4-247-188-14(2)
FM Stereo
FM/AM Receiver
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No.
Serial No.
STR-DA5000ES
STR-DA3000ES
©2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
For customer in Canada
About This Manual
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
• The instructions in this manual are for model STR-
DA5000ES and STR-DA3000ES. Check your model
number by looking at the lower right corner of the
front panel. In this manual, STR-DA3000ES (area
code CEL) is used for illustration purposes unless
stated otherwise. Any difference in operation is
clearly indicated in the text, for example, “STR-
DA5000ES only”.
Except for European model
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY
STAR® guidelines for energy
efficiency.
• The instructions in this manual describe the controls
on the receiver. You can also use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see the separate operating
instructions supplied with the remote.
– STR-DA5000ES
RM-LJ312
– STR-DA3000ES
RM-LG112
– STR-DA5000ES/STR-DA3000ES
Models of area code U,CA only
RM-US106
About area codes
The area code of the receiver you purchased is
shown on the upper left portion of the rear panel
(see the illustration below).
FM
AM
4-XXX-XXX-XX AA
Area code
U
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
ANTENNA
RS232C
CTRL
A1
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
MULTI CHANNEL
INPUT
2
MD/DAT
OPTICAL
IN
R
PRE OUT
MD/DAT
OPTICAL
OUT
FRONT
CD/SACD
OPTICAL
IN
R
SURROUND BACK SPE
IMPEDANCE USE 4-16
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
**“DTS”, “DTS-ES Extended Surround”, and
“Neo:6” are trademarks of Digital Theater Systems,
Inc.
3GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Switching the audio input mode for digital
1: Check how to hookup your
components.......................................6
1a: Connecting components with
digital audio output jacks ...........8
1b: Connecting components with
multi channel output jacks........11
1c: Connecting components with only
analog audio jacks ....................13
6: Adjusting the speaker levels and
balance............................................22
Listening to the sound in another
zone ................................................ 52
List of button locations and reference
pages............................................... 64
Selecting the surround back decoding
4GB
Download from Www.Somanuals.com. All Manuals Search And Download.
5GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
1: Check how to hookup your components
connect each component.
Connectable components
Component to be connected
DVD player
Page
a)
With digital audio output
b)
With multi-channel audio output
c)
With analog audio output only
TV monitor
With component video input
With S-Video or composite video input only
Satellite tuner
With digital audio output
With analog audio output only
CD/Super Audio CD player
With digital audio output
d)
a)
c)
a)
10
b)
With multi-channel audio output
c)
With analog audio output only
MD/DAT deck
With digital audio output
a)
c)
With analog audio output only
Tape deck, Analog disc turntable
Multi-channel decoder
VCR, video camera, video game, etc.
a)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
Model with MULTI CH OUTPUT jacks, etc. This connection is used to output the audio decoded by the
component’s internal multi-channel decoder through this receiver.
b)
c)
d)
Model equipped only with AUDIO OUT L/R jacks, etc.
Model with component video (Y, P /C /B-Y, P /C /R-Y) input jacks.
B
B
R
R
6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cords (A to H) (not supplied).
A Audio cord
F Coaxial digital cord
White (L)
Red (R)
G Monaural audio cord
B Audio/video cord
Black
Yellow (video)
White (L/audio)
Red (R/audio)
Tip
Audio cord A can be torn into two monaural audio
cords G.
C Video cord
Yellow
H Component video cord
Green
Blue
D S-video cord
Red
E Optical digital cord
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the
components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
If you have Sony components with CONTROL A1II/CONTROL S
jacks
7GB
Download from Www.Somanuals.com. All Manuals Search And Download.
.
1a: Connecting components with digital audio output jacks
Hooking up a DVD player, TV monitor, or satellite tuner
1 Connect the audio jacks.
DVD player
T
AUDIO
OUT
L
DIGITAL
COAXIAL
DIGITAL
OPTICAL
R
F* E*
A
COMPONENT VIDEO
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
PR/CR
P
R/CR
/R-Y
P
R/CR
P
R/CR
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
E
A
T
DIGITAL
OPTICAL
AUDIO
OUT
L
R
Satellite tuner
* Connect to either the DVD COAXIAL IN or the DVD OPTICAL IN jack. We recommend making connections to
the DVD COAXIAL IN jack.
Note
You can listen to the sound of your TV by connecting your TV’s audio output jacks to the TV/SAT AUDIO IN jacks
on the receiver. In this case, do not connect the TV’s video output jack to the TV/SAT VIDEO IN jack on the
receiver.
8GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a TV or satellite tuner and a DVD player with
COMPONENT VIDEO (Y, P /C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component
B
B
R
R
video input jacks allows you to enjoy higher quality video. You can upconvert the video signals, and
Notes
• On this receiver, standard video signals can be converted to component video or S-video signals, and S-video
signals can be converted to component video signals. However, you cannot convert the component video signals
to standard video or S-video signals.
• When standard video signals (composite video signals) or S-video signals from a VCR etc. are converted upward
on this receiver and then output to your TV, depending on the status of the video signal output, the image on the
TV screen may appear distorted horizontally or no image may be output.
DVD player
TV monitor
H
C
D
H
D
C
COMPONENT VIDEO
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
PR/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
H
D
C
Satellite tuner
continued
9GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up a CD/Super Audio CD player or MD/DAT deck
CD/Super Audio
MD/DAT deck
CD player
T
AUDIO
OUT
L
OPTICAL
DIGITAL
OPTICAL
DIGITAL
COAXIAL
OUT
IN
R
*
*
A
E
F
E
E
A
A
IN
OUT
OUT
IN
COMPONENT VIDEO
ASSIGNABLE
DIGITAL
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
PR/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
DVD
COAXIAL
IN
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
SUB
WOOFER
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
* Connect to either the CD/SACD COAXIAL IN or the CD/SACD OPTICAL IN jack. We recommend making
connections to the CD/SACD COAXIAL IN jack.
If you want to connect several digital components, but cannot find an
unused input
Tips
• All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies.
• You can also connect an LD player with a DOLBY DIGITAL RF OUT jack via an RF demodulator (You cannot
connect an LD player’s DOLBY DIGITAL RF OUT jack directly to this unit’s digital input jacks). Refer to the
operating instructions supplied with the RF demodulator.
Notes
• No sound is output when playing a Super Audio CD disc on a Super Audio CD player connected to the CD/SACD
OPTICAL or COAXIAL IN jack on this receiver. Connect the player to the analog input jacks (CD/SACD IN
jacks). Refer to the operating instructions supplied with the Super Audio CD player.
• You cannot make digital recordings of digital multi channel surround signals.
10GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1b: Connecting components with multi channel output
jacks
1 Connect the audio jacks.
If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect
it to this receiver’s MULTI CHANNEL INPUT jacks to enjoy the multi channel sound. Alternatively,
the multi channel input jacks can be used to connect an external multi channel decoder.
COMPONENT VIDEO
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
OUT
OUT
PR/CR
P
R/CR
/R-Y
P
R/CR
P
R/CR
PR/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
AUDIO AUDIO
VARIABLE VARIABLE
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
2ND
ZONE
3RD
ZONE
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPU
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
U
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
MULTI CHANNEL
INPUT 2
MULTI CHANNEL INPUT 1
A A
G G
FRONT URROUND CENTER
L
R
SUB
WOOFER
DVD player,
Super Audio CD player,
Multi channel decoder, etc.
Tips
• This connection also allows you to enjoy software with multi-channel audio recorded in formats other than the
Dolby Digital and DTS.
• Make connections to either the MULTI CHANNEL INPUT 1 or MULTI CHANNEL INPUT 2 jacks according to
the number of audio output jacks of the component.
Note
DVD and Super Audio CD players do not have SURR BACK terminals.
continued
11GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a DVD player with COMPONENT VIDEO (Y, P /
B
C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component video input jacks allows you to
B
R
R
enjoy higher quality video. You can upconvert the video signals, and adjust the hue, etc. of the
Notes
• On this receiver, standard video signals can be converted to component video or S-video signals, and S-video
signals can be converted to component video signals. However, you cannot convert the component video signals
to standard video or S-video signals.
• When standard video signals (composite video signals) or S-video signals from a VCR etc. are converted upward
on this receiver and then output to your TV, depending on the status of the video signal output, the image on the
TV screen may appear distorted horizontally or no image may be output.
DVD player
TV monitor
H
C
D
H
D
C
FM
AM
COMPONENT VIDEO
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
PR/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
12GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1c: Connecting components with only analog audio jacks
Hooking up audio components
MD/DAT deck
INPUT
T
LINE
LINE
L
R
Turntable
A
A
A
OUT
IN
FM
AM
COMPONENT VIDEO
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
ANTENNA
MONITOR
OUT
CTRL
A1
IN
IN
OUT
IN
OUT
IN
PR/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
PR/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTR SPEKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
OUT
IN
A
A
A
T
INPUT
LINE
T
LINE
LINE
L
L
R
R
CD/Super Audio CD
player
Tape deck
Note
If your turntable has a ground wire, connect it to the U SIGNAL GND terminal.
continued
13GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up video components
If you connect your TV to the MONITOR jacks, you can watch the video from the selected input
(page 24). You can also display the SPEAKER SET UP, LEVEL, SURR SET UP, EQUALIZER,
CUSTOMIZE and TUNER menu settings and sound fields on your TV by pressing ON SCREEN on
the remote.
TV monitor
C
D
FM
AM
COMPONENT VIDEO
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
P
R/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
PR/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
R
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
L
B
AUDIO OUT
SURROUND BACK SPEAKER
SURROUND SPEAKERS
CENTER SPEAKER
FRONT SPEAKERS
IMPEDANCE USE 4-16
To the
VIDEO 3
INPUT jacks
(Front panel)
OUT
IN
OUT
IN
OUT
IN OUT
IN
B
,
D
D
D
B
B
B
B
D
D
Camcorderor
TV game
VCR
VCR
14GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Connecting the antennas
Connect the supplied AM loop antenna and FM wire antenna.
FM wire antenna
(supplied)
AM loop antenna
*
(supplied)
FM
AM
COMPONENT VIDEO
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
ANTENNA
CTRL
A1
P
R/CR
P
R/CR
/R-Y
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
CD/SACD
COAXIAL
IN
FRONT
SURROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULTI CHANNEL
INPUT
MULTI CHANNEL
INPUT
PHONO CD/SACD
MD/
2
1
MD/DAT
OPTICAL
IN
MD/DAT
OPTICAL
OUT
CD/SACD
OPTICAL
IN
R
L
SURROUND BACK SPEAKER
SURROUND SPEAKERS
IMPEDANCE USE 4-16
* The shape of the connector varies depending on the area code.
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
• Do not use the U SIGNAL GND terminal for grounding the receiver.
15GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Connecting speakers
Connect your speakers to the receiver. This receiver allows you to use a 7.1 channel system (except for
STR-DA3000ES models of area code CEL, TW) or 6.1 channel (STR-DA3000ES models of area code
CEL, TW only).
To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a
center speaker, and two surround speakers) and a sub woofer (5.1 channel).
You can enjoy high fidelity reproduction of DVD software recorded in the Surround EX format if you
connect one additional surround back speaker (6.1 channel) or two surround back speakers (7.1
channel. Except for STR-DA3000ES models of area code CEL, TW) (see “Selecting the surround back
Example of 7.1 channel speaker system configuration
Center speaker
Front speaker (R)
Surround speaker (R)
Front speaker (L)
Sub woofer
Surround speaker (L)
Surround back speaker (R)
Surround back speaker (L)
Tips
• When you connect 6.1 channel speaker system, place the surround back speaker behind the listening position.
• Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
16GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
A Speaker cords (not supplied)
B Monaural audio cord (not supplied)
(+)
(–)
Black
Surround back
speaker (R)*
Surround back
speaker (L)*
Front speaker (R)
Front speaker (L)
E
e E
e E
e E
e
A
A
A
A
FM
AM
U
COMPONENT VIDEO
75 COAXIAL
ASSIGNABLE
DIGITAL
DVD
COAXIAL
IN
MONITOR OUT
TV/SAT IN
DVD IN
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
MONITOR
ANTENNA
CTRL
A1
IN
IN
OUT
IN
OUT
IN
OUT
PR/CR
P
R/CR
/R-Y
PR/CR
P
R/CR
P
R/CR
PR/CR
/R-Y
Y
Y
Y
/B-Y
/B-Y
/R-Y
/B-Y
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
CD/SACD
COAXIAL
IN
FRONT
RROUND SURR BACK CENTER
FRONT
SURROUND CENTER SIGNAL GND
IN
IN
OUT
IN
OUT
IN
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L
R
DVD
OPTICAL
IN
TV/SAT
OPTICAL
IN
SUB
WOOFER
SUB
WOOFER
MULCHANNEL
PUT
MULTI CHANNEL
PHONO CD/SACD
MD/DAT
TAPE
TV/SAT DVD
VIDEO 2
VIDEO 1
2
INPUT
1
MD/DAT
OPTICAL
IN
SUB
WOOFER
R
L
R
L
R
L
PRE OUT
MD/DAT
OPTICAL
OUT
FRONT
SURROUND
SURROUND BACK
CENTER
AUDIO OUT
R
L
A
SUB
WOOFER
CD/SACD
OPTICAL
IN
R
L
R
L
AUDIO OUT
SURROUND BACK SPEAKERS
SURROUND SPEAKERS
CENTER SPEAKER
IMPEDANCE USE 4-16
(Except for
FRONT
models of
area code
U, CA)
SPEAKERS B**
(Models of area
code U, CA only)
A
A
A
B
INPUT
AUDIO
IN
e
E
E
e E
e
Surround speaker
(R)
Surround speaker
(L)
Center speaker
Sub woofer
* If you connect only one surround back speaker, connect it to the SURROUND BACK SPEAKERS L terminal
(except for STR-DA3000ES models of area code CEL, TW).
STR-DA3000ES models of area code CEL, TW have only one SURROUND BACK SPEAKER terminal.
**You can select the front speakers you want to use with SPEAKERS. For details, see “Selecting the speaker system”
Tip (Models of area code U, CA only)
To connect certain speakers to another power amplifier, use the PRE OUT jacks. The same signal is output from both
the SPEAKERS jacks and the PRE OUT jacks. For example, if you want to connect just the front speakers to another
amplifier, connect that amplifier to the PRE OUT FRONT L and R jacks.
17GB
Download from Www.Somanuals.com. All Manuals Search And Download.
fans, or TVs to this outlet. This may cause a
malfunction.
4: Connecting the AC
power cord
Before using the receiver
Connect the supplied AC power cord to the AC
IN terminal on the receiver, then connect the AC
power cord to a wall outlet.
Performing initial setup
operations
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure.
This procedure can also be used to return
settings you have made to their factory defaults.
AC power cord
1 Press ?/1 on the receiver to turn off the
receiver.
2 Hold down ?/1 on the receiver for 5
seconds.
*
AC OUTLET
3 While “ENTER to Clear All” appears in the
display, press MEMORY/ENTER on the
receiver.
After “MEMORY CLEARING...” appears in
the display for a while, “MEMORY
CLEARED!” appears.
S2 VIDEO S2 VIDEO S2 VIDEO
IN
OUT
IN
VIDEO
VIDEO
VIDEO
The following are reset to their factory
settings.
AUDIO
AUDIO
AUDIO
• All settings in the SPEAKER SET UP,
LEVEL, SURR SET UP, EQUALIZER,
CUSTOMIZE, TUNER and CIS (models
of area code U, CA only) menus.
• The sound field memorized for each input
and preset station.
AC OUTLET
EO 2
VIDEO 1
L
A
SUB
WOOFER
L
B
AUDIO OUT
RONT SPEAKERS
• All preset stations.
• All index names for inputs and preset
stations.
Note
AC IN
terminal
If “2nd zone on” or “3rd zone on” appears in the
display, the initial setup operation cannot be
performed. Turn off the indication by following the
first tip of “Listening to the sound in another zone”
* The configuration, shape, and number of AC outlets
vary according to the area code.
Notes
Before using the remote for the
first time (STR-DA5000ES only)
• The AC OUTLET(s) on the rear of the receiver is a
switched outlet, which supplies power to the
connected component only while the receiver is
turned on.
When you use the remote for the first time, be
sure to perform the following procedure. The
remote is optimized for the receiver.
• Make sure that the total power consumption of the
component(s) connected to the receiver’s AC
OUTLET(s) does not exceed the wattage stated on
the rear panel. Do not connect high-wattage
electrical home appliances such as electric irons,
1 Press RM SET UP.
18GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Move the easy scroll key to select “AMP
REGIST”, then press the key to enter the
selection.
5: Setting up the speakers
You can use the SPEAKER SET UP menu to set
the size and distance of the speakers connected
to this system.
3 If the displayed model name is same as the
model you use, select “Exit”. If a different
model name or “? ? ?” appears, move the
easy scroll key to select “START”, then
press the key to enter the selection.
1
2
Press ?/1 to turn on the system.
Rotate MAIN MENU to select
“SPEAKER SET UP”.
After “SEARCHING” appears, the model
name appears. Make sure to keep the remote
pointing toward the receiver until the model
name appears. The remote is reset, turns off,
and optimized for the model. The customized
settings of the remote is cleared and reset to
their factory settings.
3
Rotate MENU to select the menu item
you want.
For more information, see “Speaker setup
Notes
• Certain setup parameters may be dimmed in the
display. This means that the selected parameter
is either unavailale or fixed and unchangeable
settings.
• Some speaker setup items may appear dimmed
in the display. This means that they have been
adjusted automatically due to other speaker
settings. Depending on the settings, you may or
may not be able to adjust certain speakers.
4
5
Rotate –/+ to select the parameter.
all of the items that follow.
Speaker setup parameters
The initial settings are underlined.
x SP EASY SET UP (Speaker easy setup)
• YES
You can set up your speakers automatically
by selecting a pre-defined speaker pattern (see
the supplied “Easy Setup Guide”).
• NO
Select to adjust the settings of each speaker
manually.
x SPEAKER PATTERN
(Speaker setup pattern)
When “SP EASY SET UP” is set to “YES”,
select the speaker setup pattern. Rotate –/+ to
select the speaker setup pattern and press
MEMORY/ENTER to enter the selection.
continued
19GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Check your speaker pattern using the supplied
“Easy Setup Guide”.
When the multi channel input is selected,
analog downmixing is performed.
x SUB WOOFER (Sub woofer)
x SURROUND SP
(Surround speakers)
• YES
The surround back speakers are set to the same
setting.
If you connect a sub woofer, select “YES”.
• NO
• LARGE
If you did not connect a sub woofer, select
“NO”. This activates the bass redirection
circuitry and outputs the LFE signals from
other speakers.
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the surround
speakers to “LARGE”.
x FRONT SP (Front speakers)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
When the sub woofer is set to “NO”, front
speakers are automatically set to “LARGE”.
• SMALL
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL”, the center, surround and surround
back speakers are also automatically set to
“SMALL” (unless previously set to “NO”).
If you did not connect surround speakers,
select “NO”.
x SURR BACK SP
(Surround back speakers)
When the surround speakers are set to “NO”, the
surround back speakers are also automatically
set to “NO” and the setting cannot be changed.
x CENTER SP (Center speaker)
Except for STR-DA3000ES models of area
code CEL, TW
• LARGE
If you connect a large speaker that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the center speaker
to “LARGE”.
• DUAL
If you connect two surround back speakers,
select “DUAL”. The sound will be output to a
maximum of 7.1 channels.
• SINGLE
If you connect only one surround back
speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
• NO
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the front
speakers (if set to “LARGE”) or sub woofer.
• NO
If you did not connect surround back
speakers, select “NO”.
STR-DA3000ES models of area code CEL,
TW only
• YES
If you did not connect a center speaker, select
“NO”. The sound of the center channel will be
output from the front speakers.
If you connect a surround back speaker, select
“YES”.
20GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• NO
If you did not connect surround back speaker,
select “NO”.
When placing two surround back speakers
(The angle B should be the same)
Tip
The “LARGE” and “SMALL” settings for each
speaker determine whether or not the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
A
A
30˚ 30˚
100˚-120˚
100˚-120˚
B
B
B
However, it best not to cut them, if possible. Therefore,
even when using small speakers, you can set them to
“LARGE” if you want to output the bass frequencies
from that speaker. On the other hand, if you are using
a large speaker, but prefer not to have bass frequencies
output from that speaker, set it to “SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the equalizer to boost the bass levels. To
x CENTER XXX meter*
(Center speaker distance)
Initial setting: 3.0 meter (10 feet)
Lets you set the distance from your listening
position to the center speaker. You can adjust
from 1.0 meter to 7.0 meters (3 to 23 feet) in 0.1
meter (1 foot) steps.
x FRONT XXX meter*
(Front speaker distance)
x SURROUND XXX meter*
(Surround speaker distance)
Initial setting: 3.0 meter (10 feet)
Initial setting: 3.0 meter (10 feet)
Lets you set the distance from your listening
position to the front speakers (A). You can
adjust from 1.0 meter to 7.0 meters (3 to 23 feet)
in 0.1 meter (1 foot) steps.
If both front speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
Lets you set the distance from your listening
position to the surround speakers. You can
adjust from 1.0 meter to 7.0 meters (3 to 23 feet)
in 0.1 meter (1 foot) steps.
If both surround speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
x SURR BACK XXX meter*
(Surround back speaker distance)
When placing only one surround back speaker
Initial setting: 3.0 meter (10 feet)
Lets you set the distance from your listening
position to the surround back speaker. You can
adjust from 1.0 meter to 7.0 meters (3 to 23 feet)
in 0.1 meter (1 foot) steps.
A
A
30˚ 30˚
100˚-120˚
100˚-120˚
If you connect two surround back speakers and
both surround back speakers are not placed an
equal distance from your listening position
(Except for STR-DA3000ES models of area
code CEL, TW), set the distance to the closest
speaker.
x SUB WOOFER XXX meter*
(Sub woofer distance)
Initial setting: 3.0 meter (10 feet)
Lets you set the distance from your listening
position to the sub woofer. You can adjust from
21GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 meter to 7.0 meters (3 to 23 feet) in 0.1 meter
(1 foot) steps.
6: Adjusting the speaker
levels and balance
— TEST TONE
* For models of area code U, CA, “X feet” is
displayed.
Tip
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set the
center speaker further than the front speakers. Also, the
center speaker cannot be set more that 1.5 meters (5
feet) closer than the front speakers.
Adjust the speaker levels and balance while
listening the test tone from your listening
position. Use the remote for the operation.
For details on the remote operation, refer to the
operating instructions supplied with the remote.
Likewise, the surround speakers can not be set farther
away from the listening position than the front
speakers. And they can be no more than 4.5 meters (15
feet) closer.
Tip
The receiver employs a test tone with a frequency
centered at 800 Hz.
This is because incorrect speaker placement is not
conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer
than the actual location of the speakers will cause a
delay in the output of the sound from that speaker. In
other words, the speaker will sound like it is farther
away.
1
2
Press ?/1 on the remote to turn on the
receiver.
RM-LJ312:
Press < on the remote repeatedly until
RECEIVER menu appears.
Move the easy scroll key to select
“TEST TONE”, then press the key to
enter the selection.
For example, setting the center speaker distance 1–2
meters (3–6 feet) closer than the actual speaker
position will create a fairly realistic sensation of being
“inside” the screen. If you cannot obtain a satisfactory
surround effect because the surround speakers are too
close, setting the surround speaker distance closer
(shorter) than the actual distance will create a larger
sound stage.
RM-LG112:
Press TEST TONE on the remote.
“TEST TONE” in the LEVEL menu
appears in the display and the test tone is
output from each speaker in sequence.
Adjusting these parameter while listening to the sound
often results in much better surround sound. Give it a
try!
3
4
Adjust the speaker level and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For advanced speaker setups
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON”. This enables advanced
setups including those of the heights of the
surround speakers.
For details on the LEVEL menu settings,
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/– on the remote or
turn MASTER VOLUME on the receiver.
• You can also use –/+ on the receiver for the
adjustment.
RM-LJ312:
After the adjustment, press < on the
remote repeatedly again until
RECEIVER menu appears.
Move the easy scroll key to select
“TEST TONE”, then press the key
repeatedly to select “TEST TONE
[OFF]”.
22GB
Download from Www.Somanuals.com. All Manuals Search And Download.
RM-LG112:
Press TEST TONE again.
The test tone turns off.
To output the test tone only from
a specific speaker
Set “TEST TONE” in the LEVEL menu to
from the selected speaker.
For more precise adjustment
You can output the test tone or sound source
from two adjacent speakers to adjust their
balance and level.
Set “MENU EXPAND” in the CUSTOMIZE
speakers you want to adjust using “PHASE
NOISE” or “PHASE AUDIO” in the LEVEL
23GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on using headphones
• When headphones are connected, you can select only
– HEADPHONE (2CH)
Amplifier Operation
Selecting the component
– HEADPHONE (DIRECT)
– HEADPHONE (MULTI 1)
1
Rotate INPUT SELECTOR to select the
input.
– HEADPHONE (MULTI 2)
– HEADPHONE THEATER
• When headphones are connected and you use the
channels may not output depending on the speaker
settings.
The selected input appears in the display.
To select the
Display
VCR
VIDEO 1 or
VIDEO 2
Camcorder or TV game
DVD player
VIDEO 3
DVD
Satellite tuner
TV/SAT
TAPE
Tape deck
MD or DAT deck
MD/DAT
CD/SACD
CD or Super Audio CD
player
Built-in tuner
FM or AM and
frequency
Turntable
PHONO
2
3
Turn on the component and start
playback.
Rotate MASTER VOLUME to adjust the
volume.
To mute the sound
Press MUTING on the remote. To cancel, press
MUTING on the remote again or turn MASTER
VOLUME clockwise to raise the volume. Even
if you turn off the receiver, the muting function
works when you turn on the receiver again.
24GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to multi channel
sound
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
— MULTI CH IN
You can select the audio directly from the
components connected to the MULTI
CHANNEL INPUT jacks. This enables you to
enjoy high quality analog inputs like DVD or
Super Audio CD.
Tip
The tuning scale for direct tuning differs depending on
the area code as shown in the following table. For
details on area codes, see page 3.
Surround effects are not activated when using
this input.
Area code
U, CA
FM
AM
100 kHz
50 kHz
10 kHz*
9 kHz
Press MULTI CH IN 1/2 repeatedly to select
the multi channel audio source (“MULTI CH
1 DIRECT” or “MULTI CH 2 DIRECT”).
CEL, TW
The selected audio source is output.
Automatic tuning
When a center speaker or sub
woofer is not connected
1
Rotate INPUT SELECTOR to select
tuner (“FM” or “AM”).
If you have set the center speaker to “NO”, or set
the sub woofer to “NO” in the SPEAKER SET
MULTI CH IN function, the analog center or
sub woofer audio will be output from the front
left and right speakers.
2
3
Press FM/AM to select “FM” or “AM”.
Press TUNING + or TUNING –.
Press TUNING + to scan from low to high;
press TUNING – to scan from high to low.
The receiver stops scanning whenever a
station is received.
In case of poor FM stereo
reception
If the FM stereo reception is poor and
“STEREO” flashes in the display, select
monaural audio so that the sound will be less
distorted.
1 Rotate MAIN MENU to select “TUNER”.
2 Rotate MENU to select “FM MODE”.
3 Rotate –/+ to select “MONO”.
The FM reception switches to monaural.
continued
25GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 2: AM 1,350 kHz
Direct tuning
Select 1 b 3 b 5 b 0
(You do not have to enter the last “0” when
the tuning scale is set to 10 kHz.)
If you have tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
Enter a frequency of the station directly by using
NUM menu or numeric buttons on the remote.
For details on the supplied remote, refer to the
operating instructions supplied with the remote.
R1M-LJ312
Press INPUT SELECTOR, then select
If you cannot tune in a station
and the entered numbers flash
“TUNER” from the input list.
You can also use INPUT SELECTOR on
the receiver.
Make sure you have entered the right frequency.
If not, repeat step 4 (RM-LJ312) or step 3 (RM-
LG112). If the entered numbers still flash, the
frequency is not used in your area.
2
Press > repeatedly until SUB menu
appears, then select “FM/AM” from the
SUB menu to select the FM or AM band.
You can also use FM/AM on the receiver.
3
4
Select “DIRECT TUNING” from the SUB
menu.
Press > on the remote repeatedly until
NUM menu appears, then select the
numbers for the frequency.
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 b 0
(You do not have to enter the last “0” when
the tuning scale is set to 100 kHz.)
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
(You do not have to enter the last “0” when
the tuning scale is set to 10 kHz.)
If you have tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
R1M-LG112
Move the easy scroll key to select
“TUNER”, then press the key
repeatedly to select “FM” or “AM”.
You can also use INPUT SELECTOR on
the receiver.
2
3
Press ALT, then press D.TUNING on
the remote.
Press the numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 b 0
(You do not have to enter the last “0” when
the tuning scale is set to 100 kHz.)
26GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing FM stations
automatically
Presetting radio stations
You can preset up to 30 FM or AM stations.
Then you can easily tune in the stations you
often listen to.
— AUTOBETICAL
(Models of area code CEL only)
This function lets you store up to 30 FM and FM
RDS stations in alphabetical order without
redundancy. Additionally, it only stores the
stations with the clearest signals.
Presetting radio stations
1
Rotate INPUT SELECTOR to select
tuner (“FM” or “AM”).
If you want to store FM or AM stations one by
2
3
Press FM/AM to select “FM” or “AM”.
Tune in the station that you want to
preset using Automatic Tuning
1
2
Press ?/1 to turn off the receiver.
Hold down MEMORY/ENTER and press
?/1 to turn the receiver back on.
Switch the FM reception mode if necessary
“Autobetical select” appears in the display
and the receiver scans and stores all the FM
and FM RDS stations in the broadcast area.
For RDS stations, the tuner first checks for
stations broadcasting the same program,
then stores only the one with the clearest
signal. The selected RDS stations are sorted
alphabetically by their Program Service
name, then assigned a 2-character preset
code. For more details on RDS, see
4
5
Press MEMORY/ENTER.
“MEMORY” appears in the display for a
display goes out.
Press PRESET TUNING + or PRESET
TUNING – to select a preset number.
If you want to switch the memory page,
press SHIFT on the remote.
If “MEMORY” goes out before you select
the preset number, start again from step 4.
Regular FM stations are assigned 2-
character preset codes and stored after the
RDS station.
6
7
Press MEMORY/ENTER again.
The station is stored to the selected preset
number.
When done, “Autobetical finished” appears
in the display momentarily and the receiver
returns to the normal operation.
If “MEMORY” goes out before you press
MEMORY/ENTER, start again from step
Notes
• Do not press any button on the receiver or supplied
remote during autobetical operation, except ?/1.
• If you move to another area, repeat this procedure to
store stations in your new area.
station.
Tuning to preset stations
• If you move the antenna after storing stations with
this procedure, the stored settings may no longer be
valid. If this happens, repeat this procedure to store
the stations again.
1
2
Rotate INPUT SELECTOR to select
tuner (“FM” or “AM”).
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select the
preset station you want.
continued
27GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Each time you press the button, you can
select the preset station as follows:
Using the Radio Data
System (RDS)
tA1yA2y...yA0yB1yB2y...yB0T
tC0y...yC2yC1T
(Models of area code CEL only)
This receiver also allows you to use RDS (Radio
Data System), which enables radio stations to
send additional information along with the
regular program signal. You can display RDS
information.
Using the remote
RM-LJ312
1 Press INPUT SELECTOR, then move the
easy scroll key to select “TUNER” from the
input list.
2 Move the easy scroll key to select the preset
number you want, then press the key to
enter the selection.
Receiving RDS broadcasts
Simply select a station on the FM band
RM-LG112
1 Move the easy scroll key to select “TUNER”,
then press the key repeatedly to select “FM”
or “AM”.
When you tune in a station that provides RDS
services, the RDS indicator lights up and the
program service name appears in the display.
2 Press D.SKIP/CH/PRESET +/– repeatedly
to select the preset station you want.
Note
RDS may not work properly if the station you tuned to
is not transmitting the RDS signal properly or if the
signal strength is weak.
Displaying RDS information
While receiving an RDS station, press
DISPLAY.
Each time you press the button, RDS
information on the display changes cyclically as
follows:
Top level
One of the followings, band, and preset number
is displayed:
a)
• PS (Program Service name)
b)
• Present station name
• Frequency
Lower level
c)
PTY (Program Type) indication t RT (Radio
d)
Text) indication t CT (Time) indication (in
24-hour system level) t Sound field currectly
applied
a)
This information also appears for non-RDS FM
stations.
b)
Appears only when the preset station is indered.
c)
d)
Text messages sent by the RDS station.
28GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Program type
indication
Description
• If there is an emergency announcement by
government authorities, “Alarm-Alarm!” flashes in
the display.
Social Affairs
Programs about people and the
things that affect them
• If a station does not provide a particular RDS service,
“No XX” (such as “No Clock Time”) appears in the
display.
Religion
Phone In
Programs of religious content
Programs where members of the
public express their views by
phone or in a public forum
• When a station broadcasts radio text data, it is
displayed at the same rate at which it is sent from the
station. Any change in this rate is reflected in the
display rate of the data.
Travel & Touring Programs about travel. Not for
announcements that are located by
TP/TA.
Leisure & Hobby Programs on recreational
activities such as gardening,
Description of program types
fishing, cooking, etc.
Program type
indication
Description
Jazz Music
Jazz programs
News
News programs
Country Music
Country music programs
Current Affairs Topical programs that expand on
current news
National Music Programs featuring the popular
music of the country or region
Information
Programs offering information on
a wide spectrum of subjects,
including consumer affairs and
medical advice
Oldies Music
Folk Music
Documentary
None
Programs featuring oldies music
Folk music programs
Investigative features
Any programs not defined above
Sport
Sports programs
Education
Educational programs, such as
“how-to” and advice programs
Drama
Radio plays and serials
Cultures
Programs about national or
regional culture, such as language
and social concerns
Science
Programs about the natural
sciences and technology
Varied Speech
Other types of programs such as
celebrity interviews, panel games,
and comedy
Pop Music
Popular music programs
Rock music programs
Easy Listening
Rock Music
M.o.R. Music
Light Classics M Instrumental, vocal, and choral
music
Serious Classics Performances of major orchestras,
chamber music, opera, etc.
Other Music
Music that does not fit into any
categories above, such as Rhythm
& Blues and Reggae
Wether & Metr Weather information
Finance Stock market reports and trading,
etc.
Children’s Progs Programs for children
29GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the display
Changing the information in
the display
You can check the sound field etc. by changing
the information in the display.
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display will
change as follows.
All inputs except “FM” and “AM”
Index name and sound field name* y Input
name and sound field name
FM and AM
Preset station name and sound field name* y
Input name and sound field name
* Index name appears only when you have assigned
name does not appear when only blank spaces have
been entered, or it is the same as the input name.
Displaying the input stream
information
You can check the input stream information
(about format, channel, etc.) of digital input
signals. The input stream information also
appears for 4 seconds when the receiver detects
any changes in the digital input signal.
1
2
Rotate MAIN MENU to select “STREAM
INFO”.
Rotate MENU.
The input stream information appears.
3
Rotate –/+ for more information.
30GB
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indications in the display
1
2
3 4
5
6
7
8
9
q;
qa
qs qd
SW
L
C
R
INPUT AUTO I.LINK
;
;
;
RF COAX OPTANALOG MULTI CH IN 1 2
DIGITAL EX DTS-ES 96/24
SLEEP
D.RANGE
PRO LOGIC II NEO:6 DISCRETE H.A.T.S. SB DEC RDS EQ
MOVIE MUSIC CINEMA MATRIX STEREO MONO MEMORY
SL
S
SR
L.F.E.
SBL
SB
SBR
wf
wd ws
wa w; ql qk qj qh
qg
qf
A SW: Lights up when sub woofer selection is
lights up, the receiver creates a sub woofer
signal based on the LFE signal in the disc
being played back or the low frequency
components of the front channels. This
indicator does not light during the 2CH
STEREO mode.
D INPUT: Lights up constantly. One of the input
indicators also lights up according to the
current input.
E AUTO: Lights up when INPUT MODE is set
F DTS (-ES): Lights up when DTS signals are
input. “-ES” lights up when DTS-ES signals
are input. When playing a DTS format disc, be
sure that you have made digital connections
and that INPUT MODE is NOT set to
B Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the receiver downmixes the
source sound (based on the speakers settings).
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing)), SBL (Surround back
Left), SBR (Surround back right), SB
(Surround Back (the surround back
G COAX: Lights up when the source signal is a
digital signal being input through the
COAXIAL terminal or when INPUT MODE
H OPT: Lights up when the source signal is a
digital signal being input through the
OPTICAL terminal, or when INPUT MODE
components obtained by 6.1 channel
decoding))
I ANALOG: Lights up when no digital signal is
input to COAXIAL or OPTICAL jack, or
when INPUT MODE is set to “ANALOG
Example:
Recording format (Front/Surround): 3/2
Output channel: Surround speakers absent
Sound Field: A.F.D. AUTO
A.F.D. 2CH SW in the SURR SET UP menu:
CREATE
J MULTI CH IN 1/2: Lights up when “MULTI
CH 1 DIRECT” or “MULTI CH 2 DIRECT”
is selected.
(The initial setting is “OFF”)
K SB DEC: Lights up when surround back
SW
L
C
R
SL
SR
L SLEEP: Lights up when sleep timer is
C ; DIGITAL (EX): Lights up when Dolby
Digital signals are input. “EX” lights up when
Dolby Digital EX signals are input. When
playing a Dolby Digital format disc, be sure
that you have made digital connections and
that INPUT MODE is NOT set to “ANALOG
activated.
M D.RANGE: Lights up when dynamic range
compression is activated (page 46).
N EQ: Lights up when the equalizer is activated.
continued
31GB
Download from Www.Somanuals.com. All Manuals Search And Download.
O Tuner indicators: Lights up when using the
receiver to tune in radio stations, etc. See
P 96/24: Lights up when the receiver is
decoding DTS 96 kHz/24 bit signals.
Q MATRIX: Lights up when DTS-ES Matrix
decoding is activated.
R DISCRETE: Lights up when DTS-ES
Discrete decoding is activated.
S CINEMA: Lights up when DTS Neo:6
Cinema decoding is activated.
T NEO:6: Lights up when DTS Neo:6 Cinema/
Music decoding is activated.
U MUSIC: Lights up when Pro Logic II Music
or DTS Neo:6 Music decoding is activated.
V MOVIE: Lights up when Pro Logic II Movie
decoding is activated.
W ; PRO LOGIC (II): Lights up when the
receiver applies Pro Logic processing to 2
channel signals in order to output the center
and surround channel signals. This indicator
also lights when the Pro Logic II Movie/Music
decoder is activated. However, this indicator
does not light if both the center and surround
speakers are set to “NO”.
X L.F.E.: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel. When the sound of the LFE
channel signal is actually being reproduced,
the bars underneath the letters lights up to
indicate the level. Since the LFE signal is not
recorded in all parts of the input signal the bar
indication will fluctuate (and may turn off)
during playback.
32GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying higher fidelity
sound
Enjoying Surround Sound
Using only the front
speakers
— AUTO FORMAT DIRECT
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
In this mode, the receiver outputs the sound
from the front L/R speakers only. There is no
sound from the sub woofer.
A.F.D. mode
Decoding mode
As encoded
AUTO
PRO LOGIC
Dolby Pro Logic
Listening to 2 channel stereo
sources (2CH STEREO)
PRO LOGIC II MOVIE
PRO LOGIC II MUSIC
Neo:6 Cinema
Dolby Pro Logic II
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
DTS Neo:6
Neo:6 Music
MULTI STEREO
Press 2CH.
Decoding the input audio
signal automatically
“2CH STEREO” appears in the display and the
receiver switches to the 2CH STEREO mode.
Note
In this mode, the receiver automatically detects
the type of audio signal being input (Dolby
Digital, DTS, standard 2 channel stereo, etc.)
and performs the proper decoding if necessary.
This mode presents the sound as it was recorded/
encoded, without adding any surround effects.
However, when “A.F.D. 2CH SW” in the SURR
SET UP menu is set to “CREATE” and if there
are no low frequency signals (Dolby Digital
LFE, etc.) it will generate a low frequency signal
for output to the sub woofer.
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to the 2 channel stereo
sources using the front L/R speakers and a sub woofer,
select “A.F.D. AUTO” and set “A.F.D. 2CH SW” in
the SURR SET UP menu to “CREATE”.
Press A.F.D. repeatedly to select “A.F.D.
AUTO”.
The receiver automatically detects the type of
audio signal being input and performs the proper
decoding if necessary.
Tip
In most cases, “A.F.D. AUTO” provides the most
appropriate decoding. You may want to use SURR
stream to the mode you prefer.
continued
33GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying stereo sound in multi
channel (2 channel decoding
mode)
Selecting a sound field
You can take advantage of surround sound
simply by selecting one of the receiver’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
This mode lets you specify the type of decoding
for 2 channel audio sources. This receiver can
reproduce 2 channel sound in 5 channels
through Dolby Pro Logic II; 6 channels through
DTS Neo:6; or 4 channels through Dolby Pro
Logic. However, DTS 2CH sources are not
decoded by DTS Neo:6; they are output in 2
channels.
Selecting a sound field for
movies
Press MOVIE repeatedly to select the
sound field you want.
Press A.F.D. repeatedly to select the 2
channel decoding mode.
The selected sound field appears in the display.
x PRO LOGIC
Sound field
Performs Dolby Pro Logic decoding. The source
recorded in 2 channel is decoded into 4.1 channels.
CINEMA STUDIO EX A DCS
CINEMA STUDIO EX B DCS
CINEMA STUDIO EX C DCS
V.MULTI DIMENSION DCS
x PRO LOGIC II MOVIE
Performs Dolby Pro Logic II Movie mode decoding.
This setting is ideal for movies encoded in Dolby
Surround. In Addition, this mode can reproduce sound
in 5.1 channel when watching videos of overdubbed or
old movies.
About DCS (Digital Cinema
Sound)
x PRO LOGIC II MUSIC
Sound fields with DCS marks use DCS
technology.
Performs the Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal stereo
sources such as CDs.
DCS is the concept name of the surround
technology for home theater developed by Sony.
DCS uses the DSP (Digital Signal Processor)
technology to reproduce the sound
characteristics of an actual cinema cutting studio
in Hollywood.
When played at home, DCS will create a
powerful theater effect that mimics the artistic
combination of sound and action as envisioned
by the movie director.
x Neo:6 Cinema
Performs the DTS Neo:6 Cinema mode decoding.
x Neo:6 Music
Performs the DTS Neo:6 Music mode decoding. This
setting is ideal for normal stereo sources such as CDs.
x MULTI STEREO
Outputs the 2 channel L/R signals from all speakers.
If you connect a sub woofer
x CINEMA STUDIO EX A DCS
When the source signal does not include a LFE
signal, the receiver generates a low frequency
signal for output to the sub woofer. However the
low frequency signal is not generated for “Neo:6
Cinema” or “Neo:6 Music” when all speakers
are set to “LARGE”.
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Cary Grant Theater” cinema
production studio. This is a standard mode, great for
watching most any type of movies.
x CINEMA STUDIO EX B DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Kim Novak Theater” cinema
production studio. This mode is ideal for watching
science-fiction or action movies with lots of sound
effects.
34GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x CINEMA STUDIO EX C DCS
Sound field
Reproduces the sound characteristics of the Sony
Pictures Entertainment scoring stage. This mode is
ideal for watching musicals or films where orchestra
music is featured in the soundtrack.
D.CONCERT HALL A
D.CONCERT HALL B
CHURCH
x V.MULTI DIMENSION DCS
Creates 5 sets of virtual speakers from a single pair of
actual surround speakers.
JAZZ CLUB
LIVE CONCERT
STADIUM
About CINEMA STUDIO EX modes
SPORTS
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in your
home.
x D.CONCERT HALL A
Uses 3D sound imaging to reproduce the sound
characteristics of the CONCERTGEBOUW in
Amsterdam, which is famous for a large sound stage
produced by reflectivity.
x D.CONCERT HALL B
The CINEMA STUDIO EX modes consist of
the following three elements.
Uses 3D sound imaging to reproduce the sound
characteristics of the MUSIKVEREIN in Vienna,
which is famous for its hall resonance and unique
reverberative sound.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a single
pair of actual surround speakers.
x CHURCH
• Screen Depth Matching
Reproduces the acoustics of a stone church.
Creates the sensation that the sound is coming
from inside the screen like in theaters.
• Cinema Studio Reverberation
x JAZZ CLUB
Reproduces the acoustics of a jazz club.
x LIVE CONCERT
Reproduces the type of reverberation found in
theaters.
Reproduces the acoustics of a 300-seat live house.
x STADIUM
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
Reproduces the feeling of a large open-air stadium.
x SPORTS
Tip
Reproduces the feeling of sports broadcasting.
You can identify the encoding format of DVD
software, etc. by looking at the logo on the package.
When the headphones are
connected
–
–
–
: Dolby Digital discs
: Dolby Surround encoded programs
: DTS Digital Surround encoded programs
You can select only from the following sound
fields.
Notes
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
x HEADPHONE (2CH)
Press 2CH or A.F.D. Outputs the sound in 2 channel
(stereo). Standard 2 channel stereo sources completely
bypass the sound field processing and multi channel
surround formats are downmixed to 2 channels.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
x HEADPHONE (DIRECT)
Press DIRECT. Outputs the signals without digital
processing by the equalizer, sound field, etc.
Selecting a sound field for
music
x HEADPHONE (MULTI 1/MULTI 2)
Press MUSIC repeatedly to select the
sound field you want.
Press MULTI CH 1/2. Outputs the analog signals input
to the MULTI CHANNEL INPUT jacks.
The selected sound field appears in the display.
continued
35GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x HEADPHONE THEATER DCS
Allows you to experience a theater-like environment
while listening through a pair of headphones.
Selecting the surround
back decoding mode
— SURR BACK DECODING
To turn off the surround effect
Press 2CH, or press A.F.D. to select “A.F.D.
AUTO”.
This function lets you select the decoding mode
for the surround back signals of the multi
channel input stream.
By decoding the surround back signal of DVD
software (etc.) recorded in Dolby Digital EX,
DTS-ES Matrix, DTS-ES Discrete 6.1, etc.
format, you can enjoy the surround sound
intended by the filmmakers.
Enjoying the surround effect
at low volume level
(NIGHT MODE)
(STR-DA5000ES only)
This function allows you to retain a theater like
environment at low volume levels. This function
can be used with other sound fields.
When watching a movie late at night, you will be
able to hear the dialog clearly even at a low
volume level.
Press SURR BACK DECODING repeatedly
to select the surround back decoding
mode.
For details, see “How to select the surround back
R1M-LJ312
Press < repeatedly to select the
RECEIVER menu.
Tip
You can select the surround back decoding mode using
“SB DECODING” in the CUSTOMIZE menu
2
Move the easy scroll key to select
“NIGHT MODE”, then press the key to
enter the selection.
The NIGHT MODE function is activated.
Tip
While this function is on, the BASS, TREBLE, and
EFFECT level increase, and “D.RANGE COMP.” is
Note
This function cannot be activated when MULTI CH IN
or DIRECT function is activated.
Listening to the sound
without any adjustment
You can listen to the sound without adjusting the
equalizer and surround effect.
Press DIRECT.
The DIRECT indicator lights up and the
equalizer and sound fields are canceled.
36GB
Download from Www.Somanuals.com. All Manuals Search And Download.
How to select the surround back decoding mode
You can select the surround back mode you want according to the input stream.
When you select “AUTO”
a)
When the input stream contains the 6.1 channel decode flag , the appropriate decoder is applied to
decode the surround back signal.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
e)
5.1
—
b)
e)
6.1
Matrix decoder conforms to Dolby Digital EX
e)
5.1
—
c)
e)
DTS-ES Matrix 6.1
6.1
DTS Matrix decoder
DTS Discrete decoder
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “MATRIX”
Dolby Digital EX is applied to decode the surround back signal regardless of the 6.1 channel decode
a)
flag in the input stream. This decoder conforms to Dolby Digital EX and functions the same as the
f)
decoders used in movie theaters.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
e)
6.1
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
b)
e)
6.1
e)
6.1
c)
e)
DTS-ES Matrix 6.1
6.1
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “OFF”
Surround back decoding is not performed.
a)
6.1 channel decode flag is the information recorded in software like DVDs.
b)
Dolby Digital DVD that includes a Surround EX flag. The Dolby Corporation web page can help you distinguish
Surround EX films.
c)
d)
Software encoded with a flag to denote it has both Surround EX and 5.1 channel signals.
Software encoded with both 5.1 channel signals and an extension stream designed for returning those signals to
6.1 discrete channels. Discrete 6.1 channel signals are DVD specific signals not used in movie theaters.
When two surround back speakers are connected, the output channel will be 7.1 channels (except for STR-
DA3000ES models of area code CEL, TW).
e)
f)
This decoder can be used for all 6.1 formats (Dolby Digital EX, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1).
Note
There may be no sound from the surround back speaker in Dolby Digital EX mode. Some discs have no Dolby Digital
EX flag even though the packages have Dolby Digital EX logos. In this case, select “MATRIX”.
37GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectable audio inputs for each
input
Advanced Adjustments and Settings
VIDEO 3 OPT
VIDEO 3, VIDEO 1, VIDEO 2, TAPE
DVD COAX, DVD OPT
Assigning the audio input
— DIGITAL ASSIGN
DVD, VIDEO 1, VIDEO 2, TAPE
TV/SAT OPT
You can assign the digital audio input for other
input. This function is convenient in the
following cases.
TV/SAT, VIDEO 1, VIDEO 2, TAPE
MD/DAT OPT
MD/DAT, VIDEO 1, VIDEO 2, TAPE
CD/SACD COAX, CD/SACD OPT
CD/SACD, VIDEO 1, VIDEO 2, TAPE
(Example) When you have two DVD players
and no digital audio input jack is available
for the second DVD player.
Connect the first DVD player to the DVD
COAXIAL IN jack and connect the second
DVD player to the DVD OPTICAL IN jack.
Also, connect the analog audio/video output
jacks on the second DVD player to the VIDEO
2 INPUT jacks on the receiver.
Notes
• You cannot assign several audio inputs to the same
input.
• You cannot use the audio input for the original input
when it is assigned to another input.
• When you assign the audio input, the INPUT MODE
• You cannot assign for TUNER.
Assign “DVD COAX” to DVD and assign
“DVD OPT” to VIDEO 2.
1
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
Rotate MENU to select “DIGITAL
ASSIGN ?”.
3
4
Press MEMORY/ENTER.
Rotate MENU to select the digital audio
input you want to assign.
5
Rotate –/+ to select the input you want
to assign the digital audio input jack
selected in step 4.
The input you can assign varies for each
audio input. For details, see “Selectable
38GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the audio input
mode for digital
components
Customizing sound fields
By adjusting the SURR SET UP menu and
LEVEL menu, you can customize the sound
fields to suit your particular listening situation.
— INPUT MODE
Note on the displayed items
The setup items you can adjust in each menu
vary depending on the sound field. Certain setup
parameters may be dimmed in the display. This
means that the selected parameter is either
unavailable or fixed and unchangeable.
You can switch the audio input mode for
components for which this receiver have digital
audio input jacks.
1
2
Rotate INPUT SELECTOR to select the
input.
Press INPUT MODE repeatedly to
select the audio input mode.
Adjusting the SURR SET UP
menu
The selected audio input mode appears in
the display.
You can customize the surround effects of the
selected sound field. The settings are stored
individually for each sound field.
Audio input modes
• AUTO 2CH
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Gives priority to the analog audio signals
input to the AUDIO IN (L/R) jacks when
there is no digital audio signals.
• COAXIAL FIXED
2
3
Rotate MAIN MENU to select “SURR
SET UP”.
Specifies the digital audio signals input to the
DIGITAL COAXIAL input jack.
• OPTICAL FIXED
Rotate MENU to select the parameter.
For details, see “SURR SET UP menu
parameters” below.
Specifies the digital audio signals input to the
DIGITAL OPTICAL input jacks.
• ANALOG 2CH FIXED
4
5
While monitoring the sound, rotate –/+
to adjust the selected parameter.
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
parameters.
Notes
• You cannot select the digital audio input which is
assigned to another function by DIGITAL ASSIGN
SURR SET UP menu parameters
x EFFECT LEVEL XXX%
(Effect level)
• Some of the audio input modes do not appear
depending on the input.
Initial setting: 100%
Higher settings apply more surround effect. You can
adjust from 20 % to 120 % in 5 % steps.
For advanced SURR SET UP
menu adjustments
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON” to enable advanced
adjustments.
continued
39GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x MULTI CH 1 SW XXX dB
(Multi channel 1 sub woofer level)
Adjusting the LEVEL menu
x MULTI CH 2 SW XXX dB
(Multi channel 2 sub woofer level)
You can adjust the balance and level of each
speaker. These settings are applied to all sound
fields.
Initial setting: 0 dB
Lets you increase the level of the MULTI CHANNEL
INPUT 1/MULTI CHANNEL INPUT 2 sub woofer
channel by +10 dB. This adjustment may be necessary
when connecting a DVD player to the MULTI
CHANNEL INPUT 1/MULTI CHANNEL INPUT 2
jacks. The sub woofer level from DVD players is 10 dB
lower than Super Audio CD players.
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
2
3
Rotate MAIN MENU to select “LEVEL”.
Rotate MENU to select the parameter.
For details, see “LEVEL menu parameters”
below.
* Only when the surround back speaker is set to
“SINGLE” or “YES” in the SPEAKER SET UP
4
5
While monitoring the sound, rotate –/+
to adjust the selected parameter.
**Only when the surround back speaker is set to
“DUAL” in the SPEAKER SET UP menu (except for
STR-DA3000ES models of area code CEL, TW)
parameters.
Note
LEVEL menu parameters
When one of the following sound fields are selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” in the SPEAKER SET
UP menu. However, the sound will be output from the
sub woofer if the digital input signal contains LFE
(Low Frequency Effect) signals, or if the front or
surround speakers are set to “SMALL”.
– D.CONCERT HALL A
x TEST TONE (Test Tone)
Initial setting: OFF
Lets you output the test tone sequentially from each
speaker. When set to “AUTO”, the test tone is output
from each speaker automatically. When set to “FIX”,
you can select which speaker will output the test tone.
x FRONT L_I_R (Front speaker balance)
Initial setting: 0 (BALANCE)
– D.CONCERT HALL B
– CHURCH
Lets you adjust the balance between front left and right
speakers. You can adjust from –8 dB to +8 dB in 0.5
dB steps.
– JAZZ CLUB
– LIVE CONCERT
– STADIUM
x CENTER XXX.X dB
(Center speaker level)
– SPORTS
x SURROUND L XXX.X dB
(Surround speaker (L) level)
For advanced LEVEL menu
adjustments
x SURROUND R XXX.X dB
(Surround speaker (R) level)
Use the CUSTOMIZE menu and set “MENU
EXPAND” to “ON” to enable advanced
adjustments.
x SURR BACK XXX.X dB
(Surround back speaker level)*
For details on “MENU EXPAND”, see page 42.
x SURR BACK L XXX.X dB
(Surround back (L) level)**
x SURR BACK R XXX.X dB
(Surround back (R) level)**
Resetting sound fields to the
initial settings
x SUB WOOFER XXX.X dB
(Sub woofer level)
1
2
Press ?/1 to turn off the power.
Initial setting: 0 dB
You can adjust from –20 dB to +10 dB in 0.5 dB steps.
While holding down MUSIC, press
?/1.
40GB
Download from Www.Somanuals.com. All Manuals Search And Download.
“S.F. Initialize” appears in the display and
all sound fields are reset to the initial
setting.
Adjusting the equalizer
You can adjust the tonal quality (bass, treble
level) of each speaker using the EQUALIZER
menu.
Midrange
Bass
Treble
Level
(dB)
Frequency Frequency
(Hz) (Hz)
Frequency
(Hz)
You can store up to 5 different equalizer settings
in the equalizer bank (EQ PRESET [1]–[5]) and
apply them.
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
2
Rotate MAIN MENU to select
“EQUALIZER”.
3
4
Rotate MENU to select “EQ PRESET”.
Rotate –/+ to select the equalizer bank
you want to adjust (EQ PRESET [1] –
[5]).
5
Rotate MENU to select the parameter.
For details, see “EQUALIZER menu
parameters” below.
6
7
While monitoring the sound, rotate –/+
to adjust the selected parameter.
Repeat steps 5 and 6 to adjust the other
items.
EQUALIZER menu parameters
x EQ PRESET (Preset equalizer selection)
x FRONT BASS XXX dB
(Front speaker bass level)
x FRONT TREBLE XXX dB
(Front speaker treble level)
x CENTER BASS XXX dB
(Center speaker bass level)
x CENTER MID XXX dB
(Center speaker midrange level)
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 1 dB steps.
continued
41GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x CENTER MID XXX Hz
(Center speaker midrange frequency)
Advanced settings
Initial setting: 1 kHz
You can adjust from 100 Hz to 10 kHz in 5 steps (100
Hz, 300 Hz, 1 kHz, 3 kHz, 10 kHz).
Using the CUSTOMIZE menu
to adjust the receiver
x CENTER TREBLE XXX dB
(Center speaker treble level)
You can adjust various receiver settings using
the CUSTOMIZE menu.
x SURR/SB BASS XXX dB
(Surround/surround back speaker bass level)
x SURR/SB TRE. XXX dB
(Surround/surround back speaker treble level)
1
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
Initial setting: 0 dB
Rotate MENU to select the parameter.
You can adjust from –10 dB to +10 dB in 1 dB steps.
For details, see “CUSTOMIZE menu
parameters” below.
x PRESET X CLEAR
(Equalizer bank clear)
You can reset the adjusted equalizer settings to the
initial setting. For details, see “Clearing stored
3
4
Rotate –/+ to adjust the selected
parameter.
items.
Tip
You can adjust the front speaker bass and treble level
with BASS control and TREBLE control.
CUSTOMIZE menu parameters
The initial setting is underlined.
To apply the stored equalizer
x MENU EXPAND (Menu expanding)
1 Rotate MAIN MENU to select “EQUALIZER”
2 Rotate MENU to select “EQ PRESET”.
3 Rotate –/+ to select “EQ PRESET [1] – [5]”.
• ON
The advanced parameters for the SPEAKER SET
UP, SURR SET UP and LEVEL menus are displayed
and can be adjusted.
Clearing stored equalizer
settings
and the following pages.
• OFF
1
Rotate MAIN MENU to select
“EQUALIZER”.
The advanced parameters are not displayed.
x DTS 96/24 DEC. (DTS 96/24 decoding mode)
2
3
Rotate MENU to select “EQ PRESET”.
• AUTO
When a DTS 96/24 signal is input, it is played back
at 96 kHz sampling frequencies.
• OFF
Rotate +/– to select the equalizer (EQ
PRESET [1] – [5]) you want to clear.
4
Rotate MENU to select “PRESET X
CLEAR”.
Even when a DTS 96/24 signal is input, it is played
back at 48 kHz sampling frequencies.
“X” is the number of the selected equalizer
bank.
Note
This parameter is valid only in the A.F.D. mode
(page 33). In other sound fields, this parameter is
always set to “OFF”.
5
6
Rotate –/+ to select “YES”, then press
MEMORY/ENTER.
x SB DECODING
(Surround back decoding mode)
“Are you sure?” appears in the display.
Rotate –/+ to select “YES”, then press
MEMORY/ENTER.
You can use the CUSTOMIZE menu to set the
surround back decoding mode. See page 36.
• AUTO
• MATRIX
• OFF
“PRESET X CLEARED!” appears in the
display and the adjusted contents of the
selected equalizer bank are cleared.
42GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x LIP SYNC (Time alignment)
(STR-DA5000ES only)
which you use the 2 way remote control system.
Then set the 2 way remote control system for the
component to “ON”. For other components, set the 2
way remote control system to “OFF”.
Initial setting: 0 ms
Lets you delay the output of audio to adjust the gap
between video and audio. You can adjust from 0 ms to
200 ms in 10 ms steps.
x COLOR SYSTEM
(OSD color system)
(Models of area code CEL only)
x DC P.LINEARIZER (Phase Linearlizing)
Lets you select the color system.
Lets you change the phase polarity of low frequency
signals and enhance the bass.
• NTSC
• PAL
• OFF
x OSD H.POSITION
(OSD horizontal position)
The bass is not enhanced.
• STD
• MID
• HI
Initial setting: 4
Lets you adjust the position of the on-screen display
horizontally. You can adjust from 0 to 64.
The bandwidth range of the phase correction
increases in the order of “STD”, “MID”, “HI”.
x OSD V.POSITION
(OSD vertical position)
x S.FIELD LINK (Sound field link)
Initial setting: 4
• ON
Lets you adjust the position of the on-screen display
vertically. You can adjust from 0 to 32.
Lets you apply the last selected sound field to an
input whenever it is selected. For example, if you
select STADIUM for the CD/SACD input, then
change to a different input and return to CD/SACD,
STADIUM will automatically be applied again.
• OFF
x DIMMER (Brightness of the display)
Lets you adjust the brightness of the display in 3 steps.
For STR-DA3000ES, DIMMER indicator lights up.
When you set to turn off the display completely, the
MULTI CHANNEL DECODING indicator is also
turned off.
Sound field link is not activated.
x DEC. PRIORITY
(Digital audio input decoding priority)
x UP YUV HUE (Video hue level)
Initial setting: 4
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
Lets you adjust the hue of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 7.
The initial setting is “AUTO” for VIDEO 1, VIDEO 2,
VIDEO 3 and TV/SAT, and “PCM” for DVD, TAPE,
MD/DAT, CD/SACD, TUNER and PHONO. You can
use DECODE PRIORITY on the front panel.
• AUTO
x UP YUV SHARPNESS (Video sharpness level)
Initial setting: 4
Lets you adjust the sharpness of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 7.
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
• PCM
PCM signals are given priority (to prevent the
interruption when playback starts). Even when other
signals are input, the sound is output. When set to
“AUTO” and the sound from the digital audio jacks
(for CD, etc.) is interrupted when playback starts, set
to “PCM”.
x UP YUV COLOR (Video chroma level)
Initial setting: 4
Lets you adjust the chroma of the images when you
upconvert the video or S-video signals to component
video signals. You can adjust from 1 to 7.
x DIGITAL ASSIGN ?
(Digital audio input assignment)
x 2 WAY REMOTE
(2 way remote control system)
Lets you assign the digital audio input to other input.
For details, see “Assigning the audio input” on
• ON
Lets you turn on the 2 way remote control system.
Normally, select “ON”.
• OFF
x USER PRESET MEM.?
(User preset memory)
Lets you turn off the 2 way remote control system.
When you use another receiver, etc. that is also
compatible with the 2 way remote control system,
together with this receiver, select the component for
Lets you store the adjusted sound field settings, etc. For
continued
43GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x NAME IN?
x SP POSI.
(Naming inputs)
(Surround speaker position)*
Lets you set the name of inputs selected with INPUT
SELECTOR. For details, see “Naming preset stations
Lets you specify the location of your surround speakers
for proper implementation of the surround effects in
Advanced SPEAKER SET UP
menu parameters
120˚
100˚
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 19 for the SPEAKER SET UP menu
adjustments. Initial settings are underlined.
A
A
B
B
All SPEAKER SET UP menu
parameters
SP EASY SET UP
SPEAKER PATTERN
SUB WOOFER
D
D
C
FRONT SP
60
C
CENTER SP
30
SURROUND SP
SURR BACK SP
• SIDE/LOW
FRONT XXX meter (feet)*
CENTER XXX meter (feet)*
SURROUND XXX meter (feet)*
SURR BACK XXX meter (feet)*
SUB WOOFER XXX meter (feet)*
DISTANCE UNIT**
SP POSI.**
Select if the location of your surround speakers
corresponds to section A and C.
• SIDE/HIGH
Select if the location of your surround speakers
corresponds to section A and D.
• BEHD/LOW
Select if the location of your surround speakers
corresponds to section B and C.
• BEHD/HIGH
SP CROSSOVER > XXX Hz
Select if the location of your surround speakers
* Default unit is “feet” for models of area code U, CA.
corresponds to section B and D.
Default unit is “meter” for models of other area
* This setup item is not available when the surround
codes.
**Adjustable only when “MENU EXPAND” is set to
“ON”.
Tip
Surround speaker position is designed specifically for
implementation of the Cinema Studio EX modes.
For other sound fields, speaker position is not so
critical. Those sound fields were designed under the
premise that the surround speakers would be located
behind the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects becomes unclear unless set to “SIDE”.
x DISTANCE UNIT (Distance unit)
Lets you select the unit of measure for setting
distances.
• feet (default for models of area code U, CA)
The distance is displayed in feet.
• meter (default for models for models of other area
codes)
The distance is displayed in meters.
44GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Nevertheless, each listening environment has many
variables, like wall reflections, and you may obtain
better results using “BEHD” if your speakers are
located high above the listening position, even if they
are to the immediate left and right.
You can adjust the distribution of the center channel
signal, generated through the Dolby Pro Logic II
decoding, to the L/R speakers.
x DIMENSION F_I_S
(Dimension control)
Therefore, although it may result in a setting contrary
to the above explanation, we recommend that you
playback multi channel surround encoded software and
select the setting that provides a good sense of
spaciousness and that best succeeds in forming a
cohesive space between the surround sound from the
surround speakers and the sound of the front speakers.
If you are not sure which sounds best, select “BEHD”
and then use the speaker distance parameter and
speaker level adjustments to obtain proper balance.
Initial setting: midpoint (0)
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
You can adjust the difference between the front
channels and the surround channels.
x PANORAMA MODE
(Panorama mode)
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
x SP CROSSOVER > XXX Hz
(Speaker crossover frequency)
Initial setting: 100 Hz
Lets you set the bass crossover frequency of speakers
set to “SMALL” in the SPEAKER SET UP menu. You
can adjust from 40 Hz to 160 Hz in 10 Hz steps.
• ON
Lets you enjoy the surround sound by spreading the
sound field of front speakers to the left and right of
the listening position (panorama mode).
• OFF
Advanced SURR SET UP menu
parameters
Panorama mode is not activated.
x FRONT REVERB (Front reverberation)
This parameter is especially for “D.CONCERT HALL
amount of reverberations to add to the front signals
according to the original reverberations in the source.
• STD
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 39 for the SURR SET UP menu
adjustments. Initial settings are underlined.
Normally, select “STD”.
• WET
All SURR SET UP menu
parameters
Select to increase front reverberations.
EFFECT LEVEL
x SCREEN DEPTH (Screen depth)
Lets you create the sensation that the sound of the front
speakers comes from inside the screen in your listening
room, like theatres.
C. WIDTH L_C_R*
DIMENSION F_I_S*
PANORAMA MODE*
FRONT REVERB*
SCREEN DEPTH*
VIR.SPEAKERS*
A.F.D. 2CH SW*
• ON
Lets you create the sensation that the sound comes
from a very large screen with a great amount of
screen depth.
• OFF
This function is not activated.
Note
* Adjustable only when “MENU EXPAND” is set to
“ON”.
This parameter is only available for Cinema Studio EX
modes.
x C. WIDTH L_C_R
(Center width control)
x VIR.SPEAKERS (Virtual speakers)
This parameter is especially for the Cinema Studio EX
Initial setting: (3)
Lets you perform further adjustments for Dolby Pro
Logic II Music mode decoding. You can set this
parameter only when A.F.D. mode is set to “PRO
• ON
The virtual speakers are created.
continued
45GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• OFF
The virtual speakers are not created.
Lets you output the front 2 channel source sound
(instead of the test tone) sequentially from adjacent
speakers.
x A.F.D. 2CH SW
(Creating, low frequency signals)
x D.RANGE COMP.
(Dynamic range compressor)
• CREATE
Lets you compress the dynamic range of the sound
track. This may be useful when you want to watch
movies at low volumes late at night.
• OFF
Lets you create low frequency signals for output to
the subwoofer when “A.F.D. AUTO” is selected.
• OFF
Low frequency signals are not created.
The dynamic range is not compressed.
• STD
Advanced LEVEL menu
parameters
The dynamic range is compressed as intended by the
recording engineer.
• MAX
When “MENU EXPAND” is set to “ON”, all of
the following parameters are displayed and
adjustable.
See page 40 for the LEVEL menu adjustments.
Initial settings are underlined.
The dynamic range is compressed dramatically.
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the dynamic
range information included in the Dolby Digital signal.
“STD” is the standard setting, but it only enacts light
compression.
All LEVEL menu parameters
TEST TONE
Therefore, we recommend using the “MAX” setting.
This greatly compresses the dynamic range and lets
you view movies late at night at low volumes. Unlike
analog limiters, the levels are predetermined and
provide a very natural compression.
a)
PHASE NOISE
a)
PHASE AUDIO
FRONT L_I_R
CENTER XXX.X dB
SURROUND L XXX.X dB
SURROUND R XXX.X dB
Note
Dynamic range compression is possible with Dolby
Digital sources only.
b)
SURR BACK XXX.X dB
c)
SURR BACK L XXX.X dB
c)
SURR BACK R XXX.X dB
SUB WOOFER XXX.X dB
MULTI CH 1 SW XXX dB
MULTI CH 2 SW XXX dB
a)
D.RANGE COMP.
a)
Adjustable only when “MENU EXPAND” is set to
“ON”.
b)
When surround back speaker is set to “SINGLE” or
c)
When surround back speaker is set to “DUAL”
(except for STR-DA3000ES models of area code
CEL, TW) (page 20).
x PHASE NOISE (Phase noise)
Initial setting: OFF
Lets you output the test tone sequentially from adjacent
speakers.
x PHASE AUDIO (Phase audio)
Initial setting: OFF
46GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x 12V TRIG. MAIN
(12 V trigger for the main receiver)
Custom install mode
x 12V TRIG. 2ND
(12 V trigger for the 2nd zone)
(Models of area code U, CA only)
x 12V TRIG. 3RD
This receiver features the custom install modes
described below. Depending on how you intend
to use these features, use of these modes may
require additional equipment (available
separately) or modification of your listening
environment. Please consult the retailer where
you purchased this receiver for more
information.
(12 V trigger for the 3rd zone)
(STR-DA5000ES only)
Lets you turn on or off the external equipment by
outputting 12V triggers (STR-DA5000ES: 3 outputs,
STR-DA3000ES: 2 outputs) when the receiver is
turned on or off. For example, you can automatically
unroll your video screen when you turn on the receiver.
• OFF
Lets you turn off output of 12V triggers even when
the main receiver is turned on.
1
2
Rotate MAIN MENU to select “CIS”.
Rotate MENU to select the parameter.
• CTRL
Lets you turn on or off the output of 12V triggers
manually by the CIS command of the IR remote or
RS232C control.
For details, see “CIS menu parameters”
below.
• ZONE
3
4
Rotate –/+ to select the setting you
want.
Lets you turn on output of 12V triggers when the
main receiver or the receiver in each zone is turned
on.
items.
• INPUT (for “12V TRIG. MAIN” only)
Lets you turn on output of 12V triggers when the
main receiver is turned on, depending on the setting
of each input. See “To set the 12V trigger setting for
CIS menu parameters
Initial settings are underlined.
x 2ND ZONE (2nd zone source)
• MAIN (for “12V TRIG. 2ND” and “12V TRIG.
3RD” only)
x 3RD ZONE (3rd zone source)
(STR-DA5000ES only)
Lets you link 2nd or 3rd zone trigger operation to the
main receiver.
Lets you select the source signals (analog audio and
video signals for 2nd zone; only analog audio signals
for 3rd zone) you want to output in the 2nd zone or 3rd
zone (except PHONO). When you select “SOURCE”,
the signals of the current input is output.
To set the 12V trigger setting for
each input
The initial setting is “OFF” for all inputs. To set
this setting, you can use only the controls on the
front panel.
Tips
• Only signals from components connected to the
analog input jacks are output through the 2ND ZONE
or 3RD ZONE jacks. No signal is output from
components connected to only the digital input jacks.
• When “SOURCE” is selected, the signals input to the
MULTI CHANNEL INPUT jacks are not output
from the 2ND ZONE or 3RD ZONE jacks even when
MULTI CH IN function is used. The 2 channel
analog audio signals of the current input is output.
1 Select “INPUT” in “12V TRIG. MAIN”.
2 Press MEMORY/ENTER.
3 Rotate MENU to select the input.
4 Rotate –/+ to select “ON” to activate 12V
trigger or select “OFF” to disactivate.
5 Press MEMORY/ENTER.
x INSTALLER MODE (RS232C control)
• ON
The receiver can receive commands from the
RS232C port even when the power is off (standby
mode).
• OFF
The receiver does not receive commands from the
RS232C port when the power is off (standby mode).
47GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the USER PRESET
Storing the adjusted
settings
1
2
Press USER PRESET repeatedly to
select the USER PRESET you want.
Press MEMORY/ENTER.
— USER PRESET
Note
You can store the adjusted sound field settings,
etc. as USER PRESET up to 3 and can easily
apply.
When the DIGITAL ASSIGN setting is changed after
you store a USER PRESET and if the stored INPUT
MODE setting cannot be used, a selectable setting is
applied automatically.
Example:
Setting the USER PRESET
1) Use the DIGITAL ASSIGN function to assign
“DVD OPT” to “TAPE”.
1
Adjust the sound field, etc.
2) Set the INPUT MODE of TAPE to “AUTO 2CH” or
“OPTICAL FIXED”, then store in the USER
PRESET.
For the settings you can store, see “Settings
that can be stored in USER PRESET”.
3) Use the DIGITAL ASSIGN function to assign
“DVD OPT” to “DVD”.
2
3
4
Rotate MAIN MENU to select
“CUSTOMIZE”.
4) Select the USER PRESET stored in example 2).
The INPUT MODE of TAPE is automatically set to
“ANALOG 2CH FIXED”. You cannot select
“AUTO 2CH” or “OPTICAL FIXED”.
Rotate MENU to select “USER PRESET
MEM.?”.
Rotate –/+ to select the USER PRESET
number.
5
6
Press MEMORY/ENTER.
To store other settings, repeat steps 1
to 5.
Settings that can be stored in
USER PRESET
• Input selected by the INPUT SELECTOR
• INPUT MODE setting
• Selected sound field
• MULTI CH IN setting
• DIRECT setting
• NIGHT MODE setting
• C.WIDTH setting
• DIMENSION setting
• PANORAMA MODE setting
• EFFECT LEVEL setting
• FRONT REVERB setting
• SCREEN DEPTH setting
• VIR.SPEAKERS setting
• Tuner settings (band, frequency, stereo/mono
setting, preset number)
48GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
• You can select the character type as follows by
rotating –/+.
Alphabet (upper case) t Numbers t Symbols
• To enter a blank space, rotate –/+ until a blank
space appears in the display.
Other Operations
Naming preset stations
and inputs
• If you made a mistake, rotate MENU until the
character you want to change flashes, then rotate
–/+ to select the correct character.
You can enter a name of up to 8 characters for
preset stations and inputs selected with INPUT
SELECTOR, and display it in the receiver’s
display.
2
Press MEMORY/ENTER.
The entered name is registered.
Note (Models of area code CEL only)
When you name an RDS station and tune in the station,
the Program Service (PS) name appears instead of the
name you entered. (You cannot change the name of a
Program Service (PS) name. The name you entered
will be overwritten by the Program Service (PS)
name.)
To index a preset station
1
Rotate INPUT SELECTOR to select
tuner (“FM” or “AM”).
2
3
Press FM/AM to select “FM” or “AM”.
Tune in the preset station you want to
4
5
6
Rotate MAIN MENU to select “TUNER”.
Rotate MENU to select “NAME IN”.
Press MEMORY/ENTER.
The cursor flashes and you can select a
character. Follow the procedure of “To
To index an input
1
Rotate INPUT SELECTOR to select an
input you want to create an index name
for.
2
Rotate MAIN MENU to select
“CUSTOMIZE”.
3
4
Rotate MENU to select “NAME IN?”.
Press MEMORY/ENTER.
The cursor flashes and you can select a
character. Follow the procedure of “To
To create an index name
1
Use MENU and –/+ to create an index
name.
Rotate –/+ to select a character, then rotate
MENU to move the cursor to the next
position.
49GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
Selecting the speaker
system
You can set the receiver to turn off automatically
at a specified time by using the remote.
For details, refer to the operating instructions
supplied with the remote.
Set the SPEAKERS switch according to the
front speakers you want to drive.
Set to
To select
RM-LJ312:
A
The speakers connected to the FRONT
SPEAKERS A terminals.
Select SLEEP from the RECEIVER menu,
then press the key repeatedly while the
power is on.
B
The speakers connected to the FRONT
SPEAKERS B terminals.
RM-LG112:
A+B
The speakers connected to both the
FRONT SPEAKERS A and B terminals
(parallel connection).
Press ALT, then press SLEEP repeatedly
while the power is on.
OFF
No speaker output.
Each time you select or press SLEEP, the
display changes cyclically as follows:
2:00:00 t 1:30:00 t 1:00:00 t 0:30:00 t
OFF
While using Sleep Timer, “SLEEP” lights up in
the display.
Tip
To check the remaining time before the receiver turns
off, select SLEEP from the RECEIVER menu (RM-
LJ312) or press ALT, then press SLEEP (RM-LG112).
The remaining time appears in the display.
50GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Prepare the component for playing.
Recording
For example, insert the laser disc you want
to record into the LD player.
Before you begin, make sure you have
connected all components properly.
3
4
Insert a blank video tape into the VCR
(VIDEO 1 or VIDEO 2) for recording.
Start recording on the recording VCR,
then start playing the video tape or
laser disc you want to record.
Recording on an audio tape or
MiniDisc
Notes
You can record on a MiniDisc or cassette tape
using the receiver. See the operating instructions
of your cassette deck or MD deck if you need
help.
• You cannot record a digital audio signal using a
component connected to the analog VIDEO 1 OUT
or VIDEO 2 OUT jacks.
• Make sure to make both digital and analog
connections to the TV/SAT or DVD inputs. Analog
recording is not possible if you make only digital
connections.
1
2
Select the component to be recorded.
Prepare the component for playing.
For example, insert a CD into the CD
player.
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to record
from the sources.
3
4
Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
• The analog audio signals of the current input are
output from the VIDEO 1 OUT or VIDEO 2 OUT
jacks.
Start recording on the recording deck,
then start playback on the playback
component.
• The signals input to the MULTI CHANNEL INPUT
jacks are not output from VIDEO 1 OUT or VIDEO
2 OUT jacks even when MULTI CH IN is being
used. The analog audio signals of the current or
previously used input are output.
Notes
• You cannot record a digital audio signal using a
component connected to the analog TAPE OUT or
MD/DAT OUT jacks. To record a digital audio
signal, connect a digital component to the MD/DAT
OPTICAL OUT jacks.
• Sound adjustments do not affect the signal output
from the TAPE OUT or MD/DAT OUT jacks.
• The analog audio signals of the current input is
output from the TAPE OUT or MD/DAT OUT jacks.
• The signals input to the MULTI CHANNEL INPUT
jacks are not output from the TAPE OUT or MD/
DAT OUT jacks even when MULTI CH IN is being
used. The analog audio signals of the current or
previously used input are output.
Recording on a video tape
You can record from a VCR, a TV, or an LD
player using the receiver. You can also add
audio from a variety of audio sources when
editing a video tape. See the operating
instructions of your VCR if you need help.
1
Select the program source to be
recorded.
51GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the sound in another zone
(Models of area code U, CA only)
2ND ZONE OUT
S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO S2 VIDEO
OUT
OUT
IN
OUT
IN
OUT
IN
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
VARIABLE VARIABLE
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AC OUTLET
2ND
ZONE
3RD
ZONE
DVD
VIDEO 2
VIDEO 1
R
R
L
A
L
B
FRONT SPEAKERS
3RD ZONE OUT
(STR-DA5000ES only)
You can select analog audio/video signals for
output to the 2nd zone or audio signals for the
3rd zone (STR-DA5000ES only). For details on
signals are output. When you select
“SOURCE”, the signals of the current input
are output.
5
Press MASTER VOL +/– on the remote
to adjust the volume of the 2nd zone or
3rd zone.
Use the remote RM-US106 for the operation.
1
On the remote, press 2ND ZONE or 3RD
ZONE (STR-DA5000ES only).
The default setting of the volume is –∞ dB
(no sound output).
The remote switches to the 2nd zone or 3rd
zone (STR-DA5000ES only) mode. For
details on the supplied remote, refer to the
operating instructions supplied with the
remote.
Tips
• Even when this receiver is turned off, the receiver in
the 2nd zone or 3rd zone remains turned on. To turn
off all receivers, press ?/1 and AV ?/1 on the
remote at the same time (SYSTEM STANDBY).
• Only signals from components connected to the
analog input jacks are output through the 2ND ZONE
OUT or 3RD ZONE OUT (STR-DA5000ES only)
jacks. No signals are output from components
connected to only the digital input jacks.
2
3
4
Turn on the main receiver (this
receiver).
Turn on the amplifier in the 2nd or 3rd
zone.
Press one of the input buttons on the
remote to select the source signals you
want to output.
• When “SOURCE” is selected, the signals input to the
MULTI CH IN jacks are not output from the 2ND
ZONE OUT or 3RD ZONE OUT (STR-DA5000ES
only) jacks even when MULTI CH IN is selected.
The analog audio signals of the current function are
output.
For the 2nd zone, analog video and audio
signals are output. For the 3rd zone (STR-
DA5000ES only), only analog audio
52GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2nd zone connections
Main receiver
2nd zone
Monitor
Audio/video components
Speaker
Speaker
2ND
ZONE
OUT
Amplifier/Receiver
STR-DA5000ES
STR-DA3000ES
3rd zone connections
Main receiver
3rd zone
Audio components
Speaker
Speaker
3RD
ZONE
OUT
Amplifier/Receiver
STR-DA5000ES
53GB
Download from Www.Somanuals.com. All Manuals Search And Download.
If, however, you have a Sony CD changer with
VIDEO OUT jacks, set the command mode to
“CD 2” and connect the changer to the VIDEO
2 jacks on the amplifier (receiver).
CONTROL A1II Control
System
Connections
The CONTROL A1II Control System was
designed to simplify the operation of audio
systems composed of separate Sony
components. CONTROL A1II connections
provide a path for the transmission of control
signals which enable automatic operation and
control features usually associated with
integrated systems.
Currently, CONTROL A1II connections
between a Sony CD player, amplifier (receiver),
MD deck and cassette deck provide automatic
function selection.
You can connect up to 10 CONTROL A1II
compatible components in any order. However,
you can connect only one of each type of
component (i.e., 1 CD player, 1 MD deck, 1 tape
deck and 1 receiver).
(You may be able to connect more than one CD
player or MD deck, depending on the model.
Refer to the operating instructions supplied with
the respective component for details.)
Example
Note
Do not operate a 2 way remote control unit when the
CONTROL A1II jacks are connected via a PC
interface kit to a personal computer running “MD
Editor” or similar application. Also, do not operate the
connected component in a manner contrary to the
functions of the application, as this may cause the
application to operate incorrectly.
MD
deck
Tape
deck
CD
player
Other
components
Amplifier
(Reciever)
In the CONTROL A1II control system, the
control signals flow both ways, so there is no
distinction of IN and OUT jacks. If a component
has more than one CONTROL A1II jack, you
can use either one, or connect different
components to each jack.
Some CONTROL A1 compatible components
are supplied with a connecting cord as an
accessory. In this case, use the connecting cord
for your connection.
CONTROL A1II and CONTROL A1
compatibility
The CONTROL A1 control system has been updated
to the CONTROL A1II which is the standard system in
the Sony 300 disc CD changer and other recent Sony
components. Components with CONTROL A1 jacks
are compatible with components with CONTROL
A1II, and can be connected to each other. Basically,
the majority of the functions available with the
CONTROL A1 control system will be available with
the CONTROL A1II control system.
When using a commercially available cord, use
a monaural (2P) mini-plug cord less than 2
meters long, with no resistance.
However, when making connections between
components with CONTROL A1 jacks and
Basic Functions
components with CONTROL A1II jacks, the number
of functions that can be controlled may be limited
depending on the component. For detailed information,
refer to the operating instructions supplied with the
component(s).
The input selector on the receiver automatically
switches to the correct input when you press the
play button on one of the connected components
(Auto input selection).
The CONTROL A1II functions will operate as
long as the component you want to operate is
turned on, even if all of the other connected
components are not turned on.
If you have a Sony CD changer with a
COMMAND MODE selector
If your CD changer’s COMMAND MODE
selector can be set to CD 1, CD 2, or CD 3, be
sure to set the command mode to “CD 1” and
connect the changer to the CD jacks on the
amplifier (receiver).
Note
When recording, do not play any components other
than the recording source. It will cause the automatic
input selection to operate.
54GB
Download from Www.Somanuals.com. All Manuals Search And Download.
If you connect the CTRL S IN jack on
another component to the CTRL S OUT jack
on this unit
Using CONTROL S Control
System
Example
(Models of area code U, CA only)
IN OUT
IN OUT
IN
If you have a CONTROL S-compatible Sony
TV, satellite tuner, monitor, DVD player or
VCR, use a control S connecting cord (not
supplied) to connect the CTRL S IN (for TV,
satellite tuner, or monitor) or CTRL S OUT (for
VCR, etc.) jack on the receiver to the
TV
Tuner
VCR
OUT
Receiver
appropriate CONTROL S jack on the respective
component. Refer to the operating instructions
supplied with your TV, satellite tuner, monitor,
VCR, etc., for details.
I
i
.
H
>
m
M
x
X
If you connect the CTRL S OUT jack on
another component to the CTRL S IN jack
on this unit
+
–
O
+
–
+
–
Remote
Example
TV,VCR,
tuner,
monitor,
etc.
The remote sensor on this unit receives remote
codes the same way as the remote sensor on the
CTRL S IN component. This is useful if you
place the other component away from this unit.
OUT
IN
Receiver
I
i
.
H
>
m
M
x
X
+
–
+
–
+
–
Remote
The remote sensor on the CTRL S OUT
component receives remote codes the same way
as the remote sensor on this unit. This is useful
if you have placed this unit in a rack, etc.
55GB
Download from Www.Somanuals.com. All Manuals Search And Download.
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
Additional Information
Precautions
On safety
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
On power sources
• Before operating the unit, check that the operating
voltage is identical with your local power supply.
The operating voltage is indicated on the nameplate
at the rear of the receiver.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• If you are not going to use the receiver for a long
time, be sure to disconnect the receiver from the wall
outlet. To disconnect the AC power cord, grasp the
plug itself; never pull the cord.
• (Models of area code U, CA only)
One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet only
one way. If you are unable to insert the plug fully into
the outlet, contact your dealer.
• AC power cord must be changed only at the qualified
service shop.
On heat buildup
Although the unit heats up during operation, this is not
a malfunction. If you continuously use this unit at a
large volume, the cabinet temperature of the top, side
and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the receiver.
• Do not place the receiver near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
On operation
Before connecting other components, be sure to turn
off and unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
56GB
Download from Www.Somanuals.com. All Manuals Search And Download.
• Check that you have selected the correct
component with INPUT SELECTOR.
• Check that the SPEAKERS is not set to “OFF”
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
• When only a very low-level sound is heard, check
to see if NIGHT MODE is activated (page 36).
• The protective device on the receiver has been
activated. Turn off the receiver, eliminate the
short-circuit problem and turn on the power again.
There is no sound no matter which component
is selected.
• Check that both the receiver and all components
are turned on.
There is no sound from analog 2 channel
sources.
• Check that the MASTER VOLUME control is not
set at –∞ dB.
• Check that the SPEAKERS is not set to “OFF”
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
• Check that the INPUT MODE is not set to
“COAXIAL FIXED” nor “OPTICAL FIXED” for
• Check that all speaker cords are connected
correctly.
• Press MUTING on the remote to cancel the
muting function.
• Check that the MULTI CH IN function is selected.
There is no sound from digital sources (from
COAXIAL or OPTICAL input jack).
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
• Check that the INPUT MODE is not set to
the INPUT MODE is not set to “COAXIAL
FIXED” for the sources from OPTICAL input
jack, nor set to “OPTICAL FIXED” for the
sources from COAXIAL input jack.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the receiver correctly.
Check the connection of the front speaker which is
not outputting any sound.
• Check that the MULTI CH IN function is selected.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
• Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
• Make sure you have not connected only the L or R
jack to a monaural component. Use a monaural-
stereo cable (not supplied) and connect it to both
the L and R jacks. However, there will be no
sound from the center speaker when a sound field
(PRO LOGIC, etc.) is selected. When the center
speaker is set to “NO”, sound is output only from
front L/R speakers.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters away
from a TV set or fluorescent light.
• Move your TV away from the audio components.
• Make sure you have grounded U SIGNAL GND
terminal (only when a turntable is connected).
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no sound or only a very low-level
sound is heard.
• Check that the speakers and components are
connected securely.
continued
57GB
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound from the center speaker.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
• Select the CINEMA STUDIO EX mode
• Make sure the center speaker is set to either
Outdoor FM antenna
There is no sound from the surround back
speakers.
Receiver
• Some discs have no Dolby Digital EX flag even
though the packages have Dolby Digital EX
FM
AM
U
75 COAXIAL
There is no sound or only a very low-level
sound is heard from the surround/surround
back speakers.
ANTENNA
Ground wire
(not supplied)
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
To ground
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
• Make sure the surround speakers are set to either
• Make sure the surround back speaker is set to
either “DUAL” or “SINGLE” (except for STR-
DA3000ES models of area code CEL, TW), or
“YES” (STR-DA3000ES models of area code
CEL, TW only).
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
• Press DISPLAY so that the frequency appears in
the display.
There is no sound from sub woofer.
• When all speakers are set to “LARGE” and
“Neo:6 Cinema” or “Neo:6 Music” is selected,
there is no sound from the sub woofer.
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
RDS does not work.*
• Make sure that you’re tuned to an FM RDS
station.
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
• Select a stronger FM station.
Dolby Digital or DTS multi channel sound is
not reproduced.
The RDS information that you want does not
appear.*
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• Contact the radio station and find out whether or
not they actually provide the service in question.
If so, the service may be temporarily out of order.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the receiver.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
• Connect your TV to the receiver using the same
type of connecting cord as the one used to connect
12).
Recording cannot be done.
• Check that the components are connected
correctly.
• Select the source component with INPUT
SELECTOR.
58GB
Download from Www.Somanuals.com. All Manuals Search And Download.
receiver, leave the receiver for a while and turn on
the power again.
Remote control
The remote does not function.
PROTECTOR/CHECK CODE 21
Turn off the receiver and consult your nearest Sony
dealer.
• Point the remote at the remote sensor on the
receiver.
• Remove any obstacles in the path between the
remote and the receiver.
PROTECTOR/CHECK CODE 22
There is a problem with the power circuit. Turn off
the receiver and check the speaker connection. Then
turn on the power again.
• Replace all the batteries in the remote with new
ones, if they are weak.
• Check if the command modes of the receiver and
the remote is the same. If the command mode of
the receiver and the remote is different, you
cannot operate the receiver with the remote.
To switch the command mode of the remote, press
?/1 while pressing INPUT MODE. Each time
you press ?/1, the command mode switches
between “COMAMND MODE [AV2]” and
“COMAMND MODE [AV1]”. (The initial setting
is “COMAMND MODE [AV2]”.) For STR-
DA5000ES, the command mode of the remote is
automatically set to match the receiver when you
perform the AMP REGIST operation again.
• Make sure you select the correct input on the
remote.
Reference sections for clearing
the memory
To clear
See
All memorized settings
Customized sound fields
* Models of area code CEL only.
Error messages
If there is a malfunction, the display shows a
code of two numbers and a message. You can
check the condition of the system by the
message. Refer to the following table to solve
the problem. If any problem persists, consult
your nearest Sony dealer.
DECODE ERROR/CHECK CODE 01
Appears when the signal which the receiver cannot
decode (ex. DTS-CD) is input when “DEC.
PRIORITY” in the CUSTOMIZE menu is set to
“PCM”. Set to “AUTO”.
PROTECTOR/CHECK CODE 11
Irregular current is output from the speakers. Turn
off the receiver, check the speaker connection and
turn on the power again.
PROTECTOR/CHECK CODE 12
The amplifier section is overheated. Check that the
ventilation hole is not covered. Turn off the
receiver, leave the receiver for a while and turn on
the power again.
PROTECTOR/CHECK CODE 13
The power section is overheated. Check that the
ventilation hole is not covered. Turn off the
59GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2)3)
SURR BACK : 130 W +
130 W
SURR BACK : 130 W
Actual Rated Maximum Output at Stereo Mode
Specifications
2)4)
1)4)
AUDIO POWER SPECIFICATIONS
(8 ohms, JEITA)
STR-DA5000ES:
Actual Rated Maximum Output at Surround Mode
220 W + 220 W
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
4)
(Models of area code U only)
(8 ohms, JEITA)
2)
STR-DA5000ES:
FRONT : 220 W + 220 W
STR-DA5000ES:
2)
CENTER : 220 W
With 8 ohm loads, both channels driven, from 20
– 20,000 Hz; rated 170 watts per channel
minimum RMS power, with no more than 0.6%
total harmonic distortion from 250 milliwatts to
rated output.
2)
SURR : 220 W + 220 W
2)
SURR BACK : 220 W + 220
W
Models of area code CEL, CN, KR:
POWER OUTPUT
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
STR-DA5000ES:
STR-DA3000ES:
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD 0.7%)
STR-DA3000ES:
1)
With 8 ohm loads, both channels driven, from 20
– 20,000 Hz; rated 150 watts per channel
minimum RMS power, with no more than 0.6%
total harmonic distortion from 250 milliwatts to
rated output.
170 W + 170 W
150 W + 150 W
Amplifier section
Models of area code U, CA, TW:
POWER OUTPUT
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.6%)
STR-DA5000ES:
STR-DA3000ES:
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
150 W + 150 W
130 W + 130 W
1)
2)
STR-DA5000ES:
FRONT : 170 W + 170 W
2)
CENTER : 170 W
STR-DA5000ES:
STR-DA3000ES:
170 W + 170 W
150 W + 150 W
2)
SURR : 170 W + 170 W
2)
SURR BACK : 170 W + 170
Reference Power Output at Stereo Mode
(4 ohms 20 Hz – 20 kHz, THD 0.6%)
W
2)
STR-DA3000ES:
FRONT : 150 W + 150 W
CENTER : 150 W
SURR : 150 W + 150 W
SURR BACK : 150 W
STR-DA5000ES:
STR-DA3000ES:
150 W + 150 W
130 W + 130 W
2)
2)
Reference Power Output
(8 ohms 20 Hz – 20 kHz, THD 0.6%)
2)
2)
(4 ohms 1 kHz, THD 0.7%)
STR-DA5000ES:
STR-DA5000ES:
FRONT : 170 W + 170 W
2)
2)
FRONT : 150 W + 150 W
CENTER : 170 W
SURR : 170 W + 170 W
SURR BACK : 170 W + 170
W
2)
2)
CENTER : 150 W
2)
2)
SURR : 150 W + 150 W
2)
SURR BACK : 150 W + 150
2)
W
STR-DA3000ES:
FRONT : 150 W + 150 W
2)
2)
STR-DA3000ES:
FRONT : 130 W + 130 W
CENTER : 130 W
SURR : 130 W + 130 W
SURR BACK : 130 W
CENTER : 150 W
SURR : 150 W + 150 W
SURR BACK : 150 W +
150 W
2)
2)
2)
2)3)
2)
1)
2)4)
Actual Rated Maximum Output at Stereo Mode
(8 ohms, JEITA)
STR-DA5000ES:
STR-DA3000ES:
SURR BACK : 150 W
(4 ohms 20 Hz – 20 kHz, THD 0.6%)
2)
220 W + 220 W
200 W + 200 W
STR-DA5000ES:
FRONT : 150 W + 150 W
2)
CENTER : 150 W
SURR : 150 W + 150 W
SURR BACK : 150 W + 150
W
2)
Actual Rated Maximum Output at Surround Mode
2)
(8 ohms, JEITA)
2)
STR-DA5000ES:
FRONT : 220 W + 220 W
2)
2)
CENTER : 220 W
STR-DA3000ES:
FRONT : 130 W + 130 W
2)
2)
SURR : 220 W + 220 W
CENTER : 130 W
SURR : 130 W + 130 W
2)
2)
SURR BACK : 220 W + 220
W
60GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2)
STR-DA3000ES:
FRONT : 200 W + 200 W
Outputs
2)
CENTER : 200 W
TAPE, MD/DAT
(REC OUT), VIDEO
1, 2 (AUDIO OUT)
2)
SURR : 200 W + 200 W
SURR BACK : 200 W + 200
2)
W
FRONT L/R,
CENTER,
1) Depending on the sound field settings and the
source, there may be no sound output.
SURROUND L/R,
SURROUND BACK
(L/R), SUB WOOFER
2) Measured under the following conditions:
Area code
U, CA
TW
Power requirements
120 V AC, 60 Hz
EQUALIZER
Gain levels
110 V AC, 60 Hz
±10 dB, 1 dB step
CEL
230 V AC, 50/60 Hz
220-230 V AC, 50/60 Hz
220 V AC, 60 Hz
FM tuner section
CN
Tuning range
Antenna
Antenna terminals
Sensitivity
Mono:
Stereo:
Useable sensitivity
S/N
87.5 - 108.0 MHz
FM wire antenna
75 ohms, unbalanced
KR
3) Models of area code U, CA only.
4) Models of area code TW only.
18.3 dBf, 2.2 µV/75 ohms
38.3 dBf, 22.5 µV/75 ohms
11.2 dBf, 1 µV/75 ohms
Frequency response
PHONO
RIAA equalization curve
±0.5 dB
Mono:
Stereo:
76 dB
70 dB
MULTI CHANNEL
INPUT 1, 2, CD/
10 Hz – 40 kHz
Harmonic distortion at 1 kHz
Mono:
Stereo:
±3 dB (when sound field and
equalizer bypassed)
0.3%
0.5%
SACD, TAPE, MD/
DAT, DVD, TV/SAT,
VIDEO 1, 2, 3
Separation
Frequency response
45 dB at 1 kHz
30 Hz – 15 kHz,
+0.5/–2 dB
60 dB at 400 kHz
Inputs (Analog)
PHONO
Selectivity
S/N: 86 dB
S/N: 96 dB
AM tuner section
Tuning range
Models of area code U, CA:
530 – 1,710 kHz
MULTI CHANNEL
INPUT 1, 2, CD/
5)
SACD, TAPE, MD/
DAT, DVD, TV/SAT,
VIDEO 1, 2, 3
(With 10-kHz tuning scale)
531 – 1,710 kHz
(With 9-kHz tuning scale)
5)
Models of other area codes:
531 – 1,602 kHz
(With 9-kHz tuning scale)
Loop antenna
Antenna
Inputs (Digital)
Usable sensitivity
50 dB/m (at 1,000 kHz or 999
kHz)
54 dB (at 50 mV/m)
0.5% (50 mV/m, 400 Hz)
CD/SACD, DVD
(Coaxial)
S/N: 96 dB
(A, 20 kHz LPF)
S/N
Harmonic distortion
Selectivity
At 9 kHz:
CD/SACD, DVD, TV/ S/N: 96 dB
SAT, MD/DAT,
VIDEO3 (Optical)
35 dB
40 dB
(A, 20 kHz LPF)
At 10 kHz:
5) You can change the AM tuning scale to 9 kHz or 10
kHz. After tuning in any AM station, turn off the
continued
61GB
Download from Www.Somanuals.com. All Manuals Search And Download.
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
AC power cord (1)
STR-DA5000ES:
Video section
Inputs/Outputs
Video:
S-video:
Remote commander RM-LJ312 (1)
R6 (size-AA) batteries (3)
STR-DA3000ES:
Remote commander RM-LG112 (1)
R6 (size-AA) batteries (2)
Models of area code U, CA:
Remote commander RM-US106 (1)
R6 (size-AA) batteries (2)
1 Vp-p, 75 ohms
Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms
P /C /B-Y: 0.7 Vp-p, 75
B
B
ohms
P /C /R-Y: 0.7 Vp-p, 75
R
R
ohms
For details on the area code of the component you
are using, see page 3.
80 MHz HD Pass Through
General
Power requirements
Design and specifications are subject to change
without notice.
Area code
U, CA
CEL
Power requirements
120 V AC, 60 Hz
230 V AC, 50/60 Hz
110 V AC, 60 Hz
TW
CN
220-230 V AC, 50/60 Hz
220 V AC, 60 Hz
KR
Power consumption
STR-DA5000ES:
Area code
U, CEL, TW, CN
CA
Power consumption
300 W
500 VA
STR-DA3000ES:
Area code
Power consumption
U, CEL, TW, CN, KR 280 W
CA 470 VA
Power consumption (during standby mode)
1 W
AC outlets
Area code
U, CA
AC outlets
2 switched, 120 W/1A MAX
1 switched, 100 W MAX
– (no AC outlet)
CEL
CN, KR, TW
Dimensions
430 × 175 × 470 mm
including projecting parts and
controls
Mass (Approx.)
13 kg
62GB
Download from Www.Somanuals.com. All Manuals Search And Download.
63GB
Download from Www.Somanuals.com. All Manuals Search And Download.
List of button locations and reference pages
Illustration number
How to use this page
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
R
R
Name of button/part Reference page
Main unit
ALPHABETICAL ORDER
NUMBERS AND SYMBOLS
?/1 (power) 1
Digital Cinema Sound indicator
4
DIMMER indicator (STR-
DA3000ES only) qd
DIRECT indicator 2
Input indicators (STR-DA5000ES
only) qd
IR receptor qf
49)
MULTI CHANNEL DECODING
indicator qs
PHONES jack qg
SURR BACK DECODING wh
64GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
qf
qs
qa
0
9
qd (STR-DA5000ES)
(STR-DA3000ES)
qd
v
qg qh
qj qk ql w; wa ws wd wf wg wh
es ea e; wl wk
wj
65GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
P
Adjusting
CIS parameters 47
Preset stations
how to 27
CUSTOMIZE parameters
42
how to tune 27
EQUALIZER parameter 41
LEVEL parameter 40, 46
SPEAKER SET UP param-
eters 19, 44
R
RDS 28
Recording
on a video tape 51
on an audio tape or MD 51
speaker volume 22
SURR SET UP parameters
39
Automatic tuning 25
S
Selecting
component 24
C
front speaker system 50
sound field 34–35
Changing
display 30
effect level 39
Sleep Timer 50
Sound field
customizing 39
CIS 47
CIS menu 47
pre-programmed 34–35
Clearing receiver’s memory 18
CONTROL A1 II 54
Crossover frequency 45
CUSTOMIZE menu 42
resetting 40
selecting 34–35
SPEAKER SET UP menu 19,
44
Speakers
D
adjusting speaker volume
22
connection 16
Digital Cinema Sound 34
Direct tuning 26
Dubbing. See Recording
impedance 17
placement 16
Supplied accessories 62
SURR SET UP menu 39, 45
E
Editing. See Recording
Effect level 39
T
EQUALIZER menu 41
Test tone 22
TUNER menu 25, 49
I
Tuning
Indexing. See Naming
automatically 25
directly 26
preset stations 27
L
Labeling. See Naming
LEVEL menu 46
N
Naming 49
66GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|