Sony Headphones headphone User Manual
OPERATING MANUAL  
Bluetooth Enabled Car Kit  
Version 3.5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
·
Wireless Microphone Illustration  
Figure 3  
Figure 2  
REMARKS:  
§
§
§
§
If microphone is not “ON” during a communication, the sound on the speaker will be  
attenuated.  
In standby mode, the microphone will still have a small consumption (less than 1.8  
microwatts).  
On some versions, the indicator light will only turn ON for 2 seconds after the  
microphone is switched ON. If the light is red, this indicates low battery.  
The microphone is activated by the Hands-Free Car Kit base and can remain in “ON”  
position even if not used. But in order to extend battery life, it is recommended to switch  
“OFF” your microphone when you won’t use it for a long time.  
C. FUNCTION CONTROLS  
Adjust the Function Controls as recommended:  
1.  
2.  
3.  
Tone Control  
“H” for High Tone  
“L” for Low Tone.  
ASP Control  
ON = Echo and Feedback Canceller  
OFF = Echo Reducer only  
Adjustable Microphone Gain (MIC) Control  
“H” for high gain; “L” for low gain.  
"L" is necessary in noisy background.  
Control Switches  
Figure 4.  
The Microphone gain must be adjusted to match with your cell phone model. If the gain is too  
high, it can cause feedback (whistling sound), echo or background noise during calls on some  
cell phones.  
Note:  
Recommended Function Controls  
Setting (Working on all models):  
On high background environment,  
If you experience audio level  
fluctuation, turn ASP ‘’ OFF ’’.  
MIC  
=
=
=
L
ASP  
TONE  
ON  
H
D. SETTING THE VOLUME  
There are two volume controls. One is on the main unit. See (4) on figure 1. The other is the  
volume key of your cell phone. Use the volume control of the Car Kit and the volume keys of  
your cell phone. Note: If the volume set is too high, it can cause feedback (whistling sound),  
echo or background noise during calls on some cell phones.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
E. ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, the phone ring tone will be heard on the Car Kit. Just  
press the multi-function button (1) on the main unit to answer the call. Pressing the button  
again will hang-up and terminate the call. (Please refer to Car Kit Operations for Popular Cell  
Phones section on page 4 for additional information).  
F. MAKING A CALL  
(Refer to Car Kit Operations For Popular Cell Phones section on page 4).  
Important Remarks:  
·
On some versions of Nokia’s software, the Car Kit will not connect automatically to the  
cell phone. You will need to press the multi-function button once to connect it to the cell  
phone.  
·
If disconnection problem will be encountered on some Nokia cell phones, kindly turn off  
the keypad tone of your cell phone.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAR KIT OPERATIONS FOR POPULAR  
CELL PHONES  
Note 1: If your phone is not included in the following list of this manual, kindly refer to the manual  
of your phone.  
Note 2: Softwares and menus could be modified by the cell phone’s manufacturers without prior  
notice. If the manual does not match with your cell phone operations, kindly refer to the manual of  
your cell phone.  
Note 3: Multi-pairing is now possible.  
Ericsson T39m  
Sony Ericsson T68/T68i  
Sony Ericsson P800 / P900  
Sony Ericsson T610  
Sony Ericsson T628  
Sony Ericsson Z600  
Sony Ericsson K700i  
Motorola E398  
Motorola V80  
………………………………….………………………  
……………………………….…………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
………………………………….………………………  
8
9
12  
14  
15  
17  
18  
20  
22  
23  
25  
27  
29  
31  
33  
34  
36  
38  
40  
41  
42  
Motorola V600  
Nokia 6310/6310i  
Nokia 8910  
Nokia 8910i  
Nokia 3650  
Nokia 6230  
Nokia 6650  
Nokia 6600  
Panasonic X70  
Qtek 2020  
Sharp GX32  
Siemens S55  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Suggested Pairing Modes  
Pairing Mode  
Handsfree Headset  
Cell Phone Models  
Ericsson T39m  
Sony Ericsson T68  
Sony Ericsson T68i (R6 and below)  
Sony Ericsson T68i (R7)  
Sony Ericsson P800 / P900  
Sony Ericsson T610  
Sony Ericsson T628  
Sony Ericsson Z600  
Sony Ericsson K700i  
Motorola E398  
Motorola V80  
Motorola V600  
Nokia 6310/6310i  
Nokia 8910  
Nokia 8910i  
Nokia 3650  
Nokia 6230  
Nokia 6650  
Nokia 6600  
Panasonic X70  
Qtek2020  
Sharp GX32  
Siemens S55  
The Car Kit turns on automatically when the engine is turned on. The  
ON state is designated by the Bluetooth indicator LED flashing “Blue”.  
Note 1: Handsfree Pairing Mode  
From the ON state, press the multi-function button for 10 seconds or  
until a distinctive three-tone sound will be heard and at the same time,  
the Bluetooth indicator LED changes from blinking blue to alternate  
blinking of red and blue. This indicates that the unit is now ready for  
Handsfree Pairing.  
Note 2: Headset Pairing Mode  
From the ON state, press the multi-function button for 10 seconds or  
until a distinctive three-tone sound will be heard and at the same time,  
the Bluetooth indicator LED changes from blinking blue to alternate  
blinking of red and blue.  
Press the multi-function button again for a short time to access  
Headset Pairing Mode.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING WITH SONY ERICSSON T39m  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between  
your mobile phone and other Bluetooth devices.  
1.  
Press Menu Key. Scroll to Extras and press YES. Select Operation mode, YES. On,  
YES.  
2.  
Continue pressing NO to exit.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Extras  
Blue tooth  
Operation mode  
T39m  
5
6
4
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Press the multi-function button once again for a short time, to access headset  
pairing mode.  
Press Menu Key. Scroll to Extras, YES. Select Bluetooth, YES. Select Paired devices,  
YES. Add device, YES. Choose Phone initiates, YES. Choose Headset, YES. The  
phone will then search the device to be added. After the device is found, press YES.  
QUICK ACCESS (for step 4):  
Press Menu then follow the sequence of numbers below:  
Paired  
devices  
2
Add  
device  
Yes  
Phone  
initiates  
1
Extras  
Blue tooth  
Headset  
T39m  
5
6
2
5.  
6.  
Enter “0000” as the passkey. If the pairing is successful, the alternating red/blue lights  
will stop. Press YES to confirm the name of the device. If pairing is unsuccessful, the  
steps above may be repeated.  
Continue pressing NO to exit from Menu.  
The unit is now ready to link calls from the phone directly to the Car Kit.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Press the multi-function button once to answer the call. Note: Pressing the button again  
will hang-up and terminate the call.  
2.  
If you wish to answer the call on the cellular phone, just press YES and audio will be  
heard on the phone. If you press once on the multi-function button, audio will be  
transferred to the Car Kit.  
3.  
Pressing the multi-function button once again will terminate the call.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press YES. Audio can be heard on the Car Kit.  
Simultaneously, a question “Retrieve call in phone?” will be displayed. Ignoring  
or pressing No, will retain the call to the Car Kit. Pressing Yes will transfer the  
audio to the cell phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Voice dialing  
Refer to step f and g for the procedure when activating and recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
4.  
Press the multi-function button once again to terminate the call.  
e.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the name dialing function and record your voice. To turn voice dialing on and record number  
types:  
1.  
2.  
3.  
Press Menu Key. Scroll to Settings, YES. Voice control, YES.  
Voice settings, YES. Voice dialing, YES. Select On, YES.  
Continue pressing NO to exit.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Settings  
Voice control  
Voice settings  
Voice dialing  
On  
T39m  
4
9
1
1
1
g.  
RECORDING FOR VOICE DIALING  
1.  
2.  
3.  
Press Menu Key. Scroll to Settings, YES. Voice control, YES. Voice Commands, YES.  
Select Contacts, YES. Add voice, YES.  
Find a contact name and follow the instructions in the display. An icon will appear next  
to a contact name which has a voice command.  
Continue pressing NO to exit.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Settings  
Voice control  
Voice commands  
Contacts  
T39m  
4
9
2
4
Note: Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
USING WITH SONY ERICSSON T68/T68i  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Go to Menu by pressing the joystick. Scroll to Connect, YES. Select Bluetooth, YES.  
Select Options, YES. Operation mode, YES. On, YES.  
Continue pressing NO to exit.  
2.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Connect  
Blue tooth  
3
4 (or 3 for T68i R7)  
Options  
Operation mode  
T68  
T68i  
8
8
-
4
2
1
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
For T68 and T68i older versions, R6 and below, press the multi-function button  
once again for a short time, to access headset pairing mode.  
4.  
5.  
Go to Menu by pressing the joystick. Scroll to Connect, YES. Select Bluetooth, YES.  
Select Paired devices, YES. Add device, YES. Choose Phone initiates, YES. Choose  
Headset/Handsfree, YES. The phone will then search the device to be added. After the  
device is found, press YES.  
QUICK ACCESS (for steps 4 and 5):  
Press Menu then follow the sequence of numbers below:  
Paired  
devices  
Add  
device  
Phone  
initiates  
Headset/  
Handsfree  
Connect  
Blue tooth  
T68  
8
8
3
2
2
Yes  
Yes  
1
1
2
2
T68i  
4 (or 3 for T68i R7)  
6.  
Enter “0000” as the passkey. If pairing is successful, the alternating red/blue lights will  
stop. Press YES to confirm the name of the device. If pairing is unsuccessful, the steps  
above may be repeated.  
7.  
Continue pressing NO to exit from menu.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear  
during the standby mode indicating that the Car Kit is linked with the phone.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Just press the multi-function button once to answer the call. Pressing the button again  
will hang-up and terminate the call.  
2.  
If you wish to answer the call on the cellular phone, just press YES and the call will be  
heard on the phone. Pressing the multi-function button will transfer the call to the Car  
Kit.  
3.  
To terminate the call, press the multi-function button again.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press YES. Audio will be heard on the Car Kit.  
Simultaneously, a question “Retrieve call in phone?” will be displayed. Ignoring  
or pressing No, will retain the audio to the Car Kit. Pressing Yes, will transfer the  
audio to the cell phone.  
2.  
Press the multi-function button to terminate the call.  
Voice dialing  
Refer to step g and h for the procedure when activating and recording for voice dialing.  
1.  
Press the multi-function button once to activate the voice dialing.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
4.  
Press the button again to terminate the call.  
Redialing  
For T68i R6 and R7, press twice quickly the multi-function button. Call is automatically  
transferred to the Car Kit.  
e.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
f.  
REJECTING A CALL  
For T68i R6 and R7, press the multi-function button twice to reject the incoming call.  
g.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the name dialing function and record your voice. To turn voice dialing on and record number  
types:  
Using T68 Sony Ericsson  
1.  
2.  
3.  
Go to Menu by pressing the joystick. Scroll to Settings, YES. Voice control, YES.  
Voice settings, YES. Voice dialing, YES. Select On, YES.  
Continue pressing NO to exit  
Using T68i Sony Ericsson  
1.  
Go to Menu by pressing the joystick. Scroll to Settings, YES. Voice control, YES.  
Voice dialing, YES.  
2.  
3.  
Select On, YES.  
Continue pressing NO to exit  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Voice  
control  
Voice  
settings  
Voice  
dialing  
Settings  
On  
T68  
T68i  
5
5
8
6
1
-
1
1
1
1
h.  
RECORDING FOR VOICE DIALING  
Using T68 Sony Ericsson  
1.  
Go to Menu by pressing the joystick. Scroll to Settings and press YES. Choose  
Voice control, YES. Voice Commands, YES. Select a contact, YES. Add voice,  
YES.  
2.  
3.  
Follow the instructions in the display. An icon will appear next to a contact name  
which has a voice command.  
Continue pressing NO to exit.  
Using T68i Sony Ericsson  
1.  
Go to Menu by pressing the joystick. Scroll to Settings and press YES. Choose  
Voice control, YES then go to Voice dialing, YES. Edit name, YES. Add voice,  
YES.  
2.  
Select a contact, YES.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
4.  
Follow the instructions in the display. An icon will appear next to a contact name  
which has a voice command.  
Continue pressing NO to exit.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Settings  
Voice control  
Voice commands  
Contacts  
T68  
5
Settings  
5
8
2
4
Voice control  
Voice dialing  
Edit names  
T68i  
6
1
2
Note: Record your voice command in a quiet place so that only your voice will be  
recorded on the phone.  
USING WITH SONY ERICSSON P800 / P900  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Flip to open mode. On the phone’s Applications window, scroll to Control Panel and  
tap it using the “stylus”. On the lower portion, tap Connections index. Tap  
Bluetooth.Tap Settings index. On the Operation mode, tap On.  
2.  
Tap  
to exit and return to the Applications window.  
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Press the multi-function button once again for a short time, to access headset  
pairing mode.  
Flip to open mode. On the phone’s Applications window, scroll to Control Panel and tap  
it. On the lower portion, tap Connections index. Tap Bluetooth. Tap Devices index.  
Bluetooth devices is displayed as sub-title. Tap Add. The phone is now searching for  
pairable devices.  
5.  
6.  
7.  
Devices found are then displayed. Tap the device you want to pair with your phone.  
Bonding in progress will be displayed on screen and simultaneously, the phone will  
ask for the pass key.  
On the lower left corner of the screen, tap  
. Enter “0000” as the passkey then tap  
Done. Also tap Done under the sub-title, “Secure Connection.” If pairing is successful,  
the alternating red/blue lights will stop.  
Tap  
to exit and return to the Applications window. If the pairing is unsuccessful, the  
steps above may be repeated.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon will  
appear during the standby mode indicating that the Car Kit is linked with the phone.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Press the multi-function button once to answer the call. Pressing the button again will  
hang-up and terminate the call.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
If you wish to answer the call on the cellular phone, just press ok key and audio will be  
heard on the phone. Pressing the multi-function button will transfer the audio to the Car  
Kit.  
To terminate the call, press the multi-function button again.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press OK. Sound is automatically transferred to the  
Car Kit.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step f and g for the procedure when activating and recording for voice dialing.  
1.  
2.  
3.  
Press the multi-function button once to activate the voice dialing. Sound is  
automatically transferred to the Car Kit.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
4.  
Press the button again to terminate the call.  
e.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for the voice dialing. Before voice dialing, you must first turn  
on the name dialing function and record your voice. To turn voice dialing on:  
1.  
2.  
3.  
On the Applications window (flip open mode), tap Phone.  
Tap Edit then tap Preferences. A list of features will appear.  
Tap Voice Control then tap the box aligned to Voice dialing to check and activate the  
voice dialing feature. Tap the box aligned to Play caller name so that the name will be  
played back to you.  
4.  
5.  
6.  
Tap Done on the on screen button when finished.  
On the Preferences mode, tap Done again.  
Tap  
to exit and return to the Applications mode.  
g.  
RECORDING FOR VOICE DIALING  
The voice dialing feature is only applicable to contacts saved to phone memory.  
1.  
On the Applications window (flip open mode), tap Contacts.  
2.  
Tap the contact where you want to add a voice dialing feature. Tap Edit. Scroll to Edit  
Contact. Tap  
on the on-screen buttons.  
3.  
4.  
Tap Record. Speak after tone will be displayed on the screen.  
Record your voice. To check if your recording is of good quality, tap Play. If not, tap  
Record again. Press Done when finished.  
5.  
Tap  
to make another record and repeat the steps above. To return to the  
button.  
Applications window, tap  
Note: Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING WITH SONY ERICSSON T610  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,  
SELECT. Turn On, SELECT.  
2.  
Continue pressing  
to exit.  
PAIRING TO THE CELLULAR PHONE  
1.  
Bring the cellular phone at about 20 cm from the Car Kit.  
2.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,  
SELECT.  
Scroll to My devices, SELECT. New device, ADD. The phone is now searching for  
pairable devices to be added. Select the device you want to pair with your cell phone.  
Press SELECT.  
5.  
6.  
Enter “0000” as the passkey then press OK. If the pairing is successful, the alternating  
red/blue lights will stop.  
Continue pressing  
to exit.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon will appear  
during the standby mode indicating that the Car Kit is linked with the phone.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Just press the multi-function button down once to answer the call. Pressing the button  
again will hang-up and terminate the call.  
2.  
If you wish to answer a call on the cellular phone, just press YES and the call is  
automatically transferred to the phone. Pressing the multi-function button transfers the  
call on the Car Kit.  
3.  
To terminate the call, press the multi-function button again.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press CALL button. Audio is automatically  
transferred to the Car Kit.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step g and h for the procedure when activating and recording for voice dialing.  
1.  
2.  
3.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
4.  
Press the multi-function button again to terminate the call.  
Redialing  
Press quickly the multi-function button twice to redial the last number.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
e.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
f.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
g.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for the voice dialing. Before voice dialing, you must first turn  
on the name dialing function and record your voice. To turn voice dialing on and record  
number types:  
1.  
Go to Menu by pressing the joystick. Scroll to Settings, SELECT. Voice control,  
SELECT. Voice dialing, SELECT.  
2.  
3.  
Choose On, SELECT.  
Continue pressing  
to exit.  
h.  
RECORDING FOR VOICE DIALING  
1.  
Go to Menu by pressing the joystick. Scroll to Settings and press SELECT. Choose  
Voice control, SELECT then go to Voice dialing, SELECT. Edit names, SELECT. New  
voice, ADD.  
2.  
3.  
Find a contact then press SELECT.  
Follow the instructions that are displayed. Voice is automatically saved on the phone.  
An icon will appear next to a contact name which has a voice command.  
4.  
Continue pressing  
to exit.  
Note: Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
USING WITH SONY ERICSSON T628  
a.  
ACTIVATING THE BLUE TOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,  
SELECT. Turn On, SELECT.  
2.  
Continue pressing  
to exit.  
b.  
c.  
SETTING TO LOW POWER MODE  
1.  
Press Menu Key. Scroll to Connectivity, SELECT. Bluetooth, SELECT.  
Scroll to Handsfree, SELECT. Choose Car handsfree, SELECT.  
Choose Power Save, SELECT.  
2.  
3.  
4.  
Continue pressing  
to exit.  
PAIRING TO THE CELLULAR PHONE  
1.  
Bring the cellular phone at about 20 cm from the Car Kit.  
2.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Go to Menu by pressing the joystick. Scroll to Connectivity, SELECT. Select Bluetooth,  
SELECT.  
Scroll to My devices, SELECT. New device, ADD. The phone is now searching for  
pairable devices to be added. Select the device you want to pair with your cell phone.  
Press SELECT.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.  
6.  
Enter “0000” as the passkey then press OK. If the pairing is successful, the alternating  
red/blue lights will stop.  
Continue pressing  
to exit from Menu.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear  
during the standby mode indicating that the Car Kit is linked with the phone.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Just press the multi-function button down once to answer the call. Pressing the button  
again will hang-up and terminate the call.  
2.  
If you wish to answer a call on the cellular phone, just press YES and audio will be  
heard on the phone. Pressing the multi-function button will transfer the call on the Car  
Kit.  
3.  
To terminate the call, press the multi-function button again.  
e.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press CALL button. Audio is automatically  
transferred to the Car Kit.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step g and h for the procedure when activating and recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the multi-function button again to terminate the call.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the name dialing function and record your voice. To turn voice dialing on and record number  
types:  
1.  
Go to Menu by pressing the joystick. Scroll to Settings, SELECT. Voice control,  
SELECT. Voice dialing, SELECT.  
2.  
3.  
Choose On, SELECT.  
Continue pressing  
to exit.  
h.  
RECORDING FOR VOICE DIALING  
1.  
Go to Menu by pressing the joystick. Scroll to Settings and press SELECT. Choose  
Voice control, SELECT then go to Voice dialing, SELECT. Edit names, SELECT. New  
voice, ADD.  
2.  
3.  
Find a contact then press SELECT.  
Follow the instructions that are displayed. Voice is automatically saved on the phone.  
An icon will appear next to a contact name which has a voice command.  
4.  
Continue pressing  
to exit.  
Note: Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING WITH SONY ERICSSON Z600  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Press Menu Key  
Turn ON, SELECT.  
Continue pressing  
. Scroll to Connectivity, SELECT. Bluetooth, SELECT. Choose  
2.  
to exit.  
QUICK ACCESS:  
a.  
b.  
c.  
Press More key.  
Scroll to Turn On Blue tooth, SELECT.  
Continue pressing to exit.  
b.  
c.  
SETTING TO LOW POWER MODE  
1.  
2.  
3.  
4.  
Press Menu Key  
Scroll to Handsfree, SELECT. Choose Car handsfree, SELECT.  
Choose Power Save, SELECT.  
Continue pressing  
. Scroll to Connectivity, SELECT. Bluetooth, SELECT.  
to exit.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Press Menu Key  
. Scroll to Connectivity, SELECT. Bluetooth, SELECT.  
Scroll to My Devices, SELECT. New Device, ADD. The phone will then search the  
device to be added. After the device is found, press SELECT.  
5.  
6.  
Enter “0000” as the passkey and press OK. If the pairing is successful, the alternating  
red/blue lights will stop. If pairing is unsuccessful, the steps above may be repeated.  
Continue pressing  
to exit.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon, will appear  
during the standby mode indicating that the Car Kit is linked with the phone.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit.  
1.  
Just press the multi-function button down once to answer the call. Pressing the button  
again will hang-up and terminate the call.  
2.  
If you wish to answer a call on the cellular phone, just press YES and the call is  
automatically transferred to the phone. To transfer the call to the Car Kit, Press Menu  
Key. Scroll to Transfer Sound and press SELECT. Choose the paired device and press  
SELECT.  
3.  
To terminate the call, press the multi-function button again.  
e.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. Audio can be heard on the Car Kit  
simultaneously.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step g and h for the procedure when activating and recording for voice dialing.  
1.  
Press the multi-function button once to activate the voice dialing.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
4.  
Press the button again to terminate the call.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for the voice dialing. Before voice dialing, you must first turn  
on the voice dialing function and record your voice. To turn voice dialing on:  
1.  
Press Menu Key  
. Scroll to Settings, SELECT. Scroll to Voice control, SELECT.  
Voice dialing, SELECT.  
Choose On, SELECT.  
Continue pressing  
2.  
3.  
to exit.  
h.  
RECORDING FOR VOICE DIALING  
1.  
Press Menu Key  
. Scroll to Settings and press SELECT. Choose Voice controls,  
SELECT then go to Voice dialing, SELECT. Scroll to Edit name, SELECT. New voice,  
ADD.  
2.  
3.  
Select a contact and press SELECT.  
Follow the instructions in the display. An icon will appear opposite a contact’s name  
which has a voice command.  
4.  
Continue pressing  
to exit.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
USING WITH SONY ERICSSON K700i  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate the Bluetooth feature of your phone to establish a Bluetooth connection  
between your mobile phone and other Bluetooth devices.  
1.  
2.  
3.  
Press  
Scroll to Connectivity, Select. Bluetooth, Select. Turn On, Select.  
Continue pressing to exit.  
to access Main Menu.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
5.  
Press  
Select.  
to access Main Menu. Scroll to Connectivity, Select. Choose Bluetooth,  
Scroll to My devices, Select. New device, Add. The phone will then search for pairable  
devices to be added.  
The searched devices will then be displayed. Choose the device name you want to pair  
with this phone, then press Select.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.  
7.  
Enter “0000” as the passcode then press Ok. If pairing is successful, the alternating  
red/blue lights (Bluetooth Indicator) will stop and will change to plain blinking blue.  
Your device name is now added under My devices tab. Highlight the newly paired  
device and then press Connect to completely establish connection between your mobile  
phone and your Car Kit.  
8.  
When a statement appeared indicating that your device is connected, continue pressing  
to exit.  
The Car kit is now linked or paired with the phone. If pairing is unsuccessful, the steps  
above may be repeated.  
c.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, ring tone will be heard on the phone and on the Car Kit.  
1.  
2.  
Shortly press the multi-function button once to answer the call.  
Shortly press the multi-function button once to terminate the call.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1. Enter the contact number and press Call key. Audio is possible on the phone or on  
the kit.  
At times, when the audio is not on the kit, apply audio transfer (see section e).  
2. To terminate or hang-up the call, shortly press the multi-function button.  
Voice dialing  
Refer to step h and i for the procedure when activating and recording for voice dialing.  
1.  
2.  
Shortly press the multi-function button once to activate voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the voice name  
of the person to call.  
3.  
4.  
Say the name. The voice name will be played back to you. The phone will then  
place the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
Shortly press the hang-up button to terminate the call.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
e.  
f.  
AUDIO TRANSFER  
Audio transfer can be done during an ongoing call.  
Car kit initiates transfer from kit to phone: Press twice quickly the multi-function button.  
Car kit initiates transfer from phone to kit: Shortly press the multi-function button once.  
Note: Using your phone, access  
to the Car Kit or to your phone.  
(Menu button) during an ongoing call to transfer sound  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
g. ACTIVATING THE VOICE DIALING  
Before voice dialing, you must first activate the voice dialing function of your cell phone and  
record a voice command for a particular contact.  
1.  
Press  
Voice dialing, Select. Activate, Select.  
Continue pressing to exit.  
to access Main Menu. Scroll to Settings, Select. Voice control, Select.  
2.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
h.  
RECORDING FOR VOICE DIALING  
Note: Voice dialing entries must be stored in the phone’s memory (not on the SIM  
card!).  
1.  
Press  
to access Main Menu. Scroll to Settings and press Select. Choose Voice  
control, Select. Voice dialing, Select. Edit names, Select. New voice, Add.  
(Contacts list will appear).  
2.  
3.  
4.  
5.  
Choose among the contacts whichever you want to have a voice name/voice tag. When  
it’s highlighted, press Select.  
Follow the instructions that will be displayed on screen.  
Note: You may use any word(s) or just say the person’s name for a voice tag.  
When your spoken word(s) is caught up by the phone, it will ask you to listen to your  
recording and will ask the question, “Is it ok?”.  
As soon as you press Yes as reply, your voice command will be saved. Under Voice  
Commands tab, a callout icon  
will appear next to a contact name which has a voice  
command.  
6.  
Continue pressing  
to exit.  
Note: Noisy environment may affect voice recognition. Record a voice and make a voice dial  
in a quiet environment.  
USING WITH MOTOROLA E398  
a.  
ACTIVATING THE BLUETOOTH  
You must activate the Bluetooth feature of your mobile phone to establish a Bluetooth  
connection between your mobile phone and other Bluetooth devices.  
1.  
Press  
or  
to access Main Menu.  
2.  
Scroll to Settings, SELECT. Scroll to Connection, SELECT. Bluetooth Link,  
SELECT.  
Set-up, SELECT. Scroll to Power: Off. Press CHANGE. Choose On, SELECT.  
3.  
Continue pressing BACK to exit.  
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
5.  
6.  
Press  
or  
to access Menu. Scroll to Settings, SELECT. Choose Connection,  
SELECT. Bluetooth Link, SELECT.  
Choose Handsfree, SELECT. [Look for devices], SELECT. The phone will then scan  
devices until it displays them in the list.  
Under scan results, choose the device you want to pair with your mobile phone and  
press SELECT. A question “Bond With (device name)?” appears. Press YES.  
Enter Bluetooth Passkey “0000” then press ok. If pairing is successful, a remark  
“Connected…” appears. The phone exits automatically.  
The Car kit is now linked or paired with the phone. If pairing is unsuccessful, the steps  
above may be repeated.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, ring tone will be heard on the phone and on the Car Kit.  
1.  
2.  
Shortly press the multi-function button once to answer the call.  
To terminate the call, do the same; shortly press the multi-function button once.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
e.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1. Enter the contact number and press Call key. Audio will be heard on  
the Car Kit.  
2. To terminate or hang-up the call, shortly press the multi-function button.  
Voice dialing  
Make a phone call by saying a voice name / voice tag. But first refer to step h and i for  
the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate voice dialing.  
A beep will then be heard on the Headset prompting the user to say the voice  
name / voice tag of the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
To terminate or hang-up the call, shortly press the multi-function button.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
e.  
f.  
AUDIO TRANSFER  
Audio transfer can be done during an ongoing call.  
Car kit initiates transfer from kit to phone: Press twice quickly the multi-function button.  
Car kit initiates transfer from phone to kit: Shortly press the multi-function button once.  
Note: Using your phone for audio transfer, press  
transfer audio by Selecting “Use Handset” or “Use Bluetooth”.  
button to access Call Menu and  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
g. ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the Voice Dial function and record your voice. To turn voice dialing on:  
1. Press  
or  
to access Menu. Scroll to Settings, SELECT. Scroll to Headset,  
SELECT.  
2. Choose Voice Dial, CHANGE. Choose ON, SELECT.  
3. Continue pressing Back to exit.  
i.  
RECORDING FOR VOICE DIALING  
Note: Voice dialing entries must be stored in the phone’s memory (not on the SIM  
card!).  
1.  
2.  
3.  
Press  
or  
to access Menu. Scroll to Phonebook, SELECT.  
Choose a contact which you want to have a voice name/tag, press VIEW then EDIT.  
On the Entry Details, choose “Store To: ____” and press CHANGE. Choose Phone,  
SELECT. (This is storing the number to phone memory).  
Highlight “Voice Name: ___” then press RECORD.  
4.  
Follow instructions on the screen. Note: You may use any word(s) or just the person’s  
name for a voice name/ tag.  
Note: If recording is successful, a statement “Trained: Voice Name” appears. An icon  
will appear next to Voice Name.  
5.  
6.  
Press DONE.  
Continue pressing  
key to exit.  
Note: In the listed names of your Phonebook, a symbol  
appears next to a name  
which has a “Voice Name”. This indicates that you can contact this person via “voice  
dial”.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING WITH MOTOROLA V80  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate the Bluetooth feature of your phone to establish a Bluetooth connection  
between your mobile phone and other Bluetooth devices.  
1.  
Press the joystick  
to access Menu. Scroll to Settings, SELECT. Choose  
Connection, SELECT. Bluetooth Link, SELECT.  
Scroll to Setup, SELECT. Scroll to Power, CHANGE. Choose ON, SELECT.  
Continue pressing Back to exit.  
2.  
3.  
PAIRING TO THE CELLULAR PHONE  
1. Bring the cellular phone at about 20 cm from the Car Kit.  
2.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3. Press the joystick  
to access Menu. Scroll to Settings, SELECT. Choose  
Connection, SELECT. Bluetooth Link, SELECT.  
4.  
5.  
6.  
Choose Hands-free, SELECT. [Look for devices], SELECT. The phone will then scan  
the device to be added.  
On the Scan results, choose the name of this car kit, SELECT. A question “Bond with  
… (device name)?” appears. Press YES.  
Enter Bluetooth passkey “0000” then press ok. If pairing is successful, a remark  
“Connected: (device name)” appears. The phone exits automatically.  
The Car kit is now linked or paired with the phone. If pairing is unsuccessful, the steps  
above may be repeated.  
c.  
f.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, ring tone will be heard on the phone and on the Car Kit.  
1.  
2.  
Shortly press the multi-function button once to answer the call.  
Shortly press the multi-function button once to terminate the call.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press Call key/Touch Sending key. Audio will be  
heard on the Car Kit.  
2. To terminate or hang-up the call, shortly press the multi-function button.  
Voice dialing  
Refer to step h and i for the procedure when activating and recording for voice dialing.  
1.  
2.  
Shortly press the multi-function button once to activate voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the voice name  
of the person to call.  
3.  
4.  
Say the name. The voice name will be played back to you. The phone will then  
place the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
Shortly press the hang-up button to terminate the call.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
e.  
AUDIO TRANSFER  
Audio transfer can be done during an ongoing call.  
Car kit initiates transfer from kit to phone: Press twice quickly the multi-function button.  
Car kit initiates transfer from phone to kit: Shortly press the multi-function button once.  
Note: Using your phone for audio transfer, press  
button of the 5-way navigation key. On  
the Call Menu, choose “Use handset” or “Use Bluetooth” to transfer audio to phone or to the  
kit.  
f.  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
g. ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the Voice Dial function and record your voice. To turn voice dialing on:  
1. Press the joystick  
SELECT.  
to access Menu. Scroll to Settings, SELECT. Scroll to Headset,  
2. Choose Voice Dial, CHANGE. Choose ON, SELECT.  
3. Continue pressing Back to exit.  
i.  
RECORDING FOR VOICE DIALING  
Note: Voice dialing entries must be stored in the phone’s memory (not on the SIM  
card!).  
1.  
2.  
3.  
Press the joystick  
to access Menu. Scroll to Phonebook, SELECT.  
Choose a contact which you want to make a voice dial, press VIEW then EDIT.  
On the Entry Details window, scroll to “Store To: ______”, press CHANGE. Choose  
Phone, SELECT. (This is storing the number to phone memory).  
Scroll to “Voice Name: ______” then press RECORD. Follow instructions on the  
screen.  
4.  
5.  
Note: If recording is successful, an icon will appear next to Voice Name.  
Press DONE.  
Notes: In the listed names of your Phonebook, an icon appears next to a name which  
has a “Voice Name”. This indicates that you can contact this person via “voice dial”.  
USING WITH MOTOROLA V600  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1. Press Menu key featured as  
or press on the center button of the 5-Way Navigation  
Key featured as to access Menu. Scroll to Settings, SELECT. Choose Connection,  
SELECT. Bluetooth Link, SELECT.  
2. Continue pressing Back to exit.  
PAIRING TO THE CELLULAR PHONE  
1. Bring the cellular phone at about 20 cm from the Car Kit.  
2.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu key  
or press on the center button of the 5-Way Navigation key  
to  
access Menu. Scroll to Settings, SELECT. Choose Connection, SELECT. Bluetooth  
Link, SELECT.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.  
5.  
6.  
Choose Handsfree, SELECT. [Look for devices], SELECT. The phone will then scan the  
device to be added.  
On the scan results, choose the device you want to pair with your cell phone, SELECT.  
A question “Bond with … (device name)?” appears. Press YES.  
Enter Bluetooth passkey “0000” then press ok. If pairing is successful, a remark  
“Connected to… (device name)” appears. The phone exits automatically.  
The unit is now ready to link calls from the phone directly to the Car Kit. If pairing is  
unsuccessful, the steps above may be repeated.  
c.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, ring tone will be heard on the Car Kit.  
1.  
2.  
Just press down the multi-function button once to answer the call.  
Press down the multi-function button once to terminate the call.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1. Enter the contact number and press SEND/ANS key. Audio will be heard on the  
Car Kit.  
2. To terminate or hang-up the call, press down the multi-function button once.  
Voice dialing  
Refer to step h and i for the procedure when activating and recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the hang-up button to terminate the call.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
e.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button once or accessing the cell  
phone’s menu during ongoing calls.  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
g. ACTIVATING THE VOICE DIALING  
Use your phone when recording for the voice dialing. Before voice dialing, you must first turn  
on the Voice Dial function of your phone and record your voice. To turn voice dialing on:  
1. Go to Menu by pressing the feature  
. Scroll to Settings, SELECT. Scroll to Headset,  
SELECT.  
2. Choose Voice Dial, CHANGE. Choose ON, SELECT.  
3. Continue pressing Back then finally Exit.  
h.  
RECORDING FOR VOICE DIALING  
Note: (Make sure the number is stored in Phone memory).  
1.  
Press Menu key featured as  
or press on the center button of the 5-Way Navigation.  
Key featured as to access Menu. Scroll to Phonebook, SELECT.  
2.  
Choose a contact which you want to make a voice dial, then press  
then press SELECT.  
. Choose Edit,  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
4.  
On the Entry Details, choose “…MORE…” and press SELECT.  
On the Add New, choose Phone Number, SELECT. “No.:_______” is highlighted,  
Press CHANGE. Enter the corresponding contact number and then press Ok. (Do not  
press DONE yet).  
5.  
6.  
Using the 5-way Navigation key  
Follow instructions on the screen.  
Note: If recording is successful, an icon will appear next to Voice Name.  
Press DONE.  
scroll down to “Voice Name” then press RECORD.  
Notes: 1. The recorded voice will be played back to you.  
2. On the listed names in your Phonebook, an icon appears next to a name  
which has a “Voice Name”. This indicates that you can contact this person via  
voice dial.  
3. Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
USING WITH NOKIA 6310/6310i  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Press the Menu button. Scroll to Bluetooth, SELECT. Press SELECT again.  
Choose On, SELECT. An icon will appear on the upper left corner.  
Press Back then Exit to get out of Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Blue tooth  
Select  
On  
1
1
Select  
6310  
6310i  
10  
11  
1
1
1
1
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu button. Scroll to Bluetooth, SELECT. Scroll to Search for audio  
accessories, SELECT. The phone is now scanning for Bluetooth devices. SELECT the  
Car Kit. The phone will initiate connection with the Car Kit.  
QUICK ACCESS (for step 3):  
Press Menu followed by the sequence of numbers below.  
Bluetooth  
Search for audio accessories  
6310  
6310i  
10  
11  
2
2
4.  
5.  
Enter “0000” as the passcode then press OK. The phone is now connected with the Car  
Kit.  
Continue pressing Back then finally Exit.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: Once paired, the Car Kit and phone have simultaneous connection with each other.  
(Keypad tones can be heard on the Car Kit when keypad is pressed).  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
2.  
3.  
Press the Menu button. Scroll to Bluetooth, SELECT. Scroll to View paired  
devices, SELECT.  
Select the Car Kit and press OPTIONS. Scroll to Request conn. authorisation, SELECT.  
No, SELECT.  
Continue pressing Back to exit from Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Bluetooth  
View paired devices  
Select  
Options  
Options  
6310  
6310i  
10  
11  
4
4
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, ring tones will be heard on the Car Kit as well as on the  
phone.  
1.  
2.  
Press the multi-function button down once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. As you dial, audio and the keypad tones can  
be heard on the Car Kit simultaneously but not on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press quickly the multi-function button twice to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
h.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
3.  
Press the Names button. Search, SELECT. Press List button.  
Find a contact name. Press Details button.  
Press Options button. Add voice tag, SELECT. Instructions appear. Your voice is  
automatically saved on the phone after being played back to you.  
In case you wish to change your recorded voice, press Options button. Voice tags,  
SELECT. Change, SELECT. Instructions appear.  
4.  
5.  
Continue pressing Back button to exit.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
USING WITH NOKIA 8910  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Press Menu. Scroll to Bluetooth, SELECT. Press SELECT again.  
Choose On, SELECT. An icon will appear on the upper left corner.  
Press Back then finally Exit.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Bluetooth  
Select  
On  
Select  
8910  
10  
1
1
1
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu. Scroll to Bluetooth, SELECT and Search for audio accessories, SELECT.  
The phone is now scanning for Bluetooth devices. SELECT the Car Kit. The phone will  
initiate connection with the Car Kit.  
QUICK ACCESS (for step 3):  
Press Menu followed by the sequence of numbers below.  
Bluetooth  
Search for audio accessories  
8910  
10  
2
4.  
5.  
Enter “0000” as the passcode then press OK. The volume level will be displayed. The  
phone is now connected with the Car Kit.  
Press Back then Exit to exit the Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Note: Once paired, the Car Kit and the phone have simultaneous connection with each other.  
(Keypad tones will be heard on the Car Kit every time keypad is pressed).  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
2.  
Press Menu. Scroll to Bluetooth, SELECT. Scroll to View paired devices, SELECT.  
Select the Car Kit and press OPTIONS. Scroll to Request conn. authorisation, SELECT.  
No, SELECT.  
3.  
Continue pressing Back to exit from Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Bluetooth  
View paired devices  
Select  
8910  
10  
4
Options  
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit as well as on the  
phone.  
1.  
2.  
Press the multi-function button down once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. As you dial, audio and the keypad tones can  
be heard on the Car Kit simultaneously but not on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Note: If the call is terminated using the cellular phone, a tone will be heard on the Car  
Kit indicating that the call has been terminated.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press quickly the multi-function button twice to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording for voice dialing.  
1.  
From standby mode, press arrow up or down.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
4.  
Find a contact name to which you want to add a voice tag. Press Details button. The  
phone number will be displayed.  
Press Options button. Add voice tag, SELECT. Press Start, and say the name clearly.  
Voice tag saved is displayed indicating that the voice tag has been saved.  
In case you wish to change your recorded voice, press Names, Voice tags, SELECT.  
Scroll to the name that you want to change the voice tag then press Options. Change,  
SELECT. Follow the instructions.  
5.  
Continue pressing Back button to exit.  
Note: Noisy environment could affect voice recognition. Record voice in a quiet environment.  
USING WITH NOKIA 8910i  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT.  
Choose On, SELECT. An icon will appear on the display on the standby mode.  
Continue pressing Back to exit from Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Bluetooth  
Select  
On  
Select  
8910i  
10  
1
1
1
1
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT and scroll to Search  
for audio accessories, SELECT. The phone is now searching for Bluetooth devices.  
SELECT the Car Kit. The phone will initiate connection with the Car Kit.  
QUICK ACCESS (for step 3):  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Bluetooth  
Search for audio accessories  
8910i  
10  
1
2
4.  
5.  
Enter “0000” as the passcode then press OK. The phone is now connected with the Car  
Kit.  
Continue pressing Back to exit from Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Note: Once paired, the Car Kit and the phone have simultaneous connection. (Keypad tones  
can be heard on the Car Kit every time the keypad is pressed).  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT. Scroll to View paired  
devices, SELECT.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
Select the Car Kit and press OPTIONS. Scroll to Request conn. authorisation, SELECT.  
No, SELECT.  
Continue pressing Back to exit from Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Bluetooth  
View paired devices  
Select  
8910i  
10  
1
4
Options  
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit as well as on the  
phone.  
1.  
2.  
Press the multi-function button down once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and Send. As you dial, audio and keypad tones are  
simultaneously heard on the Car Kit. No audio on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press twice quickly the multi-function button to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press twice quickly the multi-function button to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
From standby mode, press arrow up or down.  
Find a contact name to which you want to add a voice tag. Press Details button. The  
phone number will be displayed.  
3.  
4.  
Press Options button. Add voice tag, SELECT. Press Start, and say the name clearly.  
Voice tag saved is displayed indicating that the voice tag has been saved.  
In case you wish to change your recorded voice, press Names, Voice tags, SELECT.  
Scroll to the name that you want to change the voice tag then press Options. Change,  
SELECT. Follow the instructions.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.  
Continue pressing Back to exit.  
Note: Noisy environment could affect voice recognition. Record voice in a quiet environment.  
USING WITH NOKIA 3650  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Press Menu  
button. Scroll to Connect., OPTIONS. A list of options will be displayed.  
Choose OPEN then press SELECT. Choose Bluetooth, OPTIONS. Choose OPEN, and  
press SELECT.  
2.  
3.  
Bluetooth  
On, then press OK.  
Continue pressing Exit.  
OFF  
will be displayed. Press OPTIONS. Change, SELECT. Choose  
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu  
button. Scroll to Connect., OPTIONS. Choose Open, press SELECT.  
button, “Paired devices” will be  
Bluetooth, OPTIONS. Open, SELECT. Press  
displayed as title. Press OPTIONS. New paired device, SELECT. “Searching for  
devices…” will be displayed. Select the Car Kit and press SELECT. “Waiting for…” and  
“Passcode for…” will be displayed simultaneously.  
4.  
5.  
Enter “0000” as the passcode then press OK. “Waiting for…” and “Pairing  
with…complete” will be displayed simultaneously.  
Continue pressing Exit to get out of Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Note: Once paired, press the multi-function button once to establish simultaneous connection  
between the Car Kit and phone. (Keypad tones will then be heard on the Car Kit every time  
the keypad is pressed). If ever the paired device was deleted and turned off, when it is turned  
back on, there’s no need to undergo the same pairing procedure. “Passcode for…” will be  
displayed. Enter the passcode then press OK. “Accept connection request from…” press YES  
to reconnect.  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
Press Menu  
button. Scroll to Connect., OPTIONS. Choose Open, press SELECT.  
Bluetooth, OPTIONS. Open, SELECT. Press  
button. “Paired devices” will be  
displayed as title.  
2.  
3.  
Select the Car Kit and press OPTIONS. Scroll to Set as authorised, SELECT.  
“Connections will take place without confirmation. Continue?” press YES.  
Continue pressing Exit key to exit the Menu. An icon will then appear on the upper right  
corner.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, simultaneous ring tone will be heard on the Car Kit as well  
as on the phone.  
1.  
2.  
Press the multi-function button once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. As you dial, audio and the keypad tones can  
be heard on the Car Kit simultaneously but not on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Note: If the call is terminated using the cellular phone, a tone will be heard on the Car  
Kit indicating that the call has been terminated.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press twice quickly the multi-function button to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
3.  
Press Menu  
Find a contact name. Press  
Press Options button. Scroll to Add Voice tag, SELECT. Instructions appear. Your voice  
is automatically saved on the phone after being played back to you.  
In case you wish to change your recorded voice, press Options button. Voice tag,  
SELECT. Change, SELECT. Instructions appear.  
button. Select Contacts, OPTIONS. Open, SELECT.  
button. (The contact number is the one being displayed.)  
4.  
5.  
Continue pressing Exit key to get out of Menu.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING WITH NOKIA 6230  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Press Menu and select Settings, Connectivity and Bluetooth.  
Select Blue tooth on and On.  
Continue pressing Back then finally Exit.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Press Menu and select Settings, Connectivity and Bluetooth.  
Select Search for audio enhancements.  
The phone now searches for Bluetooth devices to be paired. When the search is  
complete, it displays the names of the devices found.  
Choose the device you want to pair with your phone, Select.  
Enter “0000” as the passcode then press ok.  
5.  
6.  
7.  
Continue pressing Back then finally Exit.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Notes:  
1. Once paired, keypad tones will be heard on the Car Kit.  
2. Pairing is done only once. When the Car Kit is turned off, then turned back on, it is  
automatically connected to the cellphone. That is, when you already activate the phone’s Auto  
Accept Mode. Kindly refer to “section c. AUTO ACCEPT MODE”.  
3. When the paired device is deleted, it can still be viewed as an active device and not yet  
completely disconnected. Thus, there will still be simultaneous connection between your Car  
Kit and cell phone even after deleting was done. But when you delete the pairing and at the  
same time, you disconnect it as an active device (That is, pressing “Disconn.”), you totally  
disconnect the bond.  
4. If ever the paired device was deleted and bond totally disconnected but you wish to pair it  
again, you need to undergo the same pairing procedure.  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
2.  
3.  
4.  
5.  
Press Menu and select Settings, Connectivity and Bluetooth.  
Select Paired devices. Choose the name of your device and press Options.  
Select Request conn. authorisation.  
Select No.  
Continue pressing Back then finally Exit.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, same ring tone will be heard simultaneously on the Car Kit  
as well as on the phone.  
1.  
Press the multi-function button once to answer the call.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.  
Pressing once again on the multi-function button will terminate the call.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
e.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and press CALL key. As you dial, audio and the keypad  
tones can be heard on the Car Kit, not on the phone.  
2.  
Press the multi-function button to terminate the call.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press once on the multi-function button to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of the  
person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place the  
call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the multi-function button again to terminate the call.  
Redialing  
Press twice quickly the multi-function button to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press the multi-function button twice quickly to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
3.  
Press Menu and select Contacts and Search.  
Choose the name which you want to make a voice dial then press Details.  
Press Options and select Add voice tag. Follow the instructions that are displayed.  
Your voice will then be saved on the phone after it is played back to you.  
Continue pressing Back then finally Exit.  
4.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
USING WITH NOKIA 6650  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT.  
BluetoothOff, SELECT. Choose On, SELECT. An icon will appear on the display on the  
standby mode.  
3.  
Continue pressing Back to exit from Menu.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Bluetooth  
BluetoothOff  
On  
Select  
6650  
11  
1
1
1
1
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT and scroll to Search  
for audio enhancements, SELECT. The phone is now searching for Bluetooth devices.  
SELECT the Car Kit. The phone will initiate connection with the Car Kit.  
QUICK ACCESS (for step 3):  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Blue tooth  
Search for audio accessories  
6650  
11  
1
2
4.  
5.  
Enter “0000” as the passcode then press OK. The phone is now connected with the Car  
Kit.  
Continue pressing the Back button to exit from Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Note: Once paired, the Car Kit and the phone have simultaneous connection with each other  
(keypad tones can be heard on the Car Kit every time the keypad is pressed).  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
2.  
3.  
Press Menu. Scroll to Connectivity, SELECT. Bluetooth, SELECT. Scroll to View paired  
devices, SELECT.  
Select the Car Kit and press OPTIONS. Scroll to Request conn. authorisation, SELECT.  
No, SELECT.  
Continue pressing Back button to exit the Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Connectivity  
Bluetooth  
View paired devices  
6650  
11  
1
4
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit as well as on the  
phone.  
1.  
2.  
Press the multi-function button once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the Car  
Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. As you dial, audio and the keypad tones can  
be heard on the Car Kit simultaneously but not on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A tone will then be heard on the Car Kit prompting the user to say the name of the  
person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press twice quickly the multi-function button to redial the last number.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
3.  
Press the Names button. Search, SELECT.  
Find a contact. Press Details button.  
Press Options button. Add voice tag, SELECT. Follow instructions on the cell phone.  
Your voice is automatically saved on the phone after being played back to you.  
In case you wish to change your recorded voice, press Options button. Voice tag,  
SELECT. Change, SELECT. Follow instructions on the cell phone.  
Continue pressing Back button to exit.  
4.  
5.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
USING WITH NOKIA 6600  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
Press the Menu  
of options will be displayed. Choose Bluetooth, press  
Bluetooth will be displayed. Press to switch Bluetooth On.  
Continue pressing Exit key to exit the Menu.  
key. Using the joystick, scroll to Connect., press  
to select. A list  
to select.  
2.  
3.  
OFF  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press the Menu  
list of options will be displayed. Choose Bluetooth, press  
press . “Paired devices” will be displayed as title. Press OPTIONS. New paired  
button. Using the joystick, scroll to Connect., press  
to select . A  
to select. Bluetooth  
ON  
device, SELECT. “Searching for devices…” will be displayed. Select the Car Kit and  
press SELECT. “Waiting for…” and “Passcode for…” will be displayed simultaneously.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.  
5.  
Enter “0000” as the passcode then press OK. “Waiting for…” and “Pairing  
with…complete” will be displayed simultaneously.  
Continue pressing Exit key to exit the Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
Note: Once paired, press the multi-function button once to establish simultaneous connection  
between the Car Kit and the phone (keypad tones can be heard on the Car Kit every time the  
keypad is pressed). If ever the paired device was deleted and turned off, once it is turned on,  
there is no need to undergo the same pairing procedure. Press the multi-function button once.  
“Passcode for…” will be displayed. Enter the passcode then press OK. “Accept connection  
request from…” press YES to reconnect.  
c.  
AUTO ACCEPT MODE  
The auto accept mode allows the Bluetooth function to be turned on automatically whenever  
the user starts sending information such as answering or making a call via the Bluetooth Car  
Kit.  
1.  
2.  
3.  
Press the Menu  
button. “Paired devices” will be displayed as title.  
Select the Car Kit and press . Scroll to Set as authorised, and press  
SELECT. “Connections will take place without confirmation. Continue?” press YES.  
Continue pressing Exit key to exit the Menu. An icon will then appear on the upper right  
corner.  
button. Scroll to Connect., press  
. Bluetooth, press  
. Press  
to  
d.  
e.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard on the Car Kit as well as on the  
phone.  
1.  
2.  
Press the multi-function button down once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call but audio will still be heard on the  
Car Kit.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and send. As you dial, audio and the keypad tones can  
be heard on the Car Kit simultaneously but not on the phone.  
2.  
Press the multi-function button to hang-up and terminate the call.  
Note: If the call is terminated using the cellular phone, a tone will be heard on the  
Car Kit indicating that the call has been terminated.  
Voice dialing  
Refer to step h for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the button again to terminate the call.  
Redialing  
Press quickly the multi-function button twice to redial the last number.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
g.  
h.  
REJECTING A CALL  
Press the multi-function button twice to reject the incoming call.  
RECORDING FOR VOICE DIALING  
Use your phone when recording voice dialing.  
1.  
2.  
3.  
Press the Menu  
Find a contact name. Press  
Press Options button. Scroll to Add Voice tag, SELECT. Instructions appear. Your voice  
is automatically saved on the phone after being played back to you.  
In case you wish to change your recorded voice, press Options button. Voice tag,  
SELECT. Change, SELECT. Instructions appear.  
button. Scroll to Contacts and press  
.
button. (The contact number is the one being displayed.)  
4.  
5.  
Continue pressing Exit key to get out of Menu.  
Note: Record your voice command in a quiet place so that only your voice will be recorded on  
the phone.  
USING WITH PANASONIC X70  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Go to Menu by pressing the center button of the 5-way navigation key featured as  
Scroll to Organizer, Select. Scroll to Connect, Select. Bluetooth, Select.  
On/Off, Select. Choose On, Select.  
.
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below.  
Organizer  
Connect  
Bluetooth  
On  
X70  
4. Continue pressing  
PAIRING TO THE CELLULAR PHONE  
8
9
1
Select  
to exit.  
b.  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
Go to Menu by pressing center button of  
Connect, Select. Bluetooth, Select.  
Choose Discover & Pair, Select.  
key. Scroll to Organizer, Select. Scroll to  
QUICK ACCESS (for steps 3 and 4):  
Press Menu followed by the sequence of numbers below.  
Organizer  
Connect  
Bluetooth  
Discover & Pair  
X70  
8
9
1
2
The phone is now searching for pairable devices to be added.  
5. Select the device you want to pair with your cell phone, and then press Pair.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.  
7.  
Enter “0000” as the passkey then press Ok. If the pairing is successful, the alternating  
red/blue lights will stop.  
Continue pressing to exit.  
The unit is now ready to link calls from the phone directly to the Car Kit. An icon appears  
during the standby mode indicating that the Car Kit is linked with the phone. If pairing is  
unsuccessful, the steps above may be repeated.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, two dissimilar ring tones will be heard on the phone and  
on the Car Kit.  
1.  
When answering is done on the Car Kit (that is, pressing the multi-function button once),  
the ongoing call can be heard from it.  
2.  
When answering is done on the phone, ongoing call can be heard from the phone (not  
on the Car Kit). But if you wish to hear and transfer the call to the Car Kit, just press  
once on the Car Kit’s multi-function button.  
3.  
To terminate the call, press down once on the multi-function button.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Using your phone, enter the contact number and press SEND key. Audio is heard  
on the phone and no immediate audio heard on the Car Kit yet. You have to press  
once on the multi-function button to transfer the audio to the Car Kit.  
To terminate the call, press down once on the multifunction button.  
2.  
Voice dialing  
Refer to step h and i for the procedure when activating and recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
Beep will then be heard on the Car Kit prompting the user to say the name of the  
person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cell phone does not recognize the name  
spoken, the steps above may be repeated.  
To terminate the call, press down the multifunction button once.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
e.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing down the multi-function button once or accessing the  
cell phone’s Menu during ongoing calls.  
f.  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
g.  
ACTIVATING THE VOICE DIALING  
Use your phone when recording for voice dialing. Before voice dialing, you must first turn on  
the Voice Dial function and record your voice. To turn voice dial on:  
1.  
2.  
3.  
4.  
Go to Menu by pressing  
On the Contacts List, choose Settings, Select.  
Choose Voice Dial, Select. Choose On and press Ok.  
key. Scroll to Contacts List, Select.  
Continue pressing  
to exit.  
h.  
RECORDING FOR VOICE DIALING  
1.  
2.  
Go to Menu by pressing  
On the Contacts List, scroll down to Voice Dial, Select.  
key. Scroll to Contacts List, Select.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
4.  
5.  
Press Menu. Choose Add, Select.  
On the contact names listed, choose the one you want to make a voice dial.  
After choosing a contact, press again center button of  
key. Choose Recall, Select.  
A statement “Please Record Your Voice!” appears. Press Ok.  
Follow the instructions on screen. Voice is then saved on the phone. Under Voice Dial  
list, the name which already has a voice command appears.  
6.  
7.  
Continue pressing  
to exit.  
Note: Noisy environment may affect voice recognition. Record your voice in a quiet  
environment.  
USING WITH Qtek 2020  
a.  
b.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your Pocket  
PC Phone and other Bluetooth devices.  
1.  
2.  
3.  
Tap . Scroll down to Settings. Tap Connections tab. Tap Bluetooth.  
Select On and tap ok.  
Tap V to exit.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring your PC phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
Press the multi-function button once again for a short time, to access headset  
pairing mode.  
4.  
5.  
Tap . Scroll down to Settings. Tap Connections tab. Tap Bluetooth.  
Tap Bonded Devices tab. Tap New.  
Your device now searches for Bluetooth devices and displays them in the list.  
Tap the name of the device that you want to bond with your PC phone, and then tap  
Next.  
6.  
7.  
8.  
9.  
Enter “0000” as the Device PIN and then tap Next.  
Tap Finish. (Note: In Name, you may or may not edit the name of your bonded device).  
For the question, “This Bluetooth device supports headset profile, would you like to set it  
as your Blue tooth headset?”, tap Yes tab.  
10. Tap ok, and then V to exit.  
The unit is now ready to link calls from the PC phone directly to the Car Kit. An icon appears  
during the standby mode indicating that the Car Kit is linked with the PC phone. If pairing is  
unsuccessful, the steps above may be repeated.  
c.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, two dissimilar ring tones will be heard on the phone and  
on the Car Kit.  
1.  
When answering is done on the Car Kit (that is, pressing the multi-function button once),  
the ongoing call can be heard from it.  
2.  
When answering is done on the phone, ongoing call can be heard from the phone (not  
on the Car Kit). But if you wish to hear and transfer the call to the Car Kit, just press  
once on the Car Kit’s multi-function button.  
3.  
To terminate the call, press down the multi-function button once.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
d.  
MAKING A CALL with the Car Kit on  
Normal dialing  
With your Pocket PC Phone, you can make a call using different methods. Please refer  
to your PC Phone’s User Guide.  
The most direct method is by using the Phone keypad.  
1.  
Press button to bring up the dialer screen.  
2.  
Tap the number on the keypad, and then tap  
Talk key.  
Note: Ongoing call will be heard on the phone and not immediately on the Car Kit. You  
have to press once on the Car Kit’s multi-function button to transfer the sound to the Car  
Kit.  
3.  
To terminate the call, press down the multifunction button once.  
e.  
a.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button once or accessing on the  
phone’s Bluetooth Headset ²icon.  
USING WITH SHARP GX32  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
3.  
Press  
to display Main Menu.  
Highlight Settings, and then press  
Succeedingly, highlight and select Connectivity, Bluetooth, Bluetooth On/Off and  
to select.  
On.  
4.  
Continue pressing Back then finally Exit.  
The Bluetooth setting is activated. Bluetooth icon is displayed on standby mode screen.  
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and at the same time, the Bluetooth indicator LED  
changes from blinking blue to alternate blinking of red and blue. This indicates that the  
unit is now ready for pairing.  
3.  
4.  
5.  
Press  
to display Main Menu.  
Highlight Settings, and then press  
to select.  
Succeedingly, highlight and select Connectivity, Bluetooth and Search for Devices.  
The phone displays three categories: “Headset”, “Car kit”, and “All”. Choose “Car Kit”.  
Note: If you select “All”, the phone lists devices from all categories.  
The phone now searches for Bluetooth devices to be paired. When the search is complete,  
devices found in the selected category are listed.  
6.  
7.  
8.  
Highlight the desired device for pairing, and then press  
Enter “0000” as the passcode then press ok.  
Continue pressing Back then finally Exit.  
to select.  
The Car Kit is paired and ready to use. Bluetooth icon  
mode.  
is displayed during the standby  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, two dissimilar tones will be heard on the Car Kit.  
1.  
When answering is done on the Car Kit, (that is, pressing the multi-function button  
once), the ongoing call can be heard from it.  
2.  
3.  
When answering is done on the phone, ongoing call can still be heard on the Car Kit.  
To terminate the call, press the multi-function button once.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Using your phone, enter the contact number and press Send key. Audio will be heard  
on the Car Kit. Note: If at times, when audio is heard on the phone, just press once on  
the multi-function button to transfer audio to the Car Kit.  
2.  
To terminate the call, press down the multi-function button once.  
Redialing  
Press the multi-function button twice quickly to redial the last number.  
e.  
f.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing down the multi-function button once or accessing the  
cell phone’s menu during ongoing calls.  
REJECTING A CALL  
Press the multi-function button twice quickly to reject an incoming call.  
USING WITH SIEMENS S55  
a.  
ACTIVATING THE BLUETOOTH  
You must activate your Bluetooth to establish a Bluetooth connection between your mobile  
phone and other Bluetooth devices.  
1.  
2.  
Press Menu button. Scroll to Setup, SELECT. Choose Connectivity, SELECT.  
Scroll to Bluetooth, Change. The phone is now connecting with the Bluetooth device.  
An icon will appear on the upper left corner when connected. OPTIONS button may also  
be pressed. Choose Activate BT, then SELECT.  
3.  
Continue pressing the On/Off/End Key to exit from Menu.  
QUICK ACCESS:  
Press Menu followed by the sequence of numbers below. Doing this sequence once will either  
activate or deactivate the Bluetooth depending on your current setting.  
Setup  
Connectivity  
Bluetooth  
9
6
4
b.  
PAIRING TO THE CELLULAR PHONE  
1.  
2.  
Bring the cellular phone at about 20 cm from the Car Kit.  
From the ON state, press the multi-function button for 10 seconds or until a distinctive  
three-tone sound will be heard and the same time, the Bluetooth indicator LED changes  
from blinking blue to alternate blinking of red and blue. This indicates that the unit is  
now ready for pairing.  
3.  
Press Menu button. Scroll to Setup, SELECT. Choose Connectivity, SELECT. Scroll to  
Bluetooth, OPTIONS. Scroll to Search for…, press ACCESS button. The phone is now  
searching for devices. When the search is complete, Devices disc. is displayed as title.  
If the device you are looking for is not on the list, repeat the procedure by pressing the  
OPTIONS and REPEAT buttons. Then press SELECT to add the device. The phone  
will initiate connection with the Car Kit.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.  
5.  
Pls, enter BT pin for…, OK. Enter “0000” as the BT pin then press OK. Handsfree  
trusted will be displayed afterwards indicating that the pairing is completed.  
Continue pressing the On/Off/End Key to exit from Menu.  
The Car Kit is paired and ready to use. An icon will be displayed during the standby mode  
indicating that the Car Kit is linked with the phone.  
c.  
d.  
ANSWERING/RECEIVING A CALL  
When the phone is receiving a call, a ring tone will be heard from the phone.  
1.  
2.  
Press the multi-function button once to answer the call.  
End the call by pressing the button again.  
Note: Cell phone buttons can also be used to answer a call. To transfer the call to the Car Kit,  
press the multi-function button once.  
MAKING A CALL with the Car Kit on  
Normal dialing  
1.  
Enter the contact number and Send. To transfer audio on the Car Kit, press the  
multi-function button once.  
2.  
Press the multi-function button again to hang-up and terminate the call.  
Note: If the call is terminated using the cellular phone, a tone will be heard on the Car  
Kit indicating that the call has been terminated.  
Voice dialing  
Refer to step g for the procedure when recording for voice dialing.  
1.  
2.  
Press the multi-function button once to activate the voice dialing.  
A beep will then be heard on the Car Kit prompting the user to say the name of  
the person to call.  
3.  
4.  
Say the name. The name will be played back to you. The phone will then place  
the call automatically. In case the cellular phone does not recognize the name  
spoken, the steps above may be repeated.  
Press the multi-function button again to terminate the call.  
Redialing  
Pressing quickly the multi-function button twice triggers the cell phone to redial the last  
number. Call is automatically transferred to the Car Kit.  
e.  
AUDIO TRANSFER  
Audio Transfer can be done by pressing the multi-function button or accessing the cell  
phone’s menu during ongoing calls.  
f.  
REJECTING THE CALL  
Press twice quickly multi-function button to reject the incoming call.  
g.  
RECORDING FOR VOICE DIALING  
Use your phone when recording for voice dialing. Record your contact names and numbers  
in the “Address book” (phone memory).  
1.  
From standby mode, open the Address book by pressing the arrow down key  
. (If  
Phone book is the one displayed, press  
Select a contact name. OPTIONS.  
Scroll to Voice dialing, SELECT. New, SELECT. Recording for: contact name, YES.  
Follow the instructions. Your voice is automatically saved on the phone after being  
played back to you.  
key to switch to Address book.)  
2.  
3.  
4.  
5.  
In case you wish to change your recorded voice, press Options button. Voice tags,  
SELECT. Change, SELECT. Instructions appear.  
Press On/Off/End key to exit  
Note: Noisy environment may affect voice recognition. Record your voice in a quiet place.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This equipment is in compliance with the essential requirements and other  
relevant provisions of Directive 1999/5/EC.  
Cet appareil est conforme aux exigences essentielles et aux autres  
dispositions pertinentes de la directive 1999/5/CE.  
Dieses Gerät befindet sich in Übereinstimmung mit den grundlegenden  
Anforderungen und den anderen relevanten Vorschriften der Richtlinie  
1999/5/EG.  
Che questo apparecchio è conforme ai requisiti essenziali ed alle altre  
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.  
El equipo cumple con los requisitos esenciales y cualesquiera otras  
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.  
Dit toestel is in overeenstemming met de essentiële eisen en de andere  
relevante bepalingen van richtlijn1999/5/EG.  
Este equipamento está conforme com os requisitos essenciais e outras  
disposições da Directiva 1999/5/CE.  
This equipment can be used in all European countries. An individual license is required in Romania.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shark Water Dispenser EP732F User Manual
Sony Computer Drive MSMT2G User Manual
Sony Digital Camera SRS U10 User Manual
Sony Microcassette Recorder ICD B25 User Manual
Sony Network Card PCWA C150S User Manual
Sony Projection Television KDF 55XS955 User Manual
Sony Stereo System CMT EH20DAB User Manual
Standard Horizon Marine RADAR MDS 1 User Manual
Subaru Automobile A3100BE User Manual
Sylvania DVD VCR Combo SSD800 User Manual