4-122-238-12(1)
DVD Home Theatre
System
Operating Instructions
DAV-HDX285 / HDX585 / HDX685
©2009 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
11) Only use attachments/accessories specified by the
manufacturer.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna (aerial).
– Increase the separation between the equipment and
receiver.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
®
ENERGY STAR is a U.S.
– Consult the dealer or an experienced radio/TV
technician for help.
registered mark.
®
As an ENERGY STAR partner,
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
Sony Corporation has determined
that this product meets the ENERGY
STAR guidelines for energy
®
efficiency.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
“DVD-RW,” “DVD-R,” “DVD+RW,”
“DVD+R,” “DVD VIDEO,” and the “CD”
logos are trademarks.
About These Operating
Instructions
“BRAVIA” is a trademark of Sony Corporation.
• The instructions in these Operating
Instructions describe the controls on the
remote. You can also use the controls on the
unit if they have the same or similar names as
those on the remote.
“PLAYSTATION” is a trademark of Sony
Computer Entertainment Inc.
®
DivX is a video file compression technology,
• The Control Menu items may vary depending
on the area.
developed by DivX, Inc. (Except for North
American models).
• “DVD” may be used as a general term for a
DVD VIDEO, DVD+RW/DVD+R, and DVD-
RW/DVD-R.
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license (Except for North American models).
• Measurements are expressed in feet (ft) for
North American models.
• The default setting is underlined.
“S-AIR” and its logo are trademarks of Sony
Corporation.
Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
About MPEG-4 Visual
(Except for North American models)
THIS PRODUCT IS LICENSED UNDER THE
MPEG-4 VISUAL PATENT PORTFOLIO
LICENSE FOR THE PERSONAL AND NON-
COMMERCIAL USE OF A CONSUMER FOR
DECODING VIDEO IN COMPLIANCE
WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”) THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE.
ADDITIONALINFORMATIONINCLUDING
THAT RELATING TO PROMOTIONAL,
INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED
FROM MPEG LA, LLC. SEE HTTP://
WWW.MPEGLA.COM
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
**Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2008
DTS, Inc. All Rights Reserved.
This system incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About the S-AIR function
The system is compatible with the S-AIR
function, which allows transmission of sound
between S-AIR products wirelessly.
The following S-AIR products can be used with
the system:
• Surround amplifier: You can enjoy surround
speaker sound wirelessly.
• S-AIR receiver: You can enjoy system sound
in another room.
These S-AIR products can be purchased as an
options (the S-AIR product lineup differs
depending on the area).
Notes or instructions for the surround amplifier
or S-AIR receiver in these Operating
Instructions refer only to when the surround
amplifier or S-AIR receiver is used.
For details on the S-AIR function, see “Using an
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Getting Optimal Surround Sound for a
Room.............................................. 80
Calibrating the Appropriate Settings
Automatically................................. 81
Controlling the TV with the Supplied
Remote ........................................... 82
Selecting the Effect to Suit
Step 3: Performing the Quick
Step 5: Enjoying Surround
the Source....................................... 84
Enjoying Multiplex Broadcast
Sound.............................................. 84
Changing the Input Level of the Sound
from Connected Components......... 85
Changing the Brightness of the Front
Panel Display.................................. 86
Adjusting the Delay Between the Picture
and Sound .......................................56
Changing the System Settings by Using
the Setup Display............................59
Control for HDMI/External
Using the Control for HDMI Function for
“BRAVIA” Sync ............................70
Using the DIGITAL MEDIA PORT
Adapter ...........................................73
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable Discs
Type
Disc logo
Characteristics
Icon
DVD VIDEO
• DVD VIDEO
• DVD-R/DVD-RW in DVD VIDEO
format or video mode
• DVD+R/DVD+RW in DVD VIDEO
format
VR (Video
Recording) mode
• DVD-R/DVD-RW in VR (Video
Recording) mode (except for DVD-R
DL)
VIDEO CD
• VIDEO CD (Ver. 1.1 and 2.0 discs)
• Super VCD
• CD-R/CD-RW/CD-ROM in video CD
format or Super VCD format
Super Audio CD
• Super Audio CD
CD
• Audio CD
• CD-R/CD-RW in audio CD format
DATA CD
–
–
• CD-R/CD-RW/CD-ROM in DATA CD
1)
format, containing MP3 files , JPEG
2)
3)
image files , DivX video files , and
3)
MPEG4 video files , and conforming to
4)
ISO 9660 Level 1/Level 2, or Joliet
(extended format)
DATA DVD
• DVD-ROM/DVD-R/DVD-RW/
DVD+R/DVD+RW in DATA DVD
1)
format, containing MP3 files , JPEG
2)
3)
image files , DivX video files , and
3)
MPEG4 video files , and conforming to
UDF (Universal Disk Format)
1)MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG for compresses audio data. MP3 files
must be in MPEG1 Audio Layer 3 format.
2)JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association
(JEITA).)
3)Except for North American models.
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4)A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for
Standardization).
Notes on discs
This product is designed to playback discs that conform to the Compact Disc (CD) standard.
DualDiscs and some of the music discs encoded with copyright protection technologies do not conform
to the Compact Disc (CD) standard, therefore, these discs may not be playable by this product.
Example of discs that the system cannot play
The system cannot play the following discs:
• CD-ROM/CD-R/CD-RW other than those recorded in the formats listed on page 7
• CD-ROM recorded in PHOTO CD format
• Data part of CD-Extra
• CD Graphics disc
• DVD Audio
• DATA CD/DATA DVD that does not contain MP3 files, JPEG image files, DivX video files*, or
MPEG4 video files*
• DVD-RAM
• Blu-ray Disc
* Except for North American models.
Also, the system cannot play the following discs:
• A DVD VIDEO with a different region code (page 9)
• A disc that has a non-standard shape (e.g., card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape or a sticker still left on it
Note about CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW cannot be played on this system
due to the recording quality or physical condition of the disc, or the characteristics of the recording
device and authoring software.
The disc will not play if it has not been correctly finalized. For more information, refer to the operating
instructions for the recording device.
Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have
been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs/DATA
DVDs created in Packet Write format cannot be played.
About Multi Session CD
• This system can play a Multi Session CD when an MP3 file is contained in the first session. Any
subsequent MP3 files recorded in later sessions can also be played back.
• This system can play a Multi Session CD when a JPEG image file is contained in the first session.
Any subsequent JPEG image files recorded in later sessions can also be played back.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• If MP3 files and JPEG image files in music CD format or video CD format are recorded in the first
session, only the first session will be played back.
Region code
Your system has a region code printed on the rear of the unit and will only play a DVD labeled with
the same region code.
ALL
A DVD VIDEO labeled
will also play on this system.
If you try to play any other DVD VIDEO, the message [Playback prohibited by area limitations.] will
appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be given even
though playing the DVD VIDEO is prohibited by area restrictions.
Note about playback operations of a DVD or VIDEO CD
Some playback operations on a DVD or VIDEO CD may be intentionally set by software producers.
Since this system will play a DVD or VIDEO CD according to the disc contents the software producers
designed, some playback features may not be available. Be sure to read the operating instructions
supplied with the DVD or VIDEO CD.
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Unpacking
DAV-HDX285
• Front speakers (2)
• FM wire antenna (aerial) (1) • Foot pads (1 set)
or
• Operating Instructions
• Quick Setup Guide
• Speaker cords (6, red/white/
green/gray/blue/purple)
For U.S. and Australian
• Center speaker (1)
models
• DIGITAL MEDIA PORT
adapter (TDM-iP20) (1)
• Video cord (1)
• Surround speakers (2)
• Remote commander
(remote) (1)
• Operating Instructions for
the DIGITAL MEDIA
• Subwoofer (1)
PORT adapter (TDM-iP20)
For U.S. models
• R6 (size AA) batteries (2)
• Setup Disc (DVD)
• Calibration mic (1)
• AM loop antenna (aerial) (1)
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DAV-HDX585
• Front speakers (2)
• FM wire antenna (aerial) (1) • Posts (2)
or
• Bases (2)
• Speaker cords (6, red/white/
green/gray/blue/purple)
• Screws (black) (4)
• Center speaker (1)
• Video cord (1)
• Screws (with washer) (4)
• Surround speakers (2)
• Remote commander
(remote) (1)
• Operating Instructions
• Quick Setup Guide
• Setup Disc (DVD)
• DIGITAL MEDIA PORT
adapter (TDM-iP20) (1)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• Subwoofer (1)
• Operating Instructions for
the DIGITAL MEDIA
PORT adapter (TDM-iP20)
• AM loop antenna (aerial) (1)
• Foot pads (1 set)
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DAV-HDX685
• Front speakers (2)
• AM loop antenna (aerial) (1) • Calibration mic (1)
• Foot pads (1 set)
• FM wire antenna (aerial) (1)
or
• Posts (4)
• Center speaker (1)
• Speaker cords (6, red/white/
green/gray/blue/purple)
• Bases (4)
• Surround speakers (2)
• Video cord (1)
• Screws (black) (8)
• Screws (with washer) (8)
• Remote commander
(remote) (1)
• Subwoofer (1)
• Operating Instructions
• R6 (size AA) batteries (2)
• Quick Setup Guide
• Setup Disc (DVD)
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment. To use the remote, point it at the remote sensor on the unit.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Installing the System
Positioning the system
For the best possible surround sound, place all speakers at the same distance from the listening position
(A). The distance can be between 1.0 to 7.0 meters.
If you cannot place the center speaker and surround speakers at the same distance as (A), you can move
the center speaker up to 1.6 meters closer to the listening position (B), and the surround speakers up
to 5.0 meters closer to the listening position (C).
The subwoofer can be placed anywhere in the room.
Center speaker
Subwoofer
Front left speaker (L)
Front right speaker (R)
B
A
A
A
A
A
C
C
Surround left speaker (L)
Surround right speaker (R)
Note
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,
oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not lean or hang on a speaker, as it may fall down.
GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the foot pads to the subwoofer
Attach the foot pads (supplied) to the bottom of the subwoofer to stabilize the subwoofer and prevent
it from slipping.
,
Remove the foot pads from
the protective cover.
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the speakers
(DAV-HDX585/DAV-HDX685 only)
Before connecting the speakers, attach the speaker stand to the speaker.
(For the front speakers of DAV-HDX585, and the front and surround speakers of DAV-HDX685)
Use the parts as follows:
DAV-HDX585
• Front speakers (2)
• Speaker cords (2, red/white)
• Posts (2)
• Bases (2)
• Screws (black) (4)
• Screws (with washer) (4)
DAV-HDX685
• Front and surround speakers (4)
• Speaker cords (4, red/white/blue/gray)
• Posts (4)
• Bases (4)
• Screws (black) (8)
• Screws (with washer) (8)
Note
• Spread a cloth on the floor to avoid damaging the floor when you assemble the speakers.
Tip
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Insert the post into the hole on the bottom of the speaker so that the screw on the post
faces the front of the speaker.
Speaker
,
Screw
Post
2
Adjust the height of the speaker, then secure the post with two screws (with washer).
You can change the height of the speaker depending on the screw positions. Adjust the screw holes
of the post to the holes on the rear of the speaker (A, B, C, or D). The height of the speaker can
be increased by using the holes in order from A to D.
Rear of the speaker
Example: Lowest position
A
B
C
D
Secure two screws (with
washer).
Post
GB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Thread the speaker cord through the hole in the base and post.
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected.
Use the speaker cords as follows:
• Front left speaker (L): White
• Front right speaker (R): Red
• Surround left speaker (L): Blue (DAV-HDX685 only)
• Surround right speaker (R): Gray (DAV-HDX685 only)
Be careful with the orientation of the post. Thread the speaker cord into the end of the post that has
two holes.
Post
Top of the base
Bottom of the base
,
Speaker cord
Base
Rear of the speaker
GB
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Connect the speaker cords to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord
with the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Surround left speaker (L): Blue (DAV-HDX685 only)
Surround right speaker (R): Gray (DAV-HDX685 only)
Rear of the speaker
5
Attach the post to the base.
Insert the post so that the slot on the lower part of the post aligns with the projection of the base,
then secure the post with the two screws (black).
Post
Slot
,
Projection
Base
Screws
(black)
Note
• Make sure that the slot on the post aligns with the projection of the base by rotating the post slightly.
GB
19
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Take up any speaker cord slack.
Take up slack in the speaker cord by pulling from the bottom of the base.
Secure the speaker cord by running it
through the slot.
Adjust the length of the cord.
Fully-assembled illustration
DAV-HDX585
Front right speaker (R):
Red label
Front left speaker (L):
White label
Red
White
GB
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DAV-HDX685
Front right speaker (R):
Red label
Surround right speaker (R):
Gray label
Front left speaker (L):
White label
Surround left speaker (L):
Blue label
White
Red
Blue
Gray
GB
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the speakers on a wall
Caution
• Contact a screw shop or installer for information regarding the wall material or screws to be used.
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a beam. Install the speakers on a vertical and flat wall where reinforcement is applied.
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or
improper screw installation, natural calamity, etc.
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Center speaker: Green
Surround left speaker (L): Blue
Surround right speaker (R): Gray
1
2
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
Hole on the back of
4 mm (5/32 inch)
the speaker
5 mm
(7/32 inch)
30 mm (1 3
/16 inches)
10 mm
13
(
/32 inch)
Fasten the screws to the wall.
DAV-HDX285
For the other speakers
For the center speaker
145 mm
(5 3
4 inches)
/
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
GB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DAV-HDX585
For the front speakers
For the center speaker
145 mm
(5 3
4 inches)
/
101.6 mm
4 inches
(
)
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch)
(
/
to
/
inch)
32
32
32
32
For the surround speakers
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
DAV-HDX685
For the other speakers
For the center speaker
145 mm
(5 3
4 inches)
/
101.6 mm
4 inches
(
)
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch)
(
/
to
/
inch)
32
32
32
32
GB
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Hang the speakers on the screws.
Hole on the back of
the speaker
5 mm
(7/32 inch)
10 mm
13
(
/32 inch)
Rear of the speaker
GB
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other
connections are made.
Note
• When you connect another component with a volume control, turn down the volume of the other components to a
level where sound is not distorted.
Connecting the speakers
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker.
Connect the speaker cords to match the color of the SPEAKER jacks of the unit.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #. Do not catch the speaker cord
insulation (rubber covering) in the speaker terminals.
To connect speaker cords to the unit
When connecting to the unit, insert the connector until it clicks.
A
N
N
E
T
N
A
Red
(Front right speaker (R)) (Front left speaker (L))
White
A
FM
COAXIAL 75
0
0
1
-T
W
Z
E
TV/VIDEO
AUDIO IN
Purple
(Subwoofer)
VIDEO
OUT
T
U
O
O
E
ID
V
T
N
E
N
O
P
M
O
L
C
R
R
E
K
A
E
P
/CR
S
PR
/CB
PB
Y
SUR
L
SUR
T
R
FRONT
D
H
L
R
Blue
(Surround left speaker (L))
O
P
M
I
O
M
FRONT
R
D
.
0
V
T
DIGITAL IN
R
E
COAXIAL
K
A
E
P
S
OPTICAL
Gray
(Surround right speaker (R))
O
W
B
U
S
CENTER
Green
(Center speaker)
To connect speaker cords to the speaker
Rear of the speaker
Connector
(–)
(+)
Color tube
GB
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Video connection)
This connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
C Component video cable
A
N
N
E
T
N
A
(not supplied)
AM
FM
COAXIAL 75
0
0
1
-T
W
Z
E
TV/VIDEO
AUDIO IN
VIDEO
OUT
T
U
O
O
E
ID
V
T
N
E
N
O
P
M
O
L
C
R
R
E
K
A
E
P
/CR
S
PR
/CB
A Video cord (supplied)
PB
Y
SUR
L
SUR
R
FRONT
D
H
L
T
RT
U
O
P
M
I
O
M
D
FRONT
R
V
5
C
D
X
A
M
A
.7
0
V
T
DIGITAL IN
R
E
COAXIAL
K
A
E
P
S
OPTICAL
R
E
F
O
O
W
B
U
S
CENTER
B HDMI cable (not supplied)
To the HDMI IN jack
of the TV.
To the component
video input jacks of
the TV.
To the video input jack of
the TV.
Method 1: Video cord (A) connection
This is the basic connection.
Method 2: HDMI* cable (B) and video cord (A) connection
If your TV has an HDMI jack, connect to the TV both with an HDMI cable and video cord. Picture
quality will be improved compared to using only the video cord connection.
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the
video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the HDMI OUT
jack.
* HDMI (High-Definition Multimedia Interface)
Method 3: Component video cable (C) and video cord (A) connection
If your TV does not have an HDMI jack, but has component video input jacks, connect to the TV both
with a component video cable and video cord. Picture quality will be improved compared to using only
the video cord connection.
When connecting with the component video cable, you need to set the type of output signal to
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the
video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the
COMPONENT VIDEO OUT jack.
GB
26
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the color system (PAL or NTSC) (Asian, Australian, and
Middle Eastern models only)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color
system.
The initial setting of the system for Australian and Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
1
2
Turn off the system by pressing "/1.
Turn on the system by pressing "/1 on the unit while pressing . on the unit.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front panel display when the color system is set to NTSC.
GB
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Audio connection)
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system,
perform this connection.
A
N
N
E
T
N
A
AM
FM
COAXIAL 75
0
0
1
-T
W
Z
E
TV/VIDEO
AUDN
VIDEO
OUT
T
U
O
O
E
ID
V
T
N
E
N
O
P
M
O
L
C
R
D Audio cord (not
supplied)
R
E
K
A
E
P
S
/CR
PR
/CB
PB
Y
SUR
L
SUR
R
FRONT
D
H
L
T
RT
U
O
P
M
I
O
M
D
FRONT
R
V
5
C
D
X
A
M
A
.7
0
V
T
DIGITAL IN
R
E
COAXIAL
K
A
E
P
S
OPTICA
R
E
F
O
O
W
B
F Digital coaxial cord (not
U
S
CENTER
supplied)
E Digital optical cord
(not supplied)
To the audio out jacks of
the TV.
To the digital optical out
jack of the TV.
To the digital coaxial out jack of
the TV.
Method 1: Audio cord (D) connection
This is the basic connection and sends an analog audio signal.
Method 2: Digital optical cord (E) or digital coaxial cord (F) connection
When the TV has a digital optical or coaxial output jack, you can improve sound quality by connecting
with a digital optical or coaxial cord in addition to an audio cord connection.
Note
• The system can accept both digital and analog signals. Digital signals have priority over analog signals. (COAXIAL
has priority over OPTICAL.) If the digital signal ceases, the analog signal will be processed after 2 seconds.
Tip
• You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV/VIDEO
(AUDIO IN R/L) jacks or DIGITAL IN OPTICAL/COAXIAL jacks instead of the TV.
GB
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the other components
You can enjoy connected components via the system’s speakers.
Portable audio source (not supplied): G
DIGITAL MEDIA PORT adapter: H (TDM-iP20 is supplied with U.S. and Australian models. You
can also use other DIGITAL MEDIA PORT adapters.)
G Stereo mini-plug cord
(not supplied)
To a portable audio source
A
N
N
E
T
N
A
EZW-T100 slot (See “Wireless
A
FM
COAXIAL 75
0
0
1
-T
W
Z
E
TV/VIDEO
AUDIO IN
VIDEO
OUT
T
U
O
O
E
ID
V
T
N
E
N
O
P
M
O
L
C
R
R
E
K
A
E
P
/CR
S
PR
/CB
PB
Y
SUR
L
SUR
R
FRONT
D
H
L
T
RT
U
O
P
M
I
O
M
D
FRONT
R
H DIGITAL MEDIA PORT
V
5
C
D
X
A
M
A
.7
0
V
T
DIGITAL IN
adapter (page 73)
R
E
COAXIAL
K
A
E
P
S
OPTICAL
Note
R
E
F
O
O
W
B
U
S
CENTER
• Connect the DIGITAL MEDIA PORT
adapter so that the V marks are aligned.
When disconnecting, pull out while
pressing
.
Tip
• You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV/VIDEO
(AUDIO IN R/L) jacks or DIGITAL IN OPTICAL/COAXIAL jacks instead of the TV.
Wireless system options
By using an S-AIR product (not supplied), you can enjoy wireless performance by transmission from
the system. For details, see “Using an S-AIR Product” (page 74) or refer to the operating instructions
of the S-AIR product.
GB
29
Download from Www.Somanuals.com. All Manuals Search And Download.
If your TV has multiple audio/video inputs
You can enjoy sound with the speakers of the system through the connected TV. Connect the
components as follows.
VCR, digital satellite receiver,
TV
PlayStation, etc.
VCR, digital satellite receiver,
PlayStation, etc.
System
:Signal flow
Select the component on the TV. For details, refer to the operating instructions of the TV.
If the TV does not have multiple audio/video inputs, a switcher will be necessary to receive sound from
more than one component.
GB
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the antenna (aerial)
To assemble the AM loop antenna (aerial)
To connect the antenna (aerial)
AM loop antenna (aerial)
(supplied)
A
N
N
E
T
N
A
AM
A
FM
COAXIAL 75
or
FM wire antenna (aerial)
(supplied)
Note
• Keep the AM loop antenna (aerial) and cord away from the system or other AV components, as noise may result.
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Outdoor FM antenna (aerial)
Unit
ANTENNA
FM
COAXIAL 75
AM
GB
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of the unit to a wall outlet (mains), connect all the
speakers to the unit.
Wall outlet (mains): The shape of the wall outlet (mains)
differs depending on the area.
About the demonstration
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display.
Setting the demonstration mode to on/off
1
Press [/1 on the unit.
The system turns on.
2
3
Press SYSTEM MENU.
Press X/x repeatedly until “DEMO” appears in the front panel display, then press
c.
or
4
Press X/x to select a setting.
• “DEMO ON”: On.
• “DEMO OFF”: Off.
5
6
Tip
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
• When you purchase the system new, or if the system is at its factory default settings (ex., after performing “COLD
RESET” (page 89)), you can turn off the demonstration simply by pressing [/1 on the remote (except for U.S.
models).
GB
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Press X/x to select a language, then
press
.
Step 3: Performing the
Quick Setup
Follow the Steps below to make the basic
adjustments for using the system.
The Setup Display for selecting the aspect
ratio of the TV to be connected appears.
VIDEO SETUP
TV TYPE:
16:9
16:9
PROGRESSIVE (COMPON
4:3 OUTPUT:
BLACK LEVEL:
BLACK LEVEL (COMPONENT OUT):
PAUSE MODE:
4:3 LETTER BOX
4:3 PAN SCAN
Displayed items vary depending on the area.
OFF
AUTO
"/1
Press X/x to select the setting that
matches your TV type, then press
.
• [16:9]: For a wide-screen TV or a 4:3
standard TV with a wide-screen mode
C/X/x/c,
• [4:3 LETTER BOX] or [4:3 PAN SCAN]:
For a 4:3 standard TV (page 60)
DISPLAY
The Setup Display for the Control for
HDMI function appears.
1
2
Turn on the TV.
HDMI SETUP
HDMI RESOLUTION:
CONTROL FOR HDMI:
VOLUME LIMIT:
AUTO(1920x1080p)
ON
ON
OFF
OFF
SD
Press [/1.
YCB
C
R/RGB(HDMI):
Note
AUDIO(HDMI):
• Make sure that the function is set to “DVD”
JPEG RESOLUTION:
3
4
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
7
Press X/x to select the setting, then
press
.
[Press [ENTER] to run QUICK SETUP.]
appears at the bottom of the TV screen. If
this message does not appear, recall the
• [ON]: The Control for HDMI function
(page 70) is set to on.
• [OFF]: The Control for HDMI function is
set to off.
Press
without inserting a disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
The Setup Display for selecting the speaker
formation appears.
SPEAKER FORMATION
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
MENU:
AUDIO:
SUBTITLE:
FRENCH
SPANISH
PORTUGUESE
STANDARD
GB
33
Download from Www.Somanuals.com. All Manuals Search And Download.
location, such as another room, proper
measurement will not be obtained.
8
9
Press C/c to select the speaker
formation image as the speakers are
actually positioned, then press
• The environment of the room in which the
system is installed may affect measurements.
When the measurements differ considerably
from the status of the speaker installation,
perform the speaker settings manually by
.
For details, see “Getting Optimal Surround
Connect the calibration mic (supplied)
to the A.CAL MIC jack on the front
panel.
11
Unplug the calibration mic, press C/c
Set up the calibration mic at ear level using
a tripod, etc. (not supplied).
to select [YES], then press
.
Quick Setup is finished. All connections
and setup operations are complete.
The front of each speaker should face the
calibration mic, and there should be no
obstruction between the speakers and the
calibration mic.
To quit the Quick Setup
Press DISPLAY in any Step.
To recall the Quick Setup display
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
3
4
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
Calibration mic
94( 99)
1( 1)
0: 01: 08
DVD VIDEO
T
CUSTOM
CUSTOM
QUICK
Press X/x to select [QUICK], then press
.
10
Press C/c to select [YES], then press
.
The Quick Setup display appears.
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
Note
• Loud test sounds are output when [AUTO
CALIBRATION] starts. You cannot turn the
volume down. Give consideration to children
and neighbors.
• Before [AUTO CALIBRATION], install the
surround amplifier in the appropriate location. If
you install the surround amplifier in an improper
GB
34
Download from Www.Somanuals.com. All Manuals Search And Download.
**Depending on the area, [720 × 480/576p] may
appear.
Setting the type of video
output to match your TV
Does your TV accept progressive
signals?
Depending on the connection of the TV
(page 26), select the type of video output of the
system.
Progressive is a method for displaying TV
images which reduces flickering and sharpens
the image. To use this method, you need to
connect to a TV that accepts progressive signals.
To select the type of video signal
output from the HDMI OUT jack
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
When you connect the unit and the TV with an
HDMI cable, select the type of video signals
output from the HDMI OUT jack.
2
Press
in stop mode.
DISPLAY while the system is
For details, refer also to the operating
The Control Menu display appears on the
TV screen.
instructions supplied with the TV/projector, etc.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
3
4
5
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
2
Press
in stop mode.
DISPLAY while the system is
Press X/x to select [CUSTOM], then
press
.
The Control Menu display appears on the
TV screen.
The Setup Display appears.
3
4
5
Press X/x to select
then press
[SETUP],
Press X/x to select [VIDEO SETUP],
.
then press
.
The options for [SETUP] appear.
The options for [VIDEO SETUP] appear.
Press X/x to select [CUSTOM], then
6
7
Press X/x to select [PROGRESSIVE
press
.
(COMPONENT OUT)], then press
Press X/x to select the desired setting,
then press
.
The Setup Display appears.
.
Press X/x to select [HDMI SETUP], then
press
.
[OFF]: The system does not output
progressive signals. Select this setting
when:
The options for [HDMI SETUP] appear.
6
7
Press X/x to select [HDMI
– your TV does not accept progressive
signals, or,
RESOLUTION], then press
Press X/x to select the desired setting,
then press
.
– your TV is connected via jacks other than
the COMPONENT VIDEO OUT jacks.
[ON]: The system outputs progressive
signals. Select this setting when:
.
• [AUTO (1920 × 1080p)]: The system
outputs the optimal video signal for the
connected TV.
– your TV accepts progressive signals,
and,
• [1920 × 1080i]: The system outputs 1920
× 1080i* video signals.
– the TV is connected via the
• [1280 × 720p]: The system outputs 1280 ×
720p* video signals.
COMPONENT VIDEO OUT jacks.
When you select [ON], the confirmation
display appears. Follow the Steps below.
• [720 × 480p]**: The system outputs 720 ×
480p* video signals.
* i: interlace, p: progressive
GB
35
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
Press C/c to select [START], then
press
.
Step 4: Selecting the
Source
The system outputs a progressive signal for
5 seconds. Check that the screen is
displayed correctly.
You can select the playback source.
Press C/c to select [YES], then press
.
The system outputs a progressive signal.
When you select [NO], the system does not
output a progressive signal.
FUNCTION
+/–
Press FUNCTION +/– repeatedly until the
desired function appears in the front panel
display.
Each time you press FUNCTION +/–, the
function changes as follows.
“DVD” y “TUNER FM” y “TUNER AM”
y “TV/VIDEO” y “DMPORT” y
“AUDIO” y …
Function
Source
“DVD”
Disc that is played by the
system
“TUNER FM”/
“TUNER AM”
FM/AM radio (page 67)
“TV/VIDEO”
TV or component that is
connected to the TV/
VIDEO jacks on the rear
panel
“DMPORT”
“AUDIO”
DIGITAL MEDIA PORT
adapter (page 73)
Portable audio source that
is connected to the AUDIO
IN jack on the front panel
GB
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Enjoying Surround Sound
You can enjoy surround sound simply by selecting one of the system’s pre-programmed decoding
modes. They bring the exciting and powerful sound of movie theaters into your home.
SYSTEM MENU
X/x/c,
Enjoying TV sound with the 5.1 channel surround sound effect
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c.
3
4
Press X/x repeatedly until “PRO LOGIC” appears in the front panel display.
Press
.
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Note
• When TV program sound is monaural, sound is output only from the center speaker.
Selecting surround sound effects based on your listening preference
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c.
3
Press X/x repeatedly until the surround sound effect you want appears in the front panel
display.
See the table below for surround sound effect descriptions.
GB
37
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
About speaker output
The table below describes the options when you connect all the speakers to the unit and you set
For Australian models, the default setting is “A.F.D. STD.” For other models, the default setting is
“A.F.D. MULTI” (when connecting the headphones to the unit, the default setting is “HP 2CH”).
Sound from
Surround effect
Effect
Depending on the source.
“A.F.D. STD”
The system discriminates the sound format of the source and
presents sound as it was recorded/encoded.
(AUTO FORMAT
DIRECT STANDARD)
“A.F.D. MULTI”
• 2 channel source: The system outputs 2 channel sound from
the front and surround speakers by assigning the 2 channel
sound to the surround left and right channels.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source.
(AUTO FORMAT
DIRECT MULTI)
“PRO LOGIC”
“PLII MOVIE”
“PLII MUSIC”
• 2 channel source: The system simulates surround sound
from 2 channel sources and outputs sound from all the
speakers.
– “PRO LOGIC” performs Dolby Pro Logic decoding.
– “PLII MOVIE” performs Dolby Pro Logic II movie
mode decoding.
– “PLII MUSIC” performs Dolby Pro Logic II music mode
decoding.
• Multi-channel source: The system outputs sound from the
speakers depending on the number of channels of the
source.
“2CH STEREO”
The system outputs the sound from the front speakers and
subwoofer regardless of sound format or number of channels.
Multi-channel surround formats are downmixed to 2
channels.
“HP 2CH”
(HEADPHONE 2
CHANNEL STEREO)
The system outputs the sound from the headphones
regardless of sound format or number of channels. Multi-
channel surround formats are downmixed to 2 channels.
GB
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound from
Surround effect
Effect
“HP VIRTUAL”
(HEADPHONE
VIRTUAL)
The system outputs the sound from the headphones by
adding a surround effect regardless of sound format or
number of channels.
To turn the surround effect off
Select “A.F.D. STD,” “2CH STEREO,” or “HP 2CH” for “DEC. MODE.”
Note
• When the bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• You cannot select the decoding mode while the system is loading a disc.
• Depending on the input stream, the decoding mode may not be effective.
• When you select “A.F.D. MULTI,” the surround or stereo effect may not be effective. In this case, select “A.F.D.
STD,” “PRO LOGIC,” “PLII MOVIE,” or “PLII MUSIC.”
• When changing the decoding mode while using the S-AIR receiver, sound from the S-AIR receiver may skip.
GB
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Press DISC 1-5.
Press the button of the disc number you
want.
Disc
When no disc is in the disc stocker you
select, “NO DISC” appears in the front
panel display. Perform next Step while
“*DISC-1* (e.g., 2-5)” flashes.
Playing a Disc
Press Z on the unit to open the disc
tray, and place a disc on the tray.
Place one disc on the tray, and then press Z.
Depending on the DVD VIDEO or VIDEO CD,
some operations may be different or restricted.
Refer to the operating instructions supplied with
your disc.
Adjust the volume
"/1
DISC 1-5/indicators
With the label side up.
Disc tray
N FUNCTION
Z
Connect
Note
headphones
• When you play an 8 cm disc, place it on the
inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
• Do not place more than one disc on the tray.
"/1
FUNCTION
+/–
6
Press H.
DISC SKIP
The system starts playback (continuous
play) of the disc whose DISC indicator is
green.
x To load other discs
Press DISC 1-5 (any empty slot) and Z to
load the disc.
MUTING
VOLUME +/–
STEP
x To play back other discs
Press DISC SKIP on the remote or DISC 1-
5 on the unit.
/
/
,
./>
H
/m/
M/
x
7
Adjust the volume by using VOLUME +/
– on the remote or the VOLUME control
on the unit.
X
1
2
Turn on your TV.
The volume level appears on the TV screen
and in the front panel display.
Switch the input selector on the TV to
this system.
Note
3
Press "/1.
• When you set the Control for HDMI function to on,
the TV that is connected to the system with an HDMI
cable can be sync-operated with the system. For
details, see “Using the Control for HDMI Function
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION +/– to select “DVD.”
GB
40
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
Tip
• The DISC 1-5 indicators change their color as
follows:
Change a disc while
playing another disc
DISC SKIP
– Green: the disc is selected, or the disc is being
played back.
Play the desired disc
directly
DISC 1-5 on the unit.
– Off: there is no disc.
Stop play and remove
the disc
DISC 1-5 and Z on the
unit.
– Orange: a disc is loaded in the disc stocker but not
selected.
Locate a point quickly M/
by playing a disc in fast playing a disc. Each time
or
/m while
– The indicator turns off if an unplayable disc is
inserted.
forward or fast reverse you press M/
or
/
1)
(Scan)
m during scan, the
playback speed changes.
To turn the system off
Press "/1 while the system is on. The system
enters standby mode.
To return to normal speed,
press H. Actual speeds
may differ with some discs.
3)
To save power in standby mode
Press "/1 while the system is on.
Watch frame by frame M/
or
/m
2)
(Slow-motion Play)
while the system is in pause
To enter power saving mode, make sure that the
system is in the following status.
mode. Each time you press
3)
M/
or
/m
during Slow-motion Play,
the playback speed
changes. Two speeds are
available. To return to
normal playback speed,
press H.
– [CONTROL FOR HDMI] is set to [OFF]
– “S-AIR STBY” is set to “STBY OFF”
Play one frame at a time STEP
to go to the next
2)4)5)
To use the headphones
(Freeze Frame)
frame while the system is in
pause mode. Press STEP
to go to the preceding
Connect the headphones to the PHONES jack on
the unit. The sound of the system is muted.
You can also connect the headphones to the
PHONES jack on the surround amplifier. (The
sound of the system is muted.)
frame while the system is in
pause mode (DVD VIDEO/
DVD-R/DVD-RW only).
To return to normal
playback, press H.
Other operations
Replay the previous
scene (10 seconds
before)
(instant replay) during
playback.
6)
To
Press
x
Briefly fast forward the
current scene (30
(instant advance)
during playback.
Stop
Pause
X
7)
seconds ahead)
Resume play after pause X or H
1)Except for JPEG image files.
2)DVD VIDEO/DVD-R/DVD-RW/VIDEO CD only.
3)Except for VIDEO CDs.
Go to the next chapter,
track, or scene
>
1)
Go back to the
. twice in a second.
When you press . once,
you can go to the beginning
of the current chapter,
track, or scene.
preceding chapter,
4)You cannot search for a still picture on a DVD-VR.
1)
track, or scene
5)For a DATA CD/DATA DVD, this function works
only for video files (except for North American
models).
6)DVD VIDEO/DVD-RW/DVD-R only.
The button can be used except for DivX/MPEG4
video files (except for North American models).
Turn off the sound
temporarily
MUTING.
To cancel, press it again or
press VOLUME + to adjust
the sound volume.
GB
41
Download from Www.Somanuals.com. All Manuals Search And Download.
7)DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
DVD+R only.
The button can be used except for DivX/MPEG4
video files (except for North American models).
To display the subtitles
*
*
* Except for North American models.
If subtitles are recorded on a disc, you can turn
the subtitles on/off during playback. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language during
playback, or turn the subtitles on/off whenever
you want.
Note
• Noise may come from the disc changer when
changing discs or turning the system on/off.
However, this is just noise produced by the operation
of the internal mechanisms and does not indicate a
malfunction.
Press SUBTITLE during playback to select
the desired subtitle language.
To turn on/off the DISC 1-5
indicators’ illumination
When you do not operate the system for more
than 30 minutes, the illumination of the DISC 1-
5 indicators starts automatically. You can turn
the illumination on/off.
Note
• You can select the subtitles if the DivX video file has
an “.avi” or “.divx” extension and contains subtitle
information within the same file (except for North
American models).
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “ILLUM
MODE” appears in the front panel
Changing the sound
display, then press
or c.
3
Press X/x to select a setting.
• “ILLUM ON”: On.
• “ILLUM OFF”: Off.
When the system is playing a DVD VIDEO or
DATA CD/DATA DVD (DivX video files*)
recorded in multiple audio formats (PCM,
Dolby Digital, MPEG audio, or DTS), you can
change the audio format. If the DVD VIDEO is
recorded with multilingual tracks, you can also
change the language.
4
5
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
With a VIDEO CD, CD, DATA CD, or DATA
DVD, you can select the sound from the right or
left channel and listen to the sound of the
selected channel through both the right and left
speakers.
Displaying multi-angles and
subtitles
To change the angles
You cannot change the sound for a Super Audio
CD.
* Except for North American models.
If various angles (multi-angles) for a scene are
recorded on a DVD VIDEO, you can change the
viewing angle.
Press AUDIO repeatedly during playback to
select the desired audio signal.
x DVD VIDEO
Depending on the DVD VIDEO, the choice of
language varies.
Press ANGLE during playback to select the
desired angle.
When 4 digits are displayed, they indicate a
language code. See “Language Code List”
(page 106) to confirm which language the code
represents. When the same language is
GB
42
Download from Www.Somanuals.com. All Manuals Search And Download.
displayed two or more times, the DVD VIDEO
is recorded in multiple audio formats.
Checking the audio signal
format
x DVD-VR
The types of sound tracks recorded on a disc are
displayed.
*
*
Example:
* Except for North American models.
• [1: MAIN] (main sound)
• [1: SUB] (sub sound)
• [1: MAIN+SUB] (main and sub sound)
• [2: MAIN]
If you press AUDIO repeatedly during
playback, the format of the current audio signal
(PCM, Dolby Digital, DTS, etc.) appears as
shown below.
• [2: SUB]
x DVD
• [2: MAIN+SUB]
x VIDEO CD/CD/DATA CD (MP3 file)/DATA
DVD (MP3 file)
• [STEREO]: The standard stereo sound.
• [1/L]: The sound of the left channel
(monaural).
Example:
Dolby Digital 5.1 channel
LFE (Low
Frequency Effect)
Surround (L/R)
• [2/R]: The sound of the right channel
(monaural).
1: ENGLISH
DOLBY DIGITAL 3 / 2 .1
L
C
R
x DATA CD (DivX video file) /DATA DVD
(DivX video file) (Except for North American
models)
Front (L/R) +
Center
LFE
LS
RS
The choice of DATA CD or DATA DVD audio
signal formats differs, depending on the DivX
video file contained on the disc. The format
appears on the TV screen.
Currently playing program format
Example:
x Super VCD
Dolby Digital 3 channel
• [1:STEREO]: The stereo sound of audio track
1.
Surround
(Monaural)
Front (L/R)
• [1:1/L]: The sound of the left channel of audio
track 1 (monaural).
• [1:2/R]: The sound of the right channel of
audio track 1 (monaural).
1:SPANISH
DOLBY DIGITAL 2 / 1
L
R
• [2:STEREO]: The stereo sound of audio track
2.
S
• [2:1/L]: The sound of the left channel of audio
track 2 (monaural).
Currently playing program format
• [2:2/R]: The sound of the right channel of
audio track 2 (monaural).
x DATA CD (video file)/DATA DVD (video
file) (Except for North American models)
Example:
MP3 audio
1:MP3
128k
Bit rate
GB
43
Download from Www.Somanuals.com. All Manuals Search And Download.
x When the current layer is the Super
Audio CD layer
[CD] appears.
Selecting a playback area for a
Super Audio CD
3
Press
to change the layer.
• [SUPER AUDIO CD]: You can play the
Super Audio CD layer.
Some Super Audio CDs consist of a 2 channel
playback area and a multi-channel playback
area. You can select the playback area you want
to listen to.
When the system is playing a Super Audio
CD layer, “SA-CD” lights up in the front
panel display.
• [CD]: You can play the CD layer.
When the system is playing a CD layer,
“CD” lights up in the front panel display.
1
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
Note
• Each play mode function works only within the
selected layer or playback area.
2
3
Press X/x to select
[MULTI/
• When you select a CD layer, you cannot change
playback areas.
2CH], then press
.
The options for [MULTI/2CH] appear.
• Super Audio CD audio signals are not output from the
HDMI OUT jack.
Press X/x to select the desired setting
and press
.
• [MULTI]: You can play the multi-channel
playback area.
Playing a VIDEO CD with PBC
functions (Ver. 2.0)
(PBC Playback)
• [2CH]: You can play the 2 channel
playback area.
Note
• When the Super Audio CD does not have a multi-
channel playback area, you cannot select the
playback area.
With PBC (Playback Control) functions, you
can enjoy simple interactive operations, search
functions, and other such operations.
PBC playback allows you to play a VIDEO CD
interactively by following the menu on the TV
screen.
Changing a playback layer for
a hybrid Super Audio CD
1
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
Some Super Audio CDs consist of a Super
Audio CD layer and a CD layer. You can change
the playback layer you want to listen to.
2
Select the item number you want using
the number buttons.
If you make a mistake, press CLEAR to
cancel the number.
1
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
3
4
Press
.
Follow the instructions in the menu for
interactive operations.
2
Press X/x to select
[SUPER
AUDIO CD/CD LAYER], then press
.
Refer to the operating instructions supplied
with the disc, as the operating procedure
may differ depending on the VIDEO CD.
x When the current layer is the CD
layer
[SUPER AUDIO CD] appears.
GB
44
Download from Www.Somanuals.com. All Manuals Search And Download.
– you change the function by pressing FUNCTION
+/–.
To go back to the menu
Press O RETURN.
– you disconnect the AC power cord (mains lead).
• For a DVD-VR, VIDEO CD, Super Audio CD, CD,
DATA CD, or DATA DVD, the system remembers
the resume playback point for the current disc.
• The resume point is cleared when you select another
disc.
Note
• Depending on the VIDEO CD, [Press ENTER] in
Step 3 may appear as [Press SELECT] in the
operating instructions supplied with the disc. In this
case, press H.
• Resume Play does not work during Program Play and
Shuffle Play.
Tip
• To play without using the PBC function, press ./
• This function may not work properly with some
discs.
> or the number buttons while the system is in stop
mode to select a track, then press H or
. The
system starts playback. You cannot play still pictures
such as a menu. To return to PBC playback, press x
twice, then press H.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
To enjoy a disc that you played
before with resume playback
Resuming playback from the
point where you stopped the
disc
(Multi-disc Resume)
This system recalls the point where you stopped
the disc the last time it was played and resumes
playback from that point the next time you insert
the same disc. When the resume playback
memory is full, the resume playback point for
the earliest disc is deleted.
To activate this function, set [MULTI-DISC
RESUME] in [SYSTEM SETUP] to [ON]. For
details, see “[MULTI-DISC RESUME] (DVD
(Resume Play)
When you stop the disc, the system remembers
the point where you pressed x and “RESUME”
appears in the front panel display. As long as
you do not remove the disc, Resume Play will
work even if the system is set to standby mode
by pressing "/1.
1
While playing a disc, press x to stop
playback.
Note
• This system stores the resume points in memory for
up to 10 discs.
“RESUME” appears in the front panel
display.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
2
Press H.
The system starts playback from the point
where you stopped the disc in Step 1.
Note
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
point.
• The point where you stopped playing may be cleared
when:
– you eject the disc.
– the system enters standby mode (DATA CD/
DATA DVD only).
– you change or reset the settings on the Setup
Display.
– you change the parental control level.
GB
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Select the track you want to program.
For example, select track [02].
Using Play Mode
Press X/x to select [02] under [T], then
press
.
Creating your own program
Selected track
(Program Play)
PROGRAM
0: 03:51
T
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
02
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
You can play the contents of a disc in the order
you want by arranging the order of the tracks on
the disc to create your own program. You can
program up to 99 tracks.
Note
Total time of the programmed tracks
• You can program tracks on the current disc only.
1
2
3
Press
DISPLAY.
6
7
To program other tracks, repeat Steps
4 to 5.
The Control Menu display appears on the
TV screen.
The programmed tracks are displayed in the
selected order.
Press X/x to select
then press
[PROGRAM],
.
Press H to start Program Play.
The options for [PROGRAM] appear.
Program Play starts.
Press X/x to select [SET t], then
When the program ends, you can restart the
same program again by pressing H.
press
.
Total time of the programmed tracks
To return to normal play
PROGRAM
0: 00:00
T
Press CLEAR while the display for the program
setting is not displayed on the TV screen, or
select [OFF] in Step 3. To play the same
program again, select [ON] in Step 3 and press
.
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
To turn off the Control Menu
display
Tracks recorded on a disc
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
4
Press c.
The cursor moves to the track row [T] (in
this case, [01]).
To change or cancel a program
1
2
Follow Steps 1 to 3 of “Creating your
PROGRAM
0: 00:00
T
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
Press X/x to select the program
number of the track you want to
change or cancel.
– –
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
If you want to delete the track from the
program, press CLEAR.
3
Follow Step 5 for new programming.
To cancel a program, select [--] under [T],
then press
.
GB
46
Download from Www.Somanuals.com. All Manuals Search And Download.
* Except for North American models.
Press
Shuffle Play starts.
To cancel all of the tracks in the
programmed order
4
.
1
Follow Steps 1 to 3 of “Creating your
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
2
Press X and select [ALL CLEAR].
3
Press
.
To turn off the Control Menu
display
Note
• When you press CLEAR to return to normal play,
Shuffle Play and Repeat Play are also canceled.
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
Note
Playing in random order
(Shuffle Play)
• You cannot use Shuffle Play with a VIDEO CD or
Super VCD with PBC playback.
• When you press CLEAR to return to normal play,
Program Play and Repeat Play are also canceled.
You can play the contents on a disc in random
order. Subsequent Shuffle Play may produce a
different playing order.
Playing repeatedly
(Repeat Play)
Note
• The same song may be played repeatedly when you
are playing MP3 files.
• You can shuffle the tracks on the current disc only.
You can play the contents on a disc repeatedly.
You can use a combination of Shuffle Play or
Program Play modes.
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
1
2
3
Press
DISPLAY during playback.
Press X/x to select
then press
[SHUFFLE],
The Control Menu display appears on the
TV screen.
.
The options for [SHUFFLE] appear.
Press X/x to select
then press
[REPEAT],
Press X/x to select the item to be
shuffled.
.
The options for [REPEAT] appear.
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
Press X/x to select the item to be
repeated.
• [TRACK]: You can shuffle tracks on the
disc.
x DVD VIDEO/DVD-VR
• [OFF]: Off.
• [ALL DISCS]: You can repeat all of the
discs.
x During Program Play
• [OFF]: Off.
• [ON]: You can shuffle tracks selected in
Program Play.
• [ONE DISC]: You can repeat all of the
titles on the current disc. (When the
system is playing a DVD-VR, you can
repeat all of the titles of the selected disc.)
• [TITLE]: You can repeat the current title
on a disc.
x DATA CD (except for video files*)/
DATA DVD (except for video files*)
• [OFF]: Off.
• [ON (MUSIC)]: You can shuffle MP3
files in the folder on the current disc.
When no folder is selected, the first folder
will play in random order.
• [CHAPTER]: You can repeat the current
chapter on a disc.
GB
47
Download from Www.Somanuals.com. All Manuals Search And Download.
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
• [ALL DISCS]: You can repeat all of the
discs.
Searching/Selecting
Disc Contents
• [ONE DISC]: You can repeat all of the
tracks on the current disc.
• [TRACK]: You can repeat the current
track.
Using the DVD’s menu
x DATA CD/DATA DVD
• [OFF]: Off.
A DVD is divided into many sections, which
make up a picture or music feature. These
sections are called “titles.” When you play a
DVD which contains several titles, you can
select the title you want using DVD TOP
MENU.
When you play a DVD that allows you to select
items such as the language for the subtitles and
the language for the sound, select these items
using DVD MENU.
• [ALL DISCS]: You can repeat all of the
discs.
• [ONE DISC]: You can repeat all of the
folders on the current disc.
• [FOLDER]: You can repeat the current
folder.
• [TRACK] (MP3 files only): You can
repeat the current file.
• [FILE] (video files only): You can repeat
the current file (except for North
American models).
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary depending
on the disc.
4
Press
.
The item is selected.
2
3
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
Press
.
To turn off the Control Menu
display
To display the DVD’s menu on the
Control Menu display
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
1
Press
DISPLAY during playback.
Note
The Control Menu display appears on the
TV screen.
• You cannot use Repeat Play with a VIDEO CD or
Super VCD with PBC playback.
• When the system is playing a DATA CD/DATA
DVD which contains MP3 files and JPEG image
files, and their playing time is not the same, the audio
sound will not match the image.
2
Press X/x to select
MENU], then press
[DISC
.
The options for [DISC MENU] appear.
• When you press CLEAR to return to normal play,
Program Play and Shuffle Play are also canceled.
3
4
Press X/x to select [MENU] or [TOP
MENU].
Press
.
To turn off the Control Menu
display
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
GB
48
Download from Www.Somanuals.com. All Manuals Search And Download.
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, folders, or files.
Selecting an original title or
edited title on a DVD-VR
98( 99)
13( 99)
DVD VIDEO
T
0: 03: 17
This function is only available for DVD-VRs
with a playlist created.
1
2
3
Press
in stop mode.
DISPLAY while the system is
Selected row
The Control Menu display appears on the
TV screen.
3
4
Press
.
Press X/x to select
PLAY LIST], then press
[ORIGINAL/
.
[** (**)] changes to [– – (**)].
The options for [ORIGINAL/PLAY LIST]
appear.
98( 99)
( 99)
T
DVD VIDEO
0: 03: 17
Press X/x to select a setting.
• [PLAY LIST]: You can play the titles in
the order of the existing playlist.
• [ORIGINAL]: You can play the titles
originally recorded.
4
Press
.
Press X/x or the number buttons to
select the desired number of the title,
chapter, track, index, scene, etc.
Searching for a title/chapter/
track/scene, etc.
If you make a mistake, press CLEAR to
cancel the number.
5
Press
.
The system starts playback from the
selected number.
You can search a DVD VIDEO/DVD-VR by
title or chapter, and you can search a VIDEO
CD/Super Audio CD/CD/DATA CD/DATA
DVD by track, index, or scene. For a DATA CD/
DATA DVD, you can search by folder or file.
As titles and tracks are assigned unique numbers
on the disc, you can select the desired title or
track by entering its number. Or, you can search
for a scene using the time code.
Tip
• When the Control Menu display is turned off, you can
search for a chapter (DVD VIDEO/DVD-R/DVD-
RW), track (VIDEO CD/Super Audio CD/CD), or
file (DATA CD/DATA DVD (video file))* by
pressing the number buttons and
.
* Except for North American models.
To search for a scene using the
time code
1
Press
DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press
twice.)
DISPLAY
1
2
In Step 2, select
[TIME].
[T **:**:**] (playing time of the current
title) is selected.
The Control Menu display appears on the
TV screen.
Press
.
2
Press X/x to select the search method.
[T **:**:**] changes to [T --:--:--].
Example:
[CHAPTER]
[** (**)] is selected (** refers to a number).
GB
49
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Input the time code using the number
buttons.
Playing MP3 Files/JPEG
Image Files
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds after the
beginning: press 2, 1, 0, 2, 0 ([2:10:20]).
4
Press
.
You can play MP3 files or JPEG image files:
Note
• You cannot search for a scene on a DVD+RW using
the time code.
– which have the extension “.mp3” (MP3 file)
or “.jpg”/“.jpeg” (JPEG image file).
– which conform to the DCF* image file
format.
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan
Electronics and Information Technology Industries
Association (JEITA).
Note
• The system will play any files with the extension
“.mp3,” “.jpg,” or “.jpeg” even if they are not in MP3
or JPEG format. Playing these files may generate a
loud noise which could damage your speaker system.
• The system does not play back audio in MP3PRO
format.
• The system can recognize up to 200 folders, and will
not play any folders beyond the 200th. (Depending on
the folder configuration, the number of folders that
can be recognized by the system may decrease.)
• The system can recognize up to 150 MP3 files/JPEG
image files in a folder.
• The system may take a longer time to play files when
progressing to the following folder or jumping to
other folders.
• The system may not play certain types of JPEG image
files (ex. a JPEG image file that is less than 8 (width)
× 8 (height)).
• Depending on the area, the [MEDIA] icon appears as
follows:
–
–
: North American models
: Other models
Selecting an MP3 file or folder
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders
appears on the TV screen.
GB
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
Press
DISPLAY.
To stop playback
The Control Menu display appears on the
TV screen.
Press x.
To play the next or previous MP3
file
Press X/x to select
then press
[MEDIA],
.
Press > to play the next MP3 file. Press .
twice to play the previous MP3 file.
When you press . once, you can go to the
beginning of the current MP3 file.
Note that you can select the next folder by
continuing to press > after the last file on the
current folder, but that you cannot return to the
previous folder by pressing .. To return to
the previous folder, select the folder from the
folder list.
The options for [MEDIA] appear.
When [MUSIC] is selected, press DVD
MENU. When other than [MUSIC] is
selected, press X/x to select [MUSIC],
then press
.
A list of folders that contain MP3 files
appears.
The selected folder is highlighted in yellow.
FOLDER LIST
To return to the previous display
01 Let's Talk About Love (1985)
02 1st Album (1986)
Press O RETURN.
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
To turn on/off the display
Press DVD MENU.
08 Alone (1999)
Other operations
6
Press X/x to select a folder.
x To play MP3 files in a folder
Press H to start playing the selected
folder.
Selecting a JPEG image file or
folder
x To select an MP3 file
Press
.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
The list of files contained in the folder
appears.
2
Load a DATA CD or DATA DVD.
TRACK LIST
After loading the disc, the list of folders
appears on the TV screen.
03 In the Middle of Nowher...
01_Geronimo_s_Cadillac
02_Riding_On_A_White_Swan
03_Give_Me_Peace_On_Earth
04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
06_Lonely_Tears_In_Chinatown
07_In_Shaire
3
4
5
Press
DISPLAY.
The Control Menu display appears on the
TV screen.
Press X/x to select
then press
[MEDIA],
.
Press X/x to select a file and press
.
The options for [MEDIA] appear.
The system starts playing the selected file.
You can turn the file list off by pressing
DVD MENU. Pressing DVD MENU again
will display the folder list.
When [PHOTO] is selected, press DVD
MENU. When other than [PHOTO] is
selected, press X/x to select [PHOTO],
then press
.
To go to the next or previous
page
A list of folders that contain JPEG files
appears.
Press
/
.
The selected folder is highlighted in yellow.
GB
51
Download from Www.Somanuals.com. All Manuals Search And Download.
To rotate a JPEG image file
FOLDER LIST
When a JPEG image file is displayed on the TV
screen, you can rotate the JPEG image file in 90
degree increments.
Press X/x while viewing a JPEG image file.
Press CLEAR to return to normal view.
01 Happy birthday
02 Travelling 01
03 2003.08.20
04 Flowers
05 Travelling 02
06 Animals
07 2003.11.16
08 2003.12.03
Note
• You cannot rotate the JPEG image file when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
6
Press X/x to select a folder.
× 1080i) HD
x To go to the next or previous page
To stop playback
Press
/
.
Press x.
x To play JPEG image files in a folder
Press H to start playing the selected
folder.
To turn on/off the display
Press DVD MENU.
The JPEG images are played as a slide
show. You can change the interval of the
Other operations
x To select a JPEG image file by
displaying the image browser
Press PICTURE NAVI.
Previews of JPEG image files in the folder
appear in 16 subscreens.
Playing a slide show with
sound
You can play a slide show with sound by first
placing both MP3 files and JPEG image files in
the same folder on a DATA CD or DATA DVD.
1
2
3
4
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
5
6
7
8
9
10
14
11
15
12
16
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders
appears on the TV screen.
13
Press C/X/x/c to select the JPEG image
file you want to view, then press
To return to the previous screen, press O
3
4
5
Press
DISPLAY.
.
The Control Menu display appears on the
TV screen.
RETURN.
Press X/x to select
then press
[MEDIA],
To play the next or previous JPEG
image file
.
The options for [MEDIA] appear.
Press c/C when the Control Menu display is not
displayed. Note that you can select the next
folder by continuing to press c after the last
image on the current folder, but that you cannot
return to the previous folder by pressing C. To
return to the previous folder, select the folder
from the folder list.
When [MUSIC/PHOTO] is selected,
press DVD MENU. When other than
[MUSIC/PHOTO] is selected, press X/x
to select [MUSIC/PHOTO], then press
.
The list of folders appears.
GB
52
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press X/x to select the desired folder
and press H.
Selecting an effect for JPEG
image files in the slide show
The system starts playing the selected
folder.
You can turn the folder list on/off by
pressing DVD MENU repeatedly.
1
Press
DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press
twice.)
DISPLAY
Note
The Control Menu display appears on the
TV screen.
• If you play a large MP3 file and JPEG image file at
the same time, the sound may skip. Sony
recommends that you set the MP3 bit rate to 128 kbps
or lower when creating the file. If the sound still
skips, reduce the size of the JPEG image file.
2
3
Press X/x to select
then press
[EFFECT],
.
The options for [EFFECT] appear.
Press X/x to select a setting.
Selecting the slide show
duration of JPEG image files
• [MODE 1]: The JPEG image file sweeps
in from top to bottom.
• [MODE 2]: The JPEG image file stretches
out from left to right of the TV screen.
• [MODE 3]: The JPEG image file stretches
out from the center of the TV screen.
• [MODE 4]: The JPEG image files
randomly cycle through the effects.
• [MODE 5]: The next JPEG image file
slides over the previous image.
1
Press
DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press
twice.)
DISPLAY
The Control Menu display appears on the
TV screen.
2
3
Press X/x to select
then press
[INTERVAL],
.
• [OFF]: Off.
The options for [INTERVAL] appear.
4
Press
.
Press X/x to select a setting.
• [NORMAL]: You can set to the standard
duration.
Note
• The [EFFECT] setting is not effective when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
• [FAST]: You can set the duration shorter
than [NORMAL].
× 1080i) HD
• [SLOW 1]: You can set the duration
longer than [NORMAL].
• [SLOW 2]: You can set the duration
longer than [SLOW 1].
Selecting playback priority of
the file type
4
Press
.
You can select playback priority when mixed
media (MP3 files, JPEG image files, or video
files*) are in the disc.
Note
• Some JPEG image files may take longer to display
than the option you selected. Especially progressive
JPEG image files or JPEG image files of 3,000,000
pixels or more.
* Except for North American models.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders
appears on the TV screen.
GB
53
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
Press
DISPLAY.
The Control Menu display appears on the
TV screen.
Enjoying Video Files
Press X/x to select
then press
[MEDIA],
.
(Except for North American models)
The options for [MEDIA] appear.
Press X/x to select a setting.
About video files
• [MUSIC/PHOTO]: You can play both
JPEG image files and MP3 files in the
same folder as a slide show.
You can play DivX video files and MPEG4
video files.
• [MUSIC]: MP3 file playback has priority.
• [VIDEO] (Except for North American
models): Video file playback has priority.
• [PHOTO]: JPEG image file playback has
priority. You can play JPEG image files as
a slide show.
®
DivX is a video file compression technology,
developed by DivX, Inc. This product is an
®
official DivX Certified product.
You can play a DATA CD or DATA DVD that
®
contains DivX video files.
A DATA CD or DATA DVD that the
system can play
6
Press
.
For details of the playback priority of file
types under the [MEDIA] setting, see
The system only plays a DATA CD of format
ISO 9660 Level 1/Level 2 or Joliet, and a DATA
DVD of Universal Disk Format (UDF).
Refer to the operating instructions supplied with
the disc drives and the recording software (not
supplied) for details on the recording format.
Displaying a list of MP3 files/
JPEG image files
About playback order of data on a
DATA CD or DATA DVD
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
Note that the playback order may not be
applicable, depending on the software used for
creating the video file, or if there are more than
200 folders and 150 video files in each folder.
Press X/x to select
[BROWSING], then press
.
Note
The options for [BROWSING] appear.
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
Press X/x to select the desired list,
then press
.
• [FOLDER LIST]: The list of folders
appears. Follow Step 6 of “Selecting an
DivX video files that the system
can play
The system can play data that is recorded in
DivX format, and which has the extension “.avi”
or “.divx.” The system will not play files with
the extension “.avi” or “.divx” if they do not
contain a DivX video.
• [PICTURE LIST] (JPEG image files
only): Previews of JPEG image files in the
folder appear in 16 subscreens. Follow
Step 6 of “Selecting a JPEG image file or
Note
• The system may not play a DivX video file when the
file has been combined from two or more DivX video
files.
GB
54
Download from Www.Somanuals.com. All Manuals Search And Download.
• The system cannot play a DivX video file of size
more than 720 (width) × 576 (height) or 2GB.
• Depending on the DivX video file, sound may skip or
not match the pictures on the TV screen.
A list of folders that contain video files
appears.
The selected folder is highlighted in yellow.
• The system cannot play some DivX video files that
are longer than 3 hours.
FOLDER LIST
SUMMER 2003
• Depending on the DivX video file, the picture may
pause or be unclear, in which case it is recommended
that you create the file at a lower bit rate. If the sound
is still noisy, MP3 is the recommended audio format.
Note, however, this system does not conform to
WMA (Windows Media Audio) format for playing
DivX files.
NEW YEAR'S DAY
MY FAVOURITES
• Because of the compression technology used for
DivX video files, it may take some time after you
press H for the picture to appear.
6
7
Press X/x to select the folder you want
to play.
Press H.
MPEG4 video files that the
system can play
The system starts playing the selected
folder.
To select video files, see “Selecting a video
The system can play data that is recorded in
MP4 file format, and which has the extension
“.mp4” or “.m4v.” The system will not play files
with the extension “.mp4” or “.m4v” if they do
not contain a MPEG4 video.
To go to the next or previous
page
Press
/
.
Note
• Compatibility with all MPEG4 video encoding/
writing software, recording devices, and recording
media cannot be guaranteed.
To stop playback
Press x.
To turn on/off the display
Press DVD MENU.
Selecting a folder
Other operations
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Load a DATA CD or DATA DVD.
Selecting a video file
After loading the disc, the list of folders
appears on the TV screen.
1
press
.
3
4
5
Press
DISPLAY.
The list of files in the folder appears.
The Control Menu display appears on the
TV screen.
FILE LIST
MY FAVOURITES
Press X/x to select
then press
[MEDIA],
.
HAWAII 2004
VENUS
The options for [MEDIA] appear.
When [VIDEO] is selected, press DVD
MENU. When other than [VIDEO] is
selected, press X/x to select [VIDEO],
then press
.
2
Press X/x to select a file and press
.
The selected file starts playing.
GB
55
Download from Www.Somanuals.com. All Manuals Search And Download.
To go to the next or previous
page
Adjusting the Delay
Between the Picture and
Sound
Press
/
.
To return to the previous display
Press O RETURN.
[A/V SYNC]
To stop playback
*
*
Press x.
* Except for North American models
To play the next or previous video
file without turning on the above
file list
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
You can select the next or previous video file in
the same folder by pressing >/..
You can also select the first file of the next
folder by pressing > during playback of the
last file of the current folder. Note that you
cannot return to the previous folder by pressing
.. To return to the previous folder, select it
from the folder list.
1
2
3
Press
DISPLAY.
The Control Menu display appears on the
TV screen.
Press X/x to select
then press
[A/V SYNC],
.
The options for [A/V SYNC] appear.
Tip
Press X/x to select a setting.
• If the number of viewing times is preset, you can play
a DivX video file as many times as the preset number.
The following occurrences are counted:
• [OFF]: Off.
• [ON]: You can adjust the delay between
picture and sound.
– when the system is turned off.
– when another file is played.
– when the disc tray is opened.
4
Press
.
Note
• Depending on the input stream, [A/V SYNC] may not
be effective.
Displaying a list of video files
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
Press X/x to select
[BROWSING], then press
.
The options for [BROWSING] appear.
Press X/x to select [FOLDER LIST],
then press
.
The list of folders appears. Follow Step 6 of
GB
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter a 4-digit password using the number
buttons, then press
.
Restricting Playback of
the Disc
The display for confirming the password
appears.
x When you have already registered a
password
[PARENTAL CONTROL]
The display for entering the password
appears.
The [PARENTAL CONTROL] function allows
you to restrict playback of DVDs that have
ratings. Scenes may be blocked or replaced with
different scenes.
You can set the playback restriction by
registering a password. When you set the
[PARENTAL CONTROL] function to on, you
need to enter the password to play restricted
discs.
7
Enter or re-enter your 4-digit password
using the number buttons, then press
.
The display for setting the playback
limitation level appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD:
OFF
USA
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
8
9
Press X/x to select [STANDARD], then
press
The Control Menu display appears on the
TV screen.
.
The selection items for [STANDARD] are
displayed.
3
4
5
6
Press X/x to select
then press
[SETUP],
.
Press X/x to select a geographic area
as the playback limitation level, then
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
press
.
The area is selected.
The Setup Display appears.
When you select [OTHERS t], select and
enter a standard code from “Parental
the number buttons.
Press X/x to select [SYSTEM SETUP],
then press
.
The options for [SYSTEM SETUP] appear.
10
11
Press X/x to select [LEVEL], then press
Press X/x to select [PARENTAL
.
CONTROL t], then press
.
The selection items for [LEVEL] are
displayed.
x If you have not entered a password
The display for registering a new password
appears.
Press X/x to select the desired level,
then press
.
PARENTAL CONTROL
[PARENTAL CONTROL] setting is
complete.
The lower the value, the stricter the
limitation.
Enter a new 4-digit password,
ENTER
then press
.
GB
57
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Enter your 4-digit password using the
To turn off the [PARENTAL
CONTROL] function
number buttons, then press
.
8
Press X/x to select [CHANGE
PASSWORD t], then press
Set [LEVEL] to [OFF] in Step 11.
.
To play a disc for which
[PARENTAL CONTROL] is set
9
Enter a new 4-digit password using the
number buttons, then press
.
1
2
Tip
Load the disc and press H.
10
To confirm your password, re-enter it
using the number buttons, then press
.
The display for entering your password
appears.
Enter your 4-digit password using the
number buttons, then press
If you make a mistake entering
your password
.
The system starts playback.
Press C before you press , then input the
correct number.
• If you forget your password, remove the disc and
repeat Steps 1 to 6 of “Restricting Playback of the
Disc” (page 57). When you are asked to enter your
password, enter “199703” using the number buttons,
then press . The display will ask you to enter a new
4-digit password. After you enter a new 4-digit
password, replace the disc in the unit and press H.
When the display for entering your password appears,
enter your new password.
Changing the password
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
3
4
5
6
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
Press X/x to select [SYSTEM SETUP],
then press
.
The options for [SYSTEM SETUP] appear.
Press X/x to select [PARENTAL
CONTROL t], then press
.
The display for entering the password
appears.
GB
58
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Press X/x to select an item, then press
.
Changing the System
Settings by Using the
Setup Display
You can make various adjustments to items such
as picture and sound.
Displayed items vary depending on the area.
The options for the selected item appear.
Example: [TV TYPE]
VIDEO SETUP
TV TYPE:
16:9
16:9
PROGRESSIVE (COMPON
4:3 OUTPUT:
BLACK LEVEL:
4:3 LETTER BOX
4:3 PAN SCAN
BLACK LEVEL (COMPONENT OUT):
PAUSE MODE:
OFF
AUTO
Options
Note
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
Press X/x to select a setting, then
press
.
1
2
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
The setting is selected and setup is
complete.
Example: [4:3 LETTER BOX]
Press
DISPLAY while the system is
VIDEO SETUP
TV TYPE:
in stop mode.
4:3 LETTER BOX
The Control Menu display appears on the
TV screen.
PROGRESSIVE (COMPONENT OUT):
4:3 OUTPUT:
BLACK LEVEL:
OFF
FULL
ON
BLACK LEVEL (COMPONENT OUT):
PAUSE MODE:
OFF
AUTO
3
4
5
Press X/x to select
then press
[SETUP],
.
Selected setting
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
To reset all of the [SETUP]
settings
press
.
The Setup Display appears.
To reset all of the [SETUP] settings, see
Press X/x to select the setup item, then
press
.
• [LANGUAGE SETUP] (page 59)
• [VIDEO SETUP] (page 60)
• [HDMI SETUP] (page 62)
Setting the display or sound
track language
• [AUDIO SETUP] (page 63)
• [SYSTEM SETUP] (page 64)
• [SPEAKER SETUP] (page 64)
[LANGUAGE SETUP]
Example: [VIDEO SETUP]
Set various languages for the on-screen display
or sound track.
Selected item
VIDEO SETUP
LANGUAGE SETUP
TV TYPE:
16:9
OFF
FULL
ON
OSD:
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
PROGRESSIVE (COMPONENT OUT):
4:3 OUTPUT:
BLACK LEVEL:
MENU:
AUDIO:
SUBTITLE:
BLACK LEVEL (COMPONENT OUT):
PAUSE MODE:
OFF
AUTO
Setup items
GB
59
Download from Www.Somanuals.com. All Manuals Search And Download.
x [OSD] (On-Screen Display)
You can switch the display language on the TV
screen.
x [TV TYPE]
You can select the aspect ratio of the connected
TV.
[16:9]: Select this when you connect a wide-
screen TV or a TV with a wide mode function.
x [MENU] (DVD VIDEO only)
You can switch the language for the disc’s
menu.
x [AUDIO] (DVD VIDEO only)
You can switch the language of the sound track.
When you select [ORIGINAL], the language
given priority on the disc is selected.
[4:3 LETTER BOX]: Select this when you
connect a 4:3 standard TV. The system displays
a wide picture with bands on the upper and
lower portions of the TV screen.
x [SUBTITLE] (DVD VIDEO only)
You can switch the language of the subtitles
recorded on the DVD VIDEO.
When you select [AUDIO FOLLOW], the
language for the subtitles changes according to
the language you selected for the sound track.
[4:3 PAN SCAN]: Select this when you connect
a 4:3 standard TV. The system automatically
displays a wide picture on the entire screen and
cuts off the portions that do not fit.
Note
• When you select a language in [MENU], [AUDIO],
or [SUBTITLE] that is not recorded on the DVD
VIDEO, one of the recorded languages will be
automatically selected (depending on the disc, the
language may not be selected automatically).
Tip
• If you select [OTHERS t] in [MENU], [AUDIO],
and [SUBTITLE], select and enter a language code
number buttons.
Note
• Depending on the DVD, [4:3 LETTER BOX] may be
selected automatically instead of [4:3 PAN SCAN] or
vice versa.
Settings for the display
[VIDEO SETUP]
x [PROGRESSIVE (COMPONENT OUT)]
You can set the progressive signal that is output
from the COMPONENT VIDEO OUT jacks to
on/off. For details, see “Does your TV accept
Select settings according to the TV to be
connected.
VIDEO SETUP
TV TYPE:
16:9
OFF
FULL
ON
[OFF]: The system outputs interlace signals.
[ON]: The system outputs progressive signals.
When you select [ON], follow the Steps below.
PROGRESSIVE (COMPONENT OUT):
4:3 OUTPUT:
BLACK LEVEL:
BLACK LEVEL (COMPONENT OUT):
PAUSE MODE:
OFF
AUTO
1
2
Select [ON], then press
.
The confirmation display appears.
Press C/c to select [START], then
press
.
GB
60
Download from Www.Somanuals.com. All Manuals Search And Download.
The system outputs a progressive signal for
5 seconds. Check that the screen is
displayed correctly.
Note
• You cannot change the color system of the disc itself.
• You can change the color system of this system
3
Press C/c to select [YES], then press
.
x [BLACK LEVEL]
The system outputs a progressive signal. If
you select [NO], the system will not output
a progressive signal.
(North American, Mexican, and Latin
American models only)
You can select the black level (setup level) for
the video signals output from the jacks other
than COMPONENT VIDEO OUT/HDMI OUT.
Note
• [PROGRESSIVE (COMPONENT OUT)] is
effective only when you connect the unit and TV with
[ON]: The standard level.
[OFF]: You can lower the standard black level.
Use this when the picture becomes too white.
x [4:3 OUTPUT]
When you use a 16:9 aspect ratio TV, you can
adjust the aspect ratio to watch 4:3 aspect ratio
signals. If you can change the aspect ratio on
your TV, change the setting on your TV, not the
system.
x [BLACK LEVEL (COMPONENT OUT)]
(North American, Mexican, and Latin
American models only)
You can select the black level (setup level) for
the video signals output from the
COMPONENT VIDEO OUT jacks.
You cannot select this and the setting is not
effective when the system outputs a progressive
signal.
[FULL]: Select this when you can change the
aspect ratio on your TV.
[NORMAL]: Select this when you cannot
change the aspect ratio on your TV. A 16:9
aspect ratio signal with black bands on left and
right sides of the image appears.
[OFF]: You can set the black level of the output
signal to the standard level.
[ON]: You can raise the standard black level.
Use this when the picture becomes too black.
16:9 aspect ratio TV
x [PAUSE MODE] (DVD VIDEO/DVD-R/
DVD-RW only)
Note
You can select the picture in pause mode.
• [4:3 OUTPUT] is effective only when you set [TV
TYPE] in [VIDEO SETUP] to [16:9].
[AUTO]: The picture, including subjects that
move dynamically, is output with no jitter. This
setting is for normal usage.
[FRAME]: The picture, including subjects that
do not move dynamically, is output in high
resolution.
x [COLOR SYSTEM (VIDEO CD)]
(Asian, Australian, and Middle Eastern
models only)
You can select the color system when you play a
VIDEO CD.
[AUTO]: The system outputs the disc’s video
signal, either PAL or NTSC. If your TV uses a
DUAL system, select [AUTO].
[PAL]: The system changes the video signal of
an NTSC disc and outputs it in the PAL system.
[NTSC]: The system changes the video signal of
a PAL disc and outputs it in the NTSC system.
GB
61
Download from Www.Somanuals.com. All Manuals Search And Download.
sound may be output depending on the volume
level of the system. You can prevent this by
limiting the maximum level of the volume.
* The button name differs depending on the area.
Settings for HDMI
[HDMI SETUP]
HDMI SETUP
[LEVEL3]: Maximum volume level is set to 10.
[LEVEL2]: Maximum volume level is set to 15.
[LEVEL1]: Maximum volume level is set to 20.
[OFF]: Off.
HDMI RESOLUTION:
CONTROL FOR HDMI:
VOLUME LIMIT:
AUTO(1920x1080p)
ON
LEVEL2
YCBCR
OFF
SD
YCB
C
R/RGB(HDMI):
AUDIO(HDMI):
JPEG RESOLUTION:
Note
• This function is available only when [CONTROL
FOR HDMI] is set to [ON].
x [HDMI RESOLUTION]
x [YCBCR/RGB (HDMI)]
You can select the type of video signal that is
output from the HDMI OUT jack. For details,
You can select the type of HDMI signal output
from the HDMI OUT jack.
[YCB
C
R]: The system outputs YCB
C
R
signals.
[RGB]: The system outputs RGB signals.
[AUTO (1920 × 1080p)]: The system outputs
the optimal video signal for the connected TV.
[1920 × 1080i]: The system outputs 1920 ×
1080i* video signals.
[1280 × 720p]: The system outputs 1280 ×
720p* video signals.
Note
• If the playback picture becomes distorted, set
[YCBCR] to [RGB].
• If the HDMI OUT jack is connected to a component
with a DVI jack, [RGB] signals will be automatically
output even when you select [YCBCR].
[720 × 480p]**: The system outputs 720 ×
480p* video signals.
x [AUDIO (HDMI)]
You can select the audio output status from the
HDMI OUT jack.
* i: interlace, p: progressive
**Depending on the area, [720 × 480/576p] may
appear.
[OFF]: The system does not output sound from
the HDMI OUT jack.
[ON]: The system outputs audio signals by
converting Dolby Digital, DTS, or 96 kHz/24-
bit PCM signals to 48 kHz/16-bit PCM.
x [CONTROL FOR HDMI]
You can set the [CONTROL FOR HDMI]
function to on/off. This function is available
when you connect the system and TV with an
HDMI cable. For details, see “Using the Control
Note
• When you connect the unit and TV with an HDMI
cable and [ON] is selected, [AUDIO DRC], [A/V
SYNC], DYNAMIC BASS, “DEC. MODE,” and
sound mode are not applied to the sound that is output
from the TV.
[ON]: On. You can operate mutually between
components that are connected with an HDMI
cable.
[OFF]: Off.
• When you set the function to other than “DVD,” the
system does not output the sound from the HDMI
OUT jack even if you set [AUDIO (HDMI)] to [ON].
x [VOLUME LIMIT]
x [JPEG RESOLUTION]
You can select the resolution of JPEG image
files output from the HDMI OUT jack.
If you change the output method of the TV to the
system speakers via the TV menu (or by
pressing THEATER/THEATRE*), the System
GB
62
Download from Www.Somanuals.com. All Manuals Search And Download.
[SD
]: The system outputs standard
x [AUTO CALIBRATION]
resolution with a black frame.
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
[HD
]: The system outputs HD resolution
with a black frame.
[HD]: The system outputs the HD resolution
without a black frame.
x [AUDIO DRC] (DVD VIDEO only)
[(1920 × 1080i) HD
]: The system outputs
You can compress the dynamic range of the
sound track. [AUDIO DRC] is useful for
watching movies at low volume late at night.
full size HD resolution with a black frame.
[(1920 × 1080i) HD]: The system outputs full
size HD resolution without a black frame.
Note
[OFF]: No compression of dynamic range.
[STANDARD]: The system reproduces the
sound track with the kind of dynamic range that
the recording engineer intended.
• [JPEG RESOLUTION] is effective only when you
set [TV TYPE] in [VIDEO SETUP] to [16:9], and
you set [HDMI RESOLUTION] in [HDMI SETUP]
to other than [720 × 480p] or [720 × 480/576p].
[MAX]: The system compresses dynamic range
fully.
• You can select [(1920 × 1080i) HD
1080i) HD] only when you set [HDMI
] or [(1920 ×
RESOLUTION] in [HDMI SETUP] to [1920 ×
1080i].
Note
• [AUDIO DRC] works only for Dolby Digital.
• The HDMI signal will stop momentarily when:
– the system is loading or unloading a DATA CD or
DATA DVD.
x [TRACK SELECTION] (DVD VIDEO only)
You can give the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, DTS, Dolby Digital, or MPEG
audio) are recorded.
– you change the disc from a DATA CD or DATA
DVD.
– you play a DATA CD or DATA DVD to the end
and the system stops playback automatically.
Settings for the audio
[AUDIO SETUP]
[OFF]: Off.
[AUTO]: The system selects the sound track
automatically according to the priority.
Note
• When you set the item to [AUTO], the language may
change. The [TRACK SELECTION] setting has
higher priority than the [AUDIO] settings in
the disc, this function may not work.)
• If PCM, DTS, Dolby Digital sound, and MPEG audio
have the same number of channels, the system selects
PCM, DTS, Dolby Digital sound, and MPEG audio in
this order.
AUDIO SETUP
SPEAKER FORMATION:
AUTO CALIBRATION:
AUDIO DRC:
TRACK SELECTION:
OFF
OFF
x [SPEAKER FORMATION]
You can select the position of the speakers for
better surround sound. For details, see “Getting
GB
63
Download from Www.Somanuals.com. All Manuals Search And Download.
x [MULTI-DISC RESUME] (DVD VIDEO/
VIDEO CD only)
You can set the [MULTI-DISC RESUME]
function to on/off.
Other Settings
[SYSTEM SETUP]
SYSTEM SETUP
SCREEN SAVER:
BACKGROUND:
PARENTAL CONTROL:
DivX:
MULTI-DISC RESUME:
RESET:
[ON]: The system stores the resume points in
memory for up to 10 discs.
[OFF]: The system does not store the resume
points in memory. Playback restarts at the
resume point only for the current disc in the unit.
ON
JACKET PICTURE
Registration Code
ON
x [RESET]
You can return the [SET UP] settings other than
[PARENTAL CONTROL] to the default
settings. For details, see “Returning the
x [SCREEN SAVER]
You can reduce the damage to the display device
(ghosting). Press any button (e.g.,
the screen saver.
H) to cancel
Settings for the speakers
[SPEAKER SETUP]
[ON]: The screen saver image appears if you do
not operate the system for about 15 minutes.
[OFF]: Off.
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
x [BACKGROUND]
You can select the background color or picture
on the TV screen.
[JACKET PICTURE]: The jacket picture (still
picture) appears, but only when the jacket
picture is already recorded on the disc (CD-
EXTRA, etc.). If the disc does not contain a
jacket picture, the [GRAPHICS] picture
appears.
SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT)
:
DISTANCE(SURROUND):
LEVEL(FRONT):
LEVEL(SURROUND):
TEFRONT:
CENTER:
SURROUND:
YES
YES
YES
YES
[GRAPHICS]: A preset picture stored in the
system appears.
SUBWOOFER:
[BLUE]: The background is blue.
[BLACK]: The background is black.
x [CONNECTION]
If you do not connect center or surround
speakers, set the parameters for [CENTER] and
[SURROUND]. Since the front speaker and
subwoofer settings are fixed, you cannot change
them.
x [PARENTAL CONTROL]
You can set the playback restrictions. For
details, see “Restricting Playback of the Disc”
[FRONT]
x [DivX]
[YES]
(Except for North American models)
You can display the registration code for this
system.
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center speaker is used.
For more information, go to
http://www.divx.com on the Internet.
GB
64
Download from Www.Somanuals.com. All Manuals Search And Download.
[SURROUND]
x [DISTANCE (SURROUND)]
[YES]: Normally select this.
[NONE]: Select this if no surround speakers are
used.
When you move the surround speakers, be sure
to set the parameters of the distance (B) from
the listening position to the speakers.
[SUBWOOFER]
You can set the parameters from 0.0 to 7.0
[YES]
1)
meters (0 to 23 ft).
Note
• When you change the [CONNECTION] setting, the
[STANDARD] of [SPEAKER FORMATION]
setting remains the same, but the other settings of
[SPEAKER FORMATION] return to
[STANDARD].
x [DISTANCE (FRONT)]
B
When you move the front speakers and center
speaker, be sure to set the parameters of the
distance (A) from the listening position to the
speakers.
You can set the parameters from 1.0 to 7.0
1)
meters (3 to 23 ft) for the front speakers, from
2)
0.0 to 7.0 meters (0 to 23 ft) for the center
speaker.
[L/R] 3.0 m/10 ft2)3): Set the surround speaker
distance (up to 5.0 meters (16 ft) closer to the
front speakers).
1)0.0 to 6.9 meters for North American models.
default settings are changed.
3)This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
A
Note
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
• Depending on the input stream, the [DISTANCE]
setting may not be effective.
[L/R] 3.0 m/10 ft3): Set the front speaker
distance.
[CENTER] 3.0 m/10 ft3)4): Set the center speaker
distance (up to 1.6 meters (5 ft) closer to the
front speakers).
x [LEVEL (FRONT)]
You can adjust the sound level of the front
speakers, center speaker, and subwoofer. You
can set the parameters from –6.0 dB to 0 dB for
[L/R], and from –6.0 dB to +6.0 dB for
[CENTER] and [SUBWOOFER]. Be sure to set
[TEST TONE] to [ON] for easy adjustment.
1)0.9 to 6.9 meters for North American models.
2)0.0 to 6.9 meters for North American models.
default settings are changed.
4)This item appears when you set [CENTER] to [YES]
in the [CONNECTION] setting.
[L/R] 0.0 dB: Set the front speaker level.
[CENTER] 0.0 dB*: Set the center speaker
level.
GB
65
Download from Www.Somanuals.com. All Manuals Search And Download.
[SUBWOOFER] +2.0 dB: Set the subwoofer
level.
* This item appears when you set [CENTER] to
[YES] in the [CONNECTION] setting.
x [LEVEL (SURROUND)]
You can adjust the sound level of the surround
speakers. You can set the parameter from –6.0
dB to +6.0 dB. Be sure to set [TEST TONE] to
[ON] for easy adjustment.
[L/R] 0.0 dB*: Set the surround speaker level.
* This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
x [TEST TONE]
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
[OFF]: The test tone is not emitted from the
speakers.
[ON]: The test tone is emitted from each speaker
in sequence while adjusting the level. When you
select one of the [SPEAKER SETUP] items, the
test tone is emitted from each speaker in
sequence.
Adjust the sound level as follows.
1
2
Set the [TEST TONE] to [ON].
Press C/X/x/c repeatedly to select the
desired speaker and the level.
3
4
5
Press
.
Repeat Steps 1 to 3.
Press C/X/x/c repeatedly to set [TEST
TONE] to [OFF] after adjusting the
speaker level.
Tip
• To adjust the volume of all the speakers at one time,
turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
• To return to the default setting when changing a
setting, select the item, then press CLEAR. Note that
only the [CONNECTION] setting does not return to
the default setting.
GB
66
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Press
.
“COMPLETE” appears in the front panel
display, and the station is stored.
Tuner
8
9
Repeat Steps 2 to 7 to store other
stations.
Presetting Radio
Stations
Press SYSTEM MENU.
The system menu turns off.
You can preset 20 FM stations, and 10 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
To change the preset number
Select the desired preset number by pressing
procedure from Step 3.
Current station
Current band and preset number
To change the AM tuning interval
(except for CIS and Middle
Eastern models)
FM
FM 10 : 88.00 MHz
SONY RADIO
The AM tuning interval can be set to either
10 kHz or 9 kHz.
To change the AM tuning interval, first tune in
any AM station, then turn off the system by
pressing "/1 on the unit. Press "/1 on the unit
while pressing > on the unit. The tuning
interval changes. If you change the interval, AM
preset stations will be erased.
Station name
1
2
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Press and hold TUNING +/– until the
auto scanning starts.
To reset the interval, repeat the same procedure.
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (stereo
program) appear in the front panel display.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “MEMORY”
appears in the front panel display.
5
Press
or c.
A preset number appears in the front panel
display.
6
Press X/x to select the preset number
you want.
Tip
• You can select the preset number directly by
pressing the number buttons.
GB
67
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press X/x repeatedly until “FM MODE”
appears in the front panel display.
Listening to the Radio
Preset radio stations in the system’s memory
3
4
Press
or c.
1
2
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Press X/x to select “MONO.”
• “STEREO”: Stereo reception.
• “MONO”: Monaural reception.
The last received station is tuned in.
Press PRESET +/– repeatedly to select
the preset station.
5
6
Press
.
The setting is made.
Each time you press the button, the system
tunes in one preset station.
Press SYSTEM MENU.
The system menu turns off.
Tip
• You can select the preset station number directly
by pressing the number buttons.
Naming preset stations
3
Adjust the volume by pressing
VOLUME +/–.
You can enter a name for preset stations. These
names (for example, “ABC”) appear in the front
panel display when a station is selected.
Only one name can be entered for each preset
station.
To turn off the radio
Press "/1.
To listen to non-preset radio
stations
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING +/–
repeatedly.
The last received station is tuned in.
For automatic tuning, press and hold TUNING
+/–. The automatic tuning stops automatically
when the system receives the radio station. To
stop the automatic tuning manually, press
TUNING +/– or x.
2
Press PRESET +/– repeatedly to select
the preset station you want to create an
index name for.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “NAME IN”
appears in the front panel display.
To listen to radio stations when
you know the frequencies
Press D.TUNING in Step 2, press the number
buttons to select the frequencies, then press
.
Tip
5
6
Press
or c.
• To improve reception, reorient the connected
antennas (aerials).
Create a name by using C/X/x/c.
Press X/x to select a character, then press c
to move the cursor to the next position.
If an FM program is noisy
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
You can input letters, numbers, and other
symbols for a radio station.
1
Press SYSTEM MENU.
GB
68
Download from Www.Somanuals.com. All Manuals Search And Download.
When the station name is not set
1 Frequency
Ex. “AM1 576”
If you make a mistake
Press C/c repeatedly until the character to
be changed flashes, then press X/x to select
the desired character.
To erase the character, press C/c
repeatedly until the character to be erased
flashes, then press CLEAR.
7
8
Press
.
“COMPLETE” appears in the front panel
display, and the station name is stored.
Press SYSTEM MENU.
The system menu turns off.
Viewing the station name or
frequency in the front panel
display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency
using the front panel display.
Press DISPLAY.
Each time you press DISPLAY, the display
changes:
1 t 2 t .... t 1 t ....
x “TUNER FM”
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
Ex. “FM1 87.50”
3 The “FM MODE” setting
Ex. “STEREO”
When the station name is not set
1 Frequency
Ex. “FM1 87.50”
2 The “FM MODE” setting
Ex. “STEREO”
x “TUNER AM”
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
Ex. “AM1 576”
GB
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the connected component, the Control
for HDMI function may not work. Refer to the
operating instructions supplied with the component.
• The Control for HDMI function may not work if you
connect a component other than a Sony component,
even if the component is compatible with the Control
for HDMI function.
Control for HDMI/External Audio
Device
Using the Control for
HDMI Function for
“BRAVIA” Sync
Preparing the Control for HDMI
function
This function is available on TVs with the
“BRAVIA” Sync function only.
(Control for HDMI - Easy Setting)
The system is compatible with the Control for
HDMI - Easy Setting function. If the TV is
compatible with the Control for HDMI - Easy
Setting function, you can set the system’s
[CONTROL FOR HDMI] function
By connecting Sony components that are
compatible with the Control for HDMI function
with an HDMI cable, operation is simplified as
below:
automatically by setting the TV. For details,
refer to the operating instructions of the TV.
If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control
for HDMI function of the system and TV
manually.
Control for HDMI is a mutual control function
standard used by CEC (Consumer Electronics
Control) for HDMI (High-Definition
Multimedia Interface).
1
2
3
Make sure that the system and the TV
are connected with an HDMI cable.
Turn on the TV and press [/1 to turn on
the system.
The Control for HDMI function will not work in
the following cases:
Switch the input selector on your TV so
that the signal from the system through
the HDMI input appears on the TV
screen.
– When you connect this system to a
component which is not compatible with the
Control for HDMI function.
– A component does not have an HDMI jack.
4
Set the Control for HDMI function of the
system and TV.
There are convenient buttons on the system’s
remote for operating the TV, such as
THEATER/THEATRE*, ONE-TOUCH
refer to the operating instructions of the TV.
* The button name differs depending on the area.
For details of the system settings, see the
following Steps. For details of the setting of
the TV, refer to the operating instructions of
the TV (depending on the TV, the default
setting of the Control for HDMI function
may be set to off).
To set the [CONTROL FOR HDMI]
function to on/off
ONE-TOUCH
PLAY
TV
THEATER
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
BRAVIA Sync
GB
70
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press
in stop mode.
DISPLAY while the system is
This system
TV
Turns on. (If not already Turns on. (If not already
turned on.)
The Control Menu display appears on the
TV screen.
turned on.)
r
r
Switches to “DVD”
function.
Switches to HDMI input.
3
4
5
Press X/x to select
then press
[SETUP],
r
.
r
Minimizes sound level.
(System Audio Control)
The options for [SETUP] appear.
Starts playing the disc and
outputs the sound.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
Press X/x to select [HDMI SETUP], then
Turning the system off in sync
with the TV
press
.
The options for [HDMI SETUP] appear.
6
7
Press X/x to select [CONTROL FOR
(System Power Off)
HDMI], then press
Press X/x to select the setting, then
press
.
When you turn the TV off by using the POWER
button on the TV’s remote or TV [/1 on the
system’s remote, the system turns off
automatically.
.
• [ON]: On.
• [OFF]: Off.
Note
• Before using the System Power Off function, set the
function for TV power. For details, refer to the
operating instructions of the TV.
Using the Theater/Theatre
Mode
• Depending on the status of the system (ex. while
using other than “DVD” or “TV/VIDEO” functions,
or playing a CD), the system may not turn off
automatically.
(Theater/Theatre Mode)
If your TV is compatible with the Theater/
Theatre Mode, you can enjoy optimal image and
sound quality suited for movies, and sound is
output from the system’s speakers automatically
by pressing THEATER/THEATRE*.
Enjoying TV sound from the
speakers by this system
* The button name differs depending on the area.
(System Audio Control)
You can enjoy TV sound via this system easily.
To use this function, connect the system and the
TV with an audio cord and an HDMI cable
Watching a DVD by a single
button press
(One-Touch Play)
Depending on the TV, when you set the system
to the “TV/VIDEO” function, the System Audio
Control function is activated. TV sound is output
from the system speakers, and the volume of the
TV speakers is minimized automatically.
By only pressing ONE-TOUCH PLAY, the TV
turns on, the TV is set for DVD input mode, and
the system starts playing a disc automatically.
Note
• One-Touch Play does not work when you press H.
You can use the System Audio Control function
as follows:
The system and TV work as follows (e.g.):
• While you are watching the TV and the
function of the system is switched to “TV/
GB
71
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO,” TV sound is output from the system
speakers automatically.
when the system’s on-screen display is
displayed, this function does not work.
• While you are watching the TV and the
function of the system is switched to “DVD,”
sound of the “DVD” function is output from
the system speakers; TV sound is not output
via the TV speakers.
• You can control the system’s volume by the
remote of the TV.
• If you turn the system off or set the function of
the system to other than “TV/VIDEO” or
“DVD,” TV sound is output from the TV
speakers.
You can also operate the System Audio Control
function via the TV menu. For details, refer to
the operating instructions of the TV.
Note
• While the TV is in PAP (picture and picture) mode,
the System Audio Control function will not work.
When the TV exits PAP mode, the output method of
the TV returns to the one before PAP mode.
Tip
• You can connect the system and the TV audio
Setting the Maximum Volume
Level of the System
(Volume Limit)
If you change the output method of the TV to the
system speakers via the TV menu (or by
pressing THEATER/THEATRE*), loud sound
may be output depending on the volume level of
the system. You can prevent this by limiting the
maximum level of the volume. For details, see
* The button name differs depending on the area.
Changing the language for the
on-screen display of the TV
(Language Follow)
When you change the language for the on-screen
display of the TV, the system’s on-screen
display language is also changed. However,
GB
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the type of DIGITAL MEDIA PORT
adapter, images are also output. In this case, the
system outputs the composite video signal only,
regardless of the type of video signal.
Using the DIGITAL MEDIA
PORT Adapter
The DIGITAL MEDIA PORT (DMPORT)
adapter is for enjoying sound from a portable
audio source or computer. By connecting a
DIGITAL MEDIA PORT adapter, you can
enjoy sound from the connected component on
the system.
Tip
• Depending on the type of DIGITAL MEDIA PORT
adapter, you may be able to operate a connected
component using either the buttons on the remote or
the unit. The following illustration shows an example
of buttons that can be used in this case.
Available DIGITAL MEDIA PORT adapters
vary in each area.
For details on connecting the DIGITAL MEDIA
Note
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is
turned on.
• When you use the system and the Bluetooth Wireless
Audio Adapter (such as TDM-BT1, not supplied) at
the same time, transmission distance between the
Bluetooth transmitter and Bluetooth Wireless Audio
Adapter may be reduced. In this case, place the
Bluetooth transmitter as far as possible from the
system, or move the Bluetooth Wireless Audio
Adapter closer to the Bluetooth transmitter.
• When you use the system and the Wireless Network
Audio Adapter (such as TDM-NC1, not supplied) at
the same time, place the Wireless Network Audio
Adapter as far as possible from the system.
./>
H
x
X
Playing the connected
component on the system
1
2
Press FUNCTION +/– repeatedly until
“DMPORT” appears in the front panel
display.
Start playback of the connected
component.
The sound and images from the connected
component are played on the system or
connected TV.
For operation details, refer to the operating
instructions of the DIGITAL MEDIA
PORT adapter.
GB
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• When you insert the wireless transmitter/transceiver,
make sure that the AC power cord (mains lead) is not
connected to a wall outlet (mains).
• Do not touch the terminals of the wireless transmitter/
transceiver.
Using an S-AIR Product
The unit is compatible with the S-AIR function
(page 103), which allows sound transmission
between S-AIR products.
When you purchase the S-AIR product, you
need to perform the following settings to
establish the sound transmission.
To insert the wireless transmitter
into the unit
1
Remove the screws and detach the slot
cover.
About S-AIR products
There are two types of S-AIR products.
• S-AIR main unit (this unit): This is for
transmitting sound. You can use up to three
S-AIR main units. (The number of usable
S-AIR main units depends on the use
environment.)
Rear of the unit
ANTENNA
EZW-T100
SPEAKER
FM
AM
COAXIAL 75
FRONT
R
FRONT
L
SUR
R
SUR
L
TV
DIGITAL IN
COMENT VIDEO OUT
VIDEO
OUT
TV/VIDEO
AUDIO IN
SPEAKER
HDMI OUT
DMPORT
DC5V
0.7A MAX
Y
B
P
R/CR
R
L
C
E
N
T
E
R
S
U
B
W
O
O
F
E
R
OPTICAL
COAXIAL
Slot cover
• S-AIR sub unit: This is for receiving sound.
0
0
1
-T
W
Z
E
– Surround amplifier: You can enjoy
surround speaker sound wirelessly.
– S-AIR receiver: You can enjoy system
sound in another room.
Room A
S-AIR main unit
Note
• Remove the screws from the slot cover bearing
the caution mark. Do not remove other screws.
• The slot cover is no longer necessary; however,
keep it after detaching.
2
Insert the wireless transmitter.
Rear of the unit
S-AIR sub unit
ANTENNA
(surround amplifier)
EZW-T100
SPEAKER
FM
COAXIAL 75
AM
FRONT
R
FRONT
L
SUR
R
SUR
L
TV
DIGITAL IN
COENT VIDEO OUT
VIDEO
OUT
TV/VIDEO
AUDIO IN
SPEAKER
HDMI OUT
DMPORT
DC5V
0.7A MAX
B
P
R/CR
R
L
C
E
N
T
E
R
S
U
B
W
O
O
F
E
R
OPTICAL
COAXIAL
Room B
-T100
EZW
S-AIR sub unit
(S-AIR receiver)
Inserting the wireless
transmitter/transceiver
Note
To make use of the S-AIR function, you need to
insert the wireless transmitter into the unit and
the wireless transceiver into the S-AIR sub unit.
• Insert the wireless transmitter with the S-AIR
logo facing up.
• Insert the wireless transmitter so that the V
marks are aligned.
GB
74
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not insert anything other than the wireless
transmitter into the EZW-T100 slot.
To set the ID of the unit
1
Press "/1 on the unit.
3
Make sure to use the same screws to
secure the wireless transmitter.
The system turns on.
2
3
Press SYSTEM MENU.
Rear of the unit
Press X/x repeatedly until “S-AIR ID”
appears in the front panel display, then
ANTENNA
EZW-T100
SPEAKER
FM
AM
COAXIAL 75
FRONT
R
FRONT
L
SUR
R
SUR
L
TV
DIGITAL IN
COENT VIDEO OUT
VIDEO
OUT
TV/VIDEO
AUDIO IN
SPEAKER
HDMI OUT
press
or c.
DMPORT
DC5V
B
P
R/CR
R
L
0.7A MAX
C
E
N
T
E
R
S
U
B
W
O
O
F
E
R
OPTICAL
COAXIAL
Note
• When the wireless transmitter is not inserted in
the unit, “S-AIR ID” cannot be selected.
-T100
EZW
4
5
6
7
Press X/x to select the desired ID.
You can select any ID (A, B, or C).
Press
.
The setting is made.
Press SYSTEM MENU.
Note
The system menu turns off.
• Do not use other screws to fasten the wireless
transmitter.
Set the S-AIR sub unit to the same ID.
Sound transmission is established as
follows (example):
To insert the wireless
transceiver into the S-AIR sub
unit
For details on installing the wireless transceiver
into the S-AIR sub unit, such as a surround
amplifier or S-AIR receiver, see the operating
instructions of the S-AIR sub unit.
S-AIR main unit
(This unit)
ID A
Tip
• When you change the S-AIR configuration, Sony
recommends that you perform [AUTO
CALIBRATION]. For details, see “Calibrating the
ID A
ID A
S-AIR sub unit
S-AIR sub unit
Establishing sound
transmission between the unit
and S-AIR sub unit
(ID setting)
Tip
• To confirm the current ID, perform Steps 1 to 3
above. When you pair the unit with the S-AIR sub
the front panel display.
For the surround amplifier
For the S-AIR receiver
To set the ID of the surround
amplifier
Refer to the operating instructions of the
surround amplifier.
Simply by matching the ID of the unit and the
S-AIR sub unit, you can establish sound
transmission.
GB
75
Download from Www.Somanuals.com. All Manuals Search And Download.
• “SEPARATE”: You can set the desired
function for the S-AIR receiver while unit
functions do not change.
To set the ID of the S-AIR
receiver
Refer to the operating instructions of the S-AIR
receiver.
4
5
6
Press
.
The setting is made.
To use multiple S-AIR main units
You can use multiple S-AIR main units by
setting a different ID for each component.
Press SYSTEM MENU.
The system menu turns off.
Select the desired function on the
S-AIR receiver.
S-AIR main unit
Other S-AIR
(This unit)
x When “PARTY” is set
main unit
The S-AIR receiver’s function changes
sequentially as you press FUNCTION +/–
the S-AIR receiver.
ID B
ID A
x When “SEPARATE” is set
The S-AIR receiver’s function changes
by pressing S-AIR CH of the S-AIR
receiver as follows.
ID A
S-AIR
sub unit
ID B
S-AIR sub unit
ID A
S-AIR sub unit
“MAIN UNIT” t “TUNER FM” t
“TUNER AM” t “DMPORT” t
“AUDIO” t …
To enjoy the same function as the unit,
select “MAIN UNIT.”
Enjoying the system’s sound in
another room
When “TUNER FM” or “TUNER AM” is
selected on the unit, you can only select the
same band for the tuner on the S-AIR
receiver. In this case, when you select other
than “TUNER FM” or “TUNER AM” on
the unit, you can select any band for the
tuner on the S-AIR receiver.
For the S-AIR receiver
You can enjoy the system’s sound by using the
S-AIR receiver. The S-AIR receiver can be
placed in another room for enjoying the
system’s sound there.
7
Adjust the volume on the S-AIR
receiver.
For details of the S-AIR receiver, refer to the
operating instructions of the S-AIR receiver.
Note
• When the sound is other than 2 channel stereo, multi-
channel sound is downmixed to 2 channel.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
MODE” appears in the front panel
display, then press
To set “S-AIR MODE” via the
remote
or c.
Note
Press S-AIR MODE.
• When the wireless transmitter is not inserted in
the unit, “S-AIR MODE” cannot be selected.
The S-AIR mode appears in the front panel
display. Each time you press S-AIR MODE, the
S-AIR mode changes.
3
Press X/x to select the desired setting.
• “PARTY”: The S-AIR receiver outputs
sound according to functions set on the
unit.
GB
76
Download from Www.Somanuals.com. All Manuals Search And Download.
To control the system from the
S-AIR receiver
You can control the system from the S-AIR
Note
• When you turn the system off while “S-AIR STBY”
is set to “STBY ON,” “S-AIR” flashes (when sound
transmission between the unit and S-AIR receiver is
not established), or lights up (when sound
transmission between the unit and S-AIR receiver is
established) in the front panel display.
receiver by using the following buttons.
Press
Operation
H, X, x,
./>
Share the same operations on the
remote and unit.
Identifying the unit with a
specific S-AIR sub unit
(Pairing operation)
S-AIR CH
Change the function of the system.
For details, refer to the operating instructions of
the S-AIR receiver.
For the surround amplifier
For the S-AIR receiver
Enjoying the S-AIR receiver
while the unit is in standby
mode
It is easy to set the same ID for the unit and an
S-AIR sub unit, such as a surround amplifier or
S-AIR receiver, to establish sound transmission.
However, neighbors may also receive your
system’s sound if IDs are the same, or you may
receive sound from neighbors. To prevent this,
you can identify the unit with a specific S-AIR
sub unit by performing the pairing operation.
For the S-AIR receiver
You can enjoy the S-AIR receiver while the unit
is in standby mode by setting “S-AIR STBY” to
“STBY ON.”
x Before pairing
Sound transmission is established by ID
(example).
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
STBY” appears in the front panel
Your room
This unit
Neighbor
display, then press
or c.
Note
• When the wireless transmitter is not inserted in
the unit, “S-AIR STBY” cannot be selected.
ID A
3
Press X/x to select the desired setting.
• “STBY ON”: You can enjoy the S-AIR
receiver while the unit is in standby mode
or turned on. The power consumption
during the standby mode increases.
• “STBY OFF”: You cannot enjoy the
S-AIR receiver while the unit is in
standby mode.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
The default setting differs depending on the
area.
4
5
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
GB
77
Download from Www.Somanuals.com. All Manuals Search And Download.
x After pairing
Sound transmission is established between the
paired unit and S-AIR sub unit(s) only.
6
Start pairing of the S-AIR sub unit.
x For the surround amplifier
Refer to the operating instructions of the
surround amplifier.
Your room
This unit
Neighbor
When sound transmission is established,
“PAIRING” and “COMPLETE” appear
alternately in the front panel display.
ID A
No transmission
x For the S-AIR receiver
Refer to the operating instructions of the
S-AIR receiver.
When sound transmission is established,
“PAIRING” and “COMPLETE” appear
alternately in the front panel display.
ID A
S-AIR sub unit
ID A
S-AIR sub unit
Note
• Perform pairing within several minutes of Step
5. If you do not, “PAIRING” and
“INCOMPLETE” appear alternately in the front
Pairing
panel display. To continue pairing, press
and
start again from Step 5. To cancel pairing, press
SYSTEM MENU.
To perform pairing
1
Place the S-AIR sub unit that you want
to pair near the unit.
7
Press SYSTEM MENU.
The system menu turns off.
Note
Note
• Remove headphones from the surround
amplifier (if connected).
• After you have performed pairing, if you select
“C”) that you last used is displayed first by default.
2
Match the IDs of the unit and the S-AIR
sub unit.
To cancel pairing
• To set the ID of the unit, see “To set the ID
Perform the ID setting of the unit according to
you select a new ID, pairing is canceled.
• To set the ID of the S-AIR sub unit, refer
to the operating instructions of the S-AIR
sub unit.
3
4
Press SYSTEM MENU.
If sound transmission is
unstable
Press X/x repeatedly until “PAIRING”
appears in the front panel display, then
press
or c.
For the surround amplifier
For the S-AIR receiver
Note
• When the wireless transmitter is not inserted in
the unit, “PAIRING” cannot be selected.
If you use multiple wireless systems which share
the 2.4 GHz band, such as wireless LAN or
Bluetooth, the transmission of S-AIR products
or other wireless systems may be unstable. In
this case, the transmission may be improved by
changing the following “RF CHANGE” setting.
5
After “START” appears in the front
panel display, press
.
The unit starts pairing and “SEARCH”
flashes in the front panel display.
To cancel pairing, press SYSTEM MENU.
1
Press SYSTEM MENU.
GB
78
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Press X/x repeatedly until “RF
CHANGE” appears in the front panel
display, then press
or c.
Press X/x to select the desired setting.
• “AUTO”: Normally select this. The
system changes “RF CHANGE” to “ON”
or “OFF” automatically.
• “ON”: The system transmits sound by
searching for the better channel for
transmitting.
• “OFF”: The system transmits sound by
fixing the channel for transmitting.
4
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
When you set “RF CHANGE” to “OFF,”
select the ID so that sound
transmission is most stable (page 75).
Note
• When the wireless transmitter is not inserted in the
unit, “RF CHANGE” cannot be selected.
• In most cases, you will not need to change this
setting.
– If “RF CHANGE” is set to “OFF,” transmission
between the unit and S-AIR sub unit can be
performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing the
transmission channel (frequency) of the other
wireless system(s). For details, refer to the operating
instructions of the other wireless system(s).
GB
79
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Press C/c to select a setting.
• [STANDARD]: Select this when you
install all the speakers normally.
• [NO CENTER]: Select this when you
install the front and surround speakers
only.
Other Operations
Getting Optimal
Surround Sound for a
Room
• [NO SURROUND]: Select this when you
install the center and front speakers only.
• [FRONT ONLY]: Select this when you
install the front speakers only.
• [ALL FRONT]: Select this when you
install all the speakers in front of the
listening position.
[SPEAKER FORMATION]
Depending on the shape of the room, you cannot
install some speakers. For better surround
sound, Sony recommends that first you decide
the position of the speakers.
• [ALL FRONT - NO CENTER]: Select
this when you install the front and
surround speakers in front of the listening
position.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
8
9
Press
.
2
Press
in stop mode.
DISPLAY while the system is
The setting is made and the confirmation
display appears.
The Control Menu display appears on the
TV screen.
Press C/c to select [YES] or [NO], then
press
.
3
4
5
6
Press X/x to select
then press
[SETUP],
• [YES]: Continue with [AUTO
CALIBRATION]. Follow the procedure
from Step 7 of “Calibrating the
.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
• [NO]: Exit [SPEAKER FORMATION].
The Setup Display appears.
Press X/x to select [AUDIO SETUP],
then press
.
The options for [AUDIO SETUP] appear.
Press X/x to select [SPEAKER
FORMATION], then press
.
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
STANDARD
GB
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibrating the
Appropriate Settings
Automatically
[AUTO CALIBRATION]
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
Note
• The system outputs a loud test sound when [AUTO
CALIBRATION] starts. You cannot turn the volume
down. Give consideration to children and neighbors.
Calibration mic
1
2
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
3
4
5
6
Press X/x to select
then press
[SETUP],
8
9
Press C/c to select [YES].
.
Press
.
The options for [SETUP] appear.
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
Press X/x to select [CUSTOM], then
press
.
Note
The Setup Display appears.
• Before [AUTO CALIBRATION], make sure
that the surround amplifier turns on and you
install the surround amplifier in the appropriate
location. If you install the surround amplifier in
an improper location, such as another room,
proper measurement will not be obtained.
• The environment of the room in which the
system is installed may affect measurements.
When the measurements differ considerably
from the status of the speaker installation,
perform the speaker settings manually by
Press X/x to select [AUDIO SETUP],
then press
.
The options for [AUDIO SETUP] appear.
Press X/x to select [AUTO
CALIBRATION], then press
.
The options for [AUTO CALIBRATION]
appear.
7
Connect the calibration mic (supplied)
to the A.CAL MIC jack on the front
panel.
10
Press C/c to select [YES] or [NO], then
Set up the calibration mic at ear level using
a tripod, etc. (not supplied).
press
.
x The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
When you want to cancel the measurement
and retry [AUTO CALIBRATION], select
[NO].
The front of each speaker should face the
calibration mic, and there should be no
obstruction between the speakers and the
calibration mic.
GB
81
Download from Www.Somanuals.com. All Manuals Search And Download.
x The measurement is not OK.
Follow the message, then select [YES] to
retry.
Controlling the TV with
the Supplied Remote
You can control the TV (Sony only) by using the
following buttons. Use these buttons (other than
TV [/1, THEATER/THEATRE*, TV INPUT,
and TV VOL +/–) while pressing the TV button.
* The button name differs depending on the area.
Note
• While the Auto Calibration function is working, do
not operate the system.
• The measurement for [SUBWOOFER] is always
[YES] since the system does not perform subwoofer
calibration, but the [SUBWOOFER] level in
[SPEAKER SETUP] returns to the default setting
when you perform [AUTO CALIBRATION].
Note
• Depending on the TV, you may not be able to control
your TV or to use some of the buttons.
By pressing
You can
TV [/1
Turn the TV on/off.
Enjoy optimal image quality
suited for movies.
THEATER/
THEATRE
TV INPUT
Switch the TV’s input source
between the TV and other input
sources.
TV VOL +/–
Adjust the TV volume.
Select the TV channel.
TV CH +/–*/
PROG +/–*
Number
Select the TV channel.
buttons*,
*,
-*, ENTER*
TOOLS*
Displays the operation menu for
the current display.
RETURN*
Return to the previous channel or
layer on the menu of the TV.
MENU*
Display the menu of the TV.
MUTING*
Turn off the TV sound
temporarily.
C/X/x/c*,
*
Select the item on the menu.
* Use these buttons while pressing the TV button.
GB
82
Download from Www.Somanuals.com. All Manuals Search And Download.
– “DEC. MODE” is set to “A.F.D. STD,”
“A.F.D. MULTI,” or “2CH STEREO”.
Using the Sound Effect
– Headphones are not connected.
When all the conditions above are satisfied, you
can activate/deactivate the effect by pressing
DMPORT BOOSTER on the unit. The
Reinforcing bass frequencies
You can reinforce bass frequencies.
DMPORT BOOSTER indicator turns on.
Press DYNAMIC BASS.
“D. BASS ON” appears in the front panel
display and bass frequencies are effectively
reinforced.
To turn off the sound effect
Press DMPORT BOOSTER on the unit so that
the DMPORT BOOSTER indicator turns off.
To turn off the sound effect
Press DYNAMIC BASS again.
Enjoying the sound at low
volume
You can enjoy sound effects or dialogue, as you
would in a movie theater, even at low volume. It
is useful for watching movies at night.
Press NIGHT.
“NIGHT ON” appears in the front panel display
and the sound effect is activated.
Note
• This effect does not work for a Super Audio CD.
When you load a Super Audio CD during “NIGHT
ON,” the sound effect turns off automatically.
• When sound is output from the center speaker, this
effect is more pronounced, as speech (movie dialog,
etc.) is easy to hear. When sound is not output from
the center speaker, or you are using the headphones,
the system optimally adjusts the volume.
To turn off the sound effect
Press NIGHT again.
Enhancing compressed sound
You can enhance compressed sound such as an
MP3 audio file.
This effect is activated automatically when all
the following conditions are satisfied:
– The function is set to “DMPORT” or
“AUDIO”.
GB
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Effect to
Suit the Source
You can select a suitable sound mode for movies
or music.
Enjoying Multiplex
Broadcast Sound
(DUAL MONO)
You can enjoy multiplex broadcast sound when
the system receives or plays a Dolby Digital
multiplex broadcast signal.
Press SOUND MODE repeatedly during
playback until the desired mode appears in
the front panel display.
Note
• “AUTO”: The system automatically selects
“MOVIE” (the MOVIE indicator lights up) or
“MUSIC” (the MUSIC indicator lights up) to
produce the sound effect depending on the
source.
• To receive a Dolby Digital signal, you need to
connect a TV or other component to the unit with an
digital output mode of the TV or other component to
Dolby Digital.
• “MOVIE”: The system provides the sound for
movies. The MOVIE indicator lights up.
• “MUSIC”: The system provides the sound for
music. The MUSIC indicator lights up.
Press AUDIO repeatedly until the desired
signal appears in the front panel display.
• “MAIN”: Sound of the main language will be
output.
• “SUB”: Sound of the sub language will be
output.
• “MAIN+SUB”: Mixed sound of both the main
and sub languages will be output.
Note
• When you play a Super Audio CD, this function does
not work.
• You cannot operate these setup items when you
connect headphones to the unit or surround amplifier.
• When changing the sound mode while using the
S-AIR receiver, sound from the S-AIR receiver may
skip.
GB
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Input Level Using the Sleep Timer
of the Sound from
Connected Components
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minute
increments.
Distortion may occur when you listen to a
Press SLEEP.
component connected to the TV/VIDEO jacks
on the rear panel, or to the AUDIO IN jack on
the front panel. Distortion is not a malfunction
and will depend on the component connected.
To prevent distortion, reduce the input level on
the unit.
Each time you press SLEEP, the minutes display
(the remaining time) changes by 10 minutes.
When you set the sleep timer, “SLEEP” flashes
in the front panel display.
To check the remaining time
1
Press FUNCTION +/– repeatedly until
“TV/VIDEO” or “AUDIO” appears in the
front panel display.
Press SLEEP once.
To change the remaining time
2
3
Press SYSTEM MENU.
Press SLEEP repeatedly to select the desired
time.
Press X/x repeatedly until
“ATTENUATE” appears in the front
panel display, then press
To cancel the sleep timer
function
or c.
4
Press X/x to select a setting.
Press SLEEP repeatedly until “SLEEP OFF”
appears in the front panel display.
• “ATT ON”: You can attenuate the input
level. The output level is changed.
• “ATT OFF”: Normal input level.
To set the sleep timer using the
system menu
5
6
Press
.
1
2
Press SYSTEM MENU.
The setting is made.
Press X/x repeatedly until “SLEEP”
appears in the front panel display, then
Press SYSTEM MENU.
The system menu turns off.
press
or c.
3
Press X/x to select a setting.
The minutes display (the remaining time)
changes by 10 minutes.
Tip
• You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
4
5
Press
.
The setting is made and “SLEEP” flashes in
the front panel display.
Press SYSTEM MENU.
The system menu turns off.
GB
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Brightness Viewing Information
of the Front Panel
About the Disc
Display
You can set the brightness of the front panel
display to either of 2 levels.
Viewing the playing time and
remaining time in the front
panel display
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press
or c.
Press DISPLAY repeatedly.
3
Press X/x to select the brightness of
the front panel display.
Each time you press DISPLAY while playing
the disc, the display changes:
1 t 2 t ... t 1 t ...
Some displayed items may disappear after a few
seconds.
• “DIMMER OFF”: The front panel display
is bright.
• “DIMMER ON”: The front panel display
is dark.
x DVD VIDEO/DVD-VR
4
5
Press
.
1 Playing time of the current title
2 Remaining time of the current title
3 Playing time of the current chapter
4 Remaining time of the current chapter
5 Disc name
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
6 Title and chapter
x VIDEO CD (without PBC functions)/
Super Audio CD/CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Track name
6 Track and index*
* VIDEO CD/Super Audio CD only.
x Super VCD
1 Playing time of the current track
2 Track text
3 Track and index number
x DATA CD (MP3 file)/DATA DVD (MP3 file)
1 Playing time and current track number
2 Track (file) name*
* If an MP3 file has an ID3 tag, the system will
display an album name or title name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
GB
86
Download from Www.Somanuals.com. All Manuals Search And Download.
x DATA CD (video file)/DATA DVD (video
file) (Except for North American models)
1 Playing time of the current file
2 Current file name
x VIDEO CD (with PBC functions)
• **:**
Playing time of the current scene
x VIDEO CD (without PBC functions)/
Super Audio CD/CD
3 Current album and file number
• T **:**
Note
• The system can only display the first level of the
DVD/CD text, such as the disc name or title.
• If a file name of the MP3 file cannot be displayed, “*”
will appear in the front panel display instead.
• The disc name or track name may not be displayed
depending on the text.
Playing time of the current track
• T-**:**
Remaining time of the current track
• D **:**
Playing time of the current disc
• D-**:**
• Playing time of MP3 files and video files* may not be
displayed correctly.
Remaining time of the current disc
* Except for North American models.
x DATA CD (MP3 file)/DATA DVD (MP3
file)
Tip
• T **:**
Playing time of the current track
• When the system is playing a VIDEO CD with PBC
functions, the playing time is displayed.
x DATA CD (video file)/DATA DVD
(video file) (Except for North American
models)
Viewing the playing time and
remaining time on the TV
screen
• **:**:**
Playing time of the current file
Note
• Characters/marks may not be displayed in some
languages.
1
Press DISPLAY during playback.
The following display appears on the TV
screen.
• Depending on the type of disc being played, the
system can only display a limited number of
characters. Also, depending on the disc, not all text
characters will be displayed.
T
1: 01: 40
Time information
Checking the play information
of the disc
2
Press DISPLAY repeatedly to change
the time information.
The display and the kinds of time that you
can check depend on the disc you are
playing.
To check DVD/Super Audio CD/CD
text
Press DISPLAY repeatedly during playback to
display text recorded in the DVD/Super Audio
CD/CD.
The DVD/Super Audio CD/CD text appears
only when text is recorded in the disc. You
cannot change the text. If the disc does not
contain text, “NO TEXT” appears.
x DVD VIDEO/DVD-VR
• T **:**:**
Playing time of the current title
• T-**:**:**
Remaining time of the current title
• C **:**:**
Playing time of the current chapter
• C-**:**:**
Remaining time of the current chapter
Dvorak/Tchaikovsky /NedPho/Kreizberg
Adagio - Allegro molto
GB
87
Download from Www.Somanuals.com. All Manuals Search And Download.
To check DATA CD/DATA DVD
(MP3 file/video file ) text
5(
8)
1)
10( 15)
DATA CD
9/18/2002
By pressing DISPLAY while playing MP3 files
1)
or video files on a DATA CD/DATA DVD,
Date information
you can display the name of the folder/MP3 file/
1)
video file , and the audio bit rate (the amount of
data per second of the current audio) on the TV
screen.
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
Example for playback of an audio file
Bit rate2)
T
0: 13 192k MP3
2002_Remixes
Soul_Survivor_rap_version
Folder name3)
MP3 file3)/video file1) name
1)Except for North American models.
2)Appears when playing an MP3 file on a DATA CD/
DATA DVD.
3)If an MP3 file has the ID3 tag, the system will display
an album name or title name from the ID3 tag
information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
Checking the date information
of a JPEG image file
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image file.
Press
DISPLAY during playback.
The Control Menu display appears on the TV
screen.
GB
88
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select [SYSTEM SETUP],
then press
.
Returning to the Default
Settings
The options for [SYSTEM SETUP] appear.
6
7
Press X/x to select [RESET] and press
c.
Press C/c to select [YES].
Returning the system
parameters, such as preset
stations, to the default
settings
You can also quit the process and return to
the Control Menu display by selecting [NO]
here.
8
Press
.
Do not press [/1while resetting the system
as it takes a few seconds to complete.
N
x
"/1
Note
• The [MEDIA], [INTERVAL], [EFFECT], and
[MULTI/2CH] settings also return to the default
settings.
1
2
Press "/1 to turn on the system.
Press x, N, and "/1 on the unit at the
same time.
“COLD RESET” appears in the front panel
display and the system returns to default
settings.
Returning the [SETUP] settings
to the default
You can return the [SETUP] settings (page 59)
other than [PARENTAL CONTROL] to the
default settings.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
3
4
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
GB
89
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
Additional Information
Precautions
On power sources
• Unplug the unit from the wall outlet (mains) if you do
not intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
On cleaning
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On placement
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the system in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the system can overheat and malfunction.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
• Do not place the system on surfaces (rugs, blankets,
etc.) or near materials (curtains, draperies) that may
block the ventilation slots.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
• Do not install the system near heat sources such as
radiators, or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
• Do not install the system in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the system and discs away from components
with strong magnets, such as microwave ovens, or
large loudspeakers.
On moving the system
• Do not place heavy objects on the system.
1
2
3
Press FUNCTION +/– repeatedly to
select “DVD.”
On operation
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the unit. Should
this occur, the system may not operate properly. In
this case, remove the disc and leave the system turned
on for about half an hour until the moisture
evaporates.
Make sure that all discs are removed
from the unit.
Press H and "/1 simultaneously.
“MECHA LOCK” and “UNPLUG”
appear alternately in the front panel
display.
• When you move the system, take out any disc. If you
don’t, the disc may be damaged.
4
Remove the AC power cord (mains
lead) from the wall outlet (mains).
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
GB
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
This system can only play back a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
GB
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your
nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
When you install the S-AIR sub unit (optional), in the event of a problem with the S-AIR function, have
a Sony dealer check the entire system together (main unit and S-AIR sub unit).
Power
Symptom
Remedy
The power is not turned on.
• Check that the AC power cord (mains lead) is connected securely.
• Press "/1 after “STANDBY” disappears from the front panel display.
If “PROTECTOR” and “PUSH Press "/1 to turn off the system, and check the following items after
POWER” appear alternately in “STANDBY” disappears.
the front panel display.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If
the cause of the problem cannot be found even after checking all the above
items, consult your nearest Sony dealer.
GB
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Symptom
Remedy
There is no picture.
• The video connecting cords are not connected securely.
• The video connecting cords are damaged.
• The video input on the TV is not set so that you can view pictures from the
system.
• You have set progressive format but your TV cannot accept the signal in
progressive format. In this case, return the setting to interlace format (the
• Even if your TV is compatible with progressive format (525p/625p) signals, the
image may be affected when you set progressive format. In this case, return the
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
• If the HDMI OUT jack is used for video output, change the type of video signal
Connect the TV and the unit using a video jack other than the HDMI OUT, and
switch the TV’s input to the connected video input so that you can see the on-
screen displays. Change the type of video signal output from the HDMI OUT
jack, and switch the TV’s input back to HDMI. If the picture still does not
appear, repeat the Steps and try other options.
• You have set [PROGRESSIVE (COMPONENT OUT)] in [VIDEO SETUP] to
this case, disconnect the HDMI cable from the unit and then set it to [OFF].
• If you are using the “DMPORT” function, the video signal is output from the
VIDEO OUT jack only.
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your system goes through your VCR to get to your
TV, the copy-protection signal applied to some DVD programs could affect
picture quality. If you experience problems when you connect your unit through
Even though you set the aspect • The aspect ratio on the disc is fixed.
ratio in [TV TYPE] of [VIDEO
SETUP], the picture does not fill
the TV screen.
Color irregularity occurs on the The system’s speakers contain magnet parts, so magnetic distortion may occur.
TV screen.
When color irregularity occurs on the TV screen, check the following items.
• If the speakers are used with a CRT-based TV or projector, install the speakers
at least 0.3 meters (1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15
to 30 minutes.
• If howling occurs, reposition the speakers farther away from the TV set.
• Make sure that no magnetic object (magnetic latch on a TV stand, health care
device, toy, etc.) is placed near the speakers.
GB
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound
Symptom
Remedy
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON” is displayed in the front panel
display.
• The system is in pause mode or in Slow-motion Play mode. Press H to return
to normal play mode.
• Fast forward or fast reverse is being performed. Press H to return to normal
play mode.
• Super Audio CD audio signals are not output from the HDMI OUT jack.
• The component connected to the HDMI OUT jack does not conform to the
audio signal format, in this case set [AUDIO (HDMI)] in [HDMI SETUP] to
No sound is output from the
HDMI OUT jack.
• The HDMI OUT jack is connected to a DVI (Digital Visual Interface) device
(DVI (Digital Visual Interface) jacks do not accept audio signals).
• The HDMI OUT jack does not output Super Audio CD sound.
• Try the following: 1 Turn the system off and on again. 2 Turn the connected
component off and on again. 3 Disconnect and then connect the HDMI cable
again.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components are connected correctly and securely.
There is no sound from the
subwoofer.
Severe hum or noise is heard.
• Check that the speakers and components are connected securely.
• Check that the connecting cords are away from a transformer or motor, and at
least 3 meters (10 ft) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The sound loses stereo effect
when you play a VIDEO CD, a
CD, or an MP3 file.
• Make sure the unit is connected properly.
hear when you are playing a
sound track of Dolby Digital,
DTS, or MPEG audio.
• Depending on the DVD, the output signal may not be the entire 5.1 channel. It
may be monaural or stereo even if the sound track is recorded in Dolby Digital
or MPEG audio format.
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.
speaker only.
No sound is heard from the
center speaker.
• Depending on the source, the effect of the center speaker may be less
noticeable.
• A 2 channel source is being played.
GB
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
No sound or only a very low-
level sound is heard from the
surround speakers.
• Depending on the source, the effect of the surround speakers may be less
noticeable.
• A 2 channel source is being played.
There is no sound from the
DIGITAL IN COAXIAL/
OPTICAL jack.
• The sampling frequency of the input stream is more than 48 kHz.
Noise is heard on AM radio.
Operation
Symptom
Remedy
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna
in.
(aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic
tuning). Use direct tuning.
• No stations have been preset or the preset stations have been cleared (when
The remote does not function.
The disc does not play.
• There are obstacles between the remote and the unit.
• The distance between the remote and the unit is too far.
• The remote is not pointed at the remote sensor on the unit.
• The batteries in the remote are weak.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 7).
• The region code on the DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
The MP3 file cannot be played. • The DATA CD is not recorded in ISO 9660 Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in UDF (Universal Disk Format).
• The MP3 file does not have the extension “.mp3.”
• The data is not formatted in MP3 even though it has the extension “.mp3.”
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO format.
The JPEG image file cannot be • The DATA CD is not recorded in ISO 9660 Level 1/Level 2, or Joliet.
played.
• The DATA DVD is not recorded in UDF (Universal Disk Format).
• It has an extension other than “.jpeg” or “.jpg.”
• It is larger than 3,072 (width) × 2,048 (height) in normal mode, or more than
2,000,000 pixels in progressive JPEG image file which is mainly used on
Internet Web sites.
• It does not fit the TV screen (those images are reduced).
GB
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The video file cannot be played • The file is not created in DivX format or MP4 file format.
(except for North American
models).
• The file has an extension other than “.avi,” “.divx,” “.mp4,” or “.m4v.”
• The DATA CD/DATA DVD is not created in ISO 9660 Level 1/Level 2, or
Joliet/UDF.
• The video file is larger than 720 (width) × 576 (height).
The titles of folder/file/file name • The system can only display numbers and letters of the alphabet. Other
are not displayed correctly.
characters are displayed as [*].
A disc does not start playing
from the beginning.
• Program Play, Shuffle Play, or Repeat Play has been selected.
Press CLEAR to cancel these functions before playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and then start playback
• The title, DVD or PBC menu automatically appears on the TV screen.
The system starts playing the
disc automatically.
• The DVD features an auto playback function.
Playback stops automatically.
• Some discs may contain an auto pause signal. While playing such a disc, the
system stops playback at the auto pause signal.
You cannot perform some
functions such as stop, search,
Slow-motion Play, or Repeat
Play.
• Depending on the disc, you may not be able to perform some of these
operations. Refer to the operating instructions supplied with the disc.
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in
TV screen in the language you
want.
The language for the sound track • Multilingual tracks are not recorded on the DVD being played.
cannot be changed.
• The DVD prohibits changing the language for the sound track.
The subtitle language cannot be • Multilingual subtitles are not recorded on the DVD being played.
changed.
• The DVD prohibits changing the subtitles.
The subtitle cannot be turned off. • The DVD prohibits turning off subtitles.
• The DVD prohibits changing the angles.
A disc cannot be ejected and
“LOCKED” appears in the front
panel display.
• Contact your Sony dealer or local authorized Sony service facility.
[Data error] appears on the TV • The MP3 file/JPEG image file/video file* you want to play is broken.
screen when playing a DATA
CD or DATA DVD.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to DCF.
• The file has the extension “.jpg” or “.jpeg,” but is not in JPEG format.
• The file you want to play has the extension “.avi” or “.divx” but is not in DivX
format, or is in DivX format but does not conform to DivX Certified profiles.*
• The file you want to play has the extension “.mp4” or “.m4v” but is not in MP4
format, or is in MP4 format but does not conform to MPEG4 Simple Profiles.*
* Except for North American models.
The system does not work
normally.
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then
reconnect after several minutes.
GB
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The Control for HDMI function • When “HDMI” does not light up in the front panel display, check the HDMI
does not work.
• Set [CONTROL FOR HDMI] in [HDMI SETUP] to [ON] (page 62).
• Make sure that the connected component is compatible with the [CONTROL
FOR HDMI] function.
• Check that the AC power cord (mains lead) of the connected component is
connected securely.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power
cord (mains lead), or have a power failure, set [CONTROL FOR HDMI] in
[HDMI SETUP] to [OFF], then set [CONTROL FOR HDMI] in [HDMI
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
No sound is output from the
system and TV while using the
System Audio Control function.
• Make sure that the connected TV is compatible with the System Audio Control
function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
The S-AIR function
Symptom
Remedy
S-AIR connection is not
established (sound transmission
is not established), e.g., the
indicator of the S-AIR sub unit
does the following:
• Turns off.
• If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away
from the S-AIR main unit you are using.
• Another S-AIR sub unit is paired to the S-AIR main unit. Pair the desired S-AIR
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other
wireless devices.
• Flashes.
• Turns red.
• Avoid using any other wireless devices.
• The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is
connected and turn on the S-AIR sub unit.
No sound is heard from the
S-AIR sub unit.
• If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away
from the S-AIR main unit you are using.
• Place so that the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other
wireless devices.
• Avoid using any other wireless devices.
• Change the “RF CHANGE” setting (page 78).
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then turn on them.
GB
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away
from the S-AIR main unit you are using.
• Place so that the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other
wireless devices.
• Avoid using any other wireless devices.
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.
GB
98
Download from Www.Somanuals.com. All Manuals Search And Download.
When the version number
appears on the TV screen
Self-diagnosis Function
(When letters/numbers appear in the
display)
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the TV screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case,
check the following table.
VER.X.XX
C:13:50
First 3
Cause and/or corrective action
characters of
the service
number
C 13
The disc is dirty.
,Clean the disc with a soft cloth
C 31
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
E XX
To prevent a malfunction, the
system has performed the self-
diagnosis function.
(XX is a
number)
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
Example: E 61 10
GB
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Audio CD/DVD System
Laser Diode Properties Emission Duration:
Specifications
AUDIO POWER SPECIFICATIONS
for the U.S. model
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
Continuous
Laser Output: Less than
44.6μW
* This output is the value measurement at a distance
of 200mm from the objective lens surface on the
Optical Pick-up Block with 7mm aperture.
Signal format system
With 3 ohms loads, both
channels driven, from 180
- 20,000 Hz; rated 84 watts
per channel minimum
North American models: NTSC
Other models:
PAL/NTSC
Tuner Section
System
RMS power, with no more
than 0.7% total harmonic
distortion from 250 milli
watts to rated output.
PLL quartz-locked digital
synthesizer
FM tuner section
Tuning range
Amplifier Section
U.S. models:
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:144watts
(per channel at 3 ohms, 1
kHz, 10% THD)
North American models: 87.5 MHz - 108.0 MHz
(100 kHz step)
Other models:
87.5 MHz - 108.0 MHz (50
kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Subwoofer*: 280 watts (at
1.5 ohms, 80 Hz, 10%
THD)
Intermediate frequency
AM tuner section
Tuning range
10.7 MHz
Other models:
Stereo mode (rated)
North American, Mexican, and Latin American
models:
108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:144watts
(per channel at 3 ohms, 1
kHz, 10% THD)
Subwoofer*: 280 watts (at
1.5 ohms, 80 Hz, 10%
THD)
European, CIS, and Middle Eastern models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
Australian and New Zealand models:
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
*
Depending on the decoding mode settings and the
source, there may be no sound output.
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
Inputs (Analog)
TV/VIDEO (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN
Inputs (Digital)
TV/VIDEO (COAXIAL IN/OPTICAL IN)
Impedance: 75 ohms/-
Other models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
530 kHz - 1,610 kHz (with
the interval set at 10 kHz)
AM loop antenna (aerial)
450 kHz
Sensitivity: 250/125 mV
Antenna (aerial)
Intermediate frequency
Input Stream: Dolby
Digital 5.1ch/DTS 5.1ch/
Linear PCM 2ch
(Sampling Frequency: less
than 48 kHz)
Video Section
Outputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
Outputs (Analog)
Phones
Accepts low- and high-
impedance headphones.
HDMI OUT: Type A (19
pin)
GB
100
Download from Www.Somanuals.com. All Manuals Search And Download.
3 1/2 in) speaker only for
reference) (w/h/d)
2.3 kg (5 lb 2 oz)
Speakers
Front
Mass (approx.)
DAV-HDX285 (SS-TS94)
Subwoofer (SS-WS95)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
Subwoofer Bass reflex
160 mm (6 3/8 in) cone type
1.5 ohms
103 mm × 225 mm × 91
mm (4 1/8 in × 8 7/8 in ×
3 5/8 in) (w/h/d)
225 mm × 395 mm × 325
mm (8 7/8 in × 15 5/8 in ×
12 7/8 in) (w/h/d)
Mass (approx.)
0.7 kg (1 lb 9 oz)
Mass (approx.)
6.5 kg (14 lb 6 oz)
DAV-HDX585/DAV-HDX685 (SS-TS95)
General
Power requirements
North American models: 120 V AC, 60 Hz
Other models:
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
255 mm × 910 / 940 / 970 /
1000 mm × 255 mm (10 1/8
in × 35 7/8 / 37 1/8 / 38 1/4 /
39 3/8 in × 10 1/8 in)
220 V - 240 V AC,
50/60 Hz
On: 160 W
Standby: 0.3 W (at the
Power Saving mode)
Power consumption
(103 mm × 545 mm × 86
mm (4 1/8 in × 21 1/2 in ×
3 1/2 in) speaker only for
reference) (w/h/d)
Output voltage (DIGITAL MEDIA PORT)
DC 5 V
Output current (DIGITAL MEDIA PORT)
700 mA
Mass (approx.)
2.3 kg (5 lb 2 oz)
Dimensions (approx.)
430 mm × 85 mm × 415
mm (17 in × 3 3/8 in ×
16 3/8 in) (w/h/d) incl.
projecting parts
Center (SS-CT91)
Speaker system
Full range Bass reflex,
Magnetically Shielded
65 mm (2 5/8 in) cone type
3 ohms
265 mm × 94 mm × 77 mm
(10 1/2 in × 3 3/4 in × 3 1/8 in)
(w/h/d)
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
5.2 kg (11 lb 8 oz)
Supported file format
MP3 (MPEG 1 Audio Layer-3)
File Extension:
mp3
Bitrate:
Sampling frequencies:
32 kbps - 320 kbps
32/44.1/48 kHz
Mass (approx.)
0.7 kg (1 lb 9 oz)
Surround
DivX (Except for North American models)
DAV-HDX285/DAV-HDX585 (SS-TS92)
File Extension:
Video codec:
Bitrate:
Frame rate:
Resolution:
Audio codec:
avi/divx
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
DivX video
8 Mbps (MAX)
30 fps
103 mm × 164 mm × 94
mm (4 1/8 in × 6 1/2 in ×
3 3/4 in) (w/h/d)
720 × 576
MP3
MPEG4 (Except for North American
models)
Mass (approx.)
0.5 kg (1 lb 2 oz)
DAV-HDX685 (SS-TS95)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
File format:
MP4 File Format
Full range Bass reflex
65 mm (2 5/8 in) cone type
3 ohms
255 mm × 910 / 940 / 970 /
1000 mm × 255 mm (10 1/8
in × 35 7/8 / 37 1/8 / 38 1/4 /
39 3/8 in × 10 1/8 in)
(103 mm × 545 mm × 86
mm (4 1/8 in × 21 1/2 in ×
File Extension:
Video codec:
mp4/m4v
MPEG4 Simple Profile
(AVC is not compatible.)
4 Mbps
Bitrate:
Frame rate:
Resolution:
Audio codec:
30 fps
720 × 576
AAC-LC (HE-AAC is not
compatible.)
DRM:
Not compatible
GB
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Design and specifications are subject to change
without notice.
Glossary
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjust the
speaker settings to your listening environment in
a short period of time.
Digital Direct Twin Drive Subwoofer
Utilizing Sony proprietary S-master technology,
the Digital Direct Twin Drive Subwoofer
features two S-master Digital Amplifiers that
provide dedicated power to a strategically
located subwoofer for astounding sound
performance. Easy to set up, Digital Direct Twin
Drive Subwoofer provides a stable sound field
over a much larger listening area without having
to adjust frequency levels.
Dolby Digital
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
GB
102
Download from Www.Somanuals.com. All Manuals Search And Download.
x Music mode
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
Progressive format
Dolby Surround Pro Logic
(sequential scanning)
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
In contrast to the interlace format, the
progressive format can reproduce 50 - 60 frames
per second by reproducing all scanning lines
(525 lines for the NTSC system). The overall
picture quality increases and still images, text
and horizontal lines appear sharper. This format
is compatible with the 525 or 625 progressive
format.
S-AIR
(Sony Audio Interactive Radio
frequency)
DTS
Recent times have seen the rapid spread of DVD
media, Digital Broadcasting, and other high-
quality media.
To ensure that the subtle nuances of these high-
quality media are transmitted with no
deterioration, Sony has developed a technology
called “S-AIR” for the radio transmission of
digital audio signals with no compression, and
has incorporated this technology into the EZW-
RT10/EZW-RT10A/EZW-T100.
This technology transfers digital audio signals
with no compression using the 2.4 GHz band
range of ISM band (Industrial, Scientific, and
Medical band), also used by wireless LANs and
Bluetooth applications.
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
is comprised of a stereo rear channel and a
discrete subwoofer channel. DTS provides the
same 5.1 discrete channels of high quality digital
audio. The good channel separation is realized
due to the all channel data being recorded
discretely and processed digitally.
HDMI (High-Definition Multimedia
Interface)
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Content Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
Super Audio CD
Super Audio CD is a new high-quality audio
disc standard where music is recorded in the
DSD (Direct Stream Digital) format
(conventional CD is recorded in the PCM
format). The DSD format, using a sampling
frequency 64 times higher than that of a
conventional CD, and with 1-bit quantization,
achieves both a wide frequency range and a wide
dynamic range across the audible frequency
range, and so provides music reproduction
extremely faithful to the original sound.
Interlace format
(Interlaced scanning)
The interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice -
alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
x Super Audio CD types
Parental Control
There are two types of discs, depending on the
Super Audio CD layer and CD layer
combination.
A function of the DVD to limit playback of the
disc by the age of users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
GB
103
Download from Www.Somanuals.com. All Manuals Search And Download.
• Super Audio CD layer: A high-density
signal layer for Super Audio CD
• CD layer1): A layer that is readable by a
conventional CD player
Single layer disc
(a disc with a single Super Audio CD layer)
Super Audio CD
layer
Hybrid disc2)
(a disc with a Super Audio CD layer and a CD layer)
CD layer3)
Super Audio CD
layer3)
A Super Audio CD layer consists of the 2
channel area or the multi-channel area.
• 2 channel area: An area in which 2 channel
stereo tracks are recorded
• Multi-channel area: An area in which multi-
channel (up to 5.1 channels) tracks are
recorded
2 channel area4)
Multi-channel area4)
Super Audio CD
layer
1)You can play the CD layer on a conventional CD
player.
2)Since both layers are on one side, it is not necessary
to turn the disc over.
GB
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback priority of file types
The table below describes the playback priority of file types under the [MEDIA] setting.
File type
[MEDIA] setting
[VIDEO]*
[MUSIC/PHOTO]
[PHOTO]
[MUSIC]
Video files only*
JPEG image files only
MP3 files only
Video files*
JPEG image files
MP3 files
Video files*
Video files*
JPEG image files
MP3 files
Video files*
JPEG image files
MP3 files
JPEG image files
MP3 files
Video files* and JPEG
image files
Video files*
JPEG image files
JPEG image files
Video files*
Video files* and MP3 files Video files*
MP3 files
MP3 files
MP3 files
MP3 files
MP3 files and JPEG image MP3 files and JPEG MP3 files and JPEG JPEG image files
files
image files with
slide show
image files with
slide show
Video files*, MP3 files, and Video files*
JPEG image files
MP3 files and JPEG JPEG image files
image files with
MP3 files
slide show
* Except for North American models.
GB
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
GB
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
Front panel
D
(remote sensor) (13)
GB
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
Screws*
ANTENNA
EZW-T100
SPEAKER
FM
COAXIAL 75
AM
FRONT
R
FRONT
L
SUR
R
SUR
L
TV
DIGITAL IN
COMPONENT VIDEO OUT
TV/VIDEO
AUDIO IN
VIDEO
OUT
SPEAKER
HDMI OUT
DMPORT
DC5V
0.7A MAX
Y
P
B/CB
PR/CR
R
L
CENTER SUBWOOFER
OPTICAL
COAXIAL
H DMPORT (DIGITAL MEDIA PORT) jack
J TV/VIDEO (DIGITAL IN COAXIAL/
OPTICAL) jacks (28)
*
CAUTION
Please do not remove the screws unless you
are installing the EZW-T100.
GB
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
About the indications in the front panel display
A Playing status
G Lights up when the HDMI OUT jack is
correctly connected to HDCP (High-
bandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input. (26)
B Flashes when the sleep timer is set.
C Displays the system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, decoding mode, etc.
H Current surround format (Except for
JPEG image file)
I Lights up when the color system is set
to NTSC. (Asian, Australian, and Middle
Eastern models only)
D Lights up when a station is received.
(Radio only) (67)
E Stereo/Monaural effect (Radio only)
J Lights up when a Super Audio CD/CD
is loaded. (44)
F Lights up when the S-AIR transmitter
(not supplied) is inserted in the unit
and the system transmits the sound.
GB
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A – O
P – Z
1)
S-AIR MODE 4
C/X/x/c/
REPLAY/ADVANCE
2)
STEP
/
SLOW
/
3)
4)
1)
3)
1)Except for North American
models.
2)The button name differs
depending on the area.
3)North American models
only.
4)This button is available for
the “DVD” or “DMPORT”
function. Depending on the
DIGITAL MEDIA PORT
adapter, this button may not
work.
GB
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
You can use the Control Menu display to select a function and to view related information.
DISPLAY
Press
DISPLAY repeatedly.
DISPLAY, the Control Menu display changes:
Each time you press
1 t 2 t ... t 1 t ...
1 Control Menu display 1
2 Control Menu display 2 (appears when available)
3 Control Menu display off
Note
• The Control Menu Display appears during the “DVD” function.
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For details,
see the pages in parentheses.
GB
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing title number
Currently playing chapter number
Total number of titles
Playback status
(N Playback,
Total number of chapters
Control Menu items
X Pause,
x Stop, etc.)
98( 99)
13( 99)
Type of disc being
played
DVD VIDEO
T
0: 04: 17
Selected item
OFF
OFF
Playing time
ALL DISCS
ONE DISC
TITLE
Current setting
CHAPTER
Options
Function name of selected
Control Menu item
REPEAT
ENTER
DISPLAY
Quit:
Operation message
To turn off the display
Press
DISPLAY.
List of Control Menu items
Item
Item Name, Function, Relevant Disc Type
You can select the title, scene, or track to be played.
You can select the chapter or index to be played.
[INDEX] (page 49)
You can display the index and select the index to be played.
[TRACK] (page 49)
You can select the track to be played.
[ORIGINAL/PLAY LIST] (page 49)
You can select the type of titles (DVD-RW/DVD-R) to be played, the [ORIGINAL] one, or
an edited [PLAY LIST].
[TIME] (page 49)
You can check the elapsed time and the remaining playback time.
You can play from a desired point by inputting the time code (DVD VIDEO/DVD-VR only).
[MULTI/2CH] (page 44)
You can select the playback area on a Super Audio CD when available.
[SUPER AUDIO CD/CD LAYER] (page 44)
You can select the playback layer on a Super Audio CD when available.
[PROGRAM] (page 46)
You can select the track to play in the order you want.
GB
112
Download from Www.Somanuals.com. All Manuals Search And Download.
[SHUFFLE] (page 47)
You can play the tracks/files in random order.
[REPEAT] (page 47)
You can play all discs repeatedly, the entire disc (all titles/all tracks/all folders/all files)
repeatedly, or one title/chapter/track/folder/file repeatedly.
[A/V SYNC] (page 56)
You can adjust the delay between the picture and sound.
1)
1)
[DISC MENU] (page 48)
You can display the DVD’s menu.
[BROWSING] (page 54)
You can display the list of folders/JPEG image files.
[SETUP] (page 59)
[QUICK] (page 33)
You can make the basic adjustments. Use Quick Setup to select the desired language of the
on-screen display, the aspect ratio of the TV, and select yes or no to start the Auto Calibration.
[CUSTOM]
In addition to the Quick Setup setting, you can adjust various other settings.
[FOLDER] (page 49)
You can select the folder to be played.
[FILE] (page 49)
You can select the JPEG image file or video file to be played.
1)
2)
2)
[DATE] (page 88)
You can display the date the picture was taken by a digital camera.
[INTERVAL] (page 53)
You can select the duration for which the slides are displayed on the TV screen.
2)
[EFFECT] (page 53)
You can select the effects to be used for changing slides during a slide show.
[MEDIA] (page 53)
:
1)
You can select the data type (MP3 file, JPEG image file, video file , or both MP3 file and
North
JPEG image file) to be played on a DATA CD/DATA DVD.
American
models
:
Other
models
1)Except for North American models.
2)These items are not displayed when playing a DATA CD/DATA DVD with video files (except for North American
models).
Tip
• The Control Menu icon indicator lights up in yellow
t
when you select any item except [OFF]
([PROGRAM], [SHUFFLE], [REPEAT], and [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights
up in yellow when you select [PLAY LIST] (default setting). The [MULTI/2CH] indicator lights up in yellow when
you select the multi-channel playback area on a Super Audio CD.
GB
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
E
P
PROGRESSIVE
F
A
H
HDMI
HDMI (High-Definition
Q
B
R
I
BLACK LEVEL
RF POWER 79
C
J
COLOR SYSTEM (VIDEO
S
L
D
M
Digital Direct Twin Drive
DivX® 54, 64
N
O
GB
114
Download from Www.Somanuals.com. All Manuals Search And Download.
T
V
GB
115
Download from Www.Somanuals.com. All Manuals Search And Download.
(1)
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|