Sony Car Stereo System hcd sd1 User Manual

HCD-SD1

SERVICE MANUAL

AEP Model

UK Model

E Model

HCD-SD1 is the amplifier, CD and

tuner section in CMT-SD1.

Model Name Using Similar Mechanism

HCD-MD313

CDM13B-5BD19

BU-5BD19

Mechanism Type

Base Unit Type

SECTION

Optical Pick-up Type

KSS-213B/K-N

SPECIFICATIONS

— Continued on next page —

COMPACT DISC RECEIVER

MICROFILM

– 1 –

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

NOTES ON HANDLINGTHE OPTICAL PICK-UP BLOCK

OR BASE UNIT

1. SERVICING NOTE .......................................................... 4

2. GENERAL .......................................................................... 7

The laser diode in the optical pick-up block may suffer electrostatic

break-down because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also

use the procedure in the printed matter which is included in the

repair parts.

3. DISASSEMBLY

3-1. Loading Panel ....................................................................... 8

3-2. Glass ASSY........................................................................... 8

3-3. Front Panel ........................................................................... 9

3-4. Main Board and Tuner Unit .................................................. 9

3-5. CD Mechanism Deck .......................................................... 10

3-6. Back Panel ......................................................................... 10

3-7. Disc Table .......................................................................... 11

3-8. Optical Pick-up ................................................................... 11

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-

up block. Therefore, when checking the laser diode emission, ob-

serve from more than 30 cm away from the objective lens.

4. SERVICE MODE ............................................................. 12

5.TEST MODE ..................................................................... 13

6. ELECTRICAL ADJUSTMENTS ............................... 14

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK

Carry out the “S curve check” in “CD section adjustment” and check

that the S curve waveform is output two times.

7. DIAGRAMS

7-1. Circuit Boards Location ...................................................... 16

7-2. Block Diagrams

• BD Section ....................................................................... 17

• Main Section .................................................................... 19

7-3. Schematic Diagram – BD Section – ................................... 23

7-4. Printed Wiring Board – BD Section –................................. 25

7-5. Schematic Diagram – Main (1/2) Section –........................ 27

7-6. Schematic Diagram – Main (2/2) Section – ........................ 29

7-7. Printed Wiring Board – Main Section – .............................. 31

7-8. Schematic Diagram – Sub Trans Section – ......................... 33

7-9. Printed Wiring Board – Sub Trans Section – ...................... 34

7-10. Schematic Diagram – Panel Section – ............................. 35

7-11. Printed Wiring Board – Panel Section – ........................... 37

7-12. Schematic Diagram – AMP Section – .............................. 39

7-13. Printed Wiring Board – AMP Section – ........................... 41

7-14. Schematic Diagram – Connector Section –...................... 43

7-15. Printed Wiring Board – Connector Section – ................... 45

7-16. Schematic Diagram – REG Section – .............................. 47

7-17. Printed Wiring Board – REG Section –............................ 49

7-18. IC Block Diagrams ........................................................... 51

7-19. IC Pin Functions ............................................................... 54

8. EXPLODED VIEWS

8-1. Front Panel Section ............................................................. 56

8-2. Chassis Section ................................................................... 57

8-3. Mechanism Deck Section (CDM13B-5BD19) ................... 58

8-4. Base Unit Section (BU-5BD19).......................................... 59

9. ELECTRICAL PARTS LIST ........................................ 60

– 3 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 1

SERVICING NOTE

OPENING THE DISC TRAY WHEN POWER IS OFF

1 Using a thin screwdriver, rotate the internal cam

2 Open the glass door, and pull out the loading panel.

in the arrow direction completely.

ATTACHING THE GLASS ASSEMBLY

• Attach according to steps 1 to 4.

2 Pull up the glass door,

in the arrow direction.

4 Screw (PTP 2.6x6)

3 Bracket (shaft)

(Bottom side)

When securing this part, position at the

center to allow some play. Open and close

the glass window several times, and check

that the parts do not touch each other.

– 4 –

Download from Www.Somanuals.com. All Manuals Search And Download.

POSITIONS FOR SERVICING THE CONNECTOR

BOARD, SUB-TRANS BOARD, CHEMI-CON BOARD,

AND AMP BOARD

1 Remove the four screws securing the upper cover, and remove

the upper cover.

2 Remove the loading panel. (Refer to SECTION 3 DISASSEM-

BLY.)

3 Remove the four screws Asecuring the MAIN board, five screws

B securing the rear panel, two flat cables (CN701, CN702),

and open the MAIN board as shown in the figure.

4 Remove the two screws C securing the heat sink, and remove

the AMP board and CHEMI-CON board.

5 Remove the two screws D securing the SUB-TRANS board

and four screws E securing the CONNECTOR board, and re-

move the SUB-TRANS board and CONNECTOR board.

6 Return the MAIN board to its original position.

7 Insulate these boards and the MAIN board with paper, etc., and

assemble the CONNECTOR board, SUB-TRANS board,

CHEMI-CON board, and AMP board on these boards.

AMP board

CHEMI-CON board

Heat sink

SUB-TRANS board

CONNECTOR board

MAIN board

Flat type wire (CN701)

Flat type wire (CN702)

Should be insulatable

with paper, etc.

– 5 –

Download from Www.Somanuals.com. All Manuals Search And Download.

POSITION FOR SERVICING THE CD MECHANISM

DECK

1 Remove the four screws securing the upper cover, and remove

the upper cover.

2 Remove the loading panel. (Refer to SECTION 3 DISASSEM-

BLY.)

3 Remove the four screws Asecuring the MAIN board, five screws

B of the rear panel, and flat cables (CN701, CN702), and re-

move the MAIN board.

4 Remove the two screws D securing the SUB-TRANS board,

and remove the SUB-TRANS board.

5 Remove the two screws F securing the REG board.

6 Remove the three screws G securing the CDM cover, and re-

move the CDM cover.

SUB-TRANS board

7 Remove the two screws H securing the CDM, move the CDM

backwards by about 5 mm horizontally, and then lift upwards.

8 Rotate the CDM in the counterclockwise direction by about 30˚

to remove.

9 Return the MAIN and SUB-TRANS boards to their original

positions.

MAIN board

Flat type wire (CN701)

CDM cover

Flat type wire (CN702)

– 6 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 2

GENERAL

Front Panel

11 10

Location of Parts and Controls

11 DISPLAY button

12 PHONES jack

13 t indicator

14 u indicator

≠/0/TUNING – button

π button

ﬂ button

1/u (Power) button

CD disc tray

§ button

VOLUME dial

±/)/TUNING + button

TUNER/BAND button

15 Display window

10 FUNCTION button

This section is extracted from

instruction manual.

– 7 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 3

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

3-1. LOADING PANEL

1 Turn ON the power, and press the EJECT button to open the

tray.

2 Remove the loading panel in the arrow direction.

3 Press the EJECT button to close the tray.

• If the power cannot be turned ON, refer to “Opening the Disc

Tray When the Power is OFF” of “Service Note”, and open the

tray.

Loading panel

Power button

Eject button

3-2. GLASS ASSY

1 Screw (PTP2.6x6)

2 Bracket (shaft)

(Bottom side)

– 8 –

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3. FRONT PANEL

4 Flat type wire (11core)

(CN702)

6 Front panel

2 Three claws

5 Flat type wire (13core)

(CN701)

1 Three screws

(BVTP3x8)

3-4. MAIN BOARD AND TUNER UNIT

1 Four screws

(BVTP3x8)

7 MAIN board and Tuner unit

6 Flat type wire

(19core) (CN705)

8 Connector (CN706)

5 Connector (CN351)

2 Six screws

(BVTP3x8)

4 Flat type wire (19core)

(CN301)

– 9 –

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5. CD MECHANISM DECK

6 Three screws

(BVTP3x8)

7 Dust cover

9 CD mechanism deck

3 Connector

8 Two screws

(BVTP3x8)

(CN942)

5 REG board

1 Two screws

(BVTP3x8)

2 Connector

(CN945)

4 Connector

(CN994)

3-6. BACK PANEL

2 Four screws

7 Back panel

(BVTT3X8)

5 Connector

(CN901)

1 Six screws

(BVTP3X8)

3 Connector

(CN992)

6 Connector

(CN551)

8 PC board block

4 Connector

(CN991)

_{Download from Www.Som}–_anu1_a0_ls.c–_{om. All Manuals Search And Download.}

3-7. DISC TABLE

3 Holder (MG) assembly

1 Screw (BV3x8)

2 Screw (BV3x8)

4 Pull out the disc table.

3-8. OPTICAL PICK-UP

4 Remove the optical pickup in the arrow direction C.

3 Flat type wire (16 core)

(CNU101)

1 Move the claw

in the arrow A direction.

2 Remove the sled shaft in the

arrow direction B.

BD board

– 11 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 4

SERVICE MODE

Key Check Mode for Complete Lighting of LED/Fluorescent Display Tube

• Perform this mode to analyze and check malfunctions such as display defects and when buttons do not work.

Procedure:

1. Press the 1/u button to turn on the power.

2. Press the DISPLAY button and ^ button together.

3. All LEDs and the fluorescent display tube will light up completely.

4. Pressing the FUNCTION button here will light the fluorescent display tube in the following order; Partial lighting 1 n Partial lighting

2 n Complete lighting n Partial lighting 1······

Turning the VOLUME dial will switch the lighting order of the LED.

To end without shifting to the key check mode, press the 1/u button to end.

5. Pressing the p button sets the key check mode.

6. During the key check mode, “KEY=0 JOG=0” will be displayed on the fluorescent display tube.

Pressing a button will increase the value of “KEY=”. However the value will not increase for buttons which have already been pressed

once.

Rotating the VOLUME knob in the clockwise direction increases the value of “JOG=” in the order of 1, 2, 3.... and rotating in the

counterclockwise direction decreases in order of 10, 9, and 8.

7. To end the check mode, press all buttons (8 buttons). “KEY-OK” will be displayed.

Then press any button, and disconnect the power cord from the outlet.

Checking the Sub-Clock

• Perform this mode to check clock operations.

Procedure:

1. Connect an oscilloscope and frequency counter between the pin (TP791) and ground of IC701 of the MAIN board.

2. Press the § and 1/u buttons together to display “91P = 32.768k” on the fluorescent display tube.

3. Check that the signal on the oscilloscope becomes a 32 kHz rectangular waveform and the reading of the frequency counter becomes

32.768 kHz.

4. Press the 1/u button to end.

Sled Servo Mode

• In this mode, the CD sled motor can be operated freely.

Execute it when cleaning the pick-up.

Round holes can be seen on the topmost board when the case is opened. Move the pick-up and clean off the dirt in these round holes using

a cotton swab.

Procedure:

1. Press the DISPLAY and § buttons with the power of the unit OFF.

2. When the sled servo is set, “MANUAL” is displayed on the fluorescent display tube.

3. Pressing the +/TUNING/) button when the CD is in the stop state moves the pick-up to the outer track. Pressing the =/

TUNING/0 button moves it to the inner track.

4. To end this mode, perform the following steps.

1) Move the If not, the disc cannot be removed.

2) Press the DISPLAY and § buttons together.

Note:

• When ending this mode, be sure to move the pick-up to the innermost circumference. If not, the disc cannot be removed.

• Do not move the sled motor more than required as this will damage the gears.

Round holes for cleaning

Initializing (Forced Reset)

• Perform this mode when resetting the unit or when returning the unit to the customer.

• The preset frequency of the tuner, etc. will be the settings at shipment.

Procedure:

While pressing the 1/u button, insert the power cord into the outlet.

_{Download from Www.Som}–_anu1_a2_ls.c–_{om. All Manuals Search And Download.}

SECTION 5

TEST MODE

AGING MODE

This unit is equipped with an aging mode.

Use this mode for analyzing defects and for checks after completing repairs.

After repairs, perform aging 100 times and check that the unit is normal.

The aging mode is executed in the following sequence.

The aging mode will continue as long as the unit is normal.

If the unit becomes abnormal, it will display the state and number of cycles, and operations will stop. (Refer to Table 1.)

Sequence of Aging Mode:

Start

Sets the CD function and reads the CD TOC.

CD TOC OK?

Message 1

YES

Pauses first song.

OK?

YES

Message 2

Message 3

Message 4

Last song search paused state

OK?

YES

Starts last song playback

OK?

YES

End playback?

YES

Is CD playing?

Message 4

Opens the CD tray

OK?

Message 5

YES

Closes the CD tray

OK?

Message 6

YES

Power OFF

Display of number of aging cycles

Power ON

Procedure:

1. Press the DISPLAY button and =/TUNING/0 button together.

2. To end aging, press the u button and end.

Table-1 Messages and Main Reasons for Stop of Aging

Error Messages

CD No Disc NG

Details of Error

Cannot read CD TOC.

Main Causes

Optical defect, spindle defect (including motor), cannot read

Q data, disc defect (scratches, etc.), bad focus, bad GFS, etc.

Disc defect (scratches, etc.), cannot read Q data, etc.

CD Pause NG

CD Search NG

CD Play NG

Cannot set CD pause in

CD synchro mode.

Cannot search last track on CD. Optical defect, sled, tracking defect (including motor), cannot

read Q data, disc defect (scratches, etc.).

Cannot play last track on CD.

Optical defect, cannot read Q data, disc defect (scratches, etc.),

etc.

CD Open NG

CD Close NG

Cannot open CD tray.

Cannot close CD tray.

LOAD OUT SW defect

LOAD IN SW defect

– 13 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 6

ELECTRICAL ADJUSTMENTS

S Curve Check

CD SECTION

Note:

oscilloscope

BD (CD) board

1. CD Block is basically designed to operate without adjustment.

Therefore, check each item in order given.

–

TP (FEO)

TP (VC)

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10MΩ impedance.

4. Clean the object lens by an applicator with lens cleaning liquid

when the signal level is low than specified value with the fol-

lowing checks.

Procedure :

1. Connect oscilloscope to test point TP (FEO).

2. Connect between test point TP (FOK) and Ground by lead wire.

3. Turn Power switch on.

5. Adjust the focus bias adjustment when optical block is replaced.

Focus Bias Adjustment

Perform this adjustment when the optical pick-up has been replaced

or repaired.

4. Put disc (YEDS-18) in and turned Power switch on again and

actuate the focus search. (actuate the focus search when disc

table is moving in and out.)

5. Check the oscilloscope waveform (S-curve) is symmetrical be-

tween A and B. And confirm peak to peak level within 2.4 ± 0.7

Vp-p.

oscilloscope

BD (CD) board

–

TP (RF)

TP (VC)

S-curve waveform

symmetry

Procedure:

1. Connect oscilloscope to test point TP (RF).

2. Turned Power switch on.

within 2.4 ± 0.7 Vp-p

3. Put disc (YEDS-18) in and playback.

4. Adjust RV101 so that the waveform is clear.

(Clear RF signal waveform means that the shape “◊” can be

clearly distinguished at the center of the waveform.)

5. After adjustment, check the RF signal level.

6. After check, remove the lead wire connected in step 2.

Note: • Try to measure several times to make sure than the ratio of

A : B or B : A is more than 10 : 7.

• RF signal

VOLT/DIV: 200 mV

TIME/DIV: 500 nS

• Take sweep time as long as possible and light up the bright-

ness to obtain best waveform.

RF Level Check

oscilloscope

BD (CD) board

level : 1.3 ± 0.3 Vp-p

–

TP (RF)

TP (VC)

Procedure :

1. Connect oscilloscope to test point TP (RF) on BD board.

2. Turned Power switch on.

3. Put disc (YEDS-18) in and playback.

4. Confirm that oscilloscope waveform is clear and check RF sig-

nal level is correct or not.

Note: Clear RF signal waveform means that the shape “◊” can be

clearly distinguished at the center of the waveform.

• RF signal

VOLT/DIV: 200 mV

TIME/DIV: 500 nS

level : 1.3 ± 0.3 Vp-p

_{Download from Www.Som}–_anu1_a4_ls.c–_{om. All Manuals Search And Download.}

E-F Balance (1 Track Jump) Check

(Without remote commander)

Adjustment Location:

[BD (CD) BOARD] — Component Side —

oscilloscope

BD (CD) board

FOK

(Focus Bias Adjust)

RV101

TP (TEO)

TP (VC)

–

IC101

TEI

IC102

RV103

Procedure :

FEO

1. Connect oscilloscpe to test point TP (TEO) on BD board.

2. Turn Power switch on.

3. Put disc (YEDS-18) in to play the number five track.

4. Press the “P (Pause)” button. (Becomes the 1 track jump mode)

5. Confirm that the oscilloscope waveform is symmetrical on the

top and bottom in relation to 0Vdc, and check this level.

FEI

TEO

RV102

1 track jump waveform

IC104

PCK

GND

LEVEL : 300 ± 100 mVp-p

A – B

2 (A + B)

Specified level: •

x 100 = less than ± 7%

• A + B = 300 ± 100 mVp-p

Focus/Tracking Gain Adjustment (RV102, RV103)

This gain has a margin, so even if it is slightly off.

There is no problem.

Therfore, do not perform this adjustment.

Please note that it should be fixed to mechanical center position

when you moved and do not know original position.

– 15 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 7

DIAGRAMS

7-1. CIRCUIT BOARDS LOCATION

TRANS board

MAIN board

PANEL-SW board

SUB-TRANS board

BD board

LOADING board

AMP board

REG board

CHEMI-CON board

PANEL board

HP board

CONNECTOR board

VOLUME board

_{Download from Www.Som}–_anu1_a6_ls.c–_{om. All Manuals Search And Download.}

HCD-SD1

7-2. BLOCK DIAGRAMS

– BD SECTION –

OPTICAL PICK-UP

X101

22.5792 MHz

(KSS-213B)

TRACKING/FOCUS SERVO,

RF AMP

B+

5 • 6

DETECTOR

DIGITAL FILTER

D/A CONVERTER

IC104

IC101 (1/2)

MAIN

35 PD1

14 RF

DATA

LRCK

BCLK

RFO

RFI

PCMD

LRCK

BCLK

LOUT

ROUT

CD LOUT

SECTION

PD2

DIGITAL SIGNAL PROCESSOR

IC103

(Page 19)

38 F

55 CNIN

54 SEIN

C.OUT

SENS

RV102

RV101

FOCUS

GAIN

FOCUS

BIAS

56 57 59

63 51 52 53

43 46 47 49

26 28 27

+5V

FEI

FE BIAS

FEO

TEO

FE-O

FE-M

TA-M

TAO

TEI

MAIN

SECTION

S101

(LIMIT)

D OUT

RV103

TRACKING

GAIN

DATA

XLT

CLK

(Page 19)

CLK

DATA

XRST

SCOR

SENS

LD DRIVE

Q101, 102

FOK

FGD

FOCUS SW

Q103

LASER

DIODE

PHD

MAIN

XRST

SECTION

SQCK

SQSO

DF LAT

XLAT

(Page 19)

FOCUS SW

FOCUS

COIL

TRACKING

COIL

XRST

T+

T–

TRACKING

COIL DRIVE

MOTOR

DRIVER

IC351

TRACKING/FOCUS

COIL DRIVE

IC102 (1/2)

2-AXIS

DEVICE

F–

F+

DRIVE

LOAD-OUT

LOAD-IN

FOCUS

COIL DRIVE

M904 (CD)

MOTOR

SLED/SPINDLE

MOTOR DRIVE

IC102 (2/2)

SLED

SERVO

IC101 (2/2)

•

SLED MOTOR

DRIVE

M102

SLO

SL+

SLED MOTOR

OUT-SW

IN-SW

S291

(LOAD OUT)

M101

SPINDLE

MOTOR

•

SPINDLE MOTOR

DRIVE

S292

(LOAD IN)

• SIGNAL PATH

: CD

: Digital out

– 18 –

– 17 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

– MAIN SECTION –

SOUND PROCESSOR

IC101(1/2)

TUNER

UNIT

ANTENNA

SOUND PROCESSOR

IC101(2/2)

POWER AMP

IC801

SPEAKER RELAY

RY501

TUNER

BS/CS

L-OUT

TMB11

R-OUT

R-CH

–

DBFB

AMP

BASS/

TREBLE

AMP

STEREO

R-CH

MUTE

Q141

R-CH

DEFB SW

Q121

SPEAKER

INPEDANCE

6-16Ω

–

TUN

MUT

75Ω

TUNED

MUTING

• VOLUME

R-CH

RELAY SW

Q502,503

R-CH

MUTE

Q505

+8dB AMP

IC103

R-CH

J101(2/2)

RELAY DRIVE

Q504

FAN-DRIVE

Q551–553

R-CH

FM-DET-OUT

D881

LAT

DAT

CLK

OUT

BUFFER

Q450

LATCH

DATA

CLOCK

FAN

MUTE

Q111

J101

(1/2)

R-CH

RELAY SW

Q501

J102(2/2)

R-CH

J667

R-CH

TAPE

OUT

PHONES

MUTE

Q112

SWITCH

IC102

J102

(1/2)

MASTER CONTROL

IC701

CN781

MUTE SW

TC-MUT

DAT

HLP

Q183

CS/BS

TAPE

R-CH

MUTE SW

Q182

SIRCS

IC602

MD-MUT

SYSTEM

CONTROL

SIRCS

65 SDATA

SCLOCK

DAT

CLK

LAT

CLK

MUTE SW

Q181

67 SLAT1

MUTE2 69

R-CH

SP RELAY SW

MUTE1

IC311

SWITCH

Q753

STEREO

TUNED

ST.IDATA

ST.ODATA

ST.CLOCK

10 11

DIGITAL

OPTICAL

TUN

DOUT

HPSW

ON/XSRBY

FLDISP SW

SWITCH

Q103

T991

MAIN

TRANSFORMAER

HLP

SWITCH

Q793

87 ST.LATCH

HELP

MUT

ST.MUTE

DAT

CLK

SWITCH

Q792

SY LY

I C.DAT

AC IN

SWITCH

Q791

100

V/T

SX LX

I C.CLOCK

RECT

D971

±B

I C BUS

RY901

STANDBY RELAY

EXTENDER

IC791

A±7.5VREG

RECT

D941-944

RDS DECODER

IC451

A±7.5VREG

Q941, 946

S621-625,631-634

FL.RST

FL.LAT

36 FL.SLK

35 FL.DAT

AC OUTLET

CN904

KEY2 26

KEY1 25

RECTIFIER

D921,922

KEY BOARD

SWITCH

INT 16

D±5V

D+5VREG

IC921

DATA

RDS.CLK

M+7VREG

IC922

M+7V

X601

4.3 MHz

RDS.DAT

ENCODERB

ENCODERA

CDD+5V SW

Q942

CDD+5V

FLUORESCENT INDICATOR TUBE

FL601

XT1

LOUT

X702

32KHz

VOLUME

S691

XT2

VF1

VF0

X2 11

SCOR

SQSO

SQCK

X701

SCOR

43 SQSI

45 SQCK

FSW

SENS

57 CD-CLK

58 CD-DATA

59 DF-LAT

ST 12V OUT

Q951,952

RECTIFIER

Q951,953

T991

SUB

TRANSFORMER

TIMER:RED

ST12V

5MHz

TIMER LED 73

D605

5 – 50

FOCUS SW

SENS

ON:GREEN

(Page 18)

STBY+5.6V REG

IC901

RECT

D901-904

ON LED

STBY LED

STANDBY:RED

D606

STBY+5.6V

VFL

–VG

BUFFER

Q601

CLK

DAT

DF-LAT

XLAT

XRST

CD SECTION

VG SW UG REG

Q964

RECT

D961-964

63 62 61 60

Q961

D601

)/±

D604

ﬂ

D602

0/≠

D603

D601-604

RESET

VG SWITCH

Q966

SWITCH

Q752

LIGHT 64

DSP-LAT

63 BD.RESET

VF1

VF0

AC CUT

RESET

IN SW

DISPLAY DRIVER

IC601

IN SW

VF SW

Q962,963

RESET

Q751

OUT SW

LOAD IN

LOAD OUT

STBY+5.6V

D751

OUT SW

IC951

D752

61 LOAD IN

VF SWITCH

Q965

• R ch is same as L ch

• SIGNAL PATH

PANEL SW

BD POWER

TO IC701 VDD

LOAD OUT

PANEL SW

S699

SWITCH

Q943

: FM

:BS/CS

C759 BACK UP

D OUT

: PB

: REC

: CD

: Digital out

: TAPE

– 19 –

– 20 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

WAVEFORMS

– BD SECTION –

THIS NOTE IS COMMON FOR PRINTED WIRING

BOARDS AND SCHEMATIC DIAGRAMS.

(In addition to this, the necessary note is printed

in each block.)

– MAIN SECTION –

1.3 ± 0.3 Vp-p

4.3 Vp-p

For schematic diagrams.

Note:

5 MHz

IC101 #¡ (RFO) (PLAY Mode)

500 mV/DIV, 500 ns/DIV

• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolytics

IC701 !¡ (XI)

and tantalums.

• All resistors are in Ω and / W or less unless otherwise

specified.

Approx.

100 mVp-p

2.6 Vp-p

•

: internal component.

• 2 : nonflammable resistor.

• 1 : fusible resistor.

• C : panel designation.

32 kHz

IC101 $¢ (TEI) (PLAY Mode)

IC701 !¢ (XI)

50 mV/DIV, 1 µs/DIV

Note: The components identified by mark ! or dotted line

with mark ! are critical for safety.

Approx.

150 mVp-p

Replace only with part number specified.

•

S : B+ Line.

T : B– Line.

• H : adjustment for repair.

• Voltages and waveforms are dc with respect to ground in

IC101 2 (FEI) (PLAY Mode)

50 mV/DIV, 1 µs/DIV

service mode.

• Voltages are taken with aVOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-

tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-

tion tolerances.

2.6 Vp-p

7.6 µs

IC103 3 (MDP) (PLAY Mode)

• Circled numbers refer to waveforms.

5.1 Vp-p

Signal path.

: FM

: PB (MD)

: PB (TAPE)

: REC

136 µs

IC103 @• (RFCK)

: CD

• Abbreviation

: digital out

5.3 Vp-p

: Singapore model.

: Hong Kong model.

14 ns

IC103 @∞ (XPCK)

For printed wiring boards.

Note:

• X : parts extracted from the component side

5 Vp-p

•

: parts mounted on the conductor side.

: Through hole.

: internal component.

474 ns

IC103 @™ (BCLK)

• b : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

5.1 Vp-p

Caution:

Pattern face side: Parts on the pattern face side seen from the

(Side B)

Parts face side: Parts on the parts face side seen from the

(Side A) parts face are indicated.

pattern face are indicated.

22.8 µs

IC103 @º (LRCK)

• Indication of transistor

4.6 Vp-p

16.9344 MHz

These are omitted

BC E

IC104 6 (XTO)

B E

These are omitted

– 21 –

– 22 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-3. SCHEMATIC DIAGRAM – BD SECTION –

• See page 22 for Waveforms.

• See page 51 for IC Block Diagrams.

(Page 29)

Note on Schematic Diagram:

•

Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.

no mark : Stop

(

)

: CD (PLAY)

: Can not be measured.

– 23 –

– 24 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-4. PRINTED WIRING BOARD – BD SECTION –

• See page 16 for Circuit Boards Location.

(Page 32)

OPTICAL PICK-UP

BLOCK

KSS-213BA/S-N

• Semiconductor

Location

• Semiconductor

Location

Ref. No. Location

IC103

C-1

IC101

IC102

IC104

B-1

C-3

Q101

Q103

B-3

C-3

Q102

B-1

– 25 –

– 26 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-5. SCHEMATIC DIAGRAM – MAIN (1/2) SECTION –

• See page 22 for Waveforms.

• See page 31 for Printed Wiring Board.

(Page 39)

(Page

29)

(Page

29)

– 27 –

– 28 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-6. SCHEMATIC DIAGRAM – MAIN (2/2) SECTION –

• See page 22 for Waveforms.

• See page 31 for Printed Wiring Board.

• See page 53 for IC Block Diagrams.

• See page 54 for IC Pin Functions.

(Page 24)

(Page 43)

(Page 36)

(Page

28)

(Page

28)

(Page 35)

(Page 48)

– 29 –

– 30 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-7. PRINTED WIRING BOARD – MAIN SECTION –

• See page 16 for Circuit Boards Location.

(Page 41)

(Page 45)

(Page 26)

(Page 46)

• Semiconductor

Location

Ref. No. Location

D351

D751

D752

D753

D755

D791

D792

D793

A-6

G-5

G-6

B-5

AEP, UK

(Page 37)

IC101

IC102

IC103

IC351

IC701

IC791

IC951

C-3

D-2

A-1

A-5

C-6

B-6

G-6

OUT

Q103

Q111

Q112

Q121

Q141

Q181

Q182

Q183

Q211

Q212

Q222

Q241

Q751

Q752

Q753

Q781

Q782

Q783

Q791

Q792

Q793

D-2

B-1

C-1

D-4

C-4

D-4

B-1

C-1

B-3

B-4

G-7

B-7

C-6

F-8

B-6

C-6

OUT

JW734

AEP, UK SP, HK

JW735

R735

: MOUNT

: NO MOUNT

X601

AEP, UK

(Page 38)

(Page 50)

– 31 –

– 32 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-9. PRINTED WIRING BOARD – SUB SECTION –

• See page 16 for Circuit Boards Location.

7-8. SCHEMATIC DIAGRAM – SUB SECTION –

(Page 49)

DTC114ESA

(Page 47)

11EQS04

(Page 43)

DTA114ESA-TP

11ES2-NTA2B

11ES2-

DTA114ESA-TP

NTA2B

11ES2-

NTA2B

11ES2-NTA2B

(Page 45)

• Semiconductor Location

Ref. No. Location

D901

D902

D903

D904

D905

D906

D961

D962

D963

D964

D965

B-2

B-1

C-2

B-3

B-2

C-2

D966

C-1

C-2

IC901

Q901

Q961

Q962

Q963

Q964

Q965

Q966

B-3

C-2

B-3

C-3

C-2

– 33 –

– 34 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-10. SCHEMATIC DIAGRAM – PANEL SECTION –

(Page 30)

– 35 –

– 36 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-11. PRINTED WIRING BOARD – PANEL SECTION –

• See page 16 for Circuit Boards Location.

(Page 32)

• Semiconductor

Location

Ref. No. Location

D601

D602

D603

D604

D605

D606

C-3

C-4

C-5

B-7

AEP, UK

IC601

IC602

B-5

B-2

Q601

C-3

– 37 –

– 38 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-12. SCHEMATIC DIAGRAM – AMP SECTION –

(Page 47, 48)

(Page 43)

(Page 28)

– 39 –

– 40 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-13. PRINTED WIRING BOARD – AMP SECTION –

• See page 16 for Circuit Boards Location.

• Semiconductor

Location

Ref. No. Location

D553

D554

D971

D972

A-5

Q505

Q551

Q552

Q553

B-4

A-5

A-4

(Page 50)

(Page 31)

(Page 45)

– 41 –

– 42 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-14. SCHEMATIC DIAGRAM – CONNECTOR SECTION –

(Page 30)

(Page 29)

(Page 40)

(Page 33)

– 43 –

– 44 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-15. PRINTED WIRING BOARD – CONNECTOR SECTION –

• See page 16 for Circuit Boards Location.

(Page 31, 32)

• Semiconductor

Location

Ref. No. Location

D501

D556

D557

D881

B-3

C-3

D-2

IC311

B-5

Q501

Q502

Q503

Q504

B-2

B-3

(Page 34)

DIGITAL

OPTICAL

CD AUX

SPEAKER

INPEDANCE

AEP, UK

(Page 42)

SYSTEM

CONTROL

LOADING BOARD

S292

(LOAD IN)

S291

(LOAD OUT)

CN291

M904

(LOADING

MOTOR)

(Page 32)

(11)

1-634-461-

– 45 –

– 46 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-16. SCHEMATIC DIAGRAM – REG SECTION –

(Page 40)

(Page 29)

(Page 33)

– 47 –

– 48 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

7-17. PRINTED WIRING BOARD – REG SECTION –

• See page 16 for Circuit Boards Location.

OUTLET

MDS-SD1

ONLY

UNSWITCHED

200W MAX

NOT REPLACEABLE:

BUILT IN TRANSFORMER

(Page 32)

(Page 42)

(Page 34)

• Semiconductor

Location

Ref. No. Location

D921

D922

D941

D942

D943

D944

D945

D946

D952

A-4

B-2

B-1

IC921

IC922

B-3

Q941

Q942

Q943

Q951

Q952

B-2

C-2

A-1

B-1

– 49 –

– 50 –

Download from Www.Somanuals.com. All Manuals Search And Download.

HCD-SD1

IC102 BA6397FP

7-18. IC BLOCK DIAGRAMS

• BD section

IC101 CXA1782BQ

VCC

DRIVE

BUFFER

DRIVE

BUFFER

DRIVE

BUFFER

36 35

DRIVE

BUFFER

–

REGULATOR

LEVELS

DRIVER MUTE

APC

24 SENS

IIL

–

MIRR

RF IV AMP1

DFCT

TTL

23 C. OUT

DRIVE

BUFFER

DRIVE

BUFFER

DRIVE

BUFFER

DRIVE

BUFFER

–

22 XRST

21 DATA

20 XLT

TTL

IIL

RF IV AMP2

FE BIAS 37

• IIL DATA RESISTOR

• INPUT SHIFT RESISTOR

• ADDRESS DECODER

TTL

IIL

• OUTPUT DECODER

19 CLK

IC103 CXD2507AQ

–

TOG1-3

BAL1-3

FS1-4

TG1-2

TM1-7

PS1-4

IV AMP

64 63 62 61 60 59 58 57 56 55 54 53 52

18 VCC

–

FZC COMP

IV AMP

SERVO AUTO

EI 40

FOK

MON

MDP

MDS

LOCK

TEST

FILO

FILI

DATA

XRST

SENS

MUTE

SQCK

SEQUENCER

TE AMP

–

CPU

INTERFACE

SUB CODE

• TRACKING

PROCESSOR

DIGITAL

CLV

• ISET

17 ISET

• PHASE

COMPENSATION

HPF COMP

LPF COMP

46 SQSO

VEE 41

TEO 42

EXCK

SBSO

SCOR

VSS

–

TM6

TG1

EFM

DIGITAL

PLL

–

DEMODULATOR

16 SL

15 SL

PCO

VSS

TM5

TM4

–

AVSS

CLTV

AVDD

41 WFCK

ASYMMETRY

CORRECTOR

EMPH

DOUT

D/A

DIGITAL

OUT

• FCS PHASE

COMPENSATION

TZC COMP

INTERFACE

LPFI 43

TEI 44

14 SL

13 TA

38 C4M

TM3

TM2

DFCT

BIAS

ASYI

ASYO

ASYE

WDCK

FSTT

XTSL

FS1

ATSC 45

• WINDOW COMP

ATSC

TM1

TM7

16K

RAM

ERROR

35 XTAO

34 XTAI

–

FS2

CORRECTOR

TZC 46

TDFCT 47

MNTO

DFCT

–

FS4

VC 48

20 21 22 23 24 25 26 27 28 29 30 31 32

– 51 –

– 52 –

Download from Www.Somanuals.com. All Manuals Search And Download.

IC104 PCM1710U-R

LRCIN

DIN

ML/DSD

MC/DM2

INPUT

INTERFACE

DIGITAL

FILTER

MODE

CONTROL

BCKIN

MD/DM1

TIMING

CONTROL

CLKO

XTI

MUTE

MODE

CKSL

DGND

VDD

XTO

NOISE

SHAPER

DGND

VDD

5-LEVEL DAC

RIGHT

LEFT

VCC2R

20 VCC2L

GND2R

EXT1R

GND2L

EXT1L

LOW-PASS FILTER

RIGHT

LOW-PASS FILTER

LEFT

3-STAGE AMP

LEFT

3-STAGE AMP

RIGHT

EXT2R 12

17 EXT2L

VOUTR

VOUTL

VCC1

GND1 14

– MAIN Section –

IC351 LB1641

T.S.D

O.C.P

MOTOR

DRIVE

MOTOR

DRIVE

FWD/REV/STOP

CONTROL LOGIC

IC791 P82B715TD.118

LDA

LCL

SDA

SCL

BUFFER

– 53 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7-19. IC PIN FUNCTIONS

• IC701 System Control (µPD780018AYGF-015-3BA) (MAIN Board)

Function

CD power control pin, “H”:CD POWER ON

Pin No.

Pin Name

BD POWER

I/O

PANEL SW

–

Front cover open/close switch, “H”:Open glass door, “L”:Close glass door

Not used

3 to 7

AC.CUT

VPP

AC power connection signal, “L”:Power is disconnected

Normally connected to the ground pin

Main system clock output pin (5 MHz)

Main system clock input pin (5 MHz)

Positive power supply (+5V)

–

VDD1

XT2

–

Sub system clock output pin (32 kHz)

System reset input pin, “L”:RESET

Not used

XT1

RESET

–

16, 17

ENCODER A

ENCODER B

RDSCLK

RDSDAT

SCOR

VDD0

ADREF

KEY1

KEY0

–

Encoder input pin for jogging

RDS clock input pin (Not used)

RDS data input pin (Not used)

SCOR input pin

–

Positive power supply of port (+5V)

Reference voltage of A/D converter (+5V)

Key input pin (Analog input)

27 to 30

Not used

HP-SW

–

Headphone detection SW, “L”:No HP, “H”:HP

Not used

AVSS

–

A/D converter ground potential

Not used

FL.DAT

FL.CLK

FL.LAT

FL.RST

–

Serial data output for FL tube control IC (MSM9202-02)

Serial clock output for FL tube control IC (MSM9202-02)

Chip select output for FL tube control IC (MSM9202-02)

Reset signal output for FL tube control IC (MSM9202-02)

Not used

VSS1

–

Ground potential other than port and analog

Not used

41, 42

–

SQSI

CD sub code data input

–

Not used

SQCK

–

Clock output for reading CD sub code

Not used

46 to 48

IN-SW

OUT-SW

HELP

FSW

CD tray close completion detection input, “L”:CLOSE

CD tray open completion detection input, “L”:OPEN

Pin requesting power ON from the PC link adapter (optional), Normally “H”

Focus gain switch

SENSE

–

SENSE input pin

Not used

IIC DAT

IIC CLOCK

CD-CLK

CD-DATA

DF-LAT

DSP-LAT

I/O

System control communication data input/output pin

System control communication clock input/output pin

Serial clock for CD control

Serial data for CD control

Chip select signal for DA/DF

DSP IC and SSP IC chip select

_{Download from Www.Som}–_anu5_a4_ls.c–_{om. All Manuals Search And Download.}

Pin Name

LOAD IN

Function

Tray loading motor control signal, “L”:Loading

Tray loading motor control signal, “L”:When OPEN

IC reset signal for CD control, “L”:RESET

BLUE LED control port of front panel, “L”:LED ON

Serial data for SOUND PROCESSOR IC101 (M62428AFP)

Serial clock for SOUND PROCESSOR IC101 (M62428AFP)

Chip select for SOUND PROCESSOR IC101 (M62428AFP)

Audio mute signal, “H”:Power amplifier ICs (IC801, IC851) MUTE

Audio mute signal, “L”:Line mute (Q141, Q241) MUTE

Signal controlling LED which lights when power is OFF, “L”:LED ON

Ground potential of port

Pin No.

I/O

LOAD OUT

BD.RESET

LIGHT

–

SDATA

SCLOCK

SLAT1

MUTE1

MUTE2

STANDBY LED

VSS0

ON LED

TIMER LED

–

Signal controlling LED which lights when power is ON, “L”:LED ON

Signal controlling LED which lights in timer standby, “H”:LED ON

Not used

FL DISP SW

SP RELAY SW

–

Power ON/OFF signal for FL display, “H”:FL display ON

Speaker relay control signal, “L”:Speaker relay ON

Not used

77 to 80

ON/XSTBY

STEREO

TUNED

System power control signal, “H”:Standby relay ON

Tuner stereo signal, “L”:Stereo

Tuner selection OK signal, “L”:TUNED

Serial input data for tuner

ST IDATA

ST ODATA

ST.CLOCK

ST LATCH

ST MUTE

ST POWER

SIRCS

Serial output data for tuner

Serial clock for tuner

Chip select for tuner

Tuner mute output

Tuner power signal (Not used)

SIRCS code input signal (Remote control signal input)

32 KHz clock monitor out

PCL

32.768 kHz signal is output in the test mode (Refer to page 12.)

Not used

92, 93

–

DEST1

DEST2

–

Destination differentiation signal (Fixed at “H”)

Destination differentiation signal (Fixed at “L”)

Not used

HP MUTE

MD-MUTE

TC-MUTE

HP mute signal output

MD REC OUT control signal “L”:MD REC OUT MUTE (“L” only for MD function)

REC OUT control signal of TAPE

“L”:TAPE REC OUT MUTE (“L” only for TAPE function)

Function control signal “H”:TAPE, “L”:CS/BS

100

V/T

– 55 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 8

EXPLODED VIEWS

NOTE:

The components identified by

mark ! or dotted line with mark

! are critical for safety.

Replace only with part number

specified.

• Hardware (# mark) list and accessories and pack-

ing materials are given in the last of this parts list.

• Abbreviation

• Items marked “*” are not stocked since they are

seldom required for routine service. Some delay

should be anticipated when ordering these items.

• The mechanical parts with no reference number in

the exploded views are not supplied.

HK : Hong Kong model

: Singapore model

8-1. FRONT PANEL SECTION

not supplied

Supplied with J667

FL601

not supplied

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

X-4950-580-1 GLASS ASSY (CD)

4-212-584-01 BRACKET (SHAFT)

4-993-007-01 SCREW (M2.6X6), +P TAPPING

4-942-636-21 EMBLEM (NO.3.5), SONY

4-212-538-11 PANEL (AL-CD), FRONT

4-951-620-01 SCREW (2.6X8), +BVTP

1-769-940-11 WIRE (FLAT TYPE) (11 CORE)

* 17

* 18

1-769-972-11 WIRE (FLAT TYPE) (13 CORE)

1-671-609-11 HP BOARD

A-4419-060-A PANEL BOARD, COMPLETE

3-363-099-51 SCREW (CASE 3 TP2)

4-212-561-31 CASE

X-4950-364-1 KNOB (VOL) ASSY

4-212-542-11 RING (VOL)

* 20

X-4950-995-1 PANEL ASSY (CD), FRONT

4-212-580-11 SPRING (GLASS)

X-4950-999-1 BRACKET (R) ASSY

4-212-540-11 PANEL (AL-CD), LOADING

4-212-541-11 PANEL (CD), LOADING

4-212-545-11 PLATE (CD), ORNAMENTAL

4-212-590-11 HOLDER (FL)

* 11

* 13

1-671-610-11 VOLUME BOARD

X-4950-998-1 BRACKET (L) ASSY

1-671-617-11 PANEL-SW BOARD

* 24

FL601 1-517-805-11 INDICATOR TUBE, FLUORESCENT

_{Download from Www.Som}–_anu5_a6_ls.c–_{om. All Manuals Search And Download.}

8-2. CHASSIS SECTION

not supplied

T991

not supplied

65(UK,HK)

CN904

not

supplied

M551

CDM13B-5BD19

not

supplied

not supplied

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

* 51

* 52

A-4419-059-A MAIN BOARD, COMPLETE (AEP,UK)

A-4419-070-A MAIN BOARD, COMPLETE (SP,HK)

A-4419-068-A REG BOARD, COMPLETE

1-790-305-11 WIRE (FLAT TYPE) (19 CORE)

1-693-408-11 TUNER

* 61

* 62

A-4419-065-A SUB-TRANS BOARD, COMPLETE

1-671-614-11 CONNECTOR BOARD

X-4950-994-1 FOOT ASSY

* 64

1-671-611-11 AMP BOARD

!65

1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK)

3-531-576-01 RIVET

3-655-653-01 BAND (TAITON), BINDING

* 55

* 56

!57

* 58

* 59

1-671-615-11 TRANS BOARD

A-4419-064-A CHEMI-CON BOARD, COMPLETE

1-575-651-91 CORD, POWER

3-703-244-00 BUSHING (2104), CORD

4-212-564-11 PANEL (CD), BACK

!CN904 1-526-794-11 OUTLET, AC

M551

1-698-997-21 FAN, D.C.

!T991

1-433-478-11 TRANSFORMER, POWER

1-773-108-11 WIRE (FLAT TYPE) (19 CORE)(100mm)

– 57 –

Download from Www.Somanuals.com. All Manuals Search And Download.

8-3. MECHANISM DECK SECTION (CDM13B-5BD19)

not supplied

211

212

207

208

205

209

206

210

214

213

219

204

218

215

203

BU-5BD19

202

215

M904

216

201

not supplied

217

Ref. No.

Part No.

1-634-461-11 LOADING BOARD

4-927-654-01 WASHER (LIMITER)

3-659-338-00 SPRING, COMPRESSION

4-929-764-01 SHAFT (TABLE GUIDE)

4-927-620-01 GEAR (P)

Description

Remark

Ref. No.

Part No.

Description

Remark

* 201

202

203

204

205

211

212

* 213

214

4-944-012-01 TABLE, DISC

A-4604-752-A HOLDER (MG) ASSY

4-917-583-21 BRACKET, YOKE

X-4941-462-1 CHASSIS (MD) ASSY

4-933-134-01 SCREW (+PTPWH M2.6X6)

215

206

207

208

209

210

4-944-006-11 BEARING

4-927-628-01 GEAR (C)

4-927-649-01 BELT

4-929-724-01 PULLEY (B)

X-4947-265-1 ARM ASSY, SWING

216

217

218

219

4-958-593-01 SPRING (BU), COMPRESSION

4-929-747-01 HOLDER (BU)

4-929-727-01 CAM (A)

4-929-729-01 CAM (B)

A-4660-307-A MOTOR (L) ASSY (LOADING)

M904

_{Download from Www.Som}–_anu5_a8_ls.c–_{om. All Manuals Search And Download.}

8-4. BASE UNIT SECTION (BU-5BD19)

255

256

259

257

M101

253

254

M102

254

258

252

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

251

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

251

* 252

253

4-951-620-01 SCREW (2.6X8), +BVTP

A-4673-402-B BD BOARD, COMPLETE

4-917-565-01 SHAFT, SLED

257

258

259

M101

4-917-567-01 GEAR (M)

4-917-564-01 GEAR (P), FLATNESS

3-713-786-51 SCREW +P 2X3

X-4917-523-4 MOTOR ASSY (SPINDLE)

254

4-951-940-01 INSULATOR (BU)

!255

8-848-379-31 OPTICAL PICK-UP KSS-213B/S-N

M102

X-4917-504-1 MOTOR ASSY (SLED)

256

1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

– 59 –

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 9

ELECTRICAL PARTS LIST

AMP

Note:

• SEMICONDUCTORS

In each case, u: µ , for example:

uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,

uPC...: µ PC..., uPD...: µ PD...

• CAPACITORS

uF : µ F

• COILS

uH : µ H

• Abbreviation

• Due to standardization, replacements in the parts list

may be different from the parts specified in the

diagrams or the components used on the set.

• -XX, -X mean standardized parts, so they may have

some difference from the original one.

• Items marked “*” are not stocked since they are

seldom required for routine service. Some delay

should be anticipated when ordering these items.

• RESISTORS

The components identified by

mark ! or dotted line with mark

! are critical for safety.

Replace only with part number

specified.

When indicating parts by reference

number, please include the board

name.

HK : Hong Kong model

All resistors are in ohms

: Singapore model

METAL: Metal-film resistor

METAL OXIDE: Metal Oxide-film resistor

F : nonflammable

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

1-671-611-11 AMP BOARD

C103

C105

C106

1-164-346-11 CERAMIC CHIP 1uF

1-163-038-91 CERAMIC CHIP 0.1uF

1-164-690-91 CERAMIC CHIP 0.0022uF 5%

16V

25V

50V

*********

< CAPACITOR >

C107

C108

C109

C110

C111

1-164-690-91 CERAMIC CHIP 0.0022uF 5%

50V

25V

C801

C803

C804

C805

C806

1-124-720-11 ELECT

1-162-215-31 CERAMIC

1-124-724-11 ELECT

1-162-215-31 CERAMIC

1-164-159-11 CERAMIC

4.7uF

47PF

47uF

47PF

0.1uF

20%

50V

1-163-021-91 CERAMIC CHIP 0.01uF

10%

1-163-989-11 CERAMIC CHIP 0.033uF 10%

1-163-038-91 CERAMIC CHIP 0.1uF

C112

C113

C114

C115

C116

1-163-038-91 CERAMIC CHIP 0.1uF

1-164-690-91 CERAMIC CHIP 0.0022uF 5%

1-164-005-11 CERAMIC CHIP 0.47uF

25V

50V

25V

C807

C808

C809

C841

C842

1-164-159-11 CERAMIC

1-163-038-91 CERAMIC

1-126-948-11 ELECT

0.1uF

100uF

50V

25V

35V

1-126-607-11 ELECT CHIP

47uF

20%

1-163-016-00 CERAMIC CHIP 0.0039uF 10%

50V

C117

C118

C119

C120

C121

1-164-005-11 CERAMIC CHIP 0.47uF

25V

16V

25V

C851

C853

C854

C855

C856

1-124-720-11 ELECT

1-162-215-31 CERAMIC

1-124-724-11 ELECT

1-162-215-31 CERAMIC

1-164-159-11 CERAMIC

4.7uF

47PF

47uF

47PF

0.1uF

20%

50V

1-107-823-11 CERAMIC CHIP 0.47uF

1-163-038-91 CERAMIC CHIP 0.1uF

1-135-201-11 TANTALUM CHIP 10uF

1-163-038-91 CERAMIC CHIP 0.1uF

10%

20%

25V

C122

C123

C124

C125

C126

1-163-021-91 CERAMIC CHIP 0.01uF

1-163-038-91 CERAMIC CHIP 0.1uF

10%

50V

25V

50V

25V

C857

1-164-159-11 CERAMIC

< IC >

0.1uF

50V

1-126-607-11 ELECT CHIP

47uF

20%

10%

1-163-021-91 CERAMIC CHIP 0.01uF

1-163-038-91 CERAMIC CHIP 0.1uF

IC801

IC851

8-759-331-41 IC LM3876TF

C127

C128

C129

C130

C131

1-164-690-91 CERAMIC CHIP 0.0022uF 5%

50V

25V

1-163-135-00 CERAMIC CHIP 560PF

1-163-038-91 CERAMIC CHIP 0.1uF

1-164-336-11 CERAMIC CHIP 0.33uF

1-163-038-91 CERAMIC CHIP 0.1uF

< RESISTOR >

R801

R802

R803

R804

R805

1-249-417-11 CARBON

1-249-437-11 CARBON

1-249-417-11 CARBON

1-249-437-11 CARBON

1-249-433-11 CARBON

47K

22K

1/4W

C132

C133

C134

C135

C136

1-163-037-11 CERAMIC CHIP 0.022uF 10%

1-163-145-00 CERAMIC CHIP 0.0015uF 5%

1-164-346-11 CERAMIC CHIP 1uF

25V

50V

16V

50V

25V

1-163-251-11 CERAMIC CHIP 100PF

1-164-005-11 CERAMIC CHIP 0.47uF

R806

R851

R852

R853

R854

1-249-389-11 CARBON

1-249-417-11 CARBON

1-249-437-11 CARBON

1-249-417-11 CARBON

1-249-437-11 CARBON

4.7

47K

1/4W

C137

C139

C140

C141

C142

1-163-021-91 CERAMIC CHIP 0.01uF

1-163-235-11 CERAMIC CHIP 22PF

1-163-038-91 CERAMIC CHIP 0.1uF

10%

50V

25V

47K

R855

R856

1-249-433-11 CARBON

1-249-389-11 CARBON

22K

4.7

1/4W

C145

C146

C147

C148

C149

1-135-201-11 TANTALUM CHIP 10uF

1-163-275-11 CERAMIC CHIP 0.001uF 5%

1-164-346-11 CERAMIC CHIP 1uF

20%

50V

16V

**************************************************************

A-4673-402-B BD BOARD, COMPLETE

******************

< CAPACITOR >

C153

C154

1-135-259-11 TANTAL. CHIP

1-163-235-11 CERAMIC CHIP 22PF

10uF

20%

6.3V

50V

C101

C102

1-126-607-11 ELECT CHIP

1-163-275-11 CERAMIC CHIP 0.001uF 5%

47uF

20%

50V

_{Download from Www.Som}–_anu6_a0_ls.c–_{om. All Manuals Search And Download.}

CHEMI-CON

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

< CONNECTOR >

R145

R146

R147

R148

1-216-097-91 RES,CHIP

1-216-049-91 RES,CHIP

100K

1/10W

CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P

CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P

< IC >

R149

R150

R151

R152

R153

1-216-049-91 RES,CHIP

1/10W

1-216-037-00 METAL CHIP

1-216-082-00 RES,CHIP

330

24K

IC101

IC102

IC103

IC104

8-752-074-34 IC CXA1782BQ

8-759-291-06 IC BA6397FP

8-752-372-94 IC CXD2507AQ

8-759-185-29 IC PCM1710U-B

R154

R156

R157

R158

1-216-065-91 RES,CHIP

1-216-085-00 METAL CHIP

1-216-069-00 METAL CHIP

1-216-001-00 METAL CHIP

4.7K

33K

6.8K

1/10W

< TRANSISTOR >

Q101

Q102

Q103

8-729-010-08 TRANSISTOR MSB710-R

8-729-424-08 TRANSISTOR UN2111

8-729-421-22 TRANSISTOR UN2211

< VARIABLE RESISTOR >

< RESISTOR >

RV101 1-223-587-11 RES, ADJ, CARBON 22K

RV102 1-223-587-11 RES, ADJ, CARBON 22K

RV103 1-223-587-11 RES, ADJ, CARBON 22K

R102

R103

R104

R105

R106

1-216-001-00 METAL CHIP

1-216-049-91 RES,CHIP

1-216-097-91 RES,CHIP

1-216-093-91 RES,CHIP

100K

68K

1/10W

< SWITCH >

S101

1-572-085-11 SWITCH, LEAF (LIMIT)

< VIBRATOR >

R107

R108

R109

R112

R113

1-216-093-91 RES,CHIP

1-216-097-91 RES,CHIP

1-216-083-00 METAL CHIP

68K

100K

27K

1/10W

X101

1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)

**************************************************************

R114

R115

R116

R117

R118

1-216-101-00 METAL CHIP

1-216-061-00 METAL CHIP

1-216-069-00 METAL CHIP

1-216-049-91 RES,CHIP

150K

3.3K

6.8K

1/10W

A-4419-064-A CHEMI-CON BOARD, COMPLETE

*************************

< CAPACITOR >

C503

C551

C553

C554

C555

1-126-948-11 ELECT

1-128-131-11 ELECT

1-126-933-11 ELECT

1-164-159-11 CERAMIC

100uF

22uF

100uF

20%

35V

50V

16V

50V

25V

R119

R120

R121

R122

R123

1-216-089-91 RES,CHIP

1-216-114-00 RES,CHIP

1-216-097-91 RES,CHIP

1-216-099-00 METAL CHIP

47K

510K

100K

120K

1/10W

0.1uF

1-163-038-91 CERAMIC CHIP 0.1uF

C556

C971

C972

C975

C976

1-126-948-11 ELECT

1-126-042-11 ELECT

1-136-165-00 FILM

100uF

3300uF

0.1uF

20%

35V

50V

R124

R125

R126

R127

R128

1-216-091-00 METAL CHIP

1-216-069-00 METAL CHIP

1-216-063-91 RES,CHIP

1-216-089-91 RES,CHIP

1-216-105-91 RES,CHIP

56K

1/10W

6.8K

3.9K

47K

0.1uF

220K

< CONNECTOR >

R129

R130

R131

R132

R133

1-216-049-91 RES,CHIP

1-216-079-00 METAL CHIP

1-216-061-00 METAL CHIP

1/10W

18K

3.3K

* CN501 1-770-729-11 CONNECTOR, BOARD TO BOARD 10P

* CN551 1-564-506-11 PLUG, CONNECTOR 3P

< DIODE >

R134

R135

R136

R137

R138

1-216-065-91 RES,CHIP

1-216-073-00 METAL CHIP

1-216-065-91 RES,CHIP

1-216-049-91 RES,CHIP

4.7K

10K

4.7K

1/10W

D553

D554

D971

D972

8-719-933-47 DIODE HZS7B2L

8-719-933-39 DIODE HZS6C1L

8-719-062-40 DIODE D4SBL20UF3

8-719-024-99 DIODE 11ES2-NTA2B

< TRANSISTOR >

R139

R140

R141

R142

R143

1-216-033-00 METAL CHIP

1-216-081-00 METAL CHIP

1-216-061-00 METAL CHIP

1-216-121-91 RES,CHIP

220

22K

3.3K

1/10W

Q505

Q551

Q552

Q553

8-729-900-53 TRANSISTOR DTC114EK

8-729-620-05 TRANSISTOR 2SC2603-EF

8-729-026-68 TRANSISTOR 2SD2525(TP)

R144

1-216-073-00 METAL CHIP

10K

1/10W

– 61 –

Download from Www.Somanuals.com. All Manuals Search And Download.

CHEMI-CON CONNECTOR HP LOADING

Ref. No.

Part No.

Description

Remark

Ref. No.

L861

Part No.

Description

Remark

< RESISTOR >

1-420-872-00 COIL, AIR-CORE

R505

R506

R551

R552

R553

1-216-097-91 RES,CHIP

1-216-085-00 METAL CHIP

1-216-049-91 RES,CHIP

1-216-097-91 RES,CHIP

1-247-887-00 CARBON

100K

33K

100K

220K

1/10W

1/4W

< TRANSISTOR >

Q501

Q502

Q503

Q504

8-729-029-66 TRANSISTOR DTC114ESA

8-729-620-05 TRANSISTOR 2SC2603-EF

R554

R821

R822

R871

R872

1-216-065-91 RES,CHIP

1-260-089-11 CARBON

4.7K

150

1/10W

1/2W

< RESISTOR >

R501

R502

R503

1-247-887-00 CARBON

1-249-389-11 CARBON

1-249-438-11 CARBON

1-219-122-91 FUSIBLE

1-249-441-11 CARBON

220K

4.7

56K

0.33

100K

1/4W

************************************************************** !R504

R556

1-671-614-11 CONNECTOR BOARD

***************

R557

R806

1-249-441-11 CARBON

1-249-389-11 CARBON

100K

4.7

1/4W

< CAPACITOR >

(AEP,UK)

1/4W

1/2W

R809

R811

R856

1-249-437-11 CARBON

1-260-076-11 CARBON

1-249-389-11 CARBON

47K

4.7

C311

C312

C501

C502

C781

1-126-933-11 ELECT

1-164-159-11 CERAMIC

1-126-933-11 ELECT

1-126-948-11 ELECT

1-164-159-11 CERAMIC

100uF

20%

16V

50V

16V

35V

50V

0.1uF

100uF

0.1uF

1/4W

20%

(AEP,UK)

R859

R861

R881

R882

R883

1-249-438-11 CARBON

1-260-076-11 CARBON

1-249-431-11 CARBON

1-249-425-11 CARBON

56K

15K

4.7K

1/4W

1/2W

1/4W

C782

C785

C811

1-164-159-11 CERAMIC

0.1uF

50V

1/4W

(AEP,UK)

C812

C813

1-164-159-11 CERAMIC

0.1uF

50V

(AEP,UK)

50V

< RELAY >

RY501 1-515-920-11 RELAY (24V)

< TERMINAL >

(AEP,UK)

C861

C862

C863

1-164-159-11 CERAMIC

0.1uF

50V

(AEP,UK)

50V

TM811 1-537-842-11 TERMINAL BOARD (SPEAKER)

(AEP,UK) **************************************************************

50V

(AEP,UK)

1-671-609-11 HP BOARD

********

< CONNECTOR >

* CN781 1-566-856-11 SOCKET, CONNECTOR 5P

< CAPACITOR >

CN811 1-766-921-11 CONNECTOR, BOARD TO BOARD 10P

* CN961 1-774-813-11 CONNECTOR, BOARD TO BOARD 7P

CN962 1-695-342-31 PIN, CONNECTOR (PC BOARD) 19P

C681

C682

C683

1-162-294-31 CERAMIC

1-164-159-11 CERAMIC

0.001uF 10%

0.1uF

50V

(AEP,UK)

50V

< DIODE >

C684

1-164-159-11 CERAMIC

< JACK >

0.1uF

D501

D556

D557

D881

8-719-911-19 DIODE 1SS119-25

J667

1-774-933-11 JACK (LARGE TYPE)(PHONES)

**************************************************************

< FERRITE BEAD >

1-634-461-11 LOADING BOARD

FB782 1-412-473-21 INDUCTOR

< IC >

0UH

*************

< CONNECTOR >

IC311

8-749-923-04 IC TOTX178 (DIGITAL OPTICAL CD AUX)

< COIL >

* CN291 1-564-498-11 PIN, CONNECTOR 5P

< SWITCH >

L311

L801

1-410-322-11 INDUCTOR

1-420-872-00 COIL, AIR-CORE

3.3uH

S291

S292

1-571-924-11 SWITCH, LEAF (LOAD OUT)

1-571-924-11 SWITCH, LEAF (LOAD IN)

**************************************************************

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

_{Download from Www.Som}–_anu6_a2_ls.c–_{om. All Manuals Search And Download.}

MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

A-4419-059-A MAIN BOARD, COMPLETE (AEP,UK)

C234

C235

C237

C241

C242

1-136-165-00 FILM

1-126-961-11 ELECT

1-126-043-11 ELECT

1-126-963-11 ELECT

0.1uF

2.2uF

0.47uF

4.7uF

20%

50V

********************

A-4419-070-A MAIN BOARD, COMPLETE (SP,HK)

********************

4-212-590-11 HOLDER (FL)

< CAPACITOR >

C243

C301

C302

C303

C304

1-163-133-00 CERAMIC CHIP 470PF

1-124-997-11 ELECT 470uF

1-163-038-91 CERAMIC CHIP 0.1uF

1-124-473-11 ELECT

1-163-038-91 CERAMIC CHIP 0.1uF

20%

50V

10V

25V

10V

25V

1000uF

20%

C100

C101

C102

C103

C104

1-216-295-91 SHORT

1-163-251-11 CERAMIC CHIP 100PF

50V

C305

C306

C351

C352

C353

1-163-251-11 CERAMIC CHIP 100PF

1-104-664-11 ELECT

1-163-031-11 CERAMIC CHIP 0.01uF

1-162-306-11 CERAMIC 0.01uF

20%

50V

16V

50V

16V

47uF

C105

C106

C107

C121

C122

1-163-251-11 CERAMIC CHIP 100PF

50V

25V

10V

50V

20%

1-164-159-11 CERAMIC

0.1uF

1-163-038-91 CERAMIC CHIP 0.1uF

C354

C401

C402

C403

1-163-031-11 CERAMIC CHIP 0.01uF

50V

16V

1-126-022-11 ELECT

1-130-475-00 MYLAR

47uF

0.0022uF 5%

20%

1-162-294-31 CERAMIC

1-162-306-11 CERAMIC

0.001uF 10%

0.01uF

20%

C123

C126

C127

C128

C129

1-126-964-11 ELECT

1-126-963-11 ELECT

1-126-964-11 ELECT

10uF

4.7uF

10uF

20%

50V

(AEP,UK)

16V

(AEP,UK)

20%

C404

1-162-306-11 CERAMIC

0.01uF

20%

C405

C451

1-163-251-11 CERAMIC CHIP 100PF

20%

50V

(AEP,UK)

16V

(AEP,UK)

50V

(AEP,UK)

50V

1-126-961-11 ELECT

1-162-306-11 CERAMIC

1-162-291-31 CERAMIC

1-126-964-11 ELECT

2.2uF

0.01uF

560PF

10uF

C130

C131

C132

C134

C135

1-136-165-00 FILM

1-126-957-11 ELECT

1-130-479-00 MYLAR

1-136-165-00 FILM

0.1uF

0.22uF

0.0047uF 5%

0.1uF

20%

50V

C452

C453

C454

20%

10%

20%

C137

C139

C141

C142

C143

1-126-961-11 ELECT

1-164-005-11 CERAMIC CHIP 0.47uF

1-126-043-11 ELECT

1-126-963-11 ELECT

1-163-133-00 CERAMIC CHIP 470PF

1-164-159-11 CERAMIC 0.1uF

1-163-038-91 CERAMIC CHIP 0.1uF

2.2uF

20%

50V

25V

50V

(AEP,UK)

0.47uF

4.7uF

20%

C455

C456

C457

1-162-306-11 CERAMIC

0.01uF

20%

16V

(AEP,UK)

50V

(AEP,UK)

50V

(AEP,UK)

50V

1-163-239-11 CERAMIC CHIP 33PF

C191

C192

C193

C194

C195

50V

25V

50V

C701

C702

1-163-102-00 CERAMIC CHIP 24PF

1-163-233-11 CERAMIC CHIP 18PF

1-163-141-00 CERAMIC CHIP 0.001uF 5%

C703

C704

C748

C751

C752

1-163-038-91 CERAMIC CHIP 0.1uF

25V

50V

16V

25V

C196

C197

C198

C199

C201

1-162-294-31 CERAMIC

1-124-995-11 ELECT

1-164-159-11 CERAMIC

1-124-995-11 ELECT

0.001uF 10%

50V

10V

50V

10V

50V

220uF

0.1uF

220uF

20%

1-164-159-11 CERAMIC

1-124-589-11 ELECT

0.1uF

47uF

20%

1-163-038-91 CERAMIC CHIP 0.1uF

1-163-251-11 CERAMIC CHIP 100PF

C753

C754

C755

C756

C757

1-126-925-11 ELECT

1-163-038-91 CERAMIC CHIP 0.1uF

1-124-589-11 ELECT

1-164-159-11 CERAMIC

470uF

20%

10V

25V

16V

50V

16V

C202

C203

C204

C205

C221

1-163-251-11 CERAMIC CHIP 100PF

20%

50V

10V

47uF

0.1uF

1-126-022-11 ELECT

47uF

C758

C759

C791

1-164-159-11 CERAMIC

1-104-905-11 CAPACITOR

1-163-038-91 CERAMIC CHIP 0.1uF

0.1uF

0.22F

50V

5.5V

25V

C222

C223

C224

C226

C227

1-130-475-00 MYLAR

1-130-471-00 MYLAR

1-104-664-11 ELECT

1-126-963-11 ELECT

0.0022uF 5%

0.001uF 5%

50V

16V

50V

47uF

4.7uF

20%

< CONNECTOR >

* CN101 1-564-506-11 PLUG, CONNECTOR 3P

CN301 1-770-067-11 CONNECTOR, FFC/FPC 19P

* CN351 1-564-339-00 PIN, CONNECTOR 5P

CN401 1-774-289-11 PIN, CONNECTOR (PC BOARD) 15P

CN701 1-784-601-11 SOCKET, CONNECTOR (NON ZIF)13P

C228

C229

C230

C231

C232

1-126-963-11 ELECT

1-126-964-11 ELECT

1-136-165-00 FILM

1-126-957-11 ELECT

1-130-479-00 MYLAR

4.7uF

10uF

0.1uF

0.22uF

0.0047uF 5%

20%

50V

20%

– 63 –

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

L405

Part No.

Description

Remark

CN702 1-785-462-11 SOCKET, CONNECTOR (NON-ZIF)11P

CN703 1-770-380-11 CONNECTOR, BOARD TO BOARD 8P

CN704 1-770-380-11 CONNECTOR, BOARD TO BOARD 8P

CN705 1-695-342-31 PIN, CONNECTOR (PC BOARD) 19P

1-410-482-31 INDUCTOR

100uH

< TRANSISTOR >

Q103

Q111

Q112

Q121

Q141

8-729-900-53 TRANSISTOR DTC114EK

8-729-107-46 TRANSISTOR 2SC3624A-L15

8-729-120-28 TRANSISTOR 2SC1623-L5L6

8-729-107-46 TRANSISTOR 2SC3624A-L15

< DIODE >

D351

D751

D752

D753

D755

8-719-921-40 DIODE MTZJ-4.7C

8-719-911-19 DIODE 1SS119-25

8-719-024-99 DIODE 11ES2-NTA2B

8-719-911-19 DIODE 1SS119-25

Q181

Q182

Q183

Q211

Q212

8-729-029-21 TRANSISTOR DTA114ESA-TP

8-729-107-46 TRANSISTOR 2SC3624A-L15

D791

D792

D793

8-719-914-42 DIODE DA204K

Q222

Q241

Q450

Q751

Q752

8-729-120-28 TRANSISTOR 2SC1623-L5L6

8-729-107-46 TRANSISTOR 2SC3624A-L15

8-729-620-05 TRANSISTOR 2SC2603-EF

8-729-600-22 TRANSISTOR 2SA1235-F

< FERRITE BEAD >

FB301 1-412-473-21 INDUCTOR

FB791 1-500-445-21 FERRITE

FB792 1-500-445-21 FERRITE

0UH

Q753

Q781

Q782

Q783

Q791

8-729-027-23 TRANSISTOR DTA114EK

8-729-107-46 TRANSISTOR 2SC3624A-L15

8-729-025-28 TRANSISTOR 2SK1828

< IC >

IC101

IC102

IC103

IC351

IC451

8-759-494-40 IC M62428AFP600C

8-759-300-71 IC HD14053BFP

8-759-100-96 IC UPC4558G2

8-759-822-09 IC LB1641

Q792

8-729-025-28 TRANSISTOR 2SK1828

< RESISTOR >

8-759-560-51 IC BU1924F (AEP,UK)

IC701

IC791

IC951

8-759-549-47 IC uPD780018AYGF-015-3BA

8-759-549-80 IC P82B715TD.118

8-759-635-63 IC M51943BSL

R101

R102

R103

R104

R105

1-216-077-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-033-00 METAL CHIP

1-216-049-91 RES,CHIP

1-216-105-91 RES,CHIP

15K

10K

220

1/10W

< JACK >

220K

J101

J102

1-766-396-11 JACK, PIN 4P (MD IN/OUT)

1-779-688-11 JACK, PIN 6P (TAPE,CS/BS IN/OUT)

R106

R107

R108

R109

R111

1-216-033-00 METAL CHIP

1-216-077-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-089-91 RES,CHIP

1-216-049-91 RES,CHIP

220

15K

10K

47K

1/10W

< JUMPER RESISTOR >

JW301 1-216-295-91 SHORT

JW302 1-216-295-91 SHORT

JW303 1-216-296-91 SHORT

JW304 1-216-296-91 SHORT

JW412 1-216-295-91 SHORT

R112

R113

R114

R115

R116

1-216-065-91 RES,CHIP

1-216-049-91 RES,CHIP

1-216-065-91 RES,CHIP

1-216-097-91 RES,CHIP

1-216-093-91 RES,CHIP

4.7K

100K

68K

1/10W

JW413 1-216-295-91 SHORT

JW701 1-216-296-91 SHORT

JW734 1-216-295-91 SHORT

JW735 1-216-295-91 SHORT

JW791 1-216-295-91 SHORT

R117

R123

R124

R125

R126

1-216-089-91 RES,CHIP

1-216-055-00 METAL CHIP

1-216-069-00 METAL CHIP

1-216-104-00 METAL CHIP

1-216-081-00 METAL CHIP

47K

1/10W

0 (SP, HK)

1.8K

6.8K

200K

22K

JW792 1-216-296-91 SHORT

JW793 1-216-296-91 SHORT

JW794 1-216-296-91 SHORT

JW795 1-216-295-91 SHORT

JW796 1-216-296-91 SHORT

R127

R128

R129

R130

R139

1-216-061-00 METAL CHIP

1-216-081-00 METAL CHIP

1-216-121-91 RES,CHIP

1-216-073-00 METAL CHIP

1-216-121-91 RES,CHIP

3.3K

22K

10K

1/10W

JW797 1-216-296-91 SHORT

JW798 1-216-296-91 SHORT

R141

R142

R143

R181

R183

1-216-057-00 METAL CHIP

1-216-065-91 RES,CHIP

1-216-089-91 RES,CHIP

1-247-887-00 CARBON

2.2K

4.7K

47K

220K

1/10W

1/4W

< COIL >

L401

L402

L403

L404

1-410-482-31 INDUCTOR

100uH

1/4W

R185

1-247-887-00 CARBON

220K

1/4W

_{Download from Www.Som}–_anu6_a4_ls.c–_{om. All Manuals Search And Download.}

MAIN PANEL

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R191

R192

R193

R201

1-249-413-11 CARBON

1-216-077-00 METAL CHIP

470

15K

1/4W

1/10W

R706

R707

R708

1-216-073-00 METAL CHIP

1-216-097-91 RES,CHIP

10K

100K

1/10W

R709

R710

R711

R712

R713

1-216-025-91 RES,CHIP

1-216-073-00 METAL CHIP

100

10K

1/10W

R202

R203

R204

R205

R206

1-216-073-00 METAL CHIP

1-216-033-00 METAL CHIP

1-216-049-91 RES,CHIP

1-216-105-91 RES,CHIP

1-216-033-00 METAL CHIP

10K

220

220K

220

1/10W

R714

R719

R720

R721

R722

1-216-073-00 METAL CHIP

1-216-049-91 RES,CHIP

1-247-807-31 CARBON

10K

100

1/10W

1/4W

R207

R208

R211

R212

R213

1-216-077-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-049-91 RES,CHIP

1-216-065-91 RES,CHIP

1-216-049-91 RES,CHIP

15K

10K

4.7K

1/10W

R723

R724

R725

R726

R727

1-247-807-31 CARBON

100

1/4W

R214

R215

R216

R217

R223

1-216-065-91 RES,CHIP

1-216-097-91 RES,CHIP

1-216-093-91 RES,CHIP

1-216-089-91 RES,CHIP

1-216-055-00 METAL CHIP

4.7K

100K

68K

47K

1.8K

1/10W

R728

R730

R731

R732

R733

1-216-025-91 RES,CHIP

1-247-807-31 CARBON

100

1/10W

1/4W

R224

R225

R227

R228

R229

1-216-069-00 METAL CHIP

1-216-104-00 METAL CHIP

1-216-061-00 METAL CHIP

1-216-081-00 METAL CHIP

1-216-121-91 RES,CHIP

6.8K

200K

3.3K

22K

1/10W

R735

1-216-097-91 RES,CHIP

100K

1/10W

(AEP,UK)

1/10W

1/4W

R230

R241

R242

R243

R351

1-216-073-00 METAL CHIP

1-249-421-11 CARBON

1-216-065-91 RES,CHIP

1-216-089-91 RES,CHIP

1-247-807-31 CARBON

10K

2.2K

4.7K

47K

100

1/10W

1/4W

1/10W

1/4W

R734

R736

R738

R739

1-216-097-91 RES,CHIP

1-247-807-31 CARBON

1-216-097-91 RES,CHIP

100K

100

100K

1/10W

R401

R402

R403

R404

R405

1-249-417-11 CARBON

1-216-025-91 RES,CHIP

100

1/4W

1/10W

R740

R741

R751

R752

R753

1-249-417-11 CARBON

1-216-073-00 METAL CHIP

1-249-417-11 CARBON

1-249-425-11 CARBON

1-249-437-11 CARBON

10K

4.7K

47K

1/4W

1/10W

1/4W

R406

R407

1-216-025-91 RES,CHIP

1-249-405-11 CARBON

100

1/10W

1/4W

(AEP,UK)

1/4W

(AEP,UK)

1/4W

R754

R755

R756

R781

R782

1-249-437-11 CARBON

1-249-429-11 CARBON

1-216-025-91 RES,CHIP

1-216-073-00 METAL CHIP

1-216-045-00 METAL CHIP

47K

10K

100

10K

680

1/4W

1/10W

R408

R409

R410

1-249-429-11 CARBON

1-249-417-11 CARBON

1-216-073-00 METAL CHIP

10K

(AEP,UK)

1/10W

R783

R791

R792

R793

R794

1-216-045-00 METAL CHIP

1-216-065-91 RES,CHIP

680

1/10W

10K

4.7K

R411

!R451

1-216-073-00 METAL CHIP

1-249-401-11 CARBON

10K

1/10W

1/4W

(AEP,UK)

1/10W

(AEP,UK)

1/10W

(AEP,UK)

R452

R453

R454

1-216-129-00 METAL CHIP

1-216-049-91 RES,CHIP

1-249-409-11 CARBON

2.2M

< VIBRATOR >

X601

X701

X702

1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz)(AEP,UK)

1-579-233-11 VIBRATOR, CERAMIC (5MHz)

1-567-098-41 VIBRATOR, CRYSTAL (32kHz)

220

1/4W

(AEP,UK)

**************************************************************

R455

1-249-409-11 CARBON

220

1/4W

(AEP,UK)

1/4W

A-4419-060-A PANEL BOARD, COMPLETE

R456

R457

R701

R702

1-249-441-11 CARBON

1-249-425-11 CARBON

1-216-109-00 METAL CHIP

100K

4.7K

*********************

1/4W

< CAPACITOR >

330K

1/10W

C601

C602

C603

1-163-141-00 CERAMIC CHIP 0.001uF 5%

50V

R704

R705

1-216-061-00 METAL CHIP

3.3K

1/10W

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

– 65 –

Download from Www.Somanuals.com. All Manuals Search And Download.

REG

PANEL PANEL-SW

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

C604

C605

1-163-141-00 CERAMIC CHIP 0.001uF 5%

50V

S622

S623

S624

S625

1-762-875-21 SWITCH, KEYBOARD (±/), TUNING +)

1-762-875-21 SWITCH, KEYBOARD (≠/0, TUNING -)

1-762-875-21 SWITCH, KEYBOARD (π)

1-162-290-31 CERAMIC

470PF

10%

C607

C608

C609

C610

C611

1-163-038-91 CERAMIC CHIP 0.1uF

25V

50V

1-762-875-21 SWITCH, KEYBOARD (ﬂ)

1-164-159-11 CERAMIC

1-162-215-31 CERAMIC

1-164-159-11 CERAMIC

0.1uF

47PF

0.1uF

S631

S632

S633

S634

1-762-875-21 SWITCH, KEYBOARD (1/u)

1-762-875-21 SWITCH, KEYBOARD (DISPLAY)

1-762-875-21 SWITCH, KEYBOARD (FUNCTION)

1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)

C612

C613

1-124-589-11 ELECT

1-128-131-11 ELECT

47uF

22uF

20%

16V

50V

**************************************************************

< CONNECTOR >

1-671-617-11 PANEL-SW BOARD

**************

* CN601 1-695-374-31 PIN, CONNECTOR (PC BOARD) 13P

CN603 1-695-372-31 PIN, CONNECTOR (PC BOARD) 11P

< SWITCH >

< DIODE >

S699

1-771-516-11 SWITCH, PUSH(DETECTION)(1 KEY)

D601

D602

D603

D604

D605

8-719-072-76 DIODE SEL5E23C-TP15 (±/))

8-719-072-76 DIODE SEL5E23C-TP15 (≠/0)

8-719-072-76 DIODE SEL5E23C-TP15 (π)

8-719-072-76 DIODE SEL5E23C-TP15 (ﬂ)

8-719-058-04 DIODE SEL5223S-TP15 (t)

**************************************************************

A-4419-068-A REG BOARD, COMPLETE

*******************

< FUSE >

D606

8-719-056-13 DIODE SML72423C-TP4 (u)

!F941

!F942

1-532-465-31 FUSE (T3.15AL/250V)

< FLUORESCENT INDICATOR >

FL601 1-517-805-11 INDICATOR TUBE, FLUORESCENT

< IC >

< CAPACITOR >

C921

C922

C923

C924

C925

1-126-767-11 ELECT

1-164-159-11 CERAMIC

1-126-964-11 ELECT

1-164-159-11 CERAMIC

1-126-964-11 ELECT

1000uF

0.1uF

10uF

0.1uF

10uF

20%

16V

50V

IC601

IC602

8-759-572-22 IC MSM9202-02GS-KR1

8-759-459-85 IC NJL63H400A

< TRANSISTOR >

8-729-900-53 TRANSISTOR DTC114EK

< RESISTOR >

C941

C942

C943

C944

C945

1-126-934-11 ELECT

1-126-933-11 ELECT

1-164-159-11 CERAMIC

1-126-933-11 ELECT

1-124-995-11 ELECT

220uF

100uF

0.1uF

100uF

220uF

20%

16V

50V

16V

10V

Q601

20%

R601

R602

R603

R604

R605

1-216-025-91 RES,CHIP

1-249-437-11 CARBON

100

47K

1/10W

1/4W

C946

C947

C948

C949

C951

1-126-934-11 ELECT

1-124-995-11 ELECT

1-164-159-11 CERAMIC

1-126-940-11 ELECT

220uF

0.1uF

330uF

20%

16V

10V

50V

25V

20%

R606

R607

R608

R609

R610

1-247-843-11 CARBON

1-216-029-00 METAL CHIP

1-249-413-11 CARBON

3.3K

150

470

1/4W

1/10W

1/4W

C952

C953

C954

1-126-967-11 ELECT

1-164-159-11 CERAMIC

1-162-306-11 CERAMIC

47uF

0.1uF

0.01uF

50V

16V

< CONNECTOR >

* CN942 1-564-522-11 PLUG, CONNECTOR 7P

CN943 1-770-405-11 CONNECTOR, BOARD TO BOARD 8P

CN944 1-770-405-11 CONNECTOR, BOARD TO BOARD 8P

CN945 1-506-481-11 PIN, CONNECTOR 2P

R611

R612

R613

R621

R622

1-249-411-11 CARBON

1-216-029-00 METAL CHIP

1-249-413-11 CARBON

1-249-415-11 CARBON

330

150

470

680

1/4W

1/10W

1/4W

R623

R624

R631

R632

R633

1-249-417-11 CARBON

1-249-419-11 CARBON

1-249-413-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1/4W

< DIODE >

1.5K

470

680

D921

D922

D941

D942

D943

8-719-210-21 DIODE 11EQS04

< SWITCH >

S621

1-762-875-21 SWITCH, KEYBOARD (§)

D944

8-719-210-21 DIODE 11EQS04

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

_{Download from Www.Som}–_anu6_a6_ls.c–_{om. All Manuals Search And Download.}

REG

SUB-TRANS

TRANS

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

D945

D946

D952

8-719-986-04 DIODE HZS9A1LTA

8-719-986-26 DIODE HZS12A3LTA

D962

D963

D964

8-719-024-99 DIODE 11ES2-NTA2B

< GROUND TERMINAL >

D965

D966

8-719-986-67 DIODE HZS33-2LTA

8-719-921-37 DIODE MTZJ-4.7

EPT941 1-537-770-21 TERMINAL BOARD, GROUND

< FUSE HOLDER >

< IC >

8-759-373-79 IC TA7805SB

< TRANSISTOR >

IC901

FH941 1-533-293-11 FUSE HOLDER

FH942 1-533-293-11 FUSE HOLDER

FH943 1-533-293-11 FUSE HOLDER

FH944 1-533-293-11 FUSE HOLDER

Q901

Q961

Q962

Q963

Q964

8-729-029-66 TRANSISTOR DTC114ESA

8-729-118-01 TRANSISTOR 2SB1116-K

8-729-040-19 TRANSISTOR RT1N137L-TP

< IC >

IC921

IC922

8-759-231-53 IC TA7805S

8-759-373-82 IC TA7807SB

Q965

Q966

8-729-029-21 TRANSISTOR DTA114ESA-TP

< TRANSISTOR >

Q941

Q942

Q943

Q951

Q952

8-729-140-96 TRANSISTOR 2SD774-34

8-729-040-20 TRANSISTOR RT1P137L-TP

8-729-029-66 TRANSISTOR DTC114ESA

8-729-202-67 TRANSISTOR 2SK246-GR3

8-729-026-68 TRANSISTOR 2SD2525(TP)

< RESISTOR >

R901

!R961

R962

R964

R965

1-249-429-11 CARBON

1-217-637-00 FUSIBLE

1-249-429-11 CARBON

1-247-807-31 CARBON

10K

100

1/4W

< RESISTOR >

R925

R941

1-249-411-11 CARBON

1-247-843-11 CARBON

330

3.3K

1/4W

R966

R967

R968

R969

1-247-807-31 CARBON

1-249-428-11 CARBON

1-249-441-11 CARBON

100

8.2K

100K

1/4W

< THERMISTOR(POSITIVE) >

THP941 1-801-671-11 THERMISTOR, POSITIVE

THP942 1-801-671-11 THERMISTOR, POSITIVE

< RELAY >

RY901 1-755-276-11 RELAY, POWER

**************************************************************

< TRANSFORMER >

A-4419-065-A SUB-TRANS BOARD, COMPLETE

*************************

!T901

1-433-476-11 TRANSFORMER, POWER

< CAPACITOR >

**************************************************************

C901

C902

C903

C904

C962

1-126-935-11 ELECT

1-126-933-11 ELECT

1-113-925-11 CERAMIC

1-164-159-11 CERAMIC

1-128-576-11 ELECT

470uF

100uF

0.01uF

0.1uF

20%

16V

250V

50V

63V

1-671-615-11 TRANS BOARD

***********

< CONNECTOR >

100uF

20%

* CN991 1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P

* CN992 1-568-226-11 PIN, CONNECTOR 2P

* CN994 1-564-522-11 PLUG, CONNECTOR 7P

C963

C964

1-164-159-11 CERAMIC

1-126-948-11 ELECT

0.1uF

100uF

50V

35V

< CONNECTOR >

< FUSE >

* CN901 1-564-687-11 PIN, CONNECTOR 3P

!F991

1-532-465-31 FUSE (T3.15AL/250V)

< DIODE >

CN902 1-779-939-11 CONNECTOR, BOARD TO BOARD 7P

< DIODE >

D951

D953

8-719-024-99 DIODE 11ES2-NTA2B

D901

D902

D903

D904

D905

8-719-210-21 DIODE 11EQS04

8-719-911-19 DIODE 1SS119-25

< FUSE HOLDER >

FH991 1-533-293-11 FUSE HOLDER

FH992 1-533-293-11 FUSE HOLDER

D906

D961

8-719-911-19 DIODE 1SS119-25

8-719-024-99 DIODE 11ES2-NTA2B

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

Download from Www.Somanuals.com. All Manuals Search And Download.

– 67 –

HCD-SD1

TRANS

VOLUME

Ref. No.

Part No.

Description

Remark

< THERMISTOR(POSITIVE) >

THP944 1-801-726-11 THERMISTOR, POSITIVE

THP945 1-801-726-11 THERMISTOR, POSITIVE

**************************************************************

1-671-610-11 VOLUME BOARD

************

< CAPACITOR >

C691

C692

1-162-306-11 CERAMIC

0.01uF

20%

16V

< CONNECTOR >

* CLP691 1-690-880-31 LEAD (WITH CONNECTOR)

< SWITCH >

S691

1-418-012-11 ENCODER, ROTARY (VOLUME)

**************************************************************

MISCELLANEOUS

*************

1-769-940-11 WIRE (FLAT TYPE) (11 CORE)

1-769-972-11 WIRE (FLAT TYPE) (13 CORE)

1-790-305-11 WIRE (FLAT TYPE) (19 CORE)

1-693-408-11 TUNER

!57

1-575-651-91 CORD, POWER

!65

!255

256

1-773-108-11 WIRE (FLAT TYPE) (19 CORE)(100mm)

1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK)

8-848-379-31 OPTICAL PICK-UP KSS-213B/S-N

1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

!CN904 1-526-794-11 OUTLET, AC

FL601 1-517-805-11 INDICATOR TUBE, FLUORESCENT

M101

M102

M551

M904

X-4917-523-4 MOTOR ASSY (SPINDLE)

X-4917-504-1 MOTOR ASSY (SLED)

1-698-997-21 FAN, D.C.

A-4660-307-A MOTOR (L) ASSY

!T991

1-433-478-11 TRANSFORMER, POWER

**************************************************************

*************

HARDWARE LIST

*************

7-685-871-01 SCREW +BVTT 3X6 (S)

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

7-684-024-04 N 4, TYPE 2

7-682-562-09 SCREW +B 4X10

7-624-105-04 STOP RING 2.3, TYPE -E

7-685-234-19 SCREW +KTP 2.6X8 TYPE2NON-SLIT

7-621-775-10 SCREW +B 2.6X4

The components identified by mark ! or dotted

line with mark ! are critical for safety.

Replace only with part number specified.

98L0953-1

Published by Quality Assurance Dept.

(Shibaura)

Sony Corporation

Home A&V Products Company

9-922-969-11

_{Download from Www.Som}–_anu6_a8_ls.c–_{om. All Manuals Search And Download.}

Singer Sewing Machine 117 3 User Manual
Snapper Lawn Mower 1690624 User Manual
Soleus Air Electric Heater 3092402 User Manual
Sony Computer Drive NW HD3 User Manual
Sony Computer Monitor SUN 17e10 SGI 17e11 PC User Manual
Sony DVR VRD MC3 User Manual
SPX Cooling Technologies Electric Heater 92 1322C User Manual
Stamina Products Stud Sensor 40 0046A User Manual
Sylvania CRT Television 6427GFG A User Manual
Tamron Satellite Radio MST2000 User Manual