3-242-100-31 (1)
2
A
AUDIO OUT
FRONT
SUB OUT (MONO)
FM/MW/LW
Compact Disc
Player
AUDIO OUT
REAR
Installation/Connections
安裝／線路連接
BUS AUDIO IN
B
BUS CONTROL IN
BUS AUDIO IN
Source selector*
音源選擇器*
XA-C30
* not supplied
非附送
BUS CONTROL IN
CDX-M730
CDX-M630
Sony Corporation © 2002 Printed in Korea
Cautions
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
1
1
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g., seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
2
3
4
TOP
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
× 4
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
8
5
6
7
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
× 2
•When no car circuits are rated high enough,
connect the unit directly to the battery.
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
Equipment used in illustrations (not supplied)
插圖中的裝置（非附送）
Parts Iist (1)
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
The numbers in the list are keyed to those in the
instructions.
Front speaker
前揚聲器
CD/MD changer
CD/MD 換碟機
For the use of release key 8, see the supplied
operating instructions.
5 To a car’s illumination signal
Be sure to connect the black ground lead to it
first.
Caution
6 To the +12 V power terminal which is energized
Handle the bracket 1 carefully to avoid injuring
your fingers.
Active subwoofer
有源超低音揚聲器
Rear speaker
後揚聲器
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
TOP
Be sure to connect the black earth lead to it
first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
Power amplifier
功率放大器
7 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to it first.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
B
5 A
(OPEN)
CDX-M630
Extended portion of the front panel
前面板的伸出部分
CDX-M730
Extended portion of the front panel
前面板的伸出部分
c
20 mm
7 mm
20 mm
7.2 mm
1
4
6
*
182 mm
with the TOP marking up
要使帶 TOP 標記面朝上
53 mm
TOP
1
Dashboard
儀表板
2
3
Fire wall
防火壁
TOP
1
4
6
4
5
2
Bend these claws outward
for a tight fit, if necessary.
5
若有必要，則可向外彎曲這些卡爪，
以便牢固安裝。
3
5
4
B NISSAN
7 A TOYOTA
4
max. size
4
max. size
5 × 8 mm
5 × 8 mm
最大尺寸
5×8 mm
最大尺寸
5×8 mm
to dashboard/centre console
至儀表板／中央控制箱
to dashboard/centre console
至儀表板／中央控制箱
4
max. size
5 × 8 mm
4
max. size
5 × 8 mm
Bracket
托架
Bracket
托架
最大尺寸
5×8 mm
最大尺寸
5×8 mm
Bracket
托架
Bracket
托架
Existing parts supplied with your car
隨汽車附送的部件
Existing parts supplied with your car
隨汽車附送的部件
CDX-M730
8
CDX-M630
Main-display position
主顯示幕位置
Main-display position
主顯示幕位置
Sub-display position
副顯示幕位置
Sub-display position
副顯示幕位置
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
Mounting the unit in a Japanese
car (7)
使用前注意事項
將本機安裝於日本產汽車上時
（7）
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•請仔細選擇安裝位置，以使本機不妨礙正常的
駕駛操作。
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
有的日本產汽車不能安裝本機，在這種情形下，
請您向當地的 Sony 經銷商諮詢。
•避免將本機安裝在多塵、髒亂、極易受震動的
地方，或者高溫之處，如陽光直射處或暖氣機
前。
註
為防止發生故障，安裝時只能使用附送的螺絲 4。
•為了安全和安裝牢固，安裝時請使用附送的安
裝部件。
Note
To prevent malfunction, install only with the
•Use only the supplied mounting hardware for
a safe and secure installation.
supplied screws 4.
安裝角度之調整
請在 60 度以內調整安裝角度。
Mounting angle adjustment
安裝在點火鑰匙開關上沒有 ACC
（輔助）位置的汽車上時的警告
Adjust the mounting angle to less than 60°.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
在關掉汽車引擎之後，一定請按下機器上的
(OFF) 兩秒以關掉時鐘顯示。
前面板的伸出部分（4）
Extended portion of the front
panel (4)
如果只短暫地按一下 (OFF)，將不會關掉時鐘顯
示而浪費電池。
如何拆卸和裝配前面板（5）
(僅限於CDX-M730)
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
How to detach and attach the
front panel (5) (CDX-M730
only)
安裝本機之前，請先拆卸前面板。
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET 按鈕（8）
5-A 拆卸
當安裝和連接完成後，必須用原子筆等按壓
RESET 按鈕。
1. 按住本機上的 (OPEN) 鍵2秒鐘。
前面板自動傾斜 30 度角。
2. 如圖所示拆下前面板。
Before installing the unit, detach the front
panel.
前面板完全拆下後，副顯示幕自動關閉。
5-B 裝配
5-A To detach
RESET button (8)
1 Press (OPEN) on the unit for 2 seconds.
The front panel automatically tilts at an angle
of 30°
2 Detach the front panel as illustrated.
After the front panel is completely detached,
the sub display closes automatically.
5-B To attach
如圖所示將前面板放在本機的前面，然後輕輕推
入前面板，直至發出喀嗒聲。
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.
安裝示例（6）
Place the front panel on the front side of the unit
as illustrated, then lightly push the front panel
into position until it clicks.
安裝在儀錶板裡
安裝時必須關閉前面板。（6- ）
*
安裝時若前面板開著，以及施以太大的力，都會
造成故障。
Mounting example (6)
Installation in the dashboard
When installing this unit, be sure to close the
front panel of the unit. (6- )
*
If the front panel is opened while installing and
given too much force, it may cause a
malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
|