Sonance Stereo Amplifier 1230 User Manual

INSTALLATION INSTRUCTIONS

S O N A M P 1 2 3 0 O W N E R ' S M A N U A L

PROFESSIONAL MATRIX POWER A M P L I F I E R

PN.33-2159 6.01

17. Damage Requiring Service - The appliance should be

serviced by a qualified service personnel when:

IMPORTANT SAFETY INSTRUCTIONS

When using your Sonamp^®1230, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following:

A. The power-supply cord or the plug has been damaged

B. Objects have fallen, or liquid has been spilled into

the appliance

1. Read instructions – All the safety and operating instructions should be

read before the appliance is operated.

C. The appliance has been exposed to rain

D. The appliance does not appear to operate normally or

exhibits a marked change in performance

2. Retain instructions – The safety and operating instructions should be

retained for future reference.

E. The appliance has been dropped, or the

enclosure damaged

3. Heed warnings – adhere to all warnings and precautions listed on the

appliance and in the operating instructions.

18. Servicing - The user should not attempt to service the appliance beyond

that described in the operating instructions. All other servicing should be

referred to qualified service personnel.

4. Follow instructions – Follow all operating instructions.

5. Water and moisture – The appliance should never be used next to water;

for example, near a bathtub, kitchen sink, laundry tub, in a wet basement, or

near a swimming pool, etc.

19. Lifting – Do not attempt to lift the Sonamp® 1230 without

assistance. Improper lifting of this 35 lb. unit can cause personal injury.

6. Carts and stands – The appliance should be used only with a cart or

stand that is recommended by the manufacturer.

20. Power requirement – Do not connect the Sonamp® 1230 to the

accessory outlet of another component. A minimum 15 amp grounded wall

outlet is required.

7. An appliance and cart combination should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

21. Storms – To prevent damage to components, unplug all electronic

equipment during thunderstorms.

8. Caution: To prevent electric shock, do not use the Sonamp (polarized)

plug with an extension cord, receptacle, or other outlets unless the blades

can be fully inserted to prevent blade exposure.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

9.Ventilation – The appliance should be situated so that its location does

not interfere with its proper ventilation. For example, the appliance should

not be situated on a bed, sofa, register, or similar surface that may impede

the flow of air through the ventilation openings.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE

REFER SERVICING TO AUTHORIZED

SERVICE PERSONNEL.

10. Heat – The appliance should be situated away from heat sources such as

radiators, heat registers, stoves, or other appliances (including amplifiers)

that produce heat.

11. Power sources – The appliance should be connected to a power supply

only of the type described in the operating instructions or as marked on the

appliance.

The lighting flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product's enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

12. Grounding or polarization – Grounding or polarization are the precau-

tions that should be taken so that these attributes of an appliance are not

defeated.

13. Power-Cord Protection - Power supply cords should be

routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, conve-

nience receptacles, and the point where they exit from the appliance.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

14. Cleaning - The appliance should be cleaned only as recommended by

the manufacturer.

15. Non-Use Periods- The power cord of the appliance should be unplugged

from the outlet when left unused for a long period of time.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

16. Object and Liquid Entry - Care should be taken so that objects do not

fall and liquids are not spilled through the opening of the enclosure.

WARNING

MOVE WITH CARE

Download from Www.Somanuals.com. All Manuals Search And Download.

SONAMP 1230

•

POWER

ACTIVE

A.C. ON

1 2

3 4

5 6

7 8

9 10

11 12

PROTECTION

A. FRONT PANEL

1. POWER SWITCH

2. ACTIVE L.E.D.

3. POWER L.E.D.

10 9

4. FAULT INDICATORS

SONAMP^®1230

AUTO-ON

INPUT

AUTO-ON

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

–

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

TRIGGER

MODE

RIGHT

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

5-24V AC/DC

VOLUME

OUTPUT

FUSE

F 10A T 250V

Caution: For Continued Protection Against Fire Hazard Use Only Same Type And Rating Fuses. Disconnect Power Supply Before Changing Fuse. Do Not Expose This Unit To Rain Or Moisture. No User Servicable Parts Inside. See Operating Manual Before Using.

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil ire ou l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

AUX

BUS INPUT

–

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

BUS OUTPUT

LEFT

GROUND

LIFT

120V 60Hz

BRIDGED

8Ω Min.

OFF

–

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RIGHT

AUX

CHANNEL

1200VA

B. REAR PANEL

1. SPEAKER TERMINALS (12)

2. BRIDGING SWITCH (6)

3. INPUT LEVEL CONTROL (12)

4. SOURCE SELECTION SWITCH (12)

5. BUS LINE-IN JACKS (3)

6. DIRECT INPUT SOURCE JACK (12)

7. LINE-OUT JACKS (3)

8. TRIGGER SELECT SWITCH

9. AUTO-ON SENSITIVITY CONTROL

10. CONTROL VOLTAGE INPUT

11.CONTROL VOLTAGE OUTPUT

12. POWER FUSE RECEPTACLE

13. POWER CORD RECEPTACLE

Download from Www.Somanuals.com. All Manuals Search And Download.

MediaLinQ^™cable to assure optimum sound reproduction.

Small gauge or inferior quality wire will degrade imaging,

diminish bass reproduction, and add a generally congested

quality to music. Always check local building codes before

installing wire in walls or ceilings.

Power Trigger Controls

The Sonamp® 1230 may be automatically activated by an input

signal, low voltage trigger, or manual pushbutton. It also

provides a 12 volt DC output to trigger other components.

Auto-On Control

Wires may be terminated with banana plugs for convenience if

connections will be changed frequently. Any connector should

be gold plated to prevent oxidation, which degrades sound

quality. The binding posts on the Sonamp® 1230 also accept

twisted bare wire ends through the 45º opening in their center

shafts. Do not overtighten shafts. Tinning the bare copper wire

is recommended. As an option, use contact enhancer on mating

surfaces of connections to retard oxidation and enhance signal

flow. Do not strip more than 1/2”of the jacket from speaker wires.

To use the Auto-On feature, turn the main power switch ON and

slide the TRIGGER switch on the rear panel to the UP

position. Use the SENSITIVITY control to set the minimum

signal level that will activate the amplifier. In this mode, the

amplifier will automatically turn off after 8 minutes of no input

signal at any of the 12 channel inputs. The Auto-On mode dis-

ables the other two triggering modes.

Voltage Control

When the TRIGGER switch is set to EXTERNAL VOLTAGE

(the center position) and the main power switch (on the front

panel) is set to ON, the amplifier will be activated by the

presence of AC or DC voltage, from 5 to 24 volts, at the

INPUT connector. The EXTERNAL VOLTAGE mode disables

the other two triggering modes. (DO NOT CONNECT TO

120VAC LINE VOLTAGE)

Always provide sufficient slack in wires to avoid tension or

accidental disconnection. Always contain any excess wire to

prevent tripping hazards.

Source Connection

Always use quality high fidelity interconnect cables such as

Sonance Silver MediaLinQ OFC Interconnects. If source

components are more than 20 feet from the amplifier, use the

LS1 and LR1 balanced line-level sender and receiver to avoid

signal degradation (As shown in Figure 6).

Bypass

If the TRIGGER switch is set to BYPASS (the bottom position)

and the main power switch (on the front panel) is set to ON, the

amplifier will always be active. The BYPASS mode disables the

other two triggering modes.

Plug source components (receiver, preamp, page signal) to the

LINE IN bus inputs at the top center of the amplifier.

Plug dedicated sources (zone output, page signal, video game,

or electronic doorbell) into the DIR (direct) channel inputs if

desired.

Ground lift

The GROUND LIFT switch breaks ground loops that can occur

between source equipment and amplifiers. Set the GROUND

LIFT switch to OFF for most applications. When the Sonamp

1230 is to be used in an equipment rack, set the GROUND LIFT

switch in the ON position. This will isolate the audio circuitry

from the chassis. Thus, the chassis need not be isolated from

the equipment rack with insulator washers.

Plug downstream amplifiers to the non-buffered LINE OUT

bus outputs at the bottom center of the amplifier.

Source Settings

The fourplex DIP switches of the Sonamp® 1230 provides the

most flexible configuration options of any multichannel ampli-

fier. Settings are changed by moving the switches from (ON) to

(OFF):

Status LEDs

AC ON LED – This red LED indicates that the AC power line

cord is plugged into a live AC outlet. If the main AC line fuse

opens, this LED goes out. The main power switch setting does

not impact this LED.

Assign to master left channel source

Assign to master right channel source

Mono reproduction of source

L + R

AUX

DIR

ACTIVE LED – This green LED indicates that the amplifier

has been activated via one of the three methods described previously.

Assign to AUX channel source

Select dedicated channel input.

Note: It is possible to assign one or all switches as needed (L+R+AUX,

where AUX is the page input for a hallway or waiting room with paging.

PROTECTION LEDs – These amber LED’s light during a fault

condition, one LED for each pair of channels. If one of the

Sonamp 1230’s protection circuits is triggered, the LED will

turn on. If a channel pair encounters a short-circuit event or an

extremely low impedance, the respective LEDs will light (1&2,

3&4, 5&6, 7&8, 9&10, 11&12).All other channel pairs are unaf-

fected. If the heat sink temperature is exceeded because of poor

air circulation or high ambient temperature, a cutoff switch

attached to left and right channels will activate. Each bank

(1&2, 3&4, 5&6 or 7&8, 9&10, 11&12)of a Protect LEDs will

then light to signify a fault. If amplifiers are in Bridged mode,

the Protection Circuitry will sense a short circuit across both

positive speaker terminals and also positive to negative speak-

er terminal.

Volume Control

The individual channel volume controls are useful to

balance the desired sound levels for various zones, to balance

output from right and left channels to compensate for room

characteristics such as size and ceiling height.Also,by reducing

the Sonamp volume control settings, you compel the source

preamp or receiver volume control to operate in the middle

of its range. do not set the level controls higher than the

maximum level desired. Place tape over the VC hole to prevent

tampering.

Download from Www.Somanuals.com. All Manuals Search And Download.

Each time the amplifier is initially plugged in and the main

power switch is turned on, the protection LEDs will light for

approximately 3 seconds while amplifier circuitry is stabilizing.

This prevents spikes and thumps from getting to speakers. Any

time the protection circuits are triggered, turn the main power

switch off before troubleshooting for shorted output connections

or faults with source components.

well as a preset maximum volume level (using the 1230 volume

controls). This capability allows tailoring sound reproduction

to the size and use of each room.

If one room requires more power, a pair of high output

channels may be configured by bridging two pairs of channels.

Commercial Background Music System with Paging Capabilities

(Figure 2)

Bridging Channels

Bridging a pair of 30W channels to yield one 60W channel is a

simple operation of moving the toggle switch from the

NORMAL position to the BRIDGED position. This operation

subsequently disables the routing/switching function of the

channel directly below the bridged channel. This would apply

to even numbered channels (2,4,6,8,10,12). The dip switch

controls for the BRIDGED channel is directly related to the odd

numbered channels(1,3,5,7,9,11). The bridged channel would

then use both positive speaker binding post connections (red +

terminals) to connect to speakers. (8Ω speakers only) Do not use

double banana plugs for bridged connections.

Features

• 6 Room

• Common Music Source

• Two Zones with AUX Input for Paging Function

Adding a microphone preamplifier connected to the AUX

input provides the capability of mixing the stereo source

with paging. For maximum flexibility, each channel is

individually configurable to use or ignore the AUX input.

Use an AL1/S to mute the audio inputs during paging.

A great application for restaurants, nightclubs,offices,etc.

Note: If possible, adjust the microphone preamp volume level

slightly higher than the other input source.

INSTALLATION SAFETY

When installing the Sonamp 1230, basic safety precautions

should always be followed to reduce the risk of fire,

electric shock, and injury to persons, see the following:

Multiple Zone Music System (Figure 3)

Features

1. Read and understand all instructions.

• 5 Zones are fed from Main System

2. Follow all warnings and instructions in this manual and

marked on the product.

• 1 Zone is a Dedicated system with IR Control of Volume and Input Selections

Using the Sonance Navigator Harbor, a matrix preamplifier

capable of directing signals to multiple amplifier inputs, or

employing several discrete preamplifiers, the Sonamp 1230

may be configured to provide different program material to all,

or some zones. The main input can drive any channels not

individually connected to sources.

3. Any service or repair required must be performed by qualified

factory authorized personnel.

4. Do not install this product in a high humidity environment

or near water, for example a wet basement, wet bar, or

swimming pool.

Home Theater and Music System (Figure 4)

Features

5. Do not defeat the ground pin on the AC cord.

6. Disconnect the AC power to Sonamp® 1230 when wiring or

reconfiguring connections.

• 10 Channels Bridged to 5 channels for 60 watt per channel Theatre Output

• 2 Channels for Second Room Output on Receiver or Separate Input Source

A five channel surround sound system may be configured

from five channels. The five bridged channel configuration

leaves two channels available for stereo reproduction in

other zones.

INSTALLATION EXAMPLES

Diagrams of these examples follow later in this manual. The

following six system examples are only the beginning, with

some imagination, many other variations are possible.

In larger home theaters where high listening levels must be

supported, every channel pair may be bridged, creating six

60 watt channels to support speakers in the LCR (left, center,

right), surround, and subwoofer roles.

Basic Background Music System (Figure 1)

Features

• 6 Room

A surround sound receiver may be configured to provide

source signal to the Sonamp 1230 for one room, while

independently driving another set of surround speakers with its

internal amplifier.

• Common Music Source

• Passive Volume Control at each Zone

Perhaps the simplest configuration of the Sonamp 1230 uses a

single source preamplifier into six sets of stereo speakers, one

pair of speakers per room. The factory default rear panel DIP

switches and toggles are set for this application. This is a single

zone system. Note that each room may have a volume control as

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiple Source/Multiple Zone with Paging (Figure 5)

MAINTAINING YOUR SONAMP 1230

The Sonamp® 1230 does not require periodic maintenance and

has no user serviceable parts inside. Do not remove the top

cover as this will increase your risk of electric shock. To keep

the amplifier clean, use only a soft cloth and never use any

solvents or abrasives. Fingerprints may be removed with a soft

cloth moistened only with a few drops of water.

Features

• 1 Zone is HIGH POWER with Bridged Outputs and IR Control

• 2 Zones are STEREO with Volume Controls

• 4 Zones are MONO with Impedance Matching Volume Controls and Paging

• 1 Zone is STEREO with Volume Control and Paging

• AUX Input for KSU Paging in Selected Zones

SPECIFICATIONS

This configuration shows several rooms in stereo mode while

utilizing mono in selected areas. Note that certain areas receive

the paging signal. Due to its large size, the master bedroom

receives a bridged 4 channels providing 60 watts per channel .

All Channels Driven

Output Power, Stereo mode, RMS: 30 Watts per channel, 12 channels @8Ω

45 Watts per channel, 12 channels @4Ω

60 Watts per channel, 6 channels @8Ω bridged

Major Corporate System (Figure 6)

Features

IHF: Dynamic Power:

Dynamic Headroom:

49 Watts per channel, 12 channels @8Ω

78 Watts per channel,12 channels @4Ω

158 Watts per channel, 6 channels @8Ω bridged

+2.13dB, 12 channels @8Ω

• Automatic 2 source Main Music

• 8 Speakers on 2 Channels with Impedance Matching Volume Controls and

MONO Function

+2.38dB, 12 channels @4Ω

+4.15dB, 6 channels @8Ω bridged

• 4 Zone Keypad System

Total Harmonic Distortion:

0.1% 20Hz-20kHz @8Ω (30 WRMS)

0.25% 20Hz-20kHz @4Ω (45 WRMS)

THD @ 1kHz less than 0.01% with 8Ω (30 WRMS)

THD @ 1kHz less than 0.01% with 4Ω (45 WRMS)

• Executive Office controls with option to select from Main Source to Local

• AC Power Control of Main Music Sources

• Key Switch On/Off of Entire System, Auto-On Feature Defeated, 12v control

for AC Switching

I.M. Distortion (SMPTE 4:1) @8Ω: 0.01% @ 30 Watts

Signal to Noise Ratio:

Input Sensitivity:

-100dB below rated output (A-weighted)

• AUX Input for KSU Paging in Selected Areas

700 millivolt for 30 watts RMS @8Ω

Input Impedance:

Power Consumption:

20kΩ

A specialized installation that includes remote key switch turn

on and usage of multi-zone controllers for individual spaces

with keypad controls. Executive suite is specialized with

main/local source selection and control of entire system.

Restrooms, small vestibules, elevators, and large rooms

arranged in multiple seating areas are some examples of spaces

more appropriate to monaural music. Each of the Sonamp

1230’s 12 channels may be individually configured for monau-

ral reproduction if required to achieve smooth coverage of the

entire musical content of the source.

1440 Watts, maximum 4Ω full power

1400 Watts maximum @ 4 ohms, full power

6.5 Watts, standby

AC Fuse

15A AG

10A AG

3-space Rack Mount Faceplate

Optional Items

Dimensions:

1160--13/2/"4x"16x-35/4-"3x /148"" x 15-3/8"

(425mm x 146mm x 391mm)

(267mm x 425mm x 457mm)

38 lbs (17KG)

RMF Dimensions:

Shipping Weight:

19" x 5-1/4" x 15-3/8"

(483mm x 133mm x 391mm)

38 lbs (17kg)

A Basic Six Zone System (Figure 7)

Features

• 6 Rooms

• 3 Music Sources

• 3 Video Sources

• Sonance Navigator Master keypads at each zone

This diagram depicts a basic six zone install featuring a

Sonance Navigator Harbor with three audio and three video

inputs feeding a Sonamp 1230 amplifier with voltage turn on,

as well as feeding video to three TVs located in zones two, five

and six.Each of the six zones is controlled by a Sonance Navigator

Master keypad. The source components are controlled by the

Harbor’s Common IR outputs. When only a couple source com-

ponents are present,the 200VA switched power outlet can be used

to power up these devices. A voltage controlled power strip to

power up more source components is recommended to prevent

overloading of the switched AC outlet. The Control Output of

the Harbor should be used to control the power strip. (Do not

exceed the 100mA rating of the Control Output.)

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL ASSISTANCE

If you have any questions about the operation or installation of

your Sonance Sonamp 1230, please call our Technical

Assistance Department on any business day at:

WARRANTY COVERAGE (USA ONLY)

If, within one (1) year from the date shown on the bill of sale,

the unit fails due to a defect in workmanship or materials,

Sonance will, at its option and at no charge to purchaser, repair or

replace the components of such unit which proves to be defective.

• (800) 582-0772 or (949) 492-7777 from 9 a.m. to 5 p.m., PST

For this warranty to be effective, the bill of sale must show that

the unit was purchased from an authorized Sonance retailer.

This warranty shall apply exclusively to the original purchaser

and shall not apply to units purchased for industrial or

commercial use.

OBTAINING SERVICE

Should your product require repair or service, contact your

authorized Sonance retailer for help, or use the following

procedure:

Furthermore, this warranty shall not apply if:

1. Prior to calling, note the product model number, serial num-

ber, purchase date, and original retailer’s name and address.

1. Damage to the unit was caused by accident, abuse, or misuse;

2. The unit was opened, modified, or repaired by unauthorized

personnel; or

2. Contact our Technical Assistance Department at the

number(s) above and describe the problem. If required, a

Return Merchandise Authorization (RMA) number will be

issued. IMPORTANT: Do not return the unit to Sonance

without first obtaining an RMA number.

3. The unit was not used as outlined in the operating instructions.

Exclusions and Limitations

The warranty set forth above is in lieu of all other warranties,

express or implied, of merchantability, fitness for a particular

purpose, or otherwise. The warranty is limited to Sonance

products registered herein and specifically excludes any

damage to any associated equipment, which may result for any

reason from use with this product.

3. If you are directed to return the unit to Sonance for repair,

pack the unit in its original shipping cartons(inner & outer).

Replacement packaging can be obtained from Sonance for a

small charge.

4. Contact United Parcel Service, Federal Express, or RPS to

arrange prepaid (not collect) shipping. Do not use the United

States Postal Service. IMPORTANT: Freight collect shipments

will be refused.

Sonance shall, in no event, be liable for incidental or consequential

damages arising from any breach of this warranty or otherwise.

This warranty gives you specific legal rights, and you may have

other rights, which vary from state to state.

5. Write the Return Merchandise Authorization number on the

outside of the shipping carton.

6. For warranty work, please include a copy of the original bill

of sale inside the package.

Ship the packaged unit to:

Technical Assistance Department

Sonance

212 Avenida Fabricante

San Clemente, CA 92672-7531

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 1 Single Zone

Factory Default Settings for DIP Switches and toggle switches

of Channel Assignments

INPUT SOURCE

PHONO VIDEO2

VIDEO1

FIXED

TAPE OUTPUT

LEFT

RIGHT

ZONE

VC60RX

Volume Control

LEFT

RIGHT

ZONE

SONAMP^®1230

VC60RX

AUTO-ON

INPUT

AUTO-ON

LEFT

Volume Control

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

LEFT

TRIGGER

MODE

–

RIGHT

CH.

CH. 10

CH. 11

CH. 12

5-24V AC/DC

VOLUME

OUTPUT

FUSE

250V

10A

AUX

BUS INPUT

–

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

BUS OUTPUT

LEFT

GROUND

LIFT

120V 60Hz

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

OFF

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RIGHT

AUX

RIGHT

–

CHANNEL

1200VA

ZONE

VC60RX

Volume Control

LEFT

RIGHT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

VOLUME

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil å l ire ou å l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

DIRECT

INDICATED

SLIDE SWITCH

POSITION

DIP SWITCH

POSITION

LEFT

RIGHT

AUX

NORMAL

BRIDGED

(BRIDGED POSITION)

(ON POSITION)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 2 Single Zone plus Paging

MICROPHONE PREAMP

OUTPUT

INPUT SOURCE

FIXED

TAPE OUTPUT

PHONO VIDEO2

VIDEO1

LEFT

RIGHT

ZONE

LINE IN

+ AUX

LEFT

RIGHT

ZONE

LEFT

SONAMP^®1230

AUTO-ON

INPUT

AUTO-ON

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

TRIGGER

MODE

–

RIGHT

CH.

CH. 10

CH. 11

CH. 12

5-24V AC/DC

VOLUME

OUTPUT

FUSE

250V

10A

AUX

BUS INPUT

–

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

BUS OUTPUT

LEFT

GROUND

LIFT

RIGHT

120V 60Hz

BRIDGED

RIGHT

8Ω Min.

OFF

CAUTION

RISK OF ELECTRIC SHOCK

ZONE

DO NOT OPEN

ZONE

RIGHT

AUX

–

CHANNEL

1200VA

LEFT

LINE IN

+ AUX

RIGHT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

VOLUME

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil å l ire ou å l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

DIRECT

INDICATED

SLIDE SWITCH

POSITION

DIP SWITCH

POSITION

LEFT

RIGHT

AUX

NORMAL

BRIDGED

(BRIDGED POSITION)

(ON POSITION)

_{Download from Www.Somanuals.co}1_m0_{. All Manuals Search And Download.}

Figure 3 Multiple Zone

ZONE

INPUT SOURCE

AUX

PHONO VIDEO2

VIDEO1

LEFT

VARIABLE

LINE OUTPUT

LEFT

RIGHT

IR CONTROL

INPUT SOURCE

FIXED

PHONO VIDEO2

VIDEO1

TAPE OUTPUT

LEFT

RIGHT

LEFT

VC60RX

Volume Control

RIGHT

SONAMP^®1230

AUTO-ON

INPUT

AUTO-ON

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

ZONE

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

TRIGGER

MODE

–

RIGHT

CH.

CH. 10

CH. 11

CH. 12

VC60RX

5-24V AC/DC

Volume Control

VOLUME

OUTPUT

FUSE

250V

10A

LEFT

AUX

BUS INPUT

–

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

BUS OUTPUT

LEFT

GROUND

LIFT

120V 60Hz

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

OFF

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RIGHT

AUX

–

CHANNEL

1200VA

RIGHT

WALL MOUNT

IR Receiver

LEFT

VC60RX

Volume Control

RIGHT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

VOLUME

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil å l ire ou å l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

DIRECT

INDICATED

SLIDE SWITCH

POSITION

DIP SWITCH

POSITION

LEFT

RIGHT

AUX

NORMAL

BRIDGED

(BRIDGED POSITION)

(ON POSITION)

_{Download from Www.Somanuals.co}1_m1_{. All Manuals Search And Download.}

Figure 4 HomeTheater Surround / Stereo Zone

ZONE

VIDEO

INPUT SOURCE

AUX

PHONO VIDEO2

VIDEO1

LEFT

FIXED

TAPE OUTPUT

LEFT

RIGHT

DVD PLAYER

FRONT FRONT

LEFT RIGHT

REAR

LEFT

REAR CENTER

RIGHT

SUB

DOLBY DIGITAL^®DECODER

FRONT FRONT

REAR

LEFT

REAR CENTER

RIGHT

SUB

LEFT

RIGHT

THE SUB

POWERED SUBWOOFER

FRONT LEFT

CINEMA TWO.LCR

ZONE

33-1476

y s t e m o n e . l c r

33-1476

y s t e m o n e . l c r

FRONT RIGHT

SONAMP^®1230

AUTO-ON

INPUT

AUTO-ON

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

TRIGGER

MODE

VC60RX

–

RIGHT

Volume Control

CH.

CH. 10

CH. 11

CH. 12

CINEMA TWO.SUR

5-24V AC/DC

VOLUME

OUTPUT

FUSE

250V

10A

AUX

BUS INPUT

–

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

BUS OUTPUT

LEFT

GROUND

LIFT

ZONE

120V 60Hz

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

OFF

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RIGHT

AUX

–

CHANNEL

1200VA

REAR RIGHT

REAR LEFT

VC60RX

Volume Control

CINEMA TWO.LCR

DIRECT

LEFT

INDICATED

DIP SWITCH

POSITION

33-1476

y s t e m o n e . l c r

SLIDE SWITCH

POSITION

NORMAL

BRIDGED

RIGHT

AUX

(BRIDGED POSITION)

(ON POSITION)

CENTER

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

VOLUME

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil å l ire ou å l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

_{Download from Www.Somanuals.co}1_m2_{. All Manuals Search And Download.}

Figure 5 Multiple Amplifier / Home Theater/Multiple Zone+Paging

ZONE

HOUSE SYSTEM

FIXED OUT

1•2•3•4•5

INPUT SOURCE

AUX

PHONO VIDEO2

VIDEO1

LEFT

FIXED

TAPE OUTPUT

LEFT

RIGHT

ZONE

KSU TELEPHONE

PAGE

OUT

BEDROOM

VARIABLE OUT

INPUT SOURCE

VARIABLE

PRE OUTPUT

LEFT RIGHT

IR CONTROL

ZONE

VC60RX

ZONE

Volume Control

KITCHEN

M10R

+ PAGING

T4000

PAGING

FOYER

ZONE

VC30RX

Volume Control

SONAMP^®1230

ZONE

AUTO-ON

INPUT

AUTO-ON

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

EXTERNAL VOLTAGE

BYPASS

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

TRIGGER

MODE

–

RIGHT

CH.

CH. 10

CH. 11

CH. 12

5-24V AC/DC

VOLUME

OUTPUT

FUSE

250V

10A

M10R

AUX

BUS INPUT

–

VC30RX

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

12VDC

Volume Control

PAGING

HALL

ZONE

BUS OUTPUT

LEFT

GROUND

LIFT

120V 60Hz

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

BRIDGED

8Ω Min.

OFF

VC60SX

CAUTION

RISK OF ELECTRIC SHOCK

Volume Control

DINING

DO NOT OPEN

RIGHT

AUX

–

ROOM

T4000

CHANNEL

M10R

1200VA

ZONE

VC60RX

Volume Control

BATH

ZONE

M10R

VC60RX

Volume Control

VC60SX

Volume Control

CLOSET

FAMILY

ROOM

T4000

ZONE

D8001

FLAT

TREBLE

MID

TREBLE

MID

SEE OWNER'S MANUAL

FOR ADDITIONAL SETTINGS

SEE OWNER'S MANUAL

FOR ADDITIONAL SETTINGS

TREBLE

MID

TREBLE

MID

PN.33-0917

LIVE

DEAD

LIVE

DEAD

Ω

ROOM

Ω

ROOM

REDUCE VOLUME BEFORE ADJUSTING SWITCHES

MASTER

BEDROOM

DIRECT

LEFT

INDICATED

DIP SWITCH

POSITION

WALL MOUNT

IR Receiver

SLIDE SWITCH

POSITION

NORMAL

BRIDGED

RIGHT

AUX

(BRIDGED POSITION)

(ON POSITION)

Virtuoso

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

DIRECT

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

LEFT

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

RIGHT

AUX

CH. 5

CH. 6

CH. 11

CH. 12

CH. 1

CH. 2

CH. 3

CH. 4

CH. 7

CH. 8

CH. 9

CH. 10

VOLUME

Mise en garde: Afin d' éviter toute possibilité d' incendie, n´ utiliser que le même type de fusibles. Débrancher l´appareil avant de changer les fusibles. Ne pas exposer cet appareil å l ire ou å l´humidité. Ne pas ouvrir l´appareil. Lire attentivement la notice avant utilisation.

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

NORMAL

BRIDGED

_{Download from Www.Somanuals.co}1_m3_{. All Manuals Search And Download.}

Sennheiser Microphone MVF 30 User Manual
Sigma Digital Camera QUick Infrared Camera User Manual
Silvercrest Car Stereo System CDV 710 User Manual
SonicWALL Switch PoEInjector User Manual
Sony Cell Phone 1904 User Manual
Sony Personal Computer PCV RS710 User Manual
Speco Technologies DVR DVR 16 IP User Manual
Stamina Products Elliptical Trainer 55 1630 User Manual
Symbol Technologies Scanner P370 User Manual
Tanaka Trimmer TBC 300SDH User Manual