3-283-040-11(1)
DVD Home Theatre
System
Operating Instructions
DAV-DZ560
©2008 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
About This Operating
Instructions
• The instructions in this Operating Instructions
describe the controls on the remote. You can
also use the controls on the unit if they have the
same or similar names as those on the remote.
• The Control Menu items may vary depending
on the area.
On power sources
• AC power cord (mains lead) must be changed only at
the qualified service shop.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet (mains), even if the unit itself has been turned
off.
• Install this system so that the AC power cord (mains
lead) can be unplugged from the wall socket
immediately in the event of trouble.
• “DVD” may be used as a general term for a
DVD VIDEO, DVD+RW/DVD+R, and DVD-
RW/DVD-R.
• Measurements are expressed in feet (ft) for
North American models.
• The default setting is underlined.
About the S-AIR function
The system is compatible with the S-AIR
function, which allows transmission of sound
between S-AIR products wirelessly.
The following S-AIR products can be used with
the system:
• Surround amplifier: You can enjoy surround
speaker sound wirelessly.
• S-AIR receiver: You can enjoy system sound
in another room.
These S-AIR products can be purchased as an
option (the S-AIR product lineup differs
depending on the area).
Notes or instructions for the surround amplifier
or S-AIR receiver in this operating instructions
refer only to when the surround amplifier or
S-AIR receiver is used.
For details on the S-AIR function, see “Using an
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Getting Optimal Surround Sound for a
Room.............................................. 81
Calibrating the Appropriate Settings
Automatically................................. 82
Controlling the TV with the Supplied
Remote ........................................... 83
Changing the Brightness of the Front
Panel Display.................................. 85
Step 1: Assembling
Step 4: Performing the Quick
Setup ........................................25
Step 5: Enjoying Sound from all the
Enjoying Surround Sound by Using
Decoding Mode ..............................30
Adjusting the Delay Between the Picture
and Sound .......................................48
Using the Control for HDMI Function for
“BRAVIA” Sync ............................62
Playing Back Audio Files/JPEG Image
Files of a USB Device ....................65
Using the DIGITAL MEDIA PORT
Adapter ...........................................74
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable Discs
Type
Disc logo
Characteristics
Icon
DVD VIDEO
• DVD VIDEO
• DVD-R/DVD-RW in DVD
VIDEO format or video mode
• DVD+R/DVD+RW in DVD
VIDEO format
VR (Video
Recording) mode
• DVD-R/DVD-RW in VR (Video
Recording) mode (except for
DVD-R DL)
Super Audio CD
VIDEO CD
• Super Audio CD
• VIDEO CD (Ver. 1.1 and 2.0 discs)
• Super VCD
• CD-R/CD-RW/CD-ROM in video
CD format or Super VCD format
CD
• Audio CD
• CD-R/CD-RW in audio CD format
DATA CD
–
–
• CD-R/CD-RW/CD-ROM in
DATA CD format, containing MP3
1)
2)
files , JPEG image files , and
3)4)
DivX video files , and
conforming to ISO 9660 Level 1/
5)
Level 2, or Joliet (extended format)
DATA DVD
• DVD-ROM/DVD-R/DVD-RW/
DVD+R/DVD+RW in DATA
DVD format, containing MP3
1)
2)
files , JPEG image files , and
3)4)
DivX video files , and
conforming to UDF (Universal
Disk Format)
1)MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data. MP3 files
must be in MPEG1 Audio Layer 3 format.
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2)JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association
(JEITA).)
®
3) DivX is a video file compression technology, developed by DivX, Inc.
4) DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
5)A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for
Standardization).
“DVD-RW,” “DVD+RW,” “DVD+R,”“DVD VIDEO,” and the “CD” logos are trademarks.
Example of discs that the system cannot play
The system cannot play the following discs:
• CD-ROM/CD-R/CD-RW other than those recorded in the formats listed on page 5
• CD-ROM recorded in PHOTO CD format
• Data part of CD-Extra
• CD Graphics disc
• DVD Audio
• DATA DVD that does not contain MP3 files, JPEG image files, or DivX video files
• DVD-RAM
Also, the system cannot play the following discs:
• A DVD VIDEO with a different region code (page 7)
• A disc that has a non-standard shape (e.g., card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape or a sticker still left on it
Note about CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW cannot be played on this system
due to the recording quality or physical condition of the disc, or the characteristics of the recording
device and authoring software.
The disc will not play if it has not been correctly finalized. For more information, refer to the operating
instructions for the recording device.
Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have
been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs/DATA
DVDs created in Packet Write format cannot be played.
Music discs encoded with copyright protection technologies
This product is designed to play back discs that conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with copyright protection technologies are marketed by some
record companies. Please be aware that among those discs, there are some that do not conform to the
CD standard and may not be playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital
audio material on the other side. However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not guaranteed.
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
About Multi Session CD
• This system can play a Multi Session CD when an MP3 file is contained in the first session. Any
subsequent MP3 files recorded in later sessions can also be played back.
• This system can play a Multi Session CD when a JPEG image file is contained in the first session.
Any subsequent JPEG image files recorded in later sessions can also be played back.
• If MP3 files and JPEG image files in music CD format or video CD format are recorded in the first
session, only the first session will be played back.
Region code
Your system has a region code printed on the rear of the unit and will only play a DVD labeled with
the same region code.
ALL
A DVD VIDEO labeled
will also play on this system.
If you try to play any other DVD VIDEO, the message [Playback prohibited by area limitations.] will
appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be given even
though playing the DVD VIDEO is prohibited by area restrictions.
Note about playback operations of a DVD or VIDEO CD
Some playback operations on a DVD or VIDEO CD may be intentionally set by software producers.
Since this system will play a DVD or VIDEO CD according to the disc contents the software producers
designed, some playback features may not be available. Be sure to read the operating instructions
supplied with the DVD or VIDEO CD.
Copyrights
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.
This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround
decoder and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
**Manufactured under license from DTS, Inc.
“DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.
This system incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
“BRAVIA” and
are trademarks of Sony Corporation.
“S-AIR” and its logo are trademarks of Sony Corporation.
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Unpacking
• Front speakers (2)
• FM wire antenna (aerial) (1) • Bases (2)
or
• Mounting plates (2)
• Speaker cords (6, red/white/
green/gray/blue/purple)
• Center speaker (1)
• Post covers (2)
• Remote commander
(remote) (1)
• Screws (large, with washer) (4)
• Surround speakers (2)
• R6 (size AA) batteries (2)
• Calibration mic (1)
• Screws (small) (6)
• Subwoofer (1)
• Operating Instructions
• Speaker and TV connections
(card)
• Foot pads (1 set)
• Posts (2)
• AM loop antenna (aerial) (1)
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment. To use the remote, point it at the remote sensor on the unit.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Attaching the foot pads to the subwoofer
Attach the foot pads (supplied) to the bottom of the subwoofer to stabilize the subwoofer and prevent
it from slipping.
,
Remove the foot pads from
the mount seat.
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Assembling the Speakers
Before connecting the speakers, attach the speaker stand to the speaker.
(For the front speakers)
Use the parts as follows:
• Front speakers (2)
• Speaker cords (2, red/white)
• Posts (2)
• Bases (2)
• Mounting plates (2)
• Post covers (2)
• Screws (large, with washer) (4)
• Screws (small) (6)
Note
• Spread a cloth on the floor to avoid damaging the floor when you assemble the speakers.
Tip
1
Thread the speaker cord through the hole in the base and post.
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected.
Use the speaker cords as follows:
• Front speaker (L): White
• Front speaker (R): Red
Be careful with the orientation of the post. Thread the speaker cord (and the speaker system cord)
into the end of the post that has two holes.
Post
Bottom of the base
Two holes
,
Speaker cord
Top of the base
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Attach the post cover to the other end of the post.
Orient the slot toward you, attach the post cover so that the slot of the post engages with the tab of
the post cover, then secure with the screw.
Thread the speaker cord through
the hole of the post cover.
Speaker cord
,
,
Hole
Post cover
Upper part of the
post
Screw (small)
3
Lay the post in the slot of the speaker, slide the post to the end of the slot, then secure
the post with the mounting plate and screws.
Select the speaker whose jack color on its rear panel matches the color tube of the speaker cord.
Post cover
Be careful the
orientation of the
post cover when
placing the post.
Secure two screws (large, with
washer).
,
Rear of the speaker
Mounting plate
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Connect the speaker cords to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord
with the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front speaker (L): White
Front speaker (R): Red
Rear of the speaker
5
Attach the post to the base.
Insert the post so that the slit on the lower part of the post aligns with the projection of the base,
then secure the post with the two screws.
Post
Slit
,
Projection
Base
Screws
(small)
Note
• Make sure that the slot on the post aligns with the projection of the base by rotating the post slightly.
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Adjust the height of the speaker.
Loosen (but do not remove) the screws, adjust the height of the speaker, then secure the screws.
Adjust the speaker of one side, then adjust another speaker by checking lines as a guide.
Note
• When adjusting the height of the speaker, grasp the speaker so that the speaker does not fall.
Lines
,
Post
Secure two screws.
Loosen two screws.
7
Take up any speaker cord slack.
Take up slack in the speaker cord by pulling from the bottom of the base.
Secure the speaker cord by running
it through the slot.
Adjust the length of the cord.
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Fully-assembled illustration
Front speaker (R):
Red label
Front speaker (L):
White label
Red
White
GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Positioning the System
For the best possible surround sound, all the speakers other than the subwoofer should be placed at the
same distance from the listening position (A).
However, this system allows you to place the center speaker up to 1.6 meters (5 ft) closer (B) and the
surround speakers up to 5.0 meters (16 ft) closer (C) to the front speakers.
The front speakers can be placed from 1.0 to 7.0 meters (3 to 23 ft) (A) from the listening position.
Place the system as illustrated below.
A Front speaker (L (left))
B Front speaker (R (right))
C Center speaker
D Surround speaker (L (left))
B
E Surround speaker (R (right))
F Subwoofer
G Unit
A
F
C
Top view
G
E
A
A
A
B
C
A
B
A
A
A
A
D
C
C
D
E
* Not supplied.
Note
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,
oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.
• Do not lean or hang on the speaker, as the speaker may fall down.
Tip
• When you change the positions of the speakers, Sony recommends that you change the settings. For details, see
“Getting Optimal Surround Sound for a Room” (page 81) and “Calibrating the Appropriate Settings Automatically”
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front speaker (L): White
Front speaker (R): Red
Center speaker: Green
Surround speaker (L): Blue
Surround speaker (R): Gray
1
2
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
Hole on the back of
4 mm (5/32 inch)
the speaker
5 mm
(7/32 inch)
30 mm (1 3
/16 inches)
10 mm
13
(
/32 inch)
Fasten the screws to the wall.
For the front speakers
For the center speaker
145 mm
(5 3
4 inches)
/
100 mm
4 inches
(
)
8 to 10 mm
8 to 10 mm
11
13
11
13
(
/
to
/
inch)
(
/
to
/
inch)
32
32
32
32
For the surround speakers
8 to 10 mm
11
13
(
/
to
/
inch)
32
32
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Hang the speakers on the screws.
Hole on the back of
the speaker
5 mm
(7/32 inch)
10 mm
13
(
/32 inch)
Rear of the speaker
Note
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where
reinforcement is applied.
• Contact a screw shop or installer regarding the wall material or screws to be used.
• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or
improper screw installation, natural calamity, etc.
GB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Connecting the System
See the connection diagram below, and read the additional information from 1 to 5 on the following
pages.
Note
• Be sure to make connections securely to avoid hum and noise.
• When you connect another component with a volume control, turn up the volume of the other components to a level
where sound is not distorted.
3 DIGITAL MEDIA
PORT adapter
3 Portable audio source
2 TV
4 AM loop antenna (aerial)
4 FM wire antenna (aerial)
5 AC power cord (mains lead)
1 Center speaker
1 Subwoofer
1 Front speaker (L)
1 Front speaker (R)
1 Surround speaker (R)
1 Surround speaker (L)
:Signal flow
GB
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Connecting the Speakers
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected. Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker
cord with the color tube to 3, and the speaker cord without the color tube to #. Do not catch the
speaker cord insulation in the speaker terminals.
Rear of speaker
Color tube
(+)
(–)
Connector
When connecting to the unit, insert the connector until it clicks.
Rear panel
ANTENNA
SPEAKER
FRONT SUR
FRONT
R
L
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
0.7A MAX
COAXIAL
OPTICAL
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
R
E
F
O
O
W
SPEAKER
B
U
To the surround speaker (L)
(blue)
S
R
E
T
N
E
C
To the surround speaker (R)
(gray)
L
R
SU
SPEAKESR R R
U
L
T
N
O
R
F
R
T
N
O
R
F
To the center speaker
(green)
To the subwoofer
(purple)
To the front speaker (R)
(red)
To the front speaker (L) (white)
GB
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connecting the TV
For video output to your TV, check the video input jacks of the TV, and select connection method A
or B. Picture quality improves in order from A (standard) to B (HDMI).
When the TV has the digital optical or coaxial output jack, you can improve sound quality by
connecting with the digital cord (A).
Digital optical cord
(not supplied)
Digital coaxial cord
(not supplied)
N
DIGITAL
I
OPTICAL
COAXIAL
TV
or
To the digital coaxial output jack of
the TV
To the digital optical output jack of
the TV
ANTENNA
Rear panel
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGIN
EURO AV
DC5V
0.7A MAX
COAXIAL
OPTICAL
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
HDMI* cable
(not supplied)
SCART (EURO AV) cord
(not supplied)
V
O
A
EUR
T
U
O
I
M
D
H
OUTPUT(TO TV)
To the SCART (EURO AV) jack of the TV
To the HDMI IN jack of the TV
* HDMI (High-Definition Multimedia Interface)
Note
• During the “DMPORT” function, video signal is not output from the HDMI OUT jack.
• The system can accept both digital and analog signals. Digital signals have priority over analog signals. (COAXIAL
has priority over OPTICAL.) If the digital signal ceases, the analog signal will be processed after 2 seconds.
GB
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Connecting the other components
You can enjoy the connected component using the six speakers of the system.
• Portable audio source: A
• DIGITAL MEDIA PORT adapter: B
Stereo mini-plug cord
(not supplied)
To the portable audio
source
Front panel
ANTENNA
SPEAKER
Rear panel
FRONT
R
FRONT
L
SUR
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
Screws*
0.7A MAX
COAXIAL
OPTICAL
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
5V
0.7A
C
D
X
A
M
T
R
O
M
D
DIGITAL MEDIA PORT adapter
(not supplied)
*
CAUTION
To connect the DIGITAL MEDIA PORT adapter
Connect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details, see
GB
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned. When disconnecting, pull out while
pressing A.
A
Wireless system option
By using an S-AIR product (not supplied), you can enjoy wireless performance by transmission from
the system. For details, see “Using an S-AIR Product” (page 75) or refer to the operating instructions
of the S-AIR product.
If your TV has multiple audio/video inputs
You can enjoy the sound with the speakers of the system through the connected TV. Connect the
components as follows.
VCR, digital satellite receiver
TV
or PlayStation, etc.
VCR, digital satellite receiver
or PlayStation, etc.
System
:Signal flow
Select the component on the TV. For details, refer to the operating instructions of the TV.
If the TV does not have multiple audio/video inputs, a switcher will be necessary to receive the sound
from more than two components.
GB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Connecting the antenna (aerial)
AM loop antenna (aerial)
(supplied)
A
B
Note
• Cord (A) or cord (B) can be connected to either terminal.
ANTENNA
SPEAKER
Rear panel
FRONT
R
FRONT
L
SUR
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
0.7A MAX
COAXIAL
OPTICAL
UTPUT(TO TV)
TV
HDMI OUT
DMPORT
A
N
N
TE
N
A
FM wire antenna (aerial)
(supplied)
5
7
L
M
IA
F
X
A
O
C
or
Note
• Keep the AM loop antenna (aerial) and cord away from the system or other AV components, as noise may result.
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Outdoor FM antenna (aerial)
Unit
ANTENNA
COAXIAL 75
FM
AM
GB
23
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of the unit to a wall outlet (mains), connect all the
speakers to the unit.
Rear panel
ANTENNA
SPEAKER
FRONT SUR
FRONT
R
L
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
0.7A MAX
COAXIAL
OPTICAL
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
To the wall outlet (mains)
About the demonstration
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display.
Setting the demonstration mode to on/off
1
Press [/1 on the unit.
The system turns on.
2
3
Press SYSTEM MENU.
Press X/x repeatedly until “DEMO” appears in the front panel display, then press
c.
or
4
Press X/x to select a setting.
• “DEMO ON”: On.
• “DEMO OFF”: Off.
5
6
Tip
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
• When you purchase the system from new, or if the system is at its factory default settings (ex., after performing
GB
24
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE SETUP
OSD:
Step 4: Performing the
Quick Setup
ENGLISH
ENGLISH
MENU:
AUDIO:
SUBTITLE:
FRENCH
SPANISH
PORTUGUESE
Follow the Steps below to make the basic
adjustments for using the system.
Note
• When you connect the system and the TV with the
HDMI cable (not supplied), you need to set the type
of video output for matching your TV. For details, see
5
6
Press X/x to select a language.
The system displays the menu and subtitles
in the selected language.
Press
.
The Setup Display for selecting the aspect
ratio of the TV to be connected appears.
"/1
VIDEO SETUP
TV TYPE:
LINE:
16:9
16:9
PAUSE MODE:
4:3 LETTER BOX
4:3 PAN SCAN
C/X/x/c,
7
8
Press X/x to select the setting that
matches your TV type.
DISPLAY
x If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
[16:9] (page 52)
1
2
Turn on the TV.
x If you have a 4:3 standard TV
[4:3 LETTER BOX] or [4:3 PAN SCAN]
Press [/1.
Note
• Make sure that the function is set to “DVD”
Press
.
The Setup Display for selecting the output
method for video signals from the EURO
AV T OUTPUT (TO TV) jack on the rear
panel of the unit appears.
3
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
[Press [ENTER] to run QUICK SETUP.]
appears at the bottom of the TV screen. If
this message does not appear, recall the
again.
VIDEO SETUP
TV TYPE:
LINE:
16:9
VIDEO
VIDEO
PAUSE MODE:
RGB
4
Press
without inserting a disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
GB
25
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Press X/x to select the output method
for video signals.
• [VIDEO]: outputs video signals.
• [RGB]: outputs RGB signals.
Note
• If your TV does not accept RGB signals, no
picture appears on the TV screen even if you
select [RGB]. Refer to the operating instructions
supplied with your TV.
10
11
Press
.
The Setup Display for selecting the speaker
formation appears.
Calibration mic
Press C/c to select the speaker
formation image as the speakers are
actually positioned.
For details, see “Getting Optimal Surround
SPEAKER FORMATION
STANDARD
12
13
Press
.
14
15
Press C/c to select [YES].
Connect the calibration mic to the
A.CAL MIC jack on the front panel.
Note
• Make sure that the headphones are not
connected to the unit or surround amplifier. You
cannot operate following Steps with the
headphones connected.
Set up the calibration mic at the ear level
using a tripod, etc. (not supplied). The front
of each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic.
Press
.
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
Note
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the
volume down. Give consideration to children
and neighbors.
• Before [AUTO CALIBRATION], install the
surround amplifier in the appropriate location. If
you install the surround amplifier in an improper
location, such as another room, proper
measurement will not be obtained.
• Avoid being in the measurement area and
making noise during the measurement (which
takes about 3 minutes), as it may interfere with
measurement.
GB
26
Download from Www.Somanuals.com. All Manuals Search And Download.
16
17
Unplug the calibration mic and press C/
c to select [YES].
Setting the type of video
output to match your TV
Note
• The environment of the room in which the
system is installed may affect measurements.
• If measurement fails, follow the message then
retry [AUTO CALIBRATION].
Depending on the connection of the TV
(page 20), select the type of video output of the
system.
Press
.
To select the type of video signal
output from the HDMI OUT jack
Quick Setup is finished. All connections
and setup operations are complete.
When you connect the unit and the TV with the
HDMI cable, select the type of video signals
output from the HDMI OUT jack.
To quit the Quick Setup
Press
DISPLAY in any Step.
For details, refer also to the operating
Tip
instructions supplied with the TV/projector, etc.
• If you change the position of the speakers, reset the
speaker settings. See “Getting Optimal Surround
• If you want to change any of the settings, see “Using
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
To recall the Quick Setup display
The Control Menu display appears on the
TV screen.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
3
4
5
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
2
Press
in stop mode.
DISPLAY while the system is
Press X/x to select [CUSTOM], then
The Control Menu display appears on the
TV screen.
press
.
The Setup Display appears.
3
4
Press X/x to select
then press
[SETUP],
Press X/x to select [HDMI SETUP], then
.
press
.
The options for [SETUP] appear.
The options for [HDMI SETUP] appear.
6
7
Press X/x to select [HDMI
94( 99)
1( 1)
0: 01: 08
DVD VIDEO
RESOLUTION], then press
Press X/x to select the desired setting,
then press
.
T
.
CUSTOM
CUSTOM
QUICK
• [AUTO (1920 × 1080p)]: The system
outputs the optimal video signal for the
connected TV.
• [1920 × 1080i]: The system outputs 1920
× 1080i* video signals.
Press X/x to select [QUICK], then press
.
• [1280 × 720p]: The system outputs 1280 ×
720p* video signals.
The Quick Setup display appears.
• [720 × 480p]**: The system outputs 720 ×
480p* video signals.
* i: interlace, p: progressive
GB
27
Download from Www.Somanuals.com. All Manuals Search And Download.
**Depending on the country model, [720 × 576p]
may appear.
Step 5: Enjoying Sound
from all the Speakers
Note
• When “HDMI” lights up in the front panel display,
images other than [720 × 480p] or [720 × 576p] are
stretched vertically.
You can enjoy DVD, TV, or VCR sound from
all the speakers in this system.
FUNCTION
+/–
SYSTEM
MENU
X/x/c,
1
Press FUNCTION +/– repeatedly until
the desired function appears in the
front panel display.
Each time you press FUNCTION +/–, the
function changes as follows.
“DVD” t “TUNER FM” t “TUNER
AM” t “USB” t “TV” t “DMPORT”
t “AUDIO” t …
Function
Source
“DVD”
Disc that is played by the
system
“TUNER FM”/
“TUNER AM”
FM/AM radio (page 58)
“USB”
“TV”
USB device (page 65)
TV (or the component that
is connected to the TV
jacks on the rear panel)
“DMPORT”
“AUDIO”
DIGITAL MEDIA PORT
adapter (page 74)
Portable audio source (that
is connected to the AUDIO
IN jack on the front panel)
GB
28
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Press FUNCTION +/– repeatedly until
“TV” or “AUDIO” appears in the front
panel display.
Note
• When you use the TV (COAXIAL or OPTICAL
DIGITAL IN) jack (digital connection), the
digital connection takes priority.
2
3
Press SYSTEM MENU.
2
3
Press SYSTEM MENU.
Press X/x repeatedly until
“ATTENUATE” appears in the front
Press X/x repeatedly until “DEC.
MODE” appears in the front panel
panel display, then press
or c.
display, then press
or c.
4
Press X/x to select a setting.
4
Press X/x repeatedly until the
decoding mode you want appears in
the front panel display.
• “ATT ON”: You can attenuate the input
level. The output level is changed.
• “ATT OFF”: Normal input level.
When you want to output the TV sound or
stereo sound of a 2 channel source from the
six speakers, select the “PRO LOGIC,”
“PLII MOVIE,” or “PLII MUSIC”
decoding mode.
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
For details, see page 30.
5
Press
.
The setting is made.
6
Press SYSTEM MENU.
The system menu turns off.
Note
• Depending on your TV, you may need to turn off your
TV’s speaker to enjoy surround sound of the system.
Tip
• When listening to audio files using a portable audio
source, you can enhance the sound.
Press FUNCTION +/– to select “AUDIO.” Connect
the portable audio source. Select “A.F.D. STD” for
“DEC. MODE.”
To cancel, select other than “A.F.D. STD.”
Changing the input level of the
sound from connected
components
Distortion may occur when you listen to a
component connected to the EURO AV T
OUTPUT (TO TV) jack on the rear panel, or to
the AUDIO IN jack on the front panel.
Distortion is not a malfunction and will depend
on the component connected.
To prevent distortion, reduce the input level on
the unit.
GB
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Adjustment
Enjoying Surround Sound by Using Decoding Mode
You can enjoy surround sound simply by selecting one of the system’s pre-programmed decoding
modes. They bring exciting and powerful sound of movie theaters into your home.
SYSTEM
MENU
X/x/c,
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c.
3
Press X/x repeatedly until the decoding mode you want appears in the front panel
display.
Display
Decoding mode
Effect
“A.F.D. STD”
AUTO FORMAT
DIRECT
Presents sound as it was recorded/encoded.
Depending on the source, the speakers that output sound will vary.
STANDARD
“A.F.D. MULTI” AUTO FORMAT
DIRECT MULTI
2 channel source: Sound that is recorded in 2 channel (front left and
right channel) is also assigned to the surround left and right channel.
This mode outputs sound from the front left and right speakers,
surround left and right speakers, and subwoofer. The center speaker
does not output any sound.
Multi channel source: Depending on the source, speakers that output
the sound will vary.
“PRO LOGIC”
Dolby Pro Logic
Performs Pro Logic decoding to the input signal and simulates
surround sound from 2 channel sources.
This mode outputs sound from all the speakers and subwoofer. Sound
may not be output from all speakers depending on the source.
GB
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Decoding mode
Effect
“PLII MOVIE”
Dolby Pro Logic II
MOVIE
Performs Pro Logic II movie mode decoding to the input signal and
produces five full-bandwidth output channels from 2 channel sources.
This setting is ideal for watching videos of overdubbed or old movies.
This mode outputs sound from all the speakers and subwoofer. Sound
may not be output from all speakers depending on the source.
“PLII MUSIC”
Dolby Pro Logic II
MUSIC
Performs Pro Logic II music mode decoding to the input signal and
produces five full-bandwidth output channels from 2 channel sources.
This setting is ideal for normal stereo sources such as a CD.
This mode outputs sound from all the speakers and subwoofer. Sound
may not be output from all speakers depending on the source.
“2CH STEREO”
“HP 2CH”
2 CHANNEL
STEREO
Outputs the sound from the front left and right speakers and
subwoofer. Multi channel surround formats are downmixed to 2
channels.
HEADPHONE
2 CHANNEL
STEREO
Outputs the sound from headphone left and right. Multi channel
surround formats are downmixed to 2 channels.
“HP VIRTUAL”
HEADPHONE
VIRTUAL
Outputs the sound as surround from headphone left and right. This
mode is effective only when a multi channel source is played.
4
5
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
To turn the surround effect off
Select “A.F.D. STD” or “2CH STEREO” for “DEC. MODE.”
Note
• When the input signal is multi channel source, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are canceled
and the multi channel source is output directly.
• When the bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• You cannot select the decoding mode when the unit is reading the files in the USB device or recording/copying
songs.
• Depending on the input stream, the decoding mode may not be effective.
• When you select “A.F.D. MULTI,” the surround or stereo effect may not be effective. In this case, select “A.F.D.
STD,” “PRO LOGIC,” “PLII MOVIE,” or “PLII MUSIC.”
• When changing the decoding mode while using the S-AIR receiver, sound from the S-AIR receiver may skip.
GB
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Sound
Mode
You can select a suitable sound mode for movies
or music.
Enjoying Multiplex
Broadcast Sound
(DUAL MONO)
You can enjoy multiplex broadcast sound when
the system receives or plays the Dolby Digital
multiplex broadcast signal.
Note
• To receive the Dolby Digital signal, you need to
connect a TV or other component to the unit with an
digital output mode of the TV or other component to
Dolby Digital.
SOUND
MODE
AUDIO
Press SOUND MODE repeatedly during
playback until the desired mode appears in
the front panel display.
• “AUTO”: The system selects “MOVIE” or
“MUSIC” automatically to produce the sound
effect depending on the disc.
• “MOVIE”: The system provides the sound for
movies.
Press AUDIO repeatedly until the desired
signal appears in the front panel display.
• “MUSIC”: The system provides the sound for
music.
• “MAIN”: Sound of the main language will be
output.
Note
• You cannot operate these setup items when you
connect headphones to the unit or surround amplifier.
• When changing the sound mode while using the
S-AIR receiver, sound from the S-AIR receiver may
skip.
• “SUB”: Sound of the sub language will be
output.
• “MAIN+SUB”: Mixed sound of both the main
and sub languages will be output.
GB
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Load a disc.
Place one disc on the tray, and then press A.
Disc
Playing a Disc
Depending on the DVD VIDEO or VIDEO CD,
some operations may be different or restricted.
Refer to the operating instructions supplied with
your disc.
Note
• When you play an 8 cm disc, place it on the
inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
• Do not forcibly press the disc tray closed with
your finger, as this may cause malfunction.
• Do not place more than one disc on the tray.
Adjust the volume
"/1
H
FUNCTION
A
6
7
Press H.
The system starts playback (continuous
play).
Disc tray
Connect
headphones
Adjust the volume by using VOLUME +/
– on the remote or the VOLUME control
on the unit.
"/1
The volume level appears on the TV screen
and in the front panel display.
FUNCTION
+/–
Note
• Depending on the system status, the volume level
may not appear on the TV screen.
• When you set the Control for HDMI function to on,
the TV that is connected to the system with an HDMI
cable (not supplied) can be sync-operated with the
system. For details, see “Using the Control for HDMI
MUTING
VOLUME +/–
STEP
/
/
,
./>
H
/m/
M/
To turn the system off
Press "/1 while the system is on. The system
enters standby mode.
x
X
1
2
Turn on your TV.
To save power in standby mode
Press "/1 while the system is on.
To enter power saving mode, make sure that the
system is in the following status.
Switch the input selector on the TV to
this system.
3
Press "/1.
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION +/– to select “DVD.”
– [CONTROL FOR HDMI] is set to [OFF]
4
Press A.
GB
33
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the headphones
To
Press
Connect the headphones to PHONES jack on the
unit. The sound of the system is muted.
You can also connect the headphones to
PHONES jack on the surround amplifier. (The
sound of the system is muted.)
Play one frame at a time STEP
to go to the next
3)5)6)
(Freeze Frame)
frame while the system is in
pause mode. Press STEP
to go to the preceding
frame while the system is in
pause mode (DVD VIDEO/
DVD-R/DVD-RW only).
To return to normal
Other operations
playback, press H.
To
Press
x
Replay the previous
scene (10 seconds
before)
(instant replay) during
playback.
Stop
Pause
7)
X
Briefly fast forward the
current scene (30
seconds after)
(instant advance)
during playback.
Resume play after pause X or H
Go to the next chapter,
>
8)
1)
track, or scene
1)Except for JPEG image files.
Go back to the
. twice in a second.
When you press . once,
you can go to the beginning
of the current chapter,
track, or scene.
preceding chapter,
2)Scan speeds may differ with some discs.
3)DVD VIDEO, DVD-R, DVD-RW, VIDEO CD only.
4)Except for VIDEO CDs.
1)
track, or scene
Turn off the sound
temporarily
MUTING.
5)You cannot search for a still picture on a DVD-VR.
6)For a DATA CD/DATA DVD, this function works
only for DivX video files.
7)DVD VIDEO/DVD-RW/DVD-R only. The button
can be used except for DivX video files.
8)DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
DVD+R only. The button can be used except for
DivX video files.
To cancel, press it again or
VOLUME + to adjust the
sound volume.
Stop play and remove
the desired disc
A on the unit.
Locate a point quickly M/
by playing a disc in fast playing a disc. Each time
or
/m while
forward or fast reverse you press M/
or
/
1)2)
Note
(Scan)
m during scan, the
• You may not be able to use the instant replay or
instant advance function with some scenes.
playback speed changes.
To return to normal speed,
press H. Actual speeds
may differ with some discs.
4)
Displaying multi-angles and
subtitles
Watch frame by frame M/
or
/m
3)
(Slow-motion Play)
while the system is in pause
mode. Each time you press
4)
M/
or
/m
To change the angles
during Slow-motion Play,
the playback speed
changes. Two speeds are
available. To return to
normal playback speed,
press H.
If various angles (multi-angles) for a scene are
recorded on a DVD VIDEO, you can change the
viewing angle.
Press ANGLE during playback to select the
desired angle.
Note
• Depending on the DVD VIDEO, you may not be able
to change the angle even if multi-angles are recorded
on the DVD VIDEO.
GB
34
Download from Www.Somanuals.com. All Manuals Search And Download.
displayed two or more times, the DVD VIDEO
is recorded in multiple audio formats.
To display the subtitles
x DVD-VR
If subtitles are recorded on a disc, you can turn
the subtitles on/off during playback. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language during
playback, or turn the subtitles on/off whenever
you want.
The types of sound tracks recorded on a disc are
displayed.
Example:
• [1: MAIN] (main sound)
• [1: SUB] (sub sound)
• [1: MAIN+SUB] (main and sub sound)
• [2: MAIN]
Press SUBTITLE during playback to select
the desired subtitle language.
• [2: SUB]
Note
• [2: MAIN+SUB]
• Depending on the DVD VIDEO, you may not be able
to change the subtitles even if multilingual subtitles
are recorded on the disc. You also may not be able to
turn them off.
Note
• [2: MAIN], [2: SUB], and [2: MAIN+SUB] do not
appear when one audio stream is recorded on the disc.
• You can change the subtitles if the DivX video file
has an “.AVI” or “.DIVX” extension and contains
subtitle information within the same file.
x VIDEO CD/CD/DATA CD (MP3 file)/DATA
DVD (MP3 file)
• [STEREO]: The standard stereo sound.
• [1/L]: The sound of the left channel
(monaural).
Changing the sound
• [2/R]: The sound of the right channel
(monaural).
x DATA CD (DivX video file)/DATA DVD
(DivX video file)
The choice of DATA CD or DATA DVD audio
signal formats differ, depending on the DivX
video file contained on the disc. The format is
shown in the display.
When the system is playing a DVD VIDEO or
DATA CD/DATA DVD (DivX video files)
recorded in multiple audio formats (PCM,
Dolby Digital, MPEG audio, or DTS), you can
change the audio format. If the DVD VIDEO is
recorded with multilingual tracks, you can also
change the language.
With a VIDEO CD, CD, DATA CD, or DATA
DVD, you can select the sound from the right or
left channel and listen to the sound of the
selected channel through both the right and left
speakers.
x Super VCD
• [1:STEREO]: The stereo sound of the audio
track 1.
• [1:1/L]: The sound of the left channel of the
audio track 1 (monaural).
• [1:2/R]: The sound of the right channel of the
audio track 1 (monaural).
You cannot change the sound for a Super Audio
CD.
• [2:STEREO]: The stereo sound of the audio
track 2.
• [2:1/L]: The sound of the left channel of the
audio track 2 (monaural).
Press AUDIO repeatedly during playback to
select the desired audio signal.
• [2:2/R]: The sound of the right channel of the
audio track 2 (monaural).
x DVD VIDEO
Depending on the DVD VIDEO, the choice of
language varies.
Note
• While the system is playing a Super VCD on which
the audio track 2 is not recorded, no sound will come
out when you select [2:STEREO], [2:1/L], or [2:2/R].
When 4 digits are displayed, they indicate a
language code. See “Language Code List”
(page 105) to confirm which language the code
represents. When the same language is
GB
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the audio signal
format
Selecting a playback area for a
Super Audio CD
If you press AUDIO repeatedly during
playback, the format of the current audio signal
(PCM, Dolby Digital, DTS, etc.) appears as
shown below.
selecting the playback area.
To select a playback area on a 2
channel + Multi-channel Super
Audio CD
Some Super Audio CDs consist of a 2 channel
playback area and a multi-channel playback
area. You can select the playback area you want
to listen to.
x DVD
Example:
Dolby Digital 5.1 channel
LFE (Low
Frequency Effect)
Surround (L/R)
1
Press
in stop mode.
DISPLAY while the system is
1: ENGLISH
DOLBY DIGITAL 3 / 2 .1
The Control Menu display appears on the
TV screen.
L
C
R
Front (L/R) +
Center
LFE
LS
RS
2
3
Press X/x to select
2CH], then press
[MULTI/
.
Currently playing program format
The options for [MULTI/2CH] appear.
Press X/x to select the desired setting
Example:
and press
.
Dolby Digital 3 channel
• [MULTI]: You can play the multi-channel
playback area.
Surround
(Monaural)
• [2CH]: You can play the 2 channel
playback area.
Front (L/R)
Note
1:SPANISH
DOLBY DIGITAL 2 / 1
L
• You cannot change the playback area during
playback.
R
S
To change a playback layer when
playing a hybrid Super Audio CD
Some Super Audio CDs consist of an HD layer
and a CD layer. You can change the playback
layer you want to listen to.
Currently playing program format
x DATA CD (DivX video file)/DATA DVD
(DivX video file)
Note
Example:
• When the Super Audio CD does not have the HD
layer, you cannot select the playback layer.
MP3 audio
1
Press
in stop mode.
DISPLAY while the system is
1:MP3
128k
The Control Menu display appears on the
TV screen.
Bit rate
2
Press X/x to select
AUDIO CD/CD LAYER], then press
[SUPER
.
GB
36
Download from Www.Somanuals.com. All Manuals Search And Download.
x When the current layer is the CD
layer
[SUPER AUDIO CD] appears.
To go back to the menu
Press O RETURN.
Note
x When the current layer is the HD
layer
[CD] appears.
• Depending on the VIDEO CD, [Press ENTER] in
Step 3 may appear as [Press SELECT] in the
operating instructions supplied with the disc. In this
case, press H.
3
Press
to change the layer.
Tip
• [SUPER AUDIO CD]: You can play the
HD layer.
When the system is playing an HD layer,
“SA-CD” lights up in the front panel
display
• To play without using the PBC function, press ./
> or the number buttons while the system is in stop
mode to select a track, then press H or
system starts playback. You cannot play still pictures
such as a menu. To return to PBC playback, press x
twice, then press H.
. The
• [CD]: You can play the CD layer.
When the system is playing a CD layer,
“CD” lights up in the front panel display.
Resuming playback from the
point where you stopped the
disc
Note
• Each play mode function works only within the
selected layer or playback area.
• When you select a CD layer, you cannot change a
playback area.
(Resume Play)
• Super Audio CD audio signals are not output from the
HDMI OUT jack.
When you stop the disc, the system remembers
the point where you pressed x and “RESUME”
appears in the front panel display. As long as
you do not remove the disc, Resume Play will
work even if the system is set to standby mode
by pressing "/1.
Playing a VIDEO CD with PBC
functions (Ver.2.0)
(PBC Playback)
1
While playing a disc, press x to stop
playback.
With PBC (Playback Control) functions, you
can enjoy simple interactive operations, search
functions, and other such operations.
PBC playback allows you to play a VIDEO CD
interactively by following the menu on the TV
screen.
“RESUME” appears in the front panel
display.
2
Press H.
The system starts playback from the point
where you stopped the disc in Step 1.
1
Start playing a VIDEO CD with PBC
functions.
Note
The menu for your selection appears.
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
point.
2
Select the item number you want using
the number buttons.
• The point where you stopped playing may be cleared
when:
3
4
Press
.
– you eject the disc.
Follow the instructions in the menu for
interactive operations.
– the system enters standby mode (DATA CD/
DATA DVD only).
Refer to the operating instructions supplied
with the disc, as the operating procedure
may differ depending on the VIDEO CD.
– you change or reset the settings on the Setup
Display.
– you change the parental control level.
GB
37
Download from Www.Somanuals.com. All Manuals Search And Download.
– you change the function by pressing FUNCTION
+/–.
Using Play Mode
– you disconnect the AC power cord (mains lead).
• For a DVD-VR, VIDEO CD, Super Audio CD, CD,
DATA CD, or DATA DVD, the system remembers
the resume playback point for the current disc.
• Resume Play does not work during Program Play and
Shuffle Play.
Creating your own program
(Program Play)
• This function may not work properly with some
discs.
You can play the contents of a disc in the order
you want by arranging the order of the tracks on
the disc to create your own program. You can
program up to 99 tracks.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
1
2
3
Press
DISPLAY.
To enjoy a disc that is played
before by resume playback
The Control Menu display appears on the
TV screen.
(Multi-disc Resume)
Press X/x to select
then press
[PROGRAM],
.
This system recalls the point where you stopped
the disc the last time it was played and resumes
playback from that point the next time you insert
the same disc. When the resume playback
memory is full, the resume playback point for
the earliest disc is deleted.
To activate this function, set [MULTI-DISC
RESUME] in [SYSTEM SETUP] to [ON]. For
details, see “[MULTI-DISC RESUME] (DVD
The options for [PROGRAM] appear.
Press X/x to select [SET t], then
press
.
Total time of the programmed tracks
PROGRAM
0: 00:00
T
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
Note
• This system can store at least 10 resume playback
points.
• If [MULTI-DISC RESUME] in [SYSTEM SETUP]
when you change the function by pressing
FUNCTION +/–.
Tracks recorded on a disc
4
5
Press c.
The cursor moves to the track row [T] (in
this case, [01]).
Tip
• To play from the beginning of the disc, press x twice,
then press H.
PROGRAM
0: 00:00
T
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
Select the track you want to program.
For example, select track [02].
Press X/x to select [02] under [T], then
press
.
GB
38
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel all of the tracks in the
programmed order
Selected track
PROGRAM
0: 03:51
T
1
Follow Steps 1 to 3 of “Creating your
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
02
– –
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
2
3
Press X and select [ALL CLEAR].
Press
.
Playing in random order
Total time of the programmed tracks
(Shuffle Play)
6
7
To program other tracks, repeat Steps
4 to 5.
The programmed tracks are displayed in the
selected order.
You can play the contents on a disc in random
order. Subsequent Shuffle Play may produce a
different playing order.
Press H to start Program Play.
Program Play starts.
Note
• Same song may be played repeatedly when you are
playing MP3 files.
When the program ends, you can restart the
same program again by pressing H.
1
2
3
Press
DISPLAY during playback.
To return to normal play
Press CLEAR while the display for the program
setting is not displayed on the TV screen, or
select [OFF] in Step 3. To play the same
program again, select [ON] in Step 3 and press
.
The Control Menu display appears on the
TV screen.
Press X/x to select
then press
[SHUFFLE],
.
The options for [SHUFFLE] appear.
Press X/x to select the item to be
shuffled.
To turn off the Control Menu
display
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
• [TRACK]: You can shuffle tracks on the
disc.
To change or cancel a program
x During Program Play
• [OFF]: Off.
1
2
Follow Steps 1 to 3 of “Creating your
• [ON]: You can shuffle tracks selected in
Program Play.
Press X/x to select the program
number of the track you want to
change or cancel.
x DATA CD (except for DivX video file)/
DATA DVD (except for DivX video file)
• [OFF]: Off.
If you want to delete the track from the
program, press CLEAR.
• [ON (MUSIC)]: You can shuffle MP3
files in the folder on the current disc.
When no folder is selected, the first folder
will play in random order.
3
Follow Step 5 for new programming.
To cancel a program, select [--] under [T],
then press
.
4
Press
.
Shuffle Play starts.
GB
39
Download from Www.Somanuals.com. All Manuals Search And Download.
• [FOLDER]: You can repeat the current
folder.
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
• [TRACK] (MP3 files only): You can
repeat the current file.
To turn off the Control Menu
display
• [FILE] (DivX video files only): You can
repeat the current file.
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
4
Press
.
Note
The item is selected.
• You cannot use Shuffle Play with a VIDEO CD or
Super VCD with PBC playback.
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
Playing repeatedly
(Repeat Play)
To turn off the Control Menu
display
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
Note
• You cannot use Repeat Play with a VIDEO CD or
Super VCD with PBC playback.
You can play the contents on a disc repeatedly.
You can use a combination of Shuffle Play or
Program Play modes.
• When the system is playing a DATA CD/DATA
DVD which contains MP3 files and JPEG image
files, and their playing time is not the same, the audio
sound will not match the image.
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
• When [MODE (MUSIC, IMAGE)] is set to [IMAGE]
(page 44), you cannot select [TRACK].
Press X/x to select
then press
[REPEAT],
.
The options for [REPEAT] appear.
Press X/x to select the item to be
repeated.
x DVD VIDEO/DVD-VR
• [OFF]: Off.
• [DISC]: You can repeat all of the titles on
the disc.
• [TITLE]: You can repeat the current title
on a disc.
• [CHAPTER]: You can repeat the current
chapter.
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
• [DISC]: You can repeats all of the tracks
on the disc.
• [TRACK]: You can repeat the current
track.
x DATA CD/DATA DVD
• [OFF]: Off.
• [DISC]: You can repeat all of the folders
on the disc.
GB
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting [ORIGINAL] or [PLAY
LIST] on a DVD-VR
Searching/Selecting a
Disc
This function is only available for DVD-VRs
with a playlist created.
Using the DVD’s menu
1
2
3
Press
in stop mode.
DISPLAY while the system is
A DVD is divided into a lot of sections, which
make up a picture or music feature. These
sections are called “titles.” When you play a
DVD which contains several titles, you can
select the title you want using DVD TOP
MENU.
When you play a DVD that allows you to select
items such as the language for the subtitles and
the language for the sound, select these items
using DVD MENU.
The Control Menu display appears on the
TV screen.
Press X/x to select
PLAY LIST], then press
[ORIGINAL/
.
The options for [ORIGINAL/PLAY LIST]
appear.
Press X/x to select a setting.
• [PLAY LIST]: You can play the titles
created from [ORIGINAL] for editing.
• [ORIGINAL]: You can play the titles
originally recorded.
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary depending
on the disc.
4
Press
.
2
3
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
Searching for a title/chapter/
track/scene, etc.
Press
.
To display the DVD’s menu on the
Control Menu display
You can search a DVD VIDEO/DVD-VR by
title or chapter, and you can search a VIDEO
CD/Super Audio CD/CD/DATA CD/DATA
DVD by track, index, or scene. For a DATA CD/
DATA DVD, you can search by folder or file.
As titles and tracks are assigned unique numbers
on the disc, you can select the desired title or
track by entering its number. Or, you can search
for a scene using the time code.
1
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X/x to select
MENU], then press
[DISC
.
The options for [DISC MENU] appear.
3
4
Press X/x to select [MENU] or [TOP
MENU].
1
Press
DATA CD/DATA DVD with JPEG image
files, press DISPLAY twice.)
DISPLAY. (When playing a
Press
.
To turn off the Control Menu
display
Press
The Control Menu display appears on the
TV screen.
DISPLAY repeatedly until the Control
Menu display is turned off.
2
Press X/x to select the search method.
Example:
[CHAPTER]
[** (**)] is selected (** refers to a number).
GB
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Input the time code using the number
buttons.
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, folders, or files.
For example, to find the scene at 2 hours, 10
minutes, and 20 seconds after the
beginning. Press 2, 1, 0, 2, 0 ([2:10:20]).
98( 99)
13( 99)
DVD VIDEO
T
0: 03: 17
4
Press
.
Note
• You cannot search for a scene on a DVD+RW using
the time code.
Selected row
3
4
Press
.
[** (**)] changes to [– – (**)].
98( 99)
3( 99)
T
DVD VIDEO
0: 03: 17
Press X/x or the number buttons to
select the desired number of the title,
chapter, track, index, scene, etc.
If you make a mistake, press CLEAR to
cancel the number.
5
Press
.
The system starts playback from the
selected number.
Tip
• When the Control Menu display is turned off, you can
search for a chapter (DVD VIDEO/DVD-R/DVD-
RW), track (VIDEO CD/Super Audio CD/CD), or
file (DATA CD/DATA DVD (DivX video file)) by
pressing the number buttons and
.
To search for a scene using the
time code
1
2
In Step 2, select
[TIME].
[T **:**:**] (playing time of the current
title) is selected.
Press
.
[T **:**:**] changes to [T --:--:--].
GB
42
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press X/x to select a folder.
Playing MP3 Files/JPEG
Image Files
x To play MP3 files in a folder
Press H to start playing the selected
folder.
x To select a MP3 file
Press
.
You can play the MP3 files or JPEG image files:
• which have the extension “.MP3” (MP3 file)
or “.JPG”/“.JPEG” (JPEG image file)
The list of files contained in the folder
appears.
TRACK LIST
• which conform to the DCF* image file format
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan
Electronics and Information Technology Industries
Association (JEITA).
03 In the Middle of Nowher...
01_Geronimo_s_Cadillac
02_Riding_On_A_White_Swan
03_Give_Me_Peace_On_Earth
04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
06_Lonely_Tears_In_Chinatown
07_In_Shaire
Note
• The system will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG” even if they are not in
MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
Press X/x to select a file and press
.
The system starts playing the selected file.
You can turn the file list off by pressing
DVD MENU. Pressing DVD MENU again
will display the folder list.
• The system does not conform to audio in MP3PRO
format.
• The system can recognize up to 200 folders, and will
not play any folders beyond the 200th. (Depending on
the folder configuration, the number of folders that
can be recognized by the system may decrease.)
• The system can recognize up to 150 MP3 files/JPEG
image files in a folder.
To stop playback
Press x.
To play the next or previous MP3
file
• The system may take longer time to playback, when
progressing to the following folder or jump to other
folder.
Press >/.. Note that you can select the
next folder by continuing to press > after the
last file on the current folder, but that you cannot
return to the previous folder by pressing ..
To return to the previous folder, select the folder
from the folder list.
• The system may not play certain types of JPEG image
files (ex. a JPEG image file that is less than 8 (width)
× 8 (height)).
To return to the previous display
Selecting an MP3 file or folder
Press O RETURN.
1
Load a DATA CD or DATA DVD.
To turn off the display
The folders recorded on the DATA CD or
DATA DVD appear. When a folder is being
played, its title is shaded.
Press DVD MENU.
Selecting a JPEG image file or
folder
FOLDER LIST
01 Let's Talk About Love (1985)
02 1st Album (1986)
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
1
Load a DATA CD or DATA DVD.
The folders recorded on the DATA CD or
DATA DVD appear. When a folder is being
played, its title is shaded.
08 Alone (1999)
GB
43
Download from Www.Somanuals.com. All Manuals Search And Download.
return to the previous folder, select the folder
from the folder list.
FOLDER LIST
01 Let's Talk About Love (1985)
02 1st Album (1986)
To rotate a JPEG image file
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
When a JPEG image file is displayed on the TV
screen, you can rotate the JPEG image file by 90
degrees.
Press X/x while viewing a JPEG image file.
Press CLEAR to return to normal view.
08 Alone (1999)
2
Press X/x to select a folder.
Note
• You cannot rotate the JPEG image file when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
× 1080i) HD
x To play JPEG image files in a folder
Press H to start playing the selected
folder.
To stop playback
x To select a JPEG image file by
displaying the subscreens
Press PICTURE NAVI.
Press x.
Images of JPEG image files in the folder
appear in 16 subscreens.
Displaying the list of MP3
files/JPEG image files
1
2
3
4
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
5
6
7
8
9
10
14
11
15
12
16
Press X/x to select
[BROWSING], then press
.
13
The options for [BROWSING] appear.
Press C/X/x/c to select the JPEG image
file you want to view, then press
Press X/x to select the desired list,
then press
.
.
To return to normal screen, press O
RETURN.
• [FOLDER LIST]: The list of folders
appears. Follow Step 2 of “Selecting an
• [PICTURE LIST]: Images of JPEG image
files in the folder appear in 16 subscreens.
Follow Step 2 of “Selecting a JPEG image
Note
• PICTURE NAVI does not work when you set
[MODE (MUSIC, IMAGE)] to [MUSIC].
Tip
• A scroll box is displayed at the right side of the
TV screen. To display the additional JPEG
image files, select the bottom JPEG image file
and press x. To return to the previous JPEG
image file, select the top JPEG image file and
press X.
Playing MP3 files and JPEG
image files as a slide show
with sound
To play the next or previous JPEG
image file
Press c/C when the Control Menu display is not
displayed. Note that you can select the next
folder by continuing to press c after the last
image on the current folder, but that you cannot
return to the previous folder by pressing C. To
You can play a slide show with sound by first
placing both MP3 files and JPEG image files in
the same folder on a DATA CD or DATA DVD.
1
Load a DATA CD or DATA DVD.
GB
44
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
4
Press
in stop mode.
DISPLAY while the system is
• [FAST]: You can set the duration shorter
than [NORMAL].
The Control Menu display appears on the
TV screen.
• [SLOW 1]: You can set the duration
longer than [NORMAL].
• [SLOW 2]: You can set the duration
longer than [SLOW 1].
Press X/x to select
(MUSIC, IMAGE)], then press
[MODE
.
4
Press
.
The options for [MODE (MUSIC,
IMAGE)] appear.
Note
• Some JPEG image files may take longer to display
than the option you selected. Especially progressive
JPEG image files or JPEG image files of 3,000,000
pixels or more.
Press X/x to select a setting.
• [AUTO]: You can play both the JPEG
image files and MP3 files in the same
folder as a slide show.
• Duration of interval depends on the [JPEG
RESOLUTION] setting in [HDMI SETUP]
• [MUSIC]: You can play only MP3 files
continuously.
• [IMAGE]: You can play only JPEG
image files as a slide show.
To select an effect for JPEG
image files in the slide show
5
6
Press
.
1
2
3
Press
DISPLAY twice.
Press DVD MENU.
The Control Menu display appears on the
TV screen.
The list of folders recorded on the DATA
CD or DATA DVD appears.
Press X/x to select
then press
[EFFECT],
7
Press X/x to select the desired folder
and press H.
.
The options for [EFFECT] appear.
The system starts playing the selected
folder.
Press X/x to select a setting.
You can turn the folder list on/off by
pressing DVD MENU repeatedly.
• [MODE 1]: The JPEG image file sweeps
in from top to bottom.
• [MODE 2]: The JPEG image file stretches
out from left to right of the TV screen.
• [MODE 3]: The JPEG image file stretches
out from the center of the TV screen.
• [MODE 4]: The JPEG image files
randomly cycle through the effects.
• [MODE 5]: The next JPEG image file
slides over the previous image.
Note
• PICTURE NAVI does not work when [MUSIC] is
selected.
• If you play large MP3 file and JPEG image file at the
same time, the sound may skip. Sony recommends
that you set the MP3 bit rate to 128 kbps or lower
when creating the file. If the sound still skips, reduce
the size of the JPEG image file.
• [OFF]: Off.
To select the slide show duration
of JPEG image files
4
Press
.
1
2
3
Press
DISPLAY twice.
Note
• The [EFFECT] setting is not effective when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
The Control Menu display appears on the
TV screen.
× 1080i) HD
Press X/x to select
then press
[INTERVAL],
.
The options for [INTERVAL] appear.
Press X/x to select a setting.
• [NORMAL]: You can set to the standard
duration.
GB
45
Download from Www.Somanuals.com. All Manuals Search And Download.
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
Enjoying DivX® Videos
Tip
• For details about playable MP3 audio tracks or JPEG
image files on a DATA CD or DATA DVD, see
About DivX video files
Note
• The system may not play a DivX video file when the
file has been combined from two or more DivX video
files.
®
DivX is a video file compression technology,
developed by DivX, Inc. This product is an
®
• The system cannot play a DivX video file of size
more than 720 (width) × 576 (height) or 2GB.
• Depending on the DivX video file, sound may skip or
not match the pictures on the TV screen.
• The system cannot play some DivX video files that
are longer than 3 hours.
official DivX Certified product.
You can play a DATA CD or DATA DVD that
®
contains DivX video files.
A DATA CD or DATA DVD that the
system can play
• Depending on the DivX video file, the picture may
pause or be unclear. In which case, it is recommended
that you create the file at a lower bit rate. If the sound
is still noisy, MP3 is the recommended audio format.
Note, however, this system does not conform to
WMA (Windows Media Audio) format for playing
DivX files.
Playback of a DATA CD (CD-ROM/CD-R/CD-
RW) or DATA DVD (DVD-ROM/DVD-R/
DVD-RW/DVD+R/DVD+RW) on this system
is subject to certain conditions:
– With a DATA CD/DATA DVD that contains
DivX video files in addition to MP3 audio
tracks or JPEG image files, the system plays
only the DivX video files.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H for the picture to appear.
However, this system only plays a DATA CD of
format ISO 9660 Level 1/Level 2 or Joliet, and a
DATA DVD of Universal Disk Format (UDF).
Refer to the operating instructions supplied with
the disc drives and the recording software (not
supplied) for details on the recording format.
Selecting a folder
1
Press DVD MENU.
A list of folders on the disc appears. Only
folders that contain DivX video files are
listed.
About playback order of data on a
DATA CD or DATA DVD
Note that the playback order may not be
applicable, depending on the software used for
creating the DivX video file, or if there are more
than 200 folders and 150 DivX video files in
each folder.
FOLDER LIST
SUMMER 2003
NEW YEAR'S DAY
MY FAVOURITES
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
2
3
Press X/x to select the folder you want
to play.
DivX video files that the system
can play
Press H.
The system starts playing the selected
folder.
The system can play data that is recorded in
DivX format, and which has the extension
“.AVI,” or “.DIVX.” The system will not play
To select DivX video files, see “Selecting a
GB
46
Download from Www.Somanuals.com. All Manuals Search And Download.
To go to the next or previous
page
Tip
• If the number of viewing times is preset, you can play
the DivX video files as many times as the preset
number. The following occurrences are counted:
Press
/
.
– when the system is turned off.
– when another file is played.
– when the disc tray is opened.
To turn off the display
Press DVD MENU repeatedly.
To stop playback
Press x.
Selecting a DivX video file
1
press
.
The list of files in the folder appears.
FILE LIST
MY FAVOURITES
HAWAII 2004
VENUS
2
Press X/x to select a file and press
.
The selected file starts playing.
To go to the next or previous
page
Press
/
.
To return to the previous display
Press O RETURN.
To stop playback
Press x.
To play the next or previous DivX
video file without turning on the
above file list
You can select the next or previous DivX video
file in the same folder by pressing >/..
You can also select the first file of the next
folder by pressing > during playback of the
last file of the current folder. Note that you
cannot return to the previous folder by pressing
.. To return to the previous folder, select it
from the folder list.
GB
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Delay
Restricting Playback of
Between the Picture and the Disc
Sound
[PARENTAL CONTROL]
[A/V SYNC]
Playback of some DVD VIDEOs can be limited
according to a predetermined level such as the
age of the users. Scenes may be blocked or
replaced with different scenes.
You can set the playback restriction by
registering a password. When you set the
[PARENTAL CONTROL] function to on, you
need to enter the password to play restricted
discs.
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
1
2
3
Press
DISPLAY.
The Control Menu display appears on the
TV screen.
Press X/x to select
then press
[A/V SYNC],
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
.
The options for [A/V SYNC] appear.
Press X/x to select a setting.
2
Press
in stop mode.
DISPLAY while the system is
• [OFF]: Off.
• [ON]: You can adjust the difference
between picture and sound.
The Control Menu display appears on the
TV screen.
4
Press
.
3
4
5
6
Press X/x to select
then press
[SETUP],
Note
.
• Depending on the input stream, [A/V SYNC] may not
be effective.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
Press X/x to select [SYSTEM SETUP],
then press
.
The options for [SYSTEM SETUP] appear.
Press X/x to select [PARENTAL
CONTROL t], then press
.
x If you have not entered a password
The display for registering a new password
appears.
PARENTAL CONTROL
Enter a new 4-digit password,
ENTER
then press
.
GB
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter a 4-digit password using the number
buttons, then press
To turn off the [PARENTAL
CONTROL] function
.
The display for confirming the password
appears.
Set [LEVEL] to [OFF] in Step 11.
To play a disc for which
[PARENTAL CONTROL] is set
x When you have already registered a
password
The display for entering the password
appears.
1
Load the disc and press H.
The display for entering your password
appears.
7
Enter or re-enter your 4-digit password
using the number buttons, then press
.
2
Enter your 4-digit password using the
number buttons, then press
.
The display for setting the playback
limitation level appears.
The system starts playback.
Note
• When you play discs which do not have the
PARENTAL CONTROL
[PARENTAL CONTROL] function, playback
cannot be limited on this system.
LEVEL:
STANDARD:
CHANGE PASSWORD:
OFF
USA
• Depending on the disc, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the level.
If the Resume Play mode is canceled, the level returns
to the previous level.
Tip
8
9
Press X/x to select [STANDARD], then
press
• If you forget your password, remove the disc and
repeat Steps 1 to 7 of “Restricting Playback of the
Disc” (page 48). When you are asked to enter your
password, enter “199703” using the number buttons,
.
The selection items for [STANDARD] are
displayed.
then press
. The display will ask you to enter a new
Press X/x to select a geographic area
as the playback limitation level, then
4-digit password. After you enter a new 4-digit
password, replace the disc in the unit and press H.
When the display for entering your password appears,
enter your new password.
press
.
The area is selected.
When you select [OTHERS t], select and
enter a standard code in the table of
(page 105) using the number buttons.
Changing the password
10
11
Press X/x to select [LEVEL], then press
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
.
The selection items for [LEVEL] are
displayed.
2
Press
DISPLAY while the system is
in stop mode.
Press X/x to select the desired level,
then press
.
The Control Menu display appears on the
TV screen.
[PARENTAL CONTROL] setting is
complete.
3
4
Press X/x to select
then press
[SETUP],
The lower the value, the stricter the
limitation.
.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
GB
49
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Press X/x to select [SYSTEM SETUP],
then press
.
Using the Setup Display
You can make various adjustments of items such
as picture and sound.
Displayed items vary depending on the country
model.
The options for [SYSTEM SETUP] appear.
Press X/x to select [PARENTAL
CONTROL t], then press
.
The display for entering the password
appears.
Note
7
Enter your 4-digit password using the
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
number buttons, then press
.
8
Press X/x to select [CHANGE
PASSWORD t], then press
.
1
2
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
9
Enter your 4-digit password using the
number buttons, then press
.
10
11
Enter a new 4-digit password using the
number buttons, then press
Press
DISPLAY while the system is
.
in stop mode.
The Control Menu display appears on the
TV screen.
To confirm your password, re-enter it
using the number buttons, then press
.
3
4
5
Press X/x to select
then press
[SETUP],
.
If you make a mistake entering
your password
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
Press C before you press , then input the
correct number.
press
.
The Setup Display appears.
Press X/x to select the setup item, then
press
.
• [LANGUAGE SETUP] (page 51)
• [VIDEO SETUP] (page 51)
• [HDMI SETUP] (page 52)
• [AUDIO SETUP] (page 54)
• [SYSTEM SETUP] (page 54)
• [SPEAKER SETUP] (page 55)
Example: [VIDEO SETUP]
Selected item
VIDEO SETUP
TV TYPE:
LINE:
16:9
VIDEO
AUTO
PAUSE MODE:
Setup items
6
Press X/x to select an item, then press
.
GB
50
Download from Www.Somanuals.com. All Manuals Search And Download.
The options for the selected item appear.
Example: [TV TYPE]
x [OSD] (On-Screen Display)
You can switch the display language on the TV
screen.
VIDEO SETUP
TV TYPE:
LINE:
16:9
16:9
PAUSE MODE:
4:3 LETTER BOX
x [MENU] (DVD VIDEO only)
You can switch the language for the disc’s
menu.
4:3 PAN SCAN
Options
x [AUDIO] (DVD VIDEO only)
You can switch the language of the sound track.
When you select [ORIGINAL], the language
given priority in the disc is selected.
7
Press X/x to select a setting, then
press
.
The setting is selected and setup is
complete.
x [SUBTITLE] (DVD VIDEO only)
You can switch the language of the subtitle
recorded on the DVD VIDEO.
When you select [AUDIO FOLLOW], the
language for the subtitles changes according to
the language you selected for the sound track.
VIDEO SETUP
TV TYPE:
LINE:
4:3 LETTER BOX
VIDEO
PAUSE MODE:
AUTO
Selected setting
Note
• When you select a language in [MENU], [AUDIO],
or [SUBTITLE] that is not recorded on the DVD
VIDEO, one of the recorded languages will be
automatically selected (depending on the disc, the
language may not be selected automatically).
Note
• When you turn the system on after resetting and no
disc is in the unit, the guide message appears on the
press
. To return to normal screen, press CLEAR.
Tip
• If you select [OTHERS t] in [MENU], [AUDIO],
and [SUBTITLE], select and enter a language code
number buttons.
To reset all of the [SETUP]
settings
To reset all of the [SETUP] settings, see
Settings for the display
[VIDEO SETUP]
Setting the display or sound
track language
Select settings according to the TV to be
connected.
[LANGUAGE SETUP]
VIDEO SETUP
TV TYPE:
LINE:
16:9
VIDEO
AUTO
Set various languages for the on-screen display
or sound track.
PAUSE MODE:
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
MENU:
AUDIO:
SUBTITLE:
GB
51
Download from Www.Somanuals.com. All Manuals Search And Download.
x [TV TYPE]
You can select the aspect ratio of the connected
TV.
x [PAUSE MODE] (DVD VIDEO/DVD-R/
DVD-RW only)
You can select the picture in pause mode.
[AUTO]: The picture, including subjects that
move dynamically, is output with no jitter.
Normally select this position.
[16:9]: Select this when you connect a wide-
screen TV or a TV with a wide mode function.
[FRAME]: The picture, including subjects that
do not move dynamically, is output in high
resolution.
[4:3 LETTER BOX]: Select this when you
connect a 4:3 screen TV. Displays a wide picture
with bands on the upper and lower portions of
the TV screen.
Settings for the HDMI
[HDMI SETUP]
HDMI SETUP
HDMI RESOLUTION:
CONTROL FOR HDMI:
VOLUME LIMIT:
AUTO(1920x1080p)
OFF
LEVEL2
YCBCR
OFF
SD
YCB
C
R/RGB(HDMI):
AUDIO(HDMI):
[4:3 PAN SCAN]: Select this when you connect
a 4:3 screen TV. The system automatically
displays the wide picture on the entire screen
and cuts off the portions that do not fit.
JPEG RESOLUTION:
x [HDMI RESOLUTION]
You can select the type of video signal that is
output from the HDMI OUT jack. For details,
Note
• Depending on the DVD, [4:3 LETTER BOX] may be
selected automatically instead of [4:3 PAN SCAN] or
vice versa.
[AUTO (1920 × 1080p)]: The system outputs
the optimal video signal for the connected TV.
[1920 × 1080i]: The system outputs 1920 ×
1080i* video signals.
x [LINE]
[1280 × 720p]: The system outputs 1280 ×
720p* video signals.
[720 × 480p]**: The system outputs 720 ×
480p* video signals.
You can selects the output method for video
signals from the EURO AV T OUTPUT (TO
TV) jack on the rear panel of the unit.
[VIDEO]: The system outputs video signals.
[RGB]: The system outputs RGB signals.
* i: interlace, p: progressive
**Depending on the country model, [720 × 576p] may
appear.
Note
• If your TV does not accept RGB signals, no picture
appears on the TV screen even if you select [RGB].
Refer to the operating instructions supplied with your
TV.
x [CONTROL FOR HDMI]
You can set the [CONTROL FOR HDMI]
function to on/off. This function is available
when you connect the system and TV with an
HDMI cable. For details, see “Using the Control
• You cannot select [RGB] while the HDMI indicator
is lit. [RGB] automatically switches to [VIDEO]
when you turn on any connected HDMI equipment.
GB
52
Download from Www.Somanuals.com. All Manuals Search And Download.
[ON]: The system outputs audio signals by
converting Dolby Digital, DTS, or 96 kHz/24 bit
PCM signals to 48 kHz/16 bit PCM.
[OFF]: Off.
Note
[ON]: On. You can operate mutually between
components that are connected with an HDMI
cable.
• When you connect the unit and TV with an HDMI
cable and [ON] is selected, [AUDIO DRC], [A/V
SYNC], DYNAMIC BASS, “DEC. MODE,” and
sound mode are not applied to the sound that is output
from the TV.
Note
• When you set to [ON] without the HDMI connection
of the TV, [Please verify the HDMI connection.]
appears and you cannot set to [ON].
• When you set the function to other than “DVD,” the
system does not output the sound from the HDMI
OUT jack even if you set [AUDIO (HDMI)] to [ON].
x [VOLUME LIMIT]
x [JPEG RESOLUTION]
You can select the resolution of JPEG image
files output from the HDMI OUT jack.
If you change the output method of the TV to the
system speaker on the TV menu or by pressing
THEATRE, the System Audio Control
(page 64) is activated and loud sound may be
output depending on the volume level of the
system. You can prevent this by limiting the
maximum level of the volume.
[SD
]: The system outputs standard
resolution with a black frame.
[HD
]: The system outputs HD resolution
with a black frame.
[HD]: The system outputs the HD resolution
without a black frame.
[LEVEL3]: Maximum volume level is set to 10.
[LEVEL2]: Maximum volume level is set to 15.
[LEVEL1]: Maximum volume level is set to 20.
[OFF]: Off.
[(1920 × 1080i) HD
]: The system outputs
full size HD resolution with a black frame.
[(1920 × 1080i) HD]: The system outputs full
size HD resolution without a black frame.
Note
• This function is available only when [CONTROL
FOR HDMI] is set to [ON].
Note
• [JPEG RESOLUTION] is effective only when you
set [TV TYPE] in [VIDEO SETUP] to [16:9], and
you set [HDMI RESOLUTION] in [HDMI SETUP]
to other than [720 × 480p] or [720 × 576p].
x [YCBCR/RGB (HDMI)]
You can select the type of HDMI signal output
from HDMI OUT jack.
• You can select [(1920 × 1080i) HD
] or [(1920 ×
1080i) HD] only when you set [HDMI
[YCBC
R]: The system outputs YCB
C
R
signals.
RESOLUTION] in [HDMI SETUP] to [1920 ×
1080i].
[RGB]: The system outputs RGB signals.
• If you select [(1920 × 1080i) HD
1080i) HD], the next image appears after the black
screen.
] or [(1920 ×
Note
• If the playback picture becomes distorted, set
[YCBCR] to [RGB].
• HDMI signal will stop momentarily when:
– The system is loading or unloading a DATA CD or
DATA DVD disc.
• If the HDMI OUT jack is connected to a component
with a DVI jack, [RGB] signals will be automatically
output even when you select [YCBCR].
– You connect or remove a USB device.
x [AUDIO (HDMI)]
You can select the audio output status from the
HDMI OUT jack.
[OFF]: The system does not output the sound
from the HDMI OUT jack.
GB
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Settings for the audio
• [AUDIO DRC] works only for Dolby Digital.
[AUDIO SETUP]
x [TRACK SELECTION] (DVD VIDEO only)
You can give the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, DTS, Dolby Digital, or MPEG
audio) are recorded.
AUDIO SETUP
S-AIR SETUP:
SPEAKER FORMATION:
AUTO CALIBRATION:
AUDIO DRC:
OFF
OFF
TRACK SELECTION:
[OFF]: Off.
[AUTO]: The system selects the sound track
automatically according to the priority.
Note
x [S-AIR SETUP]
• When you set the item to [AUTO], the language may
change. The [TRACK SELECTION] setting has
higher priority than the [AUDIO] settings in
the disc, this function may not work.)
• If PCM, DTS, Dolby Digital sound, and MPEG audio
have the same number of channels, the system selects
PCM, DTS, Dolby Digital sound, and MPEG audio in
this order.
You can set up the S-AIR setting. For details,
[ID]
You can set the ID of the system.
[PAIRING]
You can pair the system and S-AIR sub unit,
such as surround amplifier or S-AIR receiver.
Note
• This function is available only when the S-AIR
transmitter (not supplied) is inserted into the unit.
Other Settings
[SYSTEM SETUP]
x [SPEAKER FORMATION]
You can select the position of the speakers for
the better surround sound. For details, see
SYSTEM SETUP
SCREEN SAVER:
BACKGROUND:
PARENTAL CONTROL:
DivX:
ON
JACKET PICTURE
Registration Code
MULTI-DISC RESUME:
RESET:
ON
x [AUTO CALIBRATION]
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
x [SCREEN SAVER]
You can reduce the display device damages
x [AUDIO DRC] (DVD VIDEO only)
You can compress the dynamic range of the
sound track. [AUDIO DRC] is useful for
watching movies at low volume late at night.
(ghosting). Press any button (e.g.,
cancel the screen saver.
H
button) to
[ON]: The screen saver image appears if you do
not operate the system for about 15 minutes.
[OFF]: Off.
[OFF]: No compression of dynamic range.
[STANDARD]: The system reproduces the
sound track with the kind of dynamic range that
the recording engineer intended.
[MAX]: The system compresses dynamic range
fully.
x [BACKGROUND]
You can select the background color or picture
on the TV screen.
GB
54
Download from Www.Somanuals.com. All Manuals Search And Download.
[JACKET PICTURE]: The jacket picture (still
picture) appears, but only when the jacket
picture is already recorded on the disc (CD-
EXTRA, etc.). If the disc does not contain a
jacket picture, the [GRAPHICS] picture
appears.
[GRAPHICS]: A preset picture stored in the
system appears.
[BLUE]: The background is blue.
[BLACK]: The background is black.
Note
• You cannot operate [SPEAKER SETUP] when you
connect headphones to the unit or surround amplifier.
SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT)
:
DISTANCE(SURROUND):
LEVEL(FRONT):
LEVEL(SURROUND):
TEFRONT:
CENTER:
SURROUND:
YES
YES
YES
YES
SUBWOOFER:
x [PARENTAL CONTROL]
You can set the playback restrictions. For
details, see “Restricting Playback of the Disc”
x [CONNECTION]
If you do not connect center or surround
speakers, set the parameters for [CENTER] and
[SURROUND]. Since the front speaker and
subwoofer setting is fixed, you cannot change
them.
x [DivX]
You can display the registration code for this
system.
[FRONT]
For more information, go to
http://www.divx.com on the Internet.
[YES]
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center speaker is used.
x [MULTI-DISC RESUME] (DVD VIDEO/
VIDEO CD only)
[SURROUND]
You can set the [MULTI-DISC RESUME]
function to on/off.
[YES]: Normally select this.
[NONE]: Select this if no surround speaker is
used.
[ON]: The system stores the resume points in
memory for up to 10 discs.
[OFF]: The system does not store the resume
points in memory. Playback restarts at the
resume point only for the current disc in the unit.
[SUBWOOFER]
[YES]
Note
• When you change the [CONNECTION] setting, the
[STANDARD] of [SPEAKER FORMATION]
setting remains the same, but the other settings of
[SPEAKER FORMATION] return to
[STANDARD].
x [RESET]
You can return the [SET UP] settings other than
[PARENTAL CONTROL] to the default
settings. For details, see “Returning the
x [DISTANCE (FRONT)]
When you move the front speakers and center
speaker, be sure to set the parameters of the
distance (A) from the listening position to the
speakers.
Settings for the speakers
[SPEAKER SETUP]
You can set the parameters from 1.0 to 7.0
1)
meters (3 to 23 ft) for the front speakers, from
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
2)
0.0 to 7.0 meters (0 to 23 ft) for the center
speaker.
GB
55
Download from Www.Somanuals.com. All Manuals Search And Download.
[L/R] 3.0 m/10 ft2)3): Set the surround speaker
distance (up to 5.0 meters (16 ft) closer to the
front speakers).
1)0.0 to 6.9 meters for North American models.
default settings are changed.
3)This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
A
Note
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
• Depending on the input stream, the [DISTANCE]
setting may not be effective.
[L/R] 3.0 m/10 ft3): Set the front speaker
distance.
[CENTER] 3.0 m/10 ft3)4): Set the center speaker
distance (up to 1.6 meters (5 ft) closer to the
front speakers).
x [LEVEL (FRONT)]
You can adjust the sound level of the front
speakers, center speaker, and subwoofer. Be
sure to set [TEST TONE] to [ON] for easy
adjustment.
1)0.9 to 6.9 meters for North American models.
2)0.0 to 6.9 meters for North American models.
default settings are changed.
4)This item appears when you set [CENTER] to [YES]
in the [CONNECTION] setting.
[L/R] 0.0 dB: Set the front speaker level.
[CENTER] 0.0 dB*: Set the center speaker
level.
[SUBWOOFER] +2.0 dB: Set the subwoofer
x [DISTANCE (SURROUND)]
level.
When you move the surround speakers, be sure
to set the parameters of the distance (B) from
the listening position to the speakers.
* This item appears when you set [CENTER] to
[YES] in the [CONNECTION] setting.
You can set the parameters from 0.0 to 7.0
meters (0 to 23 ft).
x [LEVEL (SURROUND)]
1)
You can adjust the sound level of the surround
speakers. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
[L/R] 0.0 dB*: Set the surround speaker level.
* This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
x [TEST TONE]
B
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
[OFF]: The test tone is not emitted from the
speakers.
[ON]: The test tone is emitted from each speaker
in sequence while adjusting level. When you
select one of the [SPEAKER SETUP] items, the
GB
56
Download from Www.Somanuals.com. All Manuals Search And Download.
test tone is emitted from each speaker in
sequence.
Adjust the sound level as follows.
1
2
Set the [TEST TONE] to [ON].
Press C/X/x/c repeatedly to select the
desired speaker and the level.
3
4
5
Press
.
Repeat Steps 1 to 3.
Press C/X/x/c repeatedly to set [TEST
TONE] to [OFF] after adjusting the
speaker level.
Note
• The test tone signals are not output from the HDMI
OUT jack.
Tip
• To adjust the volume of all the speakers at one time,
turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
• To return to the default setting when changing a
setting, select the item, then press CLEAR. Note that
only the [CONNECTION] setting does not return to
the default setting.
GB
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• You can select the preset number directly by
pressing the number buttons.
Tuner
7
Press
.
Presetting Radio
Stations
You can preset 20 FM stations, and 10 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
“COMPLETE” appears in the front panel
display, and the station is stored.
8
9
Repeat Steps 2 to 7 to store other
stations.
Press SYSTEM MENU.
The system menu turns off.
Tip
To change the preset number
• You can operate the tuner function by observing the
following display on the TV screen.
Restart from Step 2.
Current station
Current band and preset number
FM
FM 10 : 88.00 MHz
SONY RADIO
Station name
1
2
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Press and hold TUNING +/– until the
auto scanning starts.
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (for stereo
program) appear in the front panel display.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “MEMORY”
appears in the front panel display.
5
Press
or c.
A preset number appears in the front panel
display.
6
Press X/x to select the preset number
you want.
GB
58
Download from Www.Somanuals.com. All Manuals Search And Download.
If an FM program is noisy
Listening to the Radio
Preset radio stations in the system’s memory
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
1
2
Press SYSTEM MENU.
1
2
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
Press X/x repeatedly until “FM MODE”
appears in the front panel display.
The last received station is tuned in.
Press PRESET +/– repeatedly to select
the preset station.
3
4
Press
or c.
Each time you press the button, the system
tunes in one preset station.
Press X/x to select “MONO.”
• “STEREO”: Stereo reception.
• “MONO”: Monaural reception.
Tip
• You can select the preset station number directly
by pressing the number buttons.
5
6
Press
.
The setting is made.
3
Adjust the volume by pressing
VOLUME +/–.
Press SYSTEM MENU.
To turn off the radio
The system menu turns off.
Press "/1.
To listen to non-preset radio
stations
Naming preset stations
You can enter a name for preset stations. These
names (for example, “XYZ”) appear in the front
panel display when a station is selected.
Only one name can be entered for each preset
station.
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING +/–
repeatedly.
For automatic tuning, press and hold TUNING
+/–. The automatic tuning stops automatically
when the system receives the radio station. To
stop the automatic tuning manually, press
TUNING +/– or x.
Note
• You cannot enter a name for preset stations of the
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
To listen to radio stations when
you know the frequencies
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
The last received station is tuned in.
2
Press PRESET +/– repeatedly to select
the preset station you want to create an
index name for.
2
3
Press D.TUNING.
Press the number buttons to select the
frequencies.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “NAME IN”
appears in the front panel display.
4
Press
.
Tip
• To improve reception, reorient the connected
antennas (aerials).
5
Press
or c.
GB
59
Download from Www.Somanuals.com. All Manuals Search And Download.
When the station name is not set:
1 Frequency
Ex. “FM1 87.50”
6
Create a name by using C/X/x/c.
Press X/x to select a character, then press c
to move the cursor to the next position.
2 The “FM MODE” setting
Ex. “STEREO”
x “TUNER AM”
You can input letters, numbers, and other
symbols for a radio station.
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
If you make a mistake
Press C/c repeatedly until the character to
be changed flashes, then press X/x to select
the desired character.
Ex. “AM1 576”
When the station name is not set:
1 Frequency
Ex. “AM1 576”
To erase the character, press C/c
repeatedly until the character to be erased
flashes, then press CLEAR.
Note
7
8
Press
.
• The system returns to the original display when
several seconds has elapsed.
“COMPLETE” appears in the front panel
display, and the station name is stored.
Press SYSTEM MENU.
The system menu turns off.
Viewing the station name or
frequency in the front panel
display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency
using the front panel display.
Press DISPLAY.
Each time you press DISPLAY, the display
changes:
1 t 2 t .... t 1 t ....
x “TUNER FM”
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
Ex. “FM1 87.50”
3 The “FM MODE” setting
Ex. “STEREO”
GB
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Radio Data
System (RDS)
What is the Radio Data
System?
The Radio Data System (RDS) is a broadcasting
service that allows radio stations to send
additional information along with the regular
program signal. This tuner offers convenient
RDS features, such as station name display.
RDS is available only for FM stations.*
Note
• RDS may not work properly if the station you are
tuned to is not transmitting the RDS signal properly,
or if the signal strength is weak.
* Not all FM stations provide RDS service, nor do
they provide the same type of services. If you are not
familiar with the RDS system, check with your local
radio stations for details on RDS services in your
area.
Receiving RDS broadcasts
Simply select a station from the FM band.
When you tune in a station that provides RDS
services, the station name* appears in the front
panel display.
* If an RDS broadcast is not received, the station
name may not appear in the front panel display.
GB
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the connected component, the Control
for HDMI function may not work. Refer to the
operating instructions supplied with the component.
• The Control for HDMI function may not work if you
connect a component other than Sony, even if the
component is compatible with the Control for HDMI
function.
Control for HDMI/External Audio
Device
Using the Control for
HDMI Function for
“BRAVIA” Sync
Preparing for the Control for
HDMI function
This function is available on TVs with the
“BRAVIA” Sync function only.
(Control for HDMI - Easy Setting)
The system is compatible with the Control for
HDMI - Easy Setting function. If the TV is
compatible with the Control for HDMI - Easy
Setting function, you can set the system’s
[CONTROL FOR HDMI] function
By connecting Sony components that are
compatible with the Control for HDMI function
with an HDMI cable (not supplied), operation is
simplified as below:
automatically by setting the TV. For details,
refer to the operating instructions of the TV.
If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control
for HDMI function of the system and TV
manually.
Control for HDMI is a mutual control function
standard used by CEC (Consumer Electronics
Control) for HDMI (High-Definition
Multimedia Interface).
Note
• Displayed items vary depending on the country
model.
The Control for HDMI function will not work in
the following cases:
1
2
3
Make sure that the system and the TV
are connected with an HDMI cable.
– When you connect this system to a
component which is not compatible with the
Control for HDMI function.
Turn on the TV and press [/1 to turn on
the system.
– A component does not have an HDMI jack.
Switch the input selector on your TV so
that the signal from the system through
the HDMI input appears on the TV
screen.
There are convenient buttons on the system’s
remote for operating the TV, such as
THEATRE, ONE-TOUCH PLAY, TV [/1. For
details, see “Controlling the TV with the
Supplied Remote” (page 83) and refer to the
operating instructions of the TV.
4
Set the Control for HDMI function of the
system and TV.
For details of the setting of the system, see
the following Steps. For details of the
setting of the TV, refer to the operating
instructions of the TV (depending on the
TV, the default setting of the Control for
HDMI function is set to off).
ONE-TOUCH
PLAY
TV
THEATRE
BRAVIA Sync
GB
62
Download from Www.Somanuals.com. All Manuals Search And Download.
The One-Touch Play also works when:
To set the [CONTROL FOR HDMI]
function to on/off
– You press A while the disc tray is opened and
H appears in the front panel display.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
– You close the disc tray by pressing the disc
tray.
– You press DVD TOP MENU/DVD MENU
and H appears in the front panel display.
2
Press
in stop mode.
DISPLAY while the system is
– You select the “DVD” function by pressing
FUNCTION +/– and H appears in the front
panel display.
The Control Menu display appears on the
TV screen.
3
4
5
Press X/x to select
then press
[SETUP],
Note
.
• One-Touch Play does not work when you press H.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
The system and TV work as follows (e.g.):
press
.
The Setup Display appears.
This system
TV
Turns on. (If not already Turns on. (If not already
Press X/x to select [HDMI SETUP], then
turned on.)
turned on.)
press
.
r
r
The options for [HDMI SETUP] appear.
Switches to “DVD”
function.
Switches to HDMI input.
r
Minimizes sound level.
(System Audio Control)
6
7
Press X/x to select [CONTROL FOR
HDMI], then press
Press X/x to select the setting, then
press
.
r
Starts playing the disc and
outputs the sound.
.
• [OFF]: Off.
• [ON]: On.
Note
• Make sure the HDMI connection is correct, and set
the [CONTROL FOR HDMI] to [ON].
• Depending on the TV, the beginning of the content
may not be played back.
Note
• When [Please verify the HDMI connection.] appears,
make sure the HDMI connection is correct.
• Depending on the disc, playback may take a while to
start.
Using the Theatre Mode
(Theatre Mode)
Turning the system off in sync
with the TV
If your TV is compatible with the Theatre Mode,
you can enjoy optimal image suited for movies
and the sound is output from the system’s
speaker automatically by pressing THEATRE.
(System Power Off)
When you turn the TV off by using the POWER
button on the TV’s remote or TV [/1 on the
system’s remote, the system turns off
automatically.
Watching DVD by a single
button press
Note
• Before using the System Power Off function, set the
function for TV power. For details, refer to the
operating instructions of the TV.
(One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV
turns on, the TV is set for DVD input mode, and
the system starts playing a disc automatically.
• Depending on the status of the system (ex. while
other than “DVD” or “TV” function, or playing a
CD), the system may not turn off automatically.
GB
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Enjoying TV sound from the
speakers in this system
• You can connect the system and the TV audio
(System Audio Control)
You can enjoy TV sound in this system by easy
operation.
To use this function, connect the system and the
TV with an audio cord (not supplied) and an
Setting the Maximum Volume
Level of the System
(Volume Limit)
If you change the output method of the TV to the
system speaker on the TV menu or by pressing
THEATRE, loud sound may be output
depending on the volume level of the system.
You can prevent this by limiting the maximum
level of the volume. For details, see “[VOLUME
Depending on the TV, when you set the system
to the “TV” function, the System Audio Control
function is activated. TV sound is output from
the system speakers, and the volume of the TV
speakers is minimized automatically.
You can use the System Audio Control function
as follows:
• While you are watching the TV and the
function of the system is switched to “TV,” TV
sound is output from the system speakers
automatically.
• You can control the system’s volume by the
remote of the TV.
• If you turn the system off or set the function of
the system to other than “TV,” TV sound is
output from the TV speakers.
You can also operate the System Audio Control
function from the TV menu. For details, refer to
the operating instructions of the TV.
Note
• If the TV is turned on before turning on the system,
TV sound will not be output for a moment.
• While the TV is in PAP (picture and picture) mode,
the System Audio Control function will not work.
When the TV exits PAP mode, the output method of
the TV returns to the one before PAP mode.
• If you select a TV program during DVD playback
with the system, the “TV” function is automatically
set to output TV sound.
• When you activate One-Touch Play during watching
TV, the System Audio Control function is activated
and the TV sound is muted.
• While recording songs on an audio CD into a USB
device, the System Audio Control function will not
work.
GB
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• When you use the AUDIO IN/A.CAL MIC jack
while a USB device is connected, be careful as space
is restricted.
Playing Back Audio
Files/JPEG Image Files
of a USB Device
You can play audio files (MP3/WMA/AAC
files)/JPEG image files stored in a USB device
such as the digital music player or USB storage
media (not supplied) by connecting the USB
device to the unit.
1
Press FUNCTION +/– repeatedly until
“USB” appears in the front panel
display.
2
Connect a USB device (digital music
player or USB storage media) to the
(USB) port.
When you connect the USB device,
“READING” appears in the front panel
display until the system reads all data of the
USB device.
For a list of USB devices that can be connected
to the unit, see “Playable USB Devices”
(supplement).
The audio format that can be played back by the
system is MP3/WMA/AAC files* only.
* Files with copyright protection (Digital Rights
Management) cannot be played by the system.
Note
• When you connect the USB device, make sure that
the direction of the jack is correct.
• Do not forcibly insert the USB device, as this may
cause the device to be damaged.
Note
• Do not connect other device or objects besides the
USB device.
• The system cannot play WMA/AAC files on a DATA
CD/DATA DVD.
• It may take about 10 seconds before “READING”
appears in the front panel display depending on the
type of the USB device.
About playable USB devices
• Do not use USB devices other than those listed
in “Playable USB Devices” (supplement).
Operation of models not listed is not
guaranteed.
To remove the USB device
1
2
3
Press x to stop playback.
Press [/1 to turn off the system.
Remove the USB device.
• Operation is not guaranteed, even when using
these USB devices.
• Some of these USB devices may not be
available for purchase in certain areas.
Notes on the USB device
• The system can play back up to 200 folders,
including albums that do not contain audio
files and JPEG image files. When more than
200 folders are in the USB device, folders that
are recognized by the system differ depending
on the folder configuration.
Connecting the USB device
Front panel
• The system can play back the following files.
File
Extension of the file
“.mp3”
MP3 file
WMA file
AAC file
JPEG image file
“.wma”
“.m4a”
“.jpg” or “.jpeg”
The system will play back any data with the
extension above, even if it is not MP3/WMA/
AAC/JPEG format. Playing this data may
generate a loud noise which could damage
your speaker system.
USB device
GB
65
Download from Www.Somanuals.com. All Manuals Search And Download.
• The following USB devices/situations can
increase the time it takes to start playback:
Selecting an audio file or
folder
– a USB device recorded with a complicated
tree structure.
1
Press FUNCTION +/– repeatedly until
“USB” appears in the front panel
display.
– when the audio files or JPEG image files in
another folder have just been played back.
• Some USB devices cannot be played back on
the system depending on the file format.
• The system can play back to a depth of 8
folders only.
2
3
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
• The system may not be able to play an audio
file depending on the kind of file.
Press X/x to select
(MUSIC, IMAGE)], then press
[MODE
• When the USB device is inserted, the system
reads all the files on the USB device. If there
are many folders or files on the USB device, it
may take a long time to finish reading the USB
device.
.
The options for [MODE (MUSIC,
IMAGE)] appear.
4
5
6
Press X/x to select [MUSIC].
• Do not connect the system and the USB device
through a USB hub.
Press
.
Press DVD MENU.
• With some connected USB devices, after an
operation is performed, there may be a delay
before it is performed by this system.
• This system does not necessarily support all
the functions provided in a connected USB
device.
The folders recorded on the USB device
appear. When a folder is being played, its
title is shaded.
FOLDER LIST
01 Let's Talk About Love (1985)
02 1st Album (1986)
• Files recorded by a device such as a computer
may not be played back in the order in which
they were recorded.
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
• The playback order for the system may differ
from the playback order of the connected USB
device.
08 Alone (1999)
• Always turn off the system before removing
the USB device. Removing the USB device
while the system is on may corrupt the data on
the USB device.
7
Press X/x to select a folder.
x To play audio files in a folder
Press H to start playing the selected
folder.
• Do not save other types of files or unnecessary
folders on a USB device that has audio files or
JPEG image files.
x To select an audio file
Press
.
• Folders that have no audio files or JPEG image
files are skipped.
The list of files contained in the folder
appears.
• Compatibility with all MP3/WMA/AAC
encoding/writing softwares, recording
devices, and recording media cannot be
guaranteed. Incompatible USB device may
produce noise or interrupted audio or may not
play at all.
TRACK LIST
03 In the Middle of Nowher...
01_Geronimo_s_Cadillac
02_Riding_On_A_White_Swan
03_Give_Me_Peace_On_Earth
04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
06_Lonely_Tears_In_Chinatown
07_In_Shaire
• Before using the USB device, make sure that
no virus-ridden files are on the USB device.
GB
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Press X/x to select a file and press
.
The folders recorded on the USB device
appear. When a folder is being played, its
title is shaded.
The system starts playing the selected file.
You can turn the file list off by pressing
DVD MENU. Pressing DVD MENU again
will display the folder list.
FOLDER LIST
01 Let's Talk About Love (1985)
02 1st Album (1986)
Tip
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
• The system can recognize up to 150 audio files in a
single folder.
To stop playback
08 Alone (1999)
Press x.
To play the next or previous
audio file
7
Press X/x to select a folder.
x To play JPEG image files in a folder
as a slide show
Press H to start playing the selected
folder.
Press >/.. Note that you can select the
next folder by continuing to press > after the
last file on the current folder, but that you cannot
return to the previous folder by pressing ..
To return to the previous folder, select the folder
from the folder list.
The JPEG images are played as a slide
show. You can change the interval of the
To return to the previous display
x To select a JPEG image file by
displaying the subscreens
Press PICTURE NAVI.
Press O RETURN.
To turn off the display
Press DVD MENU.
Images of JPEG image files in the folder
appear in 16 subscreens.
Other operations
1
2
3
4
Selecting a JPEG image file or
folder
5
6
7
8
9
10
14
11
15
12
16
1
Press FUNCTION +/– repeatedly until
“USB” appears in the front panel
display.
13
Press C/X/x/c to select the JPEG image
file you want to view, then press
.
2
Press
in stop mode.
DISPLAY while the system is
To return to normal screen, press O
RETURN.
The Control Menu display appears on the
TV screen.
Tip
• A scroll box is displayed at the right side of the
TV screen. To display the additional JPEG
image files, select the bottom JPEG image file
and press x. To return to the previous JPEG
image file, select the top JPEG image file and
press X.
3
Press X/x to select
(MUSIC, IMAGE)], then press
[MODE
.
The options for [MODE (MUSIC,
IMAGE)] appear.
4
5
6
Press X/x to select [IMAGE].
• The system can recognize up to 150 JPEG
image files in a single folder.
Press
.
Press DVD MENU.
GB
67
Download from Www.Somanuals.com. All Manuals Search And Download.
To play the next or previous JPEG
image file
Note
• Some JPEG image files may take longer to display
than the option you selected. Especially progressive
JPEG image files or JPEG image files of 3,000,000
pixels or more.
Press c/C when the Control Menu display is not
displayed. Note that you can select the next
folder by continuing to press c after the last
image on the current folder, but that you cannot
return to the previous folder by pressing C. To
return to the previous folder, select the folder
from the folder list.
To select an effect for JPEG
image files in the slide show
1
2
3
Press
DISPLAY twice.
The Control Menu display appears on the
TV screen.
To rotate a JPEG image file
When a JPEG image file is displayed on the TV
screen, you can rotate the JPEG image file by 90
degrees.
Press X/x while viewing a JPEG image file.
Press CLEAR to return to normal view.
Press X/x to select
then press
[EFFECT],
.
The options for [EFFECT] appear.
Press X/x to select a setting.
• [MODE 1]: The JPEG image file sweeps
in from top to bottom.
Note
• You cannot rotate the JPEG image file when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
• [MODE 2]: The JPEG image file stretches
out from left to right of the TV screen.
• [MODE 3]: The JPEG image file stretches
out from the center of the TV screen.
• [MODE 4]: The JPEG image files
randomly cycle through the effects.
• [MODE 5]: The next JPEG image file
slides over the previous image.
× 1080i) HD
] or [(1920 × 1080i) HD].
To stop playback
Press x.
Other operations
• [OFF]: Off.
To select the slide show duration
of JPEG image files
4
Press
.
1
2
3
Press
DISPLAY twice.
Note
• The [EFFECT] setting is not effective when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
The Control Menu display appears on the
TV screen.
× 1080i) HD
Press X/x to select
then press
[INTERVAL],
.
The options for [INTERVAL] appear.
Displaying the list of audio
files/JPEG image files
Press X/x to select a setting.
• [NORMAL]: You can set the duration to
about 6 to 9 seconds.
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
• [FAST]: You can set the duration shorter
than [NORMAL].
• [SLOW 1]: You can set the duration
longer than [NORMAL].
Press X/x to select
[BROWSING], then press
.
• [SLOW 2]: You can set the duration
longer than [SLOW 1].
The options for [BROWSING] appear.
Press X/x to select the desired list,
then press
4
Press
.
.
• [FOLDER LIST]: The list of folders
appears. Follow Step 2 of “Selecting an
GB
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for an audio file/
JPEG image file/folder
• [PICTURE LIST]: Images of JPEG image
files in the folder appear in 16 subscreens.
Follow Step 2 of “Selecting a JPEG image
You can search a USB device by audio file,
JPEG image file, or folder. As audio files and
JPEG image files are assigned unique numbers
on the USB device, you can select the desired
audio file or JPEG image file by entering its
number.
Playing repeatedly
(Repeat Play)
1
Press
DISPLAY. (When playing a
You can play the audio files/JPEG image files
on the USB device repeatedly.
JPEG image files, press
twice.)
DISPLAY
The Control Menu display appears on the
TV screen.
1
2
3
Press
DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X/x to select the search method.
• [TRACK]: audio files.
Press X/x to select
then press
[REPEAT],
.
• [FILE]: JPEG image files.
• [FOLDER]: Folders.
The options for [REPEAT] appear.
Press X/x to select the item to be
repeated.
[** (**)] is selected (** refers to a number).
The number in parentheses indicates the
total number of audio files, JPEG image
files, or folders.
• [OFF]: Off.
• [MEMORY]: You can repeat all of the
folders on the USB device.
• [FOLDER]: You can repeat the current
folder.
1(
1( 144)
0: 23
1)
USB MUSIC
T
• [TRACK] (audio files only): You can
repeat the current file.
4
Press
.
The item is selected.
Selected row
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
3
4
Press
.
[** (**)] changes to [– – (**)].
To turn off the Control Menu
display
1(
1( 144)
1: 31
1)
USB MUSIC
Press
DISPLAY repeatedly until the Control
T
Menu display is turned off.
Note
• When [MODE (MUSIC, IMAGE)] is set to [IMAGE]
(page 67), you cannot select [TRACK].
Press X/x or the number buttons to
select the desired number.
If you make a mistake, press CLEAR to
cancel the number.
GB
69
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press
.
Bit rate
The system starts playback from the
selected number.
T
0: 13 192k MP3
Viewing the information of an
audio file in the front panel
display
2002_Remixes
Soul_Survivor_rap_version
Press DISPLAY repeatedly.
Each time you press DISPLAY while playing
the disc, the display changes:
1 y 2
Folder name*
File name*
* If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
1 Playing time and current track number
2 Track (file) name*
* If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
Note
• Characters/marks may not be displayed in some
languages.
• Depending on the type of file being played, the
system can only display a limited number of
characters. Also, depending on the file, not all text
characters will be displayed.
Note
• If a file name of the audio file cannot be displayed,
“*” will appear in the front panel display instead.
• The file name may not be displayed depending on the
text.
Checking the date information
of JPEG image file
• Playing time of MP3 files may not be displayed
correctly.
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image file.
Viewing the information of an
audio file on the TV screen
Press
DISPLAY twice during playback.
You can display the information of an audio file
such as time information, name of the folder/
audio file, and the audio bit rate (the amount of
data per second of the current audio) on the TV
screen.
The Control Menu display appears on the TV
screen.
2(
2)
6( 30)
USB IMAGE
16/9/2002
Press DISPLAY during playback.
Date information
The information of an audio file appears on the
TV screen.
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
GB
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• Date information is [DD/MM/YYYY].
DD: Day
MM: Month
YYYY: Year
Storing Songs in a USB
Device
You can record songs on an audio CD in a USB
device by encoding to MP3 format. You can also
copy the MP3 files on a DATA CD/DATA DVD
into the USB device.
For connecting the USB device, see
The recorded music is limited to private use
only. Use of the music beyond this limit requires
permission of the copyright holders.
Notes on the USB recording/
copying
• Do not connect the unit and the USB device
through an USB hub.
• Make sure there is enough space in the USB
device for recording or copying.
• Do not remove the USB device during
recording/copying.
• When you are recording tracks from a CD, the
tracks are recorded as 128 kbps MP3 files.
• When you are copying MP3 files from a
DATA CD/DATA DVD, the MP3 files are
recorded with the same bit rate as the original
MP3 files.
• CD text information is not recorded in the
created MP3 files.
• If you stop a recording partway, an MP3 file
whose recording was stopped halfway is
deleted.
• Recording stops automatically if:
– The USB device runs out of space during
recording/copying.
– The number of MP3 files on the USB
device reaches the limit for the number that
the system can recognize.
• You can store up to 150 files in a folder.
• You can store up to 199 folders in a single
USB device.
• If the folder to be erased contains non-audio
format files or sub folders, these are not erased.
• If a folder or file that you are trying to record
already exists on the USB device with the
same name, a sequential number is added after
GB
71
Download from Www.Somanuals.com. All Manuals Search And Download.
x To cancel all the track
Press C/X/x/c to select [s ALL], then
the name without overwriting the original
folder or file.
press
.
• Some USB devices cannot be played back on
the system depending on the file format.
6
Press C/X/x/c to select [START], then
press
.
The system starts recording and the status
of recording appears.
Recording songs on an audio
CD into a USB device
To cancel recording, press x.
1
2
Load an audio CD.
Copying MP3 files on a DATA
CD/DATA DVD into a USB device
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
1
2
Load a DATA CD/DATA DVD.
3
4
Press X/x to select
RECORDING], then press
[USB
.
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
Press X/x to select [TRACK], then
press
.
“READING” appears in the front panel
display until the tracks recorded on the
audio CD appear on the TV screen.
3
4
Press X/x to select
RECORDING], then press
[USB
.
Press X/x to select [TRACK] or
[FOLDER], then press
Note
.
• It takes several minutes to display the tracks
depending on the number of tracks.
• [TRACK]: The folders recorded on the
DATA CD/DATA DVD appear. You can
copy the desired MP3 file.
5
Select a track that you want to record.
• [FOLDER]: The folders recorded on the
DATA CD/DATA DVD appear. You can
copy all MP3 files in the folder. Go to
Step 6.
“READING” appears in the front panel
display until the tracks/folders appear on
the TV screen.
Recordable space of
the USB device
USB RECORDING
Free:
START
1
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
01
02
03
04
05
06
07
08
ALL
ALL
2
3
Note
• It takes several minutes to display the tracks/
folders depending on the number of tracks/
folders.
Tracks to be recorded.
5
6
Press X/x to select the desired folder,
x To select the desired track
Press X/x to select the track, then press
The tracks are marked in the order that you
select.
then press
.
.
The MP3 files in the selected folder appear.
Select a MP3 file/folder that you want to
copy.
x To select all tracks on the audio CD
Press C/X/x/c to select [x ALL], then
press
.
x To cancel the track
Press X/x to select the track, then press
The mark on the track is removed.
.
GB
72
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press X/x to select a folder.
Recordable space of
the USB device
x To erase all audio files in a folder
Press CLEAR.
USB RECORDING
2002_Remixes
Free:
x To erase an audio file
01_Back_Seat_O...
START
ALL
Press
.
02_One_Nights_...
03_Are_You_Ma...
04_I_Can_Lose_...
05_Soul_Survivo...
06_Strangers_B...
07_Stay_maxi_ve...
The list of files contained in the folder
appears.
ALL
Press X/x to select the desired audio file,
then press CLEAR.
3
Press C/c to select [YES], then press
MP3 files/folders to be copied.
.
To cancel, select [NO], then press
.
x To select the desired MP3 file/folder
Press X/x to select the MP3 file/folder, then
Note
• Do not remove the USB device while erasing.
press
.
• If the folder to be erased contains non-audio format
files or sub folders, these are erased from the list on
the TV screen, but are not erased from the USB
device.
The MP3 files/folders are marked.
x To select all MP3 files/folders
Press C/X/x/c to select [ ALL], then
press
.
To return to the previous display
x To cancel the MP3 file/folder
Press X/x to select the MP3 file/folder, then
Press O RETURN.
press
. The mark on the MP3 file/folder
is removed.
x To cancel all MP3 files/folder
Press C/X/x/c to select [ ALL], then
press
.
7
Press C/X/x/c to select [START], then
press
.
The system starts copying and the copying
status appears.
To cancel copying, press x.
To return to the previous display
Press O RETURN.
Note
• The audio file on a DATA CD/DATA DVD that you
can copy is the MP3 file only.
Erasing audio files on a USB
device
You can erase audio files on the USB device.
1
Press FUNCTION +/– repeatedly until
“USB” appears in the front panel
display.
GB
73
Download from Www.Somanuals.com. All Manuals Search And Download.
The sound and images from the connected
component are played on the system or
connected TV.
Using the DIGITAL MEDIA
PORT Adapter
The DIGITAL MEDIA PORT (DMPORT)
adapter (not supplied) is for enjoying sound
from a portable audio source or computer. By
connecting a DIGITAL MEDIA PORT adapter,
you can enjoy sound from the connected
component on the system.
Available DIGITAL MEDIA PORT adapters
vary in each area.
For details on connecting the DIGITAL MEDIA
PORT adapter, see “To connect the DIGITAL
For operation details, refer to the operating
instructions of the DIGITAL MEDIA
PORT adapter.
Tip
• When listening to MP3 files or other compressed
music using a portable audio source, you can enhance
the sound. Select “A.F.D. STD” for “DEC. MODE”
(page 30). To cancel, select other than “A.F.D. STD.”
• Depending on the type of DIGITAL MEDIA PORT
adapter, you may be able to operate a connected
component using either the buttons on the remote or
the unit. The following illustration shows an example
of buttons that can be used in this case.
Note
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is
turned on.
• Depending on the type of DIGITAL MEDIA PORT
adapter, the images are also output. In this case, the
system outputs the EURO AV OUTPUT signal only
regardless of the type of video signal.
• When you use the system and the Bluetooth Wireless
Audio Adapter (such as TDM-BT1, not supplied) at
the same time, transmission distance between the
Bluetooth transmitter and Bluetooth Wireless Audio
Adapter may be reduced. In this case, place the
Bluetooth transmitter as far as possible from the
system, or move the Bluetooth Wireless Audio
Adapter closer to the Bluetooth transmitter.
• When you use the system and the Wireless Network
Audio Adapter (such as TDM-NC1, not supplied) at
the same time, place the Wireless Network Audio
Adapter as far as possible from the system.
./>
H
x
X
Playing the connected
component on the system
1
2
Press FUNCTION +/– repeatedly until
“DMPORT” appears in the front panel
display.
Start playback of the connected
component.
GB
74
Download from Www.Somanuals.com. All Manuals Search And Download.
the unit and the wireless transceiver (not
supplied) into the S-AIR sub unit.
Using an S-AIR Product
Note
The unit is compatible with the S-AIR function
(page 103), which allows sound transmission
between S-AIR products.
When you purchase the S-AIR product, you
need to perform the following settings to
establish the sound transmission.
• When you insert the wireless transmitter/transceiver,
make sure that the AC power cord (mains lead) is not
connected to a wall outlet (mains).
• Do not touch the terminals of the wireless transmitter/
transceiver.
To insertthe wireless transmitter
into the unit
About S-AIR products
There are two types of S-AIR product.
• S-AIR main unit (this unit): This is for
transmitting sound. You can use up to three
S-AIR main unit. (The number of usable
S-AIR main unit depends on the use
environment.)
1
Remove the screws and detach the slot
cover.
Rear of the unit
ANTENNA
SPEAKER
FRONT SUR
FRONT
R
L
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
COAXIAL
OPTICAL
0.7A MAX
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
• S-AIR sub unit: This is for receiving sound.
– Surround amplifier: You can enjoy
surround speaker sound wirelessly.
Slot cover
0
0
1
-T
W
Z
E
– S-AIR receiver: You can enjoy system
sound in another room.
S-AIR sub unit
(S-AIR receiver)
Note
• Remove the screws from the slot cover bearing
the caution mark. Do not remove other screws.
• The slot cover is no longer necessary; however,
keep it after detaching.
S-AIR main unit
2
Insert the wireless transmitter.
Rear of the unit
ANTENNA
SPEAKER
FRONT SUR
FRONT
R
L
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
COAXIAL
OPTICAL
0.7A MAX
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
-T100
EZW
S-AIR sub unit
(surround amplifier)
Inserting the wireless
transmitter/transceiver
To make use of the S-AIR function, you need to
insert the wireless transmitter (not supplied) into
Note
• Insert the wireless transmitter with the S-AIR
logo facing up.
GB
75
Download from Www.Somanuals.com. All Manuals Search And Download.
• Insert the wireless transmitter so that the V
marks are aligned.
The system turns on.
2
3
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
• Do not insert other than the wireless transmitter
into the EZW-T100 slot.
3
Make sure to use the same screws to
secure the wireless transmitter.
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
Rear of the unit
ANTENNA
SPEAKER
FRONT SUR
FRONT
R
L
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
CENTER SUBWOOFER
DIGITAL IN
EURO AV
DC5V
COAXIAL
OPTICAL
0.7A MAX
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
4
5
6
7
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
-T100
EZW
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
Press X/x to select [AUDIO SETUP],
then press
.
The options for [AUDIO SETUP] appear.
Note
Press X/x to select [S-AIR SETUP t],
• Do not use other screws to fasten the wireless
transmitter.
then press
.
Note
• When the wireless transmitter is not inserted in
the unit, [S-AIR SETUP] cannot be selected.
To insert the wireless
transceiver into the S-AIR sub
unit
For details on installing the wireless transceiver
into the S-AIR sub unit, such as a surround
amplifier or S-AIR receiver, see the operating
instructions of the S-AIR sub unit.
8
9
Press X/x to select [ID], then press
.
Press X/x to select the desired ID, then
press
.
You can select any ID (A, B, or C).
The confirmation display appears.
10
Press
.
Establishing sound
transmission between the unit
and S-AIR sub unit
(ID setting)
Set the S-AIR sub unit to the same ID.
Sound transmission is established as
follows (example):
Other S-AIR main
unit
This unit
ID A
For the surround amplifier
For the S-AIR receiver
ID B
Simply by matching the ID of the unit and the
S-AIR sub unit, you can establish sound
transmission. You can use multiple S-AIR main
unit by setting a different ID for each
component.
ID A
S-AIR sub unit
ID B
S-AIR sub unit
ID A
S-AIR sub unit
To set the ID of the unit
1
Press "/1 on the unit.
GB
76
Download from Www.Somanuals.com. All Manuals Search And Download.
• When you pair the unit and another S-AIR sub
unit, such as a surround amplifier, by the pairing
operation, you need to perform the pairing
operation between the unit and the S-AIR
receiver. For details, see “Identifying the unit
Tip
• To confirm the current ID, perform Steps 1 to 7
above. When you pair the unit with the S-AIR sub
the display for selecting ID.
To set the ID of the surround
amplifier
Refer to the operating instructions of the
2
3
Press S-AIR MODE on the remote.
The S-AIR mode appears in the front panel
display. Each time you press S-AIR
MODE, the S-AIR mode changes.
• “PARTY”: The S-AIR receiver outputs
sound according to function set on the
unit.
surround amplifier.
To set the ID of the S-AIR
receiver
Refer to the operating instructions of the S-AIR
receiver.
• “SEPARATE”: You can set the desired
function for the S-AIR receiver while unit
functions do not change.
Note
• It is easy to set the same ID for the unit and S-AIR sub
unit to establish sound transmission. However,
neighbors may also receive your system’s sound if
IDs are the same, or you may receive the sound from
neighbors. To prevent this, you can identify the unit
with a specific S-AIR sub unit by performing the
Select the desired function on the
S-AIR receiver.
x When “PARTY” is set
The function changes in the same sequence
x When “SEPARATE” is set
The function changes as follows.
Enjoying the system’s sound in
another room
“MAIN UNIT” t “TUNER FM” t
“TUNER AM” t “DMPORT” t
“AUDIO” t …
For the S-AIR receiver
You can enjoy the system’s sound by using the
S-AIR receiver. The S-AIR receiver can be
installed anywhere, regardless of the location of
the unit, for enjoying the system’s sound in
another room.
To enjoy the same function as the unit,
select “MAIN UNIT.”
When “TUNER FM” or “TUNER AM” is
selected on the unit, you can only select the
same band for the tuner on the S-AIR
receiver. In this case, when you select other
than “TUNER FM” or “TUNER AM” on
the unit, you can select any band for the
tuner on the S-AIR receiver.
For details of the S-AIR receiver, refer to the
operating instructions of the S-AIR receiver.
1
Set the ID of the S-AIR receiver to that
of the unit.
• To set the ID of the unit, see “To set the ID
4
Adjust the volume on the S-AIR
receiver.
• To set the ID of the S-AIR receiver, refer
to the operating instructions of the S-AIR
receiver.
Note
• When the sound is other than 2 channel stereo, multi
channel sound is downmixed to 2 channel.
• The sound of the S-AIR receiver may be cut off by
operation of the unit.
Note
• When you are using another S-AIR sub unit,
such as a surround amplifier, do not change the
ID of the unit. Set the ID of the S-AIR receiver
to the same ID as the unit.
GB
77
Download from Www.Somanuals.com. All Manuals Search And Download.
transmission between the unit and S-AIR receiver is
established) in the front panel display.
To control the system from the
S-AIR receiver
You can control the system from the S-AIR
• If you turn the system off with the disc tray opened
while “S-AIR STBY” is set to “ON,” the disc tray
may not close automatically.
receiver by using the following buttons.
• When the wireless transmitter is not inserted in the
unit, you cannot set “S-AIR STBY.”
Press
Operation
• “S-AIR STBY” is set to “OFF” automatically when
the wireless transmitter is removed from the unit.
H, X, x,
./>
Share the same operations on the
remote and unit.
S-AIR CH
Change the function of the system.
Identifying the unit with a
specific S-AIR sub unit
(Pairing operation)
For the surround amplifier
For the S-AIR receiver
For details, refer to the operating instructions of
the S-AIR receiver.
Enjoying the S-AIR receiver
while the unit is in standby
mode
It is easy to set the same ID for the unit and an
S-AIR sub unit, such as a surround amplifier or
S-AIR receiver, to establish sound transmission.
However, neighbors may also receive your
system’s sound if IDs are the same, or you may
receive the sound from neighbors. To prevent
this, you can identify the unit with a specific
S-AIR sub unit by performing the pairing
operation.
For the S-AIR receiver
You can enjoy the S-AIR receiver while the unit
is in standby mode by setting “S-AIR STBY” to
“ON.”
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “S-AIR
STBY” appears in the front panel
When you perform pairing
Before pairing, sound transmission is
established by the ID (example).
display, then press
or c.
3
Press X/x to select the desired setting.
• “ON”: You can enjoy the S-AIR receiver
while the unit is in standby mode or turned
on.
Your room
This unit
Neighbor
• “OFF”: You cannot enjoy the S-AIR
receiver while the unit is in standby mode.
The default setting differs depending on the
model.
ID A
4
Press
.
The setting is made.
ID A
ID A
S-AIR sub unit
5
Press SYSTEM MENU.
S-AIR sub unit
The system menu turns off.
Note
• When you set “S-AIR STBY” to “ON,” the power
consumption during the standby mode increases.
• When you turn the system off while “S-AIR STBY”
is set to “ON,” “S-AIR” flashes (when sound
transmission between the unit and S-AIR receiver is
not established), or lights up (when sound
After pairing, sound transmission is established
between the paired unit and S-AIR sub unit(s)
only.
GB
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Your room
This unit
Neighbor
• When the wireless transmitter is not inserted in
the unit, [S-AIR SETUP] cannot be selected.
ID A
9
Press X/x to select [PAIRING], then
press
.
No transmission
The confirmation display appears.
10
Press C/c to select [YES], then press
.
The unit starts pairing.
ID A
ID A
To not perform pairing, select [NO].
S-AIR sub unit
S-AIR sub unit
11
Start pairing of the S-AIR sub unit.
x For the surround amplifier
Refer to the operating instructions of the
surround amplifier.
Pairing
1
Place the S-AIR sub unit that you want
to pair near the unit.
When sound transmission is established,
the confirmation display appears.
Note
x For the S-AIR receiver
Refer to the operating instructions of the
S-AIR receiver.
• Remove headphones from the surround
amplifier (if connected).
2
Match the IDs of the unit and the S-AIR
sub unit.
When sound transmission is established,
the confirmation display appears.
• To set the ID of the unit, see “To set the ID
• To set the ID of the S-AIR sub unit, refer
to the operating instructions of the S-AIR
sub unit.
Note
• Perform the pairing within several minutes after
Step 10. If you do not, the pairing is canceled
automatically and the confirmation display
appears. To perform pairing, select [YES]. To
return to the previous display, select [NO].
3
4
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
12
Press C/c to select the next operation.
x To finish pairing
Press
in stop mode.
DISPLAY while the system is
Select [NO], then press
.
x To perform pairing of another S-AIR
sub unit
Select [YES], then press
The Control Menu display appears on the
TV screen.
.
5
6
7
8
Press X/x to select
then press
[SETUP],
Note
.
• If you perform the pairing operation between the unit
transmission established by ID is canceled.
• When you perform pairing, [(PAIRING)] appears
beside ID on the display for selecting ID.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
To cancel pairing
Press X/x to select [AUDIO SETUP],
Perform the ID setting of the unit according to
you select a new ID (you can select the same ID
as before), pairing is canceled.
then press
.
The options for [AUDIO SETUP] appear.
Press X/x to select [S-AIR SETUP t],
then press
.
GB
79
Download from Www.Somanuals.com. All Manuals Search And Download.
– S-AIR ID C: equivalent channel for Wi-Fi
channel 11
If sound transmission is
unstable
For the surround amplifier
For the S-AIR receiver
• The transmission may be improved by changing the
transmission channel (frequency) of the other
wireless system(s). For details, refer to the operating
instructions of the other wireless system(s).
If you use multiple wireless systems which
sharing the 2.4 GHz band, such as wireless LAN
or Bluetooth, the transmission of S-AIR
products or other wireless systems may be
unstable. In this case, the transmission may be
improved by changing the following “RF
CHANGE” setting.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “RF
CHANGE” appears in the front panel
display, then press
or c.
3
Press X/x to select the desired setting.
• “AUTO”: Normally select this. The
system change “RF CHANGE” to “ON”
or “OFF” automatically.
• “ON”: The system transmits sound by
searching the better channel for
transmitting.
• “OFF”: The system transmits sound by
fixing the channel for transmitting.
4
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
When you set “RF CHANGE” to “OFF,”
select the ID so that sound
transmission is most stabilized
Note
• When the wireless transmitter is not inserted in the
unit, you cannot set “RF CHANGE.”
• In most cases, you will not need to change this
setting.
• If “RF CHANGE” is set to “OFF,” transmission
between the unit and S-AIR sub unit can be
performed using one of the following channels.
– S-AIR ID A: equivalent channel for Wi-Fi
channel 1
– S-AIR ID B: equivalent channel for Wi-Fi
channel 6
GB
80
Download from Www.Somanuals.com. All Manuals Search And Download.
• [NO CENTER]: Select this when you
install the front and surround speakers
only.
Other Operations
• [NO SURROUND]: Select this when you
install the center and front speakers only.
• [FRONT ONLY]: Select this when you
install the front speakers only.
• [ALL FRONT]: Select this when you
install all the speakers in front of the
listening position.
Getting Optimal
Surround Sound for a
Room
[SPEAKER FORMATION]
• [ALL FRONT - NO CENTER]: Select
this when you install the front and
surround speakers in front of the listening
position.
Depending on the shape of the room, you cannot
install some speakers. For the better surround
sound, Sony recommends that first you decide
the position of the speakers.
8
9
Press
.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
The setting is made and the confirmation
display appears.
Press C/c to select [YES] or [NO], then
press
2
Press
DISPLAY while the system is
.
in stop mode.
• [YES]: Continue with [AUTO
CALIBRATION]. Follow the procedure
from Step 7 of “Calibrating the
The Control Menu display appears on the
TV screen.
3
4
5
6
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
• [NO]: Exit [SPEAKER FORMATION].
Press X/x to select [CUSTOM], then
Note
press
.
• In order to enjoy the surround sound after you change
the position of the speakers, Sony recommends you
set [SPEAKER FORMATION], and then set [AUTO
The Setup Display appears.
Press X/x to select [AUDIO SETUP],
then press
.
• When you change the [CONNECTION] setting in
FORMATION] setting returns to [STANDARD].
The options for [AUDIO SETUP] appear.
Press X/x to select [SPEAKER
FORMATION], then press
.
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
STANDARD
7
Press C/c to select a setting.
• [STANDARD]: Select this when you
install all the speakers normally.
GB
81
Download from Www.Somanuals.com. All Manuals Search And Download.
obstruction between the speakers and the
calibration mic.
Calibrating the
Appropriate Settings
Automatically
[AUTO CALIBRATION]
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
Note
• The system outputs a loud test sound when [AUTO
CALIBRATION] starts. You cannot turn the volume
down. Give consideration to children and neighbors.
• Make sure that the headphones are not connected to
the unit or surround amplifier. You cannot operate the
following Steps with the headphones connected.
Calibration mic
1
2
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
Press
DISPLAY while the system is
in stop mode.
The Control Menu display appears on the
TV screen.
3
4
5
6
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
8
9
Press C/c to select [YES].
Press X/x to select [CUSTOM], then
Press
.
press
.
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
The Setup Display appears.
Press X/x to select [AUDIO SETUP],
then press
.
Note
• Before [AUTO CALIBRATION], make sure
that the surround amplifier turns on and you
install the surround amplifier in the appropriate
location. If you install the surround amplifier in
an improper location, such as another room,
proper measurement will not be obtained.
• Avoid being in the measurement area and
making noise during the measurement (about 3
minute), to avoid measurement failure. During
the measurement, test signals are output from
the speakers.
The options for [AUDIO SETUP] appear.
Press X/x to select [AUTO
CALIBRATION], then press
.
The options for [AUTO CALIBRATION]
appear.
7
Connect the calibration mic (supplied)
to the A.CAL MIC jack on the front
panel
Set up the calibration mic at the ear level
using a tripod, etc. (not supplied).
• The environment of the room in which the
system is installed may affect measurements.
• If an error message appears, follow the message,
then select [YES].
The front of each speaker should face the
calibration mic, and there should be no
An error message appears when:
GB
82
Download from Www.Somanuals.com. All Manuals Search And Download.
– the headphones are connected to the unit or
surround amplifier.
Controlling the TV with
the Supplied Remote
You can control the TV (Sony only) by using
following buttons. Use these buttons (other than
TV [/1, THEATRE, TV INPUT, and TV VOL
+/–) while pressing the TV button.
– the calibration mic is not connected.
– front speakers are not correctly connected.
– surround speakers are not correctly
connected.
– front and surround speakers are not correctly
connected.
10
Press C/c to select [YES] or [NO], then
press
.
Note
• Depending on the TV, you may not be able to control
your TV or to use some of the buttons.
x The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
By pressing
TV [/1
You can
x The measurement is not OK.
Follow the message, then select [YES] to
retry.
Turn the TV on/off.
Enjoy optimal image suited for
movies.
THEATRE
Note
TV INPUT
Switch the TV’s input source
between the TV and other input
sources.
• While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
TV VOL +/–
PROG +/–*
Adjust the TV volume.
Select the TV channel.
Select the TV channel.
– do not change the volume.
– do not change the function.
Number
buttons*, -*
ENTER*
– do not change the disc.
– do not insert or eject a disc.
– do not connect the headphones to the unit or
surround amplifier.
TOOLS*
Displays the operation menu for
the current display.
– do not disconnect the calibration mic.
• The measurement for [SUBWOOFER] is always
[YES] since the system does not perform subwoofer
calibration.
RETURN*
Return to the previous channel or
layer on the menu of the TV.
MENU*
Display the menu of the TV.
MUTING*
Turn off the TV sound
temporarily.
Tip
• You can check the distance between the listening
position and each speaker. See page 55.
C/X/x/c*,
*
Select the item on the menu.
* Use these buttons while pressing the TV button.
GB
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sound Effect
Using the Sleep Timer
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minutes
increments.
Reinforcing bass frequencies
You can reinforce bass frequencies.
Press DYNAMIC BASS.
Press SLEEP.
“D. BASS ON” appears in the front panel
display and bass frequencies are effectively
reinforced.
Each time you press SLEEP, the minutes display
(the remaining time) changes by 10-minutes.
When you set the sleep timer, “SLEEP” flashes
in the front panel display.
To turn off the sound effect
To check the remaining time
Press DYNAMIC BASS again.
Press SLEEP once.
To change the remaining time
Enjoying the sound at low
volume
Press SLEEP repeatedly to select the desired
time.
You can enjoy sound effects or dialogue, as you
would in a movie theater, even at low volume. It
is useful for watching movies at night.
To cancel the sleep timer
function
Press SLEEP repeatedly until “SLEEP OFF”
appears in the front panel display.
Press NIGHT.
“NIGHT ON” appears in the front panel display
and the sound effect is activated.
To set the sleep timer using the
system menu
Note
1
2
Press SYSTEM MENU.
• This effect does not work for a Super Audio CD.
When you load a Super Audio CD during “NIGHT
ON,” the sound effect turns off automatically.
• When sound is output from the center speaker, this
effect is more pronounced, as speech (movie dialog,
etc.) is easy to hear. When sound is not output from
the center speaker, or you are using the headphones,
the system optimally adjusts the volume.
Press X/x repeatedly until “SLEEP”
appears in the front panel display, then
press
or c.
3
Press X/x to select a setting.
The minutes display (the remaining time)
changes in 10-minutes.
To turn off the sound effect
Tip
Press NIGHT again.
• You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
4
5
Press
.
The setting is made and “SLEEP” flashes in
the front panel display.
Press SYSTEM MENU.
The system menu turns off.
GB
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Brightness Viewing Information
of the Front Panel
About the Disc
Display
The brightness of the front panel display can be
set to either of 2 levels.
Viewing the playing time and
remaining time in the front
panel display
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press
or c.
Press DISPLAY repeatedly.
3
Press X/x to select the brightness of
the front panel display.
Each time you press DISPLAY while playing
the disc, the display changes:
1 t 2 t ... t 1 t ...
• “DIMMER OFF”: Bright.
• “DIMMER ON”: Dark.
Some displayed items may disappear after a few
4
5
Press
.
seconds.
The setting is made.
x DVD VIDEO/DVD-VR
1 Playing time of the current title
2 Remaining time of the current title
3 Playing time of the current chapter
4 Remaining time of the current chapter
5 Disc name
Press SYSTEM MENU.
The system menu turns off.
6 Title and chapter
x VIDEO CD (without PBC functions)/
Super Audio CD/CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Track name
6 Track and index*
* VIDEO CD/Super Audio CD only.
x Super VCD
1 Playing time of the current track
2 Track text
3 Track and index number
x DATA CD (MP3 file)/DATA DVD (MP3 file)
1 Playing time and current track number
2 Track (file) name*
* If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
GB
85
Download from Www.Somanuals.com. All Manuals Search And Download.
x DATA CD (DivX video file)/DATA DVD
(DivX video file)
x VIDEO CD (without PBC functions)/
Super Audio CD/CD
1 Playing time of the current file
2 Current file name
• T **:**
Playing time of the current track
3 Current album and file number
• T-**:**
Remaining time of the current track
Note
• D **:**
Playing time of the current disc
• D-**:**
• The system can only display the first level of the
DVD/CD text, such as the disc name or title.
• If a file name of the MP3 file cannot be displayed, “*”
will appear in the front panel display instead.
• The disc name or track name may not be displayed
depending on the text.
Remaining time of the current disc
x DATA CD (MP3 file)/DATA DVD (MP3
file)
• Playing time of MP3 files and DivX video files may
not be displayed correctly.
• T **:**
Playing time of the current track
Tip
x DATA CD (DivX video file)/DATA
DVD (DivX video file)
• When the system is playing a VIDEO CD with PBC
functions, the playing time is displayed.
• **:**:**
Playing time of the current file
Viewing the playing time and
remaining time on the TV
screen
Note
• Characters/marks may not be displayed in some
languages.
• Depending on the type of disc being played, the
system can only display a limited number of
characters. Also, depending on the disc, not all text
characters will be displayed.
1
Press DISPLAY during playback.
The following display appears on the TV
screen.
Checking the play information
of the disc
T
1: 01: 40
Time information
To check DVD/Super Audio CD/CD
text
2
Press DISPLAY repeatedly to change
the time information.
Press DISPLAY repeatedly during playback to
display text recorded in the DVD/Super Audio
CD/CD.
The DVD/Super Audio CD/CD text appears
only when text is recorded in the disc. You
cannot change the text. If the disc does not
contain text, “NO TEXT” appears.
The display and the kinds of time that you
can check depend on the disc you are
playing.
x DVD VIDEO/DVD-VR
• T **:**:**
Playing time of the current title
• T-**:**:**
Remaining time of the current title
• C **:**:**
Playing time of the current chapter
• C-**:**:**
Dvorak/Tchaikovsky /NedPho/Kreizberg
Adagio - Allegro molto
Remaining time of the current chapter
x VIDEO CD (with PBC functions)
• **:**
Playing time of the current scene
GB
86
Download from Www.Somanuals.com. All Manuals Search And Download.
To check DATA CD/DATA DVD
(MP3 file/DivX video file) text
5(
8)
10( 15)
DATA CD JPEG
18/9/2002
By pressing DISPLAY while playing MP3 files
or DivX video files on a DATA CD/DATA
DVD, you can display the name of the folder/
MP3 file/DivX video file, and the audio bit rate
(the amount of data per second of the current
audio) on the TV screen.
Date information
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
Bit rate*
T
0: 13 192k MP3
Tip
• Date information is [DD/MM/YYYY].
DD: Day
MM: Month
YYYY: Year
2002_Remixes
Soul_Survivor_rap_version
Folder name**
MP3 File**/DivX video file
name
* Appears when:
– playing an MP3 file on a DATA CD/DATA DVD.
– playing a DivX video file that contains MP3 audio
signals on a DATA CD/DATA DVD.
**If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
Checking the date information
of JPEG image file
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image file.
Press
DISPLAY twice during playback.
The Control Menu display appears on the TV
screen.
GB
87
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select [SYSTEM SETUP],
then press
.
Returning to the Default
Settings
The options for [SYSTEM SETUP] appear.
Press X/x to [RESET] and press c.
Press C/c to select [YES].
6
7
Returning the system
parameters, such as preset
stations, to the default
settings
You can also quit the process and return to
the Control Menu display by selecting [NO]
here.
8
Press
.
Do not press [/1 while resetting the system
as it takes a few seconds to complete.
A
x
"/1
Note
• The [MODE (MUSIC, IMAGE)], [INTERVAL],
[EFFECT], and [MULTI/2CH] settings are also
return to the default settings.
1
2
Press "/1 to turn on the system.
Press x, A, and "/1 on the unit at the
same time.
“COLD RESET” appears in the front panel
display and the system returns to default
settings.
Returning the [SETUP] settings
to the default
You can return the [SETUP] settings (page 50)
other than [PARENTAL CONTROL] to the
default settings.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears on the
TV screen.
3
4
Press X/x to select
then press
[SETUP],
.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
GB
88
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
Additional Information
Precautions
On power sources
• Unplug the unit from the wall outlet (mains) if you do
not intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
On cleaning
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On placement
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the unit in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the unit can overheat and malfunction.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
• Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation slots.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
• Do not install the unit near heat sources such as
radiators, or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
• Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the unit and discs away from components with
strong magnets, such as microwave ovens, or large
loudspeakers.
On moving the system
Before moving the system, make sure that there is no
disc inserted, and remove the AC power cord (mains
lead) from the wall outlet (mains).
• Do not place heavy objects on the unit.
On operation
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the control unit.
Should this occur, the system may not operate
properly. In this case, remove the disc and leave the
system turned on for about half an hour until the
moisture evaporates.
• When you move the system, take out any disc. If you
don’t, the disc may be damaged.
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
GB
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
This system can only play back a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
GB
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your
nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
When you install the S-AIR sub unit (not supplied), in the event of a problem with the S-AIR function,
have a Sony dealer check the entire system together (main unit and S-AIR sub unit).
Power
Symptom
Remedy
The power is not turned on.
• Check that the AC power cord (mains lead) is connected securely.
• Press "/1 after “STANDBY” disappears from the front panel display.
If “PROTECTOR” and “PUSH Press "/1 to turn off the system, and check the following items after
POWER” appear alternately in “STANDBY” disappears.
the front panel display.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If
the cause of the problem cannot be found even after checking all the above
items, consult your nearest Sony dealer.
Picture
Symptom
Remedy
There is no picture.
• The SCART (EURO AV) cord is not connected securely.
• The SCART (EURO AV) cord is damaged.
• The video input on the TV is not set so that you can view pictures from the
system.
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
• If the HDMI OUT jack is used for video output, changing the type of video
Connect the TV and the unit using a video jack other than the HDMI OUT, and
switch the TV’s input to the connected video input so that you can see the on-
screen displays. Change the type of video signal output from the HDMI OUT
jack, and switch the TV’s input back to HDMI. If the picture still does not
appear, repeat the Steps and try other options.
Picture noise appears.
• The disc is dirty or flawed.
• If the signal from the EURO AV T OUTPUT (TO TV) jack is distorted,
change the type of video signal output from the HDMI OUT jack by setting
* Depending on the country model, [720 × 576p] may appear.
GB
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
Even though you set the aspect • The aspect ratio on the disc is fixed.
ratio in [TV TYPE] of [VIDEO
SETUP], the picture does not fill
the TV screen.
Color irregularity occurs on the The subwoofer and the front speakers in this system are magnetically shielded to
TV screen.
prevent magnetic leakage. However, some leakage may occur, as a high-strength
magnet is employed. If this happens, check the following items:
• If the speakers are used with a CRT-based TV or projector, install the speakers
at least 0.3 meters (1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15
to 30 minutes.
• If howling occurs, reposition the speakers farther away from the TV set.
• Make sure that no magnetic object (magnetic latch on a TV stand, health care
device, toy, etc.) is placed near the speakers.
Sound
Symptom
Remedy
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON” is displayed in the front panel
display.
• The system is in pause mode or in Slow-motion Play mode. Press H to return
to normal play mode.
• Fast forward or fast reverse is performed. Press H to return to normal play
mode.
• Super Audio CD audio signals are not output from the HDMI OUT jack.
• The component connected to the HDMI OUT jack does not conform to the
audio signal format, in this case set [AUDIO (HDMI)] in [HDMI SETUP] to
No sound is output from the
HDMI OUT jack.
• The HDMI OUT jack is connected to a DVI (Digital Visual Interface) device
(DVI (Digital Visual Interface) jacks do not accept audio signals).
• The HDMI OUT jack does not output Super Audio CD sound.
• Try the following: 1 Turn the system off and on again. 2 Turn the connected
component off and on again. 3 Disconnect and then connect the HDMI cable
again.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components are connected correctly and securely.
There is no sound from the
subwoofer.
Severe hum or noise is heard.
• Check that the speakers and components are connected securely.
• Check that the connecting cords are away from a transformer or motor, and at
least 3 meters (10 ft) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The sound loses stereo effect
when you play a VIDEO CD, a
CD, or an MP3 file.
• Set [AUDIO] to [STEREO] by pressing AUDIO (page 35).
• Make sure the unit is connected properly.
GB
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
hear when you are playing a
sound track of Dolby Digital,
DTS, or MPEG audio.
• Depending on the DVD, the output signal may not be the entire 5.1 channel. It
may be monaural or stereo even if the sound track is recorded in Dolby Digital
or MPEG audio format.
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.
speaker only.
No sound is heard from the
center speaker.
• Depending on the source, the effect of the center speaker may be less
noticeable.
• A 2 channel source is being played.
No sound or only a very low-
level sound is heard from the
surround speakers.
• Depending on the source, the effect of the surround speakers may be less
noticeable.
• A 2 channel source is being played.
There is no sound from the
DIGITAL IN COAXIAL/
OPTICAL jack.
• The sampling frequency of the input signal is more than 48 kHz.
Operation
Symptom
Remedy
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna
in.
(aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic
tuning). Use direct tuning.
• No stations have been preset or the preset stations have been cleared (when
• Press DISPLAY so that the frequency appears in the front panel display.
Noise is heard on AM radio.
The remote does not function.
• There are obstacles between the remote and the unit.
• The distance between the remote and the unit is too far.
• The remote is not pointed at the remote sensor on the unit.
• The batteries in the remote are weak.
The disc does not play.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 5).
• The region code on the DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
GB
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
The MP3 file cannot be played. • The DATA CD is not recorded in the MP3 format that conforms to ISO 9660
Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in an MP3 format that conforms to UDF
(Universal Disk Format).
• The MP3 file does not have the extension “.MP3.”
• The data is not formatted in MP3 even though it has the extension “.MP3.”
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO format.
• The [MODE (MUSIC, IMAGE)] setting has been set to [IMAGE] (page 44).
• If you cannot change the [MODE (MUSIC, IMAGE)] setting, re-load the disc
or turn the system off, then on.
• The DATA CD/DATA DVD contains a DivX video file.
The JPEG image file cannot be • The DATA CD is not recorded in a JPEG format that conforms to ISO 9660
played.
Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in a JPEG format that conforms to UDF
(Universal Disk Format).
• It has an extension other than “.JPEG” or “.JPG.”
• It is larger than 3,072 (width) × 2,048 (height) in normal mode, or more than
2,000,000 pixels in Progressive JPEG image file which is mainly used on the
Internet WEB site.
• It does not fit the TV screen (those images are reduced).
• If you cannot change the [MODE (MUSIC, IMAGE)] setting, re-load the disc
or turn the system off, then on.
• The DATA CD/DATA DVD contains a DivX video file.
files starts playing
simultaneously.
The DivX video file cannot be • The file is not created in DivX format.
played.
• The file has an extension other than “.AVI” or “.DIVX.”
• The DATA CD/DATA DVD is not created in a DivX format that conforms to
ISO 9660 Level 1/Level 2 or, Joliet/UDF.
• The DivX video file is larger than 720 (width) × 576 (height).
The titles of folder/file/file name • The system can only display numbers and letters of the alphabets. Other
are not displayed correctly.
characters are displayed as [*].
A disc does not start playing
from the beginning.
• Program Play, Shuffle Play, or Repeat Play has been selected.
Press CLEAR to cancel these functions before playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and then start playback
• The title, DVD or PBC menu automatically appears on the TV screen.
The system starts playing the
disc automatically.
• The DVD features an auto playback function.
Playback stops automatically.
• Some discs may contain an auto pause signal. While playing such a disc, the
system stops playback at the auto pause signal.
You cannot perform some
functions such as stop, search,
Slow-motion Play, or Repeat
Play.
• Depending on the disc, you may not be able to perform some of the operations
above. Refer to the operating instructions supplied with the disc.
GB
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in
TV screen in the language you
want.
[OSD] under [LANGUAGE SETUP] (page 51).
The language for the sound track • Multilingual tracks are not recorded on the DVD being played.
cannot be changed.
• The DVD prohibits changing the language for the sound track.
The subtitle language cannot be • Multilingual subtitles are not recorded on the DVD being played.
changed.
• The DVD prohibits changing the subtitles.
The subtitle cannot be turned off. • The DVD prohibits turning off subtitles.
• The DVD prohibits changing the angles.
A disc cannot be ejected and
“LOCKED” appears in the front
panel display.
• Contact your Sony dealer or local authorized Sony service facility.
[Data error] appears on the TV • The MP3 file/JPEG image file/DivX video file you want to play is broken.
screen when playing a DATA
CD or DATA DVD.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to DCF.
• The JPEG image file has the extension “.JPG” or “.JPEG,” but is not in JPEG
format.
• The file you want to play has the extension “.AVI” or “.DIVX” but is not in
DivX format, or is in DivX format but does not conform to a DivX Certified
profiles.
The system does not work
normally.
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then
reconnect after several minutes.
The Control for HDMI function • When “HDMI” does not light up in the front panel display, check the HDMI
does not work.
• Set the [CONTROL FOR HDMI] setting in [HDMI SETUP] to [ON] (page 52).
• Make sure that the connected component is compatible with the [CONTROL
FOR HDMI] function.
• Check that the AC power cord (mains lead) of the connected component is
connected securely.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power
cord (mains lead), or have a power failure, set the [CONTROL FOR HDMI]
setting in [HDMI SETUP] to [OFF], then set the [CONTROL FOR HDMI]
setting in [HDMI SETUP] to [ON] (page 52).
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
No sound is output from the
system and TV while using the
System Audio Control function.
• Make sure that the connected TV is compatible with the System Audio Control
function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
GB
95
Download from Www.Somanuals.com. All Manuals Search And Download.
USB device
Symptom
Remedy
“OVERLOAD” appears in the • A problem has been detected with the level of electrical current from the
front panel display.
(USB) port. Turn off the system and remove the USB device from the
(USB) port. Make sure there is no problem with the USB device. If this display
pattern persists, contact your nearest Sony dealer.
Are you using a supported USB • If you connect an unsupported USB device, the following problems may occur.
device?
See “Playable USB Devices” (supplement) for the supported device types.
– The USB device is not recognized.
– File or folder names are not displayed on this system.
– Playback is not possible.
– The sound skips.
– There is noise.
– A distorted sound is output.
– Recording stops before it is finished.
There is no sound.
• The USB device is not connected correctly. Turn off the system, then reconnect
the USB device.
The sound is distorted.
• The bit rate used when encoding the audio files was low. Send audio files
encoded with higher bit rates to the USB device.
There is noise or the sound skips. • Turn off the system, then reconnect the USB device.
• Noise may have entered during the recording or copying process. Delete the
file, and try recording or copying again.
• Copy the files to your computer, format the USB device in FAT12, FAT16, or
FAT32 format, and copy the files to the USB device again.*
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
The USB device cannot be
• The USB device is being connected backwards. Connect the USB device in the
correct orientation.
connected into the
port.
(USB)
The USB device which has been • It may be recorded in an unsupported format. If so, first take the precaution of
used on another device does not backing up important files on the USB device by copying them to your
work.
computer hard disk. Next, format the USB device with a FAT12, FAT16, or
FAT32 file system and transfer the backed-up audio files onto the USB device
again.*
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
“READING” is displayed for a • The reading process can take a long time in the following cases.
long time.
– There are many folders or files on the USB device.
– The file structure is extremely complex.
– The memory capacity is excessive.
– The internal memory is fragmented.
• Sony recommends following these guidelines.
– Total folders on the USB device: 200 or less
– Total files per folder: 150 or less
Erroneous display.
• Send the music data to the USB device again, as the data stored in the USB
device may have been corrupted.
• The character codes that can be displayed by this system are numbers and
alphabet only. Other characters are not displayed correctly.
GB
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
“DATA ERROR” appears in the • The audio file/JPEG image file you want to play is broken.
front panel display during
playback of an USB device.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to DCF.
• The JPEG image file has the extension “.JPG” or “.JPEG,” but is not in JPEG
format.
Playback does not start.
• Turn off the system, then reconnect the USB device.
• Connect the USB device that this system can play. See “Playable USB Devices”
(supplement).
• Press H to start play.
first track.
The USB device (audio file/
JPEG image file) cannot be
played back.
• USB device formatted with file systems other than FAT12, FAT16, or FAT32
are unsupported.*
• Files that are encrypted or protected by passwords, etc. cannot be played back.
• The MP3 file does not have the extension “.MP3.”
• The WMA file does not have the extension “.wma.”
• The AAC file does not have the extension “.m4a.”
• The data is not stored in the desired format.
• The MP3 files in format other than MPEG 1 Audio Layer 3 cannot be played
back.
• If you use partitioned USB device, only audio files on the first partition can be
played.
• The system can playback to a depth of 8 folders only.
• For audio files/JPEG image files, check the [MODE (MUSIC, IMAGE)] setting
• The number of folders has exceeded 200.
• The number of files has exceeded 150.
• For audio files/JPEG image files, the folder contains more than 150 files.
• The JPEG image file does not have the extension “.JPG” or “.JPEG.”
• The JPEG image file is larger than 3,072 (width) × 2,048 (height) in normal
mode, or more than 2,000,000 pixels in Progressive JPEG mode which is
mainly used on the Internet website.
• JPEG image files with a high width to length ratio cannot be played back.
• A WMA file that is the WMA DRM, WMA Lossless, or WMA PRO format
cannot be played back.
• An AAC file that is the AAC DRM or AAC Lossless format cannot be played
back.
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
Audio files or JPEG image files • After the system reads all files on the USB device, playback may take more
take longer to play back than
others.
time than usual if:
– the number of folders or files is very large.
– the folder or file organization structure is very complex.
– the memory capacity is very large.
– the file size is extremely large.
– the physical structure within the memory is fragmented.
• Sony recommends following these guidelines.
– Total folders on the USB device: 200 or less
– Total files per folder: 150 or less
GB
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
You cannot start recording/
copying to an USB device.
• The following problems may have occurred.
– The USB device is full.
– The number of MP3 files and folders on the USB device has reached the
upper limit.
– The USB device is write-protected.
Recording/copying is stopped
before it is finished.
• The communication speed of the USB device is extremely slow. Connect the
USB device that this system can play.
• If the recording, copying, and erase operations are repeated multiple times, the
file structure within the USB device becomes complex. Follow the procedure
in the operating instructions of the USB device to format the USB device. If the
problem persists, contact your nearest Sony dealer.
Recording to an USB device
results in an error.
• You are using an unsupported USB device. See “Playable USB Devices”
(supplement).
• The USB device was disconnected or the power was turned off during
recording/copying. Delete the partially-recorded file, and record/copy again. If
this does not fix the problem, the USB device may be broken. Follow the
procedure in the operating instructions of the USB device to format the USB
device. If the problem persists, contact your nearest Sony dealer.
Audio files or folders on the
USB device cannot be erased.
• Check if the USB device is write-protected.
• The USB device was disconnected or the power was turned off during erasing.
Delete the partially-erased file. If this does not fix the problem, the USB device
may be broken. Follow the procedure in the operating instructions of the USB
device to format the USB device. If the problem persists, contact your nearest
Sony dealer.
The S-AIR function
Symptom
Remedy
S-AIR connection is not
established (sound transmission
is not established), e.g., the
indicator of the S-AIR sub unit
does the following:
• Turns off.
• If you use another S-AIR main unit, place it more than 8 m (26 1/4 feet) away
from the unit.
• You performed pairing the unit and another S-AIR sub unit. Perform pairing of
• The unit is paired to another S-AIR sub unit. Cancel pairing.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Flashes.
• Turns red.
• Stop using another wireless product.
• The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is
connected and turn on the S-AIR sub unit.
GB
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Remedy
No sound is heard from the
S-AIR product.
• If you use another S-AIR main unit, place it more than 8 m (26 1/4 feet) away
from the unit.
• Install the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Stop using another wireless product.
• Change the “RF CHANGE” setting (page 80).
• Change the ID settings of the S-AIR main unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then turn on them.
There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 8 m (26 1/4 feet) away
from the unit.
• Install the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a
microwave oven.
• Install the S-AIR main unit and S-AIR sub unit away from other wireless
products.
• Stop using another wireless product.
• Change the “RF CHANGE” setting (page 80).
• Change the ID settings of the S-AIR main unit and S-AIR sub unit.
GB
99
Download from Www.Somanuals.com. All Manuals Search And Download.
When displaying the version
number on the TV screen
Self-diagnosis Function
(When letters/numbers appear in the
display)
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the TV screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case,
check the following table.
VER.X.XX
C:13:50
First 3
Cause and/or corrective action
characters of
the service
number
C 13
The disc is dirty.
,Clean the disc with a soft cloth
C 31
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
E XX
To prevent a malfunction, the
system has performed the self-
diagnosis function.
(XX is a
number)
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
Example: E 61 10
GB
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Specifications
Amplifier Section
Intermediate frequency
AM tuner section
Tuning range
10.7 MHz
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
North American, Mexican, and Latin American
models:
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*: 142
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
watts (per channel at 3
ohms, 1 kHz, 10% THD)
Subwoofer*: 140 watts (at
3 ohms, 80 Hz, 10% THD)
European, Russian, and Middle Eastern models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
Australian and New Zealand models:
531 kHz - 1,710 kHz (with
the interval set at 9 kHz)
*
Depending on the decoding mode settings and the
source, there may be no sound output.
Inputs (Analog)
TV (AUDIO IN)
AUDIO IN
Sensitivity: 450/250 mV
Sensitivity: 250/125 mV
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
Inputs (Digital)
TV (COAXIAL IN/OPTICAL IN)
Impedance: 75 ohms/-
Other models:
531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
530 kHz - 1,610 kHz (with
the interval set at 10 kHz)
AM loop antenna (aerial)
450 kHz
Outputs (Analog)
Phones
Accepts low- and high-
impedance headphones.
Antenna (aerial)
Intermediate frequency
Super Audio CD/DVD System
Video Section
Laser
Semiconductor laser
Outputs
VIDEO: 1 Vp-p 75 ohms
R/G/B: 0.7 Vp-p 75 ohms
HDMI OUT: Type A (19
pin)
(Super Audio CD/DVD: λ
= 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
Speakers
Signal format system
PAL/NTSC
Front (SS-TS82)
Speaker system
Full range Bass reflex,
Magnetically Shielded
65 mm cone type
3 ohms
108 mm × 540 mm × 78
mm (w/h/d)
USB Section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
32 kbps - 320 kbps
Speaker unit
Rated impedance
Dimensions (approx.)
WMA:
AAC:
48 kbps - 192 kbps
48 kbps - 320 kbps
290 mm × 1,045 mm -
1,230 mm × 290 mm (w/h/
d) with stand
Sampling frequencies
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48 kHz
Mass (approx.)
1.2 kg
WMA:
AAC:
44.1 kHz
44.1 kHz
2.9 kg with stand
(USB) port:
Maximum current:
Center (SS-CT80)
Speaker system
500 mA
Full range Bass reflex,
Magnetically Shielded
65 mm cone type
3 ohms
265 mm × 93 mm × 71 mm
(w/h/d)
Tuner Section
System
Speaker unit
Rated impedance
Dimensions (approx.)
PLL quartz-locked digital
synthesizer
FM tuner section
Tuning range
North American models: 87.5 MHz - 108.0 MHz
(100 kHz step)
Mass (approx.)
0.7 kg
Surround (SS-TS80)
Speaker system
Other models:
87.5 MHz - 108.0 MHz (50
kHz step)
Full range Bass reflex,
Magnetically Shielded
GB
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker unit
Rated impedance
Dimensions (approx.)
65 mm cone type
3 ohms
103 mm × 164 mm × 82
mm (w/h/d)
Glossary
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjusts
the speaker settings to your listening
Mass (approx.)
0.6 kg
Subwoofer (SS-WS80)
Speaker system
Speaker unit
Subwoofer Bass reflex
160 mm cone type
3 ohms
environment in a short period of time.
Rated impedance
Dimensions (approx.)
205 mm × 325 mm × 325
mm (w/h/d)
Dolby Digital
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
Mass (approx.)
5.2 kg
General
Power requirements
220 V - 240 V AC,
50/60 Hz
On: 170 W
Power consumption
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
Standby: 0.3 W (at the
Power Saving mode)
Output voltage (DIGITAL MEDIA PORT)
DC 5 V
Output current (DIGITAL MEDIA PORT)
700 mA
Dimensions (approx.)
430 mm × 66 mm × 385
mm (w/h/d) incl.
projecting parts
4.2 kg
Dolby Pro Logic II
Mass (approx.)
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
Design and specifications are subject to change
without notice.
• Standby power consumption 0.3 W.
• Halogenated flame retardants are not
used in the printed wiring boards.
• Over 85% power efficiency of
amplifier block is achieved with the
full digital amplifier, S-master.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
x Music mode
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
GB
102
Download from Www.Somanuals.com. All Manuals Search And Download.
surround speakers and a center speaker. The
surround speakers output monaural sound.
Medical band), such as wireless LANs and
Bluetooth applications.
DTS
Super Audio CD
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
comprises of stereo rear channel and there is
discrete subwoofer channel in this format. DTS
provides the same 5.1 discrete channels of high
quality digital audio. The good channel
separation is realized due to the all channel data
being recorded discretely and processed in
digitally.
Super Audio CD is a new high-quality audio
disc standard where music is recorded in the
DSD (Direct Stream Digital) format
(conventional CD is recorded in the PCM
format). The DSD format, using a sampling
frequency 64 times higher than that of a
conventional CD, and with 1-bit quantization,
achieves both a wide frequency range and a wide
dynamic range across the audible frequency
range, and so provides music reproduction
extremely faithful to the original sound.
HDMI (High-Definition Multimedia
Interface)
x Super Audio CD types
There are two types of discs, depending on the
Super Audio CD layer and CD layer
combination.
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Content Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
• Super Audio CD layer: A high-density
signal layer for Super Audio CD
• CD layer1): A layer that is readable by a
conventional CD player
Single layer disc
(a disc with a single Super Audio CD layer)
Parental Control
A function of the DVD to limit playback of the
disc by the age of the users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
Super Audio CD
layer
Hybrid disc2)
(a disc with a Super Audio CD layer and a CD layer)
S-AIR
(Sony Audio Interactive Radio
frequency)
Recent times have seen the rapid spread of DVD
media, Digital Broadcasting, and other high-
quality media.
CD layer3)
Super Audio CD
layer3)
To ensure that the subtle nuances of these high-
quality media are transmitted with no
deterioration, Sony has developed a technology
called “S-AIR” for the radio transmission of
digital audio signals with no compression, and
has incorporated this technology into the EZW-
RT10/EZW-T100.
This technology transfers digital audio signals
with no compression using the 2.4 GHz band
range of ISM band (Industrial, Scientific, and
A Super Audio CD layer consists of the 2
channel area or the multi-channel area.
• 2 channel area: An area in which 2 channel
stereo tracks are recorded
• Multi-channel area: An area in which multi-
channel (up to 5.1 channels) tracks are
recorded
GB
103
Download from Www.Somanuals.com. All Manuals Search And Download.
2 channel area4)
Multi channel area4)
Super Audio CD
layer
1)You can play the CD layer on a conventional CD
player.
2)Since both layers are on one side, it is not necessary
to turn the disc over.
GB
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
GB
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
Front panel
J
(USB) port (65)
E
GB
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
Screws*
ANTENNA
SPEAKER
FRONT
R
FRONT
L
SUR
R
SUR
L
EZW-T100
COAXIAL 75
FM
AM
SPEAKER
DIGITAL IN
EURO AV
CENTER
SUBWOOFER
DC5V
0.7A MAX
COAXIAL
OPTICAL
OUTPUT(TO TV)
TV
HDMI OUT
DMPORT
F DMPORT (DIGITAL MEDIA PORT) jack
H TV (DIGITAL IN COAXIAL/OPTICAL)
jacks (20)
*
CAUTION
Please do not remove the screws before
installing the EZW-T100.
GB
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
About the indications in the front panel display
A Playing status
G Lights up when the HDMI OUT jack is
correctly connected to HDCP (High-
bandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input. (20)
B Flashes when the sleep timer is set.
C Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, decoding mode, etc.
H Current surround format (Except for
JPEG image file)
I Lights up when an NTSC disc is
D Lights up when a station is received.
loaded.
J Lights up during USB recording/
E Stereo/Monaural effect (Radio only)
K Lights up when Super Audio CD/CD is
F Lights up when the S-AIR transmitter
(not supplied) is inserted in the unit
and the system transmits the sound.
loaded. (36)
GB
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A – O
P – Z
S-AIR MODE 4
C/X/x/c/
1)
DISC SKIP ed
REPLAY/ADVANCE
85)
2)
STEP
/
SLOW
/
81)
3)
1)This button is not available
for this model.
2)The ENTER button has the
same function as the
button. When you operate
the TV, the ENTER button is
used for selecting a channel,
and the
button is used for
selecting menu items
3)This button is available for
the “DVD,” “USB,” or
“DMPORT” function.
Depending on the DIGITAL
MEDIA PORT adapter, this
button may not work.
GB
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
You can use the Control Menu display to select a function and to view related information.
DISPLAY
Press
DISPLAY repeatedly.
DISPLAY, the Control Menu display changes:
Each time you press
1 t 2 t ... t 1 t ...
1 Control Menu display 1
2 Control Menu display 2 (appears when available)
3 Control Menu display off
Note
• The Control Menu Display appears during the “DVD,” “USB,” or “DMPORT” function. Depending on the
DIGITAL MEDIA PORT adapter, the Control Menu Display may not appear.
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For details,
see the pages in parentheses.
GB
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing title number
Currently playing chapter number
Total number of titles
Playback status
(N Playback,
Total number of chapters
Control Menu items
X Pause,
x Stop, etc.)
98( 99)
13( 99)
Type of disc being
played
DVD VIDEO
T
0: 04: 17
Selected item
OFF
OFF
DISC
Playing time
TITLE
CHAPTER
Current setting
Options
Function name of selected
Control Menu item
REPEAT
ENTER
DISPLAY
Quit:
Operation message
To turn off the display
Press DISPLAY.
List of Control Menu items (except for USB device)
Item
Item Name, Function, Relevant Disc Type
You can select the title, scene, or track to be played.
You can select the chapter or index to be played.
[INDEX] (page 41)
You can display the index and select the index to be played.
[TRACK] (page 41)
You can select the track to be played.
[ORIGINAL/PLAY LIST] (page 41)
You can select the type of titles (DVD-RW/DVD-R) to be played, the [ORIGINAL] one, or
an edited [PLAY LIST].
[TIME] (page 42)
You can check the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
The system displays the DVD/Super Audio CD/CD text or the MP3 file name.
[MULTI/2CH] (page 36)
You can select the playback area on a Super Audio CD when available.
[SUPER AUDIO CD/CD LAYER] (page 36)
You can select the playback layer on a Super Audio CD when available.
GB
111
Download from Www.Somanuals.com. All Manuals Search And Download.
[PROGRAM] (page 38)
You can select the track to play in the order you want.
[SHUFFLE] (page 39)
You can play the track/file in random order.
[REPEAT] (page 40)
You can play the entire disc (all titles/all tracks/all folders/all files) repeatedly or one title/
chapter/track/folder/file repeatedly.
[A/V SYNC] (page 48)
You can adjust the delay between the picture and sound.
[DISC MENU] (page 41)
You can display the DVD’s menu.
[BROWSING] (page 44)
You can display the list of folders/JPEG image files.
[SETUP] (page 50)
[QUICK] (page 25)
You can make the basic adjustments. Use Quick Setup to select the desired language of the
on-screen display, the aspect ratio of the TV, and select yes or no to start the Auto Calibration.
[CUSTOM]
In addition to the Quick Setup setting, you can adjust various other settings.
[FOLDER] (page 41)
You can select the folder to be played.
[FILE] (page 41)
You can select the JPEG image file or DivX video file to be played.
[DATE] (page 87)
You can display the date the picture was taken by a digital camera.
*
*
[INTERVAL] (page 45)
You can select the duration for which the slides are displayed on the TV screen.
[EFFECT] (page 45)
You can select the effects to be used for changing slides during a slide show.
*
*
[MODE (MUSIC, IMAGE)] (page 44)
You can select the data type; MP3 file, JPEG image file, or both to be played when playing a
DATA CD/DATA DVD.
* These items are not displayed when playing a DATA CD/DATA DVD with DivX video file.
List of Control Menu Items for USB device
Item
Item Name, Function, Relevant Disc Type
[REPEAT] (page 69)
You can play the entire USB device (all folders/all files) repeatedly or one folder/file
repeatedly.
[BROWSING] (page 68)
You can display the list of folders/JPEG image files.
[DATE] (page 70)
You can display the date the picture was taken by a digital camera.
GB
112
Download from Www.Somanuals.com. All Manuals Search And Download.
[INTERVAL] (page 68)
You can select the duration for which the slides are displayed on the TV screen.
[EFFECT] (page 68)
You can select the effects to be used for changing slides during a slide show.
You can select the data type; audio file or JPEG image file, when playing a USB device.
[USB RECORDING] (page 71)
You can record tracks on an audio CD or copy MP3 files on an DATA CD to a USB device.
Tip
• The Control Menu icon indicator lights up in yellow
([PROGRAM], [SHUFFLE], [REPEAT], and [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights
up in yellow when you select [PLAY LIST] (default setting).
t
when you select any item except [OFF]
GB
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
H
HDMI
R
A
HDMI (High-Definition
Multimedia Interface) 103
I
S
J
B
L
C
M
D
N
T
DivX® 46, 55
O
U
P
V
E
W
F
Q
GB
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
(1)
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|