En g lish
Use TYPE I (normal) tape only.
Use TYPE I (normal) tape only.
Dimensions
On o p e ra t io n
•
Ta p e Pla ye r
Approx. 420 × 165 × 256 mm (w/ h/ d)
Pla yin g a t a p e
Re co rd in g
Fa llin g a sle e p t o m u sic
(16 5⁄8 × 6 1⁄2 × 10 1⁄8 inches) (incl.
If the player is brought directly
from a cold to a warm location, or
is placed in a very damp room,
moisture may condense on the
lenses inside the CD player
section. Should this occur, the
player will not operate properly.
In this case, remove the CD and
wait about an hour for the
moisture to evaporate.
Pre ca u t io n s
Troubleshooting
Ge n e ra l
Sp e cifica t io n s
Notice for customers in the
United Kingdom
A moulded plug complying with
BS 1363 is fitted to this equipment
for your safety and convenience.
The tape does not move w hen you
press an operation button.
WARNING
projecting parts)
On sa fe t y
Mass
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
•
Close the cassette compartment
securely.
Approx. 4.1 kg (9 lb. 1 oz) (incl.
batteries)
Supplied accessory
Mains lead (1)
To p re ve n t fire o r sh o ck
h a za rd , d o n o t e xp o se t h e
p la ye r t o ra in o r m o ist u re .
• As the laser beam used in the CD
player section is harmful to the
eyes, do not attempt to
disassemble the casing. Refer
servicing to qualified personnel
only.
• Should any solid object or liquid
fall into the player, unplug the
player, and have it checked by
qualified personnel before
operating it any further.
The pow er does not come on.
1
Press TAPE (direct power-on).
1
Press xZ to open the tape compartment and insert a
1
2
Play the music source you want.
•
•
Connect the mains lead securely.
Make sure the batteries are
inserted correctly.
The REC z button does not
function or the tape does not play
or record.
blank tape.
Remote control (1) (CFD-S32/ S32L only)
Should the fuse in the plug
supplied need to be replaced, same
rating fuse approved by ASTA or
CD Ra d io
Ca sse t t e -
Co rd e r
With the side you w ant to
record on facing upw ard
Display
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
Design and specifications are subject to
change without notice.
•
•
Replace all the batteries with new
ones if they are weak.
You cannot turn on the player
with the remote when you operate
the player on batteries (CFD-S32/
S32L only).
To a vo id e le ct rica l sh o ck, d o
n o t o p e n t h e ca b in e t . Re fe r
se rvicin g t o q u a lifie d
p e rso n n e l o n ly.
•
Make sure the safety tab on the
cassette is in place.
Press SLEEP to display “SLEEP.”
(This output is the value measured at a
distance of about 200 mm from the
objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/ min (rpm) to 500 r/ min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/ –2 dB
Wow and flutter
Below measurable limit
BSI to BS 1362, (i.e. marked with
•
Make sure "TAPE" appears in the
display.
Optional accessories
Sony MDR headphone series
or
mark) must be used.
•
If the player has not been used for
a long time, set it in the playback
mode to warm it up for a few
minutes before inserting a
cassette.
c
Poor or distorted playback,
recording or erasing quality.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
In fo rm a t io n
For customers in Europe
The pow er is not on, and
"bAttErY" and "Error" are
displayed alternately.
Operating Instructions
•
Clean the heads, pinch roller and
capstan with a cleaning swab
slightly moistened with cleaning
fluid or alcohol.
Cle a n in g t h e ca b in e t
• Clean the cabinet, panel and
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder, or
solvent, such as alcohol or
benzine.
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
•
Make sure the batteries are
inserted correctly.
2
Press xZ to open the tape compartment and insert a
recorded tape. Close the compartment.
•
•
Replace all the batteries with new
ones if they are weak.
TYPE II (high position) or TYPE
IV (metal) tape is being used. Use
TYPE I (normal) tape only.
3
Press SLEEP to select the minutes until the player goes
off automatically.
•
Replace all the batteries with new
ones if they are weak.
2
Select the program source you want to record.
With the side you w ant to
play facing upw ard
Radio section
Frequency range
Each time you press the button, the indication changes
as follows: “60” n “90” n “120” n no indication n
“10” n “20” n “30.”
There is no audio.
Ab o u t t h is m a n u a l
To record from the CD player
•
Make sure the function you want
to use appears in the display.
CFD-S22/S32
The instructions in this manual are
for the CFD-S22, CFD-S22L, CFD-
S32, CFD-S32L and CFD-922L.
Before you start reading, check
your model number. The CFD-S32L
is the model used for illustration
purposes.
Press CD and insert a CD (See "Playing a CD").
•
Demagnetize the heads using a
commercially available tape head
demagnetizer.
On p o w e r so u rce s
CFD-S22
CFD-S22L
CFD-S32
CFD-S32L
CFD-922L
This Compact Disc player is
classified as a CLASS 1 LASER
product.
FM
87.5 - 108 MHz
•
•
Adjust the volume.
Unplug the headphones when
listening through speakers.
• For AC operation, check that the
player's operating voltage is
identical with your local power
supply (see "Specifications") and
use the supplied mains lead; do
not use any other type.
The voltage selector is located at
the bottom of the player (for
Brazilian model only).
• The player is not disconnected
from the AC power source
(mains) as long as it is connected
to the wall outlet, even if the
player itself has been turned off.
• For battery operation, use six R20
(size D) batteries.
• When the batteries are not to be
used, remove them to avoid
damage that can be caused by
battery leakage or corrosion.
• The nameplate indicating
operating voltage, power
or 87.6 - 108 MHz
Display
Display
c
AM
531 - 1,602 kHz
Record/playback head
Capstan
The CLASS 1 LASER PRODUCT
label is located on the bottom
exterior.
CFD-S22L/S32L/922L
Noise is heard.
FM
87.5 - 108 MHz
531 - 1,602 kHz
153 - 279 kHz
•
Someone is using a portable
telephone or other equipment that
emits radio waves near the player.
tMove the portable telephone,
etc., away from the player.
MW
LW
Note
The name of the switch to turn on/
off this player is indicated as below:
“OPERATE”: CFD-S22L/ S32L/
922L
WARNING
Erase head
Pinch roller
Lens
IF
Do not install the appliance in a
confined space, such as a bookcase
or built-in cabinet.
3
Press N.
To record from the radio
FM: 10.7 MHz
Sony Corporation © 2000
To ca n ce l t h e sle e p fu n ct io n
AM/ MW/ LW: 450 kHz
Aerials
FM: Telescopic aerial
Press RADIO BAND• AUTO PRESET and tune in the
station you want (See "Listening to the radio").
CD Pla ye r
Press OPERATE (or POWER) to turn off the power.
“POWER”: CFD-S22/ S32
The CD does not play or “no dISC”
lights in the display even w hen a
CD is in place.
3-043-356-31(1)
AM/ MW/ LW: Built-in ferrite bar
aerial
Note
Display
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will
not go off until the tape reaches the end.
•
Make sure that the CD
compartment is closed.
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette
C-60
Frequency response
•
Place the CD with the label
surface up.
Ch o o sin g Po w e r So u rce s
To
Press
•
•
Clean the CD.
Take out the CD and leave the CD
compartment open for about an
hour to dry moisture
adjust the volume
VOLUME +, – (VOL +, – on the
remote, CFD-S32/ S32L only)
TYPE I (normal): 70 - 10,000 Hz
Re m o t e (CFD-S32/S32L o n ly)
The remote does not function.
Co n n e ct in g t h e m a in s le a d
Insert one end of the supplied mains lead to the AC IN socket located at the
rear of the player, and the other end to the mains.
Usin g t h e p la ye r o n b a t t e rie s
stop playback
xZ
condensation.
General
Speaker
Insert six R20 (size D) batteries (not supplied) into the battery compartment.
consumption, etc. is located at the
bottom.
•
Replace all the batteries in the
remote with new ones if they are
weak.
fast-forward or rewind the tape
pause playback
M or m
•
Make sure "Cd" appears in the
display.
3
Press z to start recording.
Full range: 10 cm dia., 3.2 ohms, cone
type (2)
Outputs
X
(N is depressed automatically.)
Notes
•
On p la ce m e n t
Press the button again to resume play
after pause.
The sound drops out.
Replace the batteries when the OPR/ BATT indicator dims or when the
player stops operating. Replace all the batteries with new ones. Before
you replace the batteries, be sure to take out the CD from the player.
•
Make sure that you are pointing
the remote at the remote sensor on
the player.
• Do not leave the player in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust or mechanical
shock.
• Do not place the player on an
inclined or unstable place.
• Do not place anything within 10
mm of the side of the cabinet. The
ventilation holes must be
unobstructed for the player to
operate properly and prolong the
life of its components.
• If the player is left in a car parked
in the sun, be sure to choose a
location in the car where the
player will not be subjected to the
direct rays of the sun.
• Since a strong magnet is used for
the speakers, keep personal credit
cards using magnetic coding or
spring-wound watches away from
the player to prevent possible
damage from the magnet.
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance
headphones
•
•
Reduce the volume.
Clean the CD, or replace it if the
CD is badly damaged.
eject the cassette
xZ
Maximum power output
•
To use the player on batteries, disconnect the mains lead from the player.
•
•
Remove any obstacles in the path
of the remote and the player.
Make sure the remote sensor is
not exposed to strong light such
as direct sunlight or fluorescent
lamp light.
turn on/ off the player
OPERATE (or POWER)
2.3 W + 2.3 W
•
•
•
Place the player in a location free
from vibration.
Clean the lens with a
Power requirements
For CD radio cassette-corder:
Brazilian model:
In se rt in g b a t t e rie s in t o t h e re m o t e
(CFD-S32/S32L o n ly)
No t e s o n ca sse t t e s
commercially available blower.
110 - 120V, 220 - 240V AC
selectable, 50/ 60 Hz
Other models:
•
Break off the cassette tab from side A or B to prevent accidental
recording. If you want to reuse the tape for recording, cover the broken
tab with adhesive tape.
The sound may drop out or noise
may be heard if the CD is
recorded using a personal
computer(CD-R,etc.).
1
to AC IN
To
Press
•
Move closer to the player when
using the remote.
230 V AC, 50 Hz
stop recording
xZ
9 V DC, 6 R20 (size D) batteries
For remote control (CFD-S32/ S32L only):
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 20 W
Battery life
Side A
pause recording
X
After trying the above remedies, if
you still have problems, unplug the
mains lead and remove all the
batteries. After all the indications in
the display disappear, plug the
power cord and insert the batteries
again. If the problem persists, please
consult your nearest Sony dealer.
Press the button again to resume recording.
2
to the mains
Ra d io
turn on/ off the player
OPERATE (or POWER)
The audio is w eak or has poor
quality.
For CD radio cassette-corder:
Tab for side A
Tab for side B
Insert tw o R6 (size AA) batteries (not supplied)
Tips
•
Replace all the batteries with new
ones if they are weak.
FM recording
•
Adjusting the volume or the audio emphasis will not affect the
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 20 h
Tape playback
•
The use of a cassette with more than 90 minutes of play time is not
recommended except for long, continuous recording or playback.
Re p la cin g b a t t e rie s
recording level.
•
Move the player away from the
TV.
Bra zilia n m o d e l o n ly: Ad ju st in g t h e vo lt a g e
With normal use, the batteries should last for about six months. When the
remote no longer operates the player, replace all the batteries with new
ones.
•
CFD-S22L/ S32L/ 922L only: If the MW/ LW program makes a
whistling sound after you've pressed z in step 3, press PLAY MODE•
MONO/ ST ISS (Interference Suppress Switch) repeatedly until the
noise is at a minimum.
For the best results, use the AC power as a power source for recording.
To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press TAPE.
Be sure to set the VOLTAGE SELECTOR (at the
bottom) to your local power supply.
The picture of your TV becomes
unstable.
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
CD playback
•
If you are listening to an FM
program near the TV with an
indoor antenna, move the player
away from the TV.
Note
•
•
When you operate the player on batteries, you cannot turn on the player
using the remote.
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Tip
Only for the customers supplied w ith an AC plug adaptor:
Use the supplied AC plug adaptor if the plug of the main lead does not
match your outlet.
3 Press z.
Download from Www.Somanuals.com. All Manuals Search And Download.
|