3-204-677-12(1)
Digital
Videocassette
Player
Operating Instructions
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
DSR-1600/1600P
© 2000 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Cuing Up to Any Desired Position Set as Point
Displaying Time Data and Other Text
Displaying Time Data and Operation Mode
Indications ...........................................................31
High-Speed and Low-Speed Search—Quickly
Table of Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Returning Menu Settings to Their Factory Default
Connections for a Digital Non-Linear Editing
Table of Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Chapter
1
Because the recording is digital, multi-generation dubbing
can be performed with virtually no deterioration of quality.
Features
Wide track pitch
1
The DSR-1600/1600P is a / -inch digital video cassette
4
The recording track pitch is 15 µm, fully 50 percent wider
than the 10-µm track pitch of the DV format. Thanks to this
feature, the DVCAM format sufficiently meets the
reliability and precision requirements of professional
editing.
player using the DVCAM digital recording format. It
achieves stable, superb picture quality by digitally
processing video signals separated into color difference
signals and luminance signals (component method).
The unit is equipped with a variety of functions needed for
videocassette players used in professional digital video
editing systems. It supports the ClipLinkTM function
developed by Sony Corporation for highly efficient video
editing. When connected to a Sony EditStationTM, the unit
serves as part of a powerful non-linear editing system*.
The unit is also equipped with a full-fledged analog
interface to support hybrid systems that combine
High-quality PCM digital audio
PCM recording makes for a wide dynamic range and a
high signal-to-noise ratio, thereby enhancing sound
quality.
There are two recording modes: 2-channel mode (48-kHz
sampling and 16-bit quantization), which offers sound
quality equivalent to the DAT (Digital Audio Tape)
format, or 4-channel mode (32-kHz sampling and 12-bit
quantization). Cassettes recorded in either mode can be
played back on this unit.
conventional analog equipment with digital equipment.
* Non-linear editing: This is an editing method that uses video and audio
signals digitally encoded and recorded on a hard disk as digital data. When
compared with conventional (linear) editing methods, non-linear editing
offers vastly improved efficiency in editing operations, for example, by
eliminating tape transport time.
Playback compatibility with DV and
DVCPRO formats
A DV cassette recorded on a DV format VCR as well as a
DVCPRO (25M) format recorded cassette can be played
back on this unit.
The main features of the unit are described in the
following.
DVCAM Format
Note
DVCAM is based on the consumer DV format, which uses
When playing back a tape recorded in DVCPRO (25M)
interfaces” on page 6) of this unit are muted. Furthermore,
it is not possible to playback the cue-audio track of the
tape.
1
the 4:1:1 component digital format, and provides a / -inch
4
digital recording format for professional use.
High picture quality, high stability
Video signals are separated into color difference signals
and luminance signals, which are encoded and compressed
to one-fifth size before being recorded to ensure stable and
superb picture quality.
Features
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Support for three cassette sizes
Facilities for High-Efficiency Editing
There are two sizes of DVCAM cassette: standard and
mini. You can use either size with this unit.
The unit also accepts L and M sizes of DVCPRO cassette.
• When a cassette is inserted, the reel mechanism of the
unit automatically adjusts to the size of the inserted
cassette.
The unit provides an abundance of functions that enhance
editing efficiency and precision.
Support for ClipLink function
In response to commands sent from the EditStation, index
pictures recorded on tape or ClipLink log data recorded in
the cassette memory can be transferred to the EditStation.
The EditStation operator can then efficiently use these
pictures and data in a preliminary editing session.
• The capacity of a standard cassette is 184 minutes of
playback, and that of a mini cassette is 40 minutes.
A Wealth of Interfaces
For an overview of the ClipLink function, see the appendix
Digital interfaces
The following optional digital interfaces are available for
use with the unit.
Internal time code reader
SDTI (QSDI)* (optional DSBK-1602 SDTI (QSDI)
Output Board): When the unit is fitted with the
optional DSBK-1602 board, it can transfer
compressed SDTI (QSDI)-format video, audio and
time code signals to the Sony EditStation at normal
speed.
SDI (serial digital interface)/AES/EBU (optional
DSBK-1601 SDI/AES/EBU Output Board): When
the unit is fitted with the optional DSBK-1601 board,
it can output D1 (component)-format digital video and
audio signals and also AES/EBU-format digital audio
signals.
i.LINK (DV)** (optional DSBK-1803 i.LINK/DV
Input/Output Board): The optional DSBK-1803
board (i.LINK compatible) enables input/output of
digital video and audio signals in DV format (output
only when installed in the DSR-1600/1600P).
An internal time code reader enables time code compliant
with SMPTE (for DSR-1600)/EBU (DSR-1600P) format
to be played back. This allows editing to single frame
precision.
Outputting time code (LTC) to an external device is also
possible using the TIME CODE OUT connector.
The unit is also compatible with VITC.
Remote control
The unit can be operated by remote control from an editing
control unit that supports the RS-422A interface or from an
optional SIRCS*-compatible remote control unit such as
the DSRM-10.
* SIRCS (Sony Integrated Remote Control System): A command protocol
to remote control Sony professional videocassette recorders/players.
* SDTI is the name of a standard interface established as SMPTE 305M.
QSDI is a type of SDTI. This unit uses SDTI to transmit DV data, and the
input/output connectors are labeled “SDTI (QSDI).”
** i.LINK and are trademarks and indicate that this product is in agreement
with IEEE1394-1995 specifications and their revisions.
Playback control using search dial
The search dial on the front panel of the unit allows you to
carry out playback operation in jog or shuttle mode
without requiring an external editing control unit or remote
control unit to be connected to the unit.
Analog interfaces
The unit also comes with analog interfaces enabling it to be
connected to analog video and audio equipment.
Analog video: Output connectors for component,
composite, and S-video signals are provided.
High-speed search function
The unit has a picture search function that allows you to
view color picture at playback speeds up to 85 times
normal speed in forward and reverse directions.
When remote-controlling this unit in shuttle mode from an
editing control unit or a remote control unit, you can search
at any speed in the range 0 (still) to 60 times normal speed
in both directions. You can also search frame-by-frame in
jog mode.
Analog audio: Four output channels are provided.
At search speeds up to 10 times normal speed in both
directions, you can also hear playback audio.
Features
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital hours meter: The digital hours meter functions
include four kinds of tally operations for operating
hours, head drum usage hours, tape transport hours,
and tape threading/unthreading times. The tally results
can be viewed on the video monitor or the time counter
display.
Digital slow-motion playback
Using the frame memory function, the unit can show
noise-free slow-motion playback at speeds ranging from 0
1
to / times normal speed in both directions.
2
Digital jog sound function
1
When searching at speeds in the range +1 to + / * or
30
Compatible with wide-screen aspect ratio
(16:9)
The unit can play back aspect ratio information. When
video accompanied by wide-screen aspect ratio
information is played back, the unit can output the video
signal also containing the aspect ratio information.
1
− / to −1 times normal speed, the digital jog sound
30
function is enabled. The audio signal is saved in temporary
memory, and replayed according to the search speed. This
allows searching on the sound track.
* The positive direction refers to forward movement of the tape, and the
negative direction to reverse movement.
Rack mountable
When you use the optional RMM-130 Rack Mount Kit,
you can mount this unit onto an EIA-standard 19-inch rack
(height = 4 units).
Video process control
For analog video output and SDI-format video output, you
can adjust the video output level, chroma signal output
level, setup level (for DSR-1600), black level (for DSR-
1600P), and chroma phase.
Optional Accessories
Other Features
DSBK-1601 SDI/AES/EBU Output Board
When installed in the unit, this optional board enables
digital video and audio signals in the D1 format and also
AES/EBU-format digital audio signals to be output from
the unit to digital Betacam VCRs or other equipment.
Function to make a convenient
presentation tool of this unit
“Repeat playback” function
The unit can perform automatic cyclical playback between
two selected points on the tape.
DSBK-1602 SDTI (QSDI) Output Board
This interface allows the unit to transfer video, audio and
time code signals in SDTI (QSDI) format to the Sony
EditStation at normal speed. When this unit is connected to
another DVCAM VCR, it is possible to transfer
“Power-on playback” function (in repeat
playback mode)
You can choose a menu setting so that powering on the
unit makes it immediately start playback.
compressed signals from this unit to the connected VCR.
Menu system for functionality and
operation settings
The unit provides a menu system to make its various
functions easier to use and set up its operation conditions.
DSBK-1803 i.LINK/DV Input/Output Board
This board allows you to connect the unit to other
equipment provided with a Sony DV connector to carry
out editing or dubbing of digital video and audio signals.
Superimposition function
Time code values, operation mode indications, error
messages, and other text data can be superimposed and
output in analog composite video signals.
RMM-130 Rack Mount Kit
This kit can be used to mount the unit onto an EIA-
standard 19-inch rack.
Easy maintenance functions
Self-diagnostic/alarm function: This function
automatically detects setup and connection errors,
operation faults, and other problems. It also displays a
description of the problem, its cause, and the
recommended response on the video monitor screen or
time counter display.
Features
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
Front Panel
a POWER switch
b Audio level meters
ꢀꢀꢀꢀꢀ
c PB FS display
d Cassette compartment
POWER
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
PB FS
48k44.1k32k
-60
-60
-60
-60
A
B
MARK
A Menu control panel (inside of
E Remote control
the door) (see page 9)
setting section
D Search control section
g CONTROL S connector
f HEADPHONES connector
e PHONE LEVEL control knob
a POWER switch
d Cassette compartment
Accepts DVCAM, DV and DVCPRO (25M)
videocassettes.
Press the “ ” side to power the unit on. When the unit is
powered on, the display windows in the front panel lights.
To power the unit off, press the “ ” side of the switch.
b Audio level meters
These show the audio levels of channels 1 to 4 during
e PHONE LEVEL control knob
playback.
Controls the volume of the headphones connected to the
HEADPHONES connector.
c PB FS (playback audio sampling frequency)
display
Indicates the sampling frequency (48 kHz, 44.1 kHz or 32
f HEADPHONES connector (stereo phone jack)
Connect stereo headphones for headphone monitoring
during playback.
kHz) at which audio is recorded on tape.
The audio signal you want to monitor can be selected with
the MONITOR SELECT switches on the menu control
panel.
Location and Function of Parts
8
Download from Www.Somanuals.com. All Manuals Search And Download.
g CONTROL S connector (stereo minijack)
Connect a SIRCS-compatible remote control unit such as
the DSRM-10.
A Menu control panel
The menu control panel is located on the inside of the door
at the lower front of the unit. Pull the top of the door to
open it.
a MONITOR SELECT switches
b MENU button
c COUNTER SEL button
d RESET (NO) button
MIX
A
B
e SET (YES) button
MARK
f
buttons
g SC PHASE control
h SYNC PHASE control
a MONITOR SELECT switches
Switch setting
Selected channel and output
format
Use these switches to select the channels for audio output
via the AUDIO MONITOR OUT connector on the rear
panel and the HEADPHONES connector on the front
panel.
Use the left switch to select the basic channel setting, then
use the right switch to select the output format (monaural,
stereo, or mix).
Left
switch
Right
switch
HEADPHONES AUDIO
connector
MONITOROUT
connector
Channel 1 only Channel 1 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channels 1 and Channels 1 and
2 (stereo) 2 (mix)
The following table lists the correspondence of left/right
switch settings and channel/output format selections.
CH-
1/3
CH-
2/4
CH-
1/2
CH-
3/4
MIX
Channel 2 only Channel 2 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channel 3 only Channel 3 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Channels 3 and Channels 3 and
4 (stereo) 4 (mix)
CH-
1/3
CH-
2/4
CH-
1/2
CH-
3/4
MIX
Channel 4 only Channel 4 only
(monaural) (monaural)
CH-
1/3
CH-
2/4
MIX
Location and Function of Parts
9
Download from Www.Somanuals.com. All Manuals Search And Download.
b MENU button
• send a negative response to the prompts issued by the
unit.
Press this button to display the menu on the monitor screen
and the time counter display. Press it again to return from
the menu display to the usual display.
e SET (YES) button
Press this button to:
• save new menu settings to the memory of the unit,
• confirm the start and end point settings for repeat
playback, or
c COUNTER SEL (selection) button
Selects the type of time data to be shown in the time
counter display. Each press of this button cycles through
three indicator display options: COUNTER (CNT: count
value of the time counter), TC (time code), and U-BIT
(user bits).
• send a positive response to the prompts issued by the
unit.
f Arrow (JjK k) buttons
Use these buttons to move around the menu items, and also
to specify and check the repeat playback section.
Note
When the REMOTE button in the remote control setting
section is lit, the COUNTER SEL button does not operate.
In this case, make the time data selection via the remote
equipment that is connected to the REMOTE connector on
the rear panel.
g SC (subcarrier) PHASE control
Turn this control to accurately adjust the subcarrier phase
of the composite video output signal of the unit with
respect to the reference video signal. Use a cross-point
(Phillips) screwdriver to turn it.
d RESET (NO) button
Press this button to:
• reset menu settings,
• reset the time count (COUNTER) shown in the time
counter display to zero, or
h SYNC (synchronization) PHASE control
Turn this control to accurately adjust the synchronization
phase of the output video signal of the unit with respect to
the reference video signal. Use a cross-point (Phillips)
screwdriver to turn it.
B Tape transport control section
a EJECT button
b REW button
e STOP button
d F FWD button
c PLAY button
a EJECT button
When you press this button, it lights and the cassette is
c PLAY button
When you press this button, it lights and playback begins.
automatically ejected after a few seconds.
d F FWD (fast forward) button
b REW (rewind) button
When you press this button, it lights and the tape is fast
forwarded (maximum 85 times normal speed). You can
monitor the playback picture during the fast forward.
When you press this button, it lights and the tape starts
rewinding (maximum 85 times normal speed). You can
monitor the playback picture during the rewind.
Location and Function of Parts
10
Download from Www.Somanuals.com. All Manuals Search And Download.
e STOP button
Note
Press this button to stop the current tape transport
operation.
No tape transport control buttons other than the EJECT
and STOP buttons will work while the REMOTE button in
the remote control setting section is lit. This can be
changed with the LOCAL ENABLE menu item (see page
40).
C Display section
a Playback format indicators
b ClipLink indicator
c VITC indicator
d Time data type indicators
e Time counter display
h CHANNEL CONDITION indicators
g SERVO indicator
f Cassette memory indicator
i REPEAT indicator
j Tape end alarm indicator
k SHUTTLE/JOG indicators
a Playback format indicators
DVCAM: This lights when a tape recorded in DVCAM
format is played back.
When a tape recorded in DVCPRO (25M) format or any
other format than those mentioned above is played back,
none of the above indicators lights.
DV: This lights when a tape recorded in consumer DV
format is played back.
LP: This lights when a tape recorded in LP mode is played
back.
Note
A tape recorded in LP mode cannot be played back
correctly. When a tape recorded in LP mode is played
back, “DV LP” flashes and audio is muted.
Location and Function of Parts
11
Download from Www.Somanuals.com. All Manuals Search And Download.
b ClipLink indicator
Lights when a cassette is loaded on which ClipLink log
data is stored in the cassette memory.
k SHUTTLE/JOG indicators
When searching in shuttle mode using the search dial, the
SHUTTLE indicator lights, and when searching in jog
mode using the search dial, the JOG indicator lights. When
the search dial is turned clockwise causing playback to
take place in the forward direction, the G indicator lights.
When the search dial is turned counterclockwise causing
playback to take place in the reverse direction, the g
indicator lights. When the tape is stopped, the s indicator
lights.
For details of ClipLink log data, see the appendix
c VITC indicator
Lights when VITC is being read regardless of the data
shown in the time counter display.
d Time data type indicators
One of the three indicators (COUNTER, U-BIT, and TC)
lights to indicate the type of time data currently shown in
the time counter display.
COUNTER: Count value of the time counter
U-BIT: User bit data
D Search control section
TC: SMPTE time code (for DSR-1600) or EBU time code
(for DSR-1600P)
e Time counter display
Indicates the count value of the time counter, time code,
VITC, or user bit data depending on the settings of the
COUNTER SEL button on the menu control panel and the
TC SELECT menu item (see page 43).
Also used to display error messages and setup menu data.
f Cassette memory indicator
Lights when a cassette provided with a memory chip
(“cassette memory”) is loaded.
b Search dial
g SERVO indicator
a SEARCH button
This indicator lights when the drum servo and capstan
servo are locked*.
a SEARCH button
* Servo lock: This refers to the synchronization of the phase of the drum
rotation and the reference signal for the tape transport position, so that the
video heads can trace the same pattern on the tape for playback and
recording.
To use the search dial for playback in shuttle or jog mode,
press this button, turning it on. Pressing the dial toggles
between shuttle and jog modes. In shuttle mode, the
SHUTTLE indicator in the display section lights, and in
jog mode, the JOG indicator in the display section lights.
h CHANNEL CONDITION indicators
These three-color indicators show the state of the playback
signal.
Green: The state of the playback signal is good.
Yellow: The playback signal is somewhat deteriorated, but
playback is possible.
Red: The playback signal is deteriorated. When the red
indicator remains on, head cleaning or an internal
inspection is necessary.
b Search dial
Turn this to carry out playback in the modes shown in the
following table. Turning the dial clockwise lights the G
indicator in the display section and plays back in the
forward direction. Turning the dial counterclockwise
lights the g indicator in the display section and plays back
in the reverse direction. When the tape is stopped, the s
indicator in the display section lights.
Pressing this dial toggles playback between shuttle mode
and jog mode. When playing back in shuttle mode, the
SHUTTLE indicator in the display section lights, and
i REPEAT indicator
This indicator lights when the REPEAT MODE menu item
(see page 40) is set to ON.
when playing back in jog mode, the JOG indicator lights.
j Tape end alarm indicator
Starts flashing when the remaining capacity of the tape is
for about 2 minutes.
1
You can carry out noiseless playback in the range of
times normal speed.
/
2
Location and Function of Parts
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback modes using the search dial
Playback mode Operation and functions
this button, turning it on. This requires the optional DSBK-
1803 board to be installed.
Shuttle
Press the SEARCH button or the search
dial so that the SHUTTLE indicator in
the display section lights, then turn the
search dial.
Playback is carried out at a speed
determined by the position of the search
dial. The maximum shuttle mode
playback speed can be changed with the
Jog
Press the SEARCH button or the search
dial so that the JOG indicator in the
display section lights, then turn the
search dial. Playback is carried out at a
speed determined by the speed of
rotation of the search dial. The playback
speed is up to 1 times normal speed by
factory default.
The search dial has no detents.
You can use the SEARCH ENABLE menu item (see page
40) to select either of the following as the operation to be
performed to put the unit into search mode (shuttle or jog).
• Either press the SEARCH button or turn the search dial
(factory default setting).
• Press the SEARCH button.
E Remote control setting section
a REMOTE button
b 9PIN button
c i.LINK button
a REMOTE button
When remote-controlling this unit from the unit connected
to the REMOTE connector or DV IN/OUT connector,
press this button, turning it on.
When reverting to local mode to use the buttons in the tape
transport control section, press this button again, turning it
off.
b 9PIN button
When carrying out remote control between this unit and
the unit connected to the REMOTE connector, press this
button, turning it on.
c i.LINK button
When carrying out remote control between this unit and
the unit connected to the DV IN/OUT connector, press
Location and Function of Parts
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
SDI OUT
AUDIO OUT(AES/EBU)
CH-1/2
CH-3/4
SDTI(QSDI)OUT
DV IN/OUT
1
2
ANALOG VIDEO
REF. VIDEO
TIME
AUDIO OUT
CH-1
MONITOR
OUT
AUDIO
VIDEO S VIDEO
CODE
COMPONENT VIDEO
OUT
IN
OUT
OUT
OUT
OUT
1
2
Y
CH-2
CH-3
CH-4
REMOTE
VIDEO CONTROL
B-Y
R-Y
(SUPER)
~AC IN
AC IN connector
AC IN connector
Use the supplied power cord to connect this to an AC
outlet.
Location and Function of Parts
14
Download from Www.Somanuals.com. All Manuals Search And Download.
A Analog video signal output section
ANALOG VIDEO
REF. VIDEO
TIME
CODE
VIDEO
OUT
S VIDEO COMPONENT VIDEO
OUT
IN
OUT
OUT
OUT
1
2
Y
a REF. VIDEO IN/OUT
B-Y
R-Y
connectors
(SUPER)
e TIME CODE OUT connector
d COMPONENT VIDEO OUT Y/R−Y/B−Y
connectors
c S VIDEO OUT connector
b VIDEO OUT 1 and 2 (SUPER) connectors
a REF. (reference) VIDEO IN/OUT connectors
(BNC type)
set to ON (factory default setting), connector 2 (SUPER)
outputs a signal with superimposed text information.
Input a reference video signal. The IN connector block has
a built-in automatic 75 Ω termination switch. When a
signal is input to the upper REF. VIDEO IN connector
with no bridging (loop-through) connection made, the
connector is terminated with an impedance of 75 Ω
automatically. To connect the reference video signal input
to the upper REF. VIDEO IN connector also to other
equipment, use the lower REF. VIDEO IN connector
c S VIDEO OUT connector (4-pin)
This connector outputs an S-video signal with separated Y
(luminance) and C (chroma: 3.58 MHz for DSR-1600 or
4.43 MHz for DSR-1600P) components.
d COMPONENT VIDEO OUT Y/R−Y/B−Y
connectors (BNC type)
(marked
). When the lower REF. VIDEO IN connector
These connectors output analog component video signals
is used, the built-in 75 Ω termination switch turns off
automatically.
(Y/R−Y/B−Y).
The REF. VIDEO OUT connector outputs a reference
video signal.
e TIME CODE OUT connector (BNC type)
Outputs the playback time code.
b VIDEO OUT 1 and 2 (SUPER) connectors (BNC
type)
These connectors output analog composite video signals.
Location and Function of Parts
15
Download from Www.Somanuals.com. All Manuals Search And Download.
B Digital signal output section (optional DSBK-1601/1602/1803 boards required)
DV IN/OUT
a
DV IN/OUT connector
SDTI(QSDI)OUT
b SDTI (QSDI) OUT connector
SDI OUT
AUDIO OUT(AES/EBU)
CH-3/4
2
CH-1/2
1
d AUDIO OUT (AES/EBU)
connectors
c SDI OUT connectors
a
DV IN/OUT connector (6-pin IEEE-1394)
(optional DSBK-1803 i.LINK/DV Input/Output
Board required)
c SDI (Serial Digital Interface) OUT connectors
(BNC type) (optional DSBK-1601 SDI/AES/EBU
Output Board required)
This i.LINK-compatible connector (subsequently referred
to also as the i.DV IN/OUT connector) outputs digital
video and audio signals in DV format.
Output SDI-format digital video and audio signals. The
same signals are output from both connectors.
d AUDIO OUT (AES/EBU) connectors (BNC type)
(optional DSBK-1601 SDI/AES/EBU Output
Board required)
These connectors output digital audio signals in AES/EBU
format. The left connector (CH-1/2) is for audio channels
1 and 2, and the right connector (CH-3/4) is for audio
channels 3 and 4.
Note
1
1
When searching at speeds in the range + / to + / or
2
30
1
1
− / to − / times normal speed, the audio signal output
2
30
from this connector and monitored on external equipment
may sound differently from the audio signal played back
on this unit.
b SDTI (QSDI) (Serial Data Transport Interface
(QSDI)) OUT connector (BNC type) (optional
DSBK-1602 SDTI (QSDI) Output Board required)
Outputs digital video and audio signals in SDTI (QSDI)
format.
Note
1
1
When searching at speeds in the range + / to + / or
2
30
1
1
− / to − / times normal speed, the audio signal output
2
30
from this connector and monitored on external equipment
may sound differently from the audio signal played back
on this unit.
Location and Function of Parts
16
Download from Www.Somanuals.com. All Manuals Search And Download.
C Analog audio signal output section
MONITOR
OUT
AUDIO OUT
AUDIO
CH-1
CH-2
CH-3
CH-4
b AUDIO MONITOR OUT connector
a AUDIO OUT CH-1 to CH-4 connectors
a AUDIO OUT CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, male)
D External device connectors
These connectors output channel-1 to channel-4 analog
audio signals, respectively.
It is possible to use the AUDIO OUT CH-3 and AUDIO
OUT CH-4 connectors for audio monitor output for
channels 1 and 2, respectively (use the OUTPUT CH3/4
VIDEO CONTROL
REMOTE
b AUDIO MONITOR OUT connector (RCA phono
jack)
This connector outputs audio signals for monitoring. The
audio signals to be output from this connector can be
selected with the MONITOR SELECT switches on the
menu control panel.
b REMOTE connector
a VIDEO CONTROL connector
a VIDEO CONTROL connector (D-sub 15-pin)
For remote control of the internal digital video processor,
connect an optional remote control unit such as the UVR-
60/60P or BVR-50/50P to this connector.
b REMOTE connector (D-sub 9-pin)
When controlling this unit from an editing control unit
such as the ES-3, ES-7, PVE-500, BVE-600/800/910/
2000, or RM-450/450CE, connect the unit to the editing
control unit via this connector using the optional 9-pin
remote control cable.
Location and Function of Parts
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and Function of Parts
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Chapter
2
Playback
This section describes the necessary settings and operations to perform playback
on this unit. The same settings and operations apply whether you are using the
unit as part of an editing system, for dubbing, or as a stand-alone player VCR.
For the necessary connections and settings not covered in this section, see
Usable Cassettes
This unit can use the DVCAM cassettes listed below.
Model name
Size
PDV-64ME/94ME/124ME/184ME
PDVM-12ME/22ME/32ME/40ME
Standard size
Mini size
The numbers in each model name indicate the maximum playback time (in
minutes) for each model. For example, the PDV-184ME has a maximum
playback time of 184 minutes.
Other usable cassettes
All consumer DV cassettes and large- and medium-size DVCPRO (25M)
cassettes can also be played back on this unit.
Notes
• If you insert an incorrect type of cassette, it will be automatically ejected.
• You can also use DV cassettes on the unit. However, it is the best choice to
always use DVCAM cassettes because they are more reliable than DV
cassettes whatever your purpose may be: playback, editing, or long-period
storage of recordings.
Playback
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DVCAM cassettes
The following figure illustrates the DVCAM cassettes.
REC/SAVE switch
Set to SAVE to prohibit recording on the tape.
Mini size
Standard size
Cassette memory
This memory is used to store ClipLink log data.
For details of ClipLink log data, see the appendix
Notes on using cassettes
• Before storing the cassette for a long period of time, rewind the tape to the
beginning and be sure to put the cassette in its storage case, preferably on end
instead of flat on its side.
Storing a cassette in any other condition (not rewound, out of its case, etc.)
may cause the video and audio contents to become damaged over time.
• If the cassette memory connector (contact point) becomes dirty, connection
problems may occur, causing a loss of functions. Remove away any dust or
dirt from this area before using the cassette.
• If the cassette is dropped on the floor or otherwise receives a hard impact, the
tape may become slackened and may not play back correctly.
For information about how to check the tape for slack, see the next section.
Checking the tape for slack
Using a paper clip or a similar object, turn the reel gently in the direction shown
by the arrow. If the reel does not move, there is no slack. Insert the cassette into
the cassette compartment, and after about 10 seconds take it out.
Paper clip, etc.
Reel
Playback
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting and Ejecting Cassettes
Inserting a cassette
This unit accepts three sizes of cassette: L (standard size), M (medium size:
DVCPRO) and S (mini size). When inserting a cassette in the unit, make sure
its tape window faces upward as shown in the following figure.
Outer guides
Mini size (Insert the cassette into the
middle of the cassette compartment.)
Standard size
Tape window facing upward
Inner guides
Medium size (Align the cassette with
the outer guides, then slide it in over
the inner guides.)
Tape window facing upward
No double insertion of cassettes
When you insert a cassette, the orange lock-out plate appears in the cassette
compartment to prevent double insertion.
Ejecting a cassette
Press the EJECT button.
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
EJECT button
Playback
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Playback
Video monitor
2
Player (DSR-1600/1600P)
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
PB FS
48k44.1k32k
1
-60
-60
-60
-60
1 Power on this unit by pressing on the side of the POWER switch.
2 Power on the video monitor and set its switches as shown below.
Switch
Setting
75 Ω termination switch
Input switch
ON (or attach a 75 Ω terminator.)
Set according to the type of input signal from this
unit.
Playback
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Procedure
1
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
REMOTE button
2
Note
When controlling this unit from an editing control unit connected to the
REMOTE connector on this unit, press the REMOTE button to turn it on. When
not, turn the button off.
1 Insert a cassette.
The cassette is automatically drawn into the unit. The STOP button will
light, and a few seconds later a still image will appear on the monitor screen.
2 Press the PLAY button.
This starts the playback operation. When the tape is played back all the way
to the end, the unit automatically rewinds it and then stops.
Playback
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If the following indicators light when a cassette is loaded
Indicator
It means:
Cassette memory indicator The loaded cassette contains a cassette memory.
ClipLink indicator
There is ClipLink log data stored in the cassette
memory on the loaded cassette.
To perform the following operations
Operation
Do this:
Stop playback.
Press the STOP button.
The unit enters stop mode, and will automatically
switch to standby off mode after the time set with the
Adjust the audio playback
level.
Use the audio level control on the monitor.
Play back in shuttle mode
Press the SEARCH button or search dial to light the
while monitoring the video. SHUTTLE indicator in the display section, then rotate
the search dial.
Playback is carried out at the speed determined by
the angular position of the search dial.
The maximum speed for shuttle playback can be
changed using the SHUTTLE menu item (see page
41).
Play back in jog mode while Press the SEARCH button or search dial to light the
monitoring the video.
JOG indicator in the display section, then rotate the
search dial.
Playback is carried out at the speed according to the
speed of the search dial rotation. The playback
speed range is 1 times normal speed by factory
default.
The search dial has no detents.
Inhibit the unit from
outputting text information to OFF.
(time data, operation mode
indications, etc.) to the
video monitor.
Remove the cassette.
Press the EJECT button.
If a CNT value is shown on the time counter display,
the CNT value is reset.
Disable the automatic
rewind function.
DISABLE.
Change the time period
before the unit switches
from stop mode to standby
off mode.
Change the setting of the STOP TIMER menu item
Playback
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback—Automatic Cyclical Playback
Proceed as follows to perform automatic cyclical playback of recording (repeat
playback) between selected start and end points.
1 Set the desired repeat start and end points using the REPEAT FUNCTION
You can set points A and B as start and end points by following the
procedure described in the next section.
The REPEAT indicator lights.
3 Press the SET (YES) button to save the new setting and close the menu.
4 Press the PLAY button.
The unit repeats playback between the repeat start and end points set in step
1.
Setting Points A and B for Repeat Playback
You can set the repeat playback start point (point A) and end point (point B) by
using the current tape position or inputting time code values.
To perform repeat playback after setting points A and B, press the PLAY button
when the REMOTE button is off. When the DSRM-10 Remote Control Unit is
connected to the CONTROL S connector on the front panel, you can also start
repeat playback by pressing its PLAY button with the REMOTE button of this
unit off.
Setting the current tape position as point A or B
Proceed as follows to set the current tape position as point A or B for repeat
playback.
Buttons used for
setting the current
tape position as
point A
A
B
MARK
Buttons used for setting the
current tape position as point B
In the following explanation of how to set points A and B for repeat
playback, these three buttons are referred to as the KA button,
Bk button, and SET (YES)
button, respectively.
MARK
While holding down the SET (YES) MARK button on the menu control panel,
press the KA or Bk button. The time code value of the current tape
position is set as point A or B, and a message “A set” or “B set” is displayed for
0.5 second in the time counter display.
Playback
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Once set, the point A or B time code value is held in the non-volatile memory
of the unit until changed. It is not lost when the unit is powered off.
Note
When setting point A or B, you can only use a time code value. Even when
COUNTER is selected with the COUNTER SEL button, you cannot use a CNT
value to set point A or B.
To check the point A or B time code value
Press the KA or Bk button on the menu control panel. While the button is
held down, the point A or B time code value is displayed on the monitor and in
the time counter display.
If you hold down the KA and Bk buttons simultaneously, the value shown
is the point B time code value minus the point A time code value. If the point A
time code value is greater than the point B time code value, a minus sign (−) is
shown before the value.
Inputting time code values for points A and B
Using the following procedure, you can modify the time code value for point A
or B.
1,15
8,11 12 2,3,4,6,10,11
A
B
MARK
5,7,9,12 13
1 Press the MENU button.
The following menu display appears.
SYSTEM MENU
SETUP MENU
Setup menu
Time counter display
HOURS METER
Monitor screen
Playback
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the Bk button.
The display changes as follows.
SETUP MENU
Operational
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP BANK OPERATION
MENU GRADE
:BASIC
Monitor screen
3 With “OPERATIONAL FUNCTION” selected, press the Bk button.
The display changes as follows.
SETUP MENU
>REP FUNC
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
LOCAL ENABLE :STP&EJ
Monitor screen
4 With “REPEAT FUNCTION” selected, press the Bk button.
The contents of the REPEAT FUNCTION menu item are displayed.
SETUP MENU
>> REPEAT MD
OPERATIONAL FUNCTION
REPEAT FUNCTION
Time counter display
:OFF
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:
T.TOP
V.END
:
B PRESET
Monitor screen
Playback
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Press the j button to select “REPEAT TOP.”
SETUP MENU
>> REP TOP
Time counter display
OPERATIONAL FUNCTION
REPEAT FUNCTION
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
:OFF
:T.TOP
:V.END
B PRESET
Monitor screen
6 Press the Bk button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> Tape top
Time counter display
:T.TOP
REPEAT TOP
* TAPE TOP
A POINT
:V.END
Monitor screen
7 Press the j button to select “A POINT.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>>> A point
Time counter display
REPEAT TOP
:T.TOP
* TAPE TOP :V.END
A POINT
Monitor screen
Playback
28
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Press the KA button.
The display changes as follows.
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> REP TOP
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
9 Press the j button to select “A PRESET.”
SETUP MENU
OPERATIONAL FUNCTION
REPEAT FUNCTION
>> A preset
Time counter display
:OFF
.
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
A
:
V.END
B PRESET
Monitor screen
10Press the Bk button.
The A PRESET MODE screen appears. The time code value of the current
point A is displayed below the screen title.
A PRESET MODE
A
@00:00:00:00
INC/DEC : ( )( )KEY
SHIFT : ( )( )KEY
CLEAR : RESET KEY
DATA SAVE :
SET KEY
TO MENU : MENU KEY
Monitor screen
11Use the KA or Bk button to select the digit in the time code value
display that you want to change.
Each press of the button causes the digit to the left or right to begin flashing.
Holding the button down moves the flashing digit continuously. If you want
to clear the time code value, press the RESET (NO) button. The value is
cleared to 00:00:00:00, and the leftmost digit begins flashing.
Playback
29
Download from Www.Somanuals.com. All Manuals Search And Download.
12Press the J or j button to increment or decrement the value of the flashing
digit.
Each press of the button increments or decrements the value. Holding the
button down increments or decrements the value continuously. To change
other digits, return to step 11.
13Press the SET (YES) MARK button to confirm the defined value.
The message “NOW SAVING...” is displayed on the monitor screen and
“Saving...” is shown in the time counter display while the new setting is
being saved in memory.
Caution
The new setting may be lost if you power off the unit during the saving
operation. Wait until the saving operation is completed before powering off
the unit.
If you want to discard the changed value
Press the MENU button instead of pressing the SET (YES) MARK button
to return to the menu display, then press the MENU button again to end the
menu operation without saving the changed value into memory.
After the saving operation is completed, the monitor screen and time
counter display return to the REPEAT FUNCTION setting display as
shown in step 9.
14To set point B, refer to steps 5 to 13. (Select “REPEAT END” in step 5, “B
POINT” in step 7, and “B PRESET” in step 9.)
15Press the MENU button to close the menu.
Cuing Up to Any Desired Position Set as Point A or B
You can set any desired tape position as point A or B and cue up to the set point
when required. To cue up to point A or B, holding down the KA or Bk
button on the menu control panel, press the REW button in the tape transport
control section.
For the methods of setting points A and B, see the previous section.
Playback
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Convenient Functions
for Editing Operation
Chapter
3
Use the DISPLAY CONTROL menu items (see page 42)
to select the information displayed and the character type
and position of the indications.
Displaying Time Data and
Other Text Information
Monitor screen contents
The contents of the monitor screen are shown below.
This unit allows time data and operation mode indications
to be displayed on the monitor screen.
Time data can also be displayed in the time counter display
on the unit.
A Time data type
Time data
Displaying Time Data and Operation
Mode Indications
B Drop frame indication
a)
for time code reader
The unit is provided with the following functions related to
time data.
• Display and reset CNT value
• Display and play back SMPTE/EBU time code and user
bit data
C VITC field
indication
.
:
T C R
0 0
:
0 4
4 7
0 7
*
• Display and play back VITC
P L A Y
L O C K
The unit can output the time code read from the tape as an
analog (LTC) signal while in normal-speed playback
mode.
D DSR-1600/1600P operation mode
a) This character (.) can appear on the DSR-1600 only. The
character to appear in this column is always a colon ( : ) on the
DSR-1600P.
Note
The unit outputs no signal from the TIME CODE OUT
connector unless it is in normal-speed playback mode.
To view time data and operation mode
indications on the monitor screen
ON (factory default setting).
The time data and the indication of the current operation
mode are superimposed on the video signal that is being
output from the VIDEO OUT 2 (SUPER) connector, and
can be viewed on the monitor screen.
Displaying Time Data and Other Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
31
A Time data type
D DSR-1600/1600P operation mode
The following time data type indications are displayed.
Display
Operation mode
Indication
CNT
Description
CASSETTE OUT
THREADING
UNTHREADING
STANDBY OFF
T. RELEASE
STOP
Cassette is not loaded.
Tape loading
Count value of the time counter
TCR
Time code data from time code reader
(factory default setting)
Tape unloading
Standby off mode
UBR
User bit data from time code reader
Tape tension released
Stop mode
a)
TCR.
Time code data from VITC reader
a)
UBR.
User bit data from VITC reader
F. FWD
Fast forward mode
b)
Time code data from time code reader. The
asterisk indicates an interpolation by the time
code reader to make up for the time code
data not correctly read from the tape.
T*R
REW
Rewind mode
PREROLL
PLAY
Preroll mode
Playback mode (servo unlocked)
Playback mode (servo locked)
Temporary stop of playback
Still picture in jog mode
Jog mode in forward direction
Jog mode in reverse direction
Shuttle mode
b)
User bit data from the time code reader. The
asterisk indicates that last data is retained by
the time code reader, as the new data has
not been read correctly from the tape.
U*R
PLAY LOCK
PLAY-PAUSE
JOG STILL
JOG FWD
JOG REV
a) You can switch between TC and VITC using the TC SELECT menu item
b) “*” is displayed when data cannot be read in correctly.
SHUTTLE (Speed)
B Drop frame indication for time code reader (on
DSR-1600 only)
.
Drop frame mode (factory default setting)
Non-drop frame mode
:
C VITC field indication
(blank)
Display fields 1 and 3.
Display fields 2 and 4.
*
Displaying Time Data and Other Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
32
To display the desired time data in the time
counter display
Time data type indicators
Time counter display
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
COUNTER SEL button
A
B
MARK
Open the door on the lower part of the front panel, and
press the COUNTER SEL button.
Each press of this button cycles through three options:
CNT value, time code, and user bit data. The time data type
indicator for each option lights as it is selected.
Time data
type
indicator
Time data shown in the time counter
display
COUNTER
TC
CNT (count value of the time counter)
Time code
U-BIT
User bit data
Note
When the REMOTE button is lit, the COUNTER SEL
button does not operate while the tape is moving. In such
cases, use the external equipment connected to the
REMOTE connector on the rear panel to select the time
data.
To reset the CNT value
Press the RESET (NO) button on the menu control panel.
This resets the CNT value to 0:00:00:00.
Note
During playback, if the recording on the tape includes
discontinuities, the counter may operate incorrectly at the
corresponding points.
Displaying Time Data and Other Text Information
Download from Www.Somanuals.com. All Manuals Search And Download.
33
External equipment Buttons in the remote control
setting section
High-Speed and Low-
Speed Search—Quickly
and Accurately
Determining Editing
Points
Editing control unit
connected to the
Turn on both the REMOTE and 9PIN
buttons.
REMOTE connector
SIRCS-compatible
remote control unit
connected to the
CONTROL S
Turn off the REMOTE button.
connector
Equipment
Turn on both the REMOTE and
connected to the i.DV i.LINK buttons.
IN/OUT connector
Use the search function to easily locate the desired scene
and to quickly and accurately determine edit points.
For description on how to carry out search operations via
external equipment, see the operating instructions for the
equipment.
Search Operations via External
Equipment
Search Operations on This Unit
You can control the unit in the following operation modes
from an editing control unit (ES-7, PVE-500, etc.)
connected to the REMOTE connector on the rear panel or
from a SIRCS-compatible remote control unit such as the
DSRM-10 connected to the CONTROL S connector on the
front panel.
Shuttle: Use this mode to view color video playback at
speeds ranging from 0 to 60 times normal speed in
both directions.
When you perform searching on this unit, be sure to turn
off the REMOTE button on the front panel.
Playing back in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the search dial. The playback speed range
is 1 times normal speed by factory default. The speed
variation range and pattern can be changed with the JOG
Note
When controlling the unit from the DSRM-10 for
shuttle-mode search, the maximum search speed is 16
times normal speed in both directions.
To carry out playback in jog mode, use the following
procedure.
Jog: Use this mode for low-speed search and frame-by-
JOG indicator
frame search.
Digital slow: Use this mode for noise-free color video
1
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
playback at speeds ranging from 0 to / times normal
2
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
speed in both directions.
Still: Use this mode to view a still picture of any field.
Jog audio: Use this mode to monitor the audio at speeds
1
ranging from 1 to / times normal speed in both
30
directions.
Note
When controlling this unit from external equipment, be
sure to turn on or off the buttons in the remote control
setting section on the front panel as shown in the following
table.
1 1,2,3
1 Press the SEARCH button or search dial so that the
JOG indicator in the display section is lit.
Pressing the search dial toggles between jog mode and
shuttle mode.
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
34
2 Turn the search dial in the desired direction at the
To alternate between normal-speed playback and
shuttle mode playback
speed corresponding to the desired playback speed.
Set the search dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SEARCH buttons alternately.
For intermittent shuttle mode playback, press the STOP
and SEARCH buttons alternately.
Playback in jog mode starts.
3 To stop playback in jog mode, stop turning the search
dial.
Playing back in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the search dial. The range of
playback speed is 32 times normal speed by factory
default. You can change the playback speed range with the
detents at the positions of still image and 10 times normal
speed.
To carry out playback in shuttle mode, use the following
procedure.
SHUTTLE
indicator
OVER
OVER
OVER
OVER
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
dB
0
-12
-20
1
-12
-20
1
-12
-20
1
-12
-20
1
0
-1
-2
1
0
-1
-2
2
0
-1
-2
3
0
-1
-2
4
-30
-40
-30
-40
-30
-40
-30
-40
-60
-60
-60
-60
PB FS
48k44.1k32k
3 1 1,2,3
1 Press the SEARCH button or search dial so that the
SHUTTLE indicator in the display section is lit.
Pressing the search dial toggles between jog mode and
shuttle mode.
2 Turn the search dial to the desired angle corresponding
to the desired playback speed.
Playback in shuttle mode starts.
3 To stop playback in shuttle mode, return the search
dial to the center position, or press the STOP button.
To return to normal-speed playback
Press the PLAY button.
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
35
High-Speed and Low-Speed Search—Quickly and Accurately Determining Editing Points
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Menu Settings
Chapter
4
Menu Organization
As shown in the following figure, the menu system
consists of four levels and is functionally divided into two
subsystems: the setup menu and the digital hours meter
display menu. This chapter mainly describes the setup
menu, showing its contents and how to operate it.
The items of the setup menu are divided into several
functional groups on level 1, and except for the MENU
GRADE item the settings themselves are made on level 2
or level 3.
Also, the menu items are divided into two categories
according to how frequently they are accessed: the “basic”
items, to which frequent access is normally required, and
the “enhanced” items, which are less frequently used. In
the following figure, the items shown in boldface are basic
items, and the other items are enhanced items.
The menu settings are saved in non-volatile memory,
which means they are not erased when you power off the
unit after executing the setting operation.
Menu Organization
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu organization
Menu selection level
Level 1
Level 2
Level 3
REPEAT MODE
REPEAT TOP
REPEAT END
A PRESET
OPERATIONAL FUNCTION
REPEAT FUNCTION
SETUP MENU
B PRESET
LOCAL ENABLE
SEARCH ENABLE
MAX SRCH SPEED
SHUTTLE
F.FWD/REW
JOG RESPONSE
PREROLL TIME
AFTER CUE-UP
PLAY START
AUTO REW
CHARA. DISPLAY
CHARA. POSITION
CHARA. TYPE
CHARA. VSIZE
DISPLAY INFO
MENU DISPLAY
PEAK HOLD
DISPLAY CONTROL
OVER DISP HOLD
BRIGHTNESS
ALARM
REF ALARM
a)
TIME CODE
DF MODE
TC SELECT
VITC POS SEL-1
VITC POS SEL-2
VITC OUTPUT
MUTE IN SRCH
TAPE PROTECTION
VIDEO CONTROL
FROM STOP
FROM STILL
STOP TIMER
STILL TIMER
NEXT MODE
a)
SETUP ADD
CC(F1) BLANK
CC(F2) BLANK
a)
a)
WIDE MODE
ESR MODE
PROCESS CONTROL
CONTROL DEV
C PHASE MODE
ADJ RANGE
VIDEO GAIN
CHROMA GAIN
CHROMA PHASE
a)
b)
SETUP LEVEL
BLACK LEVEL
(Continued)
a) Menu item for DSR-1600 only
b) Menu item for DSR-1600P only
Menu Organization
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu selection level
Level 1
Level 2
Level 3
(Continued)
AUDIO CONTROL
REF LEVEL
OUTPUT LEVEL
LEVEL SELECT
OUTPUT CH3/4
JOG CONTROL
SHUTTLE MUTE
DV PB ATT
SETUP BANK OPERATION
RECALL BANK1
RECALL BANK2
RECALL BANK3
RECALL BANK4
SAVE BANK 1
SAVE BANK 2
SAVE BANK 3
SAVE BANK 4
MENU GRADE
T1:OPERATION
HOURS METER
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
Menu Organization
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Contents
Examples:
Setup Menu
Indication on monitor
screen
Indication in time counter
display
The purpose and settings of the setup menu items are
described below.
OPERATIONAL FUNCTION [Operational]
CASSETTE OUT
[>> Cass. out]
[>>> X32]
Indications of menu items and settings
*X32
• In the table below entitled “Menu contents,” the
indication of each menu item or setting on the monitor
screen is shown first, then the indication of the same item
or setting in the time counter display of this unit is shown
in square brackets ([ ]).
• Settings preceded by an asterisk (such as *X32) are
factory default settings.
• In the time counter display, one to three “>” symbols
may precede item or setting indications depending on the
current menu level. Larger numbers of “>” symbols
indicate lower menu levels.
Menu contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
REPEAT FUNCTION [>REP
FUNC]: Make settings for
repeat playback mode.
REPEAT MODE
[>>REPEAT MD]:
*OFF [>>> OFF]: Do not put the unit into repeat playback
mode.
Determine whether or ON [>>> ON]: Put the unit into repeat playback mode.
not to put the unit into ON (FREEZE) [>>> FREEZE]: Put the unit into freeze
repeat playback mode.
playback mode. In this case, while the unit is cueing up to
the repeat start point, the freeze picture of the repeat end
point is displayed.
REPEAT TOP [>>REP
TOP]: Determine
whether the repeat
start point is the
beginning of tape or
point A.
*TAPE TOP [>>>Tape top]: The repeat start point is the
beginning of tape.
A POINT [>>>A point]: The repeat start point is point A as set
by the user.
REPEAT END [>>REP
*VIDEO END [>>>VD end]: The repeat end point is the end
END]: Determine
of the video recorded portion.
whether the repeat end TAPE END [>>>Tape end]: The repeat end point is the end of
point is the end of the
tape.
video recorded portion, B POINT [>>>B point]: The repeat end point is point B as set
the end of tape or point
B.
by the user.
Specify a time code
value to be used as the
setting of point A.
Specify a time code
value to be used as the
setting of point B.
LOCAL ENABLE [> Local ENA]: Select which of the tape
transport control buttons (EJECT, REW, PLAY, F FWD, and
STOP) operate when the REMOTE button is lit.
ALL DISABLE [>> All DIS]: All of the tape transport control
buttons are disabled.
*STOP & EJECT [>> STOP & EJ]: Only the STOP and
EJECT buttons are enabled.
ALL ENABLE [>> All ENA]: All of the tape transport control
buttons are enabled, and settings such as preroll time
change or time data display selection are effective.
SEARCH ENABLE [>Search ENA]: Select how the unit enters *DIAL DIRECT [>> DIAL]: Press the SEARCH button or,
the search mode.
except during editing, turn the search dial.
VIA SEARCH KEY [>> via KEY]: Press the SEARCH button.
Menu Contents
40
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
MAX SRCH SPEED [>Max
SRCH]: Specify the
SHUTTLE [>>SHUTTLE]: X60 [>>> X60]: Maximum 60 times normal speed
Specify the maximum *X32 [>>> X32]: Maximum 32 times normal speed
maximum tape speed in
search mode (shuttle) and
F.FWD (fast forward)/REW
(rewind) mode.
tape speed in search
mode (shuttle).
X16 [>>> X16]: Maximum 16 times normal speed
F.FWD/REW [>>F.FWD/
MAX [>>> MAX]: No maximum tape speed is specified.
REW]: Specify the
*X85 [>>> X85]: Maximum 85 times normal speed
maximum tape speed X60 [>>> X60]: Maximum 60 times normal speed
in F.FWD/REW mode. X32 [>>> X32]: Maximum 32 times normal speed
Note
When this item is set to MAX, the playback video signal is
muted.
JOG RESPONSE [>JOG dial]: Select the tape speed
*TYPE1 (-1 to +1) [>> type 1]: Tape speed varies linearly
over the range −1 to +1.
characteristics for the search dial rotation rate in jog mode.
TYPE2 (-3 to +3) [>> type 2]: Tape speed varies stepwise as
shown in the figure below over the range −3 to +3.
(Characterized by a zone around −1 and +1 where the
tape speed is independent of the rotation rate)
TYPE3 (-3 to +3) [>> type 3]: Tape speed varies linearly over
the range −3 to +3, as shown in the figure below.
TYPE3
TYPE2
Speed
FWD
Speed
FWD
+3
+3
Rotation rate
FWD
+1
Rotation rate
RVS
RVS
FWD
-1
-3
-3
RVS
RVS
PREROLL TIME [> Preroll]: Set the preroll time.
0 SEC [>> 0 sec] to 15 SEC [>> 15 sec]: The preroll time
can be set in one-second increments to between 0 and 15
seconds.
A preroll time of at least 5 seconds is recommended when
using this unit for editing. When an editing control unit such as
the PVE-500 has been connected, this setting is disabled and
the setting on the editing control unit is in effect. Operations
such as the preroll time setting and the time data switching
operation are also performed on the editing control unit.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
*STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
following cue-up.
PLAY START [> PLAY start]: Set the timing for switching from 16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY [>> 4
stop mode to playback mode.
delay]: The larger the numerical value, the longer the
delay. By adjusting this setting, it is possible to reduce the
phase synchronization time and preroll time during
editing.
In an editing system including an editing control unit such as
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-1600) or 4 FRAME DELAY [>> 4 delay] (for DSR-
1600P)
AUTO REW [>Auto REW]: Select whether to rewind the tape DISABLE [>> DISABLE]: Do not rewind the tape
automatically when recording or playback reaches the end
of a tape.
automatically.
*ENABLE [>> ENABLE]: Rewind the tape automatically.
Menu Contents
41
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not OFF [>> OFF]: Do not output text. (In spite of this setting,
to output text (such as time code values) from the VIDEO
OUT 2 (SUPER) connector.
pressing the MENU button causes menu text to be
output.)
*ON [>> ON]: Output text.
CHARA. POSITION [> Chara pos]: Set the position of text
Use JjKk buttons on the menu control panel to adjust the
superimposed on output from the VIDEO OUT 2 (SUPER) text position while watching the monitor screen.
connector to the monitor.
To return to the level 1 of the setup menu, press the MENU
button.
CHARA. TYPE [> Chara type]: Set the type of characters in
text superimposed on output from the VIDEO OUT 2
(SUPER) connector to the monitor.
Make the following settings while watching the monitor screen.
*WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
CHARA. VSIZE [> Chara size]: Determine the vertical size of *×1 [>> ×1]: Standard size
characters such as time code output from the VIDEO OUT ×2 [>> ×2]: 2 times standard size
2 (SUPER) connector for superimposed display on the
monitor.
DISPLAY INFO [> DISP info]: Select information
superimposed on output from the VIDEO OUT 2 (SUPER)
connector to the monitor.
*TIME DATA & STATUS [>> Time&STA]: Time data and
operating mode indications
TIME DATA & UB [>> Time&UB]: Time data selected using
the COUNTER SEL button, and user bit data (When user
bit data is selected using the COUNTER SEL button, user
bit data and time code are shown.)
TIME DATA & CNT [>> Time&CNT]: Time data selected
using the COUNTER SEL button, and CNT value (When
CNT is selected using the COUNTER SEL button, CNT
value and time code are shown.)
TIME DATA & TIME[>> Time&Time]: Time data and VITC
TIME DATA ONLY [>> Time]: Time data only
REC DATE & TIME [>> REC Date]: The time data selected
with the COUNTER SEL button is shown in the time
counter display, and the date and time of recording are
shown on the monitor screen.
MENU DISPLAY [> Menu DISP]: Set the type of characters in Make the following settings while watching the monitor screen.
menu text superimposed on output from the VIDEO OUT 2 *WHITE (WITH BKGD) [>> White]: White characters on black
(SUPER) connector to the monitor.
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
PEAK HOLD [>Peak hold]: Set the peak hold time for the
OFF [>> OFF] to 1.5 SEC [1.5 sec]: Set the peak hold time in
the range of OFF (no peak hold) to 1.5 seconds in 0.1
second steps.
audio level meters.
Factory default setting: OFF [>> OFF]
OVER DISP HOLD [> Hold OVER]: Determine whether or not *OFF [>> OFF]: Do not hold the OVER indication display.
to hold the OVER indication display on the audio level
meters once the indications light.
ON (HOLD) [>> ON]: Hold the OVER indication display.
Note
With ON selected, once the display is held it will remain held
unless you change the setting to OFF.
BRIGHTNESS [> Brightness]: Set the brightness of front
Set brightness as a percentage of the maximum.
100% [>> 100%]
panel indicators.
*75% [>> 75%]
50% [>> 50%]
Menu Contents
42
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit
Description of settings
ALARM [> ALARM]: Determine whether alarm messages are OFF [>> OFF]: Alarm messages are not issued.
issued or not.
*ON [>> ON]: Alarm messages are issued.
REF ALARM [> REF ALARM]: Determine whether alarm
*OFF [>> OFF]: Alarm messages are not issued.
messages related to reference video signal are issued or ON [>> ON]: Alarm messages are issued.
not.
TIME CODE [Time code]: Settings related to the time code Description of settings
generator
(For DSR-1600 only)
*ON (DF) [>> ON (DF)]: Drop frame mode
OFF (NDF) [>> OFF (NDF)]: Non-drop frame mode
DF MODE [> DF mode]: Select whether the time counter
operate in drop frame mode or non-drop frame mode.
Normally select drop frame mode, to keep in
synchronization with real time. The non-drop frame mode
is useful for example when using computer graphics, and
working on a frame count basis.
TC SELECT [>TC select]: Determine which to display in the
VITC [>> VITC]: Display VITC.
*TC [>> TC]: Display TC.
time counter display, TC or VITC.
VITC POS SEL-1 [>VITC pos-1]: Select a line to insert the
(For DSR-1600)
VITC in.
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
Factory default setting: 16 LINE [>> 16 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-2.
(For DSR-1600P)
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 19 LINE [>> 19 line]
VITC POS SEL-2 [>VITC pos-2]: Select a line to insert the
(For DSR-1600)
VITC in.
12 LINE [>> 12 line] to 20 LINE [>> 20 line]: Select any line
from 12 to 20.
Factory default setting: 18 LINE [>> 18 line]
Note
You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-1.
(For DSR-1600P)
Select a line to insert the VITC in.
9 LINE [>> 9 line] to 22 LINE [>> 22 line]: Select any line
from 9 to 22.
Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [>VITC out]: Select the time code to be output OFF [>> OFF]: Do not output VITC.
as VITC.
TC [>> TC]: Output TC after converting it into VITC.
*VITC [>> VITC]: Output VITC.
MUTE IN SRCH [>Mute in SR]: Select whether to mute the
output from the TIME CODE OUT connector in search
(jog/shuttle) mode.
OFF [>> OFF]: Do not mute.
*ON [>> ON]: Mute.
TAPE PROTECTION [Tape protct]: Settings related to tape Description of settings
and video head protection
FROM STOP [> From STOP]:
Set the time to switch from
stop mode to tape protection
mode.
STOP TIMER [>> STP
timer]: Set the time to
switch from stop mode
to tape protection
mode.
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
Menu Contents
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TAPE PROTECTION [Tape protct]: Settings related to tape Description of settings
and video head protection
FROM STILL [> From STILL]:
Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.
STILL TIMER [>> STL
timer]: Set the time to
switch from still search
mode to tape
5 MIN [>>> 5 min] to 0.5 SEC [>>> 0.5 sec]: Select time from
12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.
Factory default setting: 1MIN [>>> 1min]
protection mode.
1
NEXT MODE [>> Next
mode]: Select the type
of tape protection
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.
*STEP FWD [>>> Step]: The tape is advanced at / times
30
normal speed for about 2 seconds.
STANDBY OFF [>>> STANDBY]: Standby off mode
VIDEO CONTROL [Video]: Settings related to video control Description of settings
(For DSR-1600 only)
*OFF [>> OFF]: Do not add black setup.
SETUP ADD [> Setup add]: Determine whether or not to add ON (ADD) [>> ON]: Add black setup.
black setup to analog video output signals.
(For DSR-1600 only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F1) BLANK [>CC1 blank]: Select whether to mute the
closed caption signal to be superimposed on the 1st field
of the output video signal.
(For DSR-1600 only)
*OFF [>> OFF]: Do not mute.
ON [>> ON]: Mute.
CC(F2) BLANK [>CC2 blank]: Select whether to mute the
closed caption signal to be superimposed on the 2nd field
of the output video signal.
WIDE MODE [>Wide mode]: Determine whether to retain
wide-screen aspect ratio information accompanying video
being played back.
*AUTO [>> Auto]: When video being played back is
accompanied by wide-screen aspect ratio information,
retain the information.
OFF [>> OFF]: Ignore wide-screen aspect ratio information.
ON [>> ON]: Whenever recording or playing back video, retain
wide-screen aspect ratio information.
ESR MODE [>ESR mode]: Select whether to enable the edge *OFF [>> OFF]: Do not enable.
subcarrier reducer (ESR).
ON [>> ON]: Enable.
When playing back a composite signal, set this to ON.
Menu Contents
44
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONTROL [Video]: Settings related to video control Description of settings
PROCESS CONTROL [>Proc
ctrl]
CONTROL DEV [>>Ctrl
dev]: Select the
*REMOTE [>>>REMOTE]: Use the optional UVR-60/60P or
BVR-50/50P Remote Control Unit to remote control the
internal digital video processor.
MENU [>>> MENU]: Use the setup menu to change the
settings for the internal digital video processor.
method of controlling
the internal digital
video processor.
C PHASE MODE [>>C
Phas MD]: Select the
phase rotation mode
for chroma phase
*U/V (COMPOSITE) [>>> Cmpst]: Select this setting when
observing the composite video output level using a
composite vectorscope.
PB/PR (COMPONENT) [>>> Cmpnt]: Select this setting
when observing the component video output level using a
component vectorscope.
control.
The effect of this setting
applies to the output levels
of all of the composite
video, S video, SDI and
component video signals.
ADJ RANGE [>>Adj
range]: Select the
variable range of the
VIDEO and CHROMA
gains.
*−3 to +3 (dB) [>>> −3/+3]: −3 dB to +3 dB
WIDE [>>> wide]: −∞ to +3 dB
VIDEO GAIN [>>V gain]:
00H to 3FFH
Adjust the video output Factory default setting: 200H
level.
CHROMA GAIN [>>C
gain]: Adjust the
00H to 3FFH
Factory default setting: 200H
chroma output level.
CHROMA PHASE [>>C
phase]: Adjust the
chroma phase.
00H to FFH
Factory default setting: 80H
(For DSR-1600 only)
SETUP LEVEL [>>Setup
lev]: Adjust the black
setup level.
00H to 3FFH
Factory default setting: 200H
(For DSR-1600P only)
BLACK LEVEL [>>Black
lev]: Adjust the black
level.
00H to 3FFH
Factory default setting: 200H
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
LEVEL SELECT [>Level Sel]
REF LEVEL [>>REF
Level]: Select the
audio reference level
(headroom).
*−20 dB [>>> −20dB] (factory default setting for DSR-1600)
*−18 dB [>>> −18dB] (factory default setting for DSR-1600P)
−16 dB [>>> −16dB]
−12 dB [>>> −12dB]
OUTPUT LEVEL [>>Out
Level]: Select the
analog audio output
reference level.
*+4 dBm [>>> +4dBm]
0 dBm [>>> 0dBm]
−3 dBm [>>> −3dBm] (for DSR-1600P only)
−6 dBm [>>> −6dBm]
OUTPUT CH3/4 [>OUT ch3/4]: Select the signals to be output *LINE OUT [>> line out]: Output the audio channel-3 and
from the AUDIO OUT CH-3 and AUDIO OUT CH-4
connectors.
audio channel-4 signals from the AUDIO OUT CH-3 and
AUDIO OUT CH-4 connectors as they are.
MONITOR OUT [>> monitor]: Output the monitor audio L-
channel (CH-1) and monitor audio R-channel (CH-2)
signals from the AUDIO OUT CH-3 and AUDIO OUT CH-
4 connectors, respectively.
JOG CONTROL [> Jog ctrl]: Select whether to adjust the
OFF [>> OFF]: Do not adjust the audio playback speed.
*ON [>> ON]: Adjust the audio playback speed.
audio playback speed during slow playback.
Menu Contents
45
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
SHUTTLE MUTE [>Shutl mute]: Set the audio muting
*OFF [>> OFF]: Not muted.
CUEUP or PREROLL [>> CUEUP]: Muted during cue-up or
preroll operations.
conditions during shuttle playback.
FULL [>> FULL]: Muted in shuttle mode.
DV PB ATT [>DV PB ATT]: When playing back a tape
recorded in consumer DV format, select whether to
attenuate the audio output level.
OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.
SETUP BANK OPERATION [Setup Bank]: Settings related Description of settings
to menu bank operations
RECALL BANK1 [>Recall 1]: Recall menu settings from
(1) Select the bank you want to recall, then press the k
menu bank 1.
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [>Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [>Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [>Recall 4]: Recall menu settings from
menu bank 4.
SAVE BANK 1 [>Save 1]: Save current menu settings to menu (1) Select the bank you want to save, then press the k
bank 1.
button.
Message “SAVE OK?” appears.
(2) To save, press the SET (YES) button.
To quit saving, press the RESET (NO) button.
SAVE BANK 2 [>Save 2]: Save current menu settings to menu
bank 2.
SAVE BANK 3 [>Save 3]: Save current menu settings to menu
bank 3.
SAVE BANK 4 [>Save 4]: Save current menu settings to menu
bank 4.
Menu banks
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered 1 to 4.
Saved sets of menu settings can be recalled for use as required.
MENU GRADE [Menu grade]: Selection of menu items to
be displayed
Description of settings
Determine whether to display basic items only or both basic
and enhanced items on the monitor screen and in the time
counter display when using the menu.
*BASIC [> Basic]: Display basic items only.
ENHANCED [> Enhanced]: Display both basic and enhanced
items.
Menu Contents
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Basic
Items
Changing Menu Settings
The factory default setting is to display only the basic
items. To change the settings of basic items proceed as
follows.
This section explains how to change menu settings.
Buttons Used to Change Settings
Use the following buttons on the menu control panel to
change the menu settings.
1
3,5,7
Menu control buttons
Functions
MENU button
• Opens the menu and
launches menu control
mode.
2,4,6
• Closes the menu and exits
menu control mode.
A
B
J and j buttons
These buttons move the
highlighted cursor up and
down within the current level
to select an item or setting.
Hold down one of these
buttons to make the
MARK
9
8
highlighted cursor move
continuously.
1 Press the MENU button on the menu control panel.
K and k buttons
• Press the k button to go
down one level.
• Press the K button to go
up one level.
The menu selection level display appears on the
monitor. In the figure below, “SETUP MENU” is
selected (shown in reverse video).
Hold down one of these
buttons to make the
highlighted cursor move
continuously.
The time counter display of this unit shows only the
currently selected item. When the item name is long, it
is abbreviated.
RESET (NO) button
SET (YES) button
• Returns the setting to the
factory default setting.
• Sends a negative
response to prompts on
the monitor screen.
Menu selection level display
SYSTEM MENU
Setup menu
SETUP MENU
HOURS METER
Time counter display
• Saves the new setting in
memory.
• Sends a positive response
to prompts on the monitor
screen.
Monitor screen
Changing Menu Settings
47
Download from Www.Somanuals.com. All Manuals Search And Download.
2 With “SETUP MENU” selected, press the k button.
5 Press the J or j button to select the item whose
setting you wish to change.
This displays all items on menu level 1.
For menu items on level 3, press the k button to go
to the level 3, then press the J or j button to select the
item whose setting you wish to change.
Level-1 menu display
SETUP MENU
Operational
OPERATIONAL FUNCTION
Example: Display when “BRIGHTNESS” is selected
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP MENU
> Brightness
DISPLAY CONTROL
SETUP BANK OPERATION
CHARA.DISPLAY :ON
MENU GRADE
:BASIC
Time counter display
CHARA.POSITION
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
:T&STA
:WHITE
:OFF
Monitor screen
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
3 Press the J or j button to select the required item.
Monitor screen
Example: Display when “DISPLAY CONTROL” is selected
6 Press the k button.
SETUP MENU
Display
This displays all possible settings for the item selected
in step 5.
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
SETUP BANK OPERATION
SETUP MENU
>> 75%
MENU GRADE
:BASIC
DISPLAY CONTROL
BRIGHTNESS
100%
:75%
Time counter display
* 75%
50%
Monitor screen
4 Press the k button.
Monitor screen
This displays the menu level 2 for the menu item
selected in step 3.
7 Press the J or j button to change the setting of the
Example: Level-2 display for “DISPLAY CONTROL”
item.
SETUP MENU
> Chara disp
DISPLAY CONTROL
CHARA.DISPLAY :ON
Time counter display
SETUP MENU
>> 50%
CHARA.POSITION
DISPLAY CONTROL
CHARA.TYPE
CHARA.VSIZE
DISPLAY INFO
MENU DISPLAY
PEAK HOLD
:WHITE
:x1
BRIGHTNESS
100%
:75%
Time counter display
:T&STA
:WHITE
:OFF
Current settings
* 75%
50%
OVER DISP HOLD :OFF
BRIGHTNESS :75%
ALARM :ON
Monitor screen
Monitor screen
Changing Menu Settings
48
Download from Www.Somanuals.com. All Manuals Search And Download.
8 To change other settings, press the K button to return
to the previous screen, then repeat steps 5 to 7 as
required.
Displaying Enhanced Items
The factory default setting is not to display enhanced
items.
9 When you have completed the settings, press the SET
To display enhanced items, set the MENU GRADE menu
procedure in the previous section “Changing the Settings
of Basic Items.” (In step 3, first select “MENU GRADE,”
and next select “ENHANCED,” then press the SET (YES)
button to save the setting in memory.)
(YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
With this done, when you press the MENU button and the
k button to display the setup menu, all basic and
enhanced items in the menu level 1 appear.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
Notes
Changing the Settings of Enhanced
Items
• If you power off the unit before saving operation is
completed, settings may be lost. Wait until the
saving is completed before powering off the unit.
• If, instead of pressing the SET (YES) button, you
press the MENU button, the new settings are not
saved. The message “ABORT!” appears on the
monitor screen and “Abort!” in the time counter
display for about 0.5 second, and the system exits
the menus. To change more than one setting, be sure
to press the SET (YES) button after making the
settings.
To change the settings of enhanced items, first carry out
the procedure in the previous section “Displaying
Enhanced Items,” then proceed as follows.
2
1
A
B
Meanings of indications on the monitor
screen
MARK
On-screen indication
Meaning
3
4
Right-pointing arrow (k) at
the right of a menu item
See step 1 of the foregoing
operating procedure.
Pressing the k button
switches to the next lower
menu level or to a setting
selection screen.
1 Press the MENU button on the menu control panel.
Left-pointing arrow (K) at
the left of a menu item
See step 4 of the foregoing
operating procedure.
Pressing the K button
returns to the previous
(higher) menu level.
The menu selection level display appears on the
monitor.
2 With “SETUP MENU” selected, press the k button.
Character string at the right of Current setting of the menu
a menu item
item.
This displays all basic and enhanced items on menu
level 1.
See step 4 of the foregoing
operating procedure.
• When shown with a colon
(:): the current setting is
the same as the factory
default setting.
Level-1 menu display
• When shown with a raised
dot (•): the current setting
is different from the factory
default setting.
SETUP MENU
Menu grade
OPERATIONAL FUNCTION
DISPLAY CONTROL
Time counter display
TIME CODE
See step 2 of the operating
TAPE PROTECTION
VIDEO CONTROL
AUDIO CONTROL
SETUP BANK OPERATION
An asterisk in a complete list Factory default setting.
of settings
ENHAN
MENU GRADE
See step 6 of the foregoing
operating procedure.
Current setting
Monitor screen
Changing Menu Settings
49
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Follow the same procedure as in steps 3 to 8 of the
select an item and change its setting.
4 Press the SET (YES) button.
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
4 When you have completed the settings, press the SET
(YES) button.
Note
The message “NOW SAVING...” appears on the
monitor screen, and “Saving...” appears in the time
counter display, while the new settings are saved in
memory.
When the saving operation is completed, the monitor
screen and time counter display return to their normal
indications.
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the saving is
completed before powering off the unit.
To abandon the resetting operation
Instead of pressing the SET (YES) button, press the
RESET (NO) button. The display returns to menu
level 1, leaving the settings unchanged.
Returning Menu Settings to Their
Factory Default Settings
After making menu setting changes, to return settings to
their factory default settings (setting initialization), use the
following procedure.
To return a particular setting to its factory
default setting
In the display for changing the target setting, press the
RESET (NO) button.
the current setting displayed (in the example, if the setting
has been changed it will be “100%” or “50%”), press the
RESET (NO) button. The setting returns to its factory
default setting of “75%.”
To return all settings to their factory
default settings
Use the following procedure.
1 Press the MENU button on the menu control panel to
display the menu selection.
2 Press the k button to display level 1 of the setup
menu.
3 Press the RESET (NO) button.
A message appears, to confirm whether or not you
wish to return all settings to their factory default
settings.
Monitorscreen
message
“INITIALIZE ALL ITEMS TO
FACTORY PRESET VALUES?”
Message in the time “Init setup?”
counter display
Changing Menu Settings
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and
Settings
Chapter
5
Connections for a Digital Non-Linear Editing System
This unit can be connected to an ES-7 EditStation to
configure a digital non-linear editing system.
If you use the SDTI (QSDI) interface with the optional
DSBK-1602 board installed in the unit, you can transfer
video, audio, time code, and other compressed data from
this unit to the ES-7.
The unit supports ClipLink functions, enabling index
pictures recorded on tape and ClipLink log data stored in
cassette memory to be transferred to the ES-7 in an instant.
For a general description of ClipLink functions, see the
The following figure shows a connection diagram for a
non-linear editing system in which this unit serves as the
player.
For connections of the ES-7 and its peripheral devices
such as the ESBK-7011 Control Panel, the ESBK-7045
Disk Unit, etc., refer to your ES-7 Operating Instructions.
Note
The example connections shown in this chapter assume
that the optional DSBK-1601/1602/1803 and DSBK-1801/
1802/1803 boards are installed as required on the DSR-
1600/1600P and DSR-1800/1800P, respectively.
Connections for a Digital Non-Linear Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
51
REF.
VIDEO
IN
B B OUT(1/2/3/4)
1
SDTI(QSDI)OUT
QSDI INPUT
PLAYER
1
2
REMOTE
VIDEO OUT 2
(SUPER)
AUDIO
MONITOR OUT
DSR-1600/1600P
ES-7 EditStation
1
3
Composite
video input
Audio input
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
Video monitor
Settings on the DSR-1600/1600P
Button
Setting
REMOTE
On (lit)
Connections for a Digital Non-Linear Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Connections for a Cut Editing System
The following figure shows a cut editing system
configuration which includes a DSR-1600/1600P unit as
the player and a DSR-1800/1800P as the recorder.
For details of connecting devices other than the DSR-
1600/1600P, refer to the instruction manual for each
device.
A 75 Ω coaxial cable (not supplied)
B 9-pin remote control cable
(not supplied)
C Cable with RCA phono plugs
(not supplied)
1
DSR-1600/1600P
(player)
DSR-1800/1800P
(recorder)
SDTI(QSDI)IN
SDTI(QSDI)OUT
REF.
VIDEO
OUT
VIDEO
OUT 2
(SUPER)
AUDIO
MONITOR
OUT
AUDIO
MONITOR
OUT
VIDEO
OUT 2
(SUPER)
REMOTE
REMOTE
1
3
2
1
1
3
2
Composite
video input
Composite
video input
Audio input
Audio input
REF.
VIDEO IN
PLAYER
Source monitor
Main monitor
RECORDER
Editing control unit (RM-450/
a)
450CE, PVE-500, etc.)
a) For the settings on the editing control unit, see
Settings on the DSR-1600/1600P (player) and
DSR-1800/1800P (recorder)
About reference video signals
In order to provide stable video and audio signals for
analog editing, it is necessary for the built-in time base
corrector (TBC) to operate correctly. To ensure this, input
a reference video signal synchronized with the video signal
to the REF. VIDEO IN connector.
Button
REMOTE
9PIN
Recorder
On (lit)
Player
On (lit)
On (lit)
On (lit)
For details of the video/audio input and audio mode
settings for the recorder, refer to the DSR-1800/1800P
Operating Instructions.
Connections for a Cut Editing System
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for an A/B Roll Editing System
The following is an example configuration of A/B roll
editing system using the DSR-1600/1600P.
In this configuration, the recorder is a DSR-1800/1800P
unit, player 1 is a DSR-1600/1600P unit, and player 2 is an
analog Betacam UVW-1600/1600P Videocassette Player
unit. To create a final tape (a tape that contains a
completely packaged program) in Betacam format, use a
Betacam VCR such as the UVW-1800/1800P as the
recorder.
The purpose of the following figure is to clearly indicate
the flow of signals among the component devices in this
system. The specific connections and settings are
Connections for an A/B Roll Editing System
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Source video monitor
Main video monitor
Audio system monitor
Video signal generator
(Sony Tektronix TSG-
130, etc.)
DSR-1800/1800P
(recorder)
DPS-D7 or other delay
a)
unit
MXP-290Audio
Mixer
PVE-500, etc. (editing control unit)
DFS-500/500P
DME Switcher
UVW-1600/1600P
(player 2)
DSR-1600/1600P (player 1)
Video signal
Audio signal
Reference video signal
Control signal
a) When using a DFS-500/500P DME Switcher, the phase of the video signals processed
by the DFS-500/500P is delayed. It is therefore necessary to connect a delay unit
between the MXP-290 Audio Mixer’s output and the audio input to the DSR-1800/1800P
(recorder).
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Audio monitor system connections
Reference video signal connection
The following shows an example of audio monitor system
connections.
When you perform recording, be sure to input a reference
video signal.
For details of these connections, refer to the instruction
manual for each connected device.
Speaker (right channel)
Speaker (left channel)
DFS-500/500P DME Switcher
BLACK
BURST
4 3 2 1
OUT
Audio amplifier
DSR-1800/1800P
(recorder)
REF. VIDEO IN
R
R
L
L
Cables with RCA phono plugs
MONITOR
OUT 1
MONITOR
OUT 2
DSR-1600/1600P
(player 1)
REF. VIDEO IN
MXP-290 Audio Mixer
REF. VIDEO IN 75 Ω
termination switch: ON
UVW-1600/1600P
(player 2)
REF. VIDEO IN
PVE-500 Editing Control Unit
REF.
VIDEO
IN
REF. VIDEO IN 75 Ω termination switch: ON
Use 75 Ω coaxial cables for all of these connections.
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Control signal connections
The following shows an example of control signal
connections to enable the editing control unit to control all
other A/B roll editing system devices.
DSR-1800/1800P (recorder)
REMOTE
a)
9-pin remote control cable
DSR-1600/1600P (player 1)
REMOTE
Mixer control mode
selection switch:
PARALLEL
UVW-1600/1600P (player 2)
PVE-500 Editing
Control Unit
RECORDER
PLAYER 1
MIXER
SWITCHER
PLAYER 2
REMOTE
a)
9-pin remote control cable
DFS-500/500P DME Switcher
a)
EDITOR
9-pin remote control cable
MXP-290 Audio Mixer
9-pin/15-pin mixer control cable (not supplied)
EDITOR (15-pin)
a) For the 9-pin remote control cable, use an optional
RCC-5G/10G/30G cable.
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
57
In this example, analog component signals are used as the
video signals and XLR 3-pin connectors are used as audio
input/output connectors.
Video/audio signal connections
The following shows an example of video/audio signal
connections in an A/B roll editing system.
DSR-1800/1800P
(recorder)
COMPONENT VIDEO IN
Y, R–Y, B–Y
1
VIDEO INPUTS
DFS-500/500P DME Switcher
COMPONENT 2
PGM OUT
COMPONENT 1
CH-2
AUDIO IN
CH-1
3
VIDEO INPUTS
COMPONENT 1
1
3
CH-1 OUT
DPS-D7 or other delay unit
CH-1 IN CH-2 IN
CH-2 OUT
2
DSR-1600/1600P
(player 1)
COMPONENT VIDEO OUT
Y, R–Y, B–Y
3
3
LINE OUT 2
LINE OUT 1
AUDIO OUT
CH-1
MIC/LINE 4
IN
3
2
1
MXP-290
Audio Mixer
CH-2
3
3
3
3
COMPONENT 1
OUTPUT
A 12-pin/3-BNC cross
cable
(not supplied; consult
your Sony dealer about
this cable.)
B 12-pin dubbing cable
AUDIO OUTPUT
CH-1
(not supplied)
UVW-1600/1600P (player 2)
CH-2
C Cable with XLR
connectors (not
supplied)
Settings on the DSR-1800/1800P
Switch/menu
Setting
AUDIO IN LEVEL/600 Ω
HIGH-ON
switches
For details of the video/audio input and audio mode
settings, refer to the instruction manuals for the devices
used.
Connections for an A/B Roll Editing System
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection of a video monitor
Settings on an editing control unit
Set up the following connections to enable monitoring of
video and audio signals on a video monitor. In addition to
the video and audio signals, you can have time data, the
operation mode of the unit, alarm messages, and other
information displayed as text on the monitor screen by
setting the CHARA. DISPLAY menu item (see page 42)
to ON (factory default setting).
When connecting an editing control unit, make the settings
as follows, according to the model.
PVE-500
No settings are required.
BVE-600/900/910/2000 (NTSC model) or FXE-100/
120
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
75 Ω termination switch: ON (or
attach a 75 Ω terminator.)
Input switches: Set according to the
type of input signals.
80 16 00 96 05 05 03 80 0A 08 FE 00 80 5A FF
BVE-600/900/910/2000 (PAL model) or FXE-100P/
120P
Video monitor
Set the VCR constants as follows.
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
81 16 00 7D 05 05 02 80 0A 07 FE 00 80 4C FF
RM-450/RM-450CE
Set the DIP switches as follows.
• Left switches
Composite
Audio input
7
6
5
4
3
2
1
0
video input
OFF
−
−
OFF
−
−
−
−
VIDEO
OUT
2(SUPER)
• Right switches (RM-450)
2
1
)
AUDIO
MONITOR OUT
7
6
5
4
3
2
1
0
OFF
−
OFF
ON
OFF
OFF
ON
ON
• Right switches (RM-450CE)
7
6
5
4
3
2
1
0
ON
−
OFF
ON
OFF
OFF
ON
ON
BVE-800
Set the DIP switches as follows.
DSR-1600/1600P
• SW2
1
2
3
4
5
6
7
8
A Cable with RCA phono plugs
ON
OFF
ON
ON
−
ON
ON
−
(not supplied)
• SW3 (NTSC model)
B 75 Ω coaxial cable
(not supplied)
1
2
3
4
5
6
7
8
ON
ON
ON
OFF
−
ON
OFF
OFF
• SW3 (PAL model)
1
2
3
4
5
6
7
8
OFF
OFF
OFF
ON
−
ON
OFF
OFF
Connections for an A/B Roll Editing System
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Adjusting the Sync and Subcarrier Phases
When using two or more players, as in an A/B roll editing
system, it is necessary to synchronize the sync and
subcarrier (for composite signals) phases of the signals to
be edited. If they are not synchronized, picture instabilities
or color break-up may occur at edit points.
After configuring the editing system, use a vectorscope to
adjust the sync and subcarrier phase of the recorder and
players. Subcarrier phase adjustment is necessary when
using composite signals and Y/C signals.
DSR-1600/1600P (player 1)
a)
Switcher (DFS-500/500P)
DSR-1800/1800P (recorder)
UVW-1600/1600P (player 2)
b)
75 Ω coaxial cable (A)
b)
75 Ω coaxial cable (B)
Vectorscope (Sony Tektronix
1750/1751, etc.)
PVE-500 Editing
Control Unit
a) The sync and subcarrier phase of the
output signal from the DFS-500/500P
switcher are automatically adjusted.
b) Ensure that the 75 Ω coaxial cables (A) and
(B) (not supplied) are of the same length.
Adjusting the Sync and Subcarrier Phases
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing a phase adjustment operation
Note
When component signals are used the subcarrier phase
indicator does not appear.
1 Press the SCH button on the vectorscope.
The vectorscope switches to SCH mode.
8 Output the player 2 signal from the PVE-500, and
repeat steps 6 and 7 to adjust the sync and subcarrier
phases of the output from player 2.
2 Press the B channel button on the vectorscope.
This displays the black burst signal from the switcher.
3 Press the EXT button on the vectorscope.
This switches the vectorscope to external
synchronization mode.
4 Adjust the phase synchronization control on the
vectorscope so that the sync and subcarrier phases are
close to the reference line.
Sync phase
Subcarrier phase
Reference line
Align the sync and subcarrier phases of the black
burst signal to the reference line.
5 Output the player 1 signal from the PVE-500.
6 Press the A channel button on the vectorscope.
This displays the sync and subcarrier phases
(composite signals only) of the signal from player 1.
7 On player 1, adjust the SYNC PHASE and SC PHASE
controls on the menu control panel, using a Phillips
screwdriver, so that the output from player 1 on
channel A is in correct phase alignment with the black
burst signal on channel B.
This indicator
This indicator
moves as you
moves as you
turn the SYNC
turn the SC
PHASE control.
PHASE control.
Adjust the sync and subcarrier phases of the output
signal from player 1.
Adjusting the Sync and Subcarrier Phases
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Adjusting the Sync and Subcarrier Phases
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Maintenance and
Troubleshooting
Chapter
6
Regular Checks
Maintenance
Digital hours meter
The digital hours meter keeps cumulative counts of the
total operating time, the head drum rotation time, the tape
transport operating time, and the number of threading/
unthreading operations. These counts can be displayed on
the monitor screen and in the time counter display of this
unit. Use them as guidelines for scheduling maintenance.
In general, consult your Sony dealer about necessary
periodic maintenance checks.
Condensation
If you move the unit suddenly from a cold to a warm
location, or if you use it in a very humid place, moisture
from the air may condense on the head drum. This is called
condensation, and if a tape is run in this state, the tape may
stick to the drum and can be easily damaged. To lessen the
risk of this occurring, this unit is equipped with a
condensation detection system.
Digital hours meter display modes
The digital hours meter has the following four display
modes.
If condensation occurs while the unit is
operating:
• T1 (OPERATION) mode
The alarm message “MOISTURE HAS BEEN
DETECTED.” appears on the monitor screen, and the
alarm message “HUMID!” in the time counter display. At
the same time the unit ejects the cassette automatically. If
this happens, leave the unit powered on and wait until the
alarm messages disappear.
The cumulative total hours during which the unit is
powered on is displayed in 10-hour increments.
• T2 (DRUM ROTATION) mode
The cumulative total hours of drum rotation with tape
threaded is displayed in 10-hour increments.
• T3 (TAPE RUNNING) mode
The cumulative total hours of tape transport operation
for fast forward, rewind, playback, and search (except in
still search mode) is displayed in 10-hour increments.
• CT (THREADING) mode
The cumulative number of tape threading/unthreading
operation pairs is displayed in 10-operation pair
increments.
If the condensation alarm message appears
immediately after powering on:
Leave the unit powered on and wait until the alarm
message disappears. You cannot load a cassette into the
unit while the alarm message is being displayed.
Once the alarm message disappears, the unit is ready for
use.
For all modes except T1 (OPERATION), there are two
types of count: a “trip” count, which is resettable, and the
cumulative total from manufacture, which is unresettable.
Maintenance
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital hours meter indications on the monitor
screen
All four counts (T1, T2, T3, and CT) are indicated on the
monitor screen.
Displaying the digital hours meter
Use the following procedure.
1 Press the MENU button on the menu control panel.
The menu selection level display appears on the
monitor screen and in the time counter display.
Resettable trip counts
Unresettable counts
HOURS METER
Menu selection level display
T1
00000 X10 HOURS
T2 0000/00000 X10 HOURS
T3 0000/00000 X10 HOURS
CT 0000/00000 X10 COUNT
SYSTEM MENU
Setup menu
SETUP MENU
HOURS METER
Time counter display
T1:OPERATION
T2:DRUM ROTATION
T3:TAPE RUNNING
CT:THREADING
Monitor screen
The four-digit value to the left of the slash (/) is the
resettable trip count, and the right value is the cumulative
total from manufacture.
2 Press the j button to select “HOURS METER.”
Digital hours meter indications in the time
counter display
SYSTEM MENU
Hours meter
SETUP MENU
One of the four indications appears in the time counter
display at a time. Use the J and j buttons on the menu
control panel to change the item displayed.
Initially, only the trip value appears. Hold down the k
button to display also the cumulative total from
manufacture, which will appear to the right of the trip
value and the slash (/).
HOURS METER
Time counter display
The following illustrates the digital hours meter
indications in the time counter display in all four display
modes. The right-hand indication for each display mode is
the indication you can view while holding down the k
button on the menu control panel.
Monitor screen
3 Press the k button.
The cumulative counts by the digital hours meter are
indicated on the monitor screen and in the time counter
display.
T1 (OPERATION) mode:
Oper. 00000
T2 (DRUM ROTATION) mode:
Drum 0000
0000/00000
0000/00000
0000/00000
T3 (TAPE RUNNING) mode:
Tape 0000
CT (THREADING) mode:
Thread 0000
Maintenance
64
Download from Www.Somanuals.com. All Manuals Search And Download.
To end the digital hours meter display
Press the MENU button on the menu control panel.
To reset the trip values
About this operation, consult your Sony dealer.
Head Cleaning
Always use the DVM12CL (mini size) or DV12CL
(standard size) Cleaning Cassette to clean the video and
audio heads. You can run the cleaning cassette for 10
seconds per cleaning operation. Follow the instructions for
the cleaning cassette, as inappropriate use of the cleaning
cassette can damage the heads.
To clean the heads
Insert the cleaning cassette. This automatically starts
cleaning. You cannot operate any tape transport control
buttons other than the EJECT button during the cleaning
operation.
After about 10 seconds, the cleaning cassette will be
automatically ejected.
Maintenance
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If an alarm message appears on the monitor screen, or if
the unit appears to be malfunctioning, please check the
following before contacting your Sony dealer.
Tape problem
Symptom
Cause
Remedy
The unit’s tape
transport control
buttons (PLAY, F FWD,
REW, etc.) do not
work.
The REMOTE button is lit and the
LOCAL ENABLE menu item is set to
STOP & EJECT or ALL DISABLE.
Press the REMOTE button to turn it off, or change the setting
ENABLE.
a)
a)
No cassette is loaded.
a) In these states, an alarm message appears on the monitor screen and in the
time counter display.
Time data problem
Symptom
Cause
Remedy
The tape is running,
but the time data is not
shown in the time
counter display.
The U-BIT time data type indicator is lit. Press the COUNTER SEL button to make the COUNTER or
TC time data type indicator light up.
Monitor problems
Symptom
Cause
Remedy
Data is not
superimposed on the
monitor screen.
The CHARA. DISPLAY menu item is
set to OFF.
The monitor is not connected to the
VIDEO OUT 2 (SUPER) connector of
this unit.
Connect the monitor to the VIDEO OUT 2 (SUPER)
connector. (You must make this connection to display any
type of text on the monitor.)
The image on the
monitor screen is too
bright.
The 75 Ω termination switch for video
input on the monitor is in the OFF
position, or a 75 Ω terminator is not
fitted to its video input connector.
Set the 75 Ω termination switch to ON or connect a
terminator.
The image on the
monitor screen is too
dark.
In a video signal loop-through
Set the 75 Ω termination switches to OFF on all monitors
other than the loop-end monitor.
connection of video monitors, 75 Ω
termination switches for video input on
monitors other than the loop-end
monitor are in the ON position.
Troubleshooting
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
This unit is provided with a self-diagnostic function that
detects internal abnormalities. When it detects an
abnormality, it outputs an error message to the monitor
screen and indicates an error code in the time counter
display.
Note
To display error messages on the monitor screen, connect
the monitor to the VIDEO OUT 2 (SUPER) connector, and
ON (factory default setting).
ERROR
AN ERROR HAS BEEN
DETECTED. INFORM SERVICE
OF FOLLOWING CODE:
02-603
Error message
Error code
PRESS EJECT KEY
TO EJECT TAPE.
Direction
Error code
Error02-603
Time counter display
Monitor screen
If an error message appears, follow the direction indicated
on the monitor screen.
Alarm Messages
When operating this unit, the unit may sometimes output
alarm messages such as the one shown below to the
monitor screen and the time counter display.
ALARM
Cause of
alarm
REMOTE MODE IS SELECTED
Direction
PRESS REMOTE BUTTON
TURNING IT OFF
REMOTE!
Monitor screen
Time counter display
If such an alarm message appears, a connection or
operation error may have been made, or condensation on
heads may have occurred. Follow the direction indicated
on the monitor screen.
Note
To display alarm messages on the monitor screen, it is
necessary for the monitor to be connected to the VIDEO
OUT 2 (SUPER) connector, and set the following menu
items to ON.
Troubleshooting
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm messages and associated directions
Direction
Alarm message on monitor screen
(Cause)
Alarm message in time
counter display
A cleaning tape has been inserted.
The tape will automatically be ejected after cleaning is Cleaning Tp
completed.
Abnormal settings selected in setup
menu.
Correct the setup menu settings. Contact your Sony
dealer if this alarm message appears again after
making corrections.
ILL. SETUP!
Cassette adaptor not usable.
Moisture has been detected.
Use a tape without cassette adaptor.
Adaptor!
Keep the power on and wait until this alarm message HUMID!
disappears.
No cassette in VTR.
Load a cassette.
No Cass.!
REMOTE!
Remote mode is selected.
Tape cannot be replayed.
Turn off the REMOTE button.
Use a tape recorded in 525/60 format. (For DSR-
1600)
625/50 Tape
(For DSR-1600)
Use a tape recorded in 625/50 format. (For DSR-
1600P)
525/60 Tape
(For DSR-1600P)
Tape end has been detected.
Tape not usable.
Use a new cleaning tape.
Tape end!
ILL. Tape!
Use a DVCAM/DV/DVCPRO (25M) tape.
Troubleshooting
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendixes
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent shock
to it, is likely to cause it to malfunction.
Precautions
Do not obstruct ventilation openings
To prevent the unit from overheating, do not obstruct
ventilation openings, by for example wrapping the unit in
a cloth while it is in operation.
On safety
• Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be used
for an extended period of time.
On cleaning
If the casing or panel is dirty, wipe it gently with a soft dry
cloth. In the event of extreme dirt, use a cloth steeped in a
neutral detergent to remove the dirt, then wipe with a dry
cloth. Applying alcohol, thinners, insecticides, or other
volatile solvents may result in deforming the casing or
damaging the finish.
• To disconnect the cord, pull it out by the plug. Never pull
the cord itself.
On operation and storage locations
Avoid operation or storage in any of the following places.
• Location subject to extremes of temperature (operating
temperature range 5ºC to 40ºC (41ºF to 104ºF))
• Location subject to direct sunlight for long periods, or
close to heating appliances (Note that the interior of a car
left in summer with the windows closed can exceed 50ºC
(122ºF).)
On repacking and shipping
Save the original shipping carton and packing material;
they will come in handy if you ever have to ship your unit.
For maximum protection, repack your unit as it was
originally packed at the factory, and take care not to impart
violent shocks in transit.
• Damp or dusty places
• Location subject to severe vibrations
• Location near equipment generating strong
electromagnetic emissions
• Location near transmitting stations generating strong
radio waves
Operate the unit in a horizontal position
This unit is designed to be operated in a horizontal
position. Do not operate it on its side, or tilted through an
excessive angle (exceeding 20º).
Precautions
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions (w/h/d, excluding projections)
427 × 174 × 400 mm
Specifications
7
7
3
(16 / × 6 / × 15 / inches)
8
8
4
General
427(16 7/8)
Signal system DSR-1600: NTSC
DSR-1600P: PAL
Power requirements
100 V to 240 V AC, 50/60 Hz
Power consumption (with all options installed)
DSR-1600:
70 W/120 V
DSR-1600P for Europe:
70 W/220 V
Peak inrush current
(1)Power ON, current probe method:
40 A (100 V), 40 A (240 V)
(2)Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
40A (230 V)
Operating temperature
5ºC to 40ºC (41ºF to 104ºF)
Storage temperature
372(14 3/4)
−20ºC to +60ºC (−4ºF to +140ºF)
Operating relative humidity
Less than 80%
Unit: mm (inches)
Storage relative humidity
Less than 90%
Tape transport control system
Mass
13 kg (28 lb 10 oz)
Tape speed
DSR-1600: 28.193 mm/s
DSR-1600P: 28.221 mm/s
Playback time
Using PDV-184ME standard-size
cassette:
Maximum 184 minutes
Using PDVM-40ME mini-size cassette:
Maximum 40 minutes
Fast forward/rewind time
Using PDV-184ME standard-size
cassette:
Less than 3 minutes
Using PDVM-40ME mini-size cassette:
Less than 1 minute
Search speed
When controlling via RS-422A interface:
Maximum 60 times normal speed in
both directions
When controlling from DSRM-10
Remote Control Unit:
Jog mode: 0 (still) to 2 times normal
speed in both directions
Shuttle mode: 8 speeds from 0 (still) to
16 times normal speed in both
directions
Specifications
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Video performance
Input connectors
Band width
Composite (DSR-1600):
Analog video inputs
REF. VIDEO IN
30 Hz to 4.2 MHz 1.0 dB (Y)
Composite (DSR-1600P):
25 Hz to 4.8 MHz 1.0 dB (Y)
S-video (DSR-1600):
30 Hz to 5.0 MHz 1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
S-video (DSR-1600P):
BNC type (×2, loop-through)
Black burst
0.286 V (DSR-1600) or 0.3 V (DSR-
1600P), 75 Ω, negative sync
Composite sync
25 Hz to 5.0 MHz 1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM)
Component (DSR-1600):
Output connectors
Digital signal outputs
SDTI (QSDI) OUT (with optional DSBK-1602 SDTI
(QSDI) Output Board installed)
BNC type, SDTI (QSDI) format (270
Mbps)
SDI OUT (with optional DSBK-1601 SDI/AES/EBU
Output Board installed)
30 Hz to 5.0 MHz 1.0 dB (Y),
5.75 MHz +0/−3.0 dB (Y) (TM),
30 Hz to 1.3 MHz 1.0 dB (C),
1.5 MHz +0/−5.0 dB (C)
Component (DSR-1600P):
25 Hz to 5.0 MHz 1.0 dB (Y),
5.5 MHz +1.0/−2.0 dB (Y),
5.75 MHz +1.0/−3.0 dB (Y) (TM),
25 Hz to 1.5 MHz 1.0 dB (C),
2.0 MHz +1.0/−2.0 dB (C)
Composite output (Y):
BNC type (×2, active-through), Serial
Digital Interface format (270 Mbps),
SMPTE 259M/CCIR656-III
i.DV IN/OUT (with optional DSBK-1803 i.LINK/DV
Input/Output Board installed)
S/N
6-pin IEEE 1394 connector
53 dB or more
S-video output (Y): 55 dB or more
Component output (Y): 55 dB or more
30 ns or less
Analog video outputs
REF. VIDEO OUT
Y/C delay
K-factor
BNC type ×1
Black burst
2.0% or less (K2T, KPB)
0.286 V (DSR-1600) or 0.3 V (DSR-
1600P), 75 Ω, negative sync
Composite sync
Processor adjustment range
Video level
Chrome level
Setup/Black level
3 dB/−∞ to 3 dB selectable
3 dB/−∞ to 3 dB selectable
VIDEO OUT 1, 2 (SUPER)
BNC type (×2), composite, 1.0 Vp-p,
75 Ω, sync negative
COMPONENT VIDEO OUT
BNC type (×3), Y/R−Y/B−Y
Y: 1.0 Vp-p, 75 Ω, sync negative
R−Y: 0.7 Vp-p, 75 Ω (75% color bars
for DSR-1600 or 100% color bars for
DSR-1600P)
30 IRE ( 210 mV)
Chroma phase
Y/C delay
30°
100 ns
System phase Sync: 1 µs*
SC: 180°
* +2 µs to -3 µs when using a TBC remote control unit
B−Y: 0.7 Vp-p 75 Ω (75% color bars
for DSR-1600 or 100% color bars for
DSR-1600P)
Audio performance
Frequency response
S VIDEO OUT DIN 4-pin
Y: 1.0 Vp-p, 75 Ω, sync negative
C: 0.286 Vp-p (DSR-1600) or
0.3 Vp-p (DSR-1600P), 75 Ω (burst
level)
Two-channel (48 kHz) mode:
20 Hz to 20 kHz +0.5 dB/−1.0 dB
Four-channel (32 kHz) mode:
20 Hz to 14.5 kHz +0.5 dB/−1.0 dB
Dynamic range More than 90 dB
Distortion (THD + N)
Less than 0.05% (48 kHz)
Specifications
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog audio outputs
Optional accessories
AUDIO OUT XLR 3-pin, male (× 4), +4/0/−3*/−6
dBm, 600 Ω loading, low impedance,
balanced
AUDIO MONITOR OUT
Phono jack, −11 dBu 1 dBu, 47 kΩ,
unbalanced
DSBK-1601 SDI/AES/EBU Output Board
DSBK-1602 SDTI (QSDI) Output Board
DSBK-1803 i.LINK/DV Input/Output Board
RCC-5G/10G/30G 9-pin remote control cable (length: 5 m
(16 ft)/10 m (33 ft)/30 m (98 ft))
RMM-130 Rack Mount Kit
Digital video cassette
* Selectable on DSR-1600P only
Standard size: PDVM-64ME/94ME/
124ME/184ME
Digital audio outputs
DIGITAL AUDIO (AES/EBU) OUT (with optional
DSBK-1601 SDI/AES/EBU Output Board installed)
BNC type (×2), complying with AES-
3id-1995
Mini size: PDVM-12ME/22ME/32ME/
40ME
Cleaning cassette
DV12CL (standard size), DVM12CL
(mini size)
Output for headphones
HEADPHONES
Related equipment
ES-3/7 EditStation
Stereo phone jack, −∞ to −13 dBu, 8 Ω,
unbalanced
Linear editing control unit: PVE-500, RM-450/450CE,
BVE-600/800/910/2000/9100/9100P
DME switcher: DFS-300/300P, DFS-500/500P,
DFS-700/700P
DXC-D30/D30P Color Video Camera
DSR-1/1P/300A Digital Videocassette Recorder
DSR-85/85P/2000/2000P Digital Videocassette Recorder
DSR-1800/1800P Digital Videocassette Recorder
DSR-300/300P/500WS/500WSP/130/130P/150/150P
Digital Camcorder
Time code output
TIME CODE OUT
BNC type, SMPTE time code (DSR-
1600), EBU time code (DSR-1600P),
2.2 Vp-p 3 dB, 600 Ω, unbalanced
Remote control connectors
REMOTE
D-sub 9-pin, for connection of editing
control unit*, RS-422A standard
DSRM-10 Remote Control Unit
TBC remote control unit: UVR-60/60P, BVR-50/50P
CONTROL S Stereo minijack, for connection of
SIRCS-compatible remote control unit
(DSRM-10)
VIDEO CONTROL
Design and specifications are subject to change without
notice.
D-sub 15-pin, for connection of TBC
remote control unit**
i.DV IN/OUT (with optional DSBK-1803 i.LINK/DV
Input/Output Board installed)
6-pin IEEE 1394 connector
* ES-7, PVE-500, RM-450/450CE, BVE-600/800/910/2000/9100/9100P,
etc.
**UVR-60/60P, etc.
Supplied accessories
AC power cord (1)
Operating Instructions (1)
Specifications
72
Download from Www.Somanuals.com. All Manuals Search And Download.
High-speed transfer of recordings
It is also possible to transfer the editing material itself
between the DSR-85/85P and ES-7 at four times normal
speed. In other words, the transfer can be carried out in one
fourth of the real time duration. It is of course possible to
carry out a transfer at four times normal speed when
backing up video and audio data recorded on the disk drive
to the DSR-85/85P, or in the opposite direction when
loading data backed up on the DSR-85/85P to the disk
drive. Thus the time required is much shorter than with
conventional equipment (for which, for example,
transferring a 40-minute segment of video takes 40
minutes).
ClipLink Guide
What Is ClipLink?
The ClipLink function greatly improves the efficiency of
the video production process as a whole by recording
various editing-related data on tape when shooting. As
such, ClipLink is a revolutionary function that transcends
the conventional separation of shooting and editing.
How ClipLink Changes Video Production
Techniques
The following describes various ways in which ClipLink*
video production differs from conventional video
production.
* The ClipLink system is a video production system which uses the cassette
memory function.
Recording of ClipLink log data lightens the
shooting workload
When you start shooting a scene, ClipLink log data such as
the scene number and time code data are automatically
recorded into the cassette memory. This eliminates the
need for a conventional “shot list” compiled by someone
using a stopwatch, clipboard and pencil. You can also
designate unwanted scenes as “NG” (no good) and
automatically skip all “NG” scenes when editing.
Recorded index pictures drastically cut editing
time
The ClipLink function also features index pictures as a
time-saving tool for rough editing. Each index picture is a
compressed image taken from the start of each scene,
which is recorded onto the tape as a still picture. When
editing, begin by transferring only the index pictures and
the ClipLink log data to the EditStation’s hard disk. You
can also transfer OK scenes only (“NG” scenes are
skipped).
Next, begin rough editing by viewing the index pictures on
the EditStation’s GUI display and rearranging them as you
wish. This eliminates the difficult work of matching up a
handwritten shot list with recorded scenes. After you have
completed this rough editing, you can then transfer only
the recordings needed for your video program.
ClipLink Guide
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Example System Configuration and Operation Flow
The following illustration shows an example system
configuration for using the ClipLink function and a typical
ClipLink operation flow.
Shooting
DVCAM standard cassette or DVCAM mini cassette
DVCAM camcorder
(DSR-130/130P/
300/300P/500WS/
500WSP)
Index pictures: recorded on
tape
ClipLink log data: recorded in
cassette memory
ClipLink log data recorded onto DVCAM
cassettes links shooting and editing
operations.
ClipLink log data transfer
ES-7 EditStation non-
linear editing system
a)
DSR-85/1800/1600 or
a)
DSR-85P/1800P/1600P
Digital Videocassette
Recorder/Player
Index pictures
b)
Video output (SDTI)
ClipLink log data
RS-422A interface
Editing
ES-7 EditStation non-
linear editing system
c)
a)
DSR-85 /1800/1600 or DSR-
c)
a)
85P /1800P/1600P Digital
Videocassette Recorder/Player
Actual AV data
b)
SDTI input/output
a) The DSR-1600/1600P is a videocassette player.
b) To transfer SDTI signals between the DSR-1800/1800P and ES-7 requires the optional DSBK-1802
SDTI (QSDI) Input/Output Board to be installed in the DSR-1800/1800P; to send an SDTI signal from
the DSR-1600/1600P to the ES-7 requires the optional DSBK-1602 SDTI (QSDI) Output Board to be
installed in the DSR-1600/1600P.
c) Between the DSR-85/85P and ES-7, quadruple transfer is possible through the SDTI interface.
ClipLink Guide
74
Download from Www.Somanuals.com. All Manuals Search And Download.
ClipLink log data
ClipLink log data can be recorded automatically or
manually into the cassette memory for use as a convenient
alternative to the conventional “shot list.”
Data Generated When Shooting
The following describes the kinds of data that is generated
when using the ClipLink function.
ClipLink log data includes the following items.
Index pictures
ClipLink log data Description
When shooting, a single-frame image from the Mark IN
point at the start of each scene is recorded as a still picture
into the camcorder’s internal memory. These images are
called “index pictures.” When you finish shooting, the
index pictures from all scenes are recorded onto the tape
after the last scene.
Reel number
Data (maximum length: 8 digits)
(cassette number) consisting of alphanumeric characters
and/or symbols (This is left blank at
shipping.)
Scene number
A three-digit number from 001 to 198
(starts at 001 and is automatically
incremented with each scene.)
Take number
OK/NG
This cannot be changed (set to “1” at
shipping).
Tape
Indicates the OK/NG status of a
particular scene. (In the OK case,
nothing is recorded.)
Scene 1
Scene 2
Scene 3
Scene n
Mark IN/OUT
point time codes
These are the time codes that indicate
the Mark IN and Mark OUT points for
each scene (HH:MM:SS). These time
codes are recorded when the camera
has been set to MARK mode.
DVCAM camcorder’s
internal memory
After shooting, the index
pictures in the internal
memory are recorded onto
the video tape.
The time code value is rounded up at
each Mark IN point and rounded down
at each Mark OUT point, to a whole
number of seconds.
Up to 32 index pictures can be recorded onto the tape space
normally occupied by one frame, as shown below.
Cue point time
code
This is the time code that indicates the
cue points (valid up to the frame digit).
This time code is recorded when the
camera has been set to CUE mode.
When in this mode, the time codes at
the start and end of a recording (the
Rec IN and Rec OUT time codes) are
automatically recorded as Mark IN and
OUT points, respectively.
Index picture
0
90
180
270
360
450
540
630
(PAL) NTSC
(72) 60
1
2
3
4
5
6
7
8
(144) 120
(216) 180
(288) 240
(360) 300
(432) 360
(504) 420
9
10
14
18
22
26
30
11
15
19
23
27
31
12
16
20
24
28
32
13
17
21
25
29
720 dots
Seven frame spaces are reserved at the end of the last scene
as a recording area for index pictures. (A cassette with 16
Kbits of cassette memory can record up to 198 index
pictures, and a cassette with 4 Kbits of cassette memory
can record up to 45 index pictures.)
ClipLink Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Cue point time codes
How to record ClipLink log data
This type of data is especially useful when shooting scenes
that may contain unexpected events, such as when
shooting for sports coverage or documentaries.
Set the camera to CUE mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, the current time code is recorded as a cue point
time code.
The following describes how to record the various
ClipLink log data items.
OK/NG status
To designate a scene as “NG,” press the NG button on the
camera while shooting the scene or at any time before you
begin shooting the next scene.
All scenes that do not receive an “NG” designation are
recorded as “OK” scenes.
(When you exit the VCR recording mode, changing the
OK/NG status is no longer possible.)
Start
recording
End
recording
Mark IN/OUT point time codes
Index picture 1
This data is especially useful when shooting a video
program for which a scenario has been created.
Set the camera to MARK mode before you start shooting.
While shooting, each time you press the camera’s TAKE
button, Mark IN and Mark OUT point time codes are
recorded alternately.
Rec OUT
(automatic
recording)
Cue point
Index picture 1
Index picture 2
time code
(manual
recording)
Cue point
time code
(manual
Cue point
time code
(manual
End
recording
Start
recording
Rec IN
(automatic
recording)
recording)
recording)
Mark OUT
(manual
recording)
Mark IN
(manual
recording)
Mark IN
(manual
recording)
Mark OUT
(manual
recording)
ClipLink Guide
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Time codes recorded for Mark IN/OUT points
There is a gap between actual time codes and Mark IN/
OUT time codes recorded in the cassette memory, as
shown in the figure below. The time code value is rounded
up at each Mark IN point and rounded down at each Mark
OUT point, to a whole number of seconds.
Mark IN
(or Rec IN)
Mark OUT
(or Rec OUT)
Cue
Actual time code
12:23:15:10
12:34:20:20
12:39:24:23
Rounded up
Rounded down
Time code
recorded in the
cassette memory
(The index
12:23:16
12:34:20:20
12:39:24
picture is the
image around
12:23:15:10.)
Recording capacity for Mark IN/OUT point
time codes and cue point time codes
When in MARK mode, up to 198 pairs of Mark IN and
Mark OUT points can be recorded (if using a cassette with
16 Kbits of cassette memory).
When in CUE mode, up to 396 time code points (including
all cue point time codes and all Mark (Rec) IN and Mark
(Rec) OUT point time codes) can be recorded (if using a
cassette with 16 Kbits of cassette memory).
ClipLink Guide
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
A/B roll editing
Drop frame mode
Non-drop frame mode
An editing method that uses two or
more playback VCRs to create
special effects such as dissolve and
wipe, and uses one record VCR to
record the results of the editing.
Using an editing control unit allows
efficient control of the VCRs and
very precise editing.
Time code runs at 30 frames/sec. The
NTSC system, however, runs at
about 29.97 frames/sec. Drop frame
mode adjusts this difference. The
time code and video are synchronized
by dropping the first two frames of
the time code every minute, except at
the ten-minute marks.
The number of frames of the time
code and video run is not adjusted.
When you use the time code in non-
drop frame mode, the real playback
time will be about 86 seconds shorter
per day than the time code. If you edit
frame by frame or if you determine
the length of a shot by counting the
time code, use drop frame mode.
AES/EBU format
Head drum
A unified format for digital audio
signals. It allows a single connector
to carry the signals for two channels.
A metal cylinder to which a video
head is attached. This drum is rotated
at high speeds in synchronization
with the sync signal during recording
and playback.
Non-linear editing
Editing while playing back video and
audio signals recorded on hard disks.
Video scenes stored on disk can be
cued up quickly, for increased editing
B−Y signal
A chrominance signal determined by
subtracting the Y (luminance) signal
from the B (blue) signal. One of the
component signals.
Linear editing
Editing while playing back video and
audio signals recorded on video tape.
PCM audio
This is an audio signal represented by
pulse code modulation. The analog
audio signal is first broken down into
a sequence of pulses, and these are
then represented digitally.
C (chrominance) signal
Color signal containing color
information such as hue and
saturation.
Loading
When being loaded, the tape is pulled
out of the cassette case and threaded
along the specified tape path and
wrapped round the drum to be ready
for recording or playback. Generally,
this is done automatically when you
place the cassette at the cassette
entrance of the VCR. Also called
threading.
Capstan
Preroll
A drive mechanism that moves the
tape at a specified speed. Its rotation
normally synchronizes with a
reference sync signal.
Running of a video tape to a prior to
an edit-start point to enable the tape
to reach a steady speed and to be
synchronized with other video tapes.
Component signals (YRB)
A video signal consisting of a
luminance signal (Y) and two
chrominance signals (R−Y, B−Y).
R−Y signal
Loop-through connection
A connection which allows a signal
input to an input connector to pass
through the unit and exit from an
output connector as input to external
equipment. Also called bridging
connection.
A chrominance signal determined by
subtracting the Y (luminance) signal
from the R (red) signal. One of the
component signals.
Composite signal
A composite video signal containing
video, burst and sync signals.
Reference video signal
A video signal consisting of a sync
signal or sync and burst signals, used
as a reference.
Condensation
Luminance signal
Condensation of moisture on the tape
transport mechanisms of VCRs
including the head drum. If moisture
condenses on the head drum, the tape
adheres to the drum and causes
malfunction.
The signal that determines the
brightness of the picture. Also called
Y signal. One of the component
signals.
Setup (for DSR-1600)
The difference between the reference
black level and the blanking level of
a composite signal.
SMPTE
Abbreviation of Society of Motion
Picture and Television Engineers, a
professional association established
in the USA.
Glossary
78
Download from Www.Somanuals.com. All Manuals Search And Download.
S/N
Sync signal
Abbreviation of Signal-to-Noise
(ratio). The higher the S/N value, the
less noise and higher the picture
quality.
A reference signal consisting of
vertical and horizontal sync signals
used for synchronizing the scanning
patterns of the video camera and the
monitor.
Search mode
A VCR operating mode used when
searching for specific scenes, by
viewing the video output or time code
values while playing back the tape at
various speeds in forward or reverse
direction.
TBC
Abbreviation of Time Base
Corrector. Electronic circuits to
electrically stabilize the playback
signals by removing color variation
and roll in the playback picture
caused by irregularity in drum
rotation and tape movement. Time
base correction reduces deterioration
of picture quality when transmitting
or copying playback signals.
Servo lock
Synchronizing the drum rotation
phase and tape transport phase with a
reference signal during playback and
recording so that the video heads scan
the tape in the same pattern during
playback and recording.
Threading
Standby Off mode
Time code
One of two conditions in the stop
mode. The drum does not rotate and
tape is slackened. There is no damage
to the video heads and the tape, but
the VCR is not ready for immediate
recording or playback.
Signals recorded on the tape to
supply information on tape position
such as the hour, minute, second and
frame, to assist in setting edit points
or searching for particular scenes.
Unloading
Standby On mode
When the EJECT button is pressed,
the VCR automatically winds the
tape back into the cassette case. Also
called “Unthreading.”
One of two conditions in the stop
mode. The drum is rotating and the
tape is wrapped round the drum. The
VCR is ready for recording or
playback, so a still picture can be
obtained.
User bits
Sections of time code information
consisting of a total of 32 bits that can
be used for recording information
such as date, tape ID number,
program ID number, etc.
Subcarrier
A sine wave imposed on the
luminance portion of a video signal
and modulated to carry color
information. Its amplitude represents
color saturation and its phase
represents hue.
Superimpose
To put a set of characters onto a
picture so that both can be seen at the
same time.
S-video
A signal format in which Y
(luminance) and C (chrominance)
signals are separated to reduce
interference between them so that
noiseless images are reproduced.
Glossary
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
80
Download from Www.Somanuals.com. All Manuals Search And Download.
I
Index
Numerics
A
J
Jog
D
Digital
Analog
AUDIO (AES/EBU) OUT connectors
AUDIO MONITOR OUT connector
AUDIO OUT CH-1 to CH-4
L
DSBK-
M
DVCAM
B
OPERATIONAL FUNCTION
C
E
CHANNEL CONDITION indicators
F
COMPONENT VIDEO OUT Y/R-Y/
Connections
H
O
Index
81
Download from Www.Somanuals.com. All Manuals Search And Download.
P
T
Tape transport control
Time data
R
REMOTE
U
V
Video
S
VIDEO OUT 1 and 2 (SUPER)
W
Index
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|