3-863-987-11 (1)
Network Camera
User’s Guide
Software Version 1.0
SNC-DF70N/DF70P
© 2004 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have any questions about this product, you may
call:
NOTICE TO USERS
© 2004 Sony Corporation. All rights reserved. This
manual or the software described herein, in whole or in
part, may not be reproduced, translated or reduced to
any machine readable form without prior written
approval from Sony Corporation.
Sony's Business Information Center (BIC) at
1-800-686-SONY (7669)
or Write to: Sony Customer Information Services
Center
6900-29, Daniels Parkway, PMB 330
Fort Myers, Florida 33912
SONY CORPORATION PROVIDES NO
WARRANTY WITH REGARD TO THIS MANUAL,
THE SOFTWARE OR OTHER INFORMATION
CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS
MANUAL, THE SOFTWARE OR SUCH OTHER
INFORMATION. IN NO EVENT SHALL SONY
CORPORATION BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF
OR IN CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION
Declaration of Conformity
Trade Name:
Model No:
SONY
SNC-DF70N
Responsible Party: Sony Electronics Inc.
Address:
16450 W. Bernardo Dr, San
Diego, CA 92127 U.S.A.
858-942-2230
Telephone No:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CONTAINED HEREIN OR THE USE THEREOF.
Sony Corporation reserves the right to make any
modification to this manual or the information contained
herein at any time without notice.
The software described herein may also be governed by
the terms of a separate user license agreement.
Microsoft, Windows, Internet Explorer and MS-DOS
are registered trademarks of Microsoft Corporation in
the United States and/or other countries.
Java is a trademark of Sun Microsystems, Inc. in the
United States and other countries.
Intel and Pentium are registered trademarks of Intel
Corporation or its subsidiaries in the United States and
other countries.
All other company and product names are trademarks or
registered trademarks of the respective companies or
their respective makers.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the System
Table of Contents
Setting the Camera Image and Audio
Configuring the Network — Network setting
Dynamic IP address notification Tab — Notifying
Assigning the IP Address Using the Setup
Sending an Image via mail
Alarm sending Tab — Setting the mail sending
Periodical sending Tab — Setting the periodical
Displaying the setting window for the
Sending Images to FTP Server
Common Tab
Alarm sending Tab — Setting the FTP client
Periodical sending Tab — Setting the Periodical
Recording a Still Image in the Built-in Memory of
Recording Images in Memory
Common Tab — Setting the Image memory
Alarm recording Tab — Setting the Image
Periodical recording Tab — Setting the Periodical
Downloading Images from the Camera
Setting the Alarm Output
Setting the Operations from the Viewer Page
4
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Schedule
5
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Overview
• Corresponding to PoE (Power of Ethernet).
• The camera is supplied with the IP Setup Program for
easy performance of the network setting.
Features
•Microsoft, Windows, Internet Explorer and MS-DOS are
registered trademarks of Microsoft Corporation in the
United States and/or other countries.
This is dome-shaped color video camera for which
®
•Super HAD CCD® is a registered trademark of Sony
Corporation.
the 1/4 type Super HAD CCD is adopted. It has the
following features.
•IP66 is a protection grade provided under JIS and IEC.
Camera section
• Day/Night function automatically switches between
color and monochrome modes. You can control this
function through an external source also.
• Includes the Vari-focal auto iris lens as the standard
equipment. The focal length of the lens is from 3.0
mm to 8.0 mm.
• The best picture quality is available in the lowest light
degree (0.9 lux) to the object (in the color mode).
• High quality CCD and the clear dome cover enable to
get high sensitivity.
• IP 66 sealed enclosure (sturdy and weatherproof
structure) suitable for outdoor installation
• You can manually set the camera direction – panning,
tilting and rotating.
• Backlight compensation through the center
measurement
• Various exposure modes (Auto Iris lens, CCD Iris,
Manual).
Network section, Control section
• Real-time monitoring of the image and sound from the
camera is possible using the Web browser on the
computer.
• MPEG4 video compression allows smooth streaming
of motion pictures with 30 fps (QVGA size). Motion
JPEG video streaming is also possible by selecting the
JPEG video compression format.
• The commercially available microphone can be
connected to the plug-in power type microphone input
(standard voltage 2.5 V) terminal (mini jack,
monaural).
• The motion detection function (in MPEG4 mode), one
sensor input terminal and two alarm output terminals
are equipped. You can send image as an attached file
of a mail or send to FTP server. You can also control
the peripheral equipments connected to the alarm
output terminals.
• The pre-alarm function and the post-alarm function
are equipped, by which the image and audio of before/
after the moment of alarm detection can be forwarded.
• Multicast streaming is equipped.
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use This User’s
Guide
This User’s Guide explains how to operate the SNC-
DF70N/DF70P Network Camera from a computer.
The User’s Guide is written to be read on the computer
display.
Precautions
This Sony product has been designed with safety in
mind. However, if not used properly electrical products
can cause fires which may lead to serious body injury.
To avoid such accidents, be sure to heed the following.
Heed the safety precautions
As this section gives tips on using the User’s Guide, read
it before you operate the camera.
Be sure to follow the general safety precautions and the
“Operating Precautions.”
In case of a breakdown
In case of system breakdown, discontinue use and
contact your authorized Sony dealer.
Jumping to the related page
When you read the User’s Guide on the computer
display, click on the sentence to jump to the related page.
In case of abnormal operation
Software display examples
• If the unit emits smoke or an unusual smell,
• If water or other foreign objects enter the cabinet, or
• If you drop the unit or damage the cabinet:
Note that the displays shown in the User’s Guide are
explanatory examples. Some displays may be different
from the ones which appear as you operate the
application software.
1
2
Disconnect the camera cable and the connecting
cables.
Printing the User’s Guide
Contact your authorized Sony dealer or the store
where you purchased the product.
Depending on your system, certain displays or
illustrations in the User’s Guide, when printed out, may
differ from those as portrayed on your screen.
Operating Precautions
Installation Manual (printed matter)
Operating or storage location
Avoid operating or storing the camera in the following
locations:
The supplied Installation Manual describes the names
and functions of parts and controls of the Network
Camera, connecting examples and how to set up the
camera. Be sure to read the Installation Manual before
operating.
• Extremely hot or cold places
• Exposed to direct sunlight for a long time, or close to
heating equipment (e.g., near heaters)
• Close to sources of strong magnetism
• Close to sources of powerful electromagnetic
radiation, such as radios or TV transmitters
• Locations subject to strong vibration or shock
Ventilation
To prevent heat buildup, do not block air circulation
around the camera.
Transportation
When transporting the camera, repack it as originally
packed at the factory or in materials of equal quality.
Cleaning
• Use a blower to remove dust from the lens or optical
filter.
• Use a soft, dry cloth to clean the external surfaces of
the camera. Stubborn stains can be removed using a
soft cloth dampened with a small quantity of detergent
solution, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene
or thinners as they may damage the surface finishes.
7
How to Use This User’s Guide / Precautions
Download from Www.Somanuals.com. All Manuals Search And Download.
System Requirements
These are the requirements for the computer that
displays the image or controls the camera.
Processor
Pentium III, 1 GHz or higher (Pentium 4, 2 GHz or
higher recommended)
RAM
256 MB or more
OS
Windows 2000/XP
Web browser
Internet Explorer Ver. 5.5 or Ver.6.0
8
System Requirements
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Install the IP Setup Program to your computer
following the wizard displayed.
If the Software License Agreement is displayed,
read it carefully and accept the agreement to
continue the installation.
Preparation
The Preparation section explains what the administrator
has to prepare for monitoring the images after
installation and connection of the camera.
Start the IP Setup Program.
The program detects the SNC-DF70N/DF70P
cameras connected to the local network and lists
them on the Network tab window.
Assigning the IP
Address to the Camera
To connect the camera to a network, you need to assign
a new IP address to the camera when you install the
camera for the first time.
You can assign an IP address in two ways:
• Using the setup program stored in the supplied CD-
ROM (see page 9)
• Using the ARP (Address Resolution Protocol)
This section explains how to assign an IP address to the
camera using the supplied setup program and how to
configure the network.
Before starting, connect the camera to a local network,
referring to “Connecting this Unit to a Local Network”
in the supplied Installation Manual.
Consult the administrator of the network about the
assigned IP address.
6
7
Click on the camera to which you want to assign a
new IP address in the list.
Assigning the IP Address Using the
Setup Program
1
Insert the supplied CD-ROM disc into your CD-
ROM drive.
After a short time a window will open displaying
the files on the CD-ROM.
The network settings for the selected camera are
displayed.
2
3
Click the Setup icon of IP Setup Program.
The “File Download” dialog opens.
Set the IP address.
Click Open.
To obtain the IP address automatically from a
DHCP server:
Note
Select Obtain an IP address automatically.
If you click “Save this program to disk” on the “File
Download” dialog, you cannot install correctly.
Delete the downloaded file, and click Setup icon
again.
The IP address, Subnet mask and Default gateway
are assigned automatically.
9
Assigning the IP Address to the Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
To specify the IP address manually:
Select Use the following IP address, and type the
IP address, Subnet mask and Default gateway in the
relevant boxes.
Note
You cannot change the Administrator name and
Administrator password in this step. To change
11 Confirm that all items are correctly set, then click
OK.
8
Set the DNS server address.
If “Setting OK” is displayed, the IP address is
correctly assigned.
To obtain the DNS server addresses
automatically:
Select Obtain DNS server address automatically.
12 To access the camera directly, double-click the
camera name on the list.
To specify the DNS server addresses manually:
Select Use the following DNS server address, and
type the Primary DNS server address and
Secondary DNS server address in the relevant
boxes.
The welcome page of the network camera SNC-DF70N/
DF70P is displayed.
Note
The Third DNS server address and Fourth DNS
server address are invalid for this camera.
Note
9
Set the HTTP port No.
If the IP address is not set correctly, the welcome page
does not appear after step 12. In this case, try to set the
IP address again.
Normally select 80 for the HTTP port No. To use
another port number, select the text box and type a
port number between 1024 and 65535.
10 Type the Administrator name and Administrator
password.
The default settings of both items are “admin.”
10
Assigning the IP Address to the Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the Camera
Using the Web Browser
When the IP address has been assigned to the camera,
check that you can actually access the camera using the
Web browser installed in your computer.
Use Internet Explorer as the Web browser.
1
Start the Web browser on the computer and type the
IP address of the camera in the URL box.
The welcome page of “Network Camera SNC-
DF70N” or “Network Camera SNC-DF70P” is
displayed.
Notes
• If Automatic configuration is enabled in the Local
Area Network (LAN) Settings on Internet Explorer,
the image may not be displayed. In this case, disable
Automatic configuration and set the Proxy server
manually. For setting the Proxy server, consult your
network administrator.
• When you install ActiveX viewer on Windows 2000
or Windows XP, you should have logged in the
computer as the Administrator.
Tip
Every page of this software is optimized as display
character size Medium for Internet Explorer.
2
Click Enter.
The main viewer is displayed.
To display the Welcome page correctly
To operate the welcome page correctly, set the security
level of the Internet Explorer to Medium or lower, as
follows:
1
2
3
Select Tool from the menu bar for Internet
Explorer, then select Internet Options and
Security tab in sequence.
Click the Internet icon (when using the camera via
the Internet) or Local intranet icon (when using
the camera via a local network).
Set the slider to Medium or lower. (If the slider is
not displayed, click Default Level.)
When the main viewer is correctly displayed, the IP
address assignment is completed.
When using antivirus software in the
computer
When the main viewer of the camera is
displayed for the first time
• When you use antivirus software in your computer, the
camera performance may be reduced, for example, the
frame rate for displaying the image may be lower.
• The Web page displayed when you log in the camera
uses Java Script. The display of the Web page may be
affected if you use antivirus software in your
computer.
When you click Enter, “Security warning” is displayed.
When you click OK, the ActiveX control is installed and
the main viewer is displayed.
11
Accessing the Camera Using the Web Browser
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuring by the
Administrator
You can monitor the image of the camera only logging
in with the initial condition of this network camera. You
can also set various functions according to the install
position, network condition or purpose of the camera.
We recommend you configure the following items
before monitoring the image from the camera.
Setting contents
Setting menu
Set the camera function suitable for the installation place.
Set the format of the image sent from the camera (MPEG 4 or JPEG).
Select the brightness of the image sent from the camera.
Select the quality of the image sent from the camera.
MPEG4 Tab (page 31)
JPEG Tab (page 31)
Select the size of the image sent from the camera.
Image size (page 28)
Select weather the audio from the camera microphone is sent or not.
Accord date and time of the camera with those of the computer.
Make the setting for sending the monitor image attached to a mail.
Set the access right of the user for the camera.
Microphone (page 29)
Date & time Tab (page 26)
12
Basic Configuring by the Administrator
Download from Www.Somanuals.com. All Manuals Search And Download.
User
Function
Administrator
Operating the Camera
Full
Light View
Switch the TCP/
UDP transmission
mode (Available in
MPEG4 mode
only)
z
z
–
–
The Operating the Camera section explains how to
monitor the image from the camera using the Web
browser. Use Internet Explorer as the Web browser.
The functions of the camera should be set by the
Administrator. For setting the camera, see
Control the audio
z
z
z
z
z
Control the setting
menu
–
–
–
z Usable function
– Not usable function
Administrator and User
This network camera classifies the people who log in
into the Administrator and the User.
The access rights of the administrator and the user can
be set in “Setting the User — User setting Menu” on the
The Administrator can use all functions of this network
camera including camera setting. The functions the
User can use are monitoring the image and audio from
the camera, and controlling the camera. The Viewer
mode setting restricts the user's access right, and the
user is classified as the one of three types.
Each type of the user can use the following functions.
User
Function
Administrator
Full
Light View
Monitor a live
image
z
z
z
z
–
z
z
–
Watch date and
time
z
z
z
z
Control the frame
rate (Usable only
when JPEG mode
is selected)
Control the image
view size
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
–
–
–
–
–
–
–
Zoom a image by
the digital zoom
Save the still image
in the computer
Send an image file
to the FTP server
Send an image
attached to a mail
–
Record an image
on the inside
memory of the
camera
–
Control the Alarm
out of the I/O port
on the camera main
unit
z
z
–
–
13
Administrator and User
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Click Enter.
The main viewer appears.
Logging in to Homepage
— Welcome Page
With the ActiveX viewer
Logging in as a User
1
Start the web browser on the computer and type the
IP address of the camera you want to monitor.
The welcome page of Network Camera SNC-
DF70N/DF70P is displayed.
With the Java applet viewer
2
Select the viewer.
The usable viewers differ depending on the video
mode (page 28) of the camera.
Control the camera from the main viewer.
Note
When the video mode is set to MPEG4, you can
use ActiveX viewer only, and viewer selection is
not possible. (MPEG4 is default. See illustration on
Step 1 above.)
If the Welcome page does not activate correctly, the
security level of the Internet Explorer may be set to
correctly” on page 11 and check the security level.
When the video mode is JPEG, you can select
ActiveX viewer or Java applet viewer.
Displaying the setting window for
the administrator directly
Welcome page when the video mode is
JPEG
When the administrator sets the camera functions, the
setting window can be displayed directly from the
welcome page.
1
Click Setting on the welcome page.
The following dialog appears.
3
Select the viewer language.
Click English or Japanese at the bottom of the
welcome page.
14
Logging in to Homepage — Welcome Page
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Enter the user name and password for
Administrator, then click OK.
To check the Java version
Select Tool from the menu bar of Internet Explorer, then
select Internet Option and the Advanced mode tab in
sequence, and check the version of Java displayed in
Java (Sun) is one of the versions specified below. If the
item Java (Sun) is not displayed, Java is not installed.
You need to install Java.
The user name “admin” and the password “admin”
are set at the factory for the Administrator. You can
change them on the User setting menu in the
The Administrator menu appears.
Java Plug-in Ver. 1.4.2_01, Ver. 1.4.2_02, Ver. 1.4.2_03,
Ver. 1.4.2_04
To enable Java Plug-in
Check “Use Java2v1.4.2_xx for <applet> (requires
restart)” in “Java (Sun)”.
To install Java Plug-in
Download Java 2 Runtime Environment, Standard
Edition (JRE) from the homepage of Sun Microsystems,
Inc., and install it following the instructions on the
installer.
Notes
• If Automatic configuration is enabled in the Local
Area Network (LAN) Settings on Internet Explorer,
the image may not be displayed. In this case, disable
Automatic configuration and set the Proxy server
manually. For setting the Proxy server, consult your
network administrator.
• When you install ActiveX viewer on Windows 2000
or Windows XP, you should have logged in the
computer as the Administrator.
About Viewers
You can use the following viewer according to the Video
mode setting in the camera setting menu on the
ActiveX viewer
This viewer can monitor the image in both video modes
MPEG4 and JPEG.
Tip
Every page of this software is optimized as display
character size Medium for Internet Explorer.
You have to install it when you access to the main viewer
at the first time.
When you are going to display the main viewer
of the camera for the first time
When you log in the network camera using ActiveX
viewer for the first time (clicking Enter to enter the
main viewer), the Security Warning appears. Click Yes
and install ActiveX Control. You can use all the
functions of the viewer by using ActiveX Control.
Java applet viewer
You can select this viewer when the camera video mode
is set to JPEG. The frame rate is lower than the ActiveX
viewer.
The Java applet viewer operates only when Java is
installed and Java (Sun) is enabled. If it does not
operated correctly, check if the specified Java version
has been installed successfully and Java (Sun) is
enabled.
15
Logging in to Homepage — Welcome Page
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Control Section
Configuration of Main
Viewer
Frame rate
This section explains the functions of the parts and
controls of the main viewer. For a detailed explanation
on each part or control, see the specified pages.
(Displayed only when the camera Video mode (page 28)
is set to JPEG.)
Main viewer
Selects the frame rate to transmit images.
View size
Selects the view size to be displayed. (page 18)
Digital zoom
Click to change the size of the digital zoom. (page 18)
Monitor image
section
Camera control
section
Main menu
Main menu
Capture
Click this button to capture a still image shot by the
camera and to store it in the computer. (See “Capturing
Setting
Click this button to display the Administrator menu.
You can operate this function only when logging in as
the administrator.
Trigger
(Displayed only when the camera Viewer mode
enabled on the Trigger Setting menu (page 48).)
Home
Displays the Welcome page.
Select the function you want to use from the list box and
click the icon. Then you can send the monitor image of
memory (page 20), switch the Alarm output to On/Off
(page 20) and switch the day/night function to On/Off
Player
Click this button to download the “SNC video player”
application program built in the camera. The SNC video
player allows you to play video/audio data recorded on
the camera with your computer. (See “Using the SNC
Transmission (Switching the TCP/
UDP transmission mode)
(Displayed only when the camera Video mode (page 28)
is set to MPEG4 and you are using the ActiveX viewer.)
Each click switches the transmission mode of the video/
audio data among TCP mode, UDP (Unicast) mode and
16
Configuration of Main Viewer
Download from Www.Somanuals.com. All Manuals Search And Download.
The last selected mode is saved in the computer, and it
will be selected at the next starting.
Controlling the Monitor
Image
You can monitor the camera image on the monitor
window of the main viewer.
(Volume)
On.)
Drag the bar of
When you click
icon to adjust the volume.
icon, the icon changes to and
the audio output stops. To output the audio, click
again.
Monitoring the camera image
1
Log in to the home page to display the main viewer.
as a User”.
Note
If the volume icon is not displayed in the case you are
using Java applet viewer, Audio codec may not be set
correctly.
To check if Java is installed correctly, refer to “Java
Monitor Image
2
Select the frame rate (only when the camera Video
mode is set to JPEG).
Click the Frame rate list box to select the frame
rate for transmitting the image. The selectable
frame rates are the following:
SNC-DF70N:
1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25, 30
SNC-DF70P:
1, 2, 3, 4, 5, 6, 8, 12, 16, 20, 25
The numbers indicate “fps” (the number of frames
transmitted per second).
The image shot by the camera is shown here. Date and
time is displayed at the top of the window.
Note
The frame rate options indicate the maximum
number of frames that can be transmitted.
The number of frames actually transmitted may
vary depending on network environments and
camera settings (image size and image quality
settings).
17
Controlling the Monitor Image
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Select the view size.
Capturing a Monitor
Image
You can capture a monitoring image as a still image and
save it in the computer.
Click View size box list box to select the view size
from among Auto, 640 × 480, 320 × 240 and 160 ×
120.
Auto is determined by the image size specified with
Image size on the Camera setting menu (page 28).
Capturing a monitor image
1
2
Monitor the camera image in the monitor window.
Zooming in the monitor image
Click Capture icon.
The still image of the moment when you click is
captured, and the still image is displayed in the
monitor window.
1
2
Click
Digital zoom icon.
Click the point you want to zoom in.
The image is expanded by about 1.5 times with the
clicked point at the center.
With the ActiveX viewer
The digital zoom icon changes to
.
3
To cancel zooming in, click
icon.
With the Java applet viewer
3
To cancel the still image, click Cancel or Close.
18
Capturing a Monitor Image
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving the captured image
Sending an Image File
With the ActiveX viewer
You can send a captured still image with an attached
mail or to the FTP server.
1
2
Capture the monitor image.
To use this function, you need to make the e-
Mail(SMTP) and FTP client active, and set the address
properly in the Trigger setting menu on the
Click Save.
Save As dialog appears.
Sending a Monitor Image via e-Mail
1
2
Monitor the image on the monitor window.
Select e-Mail from the Trigger list box.
3
Click
Trigger icon.
The still image of the moment when you click is
captured, and the mail attached with the image file
is sent to the mail address you have set.
3
4
Select JPEG or Bit map as Save as type.
Type on File name and specify Save in, then click
Save.
Sending a Monitor Image to an FTP
Server
With the Java applet viewer
1
2
Capture the monitor image.
1
2
Monitor the image on the monitor window.
Right-click the mouse to display the menu and
select Save with a new name.
Select FTP from the Trigger list box.
Save Picture dialog appears.
3
Click
Trigger icon.
The still image of the moment when you click is
captured, and the image file is sent to the FTP
server.
3
4
Select JPEG or Bit map as Save as type.
Type in File name and specify Save in, then click
Save.
19
Sending an Image File
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a Still Image
in the Built-in Memory of
the Camera
You can capture a camera image as a still image and
record it in the built-in memory of the camera.
To use this function, you need to make Image memory
active and to set details of the image memory in the
trigger setting menu on the Administrator menu
Controlling Alarm output
You can control the Alarm output On (short-circuit) and
Off (open).
To use this function, you need to make Alarm output
active in the Trigger setting menu on the Administrator
1
2
Monitor the image on the monitor window.
Select Alarm output 1 or Alarm output 2 from the
Trigger list box.
1
2
Monitor the image on the monitor window.
Select Image memory from the Trigger list box.
3
Click
Trigger icon.
Each click switches the Alarm output between On
(short-circuit) and Off (open) alternately.
3
Click
Trigger icon.
Tip
The still image of the moment when you click is
captured, and the image file is recorded in the built-
in memory of the camera.
For the connection of peripheral devices to the Alarm
output of the I/O port, see the supplied Installation
Manual.
20
Recording a Still Image in the Built-in Memory of the Camera / Controlling Alarm output
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Day/Night
Function
You can control the Day/Night On (night mode) and Off
(day mode). To use this function, you need to make Day/
Night active in the Trigger setting menu on the
Switching TCP/UDP
Transmission Mode
You can select the communication port of the video/
audio data as TCP or UDP.
This function can be used when the Video mode
used.
1
2
Monitor the image on the monitor window.
1
2
Display the main viewer.
Select Day/Night from the Trigger list box.
Click
TCP/UDP transmission selector icon.
Transmission mode selector dialog appears.
3
Click
Trigger icon.
Each click switches the Day/Night between On
(night mode) and Off (day mode) alternately.
3
Click one of the buttons TCP, UDP (Unicast) or
UDP (Multicast).
TCP: Usually select this.
When TCP is selected as the communication port,
HTTP communication is adopted for video/audio
communication.
HTTP is the protocol used for reading a usual Web
page.
In an environment capable of reading Web page,
you can watch or listen to the video/audio by
selecting TCP port.
UDP (Unicast): When UDP (Unicast) is selected
as the communication port, RTP (Real-time
Transport Protocol) is adopted for video/audio
communication. As RTP is the protocol for running
video/audio data, video/audio can be played
smoother than when TCP (HTTP) is selected. If the
fire-wall is installed between the camera and the
computer, or depending on the network
environment, the video/audio may not played
properly when UDP (Unicast) is selected. In this
case, select TCP.
UDP (Multicast): You can select this when the
(Multicast) is selected as the transmission port,
RTP (Real-time Transport Protocol) and UDP
multicast techniques are adopted for video/audio
transmission. By selecting it, the network
transmission load of the camera can be reduced. If
21
Controlling Day/Night Function / Switching TCP/UDP Transmission Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
a router which does not correspond to the multicast
or the fire-wall is installed between the camera and
the computer, the video/audio may not played
properly. In this case, select TCP or UDP
(Unicast).
4
Click OK to close the dialog.
If you do not change the transmission setting, click
Cancel.
22
Switching TCP/UDP Transmission Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrating the Camera
Basic Operations of
Administrator Menu
The Administrating the Camera section explains how to
set the functions of the camera by the Administrator.
For monitoring the camera image, see “Operating the
You can set all functions to suit the user's condition in
the Administrator menu.
Click Setting in the welcome page to display the
Administrator menu.
This section explains the basic operations and each
option.
How to set Administrator menu
1
Log in the home page to display the welcome page.
2
Click Setting in the welcome page.
The authentication dialog appears. Enter the user
name and password for Administrator.
The user name “admin” and password “admin” are
set at the factory for the Administrator.
Administrator menu appears.
The following steps also display the Administrator
menu.
1 Click Enter in the welcome page to display the main
viewer.
2 Click
Setting icon in the main viewer to display
the Administrator menu.
3
Click the menu name (example: System) on the left
side of the Administrator menu.
The clicked setting menu appears.
23
Basic Operations of Administrator Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: System setting menu
General note on setting menus
After changing a setting on a setting menu, wait at least
10 seconds before turning off immediately the power of
the camera.
If the power is turned off immediately, the changed
setting may not be stored correctly.
Configuration of Administrator
Menu
4
Select the tab above the setting menu, and set each
setting option in the tab.
Example: “System” setting menu “Date & time”
tab
System
Displays the System setting menu.
page 25).
Camera
Displays Camera setting menu for setting of camera
image and audio. (“Setting the Camera Image and Audio
and setting options.
5
After setting, click OK.
The setting contents become active.
Network
Displays the network setting menu for setting of
network connection. (“Configuring the Network —
Click Cancel to invalidate the set values and return
to the previous settings.
User
Buttons common to every setting menu
Displays the user setting menu for setting the user name
and the password to log in. (“Setting the User — User
The following buttons are displayed on the setting
menus where they are necessary. The functions of the
buttons are the same on every setting page.
Security
Displays the security setting menu for specifying the
computer allowed to connect to the camera. (“Setting the
Click this button to validate the settings.
e-Mail (SMTP)
Click this button to invalidate the set values and return to
the previous settings.
Displays the e-Mail (SMTP) setting menu for sending an
24
Basic Operations of Administrator Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
FTP client
Displays the FTP client setting menu for sending an
image file to FTP server. (“Sending Images to FTP
Configuring the System
— System setting menu
When you click System on the Administrator menu, the
System setting menu appears.
Use this menu to perform the principal settings of the
software.
The System setting menu is composed of five tabs that
are System, Date & time, Initialization, System Log
and Access Log.
Image memory
Displays the image memory setting menu for recording
a video/audio file in the built-in memory of the camera.
FTP server
Displays the FTP Server menu for setting the FTP server
function of the camera.
System Tab
Alarm output
Displays the alarm out setting menu for the alarm out
terminal of the camera. (“Setting the Alarm Output —
Trigger
Displays the trigger setting menu for the operations
when you click the trigger button in the main viewer.
Schedule
Displays the schedule setting menu for FTP client
function, e-Mail (SMTP) function, Image memory
function and Alarm out function and so on. (“Setting the
Title bar name
Type a name to display on the title bar up to 32
characters. The characters typed here are displayed on
the title bar of the Web browser.
Alarm buffer
Welcome text
Displays the alarm buffer setting menu for the buffer
which records the image and audio on the alarm
detection. (“Setting the Alarm Buffer — Alarm buffer
Type a text to show on the welcome page, in HTML
format, up to 1,024 characters. Use the <BR> tag for a
line break. (A line break is equivalent to 2 characters.)
Serial number
Displays the serial number of the camera.
Motion detection
Displays the Motion detection setting menu for the
motion detection function built into the camera.
Software version
The software version of this camera is displayed.
Default URL
Select the homepage to be displayed when you enter the
IP address of the camera in the web address box of the
browser.
To display the homepage built in the camera
Select /index.html.
To display your individual homepage
You can display your favorite homepage. Store the
HTML file in the built-in flash memory using the
25
Configuring the System — System setting menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Homepage Installer included in the supplied
CD-ROM.
Adjust
Select to set the day and time.
Keep current setting: Select when you do not need to
set the date and time.
Synchronize with PC: Select when synchronizing the
camera's date and time with those of the computer.
Manual setting: Select when you want to set the
camera's date and time manually.
1
2
Select User Setting/user/.
Type the path of the HTML file in the text box up to
64 characters.
Tip
Select the lower 2-digits of year, month, date, hour,
minutes and seconds from each drop-down list.
Synchronize with NTP: Select when synchronizing the
camera's date and time with those of the time sever
called NTP server (Network Time Protocol). Set the
NTP server name and the Interval.
Even when you select User Setting/user/, the home
page inside the camera can be displayed by typing the
following URL in the address box of the browser.
Example: When the IP address of the camera is set to
192.168.0.100
NTP server name
Type the host name or IP address of the NTP server, up
to 64 characters.
OK/Cancel
24.
Interval time
Date & time Tab
Select the interval at which you want to adjust the
camera's time referring to the NTP server' time, between
1 and 24 hours. The set interval is a guide, and does not
indicate the exact time.
Note
The setting time may not accord with the exact time
according to the network environment.
Time zone
Set the time difference from Greenwich Mean Time in
the area where the camera is installed.
Select the time zone where the camera is installed from
the drop-down list.
Automatically adjust clock for daylight saving
time changes
When you select it, the clock is automatically adjusted
according to the daylight saving time of the selected
time zone.
Current date & time
Displays the date and time set on the camera.
Note
Note
After you have purchased the camera, be sure to check
the date and time of the camera and set them if
necessary.
If the time zone selected on the Time zone menu is
different from that set on the computer, the time is
adjusted using the time zone difference and set on the
camera.
PC clock
Displays the date and time set on your computer.
OK/Cancel
24.
Date & time format
Select the format of date and time to be displayed on the
main viewer from the drop-down list.
You can select from among yyyy-mm-dd hh:mm:ss
(year-month-day hour:minute:second), mm-dd-yyyy
hh:mm:ss (month-day-year hour:minute:second), and
dd-mm-yyyy hh:mm:ss (day-month-year
hour:minute:second).
26
Configuring the System — System setting menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Firmware upgrade
Initialize Tab
Use this when upgrading the camera software. Click
Browse and specify the file for upgrading, then click
OK. “Upgrade firmware? Are you sure?” is displayed.
Click OK and upgrading starts. After completion, the
camera starts again.
Notes
• Use only the upgrade file special to this camera. If you
do not, a problem may occur.
• Do not turn off the camera until the upgrading will be
completed.
System log Tab
Reboot
Reboots the camera.
Click Reboot, and “The SNC-DF70 will be rebooted.
Are you sure?” appears. Click OK to reboot the camera.
It takes about two minutes to start again.
Factory default
Resets the camera to the factory settings.
Click Factory default, and “Set up data will be
initialized. Are you sure?” appears. When you click
OK, the Network indicator and the Power indicator on
the camera start to blink. After adjustments of the
default settings have finished, the camera reboots
automatically. Do not turn off the camera until the
camera reboots.
System log
The data of the software activity of the camera are
recorded in this. It includes data that are useful when a
problem occurs.
Click Reload to reload to the latest data.
Tip
The camera can also be reset to the factory settings by
pressing the reset switch on the camera. For details, see
the supplied Installation Manual.
Access log tab
Backup setting data
Saves the setting data of the camera in a file.
Click Save, and follow the instructions on the browser to
specify the folder and save the setting data of the
camera. The file name preset at the factory is “snc-
df70.cfg.”
Restore setting
Loads the stored setting data of the camera.
Click Browse and select the file in which the setting data
is stored. Then, click OK, and the camera is adjusted
according to the loaded data and restarted.
Access log
The access record of the camera is displayed.
Click Reload to reload to the latest data.
Note
With Restore setting, some items in the Network setting
27
Configuring the System — System setting menu
Download from Www.Somanuals.com. All Manuals Search And Download.
When you select On, set Multicast address, Multicast
video port number and Multicast audio port number
properly.
Multicast address: Type the multicast address used on
the Multicast streaming.
Multicast video port number: Specify the video
transmission port number used on the Multicast
streaming.
Multicast audio port number: Specify the audio
transmission port number used on the Multicast
streaming.
Setting the Camera
Image and Audio
— Camera setting Menu
When you click Camera on the Administrator menu,
the Camera setting menu appears.
Use this menu to set the functions of the camera.
The Camera setting menu consists of 6 tabs: Common,
Picture, Day/Night, MPEG4, JPEG and Reset.
Image size
You can select the image size sent from the network
camera.
Common Tab
640 × 480 (VGA), 480 × 360, 384 × 288, 320 × 240
(QVGA), 256 × 192 or 160 × 120 (QQVGA) can be
selected.
Image mode
The image output from the camera can be selected from
Field mode or Frame mode. When Frame mode is
selected, level resolution goes up. However, an edge
portion will become notched if what is taken is moving.
Notes
If you set the Image size to 320 × 240 (QVGA), 256 ×
192 or 160 × 120 (QQVGA), the Image mode is fixed
in the Field mode.
Video mode
Select the output format of the camera image.
Cropping
When the image size is set to 640 × 480 (VGA), you can
crop a portion of the image and display the cropped
image on the computer. With the cropping, the
transmitting data size, and thus, the network load is
reduced and a higher frame rate is obtained.
MPEG4 or JPEG can be selected.
Unicast streaming
Specify the transmission port number of the video data
and audio data used when UDP (Unicast) is selected
with the TCP/UDP transmission switching icon in the
main viewer
Video port number: Specify the transmission port
number of the video data. It is initially set to 50000.
Specify an even number from 1024 to 65534.
Audio port number: Specify the transmission port
number of the audio data. It is initially set to 50002.
Specify an even number from 1024 to 65534.
Select On for cropping the image, or Off for no
cropping.
Notes
• When Cropping is set to On, Motion detection
function does not work.
• While Cropping is set to On, the image of the
composite video signal output from the video output
connector of the camera may be distorted.
Multicast streaming
Set whether the camera uses the Multicast streaming or
not. It reduces sending load on the camera by making the
computer of the same segment network (not above the
router) receive the same transmitting data.
Select On to allow the multicast sending and Off not to
allow.
To crop an image
1
2
Set the Image size to 640 × 480(VGA).
The Cropping is displayed.
Set the Cropping to On and click the Area setting
button.
The “Area setting” display appears.
28
Setting the Camera Image and Audio — Camera setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Specify the cropping area.
Speaker output
Click the left button of the mouse on the still image
and drag it diagonally. The red frame that appears
as you drag indicates the cropping area.
Set whether you output the audio which is input to the
audio input connectors of your computer to the speaker
(active speaker for example) connected to the camera
line output connectors by using SNC audio upload tool
included in the supplied CD-ROM.
Still image
Select On to accept the audio data transmission from
SNC audio upload tool.
OK/Cancel
24.
Picture Tab
You can set the color condition, exposure, etc. of the
camera.
Red trimming Click the left button of the mouse on
frame
the still image and drag it.
4
5
Click OK at the bottom of the window.
The cropped image is displayed on the main viewer.
To close the image, click
corner.
in the upper-right
Color
Select Color or Monochrome for the image.
Microphone
Select whether you send the audio from the microphone
input connector. Select On to send the audio from this
network camera.
Exposure mode
Select the exposure adjustment mode from among Auto
Iris lens, CCD Iris, and Manual.
The setting items required for each setting appear.
Auto Iris lens: Select this option when you use an
autoiris lens.
Note
When you change the Microphone setting, click
Refresh of the browser to reflect the change in the
opening main viewer page.
CCD Iris: Select this option when you use a fixed-iris
lens to adjust the exposure using the electronic
shutter and AGC (Automatic Gain Control).
Manual: Adjust the electronic shutter and gain
manually.
Mic volume
Set the volume level of the audio input from the
microphone input connector. It is adjustable from –10 to
+10.
Audio codec
Select the bit rate when you send the audio from the
microphone input connector. G.711 (64kbps), G.726
(40kbps), G.726 (32kbps), G.726 (24kbps) or G.726
(16kbps) can be selected.
Note
When the bit rate is set to other than G.711(64bps), the
audio is not output in the case you are using Java applet
viewer.
29
Setting the Camera Image and Audio — Camera setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
AGC (Automatic Gain Control)
Adjusts the gain automatically according to the lighting
conditions of the subject.
OK/Cancel
24.
Back light compensation
Select On to activate the backlight compensation, or Off
to deactivate it.
User preset
You can save the present settings in the camera as the
custom, or you can load the settings saved in the camera.
Save: Click to save the present settings of the Picture
tab.
Load: Click to load the saved settings. To use them,
click OK.
Lens adjust
Select the iris convergence level for the auto-iris lens
from 0 to 255.
Shutter mode
Select the electronic shutter mode, Auto or Manual.
The setting items required for each setting appear.
Day/Night Tab
Use this tab to set the day/night function of the camera.
Shutter speed
Select the electronic shutter speed from among the
following:
SNC-DF70N:
1/10000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/100,
1/60 (seconds).
SNC-DF70P:
1/10000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/120,
1/50 (seconds).
Tip
Flicker from fluorescent lamps or similar can be reduced
by setting the Shutter mode to Manual and Shutter
speed to 1/100
.
The day/night function consists of five tabs.
Gain
Select the gain (dB) from among the following:
0 dB, 6 dB, 12 dB, 18 dB
Disable
Always works in day mode.
Brightness
Auto
Tweaks the exposure set in the exposure mode. It is
brighter when a large value is selected, and it is darker
when a small value is selected. The value among –5 to 5
can be set.
Normally works in day mode. It switches automatically
to night mode in a dark place.
The switching timing can be adjusted by the following
parameters. When the auto gain control is set to Off, the
camera does not switch to the night mode.
Level: High or Low indicates a brightness level.
Time: Select invalid time so that the camera does not
react to changes in light and darkness.
Saturation
Select the saturation in 7 steps, from –3 to 3.
Selecting 3 gives the image with the highest saturation.
Manual
Sharpness
Switch the day/night mode manually. When you select
Manual, On and Off are displayed. When you select
On, the camera works in night mode. When you select
Off, it works in day mode.
Select the sharpness in 7 steps, from –3 to 3.
Selecting 3 gives the image with the highest sharpness.
Contrast
Timer
Select the contrast in 7 steps, from –3 to 3.
Normally works in day mode. It switches to night mode
at the time you set in the Schedule setting menu. The
day/night function normally works in day mode.
Selecting 3 gives the image with the highest contrast.
30
Setting the Camera Image and Audio — Camera setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Sensor
Note
Controls day/night mode by synchronizing with the
sensor input.
The selected frame rate and bit rate are a tentative value.
The actual frame rate and bit rate may be different
according to the image size, the shooting scene or the
network condition.
The camera works in night mode while the sensor input
is being detected.
Note
I-picture interval
When a signal is input from the 1 pin (sensor input +)
and 2 pin (sensor input - (GND)) of the I/O cable, the
camera works in night mode regardless of the set mode.
For pin assignment, see the supplied Installation
Manual.
When you select the day/night function in Trigger setting
menu after selecting Auto, Timer or Sensor in the Day/
Night tab, you can switch the day/night mode from the
Trigger on the main viewer.
Set the I-picture inserting interval of MPEG4. I-picture
is the compression data serving the basic point when the
data compressed by MPEG4 is depressed. In the
condition that errors tends to happen, such as the
network environment variation, the distortion of the
image is reduced by selecting a small value. The
selectable values are 1, 2, 3, 4 and 5 seconds.
Auto rate control
OK/Cancel
This function adjusts the frame rate and the bit rate
automatically so that the camera plays a smooth image
to suit the connected computer environment. If On is
selected, the rate of MPEG4 image is automatically
adjusted.
24.
MPEG4 Tab
Note
The maximum transmission rate will be the values set in
Frame rate and Bit rate.
OK/Cancel
24.
JPEG Tab
Frame rate
Set the frame rate of the MPEG image.
The selectable frame rates are the following:
SNC-DF70N:
1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25, 30
SNC-DF70P:
1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25
The numbers indicate “fps” (the number of frames
transmitted per second).
Bit rate
Frame rate
Set the maximum frame rate of JPEG image that can be
monitored on the computer.
The selectable frame rates are the following:
SNC-DF70N:
Set the bit rate of MPEG image transmission for a line.
Selectable values are 64, 128, 256, 384, 512, 768, 1024,
1536 and 2048 kbps.
5, 6, 8, 10, 15, 20, 25, 30
31
Setting the Camera Image and Audio — Camera setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
SNC-DF70P:
5, 6, 8, 10, 15, 20, 25
The numbers indicate “fps” (the number of frames
transmitted per second).
Configuring the Network
— Network setting Menu
When you click Network on the Administrator menu,
the Network setting menu appears.
Use this menu to configure the network to connect the
camera and the computer.
The Network setting menu consists of 3 tabs: Network,
PPPoE and Dynamic IP address notification.
Image quality
Set the quality of JPEG image.
Selectable values are from Level 1 to Level 5.
Selecting level 5 gives the image with the highest
quality.
Bandwidth control
When the video mode is set to JPEG, the network
bandwidth can be limited. Selectable bandwidths are
0.5, 0.6, 0.7, 0.8, 0.9, 1.0, 2.0, 3.0, 4.0, and Unlimited
Mbps. When you do not wish to limit the bandwidth,
select Unlimited.
Network Tab
This section provides the menus for connecting the
camera through the network cable.
OK/Cancel
24.
Reset Tab
MAC address
Displays the MAC address of the camera.
Obtain an IP address automatically
(DHCP)
DHCP server is installed on the network. Select it when
the IP address is assigned by DHCP server. IP address is
assigned automatically.
Reset
Note
Click Reset, and “Camera menu setting is reset to
default. Are you sure?” is displayed. To reset to default,
click OK.
When you set Obtain an IP address automatically
(DHCP), make sure that DHCP server is working on the
internet.
Use the following IP address
Select this when a fixed IP address is set.
IP address
Type the IP address of the camera.
Subnet mask
Type the subnet mask.
32
Configuring the Network — Network setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Default gateway
Type the default gateway.
PPPoE Tab - Setting of PPPoE
Connection
Use it when you connect the camera with PPPoE (Point-
to-Point Protocol over Ethernet). PPPoE connection is
the protocol that is widely used in xDSL (digital affiliate
line such as ADSL, VDSL or SDSL) as the
Obtain DNS server address automatically
Select this to obtain the address of DNS server
automatically. It can be set only when Obtain an IP
address automatically (DHCP) is selected.
authentication and connection system.
Note
When you select “Obtain DNS server address
automatically”, make sure that DHCP server is active on
the network.
Use the following DNS server address
Select this when you set the fixed address as the IP
address of DNS server.
Primary DNS server
Type the IP address of the primary DNS server.
Secondary DNS server
Type the IP address of the secondary DNS server, if
necessary.
PPPoE
Set whether you connect the camera using PPPoE
function or not. When On is selected, PPPoE connection
is used.
HTTP port number
Normally select 80. If you want to use a port number
other than 80, select the text box and type a port number
between 1024 and 65535.
IP address
When you connect to the network by PPPoE function, IP
address obtained at PPPoE connection is displayed.
Note
When you have set the HTTP port number to a number
other than 80 on the Network setting page or in the Setup
Program, access the camera by typing the IP address of
the camera on the web browser, as follows:
User ID
Type the user ID for the authentication necessary for
PPPoE connection. Type it up to 64 characters.
Example: when HTTP port number is set to 8000
Password
Type the password for the authentication necessary for
PPPoE connection. Type it from 1 to 32 characters.
Re-type password
To certain the password, re-type the characters as them
typed in the password box.
OK/Cancel
24.
Obtain DNS server address automatically
Select it to obtain the address of DNS server
automatically.
Use the following DNS server address
Select this when you set the fixed address as the IP
address of DNS server.
33
Configuring the Network — Network setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Primary DNS server
Type the IP address of the primary DNS server.
Dynamic IP address notification
Tab — Notifying the IP Address
When the DHCP setting is set to On or PPPoE setting is
set to On on the Network tab, you can send notification
of the completion of the network settings using the
SMTP or HTTP protocol.
Secondary DNS server
Type the IP address of the secondary DNS server.
OK/Cancel
24.
e-Mail (SMTP) notification
Select On to send an e-Mail when the DHCP setting is
completed.
SMTP server name
Type the name or IP address of the SMTP server you
want to use for sending an e-Mail, up to 64 characters.
Authentication
Select the authentication required when you send an e-
Mail.
Off: Select if no authentication is necessary when an e-
Mail is sent.
On: When authentication is necessary an e-Mail is sent,
select one of the authentication methods from the
followings..
SMTP: Select if authentication is necessary when an
e-Mail is sent.
POP before SMTP: Select when POP before
SMTP is necessary when an e-Mail is sent.
Note
When you set to On, make sure to select either or both
SMTP or/and POP before SMTP.
POP server name
It is necessary when the POP before SMTP is selected
in Authentication.
Type the POP (receiving mail) server name up to 64
characters. Or type the IP address of the POP server.
This setting is necessary when the SMTP server which
sends e-Mails performs authentication using the POP
user account.
34
Configuring the Network — Network setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
User name, Password
Proxy port number
Type the user name and Password of the user who has
the mail account. This setting is necessary when the
SMTP server which sends e-Mails performs
authentication.
Specify the port number when you send HTTP
commands via the proxy server. Set a port number
between 1024 and 65535.
Method
Recipient e-Mail address
Select the HTTP method GET or POST.
Type the recipient e-Mail address up to 64 characters.
You can specify only one recipient e-Mail address.
OK/Cancel
24.
Administrator e-Mail address
Type the e-Mail address of the camera administrator, up
to 64 characters. This is used as the reply address or the
address for a system mail from the mail server.
About the special tags
You can use the following five special tags to allow the
notification of the settings acquired by the DHCP, such
as an IP address. Type the tags in the parameter section
of the URL that you describe in the Message field of the
HTTP.
Subject
Type the subject/title of the e-Mail up to 64 characters.
Message
<IP>
Type the text of the e-Mail up to 384 characters. (A line
break is equivalent to 2 characters.) You can describe the
information of the acquired IP address, etc. using the
special tags mentioned below.
Use this tag to embed the IP address acquired by the
DHCP in the text or parameter.
<HTTPPORT>
Use this tag to embed the specified HTTP server port
number in the text or parameters.
HTTP notification
Select On to output a command to the HTTP server
when the DHCP setting is completed. Using this
function, you can configure a useful system, for
example, to view the access log stored in the HTTP
server or start an external CGI program.
<MACADDRESS>
Use this tag to embed the MAC address of the interface
whose IP address you have acquired by the DHCP, in the
text or parameter.
URL
<MODELNAME>
Use this tag to embed the camera's model name (SNC-
DF70) in the text or parameter.
Specify the URL to send HTTP commands, up to 256
characters. The URL is normally composed as follows:
<SERIAL>
Use this tag to embed the camera's serial number in the
text or parameter.
ip_address: Type the IP address or host name of the host
to which you want to connect.
:port: Specify the port number to which you want to
connect. If you want to use the well-known port
number 80, you do not need to input this value.
path: Type the command name.
parameter: Type the command parameter if necessary.
You can use the special tags mentioned below for the
parameters.
Proxy server name
When you send HTTP commands via a proxy server,
type the name or IP address of the proxy server, up to 64
characters.
35
Configuring the Network — Network setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewer authentication
Set whether the user is authenticated or not when the
main viewer is displayed.
When you select On, the main viewer is displayed to suit
the authenticated user. When you select Off, select the
view mode of the main viewer page which is displayed
without authentication from among Full, Light or View.
Setting the User
— User setting Menu
When you click User on the Administrator menu, the
User setting menu appears.
Use this menu to set the user names and passwords of
Administrator and up to 9 kinds of users (User 1 to User
9), and the access right of each user.
OK/Cancel
24.
Administrator, User 1 to 9
Specify User name, Password, Re-type password,
FTP user and Viewer mode for each user ID.
User name
Type a user name between 5 and 16 characters.
Password
Type a password between 5 and 16 characters.
Re-type password
To confirm the password, type the same characters as
you typed in the Password box.
FTP user
Set whether logging in to FTP server is allowed or not.
When you need to log in to FTP server, check it.
Viewer mode
If the user is authenticated when the main viewer is
displayed, you can select the viewer mode displayed
after authentication.
Full: You can operate all functions in this mode.
Light: You can operate the functions other than the
trigger button on the main viewer, TCP/UDP
switching button on the main viewer, and the frame
rate setting.
View: You can monitor only the camera image.
36
Setting the User — User setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Setting the Security
— Security setting Menu
You can access the camera even from a computer having
an IP address whose access right is set to Deny, if you
enter the user name and password set for the
Administrator boxes in the User setting menu.
When you click Security on the Advanced mode menu,
the Security setting menu appears.
Use this menu to limit the computers that can access the
camera.
OK/Cancel
24.
Security function
To activate the security function, select On.
If you do not wish to use the security function, select
Off.
Default policy
Select the basic policy of the limit from Allow and Deny
for the computers specified on the Network address/
Subnet 1 to Network address/Subnet 10 menus below.
Network address/Subnet 1 to Network
address/Subnet 10
Type the IP addresses and subnet mask values you want
to allow or deny access to the camera.
You can specify up to 10 IP addresses and subnet mask
values. For a subnet mask, type 8 to 32.
Select Allow or Deny from the drop-down list on the
right for each IP address/subnet mask .
Tip
The subnet mask value represents the bit number from
the left of the network address.
For example, the subnet mask value for “255.255.255.0”
is 24.
If you set “192.168.0.0/24” and “Allow,” you can allow
access from the computers having an IP address between
“192.168.0.0” and “192.168.0.255”.
37
Setting the Security — Security setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Authentication
Select the authentication required when you send an e-
Mail.
Off: Select if no authentication is necessary when an e-
Mail is sent.
On: When authentication is necessary an e-Mail is sent,
select one of the authentication methods from the
followings..
Sending an Image via
mail — e-Mail (SMTP) setting
Menu
When you click SMTP on the Administrator menu, the
SMTP setting menu appears.
SMTP: Select if authentication is necessary when an
e-Mail is sent.
POP before SMTP: Select when POP before
SMTP is necessary when an e-Mail is sent.
By using Mail (SMTP) function, you can send a mail
with attached image which has been shot linked with the
external sensor input or with the built-in motion
detection function. The image file can also be sent
periodically.
Note
e-Mail (SMTP) setting menu is composed of three tabs:
Common, Alarm sending and Periodical sending.
When you set to On, make sure to select either or both
SMTP or/and POP before SMTP.
POP server name
It is necessary when the POP before SMTP is selected
in Authentication.
Common Tab — Setting the SMTP
Function
Type the POP (receiving mail) server name up to 64
characters, or type the IP address of the POP server. This
setting is necessary when the SMTP server which sends
e-Mails performs authentication using the POP user
account.
User name, Password
Type the user name and Password of the user who has
the mail account. This setting is necessary when the
SMTP server which sends e-Mails performs
authentication.
Recipient e-Mail address
Type the recipient e-Mail address up to 64 characters.
You can specify up to three recipient e-Mail addresses.
e-Mail (SMTP)
Administrator e-Mail address
Type the Administrator e-Mail address up to 64
characters.
This address is used for reply mail and sending system
messages from the SMTP server.
Select On when you use the e-Mail (SMTP) function.
The common setting options are displayed below.
If you do not wish to use the e-Mail (SMTP) function,
select Off and click OK.
Notes
Subject
• During transmission of an image file via mail, the
frame rate and operation performance of the monitor
image of the main viewer decline.
• While the camera video mode is set to MPEG4, the
image of the composite video signal output from the
video output connector of the camera may be distorted
during mail transmission.
Type the subject/title of the e-Mail up to 64 characters.
With respect to mail which is sent according to the alarm
detection when Alarm sending of the alarm tab is set to
On, the characters standing for the sensor type added to
the subject. SI is added for sensor input detection, and
MD is added for motion detection.
• You cannot send an audio file by using the mail
sending function.
Message
Type the text of the e-Mail up to 384 characters. (A line
break is equivalent to 2 characters.)
SMTP server name
Type the SMTP server name up to 64 characters, or the
IP address of the SMTP server.
38
Sending an Image via mail — e-Mail (SMTP) setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and two fixed
digits 00 is added to the Image file name.
OK/Cancel
24.
Tip
Alarm sending Tab — Setting the
mail sending mode when detecting
the alarm
A consecutive number added to Date & time and
Sequence number is used to identify each of multiple
files created with one alarm event.
Set to send the mail with connection to the alarm
detection by the external sensor input or by the built-in
motion detection function.
Sequence number clear
Click Clear to reset the Sequence number suffix to 1.
Alarm
Select the connected alarm.
Sensor input: The external sensor which is connected to
the sensor input of the camera I/O port.
Motion detection: Click Motion detection button, and
the Motion detection setting menu is displayed. You
Note
Motion detection works only when the camera Video
mode is set to MPEG4 and the Cropping is set Off.
Effective period
Set the period when the alarm detection is effective.
Always: The alarm detection is always effective.
Schedule: You can specify the period when the alarm
detection is effective in the schedule setting in the
other section.
Alarm sending
Select On to set to send mail with connection to the
alarm detection.
Click Schedule and the setting menu for the
Effective period is displayed. (“Setting the Schedule
File attachment
Set whether an image file is attached to the mail sent or
not.
When On is selected, the image file made by the settings
below is attached. When Off is selected, only the
message is sent.
OK/Cancel
24.
Image file name
Type the file name you want to assign to the image to
attach a mail. You can use up to 10 alphanumeric, -
(hyphen) and _ (underscore) for naming.
Suffix
Select a suffix to add to the file name.
None: No suffix is added. The Image file name is
assigned to the image to be sent via an e-Mail.
Date & time: The date & time suffix is added to the
Image file name.
The date/time suffix consists of lower two-digits of
year (2 digits), month (2 digits), date (2 digits), hour
(2 digits), minute (2 digits), second (2 digits), and
consecutive number (2 digits), thus 14-digit number
is added to the file name.
39
Sending an Image via mail — e-Mail (SMTP) setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective period
Periodical sending Tab — Setting
the periodical mail sending mode
You can set to send mails periodically.
Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the
periodical sending is effective in the schedule setting
in the other section.
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule —
OK/Cancel
24.
Periodical sending
Select On when you want to send mails periodically. If
you select Off, Periodical sending is not executed.
Image file name
Type the file name of the image attached to the mail up
to 10 alphanumeric, - (hyphen) and _ (under score).
Suffix
Select a suffix added to the file name used when the mail
is sent.
None: The name of the sent file will be the Image file
name.
Date & time: The date & time suffix is added to the
Image file name.
The date & time suffix consists of lower two-digits of
year (2 digits), month (2 digits), date (2 digits), hour
(2 digits), minute (2 digits) and second (2 digits), and
consecutive number (2 digits), thus 14-digit number
is added to the file name.
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and two fixed
digits 00 is added to the Image file name.
Sequence number clear
Click Clear and the suffix of the sequence number
returns to 1.
Interval
Type the interval at which you want to send a mail
periodically. You can set the hour (H) and minutes (M)
between 30 minutes and 24 hours (one day).
40
Sending an Image via mail — e-Mail (SMTP) setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Password
Type the password for the FTP server.
Sending Images to FTP
Server
— FTP client setting Menu
Re-type password
To confirm the password, type the same characters as
you typed in the Password box.
When you click FTP client on the Administrator menu,
the FTP client setting menu appears.
Passive mode
Use this menu to set up for capturing and sending still
images to an FTP server. By using FTP client function,
you can send the image and audio file which has been
shot and recorded linked with the external sensor input
or with the built-in motion detection function to FTP
server. The image file can also be sent periodically.
FTP client setting menu is composed of three tabs
Common, Alarm sending and Periodical sending.
Set whether you use the passive mode of FTP server or
not when connecting to FTP server. Select On to
connect to FTP server using the passive mode.
OK/Cancel
24.
Alarm sending Tab — Setting the
FTP client action when detecting
the alarm
Common Tab — Setting the FTP
Client Function
Set to forward the image and audio file to the specified
FTP server linked with the alarm detection by the
external sensor input or by the built-in motion detection
function.
FTP client function
To activate the FTP client function, select On. The FTP
client setting page appears.
When you do not wish to use the FTP client function,
select Off.
Alarm sending
Select On to send the image and audio file to FTP server
linked with the alarm detection.
Note
The frame rate and operability on the main viewer may
decrease while a file is being transmitted by the FTP
client function.
Remote path
Type the path to the destination up to 64 characters.
FTP server name
Type the FTP server name to upload still images up to 64
characters, or the IP address of the FTP server.
Image file name
Type the file name you want to assign to the images
when sending to the FTP server. You can use up to 10
alphanumeric characters, - (hyphen) and _ (underscore)
for naming.
User name
Type the user name for the FTP server.
41
Sending Images to FTP Server — FTP client setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Suffix
OK/Cancel
Select a suffix to add to the file name.
Date & time: The date & time suffix is added to the
Image file name.
24.
The date/time suffix consists of lower two-digits of
year (2 digits), month (2 digits), date (2 digits), hour
(2 digits), minute (2 digits) and second (2 digits), and
consecutive number (2 digits), thus 14-digit number
is added to the file name.
Periodical sending Tab — Setting
the Periodical FTP Client Activity
You can set to send an image file to FTP server
periodically.
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and an
consecutive 2 digits number is added to the Image
file name.
Tip
A consecutive number added to Date & time and
Sequence number is used to identify each of multiple
files created with one alarm event.
Sequence number clear
Click Clear to reset the Sequence number suffix to 1.
Alarm
Select the connected alarm.
Sensor input: The external sensor which is connected to
the sensor input of the camera I/O port.
Motion detection: Click Motion detection button, and
the Motion detection setting menu is displayed. You
Periodical sending
Select On when you want to use periodical sending. If
you select Off, Periodical sending is not executed.
Remote path
Type the remote path up to 64 characters.
Note
Motion detection works only when the Video mode is
set to MPEG4 and the Cropping is set to Off.
Image file name
Type the file name of the image sent to FTP server up to
10 alphanumeric characters, - (hyphen) and _ (under
score).
Effective period
Set the period when the alarm detection is effective.
Always: The alarm detection is always effective.
Schedule: You can specify the period when the alarm
detection is effective in the schedule setting in the
other section.
Note
You cannot send the audio file by using the periodical
sending function of FTP.
Click Schedule and the setting menu for the
Effective period is displayed. (“Setting the Schedule
Suffix
Select a suffix to be added to the file name sent to FTP
server.
None: The name of the sent file will be the Image file
name.
Date & time: The date & time suffix is added to the
Image file name.
Alarm buffer
Select Use alarm buffer when you forward the image/
audio of before and after the alarm detection (pre-alarm,
post-alarm).
If you do not select it, only the image of the moment of
the alarm detection is forwarded.
The date & time suffix consists of lower two-digits of
year (2 digits), month (2 digits), date (2 digits), hour
(2 digits), minute (2 digits) and second (2 digits), and
consecutive number (2 digits), thus 14-digit number
is added to the file name.
Click Alarm buffer to display the Alarm buffer setting
menu.
For details, see “Setting the Alarm Buffer — Alarm
42
Sending Images to FTP Server — FTP client setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and two fixed
digits 00 is added to the Image file name.
Recording Images in
Memory
— Image memory setting Menu
Sequence number clear
Click Clear and the suffix of the sequence number
When you click Image memory on the Advanced mode
menu, the Image memory setting menu appears.
By using the image memory function, you can record the
image and audio file, which has been shot being linked
with the external sensor input or with the built-in motion
detection function, to the built-in memory (about 8 MB)
of the camera. The image file can also be recorded
periodically.
returns to 1.
Interval
Type the interval at which you want to send images to
the FTP server periodically. You can set the hour (H),
minutes (M) and seconds (S) between 1 second and 24
hours (one day).
You can also record a still image periodically.
The recorded image and audio files can be found or
downloaded to the computer using the FTP server
Image memory setting menu is composed of three tabs
Common, Alarm recording and Periodical recording.
Note
The actual interval may be longer than the set value,
depending on the image size, image quality setting, bit
rate and the network environments.
Effective period
Notes
Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the
periodical sending is effective in the schedule setting
in the other section.
• The image and audio files recorded in the built-in
memory will be erased when the power of the camera
is turned off.
• The frame rate and operability on the main viewer
may decrease during image storage in the built-in
memory.
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule —
• When the Overwrite is set to On, a warning mail is not
sent to the Administrator.
OK/Cancel
24.
Common Tab — Setting the Image
memory Function
Image memory
Set whether you use the Image memory function or not.
When you select On, the Common setting options are
displays in the below. If you do not use it, select Off and
click OK.
Free space
Shows the current free space of the builtin memory.
43
Recording Images in Memory — Image memory setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Overwrite
Administrator e-Mail address
Select to overwrite the file or not when there is
insufficient memory space to record the image.
Select On to allow overwriting. The oldest file or folder
is overwritten first.
Type the e-Mail address of the recipient of the warning
mail (e-Mail address of the camera Administrator), up to
64 characters.
Select Off to prohibit overwriting. In this case, a new
file cannot be stored.
OK/Cancel
24.
Capacity warning
Select On to send a warning mail to the Administrator
when the built-in memory space is low or the memory is
full. Select Off if you do not want to send a warning
mail.
Alarm recording Tab — Setting the
Image Memory Function when
Detecting the Alarm
You can set to record the image and audio file to the
built-in memory linked with the external sensor input or
with the built-in motion detection function.
Note
When the Overwrite is set to On, a warning mail is not
sent to the Administrator.
SMTP server name
Type the name of the SMTP server you want to use for
sending the warning mail, up to 64 characters.
Otherwise type the IP address of SMTP mail server.
Authentication
Select the authentication required when you send an e-
Mail.
Off: Select if no authentication is necessary when an e-
Mail is sent.
On: When authentication is necessary an e-Mail is sent,
select one of the authentication methods from the
followings..
SMTP: Select if authentication is necessary when an
e-Mail is sent.
Alarm recording
POP before SMTP: Select when POP before
SMTP is necessary when an e-Mail is sent.
Select On to set to record the image and audio file to the
built-in memory linked with the external sensor input or
with the built-in motion detection function.
Note
When you set to On, make sure to select either or both
SMTP or/and POP before SMTP.
Image file name
Type the file name you want to assign to the images
when saving in the built-in memory. You can use up to
10 alphanumeric characters, - (hyphen) and _
(underscore) for naming.
POP server name
This is necessary when POP before SMTP is selected
in Authentication.
Type POP (receiving mail) server name up to 64
characters. Otherwise type the IP address of POP server.
This setting is necessary when SMTP server that sends a
mail authenticates using the account of POP user.
Suffix
Select a suffix to add to the file name.
Date & time: The Date & time suffix is added to the
Image file name.
The Date & time suffix consists of lower two-digits
of year (2 digits), month (2 digits), date (2 digits),
hour (2 digits), minute (2 digits), second (2 digits)
and consecutive number (2 digits), thus 14-digit
number is added to the file name.
User name, password
Type the user name and the password of the user who
has the mail account. This setting is necessary when
SMTP server that sends a mail authenticates.
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and an
44
Recording Images in Memory — Image memory setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
consecutive 2 digits number is added to the Image
file name.
Periodical recording Tab — Setting
the Periodical recording mode
You can set to record the image file to the built-in
memory periodically.
Tip
A consecutive number added to Date & time and
Sequence number is used to identify each of multiple
files created with one alarm event.
Sequence number clear
Click Clear to reset the Sequence number suffix to 1.
Alarm
Select the connected alarm.
Sensor input: The external sensor which is connected to
the sensor input of the camera I/O port.
Motion detection: Click Motion detection button, and
the Motion detection setting page is displayed. You
can set the motion detection function (page 52).
Note
Periodical recording
Select On when you want to use periodical recording. If
you select Off, the Periodical recording is not executed.
Motion detection works only when the Video mode is
set to MPEG4 and the Cropping is set to Off.
Effective period
Image file name
Set the period when the alarm detection is effective.
Always: The alarm detection is always effective.
Schedule: You can specify the period when the alarm
detection is effective in the schedule setting in the
other section.
Type the file name of the image recorded to the built-in
memory up to 10 alphanumeric, - (hyphen) and _ (under
score).
Note
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule —
You cannot send the audio file by using the periodical
recording function.
Alarm buffer
Suffix
Select Use alarm buffer when you forward the image/
audio of before and after the alarm detection (pre-alarm,
post-alarm).
If you do not select it, only the image of the moment of
the alarm detection is forwarded.
Select a suffix to add to the file name.
None: The recording file name will be the Image file
name.
Date & time: The date & time suffix is added to the
Image file name.
The date/time suffix consists of lower two-digits of
year (2 digits), month (2 digits), date (2 digits), hour
(2 digits), minute (2 digits), second (2 digits), and
consecutive number (2 digits), thus 14-digit number
is added to the file name.
Click Alarm buffer to display the Alarm buffer setting
menu.
For details, see “Setting the Alarm Buffer — Alarm
Sequence number: A consecutive number of 10 digits
between 0000000001 and 4294967295 and two fixed
digits 00 is added to the Image file name.
OK/Cancel
24.
Sequence number clear
Click Clear and the suffix of the sequence number
returns to 1.
45
Recording Images in Memory — Image memory setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Interval
About the extension of a file
Type the interval at which you want to record an image
in the built-in memory periodically. You can set the hour
(H), minutes (M) and seconds (S) between 1 second and
24 hours (one day).
A file to be recorded/sent using the image memory
function or the FTP client function has one of the
following three extensions depending on the video mode
setting and the recording/sending settings of the camera.
.m4f: Represents the MPEG4 video mode.
.jpf: Represents the JPEG video mode when Use alarm
buffer is checked in the alarm recording/alarm
sending menu. This file includes audio data.
.jpg: Represents the JPEG video mode when Use
alarm buffer is not checked in the alarm recording/
alarm sending menu. This file can be viewed with a
normal image viewer.
Note
The actual interval may be longer than the set value,
depending on the image size or the network
environments.
Efective period
Set the period when the periodical recording is effective.
Always: The periodical recording is always effective.
Schedule: You can specify the period when the
periodical recording is effective in the schedule
setting in the other section.
“.m4f” and “.jpf” files.
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule — Schedule
OK/Cancel
24.
Directory Structure of Image
Memory
The images are recorded in the memory with the
following directory structure.
FTP root
Date_No.
Date_No.
xxxxxxx.m4f
yyyyyyy.m4f
aaaaaaa.jpg
bbbbbbb.jpf
ccccccc.mf4
zzzzzzz.mf4
qqqqqqq.mf4
A
represents a directory created automatically.
The Date_No. directory has a 7-digit name consisting of
the last two digits of year (2 digits), month (2 digits),
underscore and sequence number (2 digits).
A directory can contain video files of up to
approximately 1 MB, and a new directory will be
created automatically if the size of the video files in the
current directory exceeds the maximum size, and
recording will continue.
46
Recording Images in Memory — Image memory setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading Images
from the Camera — FTP
server setting Menu
When you click FTP server on the Administrator menu,
the FTP server setting menu appears. Use this menu to
set up for the FTP server function which finds a
specified image and audio file stored in the built-in
memory of the camera (about 8 MB) or download the
still image file from the camera.
Setting the Alarm Output
— Alarm output setting Menu
When you click Alarm output on the Administrator
menu, the Alarm output setting menu appears.
You can set in this menu to control the alarm out of I/O
port on the rear of the camera linked to the alarm
detection, the timer and day/night.
Alarm out 1, 2 Tab
FTP server function
To activate the FTP server function, select On and click
OK.
When you do not use the FTP server function, select Off
and click OK.
Alarm output
To activate the Alarm output function, select On. The
basic setting options are displayed below.
When you do not use the Alarm output function, select
Off.
OK/Cancel
24.
Mode
Select the mode of the Alarm output function.
Alarm: Controls alarm output by synchronizing with an
external sensor input or the built-in activity detection
function.
Timer: Controls alarm output by the timer.
Day/Night: Controls the alarm output linked to the day/
night function.
Note
Note the followings when you log in the FTP server of
the camera using the FTP client software of the
computer.
• The frame rate and the operativity of the monitor
window in the main viewer will degrade.
• While recording the image using the Image memory
function, you cannot delete the recording directory.
• When the recorded image or audio file is deleted, the
camera counts the free space of the built-in memory
again at logging off.
Alarm
This item is displayed when Mode is set to Alarm.
Select the alarm to link the alarm output function. If the
selected alarm is detected, the alarm output status
changes.
Sensor input: External sensor connected to sensor input
of the camera I/O port
Motion detection: To set the motion detection function,
click Motion detection. The Motion detection
47
Downloading Images from the Camera — FTP server setting Menu / Setting the Alarm Output — Alarm output setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Setting the Operations
from the Viewer Page —
Trigger setting Menu
The motion detection function can activate or be set only
when the Video mode of the camera is set to MPEG4
and the Cropping is set Off.
Alarm duration
Select the duration for which the alarm output is short-
circuited between 1 and 60 sec.
Click Trigger on the Administrator menu to display the
Trigger Setting menu.
You can set the activities of when you click
icon of the main viewer in this menu.
Trigger
Effective period
This item is displayed when Mode is set to Alarm.
Set the period while the alarm detection is effective.
Always: The alarm detection is always effective.
Schedule: You can specify the period when the alarm
detection is effective in the schedule setting in the
other section.
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule — Schedule
Schedule
This item is displayed when Mode is set to Timer.
Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule — Schedule
e-Mail (SMTP)
After checking it, you will be able to select e-Mail in the
Trigger setting menu. You can send mail with attached
image file by selecting e-Mail and clicking the Trigger
icon.
When you click e-Mail (SMTP) button, the Trigger (e-
Mail) setting menu is displayed. You can set necessary
options here. The setting options and setting procedures
are the same as those of the e-Mail (SMTP) setting menu
OK/Cancel
24.
48
Setting the Operations from the Viewer Page — Trigger setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Image memory
Note
After checking this, you will be able to select Image
memory in the Trigger setting menu. You can record an
image file to the built-in memory by selecting Image
memory and clicking the Trigger icon.
While the Video mode is set to MPEG4, the image of
the composite video signal output from the video output
connector of the camera may be distorted during mail
transmission.
When you click Image memory button, the Trigger
(setting) Image memory menu is displayed. You can
set necessary options here. The setting options and
setting procedures are the same as those of the Image
FTP client
After checking this, you will be able to select FTP client
in the Trigger setting menu. You can send an image file
to FTP server by selecting FTP and clicking the Trigger
icon.
Alarm output 1, 2
After checking this, you will be able to select Alarm
output 1 or Alarm output 2 in the Trigger setting menu.
You can control On (short circuit ) or Off (open) by
selecting Alarm output and clicking the Trigger icon.
When you click FTP client button, the Trigger (setting)
FTP client menu is displayed. You can set necessary
options here. The setting options and setting procedures
are the same as those of the FTP client setting menu
Day/Night
After checking it, you will be able to select day/night in
the Trigger setting menu. You can control On (night
mode) or Off (day mode) of the day/night function by
clicking the Trigger icon.
When you click the day/night button, the day/night
setting (Trigger) menu is displayed. You can set the
necessary options here. The setting options and setting
49
Setting the Operations from the Viewer Page — Trigger setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
procedures are the same as those of the Camera setting
menu (page 28).
Setting the Schedule
— Schedule setting Menu
When you click Schedule on the Administrator menu,
the Schedule setting menu appears.
This is the same menu as the setting menu which is
displayed when you click Schedule to set Effective
period and Schedule in FTP client setting menu, e-Mail
(SMTP) setting menu, Image memory setting menu,
Alarm output 1, 2 setting menu and so on.
Example: When setting e-Mail (SMTP) (the alarm
sending) in the Schedule setting menu
Note
The day/night function is invalid when its mode is set to
Disable or Auto in the day/night tab even when you
select day/night in the Trigger setting menu.
OK/Cancel
24.
Schedule selection
Select the list box to specify the schedule you want to
set. e-Mail (SMTP) – Alarm, e-Mail (SMTP) –
Periodical, FTP – Alarm, FTP – Periodical, Image
memory – Alarm, Image memory – Periodical,
Alarm output 1 – Alarm, Alarm output 1 – Timer,
Alarm output 2 – Alarm or Alarm output 2 – Timer
can be selected.
The time period on the right of the checked day is the
effective period of the schedule.
Mon (Monday) to Sun (Sunday)
The time period on the right of the checked day is the
effective period of the schedule.
Start time, Stop time
Specify the Start time and the Stop time.
Use the same time schedule every day
When this is checked, the Start time and Stop time set to
Mon (Monday) are applied to all days. In this case, the
Start time and Stop time of the other days than Mon
(Monday) cannot be input.
OK/Cancel
24.
50
Setting the Schedule — Schedule setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Setting the Alarm Buffer
— Alarm buffer setting Menu
The value of Recording capacity differs depending on
Image size, Bit rate (for MPEG4) and Image quality (for
JPEG) in the camera setting menu.
When you click Alarm buffer on the Administrator
menu, the Alarm buffer Setting menu appears.
You can set the Pre-alarm image and audio (the image
and audio before the alarm detection) and the Post -
alarm image and audio. These can be set when Alarm
sending or Alarm recording of FTP client setting menu
or Image memory setting menu is set to On, and besides
when Use alarm buffer is selected.
OK/Cancel
24.
Video mode
The Video mode set in the Common tab of the Camera
setting menu is displayed.
MPEG4: Shows the present output format of the camera
is MPEG4.
JPEG: Shows the present output format of the camera is
JPEG.
Recording capacity
Displays the maximum recording capacity of alarm
buffer in the present camera setting of the video mode,
image size, bit rate and frame rate.
Pre-alarm period: Displays the maximum recording
capacity of image/audio before the alarm detection.
Post-alarm period: Displays the maximum recording
capacity of image/audio after the alarm detection.
Recording time
Set the recording time for the Pre-alarm image/audio
and Post alarm image/audio.
Pre alarm period: Type the recording time of the
image/audio before the alarm detection.
Post alarm period: Type the recording time of the
image/audio after the alarm detection.
51
Setting the Alarm Buffer — Alarm buffer setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Motion detection indicator
The moving level of the present shooting image inside
the specified Window is shown in the graph. The even
line shows the threshold level for Motion detection
which will be a guide to set the sensitivity properly.
Setting the Motion
Detection Function —
Motion detection setting Menu
When you click Motion detection on the Administrator
menu, the Motion detection setting menu appears.
You can set the conditions to activate the built-in motion
detection function in this menu.
This is the same menu with the setting menu which is
displayed when you click Motion detection in Alarm
sending of e-Mail (SMTP) setting menu, Alarm sending
of FTP client setting menu, Alarm recording of Image
memory setting menu and so on.
Sensitivity slider bar
Use it to set the detection sensitivity of the monitoring
image.
When the slider bar is moved to the left end, the
sensitivity will be 0 and any motion will not be detected.
The right end is the maximum sensitivity.
Setting the Motion Detection Area,
Sensitivity and Threshold level
Set the motion detection working area, the sensitivity
and the threshold level as follows:
Note
The motion detection function can activate or be set only
when the Video mode of the camera is set to MPEG4
and the Cropping is set Off.
1
2
Check Window 1 check box.
Window 1 is shown on the monitor display.
Settle Window 1 in the area you want to set Motion
detection.
Click and drag Window 1 to move it or change the
size of it.
3
Set the Sensitivity of Motion detection.
Adjust it referring to the level indicator of Motion
detection.
To increase the sensitivity, move the Sensitivity
slider bar to the right.
To decrease, move it to the left.
When you release the mouse, the new setting is
applied to the level of motion detection indicator.
The Motion detection setting menu is composed of the
following five parts.
4
Set the Threshold level of Motion detection.
Adjust the Threshold slider bar in the same way of
step 3 to set the level the camera executes motion
detection.
Monitor display
You can monitor the moving image and sets the
detection window.
5
6
If necessary, set the Motion detection working
areas, the sensitivities and the Threshold level of
the other Windows 2, 3, 4 by following steps 1 to 4.
Window 1 to 4 check box
When you check it, the specified Window is displayed
on the monitor display.
After all settings, click OK.
Notes
Threshold slider bar
• While motion detection setting menu is displayed,
motion detection e-Mail (SMTP) notification, FTP
client, Image memory and Alarm output function will
not work. Make sure to close Motion detection setting
menu after setting.
Set the Threshold level so as to judge whether there has
been any motion in the camera image or not. You can
change the Threshold level displayed in the Motion
detection indicator.
• Before using the Motion detection, perform the
operation test to confirm correct operation.
52
Setting the Motion Detection Function — Motion detection setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
• The Motion detection may not operate correctly in the
following cases:
– while changing a setting on the Camera setting
menu
– when the object is dark
– when the camera is installed in an unstable place
that causes vibration to the camera
– when a small bit rate (64 kbps, 128kbps) is selected
in Bit rate setting of MPEG4
53
Setting the Motion Detection Function — Motion detection setting Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
The current bandwidth is displayed in Current
bandwidth.
Others
This section explains how to use the application
software and commands, including the supplied CD-
ROM.
Using the Supplied
Setup Program
Explains the functions except the Network tab in the
Setup Program.
To install the Setup Program, to assign the IP address
and to set the network, see “Assigning the IP address to
Starting the Setup Program
Select Program from Start menu of Windows, then
select Program, IP Setup Program and IP Setup
Program in sequence.
2
3
4
5
Click to select the camera to set the bandwidth from
the list box.
The IP Setup Program starts.
Network tab appears. The IP Setup Program detects
cameras connected to the local network and lists them
on the Network tab window.
Click to select the desired bandwidth from the
Setting bandwidth list box.
Type the Administrator name and Administrator
password in each box.
Bandwidth Control Tab
The communication bandwidth can be set when the
Video mode of the camera is set to JPEG.
Click OK.
If “Setting OK” is displayed, the bandwidth setting
is completed.
Note
When the Video mode of the camera is set to MPEG4,
the bandwidth cannot be changed.
1
Click the Bandwidth control tab to display the
bandwidth setting window.
54
Using the Supplied Setup Program
Download from Www.Somanuals.com. All Manuals Search And Download.
Date time Tab
Note
Due to network properties, there may be a slight
difference between the displayed computer's date and
time and those set on the camera.
You can set the date and time on the camera.
1
Click the Date time tab to display the date/time
setting window.
PPPoE Tab
PPPoE is used to connect to an ISP (Internet Service
Provider) via the Internet. Using PPPoE, you can
automatically obtain an IP address to connect to the
Internet from the ISP.
The following PPPoE setting items are provided for the
SNC-DF70N/DF70P.
• User ID assigned by your ISP
• Password for the user ID
• DNS setting (automatic/manual setting)
1
Click the PPPoE tab to display the PPPoE setting
window.
2
Click to select the camera you want to set the date
and time for.
You can select multiple cameras and set the date
and time simultaneously.
3
4
5
Select the date/time format from the Date time
format drop-down list.
Select the area where the camera is installed from
the Time zone selecting drop-down list.
Set the date and time.
You can set the date and time in two ways.
Manual current date time setting
Set the current date and time on the Manual
current date time setting boxes, and click OK.
The setting boxes are for the year (last two digits),
month, date, hour, minutes and seconds from left to
right.
2
3
Click to select the camera you want to make the
PPPoE settings for.
Select On below the list to enable the PPPoE
setting.
PC current date time setting
The date and time set on the computer is displayed
in the PC current date time setting box.
Click OK on the right to set the camera’s date and
time to the displayed computer's date and time.
To disable the PPPoE setting, select Off.
4
5
Type the user ID assigned by the ISP in the User ID
box.
Type the password for the user ID in the Password
box.
55
Using the Supplied Setup Program
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Retype the password for the user ID in the Re-type
password box.
Using the SNC audio
upload tool — Transmitting
Audio to Camera
Set the DNS server address.
To obtain the DNS server addresses
automatically:
Select Obtain DNS server address automatically.
The supplied SNC audio upload tool allows you to
transmit sound from the computer to the camera.
This section explains the setup and operations of the
SNC audio upload tool.
To specify the DNS server addresses manually:
Select Use the following DNS server address, and
type the Primary DNS server address and
The SNC audio upload tool supports the following audio
data to be transmitted.
Secondary DNS server address in each box.
8
9
Type the Administrator name and Administrator
password in each box.
Audio CODEC
G711 (µ-LAW)
G.726
Transmission rate
64 kbps
Click OK.
If “Setting OK” is displayed, the PPPoE setting is
40 kbps
completed.
G.726
32 kbps
G.726
24 kbps
Rebooting the Camera
G.726
16 kbps
Click Reboot on the Network tab to reboot the camera.
It will take about two minutes to start again.
Note
Only one administrator can transmit sound to the
camera. Meanwhile, other users with administrator ID
and a password will not be able to transmit sound to the
camera.
Installing the SNC audio upload
tool
1
Insert the supplied CD-ROM disc into your
computer CD-ROM drive.
After a short time a window will open displaying
the files on the CD-ROM.
2
3
Click the Setup icon of SNC audio upload tool.
The “File Download” dialog opens.
Click Open.
Note
If you click “Save this program to disk” on the “File
Download” dialog, you cannot install correctly.
Delete the downloaded file, and click Setup icon
again.
4
Install the SNC audio upload tool following the
wizard displayed.
If the Software License Agreement is displayed,
read it carefully and accept the agreement to
continue the installation.
56
Using the SNC audio upload tool — Transmitting Audio to Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Camera to the
Computer
Using the SNC audio upload tool
When you start the SNC audio upload tool, the
following window is displayed.
1
2
Connect a speaker to the line output jack on the
camera.
Menu tab
Connect a microphone to the microphone input jack
on the computer.
Note
If the microphone input jack of the computer is not set
correctly, no sound is transmitted from the computer and
nothing is output from the speaker connected to the
camera.
Set the microphone input jack from the control panel of
Windows.
On Windows 2000
1 Select Sounds and Multimedia from Control Panel.
2 Click Volume in the Sound Recording section on
the Audio tab.
The Recording Control window opens
3 Check Select in the Microphone section.
On Windows XP
N (start)/x(stop)
Click N (start) to start sound transmission. The
transmission speed is displayed in the Bitrate box during
transmission. You can adjust the microphone volume
and enable/disable the muting, if necessary.
1 Select Sounds and Audio Device from Control
Panel.
2 Click Volume in the Sound Recording section on
the Audio tab.
To stop the sound transmission, click x(stop).
The Recording Control window opens.
Note
3 Check Select in the Microphone section.
If you change IP Address, Proxy Port, CODEC on the
Setting tab during the sound transmission, the changed
settings will be effective after the transmission.
Sound adjustment and indicators
Adjust the microphone input volume by moving the
slider bar. You can adjust the volume even
during the transmission.
Click the
microphone icon to enable/disenable the
sound muting.
The transmission rate is displayed in the Bitrate box.
The microphone input volume is displayed at the Level.
57
Using the SNC audio upload tool — Transmitting Audio to Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting tab
Using the SNC video
player — Playing Video/
Audio File Recorded on
Camera
The supplied SNC video player allows you to play
video/audio data recorded on the camera with your
computer.
This section explains the setup and operations of the
SNC video player.
Downloading the SNC video player
To download the SNC video player, click the
Player
icon located on the upper part of the main viewer of the
camera.
Input the Administrator name and Administrator
password on the download dialog.
Note
User
To operate the SNC video player, a special DLL file is
necessary. This file is automatically installed in the
computer when you view camera images with the
ActiveX viewer.
Set the User ID and Password for the administrator.
The default setting of the User ID for the Administrator
is “admin,” and the Password is “admin.”
Camera address
Type the IP address or host name of the camera you want
to transmit sound.
Using the SNC video player
1
Double-click the SNC video player downloaded
from the camera to start this application.
Camera port
Set the port of the camera you want to transmit sound.
The default port is “HTTP” (80).
CODEC
Select the audio mode (CODEC) from the drop-down
list.
2
3
Click the
The Select File dialog opens.
icon.
Select the file you want to play.
58
Using the SNC video player — Playing Video/Audio File Recorded on Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
Information boxes on the selected file are displayed
on the left side of the window as follows:
Using the Custom
Homepage Installer
You can store the homepage that you have created in the
camera and watch it.
Each click on the
(information) icon switches
between “display” and “Not to display” of the file
information.
Model name: Model name of the camera with
which the file is recorded.
IP address: IP address of the camera with which
the file is recorded.
Serial number: Serial number of the camera with
which the file is recorded.
Record event: Type of event used for the
recording: Sensor input, Periodical, Motion
detection or Manual.
Date&time: Recording date and time
Movie: Video CODEC
Notes on creating the homepage
When you creating the homepage, note the following
points.
• The file name should be typed up to 24 characters
including the extension.
• The file size of the homepage should be 2.4 MB or
less.
• To watch the created homepage, set the Default URL
in the System setting menu.
Audio: Audio CODEC
Playing a video/audio file
Uploading the Custom Homepage
Installer to the Camera
Click
(start) to start playing from the beginning of
the selected file.
To freeze the movie temporarily, click
(pause).
Click
again to restart playing.
1
2
After a short time a window will open displaying
the files on the CD-ROM.
To stop playing, click
To restart playing, click
Play stops when the file is played to the end.
(stop).
(start) again.
Click the Setup icon of Custom Homepage
Installer.
The “File Download” dialog opens.
To play from a specified point
Move the slider bar below the image display, and
playing starts according to the slider bar position.
3
Click Open.
The installer starts and notes are displayed.
Adjusting the sound
Adjust the playing sound volume by moving the
slider bar. Move it to the left end for the
minimum volume, and to the right end for the maximum
volume.
Click the speaker icon to enable/disable the sound
muting.
When the sound muting is on, no sound is heard even if
you move the slider bar to the right.
Saving an image
Click
(capture) icon during playing or pause and the
captured image is displayed on a pop-up dialog. To save
the image, click Save on the dialog. You can specify the
destination to which the image is to be stored and select
the JPEG or Bitmap format.
Note
If you click “Save this program to disk” on the “File
Download” dialog, the
CustomHomepageInstaller.exe file will be saved on
the computer. Double-click the saved file to start it.
59
Using the Custom Homepage Installer
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Read the notes carefully, and click Next>.
The Software License Agreement is displayed.
When using an HTTP proxy server:
Select Use HTTP proxy server, and type your
settings in the Proxy server address and Proxy
server port No. boxes.
When using an FTP proxy server:
Select Use FTP proxy server, and type your
settings in the Proxy server address and Proxy
server port No. boxes.
Note
If you cannot establish communication with the
camera with the proxy server being used, connect
the camera to the local network and run the installer
without using the proxy server.
9
Type the Administrator name and Administrator
password of the camera to be uploaded.
10 Confirm that all items are correct, then click Next.
5
Read the agreement carefully, select Agree if you
accept it, then click Next.
11 Type the path for the folder in which your
homepage is stored in the Source folder box, then
click Next.
6
7
8
Type the IP address of the camera to be uploaded in
the IP address box.
Specify the HTTP port No. of the camera.
Initial HTTP port No is set to 80.
When you use a proxy server, set the following:
For the proxy server of your environments, consult
your network administrator.
12 Click OK.
Uploading of the homepage file starts.
60
Using the Custom Homepage Installer
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Assigning the IP
Do not turn off the camera until the camera is
rebooted after uploading the homepage file.
Address to the Camera
Using ARP Commands
This section explains how to assign an IP address to the
camera using ARP (Address Resolution Protocol)
commands without using the supplied setup program.
Note
Enter the ARP commands within 5 minutes of the power
of the camera being turned on.
1
2
Open the DOS window on the computer.
Enter the IP address and the MAC address of the
camera to assign a new IP address, using the
following ARP commands.
arp -s <Camera's IP address> <Camera's MAC address>
ping -t <Camera's IP address>
The following page will appear after a while.
Example:
arp -s 192.168.0.100 08-00-46-21-00-00
ping -t 192.168.0.100
3
When the following line is displayed on the DOS
window, hold down Ctrl and press C.
Reply from 192.168.0.100:bytes=32 time...
You will normally receive a reply after about 5
repetitions of "Request time out."
Note
If you do not receive a reply, check the following:
– Did you enter the ARP commands within 5 minutes of
the camera being turned on?
If not, turn off the camera and restart the operation.
– Is the NETWORK indicator on the camera flashing?
If the indicator goes off, the network connection has a
problem. Connect the network correctly.
– Did you enter the IP address previously used for
another device?
After displaying this page, the camera will be
adjusted and rebooted automatically in two
minutes.
Assign a new IP address to the camera.
– Do the computer and the camera have the same
network address?
13 Click Finish to exit the program.
If not, set the same network address on the computer
and the camera.
61
Assigning the IP Address to the Camera Using ARP Commands
Download from Www.Somanuals.com. All Manuals Search And Download.
4 describesthecaseof“mib-2.system.sysContact.0”.
This field is used to describe the information on
administrator of this camera. Nothing is set at the
factory.
Using the SNMP
This unit supports SNMP (Simple Network
Management Protocol). You can read MIB-2 objects
and write some MIB-2 objects using software such as
SNMP manager software. This unit also supports the
coldStart trap which occurs when the power is turned on
or the unit restarts, and the Authentication failure trap
which informs of an illegal access using SNMP.
Using CGI commands, you can set community name
and access limitation, reading/writing right, host to send
traps, and some MIB-2 objects. To allow these settings,
you need authentication by the camera administrator.
5 describes the case of “mib-2.system. sysName.0”.
This field is used to describe administration mode
of this camera. Nothing is set at the factory.
6 describes the case of “mib-2.snmpEnable
AuthenTraps.0”. This example shows when “1”
(enable) is set. With this setting, a trap occurs when
there is an Authentication failure. When “2”
(disable) is set, no Authentication failure trap
occurs.
7 describes the community name and the reading/
writing attributes. This example shows the
identification number “ID=1”, the community
name public, and enables read from any IP address
(0.0.0.0).
1. Inquiry Commands
You can check the SNMP Agent settings using the
following CGI commands.
<Method>
GET, POST
<Command>
8 describes the community name and the reading/
writing attributes, similarly to 7. This example
shows the identification number ID=2, the
community name “private”, and enables “read/
write” by the SNMP request packet from the host
“192.168.0.101”.
(JavaScript parameter format)
(standard format)
With the above inquiry, you can obtain the following
setting information. The following explains the setting
information using the inqjs=snmp (JavaScript
parameter) format.
9 describes the host name to send a trap. This
example shows the identification number “ID=1”,
the community name “public”, and enables sending
of traps to the host having the IP address
“192.168.0.101”.
var sysDescr=“\“SONY Network Camera SNC-
DF70\””
...1
...2
...3
...4
...5
...6
...7
var sysObjectID=“1.3.6.1.4.1.122.8501”
var sysLocation=“\“\””
var sysContact=“\“\””
var sysName=“\“\””
var snmpEnableAuthenTraps=“1”
var community=“public,0.0.0.0,read,1”
2. Setting Commands
The unit supports the following setting commands of
SNMP.
<Method>
GET, POST
<Command>
var community=“private,192.168.0.101,write,2” ...8
var trap=“public,192.168.0.101.1” ...9
<parameter>=<value>&<parameter>=...&...
1 describes the case of “mib-2.system. sysDescr.0”.
First, perform the settings of the following parameters.
You cannot change this parameter.
1) sysLocation=<string>
2 describes the case of “mib-2.system.
Set the case of “mib-2.system.sysLocation.0” in the
<string> position. The maximum length of
<string> is 255 characters.
sysObjectID.0”. You cannot change this parameter.
3 describes the case of “mib-2.system.
sysLocation.0”. This field is used to describe
information on the location of this camera. Nothing
is set at the factory.
2) sysContact=<string>
Set the case of “mib-2.system.sysContact.0” in the
<string> position. The maximum length of
<string> is 255 characters.
62
Using the SNMP
Download from Www.Somanuals.com. All Manuals Search And Download.
3) sysName=<string>
Set the case of “mib-2.system.sysName.0” in the
<string> position. The maximum length of
<string> is 255 characters.
4) enaAuthTraps=<value>
Set the case value of “mib-2.snmp.snmp
EnableAuthenTraps.0”. Type “1” (enable) or “2”
(disable) in the <value> position.
5) community=<ID>,<rwAttr>,
<communityName>,<IpAddressString>
Set the community name and the reading/writing
attributes. <ID> describes the setting identification
number (1 to 8), <rwAttr> describes a character
representing the reading/writing attribute (“r”, “R”,
“w or “W”), <communityName> describes the
community name to be set, and <IpAddressString>
describes the IP address of the host you allow
access (0.0.0.0 for any host).
Example: To allow reading/writing by any host in the
“private” community and having the ID number “2”.
community=2,w,private,0.0.0.0
6) trap=<ID>,<communityName>,
<IpAddressString>
Set the host you want to send traps to. <ID>
describes the setting identification number (1 to 8),
<communityName> describes the community
name to send traps to, and <IpAddressString>
describes the IP address of the host to send traps to.
Example: To specify the destination of traps as the
private community and the ID number “1”.
rap=1,public,196.168.0.101
7) delcommunity=<ID>
This parameter is used to delete the previous
community setting. <ID> describes the community
setting identification number (1 to 8).
8) deltrap=<ID>
This parameter is used to delete the previous setting
of the host to send traps to. <ID> describes the trap
setting identification number (1 to 8).
When you have finished changing the SNMP setting
information using the above parameters 1) to 8), check
the changed settings using an inquiry commands. If the
changed settings are OK, restart the SNMP using the
following CGI command.
SNMP restart command
<Method>
GET, POST
<Command>
snmpd=restart
63
Using the SNMP
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera
Image device NTSC
Specifications
1/4 type interline transfer (Super
HAD CCD), 380,000 picture
elements
PAL
System/network
Protocol
TCP/IP, ARP, ICMP, HTTP, FTP
1/4 type interline transfer (Super
HAD CCD), 440,000 picture
elements
(server/client), SMTP (client),
DHCP (client), DNS (client), NTP
(client), SNMP (MIB-2), RTP/
RTCP, PPPoE
Effective picture elements
NTSC
768 (horizontal) × 494 (vertical)
PAL
752 (horizontal) × 582 (vertical)
CS mount
Signal format NTSC/PAL
VBS: within 1.0 Vp-p 5%, 75 ohms,
sync negative
NTSC
525 lines, 2:1 interlace
PAL
625 lines, 2:1 interlace
Compression
Video compression format
MPEG4/JPEG
Audio compression format
G.711/G.726 (40, 32, 24, 16 kbps)
640 × 480, 480 × 360, 384 × 288, 320
× 240, 256 × 192, 160 × 120
Maximum frame rate
MPEG4:30 fps (QVGA)
Lens mount
Image size
Scanning
JPEG:30 fps (QVGA)
Web browser Internet Explorer Ver. 5.5 or 6.0
(Available OS: Windows 2000/ XP)
Computer environments
CPU: Pentium III, 1GHz or higher
(Pentium 4, 2 GHz or higher
recommended)
RAM: 256 MB or more
Display size: 1024 × 768
Maximum user access
Synchronization
INT only
Horizontal resolution
480 TV lines (analog video)
Signal-to-noise ratio
50 dB (AGC OFF, Weight On) (analog
video)
Minimum illumination
0.9 lux (AGC ON, F1.0)
On/Off switchable
AGC
Exposure control
MPEG4 mode: 10 users
JPEG mode: 20 users
Network security
AUTO iris
CCD Iris
Electronic shutter
Password (basic authentication), IP
filtering
White balance ATW
BLC
Other functions
On/Off switchable
Activity detection, image trimming,
built-in clock, etc.
Interface
Network port 10BASE-T/100BASE-TX (RJ-45)
I/O port
9 pin Mini DIN connector
Sensor input : make contact
Alarm output 1 and 2: 24 V AC/DC,
max., 1 A
(mechanical relay outputs
electrically isolated from the
camera)
Day/Night control input: ×1, 5 V DC
input
Day/Night control output: ×1, 5 V DC
output
Auto iris lens connector
DC servo
64
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Video output
BNC connector, 1.0 Vp-p,
75 ohms, unbalanced, sync negative
Monitor output
2 Pin connector, 1.0 Vp-p, 75 ohms,
unbalanced, sync negative
Microphone input
Sensitivity: -40 3.5dB
Freguency range: 50-15,000Hz
5
Plug: φ3.5mm ( /32 inches), Mini-plug,
plug-in power system
Line output
Type: Active speaker
Input impedence: 4.7 kohms or more
5
Plug: φ3.5mm ( /32 inches), Mini-plug
Others
Power supply 24 V AC 10% 50/60 Hz, 12 V DC
10%, PoE
Power consumption
8 W max.
Operating temperature
–10 °C to 50 °C (14 °F to 122 °F)
Storage temperature
–20 °C to 60 °C (–4 °F to 140 °F)
Operating humidity
20 to 80 %
Storage humidity
20 to 95 %
Dimensions
135 × 164.5 × 166.1 mm
(5 /8 × 6 /2 × 6 /8 inches)
Approx. 1.8 kg (3 lb 11 oz)
3
1
5
Mass
Supplied accessories
CD-ROM (setup program and User’s
Guide) (1)
Monitor cables (1)
Screws (4)
Wrench (1)
I/O extension cable (1)
Wire rope (1)
Installation Manual (this document)
(1)
B&P Warranty Booklet (for SNC-
DF70N only) (1)
Design and specifications are subject to change without
notice.
65
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
DHCP .............................................32
DNS server .....................................33
Dynamic IP address notification ....34
L
Index
loading the setting data...................27
logging in........................................14
A
M
main viewer page............................16
memory...........................................43
menu section...................................16
monitor Image ................................17
monitor image section ....................17
Motion detection setting Menu.......52
E
e-Mail .............................................24
e-Mail (SMTP) ...............................24
e-Mail (SMTP) setting Menu .........38
e-Mail address ................................35
F
Factory default................................27
factory settings ...............................27
flash memory..................................25
format of date and time ..................26
free space........................................44
FTP client setting Menu .................41
FTP server setting Menu ................47
N
network configuration ....................32
O
B
overwrite.........................................44
H
P
Home ..............................................16
HTTP port number .........................10
Password.........................................36
Periodical recording .......................45
periodical recording........................45
Picture.............................................29
Player..............................................16
port number ....................................33
PPPoE.............................................55
C
I
Image memory setting Menu..........43
Image size.......................................28
Internet Explorer ............................11
IP Address ........................................9
R
recording images ............................43
reset ................................................32
J
D
Java applet viewer ..........................15
S
saves the setting data ......................27
66
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
Schedule setting Menu................... 50
Security .......................................... 24
security........................................... 24
security setting ............................... 37
Security setting Menu .................... 37
sending images............................... 41
serial number.................................. 25
Setting ............................................ 16
SMTP server .................................. 34
SNC audio upload tool................... 56
SNC video player........................... 58
SNMP............................................. 62
Software version ............................ 25
subnet mask.................................... 32
system configuring......................... 25
System log...................................... 27
User name ...................................... 36
user name ....................................... 36
user setting ..................................... 36
V
viewer............................................. 15
Viewer mode .................................. 36
volume............................................ 17
W
T
TCP ................................................ 21
time difference ............................... 26
Time zone....................................... 26
time zone........................................ 26
title ................................................. 35
title bar ........................................... 25
Title bar name ................................ 25
Trigger setting Menu...................... 48
U
UDP (Multicast)............................. 21
UDP (Unicast)................................ 21
URL ............................................... 25
Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sennheiser Microphone E 904 User Manual
Shure Headphones 515SBGX User Manual
SIIG Switch ID US0011 S1 User Manual
Snapper Chipper SG 8000 User Manual
Sony Microcassette Recorder WM GX654 User Manual
Sony Water Dispenser 2 User Manual
Specialized Bicycle Accessories Stumpjumper Adjustable Dropout User Manual
Sportline Marine Sanitation System solo 910 User Manual
Stanley Black Decker Automobile Parts MBX138 User Manual
Stanton CD Player C313 User Manual