Wireless Systems
UAPF-X1
UHF IN-LINE
PASSIVE
RF FILTER
©2008 Shure Incorporated
27A12024 (Rev. 2)
Printed in U.S.A.
*27A12024*
Download from Www.Somanuals.com. All Manuals Search And Download.
General Description
The Shure UAPF-X1 is an in-line passive RF filter to attenuate frequencies outside the
X1 band and intended to be used with any Shure X1 band wireless product that has
removable antennas, including SLX, ULX, and UHFR.
FeatUres
•
•
•
•
Filters out extraneous RF signals.
Mountable on supplied desk-/wall-mount or on a microphone stand
Extremely durable under the heaviest use
Shure quality, ruggedness, and reliability
application
Optimally, the unit should be located prior to any amplification of an RF signal.
Positioning should be tested and adjusted for each individual setup.
Antennas should be spaced far enough to obtain the widest possible RF field and to
minimize RF signal drop out. In a diversity system, Shure recommends that antennas
be positioned at 45°.
networking
antenna
B
in
antenna
A
in
receiver outputs
200Ω
network
activity
line
mic
lift
GND
12.7V
out
12.7V
out
ethernet
RJ-45
150mA
150mA
45
45
Figure 1. Diversity System
The following table shows three typical connectivity arrangements for the UAPF-X1:
Antenna
Passive
Filter
In line
Amplifier
Antenna
Distribution
Unit
Receiver
UA820X (or
PA805SWB,
UA860SWB,
PA805X)
UAPF-X1
UAPF-X1
UAPF-X1
UR4D-X1 (or
UA4S-X1)
UA820X (or
PA805SWB,
UA860SWB,
PA805X)
UA845-SWB
UA845-SWB
UR4D-X1 (or
UA4S-X1)
UA820X (or
PA805SWB,
UA860SWB,
PA805X)
UA830X
UR4D-X1 (or
UA4S-X1)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
installation
IMPORTANT: DO NOT USE INFORMATION:
This device must not be used with antennas or other devices that have a DC short
circuit at their feed point without using an external (BNC) DC Block. A suitable BNC
DC Block is the JFW Industries Model 50DB-002.
installation instrUctions
1. Thread the Shure Model UAPF-X1 unit on the supplied stand or on a 5/8 in.-27
thread microphone stand (Figure 2) and connect the antenna wand to either antenna
port (filter functions in both directions).
To Antenna
Figure 2. Attaching Base and Antenna
2. Using 50 W low-loss coaxial cable (purchased separately, Shure UA825 or UA850
or UA8100 recommended), connect to the opposite port to the Shure Model UR4
or ULX, SLX wireless receiver or UA845SWB, or UA844SWB Antenna Distribution
System (Figure 3).
To Receiver
Antenna In
UR4 WiReleSS ReCeiveR
Figure 3: Connecting Receiver
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MaintaininG cable inteGrity
To maintain Shure cables in top condition in permanent installations:
1. Avoid sharp bends or kinks in the cables.
2. Do not deform cables with makeshift clamps, such as bending a nail over the cable.
3. Do not use cables in permanent outdoor installations.
4. Do not expose cables to extreme moisture
Figure 4: Cable Chaining
speciFications
RF frequency range..............................................................3dB bandwidth = 36Mhz
.............................20dB bandwidth = 49Mhz
Stop-Band Attenuation: ..........................................Minimum 30dB, Typical 32-36dB
Insertion Loss....................................................................................Typical 3.25dB
Case..................................................................Aluminum die-casting, black painted
vSWR in pass-band (input, output):.......................................................Typical 2.0dB
Swivel Adapter ............................................................Positive action, break-resistant
adjustable from 0 degrees to 90 degrees,
with standard 5/8 in. –27 thread
Net Weight.......................................................Without mounting stand.28kg (9.8 oz)
.......................................................................With mounting stand .42 kg (14.8 oz)
Power Consumption (12 vdc)................. Passively passes power (12vdc) 0.6 to 0.72 W
for use with UA870X active antenna.
Connectors....................................................................................Female, BNC-type
Dimensions (without accessories)...............66.7 mm high x 31.75 mm wide x 112 mm
deep (2.625 x 1.250 x4.40 inches), 108 mm
(4.25 in.) high w/mounting stand
replaceMent parts
Mounting Base ..........................................................................................A13HDB
For additional service or parts information, please contact Shure’s Service department
at 1-800-516-2525. Outside the United States, please contact your authorized Shure
Service Center.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000
U.S. Fax: 847-600-1212
Intl Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140
Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290
Fax: 852-2893-4055
Download from Www.Somanuals.com. All Manuals Search And Download.
|