Automatic Washing Machine
SIG100-97
Please check if the power receptacle is earthed
reliably before usage to guarantee your safety.
Please read this manual carefully before use.
The manufacturer is not responsible for any
risks occurred owing to disobey these
stipulations.
Please retain it attentively for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of the parts
Softener injection inlet
Door switch
Bleach injection inlet
Top lid
Control panel
Cold water inlet valve
Hot water inlet valve
Inner tub
Agitator
Water absorption cushion
Cabinet
Power line
Control panel seat
Drain hose joint
Adjustable feet
(4)
Accessories
Meaning and description of the symbols
Contents marked with that symbol
are related to the safety of the
Warning sign
Water inlet hose
(2)
product and the personal safety
of the users. Please operate in
strict conformity to the contents,
otherwise it may cause damage
of the machine or injure the
personal safety of the user.
Outer drain hose component
(1)
Contents marked with that symbol
Forbidding sign
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or injure the personal safety of
the user.
Drain hose hook
(1)
Drain hose clamp
(1)
Please understand the shapes of the washing machine and accessories may be different
from the sketch figures in this manual due to product improvement.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Please insert the power cord into special three The power cord plug should be convenient
-phase receptacle.The earthing terminal of the to be pluged in or pluged out with hand
receptacle must be earthed reliably.If possible ,while the washing machine runs normally.
please adopt electric leakage protector.
Be sure to pull the plug out and close the
water tap when the machine is idle,when
moving the machine,or when cleaning
the machine.Do not use wet hand to ins-
ert or pull out the power plug.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe
with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced
by the technicians of our special shop or the after-sale service department.
Do not put the machine at damp place like the bath
room. Never wash it with water.Not put wet laundries
on the control panel.
Do not use water hotter than 60
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Do not decompose, repair or alter the
machine by yourself.
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
Petrol
nner
Thi
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
To prevent your laundries and washing
machine from damage,be sure to take
out all of the foreign materials from your
pocket,such as coins,buttons,sand or
hair pins etc.
Before washing,please check if the water
tap is open ,and if the water inlet pipe is
connected properly.
It is suggested to use low-foaming was-
hing powder
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Adjust the installation position
The largest allowed slope of the base of the machine is 2 . The slanting or rough
ground will result in unstable running or stoppage of the machine. Please adjust
it with following methods:
Adjust the adjustable foot:
To twist the adjustable foot, please first lift up
the side of the foot slightly, and twist the foot.
Confirm it's horizontal:
Hang the lead line to confirm
if it is horizontal.
.
Adjustable foot
High
Low
Install the drain hose
Put the drain hose clamp on the outer
drain hose, insert the outer drain hose
into the joint, and then clutch tightly
with drain hose clamp.
Drain hose
Drain hose clamp
Drain hose joint
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.put the drain hose up to suitable position.
1.0m-1.5m
2.Do not step on or press the drain hose.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the water inlet hose
1. Respectively attach the water inlet hoses to the hot water faucet and the cold
water faucet. Using pliers, tighten the coupling. ( As figure 1)
NOTE: Do not over tighten. Damage to the
valves can result.
2. Connect the hot and cold water inlet hoses to the hot and cold
water faucet.
Figure 1
3. Connect the other ends to their respective cold and hot water inlet valve
located at the rear of the washer
Jointer of the water inlet hose
C
C
H
H
Jointer of the
water inlet valve
Water absorption cushion
Figure 2
Note:
Hot water needs to be at a temperature of at least 120 F- 140 F.
(49 C-60 C)for the soap to dissolve and to avoid soap residue
remaining on clothes.
Check the connection between the water inlet
hose and the water tap
1.Swaying the hose gently to confirm if it is fastened
stable.
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the water inlet hose and the water tap, is firm,
so as to prevent dropping from improve Installation
position.
Take down the water inlet hose
1.Close the water tap.
2. Pull off the water inlet hose from the water tap and washer
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation before washing
Preparation before washing
1.Connect the water inlet hose. Open the water
faucet.
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. The earth terminal shall not link to
gas pipeline and faucet water pipeline.
3.Put the drain hose up.
1.0m~1.5m
Pay attention to followings before washing the laundries
Confirm if
Clear the pocket. Fasten the
The big laundries When the pulsator
there's special Take out the
requirment for coins , sand,
the laundries. hairpins etc.
buttons and
zippers.
like the jeans
shall be put in
loosely.
is running , the
buttons of the
laundries may
cause noise. For
t h e s a k e o f
carefulness,please
put the laundries
with buttons into
other laundries.
a.Please check if the laundries are applicable for washing.
b.Separate those not colorfast from other laundries.
c.For laundries not water absorbing,please put them into water with hands.
d.For laundries with much soil,please remove the soil first.You can add detergent on the
part with serious soil directly.It is much easier to remove the soil by that mean.
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before
putting them into the water.
f.Do not put the laundries polluted with chemicals directly into the washing machine.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Put in the laundries
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that
can be washed or spined in one time. Lau-
ndries quantity in one washing cycle shall
be lower than the rated capacity. The larg-
est capacity of this machines is 8.5kg.
The thickness, size, type of the cloth will
influence the actual washing capacity. It
is suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.
Do not select high water level for laundries
less than 4.0kg, so as to avoid splashing
of water.
Usage of detergent
How to use the washing powder
Direct dissolved in the machine
1.Fill water to "1" water level.
Washing powder
2.Add the power. Run for 30 seconds to dissolve it completely.
3.Put in the laundries. Select suitable water level.
The instant dissolving of the washing powder:
1. Prepare warm water of 30 and a container.
2. Add the powder while stirring to fully dissolve it.
The powder is more prone to pollute the laundries than the detergent.
Therefore please use it with proper quantity.
It is suggested not to use high sudsing detergent.
Different washing powders have different dosage. Please refer to the usage
manual of the washing powder for the details.
How to use the liquid bleacher
Procedures
Bleacher
1.Check clothing care labels for special instructions
2. Measure liquid bleacher carefully, following instructions on the bottle.
3. Before starting the washer, pour measured amount of bleach directly int
bleach dispenser. Avoid splashing or over-filling dispenser.
Note
Never pour undiluted liquid chorine bleacher directly onto clothes or int
the inner tub.
Bleacher
dispenser
Do not pour powdered bleacher into bleacher dispenser.
Do not mix chlorine bleacher with ammonia or acids such as vinegar and/or
rust remover. Mixing can produce a toxic gas which may cause death.
Inner tub
How use the fabric conditioner
Fabric conditioners help make clothes softer and fluffier and reduce static so that
clothes do not cling to you when you are wearing them.
Procedure
1. Carefully follow the instructions on the fabric conditioner bottle or packet.
2. Mix conditioner with an equal amount of warm water but only mix enough to
fill to the line marked inside the cup.
4. Pour the mixed conditioner into the cup in the top of the agitator. The
conditioner will automatically be dispensed before the deep rinse cycle
Fabric
conditioner
Note:
Agitator
Do not spill the conditioner onto the clothes because it may stain them.
Do not overfill the cup in the top of the agitator because the conditioner
may mix with the detergent and stain your clothes.
Do not stop the washing machine during the spray rinse cycle when using
a fabric conditioner.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Usage of the Operation Buttons
Explanation of Buttons
Indicator mode and meaning
Delay/Start button
Pushing the button to select the reserve washing
time from 2 hour to 24 hour.
During no delay, the Delay/Start indicator is
off, the remainingtime indicator ison, and
the nixie indicator displays the non-delayed
cycle remaining time.
The indicator is off, indicating that the
program or mode is not selected
Fabric
conditioner
The indicator is on, indicating the program
or mode selected and about to run
Flashing
Normal running mode
Time Remaining
Time On
Normal/Fast
Normal/Slow
Delicate/Fast
Delicate/Slow
Delay
Stain Wash
Start
Heavy
Normal
Normal
Speed
Light
Wash/spin
Heavy Duty
Load Size
Cycles
Soil Level
Whites
Speed wash/spin button
Cycles button
Select following six automatic programs
with the button
Push the button to select the spinning speed
when program is
Select the spinning speed
normal or delicate casual.
Whites
Washing the cotton textile
Heavy
Duty
Washing the bigger, thicker or
heavier dirty laundries
Normal
Common washing
Quick
wash
Delicate Washing the woollen textile
Quick washing of the light dirt
laundries
Casual
Hand
Wash
or underwear
To imitate hand scrub
washing effect
For setting, changingwater level andmanually
replenishing water. Water levels may be setat
beginning or pause.
During Soak, Wash or Rinse, press this button
to manually replenishwater and releaseit to
stop. But thisfunction is disabledwhen water
reaches overflow protectionlevel.
Soil level button
For selecting clothessoiled degree.
Wash cycle increases 2 minutesfor a
next higher soileddegree and decreases
2 minutes fora next lowersoiled degree.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Start/Pause button
Numeral tube s window
After switch on the power, push
it once to start the washing machine
In operating, push the button to pause
the operating.
In pause, push the button to resume
operating.
To indicate remaining min. during
program running.
To indicate remaining reservedhr.
during reservation period.
To indicate fault symbolsfor
abnormal conditions.
Power On/Off button
Push the button once to switch on the power.
When the power is on, push the button once
to cut off the power.
Power
On/Off
Louder
Softer
Off
Soak
Wash
Hot/Cold
Start
Pause
Rinse
Warm/Cold
Quick wash
2ND Rinse
Cold/Cold
Spin
Cycle
Signal
Temp
Wash/Rinse
Delicate Casual
Process
Hand Wash
Process button
Cycle Signal button
For selecting processes. Soak
process is Invalidif Hand wash,
Delicate Casual orQuick Wash
program is selected;
For selecting louder, softer oroff
buzzer volume.
Water level indicator turns offif only
Spin is selected.
After selecting aprogram, press
Process to select 2ND Rinse the
machine will includean additional
rinse process.
For selecting inlet water temperature
during wash and rinse.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
b Operating procedure
Time Remaining
Normal/Fast
Power
On/Off
Time On
Normal/Slow
Louder
Softer
Off
Soak
Wash
Rinse
Delicate/Fast
Delay
Stain Wash
Hot/cold
Start
Start
Delicate/Slow
Heavy
Warm/Cold
Cold/Cold
Pause
Normal
Quick Wash
2ND Rinse
Spin
Normal
Light
Speed
Cycle
Signal
Wash/Spin
Temp
Wash/Rinse
Heavy Duty
Delicate Casual
Load Size
Soil level
Cycles
Process
Whites
Hand Wash
Power
On/Off
1. Press Power On/Off to switch on the power supply
Upon switching onthe power, the computer boardbuzzes once andthe unit
enters from standbyto working status, i.e. initial status(Normal program);
5 minutes afterswitching on, if Start/Pause button isn'tpressed, the unitwill
automatically switch off and returnto standby;
The unit returns to standby immediately after completion of a program;
Pressing Power On/Off button, allprograms will stopand the unitenters standby,
regardless of thecomputer conditions (start, pause, alarm etc.).
The washer hasintelligent wash resumption. After thepower is cutoff abnormally,
the washer couldresume working atstoppage while thepower resumption.
Buttons initial status for Normal program
Cycle Signal
Softer
Temp Wash/Rinse
Warm/Cold
Soak, Wash, Rinse, Spin
Process
Cycles
Normal
Nixie display
Soil level
Remaining min. of the present cycle
Heavy
6
Load Size
Speed Wash/Spin
Normal/Fast
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press the button of cycles to select a suitable
full-automatic program.
Cycles
After switching on, the Normal program will be the default. If other
full-automatic program is desired, you can press the button of cycles
to get the corresponding indicator on. Refer to button of cycles on
page 8.
Page 8
Example: Use the Quick program for slightly soiled articles
When Normal program is selected,
the washing machine will perform
full-automatically controlled fuzzy
program to set water level, water flow
and wash duration according to the
cloth nature and weight.
Quick Wash
Delicate Casual
Hand Wash
Cycles
,
Buttons status for different program selected
Normal Heavy
(with soak)
Hand Delicate Quick
Wash Casual
Wash
Cycles
Whites
Duty
Cycle Signal
Temp Wash/Rinse
Process
Softer
Softer Softer
Softer
Softer
Softer
Warm/Cold
Warm/Cold
Hot/Cold Cold/Cold
Warm/Cold
Warm/Cold
Wash, Rinse, Spin
Nixil Display
Soil Level
Load Size
Speed
47
63
52
39
37
25
Heavy
Heavy
Light
Normal
Normal
Stain Wash
Slow
Fast
3. Press the button of Process to select suitable
processes.
Process
After the power is switched on, the washing machine will automatically set
a normal program comprising of processes of Wash, Rinse and Spin . If other
process combination is desired, press the button of Process to select one or
several process of soak, wash, rinse and spin. Refer to the paragraph of
processes selecting.
Page 9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Spin shall begin after some time even
there is no water in the tub
Do not use soak process for woolen
articles.
Clothes prone to fade and other clothes
shall be separately washed.
Load Size
4. Press the button of Load Size to select a suitable
water level.
After switching on the power, the washing machine detects the load, and then
automatically sets a water level. If other level is wanted, press the button
Water level to select. Please refer to Button of 'Load Sizel'
on page 8.
Page 8
5. Press the button of Speed to select suitable wash
and spin speeds
Speed
Wash/Spin
After the power is switched on, the washing machine will automatically set as
Normal/Fast . If the user desires to change it, press this button to select
according to Speed on page 8.
Page 8
6. Press the button of Soil to suit differently
soiled clothes.
Soil Level
After the power is switched on, the washing machine automatically sets at
Heavy , the user may judge the clothes soil degree and select with the
Soil level button himself. See Soil on page 8.
Page 8
Temp
7. Press the button of Temp. Wash/Rinse to select
different washing temperatures.
Wash/Rinse
After the power is switched on, the washing machine will automatically set at
Warm/Cold . The user could also set three wash conditions of hot, warm and
cold. Refer to Temp. Wash/Rinse on page 9 to select.
Page 9
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle
Signal
8. Press the button of Cycle Signal , which will
accordingly remind you of the cycle completion.
After the power is switched on, the washing machine will automatically set
at Softer . The user himself could also set three warning volumes Louder,
Softer or Off for the completion of a cycle. Refer to Cycle Signal
Page 9
on page 9 to select.
9 Press the button of Delay/Start to select a suitable Delay
Start
reserve wash program
After switching on, the washing machine reserved wash program will be
automatically set inactive. If you desire a wash cycle to end at a reserved
time, you can press the Delay/Start button to set a reserved wash program.
Refer to The button of 'Delay/Start' on page 8.
Page 8
Confirming a reserved program
When delay starts, program selected indicator turns off, while
the delay Indicator and remaining time turn on. During
reservation period, pressing Delay/Start button could
get reservation conditions displayed.
The wash cycle will end after 18 hrs
Start
Pause
10. Press the Start/Pause button
Press this button when you want the machine to start running.
During machine running, press this buttonto pause andpress once againto
resume operation.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the top lid
If you open the top lid, the machine
will stop working except for water
filling and draining water
Finish Washing
After Finishing wash
alarm automatically
The power will be switched off automatically after the finishing of the washing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
After washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise
it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using
1.Take off thelint filter
Pull up thelint filter onthe agitator
to remove. As shown inFigure 1.
Lint filter
Press
Press
Pull up out
Agitator
2.Removing lint
Press the lintscreen clip withyour
thumb and indexfinger, andget the
screen downward asshown in Figure
2. While wet, remove the linton the
screen in water.
Figure 2
3.Mounting thelint filter
After cleaning, mount the screenback
onto the lintfilter as shownin Figure 3.
Then put thelint filter backin the agitator
barrel.
Lint Screen
Figure
Figure 3
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
The filter screen of the
water inlet valve is likely
to be blocked by foreign
materials and influence
the water inlet. Please
clean it with brush every
two months.
Do not wipe it with thinner, petrol, alcohol etc.
l
Petro
inner
Th
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after
each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for
some time (about 1 hour), then close the top lid.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending it to
repair. If there are real breakdowns, please come to the special maintenance department
or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The reason
How to settle
After the "reserve" is started,
it rings and the digital tube
displays "E0"
Close the top lid
The top lid is not closed
The draining does not work,
or the speed of draining is
too slow. The digital tube
displays "E1" and it rings.
Is the drain hose blocked by
foreign material?
Clean the foreign material. Open
and close the top lid once.
It stops running during wash,
rinse or spin. The digital tube
displays "E2" and it rings.
The top lid is not closed
Close the top lid
It does not do water inlet or
the speed is slow (the water
level is not reached after 15
minutes). The digitaltube
displays "E4" and it rings.
Open the waterfaucet. Open
and close thetop lid once.
Is the water faucet open or is
there water supply failure?
Is the water inlet valve is
blocked
Clean the waterinlet valve.Open
and close thetop lid once.
Use it when the power is on.
Insert the power plug tightly.
Is there power failure?
Is the power plug loose?
The machine does not act.
(the indicators are off.)
Is the machine slanting?
Level the machine properly.
Fasten the buttons and zipper
Is there metal material inside
the washing machine?
Are the laundries slanting in
spinning?
There's abnormal sound
inside the machine.
Re-order the laundries. Close the
top lid.
Is the jointer of the water inlet
hose is loose or twisted awry?
The water faucet leaks.
No water filling
Fasten the jointer properly.
Insert the plugfirmly
Turn on the tap
Press Power On/Off and
Start/Pause
If plug isinserted firmly?
If tap isturned on?
If Power On/Off and
Start/Pause is pressed?
Please contact the after-sales
service department.
Overflow alarm
The numeral tube shows
F2
Normal phenomena
Phenomena
Causes (explanations)
Adjust balance to avoid clothes offset
Intermittent spin after spin starts
The program sets a drain time, spin starts
after a time.
Spin is selected, yet the machine doesn't spin
While water filling in wash and rinse, the
pulsator pauses rotation
To prevent splash during water filling.
Small amount of water flows out upon the
washing machine is initially used
This is residual water during factory perfor
mance test.
This is a normal fact. Due to the drum rotation,
an open cover alarm function is provided for safety.
The machine stops when top cover is opened
during running.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Quantity
Name
1
1
1
1
2
User's manual
Warranty Card
Drain hose
Drain hose hook
Water inlet hose
Drain hose clamp
1
1
Automatic washing machine
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Model
Rated voltage frequency
Rated washing / spinning capacity 8.5kg (weight of standard dry cloth)
SIG100-97
220-240V~
50Hz
1/16L, 2/24L, 3/32L, 4/40L, 5/48L,6/56L, 7/60L, 8/72L, 9/80L, 10/90L
Water level/Water quantity (about)
Max water consumption
Injection pressure
About 180L(High water level; Normal program)
0.03MPa-1.0MPa
Rated washing power
Rated spinning power
Weight( bout)
525W
380W
75kg
Dimension
L 686 mm W 686 mm H 1080mm
Download from Www.Somanuals.com. All Manuals Search And Download.
|