Sharp Projector XV Z30000 User Manual

PROJECTOR  
MODEL  
XV-Z30000  
OPERATION MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using the projector, please read this operation manual carefully.  
ENGLISH  
Introduction  
High brightness light source. Do not stare into the beam of light, or view  
directly. Be especially careful that children do not stare directly into the  
beam of light.  
WARNING:  
To reduce the risk of fire or electric shock, do not  
expose this product to rain or moisture.  
WARNING:  
See bottom of projector.  
The lightning flash with arrowhead sym-  
bol, within an equilateral triangle, is in-  
tended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product's enclosure that may  
be of sufficient magnitude to constitute  
a risk or electric shock to persons.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE SCREWS  
EXCEPT SPECIFIED USER  
SERVICE SCREW.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER.  
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
The exclamation point within a triangle  
is intended to alert the user to the pres-  
ence of important operating and main-  
tenance (servicing) instructions in the  
literature accompanying the product.  
WARNING:  
This is a Class A product. In a domestic environment this product may cause  
radio interference in which case the user may be required to take adequate  
measures.  
FCC Regulations state that any unauthorized changes or modifications  
to this equipment not expressly approved by the manufacturer could  
WARNING:  
void the user's authority to operate this equipment.  
U.S.A. ONLY  
PRODUCT DISPOSAL  
This product utilizes lamp containing a small amount of mercury.  
Disposal of these materials may be regulated due to environmental  
considerations. For disposal or recycling information, please contact  
1-800-BE-SHARP.  
U.S.A. ONLY  
This product contains a CR Coin Lithium Battery which contains Perchlorate Material –  
special handling may apply, California residents,  
U.S.A. ONLY  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the operation manual, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and the receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
U.S.A. ONLY  
Declaration of conformity  
SHARP PROJECTOR, MODEL XV-Z30000  
This device complies with Part 15 of the FCC rules. Operation is subject to the following  
conditions: (1) This device may not cause harmful interference, and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
Responsible Party:  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07495-1163  
TEL: 1-800-BE-SHARP (1-800-237-4277)  
Caution Concerning Lamp Replacement  
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp  
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface  
scratches or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition  
and the frequency of use. It is important to note that failure can often result in the bulb cracking.  
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that  
the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.  
Should the lamp break, there is also a possibility that glass particles may spread inside of the  
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector  
Dealer or Service Center to assure safe operation.  
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In  
case of exposure to the gas, consult a doctor as soon as possible.  
Caution  
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may  
cause burns or injury.  
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to  
fully cool before removing the lamp unit.  
• Do not touch the glass surface of the lamp unit or the inside of the projector.  
• Do not loosen other screws except for the lamp unit cover and lamp unit.  
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and  
continue to use the same lamp, this may cause the lamp to become damaged or explode.  
Carefully change the lamp by following the instructions described on pages 78 to 80.  
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector  
Dealer or Service Center.  
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized  
Projector Dealer or Service Center for repair.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Read this Operation Manual  
The specifications are slightly different, depending on the model. However, you can connect  
and operate all models in the same manner.  
In this operation manual, the illustration and the screen display are simplified for explanation, and  
may differ slightly from the actual display.  
Using the Menu Screen  
RETURN button  
• Press RETURN to return to the  
previous screen when the menu is  
displayed.  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
MENU button  
MENU button  
Adjustment buttons  
(P/R/O/Q)  
ENTER button  
Buttons used in  
this operation  
RETURN button  
• Press RETURN to return  
to the previous screen  
when the menu is  
displayed.  
Menu Selections (Adjustments)  
Button used in  
Example: Adjusting “Bright”.  
• This operation can also be performed by using the buttons on the projector.  
this step  
Press MENU.  
Example: “Picture” screen menu  
Menu item  
1
2
• The “Picture” menu screen for the selected  
input mode is displayed.  
Picture  
Picture Mode  
Contrast  
Bright  
SIG  
SCR  
PRJ  
Standard  
Net.  
Press Q or O and select  
“Picture” to adjust.  
0
0
0
0
0
0
0
0
0
On-screen  
display  
Color  
Tint  
Sharp  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
IRIS1 (Manual)  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Reset  
High Brightness  
On  
Off  
SEL./ADJ.  
RETURN  
ENTER  
END  
42  
.........Indicates safeguards for using the projector.  
Info  
Indicates additional information for setting up and operating the  
projector.  
.......  
Note  
For Future Reference  
Maintenance  
Troubleshooting  
Index  
P. 75  
PP. 83 to 85  
P. 89  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Preparing  
Introduction  
Useful Features  
How to Read this Operation Manual......3  
Contents.................................................4  
IMPORTANT SAFEGUARDS ..................6  
How to Access the PDF Operation  
Manuals..............................................11  
Accessories..........................................12  
Part Names and Functions...................13  
Side View ............................................... 13  
Top View ................................................ 13  
Front View.............................................. 13  
Rear View (Terminals).............................. 14  
Inserting the Batteries............................. 16  
Usable Range......................................... 17  
Operating with the Remote Control......37  
Adjusting the Image................................ 37  
Selecting the Picture Mode..................... 37  
Switching the Iris Setting ........................ 38  
Auto Sync (Auto Sync Adjustment) ......... 38  
Hiding the Menu Temporarily  
(Menu Hide) ......................................... 38  
Switching the Eco+Quiet Mode .............. 38  
Menu Items...........................................39  
Using the Menu Screen........................42  
Menu Selections (Adjustments) ............... 42  
Picture Adjustment (“Picture” Menu) ....44  
Selecting the Picture Mode..................... 44  
Adjusting the Image................................ 45  
Switching the Iris Setting ........................ 45  
Eco+Quiet.............................................. 45  
Using the Advanced ............................... 45  
Correcting Gradation of Video  
Easy Start  
Easy Start.............................................18  
Setup and Projection.............................. 18  
(Gamma Correction) ............................ 45  
Custom Gamma..................................... 46  
Adjusting the Colors ............................... 46  
Adjusting the Bright Boost...................... 48  
Selecting the Film Mode ......................... 48  
Setting Color Enhancement.................... 48  
Setting Detail Enhancement.................... 48  
Reducing Image Noise (DNR) ................. 48  
Mosquito Noise Reduction (MNR)........... 48  
Resetting All Adjustment Items ............... 48  
Computer Image Adjustment  
(“SIG-ADJ” Menu)..............................49  
Adjusting the Computer Image ............... 49  
Setting the Resolution ............................ 49  
Auto Sync (Auto Sync Adjustment) ......... 49  
Signal Type Setting................................. 50  
Setting the Video Setup.......................... 50  
Adjusting the Dynamic Range................. 50  
Signal Info .............................................. 50  
Adjusting the Projected Image  
Setup  
Setting Up the Projector.......................20  
Video Setup............................................ 20  
Setting Up the Projector ......................... 20  
Standard Setup (Front Projection)........... 20  
Screen Size and Projection Distance ...... 21  
Projection (PRJ) Mode............................ 22  
Ceiling-Mount Setup............................... 22  
Connections  
Connecting the Projector to  
Other Equipment................................23  
Connecting to Video Equipment ..........24  
Connecting to a Computer...................25  
Controlling the Projector by  
a Computer........................................26  
Connecting the Power Cord.................27  
(“SCR-ADJ” Menu).............................51  
Setting the Resize Mode......................... 51  
Adjusting the Image Position .................. 51  
Trigger.................................................... 51  
Anamorphic............................................ 51  
Adjusting the Overscan........................... 52  
Black Mask ............................................ 52  
CBNR..................................................... 52  
Setting On-screen Display ...................... 52  
Setting the Brightness of the Menu  
Screen................................................. 52  
Selecting the Background Image............ 52  
Selecting the Menu Screen Position ....... 53  
Reversing/Inverting Projected Images..... 53  
Selecting the On-screen Display  
Using  
Basic Operation  
Turning the Projector On/Off ................28  
Turning the Projector On......................... 28  
Turning the Power Off (Putting the  
Projector into Standby Mode) .............. 28  
Image Projection ..................................29  
Shifting the Lens..................................... 29  
Using the Adjustment Feet...................... 30  
Adjusting the Focus................................ 30  
Adjusting the Projected Image Size......... 30  
Correcting Trapezoidal Distortion............ 31  
Switching the Input Mode....................... 35  
Resize Mode .......................................... 36  
Language ............................................ 53  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting....................................83  
For SHARP Assistance.........................86  
Specifications.......................................87  
Dimensions...........................................88  
Index.....................................................89  
Adjusting the Projector Function  
(“PRJ-ADJ” Menu) .............................54  
Setting Auto Power Off Mode................. 54  
Setting No Operation Off Mode .............. 54  
Setting the Power Save Mode  
(Economy Mode) ................................. 54  
Setting One Touch Play, System  
Standby and Input Name..................... 55  
Turning LED Off ...................................... 56  
Setting the Demo Mode ......................... 56  
Fan Mode Setting................................... 56  
Memory Menu........................................ 56  
Returning to the Default Settings ............ 57  
Lamp Timer (Life).................................... 57  
Setting Up the Projector Network  
Environment (“Network” Menu)..........58  
Setting a Password ................................ 58  
DHCP Client Setting............................... 59  
TCP/IP Setting........................................ 59  
Returning to Default Settings (Network) .. 59  
Restart Network Function....................... 59  
Confirming the Projector Information....... 60  
Enjoying 3D Image Viewing..................61  
Precautions on using the 3D Glasses ..... 61  
Precautions on installing the IR emitter ... 61  
Precautions on viewing 3D images ......... 62  
Supplied Accessories for  
the 3D Glasses .................................... 64  
Part Names............................................ 64  
Before Using the 3D Glasses.................. 65  
Replacing the Button Cell Battery........... 65  
Attaching the Nose Pad.......................... 66  
Attaching the 3D Glasses Band.............. 66  
Using the 3D Glasses............................. 66  
Connecting the IR Emitter to  
the Projector........................................ 67  
Viewing 3D Images................................. 68  
3D Settings (“3D MENU”) ....................... 70  
Setting the 3D Format Menu................... 71  
Specifications – 3D Glasses ................... 73  
Specifications – IR Emitter...................... 74  
Dimensions ............................................ 74  
Effective Distance................................... 74  
Reference  
Appendix  
Maintenance.........................................75  
Maintenance Indicators........................76  
Regarding the Lamp.............................78  
Lamp...................................................... 78  
Caution Concerning the Lamp................ 78  
Replacing the Lamp ............................... 78  
Removing and Installing the  
Lamp Unit............................................ 79  
Resetting the Lamp Timer ...................... 80  
Compatibility Chart ..............................81  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
CAUTION: Please read all of these instructions before you operate this  
product and save these instructions for later use.  
Electrical energy can perform many useful functions. This product has been engineered  
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN  
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the  
safeguards incorporated in this product, observe the following basic rules for its  
installation, use and servicing.  
1. Read Instructions  
10. Ventilation  
Slots and openings in the cabinet are provided  
All the safety and operating instructions  
should be read before the product is  
operated.  
for ventilation to ensure reliable operation of  
the product and to protect it from overheating,  
and these openings must not be blocked or  
covered. The openings should never be  
blocked by placing the product on a bed, sofa,  
rug, or other similar surface. This product  
should not be placed in a built-in installation  
such as a bookcase or rack unless proper  
ventilation is provided or the manufacturer's  
instructions have been adhered to.  
2. Retain Instructions  
The safety and operating instructions  
should be retained for future reference.  
3. Heed Warnings  
All warnings on the product and in the  
operating instructions should be adhered to.  
4. Follow Instructions  
All operating and use instructions should  
be followed.  
11. Power Sources  
This product should be operated only from  
the type of power source indicated on the  
marking label. If you are not sure of the  
type of power supply to your home, consult  
your product dealer or local power  
company. For products intended to operate  
from battery power, or other sources, refer  
to the operating instructions.  
5. Cleaning  
Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
6. Attachments  
Do not use attachments not recommended by the  
product manufacturer as they may cause hazards.  
7. Water and Moisture  
Do not use this product near water–for  
example, near a bath tub, wash bowl, kitchen  
sink, or laundry tub; in a wet basement; or  
near a swimming pool; and the like.  
8. Accessories  
12. Grounding or Polarization  
This product is provided with one of the  
following types of plugs. If the plug should  
fail to fit into the power outlet, please contact  
your electrician.  
Do not defeat the safety purpose of the plug.  
a. Two-wire type (mains) plug.  
b. Three-wire grounding type (mains) plug  
with a grounding terminal.  
Do not place this product on an unstable  
cart, stand, tripod, bracket, or table. The  
product may fall, causing serious injury to a  
child or adult, and serious damage to the  
product. Use only with a cart, stand, tripod,  
bracket, or table recommended by the  
manufacturer, or sold with the product. Any  
mounting of the product should follow the  
manufacturer's instructions, and should use a  
mounting accessory recommended by the  
manufacturer.  
This plug will only fit into a grounding  
type power outlet.  
13. Power-Cord Protection  
Power-supply cords should be routed so  
that they are not likely to be walked on or  
pinched by items placed upon or against  
them, paying particular attention to cords  
at plugs, convenience receptacles, and the  
point where they exit from the product.  
9. Transportation  
14. Lightning  
A product and cart  
For added protection for this product during  
a lightning storm, or when it is left  
unattended and unused for long periods of  
time, unplug it from the wall outlet and  
disconnect the cable system. This will  
prevent damage to the product due to  
lightning and power-line surges.  
combination should be  
moved with care. Quick  
stops, excessive force, and  
uneven surfaces may  
cause the product and cart  
combination to overturn.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
e. If the product has been dropped or  
damaged in any way.  
f. When the product exhibits a distinct  
change in performance, this indicates a  
need for service.  
15. Overloading  
Do not overload wall outlets, extension cords,  
or integral convenience receptacles as this  
can result in a risk of fire or electric shock.  
16. Object and Liquid Entry  
Never push objects of any kind into this  
product through openings as they may touch  
dangerous voltage points or short-out parts  
that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
17. Servicing  
19. Replacement Parts  
When replacement parts are required, be  
sure the service technician has used  
replacement parts specified by the  
manufacturer or have the same  
characteristics as the original part.  
Unauthorized substitutions may result in  
fire, electric shock, or other hazards.  
20. Safety Check  
Do not attempt to service this product  
yourself as opening or removing covers  
may expose you to dangerous voltage or  
other hazards. Refer all servicing to  
qualified service personnel.  
Upon completion of any service or repairs  
to this product, ask the service technician  
to perform safety checks to determine that  
the product is in proper operating  
condition.  
18. Damage Requiring Service  
Unplug this product from the wall outlet  
and refer servicing to qualified service  
personnel under the following conditions:  
a. When the power-supply cord or plug is  
damaged.  
21. Wall or Ceiling Mounting  
This product should be mounted to a wall  
or ceiling only as recommended by the  
manufacturer.  
b. If liquid has been spilled, or objects  
have fallen into the product.  
c. If the product has been exposed to rain  
or water.  
d. If the product does not operate normally  
by following the operating instructions.  
Adjust only those controls that are  
covered by the operating instructions,  
as an improper adjustment of other  
controls may result in damage and will  
often require extensive work by a  
qualified technician to restore the  
product to normal operation.  
22. Heat  
This product should be situated away from  
heat sources such as radiators, heat  
registers, stoves, or other products  
(including amplifiers) that produce heat.  
• DLP® and the DLP logo are registered trademarks of Texas Instruments.  
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the  
United States and/or other countries.  
• PC/AT is a registered trademark of International Business Machines Corporation in the  
United States.  
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.  
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or  
other countries.  
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or  
registered trademarks of HDMI Licensing LLC.  
• All other company or product names are trademarks or registered trademarks of their  
respective companies.  
• Some IC chips in this product include confidential and/or trade secret property belonging  
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,  
reverse engineer, reverse assemble or discompile the contents thereof.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Observe the following safeguards when setting up your  
projector.  
Caution concerning the lamp unit  
When using the projector in high-  
altitude areas such as mountains (at  
altitudes of approximately 1,500  
meters (4,900 feet) or more)  
When you use the projector in high-altitude  
areas with thin air, set “Fan Mode” to  
“High”. Neglecting this can affect the  
longevity of the optical system.  
Potential hazard of glass particles if lamp  
ruptures. In case of lamp rupture, contact  
your nearest Sharp Authorized Projector  
Dealer or Service Center  
for replacement.  
See “Regarding the Lamp”  
on page 78.  
Use the projector at altitudes of 2,300  
meters (7,500 feet) or less.  
Caution concerning the setup of the  
projector  
Warning about placing the projector in  
a high position  
When placing the projector in a high  
position, make certain it is carefully secure  
to avoid personal injury caused by the  
projector falling down.  
For minimal servicing and to maintain high  
image quality, SHARP recommends that  
this projector be installed in an area free  
from humidity, dust and cigarette smoke.  
When the projector is subjected to these  
environments, the vents and lens must be  
cleaned more often. As long as the  
projector is regularly cleaned, use in these  
environments will not reduce the overall  
operation life of the unit. Internal cleaning  
should only be performed by a Sharp  
Authorized Projector Dealer or Service  
Center.  
Do not subject the projector to hard  
impact and/or vibration.  
Protect the lens so as not to hit or damage  
the surface of the lens.  
Avoid locations with extremes of  
temperature.  
The operating temperature of the projector  
is from 41°F to 95°F (+5°C to +35°C).  
The storage temperature of the projector is  
from –4°F to 140°F (–20°C to +60°C).  
Rest your eyes occasionally.  
Continuously watching the screen for long  
hours will cause eye strain. Take regular  
breaks to rest your eyes.  
Do not set up the projector in places  
exposed to direct sunlight or bright light.  
Position the screen so that it is not in direct  
sunlight or room light. Light falling directly  
on the screen washes out the colors,  
making viewing difficult. Close the curtains  
and dim the lights when setting up the  
screen in a sunny or bright room.  
Do not block the exhaust and intake  
vents.  
Allow at least 11 13  
/16 inches (30 cm) of  
space between the exhaust vent and the  
nearest wall or obstruction.  
Ensure that the intake vent and the exhaust  
vent are not obstructed.  
If the cooling fan becomes obstructed, a  
protection circuit will automatically put the  
projector into Standby mode to prevent  
overheat damage. This does not indicate a  
malfunction. (See pages 76 and 77.)  
Remove the projector power cord from the  
wall outlet and wait at least 10 minutes.  
Place the projector where the intake and  
exhaust vents are not blocked, plug the  
power cord back in and turn on the  
projector. This will return the projector to  
the normal operating condition.  
Caution regarding placing of the projector  
Place the projector on a level site within the  
adjustment range (9 degrees) of the  
adjustment foot.  
After the projector is purchased, a faint  
smell from the vent may appear when the  
power is first turned on. This is normal and  
is not a malfunction. It will disappear after  
the projector is used for a while.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution regarding usage of the projector Using the projector in other countries  
If you are not to use the projector for a long  
time or before moving the projector, make  
certain you unplug the power cord from the  
wall outlet, and disconnect any other  
cables connected to it.  
Do not carry the projector by holding the  
lens.  
When storing the projector, ensure you  
attach the lens cover to the projector.  
Do not expose the projector to direct  
sunlight or place next to heat sources.  
Doing so may affect the cabinet color or  
cause deformation of the plastic cover.  
The power supply voltage and the shape of  
the plug may vary depending on the region  
or country you are using the projector in.  
When using the projector overseas, make  
sure you use an appropriate power cord for  
the country you are in.  
Temperature monitor function  
If the temperature inside the projector  
increases, due to blockage of the air vents,  
or the setting location, the temperature  
warning indicator will blink. And if the  
Other connected equipment  
When connecting a computer or other  
audio-visual equipment to the projector,  
make the connections AFTER unplugging  
the power cord of the projector from the  
AC outlet and turning off the equipment to  
be connected.  
Please read the operation manuals of the  
projector and the equipment to be  
connected for instructions on how to make  
the connections.  
temperature keeps on rising, “  
” will  
illuminate in the lower left corner of the  
picture with the temperature warning  
indicator blinking. If this state continues,  
the lamp will turn off, the cooling fan will  
run and then the projector will enter  
Standby mode. Refer to “Maintenance  
Indicators” on pages 76 and 77 for details.  
Info  
• The cooling fan regulates the internal  
temperature, and its performance is automatically  
controlled. The sound of the fan may change  
during projector operation due to changes in the  
fan speed. This does not indicate malfunction.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Observe the following safeguards when using the 3D Glasses.  
Prevention of accidental ingestion  
Using the 3D Glasses  
Keep the batteries and band accessory out  
of the reach of small children. Small children  
can accidentally swallow these parts.  
Parents/guardians should monitor  
children’s viewing habits to avoid their  
prolonged use without rest periods.  
Use only the 3D Glasses recommended for  
this product.  
If a child accidentally swallows any of these  
parts, seek immediate medical attention.  
Use the 3D Glasses only for the specified  
purpose.  
Do not move around while wearing the 3D  
Glasses. The surrounding area appears  
dark, which may result in falling or other  
accidents that may cause injury.  
Do not disassemble  
Do not disassemble or modify the 3D Glasses.  
Caution for lithium battery  
Batteries must not be exposed to excessive  
heat such as direct sunlight or fire.  
Replace only with the same or equivalent  
type of battery. The battery may explode if  
improperly replaced.  
Take care not to reverse the battery poles  
(+ and –) when loading the battery. Follow  
the correct procedure when loading the  
battery. (See page 65.) Loading the battery  
incorrectly may damage the battery or  
cause it to leak battery fluid, which could  
result in a fire, injury or damage.  
Caring for the 3D Glasses  
Use only the cloth provided with the 3D Glasses  
to clean the lenses. Remove dust and soil from  
the cloth. Any dust or other soiling on the cloth  
may result in scratches on the product. Do not  
use solvents such as benzene or thinners as  
doing so may cause the coating to peel off.  
When cleaning the 3D Glasses, take care  
not to allow water or other fluids to come  
into contact with the glasses.  
Always store the 3D Glasses in the case  
provided when not in use.  
When storing the 3D Glasses, avoid very  
humid or hot locations.  
Handling the 3D Glasses  
Do not drop, exert pressure on, or step on  
the 3D Glasses. Doing so may damage the  
glass section, which may result in injury.  
Be careful not to trap your finger in the  
hinge section of the 3D Glasses. Doing so  
may result in injury.  
Viewing 3D images  
If you experience dizziness, nausea, or  
other discomfort while viewing 3D images,  
discontinue use and rest your eyes.  
Do not use the 3D Glasses if they are  
cracked or broken.  
– Pay special attention when children are  
using this product.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Access the PDF Operation Manuals  
PDF operation manuals in several languages are included in the CD-ROM. To  
utilize these manuals, you need to install Adobe® Reader® on your computer  
(Windows® or Macintosh®).  
Please download Adobe® Reader® from the Internet (http://www.adobe.com).  
Accessing the PDF Manuals  
For Macintosh®:  
For Windows®:  
Insert the CD-ROM in the CD-ROM drive.  
Double click the “CD-ROM” icon.  
When you want to view the operation  
manual  
Insert the CD-ROM in the CD-ROM drive.  
Double click the “My Computer” icon.  
Double click the “CD-ROM” drive.  
When you want to view the operation  
manual  
1) Double click the “MANUALS” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the pdf file to access the  
projector manuals.  
When you want to view the SETUP  
MANUAL  
1) Double click the “SETUP” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the pdf file to access the  
SETUP MANUAL.  
1) Double click the “MANUALS” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the pdf file to access the  
projector manuals.  
When you want to view the SETUP  
MANUAL  
1) Double click the “SETUP” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the pdf file to access the  
SETUP MANUAL.  
Note  
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® fi r s t ,  
then specify the desired file using the “File”, “Open” menu.  
SETUP MANUAL  
Refer to the “SETUP MANUALcontained on the supplied CD-ROM for details.  
Connecting Pin Assignments ·······················································2  
RS-232C Specifications and Commands·····································4  
Setting up the Projector Network Environment ····························8  
Resetting the Lamp Timer of the Projector via LAN···················· 13  
Troubleshooting·········································································· 15  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
Supplied accessories  
Two R-6 batteries  
(“AA” size, UM/SUM-3,  
HP-7 or similar)  
Two pairs of 3D Glasses*1  
<KOPTLA002WJN1>  
Remote control  
<RRMCGA999WJSA>  
IR emitter  
<PSETNA007FMF0>  
IR emitter cable  
<QCNWGA170WJPZ>  
Power cord*2  
(1)  
(2)  
(3)  
For U.S. and  
Canada, etc.  
(6' (1.8 m))  
For Europe,  
except U.K.  
(6' (1.8 m))  
For Australia, New  
Zealand and Oceania  
(6' (1.8 m))  
<QACCDA082WJPZ>  
<QACCVA024WJPZ>  
<QACCLA138WJPZ>  
*1 See pages 64 to 66 for details of the 3D Glasses and their accessories.  
*2 Which power cords are supplied along with your projector depends on the region. Use the power  
cord that corresponds to the wall outlet in your country.  
• Operation manuals (this manual <TINS-F383WJZZ> and CD-ROM <UDSKAA138WJZZ>)  
Note  
• Codes in “< >” are Replacement parts codes.  
Optional accessories  
AN-K30LP  
AN-60KT  
AN-XGCM55 (for U.S.A. only)  
AN-TK201 <for AN-60KT>  
AN-TK202 <for AN-60KT>  
AN-EP101B <for AN-XGCM55>  
(for U.S.A. only)  
Lamp unit  
Ceiling-mount adaptor  
Ceiling-mount bracket  
Ceiling-mount unit  
Ceiling-mount extension tube  
AN-C3CP2  
AN-3DG10-S  
3 RCA to mini D-sub 15 pin cable (10' (3.0 m))  
3D Glasses  
Note  
• Some of the optional accessories may not be available depending on the region. Please check with  
your nearest Sharp Authorized Projector Dealer or Service Center.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
Numbers in Z refer to the main pages in this operation manual where the  
topic is explained.  
1
2
3
4
5
6
7
8
9 10  
11  
12  
13  
14 15 16 17  
8
9
KEYSTONE button  
31  
Side View  
For entering the Keystone Correction  
mode.  
28  
STANDBY/ON button  
1
For turning the power on and putting the  
projector into Standby mode.  
3D MENU button  
For displaying the 3D MENU screen.  
69, 70  
2
LENS button  
10 RESIZE button  
36  
For toggling the menu screens for  
adjustments of the lens (LENS SHIFT,  
FOCUS, ZOOM, etc.).  
For switching the picture size (NORMAL,  
16:9, etc.).  
42  
RETURN button  
3
4
Top View  
For returning to the previous menu screen  
during menu operations.  
11 Power indicator  
12 Lamp indicator  
13 Temperature warning indicator  
76  
76  
42  
ENTER button  
For setting items selected or adjusted on  
the menu.  
76  
5
6
7
INPUT buttons (R/P)  
35  
For switching input mode.  
Front View  
42  
Adjustment buttons (P/R/O/Q)  
For selecting menu items.  
14 Exhaust vent  
15 Adjustment foot  
30  
16 Remote control sensor  
75  
42  
MENU button  
For displaying adjustment and setting  
screens.  
17  
17 Lens cover  
75  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions (Continued)  
1
2
3
4
5
6
7
8
9
10 11  
12 13  
Rear View (Terminals)  
1
COMPUTER/COMPONENT input  
terminal  
Terminal for computer RGB and  
component signals.  
7
3D SYNCHRO terminal  
67  
23, 25  
Terminal for connecting the IR emitter.  
8
9
Exhaust vent  
75  
Rear adjustment foot  
2
Component (YPB(CB)PR(CR)) terminals  
23  
Terminals for connecting video equipment  
with component output terminal.  
30  
10 Intake vent  
11 Kensington Security Standard  
75  
connector  
3
4
HDMI terminals  
23, 24  
12 Remote control sensor  
17  
Terminals for HDMI input.  
13 AC socket  
27  
LAN terminal  
27  
Connect the supplied power cord.  
Terminal for controlling the projector using  
a computer via network.  
Using the Kensington Lock  
5
TRIGGER terminal  
51  
• This projector has a Kensington Security  
Standard connector for use with a  
Kensington MicroSaver Security System.  
Refer to the information that came with the  
system for instructions on how to use it to  
secure the projector.  
When the projector is turned on, a control  
signal (DC 12V) is output from this terminal.  
This can be connected to a retractable  
projection screen or anamorphic lens that  
supports the trigger function.  
6
RS-232C terminal  
Terminal for controlling the projector using  
a computer.  
26  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Numbers in Z refer to the main pages in this operation manual where the  
topic is explained.  
30  
10 ZOOM buttons  
For adjusting the projected image size.  
29  
1
11 H&V SHIFT button  
For shifting the lens horizontally and vertically.  
38  
2
3
12 AUTO SYNC button  
For automatically adjusting images when  
connected to a computer.  
4
56  
13 MEMORY 1/2 buttons  
For displaying each “Load Memory” screen of  
“Memory Menu”.  
5
6
7
8
9
15  
56  
MEMORY button  
For displaying the Memory Menu screen.  
16  
17  
18  
68, 69  
14 3D ON/OFF button  
For switching between 2D and 3D modes.  
38  
15 IRIS 1/2 buttons  
For adjusting the quantity of the projected  
light and the contrast of the image.  
19  
20  
21  
10  
42  
16 MENU button  
11  
12  
13  
14  
For displaying adjustment and setting  
screens.  
42  
17 ENTER button  
22  
For setting items selected or adjusted on the  
menu.  
38  
18 MENU HIDE button  
For temporarily hiding menu screen.  
30  
19 FOCUS buttons  
For adjusting the focus.  
31  
28  
1
2
ON button  
For turning the power on.  
20 KEYSTONE button  
For entering the Keystone Correction mode.  
38  
28  
STANDBY button  
For putting the projector into the Standby  
mode.  
21 ECO+QUIET button  
For lowering the noise of the cooling fan and  
3
4
CONTRAST, BRIGHTNESS, COLOR and  
TINT buttons  
For adjusting the contrast, brightness, color  
and tint.  
extending the lamp life.  
37  
69, 70  
22 3D MENU button  
For displaying the 3D MENU screen.  
HDMI 1/2, COMPONENT and COMPUTER  
buttons  
35  
For switching to the respective input modes.  
37  
5
6
PICTURE MODE button  
For displaying the Picture Mode list.  
36  
RESIZE button  
For switching the picture size (NORMAL, 16:9,  
etc.).  
7
8
9
ANAMORPHIC button  
For switching the Anamorphic lens.  
42  
Adjustment buttons (P/R/O/Q)  
For selecting and adjusting menu items.  
42  
RETURN button  
For returning to the previous menu screen  
during menu operations.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions (Continued)  
Inserting the Batteries  
Pull down the tab on the cover and remove the  
cover towards the direction of the arrow.  
1
Insert the batteries.  
2
• Insert the batteries making sure the polarities correctly match  
the m and n marks inside the battery compartment.  
Insert the upper tab of the cover into the opening,  
and lower the cover until it clicks in place.  
3
Incorrect use of the batteries may cause them to leak or explode.  
Please follow the precautions below  
Caution  
• Danger of explosion if battery is incorrectly replaced.  
Replace only with alkaline or manganese batteries.  
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery  
compartment.  
• Batteries of different types have different properties, therefore do not mix batteries of different types.  
• Do not mix new and old batteries.  
This may shorten the life of new batteries or may cause old batteries to leak.  
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.  
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then  
remove them using a cloth.  
• The batteries included with this projector may run down in a short period, depending on how they are kept.  
Be sure to replace them as soon as possible with new batteries.  
• Remove the batteries from the remote control if you will not be using the remote control for a long time.  
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usable Range  
The remote control can be used to control the  
projector within the ranges shown in the  
illustration.  
Remote control sensor  
Note  
• Another remote control sensor is located  
on the rear of the projector. (See pages  
13 and 14.)  
30°  
• The signal from the remote control can be  
reflected off a screen for easy operation.  
However, the effective distance of the signal  
may differ depending on the screen material.  
30°  
33n (10 m)  
When using the remote control  
• Ensure that you do not drop it or expose it to  
moisture or high temperature.  
• The remote control may malfunction under a  
fluorescent lamp. In this case, move the  
projector away from the fluorescent lamp.  
Remote control signal  
transmitters  
Remote control  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Easy Start  
This section shows the basic operation (projector connecting with video equipment). For details,  
see the page described below for each step.  
Setup and Projection  
In this section, connection of the projector and video equipment is explained using one  
example.  
8 STANDBY button  
3, 8 STANDBY/ON button  
3 ON button  
6 ENTER button  
6 R/P buttons, 7 INPUT buttons  
7 HDMI 1/2,  
COMPONENT  
and COMPUTER  
buttons  
6 O/Q buttons  
6 KEYSTONE  
button  
4, 6 Adjustment  
buttons  
(P/R/O/Q)  
6 ENTER button  
4 H&V SHIFT button  
5 FOCUS buttons  
5 ZOOM buttons  
6 KEYSTONE button  
P. 20  
B
1. Place the projector facing a wall or a screen  
2.Connect the projector to the video equipment and plug the  
power cord into the AC socket of the projector  
BPP. 23 to 27  
3. Turn the projector on  
Press STANDBY/ON on the projector or ON on the remote control.  
BP. 28  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Adjust the angle  
Adjust the projector angle:  
• Shift the lens horizontally and vertically.  
1 Press H&V SHIFT on the remote control.  
2 Press P, R, O or Q on the remote control.  
• Adjust the projector angle by rotating the  
adjustment feet.  
BPP. 29, 30  
5. Adjust the focus and the zoom  
1 Press FOCUS +/– on the remote control to adjust the focus.  
2 Press ZOOM +/– on the remote control to adjust the zoom.  
BP. 30  
6. Correcting the image distortion due to the projection angle  
1
2
3
4
5
Press KEYSTONE on the projector or on the remote control.  
Press ENTER on the projector or on the remote control.  
Press P, R, O or Q to move the position for the upper left of the image.  
Press ENTER to set the position.  
Repeat the same procedure with the positions for the upper right, lower right and lower  
left of the image.  
• When the position of the lower left is set, the correction is  
made and the display disappears.  
BP. 31  
7. Select the Input mode  
On the projector:  
Press INPUT R/P to display the INPUT list. Use INPUT R/P to select the input mode.  
INPUT list  
On-screen display (HDMI1)  
HDMI1  
YPbPr  
INPUT  
HDMI1  
1080P  
HDMI2  
COMPUTER  
COMPONENT  
On the remote control:  
Press HDMI 1/2, COMPONENT or COMPUTER to  
select the input mode.  
BP. 35  
8. Turn the power off  
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press  
the button again while the confirmation message is displayed to put the projector into  
Standby mode.  
On-screen display  
On the  
projector  
On the remote  
control  
BP. 28  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector  
Video Setup  
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See  
page 50.)  
Setting Up the Projector  
For optimal image quality, position the projector perpendicular to the screen with the projector's  
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best  
image quality. (See pages 31 to 34.)  
Standard Setup (Front Projection)  
Place the projector at the required distance from the screen according to the desired picture  
size. (See page 21.)  
Indication of the Projection Image Size and Projection Distance  
Example: When using a wide screen (16:9)  
Picture Size  
500" (1270 cm)  
436  
"
×
245  
(1107 cm  
"
200" (508 cm)  
×
623  
174"  
cm )  
×
98"  
(443 cm  
100" (254 cm)  
80" (203 cm)  
40" (102 cm)  
87"  
×
249 cm)  
×
49"  
(221 cm  
70"  
Projection  
Distance  
×
×
39"  
125 cm)  
100 cm)  
(177 cm  
35"  
×
×
20"  
×
(89 cm  
50 cm)  
4'2" - 8'4"  
(1.3 m - 2.5 m)  
8'3" - 16'8"  
(2.5 m - 5.1 m)  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screen Size and Projection Distance  
When using a wide screen (16:9): In case of displaying the 16:9 picture on the whole of the  
16:9 screen  
Distance from the lens center  
to the bottom of the image [H]  
Distance from the  
lens center to the  
Picture (Screen) size  
Projection distance [L]  
center of the image[W]  
Diag. [  
x
]
Width  
Height  
Minimum [L1]  
Maximum [L2]  
31.7 m (103' 11")  
25.3 m (83' 2")  
19.0 m (62' 4")  
Lower[H1]  
-623 cm (-245 9  
-498 cm (-196 7  
-374 cm (-147 5  
-311 cm (-122 9  
Upper[H2]  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
500" (1270 cm) 1107 cm (436") 623 cm (245") 15.7 m (51' 7")  
/64")  
/64")  
/64")  
/16")  
210 cm  
168 cm  
126 cm  
105 cm  
84 cm  
63 cm  
50 cm  
42 cm  
34 cm  
25 cm  
17 cm  
(
(
(
(
(
(
(
(
(
(
(
82 51  
66 15  
49 43  
41 13  
/
/
/
/
64")  
64")  
64")  
32")  
400" (1016 cm)  
300" (762 cm)  
250" (635 cm)  
200" (508 cm)  
150" (381 cm)  
120" (305 cm)  
100" (254 cm)  
80" (203 cm)  
60" (152 cm)  
40" (102 cm)  
886 cm (349") 498 cm (196") 12.6 m (41' 4")  
664 cm (261") 374 cm (147")  
553 cm (218") 311 cm (123")  
443 cm (174") 249 cm (98")  
332 cm (131") 187 cm (74")  
266 cm (105") 149 cm (59")  
221 cm (87")  
177 cm (70")  
133 cm (52")  
89 cm (35")  
9.4 m (31' 0")  
7.9 m (25' 10") 15.8 m (52' 0")  
6.3 m (20' 8")  
4.7 m (15' 6")  
3.8 m (12' 5")  
3.1 m (10' 4")  
2.5 m (8' 3")  
1.9 m (6' 2")  
1.3 m (4' 2")  
12.7 m (41' 7")  
9.5 m (31' 2")  
7.6 m (24' 11")  
6.3 m (20' 9")  
5.1 m (16' 8")  
3.8 m (12' 6")  
2.5 m (8' 4")  
-249 cm (-98 1  
/
16")  
64")  
64")  
33 1  
/
8")  
-187 cm (-73 35  
/
24 27  
/32")  
-149 cm (-58 53  
/
19 7  
16 9  
13 1  
/
/
/
8")  
16")  
4")  
125 cm (49")  
100 cm (39")  
75 cm (29")  
50 cm (20")  
-125 cm (-49 1  
-100 cm (-39 7  
/
32")  
32")  
/
-75 cm (-29 27  
-50 cm (-19 39  
/
64")  
64")  
9 15  
/
16")  
/
6 5  
/8")  
x
: Picture size (diag.) (in/cm): 40" – 500"  
The formula for picture size and projection distance  
L1 : Minimum projection distance (m/ft)  
L2 : Maximum projection distance (m/ft)  
[m/cm]  
[Feet/inches]  
L1 (m)  
= 0.03147 x  
L1 (ft) = 0.03147 x / 0.3048  
L2 (ft) = 0.06337 x / 0.3048  
H1 (in) = -1.2453 x / 2.54  
H2 (in) = 0 x / 2.54  
H1 : Lower distance from the lens center to the bottom of the image (cm/in)  
H2 : Upper distance from the lens center to the bottom of the image (cm/in)  
L2 (m)  
= 0.06337 x  
H1 (cm) = -1.2453 x  
W
:
Distance from the lens center to the center of the image cm/in)  
H2 (cm) = 0 x  
W
(cm) = 0.42062 x  
W
(in) = 0.42062 x / 2.54  
When using a normal screen (4:3): In case of displaying the 4:3 picture on the whole of the  
4:3 screen.  
Distance from the lens center  
to the bottom of the image [H]  
Distance from the  
lens center to the  
Picture (Screen) size  
Projection distance [L]  
center of the image[W]  
Diag. [  
x
]
Width  
Height  
Minimum [L1]  
Maximum [L2]  
31.0 m (101' 9")  
Lower[H1]  
-610 cm (-240")  
-457 cm (-180")  
-381 cm (-150")  
-305 cm (-120")  
-229 cm (-90")  
-183 cm (-72")  
-152 cm (-60")  
-122 cm (-48")  
-107 cm (-42")  
-91 cm (-36")  
Upper[H2]  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
400" (1016 cm)  
300" (762 cm)  
250" (635 cm)  
200" (508 cm)  
150" (381 cm)  
120" (305 cm)  
100" (254 cm)  
80" (203 cm)  
70" (178 cm)  
60" (152 cm)  
40" (102 cm)  
813 cm (320") 610 cm (240") 15.4 m (50' 6")  
206 cm  
154 cm  
129 cm  
103 cm  
77 cm  
62 cm  
51 cm  
41 cm  
36 cm  
31 cm  
21 cm  
(
(
(
(
(
(
(
(
(
(
(
81 1  
/
16")  
610 cm (240") 457 cm (180") 11.6 m (37' 11") 23.3 m (76' 4")  
60 51  
50 43  
40 17  
30 13  
/
/
/
/
16")  
/
32")  
16")  
32")  
64")  
508 cm (200") 381 cm (150")  
406 cm (160") 305 cm (120")  
305 cm (120") 229 cm (90")  
244 cm (96")  
203 cm (80")  
163 cm (64")  
142 cm (56")  
122 cm (48")  
81 cm (32")  
9.6 m (31' 7")  
7.7 m (25' 3")  
19.4 m (63' 7")  
15.5 m (50' 11")  
64")  
32")  
32")  
5.8 m (18' 11") 11.6 m (38' 2")  
183 cm (72")  
152 cm (60")  
122 cm (48")  
107 cm (42")  
91 cm (36")  
61 cm (24")  
4.6 m (15' 2")  
3.9 m (12' 8")  
3.1 m (10' 1")  
2.7 m (8' 10")  
2.3 m (7' 7")  
1.5 m (5' 1")  
9.3 m (30' 6")  
7.8 m (25' 5")  
6.2 m (20' 4")  
5.4 m (17' 10")  
4.7 m (15' 3")  
3.1 m (10' 2")  
24 5  
/
20 17  
64")  
16 7  
14 3  
12 5  
/
/
/
-61 cm (-24")  
8 7  
/
64")  
x
: Picture size (diag.) (in/cm): 40" – 400"  
The formula for picture size and projection distance  
L1 : Minimum projection distance (m/ft)  
L2 : Maximum projection distance (m/ft)  
[m/cm]  
[Feet/inches]  
L1 (m)  
= 0.03851 x  
L1 (ft) = 0.03851 x / 0.3048  
L2 (ft) = 0.07755 x / 0.3048  
H1 (in) = -1.52404 x / 2.54  
H2 (in) = 0 x / 2.54  
H1 : Lower distance from the lens center to the bottom of the image (cm/in)  
H2 : Upper distance from the lens center to the bottom of the image (cm/in)  
L2 (m)  
= 0.07755 x  
H1 (cm) = -1.52404 x  
W
:
Distance from the lens center to the center of the image cm/in)  
H2 (cm) = 0 x  
W
(cm) = 0.51477 x  
W
(in) = 0.51477 x / 2.54  
When using a normal screen (4:3): In case of setting the 16:9 picture to the full horizontal  
width of the 4:3 screen  
Distance from the lens center  
to the bottom of the image [H]  
Distance from the  
lens center to the  
Picture (Screen) size  
Projection distance [L]  
center of the image[W]  
Diag. [  
x
]
Width  
Height  
Minimum [L1]  
Maximum [L2]  
29.1 m (95' 5")  
Lower[H1]  
-572 cm (-225")  
-457 cm (-180")  
-343 cm (-135")  
Upper[H2]  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
0 cm (0")  
500" (1270 cm) 1016 cm (400") 762 cm (300") 14.4 m (47' 5")  
193 cm  
154 cm  
116 cm  
97 cm  
77 cm  
58 cm  
46 cm  
39 cm  
31 cm  
27 cm  
23 cm  
15 cm  
(
(
(
(
(
(
(
(
(
(
76")  
400" (1016 cm)  
300" (762 cm)  
250" (635 cm)  
200" (508 cm)  
150" (381 cm)  
120" (305 cm)  
100" (254 cm)  
80" (203 cm)  
70" (178 cm)  
60" (152 cm)  
40" (102 cm)  
813 cm (320") 610 cm (240") 11.6 m (37' 11") 23.3 m (76' 4")  
60 51  
45 19  
38")  
/
64")  
32")  
610 cm (240") 457 cm (180")  
508 cm (200") 381 cm (150")  
406 cm (160") 305 cm (120")  
305 cm (120") 229 cm (90")  
244 cm (96")  
203 cm (80")  
163 cm (64")  
142 cm (56")  
122 cm (48")  
81 cm (32")  
8.7 m (28' 5")  
7.2 m (23' 8")  
17.5 m (57' 3")  
14.5 m (47' 9")  
/
-286 cm (-112 1  
-229 cm (-90")  
/
2")  
5.8 m (18' 11") 11.6 m (38' 2")  
30 13  
22 51  
18 15  
15 13  
/
/
/
/
32")  
64")  
64")  
64")  
4.3 m (14' 3")  
3.5 m (11' 4")  
2.9 m (9' 6")  
2.3 m (7' 7")  
2.0 m (6' 8")  
1.7 m (5' 8")  
1.2 m (3' 9")  
8.7 m (28' 8")  
7.0 m (22' 11")  
5.8 m (19' 1")  
4.7 m (15' 3")  
4.1 m (13' 4")  
3.5 m (11' 5")  
2.3 m (7' 8")  
-171 cm (-67 1  
/
2")  
183 cm (72")  
152 cm (60")  
122 cm (48")  
107 cm (42")  
91 cm (36")  
61 cm (24")  
-137 cm (-54")  
-114 cm (-45")  
-91 cm (-36")  
12 5  
/
32")  
-80 cm (-31 1  
-69 cm (-27")  
-46 cm (-18")  
/
2")  
10 41  
/64")  
(
9 1  
6 5  
/
/
8")  
64")  
(
x
: Picture size (diag.) (in/cm): 40" – 500"  
The formula for picture size and projection distance  
L1 : Minimum projection distance (m/ft)  
L2 : Maximum projection distance (m/ft)  
[m/cm]  
[Feet/inches]  
L1 (m)  
= 0.02889 x  
L1 (ft) = 0.02889 x / 0.3048  
L2 (ft) = 0.05817 x / 0.3048  
H1 (in) = -1.14303 x / 2.54  
H2 (in) = 0 x / 2.54  
H1 : Lower distance from the lens center to the bottom of the image (cm/in)  
H2 : Upper distance from the lens center to the bottom of the image (cm/in)  
L2 (m)  
= 0.05817 x  
H1 (cm) = -1.14303 x  
W
:
Distance from the lens center to the center of the image cm/in)  
H2 (cm) = 0 x  
W
(cm) = 0.38608 x  
W
(in) = 0.38608 x / 2.54  
Note  
• When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates  
that the bottom of the image is below the lens center.  
• Allow a margin of error in the value in the diagrams above.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector (Continued)  
Projection (PRJ) Mode  
The projector can use any of the 4 projection modes shown in the diagram below. Select the  
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-  
ADJ” menu. See page 53.)  
Table mounted, front projection  
Ceiling mounted, front projection  
[Menu item “Front”]  
[Menu item “Ceiling + Front”]  
Ceiling mounted, rear projection  
(with a translucent screen)  
Table mounted, rear projection  
(with a translucent screen)  
[Menu item “Rear”]  
[Menu item “Ceiling + Rear”]  
a
Ceiling-Mount Setup  
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this  
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector  
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold  
separately).  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Projector to Other Equipment  
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet  
and turn off the equipment to be connected. After making all connections, turn on the projector  
and then the other pieces of equipment. When connecting a computer, ensure that it is the last  
equipment to be turned on after all the connections are made.  
For more details of connection and cables, refer to the operation manual of the connecting equipment.  
• You may need other cables or connectors not listed below.  
Terminals on the Projector  
Terminal on  
connected equipment  
Terminal on the  
projector  
Equipment  
Cable  
Video equipment  
HDMI cable (commercially available)  
HDMI 1, 2  
HDMI output  
terminal  
3 RCA to mini D-sub 15 pin cable  
COMPUTER/  
COMPONENT  
Component  
video output  
terminal  
Component cable (commercially available)  
Component  
(YPB(CB)PR(CR))  
Camera/Video game  
Cables for a camera or a video game/3 RCA to COMPUTER/  
mini D-sub 15 pin cable  
COMPONENT  
Component  
video  
output terminal  
RCA adaptor plug  
(commercially available)  
RGB cable (supplied)  
COMPUTER/  
COMPONENT  
Computer  
RGB output  
terminal  
HDMI cable (commercially available)  
HDMI 1, 2  
HDMI output  
terminal  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment  
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and  
turn off the devices to be connected. After making all connections, turn on the projector and  
then the other devices.  
Connecting Equipment with HDMI Output Terminal to the HDMI Terminal on the  
Projector  
For video connection, use a cable that conforms to HDMI standards. Using cables that do not  
conform to HDMI standards may result in a malfunction.  
HDMI-compatible device  
To HDMI output terminal  
To HDMI1 or 2 terminal  
HDMI cable (type A) (commercially available)  
Note  
• Depending on specifications of equipment or the DVIÙHDMI digital cable, the signal transmission  
may not work property. (The HDMI specification does not support all connections to equipment that  
has digital output terminal using a DVIÙHDMI digital cable.)  
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition  
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.  
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the  
digital video signal does not degrade when transmitted, and a high-quality image with a simple  
connection can be enjoyed.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Computer  
Ensure that the computer is the last device to be turned on after all the connections are made.  
Connecting to a computer using the RGB cable  
Computer  
To RGB output terminal  
To COMPUTER/COMPONENT terminal  
RGB cable (commercially available)  
Note  
• See page 81 “Compatibility Chart” for a list of computer signals compatible with the projector. Use  
with computer signals other than those listed may cause some of the functions to not work.  
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest  
Macintosh Dealer.  
• Depending on the computer you are using, an image may not be projected unless the  
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys  
simultaneously when using a SHARP notebook computer). Refer to the specific instructions in  
your computer's operation manual to enable your computer's external output port.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling the Projector by a Computer  
When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial  
control cable (cross type, commercially available), the computer can be used to control the  
projector and check the status of the projector. Refer to the “SETUP MANUALcontained on the  
supplied CD-ROM for “RS-232C Specifications and Commands”.  
When connecting to a computer using an RS-232C serial control cable  
To RS-232C terminal  
Computer  
To RS-232C terminal  
RS-232C serial control cable (cross type, commercially available)  
Note  
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the  
operation manual of the computer for details.  
• Refer to pages 2 to 7 of the “SETUP MANUALcontained on the supplied CD-ROM for “Connecting  
Pin Assignments” and “RS-232C Specifications and Commands”.  
Info  
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This  
may damage your computer or projector.  
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.  
This may damage your computer.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When connecting to the LAN terminal using a LAN cable  
LINK LED (green)  
Illuminates when linked.  
TX/RX LED (yellow)  
Illuminates when transmitting/receiving data.  
* To ensure safety, do not connect the LAN terminal  
with any cables that may cause excessive voltage  
such as a telephone line.  
Hub  
or  
Computer  
To LAN terminal  
LAN cable (Category 5 type,  
commercially available)  
Note  
• When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially  
available).  
• When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially  
available).  
Connecting the Power Cord  
Plug the supplied power cord into the AC  
socket on the rear of the projector. Then  
plug into AC outlet.  
AC socket  
Power cord (supplied)  
To AC outlet  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the Projector On/Off  
Info  
• English is the factory default language. If you  
want to change the on-screen display to  
another language, change the language  
according to the procedure on page 53.  
Turning the Projector On  
Note that the connections to external  
equipment and power outlet should be  
done before performing the operations  
written below. (See pages 23 to 27.)  
STANDBY/ON button  
Press STANDBY/ON on the projector  
Power indicator  
Lamp indicator  
or ON on the remote control.  
• The power indicator illuminates green.  
• After the lamp indicator illuminates, the projector  
is ready to start operation.  
Note  
• About the Lamp Indicator  
The lamp indicator illuminates to indicate the  
status of the lamp.  
Green: The lamp is on.  
Blinking in green: The lamp is warming up.  
Red: The lamp is shut down  
abnormally or the lamp should be  
replaced.  
• When switching on the projector, a slight  
flickering of the image may be experienced  
within the first minute after the lamp has been  
illuminated. This is normal operation as the  
lamp's control circuitry is stabilising the lamp  
output characteristics. It should not be  
regarded as faulty operation.  
STANDBY  
button  
• If the projector is put into Standby mode and  
immediately turned on again, the lamp may  
take some time to start projection.  
ON button  
On-screen display (confirmation message)  
Turning the Power Off (Putting  
the Projector into Standby Mode)  
Press STANDBY/ON on the projector  
or STANDBY on the remote control,  
then press that button again while the  
confirmation message is displayed, to  
Info  
put the projector into Standby mode.  
• The projector cannot be turned on while cooling.  
• Direct Power Off function:  
You can unplug the power cord from the AC  
outlet even if the cooling fan is still running.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Shifting the Lens  
In addition to the zoom function and adjustment of projection angle using the  
adjustment feet, you can adjust the position of the projection using the lens shift  
function. This is a useful function in cases such as when the screen cannot be moved.  
When moving upward or downward When moving in the left and right direction  
ange  
le r  
Adjustab  
ange  
le r  
Adjustab  
Adjustable  
range  
Adjustable range  
• The adjustable range is shown below.  
Horizontal range: 20%  
ENTER button  
Vertical range: 50%  
Adjustment buttons  
(P/R/O/Q)  
The adjustable range has limitations even  
within the range shown above.  
• The image can be adjusted as shown on the  
diagram.  
RETURN button  
• Allow a margin of error in the value.  
H&V SHIFT button  
Press H&V SHIFT on the remote  
1
control.  
• Pressing ENTER on the projector or on  
the remote control displays the test  
pattern. Checking the test pattern is useful  
for more accurate adjustment.  
Position of the image when the image is  
centered, both vertically and horizontally,  
in lens shift  
ROn-screen display  
0.5V  
LENS SHIFT  
END  
LENS SHIFT  
TESTPATTERN  
LENS CENTER  
1V  
Press P, R, O or Q on the  
projector or the remote control  
to adjust the image position.  
2
0.5V  
Note  
0.2H  
1H  
0.2H  
• When RETURN is pressed, the lens shift  
reset screen is displayed. Lens shift can be  
reset to factory default with this screen.  
V : Height of the image  
H : Width of the image  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Using the Adjustment Feet  
• When the position of the projected image cannot  
be adjusted with the lens shift function, use the  
adjustment feet to adjust the projected angle.  
• The height of the projector can be adjusted using  
the adjustment feet when the screen is located  
higher than the projector, the screen is inclined or  
when the installation site is slightly inclined.  
Adjustment feet  
• Install the projector so that it is as perpendicular  
to the screen as possible.  
Down  
Up  
Rotate the adjustment feet to  
Up  
Down  
adjust the projected angle.  
• The projector is adjustable up to approximately 9  
degrees (front) and approximately 2 degrees  
(rear) from the standard position.  
Warning!  
• Do not hold the lens and lens cover when  
projector angle is adjusted.  
• Use caution not to pinch your finger in the  
space between the adjustment foot and the  
projector when the projector angle is lowered.  
Adjusting the Focus  
Press FOCUS +/– on the remote  
control to adjust the focus.  
ROn-screen display  
ZOOM buttons  
FOCUS buttons  
FOCUS  
TESTPATTERN  
Info  
• It is recommended that the focus be adjusted  
after the projector has warmed up for at least  
30 minutes.  
Note  
• After you have pressed FOCUS or ZOOM on  
the remote control, you can display the test  
pattern by pressing ENTER. The test pattern  
is useful for making more accurate  
adjustments.  
• For fine adjustments, when H&V SHIFT,  
FOCUS or ZOOM is pressed, the projected  
image moves a small amount in the desired  
direction for approximately one second. Hold  
down the buttons to move the projected  
image quickly.  
Adjusting the Projected  
Image Size  
Press ZOOM +/– on the remote control  
to adjust the projected image size.  
ROn-screen display  
ZOOM  
TESTPATTERN  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Correcting Trapezoidal Distortion  
When the image is projected either from the top or from the bottom towards the  
screen at an angle, the image becomes distorted trapezoidally.  
The function for correcting trapezoidal distortion is called Keystone Correction.  
There are three types of the Keystone Correction.  
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner  
of the projected image  
2) “H&V KEYSTONE” for designating the correction of the horizontal and  
vertical axes  
3) “SPHERE” for correcting the distortion of an image projected on a spherical  
or cylindrical screen  
Selecting the Type of the Correction  
Press KEYSTONE.  
1
• The KEYSTOME MODE list appears.  
ENTER button  
KEYSTONE MODE  
Adjustment buttons  
GEOMETRIC ADJUSTMENT  
(P/R/O/Q)  
H&V KEYSTONE  
RETURN button  
SPHERE  
SEL.  
ENTER  
END  
KEYSTONE button  
Press P/R to select the desired  
2
3
Keystone mode, and then press  
RETURN button  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
KEYSTONE button  
ENTER.  
• The menu guide appears.  
Press P/R/O/Q to adjust the  
Keystone Correction.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
GEOMETRIC ADJUSTMENT  
ROn-screen display  
Press KEYSTONE.  
• The KEYSTONE MODE list appears. (See  
page 31.)  
1
2
3
GEOMETRIC ADJUSTMENT  
ADJUST  
RESET  
H&V KEYSTONE  
NEXT  
Press P/R to select  
“GEOMETRIC ADJUSTMENT”,  
and then press ENTER.  
Press P, R, O or Q to move the  
position for the upper left of the  
image.  
Geometric Adjustment  
Upper Left Upper Right Lower Right  
Press ENTER to set the position.  
4
5
Repeat the same procedure with  
the positions for the upper right,  
lower right and lower left of the  
image.  
• At this time, pressing RETURN on the  
projector or on the remote control returns  
to the previous screen.  
Lower Left  
• When the position of the lower left is  
set, the correction is made and the  
display disappears.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H&V KEYSTONE  
ROn-screen display  
Press KEYSTONE.  
1
2
• The KEYSTONE MODE list appears. (See  
page 31.)  
H&V KEYSTONE  
END  
H:0  
V:0  
ADJUST  
EXIT TEST PTRN  
RESET  
Press P/R to select “H&V  
KEYSTONE”, and then press  
ENTER.  
Press P or R to parallelize the  
left and right sides of the  
projected image.  
3
4
5
Vertical Keystone Correction  
(Adjustment with ' / "  
)
Press O or Q to parallelize the  
upper and lower sides of the  
projected image.  
Horizontal Keystone Correction  
(Adjustment with \ / |  
)
Press KEYSTONE to set the  
position.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
SPHERE  
ROn-screen display  
Press KEYSTONE.  
• The KEYSTONE MODE list appears. (See  
page 31.)  
1
2
3
SPHERE  
END  
TESTPATTERN  
0
ADJUST  
RESET  
Press P/R to select “SPHERE”,  
and then press ENTER.  
Concave Distortion Correction  
(Adjustment with P/Q)  
Press P/R/O/Q to adjust the  
sphere correction.  
Convex Distortion Correction  
(Adjustment with R/O)  
Press KEYSTONE to set the  
position.  
4
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching the Input Mode  
Select the appropriate input mode for the  
connected equipment.  
HDMI 1/2, COMPONENT  
and COMPUTER buttons  
Press HDMI 1/2, COMPONENT or  
COMPUTER on the remote control to  
select the input mode.  
When you select the input mode with  
INPUT R/P on the projector:  
• When R/P is pressed, the INPUT list  
appears. While the INPUT list is  
displayed, follow the procedure below to  
switch the input mode.  
INPUT list  
INPUT  
HDMI1  
HDMI2  
COMPUTER  
COMPONENT  
– Press R/P to select the desired input  
mode and then press ENTER.  
• If ENTER is not pressed, the projector  
switches to the selected input mode in a  
few seconds.  
Note  
• When you switch the input mode, the image  
as shown below will be displayed in the upper  
right corner of the screen. (You can confirm  
the selected input mode and information on  
the input signal.)  
HDMI1  
YPbPr  
1080P  
• When  
• If  
is displayed, “3D” is set to “On”.  
is displayed, it means that a 3D image  
signal that can be automatically detected is  
being input.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Resize Mode  
This function allows you to modify or customize the Resize mode to enhance the input  
image. Depending on the input signal, you can choose a desired image.  
Press RESIZE on the remote control or on the  
projector.  
• See page 51 for setting on menu screen.  
RESIZE  
button  
RESIZE  
NORMAL  
Output screen image  
The image is displayed with the original aspect ratio.  
16:9  
An image compressed from a 16:9 aspect ratio to a 4:3 aspect ratio is restored to a  
16:9 aspect ratio and displayed at full-screen.  
CINEMA ZOOM  
ZOOM 14:9  
A CinemaScope image or an image with a 16:9 aspect ratio is displayed at full-screen.  
An image with a 14:9 aspect ratio and letterboxing is enlarged while maintaining the  
original aspect ratio.  
SMART ZOOM  
NATIVE  
An image with a 4:3 aspect ratio is slightly enlarged.  
The image is displayed according to the original input signal.  
About Copyrights  
• When using the Resize function to select an image size with a different aspect ratio to a TV  
program or video image, the image will look different from its original appearance. Keep this  
in mind while choosing an image size.  
• The use of the Resize, Keystone Correction, Overscan or Anamorphic function to compress  
or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an  
infringement of copyright protected by law for copyright holders. Please use caution.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating with the Remote Control  
Selecting the Picture Mode  
CONTRAST,  
BRIGHTNESS, COLOR  
and TINT buttons  
You can select the appropriate Picture  
mode for the projected image, such as  
movie or video game.  
Press PICTURE MODE to  
display the Picture Mode list.  
1
IRIS 1/2 buttons  
PICTURE MODE button  
Press P/R to select the  
2
appropriate picture mode, and  
MENU HIDE button  
then press ENTER.  
Picture Mode list  
AUTO SYNC button  
ECO+QUIET button  
Picture Mode  
Standard  
Movie1  
Movie2  
Monochrome  
Anime  
Sports  
Stage  
Dynamic  
User1  
Adjusting the Image  
You can adjust the contrast, brightness,  
color and tint.  
User2  
Game  
Press image adjustment buttons.  
Button  
+ button  
- button  
CONTRAST For more contrast. For less contrast.  
BRIGHTNESS For more brightness. For less brightness.  
Note  
COLOR  
For more color  
intensity.  
For less color  
intensity.  
• You can also select a picture mode when  
projecting images in 3D mode.  
• See page 44 for details on the Picture mode.  
TINT  
For making skin  
tones greenish.  
For making skin  
tones purplish.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating with the Remote Control (Continued)  
Switching the Iris Setting  
Hiding the Menu Temporarily  
(Menu Hide)  
This function controls the quantity of the  
projected light and the contrast of the  
image.  
When the menu screen is displayed, you  
can temporarily hide the menu screen by  
pressing and holding MENU HIDE on the  
remote control. This is useful when, for  
example, checking the video adjustment  
information.  
Press IRIS 1 or 2.  
• Each time the button is pressed while the display  
is on, the mode changes in the following order:  
IRIS 1 High Brightness  
IRIS 2  
High Contrast  
On  
Off  
Note  
Switching the Eco+Quiet Mode  
• For details, see page 45.  
Press ECO+QUIET to switch the  
Eco+Quiet mode between on and off.  
• When the Eco+Quiet Mode is set to “On”, the  
sound of the cooling fan will turn down, the power  
consumption will decrease, and the lamp life will  
extend.  
Auto Sync  
(Auto Sync Adjustment)  
Note  
Auto Sync function works when detecting  
input signal after the projector turns on.  
• Refer to “Eco+Quiet” on page 45 for details.  
Press AUTO SYNC to manually adjust  
with Auto Sync function.  
Note  
• When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual  
adjustments. (See page 49.)  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
The following shows the items that can be set in the projector.  
“Picture” menu  
Main menu  
Sub menu  
in 2D mode  
Picture  
Picture Mode  
Standard  
Movie1, 2  
Monochrome  
Anime  
Sports  
Stage  
Dynamic  
User1, 2  
Game  
Page 44  
Page 44  
Contrast  
Bright  
Color  
Tint  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
in 3D mode  
Sharp  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-2 +2  
Standard(3D)  
Movie1, 2(3D)  
Monochrome(3D)  
Anime(3D)  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
Sports(3D)  
Stage(3D)  
Dynamic(3D)  
User1, 2(3D)  
Game(3D)  
Page 45  
IRIS1(Manual)  
High Brightness  
High Contrast  
Page 45  
Gamma  
IRIS2(Auto) [On/Off]  
-2 +2  
Page 45  
Custom Gamma [On/Off]  
Page 45  
Eco+Quiet [On/Off]  
Page 46  
C.M.S.1  
Page 45  
Advanced  
Select Color  
Hue  
Page 45  
C.M.S.2  
Reset  
Saturation  
Value  
Page 46  
Page 48  
Effect  
C.M.S.1 (or C.M.S.2)  
[On/Off]  
Reset  
Return  
Bright Boost [On/Off]  
Page 48  
Film Mode  
Auto  
Off  
Page 48  
Color Enhance  
0
Page 48  
Detail Enhance  
+5  
-30 +30  
Page 48  
DNR  
Off  
Level1  
Level2  
Level3  
Page 48  
MNR  
Page 48  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items (Continued)  
“Signal adjustment (SIG-ADJ)” menu  
“Screen adjustment (SCR-ADJ)” menu  
Main menu  
SCR-ADJ  
Sub menu  
Main menu  
SIG-ADJ  
Sub menu  
Resize  
Normal  
Clock  
Phase  
H-Pos  
V-Pos  
Reset  
-150 +150  
-30 +30  
-150 +150  
-60 +60  
16:9  
Page 51  
Page 51  
CinemaZoom  
Zoom14:9  
SmartZoom  
Native  
Page 49  
-30 +30  
V-Image Shift  
Page 51  
Trigger  
Page 49  
Off  
Screen  
Anamorphic  
Resolution  
Page 51  
Page 49  
Auto Sync [On/Off]  
Anamorphic  
Off  
2.35:1  
16:9  
Page 51  
Overscan [On/Off]  
Page 52  
Page 49  
Signal Type  
Auto  
RGB  
YPbPr  
Page 50  
Video Setup  
Black Mask  
0
+5  
0IRE  
7.5IRE  
Page 52  
Page 50  
Dynamic Range  
Page 50  
Signal Info  
CBNR [On/Off]  
Page 52  
OSD Display [On/Off]  
Page 52  
OSD Brightness  
Page 52  
Auto  
Standard  
Enhanced  
Page 50  
Standard  
Level1  
Level2  
Background  
Logo  
Blue  
None  
Page 52  
Menu Position  
Center  
UpperRight  
LowerRight  
UpperLeft  
LowerLeft  
Page 53  
PRJ Mode  
Front  
Ceiling + Front  
Rear  
Ceiling + Rear  
Page 53  
English  
polski  
Language  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Magyar  
Türkçe  
Page 53  
Svenska  
Português  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“Network” menu  
“Projector adjustment (PRJ-ADJ)” menu  
Main menu  
Sub menu  
Main menu  
PRJ-ADJ  
Sub menu  
Password  
[Enable/Disable]  
Auto Power Off [On/Off]  
Page 54  
Network  
Page 54  
Page 58  
Page 58  
DHCP Client [On/Off]  
Off  
No Operation off  
1Hour  
Page 54  
2Hours  
4Hours  
6Hours  
Page 59  
TCP/IP  
IP Address  
Subnet Mask  
Gateway  
Economy Mode [On/Off]  
Page 59  
Reset Network Setting  
Page 54  
One Touch Play [On/Off]  
System Standby [On/Off]  
Input Name  
Page 59  
Restart Network  
Page 59  
IP Address  
Page 55  
Page 60  
LED [On/Off]  
MAC Address  
Page 56  
Demo Mode [On/Off]  
Page 56  
Fan Mode  
Page 60  
Projector  
Page 60  
Normal  
High  
Page 56  
Memory Menu  
Page 56  
All Reset  
Page 57  
Lamp Timer (Life)  
Page 57  
“3D MENU”  
Main menu  
Sub menu  
3D [On/Off]  
3D MENU  
Load Memory  
Memory1  
Memory2  
Page 56  
Save Memory  
Page 70  
Page 70  
3D Format  
Auto  
Side By Side  
Top And Bottom  
Page 56  
Memory Name  
Page 70  
3D Depth Adjust  
–15 +15  
Page 56  
Clear Memory  
Page 70  
3D Auto Change  
Yes  
No  
Page 57  
Page 70  
Memory Lock [On/Off]  
Viewing Time Info  
Yes  
No  
Page 57  
Return  
Page 70  
Invert  
Page 70  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen  
RETURN button  
• Press RETURN to return to the  
previous screen when the menu is  
displayed.  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
MENU button  
MENU button  
Adjustment buttons  
(P/R/O/Q)  
ENTER button  
RETURN button  
• Press RETURN to return  
to the previous screen  
when the menu is  
displayed.  
Menu Selections (Adjustments)  
Example: Adjusting “Bright”.  
• This operation can also be performed by using the buttons on the projector.  
Press MENU.  
Example: “Picture” screen menu  
Menu item  
1
2
• The “Picture” menu screen for the selected  
input mode is displayed.  
Picture  
Picture Mode  
Contrast  
Bright  
SIG  
SCR  
PRJ  
Standard  
Net.  
Press Q or O and select  
“Picture” to adjust.  
0
0
0
0
0
0
0
0
0
Color  
Tint  
Sharp  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
IRIS1 (Manual)  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Reset  
High Brightness  
On  
Off  
SEL./ADJ.  
RETURN  
ENTER  
END  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture  
Picture Mode  
Contrast  
Bright  
Color  
Tint  
SIG  
SCR  
PRJ  
Standard  
Net.  
Press P or R and select “Bright”  
3
to adjust.  
0
0
0
0
0
0
0
0
0
• The selected item is highlighted.  
Sharp  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
IRIS1 (Manual)  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Reset  
High Brightness  
On  
Off  
SEL./ADJ.  
RETURN  
ENTER  
END  
Items to be adjusted  
Pict.  
Clock  
Phase  
H-Pos  
V-Pos  
SCR  
PRJ  
Net.  
SIG-ADJ  
0
To adjust the projected  
image while watching it  
0
0
0
Press ENTER.  
Reset  
• The selected item (e.g. “Bright”) is  
displayed by itself at the bottom of the  
screen.  
Press ENTER.  
• When pressing P or R, the following item  
(“Color” after “Bright”) will be displayed.  
The item displayed by itself  
Bright  
0
Note  
• Press ENTER again to return to the  
previous screen.  
Picture  
Picture Mode  
Contrast  
Bright  
Color  
Tint  
SIG  
SCR  
PRJ  
Standard  
Net.  
Press O or Q to adjust the item  
4
5
selected.  
0
1 5  
0
0
0
0
0
0
0
• The adjustment is stored.  
Sharp  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
IRIS1 (Manual)  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Reset  
High Brightness  
On  
Off  
Press MENU.  
• The menu screen will disappear.  
SEL./ADJ.  
RETURN  
ENTER  
END  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu)  
Menu operation n Page 42  
Picture  
Picture Mode  
Contrast  
Bright  
Color  
Tint  
SIG  
SCR  
PRJ  
Standard  
Net.  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Gamma  
Custom Gamma  
0
0
0
0
0
0
0
0
0
0
Off  
Sharp  
Red Gain  
Green Gain  
Blue Gain  
CLR Temp  
IRIS1 (Manual)  
IRIS2 (Auto)  
Eco+Quiet  
Advanced  
Reset  
C.M.S.1  
C.M.S.2  
On  
Off  
Off  
Bright Boost  
Film Mode  
Color Enhance  
Detail Enhance  
DNR  
Auto  
High Brightness  
0
0
On  
Off  
Off  
Off  
MNR  
Reset  
SEL./ADJ.  
RETURN  
ENTER  
END  
SEL./ADJ.  
RETURN  
ENTER  
END  
Selecting the Picture Mode  
This function allows you to select the picture mode that best suits the room brightness and the  
type of image being projected.  
Selectable items  
Standard  
Description  
For standard image.  
Movie1  
Movie2  
Monochrome  
Anime  
Sports  
Stage  
For viewing movies with a lot of bright scenes.  
For viewing movies with a lot of dark scenes.  
For viewing black-and-white movies.  
For viewing anime or animated movies.  
For viewing sports and other images with fast-moving subjects.  
For viewing live performances.  
Dynamic  
User1, 2  
Game  
A vivid image is obtained.  
For customizing the picture mode settings as desired.  
Use this when the audio and image are not synched or when you want to create a  
sharper image.  
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are  
retained in memory.  
Note  
• You can also select a picture mode when projecting images in 3D mode.  
You can also press PICTURE MODE on the remote control to select the picture mode. (See page 37.)  
• The default settings are subject to change without notice.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
Adjusting the Image  
Eco+Quiet  
2
4
Selectable  
items  
Adjustment  
items  
Brightness and Power consumption  
? button  
_ button  
On  
Off  
Approx. 70%  
100%  
Contrast  
Bright  
For less contrast.  
For less brightness. For more brightness.  
For more contrast.  
Color  
For less color  
intensity.  
For more color  
intensity.  
Tint  
For making skin  
tones purplish.  
For making skin  
tones greenish.  
Note  
• When “Eco+Quiet” is set to “On”, the power  
consumption will decrease and the lamp life  
will extend. (Projection brightness decreases  
approximately 30%.)  
Sharp  
Red Gain  
For less sharpness. For more sharpness.  
For making images For making images  
less reddish.  
more reddish.  
Green Gain For making images For making images  
less greenish. more greenish.  
Blue Gain  
You can also use ECO+QUIET on the remote control  
to switch the Eco+Quiet mode. (See page 38.)  
For making images For making images  
less bluish.  
more bluish.  
CLR Temp For making images  
slightly more reddish  
For making images  
slightly more bluish  
Using the Advanced  
“Advanced” allows you to make even finer  
adjustments to the image so that it appears just  
the way you want it to.  
To display the Advanced menu, select  
“Advanced” and press ENTER.  
5
(slightly warmer colors). (slightly cooler colors).  
Note  
You can also use CONTRAST,  
BRIGHTNESS, COLOR or TINT on the remote  
cntorol to adjust each item. (See page 37.)  
Note  
• When the “Advanced” settings are displayed,  
select “Advanced” again and press ENTER to  
return to the “Picture” menu.  
Switching the Iris Setting  
This function controls the quantity of the  
projected light and the contrast of the image.  
IRIS1 (Manual)  
Correcting Gradation of  
Selectable  
Description  
items  
Video (Gamma Correction)  
When the darker areas of the image become  
difficult to see because of the image or the  
projection environment, you can correct the  
gamma setting to make the image brighter and  
easier to see.  
High  
This mode gives priority to brightness  
over contrast.  
Brightness  
High  
Contrast  
This mode gives priority to contrast  
over brightness.  
IRIS2 (Auto)  
This automatically selects the optimal contrast  
to match the image.  
Selectable  
Description  
items  
+2  
Provides a brighter gradation.  
+1  
Selectable  
Description  
items  
0
Standard setting  
On  
This mode gives priority to contrast  
with the use of auto adjustment.  
–1  
–2  
Provides a darker gradation.  
Off  
This mode gives priority to brightness  
without the use of auto adjustment.  
Note  
• You can also use IRIS 1/2 on the remote  
control to change the Iris. (See page 38.)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu) (Continued)  
Menu operation n Page 42  
Press ENTER to display the  
Custom Gamma  
7
5
6
confirmation screen. Use P/R to  
The Custom Gamma function can be used  
when “Picture Mode” is set to “User1” or  
“User2”.  
You can adjust the gamma curve and save  
your custom setting. Adjust it to suit the  
picture brightness.  
select “Save” and press ENTER.  
To complete the Custom Gamma  
adjustment, select “Return” and  
press ENTER.  
Press P/R to select “Custom  
1
Gamma” on the gamma  
apdrejussstQme.nt screen, and then  
Adjusting the Colors  
Custom Gamma  
You can select the color of the projected  
image to correct and then adjust it to the  
desired color by setting “Hue”, “Saturation”,  
“Value”, and “Effect”.  
Custom Gamma  
Off  
Custom Gamma Edit  
Reset  
Return  
Note  
• Before performing this adjustment, prepare  
the image to be adjusted.  
• You can perform this adjustment easier in the  
still image than in the moving image.  
SEL./ADJ.  
RETURN  
ENTER  
END  
Select “C.M.S.1” or “C.M.S.2”  
1
(C.M.S.: Color Management  
System) in the “Advanced” menu,  
and press Q.  
Press P/R to select “On”.  
2
3
• If there is no data for the stored corrected  
color, the color selection screen and the  
picker is displayed. (Go to step 2.)  
Press R to select “Custom  
Gamma Edit”, and then press  
ENTER.  
Adjust the curve to adjust the  
image brightness.  
4
Picker  
• Press O/Q to adjust the white level. Select  
from 10 levels, from 5% to 80%.  
• Press P/R to adjust the optical output  
value. Select a value from 0 to 100.  
Custom Gamma  
Custom Gamma  
On  
Custom Gamma Edit  
Reset  
Return  
Output:  
XX%  
Input:  
XX%  
SEL./ADJ.  
RETURN  
ENTER  
END  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
C.M.S. color adjustment screen:  
• If there is data for the stored corrected  
color, the C.M.S. color adjustment screen  
is displayed. (Go to step 3.)  
Selectable  
items  
Description  
Select  
Color  
Hue  
Starts over the selection of the  
color to be corrected.  
Sets the hue of the main colors.  
C.M.S.1  
Select Color  
Hue  
Saturation  
Value  
Effect  
C.M.S.1  
Reset  
Return  
0
0
0
0
On  
Saturation Sets the saturation of the main  
colors.  
Value  
Sets the value of the main colors.  
SEL./ADJ.  
RETURN  
ENTER  
END  
Effect*1  
Specifies the range of color  
correction.  
Checks the appearance of the  
projected image after above  
correction.  
C.M.S.1*2  
(or  
C.M.S.2)  
Reset  
Sets “Hue”, “Saturation”,  
“Value”, and “Effect” to their  
default values.  
Completes the correction  
and closes the C.M.S. color  
adjustment screen.  
Use the picker and select the  
color of the projected image to  
correct. The picker can be  
operated by adjustment buttons  
(P/R/O/Q) on the remote control.  
2
Return  
*1 To specify the range of color correction,  
select “Effect” and press O or Q.  
O button  
Specifies smaller range.  
Specifies larger range.  
Picker  
Q button  
*2 To check the appearance of the  
projected image, select “C.M.S.1” (or  
“C.M.S.2”) and set to “On” or “Off”.  
On  
The appearance of the projected  
image after above color  
adjustment reflected can be  
checked.  
• By continuing to press the adjustment  
buttons (P/R/O/Q), the picker moves  
rapidly.  
Off  
The appearance of the projected  
image in former color adjustment  
can be checked.  
After selecting the color of the projected  
image to correct, press ENTER. The  
C.M.S. color adjustment screen is  
displayed. (Go to step 3.)  
To complete the C.M.S. color  
adjustment, select “Return” and  
press ENTER.  
4
Set or adjust each item in the  
C.M.S. color adjustment screen.  
3
Note  
C.M.S.1  
Select Color  
Hue  
Saturation  
Value  
Effect  
C.M.S.1  
Reset  
Return  
• The C.M.S. color adjustment can be made to  
one color each in “C.M.S.1” and “C.M.S.2”.  
0
0
0
0
On  
SEL./ADJ.  
RETURN  
ENTER  
END  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu) (Continued)  
Menu operation n Page 42  
Adjusting the Bright Boost  
9
Note  
Bright Boost uses Texas Instruments’ Bright  
Boost technology. The image becomes  
brighter while the color reproduction is kept at  
a high level.  
Set “DNR” to “Off” in the following cases:  
- When the image is blurry.  
- When the contours and colors of moving  
images drag.  
- When TV broadcasts with weak signals are  
projected.  
Selectable  
Description  
items  
This function is available for the following  
signals.  
On  
Off  
The Bright Boost function is activated.  
The Bright Boost function is not activated.  
- 480  
I
/480P  
- 576I/576P  
Selecting the Film Mode  
This function provides high-quality playback  
of images originally projected at 24 fps, such  
as movies on DVDs.  
0
Mosquito Noise Reduction (MNR)  
The so-called Mosquito Noise (flickering) can  
be reduced.  
U
Selectable  
Description  
items  
Selectable  
Description  
items  
Auto  
Off  
Films are detected automatically.  
Films are not detected.  
Off  
MNR does not function.  
Level 1  
Level 2  
Level 3  
Sets the MNR level for viewing a clearer  
picture.  
Setting Color Enhancement  
This function makes the projected images  
clearer and crisper.  
Note  
Set “MNR” to “Off” in the following cases:  
- When the image is blurry.  
- When the contours and colors of moving  
images drag.  
- When TV broadcasts with weak signals are  
projected.  
This function is available for the following  
signals.  
Provides less color enhancement.  
Provides more color enhancement.  
? button  
_ button  
Setting Detail Enhancement  
Z
This function enhances the details in images  
and, thereby, creates a greater sense of depth.  
Provides less detail enhancement.  
Provides more detail enhancement.  
? button  
- 480  
I
/480P  
- 576I/576P  
_ button  
Reducing Image Noise (DNR)  
Video digital noise reduction (DNR) provides  
high quality images with minimal dot crawl  
and cross color noise.  
H
Resetting All Adjustment Items  
To reset all adjustment items to the default  
W
settings, select “Reset” and press ENTER.  
Selectable  
Description  
items  
Off  
The DNR function is not activated.  
Level 1  
Level 2  
Level 3  
Sets the DNR level for viewing a clearer  
picture.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Image Adjustment (“SIG-ADJ” Menu)  
Menu operation n Page 42  
Pict.  
Clock  
Phase  
H-Pos  
V-Pos  
SCR  
PRJ  
Net.  
SIG-ADJ  
Setting the Resolution  
ꢁꢅ  
0
0
0
0
Ordinarily, the type of input signal is detected  
and the correct resolution mode is automatically  
selected. However, for some signals, the optimal  
resolution mode in “Resolution” in the “SIG-  
ADJ” menu may need to be selected to match  
the computer display mode.  
Reset  
Resolution  
Auto Sync  
Signal Type  
Video Setup  
On  
Auto  
0IRE  
Auto  
*
Dynamic Range  
Note  
Signal Info : 1080P  
H : XX.X kHz/  
Avoid displaying computer patterns which repeat  
every other line (horizontal stripes). (Flickering  
may occur, making the image hard to see.)  
Information on the currently selected input  
signal can be confirmed in item 7 on page 50.  
V : XX.X Hz  
SEL./ADJ.  
RETURN  
ENTER  
END  
* Displayed when the input mode is HDMI input.  
Adjusting the Computer Image  
Use the SIG-ADJ function in case of  
irregularities such as vertical stripes or  
flickering in portions of the screen.  
ꢀꢅ  
Auto Sync (Auto Sync Adjustment)  
ꢂꢅ  
Selectable  
items  
Description  
On  
Auto Sync adjustment will occur when  
the projector is turned on or when the  
input signals are switched, when con-  
nected to a computer.  
Selectable  
Description  
items  
Clock  
Phase  
Adjusts vertical noise.  
Off  
Auto Sync adjustment is not  
automatically performed.  
Adjusts horizontal noise (similar to  
tracking on your VCR).  
H-Pos  
V-Pos  
Centers the on-screen image by  
moving it to the left or right.  
Note  
Centers the on-screen image by  
moving it up or down.  
Auto Sync adjustment is also performed by  
pressing AUTO SYNC on the remote control.  
• When setting “Auto Sync” to “Off”, and if  
AUTO SYNC is pressed, Auto Sync will be  
executed in “On” mode. If the button is  
pressed again within one minute, Auto Sync  
will be executed in “On” mode.  
• The Auto Sync adjustment may take some  
time to complete, depending on the image of  
the computer connected to the projector.  
Note  
• You can automatically adjust the computer  
image by setting “Auto Sync” in the “SIG-ADJ”  
menu to “On”, or pressing AUTO SYNC on  
the remote control.  
• Depending on the type of input signal, the  
adjustment range for each setting may vary or  
the adjustment may not be available at all.  
• To reset all adjustment items, select “Reset”  
When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual  
adjustments.  
and press ENTER  
.
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Image Adjustment (“SIG-ADJ” Menu)  
(Continued)  
Menu operation n Page 42  
Signal Type Setting  
ꢃꢅ  
When using an input mode of HDMI1, HDMI2, or  
COMPUTER, set the signal type to the  
corresponding input signal type (RGB or YPbPr).  
Selectable  
Description  
items  
Auto  
Automatically selects the appropriate  
input signal between RGB and YPbPr.  
RGB  
Set when RGB signals are received.  
Set when YPbPr signals are received.  
YPbPr  
Setting the Video Setup  
5
Selectable  
items  
Description  
0 IRE  
Sets the black level to 0 IRE.  
Sets the black level to 7.5 IRE.  
7.5 IRE  
Note  
• This function is available for the following  
signal.  
- 480I  
Adjusting the Dynamic Range  
6
An optimum picture may not be displayed if an  
HDMI-capable device’s output signal type and  
the projector’s input signal type do not match.  
If this should occur, switch “Dynamic Range”.  
Selectable  
Description  
items  
Auto  
In most circumstances, “Auto” should  
be selected.  
Standard  
Enhanced  
When the black levels of the image  
show banding or appear faded, select  
the item that results in the best picture  
quality.  
Signal Info  
7
Input signal information is displayed.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image (“SCR-ADJ” Menu)  
Menu operation n Page 42  
Pict.  
SCR-ADJ  
0
PRJ  
Normal  
Net.  
SIG  
Trigger  
3
Resize  
V-Image Shift  
Off  
Off  
On  
Trigger  
Anamorphic  
Overscan  
Black Mask  
CBNR  
OSD Display  
OSD Brightness  
Background  
Menu Position  
PRJ Mode  
Language  
This function allows you to set whether to  
output a control signal (12V DC) that is output  
from the trigger terminal to a trigger-  
0
Off  
On  
Standard  
Logo  
Upper Left  
Front  
supported screen or anamorphic lens.  
Selectable  
Description  
items  
Screen  
A control signal (12V) is output to a  
trigger-supported screen while linked  
with the power of the main unit. The  
screen extends and retracts automati-  
cally when the power of the projector is  
turned on and off.  
English  
SEL./ADJ.  
RETURN  
ENTER  
END  
Anamorphic A control signal (12V) is output when  
the Anamorphic function is set to  
"2.35:1" or "16:9".  
Setting the Resize Mode  
1
Off  
The Trigger function is not activated. (A  
control signal (12V) is not output.)  
Note  
• For details of the Resize mode, see page 36.  
• You can also press RESIZE on the remote  
control to set the resize mode. (See page 36.)  
Anamorphic  
4
This function adjusts the vertical and  
horizontal directions of the image when  
projected using an anamorphic lens.  
Adjusting the Image Position  
2
You can move the projected image vertically.  
Selectable  
Description  
items  
? button  
_ button  
2.35:1  
Stretches a 2.35:1 image in the vertical  
direction of the panel resolution.  
Downward  
Upward  
16:9  
Select this when viewing images other  
than 2.35:1 while using an anamorphic  
lens.This compresses a 16:9 image  
in the horizontal direction while leav-  
ing the height of the panel resolution  
unchanged.  
? button  
_ button  
Off  
The input image is projected as is.  
(Black bands are displayed on the top,  
bottom, left and right.)  
Note  
• RESIZE does not function when “Anamorphic”  
is set to “2.35:1” or “16:9”.  
Note  
• The adjustable range of the image shift may  
vary depending on:  
- the Resize mode  
- the Picture mode  
- the input signal resolution  
- the input 3D signal type  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image (“SCR-ADJ” Menu)  
(Continue)  
Menu operation n Page 42  
Adjusting the Overscan  
CBNR  
5
7
This function allows you to adjust the  
Overscan area (display area).  
This function reduces the color break noise.  
Selectable  
Description  
items  
Selectable  
Description  
items  
On  
Off  
The CBNR function is activated.  
The input area is displayed without  
screen edges.  
The CBNR function is not activated.  
On  
Off  
The whole input area is displayed.  
Note  
When “3D” is set to “On”, the CBNR function is  
Note  
disabled.  
When “CBNR” is set to “On”, the brightness is  
reduced.  
You can adjust the Overscan area for the  
following input signals and the RESIZE function.  
Input signal:  
- 480  
- 540P  
- 576 /576P  
I
/480P  
Setting On-screen Display  
8
I
- 720P  
Selectable  
items  
- 1035  
I
Description  
- 1080  
I
/1080P  
RESIZE function:  
On  
Off  
All on-screen displays are displayed.  
- NORMAL  
INPUT/AUTO SYNC/RESIZE/  
CONTRAST/BRIGHTNESS/COLOR/  
TINT/ECO+QUIET/3D ON/OFF (3D/2D  
mode change) message are not  
displayed.  
- 16:9  
- CINEMA ZOOM  
- ZOOM 14:9  
• If the display area ratio is set too large, noise  
may appear at the screen edges. If this  
happens, set the display area ratio to a  
smaller value.  
• Also read “About Copyrights” on page 36.  
Setting the Brightness of  
the Menu Screen  
Black Mask  
6
Sets the brightness of the menu screen.  
Selectable  
Description  
items  
This function allows you to apply a black mask  
around the outside of the image to hide flicker  
on the edges. Select a level from 0 (%) to 5 (%).  
Standard  
Level 1  
Level 2  
Standard brightness  
Darker than the “Standard” brightness  
Darker than the “Level 1” brightness  
Selecting the Background Image  
0
Selectable  
items  
Description  
Logo  
Blue  
SHARP logo screen  
Blue screen  
None  
— (Black screen)  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
Selecting the Menu Screen  
T
Position  
Select “Menu Position” in the “SCR-ADJ” menu  
and the desired position for the menu screen.  
Selectable  
Description  
items  
Center  
Displayed on the center of the image.  
Upper Right Displayed on the upper right of the  
image.  
Lower Right Displayed on the lower right of the  
image.  
Upper Left  
Displayed on the upper left of the  
image.  
Lower Left  
Displayed on the lower left of the  
image.  
Reversing/Inverting  
Projected Images  
Z
This function allows the projector to be used in  
a wider range of projection styles by allowing  
the image to be inverted to suit the projection  
environment (location).  
Selectable  
Description  
items  
Front  
Normal image (Projected from the front  
of the screen)  
Ceiling +  
Front  
Inverted image (Projected from the front  
of the screen with an inverted projector)  
Rear  
Reversed image (Projected from the  
rear of the screen or with a mirror)  
Ceiling +  
Rear  
Reversed and inverted image  
(Projected with a mirror)  
See page 22 for details of Projection (PRJ)  
Mode.  
Selecting the On-screen  
H
Display Language  
The projector can switch the on-screen display  
language among 17 languages.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projector Function (“PRJ-ADJ” Menu)  
Menu operation n Page 42  
Pict.  
SCR  
PRJ-ADJ  
On  
Off  
Off  
Off  
Net.  
SIG  
Setting No Operation Off  
Auto Power Off  
No Operatin Off  
Economy Mode  
One Touch Play  
System Standby  
Input Name  
LED  
Mode  
This function automatically switches the projector  
to Standby mode if there is no operation.  
Off  
Off  
Demo Mode  
Fan Mode  
Memory Menu  
All Reset  
Off  
Normal  
Selectable  
Description  
items  
Off  
The No Operation Off function will be  
disabled.  
1 Hour  
Select the length of time the projec-  
tor will take to automatically enter to  
Standby mode.  
Lamp Timer (Life)  
2 Hours  
4 Hours  
6 Hours  
X
h
XX min  
(
XX% )  
SEL./ADJ.  
RETURN  
ENTER  
END  
Note  
Setting Auto Power Off Mode  
This function automatically switches the  
projector to Standby mode if no signals are  
received for a set period.  
ꢀꢅ  
• When a time is set for the No Operation Off  
function and no operation has been  
performed, 5 minutes before the projector  
enters Standby mode, "Enter STANDBY mode  
in X min." will appear on the screen to indicate  
the remaining minutes.  
Selectable  
Description  
items  
On  
When no input signal is detected for  
more than 15 minutes, the projector will  
automatically enter Standby mode.  
Setting the Power Save  
Mode (Economy Mode)  
Off  
The Auto Power Off function will be  
disabled.  
Economy Mode  
Selectable  
items  
Description  
Note  
On  
Off  
This enables the Economy mode.  
• When the Auto Power Off function is set to  
“On”, 5 minutes before the projector enters  
Standby mode, the message “Enter STANDBY  
mode in X min.” will appear on the screen to  
indicate the remaining minutes.  
You can use the linked functions.  
RS-232C can be used to control the  
projector in Standby mode.  
Note  
• Set this function to “Off” when you want to  
use RS-232C to control the projector from a  
computer.  
• One Touch Play is set to “Off” when the  
Economy mode is set to “On”.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
Setting One Touch Play,  
Note  
System Standby and Input Name  
When a Sharp product equipped with  
Consumer Electronics Control (HDMI CEC) is  
connected to the projector with an HDMI cable,  
you can use the linked function with HDMI CEC  
(“One Touch Play” and “System Standby”).  
• When enabling System Standby, be sure to  
enable the CEC setting on the HDMI-  
compliant Sharp Video Products connected  
to the projector.  
Setting the Input Terminal Names (Input  
Name)  
Set the name of the input terminal (up to 14  
alphanumerical characters).  
Note  
• The CEC function may not work with some  
CEC devices. (When the projector is  
connected to a non-Sharp product, the CEC  
function may not work.)  
Press P/R to select “Input  
1
Name” and then press ENTER.  
Pict.  
SCR  
PRJ-ADJ  
Net.  
SIG  
HDMI1  
Setting the One-Touch Playback Function  
(One Touch Play)  
Input name  
H D M I 1  
One Touch Play turns on the projector and  
selects the input automatically when you turn  
on or begin playback on connected HDMI-  
compliant Sharp Video Products.  
Reset  
Return  
Selectable  
Description  
items  
? or _ button  
Ŧ or Ŷ button  
ENTER button  
Selects a character column.  
Selects a character.  
On  
Off  
This enables One Touch Play.  
This disables One Touch Play.  
Sets the input terminal name.  
Note  
• When enabling One Touch Play, be sure to  
enable the CEC setting on the HDMI-  
compliant Sharp Video Products connected  
to the projector.  
• The Economy mode is set to “Off” when One  
Touch Play is set to “On”.  
Press P/R to select “Return” and  
2
then press ENTER to return to  
the previous screen.  
• To return to the previous setting, select  
“Reset” and then press ENTER.  
• In the following cases, One Touch Play is not  
enabled.  
Note  
• When connecting the projector to a Sharp  
Video Product with an HDMI cable using an  
input mode of HDMI1 or HDMI2 and the linked  
function with HDMI CEC (“One Touch Play” or  
“System Standby”) works normally, the name  
of the connected Sharp Video Product is  
automatically captured.  
Setting the System Standby Function  
(System Standby)  
When you turn off the projector, the HDMI-  
compliant video equipment connected to the  
projector enters Standby mode.  
When the input terminal name has been changed  
by a user, the changed name is displayed.  
Selectable  
Description  
items  
• To return to the default name, select “Reset”  
and press ENTER.  
On  
Off  
This enables System Standby.  
This disables System Standby.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A
djusting the Projector Function (“PRJ-ADJ” Menu)  
(Continued)  
Menu operation n Page 42  
Turning LED Off  
Memory Menu  
5
8
LEDs (indicators) on the projector can be turned You can store the settings of the projector's  
off when they are disturbing the projection.  
lens shift (ZOOM, FOCUS) and others (such as  
INPUT, PICTURE MODE, RESIZE, PRJ Mode,  
V-Image Shift, KEYSTONE and Anamorphic),  
or activate the stored settings.  
The Memory Menu screen can also be  
displayed by pressing MEMORY on the  
remote control.  
Selectable  
Description  
items  
On  
Off  
LEDs are turned on.  
LEDs are turned off while the projector  
is in operation. (LEDs turn on while  
the projector is in the Standby mode,  
warming up or indicating problems.)  
a Load Memory  
To activate the desired settings, select the  
item where the settings are stored.  
Note  
• When Auto Power Off function is set to “Off”,  
“LED” is set to “On” automatically. Be sure to  
set Auto Power Off function to “On” to use  
LED Off function. (See page 54.)  
Note  
• Pressing any button while the projector is in  
the process of activating the “Load Memory”  
function will display messages:  
– “STOP”: stops the activation of the “Load  
Memory” function.  
– “CONTINUE”: allows the projector to the  
already set position.  
Setting the Demo Mode  
Set the Demo Mode to “On” or “Off”.  
– “Return to the initial position.”: let the  
projector go back to the initial position.  
• The confirmation screen of “Load Memory”  
will also be displayed by pressing MEMORY  
1/2 on the remote control. Press MEMORY  
1/2 again to perform the “Load Memory”  
function.  
Selectable  
Description  
items  
On  
Off  
This enables Demo Mode.  
This disables Demo Mode.  
• The memory has a margin of error of  
approximately 2%. Use the remote control to  
make fine adjustments.  
Fan Mode Setting  
This function changes the fan rotation speed.  
Selectable  
Description  
items  
a Save Memory  
Select an item where you want to store the  
setting.  
Normal  
High  
Suitable for normal environments.  
Select this when using the projector at  
altitudes of approximately 4,900 feet  
(1,500 meters) or more.  
Note  
• When “Fan Mode” is set to “High”, the fan  
rotation speeds up, and the fan noise  
becomes louder.  
• When you select an item where some setting  
has been stored, the stored setting will be  
overwritten and erased.  
a Memory Name  
Select the item name you want to change. Use  
O/Q to choose the characters to change, and  
P/R to select the characters to enter.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
a Clear Memory  
Select the item where the settings you want to  
erase are stored. In this case, the memory  
name you have changed returns to the default  
setting.  
Note  
• Selecting “All Clear” erases all the stored  
settings.  
a Memory Lock  
Selectable  
Description  
items  
On  
Off  
Protects the stored memories.  
Does not protect the stored  
memories.  
Returning to the Default  
Settings  
Use “All Reset” to initialize all the adjustments  
you have made to the default settings.  
Note  
The following items cannot be initialized.  
• “SIG-ADJ” menu — Resolution  
• “SCR-ADJ” menu — Language  
• “PRJ-ADJ” menu — Lamp Timer (Life)  
Lamp Timer (Life)  
You can confirm the cumulative lamp usage  
time and the remaining lamp life (percentage).  
Lamp usage condition  
Remaining lamp life  
“Life”  
100%  
5%  
Operated exclusively with Approx.  
“Eco+Quiet” set to “On”  
Approx.  
3,000 hours 150 hours  
Operated exclusively with Approx. Approx.  
2,000 hours 100 hours  
“Eco+Quiet” set to “Off”  
Note  
• It is recommended that the lamp be changed  
when the remaining lamp life becomes 5%.  
• The lamp life may vary depending on the  
usage condition.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector Network Environment  
(“Network” Menu)  
Menu operation n Page 42  
Pict.  
SIG  
SCR  
PRJ  
Network  
a
Changing the Password  
Password  
DHCP Client  
TCP/IP  
Reset Network Setting  
Restart Network  
Disable  
Off  
Select “Password”, then press Q.  
1
• The screen for entering the password  
appears.  
IP Address  
MAC Address  
Projector  
XXX.XXX.XXX.XXX  
XX:XX:XX:XX:XX:XX  
XX-XXXX  
Enter the password in “Old  
Password” using P, R, Q and O,  
then press ENTER.  
2
Enter the password in “New  
Password” using P, R, Q and O,  
then press ENTER.  
3
4
SEL./ADJ.  
RETURN  
ENTER  
END  
Enter the same password again  
in “Reconfirm” using P, R, Q and  
O, then press ENTER.  
Setting a Password  
If you do not want others to change the setting  
for the “Network” menu, set a password.  
1
a
Setting a Password  
Note  
• If you do not need the password protection for  
the “Network” menu settings anymore, press  
ENTER without entering new password in  
steps 3 and 4.  
Select “Password”, then press Q.  
1
• The screen for entering the password  
appears.  
Network  
• To cancel the password settings, press  
RETURN.  
Setting the Password  
Old Password  
New Password  
Reconfirm  
If you forget the password  
If you forget the password, perform the  
following procedure to delete it, then set a  
new password.  
Press P or R to set the first digit  
in “New Password”, then press Q.  
2
On the projector, press  
 
.
Enter the remaining 3 digits, then  
3
4
press ENTER.  
Note  
• To return to the previous digit, press O.  
• You cannot use the buttons on the  
remote control to delete the password.  
Enter the same password in  
“Reconfirm”, then press ENTER.  
• The status for “Password” changes to  
“Enable”.  
Note  
• Once the password is set, you must enter the  
password to change the “Network” menu  
settings.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 42  
Selectable items  
Description  
DHCP Client Setting  
Connect the LAN cable before turning the  
projector on. If not, the DHCP Client function  
does not work.  
2
IP Address  
Factory default setting:  
192.168.150.002  
Enter an IP address appropriate  
for the network.  
Subnet Mask  
Gateway  
Factory default setting:  
255.255.255.000  
Set the subnet mask to the same  
as that of the computer and  
equipment on the network.  
Selectable items  
On  
Description  
Obtains configuration  
parameters for TCP/IP network  
automatically.  
Factory default setting: 000. 000.  
000. 000  
Off  
Sets the TCP/IP manually.  
* When not in use, set to “000.  
000. 000. 000”.  
Select “On” for “DHCP Client”. “Obtaining IP  
Address...” appears, then the menu screen  
appears. Confirm the parameters of IP  
Address, Subnet Mask and Gateway on the  
TCP/IP screen.  
Note  
If the DHCP server is not available, “Could not  
obtain IP Address.” appears.  
In this case, set the TCP/IP manually. (See the  
item 3.)  
• Confirm the existing network’s segment (IP  
address group) to avoid setting an IP address  
that duplicates the IP addresses of other  
network equipment or computers. If  
“192.168.150.002” is not used in a network  
with an IP address of “192.168.150.XXX”, you  
don’t have to change the projector IP address.  
• For details about each setting, consult your  
network administrator.  
TCP/IP Setting  
Set the TCP/IP manually.  
3
Select “Off” for “DHCP Client”,  
1
2
3
then press ENTER.  
Returning to Default  
Settings (Network)  
4
Select “TCP/IP”, then press  
ENTER.  
This function allows you to initialize the  
Network settings you have made in the  
projector.  
Enter “IP Address” using P, R, Q  
and O, then press ENTER.  
Note  
Network  
• If the values for IP Address, Subnet Mask or  
Gateway of the projector have been returned  
to the default settings, the computer cannot  
be connected to the projector depending on  
the computer’s network settings.  
Setting the TCP/IP  
1 9 2 . 1 6 8 . 1 5 0 . 0 0 2  
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0  
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0  
IP Address  
Subnet Mask  
Gateway  
Enter “Subnet Mask” using P, R,  
Restart Network Function  
Restarts the network function.  
Perform this function when the projector  
cannot be controlled via the network.  
4
5
5
Q and O, then press ENTER.  
Enter “Gateway” using P, R, Q  
and O, then press ENTER.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector Network Environment  
(“Network” Menu) (Continued)  
Menu operation n Page 42  
Confirming the  
Projector Information  
6
You can confirm the following items.  
Selectable  
Description  
items  
IP Address  
The IP address of the projector is  
displayed.  
MAC Address The MAC address of the projector is  
displayed.  
Projector  
The projector name is displayed.  
Note  
• For information on how to change the  
projector name, see “SETUP MANUAL”  
contained in the supplied CD-ROM.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing  
CAUTION: Before viewing 3D images, please read this section carefully.  
they show signs of discomfort, immediately  
discontinue use of the 3D Glasses.  
People with a known history of  
You can use special 3D Glasses to watch  
3D-supported images on this projector.  
You can enjoy 3D images by viewing the  
video images through the 3D Glasses  
supplied with the projector or through  
optional 3D glasses sold separately.  
To produce 3D images, liquid crystal  
shutters in the 3D Glasses alternately open  
and close imperceptibly fast to exactly  
match alternating left and right video  
images displayed by the projector.  
Not all consumers can experience and  
enjoy 3D images. Some people suffer from  
stereo blindness which prevents them from  
perceiving the intended depth of 3D  
entertainment. Also, some people who  
watch 3D programming may experience  
initial feelings of motion sickness as they  
adjust to the picture. Others may  
photosensitivity and people with heart  
problems or poor health should not use the  
3D Glasses. This can worsen existing  
health conditions.  
Do not use the 3D Glasses for other  
purposes (such as general eyeglasses,  
sunglasses, or protective goggles).  
Do not use the 3D function or 3D Glasses  
while walking or moving around. This may  
result in injuries due to running into  
objects, tripping, and/or falling.  
When using the 3D Glasses, take care not  
to accidentally strike the screen or other  
people. Viewing 3D images may cause you  
to misjudge the distance to the screen and  
accidentally strike the screen, resulting in  
possible injury.  
experience headaches, eye fatigue or  
continued motion sickness. Like a roller  
coaster, the experience is not for everyone.  
Precautions on installing  
the IR emitter  
Make sure that the bolts and screws are  
securely fastened. Otherwise, the unit may  
fall, resulting in injury or accident.  
Do not drop, disassemble, or modify the  
product, as this may result in damage or  
malfunction.  
Do not install the IR emitter with it directly  
facing the projector, as this may prevent  
the remote control of the projector from  
functioning properly.  
The IR emitter may interfere with other  
infrared communication equipment.  
When installing the IR emitter to a wall or  
ceiling, use screws that suit the material  
and strength of the wall or ceiling.  
Otherwise, it may damage the material of  
the wall or ceiling.  
When using a screw, provide a hole in the  
sponge at the bottom of the stand in  
advance.  
Request your authorized dealer or  
installation service provider to install the IR  
emitter securely while taking the necessary  
safety measures.  
SHARP will not be liable for any accident or  
damage due to improper installation,  
insufficient mounting strength, misuse, or  
natural disasters.  
Precautions on using the  
3D Glasses  
The 3D Glasses are precision equipment.  
Handle them with care.  
Improper use of the 3D Glasses or failure  
to follow these instructions can result in  
eye strain.  
If you experience dizziness, nausea, or  
other discomfort while viewing 3D images,  
immediately discontinue use of the 3D  
Glasses. Using the binocular disparity 3D  
system of this projector with incompatible  
3D broadcasts or software can make  
images appear with a cross talk blur or  
create overlapping images.  
If you are nearsighted or farsighted or have  
astigmatism or a different level of eyesight  
between the left and right eyes, you should  
take the necessary steps, such as wearing  
eyeglasses, to correct your eyesight before  
viewing 3D images. The 3D Glasses can be  
worn over eyeglasses.  
The 3D Glasses are only recommended for  
people ages 5 and older.  
When children are viewing 3D images, be  
sure a parent or guardian is present.  
Monitor children viewing 3D images, and if  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
As you get more comfortable viewing 3D  
Precautions on viewing 3D  
images  
images:  
Operate the “3D Depth Adjust” function to  
adjust the 3D effect. (See page 70.)  
Adjust the projected image to the most  
comfortable viewing size by zooming.  
(Projecting images on the smallest or  
largest screen size possible may eliminate  
the 3D effect and strain your eyes.)  
Use the Invert function to properly set the  
video for your left and right eyes. (For  
details on using “Invert”, see page 70.)  
A picture simultaneously projected from  
more than two projectors may not appear  
When viewing 3D images continuously, be  
sure to take a break periodically to prevent  
eye strain.  
Take regular breaks, at least 5 to 15  
minutes after every 30 to 60 minutes of 3D  
viewing.  
* Based on the guidelines issued by the 3D  
Consortium revised December 10, 2008.  
View 3D images at the appropriate  
distance from the screen. The  
recommended distance is three times the  
effective height of the picture.  
Examples of recommended distances  
100-inch 16:9 picture: Approx. 12.3 ft (3.8 m)  
Viewing should not be done closer than the  
recommended distance.  
3D.  
Info  
• The projected image may become dark when  
using the 3D projection function (with “3D” set to  
“On”).  
• When “3D” is set to “On”, the following functions  
may not work fully or may not be available at all.  
– GEOMETRIC ADJUSTMENT/H&V KEYSTONE/  
SPHERE  
Refer to page 21 for details on the diagonal  
size and height of the picture.  
Maintain an appropriate distance from the  
screen. Viewing from too close a distance  
can strain your eyes. If you experience eye  
strain, immediately discontinue viewing.  
If you experience any of the following  
symptoms during viewing:  
– V-Image Shift  
– CBNR  
• If the power of your left and right eyes greatly  
differs and you primarily use one eye for viewing  
the images, the images will not appear in 3D. In  
addition, images may be difficult to view in 3D or  
images may not be able to be viewed in 3D  
depending on the individual or the content being  
displayed. The 3D effect varies with the individual.  
– nausea  
– queasiness/dizziness  
– headache  
– blurry vision or double vision that lasts  
longer than few seconds  
Do not engage in any potentially hazardous  
activity (for example, driving a vehicle) until  
your symptoms have completely gone  
away.  
If symptoms persist, discontinue use and  
do not resume 3D viewing without  
discussing your symptoms with a  
physician.  
Be careful of your surroundings when  
viewing 3D images. When you view 3D  
images, objects may appear at a distance  
closer or farther than the actual screen.  
This may cause you to misjudge the  
distance to the screen and possibly result  
in injury if you accidentally hit the screen or  
surrounding objects.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
The following people should limit stereoscopic 3D viewing:  
– Children under 6 years of age (to protect the eye growth process)  
– People with a history of photosensitivity  
– People with heart disease  
– People in poor health  
– People who are sleep deprived  
– People who are physically tired  
– People under the influence of drugs or alcohol  
Epilepsy  
A small percentage of the population may experience epileptic seizures when viewing  
certain types of images that contain flashing patterns of light.  
IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY  
The following people should consult a physician before viewing stereoscopic 3D images.  
– Anyone with a history of epilepsy, or who has a family member with a history of  
epilepsy  
– Children under 6 years of age  
– Anyone who has ever experienced epileptic seizures or sensory disturbances triggered  
by flashing light effects  
SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR  
HISTORY OF EPILEPSY  
Discontinue use if you experience any of the following symptoms while viewing  
stereoscopic 3D images.  
– Involuntary movements, eye or muscle twitching  
– Muscle cramps  
– Nausea, dizziness, or queasiness  
– Convulsions  
– Disorientation, confusion, or loss of awareness of your surroundings  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
Supplied Accessories for the 3D Glasses  
Make sure the following accessories are provided with the 3D Glasses. Two sets of 3D Glasses are provided.  
3D Glasses (×2)  
Pages 65, 66, 68 and 69  
3D Glasses band * (×2)  
Nose pad * (Large ×2, small ×2)  
Page 66  
Page 66  
Cleaning cloth  
(×2)  
Glasses case  
(×2)  
Precision screwdriver  
(Phillips ×2, slotted ×2)  
Page 65  
* Use the 3D Glasses band and nose pad as needed.  
Note  
Please contact your local authority for the correct method of disposal of this product and/or packaging.  
Part Names  
1
2
3
2
LED light  
• Blinks 3 times when the power is turned on.  
• Blinks 2 times when 2D mode is selected.  
• Blinks 3 times when 3D mode is selected.  
• Blinks 6 times when the battery power is low.  
Lights for 2 seconds when the power is turned off.  
4
6
3
4
Service terminal  
This terminal is for service use only.  
Please do not connect any other device to this terminal.  
Infrared receiver  
Receives an infrared signal sent from the IR  
emitter. The 3D Glasses turn off automatically  
after 3 minutes if no signal is received.  
5
Power button  
• Press for at least 2 seconds to turn on and  
off the 3D Glasses.  
• When the 3D Glasses are turned on, pressing  
this button switches between 2D and 3D  
modes. (See page 66.)  
66  
5
6
Nose pad mount  
The dedicated nose pad can be mounted here.  
66  
1
3D Glasses band mount  
The dedicated 3D Glasses band can be  
mounted here.  
Note  
Do not soil or apply stickers or other obstacles to the infrared receiver. Doing so may block signals from  
the IR emitter and prevent the 3D Glasses from working correctly.  
Interference from other infrared communications equipment may prevent you from viewing 3D images correctly.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remove the button cell battery.  
Place the tip of the slotted precision  
screwdriver into the opening between  
the button cell and the socket.  
2
Before Using the 3D Glasses  
Lift up the button cell while taking care  
not to get the screwdriver caught on the  
metal latch.  
Before using the 3D Glasses for the first  
time, remove the insulating sheet  
attached to them.  
2
1
When the battery comes loose  
from the socket, pick it out with  
your fingers.  
3
4
Replacing the Button Cell  
Battery  
The battery has an expected service life  
of approximately 75 hours.  
• When the battery power is low, the LED light  
blinks six times after the power is turned on.  
• When replacing the button cell, use only the  
designated battery type (Maxell branded CR2032  
lithium button battery).  
Hook a new button cell to the metal  
latch and insert it into the socket.  
Take care not to reverse the battery polarity  
(+ and -) when inserting the button cell.  
Loosen the screw used to secure  
the battery cover, and then  
remove the battery cover.  
1
Close the battery cover.  
5
6
Insert the screw to secure the  
battery cover.  
1
2
Note  
• Used batteries should be disposed of in  
accordance with local laws and regulations.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
Using the 3D Glasses  
Attaching the Nose Pad  
Attach either of the supplied nose pads  
as needed (such as when the glasses do  
not fit properly). The glasses come with a  
large and small nose pad.  
Turning On/Off the Power  
Turn on the power of the 3D Glasses.  
• Press the power button for at least 2 seconds.  
• The LED light blinks 3 times.  
Turn off the power on the 3D Glasses.  
• Press the power button for at least 2 seconds.  
• The LED light lights for 2 seconds.  
Note  
• When the battery power is low, the LED light  
blinks 6 times after the power is turned on.  
1
1
2
Switching to 3D and 2D Mode  
When viewing 3D images, you can press  
the power button to switch between 2D  
and 3D modes. This is useful when  
several people are viewing the same 3D  
images with some people wanting to  
watch in 3D and some people wanting to  
watch in 2D.  
Attaching the  
nose pad  
Removing  
the nose pad  
Attaching the 3D Glasses Band  
Attach the supplied 3D Glasses band  
strap as needed (such as when the  
glasses do not fit properly).  
Viewing 2D images  
• When you press the power button twice while  
viewing 3D images, the LED light blinks 2 times  
and the 3D images switch to 2D images.  
Insert the ends of the 3D Glasses into the  
3D Glasses band until they are secure.  
• Pull the cord stopper on the strap to adjust the  
strap length.  
Viewing 3D images  
• When you press the power button twice while  
viewing 2D images, the LED light blinks 3 times  
and the 2D images switch to 3D images.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the IR Emitter to the Projector  
Install the IR emitter unit to the  
stand.  
1
Fasten  
Loosen  
Insert the IR emitter cable to the  
unit.  
2
3
Connect the IR emitter and the  
projector.  
To 3D SYNCHRO terminal  
IR emitter cable  
Position the IR emitter.  
4
3D images are intended to be viewed while  
facing the screen from the front.  
Position the IR emitter so that the 3D  
Glasses can easily receive the infrared  
signals while viewing the screen from the  
front.  
Do not install in a location where objects  
may obstruct the infrared signals between  
the IR emitter and 3D Glasses.  
Adjust the angle of the IR emitter to suit  
your viewing location.  
Note  
When you connect the IR emitter, make sure the power is turned off.  
The supplied IR emitter is exclusively designed for this projector. Do not connect it to other equipment.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
3D MENU button  
Adjustment buttons  
(P/R/O/Q)  
ENTER button  
Note  
3D MENU button  
• The screen may temporarily become black  
when the projector is trying to detect a 3D  
image signal and when switching from 3D to  
2D mode.  
3D ON/OFF button  
Viewing 3D Images  
Receiving a 3D Image Signal That  
Can Be Detected Automatically  
The image signal may contain a 3D  
identification signal. You can enable the  
projector to automatically detect the 3D  
image type by selecting “3D MENU” > “3D  
Auto Change”. (See page 70.)  
When “3D Auto Change” is set to “Yes”  
Turn on the 3D Glasses and place  
them over your eyes.  
• Press the power button for at least 2  
seconds.  
1
2
3
• The 3D image type is detected  
automatically and the appropriate 3D  
image is displayed.  
• The LED light blinks 3 times.  
When “3D Auto Change” is set to “No”  
• The following message is displayed. Press  
3D ON/OFF.  
You can now view 3D images.  
3D picture is detected.  
Press the 3D ON/OFF button on the remote control.  
(Need to wear the 3D glasses to watch 3D picture)  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving a 3D Image Signal That  
Cannot Be Detected Automatically  
Ending 3D Image Viewing  
Press 3D ON/OFF during the 3D  
1
mode.  
Press 3D MENU.  
1
• The 3D MENU screen is displayed.  
Take off the 3D Glasses and turn  
2
Press P/R to select “3D”.  
off the power.  
2
• Press the power button for at least 2  
seconds.  
• The LED light lights for 2 seconds.  
Press O/Q to select “On” or “Off”.  
3
• To view in 3D mode: Select “On”, and then  
go to step 4.  
Note  
• Refer to “Setting the 3D Format Menu” on  
page 71 for supported 3D signals and  
formats.  
• If you select “Off”, the video source will be  
displayed with no conversion.  
• If the input signal switches to 2D, 2D images  
are displayed automatically.  
• 3D mode is canceled automatically in the  
following cases:  
- When the signal is no longer received  
- When the signal type changes  
- When input selection is changed  
- When the power is turned off  
Press P/R to select “3D Format”,  
and then press ENTER.  
4
Press P/R to select a supported  
5
format from the list, and then  
press ENTER.  
Auto  
Side By Side  
Top And Bottom  
• If you select the same system as that of  
the input signal, 3D images are displayed.  
Turn on the 3D Glasses and place  
them over your eyes.  
• Press the power button for at least 2  
seconds.  
6
• The LED light blinks 3 times.  
You can now view 3D images.  
7
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
3D Depth Adjust  
3D Settings (“3D MENU”)  
You can adjust the stereoscopic effect of 3D  
image.  
3D MENU  
For less stereoscopic effect.  
? button  
3D  
On  
Auto  
0
Yes  
Yes  
3D Format  
3D Depth Adjust  
3D Auto Change  
Viewing Time Info  
Invert  
For greater stereoscopic effect.  
_ button  
Note  
• Use this function to get more comfortable 3D  
images.  
• When you use this function, the 3D image will  
look different from its original 3D appearance.  
Keep this in mind while using this function.  
• The use of this function for commercial  
purposes/public displays in a café, hotel, etc.,  
may be an infringement of copyright protected  
by law for copyright holders. Please use  
caution.  
3D  
You can switch between 2D and 3D mode.  
Selectable  
Description  
items  
On  
Off  
Projects 3D images.  
3D Auto Change  
Projects 2D images instead of 3D images.  
This setting can be used to switch to 3D mode  
automatically when a 3D identification signal  
is detected.  
Note  
• When “3D Auto Change” is set to “Yes” and a  
3D signal is detected, “3D” switches to “On”.  
When a 3D identification signal is not detected:  
- If you selected “On”, select the format with  
“3D Format”.  
- If you select “Off”, the video source will be  
displayed with no conversion.  
Selectable  
Description  
items  
Yes  
When a 3D signal is detected, 3D  
mode is selected automatically.  
No  
Auto change is not performed.  
Viewing Time Info  
This displays the elapsed time of 3D image  
viewing.  
3D Format  
You can set the 3D format manually for when  
a 3D signal that cannot be detected  
automatically is received.  
Selectable  
Description  
items  
Selectable  
items  
Description  
Yes  
Displays the elapsed viewing time on  
the screen every hour.  
Auto  
When a 3D identification signal is detect-  
ed, the format is selected automatically.  
No  
Does not display the elapsed viewing  
time.  
Side By Side Select the same format type of the  
received 3D signal.  
Top And Bottom  
Invert  
Pressing ENTER switches between the image  
for the left eye and the image for the right eye,  
so that you can make the settings for more  
natural viewing.  
Note  
Refer to “Setting the 3D Format Menu” on  
page 71 for supported signals and 3D formats.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the 3D Format Menu  
Select the appropriate 3D format for viewing while referring to the table below.  
When “3D” is ON  
When “3D”  
is OFF  
3D Format  
Input signal  
Support  
Top And  
Bottom  
Auto  
Side By Side  
720P  
720P  
50Hz  
60Hz  
Frame  
Packing  
Displays  
image for left correct 3D  
eye  
Displays  
1080I 50Hz  
with 3D  
image  
–*1  
–*1  
identification 1080I 60Hz  
(2D mode)  
(3D mode)  
signal  
1080P 24Hz  
1080P 50Hz  
1080P 60Hz  
720P  
720P  
50Hz  
60Hz  
Displays  
image for left correct 3D  
eye  
(2D mode)  
Displays  
1080I 50Hz  
with 3D  
image  
(3D mode)  
–*1  
–*1  
identification 1080I 60Hz  
signal  
1080P 24Hz  
1080P 50Hz  
1080P 60Hz  
Side By Side  
720P  
720P  
50Hz  
60Hz  
Displays raw Displays raw Displays  
Garbled  
display  
(Incorrect  
setting)  
input signal  
input signal  
correct 3D  
image  
1080I 50Hz  
1080I 60Hz  
1080P 24Hz  
1080P 50Hz  
1080P 60Hz  
without 3D  
idetification  
signal  
*2 (3D mode)  
720P  
720P  
50Hz  
60Hz  
Displays  
Displays  
image for left correct 3D  
1080I 50Hz  
with 3D  
eye  
(2D mode)  
image  
(3D mode)  
identification 1080I 60Hz  
–*1  
–*1  
signal  
1080P 24Hz  
1080P 50Hz  
1080P 60Hz  
Top And  
Bottom  
720P  
720P  
50Hz  
60Hz  
Displays raw Displays raw Garbled  
Displays  
correct 3D  
image  
input signal  
input signal  
display  
(Incorrect  
*2 setting)  
1080I 50Hz  
1080I 60Hz  
1080P 24Hz  
1080P 50Hz  
1080P 60Hz  
without 3D  
idetification  
signal  
(3D mode)  
*1 “3D Format” is set to “Auto” automatically.  
*2 The frame rate is changed.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
Note  
These 3D Glasses can only be used with Sharp 3D-compatible LCD TVs or projectors that use infrared  
control technology.  
3D Glasses lenses  
Do not apply pressure to the lenses of the 3D Glasses. Also, do not drop or bend the 3D Glasses.  
Do not scratch the surface of the lenses of the 3D Glasses with a pointed instrument or other object.  
Doing so may damage the 3D Glasses and reduce the quality of the 3D image.  
Use only the cloth provided with the 3D Glasses to clean the lenses.  
3D Glasses infrared receiver  
Do not allow the infrared receiver to become dirty, and do not attach stickers to or otherwise cover the  
infrared receiver. Doing so may prevent the receiver from operating normally.  
If the 3D Glasses are affected by other infrared data communication equipment, the 3D images may not  
be displayed correctly.  
Caution during viewing  
Do not use devices that emit strong electromagnetic waves (such as cellular phones or wireless  
transceivers) near the 3D Glasses. Doing so may cause the 3D Glasses to malfunction.  
The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them within the  
specified usage temperature range.  
If the 3D Glasses are used in a room with fluorescent lighting (60 Hz), the light within the room may  
appear to flicker. In this case, either darken or turn off the fluorescent lights when using the 3D Glasses.  
Wear the 3D Glasses correctly. 3D images will not be correctly visible if the 3D Glasses are worn upside  
down or back-to-front.  
Other displays (such as computer screens, digital clocks, and calculators) may appear dark and difficult  
to view while wearing the 3D Glasses. Do not wear the 3D Glasses when watching anything other than  
3D images.  
If you lie on your side while watching the screen with 3D Glasses, the picture may look dark or may not  
be visible.  
Be sure to stay within the viewing angle and optimum viewing distance when watching 3D images.  
Otherwise, you may not be able to enjoy the full 3D effect.  
The 3D Glasses may not work properly if there is any other 3D product or electronic devices turned on  
near the glasses or projector. If this occurs, turn off the other 3D product or electronic devices or keep  
the devices as far away as possible from the 3D Glasses.  
Stop using this product in any of the following situations:  
– When images consistently appear doubled while you are wearing the 3D Glasses  
– When you have difficulty perceiving the 3D effect  
If the 3D Glasses are faulty or damaged, stop using them immediately. Continued use of the 3D  
Glasses may cause eye fatigue, headaches and illness.  
If you have any abnormal skin reaction, stop using the 3D Glasses. In very rare instances, such  
reactions may be due to an allergic reaction to the coating or materials used.  
If your nose or temples become red or you experience any pain or itchiness, stop using the 3D Glasses.  
Pressure caused by long periods of use may lead to such reactions and may result in skin irritation.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications – 3D Glasses  
Model  
AN-3DG10  
Lens type  
Power supply  
Battery  
Liquid crystal shutter  
3 V DC  
Lithium button battery (CR2032 × 1)  
Battery life  
Approx. 75 hours of continuous use  
Dimension  
(W x H x D)  
6 13 16 × 1 7/8 × 6 45  
/ /64 inch  
(172.7 × 47.5 × 170.0 mm)  
Weight  
0.2 lbs./65.0 g (including the lithium button battery)  
50°F to 104°F (10°C to 40°C)  
(The 3D Glasses cannot operate fully at extreme high or low temperatures.  
Please use them within the specified usage temperature range.)  
Operating temperature  
The product serial number is displayed on the 3D Glasses as indicated in  
the illustration on the left. The first four digits represent the product color  
and the date of manufacture.  
Example: Silver colored glasses manufactured on August 11, 2010  
Bottom  
S/N : S 0 8 B  
Manufacture number  
Year of  
Color  
Month of  
Day of  
manufacture  
manufacture  
manufacture  
S: Silver  
R: Red  
A: Blue  
0: 2010  
1: 2011  
2: 2012  
1: 1  
2: 2  
3: 3  
1: 1 A : 10  
2: 2  
3: 3  
B : 11  
H : 17  
J : 18  
8:8  
9:9  
N : 22  
P : 23  
A:10  
B:11  
C:12  
W: 30  
X : 31  
*“I”, “O”, “Y”, and “Z” are not used.  
These symbols displayed on the product and the individual carton package of the product  
are symbols about the environment in Japan, China and the EU.  
For Japan only:  
For China only:  
For China only:  
For the EU only:  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying 3D Image Viewing (Continued)  
Specifications – IR Emitter  
Dimension  
[W × H × D]  
5 3/32 × 2 21 64 × 5 23  
/ /32 inch  
(129 × 59 × 137 mm)  
Weight (approx.)  
0.4 lbs. (170 g)  
Dimensions  
90°  
3 19  
5 3  
/
32 (91)  
4 27  
/
64 (112)  
/
32 (129)  
5 3  
/
32 (129)  
     
Effective Distance  
The 3D Glasses can receive infrared  
signals sent from the IR emitter within the  
range indicated in the diagram.  
Operating range (Distance from the IR emitter):  
Approx. 32.8 ft (10.0 m)  
10 m  
Be sure to stay within the operating range when  
watching 3D images. Otherwise, the 3D Glasses  
may not work properly and you may not be able to  
enjoy the 3D images.  
The operating range in the table above is when the  
IR emitter is placed in front of the 3D Glasses. The  
operating range may vary depending on the  
position of the IR emitter and your viewing  
position. (The operating range decreases when  
you view the screen at an angle.)  
30º ( 15º)  
20º ( 10º)  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Cleaning the projector  
Ensure that you have unplugged the power  
cord before cleaning the projector.  
The cabinet as well as the operation panel is  
made of plastic. Avoid using benzene or  
thinner, as these can damage the finish on  
the cabinet.  
Do not use volatile agents such as  
insecticides on the projector.  
Cleaning the lens or lens cover  
Use a commercially available blower or lens  
cleaning paper (for glasses and camera  
lenses) for cleaning the lens or lens cover. Do  
not use any liquid type cleaning agents, as  
they may wear off the coating film on the  
surface of the lens or lens cover.  
As the surface of the lens or lens cover can  
easily get damaged, be careful not to scrape  
or hit the lens or lens cover.  
Do not attach rubber or plastic items to the  
projector for long periods.  
The effects of some of the agents in the  
plastic may cause damage to the quality or  
finish of the projector.  
Wipe off dirt gently with a soft flannel cloth.  
Using a chemical cloth (wet/dry sheet type  
cloth, etc.) may deform the components of  
the cabinet or cause cracking.  
Wiping with a hard cloth or using strong  
force may scratch the cabinet surface.  
When the dirt is hard to remove, soak a cloth  
in a mild detergent diluted with water, wring  
the cloth well and then wipe the projector.  
Strong cleaning detergents may discolor,  
warp or damage the coating on the projector.  
Make sure to test on a small, inconspicuous  
area on the projector before use.  
Cleaning the exhaust and intake vents  
Use a vacuum cleaner to clean dust from the  
exhaust vent and the intake vent.  
Mild detergent diluted  
with water  
Info  
• If you want to clean the air vents during  
projector operation, ensure you press  
STANDBY/ON on the projector or  
STANDBY on the remote control and put the  
projector into Standby mode. After the  
cooling fan has stopped, clean the vents.  
Thinner  
Wax  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance Indicators  
The warning lights (power indicator, lamp indicator and temperature warning indicator) on the  
projector indicate problems inside the projector.  
If a problem occurs, either the temperature warning indicator or the lamp indicator will  
illuminate red, and the projector will enter Standby mode. After the projector has entered  
Standby mode, follow the procedures given below.  
Temperature warning indicator  
Lamp indicator  
Top View  
Power indicator  
About the temperature warning indicator  
If the temperature inside the projector increases, due to blockage of the air vents, or the setting  
location, the temperature warning indicator will blink. And if the temperature keeps on rising,  
” will illuminate in the lower left corner of the picture with the temperature warning  
indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then  
the projector will enter Standby mode. When you find the temperature warning indicator  
blinking, be sure to perform the measures described on page 77.  
About the lamp indicator  
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp.” will  
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the  
lamp will automatically turn off and then the projector will automatically enter Standby mode.  
At this time, the lamp indicator will illuminate in red.  
If you try to turn on the projector a fourth time without replacing the lamp, the  
projector will not turn on.  
Indicators on the Projector  
Power indicator  
Red on  
Normal (Standby)  
Normal (Power on)  
Abnormal (See page 77.)  
Normal (Cooling)  
Normal  
The lamp is warming up.  
The lamp is shut down abnormally or requires to be  
changed. (See page 77.)  
Green on  
Red blinks  
Green blinks  
Green on  
Green blinks  
Red on  
Lamp indicator  
Temperature  
warning indicator  
Off  
Normal  
Red on/Red blinks The internal temperature is abnormally high. (See page 77.)  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance indicator  
Problem  
Cause  
Possible Solution  
Normal  
Abnormal  
Temperature  
warning  
indicator  
Off  
Red blinks The internal  
• Temperatures  
around the projector  
are high.  
• Use the projector in an  
area with a temperature of  
lower than 95°F (+35ºC).  
• Relocate the projector to  
an area with proper  
(On)/  
temperature is  
abnormally high.  
Red on  
(Standby)  
• Blocked air intake  
ventilation. (See page 8.)  
• Cooling fan  
breakdown  
• Internal circuit failure  
• Clogged air intake  
• Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 86) for  
repair.  
Lamp  
indicator  
Green on  
(Green  
blinks  
when the  
lamp is  
warming  
up.)  
Red on  
Red on  
The lamp does  
not illuminate.  
• The lamp is shut  
down abnormally.  
• Disconnect the power cord  
from the AC outlet, and  
then connect it again.  
Time to change  
the lamp.  
• Remaining lamp life  
becomes 5% or less.  
• Carefully replace the lamp.  
(See page 78.)  
• Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 86) for  
repair.  
The lamp does  
• Burnt-out lamp  
• Lamp circuit failure  
(Standby) not illuminate.  
• Please exercise care when  
replacing the lamp.  
• Securely install the cover.  
Power  
indicator  
Green on/ Red blinks The power  
• The lamp unit cover • If the power indicator blinks  
Red on  
Green  
blinks  
indicator blinks in  
red when the  
projector is on.  
is open.  
in red even when the lamp  
unit cover are securely  
installed, contact your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 86) for  
advice.  
(Cooling)  
Info  
• If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the  
possible solutions above and then wait until the projector has cooled down completely before  
plugging in the power cord and turning the power back on. (At least 10 minutes.)  
• If the power is turned off for a brief moment due to power outage or some other cause while using  
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate  
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace  
the power cord in the AC outlet and then turn the power on again.  
• The cooling fan keeps the internal temperature of the projector constant and this function is  
controlled automatically. The sound of the cooling fan may change during operation because the fan  
speed may change and this is not a malfunction.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp  
Lamp  
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes  
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life  
(percentage) can be checked with the on-screen display. (See page 57.)  
Purchase a replacement lamp of type AN-K30LP from your place of purchase, nearest Sharp  
Authorized Projector Dealer or Service Center.  
IMPORTANT NOTE TO U.S. CUSTOMERS:  
The lamp included with this projector is backed by a 90-day parts and labor limited  
warranty. All service of this projector under warranty, including lamp replacement,  
must be obtained through a Sharp Authorized Projector Dealer or Service Center.  
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,  
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).  
Hg LAMP CONTAINS MERCURY For State Lamp Disposal  
Information  
U.S.A ONLY  
Caution Concerning the Lamp  
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure  
can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches  
or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition and  
the frequency of use. It is important to note that failure can often result in the bulb cracking.  
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended  
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating  
normally.  
Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.  
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or  
Service Center to assure safe operation.  
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of  
exposure to the gas, consult a doctor as soon as possible.  
Replacing the Lamp  
Caution  
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause  
burns or injury.  
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully  
cool before removing the lamp unit.  
Carefully change the lamp by following the instructions described in this section.  
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector  
Dealer or Service Center.  
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector  
Dealer or Service Center for repair.  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing and Installing the  
Lamp Unit  
Warning!  
• Do not remove the lamp unit from the  
projector right after use. The lamp and parts  
around the lamp will be very hot and may  
cause burns or injury.  
Lamp unit  
AN-K30LP  
Optional  
accessory  
Info  
• Do not touch the glass surface of the lamp  
unit or the inside of the projector.  
• To avoid injury to yourself and damage to the  
lamp, make sure you carefully follow the  
steps below.  
• Do not loosen other screws except for the  
lamp unit cover and lamp unit.  
Press STANDBY/ON on the  
1
STANDBY/ON  
button  
projector or STANDBY on the  
remote control to put the  
projector into Standby mode.  
Disconnect the power cord.  
2
• Unplug the power cord from the AC  
socket.  
• Leave the lamp until it has fully cooled  
down (about 1 hour).  
AC socket  
Remove the lamp unit cover.  
3
• Loosen the user service screw (1) that  
secures the lamp unit cover. Remove the  
lamp unit cover (2).  
User service screw  
(for lamp unit cover)  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp (Continued)  
Securing screws  
Remove the lamp unit.  
4
• Loosen the securing screws from the lamp  
unit. Hold the lamp unit by the handle and  
pull it in the direction of the arrow. At this  
time, keep the lamp unit horizontal and do  
not tilt it.  
Handle  
Insert the new lamp unit.  
5
6
• Press the lamp unit firmly into the lamp unit  
compartment. Fasten the securing screw.  
Replace the lamp unit cover.  
• Align the tab on the lamp unit cover (1)  
and close it (2). Be careful not to get the  
strap caught in the cover. Then tighten the  
user service screw (3) to secure the lamp  
unit cover.  
Info  
• If the lamp unit and lamp unit cover  
are not correctly installed, the power  
will not turn on, even if the power  
cord is connected to the projector.  
Resetting the Lamp Timer  
Reset the lamp timer after replacing the lamp.  
Info  
• Make sure to reset the lamp timer only when  
replacing the lamp. If you reset the lamp timer  
and continue to use the same lamp, this may  
cause the lamp to become damaged or  
explode.  
AC socket  
STANDBY/ON button  
ENTER button  
R button  
MENU button  
Connect the power cord.  
1
• Plug the power cord into the AC socket of  
the projector.  
Reset the lamp timer.  
2
• While simultaneously holding down  
MENU, ENTER and R on the projector,  
press STANDBY/ON on the projector and  
keep all four buttons pressed down until  
the lamp indicator starts blinking green.  
• “LAMP 0000H” is displayed, indicating  
that the lamp timer is reset.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compatibility Chart  
Computer  
x Multiple signal support  
Horizontal Frequency: 15–110 kHz, Vertical Frequency: 43–85 Hz, Pixel Clock: 12–170 MHz  
x Compatible with sync on green and composite sync signals (TTL level)  
Horizontal  
Frequency [kHz]  
Vertical  
Frequency[Hz]  
Analog  
Support  
Digital  
Support  
PC/MAC  
Mode  
Resolution  
Display  
27.0  
31.5  
37.9  
27.0  
31.5  
37.9  
26.2  
31.5  
34.7  
37.9  
37.5  
43.3  
31.3  
35.2  
37.9  
46.6  
48.1  
46.9  
53.7  
40.3  
48.4  
56.5  
60.0  
68.7  
45.0  
47.8  
49.7  
47.7  
47.8  
55.9  
55.0  
66.2  
67.5  
60.0  
64.0  
64.0  
65.3  
55.9  
65.3  
66.8  
60  
70  
85  
60  
70  
85  
50  
60  
70  
72  
75  
85  
50  
56  
60  
70  
72  
75  
85  
50  
60  
70  
75  
85  
60  
60  
60  
60  
60  
60  
60  
70  
75  
60  
60  
60  
60  
60  
60  
60  
640 × 400  
720 × 400  
640 × 480  
VGA  
SVGA  
XGA  
800 × 600  
1024 × 768  
Upscale  
PC  
1280 × 720  
1280 × 768  
1280 × 800  
1360 × 768  
1366 × 768  
1440 × 900  
WXGA  
WXGA+  
SXGA  
1152 × 864  
1280 × 960  
1280 × 1024  
SXGA+  
1400 × 1050  
1600 × 900  
1680 × 1050  
1920 × 1080  
*
1
WSXGA+  
Down sampled  
Intelligent  
Compression  
2
1920 × 1080  
*
67.5  
60  
MAC 13"  
MAC 16"  
MAC 19"  
MAC 21"  
VGA  
SVGA  
XGA  
640 × 480  
832 × 624  
1024 × 768  
1152 × 870  
34.9  
49.7  
60.2  
68.7  
67  
75  
75  
75  
Upscale  
SXGA  
*1 When a 1920 × 1080 analog signal is input, the image is compressed before it is displayed on the screen.  
*2 Full image display when “Resolution” is set to “1920 × 1080”  
Note  
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)  
mode. Should this occur, turn off the LCD display on the notebook computer and output the display  
data in “CRT only” mode. Details on how to change display modes can be found in your notebook  
computer’s operation manual.  
When “Screen resolution” of the computer is different from the resolution displayed on the projected  
image, follow the procedures shown below.  
– Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in  
“Screen resolution” of the computer.  
– Depending on the computer you are using, the output signal may not be faithful to the “Screen  
resolution” adjustment. Check the settings of the computer's signal output. If the settings cannot be  
changed, it is recommended that the resolution be set to “1920 × 1080” or “1280 × 720”.  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compatibility Chart (Continued)  
DTV  
Horizontal  
Vertical  
Analog  
Digital  
Horizontal  
Vertical  
Analog  
Digital  
Signal  
Signal  
Frequency (kHz)  
Frequency (Hz)  
Support Support  
Frequency (kHz)  
Frequency (Hz)  
Support Support  
15.7  
31.5  
33.8  
15.6  
31.3  
37.5  
45.0  
60  
60  
60  
50  
50  
50  
60  
28.1  
33.8  
27.0  
28.1  
33.8  
56.3  
67.5  
50  
60  
24  
25  
30  
50  
60  
480I  
480P  
540P  
576I  
1080I  
1080I  
1080P  
1080P  
1080P  
1080P  
1080P  
576P  
720P  
720P  
3D  
Horizontal  
Vertical  
Analog  
Digital  
Format  
Signal  
Frequency (kHz)  
Frequency (Hz)  
Support Support  
720P  
720P  
75.0  
90.0  
54.0  
37.5  
45.0  
28.1  
33.8  
56.3  
67.5  
37.5  
45.0  
27.0  
56.3  
67.5  
50  
60  
24  
50  
60  
50  
60  
50  
60  
50  
60  
24  
50  
60  
Frame  
Packing  
1080P  
720P  
720P  
1080I  
1080I  
1080P  
1080P  
720P  
Side By  
Side  
720P  
Top And  
Bottom  
1080P  
1080P  
1080P  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Problem  
Check  
Page  
27  
x Projector power cord is not plugged into the wall outlet.  
x Power to the external connected devices is off.  
x The selected input mode is wrong.  
35  
x Cables are incorrectly connected to the projector.  
x Remote control battery has run out.  
23-27  
16  
x External output has not been set when connecting notebook com-  
puter.  
No picture or projector  
does not start  
x The lamp unit cover is not installed correctly.  
x The selected “Signal Type” is wrong.  
x “Bright” is set to minimum position.  
x Image adjustments are incorrectly set.  
79, 80  
50  
45  
45  
(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)  
x Input signal type is incorrectly set.  
50  
Color is faded or poor.  
x Adjust the focus.  
30  
21  
x The projection distance exceeds the focus range.  
(Computer input)  
x Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)  
x Noise may appear depending on the computer.  
49  
x The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Re- 48  
duction) setting is not correct.  
x There is fog on the lens. If the projector is carried from a cold room into  
a warm room, or if it is suddenly heated, condensation may form on the  
surface of the lens and the image will become blurred. Please set up the  
projector at least one hour before it is to be used. If condensation should  
form, remove the power cord from the wall outlet and wait for it to clear.  
Picture is blurred;  
noise appears.  
An unusual sound is  
occasionally heard  
from the cabinet.  
x If the picture is normal, the sound is due to cabinet shrinkage  
caused by a room temperature changes. This will not affect opera-  
tion or performance.  
Maintenance  
indicator on the  
x See “Maintenance Indicators”.  
76  
50  
projector illuminates.  
Picture is green when  
receiving YPbPr  
x Change the input signal type setting.  
signals and the video  
equipment is connected  
to the Component  
(YPB(CB)PR(CR))  
or COMPUTER/  
COMPONENT terminal  
on the projector.  
Picture is pink when re-  
ceiving RGB signals and  
the video equipment is  
connected to the Com-  
ponent (YPB(CB)PR(CR))  
or COMPUTER/  
COMPONENT terminal  
on the projector.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting (Continued)  
Problem  
Check  
Page  
50  
The black levels of the  
image show banding  
or appear faded when  
HDMI1 or 2 is selected.  
x Make adjustments that result in the best picture quality in the “Dy-  
namic Range” setting.  
Picture is too bright and x Image adjustments are incorrectly set.  
45  
whitish.  
The lens shift function  
does not work.  
x The lens cover is not attached correctly.  
13  
The cooling fan  
becomes noisy.  
x When temperature inside the projector increases, the cooling fan  
runs faster.  
The lamp does not light x The lamp indicator is illuminating in red.  
28, 76, 79  
up even after the  
Replace the lamp.  
projector turns on.  
The lamp suddenly turns  
off during projection.  
The image sometimes  
flickers.  
x Cables are incorrectly connected to the projector or the connected  
23-27  
79  
equipment works improperly.  
x If this happens frequently, replace the lamp.  
The lamp needs much  
time to turn on.  
x The lamp will eventually need to be changed.  
While the remaining lamp life draws to a close, replace the lamp.  
79  
Picture is dark.  
One Touch Play is not  
enabled.  
x Non-Sharp Video Products are connected.  
One Touch Play function may not work when the projector is con-  
nected to non-Sharp Video Products.  
55  
24  
x An HDMI cable is not used for connection between the projector  
and the Sharp Video Products.  
One Touch Play function is enabled when the projector is con-  
nected to the Sharp Video Products with an HDMI cable.  
x One Touch Play function of the projector is not set to “On”.  
55  
x CEC settings of connected Sharp Video Products or other CEC  
devices are incorrect.  
x One Touch Play is set to “Off” and disabled when the Economy  
54, 55  
55  
mode is set to “On”.  
System Standby is not  
enabled.  
x Non-Sharp Video Products are connected.  
System Standby function may not work when the projector is con-  
nected to non-Sharp Video Products.  
x An HDMI cable is not used for connection between the projector  
and the Sharp Video Products.  
System Standby function is enabled when the projector is con-  
nected to the Sharp Video Products with an HDMI cable.  
24  
x System Standby function of the projector is not set to “On”.  
55  
x CEC settings of connected Sharp Video Products or other CEC  
devices are incorrect.  
The remote control  
cannot be used.  
x Operate the remote control while pointing it at the projector’s re-  
mote control sensor.  
x The remote control may be too far away from the projector.  
x If direct sunlight or a strong fluorescent light is shining on the  
projector’s remote control sensor, place the projector where it will  
not be affected by strong light.  
17  
17  
17  
x The batteries may be depleted or inserted incorrectly. Make sure  
the batteries are inserted correctly or insert new ones.  
16  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Check  
Page  
68-70  
70  
3D images are not  
displayed.  
x Switch to 3D mode.  
x Is “3D Auto Change” set to “No”? Press 3D ON/OFF to switch to  
3D mode.  
x If “3D Auto Change” is set to “Yes” but no 3D images are dis-  
played, check the display format of the content being viewed.  
Some 3D image signals may not be recognized as 3D images auto-  
matically. Press 3D MENU to select the appropriate display format  
for the 3D image.  
70, 71  
x The IR emitter is not correctly connected to the projector.  
67  
67  
x Make sure that the IR emitter is located within the proper operating  
range.  
x The 3D Glasses are not turned on.  
66  
66  
74  
x The 3D Glasses are set to 2D mode.  
x The 3D Glasses operate by receiving the infrared signal from the IR  
emitter. Do not place anything between the IR emitter and the infra-  
red receiver on the 3D Glasses.  
3D Images flicker when  
watching in a room.  
x Images may appear to flicker when fluorescent light or ambient  
light enters your vision.  
-Turn off the lights.  
-Block any ambient light.  
Ghosting (a double im-  
age) occurs without the  
image appearing in 3D.  
x Use “Invert” to change the setting.  
70  
82  
x A signal that does not support 3D is being received. Check whether  
a signal that supports 3D is being received.  
x
If the projector is connected to a computer for 3D image playback,  
check that a stereoscopically-enabled application is being used.  
- Use the applicable software  
- Configure your 3D application at the correct 3D format, resolu-  
tion and refresh rate. To support 3D, your 3D application must be  
configured to run at the correct settings for this projector.  
x If there is strong ambient light, block the light. High intensity light-  
ing can interfere with communication between the 3D Glasses and  
the screen, resulting in some flicker.  
x A picture simultaneously projected from more than two projectors  
may not appear 3D. Use only one projector at a time.  
The projected image is dark. x When a 3D image is projected, the screen may appear darker than  
normal.  
The 3D Glasses turn off x Is there an obstacle between the 3D Glasses and the IR emitter,  
automatically.  
or is something covering the infrared receiver on the 3D Glasses?  
The 3D Glasses turn off automatically after 3 minutes if no signal  
is received. Do not place anything between the IR emitter and the  
infrared receiver on the 3D Glasses.  
Pressing the power but- x The battery in the 3D Glasses is exhausted. If the LED light does  
65  
ton on the 3D Glasses  
does not cause the LED  
light to light.  
not light after pressing the power button for more than one second,  
the battery is exhausted. Replace the battery.  
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or  
interference. If this should happen, unplug the unit and plug it in again after more than 5 minutes.  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For SHARP Assistance  
If you encounter any problems during setup or operation of this projector, first  
refer to the “Troubleshooting” section on pages 83 to 85. If this operation  
manual does not answer your question, please contact the SHARP Service  
departments listed below.  
U.S.A.  
Sharp Electronics Corporation  
1-888-GO-SHARP (1-888-467-4277)  
Benelux  
SHARP Electronics Benelux BV  
0900-SHARPCE (0900-7427723)  
Nederland  
9900-0159 Belgium  
Canada  
Mexico  
Sharp Electronics of Canada Ltd.  
(905) 568-7140  
Australia  
Sharp Corporation of Australia Pty.  
Ltd.  
1300-135-022  
Sharp Electronics Corporation  
Mexico Branch  
(525) 716-9000  
New Zealand Sharp Corporation of New Zealand  
Phone: (09) 573-0111  
Latin America Sharp Electronics Corp. Latin  
American Group  
Fax: (09) 573-0112  
(305) 264-2277  
Singapore  
Hong Kong  
Taiwan  
Sharp-Roxy Sales (S) Pte. Ltd.  
65-226-6556  
Germany  
U.K.  
Sharp Electronics (Europe) GMBH  
01805-234675  
Sharp-Roxy (HK) Ltd.  
(852) 2410-2623  
Sharp Electronics (U.K.) Ltd.  
08705 274277  
Italy  
Sharp Electronics (Italy) S.P.A.  
(39) 02-89595-1  
Sharp Corporation (Taiwan)  
0800-025111  
France  
Sharp Electronics France  
01 49 90 35 40  
Malaysia  
U.A.E.  
Sharp-Roxy Sales & Service Co.  
(60) 3-5125678  
Sharp Middle East Fze  
971-4-81-5311  
Spain  
Sharp Electronica Espana, S.A.  
93 5819700  
Thailand  
Korea  
Sharp Thebnakorn Co. Ltd.  
02-236-0170  
Switzerland  
Sweden  
Austria  
Sharp Electronics (Schweiz) AG  
0041 1 846 63 11  
Sharp Electronics Incorporated of  
Korea  
(82) 2-3660-2002  
Sharp Electronics ( Nordic ) AB  
(46) 8 6343600  
India  
Sharp Business Systems (India)  
Limited  
(91) 11- 6431313  
Sharp Electronics (Europe) GMBH  
Branch Office Austria  
0043 1 727 19 123  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
Display devices  
Resolution  
XV-Z30000  
0.65" DLP® Chip ×1  
1080P (1920 × 1080)  
Lens  
F number  
Zoom  
F 2.5 – 3.7  
Power, ×2.0 (f = 21.2 – 42.0 mm)  
Focus  
Power  
×2  
×1  
Input terminals HDMI  
Computer/Component  
(mini D-sub 15 pin)  
Component (3RCA)  
TRIGGER  
3D SYNCHRO  
LAN (RJ-45)  
×1 (Y, PB(CB), PR(CR))  
×1 (Power jack DC 12V output)  
×1  
×1  
×1  
Output  
terminals  
Control and  
communication  
terminals  
RS-232C (mini DIN 9 pin)  
Projection lamp  
Rated voltage  
Rated frequency  
Input current  
250 W  
AC 100 – 240 V  
50/60 Hz  
3.5 A  
Power consumption  
(Eco + Quiet)  
Off  
On  
Off  
On  
AC 100 V  
AC 240 V  
AC 100 V  
AC 240 V  
AC 100 V  
AC 240 V  
AC 100 V  
AC 240 V  
348 W  
328 W  
242 W  
232 W  
8.1 W  
8.8 W  
0.3 W  
0.7 W  
Power consumption  
(Economy Mode)  
Operation temperature  
Cabinet  
Dimensions (main body only) [W × H × D]  
41ºF to 95ºF (+5ºC to +35ºC)  
Plastic  
15 61/64" × 4 33/64" × 16"  
(405 × 114.5 × 406.5 mm)  
Weight (approx.)  
16.1 lbs. (7.3 kg)  
As a part of policy of continuous improvement, SHARP reserves the right to make design and  
specification changes for product improvement without prior notice. The performance specification  
figures indicated are nominal values of production units. There may be some deviations from these  
values in individual units.  
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 2,073,600  
pixels (micromirrors). As with any high technology electronic equipment such as large screen  
TVs, video systems and video cameras, there are certain acceptable tolerances that the  
equipment must conform to.  
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots  
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Units: inches (mm)  
15 61/64 (405)  
7 63/64 (202.5)  
ø68  
2 9/64  
(54)  
M4  
M4  
M4  
M4  
M4  
M4  
M4  
M4  
1 5/8  
2 61/64  
(75)  
(41.25)  
3 3/4 (95)  
7 31/64 (190)  
11 63/64 (304)  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
16:9···················································································36  
3D Auto Change·······························································70  
3D Depth Adjust·······························································70  
3D Format·········································································70  
3D Glasses ································································· 64-66  
3D MENU ·········································································70  
3D MENU button························································69, 70  
3D ON/OFF button ·····················································68, 69  
3D SYNCHRO terminal·····················································67  
Lamp indicator ·································································76  
Lamp Timer (Life)······························································57  
Language (on-screen display language) ··························53  
LAN terminal·····································································27  
LED···················································································56  
LENS button·····································································13  
MAC address····································································60  
MEMORY 1, 2 buttons ·····················································56  
MEMORY button ······························································56  
Memory Menu ··································································56  
MENU button····································································42  
MENU HIDE button ··························································38  
Menu Position···································································53  
MNR ·················································································48  
Accessories······································································12  
AC socket·········································································27  
Adjustment buttons ·························································42  
Adjustment foot································································30  
Advanced ·········································································45  
All Reset ···········································································57  
Anamorphic······································································51  
ANAMORPHIC button······················································15  
Auto Power Off·································································54  
Auto Sync·········································································49  
AUTO SYNC button··························································38  
NATIVE··············································································36  
Network············································································58  
No Operation Off ······························································54  
ON button·········································································28  
One Touch Play ································································55  
Optional accessories························································12  
OSD Brightness································································52  
OSD Display ·····································································52  
Overscan ··········································································52  
Background······································································52  
Batteries ···········································································16  
Black Mask·······································································52  
Bright················································································45  
Bright Boost ·····································································48  
BRIGHTNESS button ·······················································37  
Password··········································································58  
PDF···················································································11  
Phase················································································49  
Picture ··············································································44  
Picture Mode····································································44  
PICTURE MODE button ···················································37  
Power cord·································································12, 27  
Power indicator ··························································28, 76  
PRJ-ADJ···········································································54  
PRJ mode···································································22, 53  
CBNR ···············································································52  
CINEMA ZOOM································································36  
Clock ················································································49  
CLR Temp (Color Temperature)········································45  
C.M.S. ··············································································46  
Color·················································································45  
COLOR button··································································37  
Color Enhance··································································48  
COMPONENT button·······················································35  
Component (YPB(CB)PR(CR)) terminals ······························23  
COMPUTER button··························································35  
COMPUTER/COMPONENT terminal ·························23, 25  
Contrast············································································45  
CONTRAST button···························································37  
Custom Gamma ·······························································46  
Remote control·································································15  
Remote control sensors ···················································17  
Replacing the lamp···························································78  
Reset Network Setting ·····················································59  
RESIZE button··································································36  
Restart Network ·······························································59  
RETURN button································································42  
RS-232C terminal·····························································26  
Detail Enhance ·································································48  
DHCP Client ·····································································59  
DNR··················································································48  
Dynamic Range································································50  
SCR-ADJ··········································································51  
Screen Size and Projection Distance ·······························21  
Sharp················································································45  
SIG-ADJ ···········································································49  
Signal Info·········································································50  
Signal Type·······································································50  
SMART ZOOM ·································································36  
SPHERE ···········································································34  
STANDBY button······························································28  
STANDBY/ON button ·······················································28  
System Standby·······························································55  
Economy Mode ································································54  
ECO+QUIET button··························································38  
ENTER button···································································42  
Exhaust vent·························································13, 14, 75  
Fan Mode ·········································································56  
Film Mode·········································································48  
FOCUS buttons································································30  
Gamma·············································································45  
GEOMETRIC ADJUSTMENT············································32  
TCP/IP··············································································59  
Temperature warning indicator·········································76  
Tint····················································································45  
TINT button ······································································37  
Trigger···············································································51  
TRRIGER teminal······························································14  
H&V KEYSTONE·······························································33  
H&V SHIFT button····························································29  
HDMI1, 2 buttons·····························································35  
HDMI1, 2 terminals·····················································23, 24  
H-Pos ···············································································49  
Video Seup·······································································50  
Viewing Time Info ·····························································70  
V-Image Shift····································································51  
V-Pos················································································49  
INPUT modes···································································35  
Input Name·······································································55  
Intake vent··································································14, 75  
Invert·················································································70  
IP address ········································································60  
IR emitter··········································································67  
IRIS1, 2·············································································45  
IRIS1, 2 buttons································································38  
ZOOM 14:9·······································································36  
ZOOM buttons ·································································30  
Kensington Security Standard connector ························14  
KEYSTONE button ···························································31  
Keystone Correction·························································31  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Microphone PG52 User Manual
Singer Sewing Machine 143G2 User Manual
Sony Camcorder CCD TR3000 User Manual
Sony Projector VPL CX20A User Manual
Sony Projector VPLFX52L User Manual
Sony Stereo Receiver STR DN1060 STR DN860 User Manual
Sony Video Game Console SCPH 50006 User Manual
Sony Video Game Console SCPH 75001 User Manual
Speco Technologies Security Camera CVC 6700 Series User Manual
System Sensor Stud Sensor EM 1RI User Manual