USER’S MANUAL
SMOOTH AGILE TRAINER
USER WEIGHT LIMITATION: 350lbs(160kgs).
SERIAL NUMBER (found on frame):
Download from Www.Somanuals.com. All Manuals Search And Download.
3
POWER REQUIREMENTS
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE
PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This AGILE Trainer can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges
and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility
of AGILE Trainer damage, always use a surge protector (not included) with your AGILE Trainer.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an
electrical rating 110VAC, 15 amps.
This AGILE Trainer must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for
electric current, should the AGILE Trainer malfunction. This AGILE Trainer is equipped with an electrical cord that has an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge
protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing
below.
GFCI outlets and GFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI Circuit Breakers
may cause this equipment to function improperly.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SMOOTH AGILE TRAINER
SUPPLIED COMPONENTS
This list identifies the major components you will use to assemble this product.
BOX - A
Main Frame Assembly
Handlebar Assembly
BOX - B
Fixed Handlebar
Console Support
Base Frame
UndercarriageCover
[ 719 / 720 ]
Upright-Left
Upright-Right
Pivot Arm Cover
[ 111 ]
[ 110 ]
Download from Www.Somanuals.com. All Manuals Search And Download.
5
SUPPLIED COMPONENTS
This list identifies the major components you will use to assemble this product.
BOX - C
Front Side Panel
[ 712 / 711 ]
[ 709 / 710 ]
BOX - D
Computer
Computer
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SMOOTH AGILE TRAINER
SUPPLIED HARDWARE
This list identifies the hardware you will use to assemble the product. To help distinguish
between the various types of screws and bolts, use the scale below to measure them and
compare them to the sizes listed.
BOX - E
701 Upright Side Cover-Left
717 Pivot Cap 2PCS
702 Upright Side Cover-Right
718 Pivot Side Cap 2PCS
721 Pedal Arm Front Pivot 4PCS
703 Console Back Cover
326 Taper FixingInsert 4PCS
2PCS
2PCS
509
2PCS
2PCS
M6 x 40mm Screw
12 x 62 - M10 x 20mm Bolt
20 x 78 - M14 x 35mm Bolt
501
510
511
12 x 20 x 2 Spring Washer
M10 Nylon Nut
502
503
1PCS
2PCS
8PCS
10PCS
6PCS
M5 x 8mm Screw
512
513
514
4 x 12mm Screw
M8 x 20mm Allen Head Bolt
504
505
506
507
4 x 19mm Screw
2PCS
2PCS
4PCS
2PCS
2PCS
2PCS
M8 x 40mm Allen Head Bolt
M8 x 65mm Allen Head Bolt
M10 x 20mm Allen Head Bolt
12 x 18 x 24.5mm Sleeve
12 x 22 x 2 Washer
M5 x 6mm Bolt
515
516
508
M10 x 62mm Allen Head Bolt
1PCS
A
C
I
B
D
E
F
G
H
Slotted
5mm
Allen key
6mm
Allen key
8mm
Allen key
2.5mm
Allen key
5mm
Allen Wrench
Wrench
Screwdriver-L
(1 piece)
Water Bottle
(1 piece)
Screwdriver
(1 piece)
(1 piece)
(1 piece)
(1 piece)
(1 piece)
(1 piece)
(1 piece)
K
J
Power Cord
(1 piece)
Chest Belt
(1 piece)
MILLIMETERS
Download from Www.Somanuals.com. All Manuals Search And Download.
7
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
100
101
Fixed Handlebar
Crossbar
1
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
Console Support Tube
Base Frame
Main Frame
Pedal Arm-Left
Pedal Arm-Right
Action Handlebar - Left
Action Handlebar - Right
Upright-Left
Upright-Right
Moving Linkage-Left
Moving Linkage-Right
Incline Frame
Incline Transmission Tube-Front
Incline Transmission Tube-Back
Clamp Bracket
Flywheel
Tension Wheel Bracket
Pedal Swing Arm
200
201
202
203
204
205
206
207
208
209
210
211
212
Bearing 6004
4
2
6
4
2
4
8
2
2
1
2
2
Bearing 6005
Bearing 6300
Bearing 6804
Bearing 2203
Bearing 6205
Bearing 608zz
Action Handle Bar Shaft Bushing 2"x38-20
Action Handle Bar Shaft Bushing 2"x38-9
Elector-magnetic System
Oil-Impregnated Bearing
Clamp Bushing- Top
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SMOOTH AGILE TRAINER
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
213
Clamp Bushing- Bottom
Belt
2
214
215
216
217
218
219
220
221
222
224
225
226
227
228
229
230
231
232
233
234
235
238
239
240
241
242
243
244
249
250
251
1
1
1
1
1
2
2
2
1
2
2
2
2
2
1
1
1
2
2
1
1
2
1
1
4
4
3
1
1
9
2
Aluminum Disk
Crank
Crank 25x186.7
Crank Disk Axle
Wheel
Pedal Buffer Set
Level Adjuster
Crank Disk
Action Handle Bar End Cap
Hand Pulse Sensor Cover
Oval Tube Cap
Hand Pulse Sensor Back Cover
Fixed Handlebar Foam Grip
Electro-magnetic System Bracket
Flywheel Axle Fixing Plate
Speed Sensor Base
Pedal Support Base
Pedal Fixing Base
Crank Disk Oval Cap
Switch Fascia
Bearing 2201
5/16" Cable Tie
1/8" Cable Tie
3/8" Cable Tie
Wheel Bushing
Bearing 6000
Self-adhesive Wire Clip
3/16" Cable Tie
1/4" Cable Tie
Hand Grip Gasket
300
302
303
304
305
Rear Shroud-Left
1
1
1
1
Rear Shroud-Right
Rear Side Panel-Left
Rear Side Panel-Right
Download from Www.Somanuals.com. All Manuals Search And Download.
9
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
336
337
338
339
340
341
Switch Plate
1
2
2
2
2
2
1
1
1
4
4
4
2
2
4
2
1
4
1
2
35
1
2
2
2
2
22
7
4
2
2
2
1
3
Pedal
Toe Cap
Pedal Soft Cushion
Pedal Bushing Cover-Left
Pedal Bushing Cover-Right
Console Housing - Upper
Console Housing – Bottom
Console Plastic Cover
Rubber Strip-4
Rubber Strip-3
Rubber Strip-2
Rear Shroud Plug-1
Rear Shroud Plug-2
Rubber Strip-1
Cable Plug
Incline Transmission Tube Holder
Moving Linkage Bushing
Control Board Cover
Pedal Swing Arm Cap
Taper Fixing Insert
Support Lump
Oblong Cushion
Circular Cushion
Rubber Cushion – Front
Rubber Cushion – Rear
Fixing Insert
Fixing Insert-Metal Inside
Action Handlebar Bar Front Cover
Action Handlebar Bar Cover
Elbow-Left
Elbow-Right
Button
Taper Fixing Insert-Metal Inside
Download from Www.Somanuals.com. All Manuals Search And Download.
10
SMOOTH AGILE TRAINER
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
400
401
Fix Bolt
2
2
7
11
23
2
4
1
1
2
2
2
6
2
2
2
4
4
8
3
3
2
2
2
1
2
1
4
2
8
1
402
403
404
405
406
407
408
409
410
411
412
414
415
416
417
418
419
421
422
423
424
425
426
427
428
429
430
431
432
433
25 x 10 x 55 - M10 x 15mm Bolt
M5 x 8mm Allen Head Bolt
M6 x 12mm Allen Head Bolt
M8 x 15mm Allen Head Bolt
M8 x 25mm Allen Head Bolt
M10 x 20mm Allen Head Cap Bolt
M10 x 40mm Allen Head Bolt
M4 X 40mm Allen Head Cap Bolt
M8 x 50mm Allen Head Cap Bolt
M10 x 40mm Allen Head Cap Bolt
M12 x 70mm Allen Head Cap Bolt
M8 x 20mm Bolt
M3 x 8mm Screw
M8 x 65mm Allen Head Cap Bolt
M6 x 12mm Allen Head Cap Bolt
M8 x 16mm Allen Head Cap Bolt
M8 x 90mm Allen Head Bolt
M8 Nylon Nut
M10 Nylon Nut
M14 Nylon Nut
M8 Blind Nut
M6 x 15mm Screw
3/4" x 16 Nut
Flywheel Axle
10 x 36mm Shaft
12 x 210 - M14 x 70mm Shaft
Bushing 12 x 60
M4 x 15mm Screw
4 x 12mm Screw
Action Handlebar Shaft
Download from Www.Somanuals.com. All Manuals Search And Download.
11
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
456
457
458
459
460
Pedal Arm Support Axle
Crank Axle Bushing
M10 C Clip
2
2
6
M12 C Clip
2
M42 C Clip
2
10 x 18 x T1.0 Fiber Washer
15 x 8 x T2.0 Spring Washer
10 x 16 x T2.0 Spring Washer
20 x 6 x T2.0 Washer
32 x 6 x T2.0 Washer
35 x 14 x T2.0 Washer
10 x 18 x T5.1 Washer
M3 x 8mm Screw
2
11
7
3
1
2
4
2
M3 x 10mm Screw
4 x 12mm Screw
18
47
8
M2 x 6mm Screw
4 x 12mm Screw
23
2
M32 C Clip
M4 x 45mm Screw
M4 x 8mm Screw
2
4
7 x 12 - M5 x 5mm Pin Nut
10 x 23 x T2.0 Washer
6 x 10 x 1 Spring Washer
28.6 x 35.5 Bushing
12 x 20 x 0.5 Washer
12 x 20 x 2 PU Washer
4
4
2
2
2
2
500
501
502
503
504
505
506
507
508
12 x 62 - M10 x 20mm Bolt
20 x 78 - M14 x 35mm Bolt
M5 x 8mm Screw
2
2
2
8
2
2
4
1
M8 x 20mm Allen Head Bolt
M8 x 40mm Allen Head Bolt
M8 x 65mm Allen Head Bolt
M10 x 20mm Allen Head Bolt
M10 x 62mm Allen Head Bolt
Download from Www.Somanuals.com. All Manuals Search And Download.
12
SMOOTH AGILE TRAINER
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
509
M6 x 40mm Screw
12 x 20 x 2 Spring Washer
M10 Nylon Nut
2
2
510
511
512
513
514
515
516
1
4 x 12mm Screw
10
6
4 x 19mm Screw
12 x 18 x 24.5mm Sleeve
12 x 22 x 2 Washer
M5 x 6mm Bolt
2
2
2
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
626
Speed Sensor
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
2
2
2
1
1
Magnetic Sensor
Power Switch
Power Breaker
Power Insert Set
Receiver
Transformer
Computer PC Board
Elevation Motor
Control Board
Button Sticker
Overlay
Elector-magnetic Wire
Power Connect Wire
8Pin Power Wire-Top 200mm
8Pin Power Wire-Upper 1000mm
8Pin Power Wire-Middle 900mm
8Pin Power Wire-Lower 800mm
8Pin Power Wire-Bottom 2700mm
3C Power Wire 1000mm
Hand Pulse Sensor Wire-Top 350mm
Hand Pulse Sensor Wire-Upper 620mm
Hand Pulse Sensor Wire-Lower 650mm
Receiver Wire 350mm
Control Board Connect Wire 250mm
Download from Www.Somanuals.com. All Manuals Search And Download.
13
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
700
701
Upright Side Cover-Left
Upright Side Cover-Right
Console Back Cover
Pivot Arm Cover-LL
Pivot Arm Cover-LR
Pivot Arm Cover-RR
Pivot Arm Cover-RL
Pivot Arm Insert
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
2
1
1
4
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
Front Side Panel-LL
Front Side Panel-LR
Front Side Panel-RR
Front Side Panel-RL
Front Side Frame-LL
Front Side Frame-LR
Front Side Frame-RR
Front Side Frame-RL
Pivot Cap
Pivot Side Cap
Undercarriage Cover-Left
Undercarriage Cover-Right
Pedal Arm Front Pivot Cover
A
B
C
D
E
F
G
H
I
Screwdriver-L
2.5mm Allen Key
5mm Allen Key
6mm Allen Key
8mm Allen Key
14 x 17 Wrench
Slotted Screwdriver
5mm Allen Wrench
Water Bottle
1
1
1
1
1
1
1
1
1
1
1
J
Power Cord
K
Chest Belt
Download from Www.Somanuals.com. All Manuals Search And Download.
14
SMOOTH AGILE TRAINER
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
703
224
326
101
509
424
321
228
450
608
314
208
449
447
504
321 208
102
433
313
450
340
611
312
612
Download from Www.Somanuals.com. All Manuals Search And Download.
15
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
505
447
227
326
251
432
225
103
225
251
338
326
227
447
336
209
339
336
701
336
432
506
339
338
432
336
201
448
416
504
448
506 702
201
448
448
209
504
337
108
721
110
501
510
451
514
112
109
337
113
416
111
514
238
451
504
515
515
510
238
326
320
513
332
501
721
332
513
326
315
504
320
316
317
332
709
512
315
316
513
710
326
447
332
332
713
513
317
712
714
513
326
332
711
447
716
715
512
513
Download from Www.Somanuals.com. All Manuals Search And Download.
16
SMOOTH AGILE TRAINER
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
308
309
308
309
404
406
404
450
406
307
307
450
331
330
232
331
405
232
414
326
421
220
419
405
330
220
207
204
310
448
414
207
421
421
421
207
311
448
430
419
502
448
430
310
437
204
233
459
233
721
459
721
107
502
460
323
323
323
437
460
417
457
326
442
438
205
405
106
405
311
205
448
438
442
457
417
Download from Www.Somanuals.com. All Manuals Search And Download.
17
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
423
444
458
717
503
718
503
717
206
206
120
206
458
206
444
407
441
456
423
516
117
212
248
407
441
421
429
423
456
325
511
325
508
117
245
212
245
412
247
213
229
412
246
248
210
410
442
439
427
405
440
114
211
215
118
243
439
247
213
436
246
322
418
115
116
440
403
404
440
436
243
405
440
418
230
327
425
405
440
234
422
221
441
441
435
202
609
408
222
214
226
221
226
426
216
434
404
405
440
411
434
404
443
441
411
414
218
202
435
217
426
602
431
Download from Www.Somanuals.com. All Manuals Search And Download.
18
SMOOTH AGILE TRAINER
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
704
450
708
705
436
326
512
428
242
436
401
219
401
436
448
428
242
450
250
512
707
708
450
326
448
326
512
329
448
409
706
512
403 119
448 240
719
448
328
219
436
512
104
445 203 445
402
422
326
507
326
318
329
448
450
319
448
448
244
328
607
446
448
241
239
341
601
231
512
448
720
448
250
332
324
333
241
454
249
448
448
105
452
453
610
318
448
306
304
603
302
235
319
403
415
332
604
605
403
448
303
305
Download from Www.Somanuals.com. All Manuals Search And Download.
19
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
615
623
621
615
624
626
623
616
606
340
623
617
622
620 607 609
619
617
601
613
618
613
620
619
620
619
613
620
614
614
Download from Www.Somanuals.com. All Manuals Search And Download.
20
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 1: Connect the Main Frame to Base Frame
(A) Rotate Incline Frame (114) up to vertical position.
(B) Place cardboard block under Main Frame tube to provide clearance to
position Base Frame (104) for assembly.
507
X4
(C) Position Base Frame (104) under mounting bracket of the Main Frame
(105) and align the 4 hole bolt pattern.
(D) Remove cardboard block and lower Main Frame (105) onto Base Frame
(104). Mounting Brackets should seat fully onto Base Frame (104). Secure
using four (4) M10 x 20mm Allen Head Bolts (507).
114
104
c
A
B
507
618
114
619
104
Mounting Brackets
105
Download from Www.Somanuals.com. All Manuals Search And Download.
21
ASSEMBLY
STEP 2: Connect the Incline Transmission Tube
(A) Remove the Incline Transmission Tube Holder (322), and discard.
508 X1
511 X1
(B) Rotate the Incline Frame (114) to align the bolt holes with the mating bolt
holes in the Incline Transmission Tube-Front (115).
(C) Assemble the Incline Transmission Tube-Front (115) to the Base Frame
(104) with M10 x 62mm Allen Head Bolt (508) and M10 Nylon Nut (511)
by 6mm Allen Key (D) and Wrench (F).
(D) Connect the 8Pin Power Wire-Lower (618) to the 8Pin Power Wire
-Bottom (619) , and fixed the wire into the Self-adhesive Wire Clip (244).
115
105
114
FIG2
D
508
115
F
511
104
332
619
244
618
114
FIG1
Download from Www.Somanuals.com. All Manuals Search And Download.
22
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 3: Assemble the Undercarriage Covers
NOTE：THE UNDERCARRIAGE COVER-LEFT(719) FITS OVER THE 8PIN
POWER WIRE-LOWER (618). BE CAREFUL NOT TO DISCONNECT
THE WIRE WHEN ASSEMBLING THE UNDERCARRIAGE COVER
-LEFT (719).
512 X4
(A) Lift the Pedal Arm and assemble the Undercarriage Cover-Left (719) to the
Base Frame (104), and secure using four 4 x 12 Screws (510).
(B) Repeat the above procedure to assemble the right side.
107
512
105
106
512
720
104
719
618
Download from Www.Somanuals.com. All Manuals Search And Download.
23
ASSEMBLY
STEP 4: Assemble the Upright
NOTE: 1. DO NOT TIGHTEN THE M8 x 20mm ALLEN HEAD BOLT WHEN
YOU ASSEMBLE THE UPRIGHT TO THE BASE FRAME.
(A) Assemble the Upright-Left (110) and Upright-Right (111) to the Handlebar
assembly and secure using two M8 x 56mm Allen Head Bolts (506).
Do not completely tighten M8 x 56mm Allen Head Bolts until step C.
504 X4
506 X2
(B) Insert the Upright Assembly to the Base Frame (104) and secure with four
M8 x 20mm Allen Head Bolts (504).
(D) Tighten the M8 x 56mm Allen Head Bolt (505).
(C) Connect the 8Pin Power Wire-Lower (618) to the 8Pin Power Wire-Middle
(617).
506
111
109
102
108
110
506
110
111
504
504
504
104
617
618
Download from Www.Somanuals.com. All Manuals Search And Download.
24
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 5: Attach the Pivot Arm Covers
(A) Thread the free end of the Pedal Swing Arm (120) through the hole in
the Pivot Arm Cover-RL (707) and manuver the Pivot Arm Cover-RL
(120) to it’s final upright position. See the illustrations in STEP1, STEP2,
and STEP3.
512
X4
(B) Assemble the Pivot Arm Cover-RR (706) and the Pivot Arm Cover (707)
using the press-fit pins and secure to the frame using two 4 x 12mm
Screws (512).
(C) Repeat the above procedure to assemble the left side.
STEP1
120
707
STEP2
707
120
706
707
705
704
120
STEP3
707
512
120
512
512
114
Download from Www.Somanuals.com. All Manuals Search And Download.
25
STEP 6: Assemble the Pivot Cap
503
X2
NOTE: ALIGN THE 3 SNAP FIT TABS ON THE PEDAL SIDE CAPS (718)
WITH THE 3 SPAP FIT ON THE PEDAL CAPS (717).
717
718
X2
X2
(A) Assemble the Pivot Cap (717) to the Pedal Swing Arm (120) and secure
using the M5 x 8mm Screw (503).
(B) Press the Pedal Side Cap (718) to the Pedal Cap (717).
717
503
717
503
718
503
717
120
Download from Www.Somanuals.com. All Manuals Search And Download.
26
SMOOTH AGILE TRAINER
STEP 6: Assemble the Console Support Tube
NOTE: INSERT BOTH ENDS OF THE CONSOLE SUPPORT TUBE-FRONT
AT THE SAME TIME.
504
X2
(A) Connect the 8Pin Power Wire-Upper (616) to the 8Pin Power Wire-Middle
(617).
(B) Assemble the Consol Support Tube (103) to the Upright and Secure using
the M8 x 20mm Allen Head Bolt (504).
616
103
FIG 1
616
617
616
617
110
111
110
504
Download from Www.Somanuals.com. All Manuals Search And Download.
27
ASSEMBLY
STEP 8: Assemble the Fixed Handlebar
(A) Assemble the Fixed Handlebar (101) to the Console Support Tube (103)
and Crossbar (102).
504 X2
505 X2
(B) Secure the Fixed Handlebar (101) to the Crossbar (102) with two
M8 x 20mm Allen Head Bolts (504).
(C) Secure the Fixed Handlebar (101) to the Console Support Tube (103)
with two M8 x 40mm Allen Head Bolts (505).
101
103
505
101
102
103
504
102
Download from Www.Somanuals.com. All Manuals Search And Download.
28
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 9: Tighten all Bolts
(A) Tighten the M8 x 65mm Allen Head Cap Bolt by 6mm Allen Key (D) as show in STEP1.
(B) Tighten the M8 x 20mm Allen Head Bolt (504) by 5mm Allen Key (C) as show in STEP2.
(C) Tighten the Fix Bolt (401) by 5mm Allen Key (C) as show in STEP3.
STEP 1
STEP1
D
416
STEP 2
504
C
STEP 3
401
STEP 3
STEP 2
C
Download from Www.Somanuals.com. All Manuals Search And Download.
29
ASSEMBLY
STEP 10: Assemble Upright Side Covers
701
702
X1
X1
(A) Press the Upright Side Cover-Left (701) and Upright Side Cover-Right
into the Upright sides.
701
110
702
111
Download from Www.Somanuals.com. All Manuals Search And Download.
30
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 11: Connect the Pedal Arm to the Pedal Swing Arm
(A) Slide the 20 x 78-M14 X 35mm Bolt (502) through the Pedal Arm-Right
(107) and Pedal Swing Arm (120) the secure by 8mm Allen Key (E).
502 X2
(B) Repeat the above procedure to assemble the left side.
120
107
502
E
Download from Www.Somanuals.com. All Manuals Search And Download.
31
ASSEMBLY
STEP 12: Connect the Moving Linkage
501 X2
510 X2
514 X2
(A) Connect the Action Handlebar-Right (109) to the Moving Linkage-Right
(113) and secure using the 12 x 62-M10 x 20mm Bolt (501), 12 x 2 x 2mm
Spring Washer (510), 12 x 22 x 2mm Washer (515), and 12 x 18 x 24.5
Sleeve (514) by 6mm Allen Key (D), as show in FIG1.
(B). Repeat the above procedure to assemble the left side.
515 X2
FIG 1
510
D
109
113
514
113
515501
514
515
510
501
D
Download from Www.Somanuals.com. All Manuals Search And Download.
32
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 13: Assemble the Pedal Arm Front Pivot Covers
(A) Press the Pedal Arm Front Pivot Cover (721) into the ends of the Action
Handlebar-Right (109) and Pedal Arm-Right (107).
721
X4
(B) Repeat the above procedure on the left side.
108
109 107
721
721
Download from Www.Somanuals.com. All Manuals Search And Download.
33
ASSEMBLY
STEP 14: Tighten Set Screws
(A) Secure the M5 x 6mm Screw (516) to the Pedal Swing Arm (120) using the
2.5mm Allen Key (B).
516 X2
B
516
106 120
120
B
516
Download from Www.Somanuals.com. All Manuals Search And Download.
34
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 15: Assemble the Front Side Panels
NOTE: THERE ARE 3 HOLES IN THE FRAME COMPONENTS THROUGH
WHICH THE INSIDE AND OUTSIDE PLASTIC PANELS CONNECT
TO EACHOTHER. USE THESE HOLES AS REFERENCES TO
CORRECTLY POSITION THE PLASTIC PANELS.
512 X2
513 X6
(A) Assemble the Front Side Panel-LL (709) and Front Side Panel-LR (710)
to the left Upright and secure using one 4 x 12 Screw (512) and three
4 x 19mm Screws (513).
(B) Repeat the above procedure to assemble the right side.
111
Reference hole1
110
710
513
513
512
Reference hole3
711
712
513
513
512
709
Reference hole2
Download from Www.Somanuals.com. All Manuals Search And Download.
35
ASSEMBLY
STEP 16: Assemble the Console
NOTE: BE SURE TO PUSH THE WIRES INTO THE CONSOLE BEFORE
YOU SECURE TO THE FRAME.
509
X2
(A) Connect the 8Pin Power Wire-Top (615) to the 8Pin Power Wire-Upper (616)
as show in FIG1.
(B) Assemble the Computer (312) to the Console Support Tube-Front (103) and
secure using two M6 x 40mm Screws (509).
(C) Connect the Hand Pulse Sensor Wire-Upper (622) to Computer (312) as
show in FIG2.
FIG 1
615
616
312
103
509
FIG 2
312
622
Download from Www.Somanuals.com. All Manuals Search And Download.
36
SMOOTH AGILE TRAINER
ASSEMBLY
STEP 17: Assemble Console Back Cover
(A) Assemble the four Taper Fixing Inserts (326) to the Console Back Cover
(703).
326 X4
(B) Assemble the Console Back Cover (703) to the Computer (312).
312
326
703
Download from Www.Somanuals.com. All Manuals Search And Download.
37
LEVEL ADJUSTMENT
LEVEL ADJUSTMENT:
To adjust the levelers follow these instructions:
You will need someone to help you with this procedure, as you will need to tip, the AGILE Dynamic Motion Trainer
while adjusting the levelers
Tip the AGILE Dynamic Motion Trainer to the left/right. You will then see the LEVEL ADJUSTERS. These will need to
be screwed either in or out to level the trainer. Repeat for the other side. It may help to use a bubble level when
adjusting the level on your AGILE Dynamic Motion Trainer.
LEVEL ADJUSTMENT
SERIAL NUMBER LOCATION
Download from Www.Somanuals.com. All Manuals Search And Download.
38
SMOOTH AGILE TRAINER
LITE-TOUCH CONTROL OPERATION
LITE-TOUCH CONTROL:
The Intensity Level and Motion Level can be controlled using the Lite-Touch controls on the hand grips of the
action handlebars. As the illustration indicates, the right Lite-Touch Controller controls the Motion Level and the
left Lite-Touch Controller controls the Intensity Level. You can see the corresponding readouts on the console
follow this same orientation.
To use the Lite-Touch Controls, simply start a program or select START and begin your work out. To increase
either the Motion Level or the Intensity Level, move your thumb to the thumb groove with the “+” indicator. If you
hold your thumb in the thumb groove the level will continue to increase until you remove your thumb. To decrease
the level simply place your thumb in the groove marked with the “-“ indicator.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
TRANSPORT INSTRUCTION
TRANSPORT INSTRUCTIONS:
To transport your AGILE Dynamic Motion Trainer simply lift the back end and roll it away to the desired location, as
shown.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
SMOOTH AGILE TRAINER
MUSCLE CHART
Targeted muscle groups:
The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle groups
are shown in gray color on the chart below.
MUSCLE GROUPS
A
B
C
D
E
F
Shoulder muscles
Pectoral muscles
Bicep muscle
Calf muscles
Trapezius muscles
Tricep muscles
G
H
I
Abdominal muscles
Forearm muscles
Quadricep muscles
Back muscles
J
K
L
Gluteal muscles
Hamstring muscles
Download from Www.Somanuals.com. All Manuals Search And Download.
41
STRETCHING ROUTINE
Warm up and cool down:
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and
preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four
or five times per week.
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to
your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the warm-up and
cool-down exercises on the following pages:
Toe Touch:
Shoulder Lift:
Slowly bend forward from
your waist, letting your back
and shoulders relax as you
stretch toward your toes.
Reach down as far as you
can and hold for 15 counts.
Lift your right shoulder up
toward your ear for one
count. Then lift your left
shoulder up for one count as
you lower your right shoulder.
Inner Thigh Stretch:
Hamstring Stretch:
Sit with the soles of your feet
together with your knees
pointing outward. Pull your
feet as close into your groin
as possible. Gently push
your knees towards the floor.
Hold for 15 counts.
Sit with your right leg
extended. Rest the sole of
your left foot against your
right inner thigh. Stretch
toward your toe as far as
possible. Hold for 15 counts.
Relax and then repeat with
left leg extended.
Side Stretch:
Calf-Achilles Stretch:
Open your arms to the side
and continue lifting them until
they are over your head.
Reach your right arm as far
upward toward the ceiling as
you can for one count. Feel
the stretch up your right side.
Repeat this action with your
left arm.
Lean against a wall with your
left leg in front of the right
and your arms forward. Keep
your right leg straight and the
left foot on the floor; then
bend the left leg and lean
forward by moving your hips
toward the wall. Hold, and
then repeat on the other side
for 15 counts.
Head Roll:
Rotate your head to the right
for one count, feeling the
stretch up the left side of your
neck. Next, rotate your head
back for one count, stretching
your chin to the ceiling and
letting your mouth open.
Rotate your head to the left
for one count, and finally,
drop your head to your chest
for one count.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
SMOOTH AGILE TRAINER
COMPUTER OPERATION
I
A
J
B
C
D
K
E
L
M
F
G
H
N
DTAT DISPLAY-1
DTAT DISPLAY-2
MOTION LEVEL
A
B
I
INTENSITY LEVEL
J
INTENSITY PROFILE
PROGRAMS
MOTION PROFILE
INTENSITY-UP
START
C
D
E
F
K
L
EXPRESS MOTION
INTENSITY-DOWN
STOP / ENTER
M
N
MOTION-UP
G
H
MOTION-DOWN
Download from Www.Somanuals.com. All Manuals Search And Download.
43
COMPUTER OPERATION
DISPLAY FUNCTIONS:
There are 6 display areas to show all the necessary information prior to and during the workout.
INTENSITY LEVEL DISPLAY:
Displays intensity level from 1 to 20.
8 x 16 DOT MATRIX INTENSITY LEVEL PROFILE DISPLAY:
Displays all operating instructions prior to the workout and displays intensity level profiles during the workout.
8 x 8 DOT MATRIX MOTION LEVEL PROFILE DISPLAY:
Displays motion level profiles during the workout.
MOTION LEVEL DISPLAY:
Displays motion levels from 1 to 12.
DATA DISPLAY 1:
Prior to using a preset program, data display 1 displays and allows user to set age, workout time and target heart rate.
During the workout, data display 1 displays TIME, RPM or PULSE depending on which display mode is selected. Scan mode
can also be selected to view all available data.
DATA DISPLAY 2:
Prior to using a preset program, data display 2 displays and allows user to set weight, distance target, calorie target or watt
target.
During the workout, data display 2 displays DISTANCE, CALORIES or WATTS depending on which display mode is selected.
Scan mode can also be selected to view all available data.
DISPLAY MODES:
Mode 1: Scan mode (scans through display modes 2-4)
Mode 2: TIME and DISTANCE
Mode 3: RPM and CALORIES
Mode 4: PULSE and WATTS
COMPUTER OPERATION:
POWER ON:
Plug in the POWER CORD and set the power switch to ON. All the LED windows will light up and begin scanning. The
INTENSITY LEVEL Dot Matrix displays and begins scrolling “SELECT-QUICK-START-OR-PROGRAM”. The other LED
windows will show the factory settings as follows:
INTENSITY LEVEL window display: “1”
MOTION LEVEL window display: “1”
DATA DISPLAY-1: displays (default AGE): ”35”, AGE LED light on.
DATA DISPLAY-2: displays (default WEIGHT): “150” lb, WEIGHT LED light on.
During the workout, press the STOP button twice to return to POWER ON status.
SLEEP MODE:
The computer will automatically enter SLEEP MODE if left idle for 3 minutes without any input in POWER ON status. When
the computer is in SLEEP MODE, press any button or pedal and the machine will return to POWER ON status. You can turn
SLEEP MODE off but the console will be drawing power indefinitely if it is plugged in to keep the LEDs lit. To turn SLEEP
MODE off, get the console to POWER ON status then press INTENSITY UP and DOWN buttons and hold for 5 seconds.
Data display 2 will show “1”. Press the START button and data display 2 will display the SLEEP MODE status. To toggle
between “On” and “Off”, select INTENSITY UP or DOWN then press STOP/ENTER to confirm and return to POWER ON
status.
PAUSE/STOP:
During the workout, press the STOP button or stop pedaling for 10 seconds to enter PAUSE status. The INTENSITY LEVEL
Dot Matrix display will show “PAUSE”. All the figures on the console will be frozen. Press the START button or start pedaling
to resume the program and all the displays will
Download from Www.Somanuals.com. All Manuals Search And Download.
44
SMOOTH AGILE TRAINER
COMPUTER OPERATION
continue the performance until the program finishes. If you leave the pedal stopped for over 3 minutes or press the STOP
button twice, all the data will return to 0 and the computer will return to POWER ON status.
ENGLISH/METRIC CONVERSION:
The console display can show ENGLISH and METRIC information. The factory should have the proper setting on this for the
different markets. In case it needs to be converted between METRIC and ENGLISH readout, please follow the procedure
below:
1.Set the POWER SWITCH to ON. Press both the STOP and MOTION UP button at the same time and hold for 3 seconds.
The INTENSITY LEVEL Dot Matrix will display and scrolling “KM” or “ML”. KM is displayed for METRIC and ML for ENGLISH.
2. Press the INTENSITY UP/DOWN button to switch between Metric and English then pressing STOP/ENTER to save the
setting and return to Power On status.
SOUND on/off:
From the POWER ON status press and hold INTENSITY UP and DOWN buttons for 5 seconds to get to the
display control mode. The data display 2 will be displaying “1”. Press INTENSITY UP once so that “2” is
displaying then press the START button. To toggle between sound “on” or “off” use the INTENSITY UP or
DOWN button then press STOP/ENTER to confirm and return to POWER ON status.
PROGRAM OPERATING INSTRUCTION
QUICK START:
When the console is in POWER ON status, press the START button to activate the QUICK START program. The Intensity
Level Display shows “1” and the INTENSITY LEVEL Dot Matrix displays the intensity level profile. The Motion Level Display
shows “1” and the MOTION LEVEL Dot Matrix displays motion level profile. Press the INTENSITY UP/DOWN button to
change the intensity level. Press the MOTION UP/DOWN button to change the motion level. The TIME, CALORIES and
DISTANCE will count up from 0.
TARGET PROGRAM:
When the console is in POWER ON status, press the TARGET program button once to enter the TARGET TIME program set
up:
Press TARGET program button twice to enter the TARGET DISTANCE program set up,
Press TARGET PROGRAM button three times to enter the TARGET CALORIES program set up
Continue the rotation among these three target programs by pressing the TARGET program button.
Target Time:
Press the TARGET program button once to get to the TARGET TIME program, then press STOP/ENTER to enter the set up
procedure.
TIME display shows the factory default setting “30:00” . Press INTENSITY UP/DOWN button to adjust the target time and
press STOP/ENTER to confirm.
AGE display shows factory default setting “35” . Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the target time program. Time counts down to 0, Distance and Calories count up. Press
INTENSITY UP/DOWN to adjust the resistance and press MOTION UP/DOWN to adjust the motion.
Target Distance:
Press the TARGET program button twice to get to the TARGET DISTANCE program then press STOP/ENTER to enter the
set up procedure.
DISTANCE display shows factory default setting “5.00”. Press INTENSITY UP/DOWN button to adjust the target distance and
press STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
COMPUTER OPERATION
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the target distance program. Distance counts down to 0, Time and Calories count up. Press
INTENSITY UP/DOWN to adjust the resistance and press MOTION UP/DOWN to adjust the motion.
Target Calories:
Press the TARGET program button three times to get to the TARGET CALORIES program, then press
STOP/ENTER to enter the set up procedure.
CALORIES display shows factory default setting “50”. Press INTENSITY UP/DOWN button to adjust the target
calories and press STOPE/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the target distance program. Distance counts down to 0, Time and Calories count up. Press
INTENSITY UP/DOWN to adjust the resistance and press MOTION UP/DOWN to adjust the motion.
FAT BURNING PROGRAM
When the console is in POWER ON status, press the FAT BURNING program button then press STOP/ENTER
to continue the set up procedure.
TIME display shows factory default setting “30:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the FAT BURNING program. Time counts down to 0, Distance and Calories count up. Dot Matrix
display shows the pre-set INTENSITY and MOTION profile. Press INTENSITY UP/DOWN to adjust the resistance and press
MOTION UP/DOWN to adjust the motion.
INTERVAL PROGRAM
When the console is in POWER ON status, press the INTERVAL program button once to select the INTENSITY INTERVAL
program then press STOP/ENTER to enter the program set up procedure.
OR
Press INTERVAL program button twice to select the MOTION INTERVAL program then press STOP/ENTER to enter the
program set up procedure.
Continue the rotation between these two INTERVAL programs by pressing the INTERVAL program button.
Intensity Interval Program
When the console is in INTENSITY INTERVAL program set up, INTENSITY LEVEAL DISPLAY shows “L1”. This indicates the
intensity level for the intervals. Use the INTENSITY UP/DOWN buttons to change the intensity then press STOP/ENTER
button to enter to confirm.
TIME display shows factory default setting “32:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
SMOOTH AGILE TRAINER
COMPUTER OPERATION
Press START button to start the INTENSITY INTERVAL program. Time counts down to 0, Distance and Calories count up.
Dot Matrix display shows the pre-set INTENSITY and MOTION profile. Press INTENSITY UP/DOWN to adjust the resistance
and press MOTION UP/DOWN to adjust the motion.
Motion Interval Program
When the console is in MOTION INTERVAL program set up, MOTION LEVEAL DISPLAY shows “L1”. This indicates the
intensity level for the intervals. Use the INTENSITY UP/DOWN buttons to change the intensity then press STOP/ENTER
button to confirm.
TIME display shows factory default setting “32:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the MOTION INTERVAL program. Time counts down to 0, Distance and Calories count up. Dot
Matrix display shows the pre-set INTENSITY and MOTION profile. Press INTENSITY UP/DOWN to adjust the resistance and
press MOTION UP/DOWN to adjust the motion.
ENDURANCE PROGRAM
When the console is in POWER ON status, press the ENDURANCE program button then press STOP/ENTER to
continue to the set up procedure.
Workout Level set up
TIME display shows “L1”, Press INTENSITY UP/DOWN button to adjust the workout level and press STOP/ENTER to
confirm.
TIME display shows factory default setting “32:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the ENDURANCE program. Time counts down to 0, Distance and Calories count up. Dot Matrix
display shows the pre-set INTENSITY and MOTION profile. Press INTENSITY UP/DOWN to adjust the resistance and press
MOTION UP/DOWN to adjust the motion.
WATTS CONTROL PROGRAM
The function of Watts Control program is to allow the user to set a desired workout load (watts). The user’s
workout load is controlled automatically by increasing or decreasing the resistance as the user changes their
stride cadence (RPM). The intensity will be reduced when user increases RPM and the intensity will be increased
when the user decreases the RPM.
When the console is in POWER ON status, press the WATTS CONTROL program button then press
STOP/ENTER to continue the set up procedure.
WATTS display shows factory default setting “110”. Press INTENSITY UP/DOWN button to adjust the target Watts and press
STOP/ENTER to confirm.
TIME display shows factory default setting “32:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
COMPUTER OPERATION
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press START button to start the WATTS program. Time counts down to 0, Distance and Calories count up. Dot Matrix display
shows the pre-set INTENSITY and MOTION profile. Press INTENSITY UP/DOWN to adjust the resistance and press MOTION
UP/DOWN to adjust the motion
TARGET HEART RATE CONTROL PROGRAM :
The TARGET HEART RATE CONTROL program is designed to keep the user training at their chosen heart rate level to
achieve the proper workout result. A heart rate monitoring device must be used for this program. The equipment provides a
standard contact handgrip on the moving handle bar to sense the user heart beat during the workout. The user must hold the
contact handgrips on the moving handle bar constantly in order to monitor the user heart rate during the workout. A wireless
chest belt transmitter is highly recommended for this program.
IMPORTANT: The console software will calculate the user’s SAFE MAXIMUM HEART RATE based on the formula:
220pbm-AGE. User’s are encouraged to consult with a doctor or personal
Training consultant to more accurately estimate their SAFE MAXIMUM HEART RATE in order to workout safely.
When the console is in POWER ON status, press the HEART RATE CONTROL program button. The 8x16 Dot Matrix displays
“HEART RATE CONTROL” Press STOP/ENTER to continue to the set up procedure.
TIME display shows factory default setting “30:00”. Press INTENSITY UP/DOWN button to adjust the target time and press
STOP/ENTER to confirm.
AGE display shows factory default setting “35”. Press INTENSITY UP/DOWN button to adjust the user age and press
STOP/ENTER to confirm.
PULSE display shows the calculated TARGET HEART RATE based on the user age setting from the above step. The
TARGET HEART RATE = 85% MAXIMUM SAFE HEART RATE. Press INTENSITY UP/DOWN button to adjust the target
heart rate then press the STOP/ENTER bottom to confirm.
WEIGHT display shows factory default setting “68(kgs)/150(Lb). Press INTENSITY UP/DOWN button to adjust the user
weight and press STOP/ENTER to confirm.
Press the START button to start the 3 minute WARM UP. The purpose of warm up program is to bring the user’s heart rate to
65% of the MAXIMUM SAFE HEART RATE. Time counts down from “3.00” to “0:00”. Intensity Level Profile displays “WARM
UP” 3 times. During the WARM UP, if the actual heart rate is less than 65% of the user’s MAXIMUM SAFE HEART RATE, the
intensity level will be increased by 1 level every 15 seconds. If the actual heart rate reaches 65% MAXIMUM SAFE HEART
RATE twice within the warm up, the HEART RATE CONTROL program will start.
If user’s actual hear rate fails to reach 65% of MAXIMUM SAFE HEART RATE during the warm up, the user will be placed
into a 2nd or 3rd (if necessary) 3 minute warm up program. If user’s actual heart rate fails to reach 65% of the MAXIMUM SAFE
HEART RATE after the 3rd 3 warm up program, the INTENSITY LEVEL PROFILE dot matrix will display “FAIL” then return to
POWER ON status in 10 seconds.
Once the user successfully enters the HEART RATE CONTROL program, the computer will actively adjust the resistance
level to keep the users at the TARGET HEART RATE. If the user is consistently below the TARGET HEART RATE, the
INTENSITY LEVEL will increase 1 level. If the user reaches and exceeds the TARGET HEART RATE, the INTENSITY LEVEL
will decrease 1 level. The program will continue until the time runs out. If the user’s heart rate continues to exceed the
TARGET HEART RATE for 3 minutes, or the time counts down to “0:00”, the heart rate control program will stop and start the
1 minute COOL DOWN function. Time counts down from “1:00” and INTENSITY LEVEL AND MOTION LEVEL at level 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
SMOOTH AGILE TRAINER
WARRANTY
LIMITED HOME USE WARRANTY
Warranty Coverage: EVO Fitness and Smooth Fitness, Inc. ("Smooth Fitness") warrants to the original owner that each new product to be free from
defects in workmanship and material, under normal use and conditions.
Period of Coverage: The Warranty on this product runs from the date of original purchase using the following schedule:
Model Name
Frame
Parts & Electronics
Labor
AGILE DMT
Lifetime
5 years
1 year
Labor: Smooth Fitness will reimburse for labor costs for One (1) year. Smooth Fitness reserves the right to either:
Hire and reimburse an independent service technician who will come into the home for the repair,
OR
In the event that there is not an available certified Smooth Fitness service technician, Smooth will send the part directly to the consumer and will pay
$75 US per occurrence for the labor costs of such repair. If multiple repair attempts must be made for one reported problem, Smooth will only
reimburse once per occurrence.
Smooth Fitness reserves the right to inspect damaged parts for misuse. Your Original Receipt is proof of purchase and should be kept with the
product manual. You may be required to show proof of purchase prior to warranty service being initiated.
Remedy Provided by Smooth Fitness: Smooth Fitness will provide a replacement part free of charge if a defect is found during the Warranty period.
Smooth Fitness may at its discretion, choose to provide any of following parts or repair options. In the event that a part is determined in need of
replacement, upon receipt of the part by Smooth Fitness, Smooth Fitness may send out the part by UPS ground or another such carrier directly to
the customer’s home. The customer is responsible for the cost of sending the part to Smooth Fitness.
For the 9.25X Model Only: This warranty covers all parts including frame, electronics and wear parts for a lifetime. If Smooth Fitness in its sole
discretion determines that the treadmill cannot or should not be repaired, it may decide to purchase the unit for the residual value in accordance
with the following: 25% of retail purchase price after 5 years, 15% after 10 years, 5% after 15 years.
Any redemption may be by repair or replacement of the affected parts and/or product at the sole discretion of Smooth Fitness, by personnel
approved by Smooth Fitness.
Parts repaired or replaced pursuant to this Warranty shall be warranted for the unexpired portion of the Warranty applying to the original product.
Any technical advice furnished before or after delivery in regard to the use or application of Smooth Fitness products is furnished without charge
and on the basis that it represents Smooth Fitness' best judgment under the circumstances but that the advice is used at your sole risk.
Procedure for Obtaining Your Remedy Under This Warranty: To obtain service on a Smooth Fitness product, call Smooth Fitness. In the instance
that service is not available in an area, Smooth Fitness, at its discretion, can either 1) find a service technician in your area to perform warranty
service, 2) have a local dealer perform warranty service, or 3) send the warranty parts to you and reimburse as described above. To help the
technician assist you, please have the following information ready:
•
•
•
Model name or number from the cover of the manual;
Serial number located on the frame of the unit; and
The part description and the order number.
Limitations on Warranty: This Warranty will only apply to the original end user. This Warranty does not cover wear and tear (except the 9.25X
treadmill), any problems, damages or failures that are caused by accident, improper assembly, failure to observe cautionary labels on the product,
failure to operate the product correctly, power grid failures or spikes from your local electricity provider, abuse or freight damage. Smooth Fitness
does not warrant against any damage or defects that may result from repair or alterations made to the product by an unauthorized repair facility.
This Warranty shall terminate if you sell or otherwise transfer this product. This Warranty does not apply to any product shipped or handled
outside of the United States or Canada. This Warranty does not apply if the product is used as a rental product or in commercial use. Consequential
and incidental damages are not recoverable under this Warranty. (Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.)
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO ONE (1) YEAR FROM THE EFFECTIVE DATE OF THIS WARRANTY. SMOOTH FITNESS IS NOT
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN PARTS NOR FOR
ANY BREACH OF EXPRESS OR IMPLIED WARRANTIES. SMOOTH FITNESS' SOLE LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE TERMS DESCRIBED IN THIS FORM. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
FORM WS-1 (rev. 08/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
Smooth Fitness
780 Fifth Avenue, Suite 200
King of Prussia, PA 19406
Toll Free Customer Service:
1.888.800.1167
Website:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Printer DX C200P User Manual
Silvercrest Bluetooth Headset SBTF 10 A1 User Manual
Sony Cordless Telephone spp n1025 User Manual
Sony Indoor Furnishings SU SX10 User Manual
Sony Microcassette Recorder WM GX414 User Manual
Sony MP3 Player D EJ915 User Manual
Sony Portable CD Player MZ R4ST User Manual
Sylvania DVD VCR Combo DVC845E User Manual
TAG Games Wrestling DVD Board Game User Manual
Tannoy Portable Speaker Highline 500 User Manual