UXM-OBDE7L 00
FACSIMILE
OPERATION MANUAL
1. Installation
2. Sending Faxes
3. Receiving Faxes
4. Making Copies
5. Answering Machine Connection
6. Special Functions
7. Printing Lists
8. Maintenance
9. Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential installation.This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
ABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF 1991
"The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device to send any message via a telephone facsimile machine unless
such message clearly contains in a margin at the top or bottom of each transmitted page or on the
first page of the transmission the following information:
(1) The date and time of transmission.
(2) Identification of either the business, business entity or individual sending the message.
(3) Telephone number of either the sending machine, business, business entity or individual.
In order to program this information into your facsimile machine, please refer to the appropriate
instructions in the operation manual."
As an ENERGY STAR partner, SHARP has determined
that this product meets the ENERGY STAR guidelines
for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Welcome, and thank you for
choosing a SHARP inkjet
fax machine! The features
and specifications of your
inkjet fax are shown below..
Automatic dialing
Print cartridge
Rapid Key Dialing: 18 numbers
Speed Dialing: 81 numbers
Initial cartridge
Approx. yield 300 letter pages at 4% coverage*
Replacement cartridge: SHARP UX-C70B
Approx. yield 600 letter pages at 4% coverage*
Memory size**
1.8 MB (approx. 100 average pages)
Modem speed
14,400 bps with auto fallback to lower speeds.
Approx. 6 seconds (only when ECM is on)
Transmission time**
Scanning Resolution
Horizontal: 203 lines/inch (8 lines/mm)
Vertical:
Standard: 98 lines/inch (3.85 lines/mm)
Fine /Halftone: 196 lines/inch (7.7 lines/mm)
Super fine: 391 lines/inch (15.4 lines/mm)
Print resolution
600 × 600 dpi
Automatic document
feeder
Letter/A4: 20 pages max. (20-lb. paper)
Legal: 5 pages max.
Recording system
Thermal inkjet
64 levels
Halftone (grayscale)
Compression scheme
MR, MH, MMR
*When Ink Save mode is enabled.
**Based on Sharp Standard No. 1 Chart at standard resolution, excluding time for protocol
signals (i.e., ITU-T phase C time only).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper tray capacity
Letter: Approx. 200 sheets (20-lb. copier paper at
room temperature; maximum stack height should
not be higher than the line on the tray)
Legal: 100 sheets
Recommended paper weight: 20-lb. Copy Bond
Compatibility
ITU-T (CCITT) G3 mode
Input document size
Automatic feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length (20 pages): 5.5 to 11" (140 to 279 mm)
Length (5 pages): 5.5 to 14" (140 to 356 mm)
Manual feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 23.6" (140 to 600 mm)
Effective scanning width 8.3" (210 mm) max.
Effective printing width
Contrast control
8.0" (203 mm) max.
Automatic/Dark selectable
TEL/FAX/AM
Reception modes
Copy function
Single/Multi/Sort (99 copies/page)
Yes (cannot be used if power fails)
Telephone function
Applicable telephone line Public switched telephone network
Display
16-digit LCD display
120 V AC, 60 Hz
60 - 90°F (15 - 32°C)
25 - 80% RH
Power requirements
Operating temperature
Humidity
Power consumption
Standby: 5.0 W
Maximum: 30 W
Dimensions (without
attachments)
Width: 14.6" (372 mm)
Depth: 10.2" (259 mm)
Height: 8.0" (203 mm)
Weight (without
attachments)
Approx. 11 lbs. (5.0 kg)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
As a part of our policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
Important:
This fax machine is not designed for use on a line which has call waiting, call
forwarding, or certain other special services offered by your telephone company. If
you attempt to use the fax machine in conjunction with any of these services, you
may experience errors during transmission and reception of facsimile messages.
The fax machine is not compatible with digital telephone systems.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this
manual. Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do
not use the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Take care not to spill any liquids on the
machine.
Unplug the machine from the power outlet and telephone jack and consult a
qualified service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine
where people may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the
warranty.
Never insert objects of any kind into slots or openings on the machine. This could
create a risk of fire or electric shock. If an object falls into the machine that you
cannot remove, unplug the machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be
seriously damaged if it falls.
Never install telephone wiring during a lightning storm.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Never install telephone jacks in wet locations unless the jack is specifically designed
for wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily
accessible.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
A Look at the Operation Panel
7
9
1. Installation
Unpacking Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Loading Printing Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing the Print Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting the Telephone Line Cord. . . . . . . . . . . . . . . . . . . . . . . . 24
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . . 26
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2. Sending Faxes
33
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Adjusting the Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . 36
Sending a Fax by Normal Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Sending a Fax by Automatic Dialing. . . . . . . . . . . . . . . . . . . . . . . . . 40
Batch Page Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Sending a Fax From Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3. Receiving Faxes
57
Using FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Using TEL Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Optional Reception Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Substitute Reception to Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4. Making Copies
64
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5. Answering Machine Connection
66
Connecting an Answering Machine . . . . . . . . . . . . . . . . . . . . . . . . . 66
Using the Answering Machine Connection . . . . . . . . . . . . . . . . . . . . 67
Optional A.M. Mode Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6. Special Functions
72
Caller ID (Requires Subscription to Service) . . . . . . . . . . . . . . . . . . 72
Distinctive Ring (Requires Subscription to Service) . . . . . . . . . . . . . 77
Blocking Reception of Unwanted Faxes . . . . . . . . . . . . . . . . . . . . . . 79
Polling (Requesting a Fax Transmission) . . . . . . . . . . . . . . . . . . . . . 80
7. Printing Lists
85
8. Maintenance
90
Cleaning the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Improving Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
9. Troubleshooting
98
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Ordering Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
FCC Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Quick Reference Guide
Guía de referencia rápida
Index
114
115
116
6
Download from Www.Somanuals.com. All Manuals Search And Download.
A Look at the Operation Panel
3
4
2
1
PLAIN PAPER INKJET FAX
01
02
03
04
05
06
TEL FAX
07
13
08
14
09
15
10
11
12
AM
16/POLL
17/G1
18/G2
ABC
JKL
DEF
MNO
WXYZ
RESOLUTION
/
RECEPTION MODE
1
4
7
2
3
6
9
UP
GHI
FUNCTION
COPY/HELP
5
8
0
START/
SPEED DIAL
Z
MEMORY
A
PQRS
TUV
REDIAL
HOLD
DOWN
SPEAKER
STOP
PANEL RELEASE
6
7
8
10
13
11
12
5
9
Display
1
2
This displays messages and prompts to help you operate the machine.
FUNCTION key
Press this key followed by the arrow keys to select special functions and
settings.
RESOLUTION / RECEPTION MODE key
3
When a document is in the feeder, press this key to adjust the resolution for
faxing or copying. At any other time, press this key to select the reception
mode (an arrow in the display will point to the currently selected reception
mode).
Rapid Dial Keys
Press one of these keys to dial a fax number automatically.
4
5
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
SPEED DIAL key
6
Press this key to dial a fax or voice number using an abbreviated 2-digit
Speed Dial number.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER key
7
8
Press this key to listen to the line and fax tones through the speaker when
faxing a document.
Note: This is not a speakerphone. You must pick up the handset to talk with
the other party.
HOLD key
Press this key to put the other party on hold during a phone conversation.
When this is done, they cannot hear you. You can put the handset back in the
cradle without breaking the connection. When you are ready to speak with the
other party again, pick up the handset. If you did not put the handset back in
the cradle, press the HOLD key again to resume conversation.
PANEL RELEASE
9
Grasp here and pull up to open the operation panel.
COPY/HELP key
10
When a document is in the feeder, press this key to make a copy of a
document. At any other time, press this key to print out the Help List, a quick
reference guide to the operation of your fax machine.
STOP key
11
12
Press this key to cancel an operation before it is completed.
START/MEMORY key
Press this key after dialing to begin fax transmission. Press this key before
dialing to send a fax through memory. The key can also be pressed in the date
and time display to show the percentage of memory currently used.
Arrow keys
13
Use these keys to scroll through and select settings, and to search for auto-
dial numbers.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Installation
Unpacking Checklist
If any are missing,
contact your
dealer or retailer.
Before setting up,
make sure you
have all of the
following items.
Document
Print
Document tray
Paper tray
cover
Paper tray
exit support cartridge
Handset
Handset
cord
RapidKey
labels
Telephone
line cord
Operation
manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
Attachments
Points to keep in mind when setting up
Do not place the
machine near heaters
or air conditioners.
Keep dust away from
the machine.
Do not place the
machine in direct
sunlight.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper scanning of
documents for transmission. To remove the condensation, turn on the power and
wait approximately two hours before using the machine.
Removing the packing tape
1 Open the print compartment cover.
• Press as shown and pull the cover
toward you.
2 Remove the tape.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
3 Close the printer cover.
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset
cord goes into the jack
marked with a handset
symbol on the side of
the machine!
Use the handset to make ordinary phone calls,
or to transmit and receive faxes manually.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
Attaching the paper trays
Attach the paper tray.
Pull the paper plate
toward you and attach
the paper tray cover.
Paper plate
Attach the document
tray.
2
1
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
Pull out the received
document tray.
Attach the document exit support.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
Loading Printing Paper
You can load letter or legal size paper in the paper tray. Recommended paper
weight is 20-lb. Copy Bond. The maximum number of sheets is as follows:
Letter size: Approx. 200 sheets (20-Ib. copier paper at room temperature;
maximum stack height should not exceed line on tray)
Legal size: Approx. 100 sheets (20-Ib. copier paper at room temperature)
1 Pull the paper plate toward you, and
remove the paper tray cover from the
paper tray.
2 If you are going to load legal paper, flip
up the paper tray extension.
3 Pull the paper plate toward you and insert the stack of paper into the
tray, PRINT SIDE UP.
• If paper remains in the tray, take it out and combine it into a single stack
with the new paper.
The stack
should not
be higher
than this line
Be sure to load the paper so that
printing takes place on the print side
of the paper. Printing on the reverse
side may result in poor print quality.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
4 Pull the paper plate toward you and
replace the paper tray cover.
Place the
LETTER
LEGAL
cover using the
appropriate
notch for the
size of paper
loaded
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cord
Connecting the Power Cord
Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet.
Caution!
♦ Do not plug the power cord into any other kind of outlet. This will damage
the machine and is not covered under the warranty.
♦ Make sure you have removed all of the packing tape before plugging
in the power cord (see page 10). Plugging in the power cord without
doing so may damage the machine.
The machine does not have
a power on/off switch, so
the power is turned on and
off by simply plugging in or
unplugging the power cord.
“CHECK CARTRIDGE” normally
appears in the display the first
time you plug in the machine.
This message appears until you
install the print cartridge.
Note: If your area experiences a high incidence of lightning or power surges,
we recommend that you install surge protectors for the power and telephone
lines. Surge protectors can be purchased at most telephone specialty stores.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
Installing the Print Cartridge
When replacing the print
cartridge, use a SHARP
UX-C70B cartridge. One
cartridge can print about
600 letter-size pages.
The initial starter print
cartridge included with
your fax can print about
300 letter-size pages.
The above
yields are at 4%
coverage in INK
SAVE mode.
Caution!
Do not open the print compartment cover of the machine while it is
printing. If opened while printing, printing will stop.
Note: Keep ink cartridges sealed in their packages until you are ready to install
them. It is recommended that you do not use a cartridge that has been left unused
for a long time after opening, as the print quality may be considerably degraded.
♦ Make sure the power cord of the machine is plugged in and paper is loaded
before installing or replacing the print cartridge.
1 Open the operation panel.
If PRINTER ERROR or PRINTER ERROR/CHECK PAPER appears...
In the event that the display shows either of the above messages, you must clear the
error before installing the print cartridge. The error can usually be cleared by opening
and closing the print compartment cover (see Step 2), or if a paper jam has occurred, by
removing the paper jam (see page 107).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
2 Open the print compartment cover.
• Press as shown and pull the cover
toward you.
3 Remove only the tape from the the new
cartridge.
• Important: Make sure you remove all
of the tape.
• CAUTION! DO NOT touch the gold
contact area of the cartridge.
4 Make sure the cartridge holder is
between the “CARTRIDGE EXCHANGE
AREA” arrows on the label, and then
pull the green lever and open the
cartridge holder cover.
• If you are replacing the cartridge,
remove the old cartridge. If you are
going to use the old cartridge again,
place it in an air-tight container.
• CAUTION! DO NOT touch the contact
area inside the carriage carrier.
Note: If the print compartment cover is left
open for approximately 30 minutes with a
cartridge installed, the cartridge will
automatically return to its home position. To
make the cartridge return to the CARTRIDGE
EXCHANGE AREA when this has happened,
close the cover and then open it again.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
5 Insert the new print cartridge into the
cartridge holder.
6 Place your index finger on the tab as
shown and close the cartridge holder
cover with your thumb. Make sure the
cover clicks into place.
7 Close the print compartment cover.
8 Close the operation panel, pressing
down firmly on both front corners to
make sure it clicks into place.
Display:
CHANGE CARTRIDGE
1=NEW, 2=OLD
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
Display when “1” is selected:
9 Press
(NEW) if the cartridge you
installed is new.
Press (OLD) if the cartridge you
1
NEW CART.: OK?
2
installed is old.
OK: PRESS START
If you select the wrong number by mistake,
press
and repeat the selection.
STOP
START/
MEMORY
10 Press
.
If you selected “OLD” in the previous
step, this completes the installation
procedure. (Note: If you find that print
quality is not satisfactory after
reinstalling the old cartridge, align the
cartridge as explained on page 93.)
Display when “NEW” is
selected:
ALIGN CARTRIDGE
1=PRINT,2=SET
If you selected “NEW”, the display will
show the alternating messages at
right. Continue with the following steps
to align the print cartridge.
11 Press
to print an alignment page. (To enter an alignment value
1
without printing an alignment page, press .)
2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
12 In the alignment page that the machine prints, locate the line that comes
closest to forming a completely straight line.
After the alignment page is
printed, the display shows:
In this example, “15” comes
closest to forming a straight line.
ENTER (0-30) 15
13 Press the number keys to enter the number of the straightest line.
Example:
1
5
• If you make a mistake, press
and then repeat the entry.
STOP
START/
MEMORY
14 Press
.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
Note: If at any time the display shows the
ADD PAPER &
alternating messages at right, check the printing
paper. If the tray is empty, add paper. If there is
paper in the tray, take it out and then reinsert it.
PRESS START KEY
START/
MEMORY
When you are finished, press
.
Setting the paper size
The fax has been set at the factory to scale received faxes to letter size paper.
If you loaded legal paper, you must change the paper size setting to LEGAL.
Display:
FUNCTION
1 Press
once and
twice.
PRINT SET-UP
PAPER SIZE SET
2 Press
once and
once.
once.
1=LETTER,2=LEGAL
3 Press
The display briefly shows
your selection, then:
4 Select the paper size:
LETTER: LEGAL:
COPY CUT-OFF
1
2
5 Press
to return to the date and time display.
STOP
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Print Cartridge
Ink save mode
If you wish to use less ink or speed up ink drying time when printing faxes and
copies, turn on ink save mode. If you prefer a higher quality image, turn off ink
save mode.
♦ Ink save mode is initially turned off.
Display:
FUNCTION
PRINT SET-UP
1 Press
once and
twice.
INK SAVE MODE
2 Press
once and
once.
3 times.
1=YES, 2=NO
3 Press
The display briefly shows
your selection, then:
4 Press
to turn on ink save mode, or
1
ALIGN CART.
to turn it off.
2
5 Press
to return to the date and time display.
STOP
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Telephone Line Cord
Connecting the Telephone Line Cord
Insert one end of the line cord into the jack on the back of the machine
marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line
wall telephone jack.
L.SET
TEL.LINE
Setting the dial mode
The fax machine is set for tone dialing. If you are on a pulse dial line, you must
set the fax machine for pulse dialing. Press the panel keys as follows:
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
2 Press
once and
4 times.
DIAL MODE
3 Press
once.
1=TONE, 2=PULSE
The display briefly shows
your selection, then:
4 Select the dial mode:
TONE:
PULSE:
1
2
QUIET TIME
5 Press
to exit.
STOP
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Telephone Line Cord
Extension phone (optional)
If desired, you can connect an extension phone to the TEL. SET jack on the
fax machine.
♦ To connect an answering machine to the fax machine, see page 66.
1 Remove the seal covering the TEL. SET
jack.
TEL.SET
TEL.LINE
2 Connect the extension phone line to
the TEL. SET jack.
TEL.SET
TEL.LINE
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
Entering Your Name and Fax Number
Before you can begin sending
Once you enter this
faxes, you must enter your
information, it will
name and fax (telephone)
automatically appear at
number. You also need to set
the top of each fax page
the date and time.
you send.
Important!
FCC regulations require that your name, telephone/fax number, and the date and
time appear on each fax message you send. Enter your name and fax number
here and set the date and time as explained in the following section to have the fax
machine include this information automatically at the top of your fax messages.
FUNCTION
01
02
03
04
05
11
06
07
13
08
14
09
15
10
12
16/POLL
17/G1
18/G2
START/
1
4
7
2
5
8
0
3
6
9
MEMORY
STOP
Display:
FUNCTION
1 Press
once and
twice.
ENTRY MODE
OWN NUMBER SET
ENTER FAX #
2 Press
once.
once.
3 Press
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
4 Enter your fax number by pressing the number keys (max. 20 digits).
• To insert a space between digits, press
.
SPEAKER
• To clear a mistake, press
.
START/
MEMORY
5 Press
.
6 Enter your name by pressing number keys for each letter as shown in
the chart below. Up to 24 characters can be entered.
Example: SHARP = 7777 44 2 777
7
G =
H =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after
entering the first letter.
SPEAKER
♦ To clear a mistake, press
.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
repeatedly: . / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { |
} ) (
Display:
START/
MEMORY
7 Press
.
SECURITY
8 Press
to return to the date and time display.
STOP
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
Setting the Date and Time
The date and time appear in the
display and are printed at the top
of every page you fax. Set the
date and time as shown below.
FUNCTION
01
02
03
04
05
11
06
07
13
08
14
09
15
10
12
16/POLL
17/G1
18/G2
START/
1
4
7
2
5
8
0
3
6
9
MEMORY
STOP
FUNCTION
Display:
1 Press
once and
twice.
ENTRY MODE
DATE&TIME SET
2 Press
once and
3 times.
The currently set date
appears (example):
DATE 08-15-2003
3 Press
.
4 Enter a two-digit number for the month (“01” for January, “02” for
February, “12” for December, etc.).
Example: January
0
1
DATE 01-15-2003
• To correct a mistake, press
to move the cursor back to the mistake and
then enter the correct number.
5 Enter a two-digit number for the day (“01” to “31”).
th
Example: the 5
0
5
DATE 01-05-2003
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
The currently set time
appears (example):
6 Enter the year (four digits).
Example: 2003
2
0
0
3
TIME 12:19 PM
7 Enter a two-digit number for the hour (“01” to “12”) and a two-digit
number for the minute (“00” to “59”).
Example: 9:25
TIME 09:25 PM
0
9
2
5
8 Press
9 Press
to select A.M. or
to select P.M.
START/
ANTI JUNK #
MEMORY
to start the clock.
10 Press
to return to the date and time display.
STOP
Daylight Saving Time
If desired, you can set the clock to move forward and backward automatically
at the beginning and end of Daylight Saving Time. Follow these steps:
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
DAY LIGHT SAVE
1=YES, 2=NO
2 Press
once and
twice.
3 Press
once.
4 Press
to select YES, or
to select NO.
1
2
CLEAN ROLLER
5 Press
to return to the date and time display.
STOP
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Reception Mode
Setting the Reception Mode
Your fax has three modes for receiving incoming faxes:
FAX mode:
Select this mode when you only want to receive faxes on your line. The fax
machine will automatically answer all calls on four rings and receive incoming
faxes.
TEL mode:
Select this mode when you want to receive both phone calls and faxes on the
line connected to the fax machine. All calls, including faxes, must be
answered by picking up the fax machine's handset or an extension phone
connected to the same line.
A.M. mode:
Use this mode only if you have connected an answering machine to the fax
(see Chapter 5). Select this mode when you go out to receive voice messages
in your answering machine and faxes on your fax machine.
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then
RESOLUTION/
press
until the arrow in the display points to the desired mode.
RECEPTION MODE
RESOLUTION/
RECEPTION MODE
TEL FAX
JAN-03 10:30
01
02
03
04
05
11
06
A.M.
RESOLUTION/
RECEPTION MODE
07
13
08
14
09
15
10
12
TEL FAX
16/POLL
17/G1
18/G2
JAN-03 10:30
JAN-03 10:30
1
4
7
2
5
8
0
3
A.M.
6
9
TEL FAX
A.M.
For more information on receiving faxes in FAX and TEL modes, see Chapter 3,
Receiving Faxes. For more information on using A.M. mode, see Chapter 5.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment
Volume Adjustment
You can adjust the volume of the speaker, handset, and ringer using the up
and down arrow keys.
01
02
03
04
05
11
06
07
13
08
14
09
15
10
12
16/POLL
17/G1
18/G2
1
4
7
2
5
8
0
3
6
9
UP
SPEAKER
DOWN
Speaker
SPEAKER
1 Press
.
UP
Display:
2 Press
or
to select the
DOWN
SPEAKER: HIGH
desired volume level.
SPEAKER
• Press
speaker.
again to turn off the
SPEAKER: MIDDLE
SPEAKER: LOW
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment
Handset
1 When talking through the handset,
Display:
UP
press
or
to select the
RECEIVER: HIGH
DOWN
desired volume level.
• Note: The volume reverts to MIDDLE
RECEIVER: MIDDLE
RECEIVER: LOW
each time you replace the handset.
Ringer
UP
Display:
1 Press
or
to select the
has not been
DOWN
desired volume level.
RINGER: HIGH
SPEAKER
(Make sure
pressed, the handset is not lifted, and a
document is not loaded in the feeder.)
RINGER: MIDDLE
RINGER: LOW
• The ringer will ring once at the selected
level.
RINGER: OFF OK ?
2 If you selected RINGER: OFF OK ? to
START/
MEMORY
turn off the ringer, press
.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Sending Faxes
Transmittable Documents
Size and weight
Minimum document size:
Minimum size
Minimum weight
5.8"
(148 mm)
14 lbs.
(52 g/m² )
5.5"
(140 mm)
Maximum document size:
The maximum size and weight of documents that you can load in the
document feeder depend on how many pages you load.
20 pages at once:
1 page at a time (manual feeding):
Size: Letter
(8.5” x 11”, 216 x 279 mm)
Size: 8.5” x 23.6” (216 x 600 mm)
2
Weight: 42 lbs. (157 g/m )
2
Weight: 21.5 lbs. (80 g/m )
5 pages at once:
Size: Legal
(8.5” x 14”, 216 x 356 mm)
2
Weight: 21.5 lbs. (80 g/m )
0.16"(4 mm)
Letters or graphics on the
edges of a document will
not be scanned.
(The maximum scanning
width is 8.3” (210 mm), and
the top and bottom 0.16”
(4 mm) of the document
cannot be scanned.)
Letters in the
shaded area will
not be scanned.
8.3"(210 mm)
0.16"(4 mm)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Document
Other restrictions
♦ The scanner cannot recognize yellow, greenish yellow, or light blue ink.
♦ Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.
♦ All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.
♦ Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slick coated surface should be
photocopied, and the copy loaded in the feeder.
Loading the Document
Up to 20 letter-size pages, or 5 legal-size pages, can be placed in the feeder
at once. The pages will automatically feed into the machine starting from the
bottom page.
♦ If you need to send or copy more than the maximum number of pages,
place the additional pages gently and carefully in the feeder just before the
last page is scanned. Do not try to force them in, as this may cause double-
feeding or jamming.
♦ If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the feeder as the previous page
is being scanned. Insert gently to prevent double-feeding.
1 Adjust the document guides to the
width of your document.
2 Insert the document face down in the
document feeder. The top edge of the
document should enter the feeder first.
• READY TO SEND will appear in the
display.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Document
3 Adjust the resolution and/or contrast settings as explained on page 36,
then dial the receiving machine as explained on page 39.
Removing a document from the feeder
If you need to remove
a document from the
feeder, open the
operation panel.
Important!
Do not try to remove a document without opening the operation panel. This
may damage the feeder mechanism.
1 Open the operation panel.
2 Remove the document.
• If the document does not come out
easily, follow the procedure on page
106.
3 Close the operation panel, pressing
down firmly on both front corners to
make sure it clicks into place.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
Adjusting the Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a
document.
You must adjust the
The default resolution
settings each time
setting is STANDARD
you don’t want to use
the default settings.
setting is AUTO.
and the default contrast
Note: The resolution and contrast settings are only effective for sending a
document. They are not effective for receiving a document.
Resolution settings
STANDARD
Use STANDARD for ordinary documents. This
setting gives you the fastest and most
economical transmission.
FINE
Use FINE for documents containing small letters
or fine drawings.
SUPER FINE
HALF TONE
Use SUPER FINE for documents containing
very small letters or very fine drawings.
Use HALF TONE for photographs and
illustrations. The original will be reproduced in
64 shades of gray.
Contrast settings
AUTO
DARK
Use AUTO for normal documents.
Use DARK for faint documents.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
1 Load the document(s).
• The document must be loaded before
the resolution and contrast can be
adjusted.
Display:
STANDARD :AUTO
RESOLUTION/
2 Press
one or more times
RECEPTION MODE
until the desired resolution and
contrast settings appear in the display.
• The first time you move through the list
of resolution settings, the contrast
setting AUTO will appear next to each
resolution setting. The second time you
move through the list, the contrast
setting DARK will appear.
FINE
:AUTO
SUPER FINE :AUTO
HALF TONE :AUTO
STANDARD :DARK
FINE
:DARK
SUPER FINE :DARK
HALF TONE :DARK
Note: In order to transmit in SUPER FINE resolution, the receiving fax machine
must also have that resolution. If it doesn’t, your machine will automatically step
down to the next best available setting.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
Changing the default resolution
If desired, you can change the default resolution for faxing documents to
FINE. Follow the steps below.
FUNCTION
1 Press
once and
3 times.
Display:
OPTION SETTING
FINE PRIORITY
2 Press
once.
1=YES, 2=NO
3 Press
once.
The display briefly shows
your selection, then:
4 Press
to set the default resolution
to set it to STANDARD.
1
to FINE, or
2
NUMBER OF RING
5 Press
to return to the date and time display.
STOP
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Normal Dialing
Sending a Fax by Normal Dialing
SPEAKER
With Normal Dialing, you pick up the handset (or press
pressing the number keys.
) and dial by
♦ If a person answers, you can talk with them through the handset before
SPEAKER
sending the fax. (If you pressed
talk.)
, you must pick up the handset to
♦ Normal Dialing allows you to listen to the line and make sure the other fax
machine is responding.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
SPEAKER
2 Pick up the handset or press
.
SPEAKER
or
Listen for the dial tone.
ABC
JKL
TUV
DEF
1
4
2
5
8
0
3
6
3 Dial the number of the receiving
machine by pressing the number keys.
GHI
MNO
WXYZ
PQRS
7
9
4 Wait for the connection. Depending on the setting of the receiving
machine, you will either hear a fax tone or the other person will answer.
• If the other party answers, ask them to press their Start key (if you pressed
SPEAKER
, pick up the handset to speak with them). This causes the
receiving machine to issue a fax tone.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
START/
MEMORY
5 When you hear the fax tone, press
. Replace the handset.
• If the transmission is completed successfully, the machine will beep once.
• If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 87).
Sending a Fax by Automatic Dialing
You can dial a fax or phone number by simply pressing a Rapid Key, or by
SPEED DIAL
pressing
and entering a two-digit number.
♦ To use Automatic Dialing, you must first store the full fax or phone number
in your fax machine.
♦ When you store a fax or phone number, you select a two-digit Speed Dial
number for it. Ninety-nine Speed Dial numbers are available.
01
Speed Dial numbers 01
through 18 are for Rapid
Key (one-touch) Dialing.
Speed Dial numbers 19
through 99 are for
START/
SPEED DIAL
MEMORY
9
1
SPEED DIAL
dialing with
.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Rapid Keys
Attach the Rapid
Key labels above
the Rapid Keys.
01
02
03
04
05
06
07
13
08
14
09
15
10
11
12
16/POLL
17/G1
18/G2
1
4
7
2
5
8
0
3
6
9
SPEED DIAL
When you store a number in a
Rapid Key, write the name of
the party on the label.
Storing fax and phone numbers for automatic dialing
Display:
FUNCTION
1 Press
once and
once.
<NEW NUMBER>
ENTER FAX #
2 If you know the Speed Dial number that
you want to use, enter that number (for
example, press
for Speed Dial 01).
0
1
Speed Dial numbers 01 to 18
can be used for Rapid Key
Dialing. Speed Dial numbers 19
to 99 are only for Speed Dialing.
Otherwise, press once (the
machine will suggest an available
Speed Dial number at the end of the
storing procedure).
3 Enter the fax or phone number by pressing the number keys.
(Note: A space cannot be entered.)
SPEAKER
• To clear a mistake, press
.
• If a pause is required between any of the digits to access a special service
or an outside line, press
FUNCTION . The pause appears as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
START/
MEMORY
4 Press
.
5 Enter a name by pressing number keys for each letter as shown in the
chart below. Up to 20 characters can be entered. (If you do not wish to
enter a name, go directly to Step 6.)
Example: SHARP = 7777 44 2 777
7
G =
H =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after
entering the first letter.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears.
♦ To enter one of the following symbols, press
or
repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
START/
MEMORY
6 Press
.
If you selected a Speed Dial number in Step 2, the display will briefly
show STORED, and then <NEW NUMBER>. Go to Step 7.
If you did not select a Speed Dial number in Step 2, the display will show
the next available Speed Dial number. If that number is acceptable,
START/
MEMORY
press
press
and go to Step 7. If not, enter the desired two digit number,
, and go to Step 7.
START/
MEMORY
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
7 Return to Step 2 to store another number, or press
to return to the
STOP
date and time display.
Editing and clearing auto-dial numbers
If you need to make changes to a previously stored auto-dial number, or clear
a number, follow these steps:
Display:
FUNCTION
1 Press
once and
once.
<NEW NUMBER>
2 Enter the 2-digit Speed Dial number that you wish to edit or clear (for
example, press
), or press
or
until the number
0
1
appears in the display.
1=EDIT, 2=CLEAR
3 Press
.
4 Press
for EDIT or
• If you selected CLEAR, go to Step 8.
5 If you selected EDIT, make the desired changes to the number.
for CLEAR.
1
2
• Press or to move the cursor to the digit or digits you wish to
change, and then enter the new digit. The new digit will replace the old
digit.
• If you do not wish to change the number, go directly to Step 6.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
START/
MEMORY
6 Press
.
7 Make the desired changes to the name.
• Press or to move the cursor to the letter or letters you wish to
change, and then press the appropriate number key repeatedly until the
desired letter appears (see Step 5 on page 42). The new letter will replace
the old letter.
• If you do not wish to change the name, go directly to Step 8.
START/
MEMORY
8 Press
.
9 Return to Step 2 to edit or clear another number, or press
to return
STOP
to the date and time display.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Rapid Key Dialing
If the number you want to dial has been stored as a Speed Dial number from
01 to 18, you can dial it by pressing the corresponding Rapid Key.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
2 Press the Rapid Key corresponding to
the desired Speed Dial number.
01
• The name of the receiving party will
appear in the display. If no name was
stored, the fax number will appear. (If
the name or number is incorrect, press
Example: To dial Speed
Dial number 01, press
Rapid Key 01.
STOP .)
• The document will be automatically
transmitted once the connection is
established.
• If the transmission is completed successfully, the machine will beep once.
• If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 87).
Using a Rapid Key for a voice call
To use a Rapid Key for a voice call, simply lift the handset and then press the
Rapid Key.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Speed Dialing
Speed Dialing can be used to dial any number that has been stored as a
Speed Dial number.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
SPEED DIAL
2 Press
and then enter the 2-digit Speed Dial number.
• For example, to enter Speed Dial number 19, press
.
1
9
3 Check the display. If the name or number shown is correct, press
START/
MEMORY
. (If not, press
and repeat Step 2.)
STOP
• If the transmission is completed successfully, the machine will beep once.
• If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 87).
Using a Speed Dial number for a voice call
SPEED DIAL
To use a Speed Dial number for a voice call, lift the handset, press
and enter the Speed Dial number.
,
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Searching for an auto-dial number
If you don’t remember the Rapid Key or Speed Dial number in which you have
stored a full fax or phone number, follow these steps to search for the number.
1 If you are sending a fax, load the
document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
Z
A
REDIAL
2 Press
(or
) until the name of the other party appears in the
display (if no name was stored, the number will appear).
START/
MEMORY
3 If you are sending a fax, press
. Dialing and transmission begins.
• If the transmission is completed successfully, the machine will beep once.
• If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 87).
If you are making a phone call, lift the handset. Dialing begins. (If you
START/
MEMORY
lifted the handset before searching for the number, press
begin dialing.)
to
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Sending a fax by Direct Keypad Dialing
You can also enter a full number with the number keys and then press the
START/
MEMORY
key to begin dialing. You can use this method to dial a full number
when you don't need to speak to the other party before faxing.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
2 Enter the number of the receiving machine by pressing the number
keys.
• If a pause is required between any of the digits to access a special service
or an outside line, press
FUNCTION . The pause will appear as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
3 Check the display. If the number of the receiving machine shown is
START/
MEMORY
correct, press
.
• If the number is not correct, press
to backspace and clear one digit at
STOP
a time, and then re-enter the correct digit(s).
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Redial
You can automatically redial the last number dialed on the fax machine. This
procedure can be used to send a fax or make a phone call.
1 If you are sending a fax, load the
document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
Z
REDIAL
2 Press
once. <REDIAL> appears in the display, followed by the
last number dialed. Make sure the number that appears is the number
you wish to dial.
START/
MEMORY
3 If you are sending a fax, press
. Dialing begins.
If you are making a phone call, lift the handset. Dialing begins.
Automatic redialing
If you use automatic dialing (including Direct Keypad Dialing) to send a fax
and the line is busy, the fax machine will automatically redial the number. The
fax machine will make three redial attempts at intervals of five minutes. During
this time, RECALLING will appear in the display, followed by a two-digit
number assigned to the fax job. You will not be able to dial any other locations
while the message appears.
♦ You can press
to clear the message and stop automatic redialing.
STOP
♦ Under certain conditions (for example if a person answers the call on a
telephone), automatic redialing may stop before three redialing attempts
are made.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Error Correction Mode
The fax machine is set to automatically correct any distortions in a
transmission due to noise on the telephone line before printing at the
receiving end. This function is called Error Correction Mode (ECM). ECM is
effective for both transmissions and receptions, and is only effective when the
other fax machine has ECM as well.
When there is considerable noise on the line, you may find that transmission
with ECM turned on takes longer than normal. If you prefer a faster
transmission time, you can try turning ECM off.
FUNCTION
1 Press
once and
3 times.
Display:
OPTION SETTING
ECM MODE
2 Press
once and
3 times.
3 Press
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
to select YES, or
to
1
2
select NO.
DAY LIGHT SAVE
5 Press
to return to the date and time display.
STOP
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Batch Page Numbering
Batch Page Numbering
You can change the page numbering of the transmitted document from simple
numbering ("P.01", "P.02", etc.) to batch numbering, which means that a slash
and the total number of pages being sent are added after each page number
(for example, "P. 01/05", "P.02/05", etc.). This allows the recipient to check for
missing pages.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
Display:
FUNCTION
2 Press
once and
once.
PAGE COUNTER
ENTER # (01 - 99)
3 Press
once.
4 Enter the total number of pages (“01” to “99”) by pressing the numeric
keys.
Example: 5 pages
0
5
5 Dial the receiving machine and send the fax.
♦ If you need to cancel a batch number entry, remove the document from the
feeder or press
.
STOP
♦ If the number of pages actually transmitted does not coincide with the batch
number entered, the alarm will sound and PAGE COUNT ERROR will
appear in the display. PAGE E. will also appear in the NOTE column of the
Transaction Report if printed.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
Sending a Fax From Memory
You can scan a document into the fax’s memory and send the document from
memory. This increases transmission speed and allows you to send a fax to
multiple destinations in a single operation. After transmission, the document is
automatically cleared from memory.
Note: If a power failure occurs while sending a fax from memory, you will need
to repeat the operation.
Broadcasting (sending a fax to multiple destinations)
This function allows you to send the same fax to as many as 20 different
destinations in just one operation.
♦ When sending to multiple destinations, only auto-dial numbers can be used
to dial the numbers of the receiving machines.
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
START/
MEMORY
2 Press
.
3 Select a destination using one of the following methods:
Press a Rapid Key.
SPEED DIAL
Press
and enter a 2-digit Speed Dial number.
Press
or
until the name of the destination appears in the display
(if no name was stored, the number will appear).
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
4 Press
to store the destination.
5 Repeat Steps 3 and 4 for each of the other destinations to which you
wish to send the fax (maximum of 20).
START/
MEMORY
6 When you are ready to begin transmission, press
.
• A Transaction Report is automatically printed out after Broadcasting is
completed. Check the "Note" column of the report to see if any of the
destinations are marked "Busy" or have a communication error code. If so,
send the document to those destinations again.
Broadcasting using a Group Key
If the fax machines to which you want to broadcast have all been programmed
into one Group Key (see Storing numbers in Group Keys which follows), you
can perform the broadcasting operation using the following simplified
procedure:
1 Load the document(s).
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
READY TO SEND
17/G1
2 Press the appropriate Group Key.
Transmission will begin.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
Storing numbers in Group Keys
Group Keys allow you to send a fax to a group of fax machines by simply
pressing the appropriate Group Key once. To store a group of numbers in a
Group Key, follow the steps below.
♦ Rapid Keys 17/G1 and 18/G2 can be used as Group Keys. A key cannot be
simultaneously programmed as both a Group Key and a Rapid Key.
♦ Up to 20 numbers can be stored in one Group Key.
Only Rapid Key and Speed Dial numbers can be stored in a Group Key. Full
numbers cannot be stored.
Display:
FUNCTION
1 Press
once and
twice.
ENTRY MODE
GROUP ENTRY
2 Press
once and
once.
1=SET, 2=CLEAR
3 Press
.
GROUP SET
4 Press
to program a Group Key.
to clear a Group Key.)
1
(Press
2
PRESS GROUP KEY
(Example)
5 Press the Group Key that you wish to
17/G1
program (Rapid Key 17/G1 or 18/G2).
(If you are clearing a Group Key, press
the Group Key that you wish to clear
and go to Step 9.)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
6 Select a destination using one of the following methods:
Press a Rapid Key.
SPEED DIAL
Press
and enter a 2-digit Speed Dial number.
Press
(or
) until the name of the destination appears in the
display (if no name was stored, the number will appear).
7 Press
to store the destination.
8 Repeat Steps 6 and 7 for each of the other destinations that you want to
store in the Group Key (maximum of 20).
START/
MEMORY
9 When you have finished storing the destinations, press
.
10 Press
to return to the date and time display.
STOP
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
Memory transmission
You can also send a fax through memory when sending to a single
destination. This is convenient when sending to destinations where the line is
often busy, as it saves you from waiting to pick up the original document and
frees the feeder for other operations.
START/
MEMORY
To send a fax through memory, load the document, press
dial using one of the following methods:
, and then
START/
MEMORY
♦ Press the number keys to enter the fax number and then press
.
START/
MEMORY
♦ Press a Rapid Key and then press
.
START/
MEMORY
SPEED DIAL
♦ Press
, enter a 2-digit Speed Dial number, and press
.
START/
MEMORY
♦ Press
repeatedly to select an auto-dial number and then press
.
Z
REDIAL
♦ Press
once to select the last number dialed and then press
START/
MEMORY
.
If the memory becomes full...
If the memory becomes full while the document is being scanned, MEMORY
IS FULL will appear in the display.
START/
MEMORY
♦ Press
if you want to transmit the pages which have been stored up
to that point in memory. The remaining pages will be ejected from the
feeder. After transmission, the memory will be cleared and you can transmit
the remaining pages. You will also need to transmit the page which was
being scanned when the memory filled up.
♦ Press
if you want to cancel the entire transmission.
STOP
56
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Receiving Faxes
Using FAX Mode
To select FAX mode, press
RESOLUTION/
(with no document
RECEPTION MODE
in the feeder) until the arrow in
the display points to FAX.
TEL FAX
A.M.
RESOLUTION/
RECEPTION MODE
When the reception mode is set to FAX, the fax machine will automatically
answer all calls on four rings and receive incoming faxes.
♦ If you pick up the handset before the machine answers, you can talk to the
other party and/or receive a fax as explained in Using TEL Mode on page
58.
4 rings
Fax reception
Changing the number of rings
If desired, you can change the number of rings on which the fax machine
answers incoming calls in FAX mode. Any number from 2 to 5 can be
selected.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
NUMBER OF RING
ENTER (2-5) (4)
2 Press
once and
once.
once.
3 Press
4 Enter the desired number of rings (any
The display briefly shows
your selection, then:
number from 2 to 5).
FAX REMOTE #
Example: 3 rings
3
5 Press
to return to the date and time display.
STOP
Note: If you are using Distinctive Ring, the fax machine will answer calls after
two rings regardless of the above setting.
Using TEL Mode
To select TEL mode, press
RESOLUTION/
(with no document
RECEPTION MODE
in the feeder) until the arrow in
the display points to TEL.
TEL FAX
RESOLUTION/
RECEPTION MODE
A.M.
When the reception mode is set to TEL, you must answer all calls (even fax
calls) by picking up the fax machine’s handset or an extension phone
connected to the same line.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
Answering with the fax’s handset
1 When the fax machine rings, pick up
the handset.
Beep
2 If you hear a fax tone, wait until the
RECEIVING
display shows RECEIVING and then
replace the handset.
Note: If you have set the Fax Signal Receive
START/
MEMORY
setting to NO, press
to begin reception.
3 If the other party first speaks with you
START/
and then wants to send a fax, press
RECEIVING
MEMORY
START/
MEMORY
after speaking. (Press before
the sender presses their Start key.)
• When RECEIVING appears in the
display, hang up.
Answering on an extension phone connected to the same
line
1 Answer the extension phone when it
rings.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
2 If you hear a soft fax tone, wait until your fax responds (you will hear
pronounced, high-pitched tones), then hang up.
Beep
Pronounced, high-pitched
tones
3 If the fax doesn't respond, or if the other party first talks to you and then
wants to send a fax, press
once and
twice on the extension
5
phone (only on a tone dial phone). This signals the fax to begin
reception. Hang up.
• The above step is necessary if you have set the Fax Signal Receive setting
to NO.
• Your fax will not accept the signal to begin reception (
) if a
5
document is loaded in its feeder.
Optional Reception Settings
Fax Signal Receive
Your fax will automatically begin reception if you hear a soft fax tone after
answering a call on your fax or an extension phone. If you use a computer fax
modem to send documents on the same line, you must turn this function off in
order to prevent your fax from mistakenly attempting to receive documents
from the computer fax modem. Follow the steps below to change the setting.
FUNCTION
1 Press
once and
3 times.
Display: OPTION SETTING
FAX SIGNAL RX
2 Press
once and
7 times.
1=YES, 2=NO
3 Press
once.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
The display briefly shows
your selection, then:
4 Press
to turn on the function, or
1
POLLING
to turn it off.
2
5 Press
to return to the date and time display.
STOP
Changing the number for remote fax activation
If desired, you can use a number other than 5 to activate fax reception from an
extension telephone. You can select any number from 0 to 9.
FUNCTION
Display:
OPTION SETTING
FAX REMOTE #
1 Press
once and
3 times.
2 Press
once and
twice.
ENTER (0-9) (5)
3 Press
once.
4 Enter the desired number (any number
The display briefly shows
your selection, then:
from 0 to 9).
TRANSACTION
Example:
3
5 Press
to return to the date and time display.
STOP
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
Reception Ratio
The fax has been set at the factory to automatically reduce the size of
received documents to fit the size of the printing paper. This ensures that data
on the edges of the document are not cut off. If desired, you can turn this
function off and have received documents printed at full size.
♦ If a document is too long to fit on the printing paper, the remainder will be
printed on a second page. In this case, the cut-off point may occur in the
middle of a line.
♦ Automatic reduction may not be possible if the received document is too
large, contains too many fine graphics or images, or is sent at high
resolution. In this case, the remainder of the document will be printed on a
second page.
Display:
FUNCTION
1 Press
once and
twice.
PRINT SET-UP
RECEIVE RATIO
2 Press
once.
1=AUTO, 2=100%
3 Press
once.
The display briefly shows
your selection, then:
4 Press
to select AUTO, or
to
2
1
select 100%.
PAPER SIZE SET
5 Press
to return to the date and time display.
STOP
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Substitute Reception to Memory
Substitute Reception to Memory
In situations where printing is not possible, such as when your fax runs out of
paper, the print cartridge needs replacement, or the paper jams, incoming
faxes will be received to memory.
When you have received a document in memory, FAX RX IN MEMORY will
appear in the display, alternating with ADD PAPER & PRESS START KEY,
COVER OPEN, PAPER JAMMED, OUT OF INK, or PRINTER ERROR /
START/
MEMORY
CHECK PAPER. When you add paper (and press
), or clear the jam, or
replace the print cartridge, the stored documents will automatically print out.
♦ If you received documents in memory because the fax ran out of paper, be
sure to add paper which is the same size as the paper previously used. If
not, the document print-out size may not match the size of the printing
paper.
Caution!
♦ When documents are stored in memory, do not turn the power off. This will
erase all of the contents.
♦ If documents received in memory are lost due to a power failure or other
interruption in the power supply, a CLEAR REPORT will be printed out
when the power is restored. This gives information about the receptions
lost, including the fax numbers of the transmitting machines if they are
available.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Making Copies
Your fax machine can also be used to make copies. Single and multiple copies
(up to 99 per original) can be made, enabling your fax to double as a
convenience office copier.
1 Load the document(s) face down.
(Maximum of 20 letter pages or 5 legal
pages.)
RESOLUTION/
• If desired, press
to set
RECEPTION MODE
the resolution and/or contrast.
(The default resolution setting for
copying is FINE.)
READY TO SEND
2 Select any of the following copy settings as needed:
• Enlarge/reduce: Press or until the desired setting appears
in the display. Settings are 100%, 125%, 135%, 200%, 70%, 88%, 94%,
and AUTO (automatic adjustment to match the size of the paper). The
default setting is 100%.
Example: Press
twice
COPY RATIO: 125%
• Number of copies per original: Press the number keys to enter a number
from 1 to 99. The default setting is 1.
Example: Press
for two copies
2
2
• Sorted copies: To sort the copies as shown below under “Sorted”, first set
the number of copies per original (at least “2” copies must be set), and then
SPEED DIAL
press
.
2
[SORT]
Originals
C
Example of two
copies each of
three originals
B
A
Not sorted (MULTI COPY)
Sorted (SORT COPY)
A
B
C
C
C
A
B
B
B
C
A
A
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Copies
COPY/HELP
3 When you are ready to begin copying, press
.
If MEMORY IS FULL appears...
If you place a large number of originals in the feeder, the memory may
become full before all pages can be scanned (the display will show MEMORY
START/
MEMORY
IS FULL). If this happens, press
to copy the pages that have been
scanned, and then repeat the copy procedure for the remaining pages,
including the page that was being scanned when the memory became full.
Copy Cut-off
When making a copy of a document that is longer than the printing paper, use
the copy cut-off setting to select whether the remaining part of the document
will be cut off or printed on a second page. The initial setting is YES (cut off
the remainder). To change the setting, follow the steps below.
Display:
FUNCTION
1 Press
once and
twice.
PRINT SET-UP
COPY CUT-OFF
2 Press
once and
twice.
1=YES, 2=NO
3 Press
once.
The display briefly shows
your selection, then:
4 Press
to set copy cut-off to YES
1
(the remaining part of the document
INK SAVE MODE
will not be printed), or
to set copy
2
cut-off to NO (the remaining part will be
printed on a second page).
5 Press
to return to the date and time display.
STOP
65
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Answering Machine Connection
Connecting an Answering Machine
If desired, you can connect an answering machine to your fax machine's TEL.
SET jack This will allow you to receive both voice messages and faxes when
you are out.
♦ Important: If the answering machine is not connected to the TEL. SET jack
on the fax as shown, the setup will not operate properly.
1 Remove the seal covering the TEL.
SET jack.
TEL.SET
TEL.LINE
2 Connect the answering machine's telephone line jack to the TEL. SET
jack.
• If desired, you can connect an extension phone to your answering
machine's extension phone jack.
TEL.SET
TEL.LINE
Make sure the
TEL. LINE
jack is
connected to
To answering machine's
the wall jack.
telephone line jack.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Answering Machine Connection
Changing the outgoing message
The outgoing message (OGM) of your answering machine should be changed
to inform callers who want to send a fax to press their Start key. For example,
your message might go as follows:
"Hello. You've reached the ABC company. No one is available to take your call
right now. Please leave a message after the beep or press your facsimile Start
key to send a fax. Thank you for calling."
♦ It is advisable to keep the length of the message under 10 seconds. If it is
too long, you may have difficulty receiving faxes sent by automatic dialing.
♦ If your outgoing message must be longer than 10 seconds, leave a pause
of about four seconds at the beginning of the message. This will give your
fax a chance to detect fax tones sent when automatic dialing is used.
Using the Answering Machine Connection
When you go out, activate the answering machine connection as follows:
1 Set the reception mode to A.M.
TEL FAX
RESOLUTION/
RECEPTION MODE
A.M.
2 Set your answering machine to auto answer.
♦ Your answering machine must be set to answer on a maximum of two rings.
If not, you may not be able to receive faxes sent by automatic dialling.
♦ If your answering machine has a toll saver function, make sure that it will
answer by the fourth ring.
Note: If your answering machine has a remote retrieval function, make sure the
code used to activate remote retrieval is different from the code used to activate
fax reception with an extension telephone (see page 61). If they are the same,
entering the code from an outside telephone to retrieve messages will cause the
fax machine to be activated.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional A.M. Mode Settings
How answering machine mode operates
While you are out, all of your incoming calls will be answered by your
answering machine and its outgoing message will play. Voice callers can
leave a message. During this time, your fax will quietly monitor the line. If your
fax detects a fax tone or a duration of silence greater than four seconds, it will
take over the line and begin reception.
♦ If the connection is not good or there is noise on the line, the answering
machine and/or fax machine may not respond properly.
♦ The call counter on your answering machine may indicate that voice
messages were received, when only fax messages were received.
♦ To prevent the fax from taking over the line and beginning reception if you
call in from an external phone or answer on an extension phone, press any
three keys (other than the code to activate fax reception, "5", "*", and "*")
on the dial pad of the phone. This can only be performed from a phone
capable of tone dialling.
When you return and turn off
your answering machine, be
sure to change the reception
mode back to FAX or TEL!
Optional A.M. Mode Settings
If necessary, you can use the following settings to improve the response of the
answering machine connection to incoming calls.
Quiet Detect Time
This function causes the fax machine to take over the line and begin reception
if a certain duration of silence is detected after the answering machine
answers.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional A.M. Mode Settings
Time selections for the period of silence are 1 to 10 seconds. Quiet Detect
Time has been set to 4 seconds at the factory. This gives the best
performance with most answering machines; however, you may need to
adjust this setting depending on the disconnect time of your answering
machine.
Some answering machines may have unusually fast disconnect times (equal
to or very slightly less than 4 seconds), which means that the answering
machine may disconnect the line before fax reception can begin. In this case,
try a Quiet Detect Time setting of about 3 seconds.
If the fax machine is interrupting callers before they can leave a message, try
a longer Quiet Detect Time setting. If your outgoing message includes a
period of silence, make sure that the setting is longer than that period of
silence, or re-record your outgoing message to shorten the silence.
Note: Quiet Detect Time can be turned off by entering "00" for the time. Note,
however, that the fax machine will not be able to receive faxes sent manually by
Normal Dialing.
To change the setting, follow the steps below.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
QUIET TIME
2 Press
once and
5 times.
ENTER (00-10) 04
3 Press
once.
The display briefly shows
your selection, then:
4 Enter a number from 01 to 10, or enter
00 to turn off the function.
QUIET START
Example: 3 seconds
0
3
5 Press
to return to the date and time display.
STOP
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional A.M. Mode Settings
Quiet Detect Start Time
This setting can be used to delay the start of the Quiet Detect Time function.
For example, if you want to insert a pause at the beginning of your answering
machine’s outgoing message to ensure clear detection of fax signals, you can
use this setting to delay the start of silence detection so that the pause will not
cause the fax to take over the line.
Quiet Detect Start Timing has been set to five seconds at the factory. You can
change this setting by entering a 2-digit number equal to the desired number
of seconds of the delay, or turn the function off by enttering 00. As general
guide, the delay time should be slightly longer than the pause before the
outgoing message.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
2 Press
once and
6 times.
QUIET START
3 Press
once.
ENTER (00-15) 05
4 Enter a 2-digit number (from 01 to 15)
The display briefly shows
your selection, then:
for the number of seconds of the delay,
or enter 00 to turn off the function.
ON TAD FAILURE
Example: 3 seconds
0
3
5 Press
to return to the date and time display.
STOP
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional A.M. Mode Settings
On TAD Failure
When this function is turned on, your fax will answer the call after 5 rings if the
answering machine for some reason fails to answer before that time. This
ensures that you will receive fax messages even if the answering machine’s
tape fills up or the answering machine is not turned on.
This function has been turned off at the factory. If you want to turn it on, follow
the steps below:
Note:
When this function is turned on, make sure that the answering machine is set to
answer on 4 rings or less. If it isn’t, the fax will always answer first, preventing
callers from leaving voice messages.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
2 Press
once and
7 times.
ON TAD FAILURE
3 Press
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
to turn on the function, or
1
to turn it off.
DISTINCTIVE
2
5 Press
to return to the date and time display.
STOP
71
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Special Functions
Caller ID (Requires Subscription to Service)
If you subscribe to a caller identification service from your telephone
company, you can have the fax machine display the name and number of the
caller when you receive a call.
Important:
To use this function, you must subscribe to a caller identification service from
your telephone company. Note that your fax may not be compatible with some
caller identification services.
♦ Area Code mode: This step is needed if your telephone exchange cannot
dial a local phone number (within your calling area code) when the area
code is dialed with the phone number (see Step 5).
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
CALLER-ID
2 Press
once and
5 times.
1=YES, 2=NO
3 Press
once.
AREA CODE # MODE
1=SET, 2=CLEAR
4 Press
(YES) to turn on Caller ID.
1
(To turn off Caller ID, press
to Step 8.)
and go
2
5 Press
to select SET.
(To clear a previously set area code,
press and go to Step 8.)
1
ENTER AREA CODE
2
Note: Entering your area code in this step causes it to be automatically removed
from local numbers in the Caller ID list (page 74). This is only required if you need
to eliminate dialing of the area code when dialing a local number from the list.
Example (using the area code “123”): If Step 5 is skipped, the Caller ID display will
show 123-444-1234, and the number that will dial from the Caller ID list is 123-
444-1234. If the area code 123 is entered in Step 5, the Caller ID display will show
444-1234, and the number that will dial from the Caller ID list is 444-1234.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
6 Enter the three digits of your area code.
START/
AUTO PRINT OUT
MEMORY
7 Press
to store your area code.
8 Press
to return to the date and time display.
STOP
How Caller ID operates
When you receive a call, the name and phone number of the caller will appear
in the display, beginning just before the second ring. The information will
continue to be displayed until the line is disconnected.
Display example
JOHN DOE
525-8693
Caller’s name
Caller’s number
Note: Some caller ID services may not provide the name of the caller. In this case,
only the phone number will appear.
Display messages
One of the following messages will appear while the fax rings if caller
information is not available.
NO SERVICE
No caller information was received from your telephone
company. Make sure that the telephone company has
activated your service.
CALLER-ID ERROR Noise on the telephone line prevented reception of
caller information.
OUT OF AREA
The call was made from an area which does not have a
caller identification service, or the caller’s service is not
compatible with that of your local phone company.
PRIVATE CALL
Caller information was not provided by the telephone
company at the caller’s request.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
Viewing the Caller ID list
If you subscribe to a Caller ID service and have turned on the Caller ID
function, your fax machine will keep information on the most recent 30 calls
and faxes you have received. You can view this information, which consists of
the name and number of each caller, in the Caller ID List.
♦ After you have received 30 calls, each new call will delete the oldest call.
Follow the steps below to view the Caller ID List in the display. If desired, you
can immediately dial a number when it appears.
Z
<REVIEW CALLS>
REDIAL
1 Press
twice.
2 Press
or
to scroll through the list.
3 If you wish to dial one of the numbers in the list, scroll through the list
until the number appears in the display.
• Fax: If you wish to send a fax, load the
START/
MEMORY
Fax:
document and then press
.
START/
MEMORY
Dialing and transmission begin.
• Voice call: If you wish to make a voice
call, pick up the handset (or press
SPEAKER
). Dialing begins automatically.
Voice
call:
SPEAKER
(If you pressed
, pick up the
handset when the other party answers.)
4 Press
when you have finished viewing the list.
STOP
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
To delete calls from the Caller ID list
If you want to delete a single call from the caller list, press
while the call
0
appears in the display. If you want to delete all calls from the list, hold
down for at least 3 seconds while you are viewing any number in the list.
0
Priority Call
If you have turned on Caller ID, you can set the machine to make a special
ringing sound when you receive a call from a designated phone number. This
lets you know immediately who is calling without having to look at the display.
To use this function, enter the desired phone number by following the steps
below (only one phone number can be entered).
FUNCTION
1 Press
once and
twice.
Display:
ENTRY MODE
PRIORITY #
2 Press
once and
twice.
1=SET, 2=CLEAR
3 Press
once.
4 Press
to store a number.
1
(To clear a previously stored number, press
and go to Step 6.)
2
5 Enter the number by pressing the number keys (max. 20 digits).
START/
MEMORY
GROUP ENTRY
6 Press
to store (or clear) the number.
7 Press
to return to the date and time display.
STOP
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
Blocking voice calls
If you have turned on Caller ID, you can use the Anti Junk Fax function
described in Blocking Reception of Unwanted Faxes in this chapter to block
voice calls as well as faxes from your specified Anti Junk Number.
In this case, when a voice call or a fax transmission comes in from the number
you have specified as a "Junk Number", your fax will break the connection as
soon as it receives the calling phone number from the caller ID service (before
the second ring).
To use this function, enter the number that you wish to block as explained in
Blocking Reception of Unwanted Faxes (see page 79). Only one number can
be blocked.
Note: This function cannot be used if you are using the Distinctive Ring function.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Subscription to Service)
Distinctive Ring (Requires Subscription to
Service)
Important:
♦ To use distinctive ring, you must subscribe to a distinctive ring
service from your local phone company.
♦ Note that your fax machine may not be compatible with some distinctive
ring services.
Distinctive ring is a service offered by some local telephone companies
whereby they assign an additional second number to your regular single line.
The second number rings differently from your normal number.
If you subscribe to a distinctive ring service, you can set the fax machine to
automatically answer when your second number is called. This allows you to
use the second number as an exclusive fax number. To have your fax
automatically answer when your second number is called, follow the steps
below:
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
DISTINCTIVE
2 Press
once and
8 times.
3 Press
once.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Subscription to Service)
4 Press a number from 1 to 3 to select the ring pattern below that matches
your second number’s ring pattern. Press 4 to have your fax
automatically answer your normal telephone number. Press 5 to turn off
the distinctive ring function.
RING PATTERN 1
RING PATTERN 2
RING PATTERN 3
STANDARD RING
OFF SETTING
Two short rings
1
One short, one long, and one short ring
Two short rings and one long ring
Your standard (normal) ring pattern
Turn distinctive ring off
2
3
4
5
The display briefly shows
your selection, then:
FAX SIGNAL RX
5 Press
to return to the date and time display.
STOP
6 Set the reception mode to FAX.
TEL FAX
A.M.
RESOLUTION/
RECEPTION MODE
♦ When using distinctive ring, you must set the reception mode of your fax
machine to FAX. When your designated fax number is dialed, your fax will
automatically answer and begin reception after two rings. Note that other
devices on the same line will also ring until your fax answers. If one of your
other numbers is dialed, the fax will ring; however, it will not answer.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking Reception of Unwanted Faxes
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes from a party
that you specify. This saves paper by not printing out unwanted "junk" faxes.
To use this function, follow the steps below to enter the fax number from which
you do not wish to receive faxes. One fax number can be entered.
Display:
FUNCTION
1 Press
once and
twice.
ENTRY MODE
ANTI JUNK #
2 Press
once and
3 times.
1=SET, 2=CLEAR
3 Press
once.
4 Press
to store an Anti Junk number, or
to clear a previously
1
2
stored number (if you are clearing a number, go to Step 6).
5 Enter the fax number by pressing the number keys (max. 20 digits).
START/
MEMORY
6 Press
and then press
to return to the date and time display.
STOP
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Polling (Requesting a Fax Transmission)
Polling allows you to call another fax machine and have it send a document
(previously loaded in its feeder) to your machine without operator assistance.
In other words, the receiving fax machine, not the transmitting fax machine,
initiates the transmission.
To use the polling function, you must first set Rapid Key 16/POLL for use as a
polling key.
♦ When Rapid Key 16/POLL is set as a polling key, it cannot be used for
Rapid Key dialing.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
POLLING
2 Press
once and
6 times.
1=YES, 2=NO
3 Press
once.
The display briefly shows
your selection, then:
4 Press
to use Rapid Key 16/POLL
1
as a polling key.
CALLER-ID
(To turn off the polling function, press
.)
2
5 Press
to return to the date and time display.
STOP
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Requesting transmission
1 Dial the fax machine you want to poll using one of the following
methods:
• Pick up the handset (or press the SPEAKER key) and dial the full number.
Wait for the fax answerback tone.
• Pick up the handset (or press the SPEAKER key) and press a Rapid Key.
Wait for the fax answerback tone.
• Press the SPEED DIAL key and enter a 2-digit Speed Dial number.
• Enter the full number using the numeric keys.
16/POLL
2 Press
.
• If you used the handset, replace it when POLLING appears in the display.
Reception will begin.
Being polled (polling standby)
RESOLUTION/
To let another fax machine poll your fax, press
reception mode to FAX and load the document(s).
to set the
RECEPTION MODE
Transmission will take place when the other fax machine calls your machine
and activates polling. Automatic reception is possible while your fax is on
polling standby.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Polling security
Polling Security allows you to prevent unauthorized polling of your machine.
When this function is turned on, polling will only take place when the fax
number of the polling fax machine has been entered in your machine's list of
permitted fax numbers (called "passcode numbers"). The number of the
polling fax must also be correctly programmed into itself for identification.
To use Polling Security, follow the steps below to turn the function on, and
then enter permitted numbers as explained on the following page.
FUNCTION
Display:
ENTRY MODE
SECURITY
1 Press
once and
twice.
2 Press
once and
once.
1=ON, 2=OFF
3 Press
.
4 Press
to turn on polling security.
to turn off polling security.)
1
(Press
2
The display briefly shows
your selection, then:
START/
MEMORY
5 Press
.
PASSCODE MODE
6 Press
to return to the date and time display.
STOP
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Storing fax numbers for polling permission
You can store up to 10 fax numbers in your machine's list of permitted
numbers.
FUNCTION
Display:
1 Press
once and
twice.
ENTRY MODE
PASSCODE MODE
2 Press
once and
twice.
<NEW CODE>
ENTER FAX #
3 Press
.
.
4 Press
5 Enter the fax number (maximum of 20 digits).
START/
<NEW CODE>
MEMORY
6 Press
.
7 Return to Step 4 to store another number, or press
to return to the
STOP
date and time display.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Editing and clearing polling permission numbers
If you need to make changes to a previously stored polling permission
number, or clear a number, follow these steps:
FUNCTION
Display:
ENTRY MODE
1 Press
once and
twice.
PASSCODE MODE
2 Press
once and
twice.
<NEW CODE>
3 Press
.
4 Press
or
until the number you want to edit or clear appears
in the display.
1=EDIT, 2=CLEAR
5 Press
.
6 Press
for EDIT or
for CLEAR.
2
1
• If you selected CLEAR, go to Step 8.
7 If you selected EDIT, make the desired changes to the number.
• Press
or
to move the cursor to the digit or digits you wish to
change, and then enter the new digit. The new digit will replace the old digit.
START/
<NEW CODE>
MEMORY
8 Press
.
9 Return to Step 4 to edit or clear another number, or press
to return
STOP
to the date and time display.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Printing Lists
You can print lists showing settings and information entered in the fax
machine, and a report showing recent fax transactions. The lists and report
are described below. To print a list or report, follow these steps.
Display:
FUNCTION
1 Press
once and
once.
LISTING MODE
ACTIVITY LIST
2 Press
once.
or
3 Press
until the desired list appears in the display.
PRESS START KEY
4 Press
once.
START/
MEMORY
5 Press
to print the list.
Activity Report
This report shows information on your most recent 30 fax transactions. The
report is divided into two parts: the TRANSMISSIONS ACTIVITY REPORT,
which shows information on fax transmissions, and the RECEPTIONS
ACTIVITY REPORT, which shows information on fax receptions.
♦ All information is erased after a report is printed out. If information on 30 fax
transactions accumulates, the information on the oldest transaction will be
deleted each time a new transaction takes place.
♦ You can have the Activity Report printed out automatically each time
information on 30 fax transactions accumulates. See page 89.
♦ The Activity Report contains the same headings as the Transaction Report.
See page 87 for an explanation of the headings.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Telephone Number List
This list shows the fax and phone numbers that have been stored for
automatic dialing.
Group List
This list shows the fax numbers that have been stored in each Group Key.
Setup List
This list shows your current selections for the FUNCTION key settings. The
list also shows your name and fax/telephone number as entered in the
machine, and a sample of the header printed at the top of every page you
transmit (HEADER PRINT).
Caller-ID List
This list shows information on your 30 most recently received calls and faxes.
(This list is only available if you are using the Caller ID function.)
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report
This report is printed out automatically after an operation is completed to
allow you to check the result. Your fax machine is set at the factory to print out
the report only when an error occurs.
♦ The Transaction report cannot be printed on demand.
Headings in the Transaction Report
SENDER/
RECEIVER
The name or fax number of the other machine involved in the
transaction. If that machine does not have an ID function, the
communication mode will appear (for example, "G3").
START
The time at which transmission/reception started.
Total time taken for transmission/reception.
Number of pages transmitted/received.
TX/RX TIME
PAGES
NOTE
(One of the following notes will appear under NOTE in the
report to indicate whether the transaction was successful,
and if not, the reason for the failure.)
OK - Transmission/reception was successful.
P.FAIL - A power failure prevented the transaction.
JAM - The printing paper or document jammed, preventing
the transaction.
BUSY - The fax was not sent because the line was busy.
COM.E-X - (Where “X” is a number.) A telephone line error
prevented the transaction. See Line error on page 98.
CANCEL - The transaction was cancelled because the
STOP key was pressed, no document was in the feeder, or
the other machine requested transmission using a function
which your fax machine does not have. If you were
attempting to fax, make sure a document is in the feeder. If
you were receiving, contact the faxing party to see how they
are trying to send to you.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report print condition
You can change the condition under which a Transaction Report is printed out.
Follow the steps below.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
TRANSACTION
2 Press
once and
3 times.
1:ALWAYS PRINT
3 Press
once.
(Selections appear alternately)
4 Press a number from
to
to select the condition for printing.
1
5
1
ALWAYS PRINT
A report will be printed after each
transmission, reception, or error.
2
3
ERROR/MEMORY
SEND ONLY
A report will be printed after an error or a
memory operation.
A report will be printed after each
transmission.
4
5
ERROR ONLY
NEVER PRINT
A report will be printed only when an error
occurs.
A report will never be printed.
The display briefly shows
your selection, then:
DIAL MODE
5 Press
to return to the date and time display.
STOP
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Auto print-out of Activity Report
You can set the Activity Report to print automatically whenever information on
30 fax transactions has accumulated. (A report can still be printed on demand
at any time.) Follow these steps:
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
AUTO PRINT OUT
2 Press
once and
4 times.
1=YES, 2=NO
3 Press
once.
The display briefly shows
your selection, then:
4 Press
to turn on auto print out, or
1
ECM MODE
to turn it off.
2
5 Press
to return to the date and time display.
STOP
89
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
Cleaning the Machine
Cleaning the scanning glass and rollers
Clean the scanning glass and rollers frequently to ensure the quality of
transmitted images and copies.
1 Open the operation panel.
2 Flip up the green levers on each side of
the white roller.
3 Wipe the scanning glass (under the
white roller) and rollers with a cotton
swab.
• Make sure that all dirt and stains (such
as correcting fluid) are removed. Dirt
and stains will cause vertical lines on
transmitted images and copies.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
If the scanning glass is difficult to clean
If you find it difficult to remove dirt from the scanning glass, you can try moistening
the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol
gets on the rollers.
4 Flip down the green levers on each
side of the white roller.
5 Close the operation panel, pressing
down firmly on both front corners to
make sure it clicks into place.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Rotating the white roller
After cleaning the scanning glass and rollers as explained in the preceding
procedure, follow the steps below to make the machine rotate the white roller
by half a turn, and then repeat the cleaning procedure. This will enable you to
clean the side of the roller that was initially facing down.
♦ Do not perform this procedure when a document is loaded in the feeder.
This may cause the top part of the document to be cut off when the
document is faxed or copied.
Display:
FUNCTION
1 Press
once and
3 times.
OPTION SETTING
CLEAN ROLLER
2 Press
once and
once.
3 Press
once.
START/
MEMORY
4 Press
.
• The white roller rotates half a turn. When rotation is finished, the machine
will beep.
Cleaning the housing
Wipe the external parts and surface of the machine with a dry cloth.
Caution!
Do not use benzene or thinner. These solvents may damage or discolor the
machine.
About the lithium battery:
The fax machine uses a lithium battery to retain settings and information
programmed in the machine when the power is turned off. Battery power is
consumed primarily when the power is off. With the power kept continuously off,
the life of the battery is about 5 years. If the battery dies, have your dealer or
retailer replace it. Do not try to replace it yourself.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Improving Print Quality
Aligning the print cartridge
If print quality is not satisfactory, first try aligning the print cartridge.
Note: Make sure that paper is loaded before beginning this procedure.
Display:
FUNCTION
1 Press
once and
twice.
PRINT SET-UP
ALIGN CART.
2 Press
once and
twice.
1=PRINT,2=SET
3 Press
once.
4 Press
to print an alignment page.
1
(To enter an alignment value without
printing an alignment page, press
.)
2
5 In the alignment page that the machine prints, locate the line that comes
closest to forming a completely straight line.
In this example, “15”
comes closest to
forming a straight line.
After printing the alignment
page the display shows:
ENTER (0-30) 15
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
6 Press the number keys to enter the number of the straightest line.
Example:
1
5
• If you make a mistake, press
and then repeat the entry.
STOP
START/
MEMORY
CLEAN NOZZLES
7 Press
.
8 Press
to return to the date and time display.
STOP
Cleaning the print cartridge nozzles
If print quality is still not satisfactory after aligning the print cartridge, follow
these steps to clean the print cartridge nozzles.
Display:
FUNCTION
1 Press
once and
twice.
PRINT SET-UP
CLEAN NOZZLES
2 Press
3 Press
4 Press
once and
once.
PRESS START KEY
once.
START/
MEMORY
.
• The machine prints a test pattern similar to the one shown in the following
step.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
5 Compare the diagonal line above the printed bars to the diagonal line
below the printed bars.
• Look for a break in the diagonal line above the bars. A break indicates
clogged nozzles.
Breaks in the
diagonal line at
the top of the
page indicate
clogged nozzles.
Unbroken lines at the bottom of the page
indicate the nozzles were cleaned.
6 If the bottom diagonal line still has breaks, repeat Steps 1 and 2 to run
the nozzle test again. Run the test a third time if necessary.
• If the print quality is satisfactory after running the nozzle test three times,
the nozzles are clean.
• If the print quality is still not satisfactory after running the test a third time,
continue with Step 7.
7 Open the operation panel and then the print compartment cover, and
remove and reinstall the print cartridge (see page 17).
8 Repeat the nozzle test. If the lines are still broken, wipe the nozzles as
explained in the following section.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Wiping the print nozzles and contacts
If you have cleaned the print nozzles as explained in the previous section at
least three times and print quality is still not satisfactory, try wiping the print
nozzles and contacts.
1 Open the operation panel and then the print compartment cover, and
remove the print cartridge (see page 17).
• CAUTION! DO NOT touch the gold contact area of the cartridge or the
contact area of the cartridge carriage with your fingers.
2 Dampen a clean cloth with water, and
gently wipe the nozzles and the gold-
colored area around the nozzles. Wipe
in one direction only.
• To dissolve dried ink, hold the damp
cloth against the nozzles for about
three seconds. Gently blot and wipe
dry.
• When finished, allow the gold-colored
area to dry.
3 Dampen another section of clean cloth
with water, and gently wipe the
contacts and the gold-colored area
around the contacts.
• To dissolve dried ink, hold the damp
cloth against the contacts for about
three seconds. Gently blot and wipe
dry.
• When finished, allow the gold-colored
area to dry.
4 Reinstall the print cartridge and repeat the nozzle test as explained in
the previous section.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the cartridge holder
A dirty print cartridge holder may cause smudges on your printed pages. To
clean the print cartridge holder, open the operation panel and then the print
compartment cover, and remove the print cartridge (see page 17). Wipe ꢀ
on the holder with a damp cloth.
1
97
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Troubleshooting
Problems and Solutions
If you have any problems with your fax, first refer to the following
troubleshooting guide. If you cannot solve the problem, call Sharp's Customer
Assistance Center at 1-877-794-8675.
Line error
Problem
Solution
LINE ERROR appears in
the display.
A line error occurs when your fax machine cannot
communicate correctly with the other fax machine.
The error is usually due to a problem on the phone
line.
Try the transaction again. If the error persists, check
the following:
• Check the connection. The cord from the TEL.
LINE jack to the wall jack should be no longer than
six feet.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the fax machine to a different
telephone line.
• If the problem still occurs, your fax machine may
need service.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Dialing and transmission problems
Problem
Solution
No dial tone when you
pick up the handset or
press the SPEAKER key.
• Make sure the handset cord is connected to the
correct jack. See Connecting the handset on page 11.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack (see page 11).
• Make sure that the telephone line is good.
Dialing is not possible.
• Make sure the power cord is properly plugged into a
power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack (see page 24).
• Make sure that the fax machine is set to the correct
dialing mode for your telephone line. See Dial mode
on page 24.
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• Make sure that the telephone line cord is plugged into
the TEL. LINE jack, and not the TEL. SET jack.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Check the display for error messages.
• Pick up the handset and check for a dial tone. Dial the
receiving machine manually and make sure that it is
responding (you should hear a fax tone).
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion. Try
sending the document again.
• ECM mode (see page 50) will help prevent distortions
due to line noise. Note that ECM mode must be
turned on in the other machine as well.
• Make a copy of the document on your fax machine. If
the copy is also distorted, your fax machine may need
service.
Reception and copying problems
Problem
Solution
The fax machine doesn't
receive documents
automatically.
• Make sure that the reception mode is set to FAX. If
you subscribe to a distinctive ring service, make sure
that the Distinctive Ring function is set to the correct
ring pattern. If you do not subscribe to a distinctive
ring service, make sure that Distinctive Ring is set to
OFF SETTING. (See Distinctive Ring on page 77.)
The printing paper comes • Make sure that the document is loaded properly in the
out blank when you try to
receive a document.
feeder of the transmitting machine. Make a copy or
print a report to confirm the printing ability of your
machine.
Print quality is poor.
• The print cartridge may need alignment or cleaning.
See page 93.
The received document is • Ask the other party to send higher contrast
faint.
documents. If the contrast is still too low, your fax
machine may need service. Make a copy or print a
report to check your machine’s printing ability.
• The print cartridge may need replacement.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document again.
• ECM mode (see page 50) will help prevent distortions
due to line noise. Note that ECM mode must be
turned on in the other machine as well.
• Make a copy or print a report on your fax machine. If
the copy or report is also distorted, your fax machine
may need service.
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will cause
spots to appear on copies and transmitted faxes.
Clean the scanning glass as explained on page 90.
The power is on, but no
reception takes place.
• Make sure that the telephone line cord is plugged into
the TEL. LINE jack, and not the TEL. SET jack.
General problems
Problem
Solution
Nothing appears in the
display.
• Make sure the power cord is properly plugged into a
power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the keys,
unplug the power cord and then plug it in again
several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable Documents on page 33).
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Answering machine connection
Problem
Solution
The answering machine
connection does not
operate properly.
• Make sure your machine's reception mode is set to
A.M..
• Make sure your machine's TEL. LINE jack is
connected to the wall jack. Make sure your machine's
TEL. SET jack is connected to your answering
machine's telephone line jack (not the answering
machine's extension phone jack).
• Make sure your answering machine's outgoing
message is under 10 seconds.
• Make sure that the Quiet Detect Time setting is set to
three or four seconds (see page 68).
• Make sure that the Distinctive Ring function is set to
OFF SETTING (see page 77).
• If you have checked all of the above and the
connection still doesn't operate properly, call the
Customer Assistance Center.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Messages and Signals
Display messages
Note: If you have turned on the Caller ID function, see page 73 for display
messages related to Caller ID.
ADD PAPER & /
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add
paper and then press the START/MEMORY key. If
there is paper in the tray, make sure it is inserted
correctly (take out the stack, align the edges evenly,
and then reinsert it in the tray) and then press the
START/MEMORY key.
CHANGE CARTRIDGE
CHECK CARTRIDGE
This message appears after you install or replace the
print cartridge (see page 19).
The print cartridge is missing and must be installed,
or is not installed correctly.
COVER OPEN
The print compartment cover is open. Close it.
DOCUMENT JAMMED
The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will
occur if you load more than 20 pages at once or load
documents that are too thick (see page 33). The
document may also jam if the receiving machine
doesn’t respond properly when you attempt to send a
fax.
FAX RX IN MEMORY
A fax has been received in memory because the print
cartridge needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will
print out automatically when the problem is fixed.
FUNCTION MODE
INK NEAR EMPTY
The FUNCTION key has been pressed.
The cartridge is nearly empty (approximately one
eighth of the ink remains).
LINE ERROR
Transmission or reception was not successful. Press
the STOP key to clear the message and then try
again. If the error persists, see Line error on page 98.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
LOW INK
The cartridge is low on ink (approximately one
quarter of the ink remains).
MEMORY IS FULL
If faxes have been received to memory because
printing is not possible (an additional message will
indicate the problem), resolve the problem so that
printing can continue (see Substitute Reception to
Memory on page 63).
If you are attempting to transmit from memory, see If
the memory becomes full on page 56.
If you are copying, see If MEMORY IS FULL appears
on page 65.
MEMORY PRINTING
NO # STORED
OFF HOOK
The fax is preparing to or printing out a document
from memory.
This appears if you attempt to search for an auto-dial
number when none have been stored.
This appears if you forgot to replace the handset after
using it to dial and send a fax. Replace the handset or
press the STOP key to clear the message.
ON HOOK DIAL
OUT OF INK
The SPEAKER key has been pressed and the fax
machine is waiting for you to dial.
The cartridge is out of ink and must be replaced.
Faxes will be received to memory.
PAPER JAMMED
PRINTER ERROR
The printing paper is jammed. See page 107.
A printer error has occurred. Open the printer
compartment cover, make sure the print cartridge is
installed correctly, and then close the cover.
PRINTER ERROR/
CHECK PAPER
A paper jam may have occurred. Follow the
procedure on page 107 to clear the jam.
READY TO SEND
A document has been loaded and the fax machine is
waiting for you to begin faxing or copying.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
RECALLING
This appears if you attempt to send a fax by
automatic dialing and the line is busy or the receiving
fax machine does not answer. Your fax machine will
automatically reattempt the call. (See Automatic
redialing on page 49.)
TOTAL PAGE(S) 01
Number of pages transmitted, received, or copied.
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
Rapid intermittent
tone
35 seconds
(0.7 seconds on,
0.3 seconds off)
Indicates that the handset is off hook.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying,
START/
MEMORY
or DOCUMENT JAMMED appears in the display, first try pressing
the document doesn't feed out, remove it as explained below.
. If
Important:
Do not try to remove a jammed document without releasing it as explained
below. This may damage the feeder mechanism.
1 Slowly open the operation panel until it
is half open.
2 Flip up the green levers on each side of
the white roller.
3 Gently remove the document.
• Be careful not to tear the document.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
4 Flip down the green levers on each
side of the white roller.
5 Close the operation panel, pressing
down on both sides to make sure it
clicks into place.
Clearing jammed printing paper
1 Open the operation panel.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
2 Open the print compartment cover.
• Press as shown and pull the cover
toward you.
3 Gently pull the jammed paper out of the
machine, making sure no torn pieces
of paper remain in the print
compartment or rollers.
4 Close the print compartment cover.
5 Close the operation panel, pressing
down firmly on both front corners to
make sure it clicks into place.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Parts
Ordering Parts
To order parts, contact the parts distribution center located nearest
you. When ordering a part, use the part order number shown below.
Operation manual
Setup Guide
TINSE4299XHTZ
TCADH3457XHZZ
Handset cord
QCNWG209BXHOW
QCNWG208BXHZZ
DUNTK443CXHFW
LPLTP2889XHVA/LPLTP2890XHVA
PCOVA2115XHVB
Telephone line cord
Handset
Paper tray / tray extension
Paper tray cover
Document tray
LPLTP3264XHSA
Document exit support
PWIR-2082XHZZ
Part distribution centers
Tritronics, Inc.
1306 Continental Drive
Abingdon, MD 21009
Tel: 1-800-638-3328
Fax: 1-800-888-FAXD
Tritronics, Inc.
Tel:1-800-365-8030
1015 NW 52nd Street
Ft. Lauderdale, FL 33309
Fax: 1-800-999-FAXD
Fox International, Ltd.
23600 Aurora Road
Tel: 1-800-321-6993
Fax: 1-800-445-7991
Bedford Heights, OH 44146
Andrews Electronics
25158 Avenue Stanford
Santa Clarita, CA 91355
Tel: 1-800-274-4666
Fax: 1-805-295-5126
Sharp Accessories and
Supply Center
Tel: 1-800-642-2122
2130 Townline Road
Peoria, IL 61615
109
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Regulatory Information
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted
by the ACTA. On the rear of this equipment is a label that contains, among other
information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details. This equipment connects to the
telephone network through a standard USOC RJ-11C network interface jack.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format US:AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information,
please contact Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If
the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this equipment ID does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
This equipment is hearing-aid compatible.
When programming and/or making test calls to emergency numbers:
♦ Remain on the line and briefly explain to the dispatcher the reason for the call.
♦ Perform such activities in the off-peak hours, such as early morning or late evening.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Revised date:
Issued date :Sep.19.2002
.
MATERIAL SAFETY DATA SHEET (1/3)
MSDS No. B-1028
Section 1. Product Identification
Product Code : Ink-Cartridge (Mono) UX-C70B
Section 2. Supplier’s Name and Address
Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
(Country)
U.S.A.
(Name and Telephone Number)
Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
Emergency telephone number :
1-800-255-3924
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number :
1-800-424-9300
Section 3. Composition / Information for Ingredients
Ingredients
Cas No.
Proportion
OSHA PEL
ACGIH TLV
(% by Weight)
1333-86-4
(2)
1-6
0.1-2
10-20
1-10
0.1-5
>55
3.5 mg/m3 (1)
3.5 mg/m3 (1)
Carbon Black
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
Acrylic Terpolymer
Water Soluble Organic Solvents
Hydroxylated Alkane
Acrylic Resin
(2)
(2)(4)
(2)
7732-18-5
Water
Notes:
(1) Total dust (measured carbon black)
(2) Trade secret of patented molecule.
(3) Specific workplace exposure limits have not been established.
(4) New Jersey Trade Secret Registration Number (NJTSRN) 80100451-5004
Section 4. Hazardous Identification
The following information is based on testing of the ink and on the characteristics of component chemicals:
Primary Routes of Entry:
Ink stains on skin or mucus membranes (mouth, eyes & nose) may cause
discomfort.
Medical Conditions
Aggravated by Exposure: None known at intended levels of use.
POTENTIAL HEALTH EFFECTS:
Inhalation:
Short Term Exposure -- If ink mist is inhaled, respiratory tract irritation may occur.
Long Term Exposure -- No adverse chronic effects expected.
Short Term Exposure -- Ink may be slightly irritating to the skin.
Long Term Exposure -- No adverse chronic effects expected. Not a dermal sensitizer.
Short Term Exposure -- Not an eye irritant.
Long Term Exposure -- No adverse chronic effects expected.
Short Term Exposure -- Low oral toxicity.
Skin Contact:
Eye Contact:
Ingestion:
Long Term Exposure -- No adverse chronic effects known or expected, but based on
component characteristics, gastrointestinal effects, liver and kidney toxicity, and
CNS effects are possible if large quantities of ink are repeatedly ingested.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Revised date:
.
Issued date :Sep.19.2002
MATERIAL SAFETY DATA SHEET (2/3)
MSDS No. B-1028
Section 5. First Aid Measures
Inhalation:
Ingestion:
Remove to fresh air. Seek medical attention if breathing becomes difficult.
Immediately rinse mouth out with plenty of water. If within 30 minutes after ingestion, give
victim a small glass of water or milk (NEVER give anything by mouth to an unconscious
person). Contact physician or poison center. Do not induce vomiting unless instructed to
do so by a physician or poison center.
Skin Contact:
Eye Contact:
Remove contaminated clothing. Flush affected area with water. Seek medical attention
if irritation develops and persists.
Flush immediately with plenty of water. Remove contact lenses and continue flushing for at least
15 minutes. Seek medical attention if irritation develops and persists.
Section 6. Fire Fighting Measures
Flash Point: Not applicable
Flammability Limits(%): Not applicable
Extinguishing Media: Water, foam, carbon, dioxide or dry chemical.
Fire fighting:
Fire may produce small amounts of hazardous decomposition products such as
carbon dioxide, carbon monoxide, and unidentified organics. NIOSH approved
self-contained breathing apparatus may be required if a large volume of ink is
involved.
Fire and Explosion Hazard: No unusual fire or explosion hazards are known for this product.
Hazardous Combustion Products: Oxides of carbon, organic acids, low molecular weight organics.
Section 7. Accidental Release Measures
Occupational Spill:
Absorb small ink spills with cloth or paper towels or other suitable material.
Place in a container for disposal. For large spills, dike around spill with absorbent
material.
Transfer contaminated diking material to separate, suitable containers for recovery
or disposal.
Ventilate area and wash spill site after material pickup is complete.
Unless specifically permitted, keep waste out of sewers, watershed and waterways.
Section 8. Handling and Storage
STORE IN COOL, DRY PLACE
Section 9. Exposure Control/Personal Protection
Ventilation:
Eye Protection:
Mechanical room ventilation
None needed for intended use in printer.
Protective Clothing: None needed for intended use in printer.
Gloves: None needed for intended use in printer.
Section 10. Physical Chemical Characteristics
Description:
Black liquid with faint odor.
No
Freezing Point:
pH:
Approx. -12 to -150 °
7.0-8.5
C
Pressurized:
Water Solubility:
Evaporation Rate
(Butylacetate=1):
Fully Miscible
Percent Volatile:
Specific Gravity:
Vapor Density (Air=1): Approx. 1.6
Approx. 18.7
Approx. 1.0 mg/I
Approx. 3.5
Section 11. Stability and Reactivity
Stability:
Incompatibilities:
None known.
None known.
Thermal decomposition products:
Hazardous polymerization:
Oxides of carbon, acid gases, low molecular weight organics.
This product will not polymerize.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Revised date:
.
Issued date :Sep.19.2002
MATERIAL SAFETY DATA SHEET (3/3)
MSDS No. B-1028
Section 12. Toxicological Information
Acute Toxicity: Not expected to be acutely toxic; LD50 (oral, rat) expected to be >2000 mg/kg.
Chronic Toxicity: Not expected to be chronically toxic based on component information, volume,
concentration, and intended use.
Pure carbon black, a minor component of this ink, has been listed by LARC as group 2B
(possible carcinogen).
This classification is based on rat “lung particulate overload” studies performed with
airborne particulate carbon black.Ink is not listed by LARC, NTP, or OSHA.
OSHA Regulated(USA): Not listed
Carcinogenicity:
In 1996 the LARC reevaluated carbon black as a Group 2B carcinogen (possible human
carcinogen). This evaluation is given to Carbon Black for which there is inadequate
human evidence, but sufficient animal evidence. The latter is based upon the
development of lung tumors in rats receiving chronic inhalation exposures to free
carbon black at levels that induce particle overload of the lung.
Studies performed in animal models other than rats have not demonstrated an
association between carbon black and lung tumors.
Section 13. Ecological Information
No data available.
Section 14. Disposal Consideration
This product is not a listed or hazardous waste in accordance with Federal Regulation 40 CFR Part 261. If
discarded, this product would not be a hazardous waste either by listing or by characteristic. However, it is the
responsibility of the product user to determine at the time of disposal whether a material has been
contaminated and should be classified as a hazardous waste.
In accordance with RCRA 40 CFR Section 264.314 and 265.314, the placement of any liquid in landfills is
prohibited.
Disposal is subject to local, state and federal regulations.
Section 15. Transport Information
DOT PROPER SHIPPING NAME: Not regulated as hazardous material.
Section 16. Regulatory Information
All ingredients are registered under the Toxic Substances Control Act (TSCA) or underpolymer exemption.
All ingredients are exempt, registered or considered registered (polymers) under the European Inventory of
Existing Commercial Chemical Substances(EINECS/ELINCS).
Preparation not classified as dangerous (EU Directive 67/548/EEC;1999/45/EC).
All ingredients are listed on or are considered polymers under the Canadian Domestic Substances List
(DSL) or Non Domestic Substances List (NDSL).
Note of the product ingredients are listed as Emergency Planning and Community Right-to-Know Act
(EPCRA)-Section 302: Extremely Hazardous Substances (EHS).
None of the product components are present above the minimum quantities of listed chemicals in EPCRA
Section 313 Supplier Notification.
This product contains no known materials at levels which the State California has found to cause cancer, birth
defects or other reproductive harm - California Proposition 65.
Section 17. Other Information
Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. This
information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and
accepts no responsibilities for any typographical errors which may appear on these sheets. It is the
responsibility of the user to determine the suitability of this product for each particular use.
Literature Reference:
LARC(1996): LARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol.65,
Printing Process and Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261 H.Muhle,
B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in
Rats.
Fundamental and Applied Toxicology 17, pp.280-299
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Reference Guide
Sending Faxes
Receiving Faxes
Place your document
(up to 20 pages) face
down in the document
feeder.
RESOLUTION/
Press
until the arrow in the
RECEPTION MODE
display points to the desired reception
TEL FAX
mode.
JAN-03 10:30
A.M.
TEL FAX
RESOLUTION/
RECEPTION MODE
JAN-03 10:30
Normal Dialing
A.M.
TEL FAX
JAN-03 10:30
A.M.
SPEAKER
1. Lift the handset or press
2. Dial the fax number.
.
FAX mode: The fax machine automatically
answers and receives faxes.
3. Wait for the reception tone (if a person
answers, ask them to press their Start
key).
TEL mode: Answer all calls (even faxes)
by picking up the handset. To begin fax
START/
MEMORY
reception, press
.
START/
MEMORY
4. Press
.
A.M. mode: Select this mode when you
want to use an answering machine that is
connected to the fax.
Rapid Key Dialing
Press the appropriate Rapid Key.
Transmission will begin automatically.
Storing Auto Dial Numbers
Speed Dialing
FUNCTION
SPEED DIAL
1. Press
once and
once.
1. Press
.
2. Enter the 2-digit Speed Dial number.
2. Enter a 2-digit Speed Dial number (01 to
99; 01 to 18 for Rapid Key Dialing).
START/
MEMORY
3. Press
START/
MEMORY
3. Enter the fax number and press
.
Search Dialing
4. Enter a name by pressing number keys.
(To enter two letters in succession that
Z
A
REDIAL
1. Press
or
until the desired
require the same key, press
entering the first letter.)
after
destination appears in the display.
START/
G =
N =
U =
V =
SPACE =
MEMORY
2. Press
.
A =
H =
O =
P =
Q =
R =
S =
T =
B =
C =
D =
W =
X =
Y =
Z =
I
=
J =
K =
L =
Direct Keypad Dialing
1. Dial the fax number.
E =
F =
M =
START/
MEMORY
START/
MEMORY
2. Press
.
5. Press
and then
.
STOP
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Guía de referencia rápida
Transmisión de documentos
Recepción de documentos
RESOLUTION/
Coloque el documento
(hasta 20 páginas)
mirando hacia abajo
en el alimentador.
Pulse
hasta que la flecha
RECEPTION MODE
del display señale el modo de recepción
TEL FAX
deseado.
JAN-03 10:30
A.M.
TEL FAX
RESOLUTION/
RECEPTION MODE
JAN-03 10:30
A.M.
Marcación normal
TEL FAX
JAN-03 10:30
A.M.
SPEAKER
Modo FAX: El aparato de telefax
contestará y recibirá documentos
automáticamente.
1. Levante el auricular o pulse
.
2. Marque el número de telefax.
3. Espere a escuchar el tono de recepción
(si alguien contesta el teléfono, pídale
que pulse su tecla Inicio).
Modo TEL: Contesta todas las llamadas
(incluso las de telefax) levantando el
auricular. Para que comience la
recepción del documento, pulse
START/
START/
4. Pulse
.
MEMORY
.
MEMORY
Modo A.M.: Seleccione este modo si
desea utilizar un contestador automático
Marcación por tecla rápida
conectado al aparato de telefax.
Pulse la Tecla rápida apropiada.
La transmisión comenzará
automáticamente.
Programación de números de
marcación automática
Marcación abreviada
FUNCTION
1. Pulse
una vez y
una vez.
SPEED DIAL
1. Pulse
.
2. Introduzca un número de 2 dígitos de
Marcación abreviada (01 a 99; 01 a 18
para una Marcación por tecla rápida).
2. Introduzca el número de 2 dígitos de
marcación abreviada.
START/
3. Introduzca el
número de telefax y pulse
START/
3. Pulse
.
MEMORY
MEMORY
.
Marcación por búsqueda
4. Introduzca un nombre pulsando las
teclas numéricas. (Para introducir dos
letras sucesivas que requieran la
Z
A
REDIAL
1. Pulse
o
hasta que
misma tecla, pulse
después de
aparezca el número deseado en el
introducir la primera letra).
display.
G =
N =
U =
V =
SPACE =
START/
2. Pulse
.
A =
H =
MEMORY
O =
P =
Q =
R =
S =
T =
B =
C =
D =
W =
X =
Y =
Z =
I
=
J =
K =
L =
Marcación directa por teclado
E =
F =
1. Marque el número de telefax.
M =
START/
2. Pulse
.
MEMORY
START/
MEMORY
5. Pulse
y, a continuación,
.
STOP
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Distinctive ring, 77
Document feeder, 34
Document guides, 34
Document restrictions, 34
Document sizes, 33
A
Activity Report, 85
Activity Report, Auto Print Out, 89
AM reception mode, 30, 67
Answering machine connection
Activating, 67
Document, maximum scanning size, 33
Connecting, 66
E
On TAD Failure, 71
Quiet Detect Start Time, 70
Quiet Detect Time, 68
Troubleshooting, 102
Anti Junk Fax, 79
ECM (Error Correction Mode), 50
Extension telephone
Connecting, 25
Using, 59
Audible signals, 105
Auto-dial numbers
F
Searching for, 47
FAX reception mode, 30, 57
Fax Signal Receive, 60
Storing, 41
Fine resolution priority, 38
B
Batch page numbering, 51
Broadcasting, 52-53
G
Group Keys, 54
Group List, 86
C
Caller ID, 72-76
Caller ID List, 86
Contrast, 36
Copies, 64
Copy cut-off setting, 65
H
Halftone setting, 36
Handset, 11
Handset receiver volume, 32
Housing, cleaning, 92
D
I
Date, setting, 28-29
Daylight Saving Time, 29
Dial mode, 24
Ink save mode, 23
J
Dialing
Jams, clearing, 106-108
Direct Keypad, 48
Normal, 39
L
Rapid Key, 45
Searching, 47
Letters, entering, 27, 42
Line error, 98
Loading paper, 14
Speed, 46
Direct Keypad Dialing, 48
Display messages, 73, 103
Loading the document, 34
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
M
S
Memory transmission, 56
Scanning glass, cleaning, 90
Memory, substitute reception to, 63
Sender’s name and number, entering,
26-27
Setup List, 86
Speaker volume, 31
Speed Dialing, 46
N
Normal dialing, 39
Number of rings in FAX reception mode,
57
T
TEL reception mode, 30, 58
TEL. LINE jack, 24
O
Ordering parts, 109
TEL. SET jack, 25, 66
Tel/Fax Remote Number, 61
Telephone line cord, 24
Telephone Number List, 86
Time, setting, 28-29
P
Page numbering, batch, 51
Paper jams, clearing, 106-108
Paper size setting, 22
Paper trays, 12
Transaction Report, 87
Setting print condition, 88
Paper, loading, 14
Polling, 80-83
Power cord, 16
Print cartridge
Aligning, 93-94
Cleaning nozzles, 94
Installing, 17-21
Wiping nozzles, 96
Print cartridge holder, wiping, 97
Priority Call, 75
R
Rapid Key Dialing, 45
Reception mode
AM mode, 30, 67
FAX mode, 30, 57
TEL mode, 30, 58
Reception Ratio setting, 62
Redialing, 49
Removing original document, 35
Resolution, 36
Ringer volume, 32
Roller, rotating for cleaning, 92
117
Download from Www.Somanuals.com. All Manuals Search And Download.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under appli-
cable state law, implied warranties may not validly be disclaimed or excluded, the duration of such
implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product:
Personal Facsimile
Warranty Period for this Product:
Additional items excluded
from warranty coverage:
Where to obtain service:
Ninety (90) days parts and labor from date of purchase.
Any consumable items such as paper supplied with the
Product.
At a Sharp Authorized Servicer located in the United States.
To find out the location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to obtain service:
Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer.
Be sure to have proof of purchase available. If you ship or mail the
Product, be sure it is packaged carefully.
For product information or customer assistance, please visit http://www.sharpusa.com on the
World Wide Web or call 1-800-BE SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-1163
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163
SHARP CORPORATION
FOR YOUR RECORDS
Please record the model number and serial number below, for easy
reference, in case of loss or theft. These numbers are located on the
rear side of the unit.Space is also provided for other relevant
information.
Model Number
Serial Number
UX-B700
Date of Purchase
Place of Purchase
PRINTED IN THAILAND
(TINSE4299XHTB)
Download from Www.Somanuals.com. All Manuals Search And Download.
|