ATTACHMENT
OPERATOR’S
MANUAL
Snow/Dozer
Blade & Hitch
Snow Plow/Dozer Blade
Mfg. No.
Description
1693754
42” Remote Angling Snow Plow/Dozer Blade
Hitch
Mfg. No.
Description
1693757
Hitch (for Sovereign / 900 / 2800 Series)
1721303-01
Rev 1/2001
TP 100-2374-01-AT-SMA
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
& Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
The triangle in text signifies important cautions or warnings which must be followed.
GENERAL WARNINGS
PREPARATION
G Know the tractor controls and how to stop quickly.
G Disengage the PTO before making any adjustments.
READ THE TRACTOR OPERATOR’S MANUAL.
G Never attempt to make any adjustments while engine
G Read this manual and the tractor Operator’s Manual
carefully. Be thoroughly familiar with the controls and
the proper use of the equipment.
is running.
G Thoroughly inspect the area where the dozer is to be
operated and remove all foreign objects.
G Never allow children to operate the machine. Do not
G Adjust the skid shoe height to clear gravel or crushed
stone surface. See the Adjustments section for pro-
cedure.
allow adults to operate it without proper instruction.
G Do not carry passengers.
G Use only attachments or accessories designed for
your machine. See your dealer for a complete list of
recommended attachments or accessories.
OPERATING SAFETY
G Always clear snow up and down the face of slopes,
never across the face. Exercise extreme caution
when changing direction on slopes. Do not attempt to
clear steep slopes.
G Keep the area of operation clear of all persons, par-
ticularly small children, and pets.
G Never direct discharge towards bystanders.
G Make sure all hardware is secure and that dozer
G Exercise extreme caution when operating on, or
crossing, gravel drives, walks or roads. Stay alert for
hidden hazards or traffic.
blade is in good operating condition.
G Check to be sure all safety devices and shields are in
place.
G After striking an object or if unit starts to vibrate
abnormally, stop the engine and remove the key.
Check for the cause and any damage before restart-
ing. Before any inspection, make sure all moving
parts have stopped.
G Check that all adjustments are correct before using
this unit.
G Gasoline is highly flammable. Follow all precautions
listed in your tractor’s operator’s manual.
G Always wear eye protection while operating and per-
forming adjustments to protect eyes from debris
thrown by the dozer.
G Take all possible precautions before leaving opera-
tor’s position. Lower the attachment, set the parking
brake, stop the engine and remove the key.
G When cleaning, repairing, or inspecting the unit make
sure all moving parts have stopped. Disconnect and
secure the spark plug wires and remove the key to
prevent accidental starting.
G Never operate near glass enclosures, automobiles,
window wells, dropoffs, etc.
G Do not put hands or feet near or under the dozer
blade. Keep clear of the dozer blade at all times.
G Do not overload machine capacity by attempting to
clear too much material at too fast a rate.
DANGER
G Never operate unit at high transport speeds on slip-
pery surfaces. Use care when travelling in reverse.
OPERATING ON SLOPES
CAN BE DANGEROUS
For operation on slopes greater than 15% (8.5°),
weight box, tire chains, and wheel weights are
recommended. NEVER OPERATE ON SLOPES
GREATER THAN 17.6% (10°).
G Never operate the dozer blade without good visibility
or light. Always be sure your feet are properly placed
on the footrests and keep a firm hold on the steering
wheel.
G Do not run the engine indoors.
G Never allow anyone in front of the unit.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
& Controls
CONTROL FUNCTIONS
A
The information below briefly describes the
function of individual controls. Operating the
tractor and dozer require the combined use of
these controls and additional controls whose
operation is described in the tractor Operator’s
Manual.
B
Please take a moment and
familiarize yourself with the
name, location, and function
of these controls so that you
will better understand the safe-
ty and operating instructions
provided in this manual.
Figure 1. Control Locations
A. Blade Angle Control Lever
B. Attachment Lift
A. Blade Angle Control Lever
The blade angle release lever controls a spring-loaded
plate which locks the blade in one of three positions.
Use an abrupt pushing/pulling motion to release the
angling mechanism and move the blade left or right.
Push the angling lever forward fully to lock the blade in
the left position. Pull the lever fully back to lock the
blade in the right position. Move the lever slowly past
center to lock in the centered position.
NOTE: It is easier to change the angle of the blade with
the attachment raised.
B. Attachment Lift
TRACTOR CONTROLS
NOTE: Models with hydraulic or electric lift should refer
to the tractor operator’s manual for lift control informa-
tion.
Before you begin operating the tractor with the dozer
blade attachment, make certain you have:
• Read and understood the instructions in the
tractor Operator’s Manual.
The attachment lift lever raises and lowers the dozer
blade. See the tractor operator’s manual for control
information. See the Adjustments section for proper
attachment lift adjustment.
• Become thoroughly familiar with all of the
tractor controls and their operation, including
how to safely and properly start and stop the
unit.
• Practice driving in an open area—without doz-
ing—to become accustomed to the unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Operating Instructions
Checks Before Starting
WARNING
1. Refer to the Maintenance & Adjustments sections of
this manual and perform any needed service. Also,
refer to the tractor Operator’s Manual and perform
any required service.
Perform the Safety System Interlock test found in
your tractor Operator’s Manual. If tractor does not
pass the test, do not operate the tractor. See your
authorized dealer. Under no circumstances
should you attempt to defeat the safety system.
2. Remove any objects from the work area which might
interfere with plowing activity.
Use caution when plowing a snow covered area.
Snow can cover objects such as curbs, drop-offs,
and other obstacles. Be familiar with the area you
are plowing.
3. Adjust the skid shoes to desired height. See Skid
Shoe Adjustment.
4. Make sure all hardware is present and secure.
To prevent an explosion or fire, never store the
tractor with fuel in the tank inside a building
where an ignition source is present.
Engine & Ground Speed Selection
Always run the engine at full throttle.
Set tractor speed to obtain the needed power to move
the material. Operate at a safe speed, depending on
conditions, so that you have complete control of the trac-
tor. Rear wheel weights and chains are recommended
for slippery surfaces.
IMPORTANT NOTE
To prevent damage to the unit, always
raise the dozer blade BEFORE turning or
backing up.
A weight box is recommended for additional traction.
DANGER
OPERATING ON SLOPES CAN BE DANGEROUS
Transporting
For maximum ground clearance, transport the blade to
and from work areas fully raised and angled straight
ahead.
Never operate on slopes greater than 17.6% (10°)
which is a rise of 3-1/2 feet (106cm) vertically in
10 feet (607cm) horizontally.
Operate the unit at a slow ground speed when
driving onto slope. Avoid using brakes to control
ground speed.
Starting & Stopping
1. Start the tractor engine. Set engine throttle to full.
2. Raise the attachment lift and travel to the work site.
3. Set the angling control to the desired angle.
4. Lower the attachment lift and begin plowing.
5. Raise the plow before backing up.
When operating on slopes that are greater than
15 % (8.5°) but less than 17.6%, use additional
wheel weights or counterweights.
In addition to counterweights, use extra caution
when operating on slopes. Drive UP and DOWN
the slope, never across the face, use caution
when changing directions and DO NOT START
OR STOP ON SLOPE.
6. To stop the tractor, set ground speed to neutral and
set the parking brake. Before leaving the seat, stop
the engine, set the parking brake, remove the key,
and wait for all moving parts to stop.
For additional traction, tire chains and wheel
weights can be added. Maximum weight added to
tractor should not exceed 35 lbs. per wheel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operating Instructions
Changing Angle of the Blade:
Snow Plowing Tips
See Figure 1 for location of Controls.
• Determine the best snow removal pattern before
beginning.
NOTE: It is easier to change the angle of the blade with
the attachment raised.
• Plan the pattern so that you avoid pushing snow onto
cleared areas.
1. Raise the attachment lift.
• When land contour permits, it is best to travel in the
longest direction to minimize turning.
2. Use an abrupt pushing/pulling motion to release the
angling mechanism and move the blade left or right.
Push the angling lever forward fully to lock the blade
in the left position. Pull the lever fully back to lock the
blade in the right position. Move the lever slowly over
center to lock in the centered position.
• In very deep or heavy snow, it may be necessary to
make the first pass with dozer blade partially raised,
then repeat each pass with the blade lowered to clear
the material left on the surface. Also, it may be nec-
essary to clear less than the full width of the dozer
blade or reduce ground speed.
Dozing Tips
• Snow tends to freeze into solid banks when plowed
off a driveway or other large area. Because of this
you may want to plow snow several feet past the
edge of the drive to allow space for future plowing to
build up.
• Determine the best dozing pattern before beginning.
• When land contour permits, it is best to travel in the
longest direction to minimize turning.
• In very deep snow or gravel, it may be necessary to
make the first pass with dozer blade partially raised,
then repeat each pass with the blade lowered to clear
the material left on the surface. Also, it may be nec-
essary to clear less than the full width of the dozer
blade or reduce ground speed.
• If pushing snow past the edges of driveways or side-
walks, be careful not to tear up the grass buried
under snow next to the drive or sidewalk. Lift the
blade several inches off the ground to avoid damag-
ing the grass.
• Spinning tires with tire chains can leave unsightly
marks or permanent damage to asphalt or concrete
driveways or sidewalks. Avoid sudden stops or
starts.
• When dozing, push the dirt to the desired location,
then drag the blade backwards for final leveling. Pack
down the dirt or gravel by driving the tractor over the
leveled area.
• Use any slight grade to your advantage, doze down-
hill, and set the blade angle so that the plowed mater-
ial is moving downhill as it leaves the blade.
Storage
Off-Season Storage
IMPORTANT NOTE
Refer to Tractor Operator’s Manual for
important information concerning safely
storing your tractor.
1. Remove dozer blade and hitch from the tractor.
2. Use water pressure or a brush to thoroughly clean
the dozer blade.
3. Paint, or lightly coat with oil, any area where paint
has been worn or chipped away.
Daily Storage
4. Lubricate the dozer blade.
1. Allow tractor engine to cool before storing in any
enclosure.
5. Store the dozer blade and hitch in a dry place.
2. After dozing or plowing jobs are completed, hose or
brush down the blade to remove excess dirt.
3. Lightly oil all pivot points. Coat bare metal surfaces to
prevent corrosion.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
WARNING
Lubricate Dozer Blade
To avoid serious injury, perform maintenance on
the tractor or dozer blade only when the engine is
stopped, parking brake is set and all moving parts
have stopped. Always remove the ignition key
before beginning maintenance or adjustments to
prevent accidental starting of the engine.
Lubricate the dozer blade as shown in Figure 2. Where
an oil can is shown, wipe the area clean, apply a few
drops of oil (SAE 30), then wipe up drips or spills.
In general, linkage connections and other parts that have
partial rotational or sliding movement should be lubricat-
ed periodically with SAE 30 weight oil. Avoid applying
excessive amounts of oil since this may cause a build-up
of dirt around the lubricated area, making subsequent
lubrication more difficult to accomplish.
Schedule For Normal Care
Care Required
Schedule
Clean debris from
dozer blade.
After each use.
Lubricate dozer blade.
Every 10 hours or at
least once a year.
Figure 2. Lubrication Points
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Skid Shoe Adjustment
Slotted holes are provided to permit adjustment of the
shoe assemblies for raising and lowering the blade to
various working heights (see Figure 3).
When cleaning snow from gravel or earth drives or
walks, the shoe assemblies should be lowered fully to
prevent blade contact with gravel or ground. When
cleaning smooth hard surfaces like concrete, the shoe
assemblies are normally placed fully up to allow the
blade to scrape the surface.
To adjust the skid, raise the blade off the ground and
block with a piece of wood. Loosen the bolts (B, Figure
3) and move the skid shoes (A) up or down to desired
height. Tighten the bolts securely.
Figure 3.
A. Skid Shoes
B. Bolts
Spring Tension
See Figure 4. This snow plow/dozer blade is spring
loaded so that when the blade strikes a solid object, the
springs will allow the blade to release as shown, rather
than cause damage. The blade will go back to its original
position after object is cleared.
Figure 4. Dozer Blade “Released”
See Figure 5. To adjust spring tension hold rear nut (B)
and loosen front nut (E). Tighten rear nut (B) to increase
spring tension, or loosen to decrease tension.
For initial adjustment, tighten nut (B) on each eyebolt
enough to expose about 3/4" (19mm) of thread. Tighten
front nut (E) against rear nut (B) to lock adjustment in
place.
Figure 5. Tension Springs
A. Eyebolt
B. Nut, 5/16
C. Spring
D. Pivot Frame
E. Nut, 5/16
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Lift Rod Adjustment
In the fully raised position the blade should be 6” off the
ground. In the fully lowered position, the lift rod should
slightly compress the spring creating downward pressure
on the blade.
D
C
B
E
NOTE: Always adjust the lift height before and after
adjusting the downward pressure.
A
IMPORTANT NOTE
DO NOT OVER-COMPRESS THE SPRINGS.
In addition to providing downward pressure,
the springs are an elastic medium that
absorbs shocks caused by bumps and
cracks in ground surfaces. Over-compress-
ing the springs defeats this and may cause
damage to the unit.
Figure 6. Adjusting Lift Rod
A. Front Set Collar
B. Rod Guide
C. Spring
D. Rear Set Collar
E. Spring Clip
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
& Assembly
1
4
5
4
3
6
4
2
4
3
8
9
7
10
29
28
11
12
27
2
26
25
22
24
23
10
21
20
19
15
18
17
13
15
14
16
Figure 7. Dozer Components
Ref Qty Description
Ref Qty Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
6
2
4
2
1
1
1
1
3
1
1
1
6
ROD, Control Handle, Upper
16
17
18
19
20
21
22
23
24
25
26
27
28
29
6
2
4
4
2
2
1
2
1
2
2
1
1
2
NUT, Hex, 3/8-16
SKID SHOE
NUT, Hex, 5/16-18
LOCKWASHER, 5/16
WASHER, 5/16
CAPSCREW, 5/16-18 x 1-1/4
ROD, Control Handle, Lower
CLEVIS
WASHER, 1/2
CLIP, Hair Pin
COTTER PIN
WASHER, Plain, 3/8
CAPSCREW, 3/8-16 x 3/4
CAPSCREW, 1/2-13 x 1-1/2
SPACER, 1/2 ID x 3/4 OD x 5/16 LG
ROD, Latch Stop
LOCKNUT, 1/2-13
FRAME ASMY, Dozer
EYEBOLT
SPRING, Extension
CLIP, Hair Pin
PLATE ASMY, Latch
SPRING, Torsion
ROD & PLATE ASMY, Pivot
DOZER BLADE ASMY, 42”
SCRAPER BAR
CARRIAGE BOLT, 3/8-16 x 1
10 LOCKWASHER, 3/8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
2
8
1
7
3
4
18
19
6
5
16
3
21
12
4
16
14
13
20
18
9
8
8
17
15
9
11
10
8
Figure 8. Push Bar, Hitch, & Lift Rod Components
Ref Qty Description
Ref Qty Description
1
2
3
4
5
6
7
8
9
2
2
2
2
1
1
1
5
2
1
1
STOP, Bar
12
13
14
15
16
17
18
19
20
21
1
1
1
1
2
2
2
1
1
1
EYEBOLT, 1/4-20 x 1-1/2
LOCKNUT, Center, 1/4-20
BRACKET, Control Rod
WASHER, 3/8
SCREW, Taptite, 5/16-18 x 1
SETSCREWS, 5/16 x 1/2
SET COLLAR
ROD GUIDE ASSY.
SPRING
ROD, Lift, Electric/Hydraulic
CLIP, Hairpin
CLEVIS PIN
WASHER, 5/16
LOCKNUT, Flange, Whizlock 5/16-18
CAPSCREW, 5/16-18 x 1-1/2
BRACKET, Control Rod
NUT, Hex, Full, 5/16
LOCKWASHER, 5/16
10
11
PUSH BAR ASSY, Front
PIVOT PIN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
Figure 9. Bar Stop
A. Bar Stops
B. Taptite Screws, 5/16-18 x 1
Figure 10. Tension Springs
A. Eyebolt
B. Nut, 5/16
C. Spring
D. Pivot Frame
E. Nut, 5/16
INITIAL SETUP & ASSEMBLY
NOTE: Some of the following setup procedures may
already be completed.
Assemble Blade
1. Place the blade on a flat surface.
2. Install the bar stops (A, Figure 9) using the two 5/16-
18 x 1 taptite screws (B).
3. See Figure 10. Insert threaded end of eyebolt (A)
through lug on blade, and screw on 5/16 nut (B) just
far enough so that it is flush with the end of the eye-
bolt.
4. Hook the springs (C) into the pivot frame (D). Using a
pliers, stretch the springs to hook the opposite ends
to the eyebolts (A).
5. Tighten the nut (B) on each eyebolt enough to expose
about 3/4" (19 mm) of thread.
6. Holding the first nut (B) with a wrench,add a second
nut (E) to each eyebolt, and tighten securely against
the first nut to act as a jam nut.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
Assemble Lift Rod
D
1. Assemble lift rod per Figure 11.
Lift Rod Adjustment
C
Different types of terrain may require an adjustment
to the lift rod assembly. For instructions on how to
make this adjustment refer to the “Lift Rod
Adjustment” procedure in the ADJUSTMENTS sec-
tion of this manual.
B
A
Figure 11. Lift Rod Assembly
A. Set Collars
B. Rod Guide
C. Spring
D. Lift Rod
Install Blade
1. Drive the tractor over the push bar until rear of push
bar is under front hitch.
2. Stop engine, remove key and set parking brake.
3. Raise rear of push bar so its arms fit between lugs of
hitch (A, Figure 12) just behind front axle. Use two
clevis pins (B) and spring clips (C) to secure push bar
to hitch.
4. Insert front of push bar (D) into pivot frame on rear of
blade. Then install king pin (E) down through holes in
hitch and pivot frame. Secure king pin with spring clip
(F).
5. Insert prong of rod guide assembly (H) thru hole in
upright of push bar. Secure with spring clip (I).
6. Connect rear of lift rod (J) to tractor lift arm (K) using
spring clip (G).
Figure 12. Push Bar Installation
A. Tractor Hitch
B. Clevis Pin
C. Spring Clip
D. Push Bar
G. Spring Clip
H. Rod Guide Assembly
I. Spring Clip
J. Lift Rod
E. King Pin
K. Lift Arm
F. Spring Clip
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Assembly
Install Angling Control Rod
NOTE: If installing the dozer attachment on a unit
equipped with a snowcab, replace the control rod sup-
port (A, Figure 13) with the hanging support (Ref. No. 19,
Figure 8). Mount the hanging support to the front cab
cross-bar.
A
B
1. Set the angling control support (A, Figure 13) against
the right side of the frame. Insert two 5/16-18 x 1-1/2
capscrews (C) through the support (A), and frame.
Space the lower hole away from the frame with a
5/16 washer (D). Secure using flange locknuts (E).
C
2. Install the eyebolt (B) in the support (A) and secure
with a centerlock nut.
D
E
Figure 13. Control Rod Support
A. Angling Support
B. Eyebolt & Locknut
D. 5/16 Flatwasher
E. Flange Locknuts
C. 5/16-18 x 1-1/2 Capscrews
3. Connect the lower angling rod (F, Figure 14) to the
dozer release lever using a hair pin clip and washer
(G).
D
C
B
E
4. Insert the upper control rod (C) through the eyelet
(B), and secure the eyelet to the support using a 1/4-
20 centerlock nut (A).
NOTE: It may be necessary to leave the eyebolt nut (A,
Figure 14) loose to prevent binding.
F
5. Secure the upper rod (C) to the lower rod (F) using
two 5/16-18 x 1-1/4 capscrews (D), washers (qty. 4),
lockwashers, and nuts (E). NOTE: Match offset to
offset so the rods form a straight line.
A
G
Figure 14. Assemble Control Rods
A. 1/4-20 Centerlock Nut
B. Eyelet
C. Upper Control Rod
D. 5/16-18 x 1-1/4 Capscrew
E. 5/16 Washers, Lockwashers, & Nuts
F. Lower Control Rod
G. Hair Pin Clip & Washer
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching &
Removing
A
B
D
C
C
E
B
Figure 15. Dozer Removal
A. Support Arm
B. Hair Pin Clip
C. Pivot Pin
D. Hair Pin Clip & Washer
E. Clevis Pins
REMOVAL & INSTALLATION
Removing & Attaching Dozer Blade
1. Lower the blade.
4. Remove the pivot pin (C) connecting the blade and
pushbar. Remove the blade.
2. Remove the hair pin clip and washer (D, Figure 15)
securing the angling control rod to the clevis.
Disconnect the angling control rod.
5. Remove pin (E) securing hitch to the tractor.
8. Reinstall all pins for storage.
3. Remove the angling control rod from the
support arm (A).
Install in reverse order of removal.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Identification & Torque Specifications
Common Hardware Types
Torque Specification Chart
Hex Head Capscrew
FOR STANDARD MACHINE HARDWARE (Tolerance 20%)
Washer
No
Marks
Hardware
Grade
Lockwasher
Carriage Bolt
SAE Grade 2
SAE Grade 5
SAE Grade 8
Hex Nut
Size Of
in/lbs
in/lbs
in/lbs
Hardware ft/lbs
Nm.
2.1
2.3
3.1
3.5
7.6
ft/lbs
Nm.
3.4
3.5
4.9
5.5
10.9
13.6
23.1
25.8
40.8
ft/lbs
Nm.
4.6
4.9
6.8
7.7
16.3
19.0
34.0
34.0
61.2
Standard Hardware Sizing
8-32
8-36
19
20
30
31
43
49
8
10
17
19
30
35
50
55
75
41
43
60
68
12
14
25
27
45
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
27
31
66
76
11
12
20
23
30
35
50
55
65
75
90
100
160
180
140
155
220
240
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
8.6
15.0
16.3
27.2
31.3
40.8
47.6
68.0
74.8
88.4
102.0
122.4
136
217.6
244.8
190.4
210.8
299.2
326.4
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
47.6
68.0
74.8
50
70
80
68.0
95.2
108.8
149.6
163.2
204.0
231.2
299.2
326.4
525.0
571.2
816.0
897.6
102.0
122.4
149.6
163.2
204.0
244.8
353.6
408.0
544.0
598.4
788.8
110
120
150
170
220
240
386
420
600
660
Nut, 1/2”
90
Inside
110
120
150
180
260
300
400
440
580
640
Diameter
7/8-14
1-8
1-12
Screw, 1/2 x 2
900 1,244.0
Body
Diameter
870.4 1,000 1,360.0
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
Body
Length
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Wrench & Fastener Size Guide
1/2
DIA.
7/16
DIA.
3/8
5/16
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16” Bolt or Nut
Wrench—1/2”
3/8” Bolt or Nut
Wrench—9/16”
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2” Bolt or Nut
Wrench—3/4”
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
© Copyright 2000 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|