SonicWALL Security Camera NSA 6600 User Manual

*The included power cord is approved for use only in specific countries or regions. Before using a power cord, verify that it is rated and approved for use in your location. The

power cord is for AC mains installation only. See Safety and Regulatory Information for more information.

10GE

1GE

X14

X15

X12

X13

X10

X11

X18

X19

X16

X17

SDHC

BYPASS

STATUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

Dell SonicWALL Network Security Appliance

NSA 6600

NETWORK SECURITY

Getting Started Guide

Missing Items? If any items are missing from your package, contact Dell SonicWALL Support:

Web: http://www.sonicwall.com/us/Support.html

Email: [email protected]

NSA 6600 Package Contents

Download from Www.Somanuals.com. All Manuals Search And Download.

The Front Panel

SDHC Port

Secure Digital High-Capacity (SDHC) port

for future use

Bypass Status

Turns on when

fail-to-wire bypass

mode is active

Console Port

Access the SonicOS Command Line Interface

MGMT Port (1 GE)

1 Gigabit Ethernet

(CLI) via the enclosed serial CLI cable

Management Interface

10GE

1GE

X14

X15

X12

X13

X10

X11

X18

X19

X16

X17

SDHC

BYPASS

STATUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

USB Ports (2)

For 3G/4G/Analog modem adaptor support

X0-X7 (1 GE)

Reset Button

Press and hold for several seconds to set the

appliance into Safe Mode.

High-speed copper

Gigabit Ethernet ports

X8-X15 (1 GE SFP)

1 Gigabit Ethernet hot-pluggable SFP

interfaces for high-speed ﬁber or

copper Ethernet communication

LED Indicators

Power: Blue: Indicates power supplies are operating correctly

Yellow: Indicates a disconnected power supply

Test: Quick Blinking Yellow: Initializing

Slow Blinking Yellow: SafeMode

Solid Yellow: Test mode

Alarm: Indicates alarm activity in Red LED

M0: Indicates Expansion Module 0 activity in Red LED

X16-X19 (10 GE SFP+)

10 Gigabit Ethernet hot-pluggable ports

*X16, X18, and X19 are designated with a ‘dot’to

signify ports with a direct uplink to the appliance

CPU for maximum throughput ; X17 shares the

CPU uplink with X0-X15.

The Front Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

The Back Panel

Fans (2)

Dual auto-throttling fans for system

temperature control

Power Supply

Provides power to the Dell SonicWALL appliance

by plugging in the AC adaptor and switching the

appliance on

Expansion Bay

For Dell SonicWALL-approved

expansion modules

Warning: Potential Hazard from Fan

This manual contains specific warning and caution statements where they apply. Please read the Safety Instructions before

use! See Product Safety and Regulatory Information, page 57.

The Back Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

Using this Getting Started Guide

The following flow chart illustrates the necessary steps in the process of getting started with your new Dell SonicWALL NSA 6600

appliance.

Configuration Process

Verify

Pre-Configuration

Requirements

Start Up

Management

Computer

Perform Initial

Setup

Registration, Licensing, and Deployment Process

Create a

MySonicWALL

Account

Appliance in

SonicOS

Complete

Deployment

Configuration

Using this Getting Started Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Using this Getting Started Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring the Appliance

In this Section:

This section provides an overview of available WAN types, a section to record configuration information, and initial setup information and

procedures.

• Determining the WAN Type, page 12

• System Requirements, page 12

• Recording Configuration Information, page 13

• Initial Setup, page 14

• Connecting to the Internet, page 17

• Troubleshooting Your Connections, page 19

Download from Www.Somanuals.com. All Manuals Search And Download.

Determining the WAN Type

Note: For more information regarding other supported WAN

types such as Wire Mode or Tap Mode, refer to the

SonicOS Administrator’s Guide.

Before configuring your Dell SonicWALL NSA 6600 appliance,

you will need to determine the type of WAN connection your

setup will use. Dell SonicWALL supports the following types:

• Static—Configures the appliance for a network that uses

static IP addresses.

System Requirements

• DHCP—Configures the appliance to request IP settings from

a DHCP server on the Internet.

Before beginning the setup process, verify that you have:

• An Internet connection

• PPPoE—Point-to-Point Protocol over Ethernet (PPPoE) is

typically used with a DSL modem. If your ISP requires

desktop software, a username, and password, select NAT

with PPPoE mode.

• A Web browser supporting Java Script and HTTP uploads.

Accepted Browser

Browser Version Number

• PPTP—Point-to-Point Tunneling Protocol (PPTP) is used to

connect to a remote server. PPTP typically supports older

Microsoft Windows implementations requiring tunneling

connectivity.

Internet Explorer

8.0 and higher

Chrome

Firefox

Safari

18.0 and higher

16.0 and higher

5.0 and higher

• L2TP—Layer 2 Tunneling Protocol (L2TP) uses IPsec to

connect to a L2TP server and encrypts all data transmitted

from the client to the server. It does not encrypt network traffic

to other destinations. If L2TP is not available in the Setup

Wizard, you can configure it later in the SonicOS

management interface.

Determining the WAN Type

Download from Www.Somanuals.com. All Manuals Search And Download.

Ethernet WAN IP Address:

Select a static IP address for your

Ethernet WAN. This setting only

applies if you are already using an

ISP that assigns a static IP address.

Recording Configuration Information

_____._____._____._____

Use this section to record your configuration information. Be

sure to keep for future reference.

Administrator Information

The default MGMT interface IP address is 192.168.1.254.

Admin Name:

Select an administrator account name.

(default is admin)

Registration Information

Serial Number:

Record the serial number found on

the bottom panel of your

Admin Password:

Select an administrator password.

(default is password)

Dell SonicWALL appliance.

Authentication Code:

Record the authentication code found

on the bottom panel of your

Dell SonicWALL appliance.

Internet Service Provider (ISP) Information

Record the following information about your current Internet

service:

Networking Information

If you are

No information is usually required. However,

connecting with

DHCP

some providers may require a Host Name:

LAN IP Address:

Select a static IP address for your

Dell SonicWALL appliance that is

within the range of your local network.

(default is 192.168.168.168)

_________________________________

_____._____._____._____

Subnet Mask:

If you are

connecting with

Static IP

IP Address: _____._____._____._____

Subnet Mask:_____._____._____._____

Default Gateway: _____._____._____._____

Primary DNS: _____._____._____._____

DNS 2 (optional): _____._____._____._____

DNS 3 (optional): _____._____._____._____

Record the subnet mask for the local

network. Client devices connecting

through the appliance are assigned IP

addresses in this network.

_____._____._____._____

(default is 192.168.168.0)

Recording Configuration Information

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup

The diagram below illustrates how to connect your management computer to the Dell SonicWALL NSA 6600 appliance for initial setup.

Dell SonicWALL Appliance

10GE

1GE

X16

X14

X12

X10

X18

SDHC

BYPASS

STATUS

ALARM

120V AC

(U.S.)

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

MGMT

Management Computer

Ethernet

Initial Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

The following sections provide initial configuration information

and instructions for connecting your Dell SonicWALL NSA 6600

appliance for initial setup.

NSA 6600 LED Activity

The Power LEDs on the front panel illuminate blue when the

appliance is powered on.

• Connecting the MGMT Port, page 15

• Applying Power to the NSA 6600, page 15

• NSA 6600 LED Activity, page 15

The Test LED or Alarm LED may illuminate and blink while the

appliance performs a series of diagnostic tests. When these

LEDs are no longer illuminated and the Power LEDs remain

steadily lit, the Dell SonicWALL NSA 6600 appliance is ready

for configuration. This typically occurs within a few minutes of

turning on the power.

• Using the Setup Wizard, page 16

Connecting the MGMT Port

1. Using the provided Ethernet cable, connect one end of the

cable to the computer you are using to manage the

Dell SonicWALL NSA appliance.

If the Test or Alarm LEDs remain lit after the NSA 6600 has

completed powering on, restart the appliance by disconnecting

the power, waiting 1 minute, then connecting the power again.

2. Connect the other end of the Ethernet cable to the MGMT

port on your Dell SonicWALL NSA appliance.

For a connected MGMT or X0 - X7 port, the Link LED for the

port illuminates green or amber depending on the link

throughput speed, indicating an active connection:

Applying Power to the NSA 6600

Connect the AC power cord from the Dell SonicWALL NSA

appliance into an appropriate power outlet.

• Amber indicates 1 Gbps

• Green indicates 100 Mbps

For further information regarding power requirements, refer to

Product Safety and Regulatory Information, page 57 of this

document.

• A unlit left LED with the right LED lit indicates 10 Mbps

Initial Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Launch the Dell SonicWALL Setup Wizard by clicking the

first Here link. This wizard helps you quickly configure the

Dell SonicWALL appliance to secure your Internet

connection.

3. Follow the on-screen prompts to complete the

Dell SonicWALL Setup Wizard.

Using the Setup Wizard

When you are ready to begin initial setup, configure your

management computer with a static IP address on the

192.168.1.0/24 subnet, such as 192.168.1.20. This allows your

computer to connect to SonicOS via the MGMT interface.

4. A Setup Wizard Summary page displays at the end of the

wizard. Verify the information you’ve entered is correct,

then click Apply.

Note: Be sure to disable pop-up blocking software, or set your

Web browser to allow pop-ups and cookies.

5. Once completed, a Setup Wizard Completion notice

displays.

To access the SonicOS management interface, follow the steps

listed:

1. With your computer connected to the appliance MGMT

port, start your Web browser and navigate to the default

MGMT interface IP address: <http://192.168.1.254>.

6. Click Close.

7. Continue to Connecting to the Internet, page 17 to connect

the appliance for Internet access and then refer to

Registering, Licensing, and Upgrading, page 21 to begin

the registration process.

Initial Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing Your Internet Connection

Connecting to the Internet

Use the following steps to test your Internet connection:

1. After you exit the Setup Wizard, connect your computer to

the X0 (LAN) port.

2. Point your browser to the X0 IP address configured during

initial setup, or to the default <http://192.168.168.168>.

3. When the log in page appears, log into the SonicOS

management interface as admin, using the configured

password or the default, password.

After initial setup is complete, connect the LAN and WAN

interfaces for access to external networks or the Internet. You

cannot reach the Internet or other WAN destinations while

connected to the MGMT interface. For Internet access, connect

to X0 or another configured LAN interface.

4. Open a command prompt window on your computer and

Note: Internet connectivity is needed for the recommended

enter the command: ping sonicwall.com

5. Open another Web browser and navigate to:

<http://www.sonicwall.com>.

product registration process.

Connecting the LAN Port

1. Connect one end of an Ethernet cable to your computer or

to your local network switch or other networking device.

If you can view the Dell SonicWALL home page, you have

configured your Dell SonicWALL NSA 6600 correctly.

If you cannot view the Dell SonicWALL home page, try one of

these solutions:

2. Connect the other end of the Ethernet cable to the X0

(LAN) port on your Dell SonicWALL NSA appliance.

• Renew your management station DHCP address or restart

your management station to accept new network settings from

the DHCP server in the Dell SonicWALL appliance.

Connecting the WAN Port

1. Connect one end of an Ethernet cable to your Internet

connection.

• Restart your Internet router to communicate with the DHCP

client in the Dell SonicWALL appliance.

If you have a router, DSL modem, or cable modem,

connect the Ethernet cable to a LAN port on the router or

modem.

Note: WAN connectivity issues are unrelated to completion of

2. Connect the other end of the Ethernet cable to the X1

the MySonicWALL registration process.

(WAN) port on your Dell SonicWALL NSA appliance.

Connecting to the Internet

Download from Www.Somanuals.com. All Manuals Search And Download.

Internet Access

The diagram below illustrates how to connect your computer to the Dell SonicWALL NSA 6600 appliance for Internet access.

Dell SonicWALL Appliance

10GE

1GE

X14

X12

X10

X18

X16

SDHC

BYPASS

STATUS

ALARM

120V AC

(U.S.)

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

X0 (LAN)

X1 (WAN)

Ethernet

Internet

Connecting to the Internet

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Your LAN Connection

Troubleshooting Your Connections

If you do not see the SonicOS log in prompt when you point

your browser to the X0 (LAN) IP address, consider the

following:

Use the suggestions in this section to troubleshoot your MGMT

and LAN connections.

• Did you correctly enter the IP address for the Dell SonicWALL

NSA 6600 X0 interface into your Web browser, beginning with

“http://” or “https://”?

Troubleshooting Your MGMT Connection

• Did you try restarting your management station while it is

connected to the Dell SonicWALL appliance?

If you cannot connect to the Dell SonicWALL NSA 6600 or the

Setup Wizard does not display, consider the following:

• Are the Local Area Connection settings on your computer set

to one of the following?:

• Did you correctly enter the Dell SonicWALL NSA 6600

management IP address beginning with “http://” or “https://”

in your Web browser?

• Obtain an IP address automatically using DHCP

• A static IP address on the default LAN subnet

(192.168.168.0/24)

• Did you try restarting your management station while it is

connected to the Dell SonicWALL appliance?

• A static IP address on the configured LAN subnet if you

changed it during initial setup

• Are the Local Area Connection settings on your computer set

to a static IP address on the 192.168.1.0/24 subnet?

• Do you have the Ethernet cable connected to your computer

and to the X0 (LAN) port on your appliance?

• Is the Ethernet cable connected to your computer and to the

MGMT port on your appliance?

• Is the connector clip on your network cable properly seated in

the port of the security appliance?

• Is the connector clip on your network cable properly seated in

the port of the security appliance?

Troubleshooting Your Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Your Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

Registering, Licensing, and Upgrading

In this Section:

This section provides instructions for registering, licensing, and upgrading firmware on your Dell SonicWALL NSA 6600 appliance.

• Using MySonicWALL, page 22

• Creating a MySonicWALL Account, page 22

• Registration Overview, page 23

• Registering in SonicOS, page 23

• Alternative Registration Options, page 24

• Security Services and Software, page 25

• Activating & Managing Licenses Using MySonicWALL, page 26

• Upgrading Firmware, page 27

Note: Registration is an important part of the setup process and is necessary in order to receive the benefits of Dell SonicWALL

security services, firmware updates, and technical support.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using MySonicWALL

Creating a MySonicWALL Account

Dell SonicWALL requires a MySonicWALL account prior to

configuring your appliance. If you already have a

MySonicWALL account, you can continue to Registration

Overview, page 23.

A MySonicWALL account is required in order to register the Dell

SonicWALL NSA 6600 appliance. Create a new MySonicWALL

account from any computer by navigating to:

<http://www.mysonicwall.com>.

MySonicWALL is used during registration of your

Dell SonicWALL appliance and to activate or purchase licenses

for security services, support, or software specific to your

Dell SonicWALL device.

To create a MySonicWALL account:

1. In your Web browser, navigate to

<http://www.mysonicwall.com>.

2. In the Login screen, click the Register Now link.

For a High Availability configuration, MySonicWALL provides a

way to associate a secondary unit that can share security

service licenses with your primary appliance.

Note: MySonicWALL registration information is not sold or

shared with any other company.

3. Complete the Registration form, and then click Register.

4. Verify that the information is correct, and then click

Submit.

5. To confirm your account was created, click Continue.

Using MySonicWALL

Download from Www.Somanuals.com. All Manuals Search And Download.

Registration Overview

Registering in SonicOS

Although there are several ways to register your new

Dell SonicWALL appliance, Dell SonicWALL recommends

registering your appliance through the SonicOS management

interface.

After you have completed the Setup Wizard and can

successfully connect to your Dell SonicWALL NSA 6600

appliance, you are ready to register the security appliance.

1. Log into your Dell SonicWALL appliance. Use the defaults:

<http://192.168.168.168> and admin / password, or if you

changed these fields during the initial setup process, use

the new IP address and credentials. Then, click Login.

2. Navigate to the System > Status page.

A message displays at the top of the screen that your

Dell SonicWALL appliance is not registered. Click the

This section describes how to register and license your

appliance through SonicOS, as well as the alternate options

available on MySonicWALL.

Note: If you haven’t created a MySonicWALL account, see

Creating a MySonicWALL Account, page 22.

3. Enter your MySonicWALL username and password in the

appropriate fields. Then, click Submit.

If you haven’t created a MySonicWALL account, see

Creating a MySonicWALL Account, page 22.

4. In the Licenses > License Management page, specify a

Friendly Name for the Dell SonicWALL appliance.

5. Complete the Product Survey. Then, click Submit.

Acknowledge the registration completion notification by

clicking Continue. The Licenses > License Management

page now lists all the Security Services associated to your

appliance.

Registration Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

Synchronizing Licenses Manually

Alternative Registration Options

To manually synchronize licenses with MySonicWALL from the

SonicOS interface:

If you have registered your Dell SonicWALL appliance through

the SonicOS interface, you can continue to Security Services

and Software, page 25.

1. Log in to your appliance and navigate to the System >

Licenses page.

2. Scroll to the Manage Security Services Online section.

3. Click the Synchronize button to synchronize licenses with

Although Dell SonicWALL strongly recommends registering

your appliance using the SonicOS interface, you can optionally

use MySonicWALL to register your appliance.

MySonicWALL.

Using the License Keyset

Registering on MySonicWALL

1. Log in to your MySonicWALL account. If you do not have

an account, create one at:

<http://www.mysonicwall.com>.

2. Type the Dell SonicWALL appliance serial number in the

3. Type a Friendly Name for the appliance.

4. Select the Product Group from the dropdown list, if

MySonicWALL provides an encrypted license keyset for each

registered appliance. You can use the license keyset to

manually apply all active licenses to your Dell SonicWALL

appliance.

1. Log in to your MySonicWALL account and click the link for

your appliance.

2. On the Services Management page, click the View

License Keyset link.

3. Click the encrypted text, then click Ctrl+A to select the

entire keyset, then copy it to your clipboard.

available.

5. Enter the Authentication Code, and then click Submit.

The Authentication Code is located on the bottom panel of

your appliance.

4. Log in to your appliance and navigate to the System >

Licenses page.

5. Scroll down to the Manual Upgrade section and enter the

keyset in the appropriate field.

6. Enter the requested information on the Product Survey

page, then click Submit.

6. When finished entering the keyset, click Submit.

Alternative Registration Options

Download from Www.Somanuals.com. All Manuals Search And Download.

The following products and services are available for the Dell

SonicWALL NSA 6600:

Security Services and Software

• Service Bundles:

• Comprehensive Gateway Security Suite

• McAfee: Client/Server Anti-Virus Suite

The My Products > Product Management page in

MySonicWALL lists security services, support options, and

software that you can purchase or try with a free trial. For

details, click the Name of the product. The Service

Management page displays with the most recent details.

• Gateway Services:

• AppControl & Visualization

• Gateway AV / Anti-Spyware / Intrusion Prevention

Service

Licensing Security Services

• Content Filtering: Premium Edition

• Stateful High Availability

• Comprehensive Anti-Spam Service (CASS)

• Deep Packet Inspection for SSL (DPI-SSL)

To license a security service, complete one of the following from

the MySonicWALL Service Management page:

• Free Trial of Service—Click the Try icon in the Action column

for the security service you wish to try for a 30-day free trial.

The free trial immediately activates and notifies you of the trial

expiration date. The Service Management page displays

updated information about the free trial service.

• Desktop & Server Software:

• McAfee Enforced Client Anti-Virus and Anti-Spyware

• Client Content Filtering

• Global VPN Client Enterprise

• WAN Acceleration Software

• WAN Acceleration Client

• Virtual Assist

• Purchase a Service—Click the Cart icon to purchase a

security service. In the Buy Service page, specify the quantity

of licenses wanted, then click Add to Cart. Once the item(s)

have been added, click the Checkout button. Follow the

instructions to complete your purchase.

• Analyzer

• SSL VPN Client License

• Scrutinizer

The Applicable Services section lists the services available for

your product. The Status of a service indicates whether the

service is Licensed, Not Licensed, or Expired. The Action

column lets you purchase or activate additional services.

• Support Services:

• Dynamic Support 24x7

• Software and Firmware Updates

• Hardware Warranty

Security Services and Software

Download from Www.Somanuals.com. All Manuals Search And Download.

To activate your service licenses, log in to your MySonicWALL

account and perform the following tasks:

Activating & Managing Licenses Using

MySonicWALL

1. In the MySonicWALL My Products page, click the

appliance Name. The Applicable Services table displays

a list of services that are already licensed on your

Dell SonicWALL appliance.

If you registered your appliance through SonicOS, all licensed

services are already activated. You can continue to Upgrading

Firmware, page 27.

Note that your initial purchase may have included security

services or other software bundled with the appliance.

These licenses are enabled on MySonicWALL when the

appliance is delivered to you.

If you purchased a service subscription or upgrade from a sales

representative separately, you will have an Activation Key for

the service. This key is emailed to you after online purchases,

or is on the front of the certificate that was included with your

purchase.

2. Locate the service in the Applicable Services section and

click the key icon to activate the service.

3. Type or paste your key into the Activation Key field, and

then click Submit.

After activating the service, you will see a Status and

Expiration date in the respective columns when you return

to the Service Management page.

Activating & Managing Licenses Using MySonicWALL

Download from Www.Somanuals.com. All Manuals Search And Download.

Saving a Backup Copy of Your Preferences

Upgrading Firmware

Before beginning the update process, make a system backup

on your Dell SonicWALL appliance. The backup feature saves a

copy of the current system state, firmware, and configuration

settings on your Dell SonicWALL security appliance, protecting

all your existing settings in the event that it becomes necessary

to return to a previous configuration state.

Dell SonicWALL recommends that you run the latest available

firmware on your security appliance. You will need to upgrade

the factory-installed firmware to the latest version available on

MySonicWALL.

The following procedures are for upgrading an existing

SonicOS firmware image to a newer version:

In addition to creating a system backup, you can export the

configuration preferences file to your local management station.

This file serves as an external backup of the configuration

preferences, and can be imported back into the

Dell SonicWALL security appliance if it is necessary to reboot

the firmware with factory default settings.

• Saving a Backup Copy of Y o ur Preferences, page 27

• Obtaining the Latest Firmware, page 28

• Upgrading the Firmware, page 28

• Using SafeMode to Upgrade Firmware, page 29

Perform the following procedures to save a system backup on

your appliance and export configuration settings to a file on your

local management station:

1. On the System > Settings page, click Create Backup.

SonicOS takes a “snapshot” of your current system state,

firmware, and configuration preference, and makes it the

new System Backup firmware image. Clicking Create

Backup overwrites the existing System Backup image, if

any. The System Backup entry displays in the Firmware

Management table.

2. To export your settings to a local file, click Export Settings.

A popup window displays the name of the saved file.

Upgrading Firmware

Download from Www.Somanuals.com. All Manuals Search And Download.

Obtaining the Latest Firmware

Upgrading the Firmware

To obtain a new SonicOS firmware image file for your

Dell SonicWALL security appliance, perform the following

steps:

Perform the following steps to upload new firmware to your

Dell SonicWALL appliance and use your current configuration

settings upon startup.

1. In a browser on your management computer, log into your

MySonicWALL account at <http://www.mysonicwall.com>.

Tip: The appliance must be properly registered before it can

be upgraded. Refer to Registering in SonicOS, page 23

for more information.

2. In MySonicWALL, click Downloads in the left navigation

pane to display the Download Center screen.

3. Select NSA 6600 Firmware in the Software Type

dropdown list to display available firmware versions.

4. Locate the firmware version you want, and click the link to

download it to a convenient location on your computer. You

can download the Release Notes and other associated

files in the same way.

1. Download the SonicOS firmware image file from

MySonicWALL and save it to a convenient location on your

local computer.

2. On the System > Settings page in SonicOS, click Upload

New Firmware.

3. Browse to the location where you saved the SonicOS

firmware image file, select the file and click the Upload

button.

After the firmware finishes uploading, it will display in the

Firmware Management table.

4. Click the Boot icon in the row for Uploaded Firmware -

New! to restart the appliance with the new firmware using

your existing configuration settings.

5. In the confirmation dialog box, click OK. The appliance

restarts and then displays the log in page.

6. Enter your user name and password. Your new SonicOS

image version information is listed on the System > Status

page.

Upgrading Firmware

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Select the boot icon in the row for one of the following:

• Uploaded Firmware - New!

Using SafeMode to Upgrade Firmware

If you are unable to connect to the SonicOS management

interface, you can restart the security appliance in SafeMode.

The SafeMode feature allows you to recover quickly from

uncertain configuration states with a simplified management

interface that includes the same settings available on the

System > Settings page.

Use this option to restart the appliance with your current

configuration settings.

• Uploaded Firmware with Factory Default Settings-

New!

Use this option to restart the appliance with default

configuration settings.

6. In the confirmation dialog box, click OK to proceed.

Perform the following steps to use SafeMode to upgrade

firmware on the Dell SonicWALL security appliance:

7. To connect to SonicOS through the LAN or WAN interface

of the appliance, disconnect your computer from the

MGMT port, and reconfigure it to automatically obtain an IP

address and DNS server address, or reset it to its normal

static values.

1. Connect your computer to the MGMT port on the appliance

and configure your IP address with an address on the

192.168.1.0/24 subnet, such as 192.168.1.20.

2. To force the appliance into SafeMode, use a narrow,

straight object, like a straightened paper clip or a toothpick,

to press and hold the Reset button on the front of the

Dell SonicWALL appliance for at least twenty seconds, until

the Test light begins blinking. See The Front Panel, page 7

to locate the Reset button.

8. Connect your computer to the local network and point your

browser to the LAN or WAN IP address of the

Dell SonicWALL appliance.

9. After successfully booting the firmware, the log in screen

displays. If you restarted with factory default settings, enter

the default user name and password (admin / password) to

access the SonicOS management interface.

The Test light begins to blink when the Dell SonicWALL

security appliance has rebooted into SafeMode.

3. Enter 192.168.1.254 into your computer’s Web browser to

access the SafeMode management interface.

4. Click Upload New Firmware, and then browse to the

location where you saved the SonicOS firmware image,

select the file and click the Upload button.

Upgrading Firmware

Download from Www.Somanuals.com. All Manuals Search And Download.

Upgrading Firmware

Download from Www.Somanuals.com. All Manuals Search And Download.

Deployment Scenarios

In this Section:

This section provides configuration overviews, as well as deployment scenarios for your Dell SonicWALL NSA 6600.

• Advanced Deployment Scenarios, page 32

• Configuring NAT Mode Gateway, page 36

• Configuring a Stateful HA Pair, page 37

• Configuring L2 Bridge Mode, page 43

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Deployment Scenarios

Select a deployment scenario that best fits your network scheme. Reference the table below and the diagrams on the following pages for

help in choosing a scenario.

Current Gateway Configuration

No gateway appliance

New Gateway Configuration

Use Scenario

Single NSA appliance as a primary gateway.

Pair of NSA appliances for high availability.

Scenario A: NAT Mode Gateway, page 33

Scenario B: Stateful HA Pair, page 34

Scenario A: NAT Mode Gateway, page 33

Existing Internet gateway appliance

NSA as replacement for an existing gateway

appliance.

NSA in addition to an existing gateway

appliance.

Scenario C: L2 Bridge Mode, page 35

Scenario B: Stateful HA Pair, page 34

Existing SonicWALL gateway appliance NSA appliance in addition to an existing

Dell SonicWALL gateway appliance.

Internet or

LAN Segment

10GE

1GE

X18

X19

X16

X17

X14

X15

X12

X13

X10

X11

10GE

1GE

SDHC

X18

X19

X16

X17

X14

X15

X12

X13

X10

X11

SDHC

BYPASS

ST TUS

ALARM

BYPASS

ST TUS

ALARM

TEST

PWR

TEST

PWR

SonicWALL NSA 6600

MGMT

CONSOLE

SonicWALL NSA 6600

CONSOLE

MGMT

ISP

Internet

10GE

1GE

X18

X19

X16

X17

X14

X15

X12

X13

X10

X11

SDHC

BYPASS

ST TUS

ALARM

TEST

PWR

SonicWALL NSA 6600

MGMT

CONSOLE

SonicPoint

10GE

1GE

X18

X19

X16

X17

X14

X15

X12

X13

X10

X11

SDHC

BYPASS

STATUS

ALARM

TEST

PWR

Internet

SonicWALL NSA 6600

MGMT

CONSOLE

SonicPoint

LAN Zone

WLAN Zone

DMZ Zone

LAN Zone

WLAN Zone

Local Network

Advanced Deployment Scenarios

Download from Www.Somanuals.com. All Manuals Search And Download.

Scenario A: NAT Mode Gateway

For new network installations or installations where the

NSA 6600 is replacing the existing network gateway.

Dell SonicWALL NSA Appliance

10GE

1GE

X18

X16

X14

X12

X10

SDHC

In this scenario, the NSA 6600 is configured in NAT mode to

operate as a single network gateway. Two Internet connections

may be routed through the Dell SonicWALL appliance for load

balancing and failover purposes. Because only a single

Dell SonicWALL appliance is deployed, the added benefits of

high availability with a stateful synchronized pair are not

available.

BYPASS

STATUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

ISP 1

Internet

SonicPoint

LAN Zone

WLAN Zone

DMZ Zone

To set up this scenario, follow the steps covered in:

• Configuring NAT Mode Gateway, page 36

Advanced Deployment Scenarios

Download from Www.Somanuals.com. All Manuals Search And Download.

Scenario B: Stateful HA Pair

For network installations with two Dell SonicWALL NSA 6600

appliances configured as a stateful synchronized pair for

redundant High Availability (HA) networking.

Dell SonicWALL NSA Appliance 2

Dell SonicWALL

HA/Failover Pair

10GE

1GE

X18

X16

X14

X12

X10

SDHC

BYPASS

ST TUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

In this scenario, one NSA 6600 operates as the Primary

gateway device and the other NSA 6600 is in Idle mode. All

network connection information is synchronized between the

two devices so that the Secondary appliance can seamlessly

switch to Active mode without dropping connections if the

Primary device loses connectivity.

HA Control Link

HA Data Link

10GE

1GE

X18

X16

X14

X15

X12

X13

X10

X11

SDHC

BYPASS

STATUS

ALARM

TEST

PWR

Internet

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

Dell SonicWALL NSA Appliance 1

To set up this scenario, follow the steps covered in:

• Configuring a Stateful HA Pair, page 37

Local Network

Advanced Deployment Scenarios

Download from Www.Somanuals.com. All Manuals Search And Download.

Scenario C: L2 Bridge Mode

For network installations where the Dell SonicWALL NSA 6600

is running in tandem with an existing network gateway.

Third Party Gateway

Internet or

LAN Segment 2

L2 Bridge Link

Dell SonicWALL NSA Appliance

In this scenario, the original gateway is maintained. The Dell

SonicWALL NSA 6600 is integrated seamlessly into the existing

network, providing the benefits of deep packet inspection and

comprehensive security services on all network traffic.

10GE

1GE

X18

X16

X14

X12

X10

SDHC

BYPASS

ST TUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

SonicPoint

L2 Bridge Mode employs a secure learning bridge architecture,

enabling it to pass and inspect traffic types that cannot be

handled by many other methods of transparent security

appliance integration. Using L2 Bridge Mode, a Dell SonicWALL

security appliance can be non-disruptively added to any

Ethernet network to provide in-line deep-packet inspection for

network traffic.

LAN Zone

WLAN Zone

To set up this scenario, follow the steps covered in:

• Configuring L2 Bridge Mode, page 43

Advanced Deployment Scenarios

Download from Www.Somanuals.com. All Manuals Search And Download.

Dell SonicWALL NSA Appliance

Configuring NAT Mode Gateway

10GE

1GE

X18

X16

X14

X12

X10

SDHC

BYPASS

ST TUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

This section provides an overview of a Dell SonicWALL NSA

6600 appliance operating as a single network gateway in NAT

mode, which is the default mode for a newly configured

NSA 6600. This section is relevant to administrators following

deployment Scenario A.

Internet

X16

SonicPoint

Note: No additional configuration is necessary to deploy your

appliance as a single network gateway in Many-to-One

NAT mode.

LAN Zone

DMZ Zone

WLAN Zone

The Dell SonicWALL NSA 6600 ships with the internal DHCP

server active on the LAN port. However, if a DHCP server is

already active on your LAN, the Dell SonicWALL appliance will

disable its own DHCP server to prevent conflicts.

Overview of NAT Mode

Network Address Translation (NAT) allows private IP addresses

on internal networks to be mapped to at least one public IP

address on the WAN interface of the Dell SonicWALL security

appliance. Outbound traffic from the internal network uses

many-to-one NAT address mappings for their LANs, WLANs,

and other internal networks.

As shown in the illustration, ports X1 and X0 are preconfigured

as WAN and LAN, respectively. The remaining ports (X2-X17)

can be configured to meet the needs of your network. In the

example diagram, certain interfaces are configured for specific

zones:

All traffic in SonicOS must go through both an access rule and a

NAT policy, a fundamental part of the NAT Mode architecture.

The NAT policy is even used for traffic that needs no IP address

translation, such as traffic traveling between two different LAN

interfaces, traffic on the simplest types of VPNs, or through

Layer 2 Bridge Mode / Transparent Mode configurations.

• X1—WAN

• X0—LAN

• X12—Wireless LAN

• X16—DMZ

Configuring NAT Mode Gateway

Download from Www.Somanuals.com. All Manuals Search And Download.

NAT policies allow the flexibility to control Network Address

Translation based on matching combinations of Source IP

address, Destination IP address, and Destination Services.

Policy-based NAT allows you to deploy different types of NAT

simultaneously.

Configuring a Stateful HA Pair

This section provides instructions for configuring a pair of Dell

SonicWALL NSA 6600 appliances for Stateful High Availability

(HA). This section is relevant to administrators following

deployment Scenario B.

For configuration procedures and information regarding the

different types of NAT policies, such as Many-to-One, One-to-

One, or One-to-Many Load Balancing, refer to the SonicOS

Administrator’s Guide.

A Stateful HA pair operates in NAT mode by default, similar to

Scenario A, with the added benefit of high availability.

See the following sections:

• Initial High Availability Setup, page 38

• Configuring High Availability Settings, page 38

• Configuring HA Monitoring Settings, page 39

• Configuring Optional HA Settings, page 40

• Configuring HA Advanced Settings, page 40

• HA License Configuration Overview, page 41

• Completing HA Pair Association, page 41

• Verifying High Availability Setup, page 42

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

• Ensure the Primary and Secondary security appliances’ LAN,

WAN, and other interfaces are properly connected for failover.

Dell SonicWALL NSA Appliance 2

Dell SonicWALL

HA/Failover Pair

10GE

1GE

X18

X16

X14

X12

X10

SDHC

• Connect the HA Control and Data Links on the Primary and

Secondary appliances with appropriate cables.

BYPASS

ST TUS

ALARM

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

HA Control Link

HA Data Link

• Turn on the Primary Dell SonicWALL security appliance first.

Then, turn on the Secondary Dell SonicWALL security

appliance.

Dell SonicWALL NSA Appliance 1

10GE

1GE

X18

X16

X14

X12

X10

SDHC

BYPASS

ST TUS

ALARM

Internet

TEST

PWR

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

Configuring High Availability Settings

The first task in setting up HA after completing Initial Setup,

page 14 is configuring the High Availability > Settings page

on the Primary Dell SonicWALL security appliance. Once you

configure HA on the Primary appliance, it communicates the

settings to the Secondary appliance.

Local Network

Initial High Availability Setup

To configure HA on the Primary Dell SonicWALL, log in to your

Primary appliance and perform the following steps:

Before you begin the configuration of HA on the Primary

Dell SonicWALL security appliance, perform the following

tasks:

1. Navigate to the High Availability > Settings page.

2. On the General tab, select Active / Idle from the Mode

dropdown menu.

3. Select the Enable Stateful Synchronization checkbox.

• Determine which interfaces should be used as the HA Control

Link and the HA Data Link. Remember, they must be the

same ports on each appliance.

4. Next, navigate to the HA Devices tab and type in the serial

number for the Secondary appliance.

5. Navigate to the HA Interfaces tab and specify an HA

• On the bottom panel of the appliance that will run as the

Secondary device, locate the serial number and write the

number down. You need to enter this number in the High

Availability > Settings > HA Devices page.

Control Interface and an HA Data Interface.

6. Click Apply to save these settings. All settings will be

synchronized to the Secondary appliance, and the

Secondary appliance will reboot.

• Verify that the Primary and Secondary appliances are

registered on MySonicWALL, running the same SonicOS

versions.

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

2. In the Primary IP Address field, enter the unique LAN or

Configuring HA Monitoring Settings

WAN management IP address of the Primary appliance.

After configuring the HA settings, you need to configure the

Monitoring settings for the LAN or WAN.This includes

configuring unique IP addresses for each appliance in the

Stateful HA pair. You will need to log into the appliances using

these IP addresses in order to complete the registration process

from within SonicOS, which will allow license sharing and

synchronization.

3. In the Secondary IP Address field, enter the unique LAN

or WAN management IP address of the Secondary

appliance.

4. Select the Allow Management on Primary/Secondary IP

Address checkbox.

5. Optionally Enable Physical / Link Monitoring by selecting

the checkbox.

6. Optionally enable Logical / Probe IP Address by selecting

the checkbox and providing the IP Address of the target

host.

Navigate to the High Availability > Monitoring page to

configure the Monitoring settings.

1. Click the Configure icon of the Interface for which you

want to edit settings. The Edit HA Monitoring dialog box

displays.

7. Click OK.

You can repeat these steps to configure Monitoring on other

interfaces.

For more information regarding the optional settings, see the

SonicOS Administrator’s Guide.

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Set the Probe Interval for the interval in seconds between

communication with upstream or downstream systems.

Dell SonicWALL recommends that you set the interval for

at least 5 seconds. You can set the Probe IP Address(es)

on the High Availability > Monitoring screen.

4. Set the Probe Count, which is the number of consecutive

probes before the appliance considers the network path

unreachable or broken. The default count is 3.

Configuring Optional HA Settings

The following settings are optional. You can configure these

settings from the High Availability > Settings page.

1. To backup the firmware and settings when you upgrade

the firmware version, select the Generate/Overwrite

Backup Firmware and Settings When Upgrading

Firmware checkbox.

5. The Election Delay Time is the number of seconds

allowed for internal processing between the two units in the

HA pair before one of them takes the primary role.

Dell SonicWALL recommends leaving this field at its

default setting. This field can be tuned later as necessary

for your specific network environment.

6. Enable the Active / Idle Failover only when ALL

aggregate links are down checkbox to treat the

aggregated link as down (causing a failover) only if all

member links are down.

2. Select the Enable Virtual MAC checkbox to allow the

Primary and Secondary appliances to share a single MAC

address. This greatly simplifies the process of updating

network ARP tables and caches when a failover occurs.

Only the WAN switch that the two appliances are

connected to needs to be notified. All outside devices will

continue to route to the single shared MAC address.

3. Click Apply to save any of the settings on this page.

Configuring HA Advanced Settings

7. Select the Include Certificates/Keys checkbox to have

the appliances synchronize all certificates and keys.

8. Click Synchronize Settings to synchronize the settings

The following settings are optional. You can configure the

following settings from the High Availability > Advanced

page.

between the Primary and Secondary appliances.

9. Click Synchronize Firmware if you previously uploaded

new firmware to your Primary appliance while the

Secondary appliance was offline, and it is now online and

ready to upgrade to the new firmware.

1. Adjust the Heartbeat Interval to control how often the two

units communicate. The default and recommended

minimum is 1000 milliseconds.

2. The Failover Trigger Level sets the number of heartbeats

that can be missed before failing over. Dell SonicWALL

recommends leaving this field at its default setting. This

field can be tuned later as necessary for your specific

network environment.

Synchronize Firmware is typically used after taking your

Secondary appliance offline while you test a new firmware

version on the Primary appliance before upgrading both

appliances to it.

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

10. Click Force Active / Idle Failover to force a failover

Completing HA Pair Association

between your Primary and Secondary appliances.

You will need to associate the two appliances on

11. Click Accept to retain the settings on this screen.

MySonicWALL. The second appliance will automatically share

the Security Services licenses of the primary appliance.

HA License Configuration Overview

If the second appliance has not yet been registered, follow the

steps listed in Registering on MySonicWALL, page 24 to

association with the Primary.

You can configure HA license synchronization by associating

two Dell SonicWALL security appliances as HA Primary and HA

Secondary on MySonicWALL.

You must purchase a single set of security service licenses for

the HA Primary appliance. To use Stateful HA, you must first

activate the Stateful High Availability Upgrade license for the

primary unit in SonicOS. This is automatic if your appliance is

connected to the Internet. See Registering, Licensing, and

Upgrading, page 21.

Once both appliances are registered, you can then follow the

steps below to associate the two Dell SonicWALL appliances.

1. Log in to your MySonicWALL account.

2. Click My Products from the left navigation bar.

3. On the My Products page, scroll down to find the appliance

that you want to use as the parent, or Primary, appliance.

Click the product Name or Serial Number.

4. On the Service Management page, scroll down to the

Associated Products section.

License synchronization is used during HA so that the

Secondary appliance can maintain the same level of network

protection provided before the failover.

5. Under Associated Products, click HA Secondary.

6. On the My Product page, in the text boxes under Associate

New Products, type the Serial Number and the Friendly

Name of the appliance that you want to associate as the

child, or Secondary, appliance.

7. Select the group from the Product Group dropdown list.

The product group setting specifies the MySonicWALL

users who can upgrade or modify the appliance.

8. Click Associate.

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Log in to the SonicOS management interface of the

Primary appliance using the unique IP address assigned

on the High Availability > Monitoring page.

10. Navigate to the System > Status page and click the

registration link. This allows the unit to synchronize with the

Dell SonicWALL license server and share licenses with the

associated appliance.

From your management workstation, test connectivity through

the Secondary appliance by accessing a site on the public

Internet – note that the Secondary appliance, when active,

assumes the complete identity of the Primary, including its IP

addresses and Ethernet MAC addresses.

Log into the Secondary Dell SonicWALL appliance’s unique

LAN/WAN IP address. The management interface should now

display Logged Into: Secondary Dell SonicWALL Status:

Active in the upper right-hand corner.

11. Then, log in to the SonicOS management interface of the

Secondary appliance using its unique IP address.

12. Navigate to the System > Licenses page and click the

Synchronize Licenses button. This ensures that both the

Primary and Secondary appliances successfully

synchronize with the Dell SonicWALL license server and

share licenses.

Now, turn the Primary appliance back on, wait a few minutes,

then log back into the management interface. If stateful

synchronization is enabled (automatically disabling preempt

mode), the management GUI should still display Logged Into:

Backup Dell SonicWALL Status: Active in the upper-right-

hand corner.

This completes the HA association on MySonicWALL and

ensures that both appliances can share licenses.

If you are using the Physical/Logical Monitoring feature,

experiment with disconnecting each monitored link to ensure

correct configuration.

Verifying High Availability Setup

Once you have configured the HA settings on the Primary

Dell SonicWALL appliance, log in to the Primary appliance’s

unique LAN/WAN IP address. Note that the management

interface displays Logged Into: Primary Dell SonicWALL

Status: Active in the upper right-hand corner.

To verify that the Primary and Secondary Dell SonicWALL

security appliances are functioning correctly, wait a few

minutes, then turn off the Primary device. The Secondary

security appliance should quickly take over.

Configuring a Stateful HA Pair

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection Overview

Configuring L2 Bridge Mode

Connect the X1 port on your Dell SonicWALL NSA 6600 to the

LAN port on your existing Internet gateway device. Then

connect the X0 port on your Dell SonicWALL to your LAN

resources.

This section provides instructions to configure the Dell

SonicWALL NSA 6600 appliance in tandem with an existing

Internet gateway device. This section is relevant to users

following deployment Scenario C.

Network Gateway

See the following sections:

LAN

Dell SonicWAL L NSA Appliance

Internet or

LAN Segment 2

10GE

1GE

X18

X16

X14

X12

X10

SDHC

BYPASS

STATUS

ALARM

• Connection Overview, page 43

TEST

PWR

L2 Bridge Link

SonicWALL NSA 6600

CONSOLE

MGMT

X19

X17

X15

X13

X11

• Configuring the Primary Bridge Interface, page 43

• Configuring the Secondary Bridge Interface, page 44

Network Resources

Configuring the Primary Bridge Interface

The primary bridge interface is connected to your existing

Internet gateway device. The only step involved in setting up

your primary bridge interface is to ensure that the WAN

interface is configured for a static IP address. You will need this

static IP address when configuring the secondary bridge.

Note that the primary bridge interface must have a static IP

assignment.

Configuring L2 Bridge Mode

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Configure management options (HTTP, HTTPS, Ping,

SNMP, SSH, User log ins, or HTTP redirects).

Configuring the Secondary Bridge Interface

1. Navigate to the Network > Interfaces page from the

navigation panel.

Note: Do not enable Never route traffic on this bridge-pair

unless your network topology requires that all packets

entering the L2 Bridge remain on the L2 Bridge

segments. You may optionally enable the Block all

non-IPv4 traffic setting to prevent the L2 bridge from

passing non-IPv4 traffic.

2. Click the Configure icon in the right column of the X0 (LAN)

interface.

3. In the IP Assignment drop-down, select Layer 2 Bridged

Mode.

4. In the Bridged to drop-down, select the X1 interface.

Configuring L2 Bridge Mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Support and Training Options

In this Section:

This section provides overviews of customer support and training options for the Dell SonicWALL NSA 6600.

• Customer Support, page 46

• Knowledge Portal, page 46

• User Forums, page 47

• Training, page 47

• Related Documentation, page 48

• Additionally Supported Languages, page 48

Download from Www.Somanuals.com. All Manuals Search And Download.

Customer Support

Knowledge Portal

Designed for customers with Dell SonicWALL NSA solutions,

Dell SonicWALL 24x7 Support is an around-the-clock support

service that includes phone, email and Web-based technical

support, software and firmware updates and upgrades and

Advance Exchange hardware replacement. Please Note:

Continuous support is recommended on all NSA products.

The Knowledge Portal is a resource which allows users to

search for Dell SonicWALL documents based on the following

types of search tools:

• Browse

• Search for keywords

• Full-text search

For further information, visit:

http://www.sonicwall.com/us/en/support/Services.html

<http://www.sonicwall.com/us/support/kb.asp>

Customer Support

Download from Www.Somanuals.com. All Manuals Search And Download.

User Forums

Training

The Dell SonicWALL User Forums is a resource that provides

users the ability to communicate and discuss a variety of

security and appliance subject matters. In this forum, the

following categories are available for users:

Dell SonicWALL offers an extensive sales and technical training

curriculum for Network Administrators, Security Experts and

Dell SonicWALL Medallion Partners who need to enhance their

knowledge and maximize their investment in Dell SonicWALL

Products and Security Applications. Dell SonicWALL Training

provides the following resources for its customers:

• Firewall

• Networking

• E-Training

• Instructor-Led Training

• Custom Training

• Technical Certification

• Authorized Training Partners

• Installation / Upgrading

• VPN and VPN Client

• SonicPoint and Wireless

• 3G/4G WAN

• Security Services

• GMS and Analyzer

• Secure Remote Access (E-Class / SMB)

• Mobile Connect

For further information, visit:

<http://training.sonicwall.com/>

• Email Security

• Continuous Data Protection

• Scrutinizer

• WAN Acceleration (WXA)

For further information, visit:

<https://forum.sonicwall.com/>

User Forums

Download from Www.Somanuals.com. All Manuals Search And Download.

Related Documentation

Download from Www.Somanuals.com. All Manuals Search And Download.

ローカライズ版ファームウェアおよびドキュメ

ントについて

펌웨어 및 문서 한글화 안내

Dell SonicWALL Getting Started 가이드 , Quick Start 가이드 ,

사용자 가이드 , 어플라이언스 펌웨어 및 다양한 엔드유져 클라

이언트가 다국어를 지원합니다 . 다음에서 사용 가능한 한국어

문서를 찾아 보세요 . http://www.sonicwall.com/apac/en/ko/

documents.html.

Dell SonicWALL 導入ガイド、クイックスタートガイド、ユー

ザガイド、装置用ファームウェア、および多彩なエンドユー

ザクライアントが複数の言語で利用できるようになりました。

利用可能な日本語ドキュメントは、 http://www.sonicwall.com/

japan/documents/support_document.html をご覧下さい。

Getting Started 가이드 또는 Quick Start 가이드에 있는 절차에

따라 http://www.mysonicwall.com 에서 제품 등록을 하세요 .

제품 등록 후 , MySonicWALL 에서 적용 가능한 한국어 펌웨어

또는 사용자 클라이언트 소프트웨어를 확인할 수 있습니다 .

새로운 버젼은 사용 가능할 때 등록됩니다 . 그러므로 , 추가되

는 한국어 펌웨어 , 소프트웨어와 문서가 있는지 주기적으로 체

크하세요 .

導入ガイドまたはクイックスタートガイドの手順に沿って、

MySonicWALL (http://www.mysonicwall.com) で製品を登録しま

す。製品の登録後に、利用可能なファームウェアまたはエンド

ユーザクライアントを MySonicWALL 上で確認できます。新し

いリリースは利用可能になると公開されるので、ファームウェ

ア、ソフトウェア、およびドキュメントを定期的に確認してく

ださい。

Additionally Supported Languages

Download from Www.Somanuals.com. All Manuals Search And Download.

Notificação de Firmware e Documentação

Localizada

As Guias de noções básicas, Guias de início rápido, Guias de

Usuário, firmware de aplicações, e varios clientes de usuário

final de Dell SonicWALL estão agora disponíveis em varias

línguas. Pode encontrar a documentação disponível em

Português em http://www.sonicwall.com/br/pt/.

Siga as instruções da Guia de noções básicas ou Guia de início

rápido para registrar seu produto em MySonicWALL no

http://www.mysonicwall.com. Depois de registrar o produto,

você pode procurar firmaware ou clientes de usuário final

aplicáveis em MySonicWALL. Novos lançamentos são

publicados tão pronto estejam disponíveis, assim que por favor

visite periodicamente esta página para ver firmware, software e

documentos adicionais.

Additionally Supported Languages

Download from Www.Somanuals.com. All Manuals Search And Download.

Rack Mounting Instructions

In this Section:

This section provides illustrated rack mounting instructions for the Dell SonicWALL NSA 6600. For more information on rack mounting

requirements, see Product Safety and Regulatory Information, page 57.

Download from Www.Somanuals.com. All Manuals Search And Download.

Rack Mounting Instructions

Assemble the Slide Rail

Fasten 4 screws to the rail.

WASHERS*8

M4 SCREW*8

Rack Mounting Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Assemble the Slide Rail

Fasten two-sided screws to the rail.

M5 SCREW*8

M5 Nut*8

Rack Mounting Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Assemble Inner Rail to Chassis

Fasten 6 screws to attach the inner channel onto the chassis.

M4 SCREW*6

Rack Mounting Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Insert Chassis to Frame

Slide inner channel into rails.

Push hook down to separate.

Rack Mounting Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Rack Mounting Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Safety and Regulatory Information

In this Section:

This section provides regulatory along with trademark and copyright information.

• Safety and Regulatory Information, page 58

• Warranty Information, page 62

• Copyright Notice, page 62

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Reliable grounding of rack-mounted equipment must be maintained. Particular

attention must be given to power supply connections other than direct

connections to the branch circuits, such as power strips.

The included power cord is approved for use only in specific countries or

regions. Before using a power cord, verify that it is rated and approved for use in

your location.

Safety and Regulatory Information

Regulatory Model/Type

1RK27-0A5

Product Name

NSA 6600

Thumbscrews should be tightened with a tool after both installation and

subsequent access to the rear of the product.

Warning of Potential Hazard from Fan

Safety Instructions

The following conditions are required for proper installation:

•

The Dell SonicWALL appliance is designed to be mounted in a standard 19-inch

rack mount cabinet.

•

Before replacing the fan unit, carefully read and follow the instructions provided

with the unit.

Use the mounting hardware recommended by the rack manufacturer and ensure

that the rack is adequate for the application.

•

Ensure that no water or excessive moisture can enter the unit.

Allow unrestricted airflow around the unit and through the vents on the side of

the unit. A minimum of 1 inch (25.44mm) clearance is recommended.

Route cables away from power lines, fluorescent lighting fixtures, and sources

of noise such as radios, transmitters, and broadband amplifiers.

This product is not intended to be installed and used in a home or public area

accessible to the general population. When installed in schools, this equipment

must be installed in a secure location accessible only by trained personnel.

Mount in a location away from direct sunlight and sources of heat. A maximum

ambient temperature of 104º F (40º C) is recommended.

If installed in a closed or multi-rack assembly, the operating ambient temperature

of the rack environment may be greater than the room ambient. Therefore,

consideration should be given to installing the equipment in an environment

compatible with the maximum recommended ambient temperature.

Mount the Dell SonicWALL appliances evenly in the rack in order to prevent a

hazardous condition caused by uneven mechanical loading.

Lithium Battery Warning

The Lithium Battery used in the Dell SonicWALL Internet security appliance may

not be replaced by the user. The appliance must be returned to a Dell SonicWALL

authorized service center for replacement with the same or equivalent type

recommended by the manufacturer. If, for any reason, the battery or

Dell SonicWALL Internet security appliance must be disposed of, do so following

the battery manufacturer's instructions.

•

Cable Connections

All Ethernet and RS232 (Console) cables are designed for intra-building

connection to other equipment. Do not connect these ports directly to

communication wiring or other wiring that exits the building where the

Dell SonicWALL is located.

•

Four mounting screws, compatible with the rack design, must be used and hand-

tightened to ensure secure installation. Choose a mounting location where all

four mounting holes line up with those of the mounting bars of the 19-inch rack

mount cabinet.

•

A suitably rated and approved branch circuit breaker shall be provided as part of

the building installation. Follow local code when purchasing materials or

components.

Consideration must be given to the connection of the equipment to the supply

circuit. Appropriate consideration of equipment nameplate ratings must be used

when addressing this concern. Do not overload the circuit.

Safety and Regulatory Information

Download from Www.Somanuals.com. All Manuals Search And Download.

für die Verwendung in Ihrem Land oder Ihrer Region zugelassen ist und den

geforderten Normen entspricht.

Sicherheitsanweisungen

Für eine ordnungsgemäße Montage sollten die folgenden Hinweise beachtet

•

Vergewissern Sie sich, dass die Schrauben nach dem Austausch mit

entsprechendem Werkzeug fest angezogen werden.

werden:

•

Das Dell SonicWALL Modell ist für eine Montage in einem standardmäßigen 19-

Zoll-Rack konzipiert.

Vergewissern Sie sich, dass das Rack für dieses Gerät geeignet ist und

verwenden Sie das vom Rack-Hersteller empfohlene Montagezubehör.

Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit

geschützt ist.

Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die

Lüftungsschlitze an der Seite des Gehäuses frei sind. Hier ist ein

Belüftungsabstand von mindestens 26 mm einzuhalten.

Achtung—Lüfter Potentielle Gefahrenquelle

Lesen Sie vor dem Austausch der Lüftereinheit die Anleitung, die mit dem Gerät

geliefert wurde und befolgen Sie die Anweisungen.

•

Achten Sie darauf, das sich die Netzwerkkabel nicht in der unmittelbaren Nähe

von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern oder

Breitbandverstärkern befinden

Dieses Produkt ist nicht dafür entwickelt, um in Bereichen mit öffentlichem

Zugang betrieben zu werden. Wenn es in Schulen betrieben wird, stellen Sie

sicher, dass das Gerät in einem abgeschlossenen Raum installiert wird, der nur

von speziell ausgebildetem Personal betreten werden kann.

Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht

ausgesetzt ist und sich nicht in der Nähe von Wärmequellen befindet. Die

Umgebungstemperatur darf nicht mehr als 40 °C betragen.

Wenn das Gerät in einem geschlossenen 19"-Gehäuse oder mit mehreren

anderen Geräten eingesetzt ist, wird die Temperatur in der Gehäuse höher sein

als die Umgebungstemperatur. Achten Sie darauf, daß die

Umgebungstemperatur nicht mehr als 40° C beträgt.

Bringen Sie die Dell SonicWALL waagerecht im Rack an, um mögliche Gefahren

durch ungleiche mechanische Belastung zu vermeiden.

Verwenden Sie für eine sichere Montage vier passende Befestigungsschrauben,

und ziehen Sie diese mit der Hand an. Wählen Sie einen Ort im 19-Zoll-Rack, wo

alle vier Befestigungen der Montageschien verwendet werden.

Ein angemessen dimensionierter und geprüfte Sicherung, sollte Bestandteil der

Haus-Installation sein. Bitte folgen die den lokalen Richtlinien beim Einkauf von

Material oder Komponenten.

Prüfen Sie den Anschluss des Geräts an die Stromversorgung, damit der

Überstromschutz sowie die elektrische Leitung nicht von einer eventuellen

Überlastung der Stromversorgung beeinflusst werden. Prüfen Sie dabei

sorgfältig die Angaben auf dem Aufkleber des Geräts. Überlasten Sie nicht den

Stromkreis.

Hinweis zur Lithiumbatterie

Die in der Internet Security Appliance von Dell SonicWALL verwendete

Lithiumbatterie darf nicht vom Benutzer ausgetauscht werden. Zum Austauschen

der Batterie muss die Dell SonicWALL in ein von Dell SonicWALL autorisiertes

Service-Center gebracht werden. Dort wird die Batterie durch denselben oder

entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt. Beachten Sie

bei einer Entsorgung der Batterie oder der Dell SonicWALL Internet Security

Appliance die diesbezüglichen Anweisungen des Herstellers.

•

Kabelverbindungen

Alle Ethernet- und RS232-C-Kabel eignen sich für die Verbindung von Geräten in

Innenräumen. Schließen Sie an die Anschlüsse der Dell SonicWALL keine Kabel

an, die aus dem Gebäude in dem sich das Gerät befindet herausgeführt werden.

•

Eine sichere Erdung der Geräte im Rack muss gewährleistet sein. Insbesondere

muss auf nicht direkte Anschlüsse an Stromquellen geachtet werden wie z. B.

bei Verwendung von Mehrfachsteckdosen.

Das im Lieferumfang enthaltene bzw. die im Lieferumfang enthaltenen

Netzkabel sind nur für die Verwendung in bestimmten Ländern und Regionen

zugelassen. Überprüfen Sie bitte vor der Verwendung eines Netzkabels, ob es

Safety and Regulatory Information

Download from Www.Somanuals.com. All Manuals Search And Download.

安全說明

需要滿足以下條件以進行正確安裝：

•戴爾 SonicWALL 設備被設計成安裝在一個標準的 19 吋機架安

裝櫃。需要滿足以下條件以進行正確安裝：

•使用機架製造商推薦的裝載硬體，確認機架足夠裝置所需

•請確認裝置內不會滲入水分或過多的濕氣。

•裝置週邊請保持通風，特別是裝置通風口側。建議裝置與牆

壁間至少要有 1 英吋 (25.44 公釐 ) 的淨空。

•纜線的路徑應遠離電源線、日光燈，以及會產生雜訊的來源，

如無線電、發送器與寬頻放大器。

•必須留心裝置與電源電路的連接問題，電路過載對過電流保

護與電路電線的影響需降至最低。解決這個問題時，需正確考

慮裝置銘牌額定值。不要過載電路。

•必須維護可靠的機架裝載設備接地。必須特別留意電源供應

器連線，而不是直接連接到電源板之類的分支電路。

•隨附的電源線僅限於特定的國家或地區使用。使用前，請確

認電源線的額定值且已被認可在你的地區上使用。

•當安裝及後續接觸產品背面之後，必須用工具將指旋螺釘鎖

緊。

•本產品的設計目的不是安裝並使用於住家或一般大眾可接觸

到的公共區域。如果是安裝在學校，本設備只能安裝在受訓人

員能接觸到的安全位置。

風扇潛在危險警告

•架設位置需遠離陽光直射與熱源。建議周圍溫度最高溫不要

超過 104°F (40°C)。

•更換風扇部件前，請仔細閱讀，並遵循所提供的指示。

鋰電池警告

•如果是安裝於封閉式或多組機架配件，機架環境的周圍操作

溫度可能會高過室內周遭。因此，在與上述建議之最高周圍溫

度相容的環境中安裝設備時，應將此列入考量。

•將戴爾 SonicWALL 裝置平坦地裝設在機架中，如此才能避免

因不均勻的機械負荷造成危險狀況。

•必須使用四顆與機架設計相容的安裝螺釘，並用手鎖緊螺釘，

確定安裝牢固。選擇一個安裝位置，將四個裝載洞孔對齊 19

吋架設機櫃的安裝桿。

使用者不得自行更換戴爾 SonicWALL 網際網路安全性裝置中使

用的鋰電池。必須將戴爾 SonicWALL 送回戴爾 SonicWALL 授權

的服務中心，以更換相同的鋰電池或製造商推薦的同類型鋰電

池。若因任何原因必須丟棄電池或戴爾 SonicWALL 網際網路安

全性裝置，請嚴格遵守電池製造商的指示。

纜線連結

•應當提供一個合適額定值並且已被認可的分支電路斷路器作

為安裝該裝置的一部分。在購買材料或部件時，應遵循當地安

全代碼。

所有乙太網路與 RS232 ( 主控台 ) 線路都是為與其他裝置進行內

建連接所設計的。請不要將這些連接埠直接連接至通訊線路，

或其他連出戴爾 SonicWALL 所在建築的線路。

Safety and Regulatory Information

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC Part 15 Class A Notice

VCCI Statement

NOTE: This equipment was tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy. And if not installed and used in accordance with the

instruction manual, the device may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user is required to correct the interference at

his own expense.

この装置は、クラスＡ情報技術装置です。この装置を家庭環境

で使用すると電波妨害を引き起こすことがあります。この場合

には使用者が適切な対策を講ずるよう要求

されることがあります。　　　　　　

VCCI - A

Canadian Radio Frequency Emissions Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à toutes la norme NMB-003 du

Canada.

Caution: Modifying this equipment or using this equipment for purposes not shown

in this manual without the written consent of Dell, Inc. could void the user’s

authority to operate this equipment.

Declaration of Conformity

India RoHS Statement

A “Declaration of Conformity” in accordance with the directives and standards has

been made and is on file at Dell Inc. Products Europe BV, Limerick, Ireland.

This product complies with Restriction of Hazardous Substances (RoHS)

requirements as prescribed by E-Waste (Management & Handling) Rules, by the

Ministry of Environment & Forests, Government of India.

For further information, please see:

CISPR 22 (EN 55022) Class A

http://www.dell.com/regulatory_compliance

This product complies with CISPR 22 and EN 55022 Class A standards.

Warning: This is a class A product. In a domestic environment, this product may

cause radio interference in which case the user may be required to take adequate

measures.

BMSI Statement

警告使用者：

此為甲類資訊技術設備，於居住環境中使用時，可能會造成射

頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。

Safety and Regulatory Information

Download from Www.Somanuals.com. All Manuals Search And Download.

Regulatory Information for Korea

Warranty Information

Ministry of Information and Telecommunication

Certification Number MSIP-REM-SWL-0A5

All Dell SonicWALL appliances come with a 1-year Limited Hardware Warranty

which provides delivery of critical replacement parts for defective parts under

warranty. Visit the Warranty Information page details on your product’s warranty:

http://www.sonicwall.com/us/en/support/Services.html#tab=warranty

All products with country code “A” and “J” are made in the U.S.A.

All products with country code “C” or “D” are made in Taiwan R.O.C.

All certificates held by Secuwide, Corps.

A 급 기기 ( 업무용 정보통신기기 )

이 기기는 업무용으로 전자파적합등록을 한 기기이오니 판매자

또는 사용자는 이 점을 주의하시기 바라며, 만약 잘못 판매 또는

구입하였을 때에는 가정용으로 교환하시기 바랍니다 .

ANATEL Certification for Brazil

Under the copyright laws, this manual or the software described within, cannot be

copied, in whole or part, without the written consent of the manufacturer, except in

the normal use of the software to make a backup copy. The same proprietary and

original. This exception does not allow copies to be made for others, whether or not

sold, but all of the material purchased (with all backup copies) can be sold, given,

or loaned to another person. Under the law, copying includes translating into

another language or format.

Specifications and descriptions subject to change without notice.

Este produto está homologado pela Anatel, de acordo com os procedimentos

regulamentados pela Resolução nº 242/2000 e atende aos requisitos técnicos

aplicados.

Para maiores informações, consulte o site da ANATEL -

http://www.anatel.gov.br

Warranty Information

Download from Www.Somanuals.com. All Manuals Search And Download.

Sony Car Stereo System CDX C8850R User Manual
Sony Car Video System CDX91 User Manual
Sony Computer Drive MSAC US2 User Manual
Sony Network Card AC V100 B User Manual
Sony Universal Remote 6124 User Manual
Spalding Fitness Equipment M8554411 User Manual
Spark Tech Network Card WX 6615 User Manual
StarTechcom Computer Drive drw150sasbk User Manual
Sun Microsystems Welding System 6800 4810 4800 3800 User Manual
Sylvania MP3 Docking Station SIP297 User Manual