right
Surround Back (the
surround back components
obtained by 6.1 channel
decoding)
Example:
Recording format (Front/
Surround): 3/2.1
Output channel: Surround
speakers are set to “NO.”
Sound Field: A.F.D. AUTO
SW
L
C
R
SL
SR
8GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
C ;DIGITAL Lights up when the receiver
I COAX
Lights up when INPUT
MODE is set to “AUTO”
and the source signal is a
digital signal being input
through the COAXIAL
jack, or when INPUT
MODE is set to “COAX”
(EX)
is decoding Dolby Digital
Surround signals. When the
receiver is decoding Dolby
Digital Surround EX
signals, “;DIGITAL EX”
also lights up. When
playing a Dolby Digital
format disc, be sure that you
have made digital
connections and that
INPUT MODE is not set to
J OPT
Lights up when INPUT
MODE is set to “AUTO”
and the source signal is a
digital signal being input
through the OPTICAL jack,
or when INPUT MODE is
D INPUT
Lights up constantly. Oneof
the input indicators also
lights up according to the
current input.
K ANALOG Lights up when INPUT
MODE is set to “AUTO”
and no digital signal is
being input through the
COAXIAL or OPTICAL
jacks, or when INPUT
MODE is set to
E AUTO
Lights up when INPUT
MODE is set to “AUTO”
F HDMI 1 2
Lights up when the receiver
recognizes a component
connected via an HDMI IN
“ANALOG,” or when the
ANALOG DIRECT
function is being used (page
91).
G DTS (-ES) Lights up when the receiver
is decoding DTS signals.
When the receiver is
L MULTI IN Lights up when MULTI IN
decoding DTS-ES signals,
“DTS-ES” also lights up.
When playing a DTS
format disc, be sure that you
have made digital
connections and that
INPUT MODE is not set to
M SB DEC
Lights up when surround
back sound decoding is
activated (page 62).
N XM
Lights up when XM Radio
O D.RANGE Lights up when dynamic
range compression is
H 96/24
Lights up when the receiver
is decoding DTS96/24 (96
kHz/24 bit).
activated (page 59).
P EQ
Lights up when the
equalizer is activated (page
59).
continued
9GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
Q CAT
Lights up when “ALL
CATEGORY” mode is
changed to “ONE
V NEO:6
Lights up when DTS Neo:6
Cinema/Music decoding is
CATEGORY” mode during
XM Radio operation (page
85).
W DISCRETE Lights up when DTS-ES
Discrete decoding is
R ZONE 2
S SLEEP
T L.F.E.
Lights up while operation in
zone 2 is being enabled.
X MATRIX
Lights up when DTS-ES
Matrix decoding is
Lights up when the sleep
Y SP-A/SP-B/ Lights up according to the
Lights up when the disc
being played back contains
an L.F.E. (Low Frequency
Effect) channel and the
L.F.E. channel signal is
actually being reproduced,
the bars underneath the
letters light up to indicate
the level. Since the L.F.E.
signal is not recorded in all
parts of the input signal the
bar indication will fluctuate
(and may turn off) during
playback.
SP-OFF
speaker system used (page
40).
“SP-OFF” lights up when
“SP-OFF” is selected or
headphones are connected.
Z PRESET
Lights up when TUNING
MODE is “PRESET.”
wj Tuner
Lights up when using the
receiver to tune in radio
indicators
wk MEMORY Lights up when a memory
function, such as Name
activated.
U ;PRO
Lights up when the receiver
LOGIC (II/ applies Pro Logic
wl VOLUME Displays the current
IIx)
processing to 2 channel
signals in order to output
the center and surround
channel signals. “;PRO
LOGIC II” also lights up
when the Pro Logic II
MOVIE/MUSIC/GAME
decoder is activated.
volume.
“;PRO LOGIC IIx” also
lights up when the Pro
Logic IIx MOVIE/MUSIC/
GAME decoder is activated
Note
This indicator does not light if
both the center and surround
speakers are set to “NO” (page
67).
10GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
A AUDIO INPUT/OUTPUT section
C ANTENNA section
AUDIO IN/
OUT jacks
Connects to a tape
deck, MD deck or
DAT player, etc
FMANTENNA Connects to the FM
L
jack
wire antenna (aerial)
supplied with this
R
MULTI
CHANNEL
INPUT jacks
Connects to a Super
Audio CD player or
DVD player with an
analog audio jack for
7.1 channel or 5.1
channel sound (page
AM
ANTENNA
jack
Connects to the AM
loop antenna (aerial)
supplied with this
XM
ANTENNA
jack
Connects to the XM
connect-and-Play
antenna (aerial) (not
PRE OUT jacks Connects to an
external power
amplifier.
D COMPONENT VIDEO INPUT/
OUTPUT section
B DIGITAL INPUT/OUTPUT section
COMPONENT Connects to a DVD
VIDEO (Y, P / player, TV, or a
B
OPTICAL IN/ Connects to a DVD
C , P /C )
INPUT/
satellite tuner. (page
B
R
R
OUT jacks
player, Super Audio
CD player, etc. The
COAXIAL jack
provides a better
quality sound (page
OUTPUT
jacks*
COAXIAL IN
jacks
HDMI IN/OUT Connects to a DVD
jacks
player, or a satellite
tuner. An image and
the sound are output
to TV or a projector
continued
11GB
Download from Www.Somanuals.com. All Manuals Search And Download.
E VIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jacks
Connects to a VCR
L
or a DVD player etc.
R
VIDEO IN/
OUT jacks*
S VIDEO IN/
OUT jacks*
F SPEAKERS section
Connects to speakers
* You can watch the selected input image when you
connect the MONITOR OUT jack to a TV (page
the sound field on the monitor when you press ON
12GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Remote commander
A AV ?/1
Press to turn on or off the audio/
You can use the supplied remote RM-AAL003
to operate the receiver and to control the Sony
audio/video components that the remote is
(on/standby) video components that the
remote is assigned to operate
(page 104).
If you press the ?/1 (B) at the
same time, it will turn off the
receiver and other Sony
components (SYSTEM
STANDBY).
RM-AAL003
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
button (C).
B ?/1
Press to turn the receiver on or
(on/standby) off.
After pressing ZONE 2 (D),
only the receiver in zone 2 is
turned on or off with this button.
To turn off all components,
press ?/1 and AV ?/1 (A) at
the same time (SYSTEM
STANDBY).
C Input
buttons
Press one of the buttons to
select the component you want
to use. To utilize the buttons
with names in pink, press
SHIFT (wg), and then press the
button. When you press any of
the input buttons, the receiver
turns on. The buttons are
factory assigned to control Sony
program the remote to control
non-Sony components
following the steps in
(page 104).
D ZONE 2
Press to enable zone 2 operation
E SLEEP
Press to activate the Sleep
Timer function and the duration
which the receiver turns off
F RECEIVER Press to enable the receiver
G 2CH
A.F.D.
Press to select a sound field
MOVIE
MUSIC
continued
13GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
Function
Name
Function
H Numeric
Press to
P PRESET
Press to register FM/AM/XM
Radio stations or to select preset
stations.
b)
buttons
– preset/tune to preset stations.
– select track numbers of the
CD player, DVD player or
MD deck. Press 0/10 to
select track number 10.
– select channel numbers of
the VCR or satellite tuner.
– After pressing TV (wj),
press the numeric buttons to
select the TV channels.
+
/–
TV CH +/–
Press TV (wj) and then press
TV CH+/– to operate the TV,
satellite tuner, VCR, etc.
Q F1/F2
Press TV (wj) and then press
F1 or F2 to select a component
to operate.
• Hard disk recorder
F1: HDD
F2: DVD
• DVD/VHS combo player
F1: DVD
I ENTER
Press to enter the value after
selecting a channel, disc or
track using the numeric buttons.
MEMORY
Press to store a tuner station
during tuner operation.
F2: VHS
TV/VIDEO
WIDE
Press TV/VIDEO and TV (wj)
at the same time to select the
input signal (TV input or video
input).
J DISPLAY
Press to select information
displayed on the display
window, TV screen of the VCR,
satellite tuner, CD player, DVD
Press to select the wide picture
mode.
K
After pressing MENU (qd) or
TOP MENU (qk), press V/v, B
or b to select the settings. Then
MACRO1,
MACRO2
Press RECEIVER (6) and
then press MACRO 1 or
MACRO 2 to set up the macro
function (page 107).
V/v/B/b
press
to enter the selection
R TOP MENU Press to display the menu or
on-screen guide of the DVD
L TOOLS
Press to display and select items
from the option menus for DVD
player, etc.
OPTIONS
player on the TV screen. Then
use V/v/B/b and
menu operations.
to perform
M MENU
Press to display the menu of the
receiver, DVD player, or TV,
etc.
MENU
Press to display the menus of
the DVD player on the TV
screen. Then use V/v/B/b and
to perform a menu
N CATEGORY Press to select the category for
·
REPLAY B / Press to replay the previous
ADVANCE
scene or fast forward the current
scene of the VCR or DVD
player.
NIGHT
MODE
Press RECEIVER (6) and
then press NIGHT MODE to
activate the NIGHT MODE
·
b
a)
O m/M
Press to operate the DVD
player, CD player, MD deck or
tape deck, etc.
a)
x
INPUT
MODE
Press RECEIVER (6) and
then press INPUT MODE to
select the input mode when the
same components are
a)
X
H
b)
a)
./>
connected to both digital and
CATEGORY Press to select the category
S MUTING
Press to activate the muting
85).
14GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Name
Function
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
T MASTER
Press to adjust the volume level
of all speakers at the same time
VOL +/–
TV VOL +/– Press TV (wj) and then press
TV VOL +/– to adjust the
volume level of the TV.
U DISC SKIP Press to skip a disc when using
a multi-disc changer.
V RETURN/
Press to return to the previous
menu or exit the menu while the
menu or on-screen guide of the
VCR, DVD player, or satellite
tuner is displayed on the TV
EXIT O
W ON SCREEN Press to display the receiver
status. Then, if you press
MENU (qd), the menus of the
X CLEAR
Press to
– clear a mistake when you
press the incorrect numeric
button.
– return to continuous
playback, etc. of the satellite
tuner or DVD player.
>10
Press to select
– track numbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
– channel numbers of the
Digital CATV terminal.
D.TUNING
Press to enter direct tuning
Y SHIFT
Z A.DIRECT
wj TV
Press to light up the button. It
changes the remote button
function to activate the buttons
with pink printing.
Press to switch the audio of the
selected input to analog signal
without any adjustment (page
77).
Press to enable TV operation.
wk RM SET UP Press to set up the remote.
a)
buttons that you can use to control each
component.
The tactile dot is attached to these buttons (H,
b)
PRESET+). Use as a mark of operation.
15GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Installing speakers
This receiver allows you to use a 7.1 channel
system (7 speakers and one sub woofer).
You can enjoy high fidelity reproduction of
DVD software recorded sound in the Surround
EX format if you connect one additional
surround back speaker (6.1 channel system) or
two surround back speakers (7.1 channel
system). (see “Using the surround back
62).
Enjoying a 5.1/7.1 channel
system
To fully enjoy theater-like multi-channel
surround sound requires five speakers (two
front speakers, a center speaker, and two
surround speakers) and a sub woofer (5.1
channel system).
Example of a 7.1 channel
speaker system configuration
Example of a 5.1 channel
speaker system configuration
AFront left speaker
BFront right speaker
CCenter speaker
DSurround left speaker
ESurround right speaker
FSurround back left speaker
GSurround back right speaker
HSub woofer
AFront left speaker
BFront right speaker
CCenter speaker
DSurround left speaker
ESurround right speaker
HSub woofer
Tips
• When you connect a 6.1 channel speaker system,
place the surround back speaker behind the
listening position.
• Since the sub woofer does not emit highly
directional signals, you can place it wherever you
want.
16GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Connecting speakers
H
G
F
FRONT SPEAKERS
B terminals a)
A
B
E
D
C
B
A
AMonaural audio cord (not supplied)
BSpeaker cords (not supplied)
a)
b)
AFront speaker A (L)
BFront speaker A (R)
CCenter speaker
DSurround speaker (L)
ESurround speaker (R)
If you have an additional front speaker
system, connect them to the FRONT
SPEAKERS B terminals. You can select
the front speaker system you want to use
with the SPEAKERS (OFF/A/B/A+B) on
If you connect only one surround back
speaker, connect it to the SURROUND
BACK SPEAKERS L terminal.
b)
FSurround back speaker (L)
b)
GSurround back speaker (R)
c)
HSub woofer
continued
17GB
Download from Www.Somanuals.com. All Manuals Search And Download.
c)
When you connect a sub woofer with an auto
standby function, turn off the function when
watching movies. If the auto standby
function is set to on, it turns to standby mode
automatically based on the level of the input
signal to a sub woofer, then sound may not
be output.
Note
When you connect all the speakers with a nominal
impedance of 8 ohms or higher, set “SP.
IMPEDANCE” in the System Settings menu to “8
ohm.” In other connections, set it to “4 ohm.” For
Tip
To connect certain speakers to another power
amplifier, use the PRE OUT jacks. The same signal
is output from both the SPEAKERS terminals and
the PRE OUT jacks. For example, if you want to
connect just the front speakers to another amplifier,
connect that amplifier to the PRE OUT FRONT L
and R jacks.
ZONE 2 connection
You can assign the SURROUND BACK
SPEAKER terminals F and G to the
speakers of the ZONE 2. Set the surround back
on connection and operation in zone 2.
18GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3a: Connecting the audio components
How to hook up your
components
Audio input/output jacks to be
connected
This section describes how to hook up your
components to this receiver. Before you begin,
for the pages which describe how to connect
each component.
The sound quality depends on the jack used.
Refer to the illustration that follows. Select the
connection configuration according to the
jacks of your components.
After hooking up all your components,
proceed to “4: Connecting the antennas
Component to be connected
Page
Super Audio CD
player/ CD player
With digital audio
output
Digital
Analog
With multi-channel
audio output
High quality sound
With analog audio
output only
MD/DAT
With digital audio
output
Notes
With analog audio
output only
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
Tape deck, Analog disc turntable
Tip
All the digital audio jacks are compatible with 32
kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
19GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
digital audio input/output jacks
The following illustration shows how to
connect a Super Audio CD player, CD player
and an MD/DAT deck.
Super Audio CD
player, CD player
MD deck,
DAT deck
C
A
B
A
AAudio cord (not supplied)
BCoaxial digital cord (not supplied)
COptical digital cord (not supplied)
20GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on playing a Super Audio
CD on a Super Audio CD player
• No sound is output when playing a Super
Audio CD on a Super Audio CD player
connected to only the COAXIAL SA-CD/
CD IN jacks on this receiver. When you play
a Super Audio CD, connect the player to the
MULTI CHANNEL INPUT or SA-CD/CD
IN jacks. Refer to the operating instructions
supplied with the Super Audio CD player.
• You cannot make digital recordings of a
Super Audio CD. Use the analog jack for
recording in this case.
• When connecting optical digital cords, insert
the plugs straight in until they click into
place.
• Do not bend or tie digital optical cords.
If you want to connect several
digital components, but cannot
find an unused input
Tip
You cannot connect an LD player’s DOLBY
DIGITAL RF OUT jack directly to this receiver’s
digital input jacks. You must use an RF demodulator
for this configuration.
21GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
multi-channel output jacks
If your DVD or Super Audio CD player is
equipped with multi-channel output jacks, you
can connect it to the MULTI CHANNEL
INPUT jacks of this receiver to enjoy multi-
channel sound. Alternatively, the multi-
channel input jacks can be used to connect an
external multi-channel decoder.
DVD player, Super Audio
CD player, etc.
A
B
AAudio cord (not supplied)
BMonaural audio cord (not supplied)
Notes
• DVD and Super Audio CD players do not have the
SURROUND BACK jacks.
• When “SUR BACK SP” is set to “ZONE 2” in the
Speaker Settings menu, the input to the SUR
22GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
analog audio jacks
The following illustration shows how to
connect a component with analog jacks, such
as tape deck, turntable, etc.
Super Audio
CD player,
CD player
Tape deck
A
A
A
A
MD deck,
DAT deck
Turntable
AAudio cord (not supplied)
Note
If your turntable has a ground (earth) wire, connect
it to the (U) SIGNAL GND terminal.
23GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3b: Connecting the video components
How to hook up your
components
Video input/output jacks to be
connected
This section describes how to hook up your
components to this receiver. Before you begin,
for the pages which describe how to connect
each component.
The image quality depends on the connecting
jack. Refer to the illustration that follows.
Select the connection according to the jacks on
your components.
After hooking up all your components,
proceed to “4: Connecting the antennas
Component to be connected
TV monitor
Page
Digital
Analog
DVD player, DVD recorder
Satellite tuner
With HDMI jack
High quality image
VCR
Camcorder, video game, etc.
24GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
HDMI jacks
HDMI is the abbreviated name for High-
Definition Multimedia Interface. It is an
interface which transmits video and audio
signals in digital format.
HDMI features
• A digital audio signals transmitted by HDMI
can be output from the speakers and the PRE
OUT jacks on this receiver. This signal
supports Dolby Digital, DTS, and linear
PCM.
• Analog video signals input to the VIDEO
jack, S VIDEO jacks, or COMPONENT
VIDEO jacks can be output as HDMI
signals. Audio signals are not output from an
HDMI OUT jack when the image is
converted.
DVD player
Satellite tuner
TV monitor, projector, etc.
Audio/video
signals
Audio/video
signals
Audio/video
signals
A
A
A
AHDMI cable (not supplied)
We recommend that you use a Sony HDMI cable.
continued
25GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Set the resolution of the image of the
playback component to 720p or 1080i when
you output 96 kHz multi-channel sound over
an HDMI connection.
• Refer to the operating instructions of each
component connected for details.
• We do not recommend using an HDMI-DVI
conversion cable. When you connect an
HDMI-DVI conversion cable to a DVI-D
component, the sound and/or the image may
not be output. Connect other audio cords or
digital connecting cords, then set “HDMI
VIDEO ASSIGN?” in the Video Settings
correctly.
Notes on HDMI connections
• Use an HDMI cable with the HDMI logo
(made by Sony).
• Check the setup of the connected component
if an image is poor or the sound does not
come out of a component connected via the
HDMI cable.
• An audio signal input to the HDMI IN jack
is output from the speaker output terminals,
HDMI OUT jack and PRE OUT jacks. It is
not output from any other audio jacks.
• Video signals input to the HDMI IN jack can
only be output from the HDMI OUT jack.
The video input signals cannot be output
from the VIDEO OUT jacks, S VIDEO
OUT jacks, or MONITOR OUT jacks.
• When you want to listen to the sound from
the TV speaker, set “HDMI AUDIO” to
“TV+AMP” in the Video Settings menu
output from the TV speaker or you cannot
playback multi-channel software.
• The multi/stereo area audio signals of a
Super Audio CD are not output.
• Be sure to turn on the receiver when video
and audio signals of a playback component
are being output to a TV through this
receiver. Unless the power is on, neither
video nor audio signals will be transmitted.
• Audio signals (sampling frequency, bit
length, etc.) transmitted from an HDMI jack
may be suppressed by the connected
component. Check the setup of the
connected component if an image is poor or
the sound does not come out of a component
connected via the HDMI cable.
• Sound may be interrupted when the
sampling frequency or the number of
channels of audio output signals from the
playback component is switched.
• When the connected component is not
compatible with copyright protection
technology (HDCP), the image and/or the
sound from the HDMI OUT jack may be
distorted or may be not output.
In this case, check the specification of the
connected component.
26GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a TV monitor
The image from a visual component connected
to this receiver and the menu of this receiver
can be displayed on a TV screen.
It is not necessary to connect all the cables.
Connect audio and video cords according to
the jacks of your components.
TV monitor
Video signals
Audio signals
A
B
C
D
E
AAudio cord (not supplied)
BOptical digital cord (not supplied)
CComponent video cord (not supplied)
DS video cord (not supplied)
EVideo cord (not supplied)
continued
27GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Connect image display components such as a TV
monitor or a projector to the MONITOR OUT jack
on the receiver. You may not be able to record, even
if you connect recording components.
• Turn on the receiver when the video and audio of a
playback component are being output to a TV via
the receiver. If the power supply of the receiver is
not turned on, neither video nor audio is
transmitted.
• Depending on the status of the connection between
the TV and the antenna (aerial), the image on the
TV screen may be distorted. In this case, place the
antenna (aerial) farther away from the receiver.
Tips
• The receiver has a video conversion function. For
• You can watch the selected input image when you
connect the MONITOR OUT jack to a TV monitor.
You can also display certain menu settings and the
sound field on the monitor when you press ON
• The sound of the TV is output from the speakers
connected to the receiver if you connect the sound
output jack of the TV and the TV/SAT AUDIO IN
jacks of the receiver. In this configuration, set the
sound output jack of the TV to “Fixed” if it can be
switched between either “Fixed” or “Variable.”
28GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player/DVD
recorder
The following illustration shows how to
connect a DVD player/DVD recorder.
It is not necessary to connect all the cables.
Connect audio and video cords according to
the jacks of your components.
Note
To output multi-channel digital audio, set the digital
audio output setting on the DVD player. Refer to the
operating instructions supplied with the DVD
player.
Connecting a DVD player
DVD player
Video signals
Audio signals
A
B
C
D
E
ACoaxial digital cord (not supplied)
BAudio cord (not supplied)
CComponent video cord (not supplied)
DS video cord (not supplied)
EVideo cord (not supplied)
continued
29GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a satellite tuner
The following illustration shows how to
connect a satellite tuner.
It is not necessary to connect all the cables.
Connect audio and video cords according to
the jacks of your components.
Satellite tuner
Video signals
Audio signals
A
B
C
D
E
AOptical digital cord (not supplied)
BAudio cord (not supplied)
CComponent video cord (not supplied)
DS video cord (not supplied)
EVideo cord (not supplied)
31GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting components with
analog video and audio jack
The following illustration shows how to
connect a component which has analog jacks
such as a VCR, etc.
It is not necessary to connect all the cables.
Connect audio and video cords according to
the jacks of your components.
VCR
Audio signals
Video signals
A
B
To the VIDEO 3 IN/PORTABLE
AV IN jacks (Front panel)
C
Camcorder,
video game
D
AAudio cord (not supplied)
BVideo cord (not supplied)
CS video cord (not supplied)
DAudio/video cord (not supplied)
32GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Function for conversion of video
signals
This receiver is equipped with a function for
converting video signals. You can output the
video signal after connecting this receiver via
the MONITOR OUT jack as shown in the
illustration.
• Video signals can be output as HDMI video,
component video and S video signals.
• S video signals can be output as HDMI
video, component video and video signals.
• Component video signals can be output as
HDMI video, S video and video signals.
In the video input/output conversion table of the receiver
Input Signals
Output Signals
B C D
B C D
A B C D
OUTPUT jack
COMPONENT VIDEO
MONITOR OUT
S VIDEO
MONITOR OUT
VIDEO
MONITOR OUT
HDMI OUT
INPUT jack
HDMI IN 1/2 A
f
X
X
X
COMPONENT
a
a
VIDEO IN B
a
f
(Supports inputsignals (Supports inputsignals
less than 480i.)
less than 480i.)
S VIDEO IN C
a
a
a
a
a/f*
a
VIDEO IN D
a
a/f*
a : Video signals are converted and output through the video converter.
f : The same type of signal as that of the input signal is output. Video signals are not converted.
X : Video signals are not output.
* Video signals are output when “VIDEO CONVERT” is set to “OFF” in the Video Settings menu.
continued
33GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on converting video signals
• You can convert only 480i component video
signals into HDMI signals, S video signals,
or video signals. Signals are converted from
480i interlace scanning to 480p progressive
scanning, then the signals are output.
• When video or S video signals from a VCR,
etc., are converted on this receiver and then
output to your TV, depending on the status of
the video signal output, the image on the TV
screen may appear distorted horizontally or
no image may be output.
• HDMI video signals cannot be converted to
component video signals, S video signals,
and video signals.
• The converted video signals are output only
from the MONITOR OUT jacks. They are
not output from VIDEO OUT jacks,
S VIDEO OUT jacks, or the ZONE 2
VIDEO OUT jack.
Closed Caption display
When the receiver receives video output
signals that are up-converted but the
accompanying closed caption cannot be
displayed, down-convert the video output
signals to the original video signals, and
connect the TV to the MONITOR OUT jack
that outputs the original video signals.
To connect a recording
component
When recording, connect the recording
component to the VIDEO OUT jacks or S
VIDEO OUT jacks of the receiver. Connect
cords for input and output signals to the same
type of jack, as VIDEO OUT jacks and S
VIDEO OUT jacks do not have an up-
conversion function.
• S2 information (aspect information for the
images) included in S video signals is
effective only when S video input signals are
output from the S video MONITOR OUT
jack. An aspect ratio of images may not be
displayed correctly when video signals and
component video signals are converted and
are output from the S video MONITOR
OUT jack.
• When you play a VCR with an image
improvement circuit, such as TBC, the
images may be distorted or may not be
output. In this case, set the image
Note
Signals output from the MONITOR OUT jacks may
not be recorded properly.
improvement circuit function to off.
34GB
Download from Www.Somanuals.com. All Manuals Search And Download.
In the video input/output
conversion table classified by
the menu settings
You can set the video signal conversion
function on/off.
The relationships between the video input and
output signals set by “VIDEO CONVERT”
and “PROGRESSIVE OUT” in the Video
Settings menu are shown in the chart below.
MONITOR
OUT jacks
Menu setting
HDMI COMPONENT S VIDEO
VIDEO
OUT
VIDEO
MONITOR
OUT
MONITOR MONITOR
OUT
OUT
Input signal
VIDEO CONVERT: ON /
PROGRESSIVE OUT: OFF
Video/S video
a
a
a (480i)
a
a
a
a
Component video
(480i)
f
Component video
(Other than 480i)
a
f
X
X
VIDEO CONVERT: ON /
PROGRESSIVE OUT: ON
Video/S video
a
a
a (480p)
a
a
a
a
Component video
(480i)
a (480p)
Component video
(Other than 480i)
a
X
X
X
VIDEO CONVERT: OFF / Video
X
X
X
X
X
f
X
f
X
f
X
X
PROGRESSIVE OUT:
Dimmed in the display
S video
Component video
(480i)
Component video
(Other than 480i)
X
f
X
X
a : Video signals are converted and output through the video converter.
f : The same type of signals as those of the input signals will be output. Video signals are not converted.
X : Video signals are not output.
35GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Connecting the antennas (aerials)
Connect the supplied AM loop antenna
(aerial) and FM wire antenna (aerial).
FM wire antenna (aerial) (supplied)
AM loop antenna (aerial) (supplied)
* The shape of the connector varies depending on
the area.
Notes
• To prevent noise pickup, keep the AM loop antenna
(aerial) away from the receiver and other
components.
• Be sure to fully extend the FM wire antenna
(aerial).
• After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
• Do not use the U SIGNAL GND terminal for
grounding the receiver.
36GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Make sure that the total power consumption of the
component(s) connected to the receiver’s AC
OUTLET(s) does not exceed the wattage stated on
the rear panel. Do not connect high-wattage
electrical home appliances such as electric irons,
fans, or TVs to this outlet. This may cause a
malfunction.
5: Preparing the receiver
and the remote
Connecting the AC power cord
(mains lead)
Performing initial setup
operations
Connect the supplied AC power cord (mains
lead) to the AC IN terminal on the receiver,
then connect the AC power cord (mains lead)
to a wall outlet.
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
AC OUTLET*
AC IN terminal
1,2 2,3
2,3
1 Press POWER to turn off the
To the wall outlet
receiver.
* The configuration, shape, number of AC outlets,
and the information described on the label will
vary according to the area.
2 Press POWER while pressing
TONE MODE and MULTI CH IN.
3
Release TONE MODE and MULTI
CH IN after a few seconds.
After “MEMORY CLEARING...”
appears on the display for a while,
“MEMORY CLEARED!” appears.
The following items are reset to their
factory settings.
AC power cord
(mains lead)
(supplied)
**
• All settings in the Level Settings, EQ
Settings, Sur Settings, Tuner Settings,
Audio Settings, Video Settings, Speaker
Settings, System Settings, and Auto
Calibration menus.
• The sound field memorized for each
input and preset station.
• All preset stations.
** A several space is left between the plug and the
rear panel even when the power cord (mains
lead) is inserted firmly. The cord is supposed be
connected this way. This is not malfunction.
Notes
• The AC OUTLET(s) on the rear of the receiver is a
switched outlet, which supplies power to the
connected component only while the receiver is
turned on.
• All index names for inputs and preset.
37GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting batteries into the
remote
About the command mode
The receiver and the remote use the same
command mode.
If the command modes of the receiver and the
remote are different, you cannot use the
remote to operate the receiver.
Insert two R6 (size-AA) batteries in the RM-
AAL003 remote commander.
Observe the correct polarity when installing
batteries.
If the command modes of both the receiver and
the remote are those of the initial setting (AV
SYSTEM 2), it is not necessary to reset them.
You can switch the command mode (AV
SYSTEM 1 or AV SYSTEM 2) of the receiver
and the remote. If both the receiver and the
other Sony component respond to the same
remote command, switch the command mode
of either the component or the receiver to
another command mode so that the component
does not respond to the same remote command
as the receiver.
RM-AAL003
Notes
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
To switch the command mode
of the receiver
2CH
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the programmed
remote codes may be cleared. If this happens,
program the remote codes again (page 104).
Tip
When the remote no longer operates the receiver,
replace all the batteries with new ones.
Turn on the receiver while pressing
2CH.
When the command mode is set to “AV2,”
“COMMAND MODE [AV2]” appears on the
display.
When the command mode is set to “AV1,”
“COMMAND MODE [AV1]” appears on the
display.
38GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To switch the command mode
of the RM-AAL003 remote
6: Setting the speakers
1
Setting the speaker impedance
Set the appropriate speaker impedance for the
speakers you are using.
1
2
2
3
1 Press ?/1 while pressing RM
SET UP.
The RM SET UP button flashes.
2 Press 1 or 2 while the RM SET
4-6
UP button is flashing.
When you press 1, the command mode is
set to AV SYSTEM 1. When you press 2,
the command mode is set to AV SYSTEM
2.
3,7
1 Turn on the receiver.
3 Press ENTER when the RM SET
UP button lights up.
2 Press RECEIVER.
The RM SET UP button flashes twice,
then the command mode setting process
is completed.
Receiver operation is enabled.
3 Press MENU.
Tip
The list of setting menus appears.
When you press RM SET UP, use a thin wire, such
as a paper clip.
4 Press V/v repeatedly to select
“System Settings,” then press
to enter.
5 Press V/v repeatedly to select
“SP. IMPEDANCE,” then press
to enter the parameter.
continued
39GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press V/v repeatedly to select
“4 ohm” or “8 ohm” depending
on the speakers you are using,
Press SPEAKERS (OFF/A/B/A+B)
repeatedly to select the front
speaker system you want to drive.
then press
selection.
to enter the
Note
You cannot switch the front speakers by pressing
SPEAKER (OFF/A/B/A+B) when the headphones
are connected to the receiver.
7 Press MENU to exit the menu.
Notes
• If you are not sure of the impedances of the
speakers, refer to the operating instructions
supplied with your speakers. (This information is
often on the back of the speaker.)
• When you connect all speakers with a nominal
impedance of 8 ohms or higher, set “SP.
IMPEDANCE” to “8 ohm.” When connecting
other types of speakers, set it to “4 ohm.”
• When you connect front speakers to both the
SPEAKER A and B terminals, connect the
speakers with a nominal impedance of 8 ohms or
higher.
Set to
To select
A
The speakers connected to the
FRONT SPEAKERS A terminals.
B
The speakers connected to the
FRONT SPEAKERS B terminals.
A+B
The speakers connected to both the
FRONT SPEAKERS A and B
terminals (parallel connection).
OFF
No audio signals are output from
any speaker terminals, or the PRE
OUT terminal.
– When you connect speakers with impedance of
16 ohms or higher in both “A” and “B”
configuration:
Set “SP. IMPEDANCE” to “8 ohm” in the
System Settings menu.
– For other types of speakers in other
configurations:
Set “SP. IMPEDANCE” to “4 ohm” in the
System Settings menu.
Selecting the front speaker
You can select the front speakers you want to
drive.
SPEAKERS (OFF/A/B/A+B)
40GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• The auto calibration function does not work in the
following cases.
– MULTI IN is selected.
– The ANALOG DIRECT function is being used.
– Headphones are connected.
• Cancel if MUTING is set to on.
7: Calibrating the
appropriate settings
automatically (AUTO
CALIBRATION)
Optimizer microphone
The DCAC (Digital Cinema Auto Calibration)
function allows you to perform automatic
calibration, such as checking the connection
between each speaker and the receiver,
adjusting the speaker level, and measuring the
distance of each speaker from your listening
position automatically. Refer also to the
“Quick Setup Guide” supplied with the
receiver.
Before you perform the auto
calibration
Before you perform the auto calibration, set up
• The AUTO CAL MIC jack is used for the
supplied optimizer microphone only. Do not
connect other microphones to this jack.
Doing so may damage the receiver and the
microphone.
1 Connect the supplied optimizer
microphone to the AUTO CAL
MIC jack on the front panel.
• During the calibration, the sound that comes
out of the speakers is very loud. Pay
attention to the presence of children or to the
effect on your neighborhood.
• Perform the auto calibration in a quiet
environment to avoid the effect of noise and
get a more accurate measurement.
2 Set up the optimizer
microphone.
Place the optimizer microphone at your
listening position. Use a stool or tripod so
that the optimizer microphone remains at
the same height as your ears.
• If there are any obstacles in the path between
the optimizer microphone and the speakers,
the calibration cannot be performed
correctly. Remove any obstacles from the
measurement area to avoid measurement
error.
On setting up the active sub
woofer
• When a sub woofer is connected, turn on the
sub woofer and turn up the volume
beforehand.
• If you connect a sub woofer with a crossover
frequency function, set the value to the
maximum.
• If you connect a sub woofer with an auto
standby function, set this function to off
(deactivated).
• When you use a bi-amplifier connection, set
“SUR BAK SP” to “BI-AMP” in the
Speaker Settings menu before you perform
continued
41GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Depending on the characteristics of the sub woofer
you are using, the setup distance value may be
further away from the actual position.
1
3
Using the receiver as a pre-
amplifier
You can use the auto calibration function when
you use the receiver as a pre-amplifier.
In this case, the distance value shown on the
display may differ from the actual distance
value. However, there will be no problems
even if you continue to use the receiver with
that value.
2
5-8
4
Performing the auto calibration
1 Turn on the receiver and the TV.
The auto calibration function allows you to
measure the following:
2 Press ON SCREEN.
a)
• Whether or not speakers are connected
Switch the input of the TV so that the
setting menu is displayed on the TV
screen connected to this receiver.
• Terminal types of speakers connected
• Distance of each speaker from your listening
b)
position
b)
3 Press RECEIVER.
• Speaker size
• Speaker level
• Frequency characteristics
Receiver operation is enabled.
c)
4 Press MENU.
a)
This receiver corrects signals by analog downmix
The list of setting menus appears.
processing only for the center speaker and sub
woofer when MULTI IN is selected. The
correction is invalid for other speakers.
The measurement result is not utilized when
MULTI IN is selected.
5 Press V/v repeatedly to select
“Auto Calibration,” then press
to enter the menu.
b)
c)
• DTS 96/24 signals are always played back as 48
kHz when you correct signals.
• The measurement result is not utilized in the
following cases.
– MULTI IN is selected.
– Input signals of which the sampling frequency
is more than 96 kHz are being received.
42GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press V/v repeatedly to select
9 Measurement starts.
“CAL TYPE,” then press
enter the parameter.
to
The measurement process will take
approximately 30 seconds. Wait until the
measurement process completes.
7 Press V/v repeatedly to select
Note
the parameter, then press
enter the selection.
to
You cannot measure the speaker height of the
surround speakers and the surround back speakers.
Set this value from “SP POSI.” settings in the
Calibration
type
Explanation
ENGINEER
Sets the frequency
Tips
characteristics to a set that
matches that of the Sony
listening room standard.
• Operations other than turning the receiver on or off
and pressing ON SCREEN to turn the display on or
off are deactivated during auto calibration.
• In the following situations, the measurements may
not be performed correctly or auto calibration
cannot be performed.
– when special speakers, such as dipole speakers
are used.
– when the multi zone function is used in zone 2.
FULL FLAT
FRONT REF
Makes the measurement of
frequency from each
speaker flat.
Adjusts the characteristics
of all the speakers to match
the characteristics of the
front speaker.
To cancel auto calibration
Auto calibration is cancelled when you change
the volume, switch functions, change the
speaker setting of the receiver, or connect
headphones.
8 Press V/v repeatedly to select
“AUTO CAL START,” then press
to start the measurement.
Measurement starts in five seconds. A
countdown appears on the TV screen.
While the time is counting down, stand
away from the measurement area to
avoid measurement error.
43GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Explanation
Confirming/saving the
measurement results
DIST.INFO
Displays the measurement
result for speaker distance.
LEVEL INFO Displays the measurement
result for speaker level.
1 Confirm the measurement
result.
EXIT
Exits the setting process
without saving the
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
measurement results.
3 Press V/v repeatedly to select a
Measurement Display
result
Explanation
preset number to be used, then
press
.
When the
measurement
process
COMPLETE Proceed to step
2.
4 Press
.
completes
properly
The measurement results are saved.
Tip
When the
ERROR
See “When
The size of a speaker (LARGE/SMALL) is
determined by the low characteristics. The
measurement
process fails
appear” (page
44).
measurement results may vary, depending on the
position of the optimizer microphone and speakers,
and the shape of the room. It is recommended that
you follow the measurement results. However, you
can change those settings in the Speaker Settings
then try to change the settings if you want.
2 Press V/v repeatedly to select
the item, then press
.
When error codes appear
Try the remedies and re-perform the auto
calibration.
Error code
Cause and remedies
CODE 31
SPEAKERS (OFF/A/B/A+B) is
set to OFF. Set it to others and re-
perform the auto calibration.
Item
Explanation
CODE 32
None of the speakers were
detected. Make sure that the
optimizer microphone is
connected properly and re-
perform the auto calibration.
If the optimizer microphone is
connected properly but the error
code appears, the optimizer
microphone cable may be
damaged or improperly
RETRY
Re-performs the auto
calibration.
SAVE EXIT
Saves the measurement
results and exits the setting
process.
WRN CHECK Displays a warning
concerning the
measurement results. See
connected.
CODE 33 (F)
None of the front speakers are
connected or only one front
speaker is connected.
The optimizer microphone is not
connected.
PHASE INFO Displays the phase of each
speaker (in phase/out of
phase). See “When you
44GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Error code
Cause and remedies
Warning code Explanation
CODE 33 (SR) • Either the left or right surround
speakers is not connected.
• Surround back speakers are
connected even though
WARNING 41 The sound input from the
optimizer microphone is outside
the acceptable range. It is louder
than the loudest sound that can be
measured. Try to perform the auto
calibration when the environment
is quiet enough to allow proper
measurement.
surround speakers are not
connected. Connect the
surround speaker to the
SURROUND terminal.
CODE 33 (SB) The surround back speaker is
connected only to the
WARNING 42 The volume of the receiver is out
of the acceptable range. Try to
SURROUND BACK
perform the auto calibration when
the environment is quiet enough
to allow proper measurement.
SPEAKERS R terminal. When
you connect only one surround
back speaker, connect it to the
SURROUND BACK
WARNING 43 The distance and position of a sub
woofer cannot be detected. Or the
angle of the speaker position
cannot be detected. This may be
caused by noise. Try to perform
the auto calibration in a quiet
environment.
SPEAKERS L terminal.
•CODE 31
1 Press
, then follow the instructions from step
NO WARNING There is no warning information.
•CODE 32, 33
1 When you press
, “RETRY?” appears.
When you select “PHASE INFO”
You can check the phase of each speaker (in
phase/out of phase).
2 Press V/v to select “YES,” then press
3 Follow the instructions from step 2 of
4 Press V/v repeatedly to select preset number to
store preset settings then press
.
Press V/v repeatedly to select a
.
speaker, then press
to return to
step 1 in “Confirming/saving the
When you select “WRN CHECK”
If a warning on the measurement result is
present, detailed information is displayed.
Press
to return to step 1 of
Warning code Explanation
WARNING 40 The auto calibration has
completed. However, the noise
level is high. You may be able to
perform the auto calibration
properly if you try it again, even
though the measurement cannot
be performed in all environments.
Try to perform the auto
calibration in a quiet
environment.
continued
45GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• ERROR CODE xxx:3x
Appears when the measurement fails. For
details on each message, see “Confirming/
• RETRY?
Appears to ask you to re-measure or exit
without re-measuring when the
measurement fails.
Display
Explanation
IN-PHASE
The speaker is in phase.
OUT-OF-
PHASE
The speaker is out of phase. The
“+” and “–” terminals of the
speaker may be connected the
other way around. However,
depending on the speakers,
“OUT-OF-PHASE” appears on
the display even though the
• CANCEL
speakers are connected properly.
This is because of the speakers’
specifications. In this case, you
can continue to use the receiver.
Appears when you cancel auto calibration
during the measurement.
x CAL TYPE*
----------
No speakers are connected.
(Parameter type)
• ENGINEER
Tip
Sets the frequency to one that matches that
of the Sony listening room standard.
• FULL FLAT
Makes the measurement of frequency from
each speaker flat.
Depending on the position of the sub woofer, the
measurement results for polarity may vary.
However, there will be no problems even if you
continue to use the receiver with that value.
• FRONT REF
Auto Calibration menu
parameters
Adjusts the characteristics of all the speakers
to match the characteristics of the front
speaker.
x AUTO CAL START?
(Starts auto calibration)
• MEASUREMENT COUNTDOWN
A time countdown appears on the display
from five seconds to one second.
• MEASURING TONE
x EQ CURVE EFFECT*
(Activates/deactivates the EQ
curve measurement)
• OFF
Deactivates the EQ curve measurement.
• ON
Activates the EQ curve measurement.
After the measurement is completed, this
setting is set to ON automatically.
Appears while TONE is being measured.
• MEASURING T.S.P.
Appears while TSP is being measured.
• MEASURING WOOFER
Appears while WOOFER is being
measured.
• COMPLETE
*
DTS 96/24 signals are played back as 48 kHz
signals if the frequency response measurement
result is utilized.
The frequency response measurement result is not
utilized in the following cases.
– When the MULTI IN is selected.
– Input signals of which the sampling frequency is
more than 96 kHz are being received.
Appears when the measurement process
completes successfully. For details on each
message, see “Confirming/saving the
• WARNING CODE xxx:4x
Appears if a warning on the measurement
result is present. For details on each
message, see “Confirming/saving the
• NO WARNING
*
There is no warning information.
46GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x A.CAL LOAD?
(Loads a preset measurement)
• PRESET-1
Loads the measurement value stored as
“PRESET-1.”
• PRESET-2
Loads the measurement value stored as
“PRESET-2.”
• PRESET-3
Loads the measurement value stored as
“PRESET-3.”
• OFF
Select this when you do not want to load a
preset value.
x A.CAL SAVE?
(Saves the measurement value)
• PRESET-1
Saves the measurement results as
“PRESET-1.”
• PRESET-2
Saves the measurement results as
“PRESET-2.”
• PRESET-3
Saves the measurement results as
“PRESET-3.”
x A.CAL NAME?
(Naming inputs)
You can change the preset to name to
something more recognizable.
47GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selected
input
Components that can be
played back
Playback
VIDEO 1, 2
VCR, etc., connected to the
VIDEO 1 or VIDEO 2 jack
Selecting a component
VIDEO 3
Video camera and TV game,
etc., connected to the VIDEO
3 jack
DVD
DVD player, etc., connected
to DVD jack
TV/SAT
Satellite tuner, etc., connected
to the TV/SAT jack
1
TAPE/CD-R Tape deck, etc., connected to
the TAPE jack
1
MD/DAT
MD or DAT deck, etc.,
connected to the MD/DAT
jack
SA-CD/CD
Super Audio CD or CD
player, etc., connected to the
SA-CD/CD jack
TUNER
PHONO
Built-in radio tuner
Turntable, etc., connected to
the PHONO jack
MULTI IN
SOURCE
HDMI 1, 2
Component connected to the
MULTI CHANNEL INPUT
jack
3
The current input selected for
zone 2 (Activated while
“ZONE 2” is lit.).
MUTING
HDMI componentsconnected
to the HDMI jack
1 Press one of the input button.
When you want to select a
2 Turn on the component and
start playback.
component connected to the
PHONO or the MULTI CHANNEL
INPUT jack, press SHIFT and
then press PHONO or MULTI IN.
You can also use INPUT SELECTOR on
the receiver. The selected input appears
on the display. To select a component
connected to the HDMI IN1/2 jack, press
the HDMI button repeatedly. To select a
component connected to the MULTI
CHANNEL INPUT jack, press MULTI
CH IN button.
3 Press MASTER VOL +/– to
adjust the volume.
You can also use MASTER VOLUME on
the receiver.
The initial volume level is set to minimum
(muting).
48GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate the muting function
Press MUTING on the remote. To cancel,
press MUTING on the remote again or turn
MASTER VOLUME clockwise to raise the
volume. Even if you turn off the receiver, the
muting function works when you turn the
receiver on again.
To avoid damaging your
speakers
Before you turn off the receiver, be sure to turn
down the volume level.
49GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to a Super Audio CD/CD
2
3
5
3
5
1 Turn on the Super Audio CD player or CD
• The operation is described for a
Sony Super Audio CD player.
• Refer to the operating
instructions supplied with the
Super Audio CD player or CD
player.
player, then place the disc in the tray.
2 Turn on the receiver.
3 Press SA-CD/CD.
You can also use INPUT SELECTOR on the receiver to
select “SA-CD/CD.”
z
You can select the sound field to
suit the music. Refer to page 74
for details.
An example of the display
Recommended sound fields:
Classical: HALL
Jazz: JAZZ CLUB
Live concert: LIVE CONCERT,
STADIUM
4 Play back the disc.
5 Adjust to a suitable volume.
6 After you have finished listening to a Super
Audio CD or CD, eject the disc and turn off
the receiver and the Super Audio CD player
or CD player.
50GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching a DVD
2
3
7
3
MULTI CHANNEL DECODING lamp
7
1 Turn on the TV and DVD player.
2 Turn on the receiver.
3 Press DVD.
• Refer to the operating
instructions supplied with the
TV and DVD player.
z
You can also use INPUT SELECTOR on this receiver to
select “DVD.”
Select the sound format of the
disc to be played, if necessary.
An example of the display
z
You can select the sound field to
suit the movie or the music. Refer
Recommended sound fields:
Movie: CINEMA STUDIO EX
Live image: LIVE CONCERT
Sport: SPORTS
4 Switch the input of the TV so that an image
of the DVD is displayed.
5 Set up the DVD player.
Check the following if you cannot
listen to the multi-channel sound.
• Be sure the sound source
corresponds to the multi-
channel format (the MULTI
CHANNEL DECODING lamp
on the front panel lights up
during playback).
Refer to “Quick Setup Guide” supplied with the receiver.
6 Play back the disc.
7 Adjust to a suitable volume.
8 After you have finished watching a DVD,
eject the disc and turn off the receiver, the
TV, and the DVD player.
• Be sure this receiver is
connected to the DVD player via
a digital connection.
• Be sure the digital audio output
of the DVD player is set up
properly.
51GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying video games
2
3
7
3
VIDEO 3 IN/PORTABLE AV IN
7
1 Turn on the TV and video game.
2 Turn on the receiver.
3 Press VIDEO 3*.
• Refer to the operating
instructions supplied with the
TV and video game.
You can also use INPUT SELECTOR on this receiver to
select “VIDEO 3*.”
* When you connect a TV game to the VIDEO 3 IN/PORTABLE
AV IN jack on the front panel.
An example of the display
4 Switch the input of the TV so that an image
of the video game is displayed.
5 Set up the video game.
6 Place the disc in the tray and play it back on
the video game.
7 Adjust to a suitable volume.
8 After you have finished playing a game, eject
the disc and turn off the receiver, the TV, and
the video game.
52GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching video
2
3
6
3
6
1 Turn on the VCR.
2 Turn on the receiver.
3 Press VIDEO 1*.
• Refer to the operating
instructions supplied with the
TV and VCR.
You can also use INPUT SELECTOR on this receiver to
select “VIDEO 1*.”
* When you connect VCR to the VIDEO 1 jack.
An example of the display
4 Switch the input of the TV so that an image
of the VCR is displayed.
5 Play back the tape on the VCR.
6 Adjust to a suitable volume.
7 After you have finished watching a video,
eject the tape and turn off the receiver, the
TV, and the VCR.
53GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To return to the previous
display
Press RETURN/EXIT O.
Amplifier Operations
Navigating through
menus
By using the amplifier menus, you can make
various adjustments to customize the receiver.
To exit the menu
Press MENU.
Note
Some parameters and settings may appear dimmed
on the display. This means that they are either
unavailable or fixed and unchangeable.
1
3-6
RETURN/
EXIT O
2
1 Press RECEIVER.
Receiver operation is enabled.
2 Press MENU.
The list of setting menus appears.
3 Press V/v repeatedly to select
the menu you want.
4 Press
to enter the menu.
5 Press V/v repeatedly to select
the parameter you want to
adjust.
6 Press
to enter the
parameter.
7 Repeat steps 3 to 6 when you
want to make other settings.
54GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the menus
The following options are available in each
menu. For details on navigating through
Menu
Item
Parameter
Initial
setting page
Refer
1-Level
Settings
TEST TONE
[xxxxxxxx]
OFF, AUTO, FIX
OFF page 58
PHASE NOISE
[xxxxxxx]
OFF, L/C, C/R, R/SL, R/SR, SR/SL, OFF
SR/SBR, SBR/SBL, SBL/SL, SL/L, L/
SR
PHASE AUDIO
[xxxxxxx]
OFF, L/C, C/R, R/SL, R/SR, SR/SL, OFF
SR/SBR, SBR/SBL, SBL/SL, SL/L, L/
SR
FRONT BAL. [xxx.x dB] R+20.0dB to L+20.0dB (0.5dB step) 0dB
CENTER [xxx.x dB]
–20.0dB to +10.0dB (0.5dB step)
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
OFF
1
SURROUND L [xxx.x dB] –20.0dB to +10.0dB (0.5dB step)
SURROUND R [xxx.x dB] –20.0dB to +10.0dB (0.5dB step)
SUR BACK [xxx.x dB]
–20.0dB to +10.0dB (0.5dB step)
SUR BACK L [xxx.x dB] –20.0dB to +10.0dB (0.5dB step)
SUR BACK R [xxx.x dB] –20.0dB to +10.0dB (0.5dB step)
SUB WOOFER [xxx.x dB] –20.0dB to +10.0dB (0.5dB step)
MULTI CH SW [xxx.x dB] 0dB, +10.0dB
D. RANGE COMP. [xxx]
OFF, STD, MAX
2-EQ Settings EQ PRESET [xxx]
1, 2, 3, 4, 5, OFF
page 59
FRONT BASS [xxx dB]
–10.0dB to +10.0dB (1dB step)
0dB
0dB
0dB
0dB
FRONT TREBLE [xxx dB] –10.0dB to +10.0dB (1dB step)
CENTER BASS [xxx dB]
–10.0dB to +10.0dB (1dB step)
–10.0dB to +10.0dB (1dB step)
CENTER TREBLE [xxx
dB]
SUR/SB BASS [xxx dB]
–10.0dB to +10.0dB (1dB step)
0dB
0dB
NO
SUR/SB TREBLE [xxx dB] –10.0dB to +10.0dB (1dB step)
PRESET x CLEAR [xxx] YES, NO
continued
55GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Item
Parameter
Initial
setting page
Refer
3-Sur Settings SOUND FIELD SELECT ?
A.F.D.
AUTO
page 72
SB DECODING [xxxx]
OFF, AUTO, ON
AUTO
page 61
SB DEC MODE
[xxxxxxx]
DDEX, PLIIx MV, PLIIx MS
PLIIx
MV
EFFECT LEVEL [xxx%]
20% to 120% (5% step)
8 step
100%
CENTER WIDTH [x]
3
0
DIMENSION
FRONT +3 to SUR +3
[xxxxxxx]
PANORAMA MODE [xxx] OFF, ON
OFF
ON
ON
SCREEN DEPTH [xxx]
ON, OFF
VIR. SPEAKERS [xxx]
ON, OFF
4-Tuner
Settings
FM MODE [xxxxxx]
NAME IN? [xxx]
MONO, STEREO
page 90
5-Audio
Settings
DEC. PRIORITY [xxxx]
PCM, AUTO
AUTO
MAIN
0ms
page 64
DUAL MONO
[xxxxxxxx]
MAIN/SUB, MAIN, SUB,
MAIN+SUB
A/V SYNC [xxxms]
DIGITAL ASSIGN ?
0ms to 150ms/300ms (10 ms step)
page 92
page 90
page 94
page 93
page 65
NAME IN ? [xxx]
6-Video
Settings
COMPONENT V. ASSIGN ?
HDMI VIDEO ASSIGN ?
HDMI AUDIO [xxxxxx] AMP, TV+AMP
AMP
HDMI POWER
AUTO, EVER ON
AUTO
[xxxxxxx]
VIDEO CONVERT [xxx]
ON, OFF
ON
PROGRESSIVE OUT [xxx] ON, OFF
OFF
NAME IN ?
page 90
[xxxxxxxx]
56GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu
Item
Parameter
Initial
setting page
Refer
7-Speaker
Settings
SUB WOOFER [xxx]
FRONT SP [xxxxx]
CENTER SP [xxxxx]
NO, YES
YES
page 66
SMALL, LARGE
MIX, NO, SMALL, LARGE
LARGE
LARGE
LARGE
DUAL
SURROUND SP [xxxxx] NO, SMALL, LARGE
SUR BACK SP [xxxxxx] BI-AMP, ZONE 2, NO, SINGLE,
DUAL
FRONT L xxfeet*
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
3feet to 22feet (1 foot** step)
meter, feet
9feet
9feet
9feet
9feet
9feet
9feet
9feet
9feet
feet
FRONT R xxfeet*
CENTER xxfeet*
SURROUND L xxfeet*
SURROUND R xxfeet*
SUR BACK L xxfeet*
SUR BACK R xxfeet*
SUB WOOFER xxfeet*
DISTANCE UNIT
[xxxxx]
SP POSI [xxxxxxxxx] SIDE/LOW, SIDE/HIGH, BEHD/
SIDE/
LOW
LOW, BEHD/HIGH
SP CROSSOVER [xxxHz] 40Hz to 200Hz (10Hz step)
DIMMER [xxx% DOWN] 0%, 60%, 100%
SP. IMPEDANCE [xxxx] 4 ohm, 8 ohm
AUTO CAL START?
120Hz
0%
8-System
Settings
page 70
page 39
8 ohm
9-Auto
Calibration
page 46
CAL TYPE
[xxxxxxxxx]
ENGINEER/FULL FLAT/FRONT
REF
FULL FLAT
OFF
EQ CURVE EFFECT [xxx] OFF, ON
A.CAL LOAD? [PRESET- x] OFF, PRESET1, PRESET2, PRESET3 OFF
A.CAL SAVE? [PRESET- x] PRESET1, PRESET2, PRESET3
PRESET1
A.CAL NAME?
page 90
[xxxxxxxxx]
*
After the measurements are completed using auto calibration, the measurement value is displayed as
x’xx”.
** After the measurements are completed using auto calibration, you can adjust them in 1 inch increments.
57GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x CENTER
(Center speaker level)
Adjusting the level (Level
Settings menu)
x SURROUND L
(Surround speaker (L) level)
You can use the Level Settings menu to adjust
the balance and level of each speaker. These
settings are applied to all sound fields. Select
“Level Settings” in the setting menus. For
details on adjusting the parameters, see
x SURROUND R
(Surround speaker (R) level)
x SUR BACK
(Surround back speaker level)
Only when the surround back speakers are set
to “SINGLE” in the System Settings menu
Level Settings menu parameters
x SUR BACK L
(Surround back (L) level)
Only when the surround back speakers are set
to “DUAL” in the System Settings menu (page
67).
x TEST TONE (Test Tone)
Lets you output the test tone sequentially from
each speaker.
• OFF
• AUTO
x SUR BACK R
The test tone is output from each speaker.
• FIX
You can select which speakers will output
the test tone.
(Surround back (R) level)
Only when the surround back speakers are set
to “DUAL” in the System Settings menu (page
67).
x SUB WOOFER
x PHASE NOISE (Phase noise)
• ON
(Sub woofer level)
Lets you output the test tone sequentially
from adjacent speakers.
• OFF
Note
When one of the sound fields for music is selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” on the Speaker
Settings menu. However, the sound will be output
from the sub woofer if the digital input signal
contains L.F.E. signals, the front or surround
speakers are set to “SMALL,” the sound field for
movie is selected, or “PORTABLE AUDIO” is
selected.
x PHASE AUDIO (Phase audio)
• ON
Lets you output front 2 channel source sound
(instead of the test tone) sequentially from
adjacent speakers.
• OFF
Note
x MULTI CH SW
The HDMI sound is not output when you display the
receiver’s menu on the TV monitor.
(Multi-channel sub woofer level)
Lets you increase the level of the MULTI
CHANNEL INPUT sub woofer channel
signals by +10 dB. This adjustment may be
necessary when connecting a DVD player to
the MULTI CHANNEL INPUT jacks. The sub
woofer level from DVD players is 10 dB lower
than that of Super Audio CD players.
x FRONT BAL.
(Front speaker balance)
Lets you adjust the balance between front left
and right speakers.
58GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x D.RANGE COMP.
(Dynamic range compressor)
Lets you compress the dynamic range of the
sound track. This may be useful when you
want to watch movies at low volumes late at
night. Dynamic range compression is possible
with Dolby Digital sources only.
• OFF
The dynamic range is not compressed.
• STD
The dynamic range is compressed as
intended by the recording engineer.
• MAX
Adjusting the equalizer
(EQ Settings menu)
You can use the EQ Settings menu to adjust the
tonal quality (bass/treble level) of the front
speakers and to store up to 5 different
equalizer settings in the equalizer preset (EQ
PRESET [1]-[5]) and apply them. These
settings are applied to all sound fields and for
each speaker. Select “EQ Settings menu” in
the system menus. For details on adjusting the
55).
The dynamic range is compressed
dramatically.
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
Bass
Treble
Level
(dB)
“STD” is the standard setting, but it only enacts light
compression. Therefore, we recommend using the
“MAX” setting. This greatly compresses the
dynamic range and lets you view movies late at night
at low volumes. Unlike analog limiters, the levels are
predetermined and provide a very natural
compression.
Frequency
(Hz)
Notes
• This function does not work in the following cases.
– MULTI IN is selected.
– Input signals of which the sampling frequency is
more than 96 kHz are being received.
• If you set up the sound field during DTS 96/24
signal reception, it will play back only at 48 kHz.
EQ Settings menu parameters
x EQ PRESET
(Preset equalizer selection)
Lets you select the equalizer preset ([1]-[5]).
When you select “OFF,” the equalizer is
cancelled.
x FRONT BASS*
(Front speaker bass level)
x FRONT TREBLE*
(Front speaker treble level)
*
You can adjust the front speaker bass and treble
level with TONE MODE and TONE on the
receiver.
continued
59GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press V/v repeatedly to select “YES,”
then press
x CENTER BASS
(Center speaker bass level)
.
“Are you sure?” appears on the display.
x CENTER TREBLE
5 Press V/v repeatedly to select “YES,”
(Center speaker treble level)
then press
.
x SUR/SB BASS
“PRESET x CLEARED!” appears on the
display and the adjusted contents of the
selected equalizer preset are cleared.
(Surround/surround back
speaker bass level)
x SUR/SB TREBLE
(Surround/surround back
speaker treble level)
x PRESET x CLEAR
(Equalizer preset clear)
You can reset the adjusted equalizer settings to
the initial setting. For details, see “Clearing
To apply the stored equalizer
Settings” in step 3.
2 Press V/v repeatedly to select the
equalizer (EQ PRESET [1]-[5]) you
want to apply, then press
to enter.
To turn off the equalizer
Select “OFF” in the “EQ PRESET” setting.
Clearing stored equalizer
settings
Settings” in step 3.
2 Press V/v repeatedly to select the
equalizer (EQ PRESET [1]-[5]) you
want to clear, then press
to enter.
3 Press V/v repeatedly to select
“PRESET x CLEAR.”
“x” is the number of the selected equalizer
preset.
60GB
Download from Www.Somanuals.com. All Manuals Search And Download.
You can adjust the distribution of the center
channel signal, generated through the Dolby
Pro Logic II decoding, to the left/right
speakers.
Settings for the surround
sound (Sur Settings menu)
x DIMENSION
You can use the Sur Settings menu to select the
sound field you want for your listening
pleasure. Select “Sur Settings” in the setting
menus. For details on adjusting the
parameters, see “Navigating through menus”
55).
(Dimension control)
Lets you perform further adjustments for
Dolby Pro Logic II and IIx Music mode
decoding. You can set this parameter only
when A.F.D. mode is set to “PRO LOGIC II
MUSIC” or “PRO LOGIC IIx MUSIC” (page
73).
You can adjust the difference between the front
channels and the surround channels.
Sur Settings menu parameters
x PANORAMA MODE
(Panorama mode)
x SOUND FIELD SELECT?
(Sound field type selection)
Lets you select the sound field you want. For
72).
Lets you perform further adjustments for
Dolby Pro Logic II and IIx Music mode
decoding. You can set this parameter only
when A.F.D. mode is set to “PRO LOGIC II
MUSIC” or “PRO LOGIC IIx MUSIC” (page
73).
x SB DECODING
(Surround back decoding)
Lets you select the surround back decoding
function. For details, see “Using the surround
• ON
Lets you enjoy surround sound by spreading
the sound field of the front speakers to the
left and right of the listening position
(panorama mode).
x SB DEC MODE
• OFF
(Surround back decoding mode)
Lets you select the surround back decoding
mode. For details, see “Using the surround
Panorama mode is not activated.
x SCREEN DEPTH
(Screen depth)
This parameter is provided especially for
Lets you create the sensation that the sound of
the front speakers comes from inside the
screen in your listening room, just like in
theaters.
x EFFECT LEVEL
(Effect level)
Higher settings apply more surround effect.
x CENTER WIDTH
• ON
(Center width control)
Lets you create a sound environment where
you will feel the sound comes directly out of
a large screen in front of you.
• OFF
Lets you perform further adjustments for
Dolby Pro Logic II and IIx Music mode
decoding. You can set this parameter only
when A.F.D. mode is set to “PRO LOGIC II
MUSIC” or “PRO LOGIC IIx MUSIC” (page
73).
This function is not activated.
continued
61GB
Download from Www.Somanuals.com. All Manuals Search And Download.
e)
When two surround back speakers are connected,
the output channel will be 7.1 channel signals.
x VIR.SPEAKERS
(Virtual speakers)
This parameter is provided especially for
• ON
• ON
The SB DEC MODE setting is applied to 5.1
channel and 6.1 channel decoding in the
input stream.
Virtual speakers are created.
• OFF
• OFF
Surround back decoding is not performed.
Virtual speakers are not created.
Notes
Using the surround back
decoding mode (SB DECODING)
• This function does not work in the following cases.
– MULTI IN is selected.
– The sound field for music or movie is selected.
– DTS 96/24 signals are being received.
– The multi-channel PCM signals are received via
an HDMI IN jack.
• There may be no sound from the surround back
speaker in Dolby Digital EX mode. Some discs
have no Dolby Digital Surround EX flag even
though the packages have Dolby Digital EX logos.
In this case, select “ON.”
By decoding the surround back signal of DVD
software (etc.) recorded in Dolby Digital
Surround EX, DTS-ES Matrix, DTS-ES
Discrete 6.1, etc., format, you can enjoy the
surround sound intended by the filmmakers.
x SB DECODING
• AUTO
• When “PLIIx” is selected, SB DECODING is set
to the PLIIx mode.
When the input stream contains the 6.1
channel decode flag , the appropriate
a)
decoding is performed on the surround back
signal.
x SB DEC MODE
You can select surround back decoding mode
only when “SB DECODING” is set to “ON”
or “AUTO” and the input stream contains the
Dolby Digital Surround EX flag.
Input stream Output Surround back
channels decoding
e)
Dolby Digital
5.1
5.1
—
SB DEC
MODE
Speaker Surround back
setting decoding
e)
Dolby Digital
Surround EX
6.1
Matrix decoder that
conforms to Dolby
b)
[DDEX]
7.1
Matrix decoder conforms
channels to Dolby Digital EX
e)
e)
DTS 5.1
DTS-ES
5.1
6.1
—
6.1
Matrix decoder conforms
DTS Matrix decoding
channels to Dolby Digital EX
c)
Matrix 6.1
[PLIIx MV] 7.1
Movie decoder conforms
e)
DTS-ES
Discrete 6.1
6.1
DTS Discrete
decoding
channels to Dolby Pro Logic IIx
d)
6.1 Matrix decoder conforms
channels to Dolby Digital EX
a)
b)
A 6.1 channel decode flag is information recorded
in software, such as DVDs.
A Dolby Digital DVD that includes a Surround EX
flag. The Dolby Corporation web page can help
you distinguish Surround EX films.
Software encoded with a flag to denote it has both
DTS-ES Matrix and 5.1 channel signals.
Software encoded with both 5.1 channel signals
and an extension stream designed for returning
those signals to 6.1 discrete channels. Discrete 6.1
channel signals are DVD specific signals not used
in movie theaters.
[PLIIx MS] 7.1
Music decoder conforms
channels to Dolby Pro Logic IIx
6.1
Music decoder conforms
c)
d)
channels to Dolby Pro Logic IIx
62GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Matrix decoding conforming to Dolby Digital EX
is applied regardless of the surround back decoder
mode setup when a sound field for a movie is
selected.
Settings for the tuner
(Tuner Settings menu)
• Matrix decoding conforming to Dolby Digital EX
is applied if the speaker setting is 6.1 channel
system and movie decoding conforming to Pro
Logic IIx is applied if the speaker setting is 7.1
channel system, when you select Dolby PLIIx MS
under the following conditions:
You can use the Tuner Settings menu to set the
FM station receiving mode and to name preset
stations.
Select “Tuner Settings” in the Setting menus.
For details on adjusting the parameters, see
– a Dolby Digital Surround EX signal is input
– “SB DECODING” is set to “AUTO”
Tuner Settings menu parameters
x FM MODE
(FM station receiving mode)
• STEREO
This receiver will decode the signal as stereo
signal when the radio station is broadcast in
stereo.
• MONO
This receiver will decode the signal as mono
signal regardless of the broadcast signal.
x NAME IN?
(Naming preset stations)
Lets you set the name of preset stations. For
63GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• MAIN/SUB
Sound of the main language will be output
through the front left speaker, and sound of
the sub language will be output through the
front right speaker simultaneously.
• MAIN
Sound of the main language will be output.
• SUB
Sound of the sub language will be output.
• MAIN+SUB
Settings for the audio
(Audio Settings menu)
You can use the Audio Settings menu to make
settings for the audio to suit your preference.
Select “Audio Settings” in the setting menus.
For details on adjusting the parameters, see
Mixed sound of both the main and sub
languages will be output.
Audio Settings menu parameters
x A/V SYNC
(Synchronizes audio and video
output)
x DEC. PRIORITY
(Digital audio input decoding
priority)
Lets you delay the output of audio to minimize
the time gap between audio output and visual
display.
Lets you specify the input mode for the digital
signal input to the DIGITAL IN and HDMI IN
jacks.
Notes
• This function is useful when you use a large
LCD or plasma monitor or a projector.
• This function is not valid when
• AUTO
Automatically switches the input mode
between DTS, Dolby Digital, or PCM.
• PCM
– MULTI IN is selected.
– Input signals of which the sampling frequency is
more than 96 kHz are being received.
– The multi-channel PCM signals are received via
an HDMI IN jack.
– ANALOG DIRECT function is being used.
– “NEURAL SURROUND” is selected as the
sound field type.
• You can adjust the delay to up to 300ms
– the sampling frequency is less than 48 kHz
– 2 channel analog signals
• You can adjust the delay to up to 150ms
– the sampling frequency is 88.2 kHz or 96 kHz
Although the parameter appears up to 300ms at this
time, you cannot adjust the delay by more than
150ms.
When signals from the DIGITAL IN jack are
selected, PCM signals are given priority (to
prevent interruption when playback starts).
However, when other signals are input, there
may be no sound, depending on the format.
In this case, set this item to “AUTO.”
When signals from the HDMI IN jack are
selected, only PCM signals are output from
the connected player. When signals in any
other format are received, set this item to
“AUTO.”
Note
When set to “AUTO” and the sound from the digital
audio jacks (for a CD, etc.) is interrupted when
playback starts, set to “PCM.”
x DIGITAL ASSIGN?
(Digital audio input assignment)
Lets you assign the digital audio input to other
input source. For details, see “Listening to
x DUAL MONO
(Digital broadcast language
selection)
Lets you select the language you want to listen
to during a digital broadcast. This feature only
functions for Dolby Digital sources.
x NAME IN? (Naming inputs)
Lets you set the name of inputs selected. For
64GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• AMP
The HDMI audio signals from the playback
component is only output to speakers
connected to the receiver. Multi-channel
sound can be played back as it is.
Settings for the video
(Video Settings menu)
You can use the Video Settings menu to
reassign the component video input to another
input and to name inputs. Select “Video
Settings” in the setting menus. For details on
adjusting the parameters, see “Navigating
Note
Audio signals are not output from the TV’s
speakers.
x HDMI POWER
(Power management of the HDMI
circuit)
• AUTO
Lets you turn off the power of unnecessary
HDMI circuits automatically. You can enjoy
high quality digital or analog audio without
the influence of the HDMI circuits. When
set to “AUTO,” it takes some time to output
the sound.
Video Settings menu parameters
x COMPONENT V. ASSIGN?
(Component Video Assign)
Lets you reassign the component video input
to another visual input. For details, see
• EVER ON
Lets you keep the power of the HDMI
circuits. Select this setting if you do not like
the time lag that occurs with the “AUTO”
setting. It may be ineffective depending on
the component.
x HDMI VIDEO ASSIGN?
(HDMI Video Assign)
Lets you reassign the HDMI video input to
another visual input. For details, see
x VIDEO CONVERT*
(Conversion of video signals)
• ON
• OFF
x HDMI AUDIO
This function is not activated.
(Setting HDMI audio input)
Lets you set the HDMI audio output from the
playback component connected to the receiver
via an HDMI connection.
x PROGRESSIVE OUT*
(Progressive conversion of the
video signals)
• ON
• TV+AMP
Lets you output a video signal, which is
converted 480p component video signals
when the video signal is output as
component video signals.
The sound is output from TV’s speaker and
the speakers connected to the receiver.
Notes
• The sound quality of the playback component
depends on the TV’s sound quality, such as the
number of channels, and the sampling frequency,
etc. When the TV has stereo speakers, the sound
output from the receiver is also stereo as that of
the TV, even if you play multi-channel software.
• When you connect the receiver to a video
component (projector, etc.), sound may not be
output from the receiver. In this case, select
“AMP.”
Note
Only 480i component video input signals are
accepted.
• OFF
This function is not activated.
continued
65GB
Download from Www.Somanuals.com. All Manuals Search And Download.
*
Each video input can be adjusted independently
for every INPUT SELECTOR. The adjusted value
is held until the memory of this receiver is cleared.
The adjusted value is retained, even if the power is
turned off or the power cord (mains lead) is pulled
out.
Settings for the speakers
(Speaker Settings menu)
You can use the Speaker Settings menu to set
the size and distance of the speakers connected
to this system. Select “Speaker Settings” in the
setting menus. For details on adjusting the
55).
x NAME IN? (Naming inputs)
Lets you set the name of inputs selected. For
Speaker Settings menu
parameters
x SUB WOOFER (Sub woofer)
• YES
If you have connected a sub woofer, select
“YES.”
• NO
If you have not connected a sub woofer,
select “NO.” This activates the bass
redirection circuitry and outputs the L.F.E.
(Low Frequency Effect) signals from other
speakers.
Tip
In order to take full advantage of the Dolby Digital
bass redirection circuitry, we recommend setting the
sub woofer’s cut off frequency as high as possible.
x FRONT SP (Front speakers)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies,
select “LARGE.” Normally, select
“LARGE.” When the sub woofer is set to
“NO,” front speakers are automatically set to
“LARGE.”
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi-channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL,” the center, surround, and
66GB
Download from Www.Somanuals.com. All Manuals Search And Download.
surround back speakers are also
automatically set to “SMALL” (unless
previously set to “NO”).
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
x CENTER SP (Center speaker)
• LARGE
If you have not connected surround
speakers, select “NO.”
If you connect a large speaker that will
effectively reproduce bass frequencies,
select “LARGE.” Normally, select
“LARGE.” However, if the front speakers
are set to “SMALL,” you cannot set the
center speaker to “LARGE.”
x SUR BACK SP
(Surround back speakers)
When the surround speakers are set to “NO,”
the surround back speakers are also
automatically set to “NO” and the setting
cannot be changed.
• SMALL
• DUAL
If the sound is distorted, or you feel a lack of
surround effects when using multi-channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the
front speakers (if set to “LARGE”) or sub
woofer.
If you connect two surround back speakers,
select “DUAL.” The sound will be output to
a maximum of 7.1 channels.
• SINGLE
If you connect only one surround back
speaker, select “SINGLE.” The sound will
be output to a maximum of 6.1 channels.
• NO
• NO
If you have not connected a center speaker,
select “NO,” the sound of the center channel
will be output from the front speakers.
• MIX
If you have not connected surround back
speakers, select “NO.”
• ZONE 2
If you use the surround back speaker in zone
2, select “ZONE 2.” When you select
“ZONE 2,” the input to the SURROUND
BACK jacks of the MULTI CHANNEL
• BI-AMP
If you connect front speakers in a bi-
amplifier configuration, select “BI-AMP”
If you have not connected a center speaker,
select “MIX.” The sound of the center
channel will be output without affecting
sound quality. You can assign the sound for
the center speaker output to the front speaker
output by changing the setting of
“CENTER” in Level Settings menu.
x SURROUND SP
(Surround speaker)
Tip
The surround back speakers will be set to the
same setting.
The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sound has a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies,
select “LARGE.” Normally, select
“LARGE.” However, if the front speakers
are set to “SMALL,” you cannot set the
surround speakers to “LARGE.”
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi-channel
surround sound, select “SMALL” to activate
continued
67GB
Download from Www.Somanuals.com. All Manuals Search And Download.
bass frequencies output from that speaker, set it to
“SMALL.”
x CENTER
(Center speaker distance)
Lets you set the distance from your listening
position to the center speaker.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE.” If there is not enough
bass, you can use the equalizer to boost the bass
levels. For details, see “Adjusting the equalizer (EQ
x SURROUND L
(Surround left speaker distance)
x FRONT L
x SURROUND R
(Front left speaker distance)
(Surround right speaker
distance)
x FRONT R
Lets you set the distance from your listening
position to the surround speakers.
If both surround speakers are not placed an
equal distance from your listening position, set
the distance to the closest speaker.
(Front right speaker distance)
Lets you set the distance from your listening
position to the front speakers (A).
If both front speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
x SUR BACK L
(Surround back left speaker
distance)
With only one surround back
speaker
x SUR BACK R
(Surround back right speaker
distance)
Lets you set the distance from your listening
position to the surround back speaker.
If you connect two surround back speakers and
both surround back speakers are not placed an
equal distance from your listening position, set
the distance to the closest speaker.
x SUB WOOFER
(Sub woofer distance)
Lets you set the distance from your listening
position to the sub woofer.
With two surround back speakers
(The angle B should be the same)
Tips
• If you set up speakers using the auto calibration
function, you can adjust the speaker distance in 1
cm (1 inch) increment.
• The distance between the center speaker and the
listening position B cannot be more than 1.5
meters (5 feet) closer than the one between the
listening position and the front speaker A. Place
the speakers so that the difference in the length of
B in the following diagram is no more than 1.5
meters (5 feet) closer than the length of A.
Example: Adjust the distance B to 4.5 meters (15
feet) or more when the distance A is 6 meters (20
feet).
68GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Also, the distance between the surround speakers/
surround back speakers and the listening position
C cannot be more than 4.5 meters (15 feet) closer
than the distance between the listening position
and the front speakers A. Place the speakers so
that the difference in the length of C in the
following diagram is no more than 4.5 meters (15
feet) closer than the length of A.
x SP POSI.
(Surround speaker position)
Lets you specify the location of your surround
speakers for proper implementation of the
surround effects in the Cinema Studio EX
available when the surround speakers are set to
Example: Adjust the distance C to 1.5 meters (5
feet) or more when the distance A is 6 meters (20
feet).
This is important because incorrect speaker
placement is not conductive to the enjoyment of
surround sound. Place note that placing the
speakers closer than the required will cause a delay
in the output of the sound from that speaker. In
other words, the speaker will sound like it is farther
away.
x DISTANCE UNIT (Distance unit)
Lets you select the unit of measure for setting
distances.
• feet
The distance is displayed in feet.
• meter
The distance is displayed in meters.
• SIDE/LOW
Select if the location of your surround
speakers corresponds to sections A and C.
• SIDE/HIGH
Select if the location of your surround
speakers corresponds to sections A and D.
• BEHD/LOW
Select if the location of your surround
speakers corresponds to sections B and C.
• BEHD/HIGH
Select if the location of your surround
speakers corresponds to sections B and D.
continued
69GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Surround speaker position is designed specifically
for implementation of the Cinema Studio EX modes.
For other sound fields, speaker position is not so
critical.
Settings for the system
(System Settings menu)
Those sound fields were designed under the premise
that the surround speakers would be located behind
the listening position, but presentation remains fairly
consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects become unclear unless set to
“SIDE.”
Nevertheless, each listening environment has many
variables, such as wall reflections, and you may
obtain better results using “BEHD” if your speakers
are located high above the listening position, even if
they are located to the immediate left and right.
Therefore, although it may result in a setting
contrary to the above explanation, we recommend
that you playback multi-channel surround encoded
software and select the setting that provides a good
sense of spaciousness and that best succeeds in
forming a cohesive space between the surround
sound from the surround speakers and the sound of
the front speakers. If you are not sure which sounds
best, select “BEHD” and then use the speaker
distance parameter and speaker level adjustments to
obtain proper balance.
You can use the System Settings menu to
customize the settings of the receiver. Select
“System Settings” in the setting menus. For
details on adjusting the parameters, see
System Settings menu
parameters
x DIMMER
(Brightness of the display)
Lets you adjust the brightness of the display.
When you choose setting such that you turn off
the display completely, the MULTI
CHANNEL DECODING indicator is also
turned off.
x SP. IMPEDANCE
(Speaker impedance)
39).
x SP CROSSOVER
(Speaker crossover frequency)
Lets you set the bass crossover frequency of
speakers that has been set to “SMALL” in the
System Settings menu. You cannot set “SP
CROSSOVER” when setting speakers using
the auto calibration function. To adjust the
speaker crossover, set “A.CAL LOAD ?” to
“OFF” in the Auto Calibration menu. Then, set
up the speakers manually, and select the
parameter from “SP CROSSOVER.”
70GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibrating the
appropriate settings
automatically (Auto
Calibration menu)
For details, see “7: Calibrating the appropriate
71GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
• We usually recommend “A.F.D. AUTO,” however
sometimes it may be better to use “SB
to the mode you prefer.
• You can identify the encoding format of DVD
software, etc., by looking at the logo on the
package.
Enjoying Surround Sound
Enjoying Dolby Digital
and DTS surround sound
(A.F.D. mode)
–
–
: Dolby Digital discs
: Dolby
Surround encoded programs
The A.F.D. (Auto Format Direct) mode allows
you to listen to higher fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi-channel sound.
–
: DTS Digital Surround encoded programs
• Only Dolby Pro Logic IIx decoding is effective,
when a multi-channel signal is input.
At this time, the setup of “SB DECODING” and
“SB DEC MODE” in the Sur Settings menu
becomes invalid. When you select decoding modes
other than Dolby Pro Logic IIx, multi-channel
sound (being encoded) is output.
If you connect a sub woofer
This receiver will generate a low frequency
signal for output to the sub woofer when there
is no L.F.E. signal, which is a low-pass sound
effect output from a sub woofer to a 2 channel
signal. However, the low frequency signal is
not generated for “Neo:6 Cinema” or “Neo:6
Music” when all speakers are set to “LARGE.”
A.F.D.
Press A.F.D. repeatedly to select
the sound field you want.
73).
You can also select “A.F.D.” in the Sur Settings
menu. For details, see “Settings for the
61).
Notes
• This function does not work in the following cases.
– MULTI IN is selected.
– Input signals of which the sampling frequency is
more than 48 kHz are being received.
– The multi-channel PCM signals are received via
an HDMI IN jack.
• If you set up the sound field during DTS 96/24
signal reception, it will play back only at 48 kHz.
• NEURAL SURROUND is activated as a PCM
signal of which the sampling frequency is less than
48 kHz or a 2 channel analog signal. The NEURAL
SURROUND processing will be turned off
automatically when another type of signal is input.
The beginning of the sound may be dropped out
when the SURROUND processing is turned on/off.
72GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Type of A.F.D. mode
A.F.D. mode
Multi-channel audio after Effect
decoding
A.F.D. AUTO
PRO LOGIC
(Detecting automatically)
Presets the sound as it was recorded/encoded
without adding any surround effects.
4-channel signals
Performs Dolby Pro Logic decoding. The
source recorded in 2 channel format is decoded
into 4.1 channels.
PRO LOGIC II MOVIE
5-channel signals
5-channel signals
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In Addition, this
mode can reproduce sound in 5.1 channel
system for watching videos of overdubbed or
old movies.
PRO LOGIC II MUSIC
Performs Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal stereo
sources such as CDs.
PRO LOGIC II GAME
5-channel signals
7-channel signals
Performs Dolby Pro Logic II Game mode
decoding.
PRO LOGIC IIx MOVIE*
Performs Dolby Pro Logic IIx Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition, this
mode can reproduce sound in 7.1 channel
system for watching videos of overdubbed or
old movies.
PRO LOGIC IIx MUSIC*
PRO LOGIC IIx GAME*
7-channel signals
7-channel signals
Performs Dolby Pro Logic IIx Music mode
decoding. This setting is ideal for normal stereo
sources such as CDs.
Performs Dolby Pro Logic IIx Game mode
decoding.
Neo:6 Cinema
Neo:6 Music
6-channel signals
6-channel signals
Performs DTS Neo:6 Cinema mode decoding.
Performs DTS Neo:6 Music mode decoding.
This setting is ideal for normal stereo sources
such as CDs.
MULTI STEREO
7-channel signals
7-channel signals
Outputs 2 channel left/right signals from all
speakers.
NEURAL SURROUND
The receiver outputs signals in the multi-
channel surround format when the receiver
receives PCM signals of 2 channels or an XM
Radio surround broadcast. When the receiver
receives a stereo broadcast, the stereo sound is
emphasized.
*
You cannot select this decoding mode if there are no surround back speakers connected to the receiver.
73GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• When one of the sound fields for music is selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” in the System
Settings menu. However, the sound will be output
from the sub woofer if the digital input signal
contains L.F.E. signals, the front or surround
speakers are set to “SMALL,” the sound field for
movie is selected, or “PORTABLE AUDIO” is
selected.
Selecting a pre-
programmed sound field
(DCS)
You can take advantage of surround sound
simply by selecting one of the receiver’s
preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
• The surround back decoding mode does not
function while a sound field for music is selected
Tips
• Sound fields with DCS marks use DCS
• When the sound field’s DCS mark is selected,
the Digital Cinema Sound lamp lights up on the
display.
A.F.D.
2CH
MOVIE
MUSIC
To turn off the surround effect
for MOVIE/MUSIC
Press 2CH to select “2CH STEREO” or press
A.F.D. repeatedly to select “A.F.D. AUTO.”
Press MOVIE repeatedly to select a
sound field for movies or press
MUSIC repeatedly to select a sound
field for music.
The sound field list appears.
You can also select “MOVIE” or “MUSIC” in
the Sur Settings menu. For details, see
Notes
• The sound fields for music and movie do not work
in the following cases.
– MULTI IN is selected.
– Input signals of which the sampling frequency is
more than 48 kHz are being received.
– The multi-channel PCM signals are received via
an HDMI IN jack.
• If you set up the sound field during DTS 96/24
signal reception, it will play back only at 48 kHz.
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
74GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of sound field available
Sound field
for
Sound field
Effect
Movie
CINEMA STUDIO EX A
DCS
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Cary Grant Theater” cinema production
studio. This is a standard mode, great for watching almost any
type of movie.
CINEMA STUDIO EX B
DCS
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Kim Novak Theater” cinema production
studio. This mode is ideal for watching science-fiction or
action movies with lots of sound effects.
CINEMA STUDIO EX C
DCS
Reproduces the sound characteristics of the Sony Pictures
Entertainment scoring stage. This mode is ideal for watching
musicals or films where orchestra music is featured in the
soundtrack.
V.MULTI DIMENSION
DCS
Creates 5 sets of virtual speakers from a single pair of actual
surround speakers.
Music
HALL
Reproduces the acoustics of a classical concert hall.
Reproduces the acoustics of a jazz club.
JAZZ CLUB
LIVE CONCERT
STADIUM
Reproduces the acoustics of a 300-seat live house.
Reproduces the feeling of a large open-air stadium.
Reproduces the feeling of sports broadcasting.
SPORTS
PORTABLE AUDIO
Reproduces a clear enhanced sound image from your portable
audio device. This mode is ideal for MP3 and other
compressed music.
Headphone*
HEADPHONE (2CH)
This mode is selected automatically if you use headphones
is selected. Standard 2 channel stereo sources completely
bypass the sound field processing and multi-channel surround
formats are downmixed to 2 channels.
HEADPHONE THEATER This mode is selected automatically when you use headphones
DCS
when sound field is selected for movie/music. It allows you to
experience a theater-like environment while listening through
a pair of headphones.
HEADPHONE (DIRECT) Outputs the analog signals without processing by the tone,
sound field, etc.
HEADPHONE (MULTI)
This mode is selected automatically if you use headphones
when MULTI IN is selected. Outputs the front analog signals
from the MULTI CHANNEL INPUT jacks.
*
You can select this sound field mode if the headphones are connected to the receiver.
75GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using only the front
speakers
Enjoying the surround
effect at low volume
levels
(2CH STEREO)
(NIGHT MODE)
In this mode, the receiver outputs the sound
from the front left/right speakers only. There is
no sound from the sub woofer.
Standard 2 channel stereo sources completely
bypass the sound field processing and multi-
channel surround formats are downmixed to 2
channel.
This function allows you to retain a theater like
environment at low volume levels. This
function can be used with other sound fields.
When watching a movie late at night, you will
be able to hear the dialog clearly even at a low
volume level.
1
2CH
Press 2CH.
Note
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to 2 channel stereo sources
using the front left/right speakers and a sub woofer,
select “A.F.D. AUTO.”
This receiver will generate a low frequency signal
for output to the sub woofer when there is no L.F.E.
signal, which is a low-pass sound effect output from
a sub woofer to a 2 channel signal.
2
1 Press RECEIVER.
Receiver operation is enabled.
2 Press NIGHT MODE.
The NIGHT MODE function is activated.
The NIGHT MODE is toggled between
on and off as you press NIGHT MODE.
76GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• This function does not work in following cases.
– MULTI IN is selected.
Listening to the sound
without any adjustment
(ANALOG DIRECT)
– Input signals of which the sampling frequency is
more than 96 kHz are being received.
• If you set the NIGHT MODE to on during DTS 96/
24 signal reception, it will play back only at 48
kHz.
You can switch the audio of the selected input to 2
channel analog input. This function enables you to
enjoy high quality analog sources.
When using this function, only the volume and front
speaker balance can be adjusted.
Tip
While this function is on, the BASS, TREBLE, and
EFFECT levels increase, and “D.RANGE COMP.”
A.DIRECT
Press A.DIRECT.
Analog audio is output. ANALOG DIRECT
function is toggled between on and off as you press
A.DIRECT.
To enjoy the analog sound
source with noise free
performance (Analog pureness
control)
The Analog pureness control function by-
passes the video and digital circuits that are not
in use, and shuts down the power while the
analog source is being played back. Thus, the
Analog pureness control function provides
noise-free audio performance and delivers
high sound quality.
The Analog pureness control function is
activated when you select an input source with
no video input, then select “ANALOG” from
INPUT MODE, and you press ANALOG
DIRECT.
77GB
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press V/v repeatedly to select
“Level Settings,” then press
to enter.
Adjusting the speaker
levels and balance
(TEST TONE)
6 Press V/v repeatedly to select
“TEST TONE,” then press
.
You can adjust the speaker levels and balance
while listening the test tone from your
listening position.
7 Press V.
The test tone is output from each speaker
in sequence.
Also, if you press v, the pattern will
become the “FIX” pattern in which the
test tone is output from the selected
speaker only.
Tip
The receiver employs a test tone with a frequency
centered at 800 Hz.
8 Press
to enter.
1
3
9 Adjust the speaker level and
balance using the Level
Settings menu so that the level
of the test tone sounds the
same from each speaker.
For details on the Level Settings menu,
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/–.
• The adjusted value is shown on the display
during adjustment.
2,
5-11
12
10Press V/v repeatedly to select
“TEST TONE,” then press
.
4
11Press v to select “OFF,” then
press
.
The test tone turns off.
1 Turn on the receiver and TV.
12Press ON SCREEN.
2 Press ON SCREEN.
The menu setting display disappears.
Switch the input of the TV so that the
setting menu is displayed on the TV
screen connected to this receiver.
3 Press RECEIVER.
Receiver operation is enabled.
4 Press MENU.
The list of setting menus appears.
78GB
Download from Www.Somanuals.com. All Manuals Search And Download.
When a test tone is not output
from the speakers
• The speaker cords may not be connected
securely. Check to see if they are connected
securely and cannot be disconnected by
pulling on them slightly.
Resetting sound fields to
the initial settings
1,2
2
• The speaker cords may have the short-circuit
problem.
When a test tone is output from
a different speaker than the
speaker displayed screen
The location where you set up the speaker (for
example, the front speaker position) and type
of the speaker terminal you connected (for
example, the surround back speaker terminal)
are different. Check the speaker allocation.
1 Press POWER to turn off the
power.
2 While holding down MUSIC,
For more precise adjustment
You can output the test tone or sound source
from two adjacent speakers to adjust their
balance and level.
press POWER.
“S.F. Initialize” appears on the display
and all sound fields are reset to their
initial setting.
Then select the two speakers you want to
adjust by selecting “PHASE NOISE” or
“PHASE AUDIO” in step 6.
79GB
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of poor FM stereo
reception
If the FM stereo reception is poor and
“STEREO” flashes on the display, select
monaural audio so that the sound will be less
distorted.
Tuner Operations
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
antennas (aerials) to the receiver (page 36).
Select “MONO” in “FM MODE” selection in
Tip
The tuning scale for direct tuning is shown below.
• FM band 100 kHz
• AM band 10 kHz*
* The AM tuning scale can be changed (page 120).
Automatic tuning
1
2
1 Press TUNER repeatedly to
select the FM or AM band.
2 Press TUNING +/–.
Press TUNING + to scan from low to
high, press TUNING – to scan from high
to low.
The receiver stops scanning whenever a
station is received.
80GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting radio stations
Direct tuning
Enter the frequency of a station directly by
using the numeric buttons.
You can preset up to 30 FM and 30 AM
stations. Then you can easily tune in the
stations you often listen to.
1
Presetting radio stations
1
3
2
4
1 Press TUNER repeatedly to
select the FM or AM band.
3,5
2 Press D.TUNING.
3 Press the numeric buttons to
enter the frequency.
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
4 Press ENTER.
Tip
4
If you have tuned in an AM station, adjust
the direction of the AM loop antenna
(aerial) for optimum reception.
1 Press TUNER repeatedly to
If you cannot tune in a station
and the entered numbers flash
Make sure you have entered the right
frequency. If not, repeat steps 2 to 4. If you still
cannot tune in a station, the frequency is not
used in your area.
select the FM or AM band.
2 Tune in the station that you
want to preset using Automatic
Switch the FM reception mode, if
continued
81GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press MEMORY.
1 Press TUNER repeatedly to
select the FM or AM band.
“MEMORY” appears on the display for a
few seconds. Perform steps 4 and 5 before
the display goes out.
2 Press PRESET +/– repeatedly
to select the preset station you
want.
4 Press PRESET +/– to select a
preset number.
Each time you press the button, you can
select a preset station as follows:
• AM band: AM1 to AM30
If “MEMORY” goes out before you select
the preset number, start again from step 3.
• FM band: FM1 to FM30
5 Press ENTER.
You can also press the numeric buttons to
select the preset station you want. Then,
press ENTER to enter the selection.
The station is stored as the selected preset
number.
If “MEMORY” goes out before you press
MEMORY, start again from step 3.
Naming preset stations
6 Repeat steps 1 to 5 to preset
another station.
1
3
Tuning to preset stations
1
5-7
4
2
1 Press TUNER repeatedly to
2
select the FM or AM band.
82GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Tune in the preset station you
want to create an index name
Listening to the XM Radio
XM Radio is the satellite radio service with
millions of listeners across the U.S.
3 Press RECEIVER.
Receiver operation is enabled.
Broadcasting live daily. XM Radio offers 170
digital radio channels offering music, news,
sports, comedy, talk, entertainment, traffic and
weather reports, with high quality digital
sound.
XM $12.95 monthly service subscription sold
separately. XM Connect and Play™ antenna
required to receive XM service (sold
4 Press MENU.
The list of setting menus appears.
5 Press V/v repeatedly to select
“Tuner Settings,” then press
.
separately). Installation costs and other fees
and taxes, including a one-time activation fee
may apply. Subscription fee is consumer only.
All fees and programming subject to change.
Channels with frequent explicit language are
indicated with an XL. Channel blocking is
available for XM radio receivers by calling 1-
800-XMRADIO. Subscriptions subject to
Customer Agreement available at
6 Press V/v repeatedly to select
“NAME IN?.”
7 Press
to enter the
parameter.
The cursor flashes and you can select a
character. Follow the procedure given in
xmradio.com. XM service only available in
the 48 contiguous United States. XM Ready
and XM Connect-and-Play are trademarks of
XM Satellite Radio Inc. ©2006 XM Satellite
Radio Inc. All rights reserved.
Activate XM Service:
Find the 8-character XM Radio ID of the
Connect-and-Play antenna. Record the Radio
ID here for reference: ssssssss. To
check the ID of your antenna, see “Checking
Radio ID does not use the letters I, O, S, or F.)
Activate your XM Satellite Radio service
online at http://activate.xmradio.com or by
calling 1-800-XMRADIO (1-800-967-2346).
You will need a major credit card.
XM will send a signal from the satellites to
activate the full channel lineup. Activation
normally takes 10 to 15 minutes, but during
peak busy periods, you may need to keep your
player on for up to an hour. When you can
access the full channel lineup on your player,
you are done.
continued
83GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Checking the XM Radio ID
• To ensure optimal reception of XM’s satellite
signal, move your antenna to various window
locations around your home to see where the best
reception will be received. Most XM customers
place the antenna in a south-facing window with a
clear view to the sky.
1
• Residents in Canada, please see information about
XM Canada at the following webpage or number:
(http://www.xmradio.ca/)
(1-877-GET-XMSR or 1-877-438-9677)
Connecting the XM Radio
Before operating the system, connect the XM
Connect-and-Play antenna to the XM jack.
XM jack
2
1 Press TUNER repeatedly to
select “XM RADIO.”
2 Press TUNING +/– to select
channel 0.
You can also press TUNING MODE on
the receiver to select “AUTO,” and then
turn TUNING to select channel 0.
3 Check the XM Radio ID on the
display and write it in the space
provided here.
ID:______________________________
84GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving XM Radio broadcasts
Selecting channels from a
category (CATEGORY TUNING)
You can select a channel from one category or
all the categories by changing the category
mode.
1
1
2
3
2
4
1 Press TUNER repeatedly to
select “XM RADIO.”
2 Press TUNING +/– to select a
channel.
You can also press TUNING MODE on
the receiver to select “AUTO,” and then
turn TUNING to select a channel.
1 Press TUNER repeatedly to
select “XM RADIO.”
2 Press CATEGORY MODE
repeatedly to select the “ONE
CATEGORY.”
• ALL CATEGORY: You can select a
channel from all the categories. The
initial setting is “ALL CATEGORY.”
• ONE CATEGORY: You can select a
channel from one category. “CAT” is
displayed on the display when you set to
“ONE CATEGORY” mode.
3 Press CATEGORY +/– to select
the category you want.
The category is selected and the channel
with the lowest number in the specified
category is selected.
continued
85GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press TUNING +/– to select the
Displaying the XM-Radio
information on the display
channel.
You can also press TUNING MODE on
the receiver to select “AUTO,” and then
turn TUNING to select the channel.
Notes
DISPLAY
• When you select a channel in the “ONE
CATEGORY” mode, the channel you selected may
not be the one in the category you want. This is
because one channel may belong to more than one
category.
• If you press CATEGORY +/– in the “ALL
CATEGORY” mode, the first channel of the next or
previous category is selected (CATEGORY SKIP).
Press DISPLAY repeatedly.
Each time you press DISPLAY while tuning in
the channel, the display changes cyclically as
follows:
Channel name t Channel number t
Category t Artist name/Feature t
Song/Program title t Sound field type t
Volume
Selecting channels by inputting
the channel number directly
(DIRECT TUNING)
1
3
2
4
1 Press TUNER repeatedly to
select “XM RADIO.”
2 Press D.TUNING.
3 Press the numeric buttons to
enter the channel number.
4 Press ENTER.
The selected channel is tune in.
86GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press PRESET +/– to select the
preset number.
Presetting XM Radio
stations
You can select the channels you want directly
by presetting them using the preset numbers.
You can preset up to 30 XM Radio channels.
You can also select the number by
pressing the numeric buttons.
Preset numbers from 1 to 30 are available,
and channel 1 is preset for all the preset
numbers when you purchase the receiver.
5 Press ENTER.
Presetting channels using the
preset numbers
6 Repeat steps 2 to 5 to preset
another channel.
Selecting the channel by using
the preset numbers
1
1
Numeric
buttons
3,5
Numeric
buttons
4
1 Press TUNER repeatedly to
2
select “XM RADIO.”
2 Tune in the channel you want to
preset.
1 Press TUNER repeatedly to
For details on selecting channels, see
select “XM RADIO.”
3 Press MEMORY.
continued
87GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press PRESET +/– repeatedly
to select the preset channel you
want.
You can also press the numeric buttons to
select the preset channel you want. Then
press ENTER to enter the selection.
You can select preset stored preset
channels from 1 to 30.
Note
The preset channel information will be updated
depending on the service provided by the XM
Satellite Radio Inc. that you have subscribed to.
XM Radio messages list
Message
appears
Explanation
Remedies
CHECK
ANTENNA
The XM antenna is not connected or
transmission is not being received
properly.
Make sure that the antenna is securely
connected.
Try to disconnect the antenna, then reconnect it,
or turn off the power, then it turn back on.
UPDATING
NO SIGNAL
The encryption code is being updated.
The signal is too weak.
Wait until the encryption code has been updated.
Adjust the antenna so that the signal is as strong
as possible.
LOADING
OFF AIR
The audio channel or information is being Wait until the audio channel or information has
acquired.
been acquired.
The selected channel is off the air.
Make sure that you selected the channel
properly.
Try to select another channel.
(space)––––
There is no characteristic information
such as an artist name, song title or
program title available.
—
XM––
The preset number entered is an invalid Enter a number from 1 to 30.
number.
–––CH
The selected channel is not available.
—
88GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press MENU.
The following menus are displayed on the
TV screen.
Other Operations
1-Level Settings
Displaying menus of the
receiver on the TV screen
Press ON SCREEN, then display a menu on
the TV screen connected to this receiver. You
can set up menus easily.
2-Equalizer Settings
3-Surround Settings
4-Tuner Settings
5-Audio Settings
6-Video Settings
7-Speaker Settings
8-System Settings
9-Auto Calibration
5 Press V/v repeatedly to select
1
3
the menu item, then press
enter the menu.
to
6 Press V/v repeatedly to select
the parameter, then press
enter the parameter.
to
Depending on the parameter, the selected
parameter can be entered by completing
step 7.
7 Press ON SCREEN.
The menu setting display disappears.
2,7
5,6
4
1 Turn on the receiver and the TV.
2 Press ON SCREEN.
Switch the input of the TV so that a
setting menu is displayed on the TV
screen connected to this receiver.
3 Press RECEIVER.
Receiver operation is enabled.
89GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press V/v repeatedly to select
“Tuner Settings,” “Audio
Settings,” “Video Settings,” or
“Auto Calibration.”
Naming inputs
You can enter a name of up to 8 characters for
inputs and display it on the receiver’s display.
This is convenient for labeling the jacks with
the names of the connected components.
5 Press
to enter the menu.
6 Press V/v repeatedly to select
“NAME IN ?” or “A.CAL
NAME?,” then press
enter.
to
The cursor flashes and you can select a
character.
Press V/v to select a character, press B/b
to select the position in which to enter the
selected character.
1
2
To enter a blank space
Press B/b without inputting a character.
You can also turn +/– on the receiver until
a blank space appears on the display.
If you made a mistake
4-7
Press B/b until the character you want to
change flashes, then turn +/– on the
receiver to select the correct character.
3
Tip
You can select the character type by pressing
V/v.
1 Press the input button to select
an input you want to create an
index name for.
Alphabet (upper case) t Alphabet (lower
case) t Numbers t Symbols
7 Press
to enter the name.
You can also use INPUT SELECTOR on
the receiver. The selected input appears
on the display.
The entered name is registered.
To select a component connected to the
HDMI IN1/2 jack, press the HDMI button
repeatedly.
2 Press RECEIVER.
Receiver operation is enabled.
3 Press MENU.
The list of setting menus appears.
90GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press RECEIVER.
Receiver operation is enabled.
Switching between
digital and analog audio
(INPUT MODE)
3 Press INPUT MODE repeatedly
to select the audio input mode.
The selected audio input mode appears on
the display.
When you connect components to both digital
and analog audio input jacks on the receiver,
you can fix the audio input mode to either of
them, or switch from one to the other,
depending on the type of material you intend
to watch.
Audio input modes
• AUTO
Gives priority to digital audio signals when
there are both digital and analog
connections.
If there are no digital audio signals, analog
audio signals are selected.
• COAX
Specifies the digital audio signals input to
the DIGITAL COAXIAL jack.
• OPT
1
Specifies the digital audio signals input to
the DIGITAL OPTICAL jack.
• ANALOG
2
Specifies the analog audio signals input to
the AUDIO IN (L/R) jacks.
Notes
• You cannot select the digital audio input assigned
to another function using the DIGITAL ASSIGN
• Some audio input modes may not be set up
depending on the input.
• When either HDMI input or XM Radio is selected,
“------” appears on the display, and you cannot
select other modes. Select an input mode other than
the HDMI input and XM Radio, then set the audio
input mode.
• When the ANALOG DIRECT function is being
used, or MULTI IN is selected, audio input is set to
“ANALOG.” You cannot select other modes.
3
1 Press the input button.
You can also use INPUT SELECTOR on
the receiver.
91GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press V/v repeatedly to select
“DIGITAL ASSIGN ?,” then
Listening to digital sound
from other inputs
(DIGITAL ASSIGN)
press
.
5 Press V/v repeatedly to select a
vacant digital audio input
(VIDEO 2 OPT in the example).
You can reassign digital audio input that has
OPTICAL or COAXIAL (VIDEO 1 IN, DVD
IN, TV/SAT IN, MD/DAT IN, SA-CD/CD IN)
signals to another input (VIDEO 2 etc.) when
they are not currently being used.
For example, to make the DVD player the
sound source for the digital audio input using
the OPTICAL IN jack on the receiver, then:
• Connect the optical output jack of the DVD
player and the OPTICAL VIDEO 2 IN jack
of the receiver.
6 Press
.
7 Press V/v repeatedly to select
the input (DVD in the example)
you want to assign to the digital
audio input jack selected in
step 5.
8 Press
.
If an input is switched to “DVD,” the
sound of the DVD player will also
become a digital sound through the
OPTICAL VIDEO 2 IN jack.
• Assign “VIDEO 2 OPT” to “DVD” in the
DIGITAL ASSIGN setting.
The input you can assign varies for each
audio input. For details, see the following
1
Assignable inputs for digital
audio input
The initial setting is marked with an
underscore.
3-8
2
Digital audio input Assignable inputs
VIDEO 1 OPT
VIDEO 2 OPT
VIDEO 3 OPT
TV/SAT OPT
MD/DAT OPT
DVD COAX
VIDEO 1, DVD,
TAPE/CD-R, SA-CD/CD
VIDEO 2, DVD,
TAPE/CD-R, SA-CD/CD
VIDEO 3, DVD,
TAPE/CD-R, SA-CD/CD
1 Press RECEIVER.
TV/SAT, DVD,
TAPE/CD-R, SA-CD/CD
Receiver operation is enabled.
2 Press MENU.
MD/DAT, DVD,
TAPE/CD-R, SA-CD/CD
The list of setting menus appears.
DVD, VIDEO 1, VIDEO 2,
VIDEO 3, TV/SAT,
MD/DAT
3 Press V/v repeatedly to select
“Audio Settings,” then press
to enter.
92GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital audio input Assignable inputs
Watching HDMI images
from other inputs
TAPE/CD-R COAX TAPE/CD-R, VIDEO 1,
VIDEO 2, VIDEO 3,
TV/SAT, MD/DAT
SA-CD/CD COAX
SA-CD/CD, VIDEO 1,
VIDEO 2, VIDEO 3,
TV/SAT, MD/DAT
(HDMI VIDEO ASSIGN)
You can reassign an HDMI video input to
another input.
Notes
• You cannot reassign more than one digital audio
input to the same input.
For example, you can watch HDMI images
when you select a SA-CD/CD player, while
listening to a super audio CD via the SA-CD/
CD jack.
• You cannot assign optical signals from an input
source to the optical input jacks on the receiver, and
you cannot assign coaxial signals from the input
source to the coaxial input jacks on the receiver.
• You cannot use the digital audio input as the
original input when it has been reassigned to
another input.
1
• When you assign the digital audio input, the
INPUT MODE setting may change automatically
3-8
2
1 Press RECEIVER.
Receiver operation is enabled.
2 Press MENU.
The list of setting menus appears.
3 Press V/v repeatedly to select
“Video Settings,” then press
.
4 Press V/v repeatedly to select
“HDMI VIDEO ASSIGN ?,” then
press
.
5 Press V/v repeatedly to select
an HDMI input you want to
reassign.
continued
93GB
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Press
7 Press V/v repeatedly to select
the input you want to assign as
an HDMI video input selected in
step 5.
.
Watching component
images from other inputs
(COMPONENT VIDEO ASSIGN)
You can reassign a component video input to
another input (VIDEO 2 IN etc.).
For example, you can watch component
images when you select a SA-CD/CD player,
while listening to a super audio CD via the SA-
CD/CD IN jack.
8 Press
.
The input you can assign varies for each
component video input. For details, see
input.”
Assignable inputs for an HDMI
video input
The initial setting is marked with an
underscore.
1
HDMI video
input
Assignable inputs
HDMI 1
NONE, VIDEO 1, VIDEO 2,
VIDEO 3, DVD, TV/SAT,
TAPE/CD-R, MD/DAT,
SA-CD/CD
3-8
2
HDMI 2
NONE, VIDEO 1, VIDEO 2,
VIDEO 3, DVD, TV/SAT,
TAPE/CD-R, MD/DAT,
SA-CD/CD
Note
You cannot reassign more than one HDMI input to
the same input.
1 Press RECEIVER.
Receiver operation is enabled.
2 Press MENU.
The list of setting menus appears.
3 Press V/v repeatedly to select
“Video Settings,” then press
.
4 Press V/v repeatedly to select
“COMPONENT V. ASSIGN ?,”
then press
.
94GB
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press V/v repeatedly to select
an input (DVD in the example)
you want to reassign.
Changing the display
You can check the sound field, etc., by
changing the information on the display.
6 Press
.
7 Press V/v repeatedly to select
the input (SA-CD/CD in the
example) you want to assign as
the component video input
selected in step 5.
DISPLAY
8 Press
.
If an input is switched to “SA-CD/CD,”
the image from the DVD player will be a
component image.
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display
will change as follows.
Station name t Frequency t Sound field
type t Volume…
The input you can assign varies for each
component video input. For details, see
the following “Assignable inputs for
FM and AM band
Assignable inputs for
component video input
The initial setting is marked with an
underscore.
Preset station name and sound field type* y
Frequency and sound field type
* Index name appears only when you have assigned
Index name does not appear when only blank
spaces have been entered, or it is the same as the
input name.
Component
video input
Assignable inputs
VIDEO1
NONE, VIDEO 1, VIDEO 2,
VIDEO 3, TAPE/CD-R,
MD/DAT, SA-CD/CD
DVD
NONE, VIDEO 2, VIDEO 3,
DVD, TAPE/CD-R, MD/DAT,
SA-CD/CD
TV/SAT
NONE, VIDEO 2, VIDEO 3,
TV/SAT, TAPE/CD-R, MD/DAT,
SA-CD/CD
Notes
• You cannot reassign more than one component
video input to the same input.
• You cannot use the component video input as the
original input when it has been reassigned to
another input.
95GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
You can set the receiver to turn off
automatically at a specified time.
Recording using the
receiver
You can record from a video/audio component
using the receiver. Refer to the operating
instructions supplied with your recording
component.
SLEEP
1
Press SLEEP repeatedly.
Each time you press SLEEP, the display
changes cyclically as follows:
Recording onto a MiniDisc or
audio tape
You can record onto a MiniDisc or audio tape
using the receiver. See the operating
instructions supplied with your MD deck or
tape deck.
When Sleep Timer is being used, “SLEEP”
lights up on the display.
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time appears
on the display. If you press SLEEP again, the sleep
timer will be changed.
1 Press the input button of the
playback component.
You can also use INPUT SELECTOR on
the receiver.
2 Prepare the playback
component for playing.
For example, insert a CD into the CD
player.
3 Prepare the recording
component.
Insert a blank MD or tape into the
recording deck and adjust the recording
level.
4 Start recording on the
recording deck, then start
playback on the playback
component.
96GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Sound adjustments do not affect the signal output
from the TAPE/CD-R OUT or MD/DAT OUT
jacks.
• The audio signals input to the MULTI CHANNEL
INPUT jacks are output only from the front left/
right channels.
To record digital sound
Connect a component for playback to the
digital audio input (OPTICAL IN) jack, and
connect the recording component to the
OPTICAL MD/DAT OUT jack.
Recording onto recording media
1 Press the input button of the
playback component.
You can also use INPUT SELECTOR on
the receiver.
2 Prepare the component for
playing.
For example, insert the video tape you
want to copy into the VCR.
3 Prepare the recording
component.
Insert a blank video tape, etc. into the
recording component (VIDEO 1 or
VIDEO 2) for recording.
4 Start recording on the
recording component, then
start playback on the playback
component.
Notes
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to
record from the sources.
• The audio signals input to the MULTI CHANNEL
INPUT jacks are output only from the front left/
right channels.
97GB
Download from Www.Somanuals.com. All Manuals Search And Download.
When using an IR repeater (not supplied), you
can also operate both a component in the main
zone and a Sony receiver in zone 2 from zone
2. Use the RM-AAL003 remote for the
operation.
Listening to the sound in
another zone (Zone 2
operations)
• Switching the output source for the ZONE 2
OUT jacks.
• Switching the Sony receiver’s power on or
off in zone 2.
• Adjusting the volume of the Sony receiver in
zone 2.
You can enjoy images and sounds from a
component connected to the receiver in a zone
(zone 2) other than the main zone. For
example, you can listen to the CD in the main
zone and watch the DVD in zone 2.
Multi connections
1 Outputs sound from speakers in zone 2 using the SURROUND BACK
SPEAKERS terminals of the receiver.
Main zone
Zone 2
STR-DG1000
A
B
TV
monitor
C
D
D
ZONE 2 VIDEO OUT
RM-AAL003
SURROUND BACK
SPEAKERS
AAudio component
BVideo component
CIR repeater (not supplied)
DSpeaker
98GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Outputs sound from speakers in zone 2 using the receiver and another
amplifier.
Main zone
Zone 2
STR-DG1000
TV
monitor
A
B
E
E
C
D
C
ZONE 2 VIDEO OUT
ZONE 2 AUDIO OUT
RM-AAL003
AAudio component
BVideo component
CIR repeater (not supplied)
DSony’s Amplifier/Receiver
ESpeaker
Notes
• Connect video signals to the component of zone 2
using the VIDEO jack.
• Connect audio signals to the component of zone 2
using the AUDIO L/R jack.
Tips
• Only signals from components connected to the
analog input jacks are output through the ZONE 2
jack. No signal is output from components
connected to only the digital input jacks.
• When “SOURCE” is selected, the signals input to
the MULTI CHANNEL INPUT jacks are not
output from the ZONE 2 jack even when the
MULTI IN is selected in the main zone. The 2
channel analog audio signals of the current input
are output.
continued
99GB
Download from Www.Somanuals.com. All Manuals Search And Download.
The following operations are described for
connecting an IR repeater and operating the
receiver in zone 2. When an IR repeater is not
connected, use this receiver in the main zone.
4 Press one of the input buttons
on the remote to select the
source signals you want to
output.
For zone 2, analog video and audio
signals are output. When you select
“SOURCE,” the signals of the current
input selected in the main zone are output.
4
2
5 Adjust to a suitable volume.
you can only adjust the surround back
speaker volume in zone 2.
1 Set “SUR BACK SP” to “ZONE 2” in
2 Adjust the volume using MASTER
VOL+/– on the remote.
adjust the volume using the receiver of
zone 2.
Tips
• Even when this receiver is turned off, the receiver
in zone 2 remains turned on. To turn off all
receivers, press ?/1 and AV ?/1 on the RM-
AAL003 remote at the same time (SYSTEM
STANDBY).
• Only signals from components connected to the
analog input jacks are output through the ZONE 2
jacks. No signals are output from components
connected to only the digital input jacks.
• When “SOURCE” is selected, the signals input to
the MULTI CHANNEL INPUT jacks are not
output from the ZONE 2 OUT jacks even when
MULTI IN is selected. The analog audio signals of
the current function are output.
• When “TUNER” is selected, the same type of radio
station (FM/AM/XM) selected in the main zone is
selected in zone 2. When the receiver in the main
zone is turned off, or an input source other than
“TUNER” is selected, you can select a broadcast
from FM/AM/XM in zone 2.
5
1 Turn on the main receiver (this
receiver).
The remote switches to zone 2 mode.
2 Press ZONE 2.
3 Turn on the amplifier in zone 2 if
it is used in zone 2.
100GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To operate the receiver using an
IR repeater
You can operate the receiver without pointing
the remote toward the IR sensor of the receiver
if you use an IR repeater.
Using a bi-amplifier
connection
If you are not using surround back speakers,
you can use the SURROUND BACK
SPEAKERS terminals for the front speakers
for use with a bi-amplifier connection.
Use an IR repeater when you install the
receiver in a place where signals from the
remote cannot reach.
STR-DG1000
IR repeater
To connect speakers
(not supplied)
Frontspeaker
(R)
Frontspeaker
(L)
Hi
Hi
RM-AAL003
Lo
Lo
Connect the terminals on the Lo (or Hi) side of
the front speakers to the FRONT SPEAKERS
A terminals, and connect the terminals on the
Hi (or Lo) side of the front speakers to the
SURROUND BACK SPEAKERS terminals.
Make sure that metal fittings of Hi/Lo attached
to the speakers have been removed from the
speakers. Not doing so may cause a
malfunction of the receiver.
To set up speakers
Set “SUR BACK SP” to “BI-AMP” in the
signals output from the FRONT SPEAKERS
A terminals can be output from the
SURROUND BACK SPEAKERS terminals.
continued
101GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• You cannot use the FRONT SPEAKERS B
terminals for a bi-amplifier connection.
• When you use the auto calibration function, make
the bi-amplifier settings before you perform auto
calibration.
• If you make the bi-amplifier settings, the speaker
level, balance, and equalizer settings of the
surround back speakers become invalid, and those
of the front speakers are used.
• Signals output from the PRE OUT jacks are used
with the same settings as those of the SPEAKERS
terminals.
102GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote
Operating each component using the remote
When you program the remote to control the
following Sony or non-Sony components, you
can use the buttons on the remote that are
marked with circles. Note, however, that some
buttons may not operate your component.
If you want to change the contents of the input
list to match your particular components, see
Table of buttons used to control each component
TV VCR DVD Blu-ray PSX Video CD Digital
Digital DSS, Tape deck DAT CD Tuner Receiver
Component
player, Disk
DVD/VHS player
combo
player, LD CATV satellite/ BST
A/B
deck player,
MD
player terminal terrestrial
(US)
receiver
(EURO)
deck
Button
AV
?
/1,
z
z
z
z
z
z
z
z
z
z
z
z
?
/1
(after pressing TV)
Numeric buttons
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
MEMORY, ENTER
z*
CLEAR, D.TUNING,
>10, –/– –
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
DISPLAY
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
OPTIONS/TOOLS
RETURN/EXIT
z
z
z
z
z
z
z
z
z
z
z
z
z
z**
z
V
/v/
B/b
,
z
z
z
z
z
MENU
z
.
/
>
z***
z
z
CATEGORY +/– /
REPLAY/
z
z
ADVANCE,
, TUNING +/–
CATEGORY MODE,
B·/·b
m
/
M
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
H,
X,
x
DISK SKIP
MUTING, MASTER
VOL +/–, TV VOL +/–
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
PRESET +/–,
TV CH +/–
z
z
z
z
z*
DVD TOP MENU/
NIGHT MODE, DVD
MENU/INPUT MODE
F1, MACRO1, TV/VIDEO
z
z
z
z
z
z
z**
z
z
F2, MACRO2, WIDE
*
LD player only. ** DSS only. *** Deck B only.
103GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Press AV ?/1 while pressing RM
SET UP.
Programming the remote
The RM SET UP button flashes.
You can customize the remote to match the
components connected to your receiver. You
can even program the remote to control non-
Sony components and also Sony components
that the remote is normally unable to control.
The procedure below uses as an example a
case in which the other manufacturer’s VCR is
connected to the VIDEO 2 jacks on the
receiver.
2 While the RM SET UP button is
flashing, press the input button
(including TV) for the
component you want to control.
For example, if you are going to control a
CD player, press SA-CD/CD.
The RM SET UP button and input button
flash.
Before you begin, note that:
– You cannot change the settings of PHONO.
– The remote can control only components
that accept infrared wireless control signals.
3 Press the numeric buttons to
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control.
Be sure to turn on the receiver and
point the remote towards the
receiver when performing the
following procedure.
The RM SET UP button and input button
light up.
1
2
Note
For a TV remote code value, only numbers in
the 500’s are valid.
4 Press ENTER.
Once the numeric code has been verified,
the RM SET UP button flashes twice and
the remote automatically exits the
programming mode. The input button
also turns off.
3
To cancel programming
4
Press RM SET UP during any step.
104GB
Download from Www.Somanuals.com. All Manuals Search And Download.
The numeric codes
To control a DAT deck
corresponding to the
Maker
Code(s)
203
component and the maker of
the component
SONY
PIONEER
219
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than
one numeric code may be assigned to a
component. If you fail to program your remote
using one of the codes, try using other codes.
To control an MD deck
Maker
Code(s)
301
SONY
DENON
JVC
302
303
KENWOOD
304
Notes
To control a tape deck
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
• All of the input buttons on this remote may not be
available when used with your particular
component.
Maker
Code(s)
201, 202
204, 205
206, 207, 208, 209
210
SONY
DENON
KENWOOD
NAKAMICHI
PANASONIC
PHILIPS
216
To control a CD player
Maker
211, 212
213, 214
215, 216
217, 218
PIONEER
TECHNICS
YAMAHA
Code(s)
101, 102, 103
104, 123
105, 106, 107
108, 109, 110
111, 116
116
SONY
DENON
JVC
To control an LD player
KENWOOD
MAGNAVOX
MARANTZ
ONKYO
Maker
Code(s)
601, 602, 603
606
SONY
112, 113, 114
115
PIONEER
PANASONIC
PHILIPS
116
To control a video CD player
PIONEER
TECHNICS
YAMAHA
117
Maker
Code(s)
115, 118, 119
120, 121, 122
SONY
605
continued
105GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To control a VCR
To control a DVD recorder
Maker
Code(s)
Maker
Code(s)
SONY
701, 702, 703, 704,
705, 706
SONY
403
AIWA*
710, 750, 757, 758
707, 708, 709, 759
740
To control a TV
Maker
AKAI
Code(s)
BLAUPUNKT
EMERSON
SONY
501, 502
711, 712, 713, 714,
715, 716, 750
DAEWOO
504, 505, 506, 507,
515, 544
FISHER
717, 718, 719, 720
FISHER
508
GENERAL ELECTRIC 721, 722, 730
GOLDSTAR/LG
503, 511, 512, 515,
534, 544
GOLDSTAR/LG
GRUNDIG
HITACHI
723, 753
724
GRUNDIG
HITACHI
517, 534
722, 725, 729, 741
717
513, 514, 515, 544
521, 522
ITT/NOKIA
JVC
ITT/NOKIA
JVC
726, 727, 728, 736
730, 731, 738
732, 733, 734, 735
736
516
MAGNAVOX
MITSUBISHI/MGA
NEC
MAGNAVOX
MITSUBISHI/MGA
NEC
503, 518, 544
503, 519, 544
503, 520, 544
509, 524
PANASONIC
729, 730, 737, 738,
739, 740
PANASONIC
PHILIPS
515, 518
PHILIPS
729, 730, 731
729
PIONEER
509, 525, 526, 540
PIONEER
RCA/PROSCAN
510, 527, 528, 529,
544
RCA/PROSCAN
722, 729, 730, 731,
741, 747
SAMSUNG
503, 515, 531, 532,
533, 534, 544
SAMSUNG
SANYO
742, 743, 744, 745
717, 720, 746
748, 749
SANYO
508, 545, 546, 547
535
SHARP
SHARP
TELEFUNKEN
TOSHIBA
ZENITH
751, 752
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
523, 536, 537, 538
530, 537, 539
535, 540, 541
542, 543
747, 755, 756
754
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
To control a DVD player
Maker
Code(s)
401, 402, 403
406, 408
407
SONY
PANASONIC
PHILIPS
PIONEER
TOSHIBA
DENON
409
404
405
106GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To control a satellite tuner or
cable box
Performing several
commands in sequence
automatically
Maker
Code(s)
SONY
801, 802, 803, 804
JERROLD/G.I.
806, 807, 808, 809,
810, 811, 812, 813,
814
(Macro Play)
PANASONIC
RCA
818
The Macro Play function lets you link several
commands in a sequential order as a single
command.
805, 819
815, 816, 817
S. ATLANTA
The remote provides 2 macro lists (MACRO 1
and MACRO 2). You can specify up to 20
commands for each macro list.
To control a tuner
Maker
Code(s)
SONY
002, 003, 004, 005
Note
When setting up Macro Play, replace the batteries
with new ones.
To control a hard disc recorder
Maker
Code(s)
SONY
307, 308, 309
To control a blu-ray disc player
Maker
Code(s)
SONY
310, 311, 312
To control a PSX
Maker
Code(s)
SONY
313, 314, 315
continued
107GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press the button for the
operation you want to perform
to learn the function as follows.
Program the sequence of the
operation
Press
Operations to be
programmed
1,5
2,3
H, x, X,
M, m,
., >
Performs the operation
of the button.
The input
Switches inputs.
button for more
than 1 second
MACRO 1 or Make a one second
MACRO 2
interval. When you want
to make a longer
interval, press MACRO
1 or MACRO 2
repeatedly.
The input button selected in step 2 flashes
twice, then lights up again.
4 Repeat steps 2 and 3. When you
want to assign another
command for the same
component, repeat step 3.
3
5 Press RM SET UP to finish the
programming process.
Tip
If the RM SET UP button flashes five times in step
1, and the macro programming process does not
start, replace the batteries with new ones.
1,3
1 Press MACRO 1 or MACRO 2 for
more than 1 second while
pressing RM SET UP.
To cancel programming
Press RM SET UP. Also, not pressing any
button for 60 seconds cancels the settings.
The previous command remainds valid.
The RM SET UP button flashes twice.
2 Press the input button of the
component that you want to
assign one of the following
operations.
The selected input button lights up.
108GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting macro play
Setting remote control
codes that are not stored
in the commander
Even if a remote control code is not one of the
presets stored in the remote, it is possible for
the remote to learn the code using the Learning
function.
1 Press RECEIVER.
The RECEIVER button lights up, and then
turns off.
2 Press MACRO 1 or MACRO 2 to start
the macro.
The macro starts and execute the
commands in the order you assigned them.
While the commands are being sent, the
RM SET UP button flashes and the
RECEIVER button lights up. When the
commands have been sent, the RM SET UP
and RECEIVER buttons turn off.
Note
When setting up the receiver to learn the remote
command modes, replace the batteries with new
ones.
To erase a programmed macro
1,6
1
1 Press MACRO 1 or MACRO 2 for more
than 1 second while pressing RM SET
UP to clear the stored macro.
The RM SET UP button flashes twice,
repeatedly.
2
2 Press RM SET UP.
Settings stored as macro are cleared.
Example for assigning button 1 to VIDEO 1
of the remote:
1 Press TV while pressing RM
SET UP.
The RM SET UP button lights up.
2 Press the input button (VIDEO 1
in the example) for which you
want to use the Learning input
function.
The input button flashes. (The RM SET
UP button remains lit.)
3 Press the button (button 1 in
the example) you want to use as
the VIDEO 1 button.
The input button you selected in step 2
lights up. (The RM SET UP button
remains lit.)
continued
109GB
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Point the remote code receiver
section of the remote toward
the receiver/transmitter on the
remote control to be learned
from.
Using a command that has been
learned
When selecting a learned input, press the
button used to learn that function.
While the second remote is receiving the
signal, the input button selected in step 2
turns off.
To erase the learned code
1 Press TV while pressing RM SET UP.
2 Press the input button (VIDEO 1 in the
example) for which you want to clear
the setting.
About 5 cm - 10 cm (2" - 4")
The input button flashes. (The RM SET UP
button remains lit.)
5 The RM SET UP button flashes
twice, then the learning
3 Press ?/1 for more than 1 second.
The input button flashes twice, repeatedly.
process is completed.
4 Press the input button to clear the
stored setting.
When the learning process fails, the RM
SET UP button flashes five times. Try to
perform process again from step 2.
The RM SET UP button flashes twice, then
the clearing process is completed.
When the clearing process fails, the RM
SET UP button flashes five times. Try to
perform process again from step 2.
6 Press RM SET UP to finish the
Learning function process.
Tips
• When the memory capacity for storing remote
control codes reaches a certain limit, the RM SET
UP button flashes 10 times, and then the learning
process ends.
• If the RM SET UP button flashes five times in step
1, and the learning process does not start, replace
the batteries with new ones.
To cancel learning
Press RM SET UP. Also, not pressing any
button for 60 seconds cancels the settings.
110GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing all the contents
of the remote’s memory
1
1,2
1 Press and hold MASTER VOL –
first, then press ?/1 and then
AV ?/1.
The RM SET UP button flashes three
times.
2 Release MASTER VOL –.
All the contents of the remote’s memory
(i.e., all the programmed data) are
cleared.
111GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x Crossover frequency
The frequency at which two speaker’s
frequencies intersect.
Additional Information
x Digital Cinema Sound (DCS)
Unique sound reproduction technology for
home theater developed by Sony, in
cooperation with Sony PicturesEntertainment,
for enjoying the exciting and powerful sound
of movie theaters at home. With this “Digital
Cinema Sound” developed by integrating a
DSP (Digital signal processor) and measured
data, the ideal sound field intended by
Glossary
x Cinema Studio EX
A surround sound mode that can be regarded
as the compilation of Digital Cinema Sound
technology, delivers the sound of a dubbing
theater using three technologies: “Virtual
Multi Dimensions,” “Screen Depth Matching,”
and “Cinema Studio Reverberation.”
filmmakers can be experienced at home.
“Virtual Multi Dimensions,” the virtual
speaker technology, creates a virtual multi-
surround environment with actual speakers up
to 7.1channels, and brings the surround sound
experience of a theater with the latest facilities
into your home.
“Screen Depth Matching” reproduces treble
attenuation, fullness, and depth of sound
usually created in a theater using sound
emission from behind the screen. This is then
added to the front and center channels.
“Cinema Studio Reverberation” reproduces
the sound characteristics of state-of-the-art
dubbing theaters and recording studios,
including Sony Pictures Entertainment’s
dubbing studios. There are three modes, A/B/
C, available according to the studio type.
x Dolby Digital
Digital audio encoding/decoding technology
developed by Dolby Laboratories, Inc. It
consists of front (left/right), center, surround
(left/right) and sub woofer channels. It is a
designated audio standard for DVD-video and
also known as 5.1channels surround.
x Dolby Digital Surround EX
Acoustic technology developed by Dolby
Laboratories, Inc. Surround back information
is matrixed into regular left and right surround
channels so that the sound can be reproduced
in 6.1channels. Active scenes, especially, are
recreated with a more dynamic and realistic
sound field.
x Component video
x Dolby Pro Logic II
A format for transmitting video signal
information consisting of three separate
signals: luminance Y, chrominance Pb, and
chrominance Pr. High quality pictures, such as
DVD video or HDTV pictures, are transmitted
more faithfully. The three jacks are color-
coded green, blue, and red.
This technology converts 2 channel stereo
recorded audio into 5.1 channels for playback.
There is a MOVIE mode for movies and
MUSIC mode for stereo sources such as
music. Old movies encoded in the traditional
stereo format can be enhanced with 5.1
channels surround sound. The GAME mode is
suitable for video games.
x Composite video
A standard format for transmitting video
signal information. The luminance signal Y
and chrominance signal C are combined and
transmitted together.
112GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x Dolby Pro Logic IIx
x DTS-ES
Technology for 7.1 channels (or 6.1 channels)
playback. Along with audio encoded in Dolby
Digital Surround EX, 5.1 channels Dolby
Digital encoded audio can be reproduced in
7.1 channels (or 6.1 channels). Furthermore,
existing stereo recorded content can also be
reproduced in 7.1 channels (or 6.1 channels).
Format for 6.1 channels playback with
surround back information. There are two
modes, “Discrete 6.1” which records all
channels independently, and “Matrix 6.1”
which matrixes surround back channel into
surround left and surround right channels. It is
ideal for playback of motion picture
soundtracks.
x Dolby Surround (Dolby Pro
Logic)
x Dynamic Range
Audio processing technology developed by
Dolby Laboratories, Inc. Center and mono
surround information is matrixed into two
stereo channels. When reproduced, audio is
decoded and output in 4 channels surround
sound. This is the most common audio
processing method for DVD-video.
The reproductive capacity of audio signals.
The difference between the minimum
(quietest) and the maximum (loudest) sound
that can be reproduced is expressed by a
number value of dB. A larger number value
means a greater degree of quietness or
loudness can be reproduced.
x Downmix
x HDMI (High-Definition
A method to output multi-channel audio such
as 5.1 channels, encoded into two channels.
Multimedia Interface)
HDMI is an interface that supports both video
and audio on a single digital connection. The
HDMI connection carries standard to high
definition video signals and multi-channel
audio signals to audio/video components, such
as HDMI equipped TVs, in digital form
without degradation. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding
x DTS 96/24
A high sound quality digital signal format. It
records audio at a sampling frequency and bit
rate of 96kHz/24bit which is the highest
possible for DVD-video. The number of
playback channels varies depending on the
software.
x DTS Neo:6
technology for digital video signals.
This technology converts 2 channels stereo
recorded audio for 6.1 channels playback.
There are two modes to select according to the
playback source or your preference, CINEMA
for movies, and MUSIC for stereo sources
such as music.
x Interlace
A scanning method which completes a picture
by displaying half of the lines on a tube surface
of a TV or monitor each 1/60 second. First, all
the odd-numbered lines are drawn, leaving
spaces between each line, then all the even-
numbered lines are drawn to fill the spaces.
x DTS Digital Surround
Digital audio encoding/decoding technology
for theaters developed by Digital Theater
Systems, Inc. It compresses audio less than
Dolby Digital, delivering a higher quality
sound reproduction.
x L.F.E. (Low Frequency Effects)
Sound effects of low frequencies which are
output from a sub woofer in Dolby Digital or
DTS, etc. By adding a deep bass with a
frequency between 20 to 120 Hz, audio
becomes more powerful.
continued
113GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x PCM (Pulse Code Modulation)
A method of converting analog audio to digital
audio for easy enjoyment of digital sound.
Precautions
x Progressive
On safety
A scanning method that draws all scanning
lines sequentially, as opposed to interlaced
scanning where all the odd and then all the
even lines are drawn.
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
x Sampling frequency
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
To convert analog audio to digital, analog data
should be quantified. This process is called
sampling, and the number of times per second
the analog data is quantified is called the
sampling frequency. A standard music CD
stores data quantified at 44,100 times per
second, which is expressed as a sampling
frequency of 44.1 kHz. Generally speaking, a
higher sampling frequency means better sound
quality.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
• One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
x S video signal
A format for transmitting video signal
information. S video uses a single cable and
two channels, one for the Luminance signal Y
and another for the chrominance signal C.
Better picture quality for recording and
playback than that of Composite signal is
achieved.
• The AC power cord (mains lead) must be
changed only at a qualified service shop.
x TSP (Time Stretched Pulse)
A TSP signal is a highly precise measuring
signal that utilizes impulse energy, measuring
a wide band, from low to high, in a short
period.
The amount of energy used to measure signals
is important to ensure measurement accuracy
in a normal indoor environment. Using TSP
signals makes it possible to measure signals
effectively.
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
114GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
• Do not place the receiver near equipment
such as a television, VCR, or tape deck. (If
the receiver is being used in combination
with a television, VCR, or tape deck, and is
placed too close to that equipment, noise
may result, and picture quality may suffer.
This is especially likely when using an
indoor antenna (aerial). Therefore, we
recommend using an outdoor antenna
(aerial).
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
Audio
There is no sound, no matter which
component is selected, or only a very
low-level sound is heard.
• Check that the speakers and components
are connected securely.
• Check that all speaker cords are connected
correctly.
• Check that both the receiver and all
components are turned on.
On operation
Before connecting other components, be sure
to turn off and unplug the receiver.
• Check that MASTER VOLUME control is
not set at –∞ dB.
• Check that SPEAKERS (OFF/A/B/A+B)
• Press MUTING on the remote to cancel
the muting function.
• Check that you have selected the correct
component with INPUT SELECTOR.
• Check that headphones are not connected.
• When only a very low-level sound is
heard, check to see if NIGHT MODE is
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is no sound from a specific
component.
• Check that the component is connected
correctly to the audio input jacks for that
component.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
component.
continued
115GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Check that the DIGITAL ASSIGN
function is not used to reassign the audio
input of another source to the selected
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
• Make sure you have connected both the L
or R jack to an analog component and not
just to either the L or R jack. Use a
The source sound input from the HDMI
jack is not output from an amplifier or
the TV speaker connected to the
receiver.
• Check that the component is connected
correctly to the HDMI jack for that
component.
• The sound is not output when you display
the receiver’s menu on the TV monitor.
Press ON SCREEN to turn off the display.
• You cannot listen to the Super Audio CD
by connecting HDMI.
• Depending on the playback component,
component may need to be set up. Refer to
the operating instructions supplied with
the each component.
monaural-stereo cable (not supplied).
However, there will be no sound from the
center speaker when a sound field (PRO
LOGIC, etc.) is selected. When the center
speaker is set to “NO,” sound is output
only from the front left/right speakers.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the balance parameters using the
Level Settings menu.
There is no sound from analog 2
channel sources.
• Check that the INPUT MODE is not set to
“COAX” nor “OPT” for the selected input
• Check that the MULTI IN is not selected.
• Check that the DIGITAL ASSIGN
function is not used to reassign the audio
input of another source to the selected
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least 3
m (10 feet) away from a TV set or
fluorescent light.
• Move your TV away from the audio
components.
• Make sure you have grounded the U
SIGNAL GND terminal (only when a
turntable is connected).
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
There is no sound from digital sources
(from COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
INPUT MODE is not set to “COAX” for
the sources from the OPTICAL input jack,
nor set to “OPT” for the sources from the
COAXIAL input jack.
• Check that the MULTI IN is not selected.
• Check that the ANALOG DIRECT
function is not being used.
116GB
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound, or only a very low-
level sound is heard from the center/
surround/surround back speakers.
Recording cannot be carried out.
• Check that the components are connected
• Select a CINEMA STUDIO EX mode
• Select the source component using INPUT
• Make sure the center/surround speaker (s)
is (are) set to either “SMALL” or
• Make sure the surround back speakers are
set to “DUAL” or “SINGLE” (page 67).
The MULTI CHANNEL DECODING lamp
does not light up in blue.
• Check that the playback component is
connected on a digital jack and the input is
selected properly on this receiver.
• Check whether the input source of the
software being played back corresponds to
the multi-channel format.
• Check whether the setup on the playback
component is set to multi-channel sound.
• Check whether the digital audio output of
selected input is not assigned to another
component input using DIGITAL
There is no sound from the surround
back speakers.
• Some discs have no Dolby Digital
Surround EX flag even though the
packages have Dolby Digital Surround EX
logos. In this case, select “ON” in the “SB
There is no sound from the sub woofer.
• Check that the sub woofer is connected
correctly and securely.
Video
• Make sure you have turned on your
speaker.
• When all speakers are set to “LARGE”
and “Neo:6 Cinema,” or “Neo:6 Music” is
selected, there is no sound from the sub
woofer.
There is no picture or an unclear
picture appears on the TV screen or
monitor.
• Select the appropriate input on the receiver
• Set your TV to the appropriate input mode.
• Move your TV away from the audio
components.
• Assign the component video input
correctly.
The surround effect cannot be
obtained.
• Make sure the sound field function is on
(press MOVIE or MUSIC).
• Sound fields do not function for signals
with a sampling frequency of more than 48
kHz.
• The input signal should be same as input
when you are up-converting an input
Dolby Digital or DTS multi-channel
sound is not reproduced.
• Check that the DVD, etc. you are playing
is recorded in Dolby Digital or DTS
format.
• When connecting the DVD player, etc., to
the digital input jacks of this receiver,
make sure the setting for the digital audio
output of the connected component is
available.
continued
117GB
Download from Www.Somanuals.com. All Manuals Search And Download.
The image of the COMPONENT VIDEO
OUT is corrupted.
Outdoor FM antenna (aerial)
Receiver
• When the signals are output from the
COMPONENT VIDEO OUT jack, input
signals other than 480p are corrupted if
“PROGRESSIVE OUT” is set to “ON.”
Set “PROGRESSIVE OUT” to “OFF.”
• Video input signals other than 480p
component are not received when signals
are output from the S VIDEO jack or the
VIDEO jack. Input 480i component video
signals.
To ground
• When component input signals other than
480p are output, use the COMPONENT
VIDEO OUT jack and set
Ground (earth) wire (not supplied)
“PROGRESSIVE OUT” to “OFF.”
Radio stations cannot be tuned in.
• Check that the antennas (aerials) are
connected securely. Adjust the antennas
(aerials) and connect an external antenna
(aerial), if necessary.
The source image input from the HDMI
jack is not output from the receiver or
the TV speaker connected to the
receiver.
• Make sure that cables are correctly and
securely connected to components.
• Depending on the playback component,
component may need to be set up. Refer to
the operating instructions supplied with
the each component.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning). Use direct tuning.
• Make sure you set the tuning interval
correctly (when tuning in AM stations
with direct tuning).
• No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations). Preset the
• Press DISPLAY so that the frequency
appears on the display.
Recording cannot be carried out.
• Check that the components are connected
• Select the source component using INPUT
Tuner
Remote control
The FM reception is poor.
The remote does not function.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antenna (aerial) as shown below. If you
connect the receiver to an outdoor antenna
(aerial), ground it against lightning. To
prevent a gas explosion, do not connect the
ground (earth) wire to a gas pipe.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure that the command modes of the
receiver and the remote are the same. If the
command mode of the receiver and the
remote are different, you cannot operate
118GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Make sure you select the correct input on
the remote.
• When you operate a programmed non-
Sony component, the remote may not
function properly depending on the model
and the maker of the component.
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 110 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Error message
If there is a malfunction, the display shows
a code of two numbers and a message. You
can check the condition of the system by the
message. Refer to the following table to
solve the problem. If any problem persists,
consult your nearest Sony dealer.
Amplifier section
POWER OUTPUT
1) 2)
Rated Power Output at Stereo Mode
PROTECTOR
(8 ohms 20 Hz – 20 kHz,
THD 0.09%):
Irregular current is being output from the
speakers, or the upper panel of the receiver
is covered with something. The receiver will
automatically turn off after a few seconds.
Check the speaker connection and turn on
the power again.
110 W + 110 W
2)
Reference Power Output at Stereo Mode
(4 ohms 20 Hz – 20 kHz,
THD 0.15%):
110 W + 110 W
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
2)
Reference sections for clearing
the memory
FRONT :
120 W + 120 W
2)
CENTER :
120 W SURROUND :
2)
To clear
See
120 W + 120 W
SURROUND BACK :
120 W + 120 W
All memorized settings
Customized sound fields
page 37
page 79
2)
Reference Power Output
(4 ohms 1 kHz, THD 0.7%)
2)
FRONT :
120 W + 120 W
2)
CENTER :
120 W SURROUND :
2)
120 W + 120 W
SURROUND BACK :
2)
120 W + 120 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
Measured under the following conditions:
2)
Power requirements: 120 V AC, 60 Hz
continued
119GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequency response
FM tuner section
Tuning range
87.5 - 108.0 MHz
FM wire antenna (aerial)
PHONO
RIAA equalization curve
Antenna (aerial)
0.5 dB
Antenna (aerial) terminals
75 ohms, unbalanced
MULTI CHANNEL
INPUT, SA-CD/CD,
TAPE/CD-R,
MD/DAT, DVD,
VIDEO 1/2/3
10 Hz – 100 kHz
3 dB
Sensitivity
Mono:
18.3 dBf, 2.2 µV/75 ohms
38.3 dBf, 22.5 µV/75 ohms
Stereo:
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono:
Stereo:
Inputs (Analog)
PHONO
76 dB
70 dB
Sensitivity: 2.5 mV
Impedance: 50 kohms
S/N: 86 dB (A, 20 kHz
LPF)
Harmonic distortion at 1 kHz
Mono:
Stereo:
0.3%
MULTI CHANNEL
INPUT, SA-CD/CD,
TAPE/CD-R, MD/DAT, S/N: 96 dB (A, 20 kHz
Sensitivity: 150 mV
Impedance: 50 kohms
0.5%
Separation
45 dB at 1 kHz
DVD, TV/SAT,
VIDEO1/2/3
LPF)
Frequency response 30 Hz – 15 kHz, +0.5/–2
dB
Selectivity
60 dB at 400 kHz
Inputs (Digital)
AM tuner section
DVD, TAPE/CD-R, SA- Impedance: 75 ohms
3)
Tuning range
530 – 1,710 kHz
CD/CD (Coaxial)
S/N: 96 dB (A, 20 kHz
LPF)
(With 10-kHz tuning scale)
3)
531 – 1,710 kHz
VIDEO 1/2/3, TV/SAT, S/N: 96 dB
(With 9-kHz tuning scale)
MD/DAT (Optical)
(A, 20 kHz LPF)
Antenna (aerial)
Usable sensitivity
Loop antenna (aerial)
50 dB µ/m (at 1,000 kHz or
999 kHz)
Outputs
S/N
54 dB (at 50 mV/m)
TAPE/CD-R, MD/DAT,
Voltage:150 mV
VIDEO1/2 (AUDIO OUT) Impedance: 1 kohms
Harmonic distortion 0.5% (50 mV/m, 400 Hz)
Selectivity
at 9 kHz : 35 dB
at 10 kHz : 40 dB
FRONT L/R, CENTER,
SURROUND L/R,
Voltage: 2 V
Impedance: 1 kohms
SURROUND BACK L/R,
SUB WOOFER
3)
You can change the AM tuning scale to either 9
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
EQUALIZER
Gain levels
10 dB, 1 dB step
120GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
S video:
Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P /C : 0.7 Vp-p, 75 ohms
B
B
P /C : 0.7 Vp-p, 75 ohms
R
R
80 MHz HD Pass Through
(When “PROGRESSIVE
OUT” is set to “OFF”.)
General
Power requirements 120 V AC, 60 Hz
Power consumption 480 W/580 VA
Power consumption (during standby mode)
1 W
AC outlets
2 switched, 100 W/0.8 A
MAX
Dimensions
430 × 175 × 430 mm
(17 × 7 × 17 in)
including projecting parts
and controls
Mass (Approx.)
15.5 kg (34 lb 3 oz)
Supplied accessories
Operating Instructions (this manual)
Quick Setup Guide (1)
Optimizer microphone ECM-AC2 (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
AC power cord (mains lead) (1)
Remote commander RM-AAL003 (1)
R6 (size-AA) batteries (2)
Design and specifications are subject to
change without notice.
121GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Downmix 76
DVD player/DVD recorder
Playback 51
Symbols
Numerics
E
Equalizer 59
A
A.F.D. 72
H
HDMI
Adjusting
connecting 25
Audio 64
Equalizer 59
Level 58
Speaker 66
Surround 61
System 70
I
Tuner 63
Video 65
L
M
B
Menu
BI-AMP 101
Muting 49
C
CD player
Connecting 20
Playback 50
Conversion 33
D
DCS 74
N
Naming 90
Display 8
122GB
Download from Www.Somanuals.com. All Manuals Search And Download.
TV
O
Connecting 27
V
VCR
R
Recording
Connecting 32
Playback 53
Remote
Learning 109
X
Programming 104
Resetting 119
Z
S
Sound fields
Customizing 61
Resetting 79
Selecting 74
Speakers
Connecting 17
Super Audio CD player
Playback 50
T
Tuner
AM 80
FM 80
XM 83
Tuning
Automatically 80
Directly 81
123GB
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sony Projection Television 2 691 651 132 User Manual
Sound Performance Lab Musical Instrument PQ Mastering Equalizer User Manual
SOYO Personal Computer SY 6ZB User Manual
StarTechcom Power Screwdriver RK1236BKF User Manual
StarTechcom Switch ST4200MINI User Manual
Sterling Compact Loader SSIL Series User Manual
Sterling Thermostat S 6410 A User Manual
Sub Zero Refrigerator WS 30 O User Manual
Sunpentown Intl Air Conditioner WA 1010E User Manual
SVAT Electronics Home Security System CLEARVU6 User Manual