Controls and indicators
Controls and indicators
System connections (continued)
Remote control
ENGLISH
1
Operation with batteries
Remote control
MODEL
Battery installation
Front panel
17
18
1. Remote Control Transmitter
2. Demo/Dimmer Button
3. Numeric Buttons
4. Equalizer (X-Bass) Button
5. Tuner Preset Up Button
6. Tuner Preset Down Button
7. Folder Button
Fully charge the iPod, iPhone and iPad with AC power
before using GX-M10 battery operation.
1. Equalizer/X-Bass Button
2. Power On/Stand-by Button
3. Demo/Dimmer/Stop Button
4. Tuner/Audio In Button
5. Tuner Preset Down, CD/USB Track Down, iPod/
iPhone Skip Down Button
6. USB Play/Pause Button
7. Tuner Preset Up, CD/USB Track Up, iPod/iPhone
Skip Up Button
8. CD Play/Pause Button
9. Volume Down Button
10. iPod Play/Pause Button
11. Volume Up Button
12. Docking station door open knob
13. Timer indicator
14. Remote sensor
15. Docking station
16. USB/iPad Terminal
17. CD compartment
18. CD compartment open knob
Use 1 “AA” size battery (UM/SUM-3, R6, HP-7 or similar).
Battery is not included.
2
3
16
GX-M10
1 Disconnect the AC and DC power cord, and remove the
battery compartment cover.
z Remove USB connection and undock the iPod or iPhone
before installing batteries to avoid possible damage.
z Connection of the AC or DC power cord to the unit
disconnects the batteries.
1 Open the battery cover.
2 Insert the battery according to the terminal indicated in
the battery compartment.
When inserting or removing the battery, push it toward
the (–) battery terminals.
8. Tuning Up, iPod Cursor Up, Folder Up Button
9. Skip Down, Fast Reverse, Time Down Button
10. Tuning Down, iPod Cursor Down,
Folder Down Button
PORTABLE CD STEREO SYSTEM
3 Close the cover.
17
18
2 4 6 8 10
4
5
1 3 5 7 9 11
11. Memory Button
12. Audio In Button
OPERATION MANUAL
6
19
20
21
13. USB Play/Pause Button
14. Tuner Button
POWER
ON/STAND-BY
TUNER/AUDIO-IN
USB
CD
iPod
2 Insert 10 “D” size batteries (UM/SUM-1, R20, HP-2 or
similar) into the battery compartment according to the
sequence indicated on the rear panel.
X-BASS/EQ
DEMO/DIMMER
7
8
9
10
11
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual
carefully. It will guide you in operating your SHARP product.
PRESET
VOLUME
15. Display Button
Caution:
16. On/Stand-by Button
z Remove the battery if the unit will not be used for a long period
of time. This will prevent potential damage due to battery
leakage.
z Do not use rechargeable battery (nickel-cadmium battery,
etc.).
z Installing the battery incorrectly may cause the unit to
malfunction.
z Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, re or the like.
22
z When inserting or removing the batteries 5 and 0, push
17. Mute Button
12
them toward the (-) battery terminals.
18. Volume Up Button
23
24
25
19. Volume Down Button
20. Sleep (Clear) Button
z Installing the batteries incorrectly may cause the unit to
malfunction.
z Batteries are not included.
PORTABLE MUSIC BOOMBOX GX-M10
TIMER
21. Play Mode/Random Button
22. Skip Up, Fast Forward, Time Up Button
23. Enter Button
16
15
13
14
12
13
14
15
REMOTE
SENSOR
26
27
28
29
24. Clock (Timer) Button
25. CD Play/Pause Button
26. iPod Play/Pause Button
27. iPod Display (TV OUT) Button
28. CD/USB Stop Button
29. iPod Menu Button
Bottom row
Notes concerning use:
3
z Replace the battery if the operating distance is reduced or
if the operation becomes erratic. Purchase an “AA” size
battery (UM/SUM-3, R6, HP-7 or similar).
z Periodically clean the transmitter on the remote control and
the sensor on the unit with a soft cloth.
z Exposing the sensor on the unit to strong light may interfere
with operation. Change the lighting or the direction of the
unit if this occurs.
z Keep the remote control away from moisture, heat, shock,
and vibrations.
Top
5
4
1
2
3 4 5 6 7 8
9
2
row
Rear panel
1
Insert the batteries
according to the
8
1. FM antenna
9
2. DC 12 V input jack
3. Headphone jack
4. Microphone volume knob
5. Microphone input jack
6. Guitar input jack
7. Guitar volume knob
8. Audio input jack
9. Video output jack
10. AC input jack
10
System connections
sequence indicated.
7
6
3 Replace the battery compartment cover.
Precautions for battery use:
z Insert the batteries according to the direction indicated on the
rear panel.
z Remove the batteries if they are weak or if the unit will not be
used for long periods of time. This will prevent potential damage
due to battery leakage.
z Replace all old batteries with new ones at the same time.
z Do not mix old and new batteries.
Do not connect the DC and AC
power to the unit at the same time.
iPhone not included.
11
Carrying the unit
Caution:
Before transporting the unit, remove the iPod, iPhone,
iPad, USB memory device and disc from the unit. Then,
set the unit to the power stand-by mode. Transporting the
unit with iPod, iPhone, iPad or USB memory device left
connected or discs left inside might damage the unit.
iPad, iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
11. Cable holder
The safety marking and
statement label (*)
To AC INPUT
jack
10
AC outlet
AC 120 V ~ 60 Hz
Battery replacement:
1
2
9
3
4
5
6
7
Display
z When batteries are low, battery indicator “ ” will blink to show
that the batteries need to be replaced. sound may become
distorted and unit may automatically turn off or mute during
high volume level. Reduce the volume level or replace the
batteries.
z When replacing the batteries, place the unit on a cushion or soft
cloth to avoid damage.
CAUTION:
1. CD Indicator
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
2. USB Indicator
Using the carrying strap
(*) Label is located at the
bottom of the unit.
3. MP3 Indicator
8
21
22
10 11
12
13 14 15 16 17 18 19 20
This unit can be carried by using a supplied carrying strap. Insert the
carrying strap carabiner (hook) to each end of the unit as shown below.
4. WMA Indicator
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect
specically to iPod, iPhone, or iPad respectively, and has been certied by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
5. iPod Indicator
AC power connection
DC power connection
6. FM Stereo Mode Indicator
7. Stereo Station Indicator
8. Total Indicator
Carabiner (hook)
Cautions:
After checking all the connections have been made correctly,
plug the AC power cord of this unit into the AC outlet.
Caution:
z Do not use rechargeable battery (nickel-cadmium battery,
etc.).
z Immediately remove the discharged batteries. If the chemical
leak into the unit, clean it.
z Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, re or the like.
z During battery/DC operation, the unit will be set to Demo mode
off with display and subwoofer light in MODE 2 to reduce the
battery power consumption.
z When using battery/DC power, the remote control cannot be
used to turn on the unit.
z Unplug the AC power cord from the unit before using the DC
power. Otherwise the unit will not work.
z When the unit is not in use for an extended period, remove the
DC cord from the DC IN 12 V jack.
9. Folder Indicator
10. Title Indicator
11. MEM (Memory) Indicator
12. X-bass Indicator
13. Sleep Indicator
14. Once Timer Indicator
15. Daily Timer Indicator
16. RDM (Random) Indicator
17. Repeat Indicator
18. Microphone Indicator
19. Guitar Indicator
Notes:
z Remove all batteries when using AC power.
z Unplug the AC power cord from the AC outlet if the unit will not
be in use for a prolonged period of time.
Accessories
Hole
The following accessories are included.
To remove the
carrying strap
Demonstration mode
Connecting iPod or iPhone to TV
z The rst time the unit is plugged in with AC power, the unit will
enter the demonstration mode. You will see words scroll and
the subwoofer light up will operate in the ashing mode.
z To cancel the demonstration mode, press the DEMO/DIMMER
button (remote control) during power stand-by mode. The unit
will enter the low power consumption mode. The subwoofer
light will be off.
Speakers
Photo and video les from iPod or iPhone can be viewed by
connecting the system to TV/monitor.
If the TV/monitor has a video input, connect it to the VIDEO OUT
jack at the back of the unit and set the TV Out on the iPod or
iPhone unit to “ON” position.
Hole
R
T
A
B
L
E
M
U
S
I
C
B
O
O
M
B
O
X
GX-M10
P
O
20. Battery Level Indicator
21. Play Indicator
22. Pause Indicator
Cautions:
z Before carrying the unit, make sure the carabiner (hook) is
properly secured and closed, otherwise it will cause damage
and injury.
z Carry this unit with FM antenna close to you and the display
facing outward to avoid scratches on the display.
AC power cord x 1
(QACCD0025AWZZ)
Remote control x 1
(RRMCGA293AWSA)
Stand for iPad x 1
(GITAUA014AW01)
Dock spacer x 1
(PSPAGA003AWZZ)
Carrying Strap x 1
(JHNDZA001AW01)
Note:
Please make sure to set iPod unit to either NTSC or PAL to
match your TV signal. Please visit Apple’s homepage for further
information.
z To return to the demonstration mode, press the DEMO/
DIMMER button again.
1
2
3
z If iPod or iPhone is docked, the unit will begin charging. “iPod
CHARGING” will be displayed.
1. Front speaker
2. Subwoofer
3. Bass Reflex Duct
E-1
E-2
E-3
TINSZB414AWZZ
12H R KI 1
Volume auto fade-in
Placing the unit
Listening to the iPod, iPhone or iPad
Listening to the iPod, iPhone or iPad (continued)
Listening to a CD or MP3/WMA disc
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
This unit can be placed in 2 positions as shown below.
Caution:
z Make sure that the unit is placed on a at and level surface.
z Make sure to turn the unit carefully when adjusting the position.
z Do not place the unit other than these 2 positions to avoid damage
and injury.
To get the best display viewing angle, place the unit as below.
Position 1:
On the shelf/table.
Note:
POWER
ON/STAND-BY
Made for:
CD
iPod or iPhone playback (Dock only)
When navigating the iPod, iPhone or iPad menu with remote
z iPod touch (4th generation) z iPod nano (2nd generation)
z iPod touch (3rd generation) z iPhone 4S
z iPod touch (2nd generation) z iPhone 4
z iPod touch (1st generation) z iPhone 3GS
z iPod classic
z iPod nano (6th generation)
z iPod nano (5th generation)
z iPod nano (4th generation)
z iPod nano (3rd generation) z iPad
Caution:
control, do not operate any of the buttons on the iPod or iPhone
unit. The volume level is adjusted by pressing the VOL (+ or –)
button on the main unit or the remote control. Adjusting the volume
on the iPod, iPhone or iPad units give no effect.
1 Press the POWER ON/STAND-BY button to turn the
Volume control
power on.
Press VOLUME +/– buttons (on main unit) or VOL +/– (on remote
control) to increase or decrease the volume.
2 Press the iPod
/
button on the remote control or the
main unit to select iPod function.
Note:
z iPhone 3G
z iPhone
z iPad (3rd generation)
z iPad 2
3 Insert iPod or iPhone unit into the dock of main unit.
“DOCK OK” will appear. Make sure to close the docking
station door before playback.
PORTABLE MUSIC BOOMBOX GX-M10
iPod, iPhone and iPad operations:
The operations described below depend on the generation iPod,
iPhone and iPad you are using.
USB/iPad terminal does not support VIDEO out.
TIMER
Direct key power on function
REMOTE
SENSOR
iPod, iPhone or iPad playback (USB only)
When you press any of the following buttons, the unit turns on.
4 Press the iPod
/
button to start playback.
z iPod / , CD / , USB
/
on the main unit or the remote
System on operation:
When the main unit is powered on, the iPod, iPhone or iPad units
will automatically power on when docked or connected in the unit.
1 Press the POWER ON/STAND-BY button to turn the power on.
control: selected function is activated.
z TUNER/AUDIO IN on the main unit: last tuner or audio function
is activated.
Notes:
2 Press the USB
/
button on the remote control or the main unit
z When enjoying loud music at high volume, sound vibration is
transferred to the docked iPod or iPhone. This vibration may
cause the song to shufe if the iPod or iPhone ‘Shake to Shufe’
setting is turned on. Should this happen, turn off the ‘Shake to
Shufe’ function.
P
O
R
T
A
B
L
E
M
U
S
I
C
B
O
O
M
B
O
X
G
X
-
M
1
0
to select USB function.
Connect iPod, iPhone or iPad to the unit. “USB/iPod” will appear.
Please update your iPod, iPhone and iPad unit to the latest
software version before using it. Please visit Apple’s homepage
to download the latest version for your iPod, iPhone and iPad.
Notes:
3
System off (stand-by operation):
z TUNER or AUDIO IN on the remote control: the unit turns on
with the selected function activated.
When the main unit is turned to stand-by mode, the docked
iPod, iPhone or connected iPad unit will automatically pause the
playback.
Disc playback
Foot cushion 1 and 2
Direct track search
touching the surface.
Auto power off function
z Charging terminal for iPod, iPhone and iPad:
z
iPod touch and iPhone need to be operated itself in the
following operations.
1 Press the POWER ON/STAND-BY button to turn the power on.
By using the Numeric buttons, the desired tracks on the current
disc can be played.
Use the Numeric buttons on the remote control to select the
desired track while playing the selected disc.
z The Numeric buttons allow you to select up to number 9.
z When selecting number 10 or higher, use the “10+” button.
Position 2:
On the floor/ground
Track number
button to start playback.
2 Press the CD
/
button on the remote control or the main unit to select
The main unit will enter the stand-by mode (when iPad, iPod,
iPhone, guitar or microphone is not connected) after 15 minutes
of inactivity during:
Condition
DOCK
USB/iPad
terminal
1. Returning to the home screen.
2. Selecting the application on the home screen.
3. Dragging the slider.
4 Press the USB
Note:
Stop button ( ) is invalid during iPod, iPhone or iPad playback.
/
CD function.
Various iPod, iPhone and iPad functions
3 Open the CD compartment by pushing the CD compartment open knob to
the area marked ‘ ’.
M
U
S
I
C
B
O
O
MB
O
X
G
X
-
M
1
P
O
R
T
A
B
L
USB function
YES
YES
iPod:
Not docked.
To operate the connected iPod or iPhone, turn this unit
to position 2 (refer “Placing the unit” on page 4).
Function
Main unit
Remote
control
Operation
(without iPod or
iPhone docking)
Audio In:
CD:
No detection of input signal.
In the stop mode or no disc.
In the stop mode or no media.
4 Place the disc on the spindle, label side up.
5 Close the CD compartment.
iPhone playback
A. For example, to choose 13
1 Press the “10+” button once.
2 Press the “1” button.
POWER
ON/STAND-BY
DOCK USB DOCK USB
USB:
Note:
Other function
(iPod / CD /
Tuner / Audio In)
YES
YES
NO
z
Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10 seconds.
6 Press the CD
/
button to start playback. After the last track is played, the
Foot cushion 2 and 3
iPod
iPod
USB
USB
Play
Press in the pause
mode.
iPod
USB
unit will stop automatically.
touching the surface.
However, if iPod or iPhone is docked, the unit will begin charging.
“iPod CHARGING” will be displayed.
3 Press the “3” button.
z Incoming calls will pause the playback.
Caution:
z Once the calls are answered, the conversation can only be
heard through the built-in iPhone speaker. Turn on the iPhone
speaker or undock the iPhone to start conversation.
B. For example, to choose 130
1 Press the “10+” button twice.
2 Press the “1” button.
3 Press the “3” button.
4 Press the “0” button.
Stand-by
NO
z Do not place two discs in the spindle.
Auto resume function
General control
z Do not play discs of special shapes (heart, octagon, etc). It may cause
malfunctions.
z If TV or radio interference occurs during CD operation, move the unit away
from the TV or radio.
z Due to the structure of the disc information, it takes longer to read an MP3/
WMA disc than a normal CD (approximately 20 to 90 seconds).
z Do not open the CD compartment during playback or you may be injured.
Pause
Press in the
playback mode.
iPod
USB
z Fully charge the iPod, iPhone and iPad with AC power
before using GX-M10 battery operation.
PORTABLE MUSIC BOOMBOX GX-M10
TIMER
REMOTE
SENSOR
POWER
The auto resume function will resume the last function and
playback, should there be a power failure or the AC power cord
becomes disconnected. However, CD/MP3 program and random
mode are not memorized.
ON/STAND-BY
z The message “This accessory is not made to work with
iPhone” or similar, may appear on the iPhone screen
when:
iPod and iPhone connection (Dock only)
Notes:
Track
up/
down
Press in the
playback or pause
mode.
z A track number higher than the number of tracks on the disc
cannot be selected.
Caution:
- battery is low.
Unplug all accessories from the iPod or iPhone before inserting
it into the dock.
Equalizer
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
z This product is made for iPod, iPhone and iPad. To
prevent random interference when iPod, iPhone
or iPad is connected, the headphone output is
disabled, and “HPINVALD” will be displayed.
You may also experience brief audio interference
during incoming calls.
z During random play, direct search is not possible.
If you press the
button in the pause
mode, press the
Notes for CD or MP3/WMA disc:
PORTABLE MUSIC BOOMBOX GX-M10
TIMER
When the EQ/(X-BASS) button is pressed, the current mode
setting will be displayed. To change to a different mode, press
the EQ/(X-BASS) button repeatedly until the desired sound mode
appears.
Note:
To stop playback:
Press the DEMO/(DIMMER)/
z When the end of the last track is reached during fast forward, “END”
will appear on the display and CD operation will be paused. When the
beginning of the rst track is reached during fast reverse, the unit will enter
the playback mode (only for CD).
REMOTE
SENSOR
Do not use the docking station to connect your iPad.
(
) button.
/
button to start the
1 Open the docking station door by pushing
the docking station door open knob to the
area marked ‘ ’.
To disconnect iPod, iPhone or iPad
desired track.
Repeat play
FLAT
No equalization.
Fast
forward/
reverse
Press and hold
down in the playback
mode.
Release the button
to resume playback.
z Rewritable multi-session discs with unnished writing, can still be played.
It is safe to disconnect iPod, iPhone and iPad even during
playback. However, attention should be drawn when removing the
iPod or iPhone from docking station to avoid damage.
Repeat play can play one track, all tracks or a programmed
sequence continuously.
Cautions:
z Close the docking station door if
not in use.
z Do not press the docking station
door downward when it is open as
it may cause damage and injury.
Docking station
ROCK
VOCAL
For rock music.
Various disc functions
z The headphone output is switched off during inserting
iPod, iPhone and iPad unit. This is an Apple product
specication.
To repeat one track:
Vocals are enhanced.
Watching videos on a TV connected to
Press the PLAY MODE button repeatedly until “REP ONE”
Function
Play
Main unit
Remote
control
Operation
iPod or iPhone
appears. Press the CD
/
button.
HIP HOP For hip hop music.
SALSA For salsa music.
To turn the power on
Display
____
Press to toggle
display content.
iPod, iPhone and iPad connection (USB
1 Press the DISPLAY (TV OUT) button for more than 2 seconds
until “V-OUT ON” appear on display.
2 Press the ENTER button to start playback.
To repeat all tracks:
Press in the stop
mode.
Press the POWER ON/STAND-BY button to turn the power on.
only)
Press the PLAY MODE button repeatedly until “REPALL” appears.
Press the CD
/
button.
After use:
REGGAE For reggae music.
door
2 Dock your iPod or iPhone into the unit.
Repeat
Shuffle
Menu
____
____
____
____
Press to toggle
repeat mode.
1 Insert the connector to the iPod, iPhone or iPad.
Press the POWER ON/STAND-BY button to enter the power
stand-by mode.
Notes:
Stop
DEMO/(DIMMER)
Press in the
playback mode.
To repeat desired tracks:
iPhone
Muting
iPhone (bottom)
z If the TV Out setting is already turned on at video menu, the
video is automatically displayed on the TV screen when ENTER
key is pressed.
Perform steps 1 - 5 in “Programmed play” section on page 8 and
then press the PLAY MODE button repeatedly until “REP ALL”
appears.
iPad
Press for more than
2 seconds to toggle
shufe mode.
The volume is muted temporarily when pressing the
the remote control. Press again to restore the volume.
button on
Display and Subwoofer light up control
Pause
Press in the
z USB/iPad terminal does not support VIDEO OUT.
z To return to watching video on iPod or iPhone screen, press the
MENU button to enter video menu. Then press the DISPLAY
(TV OUT) button for more than 2 seconds until “V-OUT OFF”
appears.
z During iPod or iPhone video playback, pressing the DISPLAY
(TV OUT) button will not toggle video out display between iPod
and TV.
playback mode.
The display and subwoofer light can be changed.
Main unit:
Dock connector
Dock for iPhone
To cancel repeat play:
Press the PLAY MODE button repeatedly until “NORMAL” appears
and “ ” disappears.
Press the
/
button
X-Bass control
Press to view the
iPod menu during
iPod function.
Connector
to resume playback
from the paused
point.
1) Press DEMO/(DIMMER)/ button for more than 3 seconds.
The current mode will be displayed.
2) Within 5 seconds, press DEMO/(DIMMER)/ button to change
the mode.
When the power is rst turned on, the unit will enter the extra bass
mode which emphasizes the bass frequencies, and “X-BASS” will
appear. To cancel the extra bass mode, press the EQ/(X-BASS)
button. The last equalizer mode will turn on.
To turn on the X-Bass mode again, press the EQ/(X-BASS) button
for more than 2 seconds.
Caution:
Enter
Press to conrm the
selection.
Afterperformingrepeatplay,besuretopresstheDEMO/(DIMMER)/
Track
up/
down
Press in the
playback or stop
mode.
If you press the
button in the stop
mode, press the
2 Place the iPad to the stand for iPad.
For additional support, apply dock spacer (supplied) as shown.
(
) button. Otherwise, the disc will play continuously.
Remote control:
Press DEMO/DIMMER button to change the mode.
iPad
Caution:
Cursor
Up/
Down
____
Press to select the
iPod menu.
(Display backlight on and Subwoofer light off)
(Display backlight off and Subwoofer light off)
(Display backlight on and Subwoofer light on)
MODE 1
MODE 2
MODE Off
Peel off
separator
Stop button ( ) is invalid during iPod function
Navigating the iPod, iPhone or iPad menus
/
button to start the
desired track.
1 Press the MENU button to view the menu on iPod,
iPhone or iPad unit. Press it again to go back to
previous menu.
Notes:
Stand for iPad
Dock spacer
Docking station
Fast
forward/
reverse
Press and hold
down in the playback
mode.
Release the button
to resume playback.
z During battery/DC operation, the unit will be set to Demo mode
off with display and subwoofer light in MODE 2 to reduce the
battery power consumption.
2 Use the TUNING ( or ) button to select an item on
1 Peel off the double sided tape separator.
2 Place the spacer on the space allocated inside the docking
station as shown.
3 Connect the iPod, iPhone or iPad to the unit via USB
connector.
the menu and then press ENTER button.
z During MODE 2, press any button to light up the display
backlight for a few seconds.
E-4
E-5
E-6
E-7
Listening to USB mass storage device/MP3 player
Listening to the radio
Connecting other equipment
Advanced CD or MP3/WMA disc playback
MP3/WMA folder mode (only for
MP3/WMA files)
POWER
ON/STAND-BY
Caution:
The connection cord is not included. Purchase a commercially
available cord as shown below.
To remove USB memory device
Listening to the playback sounds of
Memorizing a station
At USB mode, once the iPod or iPhone is docked onto the unit,
the iPod or iPhone will automatically start charging. ‘iPod DOCK
CHARGE MODE’ will be displayed. In order to listen to any USB
mass storage device / MP3 player, the iPod or iPhone must be
removed from the docking station.
Random play
portable audio player, etc.
1 Press the DEMO/(DIMMER)/
2 Disconnect USB memory device from the USB/iPad terminal.
Notes:
z SHARP will not be held liable for the loss of data while the USB
memory device is connected to the audio system.
z Files compressed in MP3 and/or WMA format can be played back
when connected to the USB/iPad terminal.
(
) button to stop playback.
You can store 40 FM stations in memory and recall them at the
push of a button. (Preset tuning)
The tracks on the disc can be played in random order
automatically.
Connecting a guitar / microphone
1 Perform steps 1 - 3 in “Tuning”.
2 Press the MEMORY button.
3 Within 30 seconds, press the PRESET ( or ) button to select
the preset channel number. Store the stations in memory, in
order, starting with preset channel 1.
4 Within 30 seconds, press the MEMORY button to store that
station in memory. If the “MEM” indicator and preset number
disappear before the station is memorized, repeat the operation
from step 2.
5 Repeat steps 1 - 4 to set other stations, or to change a preset
station. When a new station is stored in the memory, the station
previously memorized for that preset channel number will be
erased.
To random play all tracks:
Caution:
Press and hold PLAY MODE button on the remote control until
Be careful not to connect a bass guitar as it might damage this
unit.
“RANDOM” appears. Press the CD
/
button.
PORTABLE MUSIC BOOMBOX GX-M10
TIMER
REMOTE
SENSOR
PORTABLE MUSIC BOOMBOX GX-M10
To cancel random play:
Press the PLAY MODE button again. “RDM” indicator will
disappear.
TIMER
REMOTE
SENSOR
z This USB memory’s format supports FAT 16 or FAT 32.
z SHARP cannot guarantee that all USB memory devices will work
on this audio system.
z USB cable is not recommended for use in this audio system to
connect to USB memory device. Use of the USB cable will affect
the performance of this audio system. iPod, iPhone and iPad is not
prone to this condition.
z This USB memory cannot be operated via USB hub.
z The USB/iPad terminal in this unit is not intended for a PC connection
but is used for music streaming with a USB memory device.
z External HDD-storage cannot be played back via USB/iPad
terminal.
z If the data inside the USB memory is large, it may take longer time
for the data to be read.
Notes:
z If you press the
button during random play, you can
move to the track selected next by the random operation. On
the other hand, the
button does not allow you to move
to the previous track. The beginning of the track being played
will be located.
Microphone or guitar
(not supplied)
Procedure to playback MP3/WMA disc
z In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Headphone (not
with folder mode on
Note:
supplied)
The backup function protects the memorized stations for a few
days should there be a power failure or theAC power cord become
disconnected.
Portable audio
To play back CD-R/RW.
player, etc.
Programmed play (CD)
1 Press the CD / button, and load an MP3/WMA disc. Press the
FOLDER button and disc info will be displayed.
2 Press the TUNING ( or ) button to select desired playback
folder. (Folder mode on)
Ø 1/4” (6.3 mm)
monaural cable
(not supplied)
You can choose up to 32 selections for playback in the order you
like.
To recall a memorized station
z This product can play WMAand MP3 les. It will automatically detect
the le type being played. If unplayable le is played on this product,
“NOTSUPRT” is indicated and the le will be automatically skipped.
This will take a few seconds. If abnormal indications appear on the
display due to the unspecied le, turn off the unit and then turn it
on again.
z This product relates to USB mass storage devices and MP3 players.
It may however face some irregularities due to various unforeseen
reasons from some devices. Should this happen, turn off the unit
and then turn it on again.
Audio cable (not supplied)
1 Press the PRESET ( or ) button for less than 0.5 seconds to
select the desired station.
1 While in the stop mode, press the MEMORY button on the
3 Select desired le to be played back by pressing the
or
remote control to enter the programming save mode.
1 Set the guitar/microphone volume (GAIN) knob to the minimum
level.
button.
1 Use a connection cord to connect the portable audio player etc.
to the AUDIO IN jack. When using video equipment, connect the
audio output to this unit and the video output to a television.
2 Press the POWER ON/STAND-BY button to turn the power on.
3 Press the AUDIO IN button on the remote control or TUNER/
AUDIO IN button repeatedly on the main unit to select AUDIO
IN function.
4 Play the connected equipment. If volume level of the connected
device is too high, sound distortion may occur. Should this
happen, lower the volume of the connected device. If volume
level is too low, increase the volume of the connected device.
2 Press the numeric button or
or
buttons on the
4 Press the CD
/
button. Playback will start and le name will
To scan the preset stations
remote control to select the desired track.
2 Connect a guitar/microphone to the correct input jack. Make sure
that the cable has a 1/4” (6.3 mm) diameter plug.
3 Arrange the guitar/microphone cables into the grooves of the
cable holder on the left or the right side of the unit.
Then, thread the cable through the bottom of the unit.
Do not let the cables to be on top of the unit when using
guitar/microphone as it may cause the unit to roll over
causing damage and injury.
be displayed.
3 Press the MEMORY button to save the track number.
4 Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks,
press the MEMORY button repeatedly. If you make a mistake,
the programmed tracks can be cleared by pressing the CLEAR
button for more than 2 seconds.
Tuning
z Title,Artist andAlbum name are displayed if they are recorded
on the disc.
Note:
The stations saved in the memory can be scanned automatically.
(Preset memory scan)
This product is not compatible with MTP and AAC le systems
from USB mass storage device or MP3 player.
1 Press the POWER ON/STAND-BY button to turn the
power on.
z In case of playback with the folder mode on, press the
TUNING ( or ) button, and the folder can be selected even
though it is in playback/pause mode. It will continue playback/
pause mode in the 1st track of the selected folder.
z Display content can be changed by pressing the DISPLAY
button.
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will ash and the programmed stations will
be tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired
station is located.
2 Press the TUNER button on the remote control or TUNER/
AUDIO IN button on the main unit repeatedly to select FM
Stereo or FM Mono.
To play back USB/MP3 player with folder
mode off
z During CD function, MP3 player will not be charging.
5 Press the CD
/
button to start playback.
3 Press the TUNING ( or ) button on the remote control
to tune in to the desired station.
1 Press the USB
/
button on the remote control or the main unit
Programmed play (MP3/WMA)
Advanced USB playback
to select USB function. Connect the USB memory device that
has MP3/WMA format les on the unit. When the USB memory
is connected to the main unit, the device information will be
displayed.
File name display
Folder display
To erase entire preset memory
z Manual tuning:
Note:
1 While in the stop mode, press the MEMORY button to enter the
programming save mode.
2 Press the TUNING ( or ) button on the remote control to
select the desired folder.
The following functions are the same as CD operations:
Page
Direct track search...................................................................... 7
Repeat play.................................................................................. 7
Random play................................................................................ 8
Programmed play (MP3/WMA) .................................................. 8
Press the TUNING ( or ) button repeatedly to tune in
to the desired station.
1 Press the POWER ON/STAND-BY button to enter the stand-by
To prevent noise interference, place the unit away from the
television.
mode.
Counter display
Title display
z Auto tuning:
2 Select desired le to be played back by pressing the
or
2 While pressing down the PRESET
button, press the POWER
When the TUNING ( or ) button is pressed for more
than 0.5 seconds, scanning will start automatically
and the tuner will stop at the rst receivable broadcast
station.
button.
Album display
Artist display
ON/STAND-BY button until “TUNCLEAR” appears.
Then press the
or
button on the remote control to
Headphones
3 Press the USB
/
button. Playback will start and the le name
Note:
select the desired tracks.
Thread the cables under the unit
Cable holder
POWER
ON/STAND-BY
will be displayed.
z Do not turn the volume on to full at switch on and listen to music
at moderate levels. Excessive sound pressure from earphones
and headphones can cause hearing loss.
z Before plugging in or unplugging the headphone, reduce the
volume.
z Be sure your headphone has a 1/8” (3.5 mm) diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
z Plugging in the headphone disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
3 Press the MEMORY button to save the folder and track
If “NOTSUPRT” is displayed, it means “Copyright protected WMA
le” or “Not supported playback le” is selected.
z Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
number.
Note:
Notes:
4 Repeat steps 2 – 3 for other folder/tracks. Up to 32 tracks can
z Display content can be changed by pressing the DISPLAY
button.
If USB memory device is not connected, “NO MEDIA” will be
shown on the display.
z When radio interference occurs, auto scan tuning may
stop automatically at that point.
z Auto scan tuning will skip weak signal stations.
z To stop the auto tuning, press the TUNING ( or ) button
again.
be programmed.
5 Press the CD
/
button to start playback.
Note:
To pause playback:
Press the USB button.
Notes:
To cancel the programmed play mode:
z This unit only supports “MPEG-1 Audio Layer-3” format. (Sampling
Frequency is 32, 44.1, 48kHz)
During programmed stop mode, press the DEMO/(DIMMER)/
(
)
/
button. The display will show “MEM CLR” and all the programmed
contents will be cleared.
z Playback order for MP3 les may differ depending on the writing
software used during le download.
To receive an FM stereo transmission:
4 Connect the cables to a guitar/microphone.
5 Select a source.
z To mix a guitar or microphone sound with a source sound,
select the playback source (iPod/CD/USB/Audio In/Tuner).
ꢀz To play a guitar or using the microphone only, select ’AUDIO
IN’ function. Make sure there is no playback from Audio In
connection.
6 Adjust the volume (GAIN) knob on the connected equipment.
ꢀz To enjoy a guitar distortion effect, turn the guitar volume
(GAIN) knob to almost maximum level.
To play back USB/MP3 player with folder
z Press the TUNER button to select stereo mode and “ST”
indicator will be displayed. “ ” will appear when an FM
broadcast is in stereo.
z If the FM reception is weak, press the TUNER button to
extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
mode on
Adding tracks to the program:
z Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160
kbps.
If a program has been previously stored, the “MEM” indicator will
be displayed. Press the MEMORY button. Then follow steps 2
- 3 to add tracks.
1 Press the USB
/
button on the remote control or the main unit
z For MP3/WMA les, please put “.MP3” “.WMA” extension. Files
cannot be played back if there is no MP3/WMA extension.
z Playlists are not supported on this unit.
to select USB function. Connect the USB memory device that
has MP3/WMA format les on the unit. When the USB memory
is connected to the main unit, the device information will be
displayed.
Notes:
z When a CD compartment door is opened, the program is
automatically canceled.
z This unit can display Folder Name or File Name up to 32
characters.
2 Press the FOLDER button, and press the TUNING ( or
)
z If you press the POWER ON/STAND-BY button to enter the
stand-by mode or change the function from CD to another, the
programmed selections will be cleared.
z Maximum total number of MP3/WMA les is 65025.
z Total number of folders read is 999 including folder with non-playable
le. However, the display shows only folder with MP3 les.
z The display playback time may not be displayed correctly when
playing back a variable bitrate le.
z The ID3TAG information supported are TITLE, ARTIST and ALBUM
only. Title name, artist name and album name can be displayed by
pressing the DISPLAY button during le playback or pause mode.
z WMA meta tag also supports title, artist and album name which
are recorded in WMA les. Copyright protected WMA les cannot
be played back.
button to select desired playback folder. To start playback with
folder mode on, go to step 4. To change the playback folder,
press the TUNING ( or ) button to select another folder.
Note:
z During the program operation, random play is not possible.
Before disconnecting the guitar/microphone, set the guitar/
microphone volume (GAIN) knob to the minimum level.
3 Select desired le to be played back by pressing the
or
button.
4 Press the USB
/
button. Playback will start and the le name
will be displayed.
z Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
z Display content can be changed by pressing the DISPLAY
button.
E-8
E-9
E-10
E-11
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program, and use
the daily timer to wake up.
Timer and sleep operation (Remote
control only) (continued)
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
Troubleshooting chart (continued)
Specifications
Setting the clock (Remote control only)
If such a problem occurs, do the following:
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specication changes for product
improvement without prior notice. The performance specication
gures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
USB
USB (MP3 / WMA)
1 Set the daily timer (pages 12 - 13).
2 Set the once timer (pages 12 - 13).
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit again, and then turn the power on.
Checking the timer setting:
1 Turn the power on and press and hold down the CLOCK/TIMER
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
Symptom
Possible cause
USB host interface
z Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage Class.
z Support Bulk only and CBI protocol.
button.
1 minute or more
2 Within 10 seconds, press the
“ONCE” or “DAILY”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
or
button to select
z Device cannot be
detected.
z There is no MP3/WMA le
inside the device.
z The device is not properly
connected.
Note:
General
Daily timer
Start
Once timer
Start Stop
If neither operation above restores the unit, clear all the memory
by resetting it.
General
Support file
Bitrate support
Other
z MPEG 1 Layer 3
Stop
“TIM.CALL”, and press the ENTER button.
z WMA (Non DRM)
Symptom
Possible cause
z A MTP device is connected.
z The device contains AAC le
only.
Factory reset, clearing all memory
Cancelling the timer setting:
1 Turn the power on and press and hold down the CLOCK/TIMER
Power source
AC 120 V ~ 60 Hz
z MP3 (32 ~ 320 kbps)
z WMA (64 ~ 160 kbps)
z The clock is not set to
the correct time.
z A power failure occured.
z Reset the clock. (Refer page
12)
Timer playback
15 V
(UM/SUM-1, R20) x 10
1 Press the POWER ON/STAND-BY button to enter the power
stand-by mode.
2 While pressing down the VOLUME + button, press the POWER
ON/STAND-BY button until “RESET” appears.
button.
DC IN 12 V
z Maximum total number of MP3/WMA
les is 65025.
z Playback does not start. z A copyright-protected WMA or
2 Within 10 seconds, press the
“ONCE” or “DAILY”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
or
button to select
Before setting timer:
Power
consumption
AC: Power on: 30 W
DC 12 V: 4.5 A
z When a button is
pressed, the unit does
not respond.
z Set the unit to the power
stand-by mode and then turn
it back on.
z If the unit still malfunctions,
reset it. (Refer page 14)
false MP3 le is being played
z Maximum total number of folders is
999 INCLUSIVE of root directory.
z The ID3TAG information supported
are TITLE, ARTIST and ALBUM only.
z Supports ID3TAG version 1 and
version 2.
z Check that the clock is set to the correct time (refer left
column). If it is not set, you cannot use the timer function.
back.
In this example, the clock is set for the 12-hour (AM 12:00) display.
POWER
ON/STAND-BY
Dimensions
Width: 30 - 5/16’’ (750 mm)
Height: 10 - 13/16” (275 mm)
Depth: 11 - 1/16” (280 mm)
“TIM.OFF”, and press the ENTER button. Timer will be canceled
(the setting will not be canceled).
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the CLOCK/TIMER button.
z Wrong time display.
z Wrong le name display.
z A Variable Bitrate les are being
played back.
z The File Name was written in
other than English characters.
z
For timer playback: Plug in USB or load discs or dock
iPod to be played.
3 Within 10 seconds, press the ENTER button.
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse
the same setting, perform the following operations.
4 Press the
or
button to select 12-hour or 24-hour
z No sound is heard.
z The volume level is set to
“MIN”.
z The headphones are
connected.
Weight
16.8 lbs. (7.6 kg)
display and then press the ENTER button.
(without
Caution:
File system
support
z
Support USB devices with
Microsoft Windows/DOS/FAT 16/
FAT 32.
batteries and
accessories)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
1
Press the POWER ON/STAND-BY button to turn the power
on.
This operation will erase all data stored in memory including clock,
timer settings and tuner preset.
iPod, iPhone or iPad
1 Turn the power on and press and hold down the CLOCK/TIMER
button.
z Sound too low or
distorted.
z Power suddenly shuts
down.
z The batteries are depleted.
Change the batteries.
2
3
Press and hold the CLOCK/TIMER button.
Weight
(with batteries)
Approximately 20.2 lbs (9.2 kg)
z
2 kbyte block length for sector.
2 Within 10 seconds, press the
or
button to select
Symptom
Possible cause
Care of compact discs
Within 10 seconds, press the
“ONCE” or “DAILY”, and press the ENTER button.
Within 10 seconds, press the or button to select
“TIM.SET”, and press the ENTER button.
To select the timer playback source (CD, TUNER, USB, iPod,
AUDIO IN), press the or button.
When you select the tuner, select a station by pressing the
or button, and then press the ENTER button.
or
button to select
“ONCE” or “DAILY”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
z No sound is produced.
No image appears on
the TV/monitor.
z The iPod, iPhone or iPad is not
playing.
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface.
Follow the guidelines below for maximum enjoyment from your
CD collection and player.
z Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
z Keep your discs away from direct sunlight, heat, and excessive
moisture.
z Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight
out from the center, along the radius.
Tuner
4
5
“TIM.ON” , and press the ENTER button.
Amplifier
z The iPod, iPhone or iPad is not
properly connected to the unit.
z The AC power cord of the unit
is not plugged in.
4 Press the POWER ON/STAND-BY button to enter the power
5
6
To adjust the hour, press the
or
button
stand-by mode.
Frequency range
Preset
FM: 87.5 - 108 MHz
40 (FM station)
CD player
and then press the ENTER button. Press the
or
Output power
Front speaker:
button once to advance the time by 1 hour. Hold
it down to advance continuously.
Sleep operation
RMS: Total 34 watt (17 W per channel
into 3 ohms at 1 kHz, 10% T.H.D.)
FTC: 12.5 watt minimum RMS per
channel into 3 ohms from 200 Hz to
20 kHz, 10% T.H.D.
Symptom
Possible cause
z The video cable is not properly
connected.
To adjust the minutes, press the
or
button
The radio, compact disc, iPod, USB, and Audio In function can all
be turned off automatically.
Speaker
If a station has not been programmed, “NOPRESET” will be
displayed and timer setting will be canceled.
Press the ENTER button to adjust the hour. Press the
z Playback does not start. z The disc is loaded upside
and then press the ENTER button. Press the
or
z The TV/monitor’s input
selection is not properly set.
z The iPod TV out feature has not
been set to output video.
z USB/iPad terminal does not
support video.
z Playback stops in
the middle or is not
performed properly.
down.
button once to advance the time by 1 minute.
Hold it down to advance the time by 5 minutes interval.
1 Play back the desired sound source.
2 Press the SLEEP button.
z The disc does not satisfy the
standards.
6
7
Type
2-way type speaker system
Front Speakers:
or
button and then press the ENTER button.
Subwoofer:
To confirm the time display:
Press the CLOCK/TIMER button. The time display will appear for
about 5 seconds.
3 Within 5 seconds, press the Numeric button to set the time. (1
minute ~ 99 minutes)
z The disc is distorted or
scratched.
RMS: Total 66 watt into 3 ohms
at 100 Hz, 10% T.H.D.
FTC: 50 watt minimum RMS into
3 ohms from 70 Hz to 200 Hz, 10%
T.H.D.
To adjust the minutes, press the
then press the ENTER button.
or
button and
3-1/8” (8 cm) - 3 - Full Range
Subwoofer: 5- 1/8” (13 cm) - 6
- Woofer (light-up)
4 “SLEEP” will appear.
NO
YES
Correct
8
9
Set the time to nish as in steps 6 and 7 above.
Adjust the volume using the VOLUME control, and then press
the ENTER button. Do not turn the volume up too high.
5 The unit will enter the power stand-by mode automatically after
the preset time has elapsed. The volume will be turned down 1
minute before the sleep operation nishes
z Playback sounds are
skipped, or stopped in
the middle of a track.
z The unit is located near
excessive vibrations.
Notes:
z iPod, iPhone or iPad will z The iPod, iPhone or iPad is
Maximum input
power
Front Speakers: 34W / Channel
Subwoofer: 66W / Channel
z When power supply is restored after unit is plugged in again
or after a power failure, conrm the clock, if required, reset the
clock from step 1 onward.
z The clock will continue counting for a few hours should there be
a power failure or the AC power cord becomes disconnected.
not charge.
not making full contact with the
connector.
z A very dirty disc has been used.
z Condensation has formed
inside the unit.
10 Press the POWER ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and the unit is
ready for timer playback.
Output terminals
Input terminals
Video output: 1 Vp-p
To confirm the remaining sleep time:
1 While “SLEEP” is indicated, press the SLEEP button.
z Using iPod (3rd generation).
z The iPod or iPhone is not
supported. Refer to page 5 for
compatible models.
Rated input power
Front Speakers: 17W / Channel
Subwoofer: 33W / Channel
Headphones: 16 - 50
z Volume level is too high. Adjust
to lower volume.
(recommended: 32 )
To cancel the sleep operation:
Audio In (audio signal):
To readjust the clock:
Press the POWER ON/STAND-BY button while “SLEEP” is
indicated. To cancel the sleep operation without setting the unit to
the stand-by mode, proceed as follows.
Maintenance
500 mV/47 k ohms
Perform “Setting the clock” from step 1. If the “CLOCK” does
not appear in step 2, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
z “This accessory is
not made to work
with iPhone” or “This
accessory is not
supported by iPhone”
appears on iPhone
screen.
z The iPhone battery is low.
Please charge the iPhone.
z iPhone is not properly docked.
TIMER
Mic Input: 200 - 2 k Ø 1/4” (6.3 mm)
Remote control
REMOTE
SENSOR
Guitar: 100 k - 1 M Ø 1/4” (6.3 mm)
Cleaning the cabinet
1 While “SLEEP” is indicated, press the SLEEP button.
2 Within 5 seconds, press the “0” button twice until “SLEEP 00”
appears.
To change the 12-hour or 24-hour display:
Symptom
Possible cause
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
1 Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2 Perform “Setting the clock” from step 1 onward.
CD player
Type
z The remote control does z The AC power cord of the unit
11 When the preset time is reached, playback will start. The
volume will increase gradually until it reaches the preset
volume. The timer indicator will blink during timer playback.
12 When the timer end time is reached, the system will enter the
power stand-by mode automatically.
Once timer:
The timer will be canceled.
not operate.
is not plugged in.
To use timer and sleep operation together
Caution:
z Wrong battery polarity.
z The batteries are exhausted.
z The distance or angle is
incorrect.
Single disc multi-play compact disc
player
z Do not use chemicals for cleaning (gasoline, paint thinner, etc.).
It may damage the cabinet.
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
1 Set the sleep time (see above, steps 1 - 5).
2 While the sleep timer is set, set the timer playback (steps 2 - 9,
page 12).
Timer and sleep operation (Remote
control only)
Condensation
z Do not apply oil to the inside of the unit. It may cause
malfunctions.
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
z The remote control sensor
receives strong light or sunlight.
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation inside
the cabinet (CD pickup, etc.) or on the transmitter on the remote
control. Condensation can cause the unit to malfunction. If this
happens, leave the power on with no disc in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Timer playback:
The unit turns on and plays the desired source (CD, TUNER, USB,
iPod, AUDIO IN) at a preset time.
D/A converter
Multi bit D/A converter
20 - 20,000 Hz
Daily timer:
Frequency
response
The timer operates at the same time every day. It will continue
until the daily timer setting is canceled. Cancel the daily timer
when it is not in use.
Tuner
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Timer playback
setting
Sleep timer
setting
Dynamic range
90 dB (1 kHz)
End time
Desired time
Timer playback start time
Symptom
Possible cause
Notes:
Once timer:
z The radio makes
unusual noises
continuously.
z The unit is placed near the TV
or computer.
z The FM antenna is not properly
extended or positioned.
z When performing timer playback using another unit connected
to the USB/iPad terminal or AUDIO IN jack, select “USB” or
“AUDIO IN” in step 5. However, if the source is set to USB,
make sure there is no iPod or iPhone docked to the unit.
z This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn on or off.
To stop the timer playback, follow step “Cancelling the timer
setting” on page 13.
Once timer play works for one time only at a preset time.
(“ ” indicator).
If problem occurs
1-99 minutes
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
Sleep operation will
automatically stop
Daily timer:
Daily timer play works at the same preset time every day. For
example, set the timer as a wake-up call every morning.
(“DAILY” indicator).
E-12
E-13
E-14
E-15
GX-M10H_OM_USA_EN_A1.indd
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2012-11-07 07:04:21
|