3-855-576-15(1)
DVD Recorder
Instructions For Use
DVO-1000MD
© 2005 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
Caution
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.
If you have any questions about this product, you may
call;
Sony Customer Information Service Center 1-800-222-
This DVD RECORDER is classified as a CLASS 1
LASER PRODUCT.
Declaration of Conformity
Trade Name:
SONY
Model:
Responsible Party:
Address:
DVO-1000MD
Caution
Sony Electronics Inc.
16530 Via Esprillo, San
Diego, CA 92127 U.S.A.
858-942-2230
The use of optical instruments with this product will
increase eye hazard.
Telephone Number:
Caution
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquid, such as vases,
shall be placed on the apparatus.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Important
The nameplate is located on the bottom.
For the customers in the U.S.A.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
For the customers in Canada
This unit has been certified according to Standard CSA
C22.2 NO.60601.1.
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Selecting Either NTSC or PAL Video Signal
When the Disc Becomes Full During Recording .
Using an SVRM-100A Remote Control Unit (Not
Searching for a Particular Image - Index Scanning
Cuing a Particular Image by Specifying an Index
Repeat Playback Between Two Points (A-B
4
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
On the panel display: HUMID!
Precautions
When the disc is being loaded in the unit
If you give a violent shock to the unit or move it with a
disc loaded because the unit is recording or playing
back, the disc may be damaged. Be sure to remove a disc
before moving the unit.
On safety
• Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be
used for an extended period of time.
• To disconnect the cord, pull it out by the plug. Never
pull the cord itself.
On cleaning
If the casing or panel is dirty, wipe it gently with a soft
dry cloth. In the event of extreme dirt, use a cloth
steeped in a neutral detergent to remove the dirt, then
wipe with a dry cloth. Applying alcohol, thinner,
insecticides, or other volatile solvents may result in
deforming the casing or damaging the finish.
On operation and storage location
Avoid operation or storage in any of the following
places.
• Location subject to extremes of temperature
(operating temperature range 5°C to 40°C (41°F to
104°F))
• Location subject to direct sunlight for long periods, or
close to heating appliances.
On repacking and shipping
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your
unit. For maximum protection, repack your unit as it was
originally packed at the factory, and take care not to
impact violent shocks in transit.
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating electromagnetic
emissions
• Location near transmitting stations generating strong
radio waves
• Location exposed to dripping or splashing. Do not put
objects filled with liquid, such as vases, on the unit.
Splashing the unit with liquid may cause a
malfunction.
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through
an excessive angel.
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent
shock to it, is likely to cause it to malfunction.
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilating openings, by for example wrapping the unit
in a cloth while it is in operation.
Condensation
If you move the unit from a very cold place to a warm
place, or use it in a damp location, condensation may
form on the optical pickup. Then, if the unit is operated
in this state, the unit does not record or play correctly.
When the power is turned on, the following message
appears, wait until it disappears before loading a disc.
On the monitor window: MOISTURE HAS BEEN
DETECTED.
5
Precautions
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyrights
• Materials played or recorded on this unit may be
copyrighted. Unauthorized recording of such material
may be contrary to the provisions of the copyright
laws. You cannot use those materials without
permission from the owners except for playing those
materials for personal use.
• This unit incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only, unless otherwise authorized
by Marcrivision. Reverse engineering or disassembly
is prohibited.
• Since this unit has a copy guard function, software and
broadcasting programs that contain copy protection
signals cannot be recorded on this unit.
• Since this unit has a function for prohibiting playback
of not-permitted discs such as pirated discs, you
cannot play such discs using this unit.
Exemption from responsibility for
compensation for recorded data
We will not take any responsibility for compensation for
data that could not be recorded or played due to
problems such as malfunction of the unit, corruption or
loss of recorded or edited data, or any losses caused by
such malfunctions or loss of data.
Please be aware of this policy beforehand.
Problems may occur if you perform the following
operations:
• When you use a disc recorded or edited using the unit
with another DVD recorder or the DVD drive of a
personal computer.
• When you attempt to re-use a disc with this unit, after
using it in the operations described above.
• When you use a disc recorded using another DVD
recorder or DVD drive of a personal computer with
this unit.
6
Copyrights
Download from Www.Somanuals.com. All Manuals Search And Download.
• Title list
Overview
You can display the list of titles recorded on the disc,
and using this list, you can search for the desired title
from which you can start playback on the list.
Variety of input/output interfaces
Features
Digital interfaces
This unit is equipped with an i.LINK connector so that
The DVO-1000MD is a DVD Recorder designed for use
with video equipment such as external equipment. The
DVO-1000MD compresses video signals sent from the
external equipment with an MPEG-2 format and audio
signals with Dolby Digital format (2CH), and records
video and audio signals on a DVD+RW disc.
1)
DV format digital video and audio signals can be input.
1) i.LINK and
are trademarks of Sony Corporation and indicate that
this product is in agreement with IEEE1394-1995 specifications and
their revisions.
The following are the principal features of the unit.
Analog interfaces
This unit can also use the following analog interfaces.
• Analog video
– Composite inputs (with loop-through)/output
– S-video inputs (with loop-through)/output
• Analog audio
1)
Rewritable DVD+RW disc as the
recording media
Since rewritable DVD+RW disc is used as a removable
disc, the disc is automatically finalized and discs
recorded with this unit can be played on other DVD+RW
players. Also, the unit searches for the first blank space
automatically and starts recording from that point. Thus,
it is not necessary to cue up and you can start recording
right after you insert the disc.
– 2-channel inputs/outputs
– Monitor output
Control interfaces
This unit is equipped with the following interfaces.
• RS-232C interface/USB interface
This unit is equipped with 9-pin RS-232C which is
compatible with the SVO-9500MD video cassette
recorder protocol and a USB interface which is
compatible with the RS-232C protocol. These
interfaces provide the following new functions in
addition to existing remote control functions of the
unit:
1)
is a trademark.
High-quality and long recording
The unit employs VBR (Variable Bit Rate) recording
which varies the compressed rate of MPEG2
dynamically according to the images recorded, thereby
high-quality recording relative to recording time can be
realized. Also, you can select picture quality from
among three recording modes: HQ (about 60 minutes:
CBR (Constant Bit Rate)), SP (about 120 minutes:
VBR) and LP (about 180 minutes: VBR).
– Meta data input/output per title
You can record meta data such as name, ID,
production date from external equipment for each
title.
– Input/output of updated data in real time
• i.LINK interface
Follows AV/C protocol
You can select one from among an RS-232C interface,
a USB interface, or an i.LINK interface from a menu.
• Control using the remote control unit
You can use the following remote control units.
– SVRM-100A remote control unit (not supplied)
Recording indexes
You can mark indexes during recording or playback.
This allows you to search for the desired points instantly
during playback, and also to play a segment specified by
two points repeatedly.
High-quality audio recording
1)
The Dolby Digital recording format allows you to
Compact size
The compact size of the unit makes the unit suitable for
use with medical instruments which are designed for use
in limited spaces.
record high-quality audio sound simultaneously with the
video signals.
1) The unit is manufactured under license from Dolby Laboratories.
“Dolby” and Double-D symbol are trademarks of Dolby Laboratories.
Playback using the quick search function
• Jumping to desired titles
• Jumping to the desired indexes
This allows you to search by indexes.
7
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
Front Panel
1 1 (Power) switch and standby indicator
2 Disc tray
3 OPEN/CLOSE button
7 Disc control section
8 Menu/disc control section
6 Front panel display
5 REMOTE 2 connector
4 REMOTE 1 connector
1 1 (power) switch and standby indicator
Press to power on the unit when the MAIN POWER
This causes the front panel display to light. Even if
this switch is set to off, the indicator is lit in green
when the MAIN POWER switch is set to on. To
power off the unit, press this switch again.
4 REMOTE 1 connector (stereo mini jack)
Connect a SVRM-100A remote control unit (not
supplied) to this connector for remote control.
5 REMOTE 2 connector (mini jack)
Connect a foot switch (not supplied) to this
connector. You can control recording and pausing
using this foot switch.
Note
If the MAIN POWER switch on the rear panel is
not set to on, the power is not on even if you press
the 1 (power) switch.
2 Disc tray
Used to insert or remove the disc.
3 OPEN/CLOSE button
Press to open or close the disc tray.
8
Location and Function of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Front panel display
F TITLE indicator
Indicates the number of the title which is being
recorded or played back.
A Disc indicator
G CHAP (chapter) indicator
B Recording mode indicator
C INPUT signal indicator
D Dolby indicator
Indicates the number of the chapter which is being
recorded or played back.
H Time indicator
E REPEAT indicator
F TITLE indicator
In normal operation, the elapsed time is displayed.
While recording, the elapsed time or the remaining
time of the disc is displayed according to the menu
SETUP MENU. When the remaining time of the
disc is selected, “REMAIN” is lit.
G CHAP indicator
H Time indicator
I Main display section
During menu operation or list operation, the
selected item is displayed.
I Main display section
If an abnormal operation occurs, an error code or
alarm message is displayed.
In this manual, menu operation is explained using
the monitor display. On the main display section of
the front panel display, the menu item currently
selected on the monitor display is lit.
A Disc indicator
Lights when a DVD+RW disc which can be
recorded and played back with this unit is loaded in
the tray. This indicator goes off when a disc tray
opens.
This indicator does not light when the disc which
cannot be used with this unit is loaded in the tray.
7 Disc control section
B Recording mode indicator
Indicates the recording mode.
While a disc is being played back, the recording
mode in which the disc was recorded is indicated.
When recording, the selected recording mode is
indicated. When a disc which has been recorded
using another DVD recorder is played, none of the
indicators light.
F zREC button
E XPAUSE button
D >NEXT/DOWN button
C BPLAY button
B .PREV/UP button
C INPUT signal indicator
A xSTOP button
Indicates the input signal currently selected.
Input connector
S-VIDEO IN
Indicator
S-VIDEO
VIDEO
A xSTOP button
VIDEO IN
Press this button to stop the recording or playback
operation.
DV IN (i.LINK)
i.LINK
D Dolby indicator
B .PREV/UP button
Goes out when an audio signal recorded in a format
other than in the Dolby Digital format is played
back.
PREV: Used to jump to a chapter.
When pressed once, moves to the start point of the
chapter currently being played back.
When pressed twice, moves to the start point of the
previous chapter.
Pressing this button with the BPLAY button held
down allows you to view fast reverse playback at a
speed three times the speed of the normal playback.
E REPEAT indicator
Lights during repeat playback.
For detailed information on repeated playback, see
9
Location and Function of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
UP: Used to go back to the previous page during
title operation in the TITLE LIST display.
Press this button to display the menu on the monitor
screen and the front panel display. Press it again to
exit the menu display.
C BPLAY button
When you press this button, it lights and playback
begins.
B LIST button
Press this button to display the TITLE LIST menu.
D >NEXT/DOWN button
C SET button
NEXT: Used to jump to a chapter.
Press this button to save new settings, such as
When pressed once, moves to the start point of the
selected menu items.
next chapter.
Pressing this button with the BPLAY button held
down allows you to view fast forward playback at a
speed three times the speed of the normal playback.
DOWN: Used to go to the next page during title
operation in the TITLE LIST display.
D V, v, B, b (cursor operation) buttons
Used to perform menu operation. Press these
buttons to select a menu item, to change numeric
values, and so on.
B and b buttons are also used to jump to the proper
point during playback operations.
E XPAUSE button
B button: When pressed once during playback,
jumps to the start point of the title currently being
played back. When pressed twice, jumps to the start
point of the previous title. When pressed with the
SET button during stopping, jumps to the beginning
of the first title in the disc.
During playback, press this button to pause the
playback operation. While paused, a still picture is
displayed.
Pressing this button again or pressing the BPLAY
button allows you to restart the playback operation.
During recording, press this button to pause the
recording operation. Pressing this button again
allows you to restart the recording operation.
b button: When pressed once during playback,
jumps to the start point of the next title. When
pressed with the SET button during stopping, jumps
to the beginning of the last chapter in the disc.
v (FREEZE) button: When pressed the first time
during playback, the picture becomes a frame
frozen picture. When pressed the second time, the
frame frozen picture is replaced with the frozen first
field picture. When pressed the third time, the first
field frozen picture is replaced with the second field
frozen picture. Whenever you press the v button,
the frozen picture is replaced in this sequence.
SETUP MENU allows you to decide whether the
first frozen picture is a frame frozen or field frozen
picture.
Note
During recording, each time you press the
XPAUSE button, indexes are automatically
marked.
F zREC button
When you press this button, this button lights and
recording begins.
8 Menu/disc control section
Note
The v button does not function as a FREEZE
button when the menu window or the TITLE LIST
window is displayed. In those windows, thie button
functions only as a cursor operation button.
D V, v, B, b buttons
C SET button
B LIST button
A MENU button
A MENU button
Used to enable the menu operation.
10
Location and Function of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
2 S-VIDEO IN connectors
3 VIDEO IN connectors
4 VIDEO OUT connector
1 MAIN POWER switch
5 S-VIDEO OUT connector
6 MONITOR AUDIO connector
qd -AC IN connector
7 AUDIO OUT L/R connectors
8 AUDIO IN L/R connectors
9 REMOTE IN RS-232C connector
0
DV IN (i.LINK) connector
qa
USB connector
qs
Equipotential ground terminal
connector
1 MAIN POWER switch
). Thus the same signals which are input to the
left connector are output from the right connector to
other equipment. When no connection is made to
the right connector, the left connector is terminated
automatically with an impedance of 75 Ω.
Switch to the = side to turn the power on. Switch to
the z side to turn the power off. Normally you
should leave this switch in the on position and
power the unit on and off with the power switch on
the front panel.
4 VIDEO OUT connector (BNC type)
This connector outputs analog composite video
signals.
Note
If you need to turn the main power off when not
using the unit for long periods and so on, always
power the unit off with the 1 (power) switch on the
front panel before setting this switch to off.
5 S-VIDEO OUT connector (4-pin mini DIN)
This connector outputs the analog S video signals.
6 MONITOR AUDIO connector (phono jack)
This connector outputs monaural audio signals for
monitoring.
2 S-VIDEO IN connectors (4-pin mini DIN)
The left S-VIDEO IN connector inputs analog S
video signals.
The audio signals to be output from this connector
can be selected among from audio channel 1, audio
channel 2, or mixed audio signals, using AUDIO
The two connectors are loop-through connectors. If
you connect S video input signals to the left
connector, you can bridge-connect the signal to
other equipment via the right connector (marked
). Thus the same signals which are input to the
left connector are output from the right connector to
other equipment. When no connection is made to
the right connector, the left connector is terminated
automatically with an impedance of 75 Ω.
7 AUDIO OUT L/R connectors (phono jack)
These connectors output analog audio signals.
8 AUDIO IN L/R connectors (phono jack)
These connectors input analog audio signals.
3 VIDEO IN connectors (BNC type)
The left VIDEO IN connector inputs analog
composite video signals.
9 REMOTE IN RS-232C connector (9-pin)
This is a 9-pin RS-232C interface which is
compatible with the SVO-9500MD video cassette
recorder protocol.
The two connectors are loop-through connectors. If
you connect composite video signals to the left
connector, you can bridge-connect the signal to
other equipment via the right connector (marked
11
Location and Function of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Use this connector to control this unit by
connecting it to equipment such as an external
equipment which supports the RS-232C interface.
0
qa
qs
DV IN (i.LINK) connector (6-pin)
This connector inputs digital video signals
conforming to the i.LINK protocol.
Also, this connector is used to control this unit by
connecting it to equipment such as an external
equipment which supports i.LINK.
USB connector
This connector is used to control this unit by
connecting it to equipment such as an external
equipment which supports a USB interface.
This connector is USB 2.0 which supports Full-
speed USB (12Mbps).
Equipotential ground terminal connector
This connector is used to connect to the
equipotential plug to bring the various parts of the
system to the same potential.
qd -AC IN connector
Use power cord suitable for your local power
supply (not supplied).
12
Location and Function of Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
• Connect the AC power cord last.
Notes
• Before making connections, be sure to turn the power
of any peripheral equipment off.
Connecting External Equipment (1)
This section gives a connection example to operate the
unit connected to external equipment using a remote
control unit (not supplied) and/or foot switch (not
supplied).
– LCH: Outputs the audio signal of audio channel 1.
– RCH: Outputs the audio signal of audio channel 2.
– MIX: Outputs a mixed audio signal from both
channel 1 and channel 2. (factory setting)
• Input signal selection
Select the input signal “ANALOG” using the INPUT
• Foot switch mode selection
Settings required for using this connection
example
Make the following settings before operating in this
connection example using SETUP MENU.
Select the operation mode of the foot switch from
among LOW EDGE (factory setting), HIGH EDGE
• Audio output selection
Select the audio output channel using the AUDIO
1
S-video cable (not supplied)
To S-video output connector
1
External equipment
2
To analog audio output connector
2
Audio cable (not supplied)
3
Audio cable (not supplied)
4
AUIDO IN L/R
AC power cord (not supplied)
Rear panel
To S-video input connector
1
Video monitor
S-VIDEO IN
S-VIDEO OUT
3
To analog audio input connector
MONITOR AUDIO
4
- AC IN
Front panel
SVRM-100A remote
control unit
to AC outlet
REMOTE 1
REMOTE 2
Foot switch
13
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting External Equipment (2)
This section gives an example to connect external
equipment for controlling the unit from connected
external equipment
– RCH: Outputs the audio signal of audio channel 2.
– MIX: Outputs a mixed audio signal from both
channel 1 and channel 2. (factory setting)
• Input signal selection
Select the input signal “ANALOG” using the INPUT
• Remote control mode selection
Select an interface to control the unit from among
RS232C (factory setting), USB and iLINK (see
Settings required for using this connection
example
Make the following settings before operating in this
connection example using SETUP MENU.
• Audio output selection
When controlling the unit, only one interface is
available from among RS232C (factory setting), USB
and iLINK.
Select the audio output channel using the AUDIO
– LCH: Outputs the audio signal of audio channel 1.
5
6
1
DV cable (not supplied)
USB cable (not supplied)
S-video cable (not supplied)
2
Audio cable (not supplied)
7
3
AC power cable (not supplied)
Audio cable (not supplied)
4
Video monitor
RS-232C cable (cross type/not supplied)
To S-video input connector
To analog audio input connector
1
AUDIO IN L/R
S-VIDEO IN
2
3
1
To analog audio
output connector
To S-video
output connector
S-VIDEO OUT
MONITOR AUDIO
7
- AC IN
to AC outlet
External equipment
to RS-232C connector
to DV connector
REMOTE IN RS-232C
DV IN (i.LINK)
USB
4
5
6
to USB connector
Note
You can use only one interface from among RS-232C, USB and
iLINK interfaces to control the unit remotely.
14
Connection
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Push the 1 (power) switch on the front panel to put
the unit in the standby mode.
Turning the Power On/
Off
Set the MAIN POWER switch on the rear panel to
the z (off) side.
The standby indicator on the front panel goes off
and the power is turned off.
Turning the Power On
Rear panel
1
AC power cord (to AC outlet)
Front panel
Standby indicator
2
1
2
Connect the AC power cord (not supplied) to the
wall outlet, and then set the MAIN POWER switch
located on the rear panel to the [ (on) side.
The standby indicator on the front panel lights in
green.
Push the 1 (power) switch on the front panel.
The power of the unit is turned on and the front
panel display lights. The message “Welcome”
appears on the front panel display. Then, the
message changes to “Now loading...” When the
message changes finally to “NO DISC!,” you can
start the next operation.
When a disc is loaded in the unit, “0101 0:00:00” is
displayed instead of “NO DISC!.”
To turn the power on or off during normal
operations
Turn the power on or off using the 1 (power) switch on
the front panel.
When you push the 1 (power) switch again, “Good
Bye” appears on the front panel display and then the
front panel display goes off and the power is turned off.
Then, the unit turns to the standby mode.
Turning the Power Off
If you do not intend to use the unit for a long period, turn
the main power of the unit off.
15
Turning the Power On/Off
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the proper video signal system corresponding to
the one used in your area.
Setup Preparation
Before you start to use the unit after you have made the
required connections, it is necessary to perform the
following operations.
10
11,12
1
• Selecting either NTSC or PAL video signal system
Select the video signal system used in your region.
• Setting the date and time
You should set the date and time when you start the
unit for the first time.
• Selecting the remote interface
2,4,9
3,5,6,8
4,6,7
Select the remote interface to be used to control the
unit remotely. At the factory, RS232C is selected as
the default. If you want to use either USB or i.LINK,
change the remote interface setting.
1
Press the MENU button.
The TOP menu appears.
Selecting Either NTSC or PAL Video
Signal System
When you use the unit for the first time, you should
select the video signal system. The TV SYSTEM sub
menu of the ENHANCED MENU of the SETUP MENU
allows you to select either the NTSC or PAL video
signal system.
For detailed information on menu operations, see
Note
2
Select “SETUP MENU” by pressing the V or v
At the factory setting, the NTSC video signal is selected
as the default. Even if your monitor does not correspond
to the video signal system currently selected, you can
carry out the menu operations using the main display
section of the front panel display.
button.
“SETUP MENU” is highlighted.
3
Press the b button.
16
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
The SETUP MENU appears.
The following display appears when enhanced
menu items have been added under the last item of
the basic setup menu.
4
Select “MENU GRADE” from the SETUP MENU
display.
7
8
Select “TV SYSTEM” by pressing the v button.
Each time you press the v or V button, the
highlighted cursor moves down or up item by item.
When the highlighted cursor reaches the last item
“KEY INHIBIT,” press the v button again. The
next page of the SETUP MENU appears.
Press the v button several times until “MENU
GRADE” is highlighted.
Press the b button.
The TV SYSTEM sub menu appears.
5
Press the b button.
The following display appears.
9
Select the desired video signal system by pressing
the V or v button.
The selected video signal system is highlighted.
TV SYSTEM
Content
NTSC
To record or play back with the
NTSC video signal system. (Factory
setting)
PAL
To record or play back with the PAL
video signal system.
6
Select “ENHANCED” by pressing the v button.
Then, with “ENHANCED” highlighted, press the B
button.
10 Press the SET button.
17
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
The message “NOW SAVING....” appears and the
unit starts to save the setting.
The TOP menu appears.
When saving is completed, the message disappears.
Then, “TV SYSTEM WAS CHANGED PLEASE
POWER OFF.” appears on the monitor display, and
“POWER OFF!” appears on the front panel display.
Note
The TV system is not changed even if you push the
SET button. Be sure to turn the power of the unit off
and on as described in steps 11 and 12 to change the
system.
2
Select “SETUP MENU” by pressing the V or v
button.
11 Press the 1 (power) switch on the front panel to
turn the power off.
“SETUP MENU” is highlighted.
The message “Good Bye” appears on the front
panel display. Then, the front panel display goes
off, the power is turned off and the unit enters the
standby mode.
12 Press the 1 (power) switch again to turn the power
on.
Setting the Date and Time
The DATE/TIME PRESET sub menu of the SETUP
MENU allows you to set the date and time.
3
Press the b button.
The SETUP MENU appears.
9
1
2,7
4
4
Select “DATE/TIME PRESET” from the SETUP
MENU display.
6
3,5
Each time you press the v or V button, the
highlighted cursor moves down or up one by one.
When the highlighted cursor reaches the last item
pressing the v button, press the v button again. The
next page of the SETUP MENU appears.
1
Press the MENU button.
18
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the v button several times until “DATE/TIME
PRESET” is highlighted.
you press the B button, the rightmost digit of the
date column is highlighted.
Front panel display during menu operation
The date column appears when you set the date in
the date column on the DATE/TIME PRESET sub
menu. And the time column appears when you set
the time in the time column.
7
Change the numeric value by pressing the V or v
button.
Press the V button to increase a value.
Press the v button to decrease a value.
5
Press the b button.
8
9
Set the remaining date and time values by repeating
steps 6 and 7.
The DATE/TIME PRESET sub menu appears.
Press the SET button when you have completed
setting the date and time.
The date and time values set are executed.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
To cancel the date/time setting without
changing any values
Press the MENU button. The unit returns to the (2/
2) or (2/3) SETUP MENU display one level higher
than the current one. The setting is cancelled. Press
the MENU button again. The unit exits the menu
display and returns to the normal display.
6
Select the digit to be set by pressing the B or b
button.
Press the B or b button until the digit you want to
change is highlighted.
Date display (month/date/year)
Highlighted display (digit to be
changed)
Note
In this case, the message “ABORT!’ will not
appear.
Time display
To move the cursor between the date
column and the time column
If you press the b button when the rightmost digit
of the date column is highlighted, the leftmost digit
of the time column is highlighted. When the
leftmost digit of the time column is highlighted, if
19
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
The SETUP MENU appears.
Selecting the Remote Interface
The REMOTE I/F sub menu of the SETUP MENU
allows you to select the interface to be used to control
the unit remotely.
The factory setting is RS-232C.
7
1
4
5
Select “REMOTE I/F” by pressing the v button.
2,4,6
3,5
1
Press the MENU button.
The TOP menu appears.
Press the b button.
The REMOTE I/F sub menu appears.
2
Select “SETUP MENU” by pressing the V or v
button.
6
Select the desired remote interface by pressing the
V or v button.
“SETUP MENU” is highlighted.
The selected remote interface is highlighted.
Item
Interface
RS232C
To control the unit from external
equipment connected to the RS-
232C connector. (Factory setting)
a)
iLINK
USB
To control the unit from external
equipment connected to the i.LINK
connector.
b)
To control the unit from external
equipment connected to the USB
c)
connector.
3
Press the b button.
20
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
a) This protocol is compatible with the SVO-
9500MD video cassette recorder protocol.
b) This setting is not related to the setting for the
input signal.
c) This protocol is equivalent to the RS-232C
protocol.
7
Press the SET button.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
The remote interface setting of the unit is set to the
one selected in step 6.
21
Setup Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Recording
• Do not store discs where they may be subjected to
direct sunlight, or in other places where the
temperature or humidity is high.
• Store discs in their cases.
• Finger prints or dust accumulated on the disc cause
deterioration of picture quality. Keep the disc clean.
Handling Discs
Care of the discs
• Clean the disc with a soft cloth, wiping it from the
center out. If the dust is heavy, wipe it with a soft cloth
moistened with water, then wipe off the water with a
dry cloth.
Usable Discs
You can use the DVD+RW discs corresponding to quad
speed.
Note
You can use discs for both data and video.
Formatting discs
An unused disc requires no formatting operation. The
disc is automatically formatted when loaded into the
unit.
When you use a disc formatted by a computer or
recorded by using other DVD equipment, format the
disc using the FORMAT sub menu of DISC INFO.
• Do not use solvents such as benzene, thinner,
commercially available record cleaners, or anti-static
spray. Using these products may damage discs.
Loading and Unloading Discs
Note
When a recorded disc is formatted, all the data on the
disc is erased.
For detailed information on how to format a disc, see
Loading a disc
1
2,4
3
Notes on Handling
Handling
• Do not touch the recording or playback surface of the
disc. Handle the disc by its edge.
• Do not use the following types of disc. Doing so may
cause the unit to malfunction.
– A disc on which a paper label or a seal is attached
– A disc on which the glue of cellophane tape or a
label, or on which a portion of a label still remains
– A cracked disc
1
Press the 1 (power) switch to turn the power on.
The message “Welcome” appears on the front panel
display.
The message changes to “Now loading...,” and then
“NO DISC!” lights. Proceed to the next operation.
– A cracked disc which has been mended using glue
(or a similar substance)
Note
If the 1 (power) is not turned on and the front panel
display does not light even if you press the power
22
Handling Discs
Download from Www.Somanuals.com. All Manuals Search And Download.
switch, check whether the MAIN POWER switch
on the rear panel is set to the ] (on) side.
For detailed information on how to turn the power
on or off, see “Turning the Power On/Off” on page
Unloading a disc
1
Press the OPEN/CLOSE button with the power
turned on.
The disc tray opens.
2
3
Press the OPEN/CLOSE button.
2
3
Remove the disc.
The disc tray opens.
The message changes to “OPEN” on the front panel
display.
If you do not wish to load another disc, press the
OPEN/CLOSE button to close the disc tray.
Place the disc on the tray.
With the recording/playback surface facing
down
4
Press the OPEN/CLOSE button. Or push the disc
tray lightly.
The disc tray closes.
The DISC IN display blinks and the message “Now
loading...” appears on the front panel display.
DISC IN display
Go to the next step, after the message “Now
loading...” disappears and the DISC IN display
stops blinking.
If you load discs which cannot be used with the
unit
The message “Not Supported!” appears.
In such a case, unload the disc and insert a disc that can
be used with the unit.
23
Handling Discs
Download from Www.Somanuals.com. All Manuals Search And Download.
The SETUP MENU appears.
Preparations for
Recording
Selecting Input Signals
The INPUT SELECT sub menu of SETUP MENU
allows you to select the input signal to be recorded.
1
6
3
4
Select “INPUT SELECT” by pressing the V or v
button.
2,4
2,3,5
Press the b button.
1
2
Press the MENU button.
The TOP menu appears.
The INPUT SELECT sub menu appears.
Select “SETUP MENU” by pressing the V or v
button and press the b button with “SETUP
MENU” highlighted.
5
Select the desired input signal by pressing the V or
v button.
Input signal
Setting
ANALOG
To record an analog signal input to
the VIDEO IN or S-VIDEO IN
connector. (Factory setting)
i.LINK
To record a standard DV digital
signal input to the DV IN (i.LINK)
connector.
When an analog input signal is selected:
When an S video cable is connected to the S-
VIDEO IN connector of the unit, the S video signal
is selected regardless of whether an S video signal
24
Preparations for Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
is input or not, taking precedence over a composite
video signal input to the VIDEO IN connector.
“S-VIDEO” appears on the front panel display.
2
Select “SETUP MENU” by pressing the V or v
button and press the b button with “SETUP
MENU” highlighted.
6
Press the SET button.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
The input signal is executed.
Selecting the Recording Mode
The SETUP MENU appears.
The unit employs three different recording modes.
The REC MODE sub menu of SETUP MENU allows
you to select the recording mode.
5
1
3
Confirm that the REC MODE is highlighted and
press the b button.
The REC MODE sub menu appears.
3
2,4
1
Press the MENU button.
The TOP menu appears.
4
5
Select the desired recording mode pressing the V or
v button.
Recording Setting
mode
Maximum
recording
time
HQ
SP
To record in high-quality About 1 hour
recording mode.
To record in standard
mode. (factory setting)
About 2 hours
LP
To record for long time.
About 3 hours
Press the SET button.
25
Preparations for Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
Recording
The unit allows you to record up to 49 titles on one disc.
Also, you can mark indexes at desired points during
recording.
The recording mode is executed.
When you record additional data on an already recorded
disc, the unit starts from the beginning of the blank
portion of the disc.
Notes
• If you load a disc which is full, a disc on which 49
titles have already been recorded, and so on, you
cannot record any data. Be sure to confirm the disc
before using it.
• When the remaining time of the disc becomes five
minutes, the main display section of the front panel
display (TITLE/CHAP/time indicator) blinks.
• Before performing the important recording, be sure to
try to record whether or not the unit records correctly.
Recording Titles
3
2,4
1
6
5
1
Press the 1 (power) switch to turn the power on.
The message “Welcome” appears on the front
panel.
When the message changes to “Now loading...,”
and then to “NO DISC!,” go to the next operation.
Note
If the power is not turned on and the front panel
display does not light even if you press the 1
(power) switch, check whether the MAIN POWER
switch on the rear panel is set to the ] (on) side.
26
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
For detailed information on how to turn the power
on or off, see “Turning the Power On/Off” on page
The titles are numbered in the sequence they are
recorded.
Title 2
Title 1
Title 3
2
3
Press the OPEN/CLOSE button.
The disc tray opens.
The message changes to “OPEN” on the front panel
display.
Recording
stops
Recording
stops
Recording
stops
Recording
starts
Recording
starts
Recording
starts
Place the disc on the tray.
To pause during recording
Press the XPAUSE button.
To resume recording, press the XPAUSE button again.
Notes
• At the beginning of recording, an index is marked
automatically. Also, indexes are marked whenever
you press the XPAUSE button.
• When the unit is remotely controlled with the RS-
232C remote interface, the STOP command works as
the pause task or stop recording task. Which task is
effective depends on the setting of the 232C STOP
SETUP MENU.
With the recording/playback surface facing
down
If buttons on the front panel do not
function even if you push them
MENU is set to “ON.”
Thus, the key-lock function is activated so that all
buttons except the MENU button, the LIST button, the
power switch, and the OPEN/CLOSE button are
deactivated to prevent you from pressing buttons
accidentally.
4
5
Press the OPEN/CLOSE button. Or push the disc
tray lightly.
The disc tray closes.
The DISC IN display blinks and the message “Now
loading...” appears on the front panel display.
When the DISC IN display stops blinking, go to
step 5.
To re-activate the buttons, set the KEY INHIBIT item to
“OFF.”
Press the zREC button.
However, when the unit is in menu operation status, you
can use the B, b, V, v, and SET buttons.
The unit starts recording of one title.
6
7
To stop recording that title, press the xSTOP
button.
Marking Indexes During Recording
Repeat recording of the remaining titles by
repeating steps 5 and 6.
You can mark indexes at desired points during
recording. This allows you to search for the desired
points instantly during playback, and also to play a
segment specified by two points in succession.
You can mark up to 254 indexes on one disc and up to 99
indexes within one title.
You can mark indexes using the following three
methods.
To use the XPAUSE button of the unit
Press the XPAUSE button on the front panel of the unit.
27
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the SVRM-100A remote control unit
Press the MARK button on the SVRM-100A remote
control unit (not supplied).
The TOP menu appears.
For detailed information on how to mark indexes, see
To mark indexes automatically
Indexes are automatically marked every five minutes
SETUP MENU is set to ON.
Note
You can mark up to 254 indexes on one disc and up to 99
indexes within one title.
When the number of indexes exceed the above
limitation, an alarm message appears.
For detailed information on alarm messages, see
2
Select “SETUP MENU” by pressing the V or v
button and press the b button with “SETUP
MENU” highlighted.
The SETUP MENU appears.
To make new titles automatically
The AUTO TITLE sub menu of the SETUP MENU
allows you to make a new title when the number of
indexes in one title exceeds 99.
Segment between the indexes
The segment between the indexes is called a chapter.
Title 3
Chapter 3 Chapter1 Chapter 2 Chapter1
Title 1
Title 2
3
4
Select “FOOT SW” by pressing the V or v button.
Chapter1
Chapter 2
Indexes
Using a Foot Switch
A foot switch (not supplied) allows you to start or pause
recording.
The operation required for starting or pausing the
recording depends on the setting of the FOOT SW sub
menu of the SETUP MENU.
Press the b button.
The FOOT SW sub menu appears.
Note
To stop recording when using a foot switch, press the
xSTOP button on the front panel of the unit.
1
Press the MENU button.
28
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Select the desired mode by pressing the V or v
button.
Notes
• Be sure to turn off the power of the unit by using the
1 (power) switch on the front panel of the unit.
For detailed information on how to turn off the power
• When not using the RM-P110, be sure to set the
KEYBOARD sub menu of the SETUP MENU to OFF
Mode
Setting
LOW EDGE
To start recording when you push
the foot switch, or to pause
recording during recording.
Even if you release the foot switch,
the recording or pause recording
status remains in effective. (Factory
setting)
To add information to the title or edit title
information
The TITLE INFO display of the title menu allows you to
edit title information.
HIGH EDGE
To start recording when you push
the foot switch and release it, or to
pause recording during recording.
The unit does not change from one
operation to another when you push
the foot switch.
Title name
LOW ACTIVE
While you hold the foot switch
down, the unit records. When you
release the foot switch, the unit
pauses.
6
Press the SET button.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
Title information (data of 2048 bytes)
When you record using equipment such as external
equipment, data is recorded via the communication
protocol.
Adding Information to Titles
When you record data, the recording month/date/year/
hour/minute/second (example: 01/06/04 17:25:19) is
recorded automatically.
Also, the RM-P110 remote control unit (not supplied)
allows you to change the title name and to record data of
2048 bytes every title using the keyboard of the RM-
P110. Thus, you can record additional information for a
title.
Pre Rec Function
When the PRE REC sub menu of the SETUP is set to
“ON,” the unit saves the last 5 seconds of video data in
the inernal memory. This function allows the unit to start
recording the last 5 seconds of video data saved
previously for continuity.
To use an RM-P110 (not supplied) as a
keyboard for editing/adding title name and
information
You should carry out the following operation and menu
settings:
• Connect the RM-P110 to the RS-232C connector of
the unit.
1
Press the MENU button.
SETUP MENU to RS232C.
SETUP MENU to ON.
You can enter characters in overwrite mode. Use the
ESC key for the backspace function.
29
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
The TOP menu appears.
5
6
Select the desired mode by pressing the V or v
button.
Mode
Setting
OFF
To record the video signal promptly
after you start recording. (Factory
setting)
ON
To start recording using the last 5
seconds of video data saved
previously.
Press the SET button.
2
Select “SETUP MENU” by pressing the V or v
button, and press the b button with “SETUP
MENU” highlighted.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
The SETUP MENU appears.
The setting for the previous recording is executed.
When the Disc Becomes Full
During Recording
At the factory setting, the unit stops recording
automatically and the disc tray opens.
The DISC END sub menu of the SETUP MENU allows
you to change this setting.
1
Press the MENU button.
The TOP menu appears.
3
4
Select “PRE REC” by pressing the V or v button.
Press the b button.
2
Select “SETUP MENU” by pressing the V or v
button and press the b button with “SETUP
MENU” highlighted.
The PRE REC sub menu appears.
30
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
The SETUP MENU appears.
The message “NOW SAVING...” appears and the
unit starts to save the setting.
When the saving is completed, the message
disappears and the unit returns to the normal
display.
The setting is executed.
3
4
Select “DISC END” by pressing the V or v button.
Press the b button.
The DISC END sub menu appears.
5
Select the desired disc end mode by pressing the V
or v button.
Mode
Setting
GOTO TOP
To return to the beginning of the
disc.
END STOP
To return to the beginning of the last
title, and end recording
automatically. However, the disc is
not ejected, and the disc remains in
the tray.
EJECT
To stop recording and eject the disc
automatically. (Factory setting)
6
Press the SET button.
31
Recording
Download from Www.Somanuals.com. All Manuals Search And Download.
The FINALIZE display appears.
Finalizing a Disc
There is a case where a disc recorded on this unit must
be finalized to play it on other equipment compatible
with DVD+RW equipment. Proceed as follows to
finalize the disc.
Even if the disc is finalized, you can use that disc for
recording again or you can edit data recorded on the
disc.
1
2
Load the disc to be finalized into the unit.
Press the MENU button.
The TOP menu appears.
5
6
Select “EXEC” pressing the V or v button. Then,
press the SET button.
The message “READY?” appears.
Press the SET button.
The message “FINALIZING THE DISC. PLEASE
WAIT.” appears, and finalization is started.
When finalization is completed, the message
changes to “COMPLETE!,” and the unit exits the
menu and returns to the normal display.
3
Select “DISC INFO” by pressing the V or v button,
and press the b button with “DISC INFO”
highlighted.
7
Remove the disc.
The DISC INFORMATION sub menu appears.
4
Press the V or v button to select “FINALIZE” and
press the b button with “FINALIZE” highlighted.
32
Finalizing a Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
The FORMAT display appears.
Formatting a Disc
You can erase all the data recorded on the DVD+RW
disc and format that disc so as to be able to use it with
the unit.
Note
When a recorded disc is formatted, all the data, such as
title names is erased. You cannot resume it to the status
before formatted.
1
2
Load the disc to be formatted in the unit.
Press the MENU button.
5
Select “EXEC” by pressing the V or v button, and
then press the SET button.
The message “READY?” appears.
The TOP menu appears.
To quit formatting a disc
Select “ESC,” and then press the SET button with
ESC highlighted.
Or press the MENU button.
6
7
Press the SET button.
The message “FORMATTING THE DISC.
PLEASE WAIT.” appears and formatting is started.
When formatting is completed, the message
changes to “COMPLETE!,” and the unit exits the
menu and returns to the normal display.
3
Select “DISC INFO” by pressing the V or v button,
and press the b button with “DISC INFO”
highlighted.
Remove the disc.
The DISC INFORMATION sub menu appears.
4
Select “FORMAT” by pressing the V or v button,
and press the b button with “FORMAT”
highlighted.
33
Formatting a Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press the OPEN/CLOSE button.
Playback
The disc tray opens.
The message changes to “OPEN” on the front panel
display.
Playback
3
4
Place the disc to be played on the tray.
Press the OPEN/CLOSE button.
Usable Discs
You can use the 4 x DVD+RW discs.
The disc tray closes.
The DISC IN display blinks and the message “Now
loading...” appears on the front panel display.
Go to step 5, after the message Now loading...”
disappears and the DISC IN display lights up.
Note
The recorded discs may not be able to be played back
due to scratch on the disc, dust accumulated on the disc,
conditions recorded or recording equipment.
5
Press the BPLAY button.
Playback starts.
Note
Playback a Disc
For a moment, the picture is frozen and audio
playback stops between titles.
3
1
2,4
To stop playback
Press the xSTOP button.
Fast Forward or Reverse Playback
To view fast forward playback
Press the >NEXT/DOWN button with the BPLAY
button held down. This allows you to view fast forward
playback at a speed three times the speed of normal
playback.
5
To view reverse playback
xSTOP button
Press the .PREV/UP button with the BPLAY button
held down. This allows you to view fast reverse
playback at a speed three times the speed of normal
playback.
1
Press the 1 (power) switch to turn the power on.
The message “Welcome” appears on the front
panel.
When the message changes to “Now loading...”,
and then to “NO DISC!.”, go to the next operation.
Adding Indexes During Playback
You can add indexes using the SVRM-100A remote
control unit.
For detailed information on how to add indexes, see
Note
If the power is not turned on and the front panel
display does not light even if you press the 1
(power) switch, check whether the MAIN POWER
switch on the rear panel is set to the ] (on) side.
For detailed information on how to turn the power
on or off, see “Turning the Power On/Off” on page
15.
34
Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Jumping to a Desired Chapter
The .PREV/UP or >NEXT/DOWN button
allows the unit to jump to the chapter before or after the
chapter currently being played.
Searching for Desired
Point
Jumping to a Desired Title
The B or b button allows the unit to jump to the title
before or after the title currently being played.
>NEXT/DOWN button
.PREV/UP button
When you use the >NEXT/DOWN button:
When you press this button once, the unit jumps to the
start point of the next chapter.
2
1
When you use the .PREV/UP button:
When you press this button once, the unit jumps to the
start point of the chapter currently being played.
When you press this button twice, the unit jumps to the
start point of the previous chapter.
1
2
Press the BPLAY button.
Playback starts.
Press the B or b button to jump.
When you press the B button:
Example
When you press this button once, the unit jumps to
the start point of the title currently being played.
When you press this button twice, the unit jumps to
the start point of the previous title of the title
currently being played.
Playback direction
A
B
C
D
a)
Chapter 1
Chapter 3
Chapter 2
PREV
Chapter 4
When you press the b button:
When you press this button once, the unit jumps to
the start point of the next title.
NEXT
P
a) The last chapter recorded on a disc
When you press the .PREV/UP button or the
>NEXT/DOWN button at the current position (point
P), the unit behaves as follows:
When the .PREV/UP button is pressed once: Jumps
to point C.
When the .PREV/UP button is pressed twice: Jumps
to point B.
When the >NEXT/DOWN button is pressed once:
Jumps to point D.
35
Searching for Desired Point
Download from Www.Somanuals.com. All Manuals Search And Download.
When the >NEXT/DOWN button is pressed twice:
When the target point is the end of the last chapter, the
unit jumps to the beginning of the last chapter. Thus, in
this case, the unit jumps to point D.
Repeat Playback
You can conduct the following repeat playback
operations using the menu.
• Repeat playback between two points (A-B repeat)
• Repeat playback of the chapter currently being played
• Repeat playback of the title currently being played
Repeat Playback Between Two
Points (A-B Repeat)
You can conduct repeat playback of a certain section
specified by two points.
Setting points A and B
Proceed as follows to set points A and B and conduct
repeat playback.
1
2
Load the disc to be played.
Press the MENU button during playback.
The TOP menu appears.
3
Select “REPEAT FUNCTION” by pressing the V
or v button, and press the b button with “REPEAT
FUNCTION” highlighted.
The REPEAT FUNCTION display appears.
4
Select “REPEAT A-B” by pressing the V or v
button, and press the b button with “REPEAT A-B”
highlighted.
36
Repeat Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Point A is set and “A” disappears. Then, “B” is
displayed as a white letter.
The REPEAT A-B display appears.
Select “A-B SET” by pressing the v button.
Press the SET button.
“A” disappears, and “B” is
highlighted in white.
5
6
If you return to the previous menu display
by pressing the B button after setting only
point A
The point A set is cancelled. The points A and B
previously set are retained. If you press the b
button again, you can start setting the point B.
8
Press the SET button at the instant when the picture
comes to the point you want to set as point B.
The point B is set and “B” disappears. The repeat
playback starts between the points A and B set.
Those points A and B are stored until you set new
points A and B or until the disc is unloaded.
Playback starts, and “A” is displayed as a white
letter at the bottom left of the screen.
Note
“A” is highlighted in white.
Stopping repeat playback between points
A and B
The following two methods are available to stop repeat
playback between two points.
• Using the B, b, .PREV/UP, or >NEXT/
DOWN button
• Using a menu operation
To stop repeat playback using the B, b,
.PREV/UP, or >NEXT/DOWN button
Jump to a title or a chapter located outside of the section
specified by the A and B points using the B, b,
.PREV/UP, or >NEXT/DOWN button.
7
Press the SET button at the instant when the picture
comes to the point you want to set that as point A.
To stop repeat playback by menu operations
1
Follow the procedure in steps 1 to 2 described in
FUNCTION item.
37
Repeat Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
2
With “CLEAR REPEAT” highlighted, press the
SET button.
The TOP menu appears.
2
Select “REPEAT FUNCTION” by pressing the V
or v button, and press the b button with “REPEAT
FUNCTION” highlighted.
The unit exits the A-B repeat mode and stops
playback
Conducting repeat playback of the
existing points A and B
The REPEAT FUNCTION display appears.
1
Follow the procedure in steps 2 to 3 described in
item.
2
With “REPEAT” highlighted, press the SET button.
3
4
Select “REPEAT CHAPTER”, by pressing the V or
v button.
Repeat playback between points A and B starts.
When either point A or B has not yet been
set
The error message “NO AB POINT!” appears on
the front panel display and “NO A.B POINT. SET
THE A & B POINT” appears on the monitor
display..
Press the SET button at the instant when the chapter
that you want to repeat comes up.
Repeat Playback of a Chapter
Repeat playback of the current chapter starts.
You can conduct repeat playback of a desired chapter.
Proceed as follows to specify a chapter and conduct
repeat playback.
To stop repeat playback of the chapter
Perform the operation descried in “Stopping repeat
playback between points A and B” on page 37.
1
Press the MENU button.
Repeat Playback of a Title
You can conduct repeat playback of a desired title.
38
Repeat Playback
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to specify a title and conduct repeat
playback.
Playing From the TITLE
LIST Display
You can select the desired chapter and play it back using
the title list.
1
Press the MENU button.
The TOP menu appears.
1
2
Load the disc to be played.
Press the LIST button.
The TITLE LIST display appears.
2
Select “REPEAT FUNCTION” by pressing the V
or v button, and press the b button with “REPEAT
FUNCTION” highlighted.
The REPEAT FUNCTION display appears.
3
Select the title which has the chapter that you want
to display, by pressing the V or v button.
The following display of the selected title appears.
3
4
Select “REPEAT TITLE” by pressing the V or v
button.
When there are plural pages
There are two methods how to move to another
page.
40.
4
Select “PLAY” by pressing the V or v button, and
then press the b button.
Press the SET button at the instant when the title
that you want to repeat comes up.
Repeat playback of the current title starts.
To stop repeat playback of the title
Perform the operation descried in “Stopping repeat
playback between points A and B” on page 37.
39
Playing From the TITLE LIST Display
Download from Www.Somanuals.com. All Manuals Search And Download.
The following display appears.
Verifying Information on
a Disc
You can verify information on a disc.
Proceed as follows to display the DISC
INFORMATION display.
1
Load a disc and press the MENU button.
The TOP menu appears.
5
Select the chapter that you want to play, by pressing
the V or v button, and then press the SET button.
Playback of the selected chapter starts.
Displaying the next page
When there are plural pages of title list displayed in step
3 and chapter list displayed in step 4, the following two
methods are available to display another pages.
2
Press the V or v button to select “DISC INFO” and
press the b button with “DISC INFO” highlighted.
Using the V or v button
1
Highlight the last title or chapter on the current
page to go to the next page by pressing v button.
The DISC INFORMATION display appears.
Each time you press the V or v button, the display
scrolls up or down by one line at a time.
2
Press the v button.
The new page appears.
Using the .PREV/UP or >NEXT/DOWN
button
To go back to the previous page: Press the .PREV/
UP button.
To move to the next page: Press the >NEXT/
DOWN button.
You can very the following information on a disc.
40
Verifying Information on a Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Function
Viewing Frozen Pictures
DISC NAME
MEDIA
To display the disc name.
To display the media type (display
only).
Viewing frozen pictures using buttons on
the unit
The following two methods are available to view a
frozen picture during playback.
TITLE COUNT
REC DATE
To display the number of titles
recorded on a disc (display only).
FIRST: Oldest recording date
among titles recorded in one disc.
LATEST: Latest recording date
among titles recorded in one disc.
(Both are only displayed)
• Pressing the XPAUSE button during playback
Playback stops and the picture at that point is frozen.
In this case, the frozen picture is a field picture.
To cancel to freeze picture and to play again:
Press the XPAUSE button again, or press the BPLAY
button.
DISC REMAIN
To display the remaining recording
capacity in units of time for each
recording mode (display only).
FINALIZE
FORMAT
To finalize a disc.
To format a disc.
• Pressing the v (FREEZE) button during
playback
You can view frame frozen pictures and frozen field
pictures in sequence. When you press the v button the
first time, the picture becomes a frame frozen picture.
When you press the v button the second time, the
frame frozen picture is replaced with the first field
frozen picture. When you press the v button the third
time, the first field frozen picture is replaced with the
second field frozen picture. Whenever you press the v
button, the frozen picture is replaced in this sequence.
SETUP MENU allows you to decide whether the first
frozen picture is a frame frozen or field frozen picture.
To cancel to freeze picture and to play again:
Press the BPLAY button.
To display whole of the disc name
Press the V or v button to select “DISC NAME,”
and press the b button.
Press the b button.
When the unit is controlled using the
SVRM-100A remote control unit
To freeze the playback picture
Press the FREEZE button during playback.
When you press the FREEZE button the first time, the
picture becomes a frame frozen picture.When you press
the FREEZE button the second time, the frame frozen
picture is replaced with the first field frozen
picture.When you press the FREEZE button the third
time, the first field frozen picture is replaced with the
second field frozen picture. Whenever you press the
FREEZE button, the frozen picture is replaced in this
sequence.
You can change the disc name on the above screen.
However, you cannot edit the disc name on this
unit. The RM-P110 (not supplied) is required.
You can edit the disc name using the RM-P110 (not
supplied) connected to the RS-232C connector.
use an RM-P110 (not supplied) as a keyboard for
MENU allows you to decide the first frozen picture to
frame one or field one.
To cancel to freeze picture and to play again
Press the BPLAY button.
For detailed information on the remote control unit, see
To return to the previous DISC INFORMATION
display
Press the MENU button.
41
Viewing Frozen Pictures
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Select the title with information you want to verify
by pressing the V or v button, and press the b
button.
Editing
The following display appears.
Editing Titles
The TITLE LIST menu allows you to carry out the
following editing tasks on titles.
• Verifying information about titles and editing
titles
You can verify information about titles and edit titles
as required.
• Protecting a title
You can protect titles from accidental erasure or
editing.
• Erasing a title
You can erase unnecessary titles.
When there are plural pages in the title list
The following two methods are available to move to
another pages.
• Using the V or v button
Each time you press the V or v button, the display
scrolls up or down by one line at a time.
Highlight the last title on the current page by
pressing v button. When the last title is
highlighted, press the v button.
Verifying/EditingInformationAbout
the Title
The TITLE LIST menu allows you to verify information
about the desired title. Also, you can edit the name and
title information on the TITLE NAME and TITLE INFO
displays.
The new page appears.
• Using the .PREV/UP or >NEXT/
DOWN button
To go back to the previous page: Press the
.PREV/UP button.
To move to the next page: Press the >NEXT/
DOWN button.
Note
4
Select “TITLE NAME” to verify or edit the title
name, or select “TITLE INFO” to view or edit the
title information by pressing the V or v button.
To edit information about titles, the RM-P110 remote
control unit (not supplied) is required.
1
2
Load the disc to be edited.
Press the LIST button.
To verify or edit the title name
The TITLE LIST display appears.
The list of titles is displayed.
42
Editing Titles
Download from Www.Somanuals.com. All Manuals Search And Download.
To verify or edit the title information
When you finish editing:
Press the SET button on the unit after carrying out
editing task using the RM-P110.
The message “SAVING...” appears on the front
panel display while the title name or title
information is being saved. On the monitor display,
“THIS TITLE IS CHANGING INFORMATION.
PLEASE WAIT” appears while the tile name or
title information is being saved.
To verify information from another title
Press the LIST button. The screen returns to the one
in step 3.
Then, push the B button so that the screen returns to
the one in step 2.
5
Press the b button.
The name or information of the title selected in step
3 is displayed.
Finally, repeat steps 2 and 3 to verify information
from another title.
When “TITLE NAME” is selected:
Title name currently displayed
Protecting a Title
The TITLE LIST display allows you to protect titles
from accidental erasure or to prohibit indexes from
being added to or erased from titles.
Proceed as follows.
1
2
Load the disc on which titles that you want to
protect are recorded.
Press the LIST button.
Title name automatically recorded on the disc
TITLE LIST display appears.
The list of titles is displayed.
When “TITLE INFO” is selected:
Title name
3
Select the title that you want to protect from the list
by pressing the V or v button. Then, press the b
button.
Title information
To edit the title name and information
You cannot edit titles and information on this unit.
To edit them, connect the RM-P110 remote control
unit (not supplied) to the unit.
For detailed information on how to use the RM-
43
Editing Titles
Download from Www.Somanuals.com. All Manuals Search And Download.
The following display appears.
Setting
ON
Content
The title is protected.
OFF
The title is not protected. (factory
setting)
7
Press the SET button.
Erasing a Title
Proceed as follows.
When there are plural pages in the title list
The following two methods are available to move to
another page.
• Using the V or v button
• Using the .PREV/UP button or the
>NEXT/DOWN button
1
2
Load the disc on which titles that you want to erase
are recorded.
Press the LIST button.
The TITLE LIST display appears.
The list of titles is displayed.
4
Select “PROTECT” by pressing the V or v button.
The current status
3
Select the title that you want to erase from the title
list by pressing the V or v button, and press the b
button.
5
6
Press the b button.
The following display appears.
The setting display appears.
Select the desired setting pressing the V or v
button.
The name of the selected title
When there are plural pages in the title list
The following two methods are available to move to
another page.
• Using the V or v button
• Using the .PREV/UP button or the
>NEXT/DOWN button
44
Editing Titles
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Select “ERASE” by pressing the V or v button.
erase title 30 which is the last title currently recorded,
the remaining titles are title 1 to title 29. When you
record a title the next time, the new title number will be
30.
If you erase titles other than the last one, the capacity of
the disc does not change. However, the title numbers are
renumbered using the numbers of the titles which were
erase.
Press the b button.
The following display appears.
6
Select “EXEC” by pressing the V or v button.
7
8
Press the SET button.
The message “READY?” appears.
Press the SET button.
The message “ERASING THIS TITLE. PLEASE
WAIT” appears highlighted, and the unit starts
erasing the title selected.
Note
The unit can record up to 49 titles on one disc.
When the last title is erased, the capacity of the disc is
increased by the size of that title. When you erase a title,
adjustment is made to the title numbers based on where
the erased title was in the list of titles. For example, you
45
Editing Titles
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT FUNCTION menu
This menu allows you to repeat playback between two
points (A-B repeat), playback of the chapter and the
title.
Menu
Menu Configuration and
the Menu List
The unit has two kinds of menus: one is the menu
displayed by pressing the MENU button, and the other
is the title list menu displayed by pressing the LIST
button.
This section describes the configuration and the list of
the menu displayed by pressing the MENU button.
on the title list menu, see “Playing From the TITLE LIST
Item
Function
REPEAT A-B
To play a segment specified by two points
(point A and point B) repeatedly
REPEAT
CHAPTER
To play the chapter currently being
played repeatedly
About the front panel display during menu
operation
This manual uses the monitor display for explaining the
menu operation. The items currently highlighted on the
monitor display are displayed on the main display
section of the front panel display.
REPEAT TITLE
To play the title currently being played
repeatedly
CLEAR REPEAT To stop the current repeat playback
DISC INFORMATION menu
The menu allows you to verify details of the disc,
finalize and format the disc.
Whenever you push the B, b, V or v button, the display
changes.
Menu Configuration
Press the MENU button. The TOP menu appears.
Item
Function
DISC NAME
MEDIA
To display the disc name
To display the media type (display only)
The TOP menu is configured as follows.
• REPEAT FUNCTION menu
• DISC INFO menu
• SETUP MENU
For detailed information on menus, see the following
TITLE COUNT
To display the number of titles recorded
on a disc (display only)
REC DATE
FIRST: Oldest recording date among
titles recorded in one disc.
LATEST: Latest recording date among
titles recorded in one disc.
(Both are only displayed)
Menu List
This section describes menus displayed by pressing the
MENU button, using lists.
The setting surrounded with
setting.
DISC REMAIN
To display the remaining recording
capacity in units of time for each
recording mode (display only)
FINALIZE
FORMAT
To finalize a disc
To format a disc
indicates the factory
46
Menu Configuration and the Menu List
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Item
Function
Setting
This menu allows you to perform various settings
depending on your circumstances to use the unit.
BAUDRATE To select a
9600 /[19200]/38400/57600/
communication 115200
speed (baud
rate) when
controlling the
unit by
equipment
connected to
the RS-232C
connector
FOOT SW
To select the
operation to be recording, or pauses
[LOW EDGE]: Starts
carried out
recording during recording,
when you press when you press the foot
or release the
switch. Even if you release
foot switch (not the foot switch, the recording
supplied)
or pause recording status
remains in effective.
Item
Function
Setting
REC MODE To select a
HQ: Records a high-quality
HIGH EDGE: Starts
recording mode picture.
recording or pausing during
recording when you press and
release the foot switch. The
unit does not change from
one operation to another
when you press the foot
switch.
[SP]: Records in standard
mode.
LP: Records for a longer
time.
AUDIO
MON CH
To select a
LCH: Outputs the audio
signal of audio channel 1.
signal to be
output from the
MONITOR
AUDIO
connector on
the rear panel
LOW ACTIVE: While you
hold the foot switch down,
the unit records. When you
release the foot switch, the
unit pauses.
RCH: Outputs the audio
signal of audio channel 2.
[MIX]: Outputs a mixed audio
signal from both channel 1
and channel 2.
a)
AUTO
To select
ON : Marks indexes
INDEX
whether or not automatically every 5
INPUT
SELECT
To select a
[ANALOG]: Inputs the analog
indexes are
automatically
marked during
recording
minutes.
video and audio signal to the VIDEO IN or S-
input signals
VIDEO IN connector.
[OFF]: Does not mark indexes
automatically.
iLINK: Inputs the digital
signal to the DV IN (i.LINK)
connector.
AUTO
TITLE
To select
[ON]: Creates a next title
whether or not a automatically. It is
REMOTE I/F To select an
[RS232C]: Controls the unit
new title is
recommended to select this
setting when connecting VHS
equipment.
interface to use with equipment connected to
to control the
unit
automatically
created when
the number of
indexes in one
title exceeds 99.
the RS-232C connector (a
protocol which is compatible
with the SVO-9500MD Sony
video cassette recorder
protocol).
OFF: Does not create a next
title automatically.
KEY
INHIBIT
To deactivate
buttons to
ON: Activates the key lock
function.
i.LINK: Controls the unit
with equipment connected to
the DV IN (i.LINK)
connector.
protect them
from accidental
operation
[OFF]: Deactivates the key
lock function. All of the
buttons are effective.
except the
USB: Controls the unit with
equipment connected to the
USB connector (a protocol
which is compatible with the
RS-232C protocol).
MENU, LIST,
1 (power), and
OPEN/CLOSE
buttons
KEYBOARD To select
ON: Uses the keyboard.
whether or not
the keyboard of
the RM-P110
remote control
unit (not
[OFF]: Does not use the
keyboard.
supplied) is to
be activated
47
Menu Configuration and the Menu List
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Function
Setting
Item
Function
Setting
FREEZE
MODE
To select the
[FRAME]: Displays a frame
B/W MODE To forcibly
switch the
[OFF]: Processes the signal
from the VIDEO IN, VIDEO
type of frozen frozen picture when you push
picture the button, then the first field
displayed when is frozen when you push the
playback is button next, and then the
paused. (This is second field is frozen when
effective only
when the v
button on the
front panel or
the FREEZE
button on the
SVRM-100A
remote control
unit (not
signal process OUT and S-VIDEO OUT
mode of the
VIDEO IN,
VIDEO OUT
and S-VIDEO
OUT
connectors to
the black and
white signal
connectors as normal color
signals.
ON: Records the signal input
to the VIDEO IN connector
as a black and white signal
with a wide range, and
forcibly cuts the output burst
signal from the VIDEO OUT
and S-VIDEO connectors.
Select this setting when black
and white signals are input to
the VIDEO IN connector and
output from the VIDEO OUT
connector.
you push the button a third
time.
1ST FIELD: Whenever you
push the button, the frozen
picture displayed changes in
the sequence of the first field,
then the 2nd field, and then
the frame.
supplied) is
used)
2ND FIELD: Whenever you
push the button, the frozen
picture displayed changes in
the sequence of the 2nd field,
then the frame, and then the
first field.
DATE/TIME To set the date and time of the unit.
PRESET
MENU
To display the [BASIC]: Displays only the
DISC END
To select the
GOTO TOP: Returns to the
GRADE
enhanced menu basic menu.
operation when beginning of the disc.
ENHANCED: Displays the
enhanced menu under the
basic menu.
the disc
END STOP: Returns to the
becomes full
d)
beginning of the last tile, and
during
end recording automatically.
recording
However, the disc is not
ejected and remains in the
tray.
a) Indexes recorded automatically cannot be erased.
b) If the video signal system does not match the one used in your area, the
disc cannot be played back even if the correct region code is selected.
Set the video signal system to either NTSC or PAL on the TV SYSTEM
sub menu of the ENHANCED MENU.
[EJECT]: Stops recording and
the disc is automatically
ejected.
REGION
CODE
To select the
[1]: Plays a disc recorded in
region code for North America. (This region
c) In Southeast Asia area, the PAL TV system and the NTSC TV system
are mixed. Check whether your TV system is NTSC or PAL before
using this unit.
b)
playback
code is not available for the
PAL video signal system.)
2: Plays a disc recorded in
Western Europe (PAL), the
Middle East (PAL), South
Africa (PAL) and Japan
(NTSC)
d) For detailed information on the enhanced menu, see the
ENHANCED MENU - Enhanced Sub Menu
3: Southeast Asia including
Hong Kong
Proceed as follows to open the enhanced menu.
c)
1
Select “MENU GRADE” on the SETUP MENU by
pressing the V or v button.
4: Central and South
America, and Australia (PAL)
5: Africa (NTSC), Eastern
Europe, Russia, Central Asia,
including India (PAL)
6: China (PAL)
PRE REC
To select
ON Starts recording using the
whether or not last five seconds of video data
the unit starts
recording with
data pre-stored
for five seconds
saved previously.
[OFF]: Starts recording
promptly after you start.
2
Press the b button.
48
Menu Configuration and the Menu List
Download from Www.Somanuals.com. All Manuals Search And Download.
The following display appears.
Item
Function
Setting
REC
To select the REMAIN: Displays the
COUNTER
content of the remaining capacity of the disc.
time display
[COUNTER]: Displays the
on the front
elapsed time of recording.
panel display
during
recording
DEVICE
TYPE
To select the [DVO]: Select this when the unit
device which is connected to video
a)
sends back
equipment such as external
the response equipment.
when a device
SVO9500: Select this when the
type INQ
command of
RS-232C
protocol is
received
unit is used to replace an
existing Sony SVO-9500MD
video cassette recorder.
3
Select “ENHANCED” by pressing the v button,
and press the B button.
The enhanced sub menu items appear under the last
item of the basic menu.
b)
HOUR
METER
To display the Display only
total time of
the use of
hard disc
drive and
DVD drive,
and the
number of
times the tray
is opened and
closed
a) This item is effective when “RS232C” or “USB” is selected for the
“REMOTE I/F” item of the basic menu.
b) The following screen is displayed.
ENHANCED MENU sub menu
Item
Function
Setting
TV SYSTEM To select
either the
[NTSC] /PAL
NTSC or PAL
video signal
system
a)
232C STOP To select the REC PAUSE: Pauses recording.
operation
[REC STOP]: Stops recording.
when a STOP
command is
received from
the RS-232C
interface
during
recording
232C FF/
REW
To select the NEXT/PREV: Performs the
a)
search
same operation of the
operation
when a FF/
REW
>NEXT/DOWN and
.PREV/UP buttons of the
unit when receiving the FF or
command is PREV command.
received from
[FF/REW]: Jumps to the top of
the disc when receiving the FF
command or REW command.
the RS-232C
interface
49
Menu Configuration and the Menu List
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Select the desired basic menu by pressing the V or
v button.
Basic Menu Operations
This section describes the basic menu operations which
are common to each display.
The selected sub menu is highlighted.
This manual describes some menu operations
elsewhere. Read those sections too.
6
1
3
Press the b button.
The next lower sub menu display appears.
3,5
2,4
1
Press the MENU button.
The TOP menu appears.
The item selected is highlighted.
When there are more sub menus under the
currently displayed menu
Access the desired menu display by repeating steps
2 and 3.
The item selected during the last menu operation
using that screen is highlighted.
50
Basic Menu Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Example
6
Press the SET button.
The following screen appears, and the unit starts
saving the settings made.
v
When saving is completed, the message disappears,
and the unit returns to the normal display.
When the following screen appears during a
menu operation
To return to a higher level
Press the B button. Whenever you press the B
button, the screen returns to the menu one level up.
4
When the screen with an item you want to set or
change is displayed, select the desired setting by
pressing the V or v button.
When you highlight “ESC” and press the SET
button:
The unit returns to the menu display one level higher
than the current one without executing the setting.
When you move the cursor to the setting, the setting
is highlighted and selected.
Example: “ANALOG” is selected as the
input signal on the following screen.
When you highlight “EXEC” and press the SET
button:
The confirmation message “READY?” appears.
Press the SET button again.
The message related to the current operation appears,
and the unit completes that operation. When saving is
completed, the message disappears, and the unit returns
to the normal display.
To cancel the menu operation
Push the MENU button in any menu layer before
pushing the SET button.
The message “ABORT!” appears, and all of the changed
settings are cancelled.
The unit returns to the normal screen.
To continue the settings, go to step 5.
To end the menu operation, go to step 6.
5
Access the desired sub menu by pressing the B, b,
V or v buttons, and repeat step 4.
When you have completed all of settings using the
menu, go to step 6.
51
Basic Menu Operations
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous
Messages
The following two types of messages are displayed on
the monitor screen and front panel display.
• Error messages
• Alarm messages
Error Messages
This unit is provided with a self-diagnostic function that
detects internal abnormalities. When it detects an
abnormality, it indicates an error code on the monitor
screen and on the main display section of the front panel
display.
When the error code is displayed, contact your nearest
Sony service facilities.
Monitor screen
Main display section of the front panel display
Error indication
Error code
Error message
Error code
Alarm Messages
When operating the unit, the unit may sometimes output
alarm messages such as the one shown below to the
monitor screen and the front panel display.
Take the remedies according to the message.
Monitor screen
Main display section of the front panel display
ALARM indication
Contents of the alarm
Remedies
52
Messages
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Cause and remedies
Monitor screen
Front panel display
LOW BATTERY.
PLEASE CONTACT SERVICE.
LOW BATTERY!
The unit has detected that the battery is low when the
power was turned on. It is required to replace the battery
with new one.
tPush any button to make the alarm message
disappears. Contact your nearest Sony dealer to
replace the battery with a new one.
MOISTURE HAS BEEN DETECTED.
KEEP THE POWER ON AND WAIT
UNTIL THIS INDICATION GOES OFF.
HUMID!
Condensation may form inside the unit.
tKeep the power on, wait until the alarm message
disappears, and then load the disc.
DISC FULL.
CANNOT ADD NEW TITLES.
DISC FULL!
You loaded a disc which is almost full. This message is
displayed for about five seconds, and then the display
returns to normal.
DISC FULL.
USE ANOTHER DISC.
You tried to record on a disc which was full. This
message is displayed for about five seconds, and then the
display returns to normal.
t Replace the disc with one which has sufficient
capacity for recording.
TITLE FULL.
CANNOT ADD NEW TITLES.
Title FULL!
You loaded a disc on which 49 titles were recorded. This
message is displayed for about five seconds, and then the
display returns to normal.
TITLE FULL.
USE ANOTHER DISC.
You tried to record in on a disc where 49 titles were
already recorded. This message is displayed for about
five seconds, and then the display returns to normal.
disc with one which has sufficient capacity for
recording.
INDEX FULL.
CANNOT ADD NEW TITLES.
Index FULL!
You loaded a disc on which 254 indexes were already
recorded. This message is displayed for about five
seconds, and then the display returns to normal.
INDEX FULL.
CANNOT ADD NEW INDEXES.
You tried to mark an index on a disc where 254 indexes
were already marked, during playback. This message is
displayed for about five seconds, and then the display
returns to normal.
the disc with one which has sufficient capacity for
recording.
INDEX FULL.
USE ANOTHER DISC.
254 indexes have already been recorded. This message is
displayed for about five seconds, and the display returns
to normal.
the disc with one which you can record.
99 INDEXES.
CANNOT ADD NEW INDEXES.
99 indexes!
You tried to mark an index in a title on which 99 indexes
were already marked, during playback. This message is
displayed for about five seconds, and then the display
returns to normal.
99 INDEXES.
MAKE A NEW TITLE.
99 indexes have already been recorded in one title. This
message is displayed for about five seconds, and the
display returns to normal.
tCreate a new title.
NO A.B POINT.
SET THE A & B POINT.
NO AB POINT!
Protected!
Points A and/or B are not set.
tSet the points that are not set yet, using the REPEAT
THIS TITLE IS PROTECTED.
You tried to delete a protected title. You cannot delete
protected titles. This message is displayed for about five
seconds, and then the display returns to normal.
53
Messages
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Cause and remedies
Monitor screen
Front panel display
CANNOT RECORD THIS SIGNAL.
Can't REC!
You tried to record prohibited signals. This message is
displayed for about five seconds, and then the display
returns to normal.
tInput compatible signals.
PLAYBACK PROHIBITED BY REGION
CODE.
REGION CODE!
You tried to play a disc with a region code that is different
from that of the unit. The message disappears when the
disc tray is opened.
tSet the region code of the unit to the same as that of
the disc using the REGION CODE sub menu of the
SETUP MENU.
KEY INHIBIT MODE IS SELECTED.
SET KEY INHIBIT MODE TO OFF.
KEY INHIBIT!
ILL. SETUP!
The key lock function is set. This message is displayed
for about five seconds, and then the display returns to
normal.
tRemove the key lock function by setting the KEY
INHIBIT sub menu of the SETUP MENU to OFF.
ABNORMAL SETTINGS
SELECTED IN SETUP MENU.
SET ITEMS IN THE SETUP MENU TO
THE APPROPRIATE VALUES. CONTACT
SERVICE IF THIS ALARM APPEARS
AGAIN AFTER ABOVE PROCEDURE.
The settings made using the SETUP MENU are wrong.
Push any button to make the alarm message disappear,
then perform the following operation.
the settings made are deactivated again or this
message appears again, contact your nearest Sony
dealer.
NO DISC.
INSERT A DISC.
NO DISC!
PAL DISC!
There is no disc loaded.
tLoad a disc.
DISC CANNOT BE PLAYED BACK.
USE DISC WITH NTSC RECORDING.
A disc recorded using the PAL video signal system has
been loaded in the unit with the NTSC video signal
system set as the default.
tLoad a disc recorded using the NTSC video signal
system.
DISC CANNOT BE PLAYED BACK.
USE DISC WITH PAL RECORDING.
NTSC DISC!
A disc recorded using the NTSC video signal system has
been loaded in the unit with the PAL video signal system
set as the default.
tLoad a disc recorded using the PAL video signal
system.
NOT SUPPORTED DISC.
USE DVD+RW DISC.
Not supported!
A disc that cannot be used with the unit has been loaded.
The message disappears when the disc tray is opened.
tUse a DVD+RW disc that can be used with the unit.
LOADING TIME OVER.
DISC ERROR.
LOADING ERROR!
DISC ERROR!
Recovering...
Can't Recover!
Finalizing...
The unit cannot recognize the disc.
tCheck the disc or replace the disc with another one.
The unit failed in accessing the disc.
tCheck the disc or replace the disc with another one.
RECOVERING THE DISC.
PLEASE WAIT.
The disc is being recovered.
tWait until the message disappears.
CANNOT RECOVER.
CHANGE THE DISC.
The unit failed in recovering.
tReplace the disc with another one.
FINALIZING THE DISC.
PLEASE WAIT.
The unit is finalizing the disc.
tWait until the message disappears.
CANNOT FINALIZE THIS DISC.
CHECK THE DISC.
Fin. Failed!
The unit failed in finalizing.
tReplace the disc with another one.
FORMATTING THE DISC.
PLEASE WAIT.
Formatting...
Init. Failed!
The disc is being formatted.
tWait until the message disappears.
CANNOT FORMAT THIS DISC.
The unit failed in formatting.
tReplace the disc with another one.
54
Messages
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause and remedies
Troubleshooting
The sound is not
heard. The sound is
noisy.
•
The connecting cables have been
removed from the input and output
connectors on the rear panel.
The connections of the input and
output connectors are wrong.
The connecting cable is broken.
tCheck the connecting cables used
to connect the unit to other devices.
The unit is in fast forward or fast
reverse playback mode.
If the unit appears to be malfunctioning, please check
the following before contacting your Sony dealer.
•
Symptom
Cause and remedies
Even if you push
the power switch on
the front panel, the
power is not turned
on.
(The standby
indicator is not lit.)
•
The MAIN POWER switch located on
the rear panel is set to the z (off)
position.
tSet the MAIN POWER switch to
The AC power cord is disconnected.
tCheck whether or not the power
cord is disconnected from the AC
outlet, or that it is connected
•
•
•
•
•
The disc is scratched or dirty.
tUse a disc without scratch or clean
The unit does not
The unit may not work correctly due to
The unit cannot
record.
You tried to use a disc that is write-
protected.
tReplace that disc with one on
which data can be recorded.
The remaining capacity of the disc is
insufficient.
work correctly. For the influence of static electricity.
example,
tPush the 1 (power) switch on the
front panel to turn the power off, and
then set the MAIN POWER switch on
the rear panel to the z (off) position
(see page 15). Next, disconnect the
AC power cord. After a while, re-
connect the AC power cord and turn
the power on again.
The buttons do not
work. The unit
cannot record or
play back.
•
•
tReplace the disc.
49 titles have been already recorded.
In this case, you cannot record any
more data, even if the disc has
sufficient capacity remaining.
tErase unnecessary titles or replace
The disc tray does After you record or edit data on the disc,
not open even if
you push the
OPEN/CLOSE
button.
it may take several seconds for the disc
tray to open. This is because the unit adds
certain required information to the disc. It
is not a malfunction.
•
A disc that cannot be used with the
unit has been loaded.
The power is turned
on, but, images are
not displayed on the
monitor. Or the
•
The connecting cords have been
removed from the input and output
connectors on the rear panel.
The connections of the input and
output connectors are wrong.
The connecting cable is broken.
tCheck the connecting cables used
to connect the unit to other devices.
A signal which is different from the
one selected using the menu is
currently being input.
tSelect the correct input signal using
the INPUT SELECT sub menu of
The disc is scratched or dirty.
tUse a disc without scratches or a
The unit cannot
play.
•
•
A disc has not yet been loaded.
A disc on which no data has been
recorded has been loaded.
image is distorted.
•
tLoad a recorded disc.
•
•
The disc has been loaded cooked.
•
•
A disc that cannot be used with the
unit has been loaded.
tThe unit cannot play a disc other
than the one recorded with the
DVD+RW format.
A disc with a region code different
from that of the unit has been loaded.
tPlay a disc with a region code that
is the same as that of the unit (see
When the unit plays a disc recorded
using other equipment, a disc that has
not been finalized cannot be played.
•
•
•
The image of the
signal input to the VIDEO connector.
VIDEO IN
connector is not
An S video cable is connected to the S-
tRemove the S video cable from the S-
During playback,
The unit stops playback between titles,
the image is frozen and after about one second, starts
for a moment playback of the next title. This is not s
(about one second) malfunction.
and the audio
displayed even
though the INPUT
SELECT item is set
to “ANALOG” in
the SETUP MENU.
breaks up.
The data on the disc Contact your nearest Sony dealer.
is damaged.
55
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Input/Output Connectors
Specifications
Analog video inputs
VIDEO IN (BNC type × 2, loop-
through with 75 Ω automatic
terminator), Composite, 1.0 Vp-p,
75 Ω, sync negative
General
Recording /playback format
DVD +VR format
Video: MPEG-2 @ML(CBR, VBR)
Audio: Dolby digital 2 CH
Signal format system
S-VIDEO IN (4-pin mini DIN × 2,
loop-through with 75 Ω automatic
terminator)
Y: 1.0 Vp-p
NTSC/PAL (switchable using the
menu)
C: 0.286 Vp-p (NTSC), 0.3 Vp-p
(PAL), color burst, 75 Ω, sync
negative
Power requirements
100 to 240 V AC, 50/60 Hz
0.56 A to 0.28 A
Input current
Analog video outputs
Operating temperature
5°C to 40°C (41°F to 104°F)
Operating humidity
20% to 80% (no condensation allowed)
Storage and transport temperature
–20°C to +60°C (–4°F to 140°F)
Storage and transport humidity
75% or less (no condensation allowed)
VIDEO OUT (BNC type × 1)
Composite, 1.0 Vp-p, 75 Ω, sync
negative
S-VIDEO OUT (4-pin mini DIN × 1)
Y: 1.0 Vp-p
C: 0.286 Vp-p (NTSC), 0.3 Vp-p
(PAL), color burst, 75 Ω, sync
negative
Mass
Dimensions
Approx. 6 kg (13 lb 4 oz)
Approx. 212 × 128.5 × 382 mm (w/h/d)
(8 3/8 × 5 1/8 × 15 1/8 inches)
(including the maximum projecting
parts)
Analog audio inputs
AUDIO IN L/R (Phono jack × 1 for
each channel), 2 Vrms (Full bit),
input impedance 47 kΩ or more,
unbalanced
212 (8 3/8)
Analog audio outputs
AUDIO OUT L/R (Phono jack × 1 for
each channel), 2 Vrms (Full bit),
load impedance 47 kΩ, unbalanced
MONITOR AUDIO (Phono jack × 1) 2
Vrms (Full bit), load impedance
47 kΩ, unbalanced
Digital signal
DV IN (i.LINK)
6-pin, complying with IEEE1394
Control Signals
REMOTE 1
Stereo mini jack, for connection of an
SVRM-100A remote control unit
(not supplied)
REMOTE 2
Mini jack, for connection of a foot
switch (not supplied)
REMOTE IN RS-232C
D-sub 9-pin, asynchronous serial
USB (Universal Serial Bus)
Specification Revision 2.0 (up to Full
Speed)
Unit: mm (inch)
56
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Supplied accessories
Using an SVRM-100A
Remote Control Unit
(Not Supplied)
An SVRM-100A connected to the REMOTE 1
connector on the front panel allows you to control the
unit remotely. You can mark indexes and search for the
desired indexes using the jog/shuttle dial.
DPW120MD DVD+RW Disc (1)
DVD InfoEditor Editing Software (1)
Before Using This Unit (1)
CD-ROM (1)
Warranty booklet (1)
Accessories not supplied
SVRM-100A Remote Control Unit
Medical Specifications
This section describes the location and function of parts
and search operations that you can carry out using the
SVRM-100A.
Protection against electric shock:
Class I
Protection against harmful ingress of
water:
Ordinary
Location and Function of Parts
This section describes the functions used for operating
the unit. The buttons on the SVRM-100A corresponding
to ones on the unit have the same function.
Degree of safety in the presence of a
flammable anesthetic mixture with
air or with oxygen or nitrous oxide:
Not suitable for use in the presence
of a flammable anesthetic mixture
with air or with oxygen or nitrous
oxide
1 FREEZE button
2 INDEX button
3 MARK button
4 ERASE button
Mode of operation:
Continuous
Design and specifications are subject to change without
notice.
5 STOP button
6 REC button
7 PAUSE button
8 F FWD button
9 PLAY button
0 REW button
qaJOG/SHUTTLE button
qsJOG/SHUTTLE dial
1 FREEZE button
Outputs the FREEZE command.
2 INDEX button
Outputs the INDEX command.
When you press this button once, the unit enters in
the index scan mode. When you press this button
twice, the unit enters in the index search mode.
3 MARK button
Outputs the MARK command.
4 ERASE button
Outputs the ERASE command.
5 STOP button
Outputs the STOP command.
57
Using an SVRM-100A Remote Control Unit (Not Supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
6 REC button
Outputs the REC command.
3
4
Press the INDEX button on the remote control unit
one time.
7 PAUSE button
The INDEX command is sent and the unit is put in
the index scan mode.
Outputs the PAUSE command.
When the unit receives this command during
playback, it pauses playback.
When the unit receives this command during
recording, it pauses recording.
To search for an image located before the current
position, press the REW button.
To search for an image located after the current
position, press the F FWD button.
8 F FWD button
Has the same function as the >NEXT/DOWN
button of the unit.
When the unit detects an index signal, the unit plays
back the image recorded at that point for about 10
seconds, and then searches for the next index
signal.
9 PLAY button
Outputs the PLAY command.
The unit searches for the index signals repeatedly
up to the beginning or end of the disc.
0 REW button
To cancel the index scan mode
Has the same function as the .PREV/UP button
The index scan mode is automatically cancelled when
the unit searches as far as the beginning or end of the
disc. To cancel the index scan mode before reaching the
beginning or end of the disc, press any one among STOP
button, PLAY button,B and b buttons of the unit and the
SVRM-100.
of the unit.
qa JOG/SHUTTLE button
To play back in jog/shuttle mode using the jog/
shuttle dial, press this button. The indicator lights
up.
qs JOG/SHUTTLE dial
Cuing a Particular Image by
Specifying an Index Number - Index
Search
The playback direction and speed are determined
according to the position of the shuttle dial, and the
search command is output.
The jog dial becomes effective when the shuttle dial
is set to the STILL position.
1
2
3
Load a disc on which indexes are recorded.
Set the unit in stop or playback mode.
The playback speed and direction are determined
according to the direction in which the dial is turned
and the speed, and the search command is output.
Press the INDEX button on the remote control unit
twice.
The unit enters in the index search mode.
Marking Indexes
You can mark indexes at the desired point during
recording and playback.
4
5
Specify the desired index number by pressing the
INDEX button on the control unit the number of
times that corresponds to the number of the desired
index.
1
2
Set the unit in the recording or playback mode.
Press the MARK button at the instant when the
image to which the index is to be put is displayed.
To search for an image located before the current
position, press the REW button.
To search for an image located after the current
position, press the F FWD button.
You can mark up to 99 indexes in one title and up to
254 indexes on one disc.
Searching for a Particular Image -
Index Scanning
Erasing an Index
You can ease indexes marked by pressing the MARK
button of the SVRM-100A remote control unit.
Proceed as follows to erase an index.
1
2
Load a disc on which indexes are recorded.
Set the unit in stop mode or playback mode.
58
Using an SVRM-100A Remote Control Unit (Not Supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
You cannot erase indexes created at the beginning of
recording, ones created by pressing the XPAUSE button
of the unit during recording, or ones marked
automatically by setting the AUTO INDEX sub menu to
1
2
3
Set the unit in the index scan mode.
Search for the index to be erased.
Press the ERASE button.
The index searched in step 2 is erased.
In this case, the segment of that chapter is added to
the previous chapter and they become one chapter.
59
Using an SVRM-100A Remote Control Unit (Not Supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mbps
Mbps is the abbreviation of Mega
bits per second.
Glossary
Bit rate
Mbps is used to indicate the
transmission speed of data. Bit is the
unit used to indicate the size of data
handled in computers. 1Mbps means
that 1,000,000 digital signals can be
handled for one second.
Bit rate is the value indicating
amount of compressed information
recorded on the DVD disc per one
second. The unit is Mbps (Mega bits
per second) for video signals.
1Mbps indicates that the amount of
information per second is 1,000,000
bits. For audio signals, kbps (kilo
bits per second) is used. The larger
this value, the larger the amount of
information involved. However, this
value does not relate to the picture
and sound quality.
Original title
Titles actually recorded on the
DVD+RW (VR mode).
Once they are edited, they cannot be
restored to their original state.
Region code
A code to specify the region where
the disc can be played back. DVD
recorders and DVD players have
their own region codes. A disc can
be played back only when the region
codes of both the player and the
recorder are the same.
Chapter
A segment of an image divided by
two indexes.
Dolby Digital format
Dolby Digital is an audio data
compression technology developed
by Dolby Laboratories. This is
known as “Dolby Surround.” The
output signals are composed of 1
channel of woofer for playback of
the low sound, in addition to right
and left of front, center, and right
and left of rear. This is called 5.1
channel surround. 2-channel
playback is available for the DVO-
1000MD.
Title
The largest unit of images or music
recorded on a DVD. Normally, for
image software, one film is one title,
and for music software, one album
(or a piece of music) is one title.
With the DVO-1000MD, one title is
the image recorded from the start of
recording to the end of recording.
Finalize
To arrange data on a recorded DVD
disc so that it can be played back
with another piece of DVD
equipment.
A DVD+RW disc is finalized when
it is unloaded after being recorded.
However, finalization is required
even when a disc is played back
using equipment compatible with
DVD+RW discs. The disc can be
recorded on again even if it is
finalized.
Index
An index is a mark put at a desired
point during playback or recording.
The DVO-1000MD can place up to
99 indexes for one title and up to 256
indexes on one disc.
60
Glossary
Download from Www.Somanuals.com. All Manuals Search And Download.
verifying/editing title information
Index
P
A
Playback
V
adding indexes during playback
C
Chapter
D
Disc
R
Recording
Repeat playback
F
S
Setup
I
disc end setting when recording
Index
L
Locations and function of parts
SVRM-100A remote control unit (not
supplied)
M
Menu
T
Title
Messages
61
Index
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|