ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Triple Catcher
Clean Sweep Triple Catcher
Mfg. No.
Description
1695169
Clean Sweep Triple Catcher
1733866
Rev. 04
Rev. Date 12/2006
TP 100-4405-04-AT-SMAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Rules & Information
Normal Removal & Installation
General Warnings............................................2
Collector Installation ......................................10
Safety Decals ..................................................2
Storing the Grass Catcher...............................3
Collector Removal .........................................11
NOTE: In these instructions, “left” and “right” are
referred to as seen from the operating position.
General Operating Information
Before Operation .............................................3
Mowing with the Catcher .................................3
Required Accessories......................................3
After Operation ................................................3
Storing the Grass Catcher...............................3
Initial Installation
Hitch Installation....................................................4
Baffle Installation
Baffle Installation...................................................5
Component Installation
Component Installation..........................................6
Bag and Tube Installation
Bag and Tube Installation......................................8
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules
& Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of
unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-
gle in text signifies important cautions or warnings which must be followed.
GENERAL WARNINGS
• Know the unit’s controls and how to stop quickly.
READ THE OPERATOR’S MANUALS.
• If the mower stalls or the collector chute plugs:
1. Disengage the PTO;
• Read and obey all safety decals.
2. Stop the engine and remove the key;
• Only allow responsible adults, who are familiar with
the instructions, to operate the unit.
3. Set the parking brake, and wait for all moving
parts to stop.
• Disengage the PTO. Shut off the engine and wait for
all moving parts to stop before attaching, adjusting,
or disconnecting any part of the collection system.
• Check the collection system to make sure it is bolted
tightly to the unit.
• DO NOT operate the unit without either the entire
grass catcher or the deflector in place.
• Turn off the PTO to disengage the blades when not
mowing.
• DO NOT mow in reverse unless absolutely neces-
sary. Always look down and behind before and while
travelling in reverse.
• DO NOT turn sharply when travelling alongside a
building or any object. Slow down before turning.
4. Remove the foreign object or clear the chute
with a piece of wood before restarting the engine.
NEVER place hands into COLLECTOR OR
MOWER housing to clear jammed objects.
Blower OR MOWER may rotate when object is
removed.
• For added stability and to prevent tipping or loss of
control:
a. Use reduced speed on uneven ground and
when turning corners.
b. Reduce loads on hillsides. It is recommended
that the collection system be kept only half full
when negotiating any slopes. Start mowing on
slopes when the collection system is empty.
c. Mow up and down the face of slopes; never
across the face of any slope.
• Never operate on slopes greater than 17.6%
• DO NOT carry passengers.
• When collection system is removed from the mower
deck, the deflector must be properly installed.
• Collector bags are subject to deterioration and wear
during normal use. Inspect the bag periodically for
tears, holes, or weak spots and replace with a new
bag that meets manufacturer’s durability standards.
(10°).
SAFETY DECALS
These labels are easily applied and will act as a constant
visual reminder to you, and others who may use the
equipment, to follow the safety instructions necessary for
safe, effective operation.
This unit has been designed and manufactured to pro-
vide you with the safety and reliability you would expect
from an industry leader in outdoor power equipment
manufacturing.
Attachment Decal
Although reading this manual and the safety instructions
it contains will provide you with the necessary basic
knowledge to operate this equipment safely and effec-
tively, we have placed several safety labels on the unit to
remind you of this important information while you are
operating your unit.
WARNING
Thrown objects hazard
• Objects thrown by the mower can seriously
injure or kill you.
• Do not open the hopper while the mower blades
are turning.
All DANGER, WARNING, CAUTION and instructional
messages on your rider, attachments and mower should
be carefully read and obeyed. Personal bodily injury can
result when these instructions are not followed. The
information is for your safety and it is important! The
safety decals below are on your product.
• Do not operate the mower without the complete
catcher in place.
1732819
Decal - WARNING
Thrown Objects Hazard
Part Number 1732819
If any decals are lost or damaged, replace them at once.
See your local dealer for replacements.
Read and obey all operation and warning decals.
TP 600-2562-01-AT-SMA
2
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Operating Instructions
Before Operation
Clear the lawn of all sticks, stones, wire and other debris
which may be caught or thrown by the mower blades.
Check grass condition. If wet, wait until later in the day.
If grass is wet, the grass catcher is likely to become
plugged.
For efficient bagging, air circulation under the
mower deck, through the chute and into the bag is
very important.
For this reason, BEFORE YOU BEGIN MOWING you
should make certain the underside of the mower and
the underside of the catcher lid are free from grass and
debris.
Make sure that there is a snug fit between mower deck,
blower housing, tubes, and grass catcher cover.
Mowing with the Catcher
Always operate with throttle at full speed when mowing.
CAUTION
Before you begin operating the unit be certain
you have read all of the safety and operational
information of this instruction sheet, as well as
the Operator’s Manual for the tractor and any
other attachments.
Grass should be cut often, and not too short. If grass is
too long or lush it may be necessary to keep ground
speed to a minimum or to cut only half the width of the
mower to prevent clogging. If grass is long, operate with
mower in high cutting position for first pass, cutting again
in a lower position on a second pass.
Never operate on slopes greater than 17.6% (10°).
Do not open the cover with mower engaged.
After Operation
Remove any debris from the the screen on the underside
of the lid.
If a large amount of cut grass is spilling out from under
deck, the tube may be plugged or the bags may be full—
discontinue mowing, stop the unit, disengage the PTO,
shut off the engine and then empty the catcher or clear
the tube.
The blower housing and tube should be removed for
cleaning.
Inspect the grass bags for wear or damage. Make sure
that there is a snug fit between mower deck, blower
housing, tubes, and grass catcher cover.
WARNING
ALWAYS shut off the tractor. Disengage the PTO,
and allow all moving parts to stop BEFORE
disconnecting or clearing tube, or emptying
catcher.
CAUTION
Do not leave grass in bagger containers. Empty
containers after each use and before storing.
Failure to do so may result in spontaneous
combustion which could develop into a fire.
Before leaving the operator’s position for any
reason, engage the parking brake, disengage the
PTO, stop the engine and remove the key.
Storing The Grass Catcher
To reduce fire hazard, keep the engine, rider and
mower free of grass, leaves and excess grease.
Do not stop or park rider over dry leaves, grass or
combustible materials.
Clean the grass catcher thoroughly using a mild deter-
gent (other products may damage the tube). Remove
any debris from the the screen on the underside of the
lid.
If paint has been scratched on metal parts, touch up with
paint, or apply a thin film of oil to prevent corrosion.
Store in a dry area. Dry thoroughly before storing for a
long period of time. Always store away from moisture.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial
Installation
B
F
WARNING
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
D
C
C
Initial Installation
A
HITCH INSTALLATION
1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear
frame support (E) through square hole (C) so that the
threaded side (B) is on the inside of tractor.
D
E
2. Secure the 5/16-18 shoulder bolt (D) as shown.
3. Repeat on the other side.
Figure 2. Frame Plate Reinforcement Installation
A. Frame Reinforcement
B. Rear Frame Support
C. Frame Support Hole
B
D. Capscrew, 5/16-18 x 1-1/4 (new)
E. Locknut, 5/16-18 (existing)
F. Capscrew, 5/16-18 (existing)
A
A
C
E
D
A
Figure 1. Install Spacer (left side shown)
A. Speed Nut, 5/16-18
B. Threaded Side
C. Square Hole
D. Shoulder Bolt, 5/16-18
E. Rear Frame Support
D
C
B
4. Remove existing nuts and capscrews from both sides
and rear frame support holes (C, Figure 2)
E
5. Secure frame reinforcement (A) to the inside of the
rear frame support (B) using new 5/16-18 x 1-1/4
capscrews (D) and existing 5/16-18 capscrews and
locknuts (E & F) as shown.
Figure 3. Hitch Installation
A. Hitch
B. Shoulder Bolt
C. Pin
D. Hole in Draw Bar
E. Hair Pin
6. Slide the hitch (A, Figure 3) on right side and left side
shoulder bolt (B) while sliding pin (C) into hole (D) as
shown. Secure with hair pin (E).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Tube Component Assembly
Baffle Installation
1. Determine which baffle to use. See Figure 4 Chart.
44” Mower Deck
50” Mower Deck
“A” RH side 26-1/4” long RH side 29-3/4” long
2. Lift side discharge chute (H, Figure 4).
3. Insert baffle (F) through discharge opening and posi-
tion baffle into place.
“B” LH side 24-7/8” long
LH side 27-3/4” long
4. Tighten carriage bolts (A) and nuts (E) on baffle (F).
5. Tighten carriage bolt (B) and nut (E) on baffle (F).
6. Position baffle (G) into place.
7. Tighten carriage bolts (C) and nuts (E) on baffle (G).
8. Tighten carriage bolts (D) and nuts (E) on baffle (G).
“A”
“B”
H
E
A
A. Carriage Bolts,
5/16-18 x 5/8
B. Carriage Bolt,
E
E
5/16-18 x 5/8
C. Carriage Bolts,
C
F
5/16-18 x 5/8
D. Carriage Bolts,
E
B
D
5/16-18 x 5/8
E
E. Locknut, 5/16-18
F. Right Hand Baffle
G. Left Hand Baffle
H. Discharge Chute
G
Figure 4. Baffle Assembly
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Installation
C
B
A
D
A
C
E
F
B
G
G
H
J
I
Figure 5. Install Mounting Plate
A. Mounting Plate
Figure 6. Lower Chute to Boot Installation
A. Pin, Latch
B. Locknuts, 5/16-18
C. Carriage Bolts, 5/16-18 x 5/8
B. Carriage Bolt, 1/4-20 x 5/8
C. Locknut, 1/4-20
D. Lower Chute
Component Installation
E. Locknut, Center Lock, 5/16-18
F. Strap, Rubber
G. Locknuts, Whiz Lock, 5/16-18
H. Rod, Boot Mount
I. Capscrew, Hex Head, 5/16-18 x 1-1/4
J. Capscrew, Hex Head, Thin, 5/16-18 x 1
INSTALL MOUNTING PLATE
1. Install mounting plate (A, Figure 5) to mower deck as
shown. Secure with 5/16-18 x 5/8 carriage bolts (C)
and 5/16-18 locknuts (A).
LOWER CHUTE ROD AND PIN INSTALLATION
1. Insert the head of pin (A, Figure 6) through front hole
of lower chute (D). Secure with 1/4-20 x 5/8 carriage
bolt (B) and 1/4-20 lock nut (C) as shown.
2. Install the rod (H) to lower chute (D) using 5/16-18 x
1 capscrew (J) and 5/16-18 locknut (G) for front
holes. Use 5/16-18 x 1-1/4 capscrew (I) and 5/16-18
locknut (G) as shown. Tighten hardware.
F
B
A
E
C
3. Install the rubber strap (F) onto capscrew (I) securing
with 5/16-18 locknut as shown.
B
HANDLE INSTALLATION
1. Install handle (A, Figure 7) using 1/4-20 x 1/2 screw
and 1/4-20 locknut (B) for rear hole. Use 1/4-20 x 1
screw (D) as shown. Tighten hardware.
D
Figure 7. Handle to Tube Installation
A. Handle
2. Install strap (E) to screw (D) securing with 1/4-20
locknut (F).
B. Locknuts, KEPS, 1/4-20
C. Screw, Slotted, 1/4-20 x 1/2
D. Screw, Slotted, 1/4-20 x 1
E. Strap, Rubber
F. Locknut, Center Lock, 1/4-20
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Upright Support & Bag Support Bracket
INSTALL UPRIGHT SUPPORT TO HITCH
INSTALL BAG AND COVER SUPPORT
1. Install the upright support (B, Figure 8) to hitch (A)
and secure with 3/8-16 x 1 capscrews (C) and lock-
nuts (D) as shown.
1. Install the bag and cover support (B, Figure 9) to
upright support (A) using reinforcement plate (C) and
3/8-16 x 1 capscrews (D) and 3/8-16locknuts (E) as
shown.
B
B
E
D
C
A
C
D
A
Figure 8. Install Upright Support
A. Hitch
B. Upright Support
C. Capscrews, 3/8-16 x 1
D. Locknuts, 3/8-16
Figure 9. Install Bag and Cover Support
A. Upright Support
B. Bag and cover Support
C. Reinforcement Plate
D. Capscrews, 3/8-16 x 1
E. Locknuts, 3/8-16
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Cover and Bag Installation
INSTALL COVER ASSEMBLY
INSTALL COLLECTOR BAGS
1. Attach cover assembly (B, Figure 10) to bag support
bracket (A) using hinge pivots (E). Secure cover
using cover hinge pins (C) and hair pins (D) as
shown.
1. Raise the cover (A, Figure 11).
2. Attach collector bags (B) using grass bag hanger (C)
to bag hanger post (D).
Note: It may be necessary to fold seat forward to allow
cover to stay in the raised position.
A
C
B
D
E
D
A
C
B
D
E
Figure 11. Install Collector Bags
A. Cover
B. Collector Bags
C
C. Grass Bag Hanger
D. Bag Hanger Post
Figure 10. Install Cover Assembly
A. Bag Support Bracket
B. Cover Assembly
C. Cover Hinge Pins
D. Hair Pins
E. Hinge Pivots
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Tube Installation
D
C
D
C
E
B
A
B
A
Figure 13. Install Upper Tube to Cover
A. Upper Tube
B. Cover
C. Ridge, Upper Tube
D. Ridge Cutout
Figure 12. Install Lower Tube
A. Lower Chute Rod
B. Mounting Plate
C. Rubber Strap
D. Discharge Deflector
E. Locknut
44” Frame Hung Mowers
50” Frame Hung Mowers
44” Free Floating Mowers
LOWER TUBE INSTALLATION
1. Lift discharge deflector up (D, Figure 12).
50” Free Floating Mowers
2. Insert lower chute rod (A) into mounting plate (B).
3. Pull rubber strap (C) and secure by placing hole clos-
est to knob in strap completely over locknut (E).
D
E
F
CONNECTING UPPER & MIDDLE TUBE
1. Slide the upper tube (E, Figure 13) into cover (B)
aligning ridge (C) with cutout (D) as shown.
B
2. See Figure 14 for correct hole location and secure
the upper tube (E) to middle tube using screw (F).
C
2. Slide middle tube (D, Figure 14) into upper tube (E).
3. Slide middle tube (D) over boot (A). Pull strap (B)
and place hole completely over pin (C).
A
Figure 14. Install Middle Tube
A. Lower Chute
B. Strap, Rubber
C. Pin
D. Middle Tube
E. Upper Tube
F. Screw, 1/4 x 3/4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Removal &
Installation
E
F
R
Q
D
C
D
G
A
B
C
P
H
O
A. Hitch Support Assembly J. Deflector
B. Cover
C. Pin
K. Nut & Capscrew
L. Mounting plate
J
N
I
D. Hair Pins
E. Bag
F. Grass Bag Hanger
G. Upper Tube
H. Middle Tube
I. Strap, Boot
M. Lower Chute Rod
N. Lower Chute
O. Pin
P. Strap, Middle
Q. Ridge
K
M
R. Ridge Cutout
L
Figure 15. Normal Installation & Removal
Normal Removal & Installation
4. Lift discharge deflector (J) up. Insert lower chute rod
(M) into mounting plate (L). Pull strap (I) and secure
by placing hole closest to knob in strap completely
over locknut and capscrew (K).
Collector Installation
Note: See previous pages for more detailed installation
and operation instructions if necessary.
5. Slide the upper tube (G) into cover (B) aligning ridge
(Q) with cutout (R) as shown.
1. Mount the hitch support assembly (A, Figure 15) onto
rear tractor frame.
6. Slide middle tube (H) into upper tube (G). Slide mid-
dle tube (H) over lower chute (N). Pull strap (P) and
place hole completely over pin (O).
2. Attach cover (B) to support assembly using pins (C)
and hair pins(D).
3. Pivot cover (B) up. Install bags (E) by attaching
grass bag hanger (F) to support assembly (A).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Removal
Collector Removal
WARNING
OPERATION WITHOUT BAGGER
For operation without bagger, the mower
deflector MUST be properly installed in the down
position and retained by the spring latch.
1. Unhook strap (P, Figure 15) from pin (O). Slide mid-
dle tube (H) into upper tube (G) and remove middle
tube (H). Remove upper tube (G) from cover (B).
2. Lift up cover (B) remove and empty bags (E).
3. Unhook strap (I) from locknut and capscrew (K).
Remove lower chute (N) from mounting plate (L).
See that the discharge deflector (J) returns to the
DOWN position.
4. Remove hair pin (D) and pins (C) then remove cover
(B).
Note: To prevent loss of parts, reinstall pins (C) and hair
pins (D) in support assembly hinge pivots (E, Figure
15).
5. Remove hitch support assembly (A).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURING, INC.
Simplicity Mfg. Inc.500 N Spring
Street / PO Box 997
Simplicity Mfg. Inc.500 N Spring
Street / PO Box 997
Port Washington, WI 53074-0997
Port Washington, WI 53074-0997
Simplicity Mfg. Inc. - Snapper Products
535 Macon Street
Simplicity Mfg. Inc.500 N Spring
Street / PO Box 997
McDonough, GA 30253
Port Washington, WI 53074-0997
Briggs & Stratton Yard Power Products Group
Copyright © 2006 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
|