HOME TECH
6
DVD Player SHDP 5.1 A1
DVD Player
Operating instructions
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
ID-Nr.: SHDP 5.1 A1-01/11-V3
IAN: 64329/64330
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
PAGE
1. Technical Data
2
2
2
2
3
3
4
2. Intended use
3. Package contents
4. Operating components
5. Setting up of the DVD player
6. Safety instructions
7. Remote control
7.1 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
7.2 Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
7.3 Replacing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
8. Connecting the DVD player to a television
4
8.1 Connecting to a television via ScartCable/RGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.2 Connecting to a television via S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.3 Connection to a television via video input (Composite Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.4 Connecting via component signal (YPbPr/YUV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
8.5 Connecting to a television via HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9. Connecting audio components to the DVD player
6
9.1 Requirements for the connection of a HiFi system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9.2 Connecting digital audio components via digital cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9.3 Connecting audio components via an analogue cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9.4 Connecting the headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
10. OSD menu settings
8
10.1 Using the OSD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
10.2 Setup menu GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
10.3 Setup menu AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
10.4 Setup menu DOLBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
10.5 Setup menu VIDEO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
10.6 Setup menu PREFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
11. Initial operation of the DVD player
12
11.1 Switching the DVD player on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
11.2 Inserting the DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
11.3 Inserting memory cards/USB memory sticks with MP3/WMA/ MPEG4/JPEG data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
11.4 Removing memory cards/USB memory sticks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
12. Playing back DVDs, VCDs or S-VCDs
13
12.1 Features during playback of a DVD, VCD or S-VCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
13. Playback of JPEG-Photo CD/WMA/MP3/MPEG4
14. CD Ripping function
15. Cleaning of the DVD player
16. Disposal
18
19
19
19
20
21
22
22
17. Troubleshooting
18. Glossary / Key Word Index
19. Warranty and Service
20. Importer
Read these operating instructions carefully before using the device for the first time and preserve this manual for later reference.
Pass this manual on to whoever might acquire the device at a future date.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD PLAYER
2. Intended use
This documentation is copyright protected.
The SilverCrest SHDP 5.1 A1 DVD player is intended exclusively for stationary
use in enclosed spaces. The device is intended exclusively for private,
non-commercial use.
The device is intended for use as an electronic entertainment device whose
purpose is to display and playback images, music and video files.
No liability/warranty will be accepted for damages that result from improper
use of the device or from unauthorised reconstruction!
Any duplication and/or reproduction, wholly or partially including extracts
as well as the reproducing of illustrations also in modified form is only permit-
ted with written agreement from the manufacturer.
1. Technical Data
This device conforms regarding compliance to the basic requirements and
other relevent provisions of the low-voltage directive 2006/95/EC, the
EMV directive 2004/108/EC as well as the Ecological design directive
2009/125/EC (Ordinance 1275/2008) Supplement II, Number 1).
3. Package contents
-
-
-
-
-
-
-
DVD Player
Infrared remote control
2 Batteries for remote control, type AAA/ (Micro cells)
RGB Scart cable
Audio/Video RCA Cinch cable
HDMI cable
Power supply:
Power consumption:
Power consumption:
Standby:
Protection class:
TV standard:
AC 220 V - 240 V 50 Hz
~
max. 20 Watt
< 1 W
II /
Operating manual
PAL/NTSC
Operating temperature:
Humidity:
Measurements
(W x H x D):
Weight :
Laser class:
+5 +40°C
~
5
90% (no condensation)
4. Operating components
~
43 x 4.3 x 21.6 cm
1.65 kg approx.
1
A. DVD player front panel
Disc compartment
FAST RWD ꢀbutton: Fast search backwards
PLAY/PAUSE ꢁꢂbutton
q
w
e
r
t
y
u
i
o
a
Video Output
Format:
Decoder:
4:3 / 16:9
MPEG 2
12 Bit
STANDBY
button
FAST FWD ꢃbutton: Fast search forward
Memory card slot for SD/MMC/MS and MSPro cards
USB port
Headphones output for 3.5 mm jackplug
Display (with standby LED and IR sensor for the remote control)
D/A converter:
Audio Output
Decoder:
MPEG Dolby Digital (AC-3)
DTS only possible with additional external decoder
24 Bit / 96 kHz
OPEN/CLOSE
button
D/A converter:
B. DVD player rear panel
USB port
Readable
USB memory sticks:
Max. current output:
Power cable
s
d
f
g
h
j
k
l
;
2)
2!
2@
2#
2$
POWER switch
USB1.1.1 and 2.0 up to a capacity of 8GB
100 mA
VIDEO: Composite video output
Y, Pb/Cb, Pr/Cr: Component video outputs
SCART: Scart/RGB output
FL/FR: Output for front, left and right audio channels
SL/SR: Output for rear, left and right audio channels
SW: Output for bass audio channel
CEN: Output for front and centre audio channels
COAXIAL: Coaxial audio output
AUDIO L/R: Left and right audio outputs
HDMI: HDMI output
Memory card slot
Readable memory cards: SD, MS/MSPro, MMC up to 32 GB (if available)
Headphones output
Jackplug:
Maximum
output voltage:
3,5 mm
125 mV
OPTICAL: optical digital audio output
S-VIDEO: S Video output
Playable mediums/formats
Video:
DVD, DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-R DL, DVD+R DL, VCD, S-VCD
CD, CD-R, CD-RW, Audio-DVD, MP3, WMA,
OGG Vorbis
Audio:
Additional formats:
Regional code:
AVI, MPEG 4, Xvid, JPEG (Foto-CD)
or
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Remote control
6. Safety instructions
OPEN/CLOSE : Open/Close the disc tray
Number buttons
q
w
e
r
t
y
u
i
o
a
s
d
f
g
h
j
k
l
;
2)
2!
2@
2#
2$
2%
2^
2&
2*
2(
3)
3!
3@
3#
3$
•
This device is not intended for use by individuals (including children)
with restricted physical, physiological or intellectual abilities or deficiences
in experience and/or knowledge unless they are supervised by a person
responsible for their safety or receive from this person instruction in how
the device is to be used.
DISPLAY: Superimpose disc information
DIMMER: Adjust the display brightness
V-MODE: Set the video output
STOPꢄ: Stop playback
PLAY/PAUSEꢁꢂ: Start/Suspend playback
•
•
•
•
Children should be supervised to ensure that they do not play with the
device.
To avoid unintentionally switching on the device pull the power cord
from the mains supply after use and before cleaning.
Check the device and all parts for visible damages. The safety concept
can work only if the device is in a faultless condition.
The power plug must always be easily accessible, so that the device can
be quickly disconnected from the mains in the event of an emergency.
SKIP FWD
Chapter skip forwards
VOL +/- : Raise/lower the sound level
FAST FWDꢃ: Fast search forward
SUBTITLE: Set the subtitle
ENTER: Confirm input
Control buttons ꢅꢁꢆꢇ
MENU/RIPPING: Access disc menu/ripping function
SLOW: Slow motion function
RETURN: access disc menu/return to playback
ZOOM: Set the image enlargement
PROG: Access the programme function
A-B: Repeat sequence
Risk of electrical shocks!
•
Connect the device only to correctly installed and earthed mains sockets.
Ensure that the rating of the local power supply tallies completely with
the details given on the rating plate of the device.
Battery compartment (on the rear panel)
PBC: PBC function activate/deactivate (VCD, SVCD only)
USB: Change between disc playback and USB/card playback
STEP: Individual frame playback
•
•
•
•
Arrange for defective power plugs and/or cables to be replaced at
once by qualified technicians or our Customer Service Department.
Arrange for customer service to repair or replace connecting cables
and/or devices that are not functioning properly or have been damaged.
Never immerse the device in water. Wipe it only with a slightly damp
cloth.
L/R/ST: Set the audio channel
AUDIO: Set the audio language
TITLE: Access the title menu
FAST RWDꢀ: Fast search backwards
Do not expose the device to rain and never use it in a humid or wet
environment.
SKIP BWD
•
•
Ensure that the power cable never becomes wet during operation.
You must not open the housing or repair the device yourself.
Should you do so, device safety can no longer be assured and the
warranty will become void.
Chapter skip backwards
MUTE : Switch the sound on/off
REPEAT: Set the repeat function
ANGLE: Change the camera perspective
SETUP: Access the OSD menu
•
Protect the device against drip and spray water. Do not place any
water-filled vessels (e.g. flower vases) on the device.
GOTO:Access titles, chapters and time direct select menus
STANDBY : Switch the device to standby mode
Risk of fire!
•
•
Do not use the device in the vicinity of hot surfaces.
Do not locate the device in places exposed to direct sunlight.
If you do, it may overheat and become irreparably damaged.
Do not leave the device unattended when in use.
Never cover the ventilation slots of the device while it is being used.
Do not place any open sources of fire, like candles, on the device.
5. Setting up of the DVD player
1. Carefully remove the DVD player and the supplied accessories from
the packing.
2. Remove the protective foil from the display.
•
•
•
3. Place the DVD player on a flat, even and firm base. Do not subject the
device to any external heat or moisture source. Make sure that the device
has sufficient ventilation on all sides. Do not place any television directly
on top of the DVD player.
Injury hazard!
•
Keep children away from the connecting cable and the device.
Children frequently underestimate the dangers of electrical equipment.
Ensure that the device stands with a safe and secure positioning.
Do not operate the device if it has sustained a fall or is damaged.
Arrange for the device to be checked and/or repaired by qualified
technicians.
•
•
Attention!
Do not plug the DVD player into an electrical outlet at this time.
Wait until you have connected the DVD player to a television set.
•
•
Batteries/ battery cells are potentially fatal if swallowed. Store batteries
out of the reach of children. If a battery is swallowed medical assistance
must be sought immediately.
Also, store the packaging foils well away from children. There is a risk
of suffocation.
In the event that you wish to change the type of video or audio connection
you must first pull the power plug from the power socket! Otherwise the
DVD player and possibly equipment connected to it could become
irreparably damaged through voltage peak strikes!
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Danger! Laser radiation!
This device is fitted with a „Class 1 Laser“.
• Never open the device.
7. Remote control
7.1 Inserting the batteries
• Never attempt to repair the device.
1. Open the battery compartment on the rear of the remote control.
2. Place the two supplied batteries type AAA (micro cells) into the battery
compartment. Make sure that the batteries are inserted in accordance
with the correct polarity.
• There is invisible laser radiation inside the device.
Do not expose yourself to the laser beam.
Note:
3. Replace the battery compartment cover.
Some aggressive furniture finishes can have a destructive influence on the
device's rubber feet. If necessary, place the device on a nonslip pad.
7.2 Using the remote control
In order to guarantee faultless operation when using the remote control…
Thunderstorms!
•
•
Always point the remote control, during use, directely at the DVD player
Make sure that there are no obstructions between the remote control
and the DVD player that will hinder reception.
Equipment connected to a power supply can be damaged during a
thunderstorm. You should therefore always pull the power plug from the
power socket when there is a storm.
•
When using the remote control place yourself not more than 5 metres
from the DVD player
Notice regarding electrical power surges
(EFT / electrical fast transient) and electrostatic discharges:
otherwise interferences can occur during operation of the DVD player functions
with the remote control.
In the case of malfunction due to an electrical fast transient (power surge)
and/or electrostatic discharge, the device must be returned to default
settings in order to re-establish normal operation. The power supply may
have to be disconnected and then reconnected. The batteries (if present)
must be removed and then reinserted.
7.3 Replacing the batteries
If the operation of the DVD player via the remote control does not function
properly or does not function at all the batteries must be replaced
•
Always renew all batteries in order to return the remote control to its full
performance ability.
Notice regarding disconnection from mains-power
The POWER switch does not completely disconnect the device from
the power network. Additionally, the device consumes power when in
standby-mode. To completely disconnect the device from mains-power,
the power plug MUST be removed from the wall socket.
8. Connecting the DVD player to a television
After setting up the DVD player, you can now connect it to a television.
The DVD player can be connected to televisions which operate with the PAL
and NTSC standards.
If you want to use the DVD player on a television with the NTSC standard
you must change the video setting in the DVD players "OSD menu". There
PAL is set as the television standard at the factory. Depending on the televisions
equipment there are different methods of connecting the DVD player to it,
these are explained as follows.
Information regarding the handling of batteries
The remote control is operated by batteries.
For the safe handling of batteries please observe the following safety
information:
Danger exists from uses other than those intended!
Do not throw the batteries into a fire.
Do not short circuit the batteries.
Do not attempt to recharge the batteries.
Regularly check the condition of the battery. Leaking battery acid can
cause permanent damage to the device. When handling a damaged or
leaking battery special care should be taken. Danger from acid burns!
Wear protective gloves.
•
•
•
•
•
•
Clean the battery compartment and the battery contacts with a dry cloth.
Store batteries out of reach of children. When swallowed seek immediate
medical attention.
•
•
Remove the batteries from the device if you do not intend to use the device
for an extended period of time.
Never open batteries, never solder or weld batteries.
The risk of explosions and injuries exists!
Attention!
No liability/warranty will be considered for damage to the DVD player
caused by the effects of moisture, water penetration or overheating!
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8.1 Connecting to a television via ScartCable/RGB
•
•
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/
S-VIDEO .
Note:
Connecting the DVD player to a television with a Scart cable via the RGB input
offers a high quality connection. Select this connection variation in the case of
televisions equipped with an RGB input. If you are not sure if the television is
equipped with an RGB input then you can check this by consulting the television's
instruction manual.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
8.3 Connection to a television via video input
(Composite Video)
For this connection variant the television must be equipped with Audio/Video
cinch sockets (Composite Video).
In order to connect the DVD player to a television via Composite Video you
will need
•
an audio/video RCA cinch cable (supplied)
•
•
•
Connect the jack inscribed with SCART to a television Scart socket by
using the supplied Scart cable.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select under the VIDEO/VIDEO OUTPUT/RGB or
S-VIDEO menus.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
•
•
Connect the yellow marked video socket with the yellow VIDEO socket on
the television.
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player to the corresponding audio inputs on the television. Make sure
that the colour markings yellow, red and white correspond.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/
S-VIDEO.
8.2 Connecting to a television via S-Video
Note:
•
•
For this type of connection the television must have available an S-Video input
and two audio "IN" cinch sockets. If you are not sure if the television is equipped
with S-Video and/or cinch sockets you can check this by consulting the television's
instruction manual.
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
For this connection variant you will need:
•
•
an audio cinch cable (not supplied)
an S-video cable (not supplied) These can be obtained from your dealer.
To connect the DVD player to a television via S-Video:
8.4 Connecting via component signal (YPbPr/YUV)
This connection variant is only possible with very high grade televisions,
LCD/Plasma screens or Video projectors.
Check with the instruction manual of the corresponding playback device to
see if this connections variant is available. It is possible that additional playback
device settings may have to be implemented.
The so called "Component signal" is put out via the YPbPr socket of the DVD
player. Component signals are available in the form of the so called "YUV"
signal (Half image) as well as in the form of the so called "YPbPr" signal
(Full image/Progressive scan).
On this topic, please refer to Section 18. "Glossary / KeyWord Index".
The cable connections are the same in both cases; YPbPr-signal for Progressive
Scan however can only be used if the television (or Video projector), to which
you want to connect the DVD player, is capable of Progressive Scan. If you
are not sure whether the television (or Video projector), to which you want to
connect the DVD player is capable of Progressive Scan and has cinch sockets
available then you can check this by consulting the television's (or Video
projectors's) instruction manual.
•
•
Connect the jack inscribed with S-VIDEO to a television S-Video socket
using an S-Video cable.
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player via an audio cinch cable to the corresponding audio inputs on
the television. Make sure that the red and white colour markings
correspond.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
For both variations – "YPbPr" and "YUV"– you will need
•
•
an audio cinch cable (not supplied)
an YUV cable (not supplied) These can be obtained from your dealer.
9. Connecting audio components to the
DVD player
On the rear panel of the DVD player you will find the connection sockets
Y, Pb/Cb and Pr/Cr.
Besides sound playback of DVDs, VCDs/S-VCDs and audio and MP3-CDs
via the speaker of the television, to which the DVD player is connected,
sound can also be played back via external audio components such as
a HiFi system, Dolby digital/DTS receiver or a surround sound system.
Connecting the DVD player via component signal:
9.1 Requirements for the connection of a HiFi system
In order to enjoy a full sound experience when playing DVDs with the DVD
player you can connect a HiFi system to the player. Before connecting check
with the HiFi system's instruction manual to verify...
•
•
if the HiFi system is suitable for connection to a DVD player.
if the HiFi system is equipped with cinch sockets; if yes, you can connect
the HiFi system to the DVD player via cinch cables.
Connecting a HiFi system:
•
•
Connect the sockets Y (green), Pb/Cb (blue) and Pr/Cr (red) with the cor-
responding sockets on the television.
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player to the corresponding audio inputs on the television with an audio
cinch cable.
Make sure that the red and white colour markings correspond.
•
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/VIDEO OUTPUT/YUV.
•
The menu option VIDEO OUTPUT is only selectable when the HDMI output
is deactivated. On this subject see also chapter 10 "Settings in the OSD
menu".
•
•
Connect the audio output sockets AUDIO L/R on the rear panel of the DVD
player to the corresponding audio inputs on the HiFi system with an audio
cinch cable. Make sure that the red and white colour markings correspond.
Check with the instruction manual which settings on the HiFi system may
be necessary in order to reproduce sound via the HiFi system during the
playback of a DVD, VCD/S-VCD, audio or MP3-CD from the DVD player.
8.5 Connecting to a television via HDMI
This connection variant is only possible with very high grade televisions,
LCD/Plasma screens or Video projectors
Check with the instruction manual of the corresponding playback device to
see if this connections variant is available. It is possible that additional play-
back device settings may have to be implemented. For this type of connection
you will need the HDMI cable (supplied);
Note:
For an optimal sound experience place your HiFi system's loud speakers to
the left and to the right of the television, on which you connected the DVD
player.
Connecting the DVD player via HDMI:
If you connected the DVD player to the television via a Scart cable the audio
signal will be transmitted via the cinch cable to your HiFi system as well as
via the Scart cable to the television. In this case, set the volume of the television
to the lowest value.
9.2 Connecting digital audio components via digital cables
In order to enjoy sound playback throughout the room from correspondingly
equipped DVDs (recognizable by the Dolby Digital or DTS logos), you can
connect the DVD player to a digital audio component, for example, a Dolby
Digital or DTS receiver or a suitable surround sound system.
The cables necessary for the following described connection variations can
be obtained from your dealer.
•
•
•
Connect the jack inscribed with HDMI using a HDMI cable to the
corresponding socket on the television.
For playback select the matching channel on your television Check with
the television's instruction manual on how you can set the AV channel.
In the OSD menu select the menu option VIDEO/HDMI Setup/ON.
On this subject see also chapter 10 "Settings in the OSD menu".
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Firstly check with the digital component’s instruction manual to see if it allows
for connection to the DVD player...
9.3 Connecting audio components via an analogue cable
If a digital input is not available on the audio component you can connect
the DVD player to it via conventional analogue cinch cables.
•
•
via a coaxial cable
or via an optical cable.
Connection via coaxial cable
To connect the DVD player to a digital audio component with a digital coaxial
cable:
•
Connect the COAXIAL inscribed plug to the corresponding socket on the
digital audio component.
To connect the DVD player with analogue cables:
•
Plug a cinch cable into each of the sockets FL (front left channel),
FR (front right channel), SL (rear left channel), SR (rear right channel),
CEN (front centre channel) and SW (Bass) on the rear panel of the DVD player.
Insert the cinch cables into the corresponding analogue inputs of the
audio component.
•
Connecting via optical cable
To connect the DVD player to a digital audio component with an optical cable:
•
Remove the protective plug from the OPTICAL inscribed socket on the rear
panel of the DVD player and insert the optical cable plug.
Insert the plug at the other end of the optical cable in the corresponding
socket of the digital audio component.
9.4 Connecting the headphones
The headphones output is located on the front panel of the DVD player.
•
•
Plug the 3.5 mm headphones jackplug into the headphones output.
The audio output also continues to come out via the television set.
Note:
Attention!
The optical cable is a glass fibre cable and must not be bent during installation.
Otherwise the glass fibre contained in the cable could break and the cable
would become unusable.
Listening to music with headphones for long periods and at high
volume levels can lead to hearing damage!
Note:
Make sure that no dirt can enter into the optical cable socket. This could cause
signal interference. Always insert the protective plug into the socket if no optical
cable is connected.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
10. OSD menu settings
10.1 Using the OSD Menu
•
To access the DVD players OSD menu press the SETUP button on the remote
control. The OSD Menu with its menu options will appear on the television
screen:
All of the DVD player's settings can be made with the remote control via
the so called "On Screen Display" menu ("OSD menu" for short). The OSD
Menu will be superimposed on the television screen.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
Note:
TV DISPLAY
PS
In these instructions the English OSD menu is described. At any time you can
set the menu to your country's language as described in "GENERAL > OSD
LANGUAGE".
ANGLE MARK
ON
ENG
OFF
ON
OFF
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
LAST MEMORY
TV DISPLAY
PS
ANGLE MARK
ON
ENG
OFF
ON
OFF
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
The following menu options can be selected:
GENERAL, AUDIO, DOLBY, VIDEO and PREFERENCE.
• With the control buttonsꢅꢁꢆꢇand the ENTER button you can carry
out all the settings in the menu.
• With the control buttons ꢅꢁyou can select a menu by moving the yellow
marking onto the corresponding menu symbol.
LAST MEMORY
Before you use the DVD player for the first time for playback of DVDs,
VCDs/S-VCDs or audio/MP3-CDs you must implement a few settings via the
OSD Menu. These settings are dependent amongst others on...
• With the control buttons ꢆꢇyou select an input in a menu by moving
the green bar over an input.
• With the control buttonꢁyou change an input in the sub menu and with
the control button ꢅyou move back to the previous menu level.
• To confirm a selection press the ENTER button.
•
•
the language, in which you want the OSD menu to be displayed
which TV standard corresponds to the television, to which you want to
connect the DVD player
All navigation possibilities in a current menu are displayed at the lower
•
Which image format your television can display
edge of the menu.
• To exit the OSD menu press the SETUP button again.
Administering settings via the OSD menu
•
First insert the connector plug of the DVD player's power cord into
a power socket.
10.2 Setup menu GENERAL
In this menu you can, for example, set the image presentation or the language
of the OSD menu.
•
To switch the DVD player on activate the POWER switch on the rear panel
of the DVD player. If the DVD player is already switched on but is in
standby mode, press the button STANDBY on the remote control to
switch the DVD player on. The standby mode is identified by the LED in
the display on the front panel of the device.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
TV DISPLAY
PS
ANGLE MARK
ON
ENG
OFF
ON
OFF
The device will check to see if a disc is inserted. The SilverCrest logo appears
on the television screen:
OSD LANGUAGE
CLOSED CAPTIONS
SCREEN SAVER
LAST MEMORY
TV DISPLAY
-4:3/PANSCAN Select this setting to display broadcasts in the usual 4:3
format on a 4:3 television set. Broadcasts in the 16:9 format
will be displayed in full screen without the distracting bars
although the side edges of the image will be trimmed.
-4:3/LETTERBOX Display of a film in 16:9 format on a traditional 4:3 format
television. The image is displayed with black bars on the
lower and upper edges of the screen.
If no disc is inserted the notification NO DISC appears on the television
screen and in the display.
-16:9
This setting is recommended when using a wide screen
television in 16:9 format. An image in 4:3 format will be
adapted horizontally to the image width.
•
Firstly please familiarize yourself with the OSD Menu's operation by
means of the following brief introduction.
-Wide Squeeze An image in 4:3 format will be presented with black bars
on the right and left edges.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ANGLE MARK
-ON
-3D SURROUND Select this setting to produce a virtual surround effect from
If scenes are recorded on a DVD in different perspectives
this will automatically be signified by a camera symbol
displayed on the television screen. Press the ANGLE button
on the remote control to display the various perspectives.
Deactivate function. No symbol appears on the television
screen.
a stereo or multi channel sound.
-5.1 CH
Select this setting to activate the analogue 5.1 outputs.
FRONT SPEAKER, CENTER SPEAKER, REAR SPEAKER and SUBWOOFER
In these menu inputs you can activate/deactivate the individual speaker types
and set the size.
-OFF
-LARGE
Select this setting if the diameter of the speaker membrane
is greater than 12 cm.
OSD LANGUAGE
Here you set the language, in which the OSD Menu will be shown on the
display.
-SMALL
-OFF
Select this setting for smaller speakers.
Deactivate sound output for these types of speakers
CLOSED CAPTIONS
Note:
-ON
Select this setting if by every playback of a DVD the subtitle
(if present) is to be automatically displayed on the television
screen.
The menu input FRONT SPEAKER can not be deactivated since the sound
output for the front speakers always remains switched on.
-OFF
Select this setting to manually activate the subtitle.
The subtitles can also be set, during playback, with the
SUBTITLE button.
DIALOG
In this menu input you can set the dialogue volume (0-20).
D.R.C. (Dynamic Range Control)
This function sets the level of the dynamic range for motion picture soundtracks
which are optimised for Dolby Digital. The function is particularly useful when
listening to surround sound with a low volume level.
SCREEN SAVER
-ON
Screen saver activated. The screen saver will now switch
on when the playback is stopped and no input is made for
approx. 4 minutes.
-ON
Function activated
-OFF
Function deactivated.
-OFF
Deactivate function.
-AUTO
Function (if available) is automatically activated
LAST MEMORY
-ON
Select this setting to playback a disc from the previously
halted position after removal and re-insertion.
DIGITAL AUDIO
DIGITAL OUTPUT
-OFF
Deactivate function. The disc playback starts back at the
begining after removing and then reinserting.
In this menu input you can set the SPDIF output signal.
-SPDIF / OFF
No digital audio signal is being put out at the sockets
COAXIAL or OPTICAL.
Note:
-SPDIF / RAW
-SPDIF /PCM
The crude data of the Dolby Digital sound is put out.
Select the setting PCM (Pulse Code Modulation) when there
is a connection to a digital amplifier/receiver. Your DVD
player transmits, through the PCM signal, the same audio
formats that are rendered on the disc. In addition an audio
signal will be put out via the sockets FL and FR.
If the DVD player is turned off with the POWER switch the saved position will not
be preserved.
10.3 Setup menu AUDIO
In this OSD menu you can, for example, carry out settings for the analogue
as well as the digital audio outputs.
LPCM OUTPUT Select this input to set the sampling frequency for the
processing of the crude data.
Default setting.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
-48K:
-96K:
Only for DVDs with the corresponding sampling frequency.
ANALOG AUDIO
DIGITAL AUDIO
CHANNEL DELAY
EQUALIZER
Note:
The LPCM OUTPUT function is only available if you have set the SPDIF audio
output signal to PCM.
3D PROCESSING
CHANNEL DELAY
Select this menu input to set the channel delay of the individual speakers.
With optimal settings the sound reaches your ears simultaneously from all
directions.
ANALOG AUDIO
DOWNMIX
If you use the analogue 5.1 output in this menu you can carry out the
appropriate settings.
With the control button ꢁgo to the graphics field beside the input.
With the control buttons ꢆor ꢇselect the speaker.
With the control buttons ꢁꢅyou increase/decrease the value in increments
of 10 cm. The maximum setable deviation for the CENTER speaker is 170 cm.
The maximum setable deviation for the SUBWOOFER and the rear speakers
is 510 cm.
-LT/RT
Only the left and right channels at the sockets FL and FR
will put out signals.
-STEREO
A stereo sound will be put out. Select this setting if you are
not using the analogue 5.1 outputs. The menu options
CENTER SPEAKER and REAR SPEAKER are then not requi-
red and therefore inactive.
Confirm your entry by pressing the ENTER button.
Note:
The channel delay is determined by the front speakers therefore these are not
selectable.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUALIZER
-SOUND MODE Select this menu input if, when playing back sound, you
want to use one of the preset equalizer levels ROCK, POP,
LIVE, DANCE, TECHNO, CLASSIC or SOFT. To deactivate
this function select the input OFF.
10.4 Setup menu DOLBY
In this OSD menu you can undertake settings for the 5.1 outputs.
GENERAL
AUDIO
DOLBY
VIDEO PREFERENCE
-BASS BOOST
Select the setting ON if you want to boost the playback of
the base tone. To deactivate this function select the input OFF.
Select the setting ON to use the super base sound effect.
In addition playback of the base tone will be boosted.
To deactivate this function select the input OFF.
DUAL MONO
DYNAMIC
-SUPER BASS
-TREBLE BOOST Select the setting ON if you want to boost playback of the
treble sounds. To deactivate this function select the input OFF.
3D PROCESSING
Select this menu input if you want to activate/deactivate the Pro Logic II process.
DUAL MONO
DYNAMIC
Select this menu input to set the Dolby-Digital output to either
STEREO, L-MONO, R-MONO or MIX-MONO.
Select this menu input to enable an optimal sound playback
with reduced volume. In the setting FULL the louder passages
will be surpressed and the softer passages will be played
back louder.
Note:
The menu option PRO LOGIC II can only be selected if the analogue
5.1 outputs are activated.
-PRO LOGIC II Select the setting ON if the process is to be activated all
the time.
Note:
Select the setting AUTO if the process is only to be activated
when Dolby Pro Logic II encoded content is located on the
playback medium.
To deactivate this function select the input OFF.
In this menu you can set the Pro Logic II
process mode.
MUSIC: Sound is played back through the speakers
without delay.
MOVIE: Sound is played back with a delay of 10 ms
through the rear speakers.
This function is only possible when using a Dolby Digital coded 2 channel DVD.
10.5 Setup menu VIDEO
In this menu you can, for example, carry out settings for the video output,
resolution or colour.
-MODE
GENERAL
AUDIO
DOLBY
RGB
VIDEO PREFERENCE
VIDEO OUTPUT
RESOLUTION
COLOR SETTING
HDMI SETUP
PRO
LOGIC: Earlier version of the DOLBY PRO LOGIC processes.
AUTO: Automatic setting of the processes (depending on
the contents of the playback medium).
Xvid SUBTITLE
ENG
Note:
The menu inputs PANORAMA, DIMENSION and CENTER WIDTH serve to
fine tune the sound and are only available if you have set the process mode
MUSIC.
VIDEO OUTPUT
-S-VIDEO
The video signal will be put out via the S-video output and
the composite video output.
-PANORAMA
-DIMENSION
Select the setting ON to activate this sound enhancement.
To deactivate this function select the input OFF.
Select one of the settings SIZE -3 to SIZE 3 to activate this
sound enhancement.
-YUV
-RGB
The video signal will be put out in YUV colour format via
the component video outputs Y, U/Pb, V/Pr.
The video signal will be put out in RGB colour format via
the SCART connection.
-CENTER WIDTH Select one of the settings LEVEL 0-7 to receive a corresponding
sound enhancement.
Note:
This setting is only active if the HDMI setup is deactivated.
REVERB MODE Select this menu input if you want to use, for sound playback,
one of the preset reverbs CONCERT, LIVING ROOM, HALL,
BATHROOM, CAVE, ARENA, or CHURCH. To deactivate
this function select the input OFF.
The composite video output on the DVD player is always activated. If the selected
setting deviates from the actual connection variation (apart from composite video)
it is possible that no image or a poor image will be displayed on the television
screen. In this event press, when playback is stopped, several times the V-MODE
button on the remote control until the image is displayed properly.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
RESOLUTION
In this menu input you can set the different resolutions
(480i/480p/576i/576p/720p/1080i/1080p for the
HDMI output/component video output.
AUDIO
In this menu input you can set the language that is to be
the standard used when playing back films.
)
SUBTITLE
DISC MENU
PARENTAL
Note:
In this menu input you can set the subtitle language that is
to be the standard used when playing back films.
In this menu input you can set the disc menu language that
is to be the standard used when playing back films.
In this menu input you can determine the age restrictions.
Note:
With a deactivated HDMI output only the 576p resolution will be displayed.
Be aware that for the TV standard PAL a setting with 50 Hz and for the TV
standard NTSC a setting with 60 Hz must be selected.
COLOR SETTING
Only a few DVDs have a technical age restriction available. If there is no technical
age restriction on the DVD your DVD players child lock feature can not
be activated. The child lock can only function if it is activated on the DVD player
and a corresponding code is available on the inserted DVD.
If you insert a DVD which, according to the child lock, may not be played back
a window appears on the screen, in which you must enter your password and
confirm with ENTER. Some DVDs and CDs are encoded with encryption signals.
In this way DVDs can be divided into eight different approval classes.
Select one of the following approval classes to protect the playback of
this media class with a password request:
In this menu input you can implement the settings, for example, for the brightness,
contrast or hue.
-SHARPNESS
Select this menu input to set one of the predefined sharpness
values (HIGH, MEDIUM or LOW).
With the help of the control buttonsꢅꢁset the brightness
from -20 to +20. Subsequently press the ENTER button to
continue.
With the help of the control buttonsꢅꢁset the contrast
from -16 to +16. Subsequently press the ENTER button to
continue.
Select this menu to set one of the predefined gamma values
(HIGH, MEDIUM, LOW or NONE).
-BRIGHTNESS
-CONTRAST
1 KID SAFE:
2 G:
3 PG:
also suitable for young children
for all age groups
adult supervision recommended;
adult supervision strongly recommended; some scenes are
not suitable for children under 12
-GAMMA
-HUE
With the help of the control buttonsꢅꢁset the hue from -
9 to +9. Subsequently press the ENTER button to continue.
4 PG 13:
-SATURATION With the help of the control buttonsꢅꢁset the saturation
level from -9 to +9. Subsequently press the ENTER button to
continue.
5 PGR:
6 R:
7 NC 17:
8 ADULT:
for children under 16; adult supervision recommended
for children under 16; adult supervision strongly recommended
not for teenagers under 18 years of age
for adults only
-LUMA DELAY
Select this menu input to set one of the predefined gamma
values (0 T or 1 T).
HDMI Setup
-ON
-OFF
Example
Select this menu input to activate the HDMI output.
Select this menu input to deactivate the HDMI output.
In this menu input you can set the Xvid subtitle language
that is to be the standard used when playing back films.
If a DVD was encoded with, for example, approval class 7 or 8 and you have
an approval class setting between 1 and 6 then a message follows and the
password must be entered. Also only parts of the DVD, that is to say certain
film scenes, may be encoded with an approval class or various approval classes.
Xvid SUBTITLE
10.6 Setup menu PREFERENCE
In this menu you can, for example, carry out the settings for the video output,
activate/deactivate the child lock or change the password.
•
To activate the approval class you must select, in the PARENTAL menu,
the desired approval class and enter the password (136900).
Confirm your entry by pressing the ENTER button.
Note:
PASSWORD
In this menu input you can change the factory default
password (136900) and assign your own password.
Only the numbers 0-9 can be used.
The menu option PREFERENCE is only selectable when playback is
completely finished.
Note:
GENERAL
AUDIO
DOLBY
PAL
VIDEO PREFERENCE
In the event that you forget your new password you can use the factory preset
password (136900).
TV TYPE
AUDIO
ENG
ENG
ENG
DEFAULT
In this menu input you can restore the DVD players factory
defaults.
SUBTITLE
DISC MENU
PARENTAL
PASSWORD
DEFAULT
TV TYPE
-PAL
PAL television standard
-NTSC
NTSC television standard.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Initial operation of the DVD player
11.3 Inserting memory cards/USB memory sticks with
MP3/WMA/ MPEG4/JPEG data.
After you have …
•
•
placed the DVD player in a suitable location
connected the DVD player to a television by one of the designated
connection options
connected the DVD player, if desired, to a HiFi or Surround system
(analogue/digital) for example a Dolby Digital or DTS receiver
made the remote control ready for operation by inserting the batteries
and know how to activate and operate the OSD menu with the remote
control
Note:
The DVD Player always starts in DVD mode. To read memory cards/USB memory
sticks press repeatedly the USB button on the remote control until the desired
medium is shown on the screen. The DVD player recognizes the data formats
JPEG, MP3, WMA and MPEG4.
•
•
•
In order to insert memory cards of the types SD, MS/MSPro and MMC into
the DVD player:
… the DVD player is ready for operation.
•
•
Switch on your television.
Make sure that the DVD player is ready for operation.
11.1 Switching the DVD player on/off
If the television, the DVD player and possibly other connected devices (i.e. an
audio component) are ready for operation and are switched on and the DVD
player is connected correctly to the television you will now see the Silvercrest
logo on the TV screen
• Insert the mains power cable into a properly installed mains power socket.
• Place the POWER switch on the rear panel of the device to the ON position.
The DVD player is now in standby mode.
• With the STANDBY
button on the remote control or the STANDBY
button
If no disc is inserted into the DVD player's disc tray: The message NO DISC is
displayed on the television screen.
you switch the DVD player on and/or back to the standby
on the device
mode.
•
Slide the memory card into the memory card slot.
Then proceed with the following steps depending on the type of memory
card that you want the device to read.
• To switch the DVD player off place the POWER switch on the rear panel of
the device to the OFF position.
Note:
Warning!
The device has no display indicators when it is switched off or in the standby
mode. In the standby mode only the standby LED will light up in the display.
Always make sure that you insert memory cards into the memory card slot as
described hereafter! Under no circumstances bend or buckle the memory
card when inserting into the memory card slot! Slide the memory card up to
the stop in the memory card slot, with a light pressure.
11.2 Inserting the DVD
To play a disc with the DVD player:
•
•
Switch on your television.
Make sure that the DVD player is ready for operation.
Allow the memory card to slide in without force:
•
Check to make sure that the memory card is one that the DVD player is
capable of reading.
If the television, the DVD player and possibly other connected devices (i.e. an
audio component) are ready for operation and are switched on and the DVD
player is connected correctly to the television you will now see the Silvercrest
logo on the TV screen
If no disc is inserted into the DVD player's disc tray:
The message NO DISC is displayed on the television screen.
Do not attempt to insert memory cards of another type in the memory
card slot!
•
•
Make sure that you have inserted the memory card into the memory
card slot in the correct manner.
Under no circumstances attempt to force the memory card into the memory
card slot!
•
Open the disc tray by pressing the button
OPEN/CLOSE on the remote con-
trol or on the front panel of the DVD player. OPEN is displayed on the
television screen.
Otherwise the DVD player, memory card and the data on the memory card
could be damaged!
•
•
Insert the disc in the disc tray with the inscribed/labled side up.
For two-sided discs: The side you would like to play must face down.
Supported memory card types and capacities
Memory cards of the types SD, MS/MSPro, MMC up to 32 GB (if available)
can be played back..
After you have inserted the disc press the button
OPEN/CLOSE on the re-
mote control or on the front panel of the DVD player again to close the
disc tray.
•
The contents of the disc will now be loaded; this may take a few seconds.
In the meantime LOADING is displayed on the television screen.
Note:
Your DVD player can only read storage mediums with several data formats if
each folder contains only one data format.
MultiMediaCard- /SecureDigital memory cards (MMC/SD)
Insert the MMC/SD memory cards with the contacts forward and slide them
straight into the memory card slot.
With this the side of the memory card, on which the contacts are located
must face downwards with the chamfered corner facing to the right.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
MemoryStick/memory cards (MS/MSPro)
Slide the MS memory card into the memory card slot, level and with the
contacts facing forward.
12. Playing back DVDs, VCDs or S-VCDs
With this the side of the memory card, on which the contacts are located
must face downwards with the chamfered corner facing to the left.
To play back a DVD/VCD/S-VCD with the DVD player...
•
•
Switch on your television.
Make sure that the DVD player is ready for operation.
If the television, the DVD player and possibly other connected devices (i.e. an
audio component) are ready for operation and are switched on and the DVD
player is connected correctly to the television you will now see the "Silvercrest"
logo on the TV screen
USB memory sticks (USB)
The DVD player supports USB memory sticks 1.1 and 2.0 up to a capacity
of 8 GB.
USB memory sticks must be inserted into the USB port.
• Open the disc tray on the front panel of the DVD player by pressing the
OPEN/CLOSE button.
OPEN now appears in the display on the front panel of the DVD player and
on the television screen.
• Insert a DVD/VCD/S-VCD disc in the disc tray with the inscribed/labled
side up.
• Press the OPEN/CLOSE button again to close the disc tray.
CLOSE will appear in the display on the front panel of the DVD player and
on the television screen while the disc tray is closing.
• The contents of the inserted DVD/VCD/S-VCD will now be loaded; this
may take a few seconds. In the meantime LOADING blinks in the display
on the front panel of the DVD player and on the television screen.
• Playback of the inserted DVD/VCD/S-VCD starts automatically.
•
Press the USB button on the remote control. If several memory mediums
(USB and memory card) are inserted press, repeatedly, the USB button
until the contents of the USB memory stick is displayed. This procedure
also applies to particular memory cards.
11.4 Removing memory cards/USB memory sticks
Memory cards/USB Memory sticks should then only be removed after the
memory card slot is deactivated. Thus avoiding the possibility of damage or
data loss.
Note:
DVDs, VCDs and S-VCDs that you want to playback with the DVD player
may possibly have a country code which is printed on the DVD's jacket.
•
Press the USB button on the remote control repeatedly until you have retur-
ned to the DVD mode. For this a disc must be inserted into the DVD player.
You can now remove the memory card/USB memory stick from the memory
card slot/USB port.
The DVD player can only playback DVDs/VCDs/S-VCDs with the country code
If no country code is printed on the cover of a DVD/VCD/S-VCD...
.
•
• but instead the symbol
, then the DVD/VCD/S-VCD can be
played back with the DVD player
• then the DVD/VCD/S-VCD can possibly not be played back with the
DVD player. You can check this by attempting to play back the DVD.
Depending on the inserted DVD/VCD/S-VCD it is possible that the contents
of the DVD/VCD/S-VCD will not playback immediately, rather first a selection
menu appears on the television screen.
In this event select the menu option, which will start the playback of the film,
with the control buttons ꢅꢁꢆꢇon the remote control.
• To start playback of the film press the ENTER button on the remote control
or press the PLAY/PAUSEꢁꢂbutton.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
In the display on the front panel of the DVD player, the following notices
Access the DVD menu (MENU)
appear:
With DVDs:
Note:
•
•
•
"DVD"
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
the number of the currently playing chapter
the played back so far time of the currently playing DVD in minutes and
seconds
is displayed on the television
With many films on DVDs there is a main menu on the disc which, apart from
the option of playing back the main film, allows you to select from the following
contents:
With VCDs/S-VCDs:
•
•
•
"VCD" or "S-VCD"
the number of the currently playing title
the played back so far time of the currently playing VCD/S-VCD in
minutes and seconds
•
•
•
the subtitle and film dialogue languages
direct chapter selection
to playback the films bonus material (Background information,
"Making of" etc.)
12.1 Features during playback of a DVD, VCD or S-VCD
During the playback of a DVD/VCD/S-VCD you can use the following DVD
player features...
If such a menu is present on the DVD inserted in the DVD player you can access
it during playback by pressing the MENU button on the remote control.
You can select particular menu options by pressing the control buttons
ꢅꢁꢆꢇon the remote control.
Pause playback
To pause the playback of the inserted DVD/VCD/S-VCD...
To confirm the selected menu option press the PLAY/PAUSEꢁꢂbutton or the
ENTER button on the remote control.
•
During playback press the PLAY/PAUSEꢁꢂbutton
To return to playback press the MENU button on the remote control again.
ꢂwill now appear in the display on the front panel of the DVD player and
on the television screen.
Note:
On the television screen you will see a freeze frame of the scene that has just
been halted.
If you cancel playback by pressing the STOPꢄbutton twice (Playback stop without
resume function) access to the disc's main menu is no longer possible.
•
To contnue playback of the film press the PLAY/PAUSEꢁꢂbutton.
Playback Control (PBC) with VCDs/S-VCDs
Stop playback (STOPꢄ)
To stop playback of the film on the inserted DVD/VCD/S-VCD press the
STOPꢄbutton.
Many VCDs/S-VCDs have Playback Control (in short "PBC"). Playback Control
indicates a main menu that allows operation of several functions of the
VCD/S-VCD.
With resume function
If PCB is available on a VCD/S-VCD inserted in the DVD player you must first
activate it in order to be able to superimpose the menu.
• During playback or when playback is stopped press the PBC button.
The message PBC: OFF appears in the display.
• Press the PBC button again. The message PBC: ON appears in the display. PBC
is now switched on and the disc's main menu can be accessed with the
buttons MENU, TITLE or RETURN.
If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing
the STOPꢄbutton once the DVD player automatically saves the position
where playback was interrupted. This function is called the "resume function".
PRESS PLAY KEY TO CONTINUE appears on the television screen. As
soon as you press the PLAY/PAUSEꢁꢂbutton again playback will continue
from the saved position.
Without resume function
If you have cancelled playback of the inserted DVD/VCD/S-VCD by pressing
the STOPꢄbutton once and you press the STOPꢄbutton a second time the
saved position, at which you interrupted the playback, will be cleared.
When you press the PLAY/PAUSEꢁꢂbutton again playback of the inserted
DVD/VCD/S-VCD starts from the beginning.
Note:
If you switch on PBC during playback then it is possible that playback will
stop and start again from the beginning and/or with the main menu.
Skip to start of chapter (Skip)
Note:
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
With the buttons SKIP FWD
and SKIP BWD
you can, during playback,
within the film on the inserted DVD/VCD/S-VCD …
•
•
skip forward to the beginning of the next chapter or
skip backward to the preceeding chapter
The respectively selected chapter will playback immediately without having
to press the PLAY/PAUSEꢁꢂbutton. The number of the respectively selected
chapter will be displayed on the front panel of the DVD player to the left of
the played back so far time.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Input of the chapter / title number via the number buttons
Audio CD
• During playback press repeatedly the GOTO button on the remote control.
The following notices appear, one after the other, in which you can enter
a time position with the number buttons:
Note:
This function may not be available on all DVDs! If you attempt to execute
DISC GOTO:
Enter here a time position on the disc from where playback
should start.
a function that is not available, the symbol
screen.
is displayed on the television
TRACK GOTO: Enter here a time position for the currently playing back
title from where playback should start.
SELECT TRACK: Enter here a title number from where playback should start.
Instead of using the skip function you can enter the chapter within the film or
title of an inserted DVD/VCD/S-VCD directly by entering the number via the
number buttons on the remote control.
•
•
•
During playback press the number buttons on the remote control corres-
ponding to the chapter number – i.e. the 3 button for the third chapter.
With playback stopped press the number buttons on the remote control
corresponding to the title number – i.e the 3 button for the third title.
Playback of the chapter and/or title with the entered number now starts
automatically.
MPEG CD
SELECT:
Enter here a title number on the disc from where playback
should start.
Enter here a time position for the currently playing back
title from where playback should start.
GOTO:
Fast scan forward/backward
Direct chapter or time selection via the Search function (GOTO)
With fast scan you can select designated passages from the inserted
DVD/VCD/S-VCD during playback.
Note:
•
For fast scan forwards/backwards press the ꢃFAST FWD and/or ꢀFAST RWD
button repeatedly to set the following fast scan speeds:
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
to carry out functions that are not available the symbol
on the television screen.
will be displayed
Entry of the time position via search function DVD, VCD and SVCD:
• During playback press the GOTO button on the remote control. The time
menu is superimposed on the television screen:
MENU
Note:
TITLE
01 / 13
02 / 05
2 CH
CHAPTER
AUDIO
SUBTITLE
During fast scan no sound will be played back.
ENGLISH
ENGLISH
• To continue playback of the film at the selected place in normal
speed press, during fast scan the PLAY/PAUSEꢁꢂbutton.
BITRATE
50 IIIIIIII
TITLE ELAPSED 0:00:56
Slow playback forward (Slow motion)
• The entry field TITLE is automatically selected first. Press the ENTER button
and enter, with the number buttons, the desired title. On DVDs title 01 is
most often the main film.
To playback the contents of the inserted DVD/VCD/S-VCD in slow motion …
•
For slow playback forwards press the SLOW button repeatedly to set the
following playback speeds:
• Press the navigation button ꢇto select the entry field CHAPTER. Press the
ENTER button and enter, with the number buttons, the desired chapter.
• Press the navigation button ꢇto select the entry field AUDIO. Press the
ENTER button and select, with the navigation buttons ꢆꢇ, an audio language.
• Press the navigation button ꢇto select the entry field SUBTITLE. Press the
ENTER button and select, with the navigation buttons ꢆꢇ, a subtitle language.
• Press the navigation button ꢇto select the entry field ANGLE. Press the
ENTER button and select, with the navigation buttons ꢆꢇ, another camera
perspective (if available).
Note:
During slow motion playback no sound will be played.
• Press the navigation button ꢇto select the entry field TT TIME. Press the
ENTER button and enter, with the number buttons, the desired title time.
• Press the navigation button ꢇto select the entry field CH TIME. Press the
ENTER button and enter, with the number buttons, the desired chapter time.
• Press the navigation button ꢇto select the entry field REPEAT. Press the
ENTER button and select, with the navigation buttons ꢆꢇ, a repeat function
(see also repeat functions).
•
To continue playback from a selected position in normal speed, during
slow motion playback press the PLAY/PAUSEꢁꢂbutton.
Individual frame playback
To playback the contents of the inserted DVD/VCD/S-VCD in step motion,
during playback press the STEP button on the remote control. On the television
• Press the navigation button ꢇto select the entry field TIME DISP. Press
the ENTER button and select, with the navigation buttons ꢆꢇ, a time
presentation (see also superimpose disc information).
screen the symbol for step motion playback
appears.
•
•
Press repeatedly the STEP button to progress picture by picture.
To continue playback in normal speed at a selected point, press the
• To fade the menu out press the GOTO button again.
PLAY/PAUSEꢁꢂbutton.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Image enlargement (Zoom)
Change playback language
Note:
Note:
This function may not be available on all DVDs! If you attempt to execute
This function may not be available on all DVDs! If you attempt to execute a
a function that is not available, the symbol
screen.
is displayed on the television
function that is not available, the symbol
screen.
is displayed on the television
During the playback of an inserted DVD/VCD/S-VCD you can enlarge the
image on the television screen in three levels. For this press the ZOOM button
on the remote control to set the following enlargement levels:
With many films on DVD you can, during playback, select another playback
language by pressing the AUDIO button on the remote control.
The first press of the AUDIO button switches to the first available playback language.
With each further press of the AUDIO button other available playback languages,
one after the other, are switched on.
The currently switched on playback language will be superimposed on the
television screen.
Programmed playback (PROG)
With the control buttons ꢅꢁꢆꢇsections of the enlargement can be
suspended.
Note:
To switch off the enlargement function and return to the normal image
size press repeatedly the ZOOM button.
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
to execute a function that is not available, the symbol
television screen.
is displayed on the
Change camera aspect (ANGLE)
With the "Programme" function you can put together your own film programme
in so far as you can select only certain chapters of an inserted DVD/VCD/S-VCD
for playback. In this way you can determine for yourself the sequence, in which
the chapters are played back. You can compile a maximum of 20 chapters
of a film for programmed play.
Note:
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
•
Press the PROG button on the remote control during playback or when
Many films on DVD contain chapters which were recorded simultaneously
from various camera perspectives. With films that have such chapters
available you can view the same chapter from different perspectives.
For this press the ANGLE button on the remote control during playback of an
inserted DVD. Each press of the ANGLE button will switch to one of the
available camera perspectives.
playback is stopped.
The Programme menu will be displayed on the television screen.
Programme window
1
2
3
4
5
6
7
TT:
TT:
TT:
TT:
TT:
CH:
CH:
CH:
CH:
CH:
TT:
TT:
TT:
TT:
CH:
CH:
CH:
CH:
8
Superimpose/fade out subtitles
9
10
Note:
EXIT
This function may not be available on all DVDs! If you attempt to execute
a function that is not available, the symbol
screen.
is displayed on the television
First are listed the programme positions 1-10, programme position 1 is
highlighted.
If the film on the inserted DVD has subtitles available you can superimpose
these on the television screen during playback by pressing the SUBTITLE button
on the remote control.
1. With the number buttons enter the number of the title that is to be played
back first. The highlight changes to chapter entry (CH:).
2. With the number buttons enter the number of the chapter that is to be
played back. The highlighting moves to the programme position 2.
3. Select, with the navigation buttons ꢅꢁꢆꢇ, further programme positions
and enter title and chapter numbers for the programme positions.
• To display the next 10 programme positions select, with the navigation
buttons ꢅꢁꢆꢇ, the field ꢈand press the ENTER button.
You can allocate up to 20 programme positions.
With the first press of the SUBTITLE button the subtitle of the first available
language will be superimposed on the television screen. With each further
press of the SUBTITLE button the subtitles of other available languages will be
superimposed successively on the television screen.
The number of the currently superimposed subtitle language will be superimposed
on the television screen ( i.e. 1/10 for the first of ten available subtitle languages).
• To delete entries in a programme position select the programme position
and press the ENTER button.
When the last of the available subtitle languages is superimposed (i.e. 10/10
for the tenth of ten available subtitle languages) you can switch off the subtitle
function by pressing the SUBTITLE button again. OFF is superimposed on the te-
levision screen.
• To stop the programme function select the field EXIT and press the ENTER
button. All allocated programme positions are deleted.
4. You start playback of the programme positions by selecting the field
START and press the ENTER button.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
During the programmed playback the notice PROGRAM appears in the display.
To delete the programmed playback press twice, during playback, the STOPꢄ
button on the front panel of the DVD player or on the remote control.
TITLE
ALL
Select TITLE to continuously repeat the currently playing
back title until repeat playback is switched off or playback
is cancelled by pressing the STOP ꢄbutton twice.
Select ALL to continuously repeat all available titles on the
disc, thus the entire disc, until playback repeat is switched
off or playback is cancelled by pressing the STOPꢄbutton
twice.
Note:
If you are not sure what number a title and/or chapter to be programmed has
then select the corresponding chapter, during playback of the film, with the
buttons SKIP FWD
and SKIP BWD
and susequently press the DISPLAY button
RANDOM
Select RANDOM to play the titles on the disc in a random
order. This setting is available only when playing audio CDs.
on the remote control to superimpose all information from the inserted DVD/VCD/
S-VCD onto the television screen. Here you will find, amongst others, the current
title and chapter numbers.
To switch off repeat or random playback, during playback press repeatedly
the REPEAT button until no further displays appear on the television screen.
On this topic see also the section "Superimpose disc information".
Repeat function with MP3/WMA/MPEG/ JPEG/Xvid discs
During playback press the REPEAT button several times to apply the following
repeat functions (the set function appears in the display):
REPEAT ONE
Superimpose disc information
Note:
Endless repeat of the current title/image.
This function may not be available on all DVDs/VCDs/S-VCDs! If you attempt
REPEAT FOLDER
to execute a function that is not available, the symbol
television screen.
is displayed on the
Repeat the current folder. If a folder structure is not available all titles/images
on the disc and/or data carrier will be repeated.
RANDOM
With this function you can superimpose all the available information from
a DVD/VCD/S-VCD inserted into the DVD player onto the television screen
during playback.
Random playback of the titles on the disc and/or the data carrier.
•
For this, during playback, press the DISPLAY button on the remote control.
Repeat sequence (A–B)
On the television screen will be superimposed:
With this function you can repeat playback of a favourite sequence within
a chapter of the current playback disc.
With DVDs:
To do this …
• the current title number/the total number of titles
• the current chapter number/the total number of chapters
• the played back so far time in hours, minutes and seconds (TITLE ELAPSED)
• the time to the end of the film in hours, minutes and seconds
(TITLE REMAIN)
• During playback press the A – B button on the remote control as soon as the
desired sequence starts to playback.
A appears on the television screen.
• Press the A – B button again as soon as the end of the desired sequence is
played back. Pay careful attention to the fact that the start and finish of
the sequence must be located within a chapter.
• the played back so far time of the chapter in hours, minutes and seconds
(CHAPTER ELAPSED)
• the time to the end of the chapter in hours, minutes and seconds
(CHAPTER REMAIN)
AB appears on the television screen.
Repeat playback of the selected sequence begins immediately without you
having to press the PLAY/PAUSEꢁꢂbutton. The sequence will continuously re-
peat until you press the A – B button again in order to switch off the function.
With VCDs/S-VCDs:
Setting playback volume
• the current title number/the total number of titles
• the played so far time of the current playback title on the VCD/SVCD in
hours, minutes and seconds (SINGLE ELAPSED)
Press the VOL + button on the remote control during playback to increase play-
back volume or the VOL – button to reduce playback volume.
• the time to the end of the currently playing back title in hours, minutes and
seconds (SINGLE REMAIN)
To stop display of the disc information press repeatedly the DISPLAY button
until the notice DISPLAY OFF appears on the television screen.
Set the audio channel
Press repeatedly the L/R/ST button on the remote control to set one of the
available audio channels (LEFT MONO, RIGHT MONO, MIX-MONO or
STEREO) of an audio CD, S-VCD or VCD.
Repeat function for DVDs, VCDs, S-VCDs and audio CDs
With the repeat function you can…
Dimmer
Press the DIMMER button on the remote control to change the brightness of the
... in the case of DVDs, selectively repeat title, chapter or the entire DVD.
... in the case of VCDs/S-VCDs individual titles and/or the entire VCD/S-VCD
repeatedly playback.
display on the DVD player in three stages (Bright, medium, off).
... in the case of audio CDs, playback repeatedly a particular track and/or
the entire CD.
To switch on repeat playback...
• Press the REPEAT button several times during playback.
The repeat symbol
notifications:
CHAPTER
appears in the display with one of the following
Select CHAPTER to continuously repeat the currently playing
back chapter until repeat playback is switched off or play-
back is cancelled by pressing the STOP ꢄbutton twice.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
To switch playback sound to mute (MUTE)
• The area on the right is intended for the previewing of JPEG images.
A preview appears as soon as you highlight a JPEG file in the file window.
• At the bottom is located the information bar, in which is displayed the image
size (JPEG Image) as well as the medium (DISC, USB or CARD), on which
the files are located.
• Select a file with the aid of the navigation buttons ꢆꢇ. You confirm the
selection by pressing the ENTER button. The file will be played back and/
or the JPEG Photo displayed.
To switch the playback sound to mute press the (MUTE) button on the remote
control during playback of DVDs, VCDs/S-VCDs, audio CDs and CD-Rs/CD-RWs
with MP3 or WMA data. MUTE is displayed on the television screen.
When you want to switch the playback sound back on press the (MUTE) button
again or the VOL + and VOL – buttons. MUTE OFF or the corresponding volume
level is displayed on the television screen.
1. To open a folder select the folder and press the ENTER button. The contents
of the folder will be listed.
13. Playback of JPEG-Photo
CD/WMA/MP3/MPEG4
2. To reach a higher folder level select the symbol
with the entry ".." and
press the ENTER button.
Insert a storage medium into the DVD player. If you use a memory card or
USB stick press repeatedly the USB button until the desired playback source
is depicted.
The contents of the data carrier (CD, DVD, USB memory stick or memory card)
will be displayed on the television:
Playback of JPEG discs
• With the navigation buttons ꢆꢇhighlight an image and press the ENTER
button or the PLAY/PAUSEꢁꢂbutton to open the image.
The image is shown on the display
Subsequently change the view to the next available image on the disc/in the
folder.
Display of MP3 data
• To display the currently shown image press the PLAY/PAUSEꢁꢂbutton longer.
• To continue the playback press the PLAY/PAUSEꢁꢂbutton again.
• You can access an image directly by entering the image's file number with
the number buttons and subsequently confirm the entry with the ENTER button.
• With the navigation buttons ꢅꢁyou can rotate the image in 90° increments
during playback.
• With the navigation buttons ꢇꢆyou can mirror the image horizontally
or vertically during playback.
• During playback press the STOPꢄbutton to display a miniature view of all
images in the folder/on the disc. 12 miniatures will be displayed on each
page.
00:23
001/058
03:56 160 Kbps
\ music
..
01 track01
02 track02
03 track03
04 track04
05 track05
06 track06
DISC
DISC
DISC
• Select with the navigation buttons ꢅꢁꢆꢇan image and start playback
with ENTER or PLAY/PAUSEꢁꢂ.
• Select with the navigation buttons ꢅꢁꢆꢇone of the following entries
Display of JPEG data
00:00
001/037
00:00
from the bottom display lines and confirm the entry with the ENTER button.
\ pictures
Slide Show
Menu
Starts a slide show of the images in the folder/on the disc
Shows the available button functions for JPEG playback.
Press the ENTER button until this menu has faded out.
switches to the previous page
..
picture 01
picture 02
picture 03
picture 04
picture 05
picture 06
Prev
Next
switches to the next page
• Press the MENU button to switch to the file list again
Selection of slide show transitions:
Display of AVI and MPEG data
You can select different transitions for changing from one image to the next.
WIPE TOP, WIPE BOTTOM, WIPE LEFT, WIPE RIGHT, DIAGONAL WIPE
LEFT TOP, DIAGONAL WIPE RIGHT TOP, DIAGONAL WIPE LEFT BOTTOM,
DIAGONAL WIPE RIGHT BOTTOM, EXTEND FROM CENTER H, EXTEND
FROM CENTER V, COMPRESS TO CENTER H, COMPRESS TO CENTER V,
WINDOW H, WINDOW V, WIPE FROM EDGE TO CENTER and NONE.
• During the slide show press the PROG button until the name of the desired
transition appears in the upper left corner of the television screen.
00:00
001/006
00:00
\ videos
..
video 01
video 02
video 03
video 04
video 05
video 06
• The data is listed on the left (Data window). Folders will be depicted with
the symbol
.
• To superimpose the folders available on the disc press the PROG button
repeatedly until the notice FOLDER appears at the bottom of the display.
• Press the PROG button again repeatedly until the notice FILELIST appears at
the bottom of the display. Folders will now be faded out and all data on
the disc is represented in a list.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
A window appears, in which is displayed the copying process with a
progress bar.
14. CD Ripping function
With the DVD player you can transfer music and speech files in the format
.cda (CD Audio) or from a disc onto a USB memory stick. Thereby files in
the MP3 format will be saved onto the USB memory stick.
CD RIP
Ripping
Selected
TRACK
TRACK Progress
track01
track02
track03
track04
track05
track06
track07
28 %
04:43
04:09
04:49
00:53
01:08
05:00
Note:
Total Progress
CANCEL
When transfering audio files to a data carrier be aware of the existing copyright
laws and regulations! Make sure that you are producing copies for private
use only and do not violate applicable laws!
SUMMARY
Now ripping
TRACK
01 / 16
CD RIP
OPTIONS
Normal
128kbps
TRACK
track01
•
To prematurely abort the copying process select the input CANCEL and
confirm with the ENTER button.
Speed
Bitrate
04:09
04:43
04:09
04:49
00:53
01:08
05:00
track02
track03
track04
track05
track06
track07
Create ID3 Yes
Device USB
Attention!
Never remove the USB memory stick from the USB port during copying!
Otherwise it could lead to data loss on the storage medium.
SUMMARY
Selected
Selected
TRACK
Time
0
00:00
Note
Start
Exit
Select all
Select none
On the memory medium the index RIP_001 will be applied for the MP3 files.
For each further copy process of a new CD another index RIP_002, RIP_003
etc. will be applied.
• Place an audio CD into the disc tray.
• Insert a USB memory stick into the USB port.
• Whilst playback is stopped press the MENU RIPPING button on the remote
control. The menu depicted above appears on the television screen.
• To set the various selection possibilities press repeatedly the ENTER button.
15. Cleaning of the DVD player
Speed
Select this menu input to set the speed of the transfer either
to Normal or Fast.
Clean the housing of the DVD player with a slightly damp cloth and a mild
cleanser only. When cleaning, make sure that no moisture gets into the DVD
player!
Clean the inside of the disc tray, if necessary, exclusively with a clean dry
brush (i.e. a lens brush obtainable from a photographic dealer).
Never clean the inside of the disc tray with anything moist!
Bitrate
Select this menu input to set the MP3 quality. Possible bitrates
are 96 kbps, 112 kbps and 128 kbps. A higher bitrate
will result in a larger
MP3 file on the data carrier after copying.
Select this menu input to automatically create an ID3 tag
for the MP3 files.
Create ID3
Warning!
• Select, with the control buttons ꢅꢁꢆꢇ, a title from the
Title list and confirm with the ENTER button. The title will be marked with
a tick. In the same way you select further titles for copying in MP3 format.
• To mark all titles for copying in MP3 format select, with the control buttons
ꢅꢁꢆꢇthe input Select all and confirm with the ENTER button.
All titles will be marked with ticks.
Moisture penetrating into the DVD player creates the risk of an electric shock!
The DVD player may also be irreparably damaged!
16. Disposal
• To cancel the marking of all titles select, with the control buttons ꢅꢁꢆꢇ, the
input Select none and confirm with the ENTER button. The markings will be
deleted.
• To start the copying process select, with the control buttons ꢅꢁꢆꢇ,
the input Start and confirm with the ENTER button.
Disposing of the device
Do not, under any circumstances, discard the device in the household
refuse. This product is subject to the European directive 2002/96/EC.
• To exit the CD-Ripping function select, with the control buttons ꢅꢁꢆꢇ,
Dispose of the device through an approved disposal centre or at your community
waste facility.
the input EXIT and confirm with the ENTER button.
Observe the currently applicable regulations. In case of doubt, please contact
your waste disposal centre.
Disposing of batteries!
Do not dispose of the batteries with household waste. Every consumer is legally
obliged to dispose of batteries at a collection site in his community/city district or
at a retail store.
This obligation is intended to ensure that batteries are disposed of in an
environmentally friendly manner.
Only dispose of batteries when they are fully discharged.
Disposal of packaging
Dispose of the packaging materials in an environmentally responsible
manner.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Troubleshooting
C
Check whether the settings in the OSD menu match the connection option
you have used to connect the audio components to the DVD player.
For this see chapter 9. "Connecting an audio component to the
DVD player".
Display is blank/DVD player shows no functions even though it is
switched on
A
Check to see that the power cable is inserted properly into the power
socket.
Check to ensure that the power socket in which you have plugged the
power cable of the DVD player is live by connecting another device to
it. If necessary plug the DVD players power cord into another power
socket.
D
E
Using the television's instruction manual check to see if current settings to
the television are necessary in order to use the DVD player with the tele-
vision.
Check by means of the operating instructions for a potential connected
audio component if settings to it are necessary in order to use it with the
DVD player.
B
C
Check to see that the display dimmer function is switched off.
To do this press the DIMMER button on the remote control.
Switch off the DVD player by activating the POWER switch and then wait
ten seconds. Then switch the DVD player back on by activating the POWER
switch again.
F
•
If you …
have connected the DVD player to a stereo television and have not
connected an audio component to the DVD player or
have connected a Dolby Prologic compatible audio component via the
analogue stereo outlet (via cinch cables to the cinch sockets L and R)
of the DVD player:
D
•
The display shows "NO DISC" even though there is a disc inserted
Check to see that you have selected in the OSD menu AUDIO with the
menu input FRONT SPEAKER the setting LARGE.
A
The disc is dirty, scratched or damaged. Clean the disc or insert another
disc.
B
The Country/Region code on the inserted DVD/VCD/S-VCD does not
correspond to the Country/Region code of the DVD player. In this case
the DVD/VCD/S-VCD cannot be played with the DVD player.
No 4:3 or 16:9 image
A
Check by means of the televisions operating instructions, which image
formats the television has at its disposal.
B
Check to see if the settings in the OSD menu match the available image
format of the television.
Inserted disc will not playback
It is possible that a layer of condensation has built up on the DVD players laser
scan lens. This can be the case especially if the DVD player has been subjected
to strong temperature fluctuations.
If this is the case place the DVD player in a dry environment at normal room
temperature. First remove the currently inserted disc from the disc tray.
Then leave the DVD player switched off for at least one hour without using
until the condensation film has evaporated.
Remote control not functioning
A
B
C
Check to make sure that the remote control batteries have been inserted
into the battery compartment with the correct polarity.
Check to see if the remote control batteries are exhausted and, if necessary,
change both batteries.
Make sure that there are no obstacles located between the remote control
and the DVD player.
No image or Black/White image only
D
Remain within five meters of the DVD player when using the remote control.
A
Check to make sure that all connection cables between the DVD player
and the television (or Video projector) are firmly inserted into the
corresponding sockets
Playback language/ Subtitle language do not correspond to the
settings in the OSD menu
B
Check to make sure that the settings in the OSD menu match the connections
variant, with which you have connected the DVD player to the television
(or Video projector).
The playback language/Subtitle language setting in the OSD menu is not
available on the inserted disc.
One or several functions can not be switched on
For this see chapter 8. "Connecting the DVD player to a television".
The selected functions may not be available on all DVDs/VCDs/S-VCDs!
C
Check by means of the televisions (or Video projectors) operating
instructions to see if settings to the television (or Video projector) may
be necessary in order to use the DVD player with the television.
If you attempt to execute a function that is not available, the symbol
displayed on the television screen.
is
None of the buttons on the device or on the remote control are
functioning/other malfunctions
No sound
A
Check to see if the television and/or DVD player have possibly been
A
Switch off the DVD player by pressing the POWER switch. Wait ten seconds
switched to mute.
and then activate the POWER switch again to switch the DVD player on
B
Check to see if all connection cables between the DVD player and potentially
connected audio components are plugged firmly into the corresponding
sockets.
once more.
B
In the event that the malfunction is still present: Reset the DVD player to
its default settings.
For this see chapter 10.6 "Setup menu PREFERENCE".
Contact one of our service partners in your area if …
•
•
the stated function defect can not be resolved as described or
other functional defects arise.
For this see chapter 19 "Warranty and service".
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite video
18. Glossary / Key Word Index
Video signal or FBAS signal; thereby it involves an image signal, in which
colour and brightness information are included at the same time.
What are DVDs, VCDs and S-VCDs?
Progressive scan
In the normal way TV devices and Video projectors are controlled with so
called "Half images". Thereby clearly visible line structures develop. Contrary
to this, Progressive Scan denotes the output of full images (with this DVD player,
at the output YPbPr) Progressive Scan signals can only be processed by play-
back devices equipped for this purpose (in particular large screen televisions
and projectors). The image quality as opposed to traditional image signals is
considerably higher.
DVDs
DVD is the short form for "Digital Versatile Disc". DVDs are a storage medium
for audio and video data; they are available in 8 cm and 12 cm (Diameter)
formats. Because of the much higher storage capacity as compared to CD-Rs/
CD-RWs DVDs can provide a playback duration of up to eight hours for the
audio and video data stored on them.
VCDs/S-VCDs
YUV (component video out)
"Video CD" (VCD) and "Super Video CD" (S-VCD) are designations for two
processes of compressed storage, thus space saving, of films on CDs. VCDs
and S-VCDs are available in 8 cm and 12 cm (Diameter) formats. Their storage
capacity is a great deal lower than that of DVDs. For this reason they only
offer a playback duration, for the saved audio and video data on them, of
20 minutes (8 cm format) and/or 74 minutes (12 cm format).
VCDs are available in two versions:
YUV indicates the component signal, which with this device is available at the
output YPbPr in the form of so called "Half images"; as a rule this is the best
signal for the control of large screen televisions and projectors, which can not
process Progressive Scan signals. As with the RGB image transmission, YUV is
comprised of three separated image signals:
•
•
the brightness signal "Y" and
the two colour diferential signals "U/Pb" and "V/Pr"
•
Only audio and video data can be played back on version 1.1
VCDs/S-VCDs.
Half images (Interlace)/Full images (Progressive Scan)
•
PBC (Playback control) functions are available on version 2.0 VCDs/
S-VCDs. In addition still images can be played back in a higher resolution.
A standard television image is comprised of 576 visible lines; at first all odd
and then all even image lines are displayed alternatively, thus each displays
a half image. Thereby only 25 full images (50 Half images) can be displayed
per second. This technique is designated as "Interlace" format.
Playback Control (PBC)
Version 2.0 VCDs/S-VCDs have Playback Control (in short "PBC") at their disposal.
Then on the VCD/S-VCD a main menu is available, by which various functions of
the VCD/S-VCD are allowed to be operated.
Contrary to this with the so called progressive or "Progressive Scan" format
all image lines are displayed every time, that is to say 50 full images per
second are displayed. Thereby increasing the total quality of the images, still
images and text for example appear sharper.
What are Title and Chapter?
Title is the name given to the largest units of image and sound units on DVDs;
on many DVDs the (Main) film has the title number 01. For bonus material
(i.e. Film trailer, background information etc.), that is available on many DVDs,
other possible title numbers can be used.
HDMI
HDMI is short for "High Definition Multimedia Interface" and refers to a 19
contact interface for complete digital transmission of audio and video data.
With its high bandwidth HDMI handles all known today home electronics
digital video and audio formats. HDMI transmits audio data up to frequencys
of 192 kHz with text widths of up to 24 Bit on up to 8 channels. Thus not
only all of today's image and sound formats introduced into home electronics
including HDTV (up to the highest present resolution of 1080i) are transmitted
without loss of quality but also future formats with yet higher resolutions.
Chapter is the name given to the next smaller image and sound units beneath
title. If the DVD/VCD/S-VCD or its title is divided into chapters, numbers are
assigned to you, through the input of which the chapter can be selected direct.
Bear in mind that not on all DVDs …
•
•
are the DVD or the title divided into (numbered) chapters
Chapters are also designated as "Scenes" (i.e. in the main menu of DVDs)
Decoder
The sound on DVDs with home theatre sound is saved on the DVD in encrypted
(encoded) form. Different encryption formats exist for several purposes, for
example AC-3 for the playback of Dolby Digital Surround Sound.
In order to playback encrypted sound, the playback device (i.e. the DVD
player) and/or the audio component connected to it (for example Surround
system) must be equipped with a so called decoder, which converts the
encrypted signal back into music and/or sound.
What are Scart, S-Video, Composite-Video Progressive
Scan, YUV and HDMI?
Scart
Scart denotes a 21 pole standardized plug connection, via which the RGB
signal, video signal and S-Video signal as well as a number of control and
auxiliary signals are transmitted.
The Silvercrest SHDP 5.1 A1 DVD player is equipped with an AC-3 Decoder
(for Dolby Digital 5.1 Surround Sound signals).
S-video
When the DVD player is connected to a television via S-Video the brightness
and colour signals are transmitted seperately; in this way a greater image
sharpness and a reduced so called "Colour noise" is achieved.
Colour noise refers to the overlaying of the colours, mostly heavily saturated
parts of a video image, through an irregular, restive breakdown structure.
Dolby Surround
Dolby Surround is an analogue sound format, by which the two channels of
a stereo sound signal are used in order to accommodate room sound information
for further channels. Dolby Surround decoders convert the signals back into
sound or music and send the audio to two additional speakers that are situated
behind the listener.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Dolby Prologic
MPEG
In comparison to Dolby Surround sound format, with Dolby Prologic an additional
channel in the stereo signal is used; this is the so called "Centre" channel. The
corresponding centre loudspeaker is to be situated in the middle between the
stereo loudspeakers. The deepest sounds are fed to a bass loudspeaker, the
so called "Subwoofer". The subwoofer can be placed in any desired location
in the room; the logic for this is that the bass sounds that the subwoofer puts
out can scarcely be localized exactely by the human ear
MPEG ("Moving Picture Experts Group") refers to a video compression format.
USB memory sticks
The term USB memory stick refers to a plugable USB device, which is approximately
the size of a cigarette lighter. The expression is only colloquial and not a designation
for a type of product. For the most part with this expression is meant a USB
device that serves as an interchangeable storage media.
Dolby Digital (5.1)
What are folders?
Dolby Digital, also designated as AC3, is a digital sound format, by which up
to six seperate audio channels can be transported. With most of the current
DVDs, the sound is stored in the so called "Dolby Digital 5.1" format; the "5"
in the name "5.1" stands for the three front and two rear surround sound
channels, the "1" stands for the subwoofer channel.
As opposed to audio CDs the title on a CD-R/CD-RW with MP3, WMA or
JPEG files can be stored in folders, for example, in order to file titles from
different genres.
The structure of an MP3-CD can, for example, appear as follows, if the MP3
files are stored in folders:
DTS
FOLDER
MP3
MP3-CD
DTS is the abbreviation for "Digital Theatre System" and denotes one of the
most common surround sound formats for DVDs. As with Dolby Digital 5.1,
DTS uses three front and two rear surround sound channels as well as a bass
sound channel.
What are PAL and NTSC?
PAL
PAL is the abbreviation for "Phase Alternation Line". PAL is the mid and west
Europe (Exception: France = SECAM) customary and widest distributed colour
television standard.
NTSC
NTSC is the abbreviation for "National Television System Committee". NTSC
is a colour television standard that is primarily used in the USA and Japan.
19. Warranty and Service
Audio CDs
The warranty for this appliance is for 3 years from the date of purchase. The
appliance has been manufactured with care and meticulously examined be-
fore delivery. Please retain your receipt as proof of purchase. In the event of
a warranty claim, please make contact by telephone with our Service Depart-
ment. Only in this way can a post-free despatch for your goods be assured.
The warranty covers only claims for material and maufacturing defects, but
not for transport damage, for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for private use only and is not
intended for commercial use. The warranty is void in the case of abusive and
improper handling, use of force and internal tampering not carried out by our
authorized service branch. Your statutory rights are not restricted in any way
by this warranty.
Audio CDs contain exclusively audio data; they are also available in 8 cm
and 12 cm (Diameter) formats. The playback duration for the audio data stored
on them amounts to 20 minutes (8 cm format) and/or 74 minutes (12 cm format).
Audio data is stored on audio CDs in CDA format.
MP3
MP3 denotes a process and/or format developed by the Fraunhofer Institute
for the compression of audio data. In the MP3 format compressed music pieces
are only a fraction of their original size, which, for example, on CD-Rs/CD-RWs
allows for storage of a considerably greater volume of music than on com-
mercially available audio CDs, on which audio data is stored in the CDA format.
The warranty period will not be extended by repairs made under warranty.
This applies also to replaced and repaired parts. Any damage and defects
extant on purchase must be reported immediately after unpacking the appli-
ance, at the latest, two days after the purchase date. Repairs made after the
expiration of the warranty period are subject to payment.
WMA
WMA ("Windows® Media Audio") is a data format developed by Microsoft®
for audio data.
JPEG
JPEG ("Joint Photographics Expert Group") denotes a wide spread graphic
format, developed by the organization with the same name, with which
image data of the colour and grey scales are compressed.
20. Importer
KOMPERNASS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
DVD Player SHDP 5.1 A1
IAN 64329/64330
In order to guarantee a cost free repair procedure please
get in touch with the service hotline. Make sure you have
your sales slip handy.
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
E-Mail: [email protected]
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
Sender, please write clearly:
Last name
First name
Street
City/Town
Country
Telephone
Date/Signature
Description of the defect:
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|