Socket Mobile Computer Monitor GFK0121E User Manual

GEFanuc Automation

Programmable Control Products

Genius

Hand-held Monitor

User’s Guide

GFK-0121E

June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

Related Publications

For more information, refer to these

publications:

Content of this Manual

Genius I/O System User’s Manual

Chapter 1. Introduction: Chapter 1

describes the Hand-held Monitor. This

chapter lists catalog numbers and

specifications. It also explains

compatibility between different versions

of the Hand-held Monitor and various

other products.

(GEK-90486–1). Reference manual for

system designers, programmers, and

others involved in integrating Genius I/ O

products in a PLC or host computer

environment. This book provides a

system overview, and describes the types

of systems that can be created using

Genius products. Datagrams, Global Data,

and data formats are defined.

Chapter 2. Hardware Setup: Chapter 2

gives instructions for powering the HHM,

changing its EPROM, and changing its

battery pack. It also describes how to

install the HHM on a panel, and how to

install a separate HHM connector on a

bus.

Genius Discreteand AnalogBlocks User’s

Manual (GEK-90486–2). Reference

manual for system designers, operators,

maintenance personnel, and others using

Genius discrete and analog I/ O blocks.

This book contains a detailed description,

specifications, installation instructions,

and configuration instructions for all

currently–available discrete and analog

blocks.

Chapter 3. Getting Started: Chapter 3

explains how turn on the Hand-held

Monitor, and how to set up its features for

your application. Chapter 3 also explains

how to test the Hand-held Monitor ’s

operation.

Series 90-70RemoteI/O Scanner User’s

Manual (GFK-0579). Reference manual

for the Remote I/ O Scanner, which

interfaces a drop containing Series 90-70

modules to a Genius bus. Any CPU

capable of controlling the bus can be used

as the host. This book describes the

Remote I/ O Scanner features,

Chapter 4. Device Configuration:

Overview: Chapter 4 gives basic

instructions for using the Hand-held

Monitor to configure Genius devices.

Chapter 5. Monitoring the Bus and its

Devices: Chapter 5 explains how to use the

Hand-held Monitor to display data and

status information from other devices on

the bus. It also explains how to clear faults,

switch a dual bus, execute Pulse Testing,

and display the bus scan time.

configuration, and operation.

Genius Bus Interface Unit and Field

ProcessorUser’s Manual (GFK-0825).

Reference manual for the Bus Interface

Unit and the Field Processor, which

interface a station containing Field

Control modules to a Genius bus. Any

CPU capable of controlling the bus can be

used as the host. This book describes the

features, configuration, and operation or a

Bus Interface Unit or Field Processor.

Chapter 6. Reading CPU Memory:

Chapter 6 explains how to use the HHM

to read the contents of specified memory

locations in CPUs on the bus.

Chapter 7. Error Messages: Chapter 7

defines messages that may be displayed

during HHM startup or operation, or

device configuration.

FieldControl I/O Modules User’s Manual

(GFK-0826). Reference manual for system

Index-3

GFK-0121

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

designers, operators, maintenance

personnel, and others using Field Control

I/ O modules. This book contains a

detailed description, specifications, and

installation instructions for all

describes the installation and operation of

the Bus Controller. It also contains the

programming information needed to

interface Genius I/ O devices to a Series

Five PLC.

currently–available I/ O modules.

Genius I/O PCIM User’s Manual

(GFK-0074). Reference manual for the

PCIM, which interfaces a Genius bus to a

suitable host computer. This book

describes the installation and operation of

the PCIM. It also contains the

programming information needed to

interface Genius I/ O devices to a host

computer.

Series 90 -70Bus ControllerUser’s

Manual (GFK-0398). Reference manual

for the Bus Controller, which interfaces a

Genius bus to a Series 90-70 PLC. This

book describes the installation and

operation of the Bus Controller. It also

contains the programming information

needed to interface Genius I/ O devices to

a Series 90-70 PLC.

Genius I/O Single-slot PCIM User’s

Manual (GFK-0881). Reference manual

for the Single-slot PCIM, which interfaces

a Genius bus to a suitable host computer.

This book describes the installation and

operation of the PCIM. It also contains the

programming information needed to

interface Genius I/ O devices to a host

computer.

Series 90 -30Bus ControllerUser’s

Manual (GFK-1034). Reference manual

for the Bus Controller, which interfaces a

Genius bus to a Series 90-30 PLC. This

book describes the installation and

operation of the Bus Controller. It also

contains the programming information

needed to interface Genius I/ O devices to

a Series 90-30 PLC.

We Welcome Your Comments

and Suggestions

At GE Fanuc automation, we strive to

produce quality technical documentation.

After you have used this manual, please

take a few moments to complete and

return the Reader ’s Comment Card

located on the next page.

SeriesSix

Bus ControllerUser’s

Manual (GFK-0171). Reference manual

for the Bus Controller, which interfaces a

Genius bus to a Series Six PLC. This book

describes the installation and operation of

the Bus Controller. It also contains the

programming information needed to

interface Genius I/ O devices to a Series Six

PLC.

Series Five

Bus ControllerUser’s

Manual (GFK-0248). Reference manual

for the Bus Controller, which interfaces a

Genius bus to a Series Five PLC. This book

Jeanne L. Grimsby

Senior Technical Writer

Hand-heldMonitorUser’s Guide – June 1994

Index-4

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Chapter 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1

Hand-held Monitor Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HHM Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2

1-4

1-5

HHM Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2

Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1

Power for the Hand-held Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing the PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Permanent Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing a Separate Hand-held Monitor Connector . . . . . . . . . . . . . . . . . . .

2-1

2-4

2-6

2-9

Chapter 3

Chapter 4

Chapter 5

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Device Configuration: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Monitoring the Bus and its Devices . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1

4-1

5-1

Monitor Block Display for Discrete I/ O and Input Blocks . . . . . . . . . . . .

Monitor Block Display for Discrete Relay Output Blocks . . . . . . . . . . . .

Monitor Block Display for Analog Blocks . . . . . . . . . . . . . . . . . . . . . . . . .

Monitor Block Display for RTD or Thermocouple Blocks . . . . . . . . . . . .

Monitor Block Display for a High-speed Counter Block . . . . . . . . . . . . .

Monitor Block Display for a PowerTRAC Block . . . . . . . . . . . . . . . . . . . .

5-4

5-5

5-6

5-7

Monitor/ Control Reference Display for a Discrete, Relay, or High-speed Counter

Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

Monitor/ Control Reference Display for an Analog, RTD, or Thermocouple Block

5-10

Monitor/ Control Reference Displays for a PowerTRAC Block . . . . . . . .

5-11

Chapter 6

Chapter 7

Reading CPU Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-1

Table of Contents

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Restarts for autonumbers that do not restart in each

chapter.

these restarts must be in the header frame of chapter 1.

a:ebx, l 1 resetA

Reminders for autonumbers that need to be restarted

manually (first instance will always be 4)

let_in level 1: A. B. C.

figure bi level 1, reset

table_big level 1, reset

chap_big level 1, reset1

app_big level 1, resetA

figure_ap level 1, reset

table_ap level 1, reset

figure level 1, reset

a:obx:l 1, resetA

a:bigbx level 1 resetA

a:ftr level 1 resetA

letter level 1:A.B.C.

num level 1: 1. 2. 3.

c:ebx, l 1 reset1

c:obx:l 1, reset1

num_in level 1: 1. 2. 3.

rom_in level 1: I. II. III.

c:bigbx level 1 reset1

c:ftr level 1 reset1

roman level 1: I. II. III.

table level 1, reset

steps level 1: 1. 2. 3.

Chapter 1 Introduction

The Hand-held Monitor (HHM) is a convenient operator

interface device that can be used to set up and monitor a Genius

I/ O and communications system.

mon

GENIUS

Hand Held Monitor

The HHM features:

cfg

GE Fanuc

An LCD display with four lines of 16 characters each.

Selectable display language: English, German, French, or

Italian.

A 20-key sealed-membrane keypad.

A keyswitch that can be used to restrict operator access to

certain functions, as selected for the application.

Operation from its battery pack, or by 115 volt AC

or 230 volt AC power.

Home

The Hand-held Monitor screen is the operator ’s

window to the Genius bus and all of its devices. It can

be used to display:

Clear

I/ O data for any device on the bus.

Diagnostics.

Off

–

Bus scan time.

Descriptions of all devices on the bus.

Global Data addresses.

Memory data from CPUs on the bus.

The Hand-held Monitor can also be used for device configuration, fault clearing, and forcing I/ O circuits

and dual bus selection. It can also be set up to prevent the use of any of these capabilities.

A key feature of the Hand-held Monitor is its ability to communicate with I/ O blocks and to force discrete

and analog I/ O, whether or not there is a PLC or computer connected to the bus. This greatly simplifies

system check-out prior to full-scale system operation.

1-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Hand-held Monitor Description

ModeSelect Keyswitch

mon

GENIUS

Hand Held Monitor

cfg

GE Fanuc

LCD Display

HHM Cable

F3 F4

Function Keys

Decimal Keys

Home

Clear

Off

–

OperationKeys

Connectionfor

Charger/Adapter

The HHM Keypad

The Hand-held Monitor keypad has three types of keys: function keys (F1 - F4), decimal

keys, and operation keys.

Function Keys: The four keys in the top row (F1, F2, F3, and F4) have functions that

change as the display changes.

The bottom line of the screen shows the current functions of these keys. For example:

nx t p r v a c t v b u s

Decimal Keys: The decimal keys are used to enter numbers and change sign.

Operation Keys: The four keys on the right side of the keypad are used to control HHM

operations:

clears HHM error messages,

clears Genius faults,

deletes HHM keypad entries.

Home

Clear

displays the Home menu.

Off

∆

displays the previous screen.

turns the HHM on or off.

GFK-0121E

1-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

The HHM Display

The Hand-held Monitor has a 4-line LCD screen. On a new Hand-held Monitor,

displays are in English. The display language can easily be changed to French, German,

or Italian. (Instructions for changing the display language are on page 3-5).

In addition to alphanumeric characters, the display uses the following special characters:

tri-stateinput.

Output with Feedback, or block with both inputs and outputs.

circuit is forced OFF.

circuit is forced ON.

relay block point is forced open.

relay block point is forced closed.

circuit controls a Bus Switching Module.

reference address or Device Number not yet assigned.

reference address is out of range for the presently-selected HHM host.

For a list of other HHM abbreviations and their meanings, select F3 (HELP) from the

HHM Utilities menu.

Keyswitch

The Hand-held Monitor ’s keyswitch can be used to restrict access to certain features of

the HHM.

With the key present, the switch can be placed in either “configure” (cfg) or “monitor ”

(mon) position.

cfg

with the switch in Configure position, all HHM functions are available. In this

mode, the Hand-held Monitor can be configured to determine which of its fea-

tures will be usable once the key is removed.

mon: with the keyswitch in Monitor position, the HHM can monitor bus and block

data. Additional HHM functions, such as clearing faults or configuring I/ O

blocks, can be used in Monitor mode only if the HHM has been set up to permit

their use.

The key must be present to move the switch from Monitor to Configure mode position;

it can only be removed in MON position. Two identical keys are supplied with each

Hand-held Monitor. The key should be removed if system security is a concern.

Accessories

The Hand-held Monitor comes with:

A sturdy removable leather case. The case has a rear tab with snap closure for

carrying the HHM on a belt. The handle can be pivoted back to stand the

Hand-held Monitor upright on a table.

A rechargeable battery pack.

A battery charger/ adapter with 8-ft cord.

Two keys for the mode-selection keyswitch.

A removable 5 ft (1.5 meter) coiled communications cable.

Chapter 1 Introduction

1-3

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

HHM Compatibility

The following table shows which Hand-held Monitor versions are compatible with

specificGeniusI/ O, Field Control, and related products.

Note that the functionality of an older Hand-held Monitor can be upgraded by replacing

its firmware PROM. (PROM installation instructions are in chapter 2).

Product

Type

Product

Catalog

Number

Requires this Hand-

held Monitor Ver-

sion (or later)

24/ 48VDCAnalog 4Input/ 2Outputblock

24/ 48VDCRTD 6 Input block

24/ 48VDCThermocouple 6Input block

24/ 48VDCCurrent-SourceAnalog4Input/ 2Outputblock

24/ 48VDCCurrent-Source Analog 6Output block

115VACAnalog 4Input/ 2Outputblock

115VAC/ 125VDCRTD 6 Input block

115VAC/ 125VDCThermocouple 6Input block

115VAC/ 125VDCCurrent-SourceAnalog4Input/ 2Outputblock

115VAC/ 125VDCCurrent-Source Analog 6Output block

24/ 48VDCSource16I/ Oblock

24/ 48VDCSink16I/ Oblock

24VDCSource16I/ O block

24VDCSink 16I/ O block

12/ 24VDCSource32I/ Oblock

5/ 12/ 24VDCSink32I/ Oblock

115VAC8I/ O block

115VAC 8I/ O Low Leakage block

115VAC 16 Input block

115VAC/ 10-30VDCHigh-SpeedCounterblock,v1.x

115VAC/ 10-30VDCHigh-SpeedCounterblock,v2.0

115/ 230VAC Relay Normally-closed 16 Output block

115/ 230VAC Relay Normally-open 16 Output block

115VAC/ 125VDC8I/ OIsolated BlockwithFailed Switch Diagnostic

115VAC/ 125VDC8I/ OIsolatedwithoutFailed Switch Diagnostic

115-230VAC/ 125VDCPowerTRAC block, v.2.2or earlier

115-230VAC/ 125VDCPowerTRAC block, v.2.3

IC660BBA020

IC660BBA021

IC660BBA023

IC660BBA024

IC660BBA025

IC660BBA100

IC660BBA101

IC660BBA103

IC660BBA104

IC660BBA105

IC660BBD020

IC660BBD021

IC660BBD022

IC660BBD023

IC660BBD024

IC660BBD025

IC660BBD100

IC660BBD101

IC660BBD110

IC660BBD120

IC660BBD120D

IC660BBR100

IC660BBR101

IC660BBS100

IC660BBS101

IC660BPM100

IC660BPM100C

any

IC660HHM501B(v2.0)

IC660HHM501D(v3.5)

IC660HHM501E(v3.7)

IC660HHM501G(v4.0)

any

IC660HHM501B(v2.0)

IC660HHM501D(v3.5)

IC660HHM501E(v3.7)

IC660HHM501G(v4.0)

any

IC660HHM501B(v2.0)

any

IC660HHM501B(v2.0)

IC660HHM501D(v3.5)

IC660HHM501G(v4.0)

IC660HHM501B(v2.0)

any

IC660HHM501D(v3.5)

IC660HHM501G(v4.0)

Series Five Genius Bus Controller

Series 90-70Genius Bus Controller

Series Six Genius Bus Controller with Diagnostics

Series Six Genius Bus Controller without Diagnostics

Series90-30GENIUSCommunicationsModule

GENIUSNetwork Interface(GENI)module

IBM PC Interface Module (PCIM)

IC655BEM510

IC697BEM731

IC660CBB902

IC660CBB903

IC693CMM301

IC660ELB905

IC660ELB906

IC660ELB910

IC660HHM501C(v3.0)

IC660HHM501F(v3.8)

any

IC660HHM501C(v3.0)

any

GENIUSNetwork Interface (GENI)module with inverted connector

Series90-70RemoteI/ O Scanner

IC697BEM733

IC660HHM501G(v4.0)

any

24/ 48VDCBusSwitchingModule(BSM)

115VAC/ 125VDCBusSwitchingModule(BSM)

IC660BSM021

IC660BSM115

Field Controlproducts(all)

IC670xxxxxx

IC660HHM501J(v4.6)

GFK-0121E

1-4

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

HHM Specifications

Operatingtemperature

0–60 C(32–140 F)

–40 to +70 C(–40 to 158 F)

5-95%(non-condensing)

1.3 lbs (0.6 Kg)

Storagetemperature

Humidity

Weight:

withoutcase

with case

1.8 lbs (0.8 Kg)

Size (HxWxD): withoutcase

with case

8.00” x” 3.75x” 1.25(cmx)

10.85” x4.30” x2.25”

Required AC power (for battery charger)

115/ 230VAC 15%, 47-63 Hz

(16-hour charging period for IC660BPM500B.

8-hour charging period for IC660BPM500A,now

discontinued.)

Fully chargedoperation

Displaycharacters

Keyboard

6 hours

4 lines each of 16 LCD (0.2” - 5 mm high)

20 sealed keys with tactile feedback

Features

PerformsGeniusI/ Oblockconfiguration,monitors

I/ O data on Geniusbus,displaysdiagnosticin-

formation.

Displaylanguage

Drop Test

English,German, French, or Italian

Survives drop from 4 feet (1.2 meters) to concrete

floor landing on any surface or corner without af-

fecting its operation.

DataRates

153.6Kbaud standard,153.5Kbaud extended,76.8

Kbaud,38.4Kbaud

Ordering Information

Description

Catalog Number

Hand-HeldMonitor (includes all items listed below)

Cablefrom HHM to I/ O Block

Battery Pack

IC660HHM501

IC660HHC005

IC660BPM500

IC660BCM501

Battery Charger

OptionalAccessories

External HHM Connector: A panel-mountable or DIN rail-mountable HHM connector

(catalog number 44A736310-001-R001) is available. It can be used to provide a

permanent HHM connection point on a Genius bus. See chapter 2 for a description.

230VAC Power Adapter: An optional 230VAC Power Adapter (IC660MCA512) can be

used to connect the Hand-held Monitor Charger to variety of 230 VAC power outlets by

means of a standard computer cable (not supplied). See chapter 2 for a description.

Extra HHM Keys: For applications requiring extra keys for the Hand-held Monitor, a

group of five sets can be ordered separately. The catalog number is IC660MKS511.

Chapter 1 Introduction

1-5

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2 Hardware Setup

Power for the Hand-held Monitor

The Hand-held Monitor can be operated using its built-in battery, or connected to either

115 volt or 230 volt AC power. A battery pack must always be installed to operate the HHM,

even when using AC power.

An optional 230VAC Power Adapter can be used to connect the Hand-held Monitor Charger

to variety of 230 VAC power outlets. See page 2-2 for more information.

Charging the Battery Pack for AC Operation

To operate the HHM using AC power, if the battery pack is new or has become fully

discharged by operating the HHM on battery power, it must be charged for at least 20

minutes. If it is necessary to restore temporary operation before charging is complete:

Plug the adapter cable into the HHM.

Wait 15 seconds and power up the HHM. It may be necessary to remove the battery pack

for 15 seconds, then reinstall it.

Note that continually using the Hand-held Monitor in AC mode for an extended period of

time causes the battery pack to deteriorate. After up to two years of AC operation of the

HHM, the battery pack may not be able to accept enough charge to operate the HHM

independently. However, it can still be used for AC operation.

Selecting 120 VAC or 230 VAC

Before plugging the adapter into AC power to operate or charge the Hand-held Monitor,

be sure the switch at the base of the adapter is correctly set to match the incoming

power (120 volts AC or 230 volts AC).

120V

position

120V

230V

position

The Hand-held Monitor will operate while the adapter is connected.

2-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the 230VAC Power Adapter

The optional 230VAC Power Adapter (IC660MCA512) can be used to connect the Hand-

held Monitor Charger to variety of 230 VAC power outlets by means of a standard com-

puter cable (not supplied).

The Adapter has a receptacle on the top for the Hand-held Monitor Charger and an IEC

320 receptacle on the side for the computer cable.

HHM Charger receptacle in

top of Adapter

IEC 320 receptacle in

side of Adapter

Instructions

1. Set the power selection switch on the Hand-held Monitor Charger to the 230V position.

120V

230V

position

2. Plug the Hand-held Monitor Charger into the top receptacle on the Power Adapter

unit.

3. Plug the computer cable into the IEC receptacle on side of the Power Adapter unit.

4. Connect the computer cable to a suitable 230VAC power source.

During normal operation, it is best to connect and disconnect the cable at the outlet, not

at the Adapter.

GFK-0121E

2-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Operation

The HHM’s battery pack provides up to 6 hours of operation. To maximize battery life,

allow the battery to discharge fully between charges. The battery should be allowed to

fully discharge once a month.

Low Battery Power

Low battery power may cause this message:

* * L O W B A T T E R Y * *

* * H H M H A L T E D * *

P l e a s e R e c h a r g e

Or the display may blank, or two black lines may appear briefly. Low battery power

suspends the current operation.

Charging the Battery Pack

When you receive a new Hand-held Monitor, its battery pack is not charged. Before

using a new battery pack to power the HHM for the first time, charge it by plugging the

adapter into a power source for 24 hours. After this initial charging, subsequent

rechanges will require only 16 hours.

Maintaining spare battery packs will allow the HHM to operate using one battery pack

while another is being charged.

If the battery pack won’t take a charge, it usually indicates a faulty battery pack, not a

faulty Hand-held Monitor. Try another battery pack. Replacement (uncharged) battery

packs are available.

If a battery pack is left uncharged for a long time, it may be necessary to remove the

battery pack from the HHM and charge it while removed for up to 15 minutes.

Replacing the Battery Pack

To replace the battery pack, use a Phillips screwdriver (size 0 or 1) to release the retaining

screw at the bottom of the HHM. Slide the battery pack out, insert another, and tighten

the screw.

Automatic Shutoff

To conserve power, the Hand-held Monitor automatically shuts off 10 minutes after the

last key is pressed. For applications where continual operation is preferred, the

automatic shutoff feature can be disabled. See page 3-5 for more information.

GFK-0121E

2-3

Chapter 2 Hardware Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Changingthe PROM

New features can be added to upgrade a Hand-held Monitor by replacing its PROM as

described below.

Caution

To prevent possible damage to the Hand-held Monitor, this operation should be

performed in an area equipped with suitable electrostatic discharge protection.

1. If the HHM is connected to AC power, disconnect it.

2. Remove the HHM battery pack as described on the previous page.

3. On the front of the Hand-held Monitor, remove the two Phillips-head screws located

near the 7 and HOME keys.

4. Gently raise the keyboard up from the bottom to release the lip between the

keyboard and the display.

5. Once this lip is free, open the keyboard to the right, as illustrated below. It is not

necessary to remove the ribbon connector.

mon

GENIUS

Hand Held Monitor

cfg

GE Fanuc

Install PROM

with notch to

right as shown

6. Remove the old PROM. If you don’t have a PROM extraction tool, a small screwdriv-

er can be used instead, carefully working from side to side.

GFK-0121E

2-4

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

7. If necessary, bend the pins on the PROM so they line up properly with the holes in

the socket. Bend the pins by pressing each side against a clean desk or table top as

shown below. If possible, a conductive mat should be used.

46024

Conductive mat

8. Insert the EPROM or Battery-Backed RAM into the socket.

IMPORTANT: Inserting the PROM backward can damage the Micro PLC and

destroy the PROM.

Newer PROMs may be physically longer, but all PROMs must be inserted flush with

the left edge of the socket, with the notch toward the ribbon connector.

9. Reposition the keyboard in its lip and tighten the two screws.

10. Reinstall the battery pack.

GFK-0121E

2-5

Chapter 2 Hardware Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Permanent Installation

If the Hand-held Monitor is to be installed using the metal bracket provided, follow the

instructions below. Do not install the HHM yet if it will be used to configure I/O blocks.

The mounting bracket provided can be used to install the Hand-held Monitor behind a

panel. You will need to make a cutout in the panel for the HHM (see next page).

You will also need to install a connector for the Hand-held Monitor within reach of the

HHM’s cable. The extra D-shell connector provided with the Hand-held Monitor

requires a panel cutout, with the bus cable and Hand-held Monitor located on the

opposite sides of the panel (see page 2-8).

An optional panel-mountable or DIN rail-mountable connector is also available. It does

not require a cutout. See page 2-9 for details.

Back of HHM

Bracket

Behind Panel

Optional HHM

Connector

Bus In

Bus Out

To Power Source

Configuringa Permanently-installed HHM

Ordinarily, a Hand-held Monitor installed on a panel serves as an operator station. Its

configuration may be different from that of a portable HHM.

Its Device Number must be changed from 0 to some other number.

Automatic shutoff may be disabled.

I/ O block configuration and other features may also be disabled.

After the HHM is configured, its keyswitch should be placed in MON position, and the

key removed.

GFK-0121E

2-6

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

HHM Installation Instructions

1. Select a suitable location for the HHM. Environmental specifications are listed on

page 1-5. The location must have 115 VAC or 230 VAC power.

2. Cut an opening 3.75 (9.53cm) wide x 8 (20.32cm) high in the panel. Drill four

mounting holes as shown below.

4.38in

(11.13cm)

3.75in

(9.53cm)

1.00in (2.54cm)

Cutout

6.00in

(15.24cm)

1.00in (2.54cm)

3. Attach the bracket to the HHM with the screws, washers, and lockwashers provided.

(4) holes for

mounting on

panel

(2) holes for mounting to

back of Hand-held Monitor

4. Using appropriate hardware (not provided), mount the HHM and bracket in the

cutout.

5. Connect the power cord to the HHM, and connect the signal cable to the connector.

GFK-0121E

2-7

Chapter 2 Hardware Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the D-Shell HHM Connector

Follow the instructions below if you are installing the supplied D-shell connector on the

bus.

1. Using the mounting plate as a template, cut an opening in the panel for the mating

connector. Also drill two holes for the mounting hardware.

2. Attach the mounting plate and mating connector to the panel using the mounting

hardware supplied.

3. Secure the two ends* of the serial bus cable to the back of the panel using strain

relief brackets.

4. Strip the ends of the wires. Twist the two Serial 1 wires together and attach them to

pin 5 of the connector. Twist the Serial 2 wires together and attach them to pin 9.

Similarly, attach the Shield wire(s)* to pin 4.

The following illustration shows connections for incoming and outgoing serial bus

cable. As with other devices, the HHM connector may be at either end of its bus. If it

is, there will only be one bus cable attached.

Bus

Cable

Strain

Reliefs

Bus

Cable

a42240c

Mounting

Hardware

Hand-held

Monitor

Connector

Mating

Connector

Mounting

Plate

Shield

(Pin 4)

SER 2

(Pin 9)

SER 1

(Pin 5)

Crimp

(Qty. 3)

MountingSurface

(rear view)

When making bus connections, the maximum exposed length of bare wires should

be two inches. For added protection, each shield drain wire should be insulated with

spaghetti tubing to prevent the Shield In and Shield Out wires from touching each

other.

If the HHM connector is at either end of its bus, it is necessary to install an

appropriate terminating resistor across the Serial 1 and Serial 2 wires. The Genius I/O

System and Communications User’s Manual lists appropriate terminating resistors for

each recommended bus cable type.

GFK-0121E

2-8

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing a Separate Hand-held Monitor Connector

You can add a connector to the bus for a permanently-mounted Hand-held Monitor, or

to provide an additional attachment point for a portable HHM.

The unit shown below (catalog number 44A736310-001-R001) provides a Hand-held

Monitor connector and serial bus terminals.

46357

.5 in

1.27 cm

1.673 in

4.249cm

Hand-held Monitor

Connector

Panel Mounting Ear

2.834 in

7.198 cm

X1 X2 SA SB

Serial Bus Terminals

Serial 1

Serial 2

X1 X2 SA SB

SA Shield In

SB Shield Out

shown at 100% of actual size

Mounting the HHM Connector

This unit can be easily mounted on a rail such as a standard 35mm (shown below) or

15mm DIN rail. The panel-mounting ears are not used if the unit is installed on a DIN

rail.

46358

35mm DIN rail

(Removable) DIN rail

Mounting Feet

side view: shown at 50% of actual size

Alternatively, it can be installed directly on a panel using screws through its mounting

ears. The DIN rail feet on the back of the unit are removed when the unit is

panel-mounted.

GFK-0121E

2-9

Chapter 2 Hardware Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Making the Bus Connections

The HHM connector has two sets of terminals; one for incoming cable and the other for

outgoing cable.

Connect the Serial 1, Serial 2, and Shield In terminal of either connector to the previous

device. Connect the Serial 1, Serial 2, and Shield Out terminal of the other connector to

the next device.

When making bus connections, the maximum exposed length of bare wires should be

two inches. For added protection, each shield drain wire should be insulated with

spaghetti tubing to prevent the Shield In and Shield Out wires from touching each other.

The following illustration shows connections for incoming and outgoing serial bus cable.

As with other devices, the HHM connector may be at either end of its bus. If it is, there

will only be one bus cable attached.

46366

Bus In

Bus Out

Serial 1

Serial 2

SA Shield In

SB Shield Out

As with other devices, if the HHM Connector is at either end of its bus, install an

appropriate terminating resistor across the Serial 1 and Serial 2 terminals. The Genius I/O

System and Communications User’s Manual lists appropriate terminating resistors for each

recommended bus cable type.

GFK-0121E

2-10

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3GettingStarted

This chapter explains how to:

Turn on the Hand-Held Monitor

Set the HHM Baud Rate

Display the Home Menu

Change the Hand-held Monitor ’s configuration:

the HHM Device Number

the HHM Display Language

the Host CPU

automatic shutoff

ability to Change Block ID Parameters

ability to Change the Baud Rate of Devices on the Bus

ability to Configure Devices on the Bus

ability to ForceI/ OCircuits

ability to Clear Faults

Test the operation of the Hand-held Monitor.

the Keypad

the Display Screen

the Internal Electronics

Display an alphabetical list of definitions for the definitions used on the HHM screen.

3-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning on the Hand-Held Monitor

With the battery pack charged, or with the HHM

connected to a suitable AC power source, press the

ON/ Offkey to turn the Hand-held Monitor on.

1. If the baud rates match, press F4 (Ok).

If the baud rates do not match, press F2

(Change) instead. The HHM screen changes to

allow you to select a different baud rate:

Caution

Do not connect or disconnect the

HHM to/from another device or con-

nector while it is ON.

H H M B A U D R A T E

A C T I V E = (baudrate)

P R O G

= (baudrate)

Connecting or disconnecting the

HHM while it is ON may disrupt

communications on the bus.

t g l e n t r

o k

A. With the key in CFG position, press F2

(Toggle). The selection changes to 76.8K,

38.4K, 153.6K extended, and back to 153.6K

standard.

Each time you turn on the Hand-held Monitor, it

executes a brief self-test.

G E N I U S H H M (version)

C O P R . (date)

B. When the correct baud rate appears on line

3, press F3 (Enter). Press F4 (Ok) to return

to the first baud rate screen.

G E F a n u c N . A .

S E L F T E S T W O R K I N G

2. Press F4 (Ok) to display the Home menu.

Powerup Error Messages

Chapter 7 lists error messages that may appear at

powerup.

Setting the HHM Baud Rate

Before the HHM completes the self-test, this

screen appears:

Sometimes, an error message appears although

the HHM has powered up normally.

POWERUP ERROR #4 or #5 may be caused by

excessive noise on the bus, or by an attempt to use

different baud rates on the same bus.

H H M B A U D R A T E

A C T I V E = 1 5 3 . 6 K S T

M U S T M A T C H B U S

c h n g

o k

It shows the baud rate that is currently set up for

the Hand-held Monitor. The baud rate

GFK-0121E

3-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying the Home Menu

This is the Hand-held Monitor ’s Home menu:

B. Pressing the Home key or DMenu key from a

lower-level screen.

F 1 : H H M U T I L I T I E S

F 2 : A N A L Y Z E

Use the Home menu to get to any other HHM

function, as shown below.

F 3 : C O N F I G U R A T I O N

F 4 : D E V I C E M E M O R Y

Notice that different screens appear, depending on

the type of device that is currently communicating

with the HHM.

Display the Home menu by either:

A. Pressing F4 (Ok) from the first baud rate

screen, or

F1: HHM UTILITIES

F2: ANALYZE

F3: CONFIGURATION

F4: DEVICE MEMORY

The Main HHM Screens

F1: HHM CONFIG

F2:SELF–TEST

F3: HELP

F1: MONITOR BLOCK

F2:MNTR/CTRL REF

F3: BLOCK/BUS STS

F4: PULSE TEST

F1: PROG BLOCK ID

F2: CONFIG BLOCK

F3: COPY CONFIG

DEVICE MEMORY #

(reference)

F1: MONITOR

F2: CONFIGURATION

tgl chng entr SBA

See chapter 6 for

instructions.

HHM CONFIG

BLOCK NO.

REFS

PROG BLOCK ID

I/O

BLOCK NO.

F1 Monitor I/O

F2:Faults

3 4 5 6 7 8 9 0

O O O O O O O

A 1 0 0 0 1 1 1

chng

nxt

ref blk

nxt

F3 Previous Menu

See page 3-4 for

instructions.

See page 5-4 for

instructions.

See page 4-4 for

instructions.

See page 5-15 for

instructions.

F1: KEYPAD TEST

F2: DISPLAY TEST

F3: TEST INTRNALS

F4:

MNTR/CNTL

STATE:

NO FAULTS

on off reles

F1: GENIUS CONFIG

F2: Module Config

(individualfeature

configuration

screens)

F3: Previous Menu

See page 3-7 for

instructions.

See page 5-9 for

instructions.

See GeniusI/O

BlocksManualor

individualblock

manual for

See page 4-7 for

instructions.

REFS

DC16K 15 v2.0ACT

FORCED, NO FAULTS

nxt prv actv bus

(help screens)

COPY CONFIG

FROM : TO :

See page 5-2 for

instructions.

chng

entr

See page 4-6 for

instructions.

PULSE TEST

REFS

NO FAULTS

exec

For Most

Genius Devices

For Field

Control

See page 5-17 for

instructions.

Chapter 3 Getting Started

3-3

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring the Hand-held Monitor

You can change the following operating

characteristics of the Hand-held Monitor:

Changing the HHM Device Number

The Device Number (serial bus address) assigned

to the Hand-held Monitor appears on line 2 of the

first HHM configuration screen.

PLC reference format.

153.6 Kbaud “standard” baud rate.

Device Number set to 0.

English language displays.

Shutdown after 10 minutes of inactivity.

I/ O block configuration enabled.

I/ O circuit forcing enabled.

Fault clearing enabled.

H H M C O N F I G

B L O C K N O .

c h n g

n x t

Each device on a Genius bus must have a unique

serial bus address number. A new HHM has

number 0. If multiple HHMs will be used on the

same bus, each of them must be assigned a

different Device Number.

Select F1 (HHM Utilities) from the Home menu to

access the HHM Utilities menu:

F 1 : H H M C O N F I G

F 2 : H H M S E L F T E S T

F 3 : H E L P

If you want to change the HHM Device Number,

follow these steps:

Press the ON key. Go to the Home menu. Se-

lect F1 (HHM Utilities), then F1 (HHM Config).

F 4

To change the configuration of the Hand-held

Monitor, select F1 (HHM Config) from the HHM

Utilities menu.

From the HHM Configure menu, press F2

(Change) to clear the existing Device Number.

Enter the new number and press F3 (Enter).

Pressing F4 from the buad rate screen will advance

you through additional HHM configuration

screens. Press Home if you want to return to the

Home menu, or use the DMenu key to go back to

the previous screen.

Note

The HHM key must be in the key-

switch, turned to CFG position.

After setting up the configuration, you can prevent

changes by turning the keyswitch to the MON

position and removing the key.

GFK-0121E

3-4

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Changingthe HHM Display Language

Enabling/Disabling Automatic Shutoff

The next display shows the current language

selection.

The next screen shows whether automatic shutoff

is selected.

H H M C O N F I G

L A N G U A G E

A U T O O F F = 1 O m i n

E N A B L E D

E N G L I S H

t g l e n t r n x t

Press F2 (TGL) to change the display language

(French, German, Italian, English). Press F3

(Enter) to save the change.

This feature conserves battery power by shutting

off the Hand-held Monitor 10 minutes after the

last key press. To change the current selection,

press F2 (Toggle), then F3 (Enter).

Selecting the Host CPU

Enabling/Disabling the Ability to Change Block

ID Parameters

The next display shows the Hand-held Monitor ’s

host CPU selection. The choices are: Series Six,

Series Five,PCIM/ QBIM/ GENI,orSeries90.

The next display shows whether the Hand-held

Monitor is able to configure the Block Number

(serial bus address) of bus devices, as well as the

I/ O circuit mix of some types of I/ O blocks.

S E L E C T H O S T C P U

S E R I E S S I X

C H N G B L K I D

E N A B L E D

To change the host CPU type, press the F2 (TGL)

key, then press F3 (Enter).

This selection also determines whether the HHM

is able to assign the Reference AddressofI/ O

blocks, or change the I/ O mapping of a Remote

I/ O Scanner (for the modules in its remote drop).

To enable or disable this capability, press F2 (TLG),

then F3 (Enter).

Chapter 3 Getting Started

3-5

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Enabling/Disabling the Ability to Change the

Baud Rate of Devices on the Bus

Enabling/Disabling the Ability to Force I/O

Circuits

The next configuration screen shows whether the

HHM is able to change the baud rate of bus

devices.

The next display shows whether the HHM can be

used to force I/ O circuits.

C I R C U I T F O R C I N G

E N A B L E D

C H N G B L K B A U D

E N A B L E D

To change the current selection, press F2 (Toggle),

then press F3 (enter).

To change the current selection, press F2 (Toggle),

then press F3 (Enter).

Enabling/Disabling the Ability to Clear Faults

Enabling/Disabling the Ability to Configure

Devices on the Bus

The next display shows whether the HHM can

clear faults on bus devices.

The next display shows whether the HHM is able

to change the other configurable features of bus

devices.

C L E A R B L K F A U L T S

E N A B L E D

C H N G B L K C O N F I G

E N A B L E D

To change the current selection, press F2 (Toggle)

then press F3 (Enter).

GFK-0121E

3-6

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing Operation of the Hand-held Monitor

If you want to test the Hand-held Monitor display,

Testing the Internal Electronics

keypad, or internal electronics, select F2 (HHM

SELF-TEST) from the HHM Utilities menu. This

menu of tests appears:

Press F3 (TEST INTRNALS) from the Self-Test

menu. After a moment, the HHM displays:

F 1 : K E Y P A D T E S T

F 2 : D I S P L A Y T E S T

F 3 : T E S T I N T R N A L S

F 4 :

T E S T I N T R N A L S

S E L F T E S T W O R K I N G

e x e c

Testing the Keypad

If an error occurs, one of the following messages

will appear instead.

Press F1 (KEYPAD TEST). The HHM prompts:

K E Y P A D T E S T

S T R I K E A N Y K E Y

K E Y =

E: P R O C E S S O R F A I L

E : R A M F A I L U R E

E : E P R O M F A I L U R E

E : E E P R O M F A I L U R E

E : C O M M E R R O R

M O N / C F G K E Y = C F G

Press any key you want to test. Each key press

is shown on the display. The HOME, D

MENU, and ON/ OFF keys are tested by their

operation.

Press the Clear key and try the test again. If the

message returns, replace the HHM. Otherwise,

continue.

To test keyswitch operation, turn the key and

observe the bottom line of the display.

An EEPROM failure will not prevent use of the

Hand-held Monitor. However, the HHM will not be

able to retain changes to its default configuration

through a power cycle.

Press D MENU to perform another test, or

press HOME to return to the Home menu.

The COMM ERROR message may indicate that

the Hand-held Monitor is not attached to a

correctly-terminated bus.

Testing the Display Screen

Press F2 (DISPLAY TEST) from the HHM Utilities

menu. The screen first displays uppercase letters

and special characters:

D I S P L A Y T E S T

A B C D E F G H I J K L M N O P

Q R S T U V W Z Y Z O 1 2 3 4 5

O I

6 7 8 9 : > ? – . / 1 O

I T

Next, a screen of lowercase letters appears,

followed by a continuous test pattern, which

checks pixel operation. When the test pattern is

finished, press DMENU to perform another HHM

test, or press HOME to return to the Home menu.

Chapter 3 Getting Started

3-7

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4Device Configuration Overview

The Hand-held Monitor can be used to configure (establish the operating characteristics for) a wide

variety of other devices. Some configurable devices are:

Genius I/ O Blocks, High-speed Counter Blocks, and PowerTRAC Blocks

the Series 90-70 Remote I/ O Scanner and its remote drop

Field Control stations.

The Hand-held Monitor displays a unique set of configuration screens for each type of configurable

device.

Because of the wide assortment of configuration features provided by the HHM, it has not been possible

to include them all here. You should refer to the more detailed configuration instructions in the User’s

Manual for the type of device you are configuring.

4-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Online or Offline Configuration

Devices can be configured before or after

installation on a properly-terminated serial bus. If

a new device is to be added to an existing bus

running at a baud rate other than 153.6 Kbaud

standard, the device must first be configured

offline. Be careful adding new devices to existing

systems. Be sure the baud rate configured for the

new device matches that of the system - never mix

baud rates on a bus.

Warnings

If the device is not properly grounded,

hazardous voltages may exist. Death or

injury may result.

DO NOT TOUCH the connectors or

wiring after powering up the device.

Hazardous voltages exist, and death or

injury may result.

OnlineConfiguration

When configuring a device on an operating bus,

the Hand-held Monitor must be the ONLY HHM

plugged into a device on the bus. If devices are

configured online, the HHM automatically check

for PLC reference address conflicts.

StartingConfiguration

Note: To assign a serial bus address, the

Hand-held Monitor must be directly attached to

the device being configured. Additional features

can be configured with the Hand-held Monitor

connected at any point on the bus. In that case, the

device being configured must be selected as the

active device (on the Block/ Bus Status screen).

OfflineConfiguration

It may be most convenient to configure devices

off-line at a central location. Each device will need

to be connected to an appropriate source of power

and to earth ground. To prepare a device for

off-line configuration:

1. Begin with the Hand-held Monitor turned off.

Attach the HHM to the device (see below) or

to another bus connection point.

1. Connect a 75 ohm resistor across the Serial 1

and Serial 2 terminals, or use the 75 ohm

terminator plug (IC660BLM508).

a42307

2. Attach a grounding strap to the device’s

ground screw. Be sure that the strap is

connected to earth ground.

a42468

Attach

Ground

Strap

Terminator

Plug

2. Turn the Hand-held Monitor on. After the

HHM completes its powerup sequence, the

Home menu appears. The Hand-held

Monitor’s Change Block Configuration option

must be enabled to complete the instructions

in this section. For a new device, the HHM’s

Change Block ID and Change Block Baud

options must also be enabled.

3. Wire the device to the power source and apply

power.

GFK-0121E

4-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying the Configuration Menus

The illustration below shows how to reach the

HHM’s device configuration menus from the Main

Menu.

the Configure Block screens to configure re-

dundancy and Configuration Protection.

For a Field Control device, select either F2

(Analyze) or F3 (Configuration) from the Main

Menu. The HHM will then display a special set

of screens for Field Control. (The currently-ac-

tive device must be the Field Control device for

these screens to appear. See page 4-7 if you

need instructions to select the active device).

For all devices, you will need to select F3 (Con-

figuration) then F1 (Program Block ID) to con-

figure a block’s required features.

Device Number (serial bus address).

I/ O typefor input/ outputblocks.

CPU references.

If the message E: CONFIG PROTECT appears,

you can remove Configuration Protection by:

Baud rate.

1. Going through the configuration screens to

reach the Configuration Protection screen.

For new blocks, this must be done first.

To configure Genius blocks, select F3 (Configu-

ration) from the Main Menu, then F2 (Config-

ure Block) to view and modify other features.

Detailed configuration instructions for each

type of device are provided in its User’s Manual.

2. Pressing F2 (Toggle) to select either DISABLED

or ENABLED.

3. Pressing F3 (Enter) to save the selection.

4. Pressing F4 (Next) to go to the first configura-

You can use F3 (Copy Configuration) to copy a

configuration from one block on the same bus

to another.

tion display, D MENU to return to the Configu-

ration menu, or HOME to return to the Home

menu.

To configure a remote drop, continue from the

Program Block ID screens to enter the remote

map (I/ O References) and Drop ID. Then go to

F 1 : H H M U T I L I T I E S

F 2 : A N A L Y Z E

F 3 : C O N F I G U R A T I O N

F 4 : D E V I C E M E M O R Y

Displaying the HHM

Configuration Menus

F2 or F3

F 1 : P R O G B L O C K I D

F 2 : C O N F I G B L O C K

F 3 : C O P Y C O N F I G

F 4 :

F 1 : M o n i t o r

F 2 : C o n f i g u r a t i o n

All Devices

P R O G B L O C K I D

I/O (devicereferences)

B L O C K N O . (device)

C O P Y C O N F I G

F R O M :

n T O :

r e f b l k

n x t

c h n g e n t r

Field Control

Devices

Configure a Remote

Map

Configure an

I/O Block

F 1 : G E N I U S C O N F I G

F 2 : M o d u l e C o n f i g

F 3 : P r e v i o u s M e n u

Remote I/O Scanner

Genius Blocks

and Remote I/O Scanner

GFK-0121E

4-3

Chapter 4 Device Configuration: Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

Completing the Program Block ID Screens

Select F1 (Program Block ID) from the

To Complete the Program Block ID Screen: The

Program Block ID screen is used to configure

additional features for some devices. These vary

from device to device; you should refer to the

device’s User’s Manual if you need more

information.

Configuration menu to complete the mandatory

part of a device’s configuration. (The HHM’s

CHNG BLK ID capability must be enabled).

When the HHM is set up for a PLC host, the

Program Block ID screen looks like this:

To Change the Device’s Baud Rate: press F4

(Next) from the Program Block ID screen. (The

HHM’s CHNG BLK BAUD capability must be

enabled).

P R O G B L O C K I D

I / O (devirceferences)

B L O C K N O . (device#)

S E L E C T B A U D R A T E

A C T I V E = 1 5 3 . 6 K S T

r e f b l k

n x t

P R O G

= 1 5 3 . 6 K S T

t g l e n t r n x t

If there are ? symbols on the screen, the

reference address and/ or Device Number have not

yet been configured. If there are * symbols on the

screen, a reference address was previously

assigned, but is out of range for the host CPU

currently set up for the HHM. If this happens,

check the host CPU setup in the HHM Utilities.

The bus will not operate unless all devices are set for the

same baud rate. Check the baud rate before

introducing blocks onto an operating bus.

To change the device’s baud rate, press F2

(Toggle), then press F3 (Enter).

When the HHM is set up for a PCIM/ QBIM/ GENI

host, references are not used. Instead, the second

line describes the device:

Cycle power to all devices on the bus at the

same time to use the new baud rate.

To Set the I/O Map for a Remote I/O Scanner:

The next screen is used to assign data types and

lengths for a Series 90-70 Remote I/ O Scanner. See

the next page.

P R O G B L O C K I D

I S O L 8 (device#)

B L O C K N O . (device#)

r e f b l k

n x t

To Enter or Change the Device Number: the

Hand-held Monitor must be connected directly to

the device.

1. Press F2 (blk). Then, enter the intended num-

ber (1-30). If you make a mistake, press F2

twice again, then enter the correct number.

2. Press the F3 (Enter) key. If the device is on-line

and the number has already been used, an er-

ror message appears.

GFK-0121E

4-4

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring a Remote I/O Scanner

After selecting the baud rate, the next Program

Block ID screen is used to assign data types and

lengths for a Series 90-70 Remote I/ O Scanner.

Configuringthe Remote Drop

To configure the remote drop with the HHM:

1. Enter a starting address and length for: %I (dis-

crete inputs), %Q (discrete outputs), %AI (ana-

log inputs), %AQ (analog outputs) on the

screen shown at left. The data lengths must

not add up to more than 128 bytes of inputs

and 128 bytes or outputs. If they do, an error

message will appear when you attempt to send

the data to the Remote I/ O Scanner.

P R O G R E M O T E M A P

% I

L E N G T H ( P T S )

t g l r e f s e n d n x t

Configuration Notes

2. Next, press F2 (drop) and enter a Remote Drop

ID (between 16 and 254).

The Remote I/O Scanner User’s Manual explains

remote drop configuration in detail. You should

use it as a reference during remote drop

configuration.

P R O G R E M O T E M A P

D R O P I D _____________

Also, look over the information below.Especially,

note that it is not always possible or desirable to

use a HHM for remote drop configuration.

t g l d r p s e n d n x t

If the remote drop includes any Analog Expan-

der Modules, Logicmaster 90 must be used for

configuration; do not use a HHM.

3. Press the F3 (send) key to download these

selections to the Remote I/ O Scanner.

Note: Do not perform this step if you want to

preserve a configuration entered using the Lo-

gicmaster software.

When a remote drop is configured with a

HHM, all I/ O modules will operate in default

mode; module options can only be configured with

the Logicmaster 90-70 software.

The HHM configures the I/ O references of Se-

ries 90-70 I/ O modules (only) in the remote

drop. It assigns references in ascending order,

starting with the slot next to the Remote I/ O

Scanner. The leftmost module of each type (%I,

%Q, %AI, or %AQ) in the rack receives the first

available reference of the appropriate type.

Unless the Remote I/ O Scanner is configuration

protected, pressing F3 (send) from the Remote

Map configuration screen causes the HHM to

automatically configure the remote drop. This

configuration will REPLACE any existingI/ O

configuration (including one entered using Lo-

gicmaster 90-70), and return I/ O module op-

tions to their original defaults.

4. Press F4 (nxt) to go to the Program Block ID

screen.

5. After completing these screens, press F2 (Con-

figure Block) to complete the Genius configura-

tion screens, or to display information about

the I/ O modules in the remote drop.

Remote drops configured with Logicmaster

90-70 are automatically protected. Please check

carefully before removing configuration protec-

tion with a Hand-held Monitor.

The module description screens that appear

during the configuration sequence are read-

only; boards cannot be configured here.

The Hand-held Monitor automatically creates a

configuration for a nine-slot rack, regardless of

the actual rack size. If the remote drop has a

five-slot rack, the HHM will later assume that

there are unfilled slots. If this is a problem, Lo-

gicmaster 90-70 can be used for configuration,

or to edit an automatic configuration done with

a Hand-held Monitor. Then, the configuration

can be stored to the Remote I/ O Scanner.

Go through these block description screens to

configure:

BSM Present

BSM Controller

CPU Redundancy

Configuration Protection

GFK-0121E

4-5

Chapter 4 Device Configuration: Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

ConfiguringGenius Blocks

To configure individual features of a Genius block,

the block must be the “active” device.

them all here. You should refer to the User’s

Manual for the device you are configuring for

descriptions of its configuration screens and

detailed instructions for completing them.

Selecting the Active Device

1. From the Analyze menu, select F3 (Block/ Bus

Status).

ConfigurationInstructions

1. To advance through the HHM configuration

displays making changes as needed, use the F4

(Nxt)key. You can pass through feature dis-

plays without making entries.

2. Press F1 (Next) or F2 (Previous), to reach the

device’s description screen.

3. When the desired device appears, press F3 (Ac-

tive) to make it the active device. (On a dual

bus, the HHM must be on the same bus as the

active block. If it is not, either move the HHM

or force the bus selection as described on

page 5-3).

2. To change a feature, use the TGL and CHNG

keys to select choices or enter other values. On

screens used to enter individual I/ O circuit op-

tions, use the F1 ( > ) key to choose a circuit,

then select the option using the TGL or CHNG

key. On some displays, you can enter new val-

ues from the keypad.

4. Press D MENU twice to return to the Main

Menu.

3. Press the F3 (Enter) key to save each change.

ConfiguringBlock Features

Select F3 (Configuration), then F2 (Config Block).

For Genius blocks, the HHM shows the first

configuration display. For example:

Copyinga Configuration

If there are similar devices on an operating bus,

you can use the Copy Configuration feature to

copy the configuration from one to the another.

Both of the devices must have a Device Number

already configured, and they must be operating at

the same baud rate. The device to be copied TO

must not be Configuration Protected.

P U L S E T E S T

R E F S (blocrkeferences)

E N A B L E D

t g l e n t r n x t

The device to be copied FROM must be the active

device (move the HHM to that block or select it

from the Block/ Bus Status screen).

The HHM shows the feature to be configured (in

the example above, it is the Pulse Test option). It

also shows the current status of that feature.

1. To begin, press F3 (Copy Configuration) from

the Configuration menu. The HHM shows:

When the Hand-held Monitor is set up for a PLC

host, line 2 shows the references assigned to the

device being configured. If there are ? symbols on

the screen, the device’s reference address has not

yet been configured. If there are * symbols on the

screen, a reference address was previously

assigned, but it is out of range for the host CPU

currently set up for the Hand-held Monitor. If this

happens, check the host CPU setup in the HHM

Utilities.

C O P Y C O N F I G

F R O M :

n T O :

c h n g e n t r

2. The Device Number of the active device ap-

pears next to the word FROM. Enter the De-

vice Number of the device being copied TO.

Press F3 (Enter).

When the HHM is set up for a PCIM/ QBIM/ GENI

host, line 2 shows the device type and Device

Number (serial bus address) instead.

3. Press the F4 (Execute) key. The configuration is

copied.

Because there are so many different device

configuration screens, it is not possible to show

GFK-0121E

4-6

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring Field Control Station

1. From the HHM Main Menu, display the special

1. If you want to change the address, enter the

new address using the keypad.

set of menus for Field Control.

A. If the Bus Interface Unit or Field Processor is

the current-selected device, press F2 (ana-

lyze) twice or F3 then F2.

2. Press F4 (entr). An error message appears if

the number has been used for another device.

Select a PLC Reference Address

B. If it is NOT the currently-selected device:

Select F2 (analyze) then F3 (Block/ Bus

Status).

If the host is not a Series Six PLC or Series Five

PLC, no entry is necessary here.

Press the F1 (nxt) or F2 (prev) key repeat-

edly to reach the serial bus address of the

BIU or Field Processor. Press F3 to make it

the active device. Then, press ∆Menu, fol-

lowed by F2 (Monitor/Control Ref).

If the host is a Series Six PLC or Series Five PLC,

assign an I/ O or register reference address.

S t a t T b l A d d r

O O O O O

F 1 : M o n i t o r

I O 6 e n t r

shows reference type

F 2 : C o n f i g u r a t i o n

1. Use the F3 key to toggle the selection of Series

SixI/ O memory, Series Five I/ O memory, or

User’s Manual for information about memory

usage in the Series Five and Series Six PLC).

From this menu, press F2 (Configuration). This

menu appears:

F 1 : G E N I U S C O N F I G

F 2 : M o d u l e C o n f i g

IfI/ O memory is used, the amount required is

equal to the number of bits of discrete data

PLUS analog data. Each analog reference used

consumes 16 points.

F 3 : P r e v i o u s M e n u

If register memory is used, an amount is re-

quired that is equal to the total number of bytes

of input data PLUS all of the output data

Press F1 to configure the BIU/ Field Processor.

Press F2 to configure individual modules.

2. Key in the number of the block’s beginning I/ O

or register reference. This may be:

Changethe Bus Address

SeriesSixI/ O

Series FiveI/ O

Registers

1 to 993

1 to 2041

1 to 16383

When you press F1 (Genius Configuration) from

the Configuration menu, the HHM shows the

serial bus address previously configured for the

BIU or Field Processor:

3. Press the F4 (Entr) key.

ConfigureAdditional Features

D e v i c e S B A

On the screens that follow, select these features:

Fault Reporting

Genius bus redundancy

BSM Controller

Output default time (for redundancy)

CPU redundancy

Duplex redundancy: default mode for outputs

Configuration protection

P r v >

e n t r

If the bus address is correct, press F2 to go on.

Note: If a BIU or Field Processor has a Serial Bus

Address conflict on an operating bus, it will not

scan the modules in the station until the fault is

cleared.

GFK-0121E

4-7

Chapter 4 Device Configuration: Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring Individual Field Control Modules

Go to the Field Control configuration menu:

Configure Data Addresses and Lengths

The next screens are used to assign the starting

addresses and lengths for I, then Q, then AI, then

AQ data.

F 1 : G E N I U S C O N F I G

F 2 : M o d u l e C o n f i g

If the host is a Series 90 PLC, these should

correspond to the memory assignments made for

the BIU or Field Processor during PLC configuration.

F 2 : P r e v i o u s M e n u

If the host is a Series Six or Series Five PLC, only

the length selected here is used; the entry made

on the starting address screen is not used by the

PLC. For those PLC types, the starting address was

assigned on an earlier screen.

From this menu, press F2 to configure the

individual modules in the station.

Disable the I/O Scan

1. For each data type, enter a starting address for

discrete input data (I). For example:

While you configure the modules in the station,

you may want to disable I/ O scanning. (The Bus

Interface Unit or Field Processor begins scanning

I/ O as soon as it is powered up).

B l k M a p S t a r t

I O O O O 1

I O S c a n

D I S A B L E D

e n t r

2. Press F4 to accept the value. Then, enter a

length in bits for I data. For example:

P r v

t g l e n t r

B l k M a p L n g t h

6 4

When the I/ O scan is disabled, previously

unconfigured module inputs and outputs default

to 0. For previously-configured modules, inputs

and outputs either default or hold their last state

or value, as configured.

e n t r

3. Press F4 (entr) to accept the value.

1. If you want to change the present selection,

press F3 (tgl).

4. Continue as above, entering starting addresses

and lengths for the other data types.

2. Press F4 (entr). If you want to go to the next

screen without changing the selection, press F2

( > ).

The lengths entered must not add up to more

than 128 bytes of inputs (discrete + analog)

and 128 bytes of outputs (discrete + analog).

5. Press F1 ( > ) after entering the length for AQ

data (the fourth data type).

If you changed any starting address or length

entries, the HHM displays this screen:

M a p h a s c h a n g e d

A c c e p t ?

n o y e s

6. To accept the changes and continue to the next

menu, press F4 (yes).

GFK-0121E

4-8

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

AddModules and Assign References

AssignI/O References for the Module

The first module configuration screen looks like this:

After you “accept” a module into the slot, a screen

like this appears:

Slot

number

Rack

number

R O : S 1

I 1 6

R O : S 1

E M P T Y

e n t r

t g l r e a d

Specify the I/ O references to be used by the

module. For most applications, you can simply

have the BIU/ Field Processor assign the next

available references in that memory type.

Use F1 and F2 to display

another slot (module)

The Rack Number is always 0.

A. To assign the next available references, just

press F4 (entr).

The Slot Number refers to the location of the

module relative to the BIU or Field Processor.

B. If you want to assign specific references, enter

the starting address. Press F4 (entr).

Read a Module Identification

Module references are automatically assigned by

the BIU or Field Processor based on its configured

data addresses and the number of points

appropriate for the module type.

If there is a module in the currently-selected slot,

pressing F4 (read) from the “empty slot” screen

brings up the module identification screen:

R O : S 1

D i s c r e t e O u t 1 6

M o d t y p e ?

Editing a Module Configuration

Module

type

To edit the module’s configuration, press F4 (zoom).

Refer to the module configuration instructions in the

BIU/Field Processor User’s Manual.

t g l e n t r

If you want to change the module type dis-

played, press F3 (tgl) to list other module types.

Delete an Existing Module Configuration

To delete the configuration of the module in the

present slot, press F3 (delete) then F4 (enter). Note

that this removes the entire module configuration.

To accept the module type, press F4 (entr).

Select a Module Type

If a module is not present in the selected slot, press

F3 (tgl) to select Generic I/ O or Special I/ O. Then

press F4 (entr).

ConfiguringModule Features

Configure additional module features as described in

the BIU/Field Processor User’s Manual. For example:

R O : S 1

G e n e r i c I / O

I / O t y p e ?

Change the module’s reference address.

Module Fault Reporting (discrete)

Default inputs (or outputs) or Hold Last State

(discrete and analog)

t g l e n t r

Channel Fault Reporting (analog)

Channel Active (analog)

Use the F3 (tgl) key again to go through the

module names.

When the correct module name appears, press

F4 (entr).

Input Current/ Voltage Ranges (analog)

Input or output scaling (analog)

Alarm thresholds (analog)

Output default values (analog)

GFK-0121E

4-9

Chapter 4 Device Configuration: Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5Monitoring the Bus and its Devices

This chapter explains how to perform monitoring and control operations with the Hand-held Monitor.

Displaying Information About Bus Devices (page 5-2).

Monitoringand ControllingIndividualCircuits on a

GeniusBlock (page 5-8).

Selecting the Active Device (page 5-2).

Clearing Faults (page 5-3).

Discrete, Relay, High-speed Counter Block (p. 5-9).

–

Forcing an Input or Output (page 5-9).

Display for a Bus Controller(page 5-3).

MonitoringtheBusStatus (page 5-3).

Switching a Dual Bus (page 5-3).

–

Clearing Circuit Faults (page 5-9).

Analog, RTD, or Thermocouple Block (page 5-10).

–

Forcing an Analog Value (page 5-10).

–

Clearing Circuit Faults (page 5-10).

MonitoringaGeniusBlock (page 5-4).

Discrete I/O and Input Blocks (page 5-4).

Discrete Relay Output Blocks (page 5-5).

Analog Blocks (page 5-5).

PowerTRAC Block (page 5-11).

–

Forcing PowerTRAC Data (page 5-12).

Diagnostics (page 5-12).

Monitoring/Controlling Remote Drop Data (page 5-13).

RTD or Thermocouple Blocks (page 5-5).

High-speed Counter Block (page 5-6).

PowerTRAC Block (page 5-7).

–

Forcing a Circuit (page 5-14).

Displaying and Clearing Faults (page 5-14).

Monitoring/Controlling Field Control Data (page 5-15).

–

Forcing/Unforcing the Reference (p 5-15).

Displaying and Clearing Faults (page 5-16).

Pulse Testing Outputs on Discrete Blocks (page 5-17).

F 1 : H H M U T I L I T I E S

F 2 : A N A L Y Z E

F 3 : C O N F I G U R A T I O N

F 4 : D E V I C E M E M O R Y

Monitoring and Operation

HHM Menus

F2 or F3

(FieldControl)

F 1 : M O N I T O R B L O C K

F 2 : M N T R / C N T L R E F

F 3 : B L O C K / B U S S T S

F 4 : P U L S E T E S T

F 1 : M o n i t o r

F 2 : C o n f i g u r a t i o n

F1 (Genius)

F4 (Genius)

F 1 : M o n i t o r I / O

F 2 : F a u l t s

REFS(blockreferences)

Pulse Test

discreteoutputs

F 3 : P r e v i o u s M e n u

F3 (All Devices)

F2 (Genius)

M N T R

I 2 :

4 4 1 – 4 6 4 A

– 1 9 3 7 0

N O F A U L T S

f o r c e

REFS (devicereferences)

Select the

ActiveDevice

here

D C 1 6 K 1 5 v 2 . 0 A C T

F O R C E D , N O F A U L T S

n x t p r v a c t v b u s

r e l e s

S E R I A L B U S S T A T S

A C T V D E V I C E S =

S C A N T I M E = 1 0 m s

5-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying Information About Bus Devices

Select F3 (Block/ Bus Status) from the Analyze

menu to:

Line 1 also provides information about the device

currently being displayed:

Display the references assigned to any device.

Display the revision level of any device.

Inputblock

Output block

Block with both inputs and outputs

Analog,RTD or Thermocoupleblock

PowerTRAC block or Remote I/ O Scanner

Display the description and Global Data ad-

dress of a bus controller.

Display the fault status of a Genius block or

Remote I/ O Scanner (remote drop).

Line 2 identifies the device and shows its serial bus

address (also called its Device Number or block

number), and its revision level.

Select the active device.

Clear all faults on the active device.

Access the Bus Status display.

Line 3 shows whether the device presently has

any forces or faults. If the device is a Field Control

BIU or Field Processor, however, the presence of

faults is not indicated on this screen.

This screen provides a quick way to check for faults

and forced circuits before starting up a system.

Block/BusStatus Displays for Bus Devices

Selecting Another Device

Example displays are shown below. (Display format

for bus controllers is shown on the next page).

Press F1 (Next) or F2 (Previous) as needed to

display information about other device.

Note: Poor bus conditions may cause the HHM to

skip (not display) a device that is present on the

bus. Try moving the HHM to a different

connector on the bus. Occasionally, this problem is

caused by certain older Genius blocks that do not

communicate with the HHM properly. If the

problem persists, such blocks can be upgraded.

Genius Block (discrete)

R E F S (devicereferences)

D C 1 6 K 1 5 v 2 . O A C T

F O R C E D , N O F A U L T S

n x t p r v a c t v b u s

Remote I/O Scanner

Selecting the Active Device

R E F S

R I O

* _

* G

1 5 v 3 . 5 A C T

Initially, the active device is the one to which the

HHM is connected.

N O F O R C E , F A U L T S

n x t p r v a c t v b u s

You can display information about other devices

without making them “active”.

BIU/Field Processor

However, for many functions the HHM must be

attached to another device or the other device must

be made “active” by following the steps below.

R E F S

* _

f l d p r 2 O v 1 . O A C T

N O F O R C E

1. From the Analyze menu, select F3 (Block/ Bus

Status).

n x t p r v a c t v b u s

2. Press F1 (Next) or F2 (Previous), to reach the

device’s description screen.

Line 1 shows the I/O references used by the device.

If * symbols appear instead of references, the

device’s references are incorrect for the type of host

CPU currently set up for the HHM. For example, if

a device is assigned to Series Six registers, and the

HHM is set up for a Series 90 host, the HHM will

display * symbols instead of references.

3. When the device’s screen appears, press F3

(Active) to make it the active device. (On a

dual bus, the HHM must be on the same bus as

the active block. If it is not, either move the

HHM or force the bus selection)

4. Press D MENU to return to the Analyze menu.

GFK-0121E

5-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitoring the Bus Status

Clearing Faults from the Block/Bus Status Screen

To display the number of devices currently operating

on the bus, and the current bus scan time, select F4

(Bus) from the Block/Bus Status display.

Pressing the CLEAR key from this screen clears

faults on the active device. For Genius blocks, if

you want to clear a specific circuit fault, select F2

(Monitor/ Control Reference) from the Analyze

menu instead.

S E R I A L B U S S T A T S

A C T V D E V I C E S =

Block/BusStatus Display for a Bus Controller

S C A N T I M E 1 O m s

If the active device is a bus controller, the Block/Bus

Status display shows information appropriate to that

bus controller type. For example:

The bus scan time shown is rounded down to the

nearest millisecond (10mS represents 10.01 to

10.99mS).

S E R I E S 6

BUS ADR:(device#)(vers)

REG (registers)

n x t p r v r / g b u s

Switching a Dual Bus

The first line identifies the bus controller type. If it

is a Series Five bus controller, PCIM, or QBIM, the

first line indicates:

To force a bus switch in a redundant bus system,

the HHM must be connected to the same bus as

the presently-active device.

1. If necessary, make the BSM Controller the ac-

tive device.

GE N I

A. From the Analyze menu, select F3 (Block/

Bus Status).

The second line of the display shows the bus

controller’s Device Number followed by its

firmware revision level.

B. Press F1 (Next) or F2 (Previous), to reach the

status screen for the BSM Controller.

C. When it appears, press F3 (Active) to make

the BSM Controller the active device.

Reading a Global Data Address

The third line of a bus controller ’sBlock/ BusStatus

screen shows its assigned Global Data address.

2. Press D MENU to return to the Analyze menu.

3. From the Analyze menu, select F2 (Monitor/

Control Reference). The HHM shows the ac-

tive bus and whether it is forced. For example:

If no Global Data address appears, it means that

either:

The bus controller has no Global Data address.

A Series 90-70 bus controller has a Global Data

address in %I, %Q, %AI, %AQ, or %R memory,

and no optional Series Six register address was

configured for the bus controller.

MNTR/CTRL (inputref)

S T A T E : B U S B F R C

> b u s A b i s B r e l s

If a Global Data address has been set up, you can

use the F3 (R/G) key to toggle between (R)egister

and (G)lobal memory format. If no Global Data

reference has been set up, the F3 key is not assigned.

4. Press F2 or F3 to select the other bus. The LED

on the BSM is off when bus A is selected and

on when bus B is selected. The I/ O Enabled

LED on each block on the active bus blinks.

Chapter 5 Monitoring the Bus and its Devices

5-3

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitoring a Genius Block

Select F2 (Monitor Block) from the Analyze menu to:

Monitor Block Display for Discrete I/O

and Input Blocks

Display the I/ O type of all circuits on the active

block.

For a discrete block, the Monitor Block display

shows the I/ O type and current state of each

circuit. This is an example display for an 8-circuit

grouped I/ O block:

Display (not change) forces on the active block.

Display the bus presently selected by the BSM

Controller.

Making the Block Active

REFS(blockreferences)

3 4 5 6 7 8 9

If the block is not presently selected as the “active”

block, follow the steps below.

B O

O O O

S I

I I I

A 1 O 1 1

O 1

1. From the Analyze menu, select F3 (Block/ Bus

Status).

2. Press F1 (Next) or F2 (Previous), to reach the

device’s description screen.

Line 1 indicates the block’s I/ O type:

Input

Output

Combination(I/ O)

3. When the block’s screen appears, press F3 (Ac-

tive) to make it the active device. (On a dual

bus, the HHM must be on the same bus as the

active block. If it is not, either move the HHM

or force the bus selection)

Line 2 shows the last digit of each circuit’s

reference address. The abbreviation on line 3

describes the I/ O type of each circuit:

4. Press D MENU to return to the Analyze menu.

Input

Tri–State input

Output

Output with feedback

Circuit that controls a BSM

After selecting the active device, use F1 (Monitor

Block) to monitor its data. This is a example

display for a discrete I/ O block:

Line 4 shows the current state of each circuit. This

information is updated continuously as the I/ O

states change.

REFS(blockreferences)

3 4 5 6 7 8 9

O 1

B O

O O O

S I

I I I

An underline means a circuit is forced (and does

not reflect actual circuit status):

A 1 O 1 1

OFF

forced OFF

Monitor Block screens for other types of Genius

blocks are described below.

forced ON

Block References

If the circuit is configured as a BSM controller, the

selected bus is displayed on line 4. If forced, the

active bus letter is underscored.

On all the Monitor Block screens for a Genius

blocks, line 1 shows the block references. If *

symbols appear instead, the references are out of

range for the CPU host currently setup for the

Hand-held Monitor. For example, if a block is

assigned to Series Six registers, and the HHM is set

up for a Series 90 host, the HHM displays

*symbols instead of references.

busA

forced to bus A

bus B

forced to bus B

Displaying Additional Circuits for a 32-circuit DC

block: Press a key from F1 to F4 to toggle the

display between circuits 1 to 16 and circuits 17 to 32.

If the HHM is set up for PCIM mode, references

are not used; a device description appears instead.

GFK-0121E

5-4

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor Block Display for Discrete Relay Monitor Block Display for RTD or

OutputBlocks

ThermocoupleBlocks

For a Relay block, the Monitor Block screen shows

the current open (O) or closed (C) states of all

relay outputs:

For an RTD or Thermocouple Input block, the

Monitor Block screen shows the current values of

two inputs at a time. Values reported by the block

may be tenths of degrees (Celsius or Fahrenheit),

tenths of ohms, or unconverted counts. This is an

example display showing tenths of degrees

Celsius:

R E F S (blockreferences)O

1 2 3 4 5 6 7 8 9 O 1 2 3 4 5 6

O O O O O O O O O O O O O O O O

O O O O C C O O O O O C O O C C

R E F S (circurietferences) A

I 1 :

I 2 :

1 5 O . O C

Line 2 shows the last digit of each circuit’s

reference address. The ‘O‘s on line 3 show that

each circuit is an output. Line 4 shows each relay

output’s present state. An underline means the

relay is forced.

2 5 . 5 C

Line 1 indicates that the block is an (A)nalog block.

Lines 2 and 3 display the input values. The

abbreviation FRC means a value is forced.

open

forced open

closed

Press F1 ( > ) to display the next pair of inputs.

forced closed

Monitor Block Display for Analog Blocks

For an analog block, each Monitor Block screen

shows the current value of two circuits at a time.

This is an example display:

R E F S (circurietferences) A

I 1 :

I 2 :

1 8 3 5 7

2 9 O 6 1

F R C

Line 1 indicates that the block is an (A)nalog block.

Lines 2 and 3 display the current values of two

circuits. On an analog block, each circuit may

report either unconverted analog data, or data

that has been scaled to be suitable for the

application.

The abbreviation FRC means a value is forced.

Press F1 ( > ) to display the next pair of circuits.

Chapter 5 Monitoring the Bus and its Devices

5-5

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor Block Display for a High-speed Counter Block

For a High-speed Counter block, the Monitor

Block function displays a sequence of screens with

the following information:

Control Inputs

Press F1 ( > ) to display the block’s Control Inputs:

1. The states of the block’s four Preset Outputs.

2. The states of the block’s Control Inputs.

C O N T R O L I N P U T S c

1 1 1 2 1 2 3

D H P P S S S

3. The current values of the block’s internal data

storage registers: Accumulator, Counts per

Timebase, and Strobe.

1 1 1 1 1 1

The exact appearance and sequence of screens

depends upon whether the block has been set up

for four-counter (Type A), two-counter (Type B), or

one-counter (Type C) operation. The letter a, b, or

c on the top line of the screen shows how the

block is set up.

On this screen, the numbers on line 2 identify the

first, second, third, of fourth control input of the

same input type on the block. The third line

identifies the input type: Disable Input (D), Home

Input (H), Preload Input(P), or Strobe Input (S).

The screen’s bottom line shows the current state of

each Control Input.

Preset Outputs

First, the Preset Outputs are displayed:

Press F1 ( > ) to display the current value in each

counter ’s accumulator, Counts-per-Timebase

R E F (ctrnumber)(ctrtype)

P R E S E T O U T P U T

R E F (number)(countertype)

A C C 1 : _ + (acc.value)

C T B 1 : _ + (countvalue)

Outputs that are forced are shown with an

underscore (forced outputs do NOT respond to

the actual value of the counter).

n x t

Use the F1 ( > ) key to display the strobe value(s),

and additional values appropriate to the counter

type. For more detailed instructions for using a

Hand-held Monitor with a High-speed Counter,

refer to the High-speed Counter User’s Manual.

GFK-0121E

5-6

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor Block Display for a PowerTRACBlock

If the active device is a PowerTRAC block, the

HHM’s Monitor Block function displays the

following screens:

Bit 15 = 1 means the overcurrent event indicated

by bit 4 occurred on the auxiliary current

line.

One screen showing the states of all of the

block’s Status Inputs.

Bit 16 = 1 indicates an internal calculation has re-

sulted in an out-of-range value. The block

should be reconfigured to prevent this.

Individual screens showing the block’s current

calculated data values. In the Monitor Block

function, these values are NOT labelled. It is

easier to display this information using the

Monitor/ Control Reference function (F2), be-

cause those displays are labelled.

Calculated Data

After the Status Inputs, the HHM displays the

block’s calculated data. If the PowerTRAC Block is

version 2.3 or later, this includes the additional

“low-priorityI/ O” data listed on page 5-11.

One screen showing the states of all of the

block’s Control Outputs.

On each of these screens, you can press F1 ( > ) to

display next screen, or press F2 (ref) and enter a

reference location to display a specific screen. For

a sequential list of the PowerTRAC block data, see

page 5-11.

REF (inputreference) I

1 1 7

> r e f

Status Inputs

Control Outputs

The Monitor Block function first displays the

PowerTRAC block’s Status Inputs:

After the calculated data screens, the HHM’s

Monitor Block function displays the PowerTRAC

block’s Control Outputs. You can also display this

data by using the F2 (ref) key to select output 1.

You may need to toggle (F2) the memory type.

R E F (inputreferences) I

1 2 3 4 5 6 7 8 9 O 1 2 3 4 5 6

O O O 1 1 O O O O O O 1 O O O O

> r e f

R E F (outputreferences) O

1 2 3 4 5 6 7 8 9 O 1 2 3 4 5 6

O O O O O O O O O O O O O O O O

> r e f

Line 2 indicates each of the 16 possible bit

locations for status data. Lin e3 shows the current

states of all inputs.

Bits 1 – 3 indicate the status of table data transfer,

for datagram communications.

Line 2 indicates each of the 16 possible bit

locations for Control Outputs. Line 3 shows the

current state of each Control Outputs. These

outputs are communications handshaking bits,

sent from the CPU to the block for certain

datagram communications. Information about

these outputs is in the PowerTRAC Block User’s

Manual.

Bit 4 = 1 indicates the block has captured an over-

current event.

Bit 5 should always be 1, indicating that the block’s

phase-lock loop is synchronized with the

incoming AC voltage.

Bit 12 = 1 means the overcurrent event indicated

by bit 4 occurred on phase A.

Bit 13 = 1 means the overcurrent event indicated

by bit 4 occurred on phase B.

Bit 14 = 1 means the overcurrent event indicated

by bit 4 occurred on phase C.

Chapter 5 Monitoring the Bus and its Devices

5-7

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitoring and Controlling Individual Circuits on a Genius Block

Select F3 (Monitor/ Control Reference) from the

Analyze menu to:

Basic Monitor/Control Display Format

Each Monitor/ Control Reference screen provides

information about one circuit, channel, or data

value. For example:

Display the present state or value of any circuit

on the active block.

Display the diagnostics status of any circuit.

Force and unforce individual circuits.

Force a bus switch on a dual bus.

Clear individual circuit faults.

M N T R

4 4 1 – 4 6 4 A

I 2 : – 1 9 3 7O

N O F A U L T S

> f o r c e

r e l e s

Making the Block Active

Line 1 shows the references used by that circuit. If

these are out of range for the host CPU set up for

the Hand-held Monitor, line 1 instead shows:

The block whose circuits will be monitored or

controlled must first be made “active” by following

the steps below.

1. From the Analyze menu, select F3 (Block/ Bus

Status).

MNTR (circuitnumber)+*A

2. Press F1 (Next) or F2 (Previous), to reach the

device’s description screen.

For example, the first circuit on the block appears

as: 1 + *

3. When the block’s screen appears, press F3 (Ac-

tive) to make it the active device. (On a dual

bus, the HHM must be on the same bus as the

active block. If it is not, either move the HHM

or force the bus selection)

If the HHM is set up for PCIM mode, references

are not used; a block description appears instead.

4. Press D MENU to return to the Analyze menu.

From the Analyze menu, press F2.

GFK-0121E

5-8

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor/Control Reference Display for a Discrete, Relay, or High-speed Counter Block

For a discrete, Relay, or High-speed Counter block,

Diagnostics

the Monitor/ Control Reference screen looks like

Line 3 of the Monitor/ Control Reference screen

this:

shows whether the circuit has any faults. If it

does, one of the following diagnostic messages

MNTR/CNTL(reference) I

S T A T E :

appears:

Failed switch: The commanded state of the circuit

does not match the actual state of the

switch or load.

N O F A U L T S

> o n o f f r e l e s

Loss of I/O power: One pair of circuits on an dis-

crete isolated block is not receiving power.

Line 1 identifies the circuit currently being

monitored. Pressing F1 ( > ) displays other

circuits.

No load: The load is drawing less than the block’s

minimum current level.

Open wire: An open wire condition has been de-

Line 2 shows the state of the circuit. In the

example above, the circuit is OFF and not forced

(no underline). Status is obtained directly from

the block for both inputs and outputs. If the

circuit is an output and no–load sensing is

enabled it reflects the current flow out of the I/ O

block to the load, as well as voltage at the field

terminals; otherwise, it indicates only the voltage

at the field terminals (output from the switch).

tected on a tristate input.

Overload: The output exceeds the block’s steady

state current limit.

Overtemperature: The block’s internal tempera-

ture exceeds 100 C.

Short circuit: Transient current above the block’s

short circuit limit.

Forcing an Input or Output

Clearing Circuit Faults

(The Hand-held Monitor ’s circuit forcing

After correcting a fault condition, press the CLEAR

key to remove the message and restore the

reference to normal operation (the Clear Block

Faults function must be enabled to use this

feature). If the fault condition still exists, the fault

message will reappear.

capability must be enabled to force or unforce a

circuit). To force a circuit on, press F2 (ON). To

force it off,press F3 (OFF). The force remains until

changed by the HHM (even through loss of block

power). To clear a force, press F4 (reles).

Chapter 5 Monitoring the Bus and its Devices

5-9

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor/Control Reference Display for an Analog, RTD, or Thermocouple Block

For an analog, RTD, or Thermocouple block, the

Monitor/ Control Reference screen shows the

current value for each circuit. For example:

Diagnostics

Line 3 shows whether the circuit has any faults. If

it does, one of these messages appears on line 3:

Feedback error: There is a wiring error or other

hardware fault on a Current-source Ana-

log block. The output’s actual current dif-

fers from the commanded current by

more than 250mA.

MNTR(ckt.reference) A

I 2 :

– 1 9 3 7O

N O F A U L T S

> f o r c e r e l e s

High alarm/low alarm: An analog input value ex-

ceeds its high or low alarm limit.

For an analog block, the values may represent

either engineering units or unscaled analog data.

Input shorted: An RTD input circuit measurement

is less than expected for the RTD type.

For an RTD or Thermocouple block, the values

represent tenths of degrees (Celsius or

Fahrenheit), tenths of ohms, or unconverted

counts.

Internal fault: Internal calibration readings for a

pair of RTD circuits are out of tolerance.

Open wire: On an RTD block, the RTD is missing

or faulty, or there is an open wire. On an

analog block, an input configured for 4 to

20mA has less than 2mA present.

Press F1 ( > ) to display other circuits.

Forcing an Analog, RTD, or Thermocouple

Value

Overrange/underrange: An analog or RTD circuit

exceeds its maximum value.

The HHM’s circuit forcing capability must be

enabled to perform this function.

Overtemperature: The block’s internal tempera-

ture exceeds 100 C.

1. Press F2 (Force) to force the displayed circuit.

Wiring error: There is a faulty connection be-

tween an RTD and the block.

2. If you make a mistake entering a value, use the

Clear key to delete one digit at a time, starting

with the last. To exit without forcing a circuit,

press F2 (Change).

Clearing Circuit Faults

After correcting a fault condition, press the CLEAR

key to remove the message and restore the

reference to normal operation (the Clear Block

Faults function must be enabled to use this

feature). If the fault condition still exists, the fault

message will reappear.

3. Press F3 (Enter) to save this value as the value

for the circuit. The forced value will remain

until you press F4 (reles), or enter a new value.

GFK-0121E

5-10

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitor/Control Reference Displays for a PowerTRACBlock

For a PowerTRAC block,the Monitor/ Control

Reference function displays:

For explanations of the data provided by a

PowerTRAC block, see the PowerTRAC Block User’s

Manual.

16 screens, each showing the state of one Status

Input. This information is more easily dis-

played with the Monitor Block function,which

shows all 16 Status Inputs on one screen. See

page 5-7.

Selecting a Memory Type or Address

To select a specific data item, you can enter its

memory type and/ or address. Press F2 (ref). This

screen appears:

Individual labelled displays of the block’s current

calculated data values. For PowerTRAC block

version 2.3 or later, this includes the “low-priority

I/O”screens described on the next page.

M N T R

16 screens, each showing the state of one of the

block’s Control Outputs. Control outputs are

also more easily displayed using Monitor Block.

t g l c h n g e n t r

PowerTRAC Data Sequence

1. Enter the reference number and press F3 (entr).

If the HHM is set up for a PLC host, I/ O refer-

ences increment by 16 and word(register) refer-

ences increment by 1. For a PLC host, both I/ O

and word references start at the first reference

assigned to the block. If the HHM is set up for

a PCIM/ QBIM/ GENI host, references begin at 1

and increment by 1.

The following table shows the sequence of

PowerTRAC block data that can be displayed on

the Monitor/ Control Reference screens:

Input

Word

Status inputs

(16screensin Monitor/ ControlReference)

Voltage phase A to B

2. The memory type blinks on the screen. To

change the memory type, use the F2 (tgl) key.

Voltage phase B to C

Voltage phase C to A

Voltage A to N (Line–to–neutral PTs only)

Voltage B to N (Line–to–neutral PTs only)

Voltage C to N (Line–to–neutral PTs only)

Current phase A

Current phase B

Current phase C

3. Press F3 (entr) to display the information.

Auxiliary CT current

Active power phase A

Active power phase B

Active power phase C

Reactive power A

Reactive power B

Reactive power C

Total power factor

Accumulated power

20 Fundamental VARsphaseA

21 Fundamental VARs phase B

22 Fundamental VARs phase C

23 Fundamental Power Factor, total

24 Harmonic VARS as % of V–A, phase A

25 Harmonic VARS as % of V–A, phase B

26 Harmonic VARS as % of V–A, phase C

27 Harmonic VARS as % of V–A, total

28 Line Frequency

29 TemperatureAlarm Status

30 Extended Watt-hour accumulator (upper 5 digits)

31 Extended Watt-hour accumulator (lower 3 digits)

32–64 not used

Control outputs

(16screensin Monitor/ ControlReference)

Output

Word 1

Chapter 5 Monitoring the Bus and its Devices

5-11

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

PowerTRACStatus Inputs Screens

PowerTRACControl Outputs Screens

First, the Hand-held Monitor displays 16 screens

showing the states of Status Inputs:

Finally, the HHM displays 16 screens showing the

states of individual Control Outputs (datagram

handshaking bits). If you use the F1 ( > ) key to

reach the Control Outputs, notice that there are

several unused references following the Extra

Calculated Data data. You can use F2 (ref) to go

directly to output 1. You may need to toggle the

memory type to %Q (or O, depending on the host

CPU setup of the HHM).

MNTR/CNTL(references)O

S T A T U S I N P U T S

S T S

> r e f f o r c e d i a g

To display additional data, press the F1 ( > ) key.

MNTR/CNTL(reference)O

C O N T R O L O U T P U T S

PowerTRAC Calculated Data Screens

S T S

After the Status Inputs, the HHM displays the

block’s calculated data values. Lines 2 and 3

identify the data being displayed and show its

present value. In the example below, voltage A to

N is 117 volts.

>r e f f o r c e d i a g

Forcing PowerTRAC Data

(The HHM’s circuit forcing capability must be

enabled to perform this function). Display the

data you want to force. Press F3 (force).

MNTR (inputreferences) 1

V a n

S T S

1 1 7

For bit data, the HHM displays:

> r e f f o r c e d i a g

mo n o n o f f r e l e s

PowerTRAC Extra Calculated Data (LPIO)

Screens

Press F2 (on) or F3 (off). To release the force, press

F3 (reles).

For word data, the HHM displays:

If the PowerTRAC block is version 2.3 or later, the

Hand-held Monitor next shows a series of screens

with extra calculated (“Low-PriorityI/ O”) data.

The block may or may not automatically provide

this data to the host, depending on the block’s

revision level and configuration. A CPU can use

datagrams to read the data.

S T S

f o r c e

r e l e a s e

Press F2 (force). The screen next displays:

L P I O

F U N D . V A R a

S T S – 2 7 O

> r e f

# 1 W

2 O I

FO R C E T O :

c h n g e n t r

d i a g

Press F2 (chng). Enter the force value, then press

F3 (entr). To release the force, press F4 (release).

On these screens, the top line shows the serial bus

address of the block and the relative data word

being displayed. For example, the screen above

shows the 20th input word (Fundamental VARs

for phase A). This area of line 1 blinks as a

reminder that the numbers shown are not

reference addresses.

Diagnostics

The PowerTRAC block does not report circuit

faults. If you use the F4 (diag) key from the

Monitor/ Control Reference screen, the message

NOFAULTSwill appear.

GFK-0121E

5-12

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitoring/Controlling Remote Drop Data

The HHM can display diagnostics and currentI/ O

states, and force and unforce individual I/ O points

on I/ O modules in a remote drop.

It shows the Remote Drop ID (143 in this

example), the rack number (0),the slot number (2),

and the memory type (%I). The number on the

righthand side of the second line represents a data

word.

When the active device is a Remote I/ O Scanner,

the HHM’s Monitor Block and Monitor/ Control

Reference functions display the same set of

screens. This is unlike HHM operation for Genius

blocks, where the screens for Monitor Block and

Monitor/ Control Reference are different.

14 3 # 4 . 2 % I

Startingreference

(groups of 16)

ReferenceType

SlotNumber

For the Remote I/ O Scanner, the monitoring

screens provide the following information:

Rack Number

1. The states of the discrete inputs in the remote

drop, in ascending order.

Remote ID Number

2. The values of the analog inputs in the remote

drop, in ascending order.

The Series 90-70 I/ O reference for the circuit is one

less than the sum of the two numbers on the

righthand side of the HHM screen. For example:

3. The states of the discrete outputs for the re-

mote drop, in ascending order.

4. The values of the analog outputs for the re-

mote drop, in ascending order.

M N T R

1 4 3 # 4 . 3 % I

3 3

On each screen, line 3 shows the state or value of

one circuit at a time. It also indicates whether the

circuit is forced, or has a fault as illustrated below.

The first screen that appears is the Monitor screen

for the module with the first %I reference.

3 + 33 – 1=35

In this example, the circuit being monitored is

%I0035.

Displaying Other Circuits

M N T R

1 4 3 # O . 2 % I

To display additional circuits, press the F1 ( > ) key.

The HHM will step through each available circuit.

To jump directly to a particular device, memory

type, or address, press F2 (ref). This screen

S T S

F A U L T

> r e f f o r c e d i a g

appears, to enter the desired information.

Line 1 shows the relative number in the word of

the circuit being monitored:

M N T R

t g l c h n g e n t r

Here, it is the first circuit on the block. The second

line identifies the I/ O module being monitored:

1. Enter the reference number. Press F3 (entr).

The memory type blinks on the screen.

2. If you want to select a different reference type

(for example, to display%AQ instead of %I),

press F2 (chng) to toggle the memory type.

1 4 3 # 4 . 2 % I

3. With the desired information displayed, press

F3 (entr) to monitor the circuit.

Chapter 5 Monitoring the Bus and its Devices

5-13

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Forcing a Circuit

Displaying and Clearing Remote Drop Faults

(The HHM’s circuit forcing capability must be

enabled to perform this function). Display the

circuit you want to force. Press F3 (force).

To display diagnostics for a circuit, press F4 (diag)

from the Monitor screen. If there is a fault, it

appears on line 3. For example:

For a discrete circuit, the HHM displays:

D I A G

mo n o n o f f r e l e s

1 4 3 # O . 3 % I

O V E R C U R R E N T

m o n

3 3

Press F2 (on) or F3 (off) to force the circuit. The

forced state appears on line 3. To release the force,

press F3 (reles).

n x t

If there is no fault on the circuit you are

For an analog circuit, the HHM displays:

monitoring, the Hand-held Monitor searches the

Remote I/ O Scanner ’s internal fault table to see

whether there are any faults on the remote drop.

If there are any uncleared faults on the remote

drop, the HHM displays the fault that occurred

first (the oldest fault). For example:

ST S 4

f o r c e

r e l e a s e

Press F2 (force) to force the circuit. The screen

next displays:

D I A G

FO R C E T O :

1 4 3 # O . 2 % A I

U N D E R R A N G E

m o n

n x t

Press F2 (chng). Enter the force value, then press

F3 (entr). The forced value will appear on line 3.

The HHM identifies the location where the fault

occurred (on line 2). From this screen, you can

display additional faults on the remote drop by

pressing F4 (nxt). Faults will appear in the same

sequence in which they occurred. For example,if the

fourth oldest is being shown, pressing F4 (nxt)

displays the fifth oldest, and so on.

FR C 1

> r e f f o r c e d i a g

To release the force, press F4 (release) from the

force/ releasescreen.

To return to the Monitor screen you started from,

press F1 (mon).

Clearing Faults

After correcting fault–causing conditions, you can

return to the Block/ Bus Status menu to clear all

fault messages for the remote drop. (The Clear

Block Faults function must be enabled to use this

feature).

GFK-0121E

5-14

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Monitoring/Controlling Field Control Data

The HHM can display diagnostics and currentI/ O

states, and force and unforce individual I/ O points

on Field Control modules.

Displaying Another Reference

Use the F2 ( > ) key to advance through the point

reference screens for the selected reference type.

1. From the HHM Main Menu, display the Field

Control main menu.

Changingthe Display Mode

The letter in the upper right corner of the display

shows the present data type:

F 1 : M o n i t o r

F 2 : C o n f i g u r a t i o n

binary

hex

decimal

Use the F4 (mode) key if you want to change the

display data type.

A. If the BIU or Field Processor is the active de-

vice, press either F3 (Configuration) or F2

(analyze) twice.

Returning to the Previous Menu

B. If it is NOT the active device select F2 (ana-

lyze) then F3 (Block/ Bus Status).

Press the HHM Clear key when you want to

return to the main Field Control menu.

Press the F1 (nxt) or F2 (prev) key re-

peatedly to reach the serial bus address

oftheBIU/ Field Processor. Press F3 to

make it the active device.

Forcing/Unforcing the Displayed Reference

I/ O points can be forced and unforced from the

Hand-held Monitor (the HHM’s circuit forcing

capability must be enabled to use this function).

Forcing an I/ O point changes its state in the Field

Processor’s EEPROM memory. If the circuit is an

output, the physical state of the output also

changes. If the circuit is an input, the forced input

data is sent to the CPU. A circuit retains its forced

state or value if power is removed. The forced

circuit ignores data from an attached input device,

or output data from the CPU. The force can

ONLY be removed from the Hand-held Monitor.

Then, press ∆Menu, followed by F2

(Monitor/ ControlRef).

2. Press F1 (Monitor). This menu appears:

F 1 : M o n i t o r I / O

F 2 : F a u l t s

F 3 : P r e v i o u s M e n u

3. Select F1 (monitor I/ O) to display the Monitor

screen for the first %I reference.

1. If the display is set to hex (H) or binary (B),

change it to decimal (D) by pressing F4.

Indicates force is in effect

Reference

2. Press the F3 (force) key to force the reference

now being displayed.

Current

being

state or value

monitored

I O O O O 1 * O

I O O O O 1 * 1

> f r c h e x

f r c u n f r c

3. Press F3 (force) again. Then, enter the forced

state or value. The HHM displays an asterisk to

indicate the state of value now shown is forced.

See the illustration at left.

Changingthe Reference Type Being Displayed

Use the F1 ( < ) key to select a reference type: I

(discrete inputs), Q (discrete outputs), AQ (analog

outputs), or AI (analog inputs).

4. Use the F4 (unforce) key from the same screen

when you want to unforce the point.

Chapter 5 Monitoring the Bus and its Devices

5-15

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Press F1 to display the first set of 16 faults (one

fault at a time). For example:

Displaying Field Control Faults

A Hand-held Monitor can display faults from a

Bus Interface Unit or Field Processor while

attached anywhere on the Genius bus.

S l o t # 1 F a u l t # 1

E X T R A I / O M O D U L E

1. From the HHM Main Menu, display the Field

Control main menu (instructions are on the

previous page).

e x i t

F 1 : M o n i t o r

A. Use F1 and F2 to display another fault

F 2 : C o n f i g u r a t i o n

B. If there are no faults, the HHM displays the

message: NoFaults on the top line.

5. To display the last 16 faults (if any):

A. Press F4 (exit) to return to the screen shown

at the top if this page.

2. From this menu, select F1 (Monitor). The fol-

lowing menu appears:

B. Press F2 (last 16 faults).

F 1 : M o n i t o r I / O

F 2 : F a u l t s

Clearing Field Control Faults

If faults are present, pressing the HHM Clear key

here has no effect. To clear faults from the

F 3 : P r e v i o u s M e n u

Hand-held Monitor you need to do the following:

1. Return to the HHM Main Menu.

2. Press F2 (Analyze).

3. Select F2 (faults) to display fault information

for the Field Processor and its modules.

3. Press F3(Block./ Bus Status).

The Faults menu appears:

4. Make the BIU or Field Processor the active de-

vice if it is not.

F 1 F i r s t 1 6 F l t s

F 2 L a s t 1 6 F l t s

5. Press the Clear key.

Clearing faults from the Hand-held Monitor does

not clear faults at the host PLC. To keep the entire

system in step and up-to-date, fault clearing

should be performed from the host PLC.

F 3 P r e v i o u s M e n u

GFK-0121E

5-16

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Pulse Testing Outputs on Discrete Genius Blocks

Pulse Testing verifies the ability of outputs on a

Clearing Pulse Test Faults

discrete block to change state. Pulse Testing also

indicates whether output circuits (wires, power

sources, loads) will start or stop current flow.

Pulse testing is recommended for blocks

controlling outputs that seldom change state. It

provides assurance that when needed, an output

will operate correctly. Blocks that control outputs

which frequently change state do not need to use

the Pulse Test feature. Pulse Testing does not

provide enough energy to activate mechanical

devices such as motor starters, relays, or solenoid

valves, but it may change the state of a very small

load.

If you press the CLEAR key from the Pulse Test

screen, all faults on the block will be cleared.

If you press the Clear key from the

Monitor/ Control screen (after displaying a specific

circuit fault), only that fault will be cleared.

Pulse Test Error Messages

If the Pulse Test cannot be performed or if the

block fails to respond, an error message appears.

Press the Clear key to remove the message.

E: P U L T S T D I S A B L E

Executing a Pulse Test

A Pulse Test cannot be performed unless the

block’s configuration is changed.

(To execute a Pulse Test, the Hand-held Monitor ’s

PULSE TEST capability must be enabled). The

block being Pulse Tested must be the active block.

E: I N V L D B L K T Y P E

The block does not support Pulse Tests.

E: I N V L D B L K C O N F I G

The active block is an inputs–only block.

E: P U L S E T E S T F A I L

1. From the Analyze menu, press F4 (Pulse Test).

The Pulse Test display appears:

P U L S E T E S T

REFS (cktreferences)

N O F A U L T S

e x e c

The HHM has not received an acknowledgement

from the block within the predetermined amount

of time. Retry the test. If it continues to fail, check

the serial bus cable and active block.

For a PLC host, line 2 shows the block’s as-

signed references and its I/ O configuration.

Line 3 shows whether the block has any faults.

2. Press F1 (Execute) to pulse all outputs on the

block once. If the word FAULTS appears, it

means that one or more diagnostic errors have

occurred. Go to the Monitor/ Control menu to

display the specific type of fault that has oc-

curred.

Chapter 5 Monitoring the Bus and its Devices

5-17

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6Reading CPU Memory

This chapter explains how to use a Hand-held Monitor to read data in a specified memory location in a

Series 90–70, Series Six, or Series Five PLC. New data from the specified memory location is displayed

every three seconds.

General Instructions _________________________________________

1. Be sure the Hand-held Monitor is set up for the type of PLC host you want to read data from. (See

page 3-5 for instructions).

2. If the Hand-held Monitor is NOT attached directly to the PLC’s bus controller, or if another device is

designated as “active” when you enter the Device Memory function, use the F4 (SBA) key and enter

the bus controller ’s Device Number (serial bus address).

3. To read data from the selected bus controller, press F4 from the Main Menu and specify the memory

location to be read as instructed below.

6-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Series 90 PLC

For a Series 90-70 PLC, the Hand-held Monitor can

read data from %R, %AI, %AQ,%I, %Q, %T, %M,

%S, %SA, %SB, %SC, and %G memory.

When F3 (entr) is pressed, the HHM displays the

content in either bit or word format, as

appropriate for the selected memory type. For

example, here word data is displayed, because the

selected memory type (%R) is word-based:

For a Series 90-70 PLC, the memory

location/ content screen looks like this example:

D E V I C E M E M O R Y 1 5

% R

W O R D

1 3 9

l o c

t g l c h n g e n t r S B A

From this screen, you can display the current

contents of other locations in the selected memory

type:

The top line shows the currently-selected Device

Number (15 in the example above). Line 2 shows

the memory type currently accessed, and a

reference location within that memory type. In

this example, the selected location is %R0001.

A. Use the F1 ( > ) key to increment the memory

offset (location).

From this screen, use the HHM function keys to:

A. Select a different bus device (press F4 (SBA)).

B. Select another memory type (press F1 (tgl)).

B. Use the F2 ( < ) key to decrement the memory

offset.

C. Use the F3 (loc) key if you want to enter an off-

set from the HHM keypad.

C. Select another reference location (press

F2(chng), then enter the desired numerical

offset).

D. Display the current memory contents of the

specified location (press F3 (entr)).

6-2

Hand-held Monitor User’s Guide – June 1994

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Series Six PLC

For a Series Six PLC, the Hand-held Monitor can

read data from register memory. That includes I/ O

data mapped into register memory, (it is easier to

display I/ O data with the HHM’s Monitor Block or

Monitor Control Reference function).

Enter or Change the PLC Type

To enter or change the PLC type:

1. Press F3 (chng). A cursor appears at the left of

the colon. For a Series Six PLC, enter the num-

ber 32768.

For a Series Six PLC, the Device Memory screen

looks like this example:

2. Press the F3 (entr) key.

Enter or Change the Memory Location

D E V I C E M E M O R Y 7

MEM: (location)

To enter or change the memory location:

1. On the same screen, press F1 ( > ) to move the

cursor to the right of the colon.

t g l c h n g e n t r S B A

2. Press F2 (chng).

3. Enter a number equal to the actual register

number plus 16383. For example, for regis-

ter#100, you would enter (16383 + 100), which

is 16483:

The top line shows the currently-selected Device

Number (7 in the example above). If there is a

currently-selected memory location, it appears on

the second line of the display as two numbers

separated by a colon.

ME M : 3 2 7 6 8 : 1 6 4 8 3

The number on the left will be:

32768 for a Series Six PLC

Expanded I/O Data

The number on the right is the actual memory

location that will be read.

Expanded I/ O data is mapped into registers and

can be accessed as described above. I/ O data from

channel 0, or the main I/ O chain in an expanded

I/ O system can be displayed using the integer

result of the following formula:

From this screen, use the Hand-held Monitor

function keys to:

A. Select a different device on the bus (press F4

(SBA)).

((point number – 1) / 8) + table offset

B. Select another memory type (press F2 (chng)).

See right for instructions.

The table offset is either 8192 for the output table

or 8320 for the input table. Example: to display

input 672, you would enter: ((672 – 1) / 8) +8320,

which is 8403.

C. Select another reference location in the dis-

played memory type (press F2(chng)). See

right for instructions.

D. Display the current memory contents of the

specified location (press F3 (entr)).

Chapter 6 Reading CPU Memory

6-3

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Series Five PLC

For a Series Five PLC, the Hand-held Monitor can

read data from register memory. That includes I/ O

data mapped into register memory, (it is easier to

display I/ O data with the HHM’s Monitor Block or

Monitor Control Reference function).

Enter or Change the PLC Type

To enter or change the PLC type:

1. Press F3 (chng). A cursor appears at the left of

the colon. For a Series Six PLC, enter the num-

ber 32768.

For a Series Five PLC, the Device Memory screen

looks like this example:

2. Press the F3 (entr) key.

Enter or Change the Memory Location

D E V I C E M E M O R Y 7

MEM: (location)

To enter or change the memory location:

1. On the same screen, press F1 ( > ) to move the

cursor to the right of the colon.

t g l c h n g e n t r S B A

2. Press F2 (chng).

3. Enter the byte offset of the data. This is equal

to (2 x register #) – 2. For example, for regis-

ter#100, you would enter (2 x 100) – 2, which

is 198.

The top line shows the currently-selected Device

Number (7 in the example above). If there is a

currently-selected memory location, it appears on

the second line of the display as two numbers

separated by a colon.

I/O Data

Series Five I/ O data can be displayed using the

integer result of this formula:

The number on the left will be:

133

for a Series Five PLC

(point number) / 8 + table offset

The number on the right is the actual memory

location that will be read.

The table offsets for Series Five I/ O are:

From this screen, use the Hand-held Monitor

function keys to:

channel 1 inputs

channel 2 inputs

channel 1 outputs

channel 2 outputs

32768

32896

33024

33152

A. Select a different device on the bus (press F4

(SBA)).

B. Select another memory type (press F2 (chng)).

See right for instructions.

Example: to display channel 2 output 12, you

would enter:12/ 8 + 33152, which is 33153:

C. Select another reference location in the dis-

played memory type (press F2(chng)). See

right for instructions.

ME M :

1 3 3 : 3 3 1 5 3

D. Display the current memory contents of the

specified location (press F3 (entr)).

Press F3 (ENTR) to save the memory location. To

display the memory content of this location, press

F3 (ENTR) again.

6-4

Hand-held Monitor User’s Guide – June 1994

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the Data Format

When the memory display first appears, it looks

like this example:

Changingthe Selected Address

To change the address being monitored, press F3

(ADDR). The HHM shows:

D E V I C E M E M O R Y

M E M :

W O R D

1 : 6 5 5 2 4

1 2 3 4 5

D E V I C E M E M O R Y

MEM: (location)

WORD (value)

v a l a d d r

< l o c

You can display either one byte or one word of

data. You can also select either decimal display:

To Display Information from Another Device:

press F3 (Location). The function key assignments

change. Now press F4 (SBA). Select the new

Device Number then press F3 (ENTR).

W O R D

B Y T E

1 2 3 4 5

or binary display:

To Increment or Decrement the Memory Address:

use the F1 ( > ) and F2 ( < ) keys.

4 4 1 4 4 11 1 4 4 4 4 4 4 11

To Enter a New Address: press F3 (LOC). Line

4displays new function key assignments. Key in

the memory location as explained previously.

4 4 4 4 4 4 11

To change the data format:

1. Press F2 (VAL).

2. Use the function keys to select the format you

want.

3. Press the D MENU key to return to the pre-

vious screen, where the value will be displayed.

Chapter 6 Reading CPU Memory

6-5

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7Error Messages

This chapter explains error messages that may be displayed on the Hand-held Monitor.

The HHM has a faulty EPROM. Obtain a

replacement or an HHM upgrade kit.

Powerup Error Messages

If an error occurs during the Hand-held Monitor ’s

self-test, this multi-language error display may

appear:

The HHM may have been assigned a De-

vice Number already used on the bus. Press

the ON/ OFF key, then disconnect the HHM

from the device it is attached to. Press the

ON/ OFFkey again. Following the instruc-

tions on page 3-4, assign the HHM a differ-

ent Device Number.

P W R U P E R R O R # 1

E R R E U R

# 1

E I G T E S T : F E H L # 1

E R R O R E I N I Z # 1

At 38.4 Kbaud, unterminated HHM cable

may cause this message. Remove the HHM

cable or check that HHM is connected to a

properly-terminated bus.

This error may occur if the Hand-held Mon-

itor is connected to a bus and an incorrect

baud rate is selected.

Cycle power to the Hand-held Monitor and try

again. If the message returns, look for its error

number in the list at right.

This number indicates an internal fault, or

excessive noise on the bus, or that the bus is

operating at a different baud rate from the

HHM. Press the ON/ OFF key then discon-

nect the HHM cable from the bus

from

the HHM. Press the ON/ OFF key again. If

the message reappears, replace the HHM.

This error may occur if the Hand-held Mon-

itor is connected to a bus and an incorrect

baud rate is selected.

#1, 2, 3, or 6 indicates that the Hand-held Monitor

must be replaced.

7-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Error Messages

Configuration Error Messages

The following messages may appear while

configuring a bus device. They usually indicate an

incorrect selection.

The HHM may display one of the messages

shown below when the ON/ OFF key is pressed or

during operation. If a message appears, press the

Clear key, then follow any action suggested.

E: C O N F I G P R O T E C T

E: N O A C T I V E A D D R

The device’s configuration is protected, its features

cannot be changed. To configure the block, disable

Configuration Protection.

No active device has been selected, so many

functions do not operate. See page 5-2 to select an

active device.

E: N O T O N B L O C K

E: K E Y = M O N T R O N L Y

To configure the Device Number, connect the

HHM directly to that device.

Place the keyswitch in Configure mode (the key

must be present). Press Clear, then retry the

operation. Press Enter.

E: D U P B L O C K N O

The Device Number has already been assigned.

This message only appears if the device is

E: F N C T N D I S A B L E D

connected to a operating bus. Another number

must be assigned to one of the devices in conflict.

The function just selected is disabled by the

HHM’s current configuration. Press the Clear key

to remove the message.

E: D U P L I / O R E F S

E: C O M M E R R O R

The PLC Reference Number conflicts with or

overlaps one already assigned to another device

on the bus. Assign a different reference to one of

the devices in conflict.

HHM cannot communicate with the device. If the

HHM is connected directly to a device which is not

on an operating bus, be sure a terminating resistor is

connected across Serial 1 and Serial 2. If the

message returns, check the bus controller and HHM

cable connections. Try other devices.

E: O U T O F R A N G E

The Reference Number is too high.

E: N O T B Y T E B N D R Y

E: E E P R O M F A I L U R E

The Reference Number does not begin on a byte

boundary (1, 9, 17 . . .).

If you are using the HHM to configure or force a

block, clear the message and go to Block/ Bus

Status menu. Press the Clear key. If the block’s

Unit OK LED continues to blink, power down the

block and replace the TerminalAssembly,

E: I N V A L D B L K C F G

The configuration entry is not valid.

configuring the replacement to match the original.

E: N O S U C H D E V I C E

DI F F E R E N T B A U D

The destination device does not exist. Check the

Device Number.

The HHM and block have been set for different

baud rates: one is set for 153.6Kbaud standard and

the other is set for 153.6 Kbaud extended (the

HHM will not communicate with the bus if any

baud rate conflict exists). All devices on the bus

must be set to the same baud rate.

E: D I F F B L K T Y P E S

Copy Configuration cannot be used between

dissimilar device types.

E: C O P Y E R R O R

Additional Messages: The following additional

messages may appear during normal system use:

An error has occurred during Copy Configuration.

Press Clear and try again.

E: F N C T N D I S A B L E D

E : N O S U C H D E V I C E

E : M O N I T O R O N L Y

E: F N C T N D I S A B L E D

The function is not currently enabled for the

HHM.

GFK-0121E

7-2

Hand-held Monitor User’s Guide – June 1994

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Case, 1-3

AC operation, 2-1

Catalog numbers

Genius blocks and HHM versions, 1-4

HHM, options, accessories, 1-5

AC p ower required, 1-5 , 2-1

Accessories, 1-3

Active device, selecting on HHM, 4-6 , 5-2

, 5-4 , 5-8

Charger, 1-3

catalog number, 1-5

using, 2-1

Adapter

230VAC connector, 2-2

AC power, 2-1

COMM Error message, 3-7

Communications error, 7-2

Alarm d i agnostic, 5-10

Compatibility with other devices, 1-4

Analog blocks

Monitor block screen, 5-5

Monitor/ Control Reference screens, 5-10

Configuration

for bus devices

copying, 4-6

Field Control modules, 4-8

Field Processor, 4-7

Genius blocks, 4-6

grounding required for offline config-

Battery p ack, 1-3

online or offline, 4-2

Program B lock ID, 4-4

Remote I/ O Scanner, 4-5

for perm anently installed HHM, 2-6

sequence for HHM, 3-4

setting up HHM to configure bus de-

vices, 3-6

replacing, 2-3

B a ud rate, 1-5

configuring for bus devices, 4-4

configuring HHM to change for blocks,

3-6

Configuration Protected error, 4-3 , 7-2

error, 7-2

selecting after powering up HHM, 3-2

Connector, external

catalog number, 1-5

installation instructions, 2-9

Block ID, configuring HHM to change for

blocks, 3-5

Copy error, 7-2

Block/ BusStatusdisplay

for Bus Controller, 5-3

for Genius block, Remote I/ O Scanner,

or Field Processor, 5-2

CPU, host, configuring HHM for, 3-5

Current, display for PowerTRAC block,

5-11

Bracket, mounting, 2-7

Bus

d i splaying number of devices on, 5-3

dual

D connector, 2-8

switching, 5-3

Data type, changing when monitoring re-

mote drop, 5-15

viewing presently active bus, 5-4

scan time, display, 5-3

status, 5-3

Description, 1-2

Bus controllers

Device number

Block/ BusStatusdisplay, 5-3

compatibility with HHM versions, 1-4

HHM, 3 -4

of bus device, changing, 4-4

Diagnostics

d i splaying, 5-9

Bus Switching Module, compatibility with

HHM versions, 1-4

Index-1

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

for analog, RTD, or Thermocouple

block, 5-10

viewing present status of circuit on RTD

or Therm ocouple block, 5-5

Function Disabled error, 7-2

Different Baud error, 7-2

Different Block Types error, 7-2

Dimensions, 1-5

Display, 1-5

special characters, 1-3

testing, 3-7

Genius blocks

compatibility with HHM versions, 1-4

I/ O type, 5-4

monitoring with HHM, 5-4

Duplicate Block Number error, 7-2

Duplicate I/ O References error, 7-2

Hardware setup, 2-1

High-speed Counter blocks, Monitor

block screen, 5-6

EEPROM failure, 3-7

High-speed Counter Block

Inputs, display, 5-6

presets, display, 5-6

EEPROM Failure error, 7-2

Error messages, during HHM test, 3-7

Humidity, 1-5

Failed switch diagnostic, 5-9

I/ O forced status, 5-4

Fault clearing

configuring HHM to enable fault clear-

ing, 3-6

I/ O scanning, for Field Processor, disable,

4-8

I/ O type, 5-4

from B lock/ B u s S tatus screen, 5-3

on analog, RTD, or Thermocouple

block, 5-10

on discrete, relay or High-speed Count-

er block, 5-9

Input S h orted diagnostic, 5-10

Installation, instru c tions, 2-6 , 2-7

Installed HHM, configuration sugges-

tions, 2-6

on remote drop, 5-14 , 5-16

Internal Fault diagnostic, 5-10

Features, 1-1

Invalid Block Configuration error, 7-2

Feedback Error diagnostic, 5-10

Field Control products, compatibility with

HHM versions, 1-4

Field Processor, configuration overview,

4-7

Key=Monitor error, 7-2

Keypad, 1-1 , 1-2

testing operation, 3-7

ForcingI/ O

configuring HHM to perform , 3 -6

on analog, RTD, or Thermocouple

block, 5-10

on Monitor/ Control Reference screen,

on remote drop, 5-14 , 5-15

viewing present status, 5-4

viewing present status of analog circuit,

5-5

Languages, 1-1 , 1-5 , 3-5

GFK-0121E

Index-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

LCD display, 1-1

PowerTRAC block

data sequence, 5-11

d i splay data, 5-7

Loss ofI/ O Power diagnostic, 5-9

Low power, 2-3

Monitor/ Control Reference screens, 5-11

Poweru p, 3 -2

Powerup Error messages, 7-1

Program B lock ID screens, 4-4

PROM, changing, 2-4

Memory, reading, 6-1

Menus, main, 3-3

Pulse Testing outputs, 5-17

Monitor B lock screens, 5-4

Monitor Only error, 7-2

Monitor/ ControlReference screens

for Field Processor, 5-15

for Genius blocks, 5-8

for Remote I/ O Scanner, 5-13

Re d undant bus, 5-4

switching, 5-3

References

Monitoring, menus, 5-1

Mounting bracket, 2-7

asterisks appear on screen, 5-2

not on byte bundary, 7-2

of Genius block, displaying, 5-4

Relay blocks, monitor block screen, 5-5

Remote drop, configuration, 4-5

No Active Address error, 7-2

No Faults diagnostic, 5-12

No L oad diagnostic, 5-9

No Such Device error, 7-2

Not Byte Boundary error, 7-2

Not on Block error, 7-2

Remote I/ O Scanner

compatibility with HHM versions, 1-4

configuring I/ O map, 4-4 , 4-5

RTD blocks

Monitor block screen, 5-5

Monitor/ Control Reference screens, 5-10

Serial bus address

Open Wire diagnostic, 5-9 , 5-10

configuring for HHM, 3-4

error caused by duplicating, 7-2

of bus device, changing, 4-4

Operating time, 1-5

Out of Range error, 7-2

Series 90 PLC

Overload diagnostic, 5-9

reading memory, 6-2

references displayed, 5-2

selecting as host type, 3-5

Overrange diagnostic, 5-10

Overtemperature diagnostic, 5-9 , 5-10

Series Five PLC

reading memory, 6-4

references displayed, 5-2

selecting as host type, 3-5

Series Six PLC

PCIM/ Q B IM, selecting as host, 3-5

Power, display for PowerTRAC block, 5-11

Power sources, 2-1

reading memory, 6-3

references displayed, 5-2

selecting as host type, 3-5

Index-3

GFK-0121E

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

S h ort Circuit diagnostic, 5-9

Shutoff

automatic, 2-3

Underrange diagnostic, 5-10

Upgrading the HHM, 2-4

configuring for HHM, 3-5

S p ecifications, 1-5

VARs, display for PowerTRAC block, 5-11

Voltage, display for PowerTRAC block,

5-11

Temperature specifications, 1-5

Testing, 3-7

Thermocouple blocks

Watt-hours, display for PowerTRAC block,

5-11

Monitor block screen, 5-5

Monitor/ Control Reference screens, 5-10

Wiring Error diagnostic, 5-10

GFK-0121E

Index-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Sennheiser Microphone sm 1008 User Manual
Snom IP Phone snom 370 User Manual
Sony Computer Monitor SDM HS95P S User Manual
Sony Printer DPP FP55 User Manual
Sony Video Game Console SCPH 90004 User Manual
Southwing Bluetooth Headset SC705 User Manual
Sterling Water System 2000HG User Manual
Sterling Water System SGM 250A User Manual
Subaru Robin Power Products Portable Generator EY15 3D User Manual
Summer Infant Car Seat 13010 User Manual