OPERATOR’S
MANUAL
Single Stage
Snowthrower
520M Models
Mfg. No.
1693643
1693645
85630
Description
520M, 5HP Snowthrower, Manual Start
520M, 5HP Snowthrower, Manual Start (CE)
SS5200R, 5HP Snowthrower, Manual Start
520E Models
Mfg. No.
1693644
85631
Description
520E, 5HP Snowthrower, Electric Start
SS5200E, 5HP Snowthrower, Electric Start
1720536-03
Rev 5/2003
TP 100-2290-03-SW-SN
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
The triangle
in text signifies important cautions or warnings which must be followed.
GENERAL OPERATION
• Read, understand, and follow all instructions in the
manual and on the unit before starting.
• Only allow responsible adults, who are familiar with
the instructions, to operate the unit (local regulations
can restrict operator age).
• Data indicates that operators, age 60 years and
above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the unit safely enough
to protect themselves and others from injury.
• All operators should seek and obtain professional
and practical instruction.
• Always wear substantial footwear and appropriate
winter clothing. Wear foot-ware that improves trac-
tion on slippery slopes. DO NOT wear long scarves
or loose clothing that could become entangled in
moving parts.
• Before using, always visually check that all hardware
is present, in-tact, and secure. Replace worn or
damaged parts.
• Never operate the machine with defective guards, or
without safety protective devises in place.
• Stop engine before: refuelling, removing an attach-
ment, making adjustments (unless the adjustment
can be made from the operator’s position).
• Follow the manufacturer’s recommendation for wheel
weights or counterweights.
• Clear the area of objects such as rocks, toys, wire,
etc., which could be picked up and thrown.
• Be sure the area is clear of other people. Stop unit if
anyone enters the area.
• Always look down and behind before and while trav-
elling in reverse.
• Be aware of the discharge direction and do not point
it at anyone. Do not point the discharge at glass
enclosures, automobiles, or windows.
• Disengage all clutches (release drive and auger con-
trol levers) before starting the engine.
• Never leave a running unit unattended. Always disen-
gage the auger and traction controls, stop engine,
and remove keys.
• Stop engine before unclogging chute.
• Operate only in daylight or good artificial light.
• Do not operate the unit while under the influence of
alcohol or drugs.
• Adjust skid shoe height to clear gravel or crushed
rock surfaces.
• Do not touch snowthrower parts which may be hot
from operation. Allow such parts to cool before
attempting to service the unit.
• Watch for traffic when operating near or crossing
roadways.
• Use extra care when loading or unloading the unit
into a trailer or truck.
• Keep in mind the operator is responsible for acci-
dents occurring to other people or property.
SLOPE OPERATION
Do
• See your authorized dealer for recommendations
counterweights to improve stability.
WARNING
Never operate on slopes greater than 17.6 percent (10°) which
is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm)
horizontally.
• Travel up and down slopes, not across.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Snow can hide obstacles.
• Use slow speed. Tires may lose traction on slopes.
Choose a low gear so that you will not have to stop or
shift while on the slope.
When operating on slopes use additional wheel weights or
counterweights. See your dealer to determine which weights
are available and appropriate for your unit.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
• Always keep unit in gear especially when traveling
downhill.
Select slow ground speed before driving onto slope. Travel
UP and DOWN the slope, never across the face, use caution
when changing directions and DO NOT START OR STOP ON
SLOPE.
Do Not
• Do not start or stop on a slope. If tires lose traction,
disengage the auger and proceed slowly straight
down the slope.
Slopes are a major factor related to loss-of-control and tip-
over accidents, which can result in severe injury or death.
All slopes require extra caution. If you cannot back up the
slope or if you feel uneasy on it, do not operate on it.
• Do not turn on slopes unless necessary, and then,
turn slowly and gradually downhill, if possible.
• Do not operate near drop-offs, ditches, or embank-
ments. The unit could suddenly turn over if a wheel is
over the edge of a cliff or ditch, or if an edge caves in.
• Do not operate on wet surfaces. Reduced traction
could cause sliding.
• Do not shift to neutral and coast down hills.
TP-600-3606-00-LW-UV
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
EMISSIONS
CHILDREN
• Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth
defects, or other reproductive harm.
• Look for the relevant Emissions Durability Period and
Air Index information on the engine emissions label.
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
unit and the operating activity. Never assume that children
will remain where you last saw them.
• Keep children out of the area and under the watchful
care of another responsible adult.
• Be alert and turn unit off if children enter the area.
• Before and during reverse operation, look behind and
down for small children.
• Never allow children to operate the unit.
• Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
SERVICE AND MAINTENANCE
• Use extra care in handling gasoline and other fuels.
They are flammable and vapors are explosive.
a) Use only an approved container.
• Keep unit free of debris build-up. Clean up oil or fuel
spillage.
• Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.
• Never make adjustments or repairs with the engine
running unless specified otherwise in the engine
manufacturer’s manual.
b) Never remove gas cap or add fuel with the
engine running. Allow engine to cool
before refueling. Do not
c) Never refuel the unit indoors.
• If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
• Replace all fuel tank caps and fuel container caps
securely.
• Never fill containers inside a vehicle or on a truck bed
with a plastic bed liner. Always place containers on
the ground away from your vehicle before filling.
• Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possi-
ble, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dis-
penser nozzle.
• Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is com-
plete. Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immedi-
ately.
• Maintain or replace safety and instruction labels as
necessary.
• Never run a unit in an enclosed area.
• Keep nuts and bolts tight and keep equipment in
good condition.
• Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if
they are not functioning properly.
smoke.
• Components are subject to wear, damage, and dete-
rioration. Frequently check components and replace
with manufacturer’s recommended parts, when nec-
essary.
• Check control operation frequently. Adjust and ser-
vice as required.
• Use only factory authorized replacement parts when
making repairs.
• Always comply with factory specifications on all set-
tings and adjustments.
• Only authorized service locations should be utilized
for major service and repair requirements.
• Never attempt to make major repairs on this unit
unless you have been properly trained. Improper ser-
vice procedures can result in hazardous operation,
equipment damage and voiding of manufacturer’s
warranty.
• Do not change engine governor settings or over-
speed the engine. Operating the engine at excessive
speed can increase the hazard of personal injury.
• Disengage auger and traction, stop the engine,
remove the key, and disconnect the spark plug
wire(s) before: clearing blockages and chutes, per-
forming service work, striking an object, or if the unit
vibrates abnormally. After striking an object, inspect
the machine for damage and make repairs before
restarting and operating the equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
ANSI B71.3-1995 WARNINGS
Training
6. When cleaning, repairing, or inspecting make certain
the collector/impeller and all moving parts have
stopped. Disconnect the spark plug wire and keep
the wire away from the plug to prevent accidental
starting.
7. Do not run the engine indoors except for starting the
engine or for transporting the snowthrower in or out
of the building. Open the outside doors; exhaust
fumes are dangerous.
8. Do not clear snow across the face of slopes.
Exercise extreme caution when changing direction on
slopes. Do not attempt to clear steep slopes.
9. Never operate the snowthrower without proper
guards plates, or other safety protective devises in
place.
10. Never operate the snowthrower near glass enclo-
sures, automobiles, window wells, drop-offs, and the
like without proper adjustment of the discharge angle.
Keep children and pets away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when backing.
13. Never direct discharge at bystanders or allow anyone
in front of the unit.
1. Read the operating and service instruction manual
carefully. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
3. Keep the area of operation clear of all persons, par-
ticularly small children and pets.
4. Exercise caution to avoid slipping or falling especially
when operating in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is
to be used and remove all doormat, sleds, boards,
wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting engine (motor).
3. Do not operate the equipment without wearing ade-
quate winter outer garments. Wear footwear that will
improve footing on slippery surfaces.
4. Handle fuel with care; it is highly flammable.
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
(d) Replace fuel cap securely and wipe up spilled
fuel.
14. Disengage power to the collector/impeller when
snowthrower is transported or not in use.
15. Use only attachments and accessories approved by
the manufacturer of the snowthrower (such as wheel
weights, counterweights, cabs, and the like).
16. Never operate the snowthrower without good visibility
or light. Always be sure of your footing, and keep a
firm hold on the handles. Walk, never run.
5. Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive
motors or electric starting motors.
6. Adjust the collector housing height to clear gravel or
crushed rock surfaces.
7. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by the manufacturer).
8. Let engine (motor) and machine adjust to outdoor
temperatures before starting to clear snow.
9. Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair
to protect eye from foreign objects that may be
thrown from the machine.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent inter-
vals for proper tightness to be sure the equipment is
in safe working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water and spacer heaters, clothes dryers,
and the like. Allow the engine to cool before storing
in any enclosure.
3. Always refer to the operator’s guide instructions for
important details if the snowthrower is to be stored for
an extended period.
4. Maintain or replace safety and instruction labels as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
• Always observe safe refueling and fuel handling prac-
tices when refueling the unit after transportation or
storage.
• Always follow the engine manual instructions for stor-
age preparations before storing the unit for both short
and long term periods.
Operation
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic.
3. After striking a foreign object, stop the engine
(motor), remove the wire from the spark plug, discon-
nect the cord on electric motors, thoroughly inspect
the snowthrower for any damage, and repair the
damage before restarting and operating the
snowthrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the
collector/impeller housing or discharge guide, and
when making any repairs, adjustments, or inspec-
tions.
• Always follow the engine manual instructions for
proper start-up procedures when returning the unit to
service.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Identification
Identification Numbers
North American
Models
ID Tag
Mfg. No.
Serial No.:
kW:
Engine RPM XXX
LpA:
169XXXX
XXXXX
X
2002
dB(A)
CE Models
PRODUCT REFERENCE DATA
Model Description Name/Number
XXX dB(A)
Vibration @ WheelXXX m/s²
Simplicity Mfg. Inc.
Port Washington, WI USA 53074-097
Unit MFG Number
Unit SERIAL Number
When contacting your authorized dealer for replace-
ment parts, service, or information you MUST have
these numbers.
Mower Deck MFG Number
Mower Deck SERIAL Number
Date Purchased
Dealer Name
Record your model name/number, manufacturer’s identi-
fication numbers, and engine serial numbers in the
space provided for easy access. These numbers can be
found in the locations shown.
ENGINE REFERENCE DATA
Engine Make
Engine Model
NOTE: For location of engine identification numbers,
refer to the engine owner’s manual.
Engine Type/Spec
Engine Code/Serial Number
CE Models: Place the extra copy of the identification tag
in the manual
CE IDENTIFICATION TAG MARKINGS
A. Manufacturer’s Identification Number
B. Manufacturer’s Serial Number
C. Power Rating in Kilowatts
D. Maximum Engine Speed in Rotations per Minute
E. Manufacturer’s Address
F. Year of Manufacture
G
A
B
F
I
C
Mfg. No.:
169XXXX
XXXXX
XXX
Serial No.:
kW:
2002
D
dB(A)
Engine RPM XXXX
XXX dB(A)
Vibration @ Wheel: XXX m/s²
J
LpA:
K
Simplicity Mfg. Inc.
G. CE Compliance Logo
Port Washington, WI USA 53074-0997
H
H. Mass of Unit in Kilograms
E
I. Sound Power in Decibels ***
J. Sound Pressure at Operator’s Position in Decibels **
K. Vibration*
This unit complies with European Harmonized Lawn Mower
Standard EN 836, European Machinery Directive 98/37/EC,
and European EMC Directive 89/336/EC
CE Models:
Place copy of
Identification Tag here.
* Tested according to EN 836:1997/A2:2001, EN 1032:
1996, EN 1033:1995
** Tested according to EN836:1997/A2:2001
*** Tested according to 2000/14/EC
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
SAFETY DECALS
Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the opera-
tor of the most important safety precautions. All warning, caution and instructional messages on your snowthrow-
er should be carefully read and obeyed. If any of these decals are lost or damaged, replace them at once. They
can be purchased from your local dealer.
Part No. 1716672
Auger Control Decal
Part No. 1716669
Main Dash Decal (Electric Start Models)
Part No. 73461
Warning Decal
Part No. 1716670
Main Dash Decal (Manual Start Models)
Part No. 73844
Warning Decal -
Fire Hazard, Do
Not Stand Unit on
End
Part No. 1716532
Auger Danger Decal
Part No. 1722674
Discharge Chute Danger Decal
International Symbols
FAST
CHOKE
IGNITION KEY
SLOW
STOP
PRIMER
RUN
ELECTRIC START
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling
the Snowthrower
TOOLS REQUIRED
• Socket or Wrench Set
A
• Pair of Pliers
ASSEMBLY PROCEDURE
C
If your unit was not previously assembled, see Figures 1
and 2, and follow the steps below to assemble the unit:
D
1. Install the discharge chute on to the rotating ring
located on the auger housing. Secure with the three
5/16 inch carriage bolts, flat washers and nylock nuts
found in the parts bag (the bolt heads go to inside of
of the rotating ring, with washers and nuts on the out-
side). Note, install the rear bolt first for easier align-
ment.
E
B
2. Tighten bolts securely with a wrench.
Figure 1. Assembly of Discharge Chute
3. Lift up folding handle to align it with lower handle and
tighten the wing knobs securely as shown in Figure 3.
A. Discharge Chute
B. Carriage Bolts
C. Washers
D. Nuts
E. Rotating Ring
The snow thrower is now ready for operation once the
fuel tank has been filled with the properly mixed gasoline
and two cycle oil.
A
B
Figure 2. Handles
Figure 3. Lift Handles and Lock Wing Knobs
A. Handle
B. Wing Knobs
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
& Operation
SNOWTHROWER CONTROLS
A
Auger Control
C
A. Auger Control - This control engages and disen-
gages the auger. Pull the control back against handle
to engage the auger, (this will pull snowthrower for-
ward if auger is in contact with the ground). Release
the Auger Control to stop rotation of auger.
B
Deflector Controls
B. Chute Direction Control - The Chute Direction
Control (B, Figures 4&5) allows the discharge chute
to be rotated to throw snow in the desired direction.
Snow may be thrown at any angle from straight left to
straight forward, to straight right.
The length of the chute direction control can be
adjusted. Remove the cotter pin (A, Figure 5) to
extend or shorten the rod to desired length, then rein-
stall the pin.
C. Chute Deflector - Controls the distance snow is
thrown. Tilting the Chute Deflector (C, Figure 4) UP
provides a higher stream and greater distance, while
tilting the deflector DOWN provides a lower stream
and less distance.
Figure 4. Snowthrower Controls
A Auger
Engages auger when pulled
Control
back, and disengages auger
when released.
A
B Chute
Direction
Control
Rotates discharge chute to
desired direction
C Chute
Controls vertical angle snow is
thrown.
B
Deflector
Figure 5. Discharge Chute Control Adjustment
A. Cotter Pin
B. Chute Direction Control
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Operation
ENGINE & STARTING CONTROLS
C
NOTE: Throttle - This snow thrower does NOT have a
throttle for controlling operating speed of engine. The
engine governor maintains operating speed for vary-
ing snow removal conditions.
B
Electric Start Units Only
A. Electric Start Button - The Electric Start Button (A,
Figure 6) activates an electric starter mounted to the
engine, eliminating the need to pull the starter han-
dle. The Electric Start Button operates on 120 Volts
AC, which is provided by connection to the extension
cord provided with units equipped with this feature.
Connect this extension cord ONLY to a properly
grounded 3 prong electrical outlet.
E
All Models
B. Fuel Tank Cap - Cover fuel tank & provides venting
F
A
ability to prevent vapor lock.
D
C. Starter Handle - The starter handle (C, Figure 6)
connects to a starter cord to manually start the
engine. Pulling starter handle rapidly spins the engine
crankshaft, cycles the engine, and generates the
spark necessary for starting the engine.
Figure 6. Engine Controls
A
B
C
D
E
F
Electric Start
Button
(Optional)
Activates electric starter
D. Primer Button - When pressed, the Primer Button
(D, Figure 6) provides initial fuel to help start a cold
engine. Normally, pressing the primer button twice
will provide enough fuel to start a cold engine.
Fuel Tank
Cap
Covers fuels tank and provides
venting to prevent vapor lock
E. Engine Key - Insert key in switch and turn key to ON
position when starting engine. To stop engine, turn
key to OFF position.
Starter Handle Used to start engine
F. Choke Control - The is control (F, Figure 6) adjusts
the fuel/air mixture, and is used to help start a cold
engine by providing a richer mixture.Once the engine
is warm and running smoothly, the Choke Control
should be set to the off position to provide a normal
air/fuel mix.
Primer Button Primes carburetor for faster cold
starting.
Engine Key
Prevents starting of engine with-
out key. Stops engine when
removed.
Choke Control Adjusts air/fuel mixture
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Operation
GENERAL OPERATION
CHECKS BEFORE EACH START-UP
1. Make sure all safety guards are in place and all nuts,
bolts and clips are secure.
WARNING
To avoid serious injury, do not put your hands into
the auger housing or discharge chute. If auger stalls
or chute becomes plugged, use the following proce-
dure to remove objects or clear the chute:
2. Check the fuel supply. Fill the tank no closer than 1/4
to 1/2 inch of top of tank to provide space for expan-
sion. See your engine Owner’s Manual for fuel rec-
ommendations.
1. Release the Auger Control.
2. Shut off the engine.
3. Remove the Engine Key.
4. Wait for moving parts to stop.
5. Use a narrow board to remove foreign objects
and clear the chute or auger. Never put your
hands into the auger or discharge chute.
3. Check the Auger Control (see A, Figure 4) for proper
operation. If adjustment is required, see the Service
section (pages 13-15) for procedures.
4. Check the Chute Direction Control (B, Figure 4) for
proper operation. The discharge chute should rotate
freely in both directions. See the Service section for
adjustment procedures and troubleshooting.
6. If servicing is needed, remove cover and dis-
connect spark plug wire.
5. Check the Chute Deflector (C, Figure 4) for proper
operation. The deflector should pivot freely up and
down. See the Service Section for procedures.
WARNING
6. Position the chute at the desired starting direction
and set the deflector at the desired angle.
For your safety, operation on slopes should be in an
up and down direction only. If it becomes necessary
to move across the face of a slope, use caution and
do not blow snow. Be very careful when changing
direction on a slope.
Proper winter footwear is recommended for the
operator to help prevent slipping. Never attempt to
clean snow from excessively steep slopes. The
maximum slope for any operation is 17.7% (10º).
WARNING
Gasoline is highly flammable and must be handled
with care. Never fill the tank when the engine is hot or
running. Always move outdoors to fill the tank. Keep
snowthrower and gasoline away from open flame or
spark.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Operation
FUEL AND OIL MIXTURE
The snowthrower uses a two cycle engine that requires a
mixture of fuel (gasoline) and oil for lubrication of engine
bearings and other moving parts.
FUEL TO OIL MIXTURE CHART (50:1)
U.S. Imperial Metric
Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil
Gallons
Ounces
2.5
5
Gallons
Ounces
Liters
Milliliters
The correct fuel/oil mixture ratio for the five horsepower
engine is 50 to 1. Use fuel/oil mixture chart shown.
1
2
5
1
2
5
2.8
4
80 ml
5.6
8
160 ml
400 ml
NOTE: To prevent damage to engine, carefully
observe recommended fuel to oil mixing ratio and
procedures.
13
14.1
20
• Gasoline and oil must be premixed in a clean fuel
container.
• Always use fresh, unleaded, winter grade fuel
• Never put plain, unmixed fuel into fuel tank. Shake
fuel container each time before filling fuel tank.
WARNING
Gasoline is highly flammable and must be handled
with care. Never fill the tank when the engine is hot or
running. Always move outdoors to fill the tank. Keep
snowthrower and gasoline away from open flame or
spark.
• Never use “stale” fuel left over from last season or
stored for long periods.
• DO NOT USE MULTI VISCOSITY OILS, SUCH AS
10W-30 or 10W-40.
PROPER FUEL MIXING PROCEDURE
1. Fill approved clean fuel container one quarter full with
fresh unleaded fuel - one quart (one liter) in a one
gallon (4 liter) container.
A
B
C
D
2. Pour recommended amount of high quality two
cycle oil — 2.5 ounces (80 ml) into fuel container for
one gallon (4 liters) of fuel. (NOTE: DO NOT USE
MULTI VISCOSITY OILS, SUCH AS 10W-30 or
10W-40.)
3. Reinstall cap on the fuel container and shake con-
tainer vigorously so oil mixes with gasoline.
4. Unscrew cap and fill container with fuel. Shake con-
tainer again.
5. Remove fuel tank cap and carefully pour mixed fuel
into the fuel tank, filling to 1/2 inch (1.5 cm) below
filler neck to allow room for expansion. Never put
plain, unmixed fuel into fuel tank. Shake fuel con-
tainer each time before filling fuel tank.
Figure 7. Proper Fuel Mixing Procedure
A. Fill Container with 1 Quart (1 Liter) of fuel
B. 2.5 Ounces (80 ml) of two-cycle oil
C. Combine in container, then shake container
D. Additional fuel brings total to 1 Gallon (4 liters)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Operation
STARTING THE ENGINE
DANGER
NOTE: The snow thrower engine is designed to operate
at cold temperatures. Avoid operating the snow thrower if
air temperature is 40° C or warmer since engine may
vapor lock and stop running after a short time. Engine
will be difficult to start in warm weather.
Never run engine indoors or in enclosed, poorly venti-
lated areas. Engine exhaust contains CARBON
MONOXIDE, an ODORLESS and DEADLY GAS.
Manual (Recoil) Starting Steps
Electric Starting Steps
1. Insert engine key in switch and turn key to the ON
position.
Note: The electric starter is designed to operate on 120V
AC household current, using power cord supplied with
electric start snow thrower. When using power cord,
match wide blade of plug to wide slot of receptacle.
2. If engine is cold, move choke control lever to the ON
position. (Do not choke a warm engine).
1. Insert engine key in switch and turn key to the ON
position.
3. Push the Primer Button two times if engine is cold.
(Do not prime a warm engine.)
2. If engine is cold, move choke control lever to the ON
position. (Do not choke a warm engine).
4. Grasp starter rope handle and slowly pull out rope
until resistance is felt. Allow rope to rewind slowly,
then pull rope out rapidly to start engine. Let rope
return slowly to starter.
3. Push the Primer Button two times if engine is cold.
(Do not prime a warm engine.)
NOTE: If engine does not start after three pulls,
push primer bulb once and again pull starter
rope.
4. Plug power cord for starter into receptacle on starter
switch, then plug other end into a 120Volt AC house-
hold receptacle. DO NOT use an extension cord with
the electric start power cord supplied.
5. After engine starts and gradually warms up, move
choke lever to the OFF position. Be prepared to
move choke lever to the ON position if engine falters
during warm up.
CAUTION
Be sure there is no moisture present on cord ends or
receptacles when plugging cord into receptacle.
6. Allow engine to warm up before beginning snow
thrower operations. The engine will operate at full
throttle when thoroughly warmed up.
5. Push starter button to crank engine. DO NOT crank
engine for more than a total of 15 seconds without
allowing electric starter to cool for 10 minutes before
additional cranking is attempted. Electric starter can
be severely damaged if recommended starter operat-
ing limitations are not observed.
7. To stop engine, turn Engine Key to the OFF position.
STOPPING THE ENGINE
1. Release the Auger Control.
NOTE: Do not push primer button while engine is
being cranked.
2. Turn Engine Key to the OFF position.
3. Remove the key from the switch if you are leaving the
operating position or will be making adjustments or
repairs. (NOTE: Allow the unit to cool before storing
or making any adjustments or repairs.)
6. Release starter button when engine starts and gradu-
ally move choke lever to the OFF position.
NOTE: Always disconnect power cord from
household receptacle first, then unplug from
starter switch.
If you will be storing the unit for the season, see the
STORAGE section for instructions on properly preparing
the unit for long-term storage.
7. Disconnect power cord from household receptacle
and then from starter switch on snow thrower. Store
cord in a dry, convenient place.
8. To stop engine, turn Engine Key to the OFF position.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls & Operation
OPERATING THE SNOWTHROWER
AFTER EACH USE
Before operating snowthrower, review the Checks Before Allow snow thrower to run a few minutes after clearing
Each Use under General Operation on page 8 of this
manual.
snow to reduce the likelihood of parts freezing while
machine is not is use.
1. Rotate the discharge chute to the desired direction.
If you will be storing the unit for the season, see the
STORAGE section for instructions on properly preparing
the unit for long-term storage.
2. Pull the Auger Control back against the handle to
engage the auger.
OFF-SEASON STORAGE
Before you store your snowthrower for the off-season,
read the Maintenance and Storage instructions in the
Safety Rules section and take the following precautions:
NOTE: The snow thrower will be pulled forward by
the auger when the auger contacts the ground or with
the snow to be thrown.
3. Begin snow removal by clearing a path down the cen-
ter of walk or driveway, then gradually widen path,
throwing snow off to both sides.
NOTE: Gasoline, if permitted to stand unused for extend-
ed periods (30 days or longer), may develop gummy
deposits which can adversely affect the engine carbure-
tor and cause engine malfunction. To avoid this condi-
tion, add Simplicity Gasoline Stabilizer to the fuel tank, or
drain all fuel from the system before placing unit in stor-
age.
4. Release the Auger Control to stop both the auger
and the forward motion of the snowthrower.
WARNING
1. Prepare your snowthrower engine for storage as
instructed in the Engine Owner’s Manual.
Do not use snow thrower on surfaces above ground
level, such as the roof of a building.
2. Lubricate the snowthrower as described in the
LUBRICATION section of this manual.
SNOWTHROWING TIPS
3. Clean the snowthrower thoroughly. Coat exposed
bare metal parts with a quality paint (available from
you dealer) or a light film of grease, oil or automotive
wax.
Discharge chute icing may occur as the result of snow
build up around the base of the discharge chute. If the
chute does freeze up, DO NOT force the control: control
linkage damage may result. Put the unit indoors and
allow the ice to melt, or pour hot water around the inside
and outside base of the discharge chute.
4. Store snowthrower in the wheels down, operating
position. Note: If the unit is stored in any other posi-
tion, fluids may leak.
Varying snow conditions will affect performance of
snow thrower. The snow thrower should be allowed to
move into the snow at it's own pace.
5. Store the unit in a protected area and cover.
STARTING AFTER STORAGE
1. Remove the spark plug and wipe dry. Then reinstall
plug.
Wet, heavy snow — When clearing wet, heavy snow,
the forward movement of the snowthrower may have to
be slowed by pushing down on handle while allowing
engine to operate at full throttle.
2. Fill fuel tank with fresh gasoline (unless a fuel stabi-
lizer was used).
3. Check to be sure engine fins are clean and air flow is
unobstructed.
Do not operate on gravel or crushed rock surfaces.
Avoid picking up this type of material with auger since
damage to unit could result and particles can be dis-
charged with considerable force that could cause serious
injury.
4. Start the engine outdoors. Warm up engine by run-
ning at SLOW speed for a a few minutes before run-
ning at FAST speed, or blowing snow.
5. Check the operation of all the controls. If necessary,
lubricate the snowthrower to improve operation of the
chute control.
Always be alert to hidden hazards that might be struck
by the auger. Should a foreign object be struck by the
auger, immediately stop the engine and inspect machine
for any damage. Repair damage before continuing oper-
ation.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Regular
Maintenance
Removing Belt Cover
In order to perform proper lubrication, it is necessary to
remove the Belt cover from the lower left of the
snowthrower.
Screws
1. Remove the Engine Key from the switch.
2. Remove the fours screws securing the belt cover
(see Figure 8).
3. Remove the cover.
Figure 8. Removing Belt Cover
4. Perform lubrication (see below).
5. Reinstall belt cover (reverse steps 3 to 1 above.)
LUBRICATION
Note: The drive pulley end of auger shaft is supported by
a sealed ball bearing and requires no lubrication. The
ball bearing on other end of auger shaft is also sealed,
and will not require lubrication.
Lightly Oil
• A few drops of oil should be placed on wheel
hubs occasionally to keep wheels turning
freely.
Figure 9. Lubrication points
• Apply oil to pivot points of auger control peri-
odically, wiping off any excess oil.
• A couple of drops of light machine oil applied to
upper end of auger control cable will assure free
movement of cable through outside casing. Wipe off
any excess oil.
Pivot Point
• Remove belt cover and lightly apply oil to the pivot
point for idler pulley arm. BE CAREFUL NOT TO
GET OIL ON BELT OR PULLEYS.
Grease
Figure 10. Lightly oil pivot point
• At the beginning of each snow throwing sea-
son, remove discharge chute and generously
lubricate steel flange at back of rotating ring
with light grease. Rotate ring with crank to dis-
tribute grease.
Lubricate
Flange
Engine Lubrication
The two cycle engine used in this snow thrower is lubri-
cated by the fuel and oil mixture. Observe recommended
fuel to oil mixture ratio shown on page 9.
Figure 11. Grease the Discharge Chute Ring
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
& Service
TROUBLESHOOTING
Problem
Possible Cause
Remedy
Engine fails to start
1. Key is OFF
2. Failure to prime cold engine
3. Out of fuel
1. Turn Key to the ON position
2. Press primer button twice and restart.
3. Fill fuel tank
4. Choke OFF - cold engine
5. Engine flooded
6. Spark Plug not sparking
4. Turn Choke to ON.
5. Turn Choke to OFF; try starting
6. Check Gap. Gap plug, clean electrode,
or replace as necessary
7. Water in fuel, or old fuel
7. Drain tank (Dispose of fuel at an authorized
waste facility). Fill with fresh fuel mixture.
Engine starts hard or runs poorly
Unit does not throw snow
1. Fuel mixture too rich
2. Spark plug faulty, fouled,
or gapped incorrectly
1. Move choke to OFF position
2. Clean and gap, or replace
3. Water in fuel, or old fuel
3. Drain tank (Dispose of fuel at an authorized
waste facility). Fill with fresh fuel mixture.
4. Clean vent hole or replace cap
4. Gas cap vent hole plugged
1. Loose or broken drive belt
2. Incorrect control cable
adjustment
1. Adjust or replace belt
2. Adjust Auger Control cable
3. Discharge chute clogged,
foreign object lodged in auger
4. Broken control cable
3. Stop engine, remove key and
clean out discharge chute
4. Replace cable
Auger does not stop turning
when control is released
1. Incorrect control cable
adjustment
1. Adjust Auger Control cable
Excessive vibration
1. Loose parts or damaged
auger
1. STOP engine and REMOVE the key,
tighten all hardware. If vibration
continues, see your dealer.
Note: For repairs beyond the minor adjustments listed above, please contact your local Simplicity dealer.
REMOVING ENGINE COVER
Note: In many of the following adjustment and service
tasks, it will be necessary to remove and reinstall the
engine cover. To remove the cover, proceed as follows:
Remove
Fuel Tank
Cap
1. Remove the Engine Key from the switch.
2. Remove the two rear fasteners securing the back of
the cover housing. (Figure 12).
3. Remove the fuel tank cap.
4. Remove the cover (see Figure 13 on page 14).
5. Temporarily reinstall the fuel tank cap.
6. Perform the adjustments or service desired.
7. Reinstall the cover by reversing the removal steps.
Note: The tabs at the lower front of the cover must be
positioned correctly.
Remove two
rear fasteners
securing
cover
WARNING
To avoid the possibility of serious bodily injury when
performing adjustments, maintenance or lubrication,
stop engine and remove key from switch.
Figure 12. Remove and/or loosen Cover Screws
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting & Service
Lift Cover
from Rear
of unit
Locknuts
Spring
Insert front
tabs first when
reinstalling
cover.
Align rear
tabs & side of
cover when
reinstalling.
Figure 13. Cover Removal & Installation
Figure 14. Auger Control Cable
Adjusting the Cable
1. Remove the engine cover.
AUGER CONTROL
CABLE ADJUSTMENT
2. Locate and loosen the lower locknut securing the
auger control cable (shown in Figure 14).
The length of the auger control cable is adjustable.
However, it will seldom be necessary to change the
cable length since the operating tension on the drive belt
is maintained by the spring on the end of the cable.
3. To change the slack in the cable, turn the upper lock-
nut slightly just until the slack between the spring
and the exposed cable has been eliminated.
If the auger turns too slowly under heavy load or
momentary squealing of drive belt is heard when enter-
ing heavy snow, pressure applied to drive belt by idler
pulley must be increased by reducing the slack in the
cable.
4. Tighten the lower locknut.
5. Test the units to make certain that the cable has
been adjusted properly.
If the auger continues to turn when the auger control
is released, the cable is too tight. The pressure applied
to the drive belt must be eliminated by increasing the
amount of slack to the cable adjustment.
WARNING
Use extreme care when making adjustments that
require engine to be running. Keep hands, feet, hair
and loose clothing away from any moving parts.
WARNING
Testing the Auger Control Cable
Start the snow thrower engine and pull back on auger
control to operate auger. Release auger control and
check to be sure auger stops turning.
Make certain the cable is NOT placing any tension on
the spring. If the cable places tension on the spring,
the auger may turn when the control has not been
engaged.
If auger continues to turn after auger control is
released, cable is too tight and will have to be adjust-
ed to make it longer. Cable must be slightly slack
when auger control is released (away from handle).
Checking the Adjustment.
1. Remove the Cover. (See page 13.)
2. Measure the spring while the auger control on the
handle is disengaged. Record this measurement.
CARBURETOR ADJUSTMENT
3. Pull the auger control against the handle and again
measure the spring. Record this measurement.
The carburetor is properly calibrated and preset at the
factory for efficient cold weather operation. There are no
adjusting screws on the carburetor.
4. Compare the two measurements. The measurement
obtained with the spring extended should be 7/16
inch (11 mm) greater than with the spring at rest.
If it is apparent that the carburetor is not providing satis-
factory fuel supply to engine, contact your nearest
Authorized Tecumseh Service Outlet for service.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting & Service
REPLACING THE DRIVE BELT
1. Remove Engine Key from switch.
2. Remove belt and engine covers.
Idler
Pulley
3. Move the Auger Control on the handle and slip the
belt out from between the brake lever and roller and
away from the idler pulley.
Engine
Pulley
4. Remove the belt from the engine and auger pulleys.
5. Install new belt around engine and auger pulleys and
under idler pulley. The ribbed side of the belt must be
to the inside, against auger and engine pulleys.
6. Slip the new belt into place between brake lever and
roller.
Brake
Lever/Roller
7. Start the engine and engage/disengage the auger
control several times. Make certain that auger stops
turning within 5 seconds after the control is released.
Drive Belt
Auger Pulley
8. If the auger does not stop turning within 5 second
after the control is released, adjust the tension on the
control cable by following the Adjusting Control Cable
procedure in the adjustments section of this manual.
Figure 15. Drive Belt Replacement
9. Reinstall the belt and engine covers.
REPLACING THE SCRAPER BLADE
1. Remove Engine Key from switch.
2. Remove the two bolts and nuts securing the Scraper
Blade to the auger housing. (Retain the bolts and
nuts for attaching the new blade.)
3. Remove the worn Scraper Blade.
4. Install the new Scraper Blade and secure it with the
three bolts and nuts saved in step 2 above.
Scraper Blade, Bolts & Nuts
Figure 16. Removing Scraper Blade
SERVICING THE SPARK PLUG
1. Remove Engine Key from switch.
2. Remove the engine cover. (See page 13.)
3. Disconnect the wire from the spark plug.
4. Inspect the Spark Plug and clean. If necessary,
replace the it with a new Spark Plug as recommend-
ed in the Engine Owners Manual.
5. Adjust the gap on the Spark Plug to .030 inches
(.762 mm) using a gauge.
Spark Plug
Wire
6. Reinstall the plug and tighten firmly.
7. Reconnect Spark Plug wire.
8. Reinstall engine cover.
Figure 17. Servicing Spark Plug
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.
ENGINE:
CHASSIS:
Spout Rotation
Auger Diameter
Tire Size
220 Depress
9” (22.9cm)
7” x 1.5” (17.8cm x 3.8cm)
5 HP* Tecumseh
Make
Tecumseh
Model
HSK 850
DIMENSIONS
Horsepower
Displacement
Oil Mixture
5 @ 4000 rpm
8.46 Cu. in (139 cc)
50:1
Effective Clearing
Width
20” (51cm)
Length
Height
Weight
42” (107cm)
42” (107cm)
75 lbs (34kg)
Parts & Accessories
REPLACEMENT PARTS
TECHNICAL MANUALS
Replacement parts are available from your authorized
dealer. Always use genuine Simplicity/Snapper Service
Parts.
Additional copies of this manual are available, as well as
fully illustrated parts lists. These manuals show all of the
product’s components in exploded views (3D illustrations
which show the relationship of parts and how they go
together) as well as part numbers and quantities used.
Important assembly notes and torque values are also
included.
MAINTENANCE ITEMS
Many convenient and helpful service and maintenance
items are available from you authorized dealer. Some of
these items include:
For applicable manuals currently available for your
model, contact our Customer Publications Department at
262-284-8519. Have the information listed in the box
below available when phoning in your request.
Technical manuals can be downloaded from
Engine Oil
Tire Sealant
Touch-Up Paint
Grease Gun Kit
8 oz. Grease Tube
Degrimer/Degreaser
Gas Stabilizer
Model:
Mfg. No.:
Your Name:
Address:
City, State, Zip:
Visa/Mastercard No.:
Card Expiration Date:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
PRODUCTS, INC.
McDonough, GA., 30253
© Copyright 2003, Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|