Sharp Projector XG PH70X User Manual

OPERATION MANUAL  
MODEL  
XG-PH70X  
(Standard zoom lens attached)  
XG-PH70X-N  
(No lens attached)  
MULTIMEDIA PROJECTOR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using the projector, please read this operation manual carefully.  
Introduction  
ENGLISH  
There are two important reasons for prompt warranty registration of your new SHARP Projector, using  
the REGISTRATION CARD packed with the projector.  
1. WARRANTY  
This is to assure that you immediately receive the full benefit of the parts, service and labor  
warranty applicable to your purchase.  
2. CONSUMER PRODUCT SAFETY ACT  
To ensure that you will promptly receive any safety notification of inspection, modification, or  
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE  
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.  
U.S.A. ONLY  
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially  
careful that children do not stare directly into the beam of light.  
WARNING: To reduce the risk of fire or electric shock, do not expose this product to  
rain or moisture.  
See bottom of projector.  
The lightning flash with arrowhead symbol,  
within an equilateral triangle, is intended to  
CAUTION  
RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE SCREWS  
EXCEPT SPECIFIED USER  
to constitute a risk or electric shock to  
SERVICE SCREW.  
alert the user to the presence of uninsulated  
“dangerous voltage” within the product’s  
enclosure that may be of sufficient magnitude  
persons.  
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER.  
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
The exclamation point within a triangle is  
intended to alert the user to the presence of  
important operating and maintenance  
(servicing) instructions in the literature  
accompanying the product.  
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not  
expressly approved by the manufacturer could void the user’s authority to operate this equip-  
ment.  
U.S.A. ONLY  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the operation manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference, in which case  
the user will be required to correct the interference at his own expense.  
U.S.A. ONLY  
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device  
complies with FCC Class A verification.  
U.S.A. ONLY  
WARNING:  
This is a Class A product. In a domestic environment this product may cause radio interference in  
which case the user may be required to take adequate measures.  
-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING:  
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.  
During normal operation, when putting the projector into standby mode always use the STANDBY button on the  
projector or on the remote control.  
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.  
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.  
PRODUCT DISPOSAL  
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of  
these materials may be regulated due to environmental considerations. For disposal or recycling information,  
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries  
Alliance: www.eiae.org.  
Caution Concerning Lamp Replacement  
See “Replacing the Lamp” on page 96.  
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 pixels (micromirrors). As  
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there  
are certain acceptable tolerances that the equipment must conform to.  
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture  
screen. This will not affect the picture quality or the life expectancy of the unit.  
DLP® and the DLP logo are registered trademarks of Texas Instruments.  
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or  
other countries.  
PC/AT is a registered trademark of International Business Machines Corporation in the United States.  
Adobe® Reader® is a trademark of Adobe Systems Incorporated.  
Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.  
All other company or product names are trademarks or registered trademarks of their respective compa-  
nies.  
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru-  
ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse as-  
semble or discompile the contents thereof.  
Authorized representative responsible for the European Union Community Market  
SHARP ELECTRONICS (Europe) GmbH  
E.U. ONLY  
Sonninstraße 3, D-20097 Hamburg  
-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to ReadThis Operation Manual  
In this operation manual, the illustrations and on-screen displays are simplified for explana-  
tion.This may differ from the actual on-screen display.  
Using the Menu Screen  
The menu can be operated to achieve two functions, adjustments and settings. (For setting  
the menu items, see pages 58 and 59. )  
Mouse/  
adjustment  
button ('/"/\/|)  
ENTER button  
MENU button  
Buttons used in this  
operation  
MENU button  
ENTER  
Buttons used in this  
operation  
button  
UNDO button  
Adjustment  
buttons ('/"/\/|)  
UNDO button  
Menu Selections (Adjustments)  
Example: Adjusting “Bright”  
Menu item  
This operation can also be performed by using the buttons on the projector.  
Example: “Picture” screen menu for  
INPUT 1 (RGB) mode  
1
2
Press  
.
Button used in  
this step  
The “Picture” menu screen for the se-  
lected input mode is displayed.  
Press \ or | to display the other  
menu items.  
Menu items  
On-screen display  
There are eight menu items as shown  
below.  
Note  
The “Fine Sync” menu is not available  
for selecting INPUT 4 or INPUT 5.  
56  
Info  
...........Indicates safeguards when using the projector.  
........Indicates additional information for setting up and operating the projector.  
Note  
For Future Reference  
Maintenance  
Troubleshooting  
Index  
Page 93  
Pages 102 and 103  
Page 107  
-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Preparing  
Introduction  
How to Read This Operation Manual ............ 3  
Contents.......................................................... 4  
How to Access the PDF Operation Manuals..... 7  
IMPORTANT SAFEGUARDS .......................... 8  
Accessories .................................................. 11  
Part Names and Functions .......................... 13  
Using the Remote Control ........................... 17  
Usable Range .................................................... 17  
Inserting the Batteries ....................................... 17  
Using the Remote Control with a Signal Cable .. 18  
Switching the Remote Control Mode ................. 18  
Using the Remote Control as a Wireless Compu-  
ter Mouse .................................................... 19  
Quick Start  
Quick Start .................................................... 20  
Setup  
Setting Up the Projector .............................. 22  
Setting Up the Projector .................................... 22  
Projecting a Reversed Image ............................ 23  
Connections  
Connecting to Video Equipment That Has a DVI  
Output Terminal with a DVI Digital Cable… 31  
Connecting to RGB Video Equipment with a  
5 RCA RGB Cable ....................................... 32  
Connecting to Video Equipment That Has  
Connections ................................................. 24  
INPUT/OUTPUT Terminals and Connectable  
Main Equipment .......................................... 24  
Samples of Cables for Connection............. 25  
Connecting to a Computer .......................... 27  
Connecting with the RGB Cable ....................... 27  
Connecting with a 5 BNC to 15-pin D-sub  
Cable ........................................................... 28  
Connecting with a DVI Digital Cable ................. 29  
Connecting to Video Equipment ................. 30  
Connecting to Video Equipment That Has  
Component Output Terminals ..................... 33  
Connecting with an S-video Cable or a Compos-  
ite Video Cable ............................................ 34  
Controlling the Projector by a Computer ... 35  
Connecting to a Monitor That Has an RGB  
Input Terminal ......................................... 36  
Connecting to an Amplifier or Other  
an HDMI Output Terminal with a DVI to  
HDMI Cable ................................................ 30  
Audio Equipment .................................... 36  
-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using  
Basic Operation  
Adjusting the Volume ......................................... 46  
Turning Off the Sound Temporarily .................... 46  
Displaying an Enlarged Portion of an Image ....... 46  
Freezing a Moving Image .................................. 47  
Selecting the Picture Mode ............................... 47  
Resize Mode ...................................................... 48  
Displaying the Black Screen… .......................... 50  
Displaying and Setting the Break Timer ............ 50  
Turning the Projector On/Off ....................... 37  
Image Projection .......................................... 38  
Shifting the Lens… ............................................ 38  
Using the Adjustment Feet ................................ 39  
Adjusting the Focus........................................... 40  
Adjusting the Projected Image Size .................. 40  
Correcting Trapezoidal Distortion ...................... 41  
Switching the Input Mode .................................. 45  
Useful Features  
Menu Items ................................................... 51  
Using the “Options (1)” Menu ..................... 74  
Displaying Dual Pictures (Pict in Pict) ............... 74  
Setting the Resize Mode ................................... 74  
Shifting the Projected Image Vertically  
Using the Menu Screen ............................... 56  
Menu Selections (Adjustments) ......................... 56  
Menu Selections (Settings) ................................ 58  
Picture Adjustment (“Picture” menu)......... 60  
Selecting the Picture Mode ............................... 60  
Adjusting the Image .......................................... 60  
Adjusting the Color Temperature ....................... 61  
Emphasizing the Contrast ................................. 61  
Selecting the Progressive Mode........................ 62  
Reducing Image Noise (DNR) ........................... 62  
Signal Type Setting ............................................ 63  
Color Management System  
(“C. M. S.menu) ..................................... 64  
Selecting the Color Reproduction Mode ........... 64  
Selecting the Target Color ................................. 64  
Setting the Brightness of the Target Color ......... 65  
Setting the Chromatic Value of the Target Color ... 65  
Setting the Hue of the Target Color ................... 66  
Resetting User-defined Color Settings .............. 66  
Overview of All Color Settings ........................... 67  
Computer Image Adjustment  
(“Fine Sync” menu) ................................ 68  
Adjusting the Computer Image ......................... 68  
Saving Adjustment Settings… ........................... 68  
Selecting Adjustment Settings… ....................... 69  
Special Mode Setting ........................................ 69  
Checking the Input Signal ................................. 70  
Auto Sync Adjustment ....................................... 70  
Auto Sync Display Function .............................. 71  
Audio Adjustment (“Audio” menu) ............. 72  
Adjusting the Audio ........................................... 72  
Setting the Audio Output Type .......................... 72  
Speaker Setting ................................................. 73  
(Digital Shift) ................................................ 75  
Setting On-screen Display................................. 75  
Setting the Video System................................... 76  
Capturing Projected Images ............................. 76  
Selecting the Background Image ...................... 77  
Selecting the Startup Image .............................. 77  
Eco Mode .......................................................... 78  
Detecting the Input Signals Automatically ........ 78  
Auto Power Off Function .................................... 79  
System Lock Function ....................................... 79  
Helpful Functions Set during Installation  
(“Options (2)” menu) .............................. 82  
Setting a Password ............................................ 82  
Checking the Lamp Life Status ......................... 83  
Setting the Lamp Mode ..................................... 83  
Reversing/Inverting Projected Images .............. 84  
Controlling Multiple Projectors with the One  
Remote Control ........................................... 84  
Shortcut to Make Projector Stack Settings ........ 85  
Locking the Operation Buttons on the Projector ... 85  
Bypassing Unused Input Selections ................. 86  
Selecting the Fan Mode ....................................... 86  
Direct Power On Function .................................... 87  
Selecting the Transmission Speed (RS-232C)....... 87  
Monitor Output Settings..................................... 88  
LAN/RS232C Setting ......................................... 88  
DHCP Client Setting .......................................... 89  
TCP/IP Setting ................................................... 89  
Service Mode .................................................... 90  
Returning to the Default Settings....................... 91  
Using the Other Menus (“Language” and  
“Status” menus) ..................................... 92  
Selecting the On-screen Display Language ....... 92  
Overview of All Menu Settings ........................... 92  
-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Reference  
Appendix  
Maintenance ................................................. 93  
Maintenance Indicators ............................... 94  
Specifications ............................................. 105  
Glossary...................................................... 106  
Index ............................................................ 107  
Regarding the Lamp .................................... 96  
Lamp ................................................................. 96  
Caution Concerning the Lamp .......................... 96  
Replacing the Lamp .......................................... 96  
Removing and Installing the Lamp Unit ............ 97  
Resetting the Lamp Timer ................................. 99  
Computer Compatibility Chart .................. 100  
Troubleshooting ......................................... 102  
For SHARP Assistance .............................. 104  
The optional lenses are introduced on page 12. Please purchase the lens for your desired  
usage.  
-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Access the PDF Operation Manuals  
PDF operation manuals in several languages are included in the CD-ROM, so that you can  
work with the projector.To utilize these manuals, you need to install Adobe® Reader® on your  
computer (Windows® or Macintosh®).  
Please download Adobe® Reader® from the Internet (http://www.adobe.com).  
Accessing the PDF manuals  
For Windows®:  
For Macintosh®:  
1 Insert the CD-ROM in the CD-ROM drive.  
2 Double click the “My Computer” icon.  
3 Double click the “CD-ROM” drive.  
1 Insert the CD-ROM in the CD-ROM drive.  
2 Double click the “CD-ROM” icon.  
3
When you want to view the operation manual  
1) Double click the “MANUALS” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
4
When you want to view the operation manual  
1) Double click the “MANUALS” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the “PH70_” pdf file to access  
the projector manuals.  
When you want to view the setup manual  
1) Double click the “SETUP” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the “PH70_” pdf file to access  
the projector manuals.  
When you want to view the setup manual  
1) Double click the “SETUP” folder.  
2) Double click the language (name of the  
folder) that you want to view.  
3) Double click the “S_PH7_” pdf file to access  
the setup manual.  
3) Double click the “S_PH7_” pdf file to access  
the setup manual.  
Info  
If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then  
specify the desired file using the “File”, “Open” menu.  
SETUP MANUAL  
Refer to the “SETUP MANUALcontained on the supplied CD-ROM for details.  
Setting up the Screen .................................... 2  
Screen Size and Projection Distance ........... 3  
Connecting Pin Assignments ..................... 10  
RS-232C Specifications and Commands ... 12  
Setting up the Projector Network  
Environment............................................ 17  
Controlling the Projector via LAN .............. 23  
Setting the Projector Using  
Controlling the Projector Using  
RS-232C or Telnet ................................... 31  
Stack Projection ........................................... 38  
Video Wall Projection ................................... 41  
Resetting the Lamp Timer  
of the Projector via LAN......................... 50  
Troubleshooting ........................................... 52  
Dimensions................................................... 55  
RS-232C or Telnet ................................... 28  
-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
CAUTION: Please read all of these instructions before you operate this product and save these  
instructions for later use.  
Electrical energy can perform many useful functions. This product has been engineered and manufactured to  
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR  
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic  
rules for its installation, use and servicing.  
1. Read Instructions  
13. Power-Cord Protection  
All the safety and operating instructions should be read before  
the product is operated.  
Power-supply cords should be routed so that they are not  
likely to be walked on or pinched by items placed upon or  
against them, paying particular attention to cords at plugs,  
convenience receptacles, and the point where they exit from  
the product.  
2. Retain Instructions  
The safety and operating instructions should be retained for  
future reference.  
14. Lightning  
3. Heed Warnings  
For added protection for this product during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet and disconnect the cable  
system. This will prevent damage to the product due to  
lightning and power-line surges.  
All warnings on the product and in the operating instructions  
should be adhered to.  
4. Follow Instructions  
All operating and use instructions should be followed.  
5. Cleaning  
15. Overloading  
Unplug this product from the wall outlet before cleaning. Do  
not use liquid cleaners or aerosol cleaners. Use a damp cloth  
for cleaning.  
Do not overload wall outlets, extension cords, or integral  
convenience receptacles as this can result in a risk of fire or  
electric shock.  
6. Attachments  
16. Object and Liquid Entry  
Do not use attachments not recommended by the product  
manufacturer as they may cause hazards.  
Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points or  
short-out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
7. Water and Moisture  
Do not use this product near water–for example, near a bath  
tub, wash bowl, kitchen sink, or laundry tub; in a wet  
basement; or near a swimming pool; and the like.  
17. Servicing  
Do not attempt to service this product yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
8. Accessories  
Do not place this product on an unstable cart, stand, tripod,  
bracket, or table. The product may fall, causing serious injury  
to a child or adult, and serious damage to the product. Use  
only with a cart, stand, tripod, bracket, or table recommended  
by the manufacturer, or sold with the product. Any mounting  
of the product should follow the manufacturer’s instructions,  
and should use a mounting accessory recommended by the  
manufacturer.  
18. Damage Requiring Service  
Unplug this product from the wall outlet and refer servicing  
to qualified service personnel under the following conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into  
the product.  
9. Transportation  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following  
the operating instructions. Adjust only those controls  
that are covered by the operating instructions, as an  
improper adjustment of other controls may result in  
damage and will often require extensive work by a  
qualified technician to restore the product to normal  
operation.  
A product and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the product and cart  
combination to overturn.  
10. Ventilation  
Slots and openings in the cabinet are provided for ventilation  
to ensure reliable operation of the product and to protect it  
from overheating, and these openings must not be blocked  
or covered. The openings should never be blocked by placing  
the product on a bed, sofa, rug, or other similar surface. This  
product should not be placed in a built-in installation such as  
a bookcase or rack unless proper ventilation is provided or  
the manufacturer’s instructions have been adhered to.  
e. If the product has been dropped or damaged in any  
way.  
f. When the product exhibits a distinct change in  
performance, this indicates a need for service.  
19. Replacement Parts  
When replacement parts are required, ensure that the service  
technician has used replacement parts specified by the  
manufacturer or have the same characteristics as the original  
part. Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
11. Power Sources  
This product should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supply to your home, consult your product  
dealer or local power company. For products intended to  
operate from battery power, or other sources, refer to the  
operating instructions.  
20. Safety Check  
Upon completion of any service or repairs to this product,  
ask the service technician to perform safety checks to  
determine that the product is in proper operating condition.  
12. Grounding or Polarization  
This product is provided with one of the following types of  
plugs. If the plug should fail to fit into the power outlet,  
please contact your electrician.  
21  
.
Wall or Ceiling Mounting  
This product should be mounted to a wall or ceiling only as  
recommended by the manufacturer.  
22. Heat  
Do not defeat the safety purpose of the plug.  
a. Two-wire type (mains) plug.  
This product should be situated away from heat sources such  
as radiators, heat registers, stoves, or other products  
(including amplifiers) that produce heat.  
b. Three-wire grounding type (mains) plug with a  
grounding terminal.  
This plug will only fit into a grounding type power  
outlet.  
-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ensure that you read the following safeguards when  
setting up your projector.  
Caution concerning the lamp unit  
Potential hazard of glass particles if lamp rup-  
tures. In case of lamp rupture, contact your  
nearest Sharp Authorized Projector Dealer  
or Service Center for replacement. See “Re-  
placing the Lamp” on page 96.  
The projector may be safely tilted to a  
maximum angle of 9 degrees.  
Placement should be within 9 degrees of  
horizontal.  
If you have application requiring tilt angle  
exceeding 9 degrees, please check with your  
local Sharp sales office.  
When using the projector in high-altitude  
areas such as mountains (at altitudes of  
approximately 1,500 meters (4,900 feet)  
or more)  
When you use the projector in high-altitude  
areas with thin air, set “Fan Mode” to “High”.  
Neglecting this can affect the longevity of the  
optical system.  
Caution concerning the setup of the pro-  
jector  
For minimal servicing and to maintain high  
image quality, SHARP recommends that this  
projector be installed in an area free from hu-  
midity, dust and cigarette smoke. When the  
projector is subjected to these environments,  
the vents and lens must be cleaned more  
often. As long as the projector is regularly  
cleaned, use in these environments will not  
reduce the overall operation life of the unit.  
Internal cleaning should only be performed  
by a Sharp Authorized Projector Dealer or  
Service Center.  
Warning about placing the projector in a  
high position  
When placing the projector in a high posi-  
tion, make certain it is carefully secured to  
avoid personal injury caused by the projec-  
tor falling down.  
Do not set up the projector in places ex-  
posed to direct sunlight or bright light.  
Position the screen so that it is not in direct  
sunlight or room light. Light falling directly on  
the screen washes out the colors, making  
viewing difficult. Close the curtains and dim  
the lights when setting up the screen in a  
sunny or bright room.  
Do not subject the projector to hard im-  
pact and/or vibration.  
Take care with the lens so as not to hit or  
damage the surface of the lens.  
Rest your eyes occasionally.  
Continuously watching the screen for long  
hours will cause eye strain. Take regular  
breaks to rest your eyes.  
Avoid locations with extremes of tem-  
perature.  
The operating temperature of the projector  
is from 41°F to 104°F (+5°C to +40°C).  
The storage temperature of the projector is  
from –4°F to 140°F (–20°C to +60°C).  
-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
Do not block the intake and exhaust  
vents.  
Using the projector in other countries  
The power supply voltage and the shape of  
the plug may vary depending on the region  
or country you are using the projector in.  
When using the projector overseas, make  
sure you use an appropriate power cord for  
the country you are in.  
Allow at least 11 13/16 inches (30 cm) of space  
between the exhaust vent and the nearest  
wall or obstruction.  
Ensure that the intake vents and the exhaust  
vent are not obstructed.  
If the cooling fan becomes obstructed, a pro-  
tection circuit will automatically put the pro-  
jector into standby mode to prevent overheat  
damage. This does not indicate a malfunc-  
tion (See pages 94 and 95.).Remove the pro-  
jector power cord from the wall outlet and wait  
at least 10 minutes.Place the projector where  
the intake and exhaust vents are not blocked,  
plug the power cord back in and turn on the  
projector. This will return the projector to the  
normal operating condition.  
Temperature monitor function  
If the projector starts to over-  
heat due to setup problems or  
blockage of the air vents, “  
and “ ” will illuminate in  
the lower left corner of the picture. If the tem-  
perature continues to rise, the lamp will turn off,  
the temperature warning indicator on the pro-  
jector will blink, and after a 90-second cooling-  
off period the projector will enter the standby  
mode. Refer to “Maintenance Indicators” on  
page 94 for details.  
Caution regarding usage of the projector  
When using the projector, take care not to sub-  
ject it to hard impact and/or vibration, as this  
can result in damage. Take extra care with the  
lens. If you are not to use the projector for a  
long time, make certain you unplug the power  
cord from the wall outlet, and disconnect any  
other cables connected to it.  
Do not carry the projector by holding the lens.  
When storing the projector, ensure you at-  
tach the lens cap to the projector. (See page  
13.)  
Info  
The cooling fan regulates the internal tem-  
perature, and its performance is automati-  
cally controlled.The sound of the fan may  
change during projector operation due to  
changes in the fan speed. This does not  
indicate malfunction.  
Even if you unplug the power cord after  
projector operation, the cooling fan con-  
tinues to run for a while. When you place  
the projector into the storage case, make  
sure that the cooling fan has stopped.  
Do not expose the projector to direct sunlight  
or near heat sources. The projector may  
change color or become deformed.  
Other connected equipment  
Optional lens installation  
Be sure to have service personnel install the  
optional lenses.  
When connecting a computer or other audio-  
visual equipment to the projector, make the  
connections AFTER unplugging the power  
cord of the projector from the AC outlet and  
turning off the equipment to be connected.  
Please read the operation manuals of the pro-  
jector and the equipment to be connected for  
instructions on how to make the connections.  
-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
Supplied accessories  
Remote control  
9NK5041808700  
Two R-6 batteries  
(“AA” size, UM/SUM-3, HP-7 or similar)  
Power cord*  
(1)  
(4)  
(2)  
(3)  
For U.S., Canada, etc. For Europe, except U.K.  
For U.K., Hong Kong For Australia, New  
(6' (1.8 m))  
9NK3090204900  
(6' (1.8 m))  
9NK3090152700  
and Singapore  
(6' (1.8 m))  
Zealand and Oceania  
(6' (1.8 m))  
9NK3090152900  
9NK3090152600  
*Use the power cord that corresponds to the wall outlet in your country.  
Remote mouse receiver  
(5'3" (1.6 m))  
9NK3790197000  
RGB cable  
(10' (3.0 m))  
9NK3080431000  
Cap for the standard zoom lens  
(Only supplied with XG-PH70X)  
9NK3797200400  
Projector manual and  
Operation manual  
technical reference  
CD-ROM  
(this manual)  
9NK5010057700  
9NK3534022800  
Optional accessories  
Cable  
3 RCA to 15-pin D-sub cable (10' (3.0 m))  
AN-C3CP2  
Lamp  
Lamp unit 1  
Lamp unit 2  
AN-PH7LP1  
AN-PH7LP2  
Note  
Some of the optional accessories may not be available depending on the region. Please check with your  
nearest Sharp Authorized Projector Dealer or Service Center.  
-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
Optional lenses  
Lens  
Projection distance for 100" screen size  
Fixed wide lens (× 0.8)  
AN-PH10EX  
5'4" (1.6 m)  
Wide-zoom lens (× 1.5 – 1.8)  
Standard zoom lens (× 1.8 – 2.2)  
(attached to XG-PH70X)  
Tele-zoom lens (× 2.25 – 3.00)  
Tele-zoom lens (× 3.0 – 4.5)  
Tele-zoom lens (× 4.5 –7.0)  
AN-PH20EZ  
AN-PH31EZ  
10' – 12' (3.0 m – 3.7 m)  
12' – 14'8" (3.7 m – 4.5 m)  
AN-PH40EZ  
AN-PH50EZ  
AN-PH60EZ  
15' – 20' (4.6 m – 6.1 m)  
20' – 30' (6.1 m – 9.1 m)  
30' – 46'8" (9.1 m – 14.2 m)  
No lens is attached to XG-PH70X-N.The standard zoom lens is attached to XG-PH70X.  
The optional lenses from Sharp are also available for specialized application. Please see  
your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the  
lens operation manual when using a lens.) Also, be sure to have service personnel install the  
optional lenses.  
Throw Distance  
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.  
Screen  
Fixed wide lens (AN-PH10EX)  
5'4" (1.6 m)  
Throw distance ratio 1:0.8  
Wide-zoom lens (AN-PH20EZ)  
10'–12' (3.0 m–3.7 m)  
Throw distance ratio 1:1.5–1.8  
Standard zoom lens (AN-PH31EZ : Standard equipment with XG-PH70X)  
12'–14'8" (3.7 m–4.5 m)  
Throw distance ratio 1:1.8–2.2  
Tele-zoom lens (AN-PH40EZ)  
15'–20' (4.6 m–6.1 m)  
Throw distance ratio 1:2.25–3.00  
Tele-zoom lens (AN-PH50EZ)  
20'–30' (6.1 m–9.1 m)  
Throw distance ratio 1:3.0–4.5  
Tele-zoom lens (AN-PH60EZ)  
30'–46'8" (9.1 m–14.2 m)  
Throw distance ratio 1:4.5–7.0  
5
10  
15  
20  
25  
30  
35  
40  
45  
50(ft)  
-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
Numbers in  
refer to the main pages in this operation manual where the topic is explained.  
Projector  
Top View  
Power indicator  
14  
37  
14  
14  
14  
·
·
·
94 Lamp indicator 1  
94 Lamp indicator 2  
ON button  
For turning the power on.  
Temperature warning  
94  
STANDBY button  
For putting the projector  
into standby mode.  
37  
indicator  
46 Volume buttons  
For adjusting the speaker  
sound level.  
ZOOM button 40  
For adjusting the projected  
INPUT 1, 2, 3 button  
For switching input mode  
1, 2 or 3.  
45  
image size.  
45  
INPUT 4, 5 button  
For switching input mode  
4 or 5.  
FOCUS button  
40  
39  
For adjusting the focus.  
H & V LENS SHIFT button  
For shifting the lens horizontally  
and vertically.  
70 AUTO SYNC button  
For automatically  
adjusting images when  
connected to a computer.  
Adjustment buttons  
('/"/\/|)  
56  
MENU button  
For displaying adjustment  
and setting screens.  
56  
For selecting menu items  
and other settings.  
56 UNDO button  
For undoing an operation  
or returning to the previous  
display.  
ENTER button  
For setting items selected  
or adjusted on the menu.  
56  
41  
KEYSTONE button  
For entering the Keystone  
Correction mode.  
Front View  
Carrying handle  
For carrying the  
projector.  
Lamp unit cover  
97  
Speaker  
73  
93 Intake vent  
73 Speaker  
Remote control 17  
sensor  
Adjustment foot  
(on the bottom of  
the projector)  
39  
39  
Adjustment foot  
(on the bottom of  
the projector)  
Intake vent  
93  
Attaching the lens cap  
Push the lens cap on until it clicks  
into position.  
Removing the lens cap  
Pull the lens cap directly outward.  
-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
About the Indicators on the Projector  
Power indicator  
...  
Red on Normal (Standby)  
...  
Green on Normal (Power on)  
Red blinks The intake vent cover is open.  
...  
(See page 93.)  
Lamp indicators 1, 2  
...  
Green on Normal  
...  
Green blinks The lamp is warming up.  
Red on The lamp has been shut down abnormally or  
...  
needs to be changed. (See pages 94 and 95.)  
Temperature warning indicator  
...  
Off Normal  
...  
Red blinks/on The internal temperature is abnormally  
high. (See pages 94 and 95.)  
-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Numbers in  
refer to the main pages in this operation manual where the topic is explained.  
Projector (Side View)  
Terminals Refer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on  
page 24.  
INPUT 1 terminal  
Terminal for computer RGB  
and component signals.  
INPUT 3 terminal  
Terminal for DVI digital RGB  
and digital component signals.  
27  
27  
28  
29  
36  
AUDIO input (1) terminal  
Audio input terminal for  
INPUT 1.  
OUTPUT (FOR INPUT 1, 2)  
terminal  
Output terminal for computer  
RGB and component signals.  
Shared for INPUT 1 and 2.  
INPUT 2 terminals  
BNC terminals for computer  
RGB and component  
signals.  
AUDIO input (2, 3) terminal  
Shared audio input terminal for  
INPUT 2 and 3.  
28  
36  
RS-232C terminal  
Terminal for controlling the  
projector using a computer.  
35  
34  
34  
AUDIO OUTPUT terminal  
Audio output terminal shared  
for INPUT 1–5.  
INPUT 4 terminal  
Terminal for connecting  
video equipment.  
LAN terminal  
35  
37  
AUDIO input (4, 5) terminals  
Shared audio input terminals for  
INPUT 4 and 5.  
Terminal for controlling the  
projector using a computer  
via network.  
INPUT 5 terminal 34  
Terminal for connecting  
video equipment with an  
S-video terminal.  
AC socket  
Connect the supplied Power  
cord.  
WIRED REMOTE terminal  
18  
For connecting the remote  
control to the projector when  
the signals from the remote  
control cannot reach the  
remote control sensor.  
Remote control sensor  
17  
Kensington Security  
Standard connector  
Exhaust vent  
The speed and pitch of  
93  
the cooling fan may  
change during operation  
in response to internal  
temperature changes.  
This is normal operation  
and does not indicate a  
malfunction.  
Using the Kensington Lock  
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security  
System. Refer to the information that came with the system for instructions on how to use it to secure the  
projector.  
-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
Numbers in  
refer to the main pages in this operation manual where the topic is explained.  
Remote Control  
FOCUS buttons  
For bringing the projected image  
into focus.  
40  
37  
ON button  
37  
For turning the power on.  
18 ADJ./MOUSE switch  
For switching the remote control  
modes.  
STANDBY button  
For putting the projector into  
standby mode.  
H & V LENS SHIFT button  
For shifting the lens horizontally  
and vertically.  
39  
ZOOM buttons  
For adjusting the projected  
image size.  
40  
41  
MENU button  
For displaying adjustment and  
setting screens.  
56  
KEYSTONE button  
For entering the Keystone  
Correction mode.  
19  
·
56 R-click/UNDO button  
For the right click while the  
ADJ./MOUSE switch is the  
MOUSE position.  
Mouse/adjustment button  
19·56  
('/"/\/|)  
For moving the computer  
cursor while the  
For undoing an operation or  
returning to the previous  
display while the ADJ./MOUSE  
switch is the ADJ. position.  
ADJ./MOUSE switch is the  
MOUSE position.  
For selecting menu items  
while the ADJ./MOUSE  
switch is the ADJ. position.  
ENTER button  
47 FREEZE button  
For freezing images.  
For setting items selected or  
adjusted on the menu.  
Volume buttons  
For adjusting the speaker sound level.  
46  
L-click button  
For the left click while the  
ADJ./MOUSE switch is the  
MOUSE position.  
19  
46  
46 MUTE button  
For temporarily turning off the  
sound.  
ENLARGE (enlarge/reduce)  
buttons  
For enlarging/reducing part of the  
image.  
50 BLACK SCREEN button  
For temporarily display the black  
screen.  
BREAK TIMER button  
RESIZE button  
48  
50  
70  
For setting the break time.  
For switching the screen size.  
AUTO SYNC button  
For automatically adjusting images  
when connected to a computer.  
PICTURE MODE button  
For switching the picture mode.  
47  
INPUT 1, 2, 3, 4 and 5 buttons  
For switching to the respective  
input modes.  
WIRED R/C JACK  
18  
45  
For connecting the remote control  
to the projector when the signals  
from the remote control cannot  
reach the remote control sensor.  
Note  
All the buttons on the remote control, except the mouse/adjustment button and the ADJ./MOUSE switch,  
are made of luminous material that is visible in the dark.Visibility will diminish over time. Exposure to light  
will recharge the luminous buttons.  
-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Front View  
Remote control sensor  
Usable Range  
30°  
The remote control can be used to control the  
projector within the ranges shown in the il-  
lustration.  
30°  
Remote control  
signal transmitters  
30°  
23' (7 m)  
Note  
The signal from the remote control can be re-  
flected off a screen for easy operation. How-  
ever, the effective distance of the signal may  
differ depending on the screen material.  
Remote control  
Rear View  
Remote control sensor  
30°  
When using the remote control:  
Ensure that you do not drop it or expose it to  
moisture or high temperature.  
30°  
The remote control may malfunction under a  
fluorescent lamp. In this case, move the pro-  
jector away from the fluorescent lamp.  
23' (7 m)  
30°  
Remote control  
signal transmitters  
Remote control  
Inserting the Batteries  
1
Press the tab and lift open the battery  
cover in the direction of the arrow  
.
2 Insert the batteries.  
Insert the batteries making sure the po-  
larities correctly match the and  
marks inside the battery compartment.  
3 Insert the tabs on the end of the  
battery cover into their slots and  
press the cover into position.  
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.  
Caution  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
Insert the batteries making sure the polarities correctly match the  
and  
marks inside the battery compartment.  
Batteries of different types have different properties, therefore do not mix batteries of different types.  
Do not mix new and old batteries.  
This may shorten the life of new batteries or may cause old batteries to leak.  
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.  
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them  
using a cloth.  
The batteries included with this projector may run down in a short period, depending on how they are kept.  
Be sure to replace them as soon as possible with new batteries.  
Remove the batteries from the remote control if you will not be using the remote control for a long time.  
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.  
-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Using the Remote Control with a Signal Cable  
When the signals from the remote control cannot be reached due to the positioning of the projector, use a  
ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector  
with the remote control.  
Remote control  
Side view  
To WIRED REMOTE terminal  
To WIRED R/C JACK  
ø3.5 mm minijack cable (commercially available or  
available as Sharp service part QCNWGA038WJPZ)  
Note  
The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projec-  
tor. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be discon-  
nected from the projector.  
Switching the Remote Control Mode  
The remote control has two functions. One is projector control and the other is wireless computer mouse.  
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.  
Projector control  
Wireless computer mouse  
ADJ.  
ADJ.  
MOUSE  
MOUSE  
Info  
When using the remote control as the wireless computer mouse, connect the supplied remote mouse  
receiver to the computer. (See page 19.)  
-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control as a Wireless Computer Mouse  
When connecting the supplied remote  
mouse receiver to the computer, you can use  
the remote control as the wireless computer  
mouse.  
Supplied  
accessory  
Remote mouse  
receiver  
1 Connect the supplied remote  
mouse receiver to the USB termi-  
nal on the computer.  
Computer  
Remote mouse receiver  
ADJ.  
2 Slide the ADJ./MOUSE  
switch on the remote con-  
MOUSE  
trol to the MOUSE position.  
3 Use the mouse function.  
Point the remote control at the remote  
mouse receiver.  
To USB terminal  
When moving the cursor  
Press '/"/\/|.  
When left-clicking  
ADJ./MOUSE switch  
Press  
.
When right-clicking  
Press  
Mouse/adjustment button ('/"/\/|)  
.
When your computer supports only a  
one-click mouse (such as Macintosh®)  
Press  
or  
. ( and  
have com-  
mon function.)  
R-click button  
L-click button  
Note  
This function only works with the Microsoft®  
Windows® OS and Mac OS®. However, this func-  
tion does not work with the following operation  
systems that do not support USB.  
Versions earlier than Windows® 95.  
Versions earlier than Windows® NT4.0.  
Versions earlier than Mac OS® 8.5.  
Confirm that the computer recognizes the USB  
connection.  
While the remote control is connected to the  
projector with a signal cable, you cannot use  
the wireless computer mouse function.  
-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Start  
This section shows the basic operation (projector connecting with the computer). For details, see the page  
described below for each step.  
Setup and Projection  
In this section, connection of the projector and the computer is explained using one example.  
5
4
8
3
8
5
3
4 6  
7
6
6
4
6
4 6  
7
1.Place the projector facing a screen  
Page 22  
2.Connect the projector to the computer and plug the power  
cord into the AC socket of the projector  
When connecting equipment other than the computer,  
see pages 3036.  
Pages 27–29, 37  
3.Remove the lens cap and turn the projector on  
Press  
on the projector or  
on the remote control.  
Page 37  
-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.Adjust the angle  
Adjust the projector angle by rotating the adjust-  
ment feet.  
Adjust the projector angle  
Shift the lens horizontally and vertically.  
1
2
Press  
remote control.  
Press ', ", \ or | on the projector or the  
on the projector or  
on the  
remote control.  
Pages 38, 39  
5.Adjust the focus and the zoom  
1 Press  
on the projector or  
on the remote control to adjust the focus.  
2 Press  
on the projector or  
on the remote control to adjust the zoom.  
Page 40  
6.  
Correcting the image distortion due to the projection angle  
1 Press  
on the projector or  
on the  
4 Press  
or  
to set the position.  
remote control.  
5 Repeat the same procedure with the positions  
for the upper right, lower right and lower left of  
the image.  
2 Press  
on the projector or  
on the  
remote control.  
3 Press ', ", \ or | to move the position for  
When the position of the lower left is set, the  
correction is made and the display disappears.  
the upper left of the image.  
Page 41  
7.Select the input mode  
Press  
on the projector or  
on the  
" On-screen Display (RGB)  
remote control to select the “INPUT 1” mode.  
INPUT 1 INPUT 2 INPUT 3  
When pressing  
on the projector, input mode switches in order of :  
on the projector switches between “INPUT 4” and “INPUT 5”.  
.
Pressing  
When using the remote control, press  
/
/
/
/
to switch the input mode.  
Page 45  
8.Turn the power off  
Press  
press  
on the projector or  
on the remote control. While the confirmation message is displayed,  
or  
again.  
" On-screen Display  
You can unplug the power cord even if the projector is operating.  
Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.  
Page 37  
-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector  
Setting Up the Projector  
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat  
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.  
Note  
The projector lens should be centered in the middle of the screen. If the horizontal line passing through  
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.  
For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling  
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights  
when setting up the projector in a sunny or bright room.  
Standard Setup (Front Projection)  
Place the projector at the required distance from the screen according to the desired picture size. (For  
details, refer to “SETUP MANUALcontained on the supplied CD-ROM.)  
Indication of the Projection Image Size and Projection Distance  
For details, refer to “SETUP MANUALcontained on the supplied CD-ROM.  
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-PH31EZ)  
Picture Size  
300"  
240"  
×
180"  
200"  
160"  
×
120"  
100"  
84"  
60"  
80"  
×
60"  
50"  
67"  
×
36"  
48"  
×
Projection Distance  
"
"
"–8'10  
7'2  
(2.2 m – 2.7 m)  
10'1  
"–12'4  
"
3.8 m)  
"
4.5 m)  
14'8–  
(3.1 m  
29'48.9 m)  
44'  
36'  
12'  
(3.7 m  
24'  
(7.3 m  
(11.0 m – 13.4 m)  
-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projecting a Reversed Image  
Projection from behind the Screen  
Place a translucent screen between the projector and the audience.  
Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 84.)  
Translucent screen  
Audience  
Projection Using a Mirror  
Place a mirror (normal flat type) in front of the lens.  
When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”  
menu. (See page 84.)  
When the mirror is placed on the audience side, set to “Rear” in the “PRJ Mode” menu. (See page 84.)  
Set to “Front”  
Set to “Rear”  
Mirror  
Translucent screen  
Audience  
Audience  
Mirror  
Info  
When using a mirror, ensure that both the projector and the mirror are carefully placed so the projected  
light does not shine into the eyes of the audience.  
Ceiling-mount Setup  
It is recommended that you use the optional Sharp ceiling-mount  
bracket for this installation.  
Before mounting the projector, contact your nearest Sharp Au-  
thorized Projector Dealer or Service Center to obtain the recom-  
mended ceiling-mount bracket (sold separately).  
AN-PHCM20 ceiling-mount bracket, its AN-EP101AP extension  
tube (for the U.S.A.).  
AN-NV6T ceiling-mount bracket, its AN-TK201 and AN-TK202  
extension tubes (for countries other than the U.S.A.).  
Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See  
page 84 for use of this function.  
-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
INPUT/OUTPUT Terminals and Connectable Main Equipment  
AUDIO input (1) terminal  
Connecting an audio cable.  
(Audio input terminal  
dedicated to INPUT 1.) (See  
page 27.)  
OUTPUT (FOR INPUT 1, 2)  
terminal  
Connecting the monitor when you  
INPUT 1, 2 terminal  
want to simultaneously watch the  
projection image on the monitor.  
(See page 36.)  
Connecting the computer. (See  
pages 27 and 28.)  
Connecting video equipment with  
component output terminal (DVD  
player, DTV decoder, DVD recorder  
with hard disc, etc.). (See page 33.)  
INPUT 3 terminal  
Connecting the computer. (See  
page 29.)  
Connecting video equipment with  
HDMI or DVI output terminal (DVD  
player, DTV decoder, DVD recorder  
with hard disc, etc.). (See pages 30  
and 31.)  
AUDIO input (2, 3) terminal  
Connecting an audio cable. (Shared  
audio input terminal for INPUT 2  
and 3.) (See pages 28 and 29.)  
AUDIO OUTPUT terminal  
Connecting an audio cable.  
(Shared audio output terminal for  
INPUT 1 – 5.) (See page 36.)  
LAN terminal  
(10 BASE-T/100 BASE-TX)  
Connecting the computer or the  
hub using a LAN cable. (See page  
35.)  
RS-232C terminal  
Connecting the computer to  
control the projector.  
(See page 35.)  
WIRED REMOTE terminal  
For connecting the remote control when  
the signals from the remote control cannot  
reach the remote control sensor. (See  
page 18.)  
INPUT 5 terminal  
AUDIO input (4, 5) terminals  
Connecting an audio cable.  
(Shared audio input terminals for  
INPUT 4 and 5.) (See page 34.)  
INPUT 4 terminal  
Connecting video equipment without  
S-video output terminal. (See page 34.)  
Connecting video equipment with S-video  
output terminal (VCR, DVD player, etc.).  
(See page 34.)  
-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Samples of Cables for Connection  
For more details of connection and cables, refer to the operation manual of the connecting equipment.  
You may need other cables or connectors not listed below.  
Terminal on  
Terminal on the  
projector  
Equipment  
Computer  
Cable  
connected equipment  
RGB cable (supplied)  
INPUT 1  
RGB  
output  
5 BNC to 15-pin D-sub cable (commercially available) INPUT 2  
terminal  
DVI digital DVI Digital cable (commercially available)  
INPUT 3  
video  
output  
terminal  
ø3.5 mm stereo or mono audio cable (commercially  
AUDIO (for INPUT 1)  
available or available as Sharp service part  
QCNWGA038WJPZ)  
Audio  
output  
AUDIO (for INPUT 2, 3)  
terminal  
Audio-visual  
equipment  
DVI to HDMI cable (commercially available)  
INPUT 3  
HDMI  
output  
terminal  
DVI digital DVI Digital cable (commercially available)  
video  
output  
terminal  
5 RCA RGB cable (commercially available)  
INPUT 2  
BNC to RCA adaptors (commercially available)  
RGB  
output  
terminal  
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)  
INPUT 1  
INPUT 2  
Component  
video  
BNC to RCA adaptors (commercially available)  
output  
terminal  
Component video cable (commercially available)  
-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Samples of Cables for Connection  
Terminal on  
Terminal on the  
projector  
Equipment  
Cable  
connected equipment  
Audio-visual  
equipment  
Video cable (commercially available)  
S-video cable (commercially available)  
INPUT 4  
Video  
output  
terminal  
INPUT 5  
S-video  
output  
terminal  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
AUDIO (for INPUT 1)  
AUDIO (for INPUT 2, 3)  
Audio  
output  
terminal  
RCA audio cable (commercially available)  
AUDIO (for INPUT 4, 5)  
Monitor  
RGB cable (supplied or commercially available)  
OUTPUT  
RGB  
input  
terminal  
Amplifier  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
AUDIO OUTPUT  
Audio  
input  
terminal  
-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Computer  
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,  
and that the devices to be connected are turned off. After making all connections, turn on the  
projector and then the other devices. When connecting a computer, ensure that it is the last  
device to be turned on after all the connections are made.  
Ensure the operation manuals of the devices to be connected have been read before making connections.  
Note  
See page 100 “Computer Compatibility Chart” for a list of computer signals compatible with the projector.  
Use with computer signals other than those listed may cause some of the functions to not work.  
Connecting computers other than the recommended types may result in damage to the projector, the  
computer, or both.  
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest  
Macintosh Dealer.  
Depending on the computer you are using, an image may not be projected unless the computer’s  
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a  
SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to  
enable your computer’s external output port.  
Connecting with the RGB Cable  
Supplied  
RGB cable  
accessory  
Computer  
Side view  
To INPUT 1 terminal  
RGB cable  
To AUDIO input (1) terminal  
To RGB output  
terminal  
ø3.5 mm stereo or mono audio cable  
(commercially available or available as Sharp  
service part QCNWGA038WJPZ)  
To audio output terminal  
Note  
With this connection, the projector is not compatible to the sync on green signals.  
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.  
-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Computer  
Connecting with a 5 BNC to 15-pin D-sub Cable  
The projector employs a 5 BNC computer input to prevent deterioration of image quality.  
When connecting the input terminals on the projector to the computer directly, Connect the  
R (PR), G/G sync (Y), B (PB), HD/C sync and VD cables of the 5 BNC to 15-pin D-sub cable  
(commercially available) to the INPUT 2 terminals on the projector.  
Side view  
Computer  
To AUDIO input  
(2, 3) terminal  
To INPUT 2 terminals  
To RGB output  
terminal  
5 BNC to 15-pin D-sub cable  
(commercially available)  
To audio output  
terminal  
ø3.5 mm stereo or mono audio cable  
(commercially available or available as  
Sharp service part QCNWGA038WJPZ)  
Note  
When connecting the projector to a compatible computer other than a PC (VGA/SVGA/XGA/SXGA/UXGA)  
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more  
information.  
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm  
stereo audio cable.  
The HD/C sync terminal is only for TTL signal.  
-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting with a DVI Digital Cable  
The projector employs the DVI digital input terminal for direct input of digital video signals  
from a computer.  
Computer  
Side view  
To INPUT 3 terminal  
To AUDIO input  
(2, 3) terminal  
To DVI digital  
output terminal  
DVI Digital cable  
(commercially available)  
To audio output  
terminal  
ø3.5 mm stereo or mono audio cable  
(commercially available or available as  
Sharp service part QCNWGA038WJPZ)  
Note  
When connecting the projector to a computer in this way, select “D. PC RGB” for “Signal Type” in the  
“Picture” menu.  
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm  
stereo audio cable.  
-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment  
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,  
and that the devices to be connected are turned off. After making all connections, turn on the  
projector and then the other devices.  
The projector has a DVD digital terminal, computer-RGB/component terminal, S-video terminal  
and video terminal for video input. Refer to the listed illustrations on how to connect audio-  
visual equipment.  
If your audio-visual equipment has an RGB output terminal or component output terminal,  
use the computer-RGB/component terminals (INPUT 1 or 2) on the projector for video con-  
nection.  
Connecting to Video Equipment That Has an HDMI Out-  
put Terminal with a DVI to HDMI Cable  
Use a DVI to HDMI cable when connecting HDMI video equipment such as DVD players to the  
INPUT 3 terminal.  
Side view  
Video Equipment  
To INPUT 3 terminal  
To AUDIO input  
(2, 3) terminal  
To audio output  
terminals  
DVI to HDMI cable  
(commercially available)  
To HDMI output terminal  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
Note  
Select the input signal type of the video equipment. See page 63.  
While the projector is connected to video equipment that has an HDMI output terminal, only the video  
signal can be input to the projector. (Connect the AUDIO input (2, 3) terminal for audio input.)  
Depending on specifications of video equipment or DVI to HDMI digital cable, the signal transmission  
may not work property. (The HDMI specification does not support all connections to video equipment that  
has HDMI digital output terminal using a DVI to HDMI digital cable.)  
For details on compatibility for connection, see support information on DVI connection provided by the  
video equipment manufacturer.  
-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment That Has a DVI Output  
Terminal with a DVI Digital Cable  
Use a DVI Digital cable when connecting video equipment with the DVI output terminal such  
as DVD players to the INPUT 3 terminal.  
Video Equipment  
Side view  
To INPUT 3 terminal  
To AUDIO input  
(2, 3) terminal  
To audio output  
terminals  
DVI Digital cable  
(commercially available)  
To DVI output terminal  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
Note  
Select the input signal type of the video equipment. See page 63.  
-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment  
Connecting to RGB Video Equipment with a 5 RCA RGB  
Cable  
Use a 5 RCA RGB cable when connecting the RGB video equipment such as DVD players and  
DTV* decoders to the INPUT 2 terminals.  
* DTV is the umbrella term used to describe the new digital television system in the United  
States.  
Video Equipment  
Side view  
To analog RGB  
output terminals  
To AUDIO input  
(2, 3) terminal  
To INPUT 2  
terminals  
To audio output  
terminals  
ø3.5 mm stereo minijack to  
RCA audio cable  
(commercially available)  
To BNC to RCA  
adaptors  
BNC to RCA adaptors  
commercially available  
(
)
5 RCA RGB cable  
(commercially available)  
Note  
When connecting the projector to the video equipment in this way, select “RGB” for “Signal Type” in the  
“Picture” menu. See page 63.  
The HD/C sync and VD terminals may be used depending on the specifications of the DTV decoder  
connected to this projector. Please refer to the operation manual of the DTV decoder for details.  
The HD/C sync terminal is only for TTL signal.  
-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment That Has Component  
Output Terminals  
When connecting the video equipment that has component output terminals to the INPUT 1  
terminal, use the 3 RCA to 15-pin D-sub cable (optional: AN-C3CP2).  
Video Equipment  
Side view  
To component video  
output terminals  
Y(green)  
To INPUT 1  
terminal  
PB(CB)(blue)  
R(CR)(red)  
To AUDIO input (1) terminal  
P
3 RCA to 15-pin D-sub cable  
(optional: AN-C3CP2)  
ø3.5 mm stereo minijack to  
RCA audio cable  
To audio output  
terminals  
(commercially available)  
When connecting the video equipment that has component output terminals to the INPUT 2  
terminals, use the BNC to RCA adaptors (commercially available).  
Side view  
Video Equipment  
To component video  
output terminals  
Y(green)  
P
B(CB)(blue)  
R(CR)(red)  
P
To INPUT 2 terminals  
(R(PR)/G/G sync (Y)/B (PB))  
To AUDIO input (2, 3)  
terminal  
BNC to RCA adaptors  
(commercially available)  
To audio output  
terminals  
Component video cable  
(commercially available)  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
Note  
ø3.5 mm stereo minijack to RCA audio cable (commercially available) is required for audio input.  
Select “480P/525P” or “576P/625P” for “Special Modes” on the “Fine Sync” menu, if necessary. (See page  
69.)  
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-  
mercially available cable that fits in the projector terminal you want to connect.  
The projector does not support RGBC signals via the Euro-scart.  
-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Video Equipment  
Connecting with an S-video Cable or a Composite Video Cable  
Connect the video equipment to the INPUT 4 or 5 terminal using the S-video cable or com-  
posite video cable (commercially available).  
Side view  
Video Equipment  
To INPUT 4  
terminal  
To INPUT 5  
terminal  
To AUDIO input  
(4, 5) terminals  
To S-video  
output terminal  
To video output  
terminal  
To audio output  
terminals  
Composite video cable (commercially available)  
RCA audio cable (commercially available)  
S-video cable (commercially available)  
Note  
The S-video signal input to the S-VIDEO terminal is separated into color and luminance signals for real-  
izing a higher-quality image.  
An RCA audio cable (commercially available) is required for audio input.  
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-  
mercially available cable that fits in the projector terminal you want to connect.  
-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling the Projector by a Computer  
When the RS-232C terminal on the projector to the RS-232C serial terminal on the computer,  
or when the LAN terminal on the projector to the LAN terminal on the computer, the com-  
puter can be used to control the projector. Refer to the “SETUP MANUALcontained on the  
supplied CD-ROM for details.  
When connecting to a computer using an RS-232C serial control cable  
Computer  
Side view  
To RS-232C terminal  
To RS-232C terminal  
RS-232C serial control cable  
(cross type, commercially available)  
Note  
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the  
operation manual of the computer for details.  
Refer toSETUP MANUALcontained on the supplied CD-ROM for the RS-232C specifications and  
commands.  
Info  
Do not connect the RS-232C cable to a terminal other than the RS-232C terminal on the computer. This  
may damage your computer or projector.  
Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This  
may damage your computer.  
When connecting to the LAN terminal using a LAN cable  
LINK LED (green)  
Illuminates when linked.  
Hub or computer  
TX/RX LED (yellow)  
Illuminates when  
transmitting/receiving data.  
Side view  
* To ensure safety, do not  
connect the LAN terminal  
with any cables such as a  
telephone line that may  
To LAN terminal  
cause excessive voltage.  
To LAN terminal  
LAN cable  
(Category 5 type, commercially available)  
Note  
When connecting to a hub, use straight-through Category 5 (CAT.5) type cable (commercially available).  
When connecting to a computer, use cross-over Category 5 (CAT.5) type cable (commercially available).  
-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Monitor That Has an RGB Input Terminal  
You can display computer images on a monitor using the RGB cables.  
Computer  
Side view  
Monitor  
To RGB output  
terminal  
To OUTPUT  
(FOR INPUT 1, 2) terminal  
To INPUT 1  
terminal  
RGB cable (supplied  
or commercially  
available)  
To RGB input  
terminal  
RGB cable (supplied or  
commercially available)  
Note  
RGB signals and component signals input from the INPUT 1 or INPUT 2 terminals can be output to the  
monitor.  
For inputting video signals from the INPUT 1 terminal, another RGB cable (commercially available) is  
required.  
Connecting to an Amplifier or Other Audio Equipment  
Audio signals input from equipment connected to each audio input terminal of the projector  
can be output to audio equipment.  
Amplifier  
Side view  
To audio input  
terminals  
To AUDIO OUTPUT  
(1 – 5) terminal  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
Note  
ø3.5 mm stereo minijack to RCA audio cable (commercially available) is required for audio input.  
When turning off the power in the case of connecting an amplifier or other audio equipment, first turn off  
the power of the amplifier and then turn off the power of the projector.  
By using external audio components, the volume can be amplified for better sound.  
For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 72.  
-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the Projector On/Off  
Supplied  
accessory  
Power cord  
Connecting the Power Cord  
Plug the supplied power cord into the  
AC socket on the rear of the projector.  
Then plug into the AC outlet.  
Side view  
Turning the Projector On  
To AC socket  
Before performing the steps in this section,  
connect any equipment that you use with the  
projector. (See pages 2736.)  
To AC outlet  
Power cord  
Remove the lens cap and press  
on the  
projector or on the remote control.  
Info  
The power indicator illuminates green.  
After the lamp indicator illuminates, the projec-  
tor is ready to start operation.  
When System Lock is set, the keycode input  
screen appears. Enter the right keycode to  
start projection. See page 79 for details.  
If “Direct Power On” is set to “ON”, the projector will  
be turned on automatically when you plug the power  
cord into the AC outlet. (See page 87.)  
English is the factory preset language. If you want to  
change the on-screen display to another language,  
change the language according to the procedure on  
page 92.  
Note  
ON button  
The lamp indicator illuminates or blinks, in-  
dicating the status of the lamp.  
Green: The lamp is on.  
STANDBY  
button  
Power indicator  
Lamp indicators 1, 2  
Blinking green: The lamp is warming up.  
Red: The lamp is shut down abnor-  
mally or the lamp should be  
replaced.  
When switching on the projector, a slight flicker-  
ing of the image may be experienced within the  
first minute after the lamp has been illuminated.  
This is normal operation as the lamp’s control  
circuitry is stabilizing the lamp output charac-  
teristics. This does not indicate malfunction.  
ON button  
STANDBY  
button  
If the projector is put into standby mode and  
immediately turned on again, the lamp may  
take some time to illuminate.  
Turning the Power Off (Put-  
ting the Projector into Standby Mode)  
Lens cap  
On-screen Display  
1 Press  
on the projector or  
on the remote control, then  
press that button again while the  
confirmation message is dis-  
played, to put the projector into  
standby mode.  
Info  
You can unplug the power cord even if the projector is op-  
erating.  
Even if you unplug the power cord from the projector, the  
cooling fan continues to run for a while.  
-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Shifting the Lens  
In addition to the zoom function and adjustment of projection angle using the adjust-  
ment feet, you can adjust the position of the projection using the lens shift function.  
This is a useful function in cases such as when the screen cannot be moved.  
When moving upward or downward When moving in the left and right direction  
ange  
le r  
Adjustab  
ange  
le r  
Adjustab  
Adjustable  
range  
Adjustable range  
The adjustable range is shown below.  
Horizontal range: 15%  
Vertical range: +50% (to the upper side)  
The adjustable range has limitations even within the range shown above.  
The image can be adjusted as shown on the diagram.  
AN-PH20EZ, AN-PH31EZ, AN-PH40EZ, AN-PH50EZ, AN-PH60EZ  
Height of the image × 50%  
The position of the image when  
the vertical position of the image  
is center and the horizontal  
position is the lowest  
Height of the image × 10%  
Image center  
: Areas on which the image is  
masked with a shadow while  
using the lens shift function.  
Width of the image × 15%  
AN-PH10EX  
Height of the image × 50%  
The position of the image when  
the vertical position of the image  
is center and the horizontal  
position is the lowest  
Height of the image × 18%  
Width of the image × 11%  
: Areas on which the image is  
Image center  
Width of the image × 15%  
masked with a shadow while  
using the lens shift function.  
-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Press  
on the projector or  
on the remote control.  
H & V LENS SHIFT  
button  
Pressing  
on the projector or  
on the remote control displays the test  
pattern.Checking the test pattern is use-  
ful for more accurate adjustment.  
On-screen Display  
Mouse/adjustment  
button  
('/"/\/|)  
ENTER button  
H & V LENS SHIFT  
button  
Adjustment button  
('/"/\/|)  
ENTER button  
2 Press ', ", \ or | on the pro-  
jector or the remote control to  
adjust the image position.  
Using the Adjustment Feet  
When the position of the projected image cannot be adjusted with the lens shift function, use the adjustment  
feet to adjust the projected angle.  
The height of the projector can be adjusted using the adjustment feet when the screen is located higher than  
the projector, the screen is inclined or when the installation site is slightly inclined.  
Install the projector so that it is as perpendicular to the screen as possible.  
1
While lifting the projector, rotate  
the adjustment feet.  
The projector is adjustable up to approxi-  
mately 9 degrees.  
2 Lower the projector, and then ro-  
tate the adjustment feet for the  
fine adjustment.  
When lowering the projector, be careful  
not to get your fingers caught in the area  
between the adjustment feet and the  
projector.  
Adjustment feet  
Down  
Up  
Up  
Down  
-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Adjusting the Focus  
ZOOM button  
FOCUS button  
Press  
on the projector or  
on  
the remote control to adjust the fo-  
cus.  
On-screen Display  
FOCUS buttons  
ZOOM  
buttons  
Adjusting the Projected Image Size  
Note  
Press  
on the projector or  
on  
After you have pressed the FOCUS but-  
tons or the ZOOM buttons on the remote  
control or the projector, you can display the  
test pattern by pressing the ENTER but-  
ton. The test pattern is useful for making  
more accurate adjustments.  
the remote control to adjust the pro-  
jected image size.  
On-screen Display  
For fine adjustments, when pressing the H  
& V LENS SHIFT buttons, the FOCUS but-  
tons or the ZOOM buttons, the projected  
image moves a small amount toward the  
desired direction for approximately one  
second.Hold down the buttons to move the  
projected image quickly.  
-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Correcting Trapezoidal Distortion  
When the image is projected either from the top or from the bottom towards the screen at an angle, the image  
becomes distorted trapezoidally.  
The function for correcting trapezoidal distortion is called Keystone Correction.  
There are the two types of the Keystone Correction.  
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner of the projected im-  
age  
2) “H & V KEYSTONE” for designating the correction of the horizontal and vertical axes  
Selecting the Type of the  
Correction  
KEYSTONE  
button  
Select the type of the keystone correction.  
Mouse/adjustment  
Press  
on the projector or  
on the  
button (  
'/"/\/|)  
remote control.  
“GEOMETRIC ADJUSTMENT” will be dis-  
ENTER button  
played.  
Each time  
or  
is pressed, the display  
toggles as follows:  
UNDO button  
Adjustment  
GEOMETRIC  
ADJUSTMENT  
H & V KEYSTONE  
button ('/"/\/|)  
The display  
IMAGE RESIZING *  
disappears.  
GEOMETRIC  
ADJUSTMENT  
For correcting an image desig-  
nating the corner of the pro-  
jected image  
ENTER button  
H & V KEYSTONE For correcting an image desig-  
UNDO button  
nating the horizontal or vertical  
axes  
KEYSTONE  
button  
IMAGE RESIZING For correcting the image dis-  
tortion which cannot be cor-  
rected with “H & V KEY-  
STONE”.  
*Only when “H & V KEY-  
STONE” is set to the values  
other than “0”, “IMAGE  
RESIZING” can be adjusted.  
(This function cannot be used  
when correcting with “GEO-  
METRIC ADJUSTMENT”.)  
-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
GEOMETRIC ADJUSTMENT  
On-screen Display  
1 Press  
on the projector or  
on the remote control re-  
peatedly until “GEOMETRIC  
ADJUSTMENT” is displayed.  
2 Press the buttons below to ad-  
just the position, size or focus  
of the projected image.  
Match screen’s four sides to green  
test pattern.  
Pressing ', ", \ or | on the projector  
or  
to shift the lens.  
Pressing on the projector or  
on the remote control allows you  
Geometric Adjustment  
Upper Left Upper Right Lower Right  
on  
the remote control allows you to adjust  
the projected image size.  
Pressing  
on the projector or  
on  
the remote control allows you to adjust  
the focus.  
3
4
Press  
on the remote control.  
on the projector or  
Lower Left  
Press ', ", \ or | to move the  
position for the upper left of the  
image.  
Move the upper left of the yellow frame  
onto the upper left of the screen.  
5
6
Press  
tion.  
or  
to set the posi-  
Repeat the same procedure with the  
positions for the upper right, lower  
right and lower left of the image.  
At this time, pressing  
on the pro-  
jector or on the remote control re-  
turns to the previous screen.  
Before correcting the upper left of the  
image, pressing  
or  
returns  
to the reset confirmation screen.  
When the position of the lower left is  
set, the correction is made and the  
display disappears.  
-42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H & V KEYSTONE  
on the projector or  
on the remote control re-  
On-screen Display  
1 Press  
peatedly until “H & V KEY-  
STONE” is displayed.  
When the correction has already been  
made with “GEOMETRIC ADJUST-  
MENT”, the confirmation message for  
resetting the correction before “H & V  
KEYSTONE” is displayed, and then re-  
set.  
Vertical Keystone Correction  
(Adjustment with '/ "  
2 Press ' or " to parallelize the  
left and right sides of the pro-  
jected image.  
)
3 Press \ or | to parallelize the  
upper and lower sides of the  
projected image.  
Horizontal Keystone Correction  
(Adjustment with \/ |  
)
On-screen Display  
4 Press  
or  
to display “IM-  
AGE RESIZING”.  
Only when “H & V KEYSTONE” is set  
to the values other than “0”, “IMAGE  
RESIZINGworks.  
-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
IMAGE RESIZING  
(Adjustment with '/ "/ \/ |  
5 Press ', ", \ or | to correct  
)
the image distortion.  
6 Press  
sition.  
or  
to set the po-  
-44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switching the Input  
Mode  
Select the appropriate input mode for the con-  
nected equipment.  
/
/
/
/
Press  
,
,
,
or  
on  
INPUT buttons  
the remote control to select the input  
mode.  
"On-screen Display of Input Mode (Example)  
When pressing  
input mode switches in order of :  
on the projector, the  
When pressing  
.
INPUT 1  
INPUT 2  
INPUT 3  
INPUT 1/2/3 mode  
When pressing  
on the projector, the  
Using RGB  
input mode switches between “INPUT 4” and  
“INPUT 5”.  
* The “INPUT 3”  
display is an  
example. (When  
“Signal Type” is set  
to “D. PC RGB”)  
Note  
When no signal is received, “NO SIGNAL”  
will be displayed.When non-supported sig-  
nal is received, “NOT REG.is displayed.  
When “Auto Search” of the “Options (1)”  
menu is set to “ON”, the input mode with  
signal can automatically be detected and  
displayed. (See page 78.)  
The input mode is not displayed when “OSD  
Display” of the “Options (1)” menu is set to  
“Level A” or “Level B”. (See page 75.)  
Using  
component  
* The “INPUT 3”  
display is an  
example. (When  
“Signal Type” is set  
to “D. PC Comp.”)  
About the Input mode  
When pressing  
.
INPUT 1/  
INPUT 2  
(RGB/  
Used for projecting images from  
equipment that sends RGB signals  
or component signals connected to  
INPUT 4 mode  
Using video  
component) the INPUT 1 or 2 terminals.  
INPUT 5 mode  
Using S-video  
INPUT 3 Used for projecting images  
(digital PC from equipment connected to  
RGB/digital the INPUT 3 terminal.  
PC compo-  
nent/digital  
When “Auto Search” is set to “ON”  
video RGB/  
digital video  
component)  
Pressing  
or  
once displays the  
again starts the  
current input mode.  
INPUT 4  
(video)  
Used for projecting images  
from equipment connected to  
the INPUT 4 terminal.  
Pressing  
or  
automatic input search.  
INPUT 5  
(S-video)  
Used for projecting images  
from equipment connected to  
the INPUT 5 terminal.  
-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Adjusting the Volume  
Press\/|on the projector or on the  
remote control to adjust the volume.  
Note  
Volume  
buttons  
Pressing  
or \ will lower the volume.  
or | will raise the volume.  
Pressing  
"On-screen Display  
Turning Off the Sound  
Temporarily  
Press  
on the remote control to  
temporarily turn off the sound.  
MUTE button  
Note  
Pressing  
again will turn the sound  
back on.  
"On-screen Display  
Displaying an Enlarged  
Portion of an Image  
Mouse/adjustment  
button ('/"/\/|)  
Graphs, tables and other portions of projected  
images can be enlarged. This is helpful when  
providing more detailed explanations.  
/
ENLARGE  
(enlarge/reduce)  
buttons  
1 Press  
on the remote control.  
UNDO  
button  
Enlarges the image.  
Pressing or enlarges or reduces  
the projected image.  
RESIZE  
button  
Note  
×1 ×2 ×3 ×4 ×9 ×16 ×36 ×64  
You can change the location of the en-  
larged image using ', ", \and |.  
-46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 Press  
on the remote control  
to cancel the operation.  
The magnification then returns to ×1.  
Note  
In the following cases, the image will  
return to the normal size (×1).  
When switching the input mode.  
When  
has been pressed.  
When the input signal is changed.  
When the input signal resolution and re-  
fresh rate (vertical frequency) change.  
When  
has been pressed.  
Freezing a Moving  
Image  
1 Press  
on the remote control.  
The projected image is frozen.  
FREEZE button  
2 Press  
again to return to the  
moving image from the currently  
connected equipment.  
Selecting the Picture  
Mode  
You can select the suitable picture mode for the  
projected image, such as movie or video game.  
UNDO button  
Press  
on the remote control.  
When pressing  
, the picture mode  
changes in order of  
STANDARD  
PRESENTATION  
CINEMA  
CUSTOM  
PICTURE MODE  
button  
Note  
Press  
to return to the “STANDARD”  
mode.  
This function can also be accessed from the  
OSD menu (see page 60).  
-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
This function allows you to modify or customize the resize mode to enhance the input image. Depend-  
ing on the input signal, you can choose a desired image.  
Mouse/adjustment button  
('/"/\/|)  
Resize Mode  
Press  
on the remote control.  
Pressing  
changes the display as shown.  
To return to the standard image, press  
RESIZE” is displayed on the screen.  
while  
UNDO button  
This function can also be accessed from the OSD  
menu (see page 74).  
RESIZE button  
COMPUTER  
NORMAL  
FULL  
DOT BY DOT  
BORDER  
STRETCH  
800 × 600  
1024 × 768  
1280 × 960  
1400 × 1050  
1280 × 1024  
1280 × 720  
1360 × 768  
1366 × 768  
1280 × 768  
1280 × 800  
SVGA (800 × 600)  
768 × 576  
XGA (1024 × 768)  
4:3 aspect ratio  
1024 × 768  
1024 × 576  
SXGA (1280 × 960)  
SXGA+ (1400 × 1050)  
SXGA (1280 × 1024)  
1280 × 720  
968 × 768  
1024 × 576  
1024 × 578  
1024 × 576  
1024 × 614  
1024 × 640  
720× 576  
1024 × 768  
1360 × 768  
Other aspect ratios  
1366 × 768  
1280 × 768  
960 × 576  
1024 × 576  
1280 × 800  
922 × 576  
For 4:3 screen  
FULL  
For 16:9 screen  
BORDER STRETCH  
Input signal  
Computer  
Image type  
NORMAL  
DOT BY DOT  
Resolution  
lower than  
XGA  
*
*
XGA  
SXGA (1280 × 960)  
*
4:3 aspect ratio  
Resolution  
higher than  
SXGA  
SXGA (1280 × 1024)  
5:4 aspect ratio  
16:9 aspect ratio  
*
1280 × 720  
Select “Normal”  
1360 × 768  
1366 × 768  
1280 × 768  
*
*
1280 × 800  
16:10 aspect ratio  
: Cutout area on which images cannot be projected  
: Area where the signals are off screen  
*The Digital Shift function can be used for these images.  
-48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO  
Input signal  
For 4:3 screen  
For 16:9 screen  
STRETCH  
DTV/video  
Image type  
NORMAL  
FULL  
BORDER  
SMART STRETCH  
*
*
*
*
*
*
*
*
*
*
*
4:3 aspect ratio  
*
*
480I, 480P,  
576I, 576P,  
NTSC, PAL, SECAM  
Letter box  
Squeeze  
Select “Stretch”  
Select “Full”  
16:9 aspect ratio  
540P  
4:3 aspect ratio  
in 16:9  
*
*
Select “Stretch”  
Select “Full”  
16:9 aspect ratio  
720P, 1035I, 1080I  
4:3 aspect ratio  
: Cutout area on which images cannot be projected  
: Area on which the image is not included in the original signals  
*The Digital Shift function can be used for these images.  
-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Displaying the Black  
Screen  
This function allows you to tempo-  
rarily display the black screen.  
BLACK SCREEN  
button  
1 Press  
.
Projected Image  
2 Pressing  
again will turn  
the projected image back on.  
Displaying and Setting  
the Break Timer  
BREAK TIMER  
button  
Mouse/  
This function allows you to show the re-  
maining time for break during meeting.  
adjustment  
button  
('/"/\/|)  
1 Press  
.
2 While “  
” is displayed, press  
', ", \ or | to set the break  
UNDO  
button  
timer.  
You can set anywhere between 1 and  
60 minutes (in 1 units).  
On-screen Display  
The break timer starts to count down as  
soon as ', ", \ or | is pressed.  
Note  
Pressing  
will cancel the break timer.  
Auto Power Off function will be temporarily  
disabled during the break timer.  
When no input signal is detected for more  
than 15 minutes, the projector will automati-  
cally enter the standby mode if the break  
timer has elapsed.  
The break timer will be displayed on the  
startup image. To change the screen dis-  
played during the break timer, change the  
setting of “Startup Image” (see page 77).  
When “Slave” is set for “Stack Setting”, the  
break timer is not displayed. (See page 84.)  
-50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
The following shows the items that can be set in the projector.  
“Picture” menu  
Main Menu  
Sub Menu  
INPUT 1 / INPUT 2 / INPUT 3  
Picture  
Standard  
Presentation  
Cinema  
Picture Mode  
Page 60  
Page 60  
Custom  
Contrast  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
+30  
+30  
+30  
+30  
+30  
+30  
+30  
+30  
Bright  
Color  
Tint  
*1  
*1  
*1  
*1  
Red  
Green  
Blue  
*1  
*2  
Sharp  
Page 60  
*1  
*1  
*3  
4500K  
CLR Temp  
Page 61  
10500K  
0
+10  
Bright Boost  
Pressing  
part of the “Picture” menu.  
displays the items on the lower  
Page 61  
Progressive  
2D Progressive  
3D Progressive  
Film Mode  
Page 62  
Standard  
Custom 1  
Custom 2  
Custom 3  
sRGB  
C.M.S. Adjustment  
Page 64  
*1 *4  
*5  
OFF  
DNR  
Level 1  
Level 2  
Level 3  
Page 62  
Reset  
Page 60  
INPUT 1/INPUT 2  
INPUT 3  
D.PC RGB  
Signal Type  
Auto  
RGB  
Component  
D.PC Comp.  
D.Video RGB  
D.Video Comp.  
Page 63  
*1 “Color”, “Tint”, “Red”, “Green”, “Blue”, “CLR Temp” and “Bright Boost” cannot be adjusted when “C. M. S. Adjust-  
ment” is set to “sRGB”.  
*2 “Sharp” can be adjusted only when 480  
*3 “Progressive” can be adjusted only when 480  
*4 “sRGB” can be selected under the conditions below.  
When “Signal Type” is set to “RGB”, “D. PC. RGB” or “D. Video RGB”.  
When “Signal Type” is set to “Auto” and the input signal is distinguished as “RGB”.  
*5 “DNR” can be adjusted only when 480 , 480P, 576 or 576P signal is input.  
I
, 480P, 540P, 576  
I, 576P, 720P, 1035I, or 1080I signal is input.  
I
or 576 signal is input.  
I
I
I
-51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
“Picture” menu  
INPUT 4 / INPUT 5  
Main Menu  
Sub Menu  
Picture  
Standard  
Presentation  
Cinema  
Picture Mode  
Page 60  
Page 60  
Custom  
Contrast  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
+30  
+30  
+30  
+30  
+30  
+30  
+30  
+30  
Bright  
Color  
Tint  
Red  
Green  
Blue  
Sharp  
Page 60  
4500K  
CLR Temp  
Pressing  
displays the items on the lower  
Page 61  
10500K  
part of the “Picture” menu.  
0
+10  
Bright Boost  
Page 61  
Progressive  
2D Progressive  
3D Progressive  
Film Mode  
Page 62  
Standard  
Custom 1  
Custom 2  
Custom 3  
C.M.S. Adjustment  
Page 64  
OFF  
DNR  
Level 1  
Level 2  
Level 3  
Page 62  
Reset  
Page 60  
-52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“C.M.S.menu  
Main Menu  
Sub Menu  
C.M.S.  
Standard  
Custom 1  
Custom 2  
Custom 3  
sRGB  
C.M.S. Adjustment  
Page 64  
Page 64  
[R] Red  
Target  
[Y] Yellow  
[G] Green  
[C] Cyan  
[B] Blue  
Page 64  
[M] Magenta  
Lightness  
-30  
-30  
-30  
+30  
+30  
+30  
Page 65  
Chroma  
Page 65  
Hue  
Page 66  
Reset (This Color)  
Page 66  
Reset (All Colors)  
Page 66  
View Settings  
Page 67  
“Fine Sync” menu  
Sub Menu  
Main Menu  
*6  
*7  
Fine Sync  
Clock  
Phase  
H-Pos  
V-Pos  
Reset  
-150 +150  
-30 +30  
-150 +150  
-60 +60  
Page 68  
Page 68  
Save Setting  
Page 68  
Select Setting  
Page 69  
Special Modes  
Page 69  
Signal Info  
Page 70  
Auto Sync  
OFF  
Normal  
High Speed  
Page 70  
Auto Sync Disp  
Page 71  
*6 The “Fine Sync” menu is displayed only while the input mode is INPUT 1, INPUT 2 or INPUT 3.  
*7 “Clock”, “Phase”, “H-Pos”, “V-Pos”, “Reset”, “Save Setting”, “Select Setting” and “Special Modes” can be ad-  
justed only while the input mode is INPUT 1 or INPUT 2.  
-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
“Audio” menu  
Sub Menu  
Main Menu  
Audio  
Balance  
-30  
-30  
-30  
-30  
+30  
+30  
+30  
+30  
Page 72  
Treble  
Bass  
Reset  
Page 72  
Audio Out  
FAO  
VAO  
Page 72  
Speaker [ON/OFF]  
Page 73  
“Options (1)” menu  
Main Menu  
Sub Menu  
INPUT 1 / INPUT 2 / INPUT 3  
*8  
Options (1)  
Pict in Pict  
Page 74  
Resize  
Page 74  
*9  
Normal  
Full  
Dot By Dot  
Border  
Page 74  
Stretch  
Smart Stretch  
Digi. Shift  
-96  
+96  
Page 75  
Normal  
Level A  
Level B  
OSD Display  
Page 75  
*10  
Video System  
Auto  
PAL (50/60Hz)  
SECAM  
Page 76  
NTSC4.43  
NTSC3.58  
PAL-M  
INPUT 4 / INPUT 5  
PAL-N  
*8  
Image Capture  
Save Image  
Delete  
Page 76  
Background  
Logo  
Custom  
Blue  
Page 77  
None  
Logo  
Startup Image  
Custom  
None  
Page 77  
Eco Mode [ON/OFF]  
Page 78  
Auto Search [ON/OFF]  
Page 78  
Auto Power Off [ON/OFF]  
Page 79  
System Lock  
Page 79  
*8 Item when inputting RGB signal through INPUT 1, INPUT 2 or INPUT 3  
*9 Selectable items in “Resize” mode may differ depending on the signal.  
*10 Item when selecting INPUT 4 or INPUT 5  
-54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“Options (2)” menu  
Main Menu  
Options (2)  
Sub Menu  
Old Password  
New Password  
Reconfirm  
Password  
Page 82  
Page 82  
Lamp 1  
Lamp 2  
Lamp Timer (Life)  
Page 83  
Both Lamps  
Lamp 1 Only  
Lamp 2 Only  
Equal Use  
Lamp Mode  
Page 83  
Front  
PRJ Mode  
Ceiling + Front  
Rear  
Page 84  
Ceiling + Rear  
Normal  
Master  
Slave  
Stack Setting  
Page 84  
Pair Stack  
Page 85  
Normal  
Level A  
Level B  
Keylock Level  
Page 85  
INPUT 1 [ON/OFF]  
INPUT 2 [ON/OFF]  
INPUT 3 [ON/OFF]  
INPUT 4 [ON/OFF]  
INPUT 5 [ON/OFF]  
Set Inputs  
Page 86  
Normal  
High  
Fan Mode  
Page 86  
Direct Power On [ON/OFF]  
Page 87  
9600 bps  
RS-232C  
38400 bps  
115200 bps  
Page 87  
Enable  
Disable  
Monitor Out  
Page 88  
LAN/RS232C  
Enable  
Disable  
Page 88  
Network  
DHCP Client [ON/OFF]  
TCP/IP  
*11  
Page 89  
IP Address  
Subnet Mask  
Gateway  
“Language” menu  
Service Mode  
*11 Adjustable only when DHCP  
Client is set to “OFF”  
Page 90  
All Reset  
Page 91  
Main Menu  
Sub Menu  
Language  
English  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Page 92  
Svenska  
Português  
“Status” menu  
Main menu  
Status  
Page 92  
-55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen  
The menu can be operated to achieve two functions, adjustments and settings. (For setting  
the menu items, see pages 58 and 59. )  
Mouse/  
adjustment  
button ('/"/\/|)  
ENTER button  
MENU button  
MENU button  
ENTER  
button  
UNDO button  
Adjustment  
buttons ('/"/\/|)  
UNDO button  
Menu Selections (Adjustments)  
Example: Adjusting “Bright”  
This operation can also be performed by using the buttons on the projector.  
Example: “Picture” screen menu for  
INPUT 1 (RGB) mode  
1 Press  
.
The “Picture” menu screen for the se-  
lected input mode is displayed.  
2 Press \ or | to display the other  
menu items.  
Menu items  
There are eight menu items as shown  
below.  
Menu item  
Note  
The “Fine Sync” menu is not available  
for selecting INPUT 4 or INPUT 5.  
-56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Press ' or " to select the item  
you want to adjust.  
Pressing  
displays the items on the  
lower part of the “Picture” menu.  
To adjust the pro-  
jected image while  
viewing it  
Single  
adjustment  
item  
Press  
.
The selected single adjustment item  
(e.g. “Bright”) appears instead of the  
menu.  
When pressing ' or ", the following  
item (“Color” after “Bright”) will be dis-  
played.  
Note  
Press  
to return to the previous  
screen.  
4 Press \ or | to adjust the item  
selected.  
The adjustment is stored.  
5 Press  
.
The menu screen will disappear.  
-57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen  
The menu can be operated to achieve two functions, adjustments and settings. (For adjust-  
ing the menu items, see pages 56 and 57.)  
Mouse/  
adjustment  
button ('/"/\/|)  
MENU button  
ENTER  
button  
UNDO button  
Menu Selections (Settings)  
Example: Setting “OSD Display”  
This operation can also be performed by using  
the buttons on the projector.  
1 Press  
.
Example: “Picture” screen menu for  
INPUT 1 (RGB) mode  
The “Picture” menu screen for the se-  
lected input mode is displayed.  
2 Press \ or | to display the other  
menu items.  
Menu items  
There are eight menu items as shown  
below.  
Example: “Options (1)” screen menu  
Menu item  
Note  
The “Fine Sync” menu is not available  
for selecting INPUT 4 or INPUT 5.  
-58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Press ' or " to select the  
item you want to set.  
Note  
Press  
to return to the previous  
screen.  
In some menu, select the icon using  
.
Sub menu  
4 Press | to shift the cursor to the  
sub menu.  
5 Press ' or " to select the set-  
ting of the item displayed in the  
sub menu.  
6 Press  
.
The selected item is set.  
Note  
Some adjustment items will display a  
confirmation message. When setting  
an item, press \ or | to select “Yes”  
or “OK”, press  
.
7 Press  
.
The menu screen will disappear.  
-59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” menu)  
You can adjust the projector’s picture to your preferences using the “Picture” menu.  
Selecting the Picture Mode  
Adjusting the Image  
This function allows you to select the picture  
mode in accordance with brightness of the room  
or content of the image to be projected.  
In all picture modes, items on thePicturemenu  
can be adjusted and saved.  
Select a picture mode before adjusting the im-  
age.  
Menu operation  
Page 56  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Menu operation  
Page 58  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Description of Adjustment Items  
Selectable items  
Contrast For less contrast  
Bright  
Color*1  
Tint*1  
Press  
Press  
\
|
For more contrast  
For more brightness  
For more color intensity  
For making skin tones  
greenish  
Description of Picture Modes  
For less brightness  
For less color intensity  
For making skin tones  
purplish  
Selectable items  
Standard  
Description  
For standard image  
Presentation  
Brightens darker portions of image for  
more enhanced presentations.  
Gives greater depth to darker portions  
of image for a more exciting theater  
experience.  
Red*1  
For weaker red  
For stronger red  
Green*1  
Blue*1  
For weaker green  
For weaker blue  
For less sharpness  
For stronger green  
For stronger blue  
For more sharpness  
Cinema  
Custom  
Sharp*2  
The factory preset value is the same as  
the one of “Standard”.  
*1 “Color”, “Tint”, “Red”, “Green” and “Blue” cannot  
be adjusted when “C.M.S. Adjustment” on the  
“C.M.S.menu is set to “sRGB”. (See page 64.)  
*2 “Sharp” can be adjusted only when 480I, 480P,  
540P, 576I, 576P, 720P, 1035I or 1080I DTV sig-  
nal is input during the INPUT 1, 2 or 3 mode; or  
the input mode is set to INPUT 4 or 5.  
Using the dedicated software allows  
you to adjust the gamma curve.  
Visit “http://sharp-world.com/projector/”  
for details.  
Note  
You can also press  
to select the picture mode. (See page 47.)  
on the remote control  
Note  
To reset all adjustment items, select “Reset” and  
press  
.
-60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Color Temperature  
Emphasizing the Contrast  
Menu operation  
Page 56  
This function emphasizes the bright portions of  
images to obtain a higher contrast image.  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Menu operation  
Page 56  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Description of Color Temperature Settings  
Selectable items  
Description  
4500K For lower color temperature for warmer,  
reddish incandescent-like images.  
Description of Bright Boost Setting  
Press \  
Press |  
To improve color reproduc- To increase brightness,  
For higher color temperature for cooler,  
10500K bluish, fluorescent-like images.  
tion, lower bright boost  
setting.  
increase bright boost  
setting.  
Note  
Note  
“CLR Temp” cannot be set when “C.M.S. Ad-  
justment” on the “C.M.S.” menu is set to “sRGB”.  
(See page 64.)  
“Bright Boost” cannot be set when “C.M.S. Ad-  
justment” on the “C.M.S.” menu is set to “sRGB”.  
(See page 64.)  
-61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” menu)  
Selecting the Progressive Mode  
Reducing Image Noise (DNR)  
Video digital noise reduction (DNR) provides high  
quality images with minimal dot crawl and cross  
color noise.  
Menu operation  
Page 58  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Menu operation  
Page 58  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Description of Progressive  
Selectable items  
2D  
Progressive  
3D  
Description  
Useful to display fast-moving images such  
as sports and action films.  
Useful to display relatively slowmoving  
images such as drama and documentary  
more clearly.  
Description of DNR  
Progressive  
Selectable items  
OFF  
Level 1–3  
Description  
DNR does not function.  
Sets the DNR level.  
Film Mode  
Reproduces the image of film source*  
clearly. Displays the optimized image of film  
transformed with three-two pull down (NTSC  
and PAL60Hz) or two-two pull down  
(PAL50Hz and SECAM) enhancement to  
progressive mode images.  
Note  
Set a level so as to view a clearer picture.  
Make sure to set “DNR” to “OFF” in the  
following cases:  
When the image is blurry.  
When the contours and colors of moving im-  
ages drag.  
*
The film source is a digital video recording with the original  
encoded as is at 24 frames/second. The projector can con-  
vert this film source to progressive video at 60 frames/sec-  
ond with NTSC and PAL60Hz or at 50 frames/second with  
PAL50Hz and SECAM to play back a high-definition image.  
WhenTV broadcasts with weak signals are pro-  
jected.  
Note  
In NTSC or PAL60Hz, even if the 3D Progressive  
mode has been set, the three-two pull down enhance-  
ment will be enabled automatically when the film  
source has been entered.  
When the image is blurred or noisy, switch to the  
optimal mode.  
When using progressive inputs, inputs are directly  
displayed so that “2D Progressive”, “3D Progressive”  
and “Film Mode” cannot be selected.  
Info  
This function is available for all signals with IN-  
PUT 4 and 5.  
This function is available for 480I, 480P, 576I  
and 576P signals with INPUT 1, 2 and 3.  
-62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Signal Type Setting  
This function allows you to select the input sig-  
nal type RGB or component for INPUT 1, INPUT  
2 or INPUT 3.  
Menu operation  
Page 58  
Example: “Picture” screen menu for IN-  
PUT 1 (RGB) mode  
Description of Signal Type Settings  
INPUT 1/INPUT 2  
Selectable items  
Auto  
Description  
Input signals are automatically recog-  
nized as RGB or component.  
Set when RGB signals are received.  
Set when component signals are  
received.  
RGB  
Component  
INPUT 3  
Selectable items  
D. PC RGB  
Description  
Set when digital PC RGB signals are  
received from a computer.  
D. PC Comp.  
Set when digital PC component signals  
are received from a computer.  
D. Video RGB Set when digital video RGB signals are  
received from video equipment.  
D. Video Comp. Set when digital video component  
signals are received from video equip-  
ment.  
-63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Management System (“C. M. S.” menu)  
This function allows you to individually adjust the display characteristics of six colors (R:  
Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta).  
Selecting the Color Repro-  
duction Mode  
Selecting the Target Color  
This function allows you to select the target color  
for adjusting the display characteristics.  
This function allows you to select the color re-  
production mode for the projected images.  
Menu operation  
Page 56  
Menu operation  
Page 58  
Example: “C.M.S.” screen menu  
Example: “C.M.S.” screen menu  
Description of Target Colors  
Description of C.M.S. Adjustment  
Red  
Cyan  
Blue  
Selectable items  
Standard  
Description  
Standard settings  
Yellow  
Green  
Magenta  
Custom 1 – 3  
“Lightness”, “Chroma” and “Hue” can be  
adjusted for each of the six colors.  
A natural tint based on an original im-  
age from the computer.  
sRGB  
Note  
sRGB is an international standard of color repro-  
duction regulated by the IEC (International  
Electrotechnical Commission). As the fixed color  
area has been decided by the IEC, the images  
are displayed in a natural tint based on an original  
image, whenC.M.S.Adjustmentis set tosRGB”.  
You cannot set “Color”, “Tint”, “Red”, “Green”,  
“Blue”, “CLR Temp”, “Bright Boost” on the “Pic-  
ture” menu, when “C.M.S. Adjustment” is set to  
“sRGB”.  
For additional information about the sRGB func-  
tion, visit “http://www.srgb.com/”.  
Info  
When “C.M.S. Adjustment” is set to “sRGB”, the  
projected image may become dark, but this  
does not indicate a malfunction.  
-64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Brightness of the  
Target Color  
Setting the Chromatic Value  
of the Target Color  
This function allows you to set the brightness of  
the selected target color.  
This function allows you to set the chromatic  
value of the selected target color.  
Menu operation  
Page 56  
Menu operation  
Page 56  
Example: “C.M.S.” screen menu  
Example: “C.M.S.” screen menu  
Description of Brightness  
Description of Chromatic Value  
Press \  
For less brightness of the For more brightness of the  
target color target color  
Press |  
Press \  
For less chromatic value of For more chromatic value of  
the target color the target color  
Press |  
-65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Management System (“C. M. S.menu)  
Setting the Hue of the Target  
Color  
Resetting User-defined  
Color Settings  
This function allows you to set the hue of the  
selected target color.  
This function allows you to reset the specific tar-  
get color or all of the six colors.  
Menu operation  
Page 56  
Menu operation  
Page 56  
Example: “C.M.S.” screen menu  
Example: “C.M.S.” screen menu  
Description of Hue  
Description of Reset  
Press \  
For stronger red of the  
target color  
Press |  
For stronger yellow of the  
target color  
Selectable items  
Description  
Reset (This Color) “Lightness”, “Chroma” and “Hue” of  
the color selected for “Target” are  
reset.  
Reset (All Colors) “Lightness”, “Chroma” and “Hue” of  
all colors are reset.  
-66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Overview of All Color Set-  
tings  
This function allows you to confirm the settings  
of all the colors.  
Menu operation  
Page 56  
Example: “C.M.S.” screen menu  
-67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Image Adjustment (“Fine Sync” menu)  
You can adjust the computer image, match the computer display mode, and confirm the  
input signal using the “Fine Sync” menu.  
Adjusting the Computer  
Image  
Saving Adjustment Settings  
This projector allows you to store up to seven  
adjustment settings for use with various com-  
puters.  
Use the Fine Sync function in case of irregulari-  
ties such as vertical stripes or flickering in por-  
tions of the screen.  
Menu operation  
Page 58  
Menu operation  
Page 56  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Description of Adjustment Items  
Selectable items  
Clock  
Description  
Adjusts vertical noise.  
Phase  
Adjusts horizontal noise (similar to  
tracking on your VCR).  
H-Pos  
V-Pos  
Centers the on-screen image by  
moving it to the left or right.  
Centers the on-screen image by  
moving it up or down.  
Note  
You can automatically adjust the computer im-  
age by setting “Auto Sync” on the “Fine Sync”  
menu to “Normal” or “High Speed”, or pressing  
on the projector or  
on the remote  
control. See page 70 for details.  
To reset all adjustment items, select “Reset” and  
press  
.
-68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting Adjustment Set-  
tings  
Special Mode Setting  
Ordinarily, the type of input signal is detected and  
the correct resolution mode is automatically se-  
lected. However, for some signals, the optimal  
resolution mode inSpecial Modeson theFine  
Sync” menu may need to be selected to match  
the computer display mode.  
Adjustment settings stored in the projector can  
be easily accessed.  
Menu operation  
Page 58  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Menu operation  
Page 58  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Note  
If a memory has not been set, a resolution and  
frequency setting will not be displayed.  
When selecting a stored adjustment setting with  
“Select Setting”, you can set the projector in the  
stored adjustments.  
Note  
If your computer displays patterns which repeat  
every other line (horizontal stripes), flickering  
may occur which makes the image hard to see.  
See “Checking the Input Signal” on page 70 for  
information on the currently selected input sig-  
nal.  
-69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Image Adjustment (“Fine Sync” menu)  
Checking the Input Signal  
Auto Sync Adjustment  
Menu operation  
Page 56  
Used to automatically adjust a computer image.  
Menu operation Page 58  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Note  
Description of Auto Sync Adjustment  
The projector will display the number of scanned  
lines available from audio-visual equipment  
such as a DVD player or Digital Video.  
The projector will display the resolution when  
connecting the computer.  
Selectable items  
Description  
Auto Sync adjustment is not automati-  
cally performed.  
OFF  
Auto Sync adjustment will occur when  
the projector is turned on or when the  
input signals are switched, when  
connected to a computer.  
Normal  
“Normal” takes more time than “High  
Speed” for more accurate Auto Sync  
adjustment.  
High Speed  
Note  
Auto Sync adjustment is also performed by  
pressing  
on the projector or  
on the  
remote control.  
The Auto Sync adjustment may take some time  
to complete, depending on the image of the  
computer connected to the projector.  
When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual adjust-  
ments. (See page 68.)  
When  
is pressed while “Auto Sync” is “OFF”  
or “High Speed”, Auto Sync will be executed in  
“High Speed” mode. If the button is pressed  
again within one minute, Auto Sync will be ex-  
ecuted in “Normal” mode.  
-70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auto Sync Display Function  
Used to set the display during Auto Sync.  
Menu operation  
Page 56  
Example: “Fine Sync” screen menu for  
INPUT 1 (RGB) mode  
Description of Auto Sync Display  
Selectable items  
Description  
The image set as a background image  
is projected. See page 77.  
The computer image being adjusted is  
displayed.  
-71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Adjustment (“Audio” menu)  
You can adjust the projector’s audio to your preferences using the “Audio” menu.  
Adjusting the Audio  
Setting the Audio Output Type  
This function allows you to adjust the projector’s  
audio.  
This function determines whether the audio level  
output from the AUDIO OUTPUT terminal is fixed  
or variable by linking with VOLUME.  
Menu operation  
Page 56  
Menu operation  
Page 58  
Example: “Audio” screen menu  
Example: “Audio” screen menu  
Description of Adjustment Items  
Description of Audio Out Settings  
Selectable items  
Press \  
Press |  
Selectable items  
FAO  
Description  
Audio output that does not vary in  
Balance Increased audio from Increased audio from  
the left speaker  
Treble For weaker treble  
the right speaker  
For stronger treble  
For stronger bass  
(Fixed Audio strength with the volume level of the  
Output)  
VAO  
source projector.  
Audio output that varies in strength with  
the volume level of the source projec-  
Bass  
For weaker bass  
(Variable  
Audio Output) tor.  
Note  
To reset all adjustment items, select “Reset” and  
press  
Info  
.
When “Audio Out” has been set to “VAO”, first make  
sure to lower the volume of the projector before turn-  
ing the power on or off and when switching the input.  
Note  
When the projector is connected to audio equip-  
ment:  
It is recommended that “FAO” be selected on “Audio  
Out”. Because the audio signal from the audio equip-  
ment does not vary in strength with the volume level  
of the projector, you can enjoy better sound.  
When “FAO” be selected on “Audio Out”, video and  
audio may not synchronize.  
- When connecting audio equipment that has a func-  
tion for adjusting audio delay time, adjust the de-  
lay time for synchronizing video and audio.  
- When the audio equipment does not have such a  
function and the unsynchronized video and audio  
bothers you, select “VAO” on “Audio Out”. Select-  
ing “VAO” synchronizes video and audio automati-  
cally.  
-72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Setting  
This function allows you to turn the audio out-  
put of the internal speaker on or off when the  
projector is connected to an external amplifier.  
Menu operation  
Page 56  
Example: “Audio” screen menu  
Description of Speaker Settings  
Selectable items  
Description  
The audio signal is output from the internal  
speaker.  
ON  
The audio signal is not output from the  
internal speaker.  
OFF  
-73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the “Options (1)” Menu  
You can use the “Options (1)” menu to enhance the usage for the projector.  
Displaying Dual Pictures  
(Pict in Pict)  
Setting the Resize Mode  
Depending on the input signal, you can select  
the screen image.  
The Pict in Pict (picture in picture) function allows you to  
display two pictures on the same screen.You can display  
the image input from INPUT 4 or 5 as an inset picture over-  
lapping the main picture input from INPUT 1, 2 or 3.  
Menu operation  
Page 58  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Menu operation  
Page 56  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Selectable Items of Resize Mode  
When inputting DTV/video  
When inputting RGB signal  
signal  
Note  
Normal  
Full  
Normal  
Full  
You can press  
on the remote control to select the inset  
picture image.  
You can press ' / " / \ / | on the projector or  
on the remote control to change the location of  
the inset picture image.  
(The inset picture frame will be displayed. To dis-  
play the inset picture to the desired position, move  
on the projector or  
,
Dot By Dot  
Border  
Stretch  
Border  
Stretch  
Smart Stretch  
Note  
the frame and press  
on the remote control.)  
Inset picture can only be displayed in composite  
video or S-video signal of NTSC/PAL/SECAM.  
The audio of the inset picture will come out of  
the projector’s speakers.  
on the projector or  
For details of the Resize mode, see pages 48  
and 49.  
You can also press  
on the remote control  
to change the resize mode. (See page 48.)  
While the “Pict in Pict” function is working, the  
“FREEZE” function only works for the inset picture.  
The “Pict in Pict” function does not work when the  
following signals are input to the main picture.  
UXGA/SXGA+/SXGA/WXGA signal  
480I/480P/540P/576I/576P/720P/1035P/1080I signal  
Interlaced RGB signal  
All signals (when “Resizeis set to “Dot by Dot”)  
No signal (or when the resolution or refresh rate  
(vertical frequency) of the signal is changed)  
-74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Shifting the Projected Im-  
age Vertically (Digital  
Shift)  
Setting On-screen Display  
This function allows you to turn the on-screen  
messages on or off.  
Menu operation  
Page 58  
For easier viewing, this function shifts the im-  
age projected on the screen up or down elimi-  
nating either the upper or lower black band found  
in 16:9 and other wide aspect ratios.  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Menu operation  
Page 56  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Description of OSD Display Settings  
Selectable items  
Description  
All on-screen displays are displayed.  
INPUT/VOLUME/MUTE/BLACK SCREEN/  
FREEZE/AUTO SYNC/ENLARGE/ “An in-  
valid button has been pressed.are not dis-  
played.  
All on-screen displays are not displayed.(ex-  
cept the menu, H & V LENS SHIFT, KEY-  
STONE, FOCUS, ZOOM, “All buttons on Pro-  
jector are locked.and warning displays)  
Normal  
Level A  
Level B  
Description of Digital Shift  
Press \  
Shifts the projected image Shifts the projected image  
down. up.  
Press |  
Note  
Note  
The “Digital Shift” function works with the  
“NORMAL, “BORDER”, “STRETCH” or “SMART  
STRETCH” image. (See page 49.)  
While “Keylock Level” is “Level A” or “Level B”,  
pressing displays “All buttons on  
Projector are locked.despite the “OSD Display”  
setting.  
-75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the “Options (1)” Menu  
Setting the Video System  
Capturing Projected Images  
The video input system mode is factory preset  
to “Auto”; however, a clear picture from the con-  
nected audio-visual equipment may not be re-  
ceived, depending on the video signal difference.  
In that case, switch the video signal.  
This projector allows you to capture projected  
images (RGB signals) and set them as a startup  
image, or background image when no signals are  
being received.  
Menu operation  
Page 58  
Menu operation  
Page 58  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Example: “Options (1)” screen menu for  
INPUT 4 (video) mode  
Description of Video Systems  
Selectable items  
PAL (50/60 Hz) When connected to PAL video equipment.  
Description  
Note  
SECAM  
NTSC4.43  
When connected to SECAM video equipment.  
When reproducing NTSC signals in PAL  
video equipment.  
Images can be captured only when they are  
from XGA (1024 × 768) non-interlace signals in  
INPUT 1, INPUT 2 or INPUT 3 mode with  
“RESIZE” set to “Normal”.  
NTSC3.58  
When connected to NTSC video equipment.  
The saved image is reduced to 256 colors.  
Images from equipment connected to INPUT 4  
or INPUT 5 terminal cannot be captured.  
Only one image can be captured and saved.  
The color of images may differ before and after  
saving if an image is captured on which image  
adjustment has been performed using the  
“C.M.S.” function.  
Note  
The video signal can only be set in INPUT 4 or  
INPUT 5 mode.  
When “Video System” is set to “Auto”, you may  
not receive a clear picture due to signal differ-  
ences. Should this occur, switch to the video  
system of the source signal.  
While “Video System” is set to “Auto”, when  
PAL-M or PAL-N signal is input, the image from  
PAL signal will be displayed.  
To delete the captured image, select “Delete”,  
and then press  
.
-76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Background  
Image  
Selecting the Startup Image  
Menu operation  
Page 58  
Menu operation  
Page 58  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Description of Startup Images  
Selectable items  
Logo  
Description  
Description of Background Images  
Default image  
Selectable items  
Logo  
Description  
Custom  
None  
User customized image (e.g. company logo)  
Black screen  
Default image  
Custom  
Blue  
User customized image (e.g. company logo)  
Blue screen  
None  
Black screen  
Note  
You can set a captured image as a startup im-  
age by selecting “Custom”.  
When “Custom” is selected, an image saved  
using “Image Capture” can be displayed as a  
startup image.  
Note  
You can set a captured image as a background  
image by selecting “Custom”.  
When “Custom” is selected, an image saved us-  
ing “Image Capture” can be displayed as a back-  
ground image.  
-77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the “Options (1)” Menu  
Eco Mode  
Detecting the Input Sig-  
nals Automatically  
Menu operation  
Page 56  
Menu operation  
Page 56  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Description of Eco Mode  
Power consumption  
(When using AC 100V)  
Description of Auto Search  
Selectable items  
ON  
Brightness  
Lamp life  
Selectable items  
Description  
Approx.  
86%  
Approx.  
2,500 hours*  
ON  
Automatically searches for and switches to  
the input mode in which signals are being  
received.  
Approx. 570 W  
Approx.  
2,000 hours*  
100%  
650 W  
OFF  
OFF  
“Auto Search” does not function.  
* This is a reference value and is not guaranteed.  
Note  
Note  
While the “Auto Search” function is detecting  
the input signal, pressing a button on the pro-  
jector or the remote control stops the “Auto  
Search” function. After the “Auto Search” func-  
tion finishes completely, press the desired button.  
When “Eco Mode” is set to “ON”, the power con-  
sumption will decrease and the lamp life will  
extend. (Projection brightness decreases ap-  
proximately 14%.)  
-78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auto Power Off Function  
System Lock Function  
This function prevents unauthorized use of the pro-  
jector. Once this function is activated, users must enter  
the correct keycode each time the projector is turned  
on.We suggest you record the keycode in a safe place  
where only authorized users have access.  
Menu operation  
Page 56  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Info  
If you lose or forget your keycode, contact your near-  
est Sharp Authorized Projector Dealer or Service  
Center (see page 104).Even if the product warranty  
is valid, the keycode reset will incur a charge.  
Menu operation  
Page 58  
Example: “Options (1)” screen menu for  
INPUT 1 (RGB) mode  
Description of Auto Power Off  
Selectable items  
Description  
ON  
The projector automatically enters the  
standby mode when no input signal is  
detected for 15 minutes or longer.  
The “Auto Power Off” function will be  
disabled.  
OFF  
Note  
When “Auto Power Off” is set to “ON”, 5 min-  
utes before the projector enters the standby  
mode, the message “Enter STANDBY mode in  
X min.” will appear on the screen to indicate  
the remaining minutes.  
Setting the keycode  
1 Select “System Lock” on the “Op-  
tions (1)” menu, then press |.  
A message is displayed.  
Read this message, and press  
.
2 Press the 4 buttons on the remote  
control or on the projector to enter  
the preset keycode in “Old Code”.  
When setting the keycode for the first time,  
press " on the projector for four times.  
-79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the “Options (1)” Menu  
Changing the keycode  
Note  
If you input a wrong keycode, the cursor returns  
to the first point of the “Old Code”.  
The preset keycode is 4 " buttons on the projec-  
tor.If this keycode is set, the keycode input screen  
does not appear when turning the power on.  
3 Press the 4 buttons on the remote  
control or on the projector to enter  
1 Press the 4 buttons on the remote  
control or on the projector to enter  
the preset keycode in “Old Code”.  
the new keycode in “New Code”.  
Note  
2
Press the 4 buttons on the remote  
control or on the projector to enter  
the new keycode in “New Code”.  
You cannot use the following buttons for  
keycode:  
ON button  
STANDBY button  
ENTER button  
L-click button  
R-click/UNDO button  
MENU button  
3 Enter the same keycode in “Recon-  
firm”.  
ZOOM buttons  
FOCUS buttons  
H & V LENS SHIFT button  
System Lock function recognizes each but-  
ton on the remote control or on the projec-  
tor as an individual button, even if they share  
the same button name. If you set the keycode  
with the buttons on the projector, use only  
those buttons on the projector. If you set the  
keycode with the buttons on the remote con-  
trol, use only those buttons on the remote  
control.  
4 Enter the same keycode in “Recon-  
firm”.  
Note  
Not displaying the keycode input screen  
when turning the projector on  
Press " on the projector for four times in steps  
2 and 3 above.  
When the System Lock is set  
When System Lock is set, the keycode input  
screen appears after the power is turned on.  
When it appears, enter the right keycode to start  
projection. Failure to enter the keycode will  
cause images not to be projected even when  
signals are entered to the projector.  
-80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When the system lock is set  
If you have set the system lock, enter the  
keycode and follow the procedure below to  
release the system lock.  
Input screen for keycode  
Note  
When System Lock is set, the keycode input  
screen appears after the power is turned on.  
If no keycode is entered, the image will not be  
displayed, even if the projector receives the in-  
put signal.  
1 Press  
on the remote control or  
on the projector to turn on the  
projector.  
2 When the keycode input screen ap-  
pears, enter the right keycode to  
start projection.  
Note  
System Lock function recognizes each but-  
ton on the remote control or on the projector  
as an individual button, even if they share  
the same button name. If you set the keycode  
with the buttons on the projector, use only  
those buttons on the projector. If you set the  
keycode with the buttons on the remote con-  
trol, use only those buttons on the remote  
control.  
-81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Functions Set during Installation (“Options (2)” menu)  
Changing the password  
Setting a Password  
There is no factory preset for the password, so  
the “Options (2)” menu is enabled.  
If you do not want others to operate the “Op-  
tions (2)” menu, set a password.  
Menu operation  
Page 58  
1
2
3
Press ', " and | to enter the pass-  
word in “Old Password” and press  
.
Example: “Options (2)” screen menu  
Press ', " and | to set the new  
password in “New Password” and  
press  
.
Enter the same 4-digit password in  
“Reconfirm” and press  
.
Note  
If you do not want to set a password, leave the  
fields blank in steps 2 and 3 and press  
.
To cancel the password settings, press  
.
1 Select “Password” from the “Op-  
If You Forget Your Password  
tions (2)” menu, and press |.  
If you forget the password, delete it using the fol-  
lowing procedure and set a new password.  
2 Press ' or " to set the first digit in  
Press  
.
“New Password” and then press |.  
3 Enter the remaining 3 digits and  
press  
.
4
Enter the same password inRecon-  
firm” and press  
.
Info  
The password must be entered to use the  
“Options (2)” menu when a password has  
been set.  
-82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking the Lamp Life  
Status  
Setting the Lamp Mode  
This function allows you to select the usage of  
the two lamps installed in the projector.  
You can confirm the cumulative lamp usage time  
and the remaining lamp life (percentage).  
Menu operation  
Page 58  
Menu operation  
Page 56  
Example: “Options (2)” screen menu  
Example: “Options (2)” screen menu  
Description of Lamp Mode  
Selectable items  
Both Lamps  
Description  
Both lamps are used for greater  
brightness.  
Description of Lamp Timer (Life)  
Remaining lamp life  
Lamp usage condition  
Lamp 1 Only  
The lamp 1 is used.  
100%  
5%  
When the lamp 1 burns out, the lamp 2  
automatically switches in use.  
The lamp 2 is used.  
When the lamp 2 burns out, the lamp 1  
automatically switches in use.  
Both lamps are used alternately for  
certain periods.  
Operated exclusively  
while “Eco Mode” is  
“ON”.  
Operated exclusively  
while “Eco Mode” is  
“OFF”.  
Approx.  
2,500 hours* 125 hours*  
Approx.  
Lamp 2 Only  
Equal Use  
Approx.  
2,000 hours* 100 hours*  
Approx.  
* This is a reference value and is not guaranteed.  
Note  
It is recommended that the lamp be changed  
when the remaining lamp life becomes 5%.  
The table above indicates rough estimates in the  
case of using only in each mode shown.  
The lamp life may vary depending on the usage  
condition.  
-83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Functions Set during Installation (“Options (2)” menu)  
Reversing/Inverting Pro-  
jected Images  
Controlling Multiple Projectors  
with the One Remote Control  
This function allows you to control multiple projectors  
with the one remote control during the stack projec-  
tion or the video wall projection.When using this func-  
tion, connect the projectors with LAN cables and as-  
sign a projector as the master and the other projectors  
as the slaves. See page 35 for connecting LAN cables.  
This projector is equipped with a reverse/invert  
image function that allows you to reverse or in-  
vert the projected image for various applications.  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Description of PRJ Modes  
Selectable items  
Description  
Normal image  
Ceiling + Front Inverted image  
Rear  
Reversed image  
Description of Stack Setting  
Front  
Selectable items  
Description  
Normal  
Master  
Slave  
The stack setting is not available.  
Set the projector as the master.  
Set the projector as the slave.  
Ceiling + Rear Reversed and inverted image  
Note  
Note  
This function is used for the reversed image and  
ceiling-mount setups. (See page 23.)  
When controlling multiple projectors with the one  
remote control, settings via web browser are required.  
Refer to the “SETUP MANUALcontained on the  
supplied CD-ROM for details.  
Only when controlling two projectors with the one  
remote control, using “Pair Stack” allows you to skip  
settings via web browser. (See page 85.)  
When “Slave” is selected on “Stack Setting”, the slave  
projector cannot be controlled with the remote control.  
To control the slave projector with the remote control,  
connect the remote control to the projector. (See page 18.)  
-84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Shortcut to Make Projector  
Stack Settings  
Locking the Operation But-  
tons on the Projector  
Normally, settings via web browser are required for  
the stack projection. You can skip the settings via  
web browser by using “Pair Stack”, only when you  
use the two projectors for the stack projection.  
This function can be used to lock the use of cer-  
tain operation buttons on the projector.  
Menu operation  
Page 58  
Menu operation  
Page 56  
Example: “Options (2)” screen menu  
Note  
Before setting “Pair Stack”, select “Master” or  
“Slave” on “Stack Setting”.  
Example: “Options (2)” screen menu  
Description of Keylock Level  
Selectable items  
Description  
Normal  
Level A  
All operation buttons are functional.  
Only INPUT/VOLUME buttons on the  
projector are available.  
Level B  
All operation buttons on the projector  
are unavailable.  
1 Select “Pair Stack” on the “Option  
(2)” menu, and then press  
.
The confirmation screen will be displayed.  
2 Select “OK”, and then press  
.
The network settings of the projector will  
change as shown below.  
Master  
192.168.150.2  
255.255.255.0  
OFF  
Slave  
192.168.150.3  
255.255.255.0  
OFF  
IP Address  
Subnet Mask  
DHCP Client  
Gateway  
0.0.0.0  
0.0.0.0  
User Name  
Password  
(Reset)  
(Reset)  
(Reset)  
(Reset)  
Data Port  
10002  
10002  
-85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Functions Set during Installation (“Options (2)” menu)  
Bypassing Unused Input  
Selections  
Selecting the Fan Mode  
This function changes the fan rotation speed.  
This function allows you to skip the input mode  
that you rarely use.You can skip the input modes  
when pressing INPUT 1, 2, 3 button or INPUT 4, 5  
button on the projector.  
Menu operation Page 58  
Example: “Options (2)” screen menu  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Description of Fan Mode  
Selectable items  
Description  
Normal  
High  
Suitable for normal environments.  
Select this when using the projector at  
attitudes of approximately 1,500 meters  
(4,900 feet) or more.  
Description of Set Inputs  
Selectable items  
Description  
Sets the INPUT 1–5 mode selectable  
respectively.  
Sets the INPUT 1–5 mode unavail-  
able respectively.  
ON  
INPUT 1–5  
OFF  
Note  
When “Fan Mode” is set to “High”, the fan rota-  
tion speeds up, and the fan noise becomes  
louder.  
-86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Direct Power On Function  
Selecting the Transmis-  
sion Speed (RS-232C)  
Menu operation  
Page 56  
Make sure that both the projector and computer  
are set for the same baud rate.  
Example: “Options (2)” screen menu  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Description of Direct Power On  
Selectable items  
Description  
ON  
The projector automatically turns on  
when the power cord is plugged into  
the AC outlet or the breaker switch is  
turned on.  
Description of RS-232C  
OFF  
The projector is turned on manually  
(see page 37), and does not turn on  
automatically when the power cord is  
plugged into the AC outlet or the  
breaker switch is turned on.  
Selectable items  
Description  
9600 bps  
Transmission speed is slow.  
38400 bps  
115200 bps  
Transmission speed is rapid.  
Note  
Refer to the “SETUP MANUALcontained on  
the supplied CD-ROM for RS-232C Specifica-  
tions and Command Settings.  
Refer to the computer’s operation manual for  
instructions for setting the computer’s baud rate.  
-87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Functions Set during Installation (“Options (2)” menu)  
Monitor Output Settings  
LAN/RS232C Setting  
When the Monitor Out has been set to “Enable”,  
the monitor output is activated and power is con-  
sumed even in the standby mode. It is recom-  
mended that the Monitor Out be set to “Disable”  
when it is not connected. This reduces power  
consumption when the projector is in the standby  
mode.  
When the LAN/RS232C has been set toEnable”,  
the LAN/RS232C is activated and power is con-  
sumed even in the standby mode. It is recom-  
mended that the LAN/RS232C be set toDisable”  
when it is not connected. This reduces power  
consumption when the projector is in the standby  
mode.  
Menu operation  
Page 58  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Example: “Options (2)” screen menu  
Description of Monitor Out  
Description of LAN/RS232C  
Selectable items  
Description  
Selectable items  
Description  
The monitor output function is activated  
even if the projector is in standby mode.  
The monitor output function is switched off  
when the projector is in standby mode.  
The LAN/RS232C function is activated  
even if the projector is in standby mode.  
The LAN/RS232C function is switched off  
when the projector is in standby mode.  
Enable  
Enable  
Disable  
Disable  
Note  
When you want to control the projector using  
the LAN/RS232C function, select “Enable.”  
The item “LAN/RS232C” will be made unavail-  
able for setting when “Master” or “Slave” is se-  
lected on “Stack Setting”. (“LAN/RS232C” will  
be set to “Enableautomatically.) (See page 84.)  
-88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DHCP Client Setting  
TCP/IP Setting  
Set the TCP/IP manually.  
Connect the LAN cable before turning the pro-  
jector on. If not, the DHCP Client function does  
not work.  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
Menu operation  
Page 58  
Example: “Options (2)” screen menu  
1 Select “TCP/IP”, then press  
.
Description of DHCP Client  
2 Enter “IP Address” using ', ", |  
and \, then press  
Selectable items  
Description  
.
Obtains configuration parameters for  
TCP/IP network automatically.  
Sets the TCP/IP manually.  
ON  
OFF  
Note  
Select “ON” for “DHCP Client”. “Obtaining IP  
Address...appears, then the message “The  
network settings have been changed., IP Address,  
Subnet Mask and Gateway will be displayed.  
If the DHCP server is not available, “Could not  
obtain IP Address.appears.  
3 Enter “Subnet Mask” using ', ",  
| and \, then press  
.
In this case, set the TCP/IP manually. (See  
“TCP/IP Setting” at right.)  
-89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Functions Set during Installation (“Options (2)” menu)  
4 EnterGatewayusing ', ", | and  
\, then press  
.
Service Mode  
Only the service centers use the menu. Do not  
use the menu.  
Description of TCP/IP  
Selectable items  
IP Address  
Description  
Factory default setting:  
192.168.150.002  
Example: “Options (2)” screen menu  
Enter an IP address appropriate for the  
network.  
Subnet Mask  
Gateway  
Factory default setting:  
255.255.255.000  
Set the subnet mask to the same as that  
of the computer and equipment on the  
network.  
Factory default setting:  
000. 000. 000. 000  
* When not in use, set to:  
“000. 000. 000. 000”.  
Note  
Before setting “TCP/IP”, select “OFF” for “DHCP  
Client”.  
Confirm the existing network’s segment (IP ad-  
dress group) to avoid setting an IP address that  
duplicates the IP addresses of other network  
equipment or computers. If “192.168.150.002”  
is not used in a network with an IP address of  
“192.168.150.XXX”, you don’t have to change  
the projector IP address.  
For details about each setting, consult your net-  
work administrator.  
-90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Returning to the Default  
Settings  
This function allows you to initialize the settings  
you have made in the projector.  
Menu operation  
Page 56  
Example: “Options (2)” screen menu  
Note  
About the network settings  
“IP Address”, “Subnet Mask”, “Gateway” and  
other network setting items are initialized.  
The following items or menu cannot be initialized.  
“C. M. S.” menu  
“Lightness”, “Chroma” and “Hue” respectively  
saved for Custom 1-3 on the “C.M.S.menu.  
“Fine Sync” menu  
Special Modes  
“Options (1)” menu  
System Lock  
“Options (2)” menu  
Lamp Timer (Life)  
“Language” menu  
Image stored using “Image Capture”  
-91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Other Menus (“Language” and “Status” menus)  
Selecting the On-screen  
Display Language  
Overview of All Menu Set-  
tings  
The projector can switch the on-screen display  
language among 11 languages: English, German,  
Spanish, Dutch, French, Italian, Swedish, Portu-  
guese, Chinese, Korean or Japanese.  
This function can be used to display all the ad-  
justed settings as a list on the screen.  
Menu operation  
Page 56  
Menu operation  
Page 58  
Example: “Status” screen menu  
Example: “Language” screen menu  
-92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Cleaning the projector  
Cleaning the air vents and the intake vent cover  
Use a vacuum cleaner to clean dust from the ex-  
haust vent, the intake vents and the intake vent cover  
(on the bottom of the projector).  
Ensure the power cord is unplugged before clean-  
ing the projector.  
The cabinet as well as the operation panel is made  
of plastic. Avoid using benzene or thinner, as these  
can damage the finish on the cabinet.  
Do not use volatile agents such as insecticides on  
the projector.  
Info  
If you want to clean the air vents and the intake  
vent cover during projector operation, ensure  
Do not attach rubber or plastic items to the projec-  
tor for long periods.  
The effects of some of the agents in the plastic may  
cause damage to the quality or finish of the projector.  
you press  
on the projector or  
on the  
remote control and put the projector into standby  
mode.After the cooling fan has stopped, unplug  
the power cord from the AC socket and clean  
the air vents and the intake vent cover.  
Cleaning the exhaust and intake vents  
Mild detergent  
diluted with water  
Cleaning the intake vent cover  
Thinner  
Wax  
Wipe off dirt gently with a soft flannel cloth.  
When the dirt is hard to remove, soak a cloth in a  
mild detergent diluted with water, wring the cloth  
well and then wipe the projector.  
Strong cleaning detergents may discolor, warp or  
damage the coating on the projector. Make sure to  
test on a small, inconspicuous area on the projec-  
tor before use.  
Cleaning the lens  
Use a commercially available blower or lens clean-  
ing paper (for glasses and camera lenses) for clean-  
ing the lens. Do not use any liquid type cleaning  
agents, as they may wear off the coating film on the  
surface of the lens.  
As the surface of the lens can easily get damaged,  
be careful not to scrape or hit the lens.  
Note  
The air vents and the intake vent cover should be  
cleaned every 100 hours of use. Clean the air vents  
and the intake vent cover more often when the pro-  
jector is used in a dusty or smoky location.  
Ensure the intake vent cover is securely installed.  
The power will not turn on unless it is correctly in-  
stalled.  
Cleaning  
aper  
P
-93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance Indicators  
The warning lights on the projector indicate problems inside the projector.  
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate  
red, and the projector will enter the standby mode. After the projector has entered the standby  
mode, follow the procedures given below.  
Maintenance Indicators  
Power indicator  
Lamp indicators 1, 2  
Temperature warning indicator  
About the temperature warning indicator  
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,  
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will  
turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and  
then the projector will enter the standby mode. After “  
” appears, ensure you perform the measures  
described on page 95.  
About the lamp indicator  
“Change The Lamp. (LAMP 2)” is displayed when the remain-  
ing life of the lamp 2 becomes 5% or less.  
When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp. (LAMP 1/2)”  
will be displayed on the screen.  
When the percentage becomes 0%, it will change to “ ” (red), the lamp will automatically turn off. At  
this time, the lamp indicator will illuminate in red.  
If you try to turn on the projector a fourth time without replacing the lamp, the lamp whose life is 0%  
will not light up.  
-94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance indicator  
Problem  
Cause  
Possible solution  
Normal  
Abnormal  
Relocate the projector to an area  
with proper ventilation. (See page  
9.)  
Blocked air intake  
The internal  
temperature is  
abnormally high.  
Temperature  
warning  
indicator  
Cooling fan break-  
down  
Take the projector to your nearest  
Sharp Authorized Projector Dealer  
Internal circuit failure or Service Center for repair. (See  
Clogged air intake page 104.)  
Clogged intake vent Clean the air vents and the intake  
Red on  
(Standby)  
Off  
cover  
vent cover. (See page 93.)  
Disconnect the power cord from  
the AC outlet, and then connect it  
again.  
The lamp does  
not illuminate.  
The lamp is shut  
down abnormally.  
Red on  
Carefully replace the lamp. (See  
page 97.)  
Take the projector to your nearest  
Sharp Authorized Projector Dealer  
or Service Center for repair. (See  
page 104.)  
Green on  
Green blinks  
when the lamp  
is warming up.  
Lamp  
indicators  
1, 2  
Time to change  
the lamp.  
Remaining lamp life  
becomes 5% or less.  
The lamp does  
not illuminate.  
Red on  
(Standby)  
Burnt-out lamp  
Lamp circuit failure  
Please exercise care when  
replacing the lamp.  
Securely install the cover.  
If the power indicator blinks even  
when the intake vent cover is  
securely installed, contact your  
nearest Sharp Authorized Projector  
Dealer or Service Center for  
advice. (See page 104.)  
The power  
indicator blinks in The intake vent  
red when the  
projector is on.  
Power  
indicator  
Green on/  
Red on  
Red  
blinks  
cover is open.  
Info  
If the temperature warning indicator blinks and the projector enters the standby mode, the temperature  
warning indicator starts to illuminate. Check whether any of the ventilation holes are blocked (see page 10)  
and then try turning the power back on.Wait until the projector has cooled down completely before plugging  
in the power cord and turning the power back on. (At least 10 minutes.)  
If the power is turned off for a brief moment due to power outage or some other cause while using the  
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red  
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power  
cord in the AC outlet and then turn the power on again.  
The cooling fan keeps the internal temperature of the projector constant and this function is controlled  
automatically. The sound of the cooling fan may change during operation because the fan speed may  
change and this is not a malfunction.  
-95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp  
Lamp  
It is recommended that the lamp units (optional: AN-PH7LP1 and AN-PH7LP2) be replaced when the  
remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture  
and color quality.The lamp life (percentage) can be checked with the on-screen display. See page 83.  
Purchase a replacement lamp unit of type AN-PH7LP1 and AN-PH7LP2 from your place of purchase,  
nearest Sharp Authorized Projector Dealer or Service Center.  
IMPORTANT NOTE TO U.S. CUSTOMERS:  
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service  
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-  
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer  
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).  
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information  
www.lamprecycle.org or 1-800-BE-SHARP  
U.S.A. ONLY  
Caution Concerning the Lamp  
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp  
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface  
scratches or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition  
and the frequency of use. It is important to note that failure can often result in the bulb cracking.  
When the lamp indicator and on-screen display icon are illuminated, it is recommended that the  
lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.  
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In  
case of exposure to the gas, consult a doctor as soon as possible.  
Should the lamp break, there is also a possibility that glass particles may spread inside of the  
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector  
Dealer or Service Center to assure safe operation.  
Replacing the Lamp  
Caution  
Do not remove the lamp unit from the projector right after use.The lamp will be very hot and may cause burn  
or injury.  
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool  
before removing the lamp unit.  
Carefully change the lamp by following the instructions described in this section. *If you wish, you  
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.  
* If the new lamp does not illuminate after replacement, take your projector to the nearest Sharp Authorized  
Projector Dealer or Service Center for repair.  
-96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing and Installing  
the Lamp Unit  
Lamp unit 1  
AN-PH7LP1  
Optional  
accessories  
Info  
Ensure the lamp unit is removed using the  
handle. Ensure the glass surface of the  
lamp unit or the inside of the projector are  
not touched.  
Lamp unit 2  
AN-PH7LP2  
To avoid injury to yourself and damage to  
the lamp, make sure you carefully follow  
the steps below.  
Do not loosen other screws except for the  
lamp unit cover and lamp unit.  
STANDBY button  
(Only the silver screws are loosened.)  
1 Press  
on the projector or  
on the remote control to put  
the projector into standby mode.  
Wait until the cooling fan stops.  
Warning!  
Do not remove the lamp unit from the  
projector right after use.The lamp and  
parts around the lamp will be very hot  
and may cause burn or injury.  
2 Disconnect the power cord.  
Unplug the power cord from the AC  
socket.  
Leave the lamp until it has fully cooled  
down (about 1 hour).  
3 Remove the lamp unit cover.  
Loosen the user service screw (1) that  
secures the lamp unit cover.Remove the  
lamp unit cover (2).  
Power cord  
2
1
User service screw  
-97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Handle  
Regarding the Lamp  
4 Remove the lamp unit.  
Loosen the securing screws (two for  
each lamp) from the lamp unit. Hold the  
lamp unit by the handle and pull it in the  
direction of the arrow. At this time, keep  
the lamp unit horizontal and do not tilt it.  
Securing screws  
5 Insert the new lamp unit.  
Press the lamp unit firmly into the lamp  
unit compartment. Fasten the securing  
screws.  
AN-PH7LP1  
AN-PH7LP2  
Be sure that AN-PH7LP1 and AN-  
PH7LP2 are respective type.  
For Lamp 1  
Compartment for  
AN-PH7LP1  
6 Replace the lamp unit cover.  
Align the lamp unit cover and slide it to  
close. Then tighten the user service  
screw to secure the lamp unit cover.  
For Lamp 2  
Compartment for  
AN-PH7LP2  
Info  
If the lamp unit and lamp unit cover are not  
correctly installed, the power will not turn  
on, even if the power cord is connected to  
the projector.  
User service screw  
-98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Resetting the Lamp Timer  
Reset the lamp timer after replacing the lamp.  
Info  
To AC socket  
Make sure to reset the lamp timer only  
when replacing the lamp. If you reset the  
lamp timer and continue to use the same  
lamp, this may cause the lamp to become  
damaged or explode.  
Power cord  
1 Connect the power cord.  
Plug the power cord into the AC socket  
of the projector.  
ON button  
ENTER button  
MENU button  
2 Reset the lamp timer.  
For Lamp 1  
When you reset the timer for AN-  
PH7LP1, while simultaneously holding  
H&V LENS  
SHIFT  
button  
down  
and  
, press  
on the  
projector.  
“LAMP 1 100%” is displayed, indicating  
that the lamp timer is reset.  
For Lamp 2  
When you reset the timer for AN-  
PH7LP2, while simultaneously holding  
down  
and  
, press  
on the  
projector.  
“LAMP 2 100%” is displayed, indicating  
that the lamp timer is reset.  
-99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Compatibility Chart  
The table below lists signal codes that are compatible with the projector. When the images are distorted or  
cannot be projected, adjust the output signal of your computer and so forth while referring to the table below.  
Computer  
Multiple signal support  
Compatible with sync on green signal  
UXGA, SXGA+ and SXGA compatible in advanced  
intelligent compression  
AICS (Advanced Intelligent Compression and Ex-  
pansion System) resizing technology  
Horizontal Frequency: 15–126 kHz  
Vertical Frequency: 43–200 Hz  
Pixel Clock: 12–230 MHz  
Sync signal: Compatible with TTL level  
The following is a list of modes that conform to VESA. However, this projector supports other signals  
that are not VESA standards.  
PC/  
MAC/  
WS  
Vertical  
Frequency  
(Hz)  
PC/  
MAC/  
WS  
Vertical  
Frequency  
(Hz)  
Horizontal  
Frequency  
(kHz)  
Horizontal  
Frequency  
(kHz)  
VESA  
DVI  
VESA  
DVI  
Resolution  
Display  
Resolution  
Display  
Standard Support  
Standard Support  
27.0  
31.5  
37.9  
27.0  
31.5  
27.0  
31.5  
37.9  
27.0  
31.5  
37.9  
26.2  
31.5  
34.7  
37.9  
37.5  
43.3  
47.9  
53.0  
61.8  
78.5  
80.9  
100.4  
31.4  
35.1  
37.9  
44.5  
48.1  
46.9  
53.7  
56.8  
64.0  
77.2  
98.3  
102.1  
125.6  
35.5  
40.3  
48.4  
56.5  
58.1  
60.0  
68.7  
73.5  
77.2  
80.6  
98.8  
113.2  
60  
70  
1,280  
1,280  
1,280  
1,360  
1,366  
×
×
×
×
×
720  
768  
800  
768  
768  
45.0  
47.8  
62.7  
47.6  
47.8  
54.3  
64.0  
64.1  
67.5  
75.7  
77.3  
90.2  
54.8  
65.9  
67.4  
64.0  
74.6  
78.1  
80.0  
91.1  
108.4  
64.0  
74.7  
60  
60  
75  
60  
60  
60  
70  
72  
75  
80  
85  
100  
60  
72  
74  
60  
70  
74  
75  
85  
100  
60  
52  
640  
720  
×
×
×
350  
350  
85  
WXGA  
60  
70  
60  
640  
720  
400  
400  
70  
85  
1,152  
×
×
864  
882  
60  
×
70  
85  
Advanced  
Intelligent  
Compression  
50  
VGA  
60  
SXGA  
1,152  
1,280  
70  
PC  
72  
75  
85  
640  
× 480  
90  
Upscale  
×
1,024  
1,050  
100  
120  
150  
160  
200  
50  
SXGA+ 1,400  
UXGA 1,600  
×
PC  
75.0  
81.3  
87.5  
60  
65  
70  
56  
×
1,200  
60  
Intelligent  
Compression  
90.1  
93.8  
72  
75  
85  
70  
72  
75  
106.3  
SVGA 800  
×
600  
85  
MAC 13" VGA  
640  
×
×
480  
624  
34.9  
49.6  
48.4  
60.0  
67  
75  
60  
75  
Upscale  
True  
90  
MAC 16" SVGA 832  
100  
120  
150  
160  
200  
43  
MAC 19"  
XGA 1,024  
×
768  
MAC 21" SXGA 1,152  
×
870  
68.5  
78.1  
75  
72  
HP (WS)  
PC (WS)  
WS  
1,280  
×1,024  
Advanced  
Intelligent  
Compression  
60.0  
85.9  
60.9  
71.9  
60  
85  
66  
76  
1,280  
×
960  
900  
SXGA  
50  
SUN (WS)  
1,152  
×
60  
70  
72  
75  
True  
XGA 1,024  
×
768  
85  
90  
96  
100  
120  
140  
-100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
Depending on the notebook computer, the image cannot be displayed or noise may appear in simulta-  
neous (CRT/LCD) mode. In this case, turn off the LCD display on the notebook computer. For more  
details, refer to the operation manual of the notebook computer.  
When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.  
When projecting the RGB interlace signal using INPUT 1/2 with “Signal Type” set to “Auto” or “RGB”, the  
image may not be projected as desired. In this case, select either INPUT 4 (video) or INPUT 5 (S-video).  
DTV  
Signal  
480I/525  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
DVI Support (Compatible with HDCP)  
I
480P/525P  
15.7  
31.5  
33.8  
15.6  
31.3  
45.0  
37.5  
33.8  
33.8  
28.1  
60  
60  
60  
50  
50  
60  
50  
60  
60  
50  
540P  
576I/625  
I
576P/625P  
720P/750P  
720P/750P  
1035I/1125  
1080I/1125  
1080I/1125  
I
I
I
-101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Problem  
Check  
Page  
37  
Projector power cord is not plugged into the wall outlet.  
Power to the external connected devices is off.  
The selected input mode is wrong.  
45  
Cables incorrectly connected to side panel of the projector.  
Remote control batteries have run out.  
2736  
17  
27  
No picture and no sound  
or projector does not start.  
External output has not been set when connecting notebook computer.  
Cables incorrectly connected to the side panel of the projector.  
“Bright” is set to minimum position.  
2736  
60  
The “BLACK SCREEN” function is working.  
50  
Sound is heard but no  
picture appears.  
Image adjustments are incorrectly set.  
60  
(INPUT 1, INPUT 2, INPUT 3 only)  
Input signal type (RGB/Component) is incorrectly set.  
(INPUT 4, INPUT 5 only)  
63  
76  
Video Input system is incorrectly set.  
Color is faded or poor.  
Adjust the focus.  
The projection distance exceeds the focus range.  
40  
22  
There is fog on the lens. If the projector is carried from a cold  
room into a warm room, or if it is suddenly heated,  
condensation may form on the surface of the lens and the  
image will become blurred. Please set up the projector at least  
one hour before it is to be used. If condensation should form,  
remove the power cord from the wall outlet and wait for it to  
clear.  
(Computer Input only)  
Perform “Fine Sync” Adjustments. (“Clock” Adjustment)  
Perform “Fine Sync” Adjustments. (“Phase” Adjustment)  
Picture is blurred;  
noise appears.  
68  
68  
101  
2736  
46  
Turn off the LCD display of the notebook computer.  
Noise may appear depending on the computer.  
Cables incorrectly connected to side panel of the projector.  
Volume is set to minimum.  
46  
The “MUTE” function is working.  
The “Speaker” menu is set to “OFF”.  
73  
Picture appears but no  
sound is heard.  
An unusual sound is  
occasionally heard  
from the cabinet.  
If the picture is normal, the sound is due to cabinet shrinkage  
caused by room temperature changes. This will not affect  
operation or performance.  
Maintenance  
indicator illuminates or  
blinks in red.  
See “Maintenance Indicators”.  
94  
-102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Check  
Page  
85  
The projector cannot be If the “Keylock Level” menu is set to “Level A” or “Level B”, all or  
turned on or put into the  
standby mode using the  
ON or STANDBY button  
on the projector.  
specific buttons on the projector are unavailable. Use the  
remote control to operate the projector.  
All buttons on the  
projector and the remote  
control are unavailable.  
If the “Stack Setting” menu is set to “Slave” and the “Keylock  
Level” menu is set to “Level B”, all buttons on the projector and  
the remote control are unavailable. Connect the remote control  
to the projector, and then use the remote control to operate the  
projector.  
18  
84  
85  
Change the input signal type setting.  
Picture is green on  
INPUT 1or 2  
(COMPONENT).  
63  
Picture is pink (no green)  
on INPUT 1, 2 or 3  
(RGB).  
Picture is too bright and Image adjustments are incorrectly set.  
60  
whitish.  
The cooling fan  
becomes noisy.  
When temperature inside the projector increases, the cooling  
fan runs faster.  
9, 10  
93 95  
The lamp does not light The lamp indicator is illuminating in red.  
94  
up even after the  
projector turns on.  
Replace the lamp.  
The lamp suddenly turns  
off during projection.  
The image sometimes Cables incorrectly connected to the projector or the connected  
2736  
flickers.  
equipment works improperly.  
If this happens frequently, replace the lamp.  
97  
97  
The lamps take a long  
time to turn on.  
The lamps will eventually need to be changed.  
The lamps have reached the end of its life. Replace the lamps.  
Picture is dark.  
The remote control  
cannot be used.  
Operate the remote control while pointing it at the projector’s  
remote control sensor.  
The remote control may be too far away from the projector.  
If direct sunlight or a strong fluorescent light is shining on the  
projector’s remote control sensor, place the projector where it  
will not be affected by strong light.  
17  
The batteries may be depleted or inserted incorrectly. Make  
sure the batteries are inserted correctly or insert new ones.  
17  
This projector is equipped with a microprocessor. Its performance could be adversely affected by  
incorrect operation or interference. If this should happen, unplug the projector and plug it in again  
after more than 5 minutes.  
-103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For SHARP Assistance  
If you encounter any problems during setup or operation of this projector, first refer to the  
“Troubleshooting” section on pages 102 and 103. If this operation manual does not answer  
your question, please contact the SHARP Service departments listed below.  
U.S.A.  
Sharp Electronics Corporation  
1-888-GO-SHARP (1-888-467-4277)  
lcdsupport@sharpsec.com  
Benelux  
SHARP Electronics Benelux BV  
0900-SHARPCE (0900-7427723)  
Nederland  
http://www.sharplcd.com  
9900-0159 Belgium  
http://www.sharp.nl  
Canada  
Mexico  
Sharp Electronics of Canada Ltd.  
(905) 568-7140  
http://www.sharp.ca  
http://www.sharp.be  
http://www.sharp.lu  
Australia  
Sharp Corporation of Australia  
Pty. Ltd.  
1300-135-022  
Sharp Electronics Corporation Mexico  
Branch  
(525) 716-9000  
http://www.sharp.net.au  
http://www.sharp.com.mx  
New Zealand  
Singapore  
Sharp Corporation of New Zealand  
(09) 634-2059, (09) 636-6972  
http://www.sharp.net.nz  
Latin America Sharp Electronics Corp. Latin American  
Group  
(305) 264-2277  
www.servicio@sharpsec.com  
http://www.siempresharp.com  
Sharp-Roxy Sales (S) Pte. Ltd.  
65-226-6556  
ckng@srs.global.sharp.co.jp  
http://www.sharp.com.sg  
Germany  
U.K.  
Sharp Electronics (Europe) GMBH  
01805-234675  
http://www.sharp.de  
Hong Kong  
Taiwan  
Sharp-Roxy (HK) Ltd.  
(852) 2410-2623  
dcmktg@srh.global.sharp.co.jp  
http://www.sharp.com.hk  
Sharp Electronics (U.K.) Ltd.  
08705 274277  
http://www.sharp.co.uk/customersupport  
Sharp Corporation (Taiwan)  
0800-025111  
http://www.sharp-scot.com.tw  
Italy  
Sharp Electronics (Italy) S.P.A.  
(39) 02-89595-1  
http://www.sharp.it  
Malaysia  
U.A.E.  
Sharp-Roxy Sales & Service Co.  
(60) 3-5125678  
France  
Sharp Electronics France  
01 49 90 35 40  
hotlineced@sef.sharp-eu.com  
http://www.sharp.fr  
Sharp Middle East Fze  
971-4-81-5311  
helpdesk@smef.global.sharp.co.jp  
Spain  
Sharp Electronica Espana, S.A.  
93 5819700  
sharplcd@sees.sharp-eu.com  
http://www.sharp.es  
Thailand  
Korea  
Sharp Thebnakorn Co. Ltd.  
02-236-0170  
svc@stcl.global.sharp.co.jp  
http://www.sharp-th.com  
Switzerland  
Sweden  
Austria  
Sharp Electronics (Schweiz) AG  
0041 1 846 63 11  
cattaneo@sez.sharp-eu.com  
http://www.sharp.ch  
Sharp Electronics Incorporated of  
Korea  
(82) 2-3660-2002  
lcd@sharp-korea.co.kr  
http://www.sharpkorea.co.kr  
Sharp Electronics ( Nordic ) AB  
(46) 8 6343600  
vision.support@sen.sharp-eu.com  
http://www.sharp.se  
India  
Sharp Business Systems (India)  
Limited  
(91) 11- 6431313  
Sharp Electronics (Europe) GMBH  
Branch Office Austria  
0043 1 727 19 123  
service@sharp-oa.com  
pogats@sea.sharp-eu.com  
http://www.sharp.at  
-104  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Product type Multimedia Projector  
Model XG-PH70X (standard zoom lens attached)/XG-PH70X-N (no lens attached)  
Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/  
DTV480I/DTV480P/DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I  
Display device 0.7" DLP® chip × 1  
No. of dots: 786,432 dots (1,024 [H] × 768 [V])  
Standard zoom lens 1.2 × electric zoom/focus lens, F1.8–F2.0, f = 25.6–31.3 mm (standard equipment with XG-PH70X)  
Projection lamp 260 W × 2  
Component input (INPUT 1)/ 15-pin mini D-sub connector  
output (OUTPUT) signal Y: 1.0 Vp-p, sync negative, 75 terminated  
PB: 0.7 Vp-p, 75 terminated  
PR: 0.7 Vp-p, 75 terminated  
Horizontal resolution 750 TV lines (DTV720P)  
Component input (INPUT 2) BNC connector  
signal Y: 1.0 Vp-p, sync negative, 75 terminated  
PB: 0.7 Vp-p, 75 terminated  
PR: 0.7 Vp-p, 75 terminated  
RGB input (INPUT 1/2)/output 15-pin mini D-sub connector, 5 BNC connector: RGB separate/composite sync (TTL)/sync  
(OUTPUT) signal on green type analog input: 0–0.7 Vp-p, positive, 75 terminated  
Horizontal sync. signal: TTL level (positive/negative) or composite sync (Apple only)  
Vertical sync. signal: Same as above  
RGB digital input signal (INPUT 3) DVI connector (24-pin), RGB (digital), 250 –1,000 mV, 50 (Compatible with HDCP)  
Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω  
(INPUT 4) terminated  
S-video input signal 4-pin mini DIN connector  
(INPUT 5) Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated  
C (chrominance signal): Burst 0.286 Vp-p, 75 terminated  
Audio input signal ø3.5 mm stereo minijack, RCA terminal  
0.5 Vrms, more than 22 kΩ  
Audio output signal ø3.5 mm minijack  
(AUDIO OUTPUT 1–5) 0.5 Vrms, less than 2.2 kΩ  
RS-232C terminal 9-pin D-sub connector  
LAN terminal 8-pin RJ-45 modular connector  
Pixel clock 12–230 MHz  
Vertical frequency 43–200 Hz  
Horizontal frequency 15–126 kHz  
Audio output 3.0 W (stereo)  
Speaker system 3.3 cm round × 2  
Rated voltage AC 100–240 V  
Input current 6.6 A (AC 100 V)–2.7 A (AC 240 V)  
Rated frequency 50/60 Hz  
Power consumption 650 W (when “Eco Mode” is “OFF”)/570 W (when “Eco Mode” is “ON”) with AC 100 V  
620 W (when “Eco Mode” is “OFF”)/550 W (when “Eco Mode” is “ON”) with AC 240 V  
Power consumption (standby) 0.8 W (AC 100 V) – 1.1 W (AC 240 V) (When “Monitor Out” and “LAN/RS232C” are set to “Disable”.)  
Heat dissipation 2,440 BTU/hour (when “Eco Mode” is “OFF”)/2,140 BTU/hour (when “Eco Mode” is “ON”)  
with AC 100 V  
2,330 BTU/hour (when “Eco Mode” is “OFF”)/2,070 BTU/hour (when “Eco Mode” is “ON”)  
with AC 240 V  
Operating temperature 41°F to 104°F (+5°C to +40°C)  
Storage temperature –4°F to 140°F (–20°C to +60°C)  
Cabinet Plastic  
I/R carrier frequency 38 kHz  
Dimensions (approx.) 16 5/32" × 7 3/32" × 18 35/64" (410 (W) × 180 (H) × 471 (D) mm) (main body only)  
16 5/32" × 7 37/64" × 18 35/64" (410 (W) × 192.1 (H) × 471 (D) mm) (including adjustment foot  
and projecting parts)  
Weight (approx.) XG-PH70X: 32.9 lbs. (14.9 kg)  
XG-PH70X-N: 30.3 lbs. (13.7 kg)  
Replacement parts Remote control, Power cord for U.S., Canada, etc., Power cord for Europe, except U.K.,  
Power cord for U.K., Hong Kong and Singapore, Power cord for Australia, New Zealand and  
Oceania, RGB cable, Remote mouse receiver, Cap for the standard zoom lens, Projector  
manual and technical reference CD-ROM, Operation manual  
As a part of policy of continuous improvement, SHARP reserves the right to make design  
and specification changes for product improvement without prior notice. The performance  
specification figures indicated are nominal values of production units. There may be some  
deviations from these values in individual units.  
-105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary  
Advanced intelligent compression (Page 100)  
High quality resizing of lower and higher resolu-  
tion images to fit the projector’s native resolution.  
Picture Mode (Page 60)  
Image quality enhancement function that offers a  
richer image by brightening the darker portions  
of the image without altering the brightness of the  
brighter portions. You can select four different  
modes: STANDARD, PRESENTATION, CINEMA  
and CUSTOM.  
Aspect ratio (Page 48)  
Width and height ratio of an image. The normal  
aspect ratio of a computer and video image is 4:3.  
There are also wide images with an aspect ratio  
of 16:9 and 21:9.  
Progressive (Page 62)  
The progressive display projects a smoother video  
image. You can select three different modes: 2D  
Progressive, 3D Progressive and Film Mode.  
Auto Sync (Page 70)  
Optimizes projected computer images by auto-  
matically adjusting certain characteristics.  
Resize (Page 48)  
Background (Page 77)  
Allows you to modify or customize the picture dis-  
play mode to enhance the input image. You can  
select six different modes: NORMAL, FULL, DOT  
BY DOT, BORDER, STRETCH and SMART  
STRETCH.  
Initial setting image projected when no signal is  
being output.  
Border (Page 48)  
Projects a 4:3 image fully within a 16:9 screen by  
keeping the aspect ratio at 4:3.  
Shifting the lens (Page 38)  
Function to adjust the position of the projected im-  
age for the position of the screen by shifting the lens  
horizontally and vertically.  
Clock (Page 68)  
Clock adjustment is used to adjust vertical noise  
when clock level is incorrect.  
Smart Stretch (Page 49)  
CLR Temp (Color temperature) (Page 61)  
Function that can be used to adjust the color tem-  
perature to suit the type of image input to the pro-  
jector. Decrease the color temperature to create  
warmer, reddish images for natural flesh tones,  
or increase to create cooler, bluish images for a  
brighter picture.  
Projects the image fully in a 16:9 screen by en-  
larging only the surrounding areas while keeping  
the aspect ratio in the middle part of the image at  
4:3.  
sRGB (Page 64)  
An international standard of color reproduction  
regulated by the IEC (International Electrotechnical  
Commission). As the fixed color area has been  
decided by the IEC, the color changes according  
to DLP features, so that the images are displayed  
in a natural tint based on an original image, when  
“C.M.S. Adjustment” is set to “sRGB”.  
C.M.S. (Color Management System) (Page 64)  
Function allows you individually adjust the display  
characteristics of six colors (R: Red, Y:Yellow, G:  
Green, C: Cyan, B: Blue, M: Magenta)  
Dot by Dot (Page 48)  
Mode that projects images in their native resolution.  
Keylock Level (Page 85)  
Stack Setting (Page 84)  
Mode that can lock the operation of projector but-  
tons to prevent unauthorized adjustment.  
Setting for the stack projection that allows you to  
increase the brightness of an image by stacking  
multiple projectors and projecting same image  
simultaneously.You can control projectors for the  
stack projection by assigning a projector as the  
master and the other projectors as the slaves.  
Keystone Correction (Page 41)  
Function to digitally correct a distorted image  
when the projector is set up at an angle, smooth-  
ens out jaggies on keystone images and com-  
presses the image not only horizontally but verti-  
cally keeping the 4:3 aspect ratio.  
Stretch (Page 48)  
Mode that stretches the 4:3 image horizontally to  
display it fully on a 16:9 screen.  
Phase (Page 68)  
System Lock (Page 79)  
Phase shift is a timing shift between isomorphic  
signals with the same resolution.When phase level  
is incorrect, the projected image typically displays  
horizontal flicker.  
If the “Keycode” set in the projector is not cor-  
rectly entered, the projector will not operate even  
if signals are entered.  
Pict in Pict (Page 74)  
The Pict in Pict (picture in picture) function allows  
you to display two pictures on the same screen.  
You can display the image input from a video as  
an inset picture overlapping the main picture in-  
put from a computer.  
-106  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
AC socket ....................................................................... 37  
ADJ./MOUSE switch ...................................................... 18  
Adjustment buttons ........................................................ 56  
Adjustment feet .............................................................. 39  
Advanced intelligent compression .............................. 100  
All Reset ........................................................................ 91  
Aspect ratio .................................................................... 48  
Audio .............................................................................. 72  
AUDIO input (1) terminal ............................................... 27  
AUDIO input (2, 3) terminal ........................................... 28  
AUDIO input (4, 5) terminals ......................................... 34  
Audio Out ....................................................................... 72  
AUDIO OUTPUT terminal ............................................. 36  
Auto Power Off............................................................... 79  
Auto Search ................................................................... 78  
Auto Sync (Auto Sync adjustment) ............................... 70  
AUTO SYNC button ....................................................... 70  
Auto Sync Disp .............................................................. 71  
Lamp Timer (Life) .......................................................... 83  
Lamp unit cover ............................................................. 97  
LAN terminal .................................................................. 35  
LAN/RS232C ................................................................. 88  
Language ....................................................................... 92  
L-click button.................................................................. 19  
Lens cap ........................................................................ 13  
MENU button ................................................................. 56  
Monitor Out .................................................................... 88  
Mouse button ................................................................. 19  
MUTE button.................................................................. 46  
Network.......................................................................... 89  
Normal ........................................................................... 48  
ON button ...................................................................... 37  
Options (1) ..................................................................... 74  
Options (2) ..................................................................... 82  
OSD Display .................................................................. 75  
OUTPUT (FOR INPUT 1, 2) terminal ........................... 36  
Background.................................................................... 77  
BLACK SCREEN button ................................................ 50  
Border ............................................................................ 48  
BREAK TIMER button ................................................... 50  
Bright Boost ................................................................... 61  
Pair Stack....................................................................... 85  
Password ....................................................................... 82  
Phase ............................................................................. 68  
Pict in Pict ...................................................................... 74  
Picture............................................................................ 60  
Picture Mode ................................................................. 60  
PICTURE MODE button ................................................ 47  
Power cord ..................................................................... 37  
Power indicator .............................................................. 14  
PRJ Mode ...................................................................... 84  
Progressive .................................................................... 62  
C.M.S. (Color Management System) ............................ 64  
C.M.S. Adjustment ......................................................... 64  
Carrying handle ............................................................. 13  
Clock .............................................................................. 68  
CLR Temp (Color Temperature) .................................... 61  
DHCP Client .................................................................. 89  
Digi. Shift........................................................................ 75  
Direct Power On ............................................................ 87  
DNR ............................................................................... 62  
Dot By Dot ..................................................................... 48  
R-click button ................................................................. 19  
Remote control .............................................................. 17  
Remote control sensor .................................................. 17  
Remote mouse receiver ................................................ 19  
Resize ............................................................................ 48  
RESIZE button ............................................................... 48  
RGB cable ..................................................................... 27  
RS-232C ........................................................................ 87  
RS-232C terminal .......................................................... 35  
Eco Mode....................................................................... 78  
ENLARGE buttons......................................................... 46  
ENTER button................................................................ 56  
Exhaust vent .................................................................. 93  
Fan Mode ....................................................................... 86  
Fine Sync ....................................................................... 68  
FOCUS buttons ............................................................. 40  
FREEZE button ............................................................. 47  
Save Setting .................................................................. 68  
Select Setting ................................................................ 69  
Service Mode................................................................. 90  
Set Inputs....................................................................... 86  
Signal Info ...................................................................... 70  
Signal Type .................................................................... 63  
Smart Stretch ................................................................ 49  
Speaker.......................................................................... 73  
Special Modes ............................................................... 69  
sRGB ............................................................................. 64  
Stack Setting ................................................................. 84  
STANDBY button ........................................................... 37  
Startup Image ................................................................ 77  
Status ............................................................................. 92  
Stretch ........................................................................... 48  
Subnet Mask .................................................................. 90  
System Lock .................................................................. 79  
Gateway ......................................................................... 90  
Geometric adjustment ................................................... 42  
H & V keystone .............................................................. 43  
H & V LENS SHIFT button ............................................ 39  
Image Capture ............................................................... 76  
Image resizing ............................................................... 44  
INPUT 1 – 5 modes ....................................................... 45  
INPUT 1 terminal ........................................................... 27  
INPUT 2 terminals ......................................................... 28  
INPUT 3 terminal ........................................................... 29  
INPUT 4 terminal ........................................................... 34  
INPUT 5 terminal ........................................................... 34  
INPUT buttons ............................................................... 45  
Intake vent ..................................................................... 93  
IP Address ..................................................................... 90  
TCP/IP ........................................................................... 89  
Temperature warning indicator ...................................... 94  
Kensington Security Standard connector ..................... 15  
Keycode ......................................................................... 79  
Keylock Level ................................................................. 85  
KEYSTONE button ........................................................ 41  
Keystone Correction ...................................................... 41  
UNDO button ................................................................. 56  
Video System ................................................................ 76  
Volume buttons .............................................................. 46  
WIRED R/C JACK ......................................................... 18  
WIRED REMOTE terminal ............................................ 18  
Lamp .............................................................................. 96  
Lamp indicators 1, 2 ...................................................... 94  
Lamp Mode .................................................................... 83  
ZOOM buttons ............................................................... 40  
-107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHARP CORPORATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Microphone EW 300 Series User Manual
Sharp CRT Television 27C240 User Manual
Sharp Printer AL 2050CS User Manual
Sony Car Video System XVM R75 User Manual
Sony MP3 Player RCD W7V User Manual
Sony Security Camera SNC CS50N User Manual
Sony Security Camera SNC DH110 User Manual
Sony VCR SLV 675HF User Manual
Sterling Weather Radio 6312 C User Manual
Sylvania CRT Television C6413TD C5419TD User Manual