Sony Projection Television KDP 51WS655 User Manual

2-148-833-01(1)  
Connecting  
Your Projection TV  
Running  
Initial Setup  
3
4
Review the following chart to determine which diagram to use to  
connect the components in your system:  
After you finish connecting the TV, you need to run Initial Setup,  
which automatically creates a list of available analog and digital  
channels. The Initial Setup screens appear when you turn on your TV  
for the first time after hooking it up.  
KDP-51WS655, KDP-57WS655  
See  
Reverse  
For these components  
Quick Setup Guide  
1 Press POWER to turn on the TV.  
DVD  
Cable  
Antenna  
Antenna  
VCR  
Player  
The Initial Setup screen appears.  
A
CableCARD  
(optional)  
2 Using the remote control, move the highlight to the desired  
language, then press to select that language.  
The next screen instructs you to connect your cable/antenna.  
Check that you’ve connected your signal source correctly.  
DVD  
Cable  
Cable Box  
AV Receiver  
VCR  
Player  
or  
B
C
To set up your projection TV, follow these steps:  
Satellite Receiver  
DVD  
Cable  
Cable  
Antenna  
Antenna  
Cable Box  
Satellite Receiver  
VCR  
Player  
DVD  
3 To start Auto Program, highlight Yes and then press  
.
HD Cable Box  
or  
AV Receiver  
Digital Recorder  
Player  
D
Auto Program automatically creates a list of receivable analog and  
digital channels. Auto Program may take 50 minutes or more to  
complete. A progress bar is displayed while the channel list is  
being created.  
HD Sat Receiver  
DVD  
Cable  
Cable  
Antenna  
Antenna  
HD Cable Box  
1 2 3 4 5  
E
F
VCR  
Player  
Sony  
Cable Box  
VCR  
Dream System  
or  
The lowest numbered channel is displayed.  
Checking the  
Supplied Accessories  
Carrying the  
Projection TV  
Connecting Your  
Projection TV  
(see reverse side)  
Running Initial Setup  
Adjusting the  
Convergence  
Satellite Receiver  
See the “Cables Required” chart that appears with the diagram to  
determine which cables you’ll need. You may need to purchase  
extra accessories, such as cables and splitters, depending on the  
components you plan to connect.  
If, after reading the Operating Instructions and this Quick  
Setup Guide, you have additional questions related to the  
use of your Sony television, please call our Customer  
Information Services Center at:  
Turn off and unplug all components before making connections.  
If you have a component such as a DVD player that includes a  
DVI video output, you can connect it to the TV’s HDMI input  
using a DVI-to-HDMI cable (and analog audio cables).  
1-800-222-SONY (7669) (US residents only) or  
(416) 499-SONY (7669) (Canadian residents only).  
If you are connecting a digital cable box, you’ll need a special bi-  
directional splitter that’s compatible with your cable box. Contact  
your cable provider for details.  
© 2004 Sony Corporation  
Printed in U.S.A.  
Making Video Connections  
Your TV includes several types of video inputs. Use the inputs that  
are available on your components that provide the best video  
performance, as described below.  
Checking the  
Supplied Accessories  
Carrying the  
Projection TV  
Adjusting the  
Convergence  
The projection tube image appears on the screen in three colors (red,  
green and blue). If the three colors do not project properly, the color is  
poor and the picture blurs. Before you use your TV, be sure to run the  
Flash Focus feature. Flash Focus adjusts the color projection settings  
automatically.  
Best Video Performance  
1
2
5
HDMI (High-Definition Multimedia Interface)  
Along with your new projection TV, the package contains a remote  
control and two AA batteries. No additional cables are included.  
These items are all you need to set up and operate the projection TV  
in its basic configuration.  
Be careful when moving the TV.  
When you place the TV in position, be careful not to drop it on  
your foot or fingers.  
Watch your footing while installing the TV.  
Component video  
S VIDEO  
If you carry the TV in a manner other than the specified manner  
and without the specified number of persons, it may drop and a  
serious injury may be caused. Be sure to follow the instructions  
mentioned below.  
Carrying the TV requires four or more people.  
Do not carry the TV holding the speaker grill.  
Hold the TV tightly when carrying it.  
Composite video  
RF/Coaxial  
Allow the TV to warm up for about 30 minutes before you adjust the  
convergence with Flash Focus.  
Inserting Batteries  
1 Remove the battery cover from the remote control.  
2 Insert two size AA (R6) batteries (supplied) by matching the e  
and E terminals on the batteries to the diagram inside the battery  
compartment.  
Good Video Performance  
1 Tune to a TV or cable TV program.  
2 Press the FLASH FOCUS button on the front panel of the TV.  
The cross pattern appears and Flash Focus begins to work.  
Additional Connections  
For best audio performance, connect your digital audio components  
using either digital optical or digital coaxial audio connections.  
3 Replace the battery cover.  
The TV includes casters. Be sure to move your projection TV  
2
1
using these casters.  
,
If you are using a CableCARD or the digital audio (optical) output connector,  
see the Operating Instructions for details.  
Remove the batteries to avoid damage from possible battery  
leakage whenever you anticipate that the remote control will not  
be used for an extended period.  
Depending on which components are in your system, you may need  
to complete additional connections. For example, if you have a  
satellite receiver, you’ll need to connect the satellite antenna. If you  
have an A/V receiver, you’ll need to connect speakers.  
The adjustment is completed when the TV picture returns.  
To Perform Additional Fine Manual Adjustments  
Use the manual Convergence feature, as described in the  
Handle the remote control with care.  
Operating Instructions.  
Avoid dropping it, getting it wet, placing it in direct sunlight, near  
The connection diagrams shown on the reverse side are recommendations  
only; other possible solutions may exist. Connections that include an A/V  
receiver can often be very complex, so check your A/V receiver’s instruction  
manual for additional details.  
a heater, or where the humidity is high.  
Notes on Flash Focus  
You cannot perform any other functions until Flash Focus has  
completed its cycle. If you perform any other operation while  
Flash Focus is in progress, the Flash Focus operation is canceled.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Headphones SE846 User Manual
SIIG Speaker 04 0600B User Manual
Sonance Speaker Cabinet LCR Speaker User Manual
Sony Car Stereo System XRS 300 User Manual
Sony Stereo Receiver DRC BT30 User Manual
Southern Telecom Camcorder DC14S User Manual
StarTechcom Laptop Docking Station USB3DOCKH2DP User Manual
Sun Microsystems Server V20Z User Manual
SV Sound Car Speaker STA 1000D User Manual
Swann Security Camera DVR4 Net PLUS User Manual