XV-Z15000
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
IMPORTANT
• For your assistance in reporting the loss or theft of
your Projector, please record the Serial Number lo-
cated on the bottom of the projector and retain this
information.
• Before recycling the packaging, please ensure that
you have checked the contents of the carton thor-
oughly against the list of “Supplied accessories” on
page 8.
Model No.: XV-Z15000
Serial No.:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain
or moisture.
See bottom of projector.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
WARNING:
-1
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the operation manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
FCC Regulations state that any unauthorized changes or modifications to this equipment not ex-
pressly approved by the manufacturer could void the user’s authority to operate this equipment.
WARNING:
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL XV-Z15000
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal
of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities, the Electronics Industries Al-
1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 50.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 2,073,600 pixels (micromirrors). As
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Setup
Contents...........................................................3
How to Read this Operation Manual .............4
IMPORTANT SAFEGUARDS............................5
Accessories .....................................................8
Part Names and Functions.............................9
Using the Remote Control............................12
Inserting the Batteries.......................................... 12
Usable Range ..................................................... 12
Setting Up the Projector...............................15
Setting Up the Projector...................................... 15
Standard Setup (Front Projection)........................ 15
Projection (PRJ) Mode......................................... 16
Ceiling-mount Setup ........................................... 16
Screen Size and Projection Distance................... 17
Connections
Samples of Cables for Connection..............18
Connecting to Video Equipment ..................19
Connecting to a Computer...........................20
Controlling the Projector by a Computer....21
Quick Start
Quick Start .....................................................13
Using
Selecting the Film Mode...................................... 39
Setting Detail Enhancement ................................ 39
Reducing Image Noise (DNR).............................. 39
Mosquito Noise Reduction (MNR) ....................... 39
Resetting All Adjustment Items............................ 39
Computer Image Adjustment (“SIG-ADJ” Menu)...40
Adjusting the Computer Image............................ 40
Setting the Resolution ......................................... 40
Auto Sync (Auto Sync Adjustment)...................... 40
Signal Type Setting.............................................. 40
Setting the Video System.................................... 41
Setting the Video Setup....................................... 41
Adjusting the Dynamic Range ............................. 41
Signal Info........................................................... 41
Adjusting the Projected Image (“SCR-ADJ” Menu)...42
Setting the Resize Mode ..................................... 42
Adjusting the Image Position............................... 42
Adjusting the Overscan ....................................... 42
Auto V-Keystone Correction................................ 43
Keystone Mode Correction.................................. 43
Setting On-screen Display................................... 44
Setting the Brightness of the Menu Screen.......... 44
Selecting the Background Image......................... 44
Selecting the Menu Screen Position .................... 44
Reversing/Inverting Projected Images.................. 44
Selecting the On-screen Display Language ......... 44
Adjusting the Projector Function (“PRJ-ADJ” Menu)...45
Setting Auto Power Off Mode.............................. 45
Setting the Power Save Mode (Economy Mode) ... 45
Setting One Touch Play, System Standby
Basic Operation
Turning the Projector On/Off........................22
Connecting the Power Cord................................ 22
Turning the Projector On ..................................... 22
Turning the Power Off
(Putting the Projector into Standby Mode)..... 22
Image Projection ...........................................23
Adjusting the Projected Image............................. 23
Keystone Correction............................................ 24
Auto V-Keystone Correction................................ 25
Switching the Input Mode.................................... 26
Adjusting the Vertical and Horizontal Position of the Image... 26
Displaying the Black Screen Temporarily ............. 27
Freezing a Moving Image..................................... 27
Auto Sync (Auto Sync Adjustment)...................... 27
Selecting the Picture Mode ................................. 27
Displaying an Enlarged Portion of an Image......... 28
Switching the Iris Setting..................................... 28
Hiding the Menu Temporarily (Menu Hide) ........... 28
Switching the Eco+Quiet Mode........................... 28
Resize Mode....................................................... 29
Useful Features
Menu Bar Items .............................................31
Using the Menu Screen.................................34
Menu Selections (Adjustments) ........................... 34
Picture Adjustment (“Picture” Menu) ..........36
Selecting the Picture Mode ................................. 36
Adjusting the Image ............................................ 36
Switching the Iris Setting..................................... 37
Eco+Quiet........................................................... 37
Using the Advanced............................................ 37
Correcting Gradation of Video (Gamma Correction) ... 37
Adjusting the Colors............................................ 37
Adjusting the Bright Boost................................... 39
and Input Name............................................ 45
Setting the Demo Mode....................................... 46
Selecting the Transmission Speed (RS-232C)...... 46
Fan Mode Setting................................................ 46
Returning the Default Settings............................. 46
Lamp Timer (Life) ................................................ 46
Reference
Connecting Pin Assignments.......................53
RS-232C Specifications and Commands....54
Computer Compatibility Chart.....................57
Troubleshooting.............................................58
For SHARP Assistance..................................60
Specifications ................................................61
Dimensions ....................................................62
Index ...............................................................63
Appendix
Maintenance ..................................................47
Maintenance Indicators................................48
Regarding the Lamp......................................50
Lamp .................................................................. 50
Caution Concerning the Lamp............................. 50
Replacing the Lamp............................................ 50
Removing and Installing the Lamp Unit................ 51
Resetting the Lamp Timer................................... 52
-3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect and operate all models
in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and may differ slightly
from the actual display.
Using the Menu Screen
Adjustment buttons
(ꢀ/ꢁ/?/_)
MENU button
Adjustment buttons
(ꢀ/ꢁ/?/_)
RETURN button
ENTER button
MENU button
ENTER button
RETURN button
Buttons used in this operation
Menu Selections (Adjust-
ments)
• This operation can also be performed by using
the buttons on the projector.
Button used in this step
On-screen display
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
1
2
Press MENU.
• The “Picture” menu screen for the se-
lected input mode is displayed.
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Menu bar
Standard
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Press _ or ? to select the menu
screen to adjust on the menu
bar.
Blue
CLR Temp
IRIS1 (Manual)
High Brightness
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
On
Off
SEL./ADJ.
RETURN
ENTER
END
-34
............ Indicates safeguards for using the projector.
............ Indicates additional information for setting up and operating the projector.
Info
Note
For Future Reference
Maintenance
Troubleshooting
Index
P. 47
P. 58 and 59
P. 63
-4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to as-
sure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for
its installation, use and servicing.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read before
the product is operated.
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
14. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable system.
This will prevent damage to the product due to lightning and
power-line surges.
3. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
15. Overloading
5. Cleaning
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
16. Object and Liquid Entry
6. Attachments
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
9. Transportation
A product and cart combination should
be moved with care. Quick stops, exces-
sive force, and uneven surfaces may
cause the product and cart combination
to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
or other hazards.
20. Safety Check
11. Power Sources
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in proper operating condition.
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
21.
Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
12. Grounding or Polarization
This product is provided with one of the following types of plugs.
If the plug should fail to fit into the power outlet,
please contact your electrician.
22. Heat
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles
if lamp ruptures. In case of lamp
rupture, contact your nearest Sharp
Authorized Projector Dealer or Service
Center for replacement.
Warning about placing the projector in a high
position
■ When placing the projector in a high position, make cer-
tain it is carefully secure to avoid personal injury caused
by the projector falling down.
See “Regarding the Lamp” on page
50.
Do not subject the projector to hard impact
and/or vibration.
■ Protect the lens so as not to hit or damage the surface
Caution concerning the setup of the projector
■ For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in
an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the vents and lens must be cleaned more often. As
long as the projector is regularly cleaned, use in these
environments will not reduce the overall operation life of
the unit. Internal cleaning should only be performed by
a Sharp Authorized Projector Dealer or Service Center.
of the lens.
Rest your eyes occasionally.
■
Continuously watching the screen for long hours will
cause eye strain. Take regular breaks to rest your eyes.
Avoid locations with extremes of temperature.
■ The operating temperature of the projector is from 41°F
to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is from –4°F
to 140°F (–20°C to +60°C).
Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes out
the colors, making viewing difficult. Close the curtains
and dim the lights when setting up the screen in a sunny
or bright room.
Do not block the exhaust and intake vents.
■ Allow at least 1113/16 inches (30 cm) of space between
the exhaust vent and the nearest wall or obstruction.
■ Ensure that the intake vent and the exhaust vent are not
obstructed.
■ If the cooling fan becomes obstructed, a protection
circuit will automatically put the projector into standby
mode to prevent overheat damage. This does not indi-
cate a malfunction. (See page 48.) Remove the projector
power cord from the wall outlet and wait at least 10 min-
utes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.
Caution regarding placing of the projector
■ Place the projector on a level site within the adjustment
range (9 degrees) of the adjustment foot.
Caution regarding usage of the projector
■ If you are not to use the projector for a long time or
before moving the projector, make certain you unplug
the power cord from the wall outlet, and disconnect any
other cables connected to it.
■ After the projector is purchased, a faint smell from the
vent may appear when the power is first turned on. This
is normal and is not a malfunction. It will disappear after
the projector is used for a while.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure that you close the
lens shutter.
■ Do not expose the projector to direct sunlight or place
next to heat sources. Doing so may affect the cabinet
color or cause deformation of the plastic cover.
When using the projector in high-altitude areas
such as mountains (at altitudes of approximate-
ly 4,900 feet (1,500 meters) or more)
■ When you use the projector in high-altitude areas with
thin air, set “Fan Mode” to “High”. Neglecting this can
affect the longevity of the optical system.
-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connected equipment
Info
■ When connecting a computer or other audio-visual
equipment to the projector, make the connections AFTER
unplugging the power cord of the projector from the AC
outlet and turning off the equipment to be connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
• The cooling fan regulates the internal temperature,
and its performance is automatically controlled.
The sound of the fan may change during projector
operation due to changes in the fan speed. This
does not indicate malfunction.
Using the projector in other countries
■ The power supply voltage and the shape of the plug may
vary depending on the region or country you are using the
projector in. When using the projector overseas, make
sure you use an appropriate power cord for the country
you are in.
Temperature monitor function
■ If the temperature inside the projector increases, due
to blockage of the air vents, or the setting location,
the temperature warning indicator will blink. And if the
temperature keeps on rising, “
” will illuminate in
the lower left corner of the picture with the temperature
warning indicator blinking. If this state continues, the
lamp will turn off, the cooling fan will run and then the
projector will enter standby mode. Refer to “Maintenance
Indicators” on pages 48 and 49 for details.
• The DLP® logo and the DLP® medallion are registered trademarks of Texas Instruments.
•
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru-
ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or
discompile the contents thereof.
-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Remote control
<RRMCGA757WJSA>
Two AA size batteries
<UBATUA020WJZZ>
Operation manual
(4)
Power cord*
(1)
(2)
(3)
For U.S. and
Canada, etc.
(6' (1.8 m))
For Europe,
except U.K.
(6' (1.8 m))
For U.K. and
Singapore
(6' (1.8 m))
For Australia,
New Zealand and Oceania
(6' (1.8 m))
<QACCDA007WJPZ> <QACCVA011WJPZ> <QACCBA036WJPZ>
<QACCLA018WJPZ>
* Use the power cord that corresponds to the wall outlet in your country.
Note
x Codes in “< >” are Replacement parts codes.
Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
AN-K15LP
AN-60KT
AN-XGCM55 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XGCM55>
(for U.S.A. only)
■ Ceiling-mount unit
■ 3 RCA to mini D-sub 15 pin cable (10' (3.0 m))
AN-C3CP2
Note
x Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector
Top View
PICTURE MODE button
27
34
For selecting the appropriate picture.
AUTO V-KEYSTONE
button
25
ENTER button
For setting items selected or adjusted
on the menu.
Vertical keystone correction is
performed automatically.
INPUT buttons (P/R)
26
34
STANDBY/ON button
For switching input mode.
13, 22
For turning the power on
and putting the projector
into standby mode.
Adjustment buttons (P/R/O/Q)
For selecting menu items.
Power indicator
Lamp indicator
22, 48
22, 48
48
Temperature warning
indicator
RESIZE button
29
For switching the picture
RETURN button
For returning to the previous menu
screen during menu operations.
34
34
size (NORMAL, STRETCH, etc.).
MENU button
For displaying adjustment and setting
screens.
Front View
Exhaust vent
47
Zoom ring
14, 23
14, 23
Remote control sensor
12
For enlarging/
reducing the picture.
Focus ring
For adjusting the focus.
Intake vent
47
HEIGHT ADJUST lever
Adjustment foot
Lens shutter
23
14, 23
Adjustment foot
23
22, 27, 51
-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Projector (Rear View)
Terminals
HDMI1, 2 terminals
Terminal for connecting video
equipment with HDMI output
terminal.
COMPONENT terminals
18
18, 19
Terminal for connecting video
equipment with component
output terminal.
RS-232C terminal
S-VIDEO input
21
18, 19
Terminal for
terminal
controlling the
projector using a
computer.
Terminal for
connecting video
equipment with an
S-video terminal.
COMPUTER/COMPONENT
input terminal
VIDEO input
terminal
18, 20
18
Terminal for computer RGB and
component signals.
Terminal for
connecting
video equipment.
Remote control
sensor
12
Carrying handle
For carrying the projector.
Security bar
Kensington Security
Standard connector
AC socket
Connect the supplied
power cord.
22
Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on the side.
• Always close the lens shutter to prevent damage to the lens when transporting
the projector.
• Do not lift or carry the projector by the lens as this may damage the lens.
Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System.
Refer to the information that came with the system for instructions on how to use it to secure the projector.
-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Remote Control
STANDBY button
For putting the projector into
the standby mode.
ON button
For turning the power on.
14, 22
13, 22
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
27
27
HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO,
COMPUTER buttons
For switching to the respective
input modes.
14, 26
PICTURE MODE button
For selecting the appropriate
picture.
FREEZE button
For freezing images.
27
28
IRIS 1, 2 buttons
For switching “High Brightness”
and “High Contrast”.
MAGNIFY buttons
For enlarging/reducing part of the
image.
28
KEYSTONE button
IMAGE SHIFT button
For shifting images horizontally
and vertically.
24
34
26
34
For entering the Keystone mode.
Adjustment
ENTER button
For setting items selected or
adjusted on the menu.
buttons (P/R/O/Q)
For selecting and adjusting menu
items.
RETURN button
For returning to the previous menu
screen during menu operations.
MENU button
For displaying adjustment and
setting screens.
34
34
INPUT button
RESIZE button
For switching the picture size
(NORMAL, STRETCH, etc.).
26
28
29
28
For switching input mode.
MENU HIDE button
For temporarily hiding menu
screen.
ECO+QUIET button
For lowering the noise of the
cooling fan and extending the
lamp life.
-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Inserting the Batteries
1 Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2 Insert the supplied batteries and
put back the cover.
• Make sure the polarities correctly match
the m and n marks inside the battery
compartment.
• When putting back the cover, be sure that
the cover clicks in place and settles.
30°
30°
Usable Range
23' (7 m)
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Remote
control
sensors
Note
• Remote control sensor is located on both the
front and rear of the projector.
• The signal from the remote control can be
reflected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
30°
30°
23' (7 m)
When using the remote control:
• Be sure not to drop, expose to moisture or high
temperature.
Remote control
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projec-
tor away from the fluorescent lamp.
signal transmitter
Remote control
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
•
Insert the batteries making sure the polarities correctly match the
m
and
n
marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them
using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept. Be
sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section provides an example showing how to connect the projector to video equipment that has an HDMI
output terminal with a brief explanation of the steps from connection through to image projection.
For details, see the pages suggested in each step.
3, 7 STANDBY/ON
7 STANDBY button
button
3 ON button
5 Input Mode
Select buttons
6 Zoom ring
5 INPUT button
6 Focus ring
6 Adjustment feet
Page 15
1.Place the projector facing a screen
2.
3.
Connect the projector to the video equipment and plug
the power cord into the AC socket of the projector
Pages 18-22
Page 22
Open the lens shutter fully and then turn the projector on
On the projector
Press STANDBY/ON on the projector or ON on the
remote control pointing the remote control towards
the projector.
2
STANDBY/ON button
On the remote control
2
ON button
1
-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start (Continued)
4.Turn the video equipment on and start playback
Playback
Page 26
5.Select the input mode
Press HDMI1 on the remote control to select “HDMI1” for the Input mode.
HDMI1 button
HDMI1
Component
1080P
• Press HDMI1, HDMI2, COMPONENT, S-VIDEO, VIDEO and COMPUTER on the remote control to
switch the Input mode.
• Press Por Rto select your desired input mode when you press INPUT on the remote control or on the
projector.
Page 23
6.Adjust the projector angle, focus and zoom
1. The focus is adjusted by
rotating the focus ring.
2. Zooming is adjusted by
rotating the zoom ring.
3. The projector angle is
adjusted by using the
adjustment feet.
Focus ring
Zoom ring
Adjustment feet
• When the image is distorted
trapezoidally, the keystone
correction is needed.
(See page 24.)
Page 22
7.Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again
while the confirmation message is displayed, to put the projector into standby mode.
On the projector
On the remote control
On-screen display
1
1
STANDBY/ON button
STANDBY
button
2
-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and
level.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly
on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size.
Example of standard setup
Side View
Screen
H
Lens center
90°
L
Note
• Refer to page 17 for additional information concerning “Screen Size and Projection Distance”.
-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most ap-
propriate for the projection setting in use. (You can set the PRJ Mode in “SCR-ADJ” menu. See page 44.)
■ Table mounted, front projection
■ Ceiling mounted, front projection
Menu item ➞ “Front”
Menu item ➞ “Ceiling + Front”
■ Table mounted, rear projection
■ Ceiling mounted, rear projection
(with a translucent screen)
(with a translucent screen)
Menu item ➞ “Rear”
Menu item ➞ “Ceiling + Rear”
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before
mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain
the recommended ceiling-mount adaptor and unit (sold separately).
Indication of the Projection Image Size and Projection Distance
For details, refer to “Screen Size and Projection Distance” on page 17.
Example : When using a wide screen (16:9)
Picture Size
500"
436
"
×
245
"
200"
174
"
×
98
"
100"
80"
87
"
×
49
70
"
"
×
39
"
40"
Projection
Distance
35
20
"
"
×
4'1" ~ 4'9"
(1.3 m ~ 1.84'm3)" ~ 9'6"
51'6"
(15.7 m)
(2.5 m ~ 2.9 m)
20'7" ~ 23'9"
(6.3 m ~ 7.2 m)
10'4" ~ 11'11"
(3.1 m ~ 3.6 m)
-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
When using a wide screen (16:9): In case of displaying the 16:9 picture on the whole of the 16:9 screen.
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
500"
Height
245"
196"
147"
123"
98"
74"
59"
49"
39"
(1270 cm)
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(152 cm)
(102 cm)
436"
349"
261"
218"
174"
131"
105"
87"
(1107 cm)
(886 cm)
(664 cm)
(553 cm)
(443 cm)
(332 cm)
(266 cm)
(221 cm)
(177 cm)
(133 cm)
(89 cm)
(623 cm)
(498 cm)
(374 cm)
(311 cm)
(249 cm)
(187 cm)
(149 cm)
(125 cm)
(100 cm)
(75 cm)
51'6"
41'2"
30'11"
25'9"
20'7"
15'5"
12'4"
10'4"
8'3"
(15.7 m)
(12.6 m)
(9.4 m)
(7.9 m)
(6.3 m)
(4.7 m)
(3.8 m)
(3.1 m)
(2.5 m)
(1.9 m)
(1.3 m)
39 3/8"
31 1/2"
23 5/8"
(100 cm)
(80 cm)
(60 cm)
(50 cm)
(40 cm)
(30 cm)
(24 cm)
(20 cm)
(16 cm)
(12 cm)
(8 cm)
—
400"
300"
250"
200"
150"
120"
100"
80"
47'6"
35'8"
29'8"
23'9"
17'10"
14'3"
11'11"
9'6"
(14.5 m)
(10.9 m)
(9.1 m)
(7.2 m)
(5.4 m)
(4.3 m)
(3.6 m)
(2.9 m)
(2.2 m)
(1.4 m)
19 11
/
"
16
15 3/4"
11 13
9 29
/
/
"
"
16
64
7 7/8"
70"
52"
6 19
4 23
3 5
/
/
/
"
64
"
32
"
32
60"
40"
29"
6'2"
7'2"
35"
20"
(50 cm)
4'1"
4'9"
x
: Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L : Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
[Feet/inches]
L1(ft) = 0.0314
L2(ft) = 0.0362
[m/cm]
L1(m) = 0.0314
L2(m) = 0.0362
x
x
/ 0.3048
/ 0.3048
/ 2.54
x
x
H : Distance from the lens center to the bottom of the image (in/cm)
H (in) = 0.2
x
H (cm) = 0.2
x
When using a normal screen (4:3) and projecting 4:3 image (NORMAL Mode)
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
400"
Height
240"
180"
150"
120"
90"
72"
60"
48"
42"
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(178 cm)
(152 cm)
(102 cm)
320"
240"
200"
160"
120"
96"
(813 cm)
(610 cm)
(508 cm)
(406 cm)
(305 cm)
(244 cm)
(203 cm)
(163 cm)
(142 cm)
(122 cm)
(81 cm)
(610 cm)
(457 cm)
(381 cm)
(305 cm)
(229 cm)
(183 cm)
(152 cm)
(122 cm)
(107 cm)
(91 cm)
50'5"
37'10"
31'6"
25'3"
18'11"
15'2"
12'7"
10'1"
8'10"
7'7"
(15.4 m)
(11.5 m)
(9.6 m)
(7.7 m)
(5.8 m)
(4.6 m)
(3.8 m)
(3.1 m)
(2.7 m)
(2.3 m)
(1.5 m)
38 35
28 29
24 3
19 17
14 29
11 9
9 41
/
/
/
/
/
/
/
/
"
64
"
32
"
32
"
64
"
64
"
16
"
64
"
64
(98 cm)
(73 cm)
(61 cm)
(49 cm)
(37 cm)
(29 cm)
(24 cm)
(20 cm)
(17 cm)
(15 cm)
(10 cm)
—
300"
250"
200"
150"
120"
100"
80"
70"
60"
40"
43'7"
36'4"
29'1"
21'10"
17'5"
14'6"
11'8"
10'2"
8'9"
(13.3 m)
(11.1 m)
(8.9 m)
(6.6 m)
(5.3 m)
(4.4 m)
(3.5 m)
(3.1 m)
(2.7 m)
(1.8 m)
80"
64"
7 45
56"
48"
6 3/4"
36"
5 25
3 55
/
/
"
"
32
32"
24"
(61 cm)
5'1"
5'10"
64
The formula for picture size and projection distance
x
: Picture size (diag.) (in/cm)
L : Projection distance (ft/m)
[Feet/inches]
[m/cm]
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H : Distance from the lens center to the bottom of the image (in/cm)
L1(ft) = 0.03843
x
/ 0.3048
/ 0.3048
/ 2.54
L1(m) = 0.03843
x
x
L2(ft) = 0.0443
x
L2(m) = 0.0443
x
H (in) = 0.24477
x
H (cm) = 0.24477
When using a normal screen (4:3): In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
Picture (Screen) size
Width
Projection distance [L]
Minimum [L1] Maximum [L2]
Distance from the lens center to
the bottom of the image [H]
Diag. (x)
500"
Height
300"
(1270 cm)
(1016 cm)
(762 cm)
(635 cm)
(508 cm)
(381 cm)
(305 cm)
(254 cm)
(203 cm)
(178 cm)
(152 cm)
(102 cm)
400"
320"
240"
200"
160"
120"
96"
(1016 cm)
(813 cm)
(610 cm)
(508 cm)
(406 cm)
(305 cm)
(244 cm)
(203 cm)
(163 cm)
(142 cm)
(122 cm)
(81 cm)
(762 cm)
(610 cm)
(457 cm)
(381 cm)
(305 cm)
(229 cm)
(183 cm)
(152 cm)
(122 cm)
(107 cm)
(91 cm)
47'3"
37'10"
28'4"
23'8"
18'11"
14'2"
11'4"
9'5"
(14.4 m)
(11.5 m)
(8.6 m)
(7.2 m)
(5.8 m)
(4.3 m)
(3.5 m)
(2.9 m)
(2.3 m)
(2.0 m)
(1.7 m)
(1.2 m)
36 9/64"
(92 cm)
(73 cm)
(55 cm)
(46 cm)
(37 cm)
(28 cm)
(22 cm)
(18 cm)
(15 cm)
(13 cm)
(11 cm)
(7 cm)
—
400"
300"
250"
200"
150"
120"
100"
80"
240"
180"
150"
120"
90"
72"
60"
48"
42"
43'7"
32'8"
27'3"
21'10"
16'4"
13'1"
10'11"
8'9"
(13.3 m)
28 29
21 11
18 1
14 29
10 27
8 43
/ "
32
/ "
16
/ "
16
/ "
64
/ "
32
/ "
64
/ "
64
/ "
32
/ "
16
/ "
32
/ "
64
(10.0 m)
(8.3 m)
(6.6 m)
(5.0 m)
(4.0 m)
(3.3 m)
(2.7 m)
(2.3 m)
(2.0 m)
(1.3 m)
80"
64"
7 15
7'7"
5 25
70"
60"
40"
56"
48"
35"
6'7"
7'8"
5 1
36"
5'8"
6'6"
4 11
24"
(61 cm)
3'9"
4'4"
2 57
x
: Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L : Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
[Feet/inches]
[m/cm]
L1(ft) = 0.02882
L2(ft) = 0.03323
H (in) = 0.18358
x
x
x
/ 0.3048
/ 0.3048
/ 2.54
L1(m) = 0.02882
L2(m) = 0.03323
H (cm) = 0.18358
x
x
x
H : Distance from the lens center to the bottom of the image (in/cm)
Note
• Refer to page 15 concerning “Projection distance [L]” and “Distance from the lens center to the bottom of
the image [H]”.
• Allow a margin of error in the value in the diagrams above.
-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Samples of Cables for Connection
•For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on
connected
equipment
Terminal on the
Equipment
Cable
projector
Video equipment
HDMI output HDMI cable (commercially available)
terminal
HDMI1, 2
(
Page 19)
Component Component cable (commercially available)
COMPONENT
video output
terminal
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
S-video
S-video cable (commercially available)
S-VIDEO
output terminal
(
Page 19)
Video output Video cable (commercially available)
terminal
VIDEO
Camera/Video game Component Cables for a camera or a video game/3 RCA to mini COMPUTER/
video
output
terminal
D-sub 15 pin cable (optional, AN-C3CP2)
COMPONENT
RCA adaptor plug
(commercially available)
S-video
output
Cables for a camera or a video game
Cables for a camera or a video game
RGB cable (commercially available)
S-VIDEO
VIDEO
terminal
Video
output
terminal
Computer
RGB
output
terminal
COMPUTER/
COMPONENT
(
Page 20)
HDMI output HDMI cable (commercially available)
terminal
HDMI1, 2
-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off the devices
to be connected. After making all connections, turn on the projector and then the other devices.
Connecting Equipment with HDMI Output Terminal to the HDMI Terminal on the Projector
HDMI is a new specialized interface capable of delivering a video and audio signal to the terminal using just one cable.
Since this projector does not support an audio signal by itself, use an amplifier or other audio device.
For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI
standards may result in a malfunction.
HDMI-compatible device
To HDMI output terminal
To HDMI1 or 2 terminal
HDMI cable (type A)
(commercially available)
Note
•HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video
signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
•Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.
Connecting to Equipment with S-video Output Terminal
DVD Player, etc.
To S-VIDEO terminal
To S-video output terminal
S-video cable
(commercially available)
Refer to “Samples of Cables for Connection” on page 18 for connecting other equipment.
-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
Ensure that the computer is the last device to be turned on after all the connections are made.
Connecting to a Computer Using the RGB Cable
Computer
To COMPUTER/COMPONENT terminal
To RGB output terminal
RGB cable
(commercially available)
Note
• Refer to “Computer Compatibility Chart” on page 57 for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions not to work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s external
output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook
computer). Refer to the specific instructions in your computer’s operation manual to enable your computer’s
external output port.
-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector.
When connecting to a computer using an RS-232C serial control cable
Computer
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• For details on RS-232C specifications and commands, see page 54.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
•The power indicator illuminates red, and the
projector enters standby mode.
Power cord
(supplied)
Info
Turning the Projector On
•English is the factory default language. If you
want to change the on-screen display to another
language, change the language according to the
procedure on page 44.
Note that the connections to external equipment and
power outlet should be done before performing the
operations written below. (See pages 19 to 22.)
Power indicator
Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.
•The power indicator illuminates green.
•After the lamp indicator illuminates, the projec-
tor is ready to start operation.
STANDBY/ON button
•When the lens shutter is closed, the power
indicator blinks alternately green and orange
and the projector does not turn on.
Lamp indicator
Note
•About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green:The lamp is warming up.
Red: The lamp is shut down abnormal-
ly or the lamp should be replaced.
•When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has
been illuminated. This is normal operation as
the lamp's control circuitry is stabilising the
lamp output characteristics. It should not be
regarded as faulty operation.
Lens shutter
STANDBY button
ON button
•If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to start projection.
On-screen display
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector or
STANDBY on the remote control, then
press that button again while the confir-
mation message is displayed, to put the
projector into standby mode.
Info
•Direct Power Off function:
You can unplug the power cord from the AC outlet
even if the cooling fan is still running.
•
The projector cannot be turned on while cooling.
-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Adjusting the Projected
Image
Zoom ring
Focus ring
1 Adjusting the Focus
You can adjust the focus with the focus ring
on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
2 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
3 Adjusting the Height
The height of the projector can be adjusted
using the adjustment feet.
When the screen is above the projector, the
projection image can be made higher by
adjusting the projector.
HEIGHT ADJUST lever
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
Make small
adjustments.
been finely adjusted.
•The angle of projection is adjustable up
to 9 degrees from the surface on which
the projector is placed.
Info
•Do not apply too much pressure on the projector
when the front adjustment feet come out.
•When lowering the projector, be careful not to get
your fingers caught in the area between the adjust-
ment feet and the projector.
Note
•When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 24 and 43.)
•Hold the projector firmly while lifting or carrying.
•Do not hold by the lens area.
-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Keystone Correction
This function can correct distortion of an image
projected toward a spherical or cylindrical screen
as well as trapezoidal distortion of an image on a
flat screen and rotate the image at your arbitrary
angle.
KEYSTONE button
ENTER button
■ Keystone
When the image is projected either from the top or
from the bottom towards the screen at an angle, the
image becomes distorted trapezoidally. The
function for correcting trapezoidal distortion is
called Keystone Correction.
Adjustment buttons
(P/R/O/Q)
RETURN button
Note
•The Keystone Correction can be adjusted up
For horizontal keystone correction
For vertical keystone correction
O, Qbutton
P, Rbutton
to an angle of approximately 12 degrees
with “Auto V-Keystone” and up to an angle
of approximately 40 degrees with “V-Key-
stone” and approximately 30 degrees with
“H-Keystone”.
Keystone Correction
H-Keystone Correction:
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears.
KEYSTONE MODE
KEYSTONE
V-Keystone Correction:
SPHERE
ROTATION
SEL.
ENTER
END
Press P/Rto select “KEYSTONE”,
and then press ENTER.
•The keystone menu guide appears.
Note
H: 0
V: 0
KEYSTONE
END
•To return to the default setting, press RETURN
while the on-screen display of the Keystone
mode is on the screen.
ADJUST
TESTPATTERN
RESET
Selectable buttons
Description
Exits the keystone mode.
Adjusts the keystone correction.
END
➞
KEYSTONE
Info
P/R/O/Q
➞
ADJUST
•While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.
TESTPATTERN
➞ENTER
Displays the testpattern.
Returns to a default setting.
RESET➞RETURN
Press P/R/O/Q to adjust the
Keystone Correction.
3
Press KEYSTONE.
•The on-screen display of the Keystone
mode will disappear.
-24
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Sphere
PressP/Rtoselect“ROTATION”,
2
This function can correct distortion of an image
projected toward a spherical or cylindrical screen.
and then press ENTER.
•The rotation menu guide appears.
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears. (See
page 24.)
Selectable items
RETURN
Description
Returns to the keystone mode list.
Adjusts the rotation correction.
Displays the testpattern.
ADJUST
TESTPATTERN
RESET
Returns to a default setting.
Press P/R/O/Q to adjust the
Rotation Correction mode.
Press P/Rto select “SPHERE”,
and then press ENTER.
•The sphere menu guide appears.
Rotates the image clockwise.
P, Qbutton
Selectable items
RETURN
Description
Rotates the image counterclockwise.
R, Obutton
Returns to the keystone mode list.
Adjusts the sphere correction.
Displays the testpattern.
Rotation Correction
ADJUST
TESTPATTERN
RESET
Returns to a default setting.
Press P/R/O/Q to adjust the
Sphere Correction mode.
Note
•
To return to the default setting, press RETURN while the
on-screen display of the Keystone mode is on the screen.
P, Qbutton
For correction of concave distortion
For correction of convex distortion
R, Obutton
Press KEYSTONE.
Sphere Correction
•The on-screen display of the Rotation
Correction mode will disappear.
Correction of Concave Distortion:
Correction of Convex Distortion:
Auto V-Keystone Correction
This function can perform vertical keystone
correction automatically.
Press AUTO V-KEYSTONE on the projec-
tor to perform vertical keystone correction
which is automatically activated in response
to the installation angle of the projector.
•
The on-screen display of the Auto V-Keystone “On” ap-
pears when AUTO V-KEYSTONE is pressed once.
Pressing AUTO V-KEYSTONE again after the on-screen
display of the Auto V-Keystone “On” has appeared
changes the on-screen display of the Auto V-Keystone
“On” to the on-screen display of the Auto V-Keystone
“Off” and the setting of the Auto V-Keystone to “0”.
Pressing AUTO V-KEYSTONE while adjusting the im-
age using Sphere/Rotation Correction changes Sphere/
Rotation Correction mode to Keystone mode.
•
Note
• To return to the default setting, press RETURN while
the on-screen display of the Keystone mode is on the
screen.
•
Press KEYSTONE.
•The on-screen display of the Sphere
Correction mode will disappear.
AUTO V-KEYSTONE button
■ Rotation
This function rotates the image at an arbitrary angle.
Press KEYSTONE to enter the
keystone mode.
•The keystone mode list appears. (See
page 24.)
-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Switching the Input Mode
HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO, COMPUTER
buttons
Select the appropriate input mode for the connected
equipment.
Press HDMI1, 2, COMPONENT,
S-VIDEO, VIDEO or COMPUTER on
the remote control to select the input
mode.
•When you press INPUT on the projector or on
the remote control, the INPUT list appears.
Press P/R to switch the INPUT mode.
IMAGE SHIFT button
Adjustment buttons
(P/R/O/Q)
INPUT list
INPUT button
INPUT
HDMI1
HDMI2
Press P/R/O/Q to adjust the
vertical and horizontal position
of the image.
2
COMPONENT
COMPUTER
S-VIDEO
VIDEO
H-Image Shift
Selectable items
\ button
| button
H-Image Shift
Leftward
Rightward
Adjusting the Vertical and
Horizontal Position of the
Image
\ button
| button
Press IMAGE SHIFTto enter the
image shift mode.
•The image shift menu guide appears.
V-Image Shift
Selectable items
" button
' button
H: 0
V: 0
IMAGE SHIFT
END
ADJUST
V-Image Shift
Downward
Upward
RESET
Selectable buttons
Description
Exits the image shift mode.
Adjusts the image shift.
END
ADJUST
RESET
➞
IMAGE SHIFT
" button
' button
➞
P/R/O/Q
Returns to a default setting.
➞
RETURN
Note
•To return to the default setting, press
RETURN when the image shift menu guide
is still on the screen.
•Depending on the Resize mode, Picture
mode or the input signal resolution, the range
of the image shift may be limited.
-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Black Screen
Temporarily
FREEZE button
AUTO SYNC button
PICTURE MODE button
Close the lens shutter to temporarily display a black
screen.
Note
•When you close the lens shutter, the projector
will be turned off automatically after about 30
minutes.
Freezing a Moving Image
Press FREEZE.
•The projected image is frozen.
Press FREEZE again to return to
the moving image from the cur-
rently connected device.
Auto Sync
(Auto Sync Adjustment)
Selecting the Picture Mode
You can select the appropriate picture mode for the
projected image, such as movie or video game.
Auto Sync function works when detecting input signal
after the projector turns on.
Press PICTURE MODE.
•When pressing PICTURE MODE, the picture mode
changes in the following order:
Press AUTO SYNC to manually adjust with
Auto Sync function.
Standard
Natural
Dynamic
Note
Game
Movie2
Movie1
•When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 40.)
Note
•See page 36 for details on the picture mode.
-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
MAGNIFY buttons
IRIS 1, 2 buttons
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected images
can be enlarged. This is helpful when providing more
detailed explanations.
Adjustment buttons
(P/R/O/Q)
RETURN button
Press
control.
•Enlarges the image.
MAGNIFY on the remote
MENU HIDE button
ECO+QUIET button
•Pressing
or
MAGNIFY enlarges or
reduces the projected image.
Switching the Iris Setting
Note
Press
.
This function controls the quantity of the projected
light and the contrast of the image.
×1 ×2 ×3 ×4 ×9
Press IRIS 1 or 2.
•Each time the button is pressed while the display is
on, the mode changes in the following order:
Press
.
•You can change the location of the en-
larged image using P, R, Oand Q.
■ IRIS 1 High Brightness
■ IRIS 2
High Contrast
On
Off
Press RETURN on the remote con-
trol to cancel the operation.
•To return to the default setting (×1), press
RETURN when the on-screen display of the
magnify mode is displayed.
Note
•For details, see page 37.
Note
Hiding the Menu Temporarily
(Menu Hide)
•The selectable magnifications differ de-
pending on the input signal.
•In the following cases, the image will return
to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed while
the on-screen display of the magnify
mode is displayed.
When the menu screen is displayed, you can tempo-
rarily hide the menu screen by pressing and holding
MENU HIDE on the remote control. This is useful
when, for example, checking the video adjustment
information.
- When the input signal is changed.
- When the input signal resolution and re-
fresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When the Picture mode is changed.
Switching the Eco+Quiet Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
•When the Eco+Quiet Mode is set to “On”, the sound of
the cooling fan will turn down, the power consumption
will decrease, and the lamp life will extend.
Note
•Refer to “Eco+Quiet” on page 37 for details.
-28
Download from Www.Somanuals.com. All Manuals Search And Download.
RESIZE button
Resize Mode
This function allows you to modify or customize the
resize mode to enhance the input image.
Press RESIZE on the projector or on the
remote control.
Note
•The RESIZE function that can be selected
varies depending on the input signal
(resolution and vertical frequency).
RESIZE button
Resize Mode
RESIZE
Output screen image
NORMAL
The image is displayed with the original aspect ratio.
STRETCH
An image compressed from a 16:9 aspect ratio to a 4:3 aspect ratio
is restored to a 16:9 aspect ratio and displayed at full-screen.
CINEMA ZOOM
A CinemaScope image or an image with a 16:9 aspect ratio is
displayed at full-screen
-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
RESIZE
Output screen image
ZOOM 14:9
An image with a 14:9 aspect ratio and letterboxing is enlarged while
maintaining the original aspect ratio.
SMART ZOOM
DOT BY DOT
An image with a 4:3 aspect ratio is slightly enlarged.
The image is displayed according to the original input signal.
About Copyrights
•When using the RESIZE function to select an image size with a different aspect ratio to a TV program or
video image, the image will look different from its original appearance. Keep this in mind while choosing an
image size.
•The use of the RESIZE or Overscan function to compress or stretch the image for commercial purposes/public
displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders.
Please use caution.
-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items
The following shows the items that can be set in the projector.
The selectable items vary depending on the selected input, input signals, or adjustment
values. Items that cannot be selected will be grayed out.
Main menu
Sub menu
Picture
Picture Mode
Standard
Natural
Dynamic
Movie1
Movie2
Game
Page 36
Page 36
Contrast –30 +30
Bright –30 +30
“Picture” menu
Color
Tint
–30 +30
–30 +30
Picture
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Standard
0
0
0
0
0
0
0
0
Sharp –30 +30
Red
–30 +30
–30 +30
Blue
–2 +2
CLR Temp
Page 36
High Brightness
On
Off
IRIS1 (Manual)
IRIS1 (Manual)
High Brightness
High Contrast
IRIS2 (Auto)
Eco+Quiet
Advanced
Gamma
Page 37
IRIS2 (Auto)
Page 37
Eco+Quiet
Page 37
Advanced
Page 37
Reset
On
Off
0
0
On
Off
Off
C.M.S.1
C.M.S.2
Bright Boost
Film Mode
Detail Enhance
DNR
On
Off
Gamma
Page 37
C.M.S.1
Page 37
–2 +2
Auto
Off
Off
Select Color
Hue
MNR
Reset
Page 39
SEL./ADJ.
RETURN
ENTER
END
Saturation
Value
Effect
C.M.S.1
Reset
On
Off
“C.M.S.1” menu
Return
Select Color
Hue
C.M.S.1
Select Color
Hue
Saturation
Value
Effect
C.M.S.1
Reset
C.M.S.2
Page 37
0
0
0
0
Saturation
Value
On
Effect
Return
C.M.S.2
Reset
On
Off
Return
Bright Boost
Page 39
On
Off
Film Mode
Page 39
Auto
Off
SEL./ADJ.
RETURN
ENTER
END
Detail
–30 +30
Enhance
Page 39
DNR
Page 39
MNR
Page 39
Off
Level 1
Level 2
Level 3
-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items (Continued)
Main menu
SIG-ADJ
Sub menu
Clock –150 +150
“SIG-ADJ” menu
Page 40
Page 40
Picture
Clock
Phase
H-Pos
V-Pos
SCR-ADJ
PRJ-ADJ
SIG-ADJ
0
0
0
0
Phase –30 +30
Page 40
H-Pos –150 +150
Page 40
Reset
V-Pos –60 +60
Page 40
Resolution
Auto Sync
Signal Type
Video System
Video Setup
On
Auto
Auto
0 IRE
Auto
Reset
Resolution
Page 40
Dynamic Range
Auto Sync
On
Off
Signal Info : 1080P
Page 40
H : XX.X
kHz/
V : XX.X Hz
Signal Type
Auto
RGB
SEL./ADJ.
RETURN
ENTER
END
Page 40
Component
Video System
Auto
PAL
Page 41
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Video Setup
Page 41
0 IRE
7.5 IRE
Dynamic Range
Page 41
Auto
Standard
Enhanced
Signal Info :
Page 41
-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Main menu
SCR-ADJ
Sub menu
Resize
“SCR-ADJ” menu
Page 42
Page 42
H-Image Shift
Page 42
Picture
SCR-ADJ
Normal
0
0
PRJ-ADJ
SIG-ADJ
Resize
–
30
30
+30
+30
H-Image Shift
V-Image Shift
Overscan
Auto V-Keystone
Keystone Mode
H-Keystone
V-Keystone
Sphere
V-Image Shift
Page 42
Overscan
Page 42
Auto V-Keystone
Page 43
Keystone Mode
Page 43
–
On
On
Off
Keystone
0
0
0
0
Rotation
Keystone
Sphere
Rotation
OSD Display
OSD Brightness
Background
Menu Position
PRJ Mode
On
Standard
Logo
Upper Left
Front
H-Keystone
–60
+60
Page 43
Language
English
V-Keystone
–
100
+100
Page 43
Sphere
Page 43
Rotation
SEL./ADJ.
RETURN
ENTER
END
Page 44
OSD Display
Page 44
On
Off
OSD Brightness
Standard
Level 1
Level 2
Page 44
Background
Logo
Blue
None
Page 44
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Page 44
PRJ Mode
Front
Ceiling + Front
Rear
Ceiling + Rear
Page 44
Language
English
polski
Magyar
Türkçe
Deutsch
Español
Nederlands
Français
Italiano
Page 44
Svenska
Português
Main menu
PRJ-ADJ
Sub menu
Auto Power Off
“PRJ-ADJ” menu
On
Off
Picture
SCR-ADJ
PRJ-ADJ
Page 45
SIG-ADJ
Page 45
Auto Power Off
Economy Mode
One Touch Play
System Standby
Input Name
Demo Mode
RS-232C
Fan Mode
On
Off
Off
Off
Economy Mode
Page 45
On
Off
One Touch Play
Page 45
On
Off
Off
9600bps
Normal
System Standby
Page 45
On
Off
All Reset
Input Name
Page 46
Demo Mode
Page 46
On
Off
RS-232C
9600bps
38400bps
115200bps
Page 46
Lamp Timer (Life)
X
h
XX min ( XX% )
Fan Mode
Page 46
Normal
High
SEL./ADJ.
RETURN
ENTER
END
All Reset
Page 46
Lamp Timer (Life)
Page 46
-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
Adjustment buttons
('/"/\/|)
MENU button
Adjustment buttons
('/"/\/|)
RETURN button
ENTER button
MENU button
ENTER button
RETURN button
Menu Selections (Adjust-
ments)
• This operation can also be performed by using
the buttons on the projector.
Example: “Picture” menu screen when
COMPONENT is selected for
input mode
1 Press MENU.
• The “Picture” menu screen for the se-
lected input mode is displayed.
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Menu bar
Standard
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
2 Press | or \ to select the menu
screen to adjust on the menu
bar.
Blue
CLR Temp
IRIS1 (Manual)
High Brightness
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
On
Off
SEL./ADJ.
RETURN
ENTER
END
-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
3 Press ' or " to select the item
Standard
0
0
0
0
0
0
0
0
you want to adjust.
(Example: Selecting “Bright”)
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
To adjust the projected
image while viewing it
High Brightness
On
Off
Single-
adjustment
item
Press ENTER.
• The selected adjustment item (e.g.
“Bright”) will be displayed at the bottom
of the screen.
SEL./ADJ.
RETURN
ENTER
END
• When ' or " is pressed, the next
item will be displayed. (e.g. “Bright” is
replaced with “Color” by pressing ".)
Bright
0
Note
• Press RETURN to return to the previ-
ous screen.
4 Press | or \ to adjust the item
selected.
• The adjustment is stored.
• For some menu items, press | to dis-
play its submenu and press ' or "
to select an adjustment item, and then
press ENTER.
5 Press MENU.
• The menu screen will disappear.
-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
Menu operation ⇒ Page 34
Picture
Picture Mode
Contrast
Bright
SCR-ADJ
PRJ-ADJ
SIG-ADJ
Standard
0
0
0
0
0
0
0
0
Color
Tint
Sharp
Red
Blue
CLR Temp
IRIS1 (Manual)
IRIS2 (Auto)
Eco+Quiet
Advanced
Reset
IRIS2 (Auto)
Eco+Quiet
Advanced
Gamma
0
0
C.M.S.1
C.M.S.2
Bright Boost
Film Mode
On
Off
Off
High Brightness
On
Off
Auto
Detail Enhance
Off
Off
DNR
MNR
Reset
SEL./ADJ.
RETURN
ENTER
END
SEL./ADJ.
RETURN
ENTER
END
1Selecting the Picture Mode
This function allows you to select the picture mode that best suits the room brightness and the type of image being
projected.
The main default settings of each item when selecting Picture Mode
Selectable
items
Description
IRIS1
CLR Temp Bright Boost
IRIS2 (Auto) Eco+Quiet
(Manual)
Standard
Natural
Dynamic
Movie1
For standard image
A balanced color image is obtained.
A vivid image is obtained.
For viewing images with the brightness
slightly toned down in a darkened
room
0
0
0
Off
Off
On
Off
High Brightness
High Brightness
High Brightness
High Contrast
On
Off
Off
Off
Off
Off
Off
On
-1
Movie2
Game
For viewing images with the brightness
slightly boosted in a darkened room
Use this when the audio and image
are not synched or when you want to
create a sharper image.
-1
0
Off
On
High Contrast
High Brightness
On
Off
On
Off
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
Note
•You can also press PICTURE MODE on the remote control to select the picture mode. (See page 27.)
•The default settings are subject to change without notice.
2Adjusting the Image
Adjustment items
\ button
For less contrast.
| button
For more contrast.
Contrast
Bright
Color
For less brightness.
For less color intensity.
For more brightness.
For more color intensity.
Tint
Sharp
Red
For making skin tones purplish.
For less sharpness.
For making images less reddish.
For making images less bluish.
For making skin tones greenish.
For more sharpness.
For making images more reddish.
For making images more bluish.
Blue
CLR Temp
For making images slightly more reddish For making images slightly more bluish
(slightly warmer colors). (slightly cooler colors).
-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 34
Correcting Gradation of Video (Gamma Correction)
6
3Switching the Iris Setting
This function controls the quantity of the projected light
and the contrast of the image.
■ IRIS1 (Manual)
When the darker areas of the image become difficult to
see because of the image or the projection environment,
you can correct the gamma setting to make the image
brighter and easier to see.
Selectable items
Description
Selectable items
Description
Provides a brighter gradation.
Standard setting
High Brightness
This mode gives priority to brightness
over contrast.
This mode gives priority to contrast
over brightness.
+2
+1
0
High Contrast
–1
–2
■ IRIS2 (Auto)
This automatically selects the optimal contrast to match
the image.
Provides a darker gradation.
Selectable items
On
Description
This mode gives priority to contrast
with the use of auto adjustment.
7Adjusting the Colors
You can select the color of the projected image to correct
and then adjust it to the desired color by setting “Hue”,
“Saturation”, “Value”, and “Effect”.
Off
This mode gives priority to brightness
without the use of auto adjustment.
Note
Note
•You can also use IRIS 1, 2 on the remote con-
trol to change the Iris. (See page 28.)
•Before performing this adjustment, prepare the
image to be adjusted.
•You can perform this adjustment easier in the
still image than in the moving image.
4Eco+Quiet
Select “C.M.S.1” or “C.M.S.2”
(C.M.S.: Color Management Sys-
tem) in the “Advanced” menu, and
press ENTER.
•If there is no data for the stored corrected
color, the color selection screen and the
picker is displayed. (Go to step 2.)
Selectable items Brightness and Power consumption
On
Off
Approx. 75%
100%
Note
•When “Eco+Quiet” is set to “On”, the power
consumption will decrease and the lamp life
will extend. (Projection brightness decreases
approximately 25%.)
Picker
5Using the Advanced
“Advanced” allows you to make even finer adjustments
to the image so that it appears just the way you want
it to.
To display the Advanced menu, select “Advanced” and
press ENTER.
Note
•When the “Advanced” settings are displayed,
select “Advanced” again and press ENTER to
return to the “Picture” menu.
-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation ⇒ Page 34
Set or adjust each item in the C.M.S.
color adjustment screen.
•If there is data for the stored corrected
color, the C.M.S. color adjustment screen
is displayed. (Go to step 3.)
3
C.M.S.1
Select Color
Hue
Saturation
Value
0
0
0
0
C.M.S.1
Select Color
Effect
Hue
Saturation
Value
0
0
0
0
C.M.S.1
Reset
Return
On
Effect
C.M.S.1
Reset
On
Return
SEL./ADJ.
RETURN
ENTER
END
SEL./ADJ.
RETURN
ENTER
END
C.M.S. color adjustment screen:
Selectable items
Description
Select Color
Starts over the selection of the
color to be corrected.
Use the picker and select the color
of the projected image to correct.
The picker can be operated by ad-
justment buttons (P/R/O/Q) on the
Hue
Sets the hue of the main colors.
Saturation
Sets the saturation of the main
colors.
remote control.
Value
Effect*1
C.M.S.1*2
(or C.M.S.2)
Sets the value of the main colors.
Specifies the range of color correction.
•By enlarging the projected image using
or
MAGNIFY, more fine adjustment can
Checks the appearance of the
projected image after above
correction.
be performed.
Reset
Sets “Hue”, “Saturation”, “Value”,
and “Effect” to their default values.
Picker
Return
Completes the correction and closes
the C.M.S. color adjustment screen.
*1 To specify the range of color correction, select
“Effect” and press Oor Qbutton.
Obutton
Specifies smaller range.
Specifies larger range.
Qbutton
*2 To check the appearance of the projected image,
select “C.M.S.1” (or “C.M.S.2”) and set to “On”
or “Off”.
•By continuing to press the adjustment
buttons (P/R/O/Q), the picker moves
rapidly.
On
The appearance of the projected
image after above color adjustment
reflected can be checked.
After selecting the color of the projected
image to correct, press ENTER. The
C.M.S. color adjustment screen is
displayed. (Go to step 3.)
Off
The appearance of the projected
image in former color adjustment
can be checked.
To complete the C.M.S. color
adjustment, select “Return” and
press ENTER.
Note
•The C.M.S. color adjustment can be made to
one color each in “C.M.S.1” and “C.M.S.2”.
-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 34
8Adjusting the Bright Boost
w
Mosquito Noise Reduction (MNR)
Bright Boost uses Texas Instruments’ Bright Boost
technology. The image becomes brighter while the color
reproduction is kept at a high level.
The so-called Mosquito Noise (flickering) can be
reduced.
Selectable items
Off
Description
Selectable items
On
Off
Description
MNR does not function.
The Bright Boost function is activated.
The Bright Boost function is not activated.
Level 1
Level 2
Level 3
Sets the MNR level for viewing a clear-
er picture.
9Selecting the Film Mode
This function provides high-quality playback of
images originally projected at 24 fps, such as movies
on DVDs.
Note
Set “MNR” to “Off” in the following cases:
•When the image is blurry.
•
When the contours and colors of moving images
drag.
Selectable items
Description
Films are detected automatically.
Films are not detected.
Auto
Off
•When TV broadcasts with weak signals are pro-
jected.
•This function can be set when the input signal
is 480I/480P, 576I/576P, S-VIDEO or VIDEO.
0Setting Detail Enhancement
This function enhances the details in images and,
thereby, creates a greater sense of depth.
eResetting All Adjustment Items
To reset all adjustment items to the default settings,
Provides less detail enhancement.
Provides more detail enhancement.
\ button
| button
select “Reset” and press ENTER.
ｑReducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high quality
images with minimal dot crawl and cross color noise.
Selectable items
Off
Description
The DNR function is not activated.
Level 1
Level 2
Level 3
Sets the DNR level for viewing a clear-
er picture.
Note
Set “DNR” to “Off” in the following cases:
•When the image is blurry.
•
When the contours and colors of moving images
drag.
•When TV broadcasts with weak signals are pro-
jected.
•This function can be set when the input signal
is 480I/480P, 576I/576P, S-VIDEO or VIDEO.
-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“SIG-ADJ” Menu)
Menu operation ⇒ Page 34
The illustration shown here is for explanation and may
be different from the actual on-screen display.
Note
Picture
Clock
Phase
H-Pos
V-Pos
SCR-ADJ
PRJ-ADJ
SIG-ADJ
•
Avoid displaying computer patterns which repeat
every other line (horizontal stripes). (Flickering
may occur, making the image hard to see.)
•Information on the currently selected input
signal can be confirmed in item 8 on page 41.
0
0
0
0
Reset
Resolution
Auto Sync
On
*1
*2
Signal Type
Video System
Video Setup
Auto
Auto
0 IRE
Auto
3
Auto Sync (Auto Sync Adjustment)
Dynamic Range
Signal Info : 1080P
Selectable items
On
Description
H : XX.X
kHz/
V : XX.X Hz
Auto Sync adjustment will occur when
the projector is turned on or when
the input signals are switched, when
connected to a computer.
SEL./ADJ.
RETURN
ENTER
END
*1 If the input mode is S-VIDEO or VIDEO input, the display
changes to the “Video System” screen.
*2 Displayed when the input mode is HDMI input.
Off
Auto Sync adjustment is not
automatically performed.
1Adjusting the Computer Image
Note
Use the SIG-ADJ function in case of irregularities such as
vertical stripes or flickering in portions of the screen.
•Auto Sync adjustment is also performed by
pressing AUTO SYNC on the remote control.
•When setting “Auto Sync” to “Off”, and if
AUTO SYNC is pressed, Auto Sync will be ex-
ecuted in “On” mode. If the button is pressed
again within one minute, Auto Sync will be
executed in “On” mode.
•The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
Selectable items
Clock
Description
Adjusts vertical noise.
Phase
Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
•
When the optimum image cannot be achieved with
Auto Sync adjustment, use manual adjustments.
Note
•You can automatically adjust the computer
image by setting “Auto Sync” in the “SIG-ADJ”
menu to “On”, or pressing AUTO SYNC on the
remote control.
•Depending on the type of input signal, the
adjustment range for each setting may vary or
the adjustment may not be available at all.
•To reset all adjustment items, select “Reset”
and press ENTER.
4Signal Type Setting
When using an input mode of HDMI1, HDMI2, or COM-
PUTER, set the signal type to the corresponding input
signal type (RGB or Component).
Selectable items
Description
Auto
Automatically selects the appropriate
input signal between RGB and Com-
ponent.
RGB
Component
Set when RGB signals are received.
Set when component signals are re-
ceived.
2Setting the Resolution
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. How-
ever, for some signals, the optimal resolution mode in
“Resolution” in the “SIG-ADJ” menu may need to be
selected to match the computer display mode.
-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 34
5Setting the Video System
7Adjusting the Dynamic Range
The video input system mode is factory preset to “Auto”;
however, a clear picture from the connected audio-visual
equipment may not be received, depending on the video
signal difference. In that case, switch the video signal.
An optimum picture may not be displayed if an HDMI-
capable device’s output signal type and the projector’s
input signal type do not match. If this should occur,
switch “Dynamic Range”.
Selectable items
Auto
PAL
Selectable items
Description
Auto
In most circumstances, “Auto” should
be selected.
Standard
Enhanced
When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.
SECAM
*NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
8Signal Info
Input signal information is displayed.
* When reproducing NTSC signals in PAL video equip-
ment.
Note
•The video signal can only be set in VIDEO or
S-VIDEO mode.
• When “Video System” is set to “Auto”, you
may not receive a clear picture due to signal
differences. Should this occur, switch to the
video system of the source signal.
6Setting the Video Setup
Selectable items
0 IRE
7.5 IRE
Description
Sets the black level to 0 IRE.
Sets the black level to 7.5 IRE.
Note
•This can be used for a 480I signal connected to
the COMPONENT terminal or the COMPUTER/
COMPONENT terminal.
•This can be used for an NTSC3.58 signal con-
nected to the VIDEO or S-VIDEO terminal.
-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation ⇒ Page 34
The illustration shown here is for explanation and may
be different from the actual on-screen display.
■ V-Image Shift
Selectable items
\ button
| button
Picture
SCR-ADJ
Normal
PRJ-ADJ
SIG-ADJ
V-Image Shift
Downward
Upward
Resize
H-Image Shift
V-Image Shift
Overscan
0
0
On
Auto V-Keystone
Keystone Mode
H-Keystone
V-Keystone
Sphere
Keystone
0
0
0
0
Rotation
\ button
| button
OSD Display
OSD Brightness
Background
Menu Position
PRJ Mode
On
Standard
Logo
Upper Left
Front
Language
English
SEL./ADJ.
RETURN
ENTER
END
Note
•Depending on the Resize mode, Picture mode
or the input signal resolution, the range of the
image shift may be limited.
1Setting the Resize Mode
Note
3Adjusting the Overscan
This function allows you to adjust the Overscan area
(display area).
•For details of the Resize mode, see page 29.
•You can also press RESIZE on the remote
control to set the resize mode. (See page 29.)
Selectable items
Description
The input area is displayed without screen
edges.
The whole input area is displayed.
On
Off
2Adjusting the Image Position
You can move the projected image horizontally or verti-
cally.
■ H-Image Shift
Selectable items
Note
\ button
| button
•You can adjust the Overscan area for the fol-
lowing input signals and the RESIZE function.
- Input signal: 480I/480P, 540P, 576I/576P,
720P, 1035I or 1080I/1080P
- RESIZE function:“NORMAL”, “STRETCH”,
“CINEMA ZOOM” or “ZOOM 14:9”
H-Image Shift
Leftward
Rightward
•If the display area ratio is set too large, noise
may appear at the screen edges. If this hap-
pens, set the display area ratio to a smaller
value.
\ button
| button
•Also read “About Copyrights” on page 30.
-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation ⇒ Page 34
Select “Keystone Mode” in the “SCR-ADJ” menu
and press ENTER. Then select a desired item among
“Keystone”, “Sphere”, or “Rotation” and press ENTER.
“Keystone” has been set as a default setting in which
you can adjust “H-Keystone” and “V-Keystone”.
4Auto V-Keystone Correction
Select “Auto V-Keystone” in the “SCR-ADJ” menu and
press ENTER. Vertical keystone correction is performed
automatically.
■ Keystone
H-Keystone:
Note
Makes the upper and lower
sides parallel.
O or Q
•Pressing ENTER when the on-screen display
of the Auto V-Keystone “On” appears changes
the setting of the Auto V-Keystone to “Off”.
•For details of Keystone mode, see page 24.
•Pressing AUTO V-KEYSTONE while adjusting
the image using Sphere/Rotation Correction
changes Sphere/Rotation Correction mode to
keystone mode.
Horizontal Keystone Correction
Auto V-Keystone Correction
V-Keystone:
Makes the left and right sides
parallel.
O or Q
Vertical Keystone Correction
5Keystone Mode Correction
This function can correct distortion of an image projected
toward a spherical or cylindrical screen as well as trap-
ezoidal distortion of an image on a flat screen and rotate
the image at your arbitrary angle.
■ Sphere
This function corrects screen distortion created during
spherical or cylindrical screen projection.
O button
Narrower at the center
Wider at the center
Note
•For details of Keystone mode, see page 24.
Q button
Sphere Correction
Info
Correction of Convex Distortion:
Correction of Concave Distortion:
•While adjusting the image using Keystone/
Sphere/Rotation Correction, straight lines
and the edges of the image may appear
jagged.
-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)
Menu operation ⇒ Page 34
■ Rotation
0Reversing/Inverting
This function can rotate the image at an arbitrary
Projected Images
angle.
This function allows the projector to be used in a wider
range of projection styles by allowing the image to be
inverted to suit the projection environment (location).
Rotates the image
counterclockwise.
O button
Q button
Rotate the image clockwise.
Selectable items
Description
Rotation Correction
Front
Normal image (Projected from the
front of the screen)
Ceiling + Front
Inverted image (Projected from the
front of the screen with an inverted
projector)
Rear
Reversed image (Projected from the
rear of the screen or with a mirror)
Ceiling + Rear
Reversed and inverted image (Pro-
jected with a mirror)
6Setting On-screen Display
See page 16 for details of Projection (PRJ) Mode.
Selectable items
On
Off
Description
All on-screen displays are displayed.
INPUT/FREEZE/AUTO SYNC/RESIZE/
PICTURE MODE/ECO+QUIET/
MAGNIFY/ “An invalid button has been
pressed.” are not displayed.
qSelecting the On-screen Display
Language
The projector can switch the on-screen display language
among 17 languages.
7Setting the Brightness of the
English
Menu Screen
Deutsch
Español
Nederlands
Français
Italiano
Sets the brightness of the menu screen.
Selectable items
Standard
Description
Standard brightness
Level 1
Darker than the “Standard”
brightness
Svenska
Português
Level 2
Darker than the “Level 1” brightness
polski
Magyar
Türkçe
8
Selecting the Background Image
Selectable items
Description
SHARP logo screen
Blue screen
Logo
Blue
None
— (Black screen)
9Selecting the Menu Screen
Position
Select “Menu Position” in the “SCR-ADJ” menu and the
desired position for the menu screen.
Selectable items
Center
Upper Right
Lower Right
Upper Left
Description
Displayed on the center of the image.
Displayed on the upper right of the image.
Displayed on the lower right of the image.
Displayed on the upper left of the image.
Displayed on the lower left of the image.
Lower Left
-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ” Menu)
Menu operation ⇒ Page 34
The illustration shown here is for explanation and may
be different from the actual on-screen display.
3Setting One Touch Play, System
Standby and Input Name
Picture
SCR-ADJ
On
PRJ-ADJ
SIG-ADJ
Auto Power Off
Economy Mode
One Touch Play
System Standby
Input Name
When a Sharp product equipped with Consumer Elec-
tronics Control (HDMI CEC) is connected to the projector
with an HDMI cable, you can use the linked function with
HDMI CEC (“One Touch Play” and “System Standby”).
Off
Off
Off
Demo Mode
RS-232C
Fan Mode
Off
9600bps
Normal
All Reset
Note
The CEC function may not work with some CEC
devices. (When the projector is connected to a non-
Sharp product, the CEC function may not work.)
Lamp Timer (Life)
X
h
XX min
(
XX% )
■ Setting the One-Touch Playback Function
SEL./ADJ.
RETURN
ENTER
END
(One Touch Play)
One Touch Play turns on the projector and selects the
input automatically when you turn on or begin playback
on connected HDMI-compliant Sharp Video Products.
1Setting Auto Power Off Mode
Selectable items
On
Off
Description
This function automatically switches the projector to
Standby mode if no signals are received for a set period.
This enables One Touch Play.
This disables One Touch Play.
Selectable items
On
Description
When no input signal is detected for
more than 15 minutes, the projector
will automatically enter standby mode.
Note
Off
The Auto Power Off function will be
disabled.
•
When enabling One Touch Play, be sure to enable
the CEC setting on the HDMI-compliant Sharp
Video Products connected to the projector.
The Economy mode is set to “Off” when One
Touch Play is set to “On”.
In the following cases, One Touch Play is not
enabled.
- When playback is paused
- When the screen is turned off (black) after the
lens shutter is closed
•
•
Note
•When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
- When the cooling fan is running (See page
48.)
- When the lamp is warming up (See page 48.)
2Setting the Power Save Mode
■ Setting the System Standby Function
(Economy Mode)
(System Standby)
When you turn off the projector, the HDMI-compliant
video equipment connected to the projector enters
standby mode.
■ Economy Mode
Selectable items
On
Off
Description
This enables the Economy mode.
Selectable items
On
Off
Description
You can use the linked functions. RS-
232C can be used to control the pro-
jector in standby mode.
This enables System Standby.
This disables System Standby.
Note
Note
•When enabling System Standby, be sure to
enable the CEC setting on the HDMI-compliant
Sharp Video Products connected to the
projector.
•
Set this function to “Off” when you want to use
RS-232C to control the projector from a computer.
•One Touch Play is set to “Off” when the
Economy mode is set to “On”.
-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ-ADJ” Menu) (Continued)
Menu operation ⇒ Page 34
■ Setting the Input Terminal Names (Input
5Selecting the Transmission
Name)
Speed (RS-232C)
Set the name of the input terminal (up to 14 alphanu-
merical characters).
Make sure that both the projector and computer are set
for the same baud rate.
Press P/R to select “Input Name”
Selectable items
Description
and then press ENTER.
9600bps
Transmission speed is slow.
Picture
SCR-ADJ
PRJ-ADJ
SIG-ADJ
HDMI1
38400bps
Input name
H D M I 1
115200bps
Transmission speed is rapid.
Reset
Return
6Fan Mode Setting
This function changes the fan rotation speed.
\ or | button
▼ or 、 button
ENTER button
Selects a character column.
Selects a character.
Selectable items
Normal
High
Description
Suitable for normal environments.
Sets the input terminal name.
Select this when using the projector at
altitudes of approximately 4,900 feet
(1,500 meters) or more.
Press P/R to select “Return” and
then press ENTER to return to the
previous screen.
•To return to the previous setting, select
“Reset” and then press ENTER.
• When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
7
Returning to the Default Settings
Use “All Reset” to initialize all the adjustments you have
made to the default settings.
Note
•
When connecting the projector to a Sharp Video
Product with an HDMI cable using an input
mode of HDMI1 or HDMI2 and the linked func-
tion with HDMI CEC (“One Touch Play” or “Sys-
tem Standby”) works normally, the name of the
connected Sharp Video Product is automatically
captured.
Note
The following items cannot be initialized.
•“SIG-ADJ” menu — Resolution
•“SCR-ADJ” menu — Language
•“PRJ-ADJ” menu — Lamp Timer (Life)
•
•
When the input terminal name has been changed
by a user, the changed name is displayed.
To return to the default name, select “Reset”
and press ENTER.
8
Lamp Timer (Life)
You can confirm the cumulative lamp usage time and the
remaining lamp life (percentage).
Lamp usage condition
Remaining lamp life
100% 5%
Approx. 3,000 Approx. 150
hours hours
Approx. 2,000 Approx. 100
hours hours
4
Setting the Demo Mode
“Life”
Operated exclusively with
“Eco+Quiet” set to “On”
Set the Demo Mode to “On” or “Off”.
Selectable items Description
On
Operated exclusively with
“Eco+Quiet” set to “Off”
This enables Demo Mode.
This disables Demo Mode.
Off
Note
•It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
•The lamp life may vary depending on the us-
age condition.
-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the lens
Cleaning the projector
■ Ensure that you have unplugged the power cord
before cleaning the projector.
■ The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on
the projector.
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coating
film on the surface of the lens.
■ As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.
■ Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Info
Thinner
Wax
• If you want to clean the air vents during projector
operation, ensure you press STANDBY/ON on
the projector or STANDBY on the remote control
and put the projector into standby mode. After
the cooling fan has stopped, clean the vents.
-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector
indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and
the projector will enter standby mode. After the projector has entered standby mode, follow the procedures
given below.
Top View
Power indicator
Lamp indicator
Temperature warning
indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking.
If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter
standby mode. When you find the temperature warning indicator blinking, be sure to perform the measures
described on page 49.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on
the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off
and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate
in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not
turn on.
Indicators on the Projector
Power indicator
Red on
Normal (Standby)
Green on
Red blinks
Green blinks
Normal (Power on)
Abnormal (See page 49.)
Normal (Cooling)
Green and orange blink
alternately
The lens shutter is closed. (See page 22.)
Lamp indicator
Green on
Green blinks
Red on
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be changed. (See
page 49.)
Temperature warning Off
indicator
Normal
Red on/Red blinks
The internal temperature is abnormally high. (See page 49.)
-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible Solution
Normal
Abnormal
Temperature
warning
indicator
Off
Red blinks The internal
• Temperatures
around the
projector are
high.
• Use the projector in an area with a
temperature of lower than 95°F (+35ºC).
• Relocate the projector to an area with
proper ventilation. (See page 6.)
(On)/
Red on
temperature is
abnormally
(Standby) high.
• Blocked air
intake
• Cooling fan
breakdown
• Internal circuit
failure
• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for repair.
• Clogged air
intake
Lamp
indicator
Green on
(Green
blinks when
the lamp is
warming up.)
Red on
Red on
The lamp does • The lamp is shut • Disconnect the power cord from the AC
not illuminate.
down
abnormally.
outlet, and then connect it again.
Time to change • Remaining lamp • Carefully replace the lamp. (See page
the lamp.
life becomes 5%
or less.
50.)
• Take the projector to your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for repair.
• Please exercise care when replacing the
lamp.
The lamp does • Burnt-out lamp
(Standby) not illuminate.
• Lamp circuit
failure
• Securely install the cover.
Power
indicator
Green on/
Red on
Green blinks
(Cooling)
Red blinks The power
indicator blinks
• The lamp unit
cover is open.
• If the power indicator blinks in red even
when the lamp unit cover are securely
installed, contact your nearest Sharp
Authorized Projector Dealer or Service
Center (see page 60) for advice.
in red when the
projector is on.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the pos-
sible solutions above and then wait until the projector has cooled down completely before plugging in the
power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may
change and this is not a malfunction.
-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp
life (percentage) can be checked with the on-screen display. (See page 46.)
■ Purchase a replacement lamp of type AN-K15LP from your place of purchase, nearest Sharp Autho-
rized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
U.S.A. ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
■ The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projec-
tor. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer
or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mer-
cury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. * If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the Lamp Unit
• Do not remove the lamp unit from the projector right after use. The lamp and parts
Warning!
around the lamp will be very hot and may cause burns or injury.
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
Optional
accessory
Lamp unit
AN-K15LP
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
STANDBY/ON button
Press STANDBY/ON on the
1
projector or STANDBY on the
remote control to put the projec-
tor into standby mode.
AC socket
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
2
• Leave the lamp until it has fully cooled
down (about 1 hour).
Remove the lamp unit cover.
3
• Close the lens shutter. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
2
1
User service screw
(for lamp unit cover)
-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp (Continued)
Securing screws
Remove the lamp unit.
4
• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
5
Replace the lamp unit cover.
6
• Align the tab on the lamp unit cover
(1) and place it while pressing the cover
(2) to close it. Then tighten the user
service screw (3) to secure the lamp
unit cover.
Info
1
• If the lamp unit and lamp unit cover are
not correctly installed, the power will
not turn on, even if the power cord is
connected to the projector.
2
3
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this
may cause the lamp to become damaged
or explode.
AC socket
Lamp indicator
STANDBY/
ON button
1 Connect the power cord and
ENTER
button
open the lens shutter fully.
• Plug the power cord into the AC socket
of the projector.
R
button
MENU button
2 Reset the lamp timer.
•
While simultaneously holding down
MENU, ENTER and R on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000 H” is displayed, indicating
that the lamp timer is reset.
-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals :
mini D-sub 15 pin female connector
COMPUTER Input/Output
Pin No. Signal
COMPONENT Input/Output
Pin No. Signal
15
11
1
Video input (red)
1
PR (CR)
2
3
4
5
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
2
3
4
5
Y
PB (CB)
Not connected
Not connected
Earth (PR)
6
6
1
6
5
10
7
8
Earth (green/sync on green)
Earth (blue)
7
8
Earth (Y)
Earth (PB)
9
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
9
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
10
11
12
13
14
15
10
11
12
13
14
15
RS-232C Terminal: 9-pin D-sub male connector
Pin No. Signal Name
I/O
Reference
1
Not connected
9 8 7 6
2
3
4
5
6
7
8
9
RD
SD
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Input
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
SG
Reserved
Reserved
5 4 3 2 1
HDMI Terminal
Pin No. Name
Pin No. Name
Pin No. Name
18
2
1
2
3
4
5
6
7
T.M.D.S data 2+
T.M.D.S data 2 shield
8
T.M.D.S data 0 shield
T.M.D.S data 0–
T.M.D.S clock+
T.M.D.S clock shield
T.M.D.S clock–
CEC
14
15
16
17
18
19
Reserved
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
9
T.M.D.S data 2–
T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1–
T.M.D.S data 0+
10
11
12
13
19
1
-53
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 21 for connection.)
Communication conditions
Set the serial port settings of the computer as follows.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
*Use the same settings for the projector and computer.
Basic format
Send commands from the computer in the following order: command, parameter, and return code. After
processing the command from the computer, the projector sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
O
K
E
R
R
Return code (0DH)
Return code (0DH)
Info
• If you are controlling the projector from a computer using RS-232C commands, wait at least 30 seconds
after turning the projector on before sending any commands.
• When more than one code is being sent, send each command only after the response code for the previ-
ous command from the projector is verified.
• When using the computer control function of the projector, the projector’s operating status cannot be read
by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display. If the projector receives a command other than a
menu display command, it will execute the command without displaying the on-screen display.
Commands
Example: To turn on the projector
Computer
Projector
→
←
P
O
W
R
1
O
K
_
_
_
Return
Control Contents
Command
Parameter
Standby mode
(or 30-second startup time)
Power ON
Power
On
P
P
T
T
O
O
L
W
W
P
R
R
S
N
_
_
?
_
_
_
?
_
_
_
?
_
1
0
?
1
OK or ERR
OK
Off
OK
1
OK or ERR
Status
0
Projector Condition
A
B
0:Normal
0:Normal
1:Temp High
1:Temp High
2:Fan Error
4:Lamp Cover Open
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
64:Temp Abnormally High
8:Lamp Life 5% or less
16:Lamp Burnt-out
32:Lamp Ignition Failure
Lamp
Status
T
L
P
S
_
_
_
1
0:Off, 1:On, 2:Retry
3:Waiting, 4:Lamp Error
0:Off, 4:Lamp Error
Power Status
T
T
T
T
T
T
M
P
P
P
P
P
L
L
L
L
N
N
J
J
J
J
O
P
T
W
N
T
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
1
1
1
1
1
1
1
*
1:On, 2:Cooling
1
0:Standby
Quantity
Usage Time (Hour)
Usage Time (Minuite)
Life (Percentage)
Model Name Check
Model Name Check
0-9999 (Integer)
0, 15, 30, 45
0%-100% (Integer)
XVZ15000
T
M
L
T
Name
A
R
N
N
N
N
M
D
1
XV-Z15000
OK or ERR
Projector Name Setting1 (First 4 characters) *1
Projector Name Setting2 (Middle 4 characters) *1
Projector Name Setting3 (Last 4 characters) *1
Projector Name Check
2
*
*
*
*
OK or ERR
3
*
*
*
*
OK or ERR
0
_
_
_
1
Projector Name
-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Return
Control Contents
Computer
Command
Parameter
Standby mode
(or 30-second startup time)
Power ON
Input Change
I
I
I
I
I
I
I
R
R
R
R
V
V
R
G
B
B
B
B
D
D
B
_
_
_
_
_
_
?
_
_
_
_
_
_
?
_
_
_
_
_
_
?
1
2
3
4
1
2
?
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
Component
HDMI1
G
G
G
E
ERR
ERR
ERR
ERR
ERR
ERR
HDMI2
S-Video
Video
E
Input RGB Check
G
1: Computer, 2: Component,
3: HDMI1, 4: HDMI2, ERR
1: S-Video, 2: Video, ERR
1: RGB, 2: Video
Input Video Check
Input Mode Check
Input Check
I
I
I
V
M
C
E
O
H
D
D
K
?
?
?
?
?
?
?
?
?
?
?
?
ERR
ERR
ERR
1: Computer
2: Component
3: HDMI1
4: HDMI2
5: S-Video
6: Video
Resize
Computer
Component
HDMI1
Normal
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
D
D
D
D
D
D
A
A
A
A
A
B
B
B
B
B
L
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
V
V
E
S
S
S
S
S
S
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
1
2
3
5
7
6
1
2
3
5
7
6
1
2
3
5
7
6
1
2
3
5
7
6
1
2
5
7
6
1
2
5
7
6
1
1
2
3
4
5
6
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Stretch
Dot By Dot
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
Stretch
Dot By Dot
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
Stretch
Dot By Dot
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
HDMI2
Stretch
Dot By Dot
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
S-Video
Video
Stretch
Cinema Zoom
Zoom14:9
Smart Zoom
Normal
Stretch
Cinema Zoom
Zoom14:9
Smart Zoom
ALL Reset
Computer INPUT
Picture Mode
Standard
Natural
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
Component INPUT
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
_
_
*
*
_
1
-55
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands (Continued)
Return
Control Contents
Picture Mode
Command
Parameter
Standby mode
Power ON
(or 30-second startup time)
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
HDMI1
Standard
Natural
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
T
T
L
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
F
P
S
S
S
S
S
S
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
_
_
_
_
_
_
*
_
_
_
_
_
_
*
1
2
3
4
5
6
*
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
P
P
P
P
P
P
P
B
C
T
S
R
B
C
R
R
R
R
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
HDMI2
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
S-Video INPUT
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
S
S
S
S
S
S
I
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Picture Mode
_
_
_
_
_
_
_
_
*
*
*
_
_
_
_
_
_
_
*
1
1
2
3
4
5
6
*
Video INPUT
Standard
Natural
Dynamic
Movie1
Movie2
Game
Contrast
Bright
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-30 - +30
-2-+2
R
O
I
*
*
*
Color
*
*
*
Tint
*
*
*
Sharp
H
D
E
T
E
Q
Q
E
*
*
*
Red
*
*
*
Blue
*
*
*
CLR Temp
Picture Reset
Horizontal
Vertical
_
_
_
_
0
*
*
_
_
_
0
1
1
2
1
RGB Frequency Check
Lamp Timer Reset *2
kHz (***.* or ERR)
Hz (***.* or ERR)
ERR
F
P
OK, ERR
Note
•If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
*1 For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3.
*2 The Lamp Timer Reset command can only be sent in standby mode.
-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15–110 kHz, Vertical Frequency: 43–85 Hz, Pixel Clock: 12–170 MHz
• Compatible with sync on green and composite sync signals (TTL level)
Horizontal frequency
[kHz]
Vertical
frequency[Hz]
Analog
Support
Digital
Support
PC/MAC
Mode
Resolution
Display
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
47.7
47.8
55.9
55.0
66.2
67.5
60.0
64.0
64.0
65.3
55.9
65.3
66.8
60
70
85
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
60
60
60
60
70
75
60
60
60
60
60
60
60
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
640 × 400
720 × 400
640 × 480
✔
✔
VGA
✔
✔
✔
✔
SVGA
XGA
800 × 600
1024 × 768
✔
✔
Upscale
✔
✔
✔
PC
1280 × 720
1280 × 768
1280 × 800
1360 × 768
1366 × 768
1440 × 900
✔
WXGA
WXGA+
SXGA
✔
1152 × 864
✔
✔
✔
✔
✔
✔
1280 × 960
1280 × 1024
SXGA+
1400 × 1050
1600 × 900
1680 × 1050
1920 × 1080
*
1
WSXGA+
Down sampled
Intelligent
Compression
2
1920 × 1080
*
67.5
60
✔
✔
MAC 13"
MAC 16"
MAC 19"
MAC 21"
VGA
SVGA
XGA
640 × 480
832 × 624
1024 × 768
1152 × 870
34.9
49.7
60.2
68.7
67
75
75
75
✔
✔
✔
✔
Upscale
SXGA
*1 When a 1920 × 1080 analog signal is input, the image is compressed before it is displayed on the screen.
*2 Full image display when “Resolution” is set to “1920 × 1080”
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
•When “Screen resolution” of the computer is different from the resolution displayed on the projected im-
age, follow the procedures shown below.
–Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in “Screen
resolution” of the computer.
–Depending on the computer you are using, the output signal may not be faithful to the “Screen reso-
lution” adjustment. Check the settings of the computer's signal output. If the settings cannot be
changed, it is recommended that the resolution be set to “1920 × 1080” or “1280 × 720”.
DTV
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Signal
Signal
15.7
31.5
33.8
15.6
31.3
37.5
45.0
60
60
60
50
50
50
60
✔
✔
✔
✔
✔
✔
✔
28.1
33.8
27.0
28.1
33.8
56.3
67.5
50
60
24
25
30
50
60
✔
✔
✔
✔
✔
✔
✔
✔
✔
480I
480P
540P
576I
1080I
1080I
1080P
1080P
1080P
1080P
1080P
✔
576P
720P
720P
✔
✔
✔
✔
✔
-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The lens shutter is closed.
22
–
22, 27
26, 40, 41
18-22
12
• The selected input mode is wrong.
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook computer.
• The lamp unit cover is not installed correctly.
• The selected “Signal Type” is wrong.
–
No picture or projector does
not start
51, 52
40
•
The video signal format of the video equipment is not set correctly.
41
• “Bright” is set to minimum position.
36
• Image adjustments are incorrectly set.
36
(S-VIDEO or VIDEO input)
• Video input system is incorrectly set.
(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)
• Input signal type is incorrectly set.
41
40
Color is faded or poor.
• Adjust the focus.
23
17
• The projection distance exceeds the focus range.
(Computer input)
• Perform “SIG-ADJ” Adjustments (“Clock” Adjustment)
• Perform “SIG-ADJ” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
40
40
–
• The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Reduc-
tion) setting is not correct.
39
Picture is blurred;
noise appears.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Please set up the projector at
least one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
–
An unusual sound is
occasionally heard
from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused
by a room temperature changes. This will not affect operation or perfor-
mance.
–
Maintenance
indicator on the
projector illuminates.
• See “Maintenance Indicators”.
48
40
Picture is green when receiving
component signals and the video
equipment is connected to the
COMPONENT or COMPUTER/
COMPONENT terminal on the
projector.
• Change the input signal type setting.
Picture is pink when receiv-
ing RGB signals and the video
equipment is connected to the
COMPONENT or COMPUTER/
COMPONENT terminal on the
projector.
The black levels of the
image show banding or
appear faded when HDMI1
or 2 is selected.
• Make adjustments that result in the best picture quality in the “Dynamic
41
36
Range” setting.
Picture is too bright and
whitish.
• Image adjustments are incorrectly set.
-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Page
The cooling fan
becomes noisy.
• When temperature inside the projector increases, the cooling fan runs
faster.
–
The lamp does not light up
even after the
• The lamp indicator is illuminating in red.
Replace the lamp.
22, 48, 51
projector turns on.
• The lens shutter is opened fully.
The lamp suddenly turns off
during projection.
The image sometimes
flickers.
• Cables are incorrectly connected to the projector or the connected equip-
ment works improperly.
• If this happens frequently, replace the lamp.
18-21
51
The lamp needs much time
to turn on.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
51
Picture is dark.
One Touch Play is not
enabled.
• Non-Sharp Video Products are connected.
One Touch Play function may not work when the projector is connected
to non-Sharp Video Products.
45
19
• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
One Touch Play function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.
• One Touch Play function of the projector is not set to “On”.
45
–
• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.
• One Touch Play is set to “Off” and disabled when the Economy mode is
45
45
set to “On”.
System Standby is not
enabled.
• Non-Sharp Video Products are connected.
System Standby function may not work when the projector is connected
to non-Sharp Video Products.
• An HDMI cable is not used for connection between the projector and the
Sharp Video Products.
19
System Standby function is enabled when the projector is connected to
the Sharp Video Products with an HDMI cable.
• System Standby function of the projector is not set to “On”.
45
–
• CEC settings of connected Sharp Video Products or other CEC devices
are incorrect.
A response code cannot be
received when the
projector was attempted
to be controlled using
• In the case of transmitting RS-232C commands from a computer during
standby, it takes a maximum of 30 seconds for the computer to receive
the response code. Set the response code waiting time of the computer
to 30 seconds or more.
54
RS-232C commands from
a computer during standby.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the projector’s
remote control sensor, place the projector where it will not be affected by
strong light.
12
12
12
• The batteries may be depleted or inserted incorrectly. Make sure the bat-
teries are inserted correctly or insert new ones.
12
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the unit and plug it in again after more than
5 minutes.
-59
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on pages 58 and 59. If this operation manual does not answer your question, please contact the
SHARP Service departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111
Latin America Sharp Electronics Corp. Latin
American Group
Fax: (09) 573-0112
(305) 264-2277
Singapore
Hong Kong
Taiwan
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Sharp Corporation (Taiwan)
0800-025111
France
Sharp Electronics France
01 49 90 35 40
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
XV-Z15000
0.65" DLP® Chip × 1
Display devices
Resolution
1080P (1920 × 1080)
Lens
F number
Zoom
F 2.5 – 2.7
Manual, ×1.15 (f = 21.0 – 24.2 mm)
Focus
Manual
× 2
Input terminals
HDMI
Computer/Component
(mini D-sub 15 pin)
× 1
Component (3RCA)
S-Video (mini DIN 4 pin)
Video (RCA)
× 1
× 1
× 1
× 1
Control and
communication
terminals
RS-232C (mini D-sub 9 pin)
Projection lamp
Rated voltage
Rated frequency
Input current
250 W
AC 100 – 240V
50/60 Hz
3.7 A
Power consumption (Standby)
353 W (7.6 W) with AC 100 V
339 W (8.3 W) with AC 240 V
Operation temperature
Cabinet
41°F to 95°F (+5°C to +35°C)
Plastic
15 3/4" × 3 15/16" × 13 13/64"
(400 × 100 × 335 mm)
Dimensions (main body only) [W × H × D]
Weight (appprox.)
12.8 lbs. (5.8 kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of produc-
tion units. There may be some deviations from these values in individual units.
-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
4 17/32
(115)
3 23/64
(85)
1/8 (3)
15 3/4 (400)
M4
M4
M4
M4
1 13/16
15/64 (5.75)
(45.75)
7 5/64
4 5/8
2 61/64
(75)
(179.75)
(116.25)
-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Accessories............................................................ 8
AC socket............................................................. 22
Adjustment buttons ............................................. 34
Adjustment feet .................................................... 23
Advanced ............................................................. 37
All Reset ............................................................... 46
Auto Power Off..................................................... 45
Auto Sync............................................................. 40
AUTO SYNC button ............................................. 27
AUTO V-KEYSTONE button................................. 25
MAGNIFY buttons ................................................ 28
MENU HIDE button .............................................. 28
MENU button........................................................ 34
MNR ..................................................................... 39
Movie1, 2.............................................................. 36
Natural.................................................................. 36
ON button............................................................. 22
One Touch Play .................................................... 45
On-screen Display................................................ 44
Optional accessories.............................................. 8
OSD Brightness.................................................... 44
Overscan .............................................................. 42
Background.......................................................... 44
Batteries ............................................................... 12
Bright.................................................................... 36
Bright Boost ......................................................... 39
Phase.................................................................... 40
Picture .................................................................. 36
Picture Mode........................................................ 36
PICTURE MODE button ....................................... 27
Power cord....................................................... 8, 22
Power indicator .............................................. 22, 48
PRJ-ADJ............................................................... 45
PRJ mode....................................................... 16, 44
Carrying handle .................................................... 10
Ceiling-mount setup............................................. 16
CINEMA ZOOM.................................................... 29
Clock .................................................................... 40
CLR Temp (Color Temperature)............................ 36
C.M.S. .................................................................. 37
Color..................................................................... 36
COMPONENT button........................................... 26
COMPONENT terminal......................................... 18
COMPUTER button.............................................. 26
COMPUTER/COMPONENT terminal ............. 18, 20
Contrast................................................................ 36
Remote control..................................................... 11
Remote control sensors ....................................... 12
Replacing the lamp .............................................. 50
RESIZE button...................................................... 29
RETURN button.................................................... 34
Rotation.......................................................... 25, 44
RS-232C............................................................... 46
RS-232C terminal................................................. 21
Detail Enhance ..................................................... 39
DNR...................................................................... 39
DOT BY DOT........................................................ 30
Dynamic ............................................................... 36
Dynamic Range.................................................... 41
Saturation............................................................. 38
SCR-ADJ.............................................................. 42
Screen Size and Projection Distance ................... 17
Security bar .......................................................... 10
Select Color.......................................................... 38
Sharp.................................................................... 36
SIG-ADJ ............................................................... 40
Signal Info............................................................. 41
Signal Type........................................................... 40
SMART ZOOM ..................................................... 30
Sphere............................................................ 25, 43
Standard............................................................... 36
STANDBY button.................................................. 22
STANDBY/ON button ........................................... 22
STRETCH ............................................................. 29
S-VIDEO button.................................................... 26
S-VIDEO terminal ........................................... 18, 19
System Standby................................................... 45
Economy Mode .................................................... 45
ECO+QUIET button.............................................. 28
Effect .................................................................... 38
ENTER button....................................................... 34
Fan Mode ............................................................. 46
Film Mode............................................................. 39
Focus ring............................................................. 23
FREEZE button..................................................... 27
Game.................................................................... 36
Gamma................................................................. 37
HDMI1, 2 buttons................................................. 26
HDMI1, 2 terminals......................................... 18, 19
HEIGHT ADJUST lever......................................... 23
H-Image Shift ................................................. 26, 42
H-Pos ................................................................... 40
Hue....................................................................... 38
Temperature warning indicator............................. 48
Tint........................................................................ 36
IMAGE SHIFT button............................................ 26
INPUT button........................................................ 26
Input Name........................................................... 46
IRIS1, 2................................................................. 37
IRIS1, 2 buttons.................................................... 28
Value..................................................................... 38
VIDEO button ....................................................... 26
Video Setup.......................................................... 41
Video System ....................................................... 41
VIDEO terminal..................................................... 18
V-Image Shift.................................................. 26, 42
V-Pos.................................................................... 40
Kensington Security Standard connector ............ 10
KEYSTONE button ............................................... 24
Lamp indicator ..................................................... 48
Lamp Timer (Life).................................................. 46
Language (on-screen display language) .............. 44
Lens shutter.............................................. 22, 27, 51
ZOOM 14:9........................................................... 30
Zoom ring............................................................. 23
-63
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Printed in China
Imprimé en Chine
Impreso en China
Impresso na China
TINS-E012WJZZ
09P01-CH-NM
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Air Cleaner FP P35CX User Manual
Sony Car Stereo System XR C7200R User Manual
Sony Digital Camera DSC H20 B User Manual
Sony VCR SLV 685HF User Manual
Star Micronics Printer LC 1011C User Manual
Stoelting Freezer F112 User Manual
Sunbeam Griddle CKSBGRFM10 033 User Manual
Sunbeam Slow Cooker HP2200 User Manual
Sylvania Flat Panel Television LC225SC9 User Manual
Tannoy Speaker B225 User Manual