DATA PROJECTOR
MODEL
XG-P610X
(Standard zoom lens attached)
XG-P610X-N
(No lens attached)
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
See side of projector.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
to constitute a risk or electric shock to
SERVICE SCREW.
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
persons.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For
disposal or recycling information, please contact your local authorities, the Electronics
or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 71.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 pixels (micromirrors). As
with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
• DLP® and the DLP logo are registered trademarks of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru-
ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse as-
semble or discompile the contents thereof.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
E.U. ONLY
Sonninstraße 3, D-20097 Hamburg
-2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read This Operation Manual
• In this operation manual, the illustrations and on-screen displays are simplified for explana-
tion.This may differ from the actual on-screen display.
Using the Menu Screen
MENU button
Adjustment
buttons ('/"/\/|)
ENTER button
Buttons used in this
operation
MENU button
Mouse/adjustment
Buttons used in this
operation
button ('/"/\/|)
UNDO button
ENTER button
UNDO button
Menu Selections
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu for
COMPUTER1 (RGB) mode
1
2
Press MENU.
Button used in
this step
• The “Picture” menu screen for the se-
lected input mode is displayed.
Press \or |to display the other
menu items.
Menu items
On-screen display
• Menu items are as shown below.
Menu item
Note
• The “Fine Sync” menu is not available
for VIDEO or S-VIDEO.
-47
Info
...........Indicates safeguards when using the projector.
........Indicates additional information for setting up and operating the projector.
Note
For Future Reference
Maintenance
Troubleshooting
Index
Page 66
Pages 79 and 80
Page 83
-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
How to Read This Operation Manual ............ 3
Contents.......................................................... 4
How to Access the PDF
Operation Manuals ................................... 7
IMPORTANT SAFEGUARDS .......................... 8
Accessories .................................................. 11
Part Names and Functions .......................... 13
Using the Remote Control ........................... 16
Usable Range .................................................... 16
Inserting the Batteries ....................................... 16
Using the Remote Control with
a Signal Cable ............................................. 17
Switching the Remote Control Mode ................. 17
Using the Remote Control as
a Wireless Computer Mouse ....................... 18
Quick Start
Quick Start .................................................... 19
Setup
Setting Up the Projector .............................. 21
Setting Up the Projector .................................... 21
Standard Zoom Lens (AN-P18EZ : Standard
Equipment with XG-P610X) ......................... 22
Projecting a Reversed Image ............................ 23
Connections
Connecting the Projector to Other
Equipment ............................................... 24
Controlling the Projector by a Computer ... 27
Using
Basic Operation
Correcting Trapezoidal Distortion ...................... 32
Switching the Input Mode .................................. 36
Adjusting the Volume ......................................... 36
Turning Off the Sound Temporarily .................... 37
Displaying an Enlarged Portion of an Image..... 37
Freezing a Moving Image .................................. 38
Selecting the Picture Mode ............................... 38
Resize Mode ...................................................... 39
Hiding the Projected Image
Turning the Projector On/Off....................... 28
Connecting the Power Cord .............................. 28
Turning the Projector On.................................... 28
Turning the Power Off (Putting the Projector
into Standby Mode) ..................................... 28
Image Projection .......................................... 29
Shifting the Lens ................................................ 29
Using the Adjustment Feet ................................ 30
Adjusting the Focus ........................................... 31
Adjusting the Projected Image Size .................. 31
(Shutter function) ......................................... 41
Displaying and Setting the Break Timer ............ 41
-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Features
Shifting the Projected Image Vertically
Menu Items ................................................... 42
Using the Menu Screen ............................... 47
Menu Selections ................................................ 47
Picture Adjustment (“Picture” menu)......... 49
Selecting the Picture Mode ............................... 49
Adjusting the Image .......................................... 49
Adjusting the Color Temperature ....................... 50
Selecting the Progressive Mode........................ 50
Reducing Image Noise (DNR)........................... 50
Selecting the Signal Type .................................. 51
Selecting the Dynamic Range ........................... 51
Selecting the Color Space................................. 51
Color Management System
(Digital Shift) ................................................ 57
Setting On-screen Display................................. 57
Setting the Video System................................... 57
Capturing Projected Images ............................. 57
Selecting the Background Image ...................... 58
Selecting the Startup Image .............................. 58
Setting the Eco Mode ........................................ 58
Detecting the Input Signals Automatically ........ 58
Setting the Auto Power Off Function.................. 58
Setting the System Lock Function ..................... 59
Helpful Functions Set during Installation
(“Options 2” menu)................................. 61
Setting a Password ............................................ 61
Setting the Lamp Mode ..................................... 62
Selecting the Lens Type .................................... 62
Reversing/Inverting Projected Images .............. 62
Controlling Multiple Projectors with the One
(“C. M. S.” menu) ..................................... 52
Selecting the Color Reproduction Mode ........... 52
Selecting the Target Color ................................. 52
Setting the Brightness of the Target Color ......... 52
Setting the Chromatic Value of
Remote Control ........................................... 62
Shortcut to Make Projector Stack Settings ........ 63
Locking the Operation Buttons
on the Projector ........................................... 63
Bypassing Unused Input Selections ................. 63
Selecting the Fan Mode .................................... 63
Setting the Auto Restart Function ...................... 63
Selecting the Transmission Speed
the Target Color ........................................... 52
Setting the Hue of the Target Color ................... 52
Resetting User-defined Color Settings .............. 52
Overview of All Color Settings ........................... 52
Computer Image Adjustment
(“Fine Sync” menu) ................................ 53
Adjusting the Computer Image ......................... 53
Saving Adjustment Settings .............................. 53
Accessing Adjustment Settings ........................ 53
Setting the Resolution........................................ 53
Checking the Input Signal ................................. 54
Auto Sync Adjustment ....................................... 54
Setting the Auto Sync Display Function ............ 54
Audio Adjustment (“Audio” menu) ............. 55
Adjusting the Audio ........................................... 55
Setting the Audio Output Type .......................... 55
Setting the Speaker ........................................... 55
Using the “Options 1” Menu ........................ 56
Displaying Dual Pictures (Pict in Pict) ............... 56
Setting the Resize Mode ................................... 56
(RS-232C) ................................................... 64
Setting the Monitor Output ................................ 64
Setting the LAN/RS232C ................................... 64
Setting the DHCP Client .................................... 64
Helpful Functions Set during Installation
(“Options 2” menu)/Using the Other Menus
(“Language” and “Status” menus) ............... 65
Setting the TCP/IP ............................................. 65
Service Mode .................................................... 65
Returning to the Default Settings....................... 65
Selecting the On-screen Display Language ..... 65
Overview of All Menu Settings and the Lamp Life .... 65
Reference
Appendix
Removing and Installing the Lamp Unit ............ 72
Resetting the Lamp Timer ................................. 74
Computer Compatibility Chart .................... 75
Attaching the Optional Lens ....................... 77
Troubleshooting ........................................... 79
For SHARP Assistance................................ 81
Specifications............................................... 82
Index .............................................................. 83
Maintenance ................................................. 66
Cleaning and Replacing the Dust Filters ... 67
Cleaning the Dust Filters ................................... 67
Replacing the Dust Filters ................................. 68
Maintenance Indicators ............................... 69
Regarding the Lamp .................................... 71
Lamp ................................................................. 71
Caution Concerning the Lamp .......................... 71
Replacing the Lamp .......................................... 71
The optional lenses are introduced on page 12. Please purchase the lens for your desired
usage.
-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Setting up the Screen .................................... 2
Screen Size and Projection Distance ........... 3
Connecting Pin Assignments ..................... 11
Wired Remote Control Terminal
Specifications ......................................... 13
RS-232C Specifications and Commands ... 14
Setting up the Projector Network
Environment............................................ 20
Controlling the Projector via LAN .............. 26
Setting the Projector Using
Controlling the Projector Using RS-232C
or Telnet ................................................... 34
Stack Projection ........................................... 41
Video Wall Projection ................................... 44
Resetting the Lamp Timer of the Projector
via LAN .................................................... 53
Troubleshooting ........................................... 55
Dimensions................................................... 58
RS-232C or Telnet ................................... 31
-6
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM, so that you can
work with the projector.To utilize these manuals, you need to install Adobe® Reader® on your
computer (Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF manuals
For Windows®:
For Macintosh®:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “CD-ROM” icon.
3
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
4
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the pro-
jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the pro-
jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the SETUP
MANUAL.
3) Double click the pdf file to access the SETUP
MANUAL.
Info
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then
specify the desired file using the “File”, “Open” menu.
-7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read before
the product is operated.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
14. Lightning
3. Heed Warnings
For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the cable
system. This will prevent damage to the product due to
lightning and power-line surges.
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
15. Overloading
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
6. Attachments
16. Object and Liquid Entry
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
9. Transportation
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, ensure that the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
12. Grounding or Polarization
This product is provided with one of the following types of
plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
21
.
Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ensure that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp rup-
tures. In case of lamp rupture, contact your
nearest Sharp Authorized Projector Dealer
or Service Center for replacement. See
“Regarding the Lamp” on page 71.
The projector may be safely tilted to a
maximum angle of 9 degrees.
■ Placement should be within 9 degrees of
horizontal.
If you have application requiring tilt angle
exceeding 9 degrees, please check with your
local Sharp sales office.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Caution concerning the setup of the pro-
jector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more
often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Warning about placing the projector in a
high position
■ When placing the projector in a high posi-
tion, make certain it is carefully secured to
avoid personal injury caused by the projec-
tor falling down.
Do not set up the projector in places ex-
posed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Do not subject the projector to hard im-
pact and/or vibration.
■ Take care with the lens so as not to hit or
damage the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of tem-
perature.
■ The operating temperature of the projector
is from 41°F to 104°F (+5°C to +40°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
-9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Do not block the intake and exhaust
vents.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Set up the projector where air will not stay
near its exhaust vent. In order to avoid allow-
ing the heat from the exhaust vent to enter
the intake vent area, leave at least more than
11 13/16 inches (30 cm) of space between the
intake vent and the surrounding walls or ob-
jects.
Temperature monitor function
■
If the projector starts to over-
heat due to setup problems or
blockage of the air vents, “
”
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (See pages 69 and 70.).Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes.Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
and “ ” will illuminate in
the lower left corner of the picture. If the tem-
perature continues to rise, the lamp will turn off,
the temperature warning indicator on the pro-
jector will blink, and after a 90-second cooling-
off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page 69 for details.
Info
• The cooling fan regulates the internal tem-
perature, and its performance is automati-
cally controlled.The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.
• Even if you unplug the power cord after
projector operation, the cooling fan con-
tinues to run for a while. When you place
the projector into the storage case, make
sure that the cooling fan has stopped.
Caution regarding usage of the projector
■
When using the projector, take care not to subject
it to hard impact and/or vibration, as this can result
in damage.Take extra care with the lens. If you are
not to use the projector for a long time, make cer-
tain you unplug the power cord from the wall outlet,
and disconnect any other cables connected to it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you at-
tach the lens cap or dustproof cap to the pro-
jector. (See page 13.)
■ Do not expose the projector to direct sunlight
or near heat sources. The projector may
change color or become deformed.
Optional lens installation
■ For installing an optional lens, refer to “At-
taching the Optional Lens” on page 77 or the
lens installation manual (supplied with the
optional lens).
Other connected equipment
■ When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the operation manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
■ Remove the optional lens when carrying the
projector. Carrying the projector with an op-
tional lens attached can cause the projector
to be damaged by vibration or other factors.
-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Remote control
Two R-6 batteries
<9NK5041816900>
(“AA” size, UM/SUM-3, HP-7 or similar)
Power cord*
(1)
(4)
(2)
(3)
For U.S., Canada, etc. For Europe, except U.K.
For U.K., Hong Kong For Australia, New
(6' (1.8 m))
<9NK3090204900>
(6' (1.8 m))
<9NK3090152700>
and Singapore
(6' (1.8 m))
Zealand and Oceania
(6' (1.8 m))
<9NK3090152900>
<9NK3090152600>
*Use the power cord that corresponds to the wall outlet in your country.
Lens cap
RGB cable
(Only supplied with XG-P610X)
<9NK3392072800>
Dustproof cap
• Projector manual and technical
reference CD-ROM
<9NK3534059900>
(10' (3.0 m))
<9NK3080431000>
(Only supplied with XG-P610X-N)
<9NK3392072900>
• Operation manual (this manual)
<9NK5010071200>
Note
• Codes in “< >” are Replacement parts codes.
• When the lens is attached, use the lens cap supplied with the lens.
• You can attach the dustproof cap to the projector only when no lens is attached. (Do not attach the
dustproof cap when the lens is attached.)
Optional accessories
■ Lamp unit
AN-P610LP
■ Ceiling-mount adaptor
■ Ceiling-mount unit
AN-P610T
AN-TK201
AN-TK202
AN-MR2
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10' (3.0 m))
AN-C3CP2
Note
• Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Optional lenses
■ Lens
Projection distance for 100" screen size
Fixed wide lens (× 0.8)
AN-P8EX
5'4" (1.6 m)
Fixed wide lens (× 1.2)
AN-P12EX
AN-P15EZ
AN-P18EZ
8' (2.4 m)
10' – 12' (3.0 m – 3.7 m)
12' – 15' (3.7 m – 4.6 m)
Wide-zoom lens (× 1.5 – 1.8)
Standard zoom lens (× 1.8 – 2.25)
(attached to XG-P610X)
Tele-zoom lens (× 2.25 – 3.0)
Tele-zoom lens (× 3.0 – 4.5)
Tele-zoom lens (× 4.5 –7.0)
AN-P23EZ
AN-P30EZ
AN-P45EZ
15' – 20' (4.6 m – 6.1 m)
20' – 30' (6.1 m – 9.1 m)
30' – 46'8" (9.1 m – 14.2 m)
No lens is attached to XG-P610X-N.The standard zoom lens is attached to XG-P610X.
The optional lenses from Sharp are also available for specialized application. Please see
your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the
lens operation manual when using a lens.)
Throw Distance
The graph below is for 100-inch (254 cm) screen with 4:3 normal mode.
Screen
Fixed wide lens (AN-P8EX)
5'4" (1.6 m)
Throw distance ratio 1:0.8
Fixed wide lens (AN-P12EX)
8' (2.4 m)
Throw distance ratio 1:1.2
Wide-zoom lens (AN-P15EZ)
10' – 12' (3.0 m – 3.7 m)
Throw distance ratio 1:1.5–1.8
Standard zoom lens (AN-P18EZ : Standard equipment with XG-P610X)
12' – 15' (3.7 m – 4.6 m)
Throw distance ratio 1:1.8–2.25
Tele-zoom lens (AN-P23EZ)
15' – 20' (4.6 m – 6.1 m)
Throw distance ratio 1:2.25–3.00
Tele-zoom lens (AN-P30EZ)
20' – 30' (6.1 m – 9.1 m)
Throw distance ratio 1:3.0–4.5
Tele-zoom lens (AN-P45EZ)
30' – 46' 8" (9.1 m – 14.2 m)
Throw distance ratio 1:4.5–7.0
5
10
15
20
25
30
35
40
45
50(ft)
-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector
Rear View
H&V LENS SHIFT button
For shifting the lens horizontally
and vertically.
30
32 KEYSTONE button
For entering the Keystone
Correction mode.
ON button 28
INPUT buttons
For turning the power on.
36
For switching input mode.
STANDBY button
For putting the projector
into standby mode.
28
31
MENU button
For displaying adjustment
and setting screens.
47
ZOOM buttons
For adjusting the projected
image size.
Volume buttons
For adjusting the speaker
sound level.
36
FOCUS buttons
For adjusting the focus.
31
ENTER button
For setting items selected
or adjusted on the menu.
47
47
47
UNDO button
For undoing an operation or
returning to the previous display.
SHUTTER buttons 41
• OPEN: For opening the shutter.
• CLOSE: For closing the shutter
and hiding the projected
Adjustment buttons
('/"/\/|)
For selecting menu items
and other settings.
image.
AUTO SYNC button
54
For automatically
adjusting images when
connected to a computer.
Front View
Lamp 1 indicator
Power indicator
69
69
72
Lamp 2 indicator
69
Temperature warning
69
indicator
Lamp unit cover
Speaker
55
55 Speaker
Adjustment foot
(on the bottom of
the projector)
30
Remote control sensor
16
66
77
Exhaust vent
Attaching the lens cap/dustproof cap
Snap on the lens cap/dustproof cap
straight.
Lens cover removal button
Adjustment foot
(on the bottom of the projector)
30
77
Removing the lens cap/dustproof cap
Pull the lens cap/dustproof cap directly
outward.
Lens cover
-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Projector (Rear View)
Terminals Refer to “Connecting the Projector to Other Equipment” on pages 24–26.
HDMI terminal
COMPUTER/COMPONENT 2
terminals
BNC terminals for computer
RGB and component signals
and audio input terminal.
24
25
24
25
Terminal for HDMI input.
DVI-D input terminals
Terminals for DVI digital
RGB and digital component
signals and audio input
terminal.
24
25
27 LAN terminal
Terminal for controlling the
projector using a computer
via network.
COMPUTER/COMPONENT1
input terminals
Terminals for computer RGB
and component signals and
audio input terminal.
24
25
RS-232C terminal
Terminal for controlling the
projector using a computer.
27
17
WIRED REMOTE terminal
For connecting the remote control
to the projector when the signals
from the remote control cannot
reach the remote control sensor.
MONITOR OUT terminals 26
∫COMPUTER/COMPONENT
Output terminal for computer
RGB and component signals.
(Shared for COMPUTER/
COMPONENT 1 and 2 input.)
∫AUDIO Output terminal.
S-VIDEO input terminals
Terminals for connecting video
equipment with an S-video
26
28
(Shared for all inputs)
terminal and audio input terminal.
VIDEO input terminals
26
AC socket
Connect the supplied power cord.
Terminals for connecting
video equipment and audio
input terminal.
Filter cover
67
68
(Intake vent)
Carrying handle
Kensington Security
Standard connector
For carrying the projector.
Remote control sensor
16
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Remote Control
FOCUS buttons
31
28
ON button
28
For adjusting the focus.
For turning the power on.
17 ADJ./MOUSE switch
For switching the remote control
modes.
STANDBY button
For putting the projector into
standby mode.
30 H&V LENS SHIFT button
For shifting the lens horizontally
and vertically.
ZOOM buttons
For adjusting the projected image size.
31
32
MENU button
For displaying adjustment and
setting screens.
47
KEYSTONE button
For entering the Keystone
Correction mode.
•
18 47
R-CLICK/UNDO button
• For right-clicking while the
ADJ./MOUSE switch is in the
MOUSE position.
•
Mouse/adjustment button
('/"/\/|)
18 47
• For moving the computer cursor
while the ADJ./MOUSE switch is
in the MOUSE position.
• For undoing an operation or
returning to the previous
display while the ADJ./MOUSE
switch is in the ADJ. position.
• For selecting menu items while
the ADJ./MOUSE switch is in the
ADJ. position.
ENTER button
For setting items selected or
adjusted on the menu.
SHUTTER buttons
41
• OPEN: For opening the shutter.
• CLOSE: For closing the shutter and
hiding the projected Image.
L-CLICK button
For left-clicking while the ADJ./MOUSE
switch is in the MOUSE position.
36 Volume buttons
18
For adjusting the speaker sound level.
37 MUTE button
For temporarily turning off the
MAGNIFY (enlarge/reduce) buttons
For enlarging/reducing part of the image.
37
sound.
FREEZE button
38
39
For freezing images.
BREAK TIMER button
41
54
For setting the break time.
RESIZE button
For switching the screen size.
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
38
PICTURE MODE button
For switching the picture mode.
COMPUTER 1/2, DVI, HDMI,
VIDEO, S-VIDEO buttons
For switching to the respective
input modes.
36
17 WIRED R/C JACK
LIGHT button
For lighting all buttons on the
remote control.
For connecting the remote control
to the projector when the signals
from the remote control cannot
reach the remote control sensor.
Note
• The LIGHT button on the remote control is made of luminous material that is visible in the dark. Visibility
will diminish over time. Exposure to light will recharge the luminous buttons.
-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Front View
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the il-
lustration.
Remote control
signal transmitters
23' (7 m)
Note
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
Remote control
Rear View
Remote control sensor
When using the remote control:
• Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Remote control
signal transmitters
23' (7 m)
Remote control
Inserting the Batteries
1
Press the tab and lift open the battery
cover in the direction of the arrow
.
2 Insert the batteries.
• Insert the batteries making sure the po-
larities correctly match the and
marks inside the battery compartment.
3 Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with the alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the
and
marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the positioning of the projector, use a
ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector
with the remote control.
Rear view
Remote control
To WIRED R/C JACK
To WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available or
available as Sharp service part QCNWGA038WJPZ)
Note
• The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projec-
tor. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be discon-
nected from the projector.
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the other is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.
Projector control
Wireless computer mouse
ADJ.
ADJ.
MOUSE
MOUSE
Info
• When using the remote control as the wireless computer mouse, connect the optional remote receiver
(AN-MR2) to the computer. (See page 18.)
-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Using the Remote Control as a Wireless Computer Mouse
When connecting the optional remote re-
Computer
Remote receiver
ceiver (AN-MR2) to the computer, you can
use the remote control as the wireless com-
puter mouse.
1 Connect the optional remote re-
ceiver to the USB terminal on the
computer.
ADJ.
2 Slide the ADJ./MOUSE
switch on the remote con-
To USB terminal
MOUSE
trol to the MOUSE position.
3 Use the mouse function.
• Point the remote control at the remote
receiver.
■ When moving the cursor
Press '/"/\/|.
■ When left-clicking
ADJ./MOUSE switch
Press L-CLICK.
■ When right-clicking
Mouse/adjustment button ('/"/\/|)
Press R-CLICK.
■ When your computer supports only a
one-click mouse (such as Macintosh®)
Press L-CLICK or R-CLICK. (L-CLICK
and R-CLICK have common function.)
R-CLICK button
L-CLICK button
Note
• This function only works with the Microsoft®
Windows® OS and Mac OS®. However, this func-
tion does not work with the following operation
systems that do not support USB.
• Versions earlier than Windows® 95.
• Versions earlier than Windows® NT4.0.
• Versions earlier than Mac OS® 8.5.
• Confirm that the computer recognizes the USB
connection.
• While the remote control is connected to the
projector with a signal cable, you cannot use
the wireless computer mouse function.
-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
8
5
3
8
5
3
6
4
6
7
4 6
6
4
7
4 6
7
1.Place the projector facing a screen
Page 21
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than the computer,
see pages 25 and 26.
Pages 24, 28
3.Remove the lens cap and turn the projector on
Press ON on the projector or on the remote control.
Page 28
-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
4.Adjust the angle
Adjust the projector angle:
•
Shift the lens horizontally and vertically.
1
2
Press H&V LENS SHIFT on the projector or
on the remote control.
Press ', ", \ or | on the projector or the
remote control.
•
Adjust the projector angle by rotating the adjust-
ment feet.
Pages 29, 30
Page 31
5.Adjust the focus and the zoom
1 Press FOCUS +/– on the projector or on the remote control to adjust the focus.
2 Press ZOOM +/– on the projector or on the remote control to adjust the zoom.
6.
Correcting the image distortion due to the projection angle
1 Press KEYSTONE on the projector or on the remote control.
2 Press ENTER on the projector or on the remote control.
3 Press ', ", \ or | to move the position for the upper left of the image.
4 Press ENTER to set the position.
5
Repeat the same procedure with the positions for the upper right, lower right and lower left of the image.
•
When the position of the lower left is set, the correction is made and the display disappears.
Page 32
7.Select the input mode
Press INPUT on the projector or COMPUTER1 on the remote control to select the “COMPUTER1” mode.
On the
projector
On-screen display (RGB)
On the remote
control
INPUT list
• When you press INPUT on the projector, the INPUT list appears.
Press '/"to switch the INPUT mode and then press ENTER.
•
When using the remote control, press COMPUTER1/2, DVI, HDMI, VIDEO or S-VIDEO to switch the input mode.
Page 36
8.Turn the power off
Press STANDBY on the projector or on the remote control. While the confirmation message is displayed,
press STANDBY again.
" On-screen display
• You can unplug the power cord even if the projector is operating.
• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
Page 28
-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size. (For
details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.)
Top View
Side View
Screen
Lens center
Lower lens shift
position
(High mount setup)
Screen
H1
Leftmost lens shift
position
Lens center
Center of screen
W
Center of screen
Lens center
H2
Lens center
Upper lens shift
position
(Desktop setup)
L
Rightmost lens shift
position
Indication of the Projection Image Size and Projection Distance
For details, refer to “SETUP MANUAL” contained on the supplied CD-ROM.
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-P18EZ)
Picture Size
300"
240"
×
180"
200"
160"
×
120"
100"
80"
60"
80"
×
60"
48"
64"
×
48"
×
36"
Projection Distance
"–9'
"–12' –
7'2
(2.2 m – 2.7 m)
9'7
3.7 m)
4.6 m)
–15'
–
(2.9 m
–30' 9.1 m)
–
12'
(3.7 m
24'
–45'
(7.3 m
36'
(11.0 m – 13.7 m)
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Standard Zoom Lens (AN-P18EZ : Standard Equipment with XG-P610X)
F2.5, f=25.5-32 mm
4:3 Signal Input (Normal Mode)
Distance from the lens center to
the bottom of the image [H]
Distance from the lens
center to the center of
the image [W]
Picture (Screen) size
Projection distance [L]
χ
Diag. [ ]
Width
Height
Minimum [L1] Maximum [L2]
Lower [H1]
Upper [H2]
22.9 cm (9")
300'' (762 cm) 610 cm (240'') 457 cm (180'') 11.0 m (36' 0'') 13.7 m (45' 0'') –480.1 cm (–189
250'' (635 cm) 508 cm (200'') 381 cm (150'') 9.1 m (30' 0'') 11.4 m (37' 6'') –400.1 cm (–157 1
200'' (508 cm) 406 cm (160'') 305 cm (120'') 7.3 m (24' 0'') 9.1 m (30' 0'') –320.0 cm (–126'')
150'' (381 cm) 305 cm (120'') 229 cm (90'')
5.5 m (18' 0'') 6.9 m (22' 6'') –240.0 cm (–94 1
"
)
±213.4 cm (84'')
±177.8 cm (70'')
±142.2 cm (56'')
±106.7 cm (42'')
±85.3 cm (33 19/32")
±71.1 cm (28'')
±56.9 cm (22 13/32")
±49.8 cm (19 19/32")
±42.7 cm (16 51/64")
/
2
"
)
19.1 cm (7 1/2")
15.2 cm (6'')
/
2
"
)
11.4 cm (4 1/2")
9.1 cm (3 19/32")
7.6 cm (3'')
120'' (305 cm) 244 cm (96'')
100'' (254 cm) 203 cm (80'')
80'' (203 cm) 163 cm (64'')
70'' (178 cm) 142 cm (56'')
60'' (152 cm) 122 cm (48'')
183 cm (72'')
152 cm (60'')
122 cm (48'')
107 cm (42'')
91 cm (36'')
4.4 m (14' 5'') 5.5 m (18' 0'') –192.0 cm (–75 19/32")
3.7 m (12' 0'') 4.6 m (15' 0'') –160.0 cm (–63'')
2.9 m (9' 7'')
2.6 m (8' 5'')
2.2 m (7' 2'')
3.7 m (12' 0'') –128.0 cm (–50 13/32")
3.2 m (10' 6'') –112.0 cm (–44 3/32")
6.1 cm (2 13/32")
5.3 cm (2 3/32")
4.6 cm (1 51/64")
2.7 m (9' 0'')
–96.0 cm (–37 51/64"
)
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H1: Lower distance from the lens center to the bottom of the image (cm/in)
H2: Upper distance from the lens center to the bottom of the image (cm/in)
W: Distance from the lens center to the center of the image (cm/in)
[m/cm]
χ
χ
L1 (m) = 0.03658
L2 (m) = 0.04572
χ
H1 (cm) = –1.6002
χ
H2 (cm) = 0.0762
χ
W (cm) = 0.7112
[Feet/inches]
χ
χ
L1 (ft) = 0.03658 / 0.3048
L2 (ft) = 0.04572 / 0.3048
χ
H1 (in) = –1.6002 / 2.54
χ
H2 (in) = 0.0762 / 2.54
χ
W (in) = 0.7112 / 2.54
16:9 Signal Input (Stretch Mode)
Distance from the lens center to
the bottom of the image [H]
Distance from the lens
center to the center of
the image [W]
Picture (Screen) size
Projection distance [L]
χ
Diag. [ ]
Width
Height
Minimum [L1] Maximum [L2]
Lower [H1]
Upper [H2]
250'' (635 cm) 553 cm (218'') 311 cm (123'') 10.0 m (32' 8") 12.5 m (40' 10") –384.0 cm (–151 11/64") 72.6 cm (28 19/32")
±193.7 cm (76 17/64")
±155.0 cm (61 1/64")
±116.2 cm (45 3/4")
±93.0 cm (36 39/64")
±77.5 cm (30 1/2")
±62.0 cm (24 13/32")
±46.5 cm (18 19/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'')
150'' (381 cm) 332 cm (131'') 187 cm (74'')
120'' (305 cm) 266 cm (105'') 149 cm (59'')
8.0 m (26' 2") 10.0 m (32' 8") –307.2 cm (–120 15/16") 58.1 cm (22 7/8")
6.0 m (19' 7") 7.5 m (24' 6") –230.4 cm (–90 45/64") 43.6 cm (17 5/32")
4.8 m (15' 8") 6.0 m (19' 7") –184.3 cm (–72 9/16") 34.9 cm (13 47/64")
4.0 m (13' 1") 5.0 m (16' 4") –153.6 cm (–60 15/32") 29.1 cm (11 7/16")
100'' (254 cm) 221 cm (87'')
80'' (203 cm) 177 cm (70'')
60'' (152 cm) 133 cm (52'')
125 cm (49'')
100 cm (39'')
75 cm (29'')
3.2 m (10' 6") 4.0 m (13' 1") –122.9 cm (–48 3
/
8")
23.2 cm (9 5/32")
2.4 m (7' 10") 3.0 m (9' 10")
–92.1 cm (–36 9/32") 17.4 cm (6 55/64")
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H1: Lower distance from the lens center to the bottom of the image (cm/in)
H2: Upper distance from the lens center to the bottom of the image (cm/in)
W: Distance from the lens center to the center of the image (cm/in)
[m/cm]
χ
χ
L1 (m) = 0.03985
L2 (m) = 0.04981
χ
H1 (cm) = –1.53583
χ
H2 (cm) = 0.29056
χ
W (cm) = 0.77483
[Feet/inches]
χ
χ
L1 (ft) = 0.03985 / 0.3048
L2 (ft) = 0.04981 / 0.3048
χ
H1 (in) = –1.53583 / 2.54
χ
H2 (in) = 0.29056 / 2.54
χ
W (in) = 0.77483 / 2.54
Note
• Allow a margin of error in the value in the diagrams above.
• When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
• See page 21 about projection distance [L] and distance from the lens center to the bottom of the image [H].
-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting a Reversed Image
Projection from behind the Screen
■ Place a translucent screen between the projector and the audience.
■ Reverse the image by selecting “Rear” in the “PRJ Mode” menu. (See page 62.)
Translucent screen
Audience
Projection Using a Mirror
■ Place a mirror (normal flat type) in front of the lens.
■ When the translucent screen is placed between the mirror and audience, select “Front” in the “PRJ Mode”
menu. (See page 62.)
■ When the mirror is placed on the audience side, select “Rear” in the “PRJ Mode” menu. (See page 62.)
Set to “Front”
Set to “Rear”
Mirror
Translucent screen
Audience
Audience
Mirror
Info
• When using a mirror, ensure that both the projector and the mirror are carefully placed so the projected
light does not shine into the eyes of the audience.
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount
adaptor and unit for this installation.
Before mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the recom-
mended ceiling-mount adaptor and unit (sold separately).
■ Invert the image by selecting “Ceiling + Front” in “PRJ Mode”.
See page 62 for use of this function.
-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off
the equipment to be connected. After making all connections, turn on the projector and then the other
pieces of equipment.When connecting a computer, ensure that it is the last equipment to be turned on after
all the connections are made.
IMPORTANT: Ensure that the appropriate input mode has been selected on the projector before you
turn on the connected equipment.
• For more details of connection and cables, refer to the operation manual of the connected equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Equipment
Computer
Terminal on connected equipment
Cable
Terminal on the projector
COMPUTER/COMPONENT1
RGB output terminal
RGB cable (supplied)
Computer audio output
terminal
Computer audio cable (
commercially available)
ø3.5 mm stereo minijack,
Mini D-sub 15 pin/5 BNC cable (commercially available) COMPUTER/COMPONENT2
RGB output terminal
Computer audio cable (
commercially available)
ø3.5 mm stereo minijack,
Computer audio output
terminal
DVI digital output terminal DVI Digital cable (commercially available)
DVI-D
HDMI
Computer audio cable (
commercially available)
ø3.5 mm stereo minijack,
Computer audio output
terminal
HDMI digital output terminal
HDMI cable (commercially available)
Note
• When connecting the projector to a compatible computer other than a PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more
information.
• With the DVI digital connection, select “D. PC RGB” for “Signal Type” in the “Picture” menu.
• See page 75 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
•Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer). Refer to the specific instructions in your computer's operation manual to
enable your computer’s external output port.
-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Equipment
Terminal on connected equipment
HDMI digital output terminal
Cable
Terminal on the projector
HDMI
HDMI cable (commercially available)
Video equipment,
Camera, Video game
DVI-D
DVI Digital cable (commercially available)
DVI digital output terminal
Audio output terminal ø3.5 mm stereo minijack to RCA audio cable (commercially
available)
5 BNC cable (commercially available)
RGB video output terminal
COMPUTER/COMPONENT2
Audio output terminal ø3.5 mm stereo minijack to RCA audio cable (commercially
available)
Component video
output terminal
Component cable (commercially available) + BNC- COMPUTER/COMPONENT2
RCA adaptor plug (commercially available)
Audio output terminal ø3.5 mm stereo minijack to RCA audio cable (commercially
available)
COMPUTER/COMPONENT1
D-video
output terminal
Cables for a camera or a video game/3 RCA to
mini D-sub 15 pin cable (optional, AN-C3CP2)
RCA adaptor plug
(commercially available)
ø3.5 mm stereo minijack to RCA audio cable (commercially
available)
Audio output terminal
Note
• Select the input signal type of the video equipment when connecting to the COMPUTER1/2, DVI-D or
HDMI terminal. See page 51.
• The HD/C sync and VD terminals may be used depending on the specifications of the DTV decoder
connected to this projector. Please refer to the operation manual of the DTV decoder for details.
• The HD/C sync terminal of the 5 BNC terminal is only for TTL signal.
• Select “480P” or “576P” for “Resolution” on the “Fine Sync” menu, if necessary. (See page 53.)
• While the projector is connected to video equipment that has an HDMI output terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment that
has HDMI digital output terminal using HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by the
video equipment manufacturer.
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment
Equipment
Video equipment,
Camera, Video game
Terminal on connected equipment
Cable
Terminal on the projector
S-VIDEO
S-video output terminal
S-video cable (commercially available)
Audio output terminal RCA audio cable (commercially available)
VIDEO
Video output terminal Video cable (commercially available)
Audio output terminal RCA audio cable (commercially available)
RGB input terminal
RGB cable (supplied or commercially available)
MONITOR OUT
MONITOR OUT
Monitor
Amplifier
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Audio output terminal
Note
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• Video signal for monitor output is analog RGB signal as well as component signal (COMPUTER1/2). DVI
and HDMI input video signals would not be output.
• When the audio from HDMI input is directed to the MONITOR OUT (AUDIO) terminal, output will be
generated as Linear PCM audio.
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital
video signal does not degrade when transmitted, and a high-quality image with a simple connection can
be enjoyed.
• The HDMI terminal does not support the CEC signal.
This projector is able to process the following signals when connected to HDMI
equipment:
• Video signal: For details, see “HDMI Support” in the list of “Computer Compatibility Chart” on page 75.
• Audio signal: Linear PCM audio
• Sampling frequency: 48kHz/44.1kHz/32kHz
-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to the RS-232C serial terminal on
the computer, or when the LAN terminal on the projector is connected to the LAN terminal on
the computer, the computer can be used to control the projector. Refer to the“SETUP MANUAL”
contained on the supplied CD-ROM for details.
When connecting to a computer using an RS-232C serial control cable
Computer
Rear view
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable
(cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• Refer to“SETUP MANUAL”contained on the supplied CD-ROM for the RS-232C specifications and
commands.
Info
• Do not connect the RS-232C cable to a terminal other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
When connecting to the LAN terminal using a LAN cable
LINK LED (green)
Illuminates when linked.
Hub or computer
TX/RX LED (yellow)
Illuminates when
transmitting/receiving data.
Rear view
* To ensure safety, do not
connect the LAN terminal
with any cables such as a
To LAN terminal
To LAN terminal
telephone line that may
cause excessive voltage.
LAN cable
(Category 5 type, commercially available)
Note
•
When connecting to a hub, use straight-through Category 5 (CAT.5) type cable (commercially available).
• When connecting to a computer, use cross-over Category 5 (CAT.5) type cable (commercially available).
-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Supplied
accessory
Power cord
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into the AC outlet.
Rear view
Turning the Projector On
To AC socket
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages 24–27.)
To AC outlet
Power cord
Remove the lens cap and press ON on the
projector or on the remote control.
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projec-
tor is ready to start operation.
• When System Lock is set, the keycode input
screen appears. Enter the right keycode to
start projection. See page 60 for details.
Info
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the AC outlet or the
breaker switch is turned off when the projector is on,
then the projector automatically turns on when the power
cord is plugged into the AC outlet or the breaker switch
is turned on. (See page 63.)
• English is the factory preset language. If you want to change
the on-screen display to another language, change the lan-
guage according to the procedure on page 65.
Note
• The lamp indicator illuminates or blinks, in-
dicating the status of the lamp.
STANDBY button
ON button
Green: The lamp is on.
Blinking green: The lamp is warming up.
Red:The lamp is shut down abnormally
or the lamp should be replaced.
•
When switching on the projector, a slight flick-
ering of the image may be experienced within
the first minute after the lamp has been illumi-
nated. This is normal operation as the lamp’s
control circuitry is stabilizing the lamp output
characteristics. This does not indicate malfunc-
tion.
ON button
STANDBY
button
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to illuminate.
Power indicator
Lens cap
Lamp indicators1, 2
Turning the Power Off (Put-
ting the Projector into Standby Mode)
▼On-screen display
Press STANDBY on the projector or on
the remote control, then press that but-
ton again while the confirmation mes-
sage is displayed, to put the projector
into standby mode.
Info
• You can unplug the power cord from the AC outlet even if
the cooling fan is still running.Even if you unplug the power
cord from the projector, the cooling fan continues to run
for a while.
-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Shifting the Lens
In addition to the zoom function and adjustment of projection angle using the adjust-
ment feet, you can adjust the position of the projection using the lens shift function.
This is a useful function in cases such as when the screen cannot be moved.
When moving upward or downward When moving in the left and right direction
ange
le r
Adjustab
ange
le r
Adjustab
Adjustable
range
Adjustable range
• The adjustable range is shown below.
Horizontal range: 35%
Vertical range: 55%
The adjustable range has limitations even within the range shown above.
Select the correct type of lens that match with the installed lens (see page 62).
• The image can be adjusted as shown on the diagram.
AN-P15EZ, AN-P18EZ, AN-P23EZ, AN-P30EZ, AN-P45EZ
AN-P8EX, AN-P12EX
Position of the image when the image is centered, both
vertically and horizontally, in lens shift
Position of the image when the image is centered, both
vertically and horizontally, in lens shift
W X 20%
W X 20%
H X 55%
H X 31%
H X 18%
H
H
H X 18%
H X 31%
H X 55%
W
W
W X 35%
W X 35%
W X 11%
W X 11%
H : Height of the image
W : Width of the image
H : Height of the image
W : Width of the image
-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
1 Press H&V LENS SHIFT on the
projector or on the remote control.
• Pressing ENTER on the projector or on
the remote control displays the test pat-
tern. Checking the test pattern is useful
for more accurate adjustment.
H&V LENS SHIFT
button
Mouse/adjustment
button
('/"/\/|)
ENTER button
▼On-screen display
UNDO button
H&V LENS SHIFT
button
Adjustment button
('/"/\/|)
ENTER button
UNDO button
2 Press ', ", \ or | on the pro-
jector or the remote control to
adjust the image position.
Note
• When UNDO is pressed, the lens shift reset
screen is displayed. Lens shift can be reset
to factory default with this screen.
Using the Adjustment Feet
• When the position of the projected image cannot be adjusted
with the lens shift function, use the adjustment feet to adjust
the projected angle.
• The height of the projector can be adjusted using the
adjustment feet when the screen is located higher than the
projector, the screen is inclined or when the installation site
is slightly inclined.
• Install the projector so that it is as perpendicular to the
screen as possible.
1 Rotate the adjustment feet to
adjust the projected angle.
• The projector is adjustable up to approxi-
mately 5 degrees.
Adjustment feet
Warning!
• Do not hold the lens and lens cover when
projector angle is adjusted.
• Use caution not to pinch your finger in the
space between the adjustment foot and the
projector when the projector angle is lowered.
Down
Up
Up
Down
-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Focus
Press FOCUS +/– on the projector
or on the remote control to adjust the
focus.
ZOOM buttons
FOCUS buttons
▼On-screen display
Info
• It is recommended that the focus be adjusted
after the projector has warmed up for at least 30
minutes.
FOCUS buttons
ZOOM
buttons
Adjusting the Projected Image Size
Note
• After you have pressed FOCUS or ZOOM
on the remote control or the projector, you
can display the test pattern by pressing
ENTER. The test pattern is useful for mak-
ing more accurate adjustments.
• For fine adjustments, when H&V LENS
SHIFT, FOCUS or ZOOM is pressed, the
projected image moves a small amount in
the desired direction for approximately one
second.Hold down the buttons to move the
projected image quickly.
Press ZOOM +/– on the projector or
on the remote control to adjust the
projected image size.
▼On-screen display
-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Correcting Trapezoidal Distortion
When the image is projected either from the top or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion is called Keystone Correction.
There are the two types of the Keystone Correction.
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner of the projected im-
age
2) “H&V KEYSTONE” for designating the correction of the horizontal and vertical axes
Selecting the Type of the
Correction
KEYSTONE
button
Mouse/adjustment
button ('/"/\/|)
Select the type of the keystone correction.
ENTER button
Press KEYSTONE on the projector or on
the remote control.
UNDO button
• “GEOMETRIC ADJUSTMENT” will be dis-
played.
• Each time KEYSTONE is pressed, the display
toggles as follows:
GEOMETRIC
ADJUSTMENT
→
H&V KEYSTONE
↑
↑
KEYSTONE
button
The display
disappears.
←
IMAGE RESIZING *
Adjustment
button ('/"/\/|)
GEOMETRIC
ADJUSTMENT
For correcting an image desig-
nating the corner of the pro-
jected image
ENTER button
H&V KEYSTONE
For correcting an image desig-
nating the horizontal or vertical
axes
UNDO button
IMAGE RESIZING For correcting the image dis-
tortion which cannot be cor-
rected with “H&V KEY-
STONE”.
*Only when “H&V KEY-
STONE” is set to the values
other than “0”, “IMAGE
RESIZING” can be adjusted.
(This function cannot be used
when correcting with “GEO-
METRIC ADJUSTMENT”.)
-32
Download from Www.Somanuals.com. All Manuals Search And Download.
GEOMETRIC ADJUSTMENT
▼On-screen display
1 Press KEYSTONE on the pro-
jector or on the remote control
repeatedly until “GEOMETRIC
ADJUSTMENT” is displayed.
2 Press the buttons below to ad-
just the position, size or focus
of the projected image.
• Match screen’s four sides to green
test pattern.
• Pressing ', ", \ or | on the projector
or H&V LENS SHIFT on the remote
control allows you to shift the lens.
• Pressing ZOOM +/– on the projector or
on the remote control allows you to ad-
just the projected image size.
Geometric Adjustment
Upper Left Upper Right Lower Right
• Pressing FOCUS +/– on the projector
or on the remote control allows you to
adjust the focus.
3 Press ENTER on the projector
or on the remote control.
4 Press ', ", \ or | to move the
position for the upper left of the
Lower Left
image.
• Move the upper left of the yellow frame
onto the upper left of the screen.
5 Press ENTER to set the posi-
tion.
6
Repeat the same procedure with the
positions for the upper right, lower
right and lower left of the image.
• At this time, pressing UNDO on the pro-
jector or on the remote control returns
to the previous screen.
• Before correcting the upper left of the
image, pressing UNDO returns to the re-
set confirmation screen.
• When the position of the lower left is
set, the correction is made and the
display disappears.
• If the message “Can not correct.” is dis-
played, step 2 may have been performed
incorrectly. In this case, go back to step
2 and try the procedure again.
-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
H&V KEYSTONE
▼On-screen display
1 Press KEYSTONE on the pro-
jector or on the remote control
repeatedly until “H&V KEY-
STONE” is displayed.
• When the correction has already been
made with “GEOMETRIC ADJUST-
MENT”, the confirmation message for
resetting the correction before “H&V
KEYSTONE” is displayed, and then re-
set.
Vertical Keystone Correction
(Adjustment with '/ "
2 Press ' or " to parallelize the
left and right sides of the pro-
jected image.
)
Horizontal Keystone Correction
3 Press \ or | to parallelize the
upper and lower sides of the
projected image.
(Adjustment with \/ |
)
▼On-screen display
4 Press KEYSTONE to display
“IMAGE RESIZING”.
• Only when “H&V KEYSTONE” is set
to the values other than “0”, “IMAGE
RESIZING”works.
-34
Download from Www.Somanuals.com. All Manuals Search And Download.
IMAGE RESIZING
(Adjustment with '/ "/ \/ |
5 Press ', ", \ or | to correct
)
the image distortion.
6 Press KEYSTONE to set the
position.
-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Switching the Input
Mode
'/" buttons
Select the appropriate input mode for the con-
nected equipment.
Press COMPUTER1/2, DVI, HDMI,
VIDEO or S-VIDEO on the remote
control to select the input mode.
COMPUTER1/2,
DVI, HDMI, VIDEO
and S-VIDEO buttons
■ When you select the input mode with
INPUT P/R on the projector or P/R on
the remote control:
Input mode menu
• When P/R is pressed, the Input list ap-
pears. While the Input list is displayed,
follow the procedure below to switch the
input mode.
– Press P/R to select the desired input
mode and then press ENTER.
• When “AUTO SEARCH” is selected,
input signal is automatically detected.
• If ENTER is not pressed, the projector
switches to the selected input mode in
a few seconds.
Note
• When no signal is received, “NO SIGNAL”
will be displayed.When non-supported sig-
nal is received, “NOT REG.” is displayed.
• The input mode is not displayed when “OSD
Display” of the “Options1” menu is set to
“Level A” or “Level B”. (See page 57.)
Adjusting the Volume
Press VOL +/– on the projector or on
the remote control to adjust the volume.
Volume
buttons
Note
• Pressing VOL– will lower the volume.
Pressing VOL+ will raise the volume.
• When “Pict in Pict” (see page 56) is set to
“On”, audio volume cannot be adjusted on
the projector.The audio volume buttons will
instead function as location shift button for
the smaller screen.
"On-screen display
-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning Off the Sound
Temporarily
Press MUTE on the remote control
to temporarily turn off the sound.
MUTE button
Note
• Pressing MUTE again will turn the sound back on.
"On-screen display
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected
images can be enlarged. This is helpful when
providing more detailed explanations.
MAGNIFY
(enlarge/reduce)
buttons
Mouse/adjustment
button ('/"/\/|)
1 Press MAGNIFY
on the re-
mote control.
• Enlarges the image.
UNDO button
• Pressing
or
enlarges or re-
duces the projected image.
RESIZE button
Note
×1 ×2 ×3 ×4 ×9 ×16 ×36 ×64
• You can change the location of the en-
larged image using ', ", \and |.
2 Press UNDOon the remote con-
trol to cancel the operation.
• The magnification then returns to ×1.
Note
In the following cases, the image will
return to the normal size (×1).
- When switching the input mode.
- When UNDO has been pressed.
- When the input signal is changed.
-
When the input signal resolution and
refresh rate (vertical frequency) change.
- When RESIZE has been pressed.
-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Freezing a Moving
Image
1 Press FREEZE on the remote
control.
FREEZE button
• The projected image is frozen.
2 Press FREEZE again to return
to the moving image from the
currently connected equipment.
Selecting the Picture
Mode
You can select the suitable picture mode for the
projected image, such as movie or video game.
UNDO button
Press PICTURE MODE on the re-
PICTURE MODE
button
mote control.
• When pressing PICTURE MODE, the picture
mode changes in order of
STANDARD
PRESENTATION
MOVIE
CUSTOM
Note
• Press UNDO to return to the “STANDARD”
mode while the selected picture mode is dis-
played.
• This function can also be accessed from the
OSD menu (see page 49).
-38
Download from Www.Somanuals.com. All Manuals Search And Download.
This function allows you to modify or customize the resize mode to enhance the input image. Depend-
ing on the input signal, you can choose a desired image.
Resize Mode
Mouse/adjustment button
('/"/\/|)
Press RESIZE on the remote control.
• Pressing RESIZE changes the display as shown
in the tables below.
• To return to the standard image, press UNDO
while “RESIZE” is displayed on the screen.
• This function can also be accessed from the OSD
menu (see page 56).
UNDO button
RESIZE button
COMPUTER
Main resolution
NORMAL
FULL
DOT BY DOT
BORDER
STRETCH
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1152 × 864)
SXGA+ (1400 × 1050)
SXGA (1280 × 1024)
1280 × 720
800 × 600
—
768 × 576
4:3 aspect ratio
1024 × 768
—
1152 × 864
1400 × 1050
1280 × 1024
1280 × 720
1360 × 768
1366 × 768
1280 × 768
1280 × 800
1024 × 576
—
968 × 768
1024 × 576
1024 × 578
1024 × 576
1024 × 614
1024 × 640
720 × 576
1360 × 768
—
—
1024 × 768
Other aspect ratios
1366 × 768
1280 × 768
960 × 576
1024 × 576
1280 × 800
922 × 576
For 4:3 screen
FULL
For 16:9 screen
Input signal
Computer
Image type
NORMAL
DOT BY DOT
BORDER
STRETCH
Resolution
lower than
XGA
*1
XGA
*2
*2
SXGA
*1
(1152 × 864)
4:3 aspect ratio
Resolution
higher than
SXGA
*1
SXGA
(1280 × 1024)
5:4 aspect ratio
16:9 aspect ratio
*1
1280 × 720
*2
*2
1360 × 768
1366 × 768
1280 × 768
*1
*1
*1
1280 × 800
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Digital Shift function can be used for these images.
*2 Same as NORMAL mode.
-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
VIDEO/DTV
Input signal
For 4:3 screen
AREA ZOOM
For 16:9 screen
STRETCH
Video/DTV
Image type
NORMAL
V-STRETCH
BORDER
SMART STRETCH
*1
*1
*1
4:3 aspect ratio
*1
*1
*1
*1
*1
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Squeeze
*1
Letter box
720P, 1035I,
1080I, 1080P
*1
16:9 aspect ratio
*2
*2
*2
16:9 aspect ratio
540P
*1
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Digital Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video
image, the image will look different from its original appearance. Keep this in mind while choosing an image
size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for commercial
purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright
holders. Please use caution.
-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Hiding the Projected
Image (Shutter function)
This function allows you to tempo-
rarily hide the projected image.
SHUTTER
button
1 Press SHUTTER CLOSE.
• The projected image is hidden.
2 Pressing SHUTTER OPEN will
turn the projected image back
on.
Note
In the following cases, hiding will be cancelled
automatically.
• When STANDBY on the projector or on the
remote control is pressed.
• When a caution or information message is
displayed.
• When the power is turned on.
Displaying and Setting
the Break Timer
Mouse/adjustment
button
('/"/\/|)
This function allows you to show the re-
maining time for break during meeting.
UNDO button
1 Press BREAK TIMER.
BREAK TIMER
button
2 While“
” is displayed,press ',
", \or |to set the break timer.
• You can set anywhere between 1 and
60 minutes (in 1 units).
▼On-screen display
• The break timer starts to count down as
soon as ', ", \ or |is pressed.
Note
• Pressing UNDO will cancel the break timer.
• Auto Power Off function will be temporarily dis-
abled during the break timer.
When no input signal is detected for more than
15 minutes, the projector will automatically enter
the standby mode if the break timer has elapsed.
• The break timer will be displayed on the
startup image. To change the screen dis-
played during the break timer, change the
setting of “Startup Image” (see page 58).
• When “Slave” is set for “Stack Setting”, the
break timer is not displayed. (See page 62.)
-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
COMPUTER1/2, DVI, HDMI
Main Menu
Sub Menu
Picture
Standard
Presentation
Movie
Picture Mode
Page 49
Page 49
Custom
Contrast
-30
-30
-30
-30
-30
-30
-30
-30
+30
+30
+30
+30
+30
+30
+30
+30
Bright
Color
Tint
*1
*1
*1
*1
Red
Green
Blue
*1
*2
Sharp
Page 49
*1
*3
4500K
CLR Temp
Page 50
10500K
Progressive
2D Progressive
3D Progressive
Film Mode
Page 50
Standard
Custom 1
Custom 2
Custom 3
sRGB
C.M.S. Adjustment
Page 52
*1 *4
*5
Off
DNR
Level 1
Level 2
Level 3
Page 50
Reset
Page 49
COMPUTER1/2
DVI
D.PC RGB
HDMI
D.Video Auto
Signal Type
Auto
RGB
Component
D.PC Comp.
D.Video RGB
D.Video Comp.
D.Video RGB
D.Video Comp.
D.PC. RGB
Page 51
*6
*6
Dynamic Range
Auto
Standard
Enhanced
D.PC. Comp.
Page 51
Color Space
Auto
ITU601
ITU709
Page 51
*1 “Color”, “Tint”, “Red”, “Green”, “Blue” and “CLR Temp” cannot be adjusted when “C. M. S. Adjustment” is set to
“sRGB”.
*2 “Sharp” can be adjusted only when 480
*3 “Progressive” can be adjusted only when 480
*4 “sRGB” can be selected under the conditions below.
• When “Signal Type” is set to “RGB”, “D. PC. RGB” or “D. Video RGB”.
• When “Signal Type” is set to “Auto” or “D. Video Auto” and the input signal is distinguished as “RGB”.
*5 “DNR” can be adjusted only when 480 , 480P, 576 or 576P signal is input.
*6 “Dynamic Range” and “Color Space” can be worked only when DVI or HDMI signal is input.
I
, 480P, 540P, 576
I, 576P, 720P, 1035I, 1080I or 1080P signal is input.
I
or 576 signal is input.
I
I
I
-42
Download from Www.Somanuals.com. All Manuals Search And Download.
“Picture” menu
VIDEO/S-VIDEO
Main Menu
Sub Menu
Picture
Standard
Presentation
Movie
Picture Mode
Page 49
Page 49
Custom
Contrast
-30
-30
-30
-30
-30
-30
-30
-30
+30
+30
+30
+30
+30
+30
+30
+30
Bright
Color
Tint
Red
Green
Blue
Sharp
Page 49
4500K
CLR Temp
Page 50
10500K
Progressive
2D Progressive
3D Progressive
Film Mode
Page 50
Standard
Custom 1
Custom 2
Custom 3
C.M.S. Adjustment
Page 52
Off
DNR
Level 1
Level 2
Level 3
Page 50
Reset
Page 49
-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
“C.M.S.” menu
Main Menu
Sub Menu
C.M.S.
Standard
Custom 1
Custom 2
Custom 3
sRGB
C.M.S. Adjustment
Page 52
Page 52
[R] Red
Target
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
Page 52
[M] Magenta
Lightness
-30
-30
-30
+30
+30
+30
Page 52
Chroma
Page 52
Hue
Page 52
Reset (This Color)
Page 52
Reset (All Colors)
Page 52
View Settings
Page 52
“Fine Sync” menu
COMPUTER1/2, DVI, HDMI
Sub Menu
Main Menu
*6
*7
Fine Sync
Clock
Phase
H-Pos
V-Pos
Reset
-150 +150
-30 +30
-150 +150
-60 +60
Page 53
Page 53
Save Setting
Page 53
Select Setting
Page 53
Resolution
Page 53
Signal Info
Page 54
Auto Sync
Off
Normal
High Speed
Page 54
Auto Sync Disp
Background
Adjusting Disp.
Page 54
*6 The “Fine Sync” menu is displayed only while the input mode is COMPUTER1/2, DVI or HDMI.
*7 “Clock”, “Phase”, “H-Pos”, “V-Pos”, “Reset”, “Save Setting”, “Select Setting” and “Resolution” can be adjusted only
while the input mode is COMPUTER1 or 2.
-44
Download from Www.Somanuals.com. All Manuals Search And Download.
“Audio” menu
Sub Menu
Main Menu
Audio
Balance
Treble
-30
+30
+30
+30
+30
Page 55
-30
-30
-30
Bass
Reset
Page 55
Audio Out
FAO
VAO
Page 55
Speaker
On
Off
Page 55
“Options 1” menu
Main Menu
Sub Menu
*8
Options 1
Pict in Pict
On
Off
Page 56
Page 56
*9
Resize
Normal
Full
Page 56
Dot By Dot
Area Zoom
V-Stretch
Border
Stretch
Smart Stretch
Digi. Shift
-96
+96
Page 57
Normal
Level A
Level B
OSD Display
Page 57
*10
Video System
Auto
PAL (50/60Hz)
SECAM
Page 57
NTSC4.43
NTSC3.58
PAL-M
PAL-N
*8
Image Capture
Save Image
Delete
Page 57
Background
Logo
Custom
Blue
Page 58
None
Logo
Startup Image
Custom
None
Page 58
Eco Mode
On
Off
Page 58
Auto Search
Page 58
Auto Power Off
Page 58
System Lock
Page 59
On
Off
On
Off
*8 Item when inputting RGB signal through COMPUTER1/2, DVI or HDMI.
*9 Selectable items in “Resize” mode may differ depending on the signal.
*10 Item when selecting VIDEO or S-VIDEO.
-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
“Options 2” menu
“Language” menu
Main Menu
Options 2
Sub Menu
Main Menu
Sub Menu
Old Password
New Password
Reconfirm
Password
Language
English
Deutsch
Español
Nederlands
Français
Italiano
Page 61
Page 61
Page 65
Both Lamps
Lamp 1 Only
Lamp 2 Only
Equal Use
Lamp Mode
Page 62
Svenska
Português
polski
Türkçe
Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
Lens Type
Page 62
Front
PRJ Mode
Ceiling + Front
Rear
Page 62
Ceiling + Rear
“Status” menu
Normal
Master
Slave
Stack Setting
Page 62
Main menu
Status
Pair Stack
Page 65
Page 63
Normal
Level A
Level B
Keylock Level
Page 63
COMPUTER1 [ON/OFF]
COMPUTER2 [ON/OFF]
DVI [ON/OFF]
Set Inputs
Page 63
HDMI [ON/OFF]
VIDEO [ON/OFF]
S-VIDEO [ON/OFF]
Normal
High
Fan Mode
Page 63
On
Off
Auto Restart
Page 63
9600 bps
RS-232C
38400 bps
115200 bps
Page 64
Enable
Disable
Monitor Out
Page 64
LAN/RS232C
Enable
Disable
Page 64
Network
DHCP Client [ON/OFF]
*11
Page 64
IP Address
Subnet Mask
Gateway
TCP/IP
Page 65
Service Mode
Page 65
All Reset
Page 65
*11 Adjustable only when “DHCP Client” is set to “OFF”
-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
MENU button
Adjustment
buttons ('/"/\/|)
ENTER button
MENU button
Mouse/adjustment
button ('/"/\/|)
UNDO button
ENTER button
UNDO button
Menu Selections
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu for
COMPUTER1 (RGB) mode
1 Press MENU.
• The “Picture” menu screen for the se-
lected input mode is displayed.
2 Press \or |to display the other
menu items.
Menu items
• Menu items are as shown below.
Menu item
Note
• The “Fine Sync” menu is not available
for VIDEO or S-VIDEO.
-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
There are two methods of adjustment de-
pending on the menu item. Use the appli-
cable method from Example 1 or 2 shown
below.
Example 1: Adjusting “Bright”
3 Press 'or "to select the item
you want to adjust.
• Pressing
displays the items on the
lower part of the “Picture” menu.
To adjust the projected
image while viewing it
Press ENTER.
• The selected single adjustment item
(e.g. “Bright”) appears instead of the
menu.
Single
adjustment
item
• When pressing ' or ", the following
item (“Color” after “Bright”) will be dis-
played.
Note
• Press UNDO to return to the previ-
ous screen.
4 Press \ or | to adjust the item
selected.
• The adjustment is stored.
5 Press MENU.
• The menu screen will disappear.
Example 2: Selecting “Signal Type”
3 Press 'or "to select the item
you want to set and then press
ENTER.
4 Press ' or " to select the de-
sired item and then press EN-
TER.
5 Press MENU.
• The menu screen will disappear.
-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
Menu operation
Page 47
| Page 1
| Page 2
1
1
2
2
3
4
5
6
7
8
6
7
8
1
Selecting the Picture Mode
2 Adjusting the Image
This function allows you to select the picture
mode in accordance with brightness of the room
or content of the image to be projected.
In all picture modes, items on the“Picture”menu
can be adjusted and saved.
Select a picture mode before adjusting the im-
age.
Selectable items
Contrast For less contrast
Bright
Color*1
Tint*1
Press
Press
\
|
For more contrast
For more brightness
For more color intensity
For making skin tones
greenish
For less brightness
For less color intensity
For making skin tones
purplish
Selectable items
Standard
Description
For standard image
Presentation
Brightens darker portions of image for
more enhanced presentations.
Gives greater depth to darker portions
of image for a more exciting theater
experience.
Red*1
Green*1
Blue*1
For weaker red
For stronger red
For weaker green
For weaker blue
For less sharpness
For stronger green
For stronger blue
For more sharpness
Movie
Sharp*2
Custom
The factory preset value is the same as
the one of “Standard”.
Using the dedicated software “Sharp
Gamma Manager” allows you to adjust
the gamma curve.
*1 “Color”, “Tint”, “Red”, “Green” and “Blue” cannot
be adjusted when “C.M.S. Adjustment” on the
“C.M.S.” menu is set to “sRGB”. (See page 52.)
*2 “Sharp” can be adjusted only when 480I, 480P,
540P, 576I, 576P, 720P, 1035I, 1080I or 1080P
DTV signal is input during the COMPUTER1/2,
DVI, HDMI mode; or the input mode is set to
VIDEO or S-VIDEO.
Visit “http://sharp-world.com/projector/”
for details.
Note
• You can also press PICTURE MODE on the re-
mote control to select the picture mode. (See
page 38.)
Note
• To reset all adjustment items, select “Reset” and
press ENTER.
-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
Menu operation
Page 47
3
Adjusting the Color Temperature
5
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Selectable items
Description
4500K For lower color temperature for warmer,
reddish incandescent-like images.
Selectable items
Off
Level 1–3
Description
DNR does not function.
Sets the DNR level.
For higher color temperature for cooler,
10500K bluish, fluorescent-like images.
Note
Note
• “CLR Temp” cannot be set when “C.M.S. Ad-
justment” on the “C.M.S.” menu is set to “sRGB”.
(See page 52.)
• Set a level so as to view a clearer picture.
Make sure to set “DNR” to “Off” in the
following cases:
• When the image is blurry.
• When the contours and colors of moving im-
ages drag.
• WhenTV broadcasts with weak signals are pro-
jected.
4
Selecting the Progressive Mode
Selectable items
Description
2D
Useful to display fast-moving images such
as sports and action films.
Useful to display relatively slowmoving
images such as drama and documentary
more clearly.
Reproduces the image of film source*
clearly. Displays the optimized image of film
transformed with three-two pull down (NTSC
and PAL60Hz) or two-two pull down
(PAL50Hz and SECAM) enhancement to
progressive mode images.
Info
Progressive
3D
Progressive
• This function is available for all signals with
VIDEO or S-VIDEO.
• This function is available for 480I, 480P, 576I
and 576P signals with COMPUTER1/2, DVI or
HDMI.
Film Mode
*
The film source is a digital video recording with the original
encoded as is at 24 frames/second. The projector can con-
vert this film source to progressive video at 60 frames/sec-
ond with NTSC and PAL60Hz or at 50 frames/second with
PAL50Hz and SECAM to play back a high-definition image.
Note
•
In NTSC or PAL60Hz, even if the 3D Progressive
mode has been set, the three-two pull down enhance-
ment will be enabled automatically when the film
source has been entered.
•
•
When the image is blurred or noisy, switch to the
optimal mode.
When using progressive inputs, inputs are directly
displayed so that “2D Progressive”, “3D Progressive”
and “Film Mode” cannot be selected.
-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Page 47
6
Selecting the Signal Type
7 Selecting the Dynamic
Range
When using an input mode other than S-VIDEO or
VIDEO input, set the signal type setting to the cor-
responding input signal type (RBG or Component).
An optimum picture may not be displayed if a DVI-D
or HDMI capable device’s output signal type and
the projector’s input signal type do not match. If this
should occur, switch the “Dynamic Range”mode.
■ When COMPUTER1/2 is selected for the input
mode
Selectable items
Auto
Description
In most circumstances, “Auto” should
be selected.
When the black levels of the image
show banding or appear faded, select
the item that results in the better picture
quality.
Selectable items
Auto
Description
Automatically selects the appropriate
input signal between RGB and Compo-
nent.
Set when RGB signals are received.
Set when component signals are
received.
Standard
RGB
Component
Enhanced
■ When DVI is selected for the input mode
Selectable items
D. PC RGB
Description
Set when digital PC RGB signals are
received from the computer.
8
Selecting the Color Space
This function select the color space for signals in-
put from a DVI-D- or HDMI-compatible device.
D. PC Comp. Set when digital PC component signals
are received from the computer.
D. Video RGB Set when digital video RGB signals are
received from video equipment.
D. Video Comp. Set when digital video component signals
are received from video equipment.
Selectable items
Auto
Description
In most circumstances, “Auto” should
be selected.
Select the item that results in the better
picture quality.
ITU601
ITU709
■ When HDMI is selected for the input mode
This function sets the type of picture signal input from
HDMI-compatible equipment.
Selectable items
Description
D. Video Auto Automatically set the RGB or compo-
nent signal when digital video signals
are received from video equipment.
D. Video RGB Set when digital video RGB signals are
received from video equipment.
D. Video Comp. Set when digital video component signals
are received from video equipment.
D. PC RGB
Set when digital PC RGB signals are
received from the computer.
D. PC Comp. Set when digital PC component signals
are received from the computer.
-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Management System (“C. M. S.” menu)
Menu operation
Page 47
1
3
Setting the Brightness of
the Target Color
2
3
4
5
This function allows you to set the brightness of
the selected target color.
Press \
For less brightness of the For more brightness of the
target color target color
Press |
6
7
4
Setting the Chromatic
Value of the Target Color
1 Selecting the Color
This function allows you to set the chromatic
value of the selected target color.
Reproduction Mode
Press \
For less chromatic value of For more chromatic value of
the target color the target color
Press |
This function allows you to select the color re-
production mode for the projected images.
Selectable items
Standard
Description
Standard settings
Custom 1 – 3
“Lightness”, “Chroma” and “Hue” can be
adjusted for each of the six colors.
A natural tint based on an original im-
age from the computer.
5
Setting the Hue of the
Target Color
sRGB
This function allows you to set the hue of the
selected target color.
Note
• sRGB is an international standard of color repro-
duction regulated by the IEC (International
Electrotechnical Commission). As the fixed color
area has been decided by the IEC, the images are
displayed in a natural tint based on an original im-
age, when “C.M.S. Adjustment” is set to “sRGB”.
• You cannot set “Color”, “Tint”, “Red”, “Green”,
“Blue”, “CLRTemp” on the “Picture”menu, when
“C.M.S. Adjustment” is set to “sRGB”.
Press \
For stronger red of the
target color
Press |
For stronger yellow of the
target color
6 Resetting User-defined
Color Settings
• For additional information about the sRGB func-
tion, visit “http://www.srgb.com/”.
This function allows you to reset the specific tar-
get color or all of the six colors.
Selectable items
Description
Info
Reset (This Color) “Lightness”, “Chroma” and “Hue” of
the color selected for “Target” are
reset.
Reset (All Colors) “Lightness”, “Chroma” and “Hue” of
all colors are reset.
• When “C.M.S. Adjustment” is set to “sRGB”, the
projected image may become dark, but this
does not indicate a malfunction.
2
Selecting the Target Color
7
Overview of All Color Settings
This function allows you to select the target color
for adjusting the display characteristics.
This function allows you to confirm the settings
of all the colors.
Red
Yellow
Green
Cyan
Blue
Magenta
-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“Fine Sync” menu)
Menu operation
Page 47
2
Saving Adjustment Settings
This projector allows you to store up to seven
adjustment settings for use with various com-
puters.
1
2
3
4
5
6
7
3 Accessing Adjustment
Settings
Adjustment settings stored in the projector can
be easily accessed.
Note
• If a memory has not been set, the resolution
and frequency setting will not be displayed.
• When selecting a stored adjustment setting with
“Select Setting”, you can set the projector in the
stored adjustments.
1 Adjusting the Computer
Image
Use the Fine Sync function in case of irregulari-
ties such as vertical stripes or flickering in por-
tions of the screen.
4 Setting the Resolution
Selectable items
Clock
Description
Adjusts vertical noise.
Ordinarily, the type of input signal is detected
and the correct resolution mode is automatically
selected. However, for some signals, the optimal
resolution mode in “Resolution” on the “Fine
Sync” menu may need to be selected to match
the computer display mode.
Phase
Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos
V-Pos
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
Note
Note
• If your computer displays patterns which repeat
every other line (horizontal stripes), flickering
may occur which makes the image hard to see.
• See “Checking the Input Signal” on page 54 for
information on the currently selected input sig-
nal.
• You can automatically adjust the computer im-
age by setting “Auto Sync” on the “Fine Sync”
menu to “Normal” or “High Speed”, or by press-
ing AUTO SYNC on the projector or on the re-
mote control. See page 54 for details.
• To reset all adjustment items, select “Reset” and
press ENTER.
-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“Fine Sync” menu)
Menu operation
Page 47
7
Setting the Auto Sync
Display Function
5
Checking the Input Signal
You can check the input signal information.
Used to set the display during Auto Sync.
Selectable items
Background
Description
The image set as a background image
is projected. See page 58.
The computer image being adjusted is
displayed.
6 Auto Sync Adjustment
Used to automatically adjust a computer image.
Adjusting Disp.
Selectable items
Off
Description
Auto Sync adjustment is not automati-
cally performed.
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
“Normal” takes more time than “High
Speed” for more accurate Auto Sync
adjustment.
Normal
High Speed
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the projector or on
the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 53.)
• When AUTO SYNC is pressed while “Auto
Sync” is “High Speed” or “Off”, Auto Sync will
be executed in “High Speed” mode. If the but-
ton is pressed again within one minute, Auto
Sync will be executed in “Normal” mode.
-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustment (“Audio” menu)
Menu operation
Page 47
Note
When the projector is connected to audio equipment:
•
It is recommended that “FAO” be selected on “Audio
Out”. Because the audio signal from the audio equip-
ment does not vary in strength with the volume level
of the projector, you can enjoy better sound.
1
• When “FAO” is selected on “Audio Out”, video and
audio may not synchronize.
- When connecting audio equipment that has a
function for adjusting audio delay time, adjust
the delay time for synchronizing video and au-
dio.
2
3
- When the audio equipment does not have such
a function and the unsynchronized video and au-
dio bothers you, select “VAO” on “Audio Out”.
Selecting “VAO” synchronizes video and audio
automatically.
• The HDMI audio will not output from the
MONITOR OUT AUDIO terminal when the pro-
jector is in the standby mode.
1 Adjusting the Audio
This function allows you to adjust the projector’s
audio.
Selectable items
Press \
Press |
Balance Increased audio from Increased audio from
the left speaker
Treble For weaker treble
the right speaker
For stronger treble
For stronger bass
Bass
For weaker bass
3 Setting the Speaker
Note
This function allows you to turn the audio out-
put of the internal speaker on or off when the
projector is connected to an external amplifier.
• To reset all adjustment items, select “Reset” and
press ENTER.
Selectable items
On
Description
The audio signal is output from the internal
speaker.
2
Setting the Audio Output Type
The audio signal is not output from the
internal speaker.
Off
This function determines whether the audio level
output from the AUDIO OUTPUT terminal is fixed
or variable by linking with VOLUME.
Note
Selectable items
FAO
(Fixed Audio strength with the volume level of the
Output)
VAO
(Variable
Description
Audio output that does not vary in
• The HDMI audio will not output from the
MONITOR OUT AUDIO terminal when the pro-
jector is in the standby mode.
source projector.
Audio output that varies in strength with
the volume level of the source projec-
Audio Output) tor.
Info
•
When “Audio Out” has been set to “VAO”, first
make sure to lower the volume of the projector
before turning the power on or off and when
switching the input.
-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options 1” Menu
COMPUTER1/2, DVI, HDMI
Menu operation
Page 47
Note
1
2
3
4
6
7
8
9
0
q
w
• You can press '/ "/ \/ |on the projector or
on the remote control to change the location of
the inset picture image.
(The inset picture frame will be displayed. To dis-
play the inset picture to the desired position, move
the frame and press ENTER on the projector or
on the remote control.)
• When “On” is selected, INPUT and VOL on the
projector will function as location shift button for
the inset picture.
• Inset picture can only be displayed in compos-
ite video or S-video signal of NTSC/PAL/
SECAM.
• The audio of the inset picture will come out of
the projector’s speakers.
• While the “Pict in Pict” function is working, the
“FREEZE” function only works for the inset
picture.
VIDEO, S-VIDEO
• The “Pict in Pict” function does not work when
the following signals are input to the main
picture.
−UXGA/SXGA+/SXGA/WXGA signal
−480I/480P/540P/576I/576P/720P/1035I/1080I/
1080P signal
2
3
4
5
7
8
9
0
q
w
−Interlaced RGB signal
−
−
All signals (when “Resize”is set to “Dot by Dot”)
No signal (or when the resolution or refresh rate
(vertical frequency) of the signal is changed)
2 Setting the Resize Mode
Depending on the input signal, you can select
the screen image.
When inputting HDMI/
DTV/video signal
When inputting RGB signal
Normal
Normal
Full
Area Zoom
V-Stretch
Border
Stretch
Smart Stretch
Dot By Dot
Border
Stretch
1 Displaying Dual Pictures
(Pict in Pict)
The Pict in Pict (picture in picture) function al-
lows you to display two pictures on the same
screen. You can display the image input from
VIDEO or S-VIDEO as an inset picture overlap-
ping the main picture input from COMPUTER1/2,
DVI or HDMI.
Note
• For details of the Resize mode, see pages 39
and 40.
• You can also press RESIZE on the remote con-
trol to change the Resize mode. (See page 39.)
-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Page 47
3
Shifting the Projected
Image Vertically (Digital
Shift)
5
Setting the Video System
The video input system mode is factory preset
to “Auto”; however, a clear picture from the con-
nected audio-visual equipment may not be re-
ceived, depending on the video signal difference.
In that case, switch the video signal.
For easier viewing, this function shifts the im-
age projected on the screen up or down elimi-
nating either the upper or lower black band found
in 16:9 and other wide aspect ratios.
Selectable items
PAL (50/60 Hz) When connected to PAL video equipment.
Description
SECAM
NTSC4.43
When connected to SECAM video equipment.
When reproducing NTSC signals in PAL
video equipment.
Press \
Shifts the projected image Shifts the projected image
down. up.
Press |
NTSC3.58
When connected to NTSC video equipment.
Note
Note
• This function will not work depending on the type
• The video signal can only be set in VIDEO or
S-VIDEO mode.
of resize mode. See pages 39 and 40 for details.
• When “Video System” is set to “Auto”, you may
not receive a clear picture due to signal differ-
ences. Should this occur, switch to the video
system of the source signal.
• While “Video System” is set to “Auto”, when
PAL-M or PAL-N signal is input, the image from
PAL signal will be displayed.
4
Setting On-screen Display
This function allows you to turn the on-screen
messages on or off.
Selectable items
Normal
Level A
Description
All on-screen displays are displayed.
INPUT/VOLUME/MUTE/FREEZE/AUTO
SYNC/MAGNIFY/ “An invalid button has
been pressed.” are not displayed.
6
Capturing Projected Images
This projector allows you to capture projected
images (RGB signals) and set them as a startup
image, or background image when no signals are
being received.
Level B
All on-screen displays are not displayed (ex-
cept the menu, H&V LENS SHIFT, KEY-
STONE, FOCUS, ZOOM, “All buttons on Pro-
jector are locked.” and warning displays).
Note
Note
•
Images can be captured only when they are from
XGA (1024 × 768) non-interlace signals in COM-
PUTER1/2, DVI or HDMI mode with “RESIZE”
set to “Normal”.
• When “Keylock Level” is set to “Level A” or “Level
B”, pressing STANDBY displays “All buttons on
Projector are locked.” regardless of the “OSD
Display” setting.
• The saved image is reduced to 256 colors.
• Images from equipment connected to VIDEO
or S-VIDEO terminal cannot be captured.
• Only one image can be captured and saved.
• The color of images may differ before and after
saving if an image is captured on which image
adjustment has been performed using the
“C.M.S.” function.
• To delete the captured image, select “Delete”,
and then press ENTER.
-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options 1” Menu
Menu operation
Page 47
7
Selecting the Background
Image
0 Detecting the Input
Signals Automatically
Selectable items
Logo
Description
Selectable items
Description
Default image
On
Automatically searches for and switches to
the input mode in which signals are being
received.
Custom
Blue
User customized image (e.g. company logo)
Blue screen
None
Black screen
Off
“Auto Search” does not function.
Note
Note
• While the “Auto Search” function is detecting
the input signal, pressing a button on the pro-
jector or the remote control stops the “Auto
Search” function. After the “Auto Search” func-
tion finishes completely, press the desired button.
• When “Custom” is selected, an image saved us-
ing “Image Capture” can be displayed as a back-
ground image.
8
Selecting the Startup Image
q Setting the Auto Power
Selectable items
Description
Off Function
Logo
Default image
Custom
None
User customized image (e.g. company logo)
Black screen
Selectable items
On
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The “Auto Power Off” function will be
disabled.
Note
Off
• When “Custom” is selected, an image saved
using “Image Capture” can be displayed as a
startup image.
Note
• When “Auto Power Off” is set to “On”, 5 min-
utes before the projector enters the standby
mode, the message “Enter STANDBY mode in
X min.” will appear on the screen to indicate
the remaining minutes.
9 Setting the Eco Mode
When the two lamps are lit at the same time
Power consumption (When
Selectable items
Brightness
Lamp life
Approx.
using AC 100V)
Approx.
77%
On
Off
82%
3,000 hours*
Approx.
2,000 hours*
100%
100%
* This is a reference value and is not guaranteed.
Note
• When “Eco Mode” is set to “On”, the power con-
sumption will decrease and the lamp life will
extend.
-58
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
w Setting the System Lock
Function
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only autho-
rized users have access.
Note
• You cannot use the following buttons for
keycode:
ON, STANDBY, ENTER, L-CLICK, R-CLICK/
UNDO, MENU, ZOOM, FOCUS, H&V LENS
SHIFT
Info
• System Lock function recognizes each but-
ton on the remote control or on the projec-
tor as an individual button, even if they share
the same button name. If you set the keycode
with the buttons on the projector, use only
those buttons on the projector. If you set the
keycode with the buttons on the remote con-
trol, use only those buttons on the remote
control.
•
If you lose or forget your keycode, contact your near-
est Sharp Authorized Projector Dealer or Service
Center (see page 81). Even if the product warranty
is valid, the keycode reset will incur a charge.
Setting the keycode
1 Select “System Lock” on the “Op-
4 Enter the same keycode in“Recon-
firm”.
tions 1” menu, then press |.
• A message is displayed.
• Read this message, and press ENTER.
Note
2 Press the 4 buttons on the remote
control or on the projector to enter
Not displaying the keycode input screen
when turning the projector on
• Press "on the projector for four times in steps
3 and 4 above.
the preset keycode in “Old Code”.
• When setting the keycode for the first time,
press " on the projector for four times.
When the System Lock is set
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to start
projection. Failure to enter the keycode will
cause images not to be projected even when
signals are entered to the projector.
Note
• If you input a wrong keycode, the cursor returns
to the first point of the “Old Code”.
• The preset keycode is 4 "buttons on the projec-
tor.If this keycode is set, the keycode input screen
does not appear when turning the power on.
-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options 1” Menu
Changing the keycode
When the system lock is set
If you have set the system lock, enter the
keycode and follow the procedure below to
release the system lock.
▼Input screen for keycode
1 Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
Note
• When System Lock is set, the keycode input
screen appears after the power is turned on.
• If no keycode is entered, the image will not be
displayed, even if the projector receives the in-
put signal.
2
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
3 Enter the same keycode in“Recon-
firm”.
1 Press ON on the remote control or
on the projector to turn on the pro-
jector.
2 When the keycode input screen ap-
pears, enter the right keycode to
start projection.
Note
• System Lock function recognizes each but-
ton on the remote control or on the projector
as an individual button, even if they share
the same button name. If you set the keycode
with the buttons on the projector, use only
those buttons on the projector. If you set the
keycode with the buttons on the remote con-
trol, use only those buttons on the remote
control.
-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“Options 2” menu)
Menu operation
Page 47
Changing the password
1
2
3
4
5
6
1 Press ', "and |to enter the pass-
word in “Old Password” and press
ENTER.
7
8
9
0
2 Press ', " and | to set the new
password in “New Password” and
press ENTER.
q
w
e
r t
y
3 Enter the same 4-digit password in
“Reconfirm” and press ENTER.
u
Note
• If you do not want to set a password, leave the
fields blank in steps 2 and 3 and press ENTER.
• To cancel the password settings, press UNDO.
1 Setting a Password
• There is no factory preset for the password,
so the “Options 2” menu is enabled.
• If you do not want others to operate the
“Options 2” menu, set a password.
If You Forget Your Password
If you forget the password, delete it using the fol-
lowing procedure and set a new password.
1 Select “Password” from the
“Options 2” menu, and press |.
Press
on the
projector.
2 Press 'or "to set the first digit in
“New Password” and then press |.
3 Enter the remaining 3 digits and
press ENTER.
4 Enter the same password in
“Reconfirm” and press ENTER.
Info
• The password must be entered to use the
“Options 2” menu when a password has
been set.
-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“Options 2” menu)
Menu operation
Page 47
2 Setting the Lamp Mode
4 Reversing/Inverting
Projected Images
This function allows you to select the usage of
the two lamps installed in the projector.
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Selectable items
Both Lamps
Description
Both lamps are used for greater
brightness.
Selectable items
Front
Description
Normal image
Lamp 1 Only
Lamp 2 Only
Equal Use
The lamp 1 is used.
When the lamp 1 burns out, the lamp 2
automatically switches in use.
The lamp 2 is used.
When the lamp 2 burns out, the lamp 1
automatically switches in use.
Both lamps are used alternately for
certain periods.
Ceiling + Front Inverted image
Rear
Reversed image
Ceiling + Rear Reversed and inverted image
Note
• This function is used for the reversed image and
ceiling-mount setups. (See page 23.)
3 Selecting the Lens Type
When you change the lens, you need to set the
lens type. See the table below to select the lens
type.
5 Controlling Multiple
Projectors with the One
Remote Control
Selectable items
Type 1
Attached lens
AN-P8EX
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
AN-P12EX
AN-P15EZ
AN-P18EZ
AN-P23EZ
AN-P30EZ
AN-P45EZ
This function allows you to control multiple projectors
with the one remote control during the stack projec-
tion or the video wall projection. When using this func-
tion, connect the projectors with LAN cables and as-
sign a projector as the master and the other projectors
as the slaves. See page 27 for connecting LAN cables.
Info
Selectable items
Normal
Description
The stack setting is not available.
Set the projector as the master.
Set the projector as the slave.
•
The Lens Shift, Keystone Correction, etc. may not
properly function if the correct lens type is not se-
lected.
Master
Slave
Note
Note
•
When controlling multiple projectors with the one
• When “Lens Type” is changed, “GEOMETRIC
ADJUSTMENT”, “H&V KEYSTONE” and “IM-
AGE RESIZING” will be reset.
remote control, settings via web browser are re-
quired. Refer to the “SETUP MANUAL” contained
on the supplied CD-ROM for details.
•
•
Only when controlling two projectors with the one
remote control, using “Pair Stack” allows you to skip
settings via web browser. (See page 63.)
When “Slave” is selected on “Stack Setting”, the slave pro-
jector cannot be controlled with the remote control.
To control the slave projector with the remote control, con-
nect the remote control to the projector. (See page 17.)
-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Page 47
6 Shortcut to Make
8 Bypassing Unused Input
Projector Stack Settings
Selections
Normally, settings via web browser are required for
the stack projection. You can skip the settings via
web browser by using “Pair Stack”, only when you
use the two projectors for the stack projection.
This function allows you to skip the input mode
that you rarely use.You can skip the input modes
when “Auto Search” works
.
Selectable items
COMPUTER 1
COMPUTER 2
DVI, HDMI,
Description
Sets each input mode selectable
respectively.
Sets each input mode unavail-
able respectively.
ON
Note
• Before setting “Pair Stack”, select “Master” or
“Slave” on “Stack Setting”.
OFF
VIDEO, S-VIDEO
1 Select “Pair Stack” on the “Option
9 Selecting the Fan Mode
2” menu, and then press ENTER.
This function changes the fan rotation speed.
• The confirmation screen will be displayed.
Selectable items
Normal
High
Description
Suitable for normal environments.
Select this when using the projector at
attitudes of approximately 1,500 meters
(4,900 feet) or more.
2 Select “OK”, and then press
ENTER.
• The network settings of the projector will
change as shown below.
Note
Master
192.168.150.2
255.255.255.0
OFF
Slave
192.168.150.3
255.255.255.0
OFF
• When “Fan Mode” is set to “High”, the fan rota-
tion speeds up, and the fan noise becomes
louder.
IP Address
Subnet Mask
DHCP Client
Gateway
0.0.0.0
0.0.0.0
User Name
Password
(Reset)
(Reset)
(Reset)
(Reset)
Data Port
10002
10002
0 Setting the Auto Restart
Function
7 Locking the Operation
Selectable items
On
Description
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
The projector does not turn on automati-
cally when the power cord is plugged
into the AC outlet or the breaker switch
is turned on.
Buttons on the Projector
This function can be used to lock the use of cer-
tain operation buttons on the projector.
Selectable items
Normal
Description
Off
All operation buttons are functional.
Only INPUT/VOLUME buttons on the
projector are available.
Level A
Level B
All operation buttons on the projector
are unavailable.
-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“Options 2” menu)
Menu operation
Page 47
q
Selecting the Transmission
Speed (RS-232C)
e Setting the LAN/RS232C
When the LAN/RS232C has been set to“Enable”,
the LAN/RS232C is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the LAN/RS232C be set to“Disable”
when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
Make sure that both the projector and computer
are set for the same baud rate.
Selectable items
9600 bps
Description
Transmission speed is slow.
38400 bps
115200 bps
Transmission speed is rapid.
Selectable items
Enable
Description
The LAN/RS232C function is activated
even if the projector is in standby mode.
The LAN/RS232C function is switched off
when the projector is in standby mode.
Disable
Note
• Refer to the “SETUP MANUAL” contained on
the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.
• Refer to the computer’s operation manual for
instructions for setting the computer’s baud rate.
Note
• When you want to control the projector using
the LAN/RS232C function, select “Enable.”
• The item “LAN/RS232C” will be made unavail-
able for setting when “Master” or “Slave” is se-
lected on “Stack Setting”. (“LAN/RS232C” will
be set to “Enable”automatically.) (See page 62.)
w Setting the Monitor
Output
When the Monitor Out has been set to “Enable”,
the monitor output is activated and power is con-
sumed even in the standby mode. It is recom-
mended that the Monitor Out be set to “Disable”
when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
r Setting the DHCP Client
Connect the LAN cable before turning the pro-
jector on. If not, the DHCP Client function does
not work.
Selectable items
ON
Description
Obtains configuration parameters for
TCP/IP network automatically.
Sets the TCP/IP manually.
Selectable items
Enable
Description
The monitor output function is activated
even if the projector is in standby mode.
The monitor output function is switched off
when the projector is in standby mode.
OFF
Disable
Note
•
Select “ON” for “DHCP Client”. “Obtaining IP
Address...” appears, then the message “The
network settings have been changed.”, IP Address,
Subnet Mask and Gateway will be displayed.
• If the DHCP server is not available, “Could not
obtain IP Address.” appears.
In this case, set theTCP/IP manually.(See “Set-
ting the TCP/IP” on page 65.)
-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Functions Set during Installation (“Options 2”
menu)/Using the Other Menus (“Language” and
“Status” menus)
Menu operation
Page 47
t Setting the TCP/IP
y
Service Mode
Set the TCP/IP manually.
Only the service centers use the menu. Do not
use the menu.
1
Select “TCP/IP”, then press ENTER.
u Returning to the Default
2 Enter “IP Address” using ', ", |
Settings
and \, then press ENTER.
This function allows you to initialize the settings
you have made in the projector.
Note
About the network settings
• “IP Address”, “Subnet Mask”, “Gateway” and
other network setting items are initialized.
3 Enter “Subnet Mask” using ', ",
|and \, then press ENTER.
The following items or menu cannot be initialized.
• “C. M. S.” menu
4 Enter“Gateway”using ', ", |and
-“Lightness”, “Chroma” and “Hue” respectively
saved for Custom 1-3 on the “C.M.S.” menu.
• “Fine Sync” menu
\, then press ENTER.
-Resolution
• “Options 1” menu
-System Lock
• “Options 2” menu
Selectable items
IP Address
Description
Factory default setting:
192.168.150.002
Enter an IP address appropriate for the
network.
-Lens Type
• “Language” menu
• Image stored using “Image Capture”
• Lamp Timer (Life)
Subnet Mask
Gateway
Factory default setting:
255.255.255.000
Set the subnet mask to the same as that
of the computer and equipment on the
network.
Factory default setting:
000. 000. 000. 000
* When not in use, set to:
“000. 000. 000. 000”.
Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 16 languages.
Note
• Before setting “TCP/IP”, select “OFF” for “DHCP
Client”.
• Confirm the existing network’s segment (IP ad-
dress group) to avoid setting an IP address that
duplicates the IP addresses of other network
equipment or computers. If “192.168.150.002”
is not used in a network with an IP address of
“192.168.150.XXX”, you don’t have to change
the projector IP address.
Overview of All Menu
Settings and the Lamp Life
This function can be used to display all the ad-
justed settings as a list on the screen and you
can confirm the lamp life.
• For details about each setting, consult your net-
work administrator.
-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
Cleaning the air vents and the intake vent cover
■ Use a vacuum cleaner to clean dust from the ex-
haust vent, the intake vents and the intake vent cover
(on the bottom of the projector).
■ Ensure the power cord is unplugged before clean-
ing the projector.
■ The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on
the projector.
Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic may
cause damage to the quality or finish of the projector.
Info
• If you want to clean the air vents and the intake
vent cover during projector operation, ensure
you press STANDBY on the projector or on the
remote control and put the projector into standby
mode. After the cooling fan has stopped, un-
plug the power cord from the AC socket and
clean the air vents and the intake vent cover.
Mild detergent
diluted with water
Thinner
Wax
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
Cleaning the lens
■ Use a commercially available blower or lens clean-
ing paper (for glasses and camera lenses) for clean-
ing the lens. Do not use any liquid type cleaning
agents, as they may wear off the coating film on the
surface of the lens.
■ As the surface of the lens can easily get damaged,
be careful not to scrape or hit the lens.
Cleaning
aper
P
-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Replacing the Dust Filters
Cleaning the Dust Filters
STANDBY button
Info
• The dust filters should be cleaned every 100
hours of use. Clean the filters more often
when the projector is used in a dusty or
smoky location.
1 Press STANDBY on the projec-
tor or on the remote control to
put the projector into standby
mode.
• Disconnect the power cord and unplug
the power cord from the AC socket after
the cooling fan stops.
Power cord
2 Remove the filter cover.
• Remove the filter cover as shown in
the figures while pressing down the
tabs.
3 Clean the dust off the dust fil-
ters and the cover with a hand
broom.
-67
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Replacing the Dust Filters
4 Replace the filter cover.
• Insert the filter cover as shown in the
figure and push both the two tabs until
you hear a click.
1
2
Note
• Be sure the filter cover is securely installed.
The power will not turn on unless it is cor-
rectly installed.
Replacing the Dust Filters
Info
•
If the filters become too dirty to clean effec-
tively, purchase new ones (9NK3243101400)
from your nearest Sharp Authorized Projec-
tor Dealer or Service Center.
Remove
After removing the filter cover (see
step 2 of “Cleaning the Dust Filters”),
remove the dust filters, then replace
with new ones.
• Pick the dust filters up with your fingers and lift
them out of the filter cover.
• When attaching the dust filters, make sure that
these are inserted below the tabs on both left
and right, and that the slits are pierced through.
Attach
Pierced through
the nine slits.
Insert the filter
below the six tabs
on both left and
right sides.
-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
Maintenance Indicators
Power indicator
Lamp (1, 2) indicators
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will
turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and
then the projector will enter the standby mode. After “
” appears, ensure you perform the measures
described on page 70.
About the lamp indicator
“Change The Lamp. (LAMP 2)” is displayed when the remain-
ing life of the lamp 2 becomes 5% or less.
■When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp. (LAMP 1/
2)” will be displayed on the screen.
■When the percentage becomes 0%, it will change to “ ” (red), the lamp will automatically turn off. At
this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the lamp whose life is 0%
will not light up.
Indicators on the Projector
Power indicator Red on
Green on
Normal (Standby)
Normal (Power on)
Abnormal (See page 70.)
Red blinks
Green blinks Normal (Cooling)
Green on Normal
Green blinks The lamp is warming up.
Lamp (1, 2)
indicators
Red on
Off
The lamp is shut down abnormally or requires to be changed. (See page 70.)
Normal
Temperature
warning indicato
r
Red on
The internal temperature is abnormally high. (See page 70.)
-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
Maintenance indicator
Problem
Cause
Possible solution
Normal
Abnormal
• Relocate the projector to an area
with proper ventilation. (See page
10.)
• Blocked air intake
The internal
temperature is
abnormally high.
Temperature
warning
indicator
• Cooling fan break-
down
• Take the projector to your nearest
Sharp Authorized Projector Dealer
• Internal circuit failure or Service Center for repair. (See
Red on
(Standby)
Off
• Clogged air intake
• Clogged dust filter
page 81.)
• Clean the air vents and the dust
filter. (See page 67.)
• Disconnect the power cord from
the AC outlet, and then connect it
again.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
Red on
• Carefully replace the lamp. (See
page 72.)
• Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center for repair. (See
page 81.)
Green on
Green blinks
when the lamp
is warming up.
Lamp (1, 2)
indicators
Time to change
the lamp.
• Remaining lamp life
becomes 5% or less.
The lamp does
not illuminate.
Red on
(Standby)
• Burnt-out lamp
• Lamp circuit failure
• Please exercise care when
replacing the lamp.
• Securely install the filter cover or
lens cover.
The power
• The filter cover is
open.
• The lens cover is
open.
• If the power indicator blinks even
when the filter cover or lens cover
is securely installed, contact your
nearest Sharp Authorized Projector
Dealer or Service Center for
advice. (See page 81.)
Power
indicator
Green on/
Red on
Red
blinks
indicator blinks in
red when the
projector is on.
Info
• If the temperature warning indicator blinks and the projector enters the standby mode, the temperature
warning indicator starts to illuminate. Check whether any of the ventilation holes are blocked (see page 10)
and then try turning the power back on.Wait until the projector has cooled down completely before plugging
in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled
automatically. The sound of the cooling fan may change during operation because the fan speed may
change and this is not a malfunction.
-70
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp unit (sold separately) be replaced when the remaining lamp life
becomes 5% or less, or when you notice a significant deterioration in the picture and color quality.
The lamp life (percentage) can be checked with the on-screen display. See page 65.
■ Purchase a replacement lamp unit of type AN-P610LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
U.S.A. ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp indicator and on-screen display icon are illuminated, it is recommended that the
lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use.The lamp will be very hot and may cause burn
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. *If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not illuminate after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Removing and Installing
the Lamp Unit
Optional
accessory
Lamp unit
AN-P610LP
Warning!
• Do not remove the lamp unit from the pro-
jector right after use. The lamp and parts
around the lamp will be very hot and may
cause burn or injury.
Info
STANDBY button
• Make sure the lamp unit is removed using
the handle. Make sure the glass surface of
the lamp unit or the inside of the projector
are not touched.
• To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1 Press STANDBY on the projec-
tor or onthe remote control to put
the projector into standby mode.
• Disconnect the power cord and unplug
the power cord from the AC socket after
the cooling fan stops.
• The cooling fan may continue to run for
a while even after the power cord is re-
moved.
• Leave the lamp until it has fully cooled
down (about 1 hour).
Power cord
2
2 Remove the lamp unit cover.
• Loosen the user service screw (1) that
secures the lamp unit cover.Remove the
lamp unit cover to slide it in the direc-
tion of the arrow (2).
1
User service screw
-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing screws
3 Remove the lamp unit.
• Loosen the securing screws (two for
each lamp) from the lamp unit. Hold the
lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
Handle
4 Insert the new lamp unit.
• Fully insert the lamp unit into the lamp
unit compartment. Press the handles
back to their positions, and tighten the
securing screws.
5 Replace the lamp unit cover.
• Slide the lamp unit cover to the position
where the indicator “|” of the lamp cover
unit and the “\” of the projector will meet
to close the cover.Then tighten the user
service screw to secure the lamp unit
cover.
Compartment
for
Lamp 2
Compartment
for
Lamp 1
AN-P610LP
Info
• If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
User service screw
-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
ON button
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
2 Reset the lamp timer.
ENTER button
For Lamp 1
• When you reset the timer, while simul-
taneously holding down \, " and
ENTER, press ON on the projector.
• “LAMP 1 0000H” is displayed, indicat-
ing that the lamp timer is reset.
\,", | buttons
For Lamp 2
• When you reset the timer, while simul-
taneously holding down |, " and
ENTER, press ON on the projector.
• “LAMP 2 0000H” is displayed, indicat-
ing that the lamp timer is reset.
Power cord
-74
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
The table below lists signal codes that are compatible with the projector. When the images are distorted or
cannot be projected, adjust the output signal of your computer and so forth while referring to the table below.
Computer
• Multiple signal support
Horizontal Frequency: 15–126 kHz
Vertical Frequency: 43–200 Hz
Pixel Clock: 12–230 MHz
Sync signal: Compatible with TTL level
• Compatible with sync on green signal
The following is a list of modes that conform to VESA. However, this projector supports other signals
that are not VESA standards.
PC/
MAC/
WS
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
PC/
MAC/
WS
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
VESA
DVI
HDMI
VESA
DVI
HDMI
Resolution
Display
Resolution
Display
Standard Support Support
Standard Support Support
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
48.0
53.0
63.6
79.5
81.3
100.4
31.3
35.2
37.9
46.6
48.1
46.9
53.7
57.0
64.5
76.2
95.6
101.9
127.4
35.5
40.3
48.4
56.5
58.1
60.0
68.7
72.9
77.0
80.8
96.8
113.3
60
70
1280 720
45.0
47.8
49.7
62.8
47.7
47.8
55.0
66.2
64.9
67.5
76.6
77.1
90.2
54.5
65.9
67.4
64.0
60
60
60
75
60
60
60
70
72
75
80
85
100
60
72
74
60
640 350
1280 768
1280 800
1280 800
1360 768
1366 768
85
WXGA
60
720 350
640 400
70
60
70
85
60
1152 864
720 400
70
85
50
VGA
Advanced
Intelligent
60
Compression
70
SXGA
1152 882
1280 1024
72
PC
75
85
640 480
74.6
78.9
80.0
91.1
107.2
64.0
65.3
74.7
70
74
75
85
100
60
60
52
90
Upscale
100
120
150
160
200
50
SXGA+ 1400 1050
PC
56
60
75.0
81.3
60
65
70
70
UXGA 1600 1200 87.5
72
Intelligent
90.0
93.8
72
75
85
67
75
75
75
Compression
SVGA 800 600
85
106.3
90
MAC 13" VGA 640 480
MAC 16" SVGA 832 624
35.0
101
120
150
160
200
43
Upscale
True
49.7
60.2
MAC 19"
XGA 1024 768
MAC 21" SXGA 1152 870
68.7
75
72
HP (WS)
PC (WS)
WS
1280 1024 78.1
Advanced
Intelligent
Compression
60.0
1280 960
85.9
60
85
66
76
SXGA
50
61.8
1152 900
71.7
60
SUN (WS)
70
72
75
True
XGA 1024 768
85
90
95
100
120
140
-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
• When projecting the RGB interlace signal using COMPUTER 1/2 with “Signal Type” set to “Auto” or
“RGB”, the image may not be projected as desired. In this case, select either VIDEO or S-VIDEO.
• When “Screen resolution” of the computer is different from the resolution displayed on the projected
image, follow the procedures shown below.
–Refer to “Setting the Resolution” on page 53 and select the same resolution as the resolution in “Screen
resolution” of the computer.
–Depending on the computer you are using, the output signal may not be faithful to the “Screen resolu-
tion” adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed,
it is recommended that the resolution be set to the one that corresponds to “True” in the “Display”
column.
DTV
DVI/HDMI Support
(Compatible with HDCP)
Signal
480
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
I
15.7
31.5
33.8
15.6
31.3
45.0
37.5
33.8
33.8
28.1
67.5
56.3
60
60
60
50
50
60
50
60
60
50
60
50
480P
540P
576
I
576P
720P
1035
I
1080
I
1080P*
* When 1080P signal is input, the image is compressed before it is displayed on the screen.
-76
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Optional Lens
STANDBY button
H&V LENS SHIFT
Do not attempt to exchange the lens when the
projector is installed hanging from the ceiling.
Injury may occur if the lens cover and lens fall.
button
Before exchanging the lens, reset lens shift to the
center position. (The lens shift is located at the
center in the factory preset.)
UNDO button
When resetting the lens shift to the center position,
press H&V LENS SHIFT and then press UNDO.
• The lens shift reset screen will be displayed.
Select “Yes” to reset.
1 Press STANDBY on the projector
or on the remote control to put the
projector into standby mode.
• Disconnect the power cord and unplug the
power cord from the AC socket after the
cooling fan stops.
Power cord
2 Remove the lens cover.
• Press the lens cover removal button (1).
Slide the lens cover forward (2).
Removal lever
3 Turn the lens in the direction of the
arrow while pressing the lens re-
moval lever to pull the lens out.
-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Optional Lens
4 Remove the lens cap from a re-
placement lens.
Info
If you try to attach the lens to the projector
without removing this cap, the optional lens
attachment part can be damaged.
5 Insert the hook of the replacement
lens to the notch, and turn the lens
in the direction of the arrow.
• Make sure that the lens is locked with the
lens removal lever when you hear a click
sound.
6 Slide and attach the lens cover.
• The power cannot be turned on unless the
lens cover is fully inserted.
7 After changing (setting) the lens,
select the correct lens type. (See
page 62.)
-78
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
28
—
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
36
• Cables are incorrectly connected to the projector.
• Remote control batteries have run out.
24–27
16
•
•
External output has not been set when connecting notebook computer.
When the connected DVI digital equipment is turned on before the
“DVI” input mode is selected on the projector, the image may not be
projected properly or may not be displayed at all. Ensure that the
appropriate input mode has been selected and set the input signal type
on the projector before you turn on the connected equipment.
24
No picture and no sound
or projector does not start.
•
•
•
Is the lens cover correctly attached?
Is the filter cover correctly attached?
Is the lamp unit cover correctly attached?
78
68
73
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
• The “Shutter” is closed.
24–27
49
41
Sound is heard but no
picture appears.
• Image adjustments are incorrectly set.
49
(COMPUTER 1/2, DVI, HDMI only)
• Input signal type (RGB/Component) is incorrectly set.
(VIDEO, S-VIDEO only)
51
57
• Video Input system is incorrectly set.
Color is faded or poor.
• Adjust the focus.
31
22
• The projection distance exceeds the focus range.
• When an optional lens is attached, refer to the operation
manual of the lens.
•
There is fog on the lens. If the projector is carried from a cold
room into a warm room, or if it is suddenly heated, condensation
may form on the surface of the lens and the image will become
blurred. Please set up the projector at least one hour before it is
to be used. If condensation should form, remove the power cord
from the wall outlet and wait for it to clear.
—
(Computer Input only)
Picture is blurred;
noise appears.
53
53
76
—
• Perform “Fine Sync” Adjustments. (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments. (“Phase” Adjustment)
• Turn off the LCD display of the notebook computer.
• Noise may appear depending on the computer.
• The “DNR” (Digital Noise Reduction) setting is not correct.
• Cables are incorrectly connected to the projector.
• Volume is set to minimum.
50
24–27
36
• The “MUTE” function is working.
37
• The “Speaker” menu is set to “Off”.
55
Picture appears but no
sound is heard.
-79
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
—
An unusual sound is
occasionally heard
from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
Maintenance
indicator illuminates or
blinks in red.
• See “Maintenance Indicators”.
69
63
The projector cannot be • If the “Keylock Level” menu is set to “Level A” or “Level B”, all or
turned on or put into the
standby mode using the
ON or STANDBY button
on the projector.
specific buttons on the projector are unavailable. Use the
remote control to operate the projector.
All buttons on the
projector and the remote
control are unavailable.
• If the “Stack Setting” menu is set to “Slave” and the “Keylock
Level” menu is set to “Level B”, all buttons on the projector and
the remote control are unavailable. Connect the remote control
to the projector, and then use the remote control to operate the
projector.
17
62
63
Picture is green on
COMPUTER 1or 2
(COMPONENT).
• Change the input signal type setting.
51
Picture is pink (no green)
on COMPUTER 1/ 2 or
DVI (RGB).
The black levels of the • Make adjustments that result in the best picture quality in the
51
49
image show banding or
appear faded when DVI
or HDMI is selected.
“Dynamic Range” setting.
Picture is too bright and • Image adjustments are incorrectly set.
whitish.
The cooling fan
becomes noisy.
• When temperature inside the projector increases, the cooling
fan runs faster.
9, 10
66, 69, 70
The lamp does not light • The lamp indicator is illuminating in red.
69
up even after the
projector turns on.
Replace the lamp.
The lamp suddenly turns
off during projection.
The image sometimes • Cables are incorrectly connected to the projector or the
24–27
flickers.
connected equipment works improperly.
• If this happens frequently, replace the lamp.
The lamps take a long • The lamps will eventually need to be changed.
72
72
time to turn on.
The lamps have reached the end of its life. Replace the lamps.
Picture is dark.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s
remote control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it
will not be affected by strong light.
16
• Is a ø3.5 mm minijack cable plugged into the WIRED REMOTE
terminal?
• The batteries may be depleted or inserted incorrectly. Make
sure the batteries are inserted correctly or insert new ones.
16
This projector is equipped with a microprocessor. Its performance could be adversely affected by incorrect op-
eration or interference. If this should happen, unplug the projector and plug it in again after more than 5 minutes.
-80
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on pages 79 and 80. If this operation manual does not answer
your question, please contact the SHARP Service departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia
Pty. Ltd.
1300-135-022
Sharp Electronics Corporation Mexico
Branch
(525) 716-9000
New Zealand
Singapore
Hong Kong
Taiwan
Sharp Corporation of New Zealand
Phone:(09) 573-0111
Fax:(09) 573-0112
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Sharp Corporation (Taiwan)
0800-025111
France
Sharp Electronics France
01 49 90 35 40
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
-81
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
XG-P610X (Standard zoom lens attached) /
XG-P610X-N (No lens attached)
Display devices
Resolution
0.7" DLP® Chip ×3
XGA (1024 × 768)
F number
Zoom
Lens
F 2.5
(Standard)
Power, ×1.25 (f = 25.5 – 32.0 mm)
Focus
Power
Lens shift
Power (V : 55% / H : 35%)
HDMI
Input terminals
×1
×1
×1
×1
DVI-D (Compatible with HDCP)
Computer / Component (5BNC)
Computer/Component
(mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
×1
×1
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
×3
×2 (L/R)
×1
Computer/Component
(mini D-sub 15 pin)
Output terminals
Audio (ø3.5 mm stereo minijack)
LAN (RJ-45)
×1 (variable audio output)
Control and
communication
terminals
×1
×1
×1
RS-232C (mini DIN 9 pin)
Wired Remote
(ø3.5mm stereo minijack)
Speakers
3 W × 2 (Stereo)
Projection lamp
Rated voltage
Rated frequency
Input current
280 W × 2 lamps
AC 100 – 240 V
50/60 Hz
7.7 A
Power consumption (Standby)
755 W (16.7 W) with AC 100 V
710 W (16.9 W) with AC 240 V
41°F to 104°F (+5°C to +40°C)
Plastic
Operation temperature
Cabinet
19 22/32" × 25 3/32" × 7 31/64"
(500 × 637 × 190 mm)
XG-P610X: 57.4 lbs. (26.0 kg)
XG-P610X-N: 54.1 lbs. (24.5 kg)
Dimensions (main body only) [W × H × D]
Weight (approx.)
As a part of policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
-82
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
AC socket ....................................................................... 28
ADJ./MOUSE switch ...................................................... 17
Adjustment buttons ........................................................ 47
Adjustment feet .............................................................. 30
Advanced intelligent compression ................................ 75
All Reset ........................................................................ 65
Area zoom ..................................................................... 40
Aspect ratio .................................................................... 39
Audio .............................................................................. 55
Audio Out ....................................................................... 55
Auto Power Off............................................................... 58
Auto Restart................................................................... 63
Auto Search ................................................................... 58
Auto Sync (Auto Sync adjustment) ............................... 54
AUTO SYNC button ....................................................... 54
Auto Sync Disp .............................................................. 54
L-CLICK button .............................................................. 18
Lens cover ..................................................................... 77
MAGNIFY buttons.......................................................... 37
MENU button ................................................................. 47
Monitor Out .................................................................... 64
MONITOR OUT terminals ............................................. 26
Mouse button ................................................................. 18
MUTE button.................................................................. 37
Network.......................................................................... 64
Normal ........................................................................... 39
ON button ...................................................................... 28
Options 1 ....................................................................... 56
Options 2 ....................................................................... 61
OSD Display .................................................................. 57
Background.................................................................... 58
Border ............................................................................ 39
BREAK TIMER button ................................................... 41
Pair Stack....................................................................... 63
Password ....................................................................... 61
Phase ............................................................................. 53
Pict in Pict ...................................................................... 56
Picture............................................................................ 49
Picture Mode ................................................................. 49
PICTURE MODE button ................................................ 38
Power cord ..................................................................... 28
Power indicator .............................................................. 69
PRJ Mode ...................................................................... 62
Progressive .................................................................... 50
C.M.S. (Color Management System) ............................ 52
C.M.S. Adjustment ......................................................... 52
Carrying handle ............................................................. 14
Clock .............................................................................. 53
CLR Temp (Color Temperature) .................................... 50
COMPUTER1 button ..................................................... 36
COMPUTER2 button ..................................................... 36
COMPUTER/COMPONENT1 terminals ....................... 24
COMPUTER/COMPONENT2 terminals ....................... 24
R-CLICK button ............................................................. 18
Remote control .............................................................. 16
Remote control sensor .................................................. 16
Remote receiver ............................................................ 18
Resize ............................................................................ 39
RESIZE button ............................................................... 39
Resolution ...................................................................... 53
RGB cable ..................................................................... 24
RS-232C ........................................................................ 64
RS-232C terminal .......................................................... 27
DHCP Client .................................................................. 64
Digi. Shift........................................................................ 57
DNR ............................................................................... 50
Dot By Dot ..................................................................... 39
Dustproof cap ................................................................ 13
DVI button ...................................................................... 36
DVI-D terminals ............................................................. 24
Eco Mode....................................................................... 58
ENTER button................................................................ 47
Exhaust vent .................................................................. 66
S-VIDEO button ............................................................. 36
S-VIDEO terminals ........................................................ 26
Save Setting .................................................................. 53
Select Setting ................................................................ 53
Service Mode................................................................. 65
Set Inputs....................................................................... 63
SHUTTER buttons ......................................................... 41
Signal Info ...................................................................... 54
Signal Type .................................................................... 51
Smart Stretch ................................................................ 40
Speaker.......................................................................... 55
sRGB ............................................................................. 52
Stack Setting ................................................................. 62
STANDBY button ........................................................... 28
Startup Image ................................................................ 58
Status ............................................................................. 65
Stretch ........................................................................... 39
Subnet Mask .................................................................. 65
System Lock .................................................................. 59
Fan Mode ....................................................................... 63
Filter cover ..................................................................... 67
Fine Sync ....................................................................... 53
FOCUS buttons ............................................................. 31
FREEZE button ............................................................. 38
Gateway ......................................................................... 65
Geometric adjustment ................................................... 33
H-Pos ............................................................................. 53
H & V keystone .............................................................. 34
H & V LENS SHIFT button ............................................ 30
HDMI button................................................................... 36
HDMI terminal................................................................ 24
Image Capture ............................................................... 57
Image resizing ............................................................... 35
INPUT buttons ............................................................... 36
Intake vent ..................................................................... 66
IP Address ..................................................................... 65
TCP/IP ........................................................................... 65
Temperature warning indicator ...................................... 69
Kensington Security Standard connector ..................... 14
Keycode ......................................................................... 59
Keylock Level ................................................................. 63
KEYSTONE button ........................................................ 32
Keystone Correction ...................................................... 32
UNDO button ................................................................. 47
V-Pos .............................................................................. 53
V-stretch......................................................................... 40
VIDEO button................................................................. 36
VIDEO terminals ............................................................ 26
Video System ................................................................ 57
Volume buttons .............................................................. 36
Lamp .............................................................................. 71
Lamp indicators 1, 2 ...................................................... 69
Lamp Mode .................................................................... 62
Lamp Timer (Life) .......................................................... 65
Lamp unit cover ............................................................. 72
LAN terminal .................................................................. 27
LAN/RS232C ................................................................. 64
Language ....................................................................... 65
WIRED R/C JACK ......................................................... 17
WIRED REMOTE terminal ............................................ 17
ZOOM buttons ............................................................... 31
-83
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sennheiser Microphone e903 User Manual
Shure Headphones P4HW User Manual
Singer Sewing Machine 10uJ13 User Manual
Snapper Lawn Mower 12RTG Series User Manual
Soleus Air Air Conditioner KFH 18 User Manual
Sony eBook Reader PRS 950SC User Manual
Sony Flat Panel Television 50W700B User Manual
Star Micronics Network Card IP NPC User Manual
Tanita Scale BC 530 User Manual
Tanita Scale BF 572 User Manual