MODEL
FO-D60
FACSIMILE
OPERATION MANUAL
1. Installation
2. Using the Cordless Handset
3. Using the Answering System
4. Sending Faxes
5. Receiving Faxes
6. Making Copies
7. Special Functions
8. Printing Lists
9. Maintenance
10. Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Welcome, and thank you for choosing a SHARP fax machine and cordless
handset.
In addition to the cordless handset that is included with the fax machine, up to
five other cordless handsets can used with the fax machine. The additional
cordless handsets must support the DECT/GAP standard.
The FO-D60 base (fax machine) complies with the GAP (Generic Access
Prophile) standard and supports the following functions: Outgoing calls,
incoming calls, intercom.
Additional bases and handsets must comply with the GAP standard.
Fax machine and general specifications
Automatic dialling
Imaging film
40 numbers
Initial starter roll (included with machine):
10 m (approx. 30 A4 pages)
Replacement roll (not included):
FO-9CR 60 m (one roll yields
approx. 180 A4 pages)
Memory size*
Modem speed
448 KB (approx. 24 average pages with no
voice messages recorded and ECM turned off,
or 20 minutes of voice messages (including
OGMs) with no documents in memory)
14,400 bps with automatic fallback to lower
speeds.
Transmission time*
Resolution
Approx. 6 seconds (only when ECM is on)
Horizontal: 8 lines/mm
Vertical:
Standard: 3.85 lines/mm
Fine /Halftone: 7.7 lines/mm
Super fine: 15.4 lines/mm
10 pages max. (A4, 80 g/m2 paper)
Thermal transfer recording
Automatic document feeder
Recording system
*Based on Sharp Standard Chart at standard resolution is Sharp special mode, excluding
time for protocol signals (i.e., ITU-T phase C time only).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Halftone (grayscale)
Compression scheme
64 levels
MR, MH, MMR
Paper tray capacity
(60 - 80 g/m2 paper)
Approx. 50 A4-size sheets
(at room temperature; maximum stack height
should not be higher than the line on the tray)
Display
16-digit LCD display
Applicable telephone line
Compatibility
Analog public switched telephone network
ITU-T (CCITT) G3 mode
Input document size
Automatic feeding:
Width: 148 to 210 mm
Length: 140 to 297 mm
Manual feeding:
Width: 148 to 210 mm
Length: 140 to 600 mm
Effective scanning width
Effective printing width
Contrast control
210 mm max.
204 mm max.
Automatic/Dark selectable
TEL/FAX,TEL, FAX, A.M.
Single / Multi (99 copies/page)
Yes (cannot be used if power fails)
230 - 240 V AC, 50 Hz
5 - 35°C
Reception modes
Copy function
Telephone function
Power requirements
Operating temperature
Humidity
25 - 85 % RH
Power consumption
Standby: 3.2 W
Maximum: 110 W
Dimensions (without
attachments)
Width: 327 mm
Depth: 193 mm
Height: 163 mm
Weight (without
Approx. 2.8 kg
attachments)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Cordless handset specifications
Standard
DECT (Digital Enhanced Cordless
Telecommunications)
GAP (Generic Access Profile)
Frequency
1.88 to 1.9 GHz
Duplex operation
Dimensions
TDMA (Time Division Multiple Access)
Width: 51 mm
Depth: 29 mm
Height: 145 mm
Weight
Battery
Approx. 130 g (with battery)
1.2 V Ni-MH battery; capacity: 630 mAh x 3 pcs
(min. 600 mAh)
Power consumption
Initial charging
Battery life
Battery life in standby
mode
Approx. 1.0 W (in standby mode)
Approx. 12 hours for initial charge
Approx. 10 hours (600 minutes) (at room temp.)
Approx. 120 hours with one full charge (at room
temperature)
Battery life (both normal and in standby mode)
may vary depending on usage, range from
base machine, and environmental conditions
such as temperature.
As a part of our policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
System PIN number
Please fill in your system PIN in the space provided below. For information on the System PIN
number, see page 57.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety information
For your safety, if any of your equipment is not operating properly or should any physical
damage occur to the equipment where internal parts may become exposed, the equipment
should be immediately disconnected from the phone line and then the power line and returned
to a SHARP authorised Service Centre for inspection, repair, or disposal.
Installing or modifying telephone lines should only be done by an ACA licensed serviceman.
This facsimile machine is designed for use in Australia only.
Do not disassemble this machine or attempt any procedures not described in this manual.
Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do not use the
machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a
swimming pool. Take care not to spill any liquids on the machine.
Unplug the machine from the telephone socket and then the power outlet and consult a
qualified service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine where people
may walk on the power cord.
This machine must only be connected to a 230 - 240 V, 50 Hz, earthed (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the warranty.
Never insert objects of any kind into slots or openings on the machine. This could create a risk
of fire or electric shock. If an object falls into the machine that you cannot remove, unplug the
machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be seriously
damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone sockets in wet locations unless the socket is specifically designed for
wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be
a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily accessible.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING NOTICE:
NO calls can be made to or from this fax machine during a mains power failure.
WARNING: Australian Communications Authority (ACA) regulations state that no unauthorised
changes or modifications to this equipment are permitted.
Note: Complies with ACA standard AS/NZSCISPR22 regarding emission of electromagnetic
interference.
These limits are designed to provide reasonable protection against interference in an
installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause interference. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a different circuit to that which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
The Ringer Equivalence Number (REN) for this equipment is written on the back of the
machine. The sum of all Ringer Equivalence Numbers (REN's) on your telephone line should
not exceed 3 to assure correct service from your telephone company.
Batteries
Use only the batteries specified in this manual. Use only the provided charger to charge the
batteries.
Do not use new and old batteries together. Do not use different types of batteries together.
When replacing batteries, make sure that the "+" and "-" sides are placed correctly.
Do not mutilate the batteries. Corrosive fluid may leak out and cause injury or burns to the
eyes and skin. The fluid may be toxic if swallowed. In case of contact with eyes, flush with
clean water (do not rub), and seek medical attention immediately.
Do not store or carry a battery with other metal objects such as keys or pins. These may short
the battery and cause it to overheat.
Do not allow a battery to become wet.
Do not dispose of a battery in a fire or heat a battery. The battery may explode.
Do not let children replace the batteries.
Do not attempt to recharge a non-rechargeable battery.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Health care facilities and equipment
Radio frequency energy emitted from the cordless handset equipment may cause medical
equipment to malfunction. Verify that any personal medical equipment you are using is
adequately shielded from external radio frequency energy before using the cordless handset
equipment. Do not use the cordless handset equipment in health care facilities where such
use is prohibited.
Important: This fax machine is not designed for use on a line which has call waiting, call
forwarding, or certain other special services offered by your telephone company. If you attempt
to use the fax machine in conjunction with any of these services, you may experience errors
during transmission and reception of facsimile messages. The fax machine is not compatible
with digital telephone systems.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
A Look at the Operation Panel
9
1. Installation
15
Unpacking Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Loading the Imaging Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Loading Printing Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Volume Adjustment - Fax Machine. . . . . . . . . . . . . . . . . . . . . . . . . . 33
2. Using the Cordless Handset
35
About the Cordless Handset System . . . . . . . . . . . . . . . . . . . . . . . . 35
Making a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Receiving a Phone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Receiving a Fax Using the Cordless Handset . . . . . . . . . . . . . . . . . 38
Storing and Using Auto-Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . 38
Dialling From the Incoming/Outgoing Call List (Redial) . . . . . . . . . . 44
Using the Intercom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Transferring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting the Ringing Melody and Volume. . . . . . . . . . . . . . . . . . . . 50
Other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Registering Cordless Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3. Using the Answering System
63
Recording an Outgoing Message. . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Operating the Answering System. . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Optional Answering System Settings . . . . . . . . . . . . . . . . . . . . . . . . 68
Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Remote Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4. Sending Faxes
81
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Adjusting the Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . 83
Sending a Fax by Normal Dialling. . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Sending a Fax by Automatic Dialling . . . . . . . . . . . . . . . . . . . . . . . . 87
Sending a Fax From Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5. Receiving Faxes
96
Using TEL/FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Using A.M. Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Using FAX Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Using TEL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Optional Reception Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Substitute Reception to Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . 104
6. Making Copies
105
7. Special Functions
107
Caller ID (Requires Subscription to Service) . . . . . . . . . . . . . . . . . 107
Distinctive Ring (Requires Subscription to Service) . . . . . . . . . . . . 112
Blocking Reception of Unwanted Faxes . . . . . . . . . . . . . . . . . . . . . 113
Polling (Requesting a Fax Transmission) . . . . . . . . . . . . . . . . . . . . 114
8. Printing Lists
115
9. Maintenance
118
Replacing the Cordless Handset Batteries . . . . . . . . . . . . . . . . . . . 121
10. Troubleshooting
123
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Quick Reference Guide
Index
136
138
8
Download from Www.Somanuals.com. All Manuals Search And Download.
A Look at the Operation Panel
1
2
3
4
5
6
7
8
9
ABC
JKL
TUV
DEF
RESOLUTION
TEL FAX
1
4
2
5
8
3
6
GHI
MNO
RECEPTION
MODE
TEL/FAX A.M.
STOP
REC/
MEMO
PLAY/
HOLD
PQRS
WXYZ
COPY/HELP/POLL
START/MEMORY
7
9
Z
A
INTERCOM
FUNCTION
REDIAL
0
REPEAT
SKIP
DELETE
13
14
15 16 17 18
10 11
12
key
1
Press this key to listen to the line and fax tones through the speaker when
faxing a document (page 85).
RESOLUTION key
Press this key to adjust the resolution for faxing or copying (page 83).
2
3
RECEPTION MODE key
Press this key to select the reception mode (an arrow in the display will point
to the currently selected reception mode; page 32).
REC/MEMO key
4
5
6
Press this key to record an outgoing message, phone conversation, or memo
(pages 63 and 67).
PLAY/HOLD key
Press this key to play recorded messages (page 66), or to place a call on hold
(page 101).
Display
This displays messages and prompts to help you operate the machine.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
UP and DOWN arrow keys
7
Enlarge/reduce setting: When making a copy of a document, press these
keys to select an enlarge/reduce setting (page 105).
Volume setting: When a document is not in the feeder, press these keys to
change the speaker volume when the
key has been pressed, or the
ringer volume at any other time (page 34).
FUNCTION key settings: Press these keys after pressing the FUNCTION
key to scroll through the FUNCTION MODE settings.
Number keys
8
9
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
Panel release
Press this release to open the operation panel.
STOP key
10
11
Press this key to cancel an operation before it is completed.
COPY/HELP/POLL key
Press this key to make a copy of a document (page 105). Press this key to
print out the Help List, a quick reference guide to the operation of the fax
machine. This key is also used after dialling to poll (request fax transmission
from) another machine (page 114).
START/MEMORY key
Press this key after dialling to begin fax transmission (page 85). Press this key
12
before dialling to send a fax through memory (page 95).
13 INTERCOM key
Press this key to page or locate the cordless handset.
Left and right arrow keys
14
15
Auto-dial numbers: When sending a fax or making a phone call, press these
keys to scroll through your auto-dial numbers (page 90), the “REVIEW
CALLS” list (only available if you have Caller ID; page 109), and the last
number dialled (redial; page 92).
FUNCTION key settings: Press the right arrow key after scrolling with the up
and down arrow keys to select a FUNCTION key setting.
FUNCTION key
Press this key followed by the arrow keys to select special functions and
settings.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT key
16
17
Press this key while listening to a message to play it again (page 66).
SKIP key
Press this key while listening to a message to skip to the next message (page
66).
DELETE key
18
Press this key to erase recorded messages (page 67).
Monitoring phone conversations
When speaking through the handset, you can press
to allow a third
person to listen to the conversation through the speaker. (To turn off the
speaker, press the key again.)
To adjust the volume of the speaker when monitoring a conversation, press
or
(the volume reverts to the lowest setting each time the handset
is replaced).
Note that the speaker cannot be used for speaking; it is only for listening.
To avoid feedback (a loud howling sound), be sure to turn off the speaker
(press
once again) before you replace the handset.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cordless handset
1
2
8
3
4
5
9
10
11
6
7
Display
1
This displays messages and prompts to help you use the cordless handset.
key
2
Press
and received on the cordless handset (received calls will only appear if you
have Caller ID). If you have Caller ID, you can hold down to access the
and then
or
to scroll through the most recent calls made
Caller ID list in the fax machine. During a phone conversation, this key can be
pressed to issue a flash signal. If you are on a flash-type PBX, this key can be
used to dial out.
key and
key
3
Receiver volume: When talking on the cordless handset, press these keys to
adjust the receiver volume.
Scroll through option settings: When not talking on the cordless handset,
press these keys to scroll through the option settings. To select a setting,
press
.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
key
4
Press this key to end a call. To turn off the power of the cordless handset,
hold down this key until the display goes blank.
key
5
6
Use this key to clear an entry, or to move back to the previous level in the
settings. Press this key during a call to put the other party on hold.
Number keys
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
7
8
key
When entering an auto-dial number, hold this key down until a hyphen
appears to insert a pause between digits.
key
Use this key to search for an auto dial number (press
and then
or
to scroll through your auto-dial numbers). If you hear a fax tone when you
answer a call, press this key to begin fax reception.
9
key
Press this key to make or answer a call. To turn on the power of the cordless
handset when it is off, hold down this key until the display turns on .
10
11
key
Press this to select settings and complete entries when programming
information in the cordless handset.
Battery cover
Remove this cover to install or replace the handset battery.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Icons in the cordless handset display
1
2
3
4
5
--1--
This indicates how much power is left in the batteries.
1
This indicates that the cordless handset ringer (and the beeps that sound
when keys are pressed) are turned off (silent ring).
2
This appears when
a call comes in.
is pressed on the cordless handset, and blinks when
3
4
This appears when new messages have been received in the fax machine’s
answering system. The envelope flap opens when there are only old
messages.
This appears when the cordless handset and the fax machine are able to
communicate.
5
Characters that appear in the cordless handset display
1 2 3 4 5 6 7 8 9 0
Note that lower case letters in the fax
machine display will appear as upper case
letters in the cordless handset display, and a
letter with an umlaut will appear as a space.
In addition, the following characters appear
differently in the fax machine and cordless
handset displays:
A B C D E F G H I
J
Fax machine
.
/
!
´´
#
$
% &
’
K L M N O P Q R S T
Cordless handset
(
)
+
Fax machine
,
-
:
]
;
<
U V W X Y Z
-
pause
#
Cordless handset
[
Fax machine
=
`
>
{
? @
¥
ˆ
-
Cordless handset
? _
|
}
Fax machine
Cordless handset
:space
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Installation
Unpacking Checklist
Before setting up, make sure you have all of the following items.
♦ If any are missing, contact your dealer or retailer.
Adapter
Paper tray
extension
Operation
manual
Gears (2)
Paper tray
Imaging film
(initial starter roll)
Handset
Handset
cord
Telephone line
cord
Rechargeable
batteries (3)
Cordless
handset charger
Cordless
handset
Battery
cover
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Setting Up
Selecting a location for the fax machine
To maximize the talking range of the cordless handset, we recommend
installing the fax machine in a high and central location away from
obstructions such as walls.
High and central
location with no
obstructions
Keep the fax machine away
from other electrical
appliances such as TVs,
microwave ovens,
computers, and other
cordless phones.
Do not place the
machine near
heaters or air
conditioners.
Do not place the
machine in direct
sunlight.
Keep dust away from Keep the area
the machine.
around the
machine clear.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset
cord goes into the jack
marked with a handset
symbol on the side of
the machine!
Use the handset to make ordinary phone calls,
or to transmit and receive faxes manually.
Connecting the power cord
Plug the power cord into a 230 - 240 V, 50 Hz, earthed AC (3-prong) outlet.
♦ When disconnecting the fax, unplug the telephone line cord before
unplugging the power cord.
♦ Caution: The power outlet must be installed near the equipment and must
be easily accessible.
The machine does not
have a power on/off
switch, so the power is
turned on and off by
simply plugging in or
unplugging the power
cord.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Connecting the telephone line cord
Insert one end of the telephone line cord into the adapter. Insert the other end
of the line cord into the socket on the back of the machine marked TEL. LINE.
Plug the adapter into the telephone socket on the wall.
Be sure to insert
the line into the
TEL. LINE socket.
Do not insert it
TEL.SET
into the TEL. SET
TEL.LINE
socket!
Setting the dial mode:
The fax machine is set for tone dialling. If you are on a pulse dial line, you
must set the fax machine for pulse dialling. Press the keys on the operation
panel as follows:
Display:
FUNCTION
1 Press
once and
twice.
OPTION SETTING
2 Press
3 Press
once and
twice.
DIAL MODE
1=TONE, 2=PULSE
once.
The display briefly shows
your selection, then:
4 Select the dial mode:
TONE:
PULSE:
1
2
PSEUDO RING
STOP
5 Press
to exit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Moving your fax and reconnecting
Should it be necessary to move your fax to a new location, first disconnect the
telephone line cord before disconnecting the power lead. When reconnecting,
it is necessary to connect the power lead before connecting the telephone line
cord.
Note:
If your area experiences a high incidence of lightning or power surges, we
recommend that you install surge protectors for the power and telephone
lines. Surge protectors can be purchased from your dealer or at most
electronics shops.
Attach the paper tray and paper tray extension
Attach the paper tray.
Attach the paper tray extension.
Insert
horizontally
and rotate up
Click!
Note: The paper tray extension
has a top side and a bottom
side. If the tabs do not go into
the holes, turn the support over.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper scanning of
documents for transmission. To remove the condensation, turn on the power and
wait approximately two hours before using the machine.
Extension phone (optional)
If desired, you can connect an extension phone to the TEL. SET socket on the
fax.
1 Remove the seal covering the TEL.
SET socket.
TEL.SET
TEL.LINE
2 Connect the extension phone line to
the TEL. SET socket.
TEL.SET
TEL.LINE
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Connecting the cordless handset charger
1 Plug the AC adapter into a standard
230-240 V AC outlet.
Important: Never cover the charger and AC adapter with a blanket, cloth, or
other material. Excessive heating may result and cause fire.
Installing the batteries and charging the cordless handset
♦ Be sure to read the battery precautions on page 5.
1 Insertthebatteriesintothecordless handset, making sure that the “+”
and “-” sides are placed correctly.
+
-
+
-
+
-
2 Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
3 Place the cordless handset in the
charger with the dial pad facing
forward.
• Important! The dial pad must face
forward, or the batteries will not charge.
• The batteries charges automatically
while the cordless handset is in the
charger. While charging, the display
shows:
Charge the
batteries at least 12
hours the first time!
When charging is finished, the battery
icon appears full:
• The cordless handset and charger may
feel warm while charging. This is
normal.
♦ The batteries cannot be overcharged. When not using the cordless
handset, keep it in the charger to ensure that it is always charged.
♦ When the batteries need charging,
will blink in the display and you will
hear beeps during a phone conversation. If you need to continue the
conversation, transfer the call to the fax machine or another cordless
handset (see page 47). Place the cordless handset in the charger and let it
charge.
Note: If the batteries are extremely low, nothing may appear in the display
during the first several minutes that the cordless handset is in the charger.
The battery will begin to charge normally after several minutes.
♦ To ensure that the battery charges properly, wipe the charger contacts
once a month with a cotton swab.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up
Talking range
The talking range of the cordless handset is approximately 200 m (line of
sight; talking range may decrease depending on transmission conditions). If
you hear noise or interference while talking on the cordless handset, move
closer to the fax machine.
Aluminum sash Metal Reinforced concrete
Large metal objects,
metal structures, and
thick walls reduce the
talking range.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Imaging Film
Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images. The print
head in the fax applies heat to the imaging film to transfer ink to the paper.
Follow the steps below to load or replace the film.
♦ The initial starter roll of imaging film included with the machine can print
about 30 A4-size pages.
♦ When replacing the film, use a roll of SHARP FO-9CR imaging film. One
roll can print about 180 A4-size pages.
Important!
If the wrong type of film is loaded, printing will not be possible.
Near end of film detection:
At approximately 3 m from the end of the imaging film (approximately 10
pages can still be printed), “NEAR END OF FILM / REPLACE FILM” will
appear in the display. This alerts you that you will soon need to replace the
film. Correct operation of this function is only guaranteed when SHARP FO-
9CR imaging film is used.
1 Remove the paper from the paper tray
and open the operation panel (press
➊).
2
If you are loading the imaging film for
the first time, go to Step 4.
1
2 Remove the used film and
empty spool.
3 Remove the two green gears from the
spools.
DO NOT DISCARD THE TWO GREEN
GEARS!
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Imaging Film
4 Remove the new roll of imaging film
from its packaging.
• Cut the band that holds the rolls
together.
5 Insert the green gears.
1 slot
Make sure the
gears fit into the
slots in the ends
of the rolls.
2 slots
Fit ends of rolls
onto hubs
6 Insert the film into the print
compartment.
Thick roll
to rear
7 Rotate the front gear as shown until
the film is taut.
8 Close the operation panel (press down
on both sides to make sure it clicks
into place).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
Loading Printing Paper
2
You can load up to 50 sheets of A4-size, 60 - 80 g/m paper in the paper tray
(at room temperature; maximum stack height should not be higher than the
line on the tray).
1 Fan the paper, and then tap the edge
against a flat surface to even the stack.
2 Insert the stack of paper into the tray,
PRINT SIDE DOWN.
• If paper remains in the tray, take it out and combine it into a single stack
with the new paper.
• Be sure to load the paper so that printing takes place on the print side of
the paper. Printing on the reverse side may result in poor print quality.
• GENTLY LOAD THE PAPER IN THE PAPER TRAY.
• DO NOT FORCE THE PAPER DOWN INTO THE FEED SLOT.
The stack should not be
higher than this line.
(This line is the reference
position for the maximum
number of sheets. If sheets
are above this line, press
down with your finger. If the
some sheets remain above
this line after this, please
remove.)
Note: Do not use paper that has already been printed on, or paper that is curled.
Note: If at any time the display shows the
alternating messages at right, check the printing
ADD PAPER &
paper. If the tray is empty, add paper. If there is
paper in the tray, take it out and then reinsert it.
PRESS START KEY
START/MEMORY
When you are finished, press
.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
Print contrast setting
Your fax has been set at the factory to print at normal contrast. If desired, you
can change the print contrast setting to LIGHT.
FUNCTION
Display:
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
twice.
PRINT CONTRAST
1:NORMAL
once.
The display briefly shows
your selection, then:
4 Select the print contrast:
NORMAL: LIGHT:
COPY CUT-OFF
1
2
STOP
5 Press
to return to the date and time display.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
Entering Your Name and Fax Number
Before you begin sending faxes, enter your name and fax (telephone) number
as explained below and set the date and time as explained on page 30.
Once you enter this information, it will automatically appear at the top of each
fax page you send.
STOP
1
4
7
2
5
8
0
3
6
9
FUNCTION
START/MEMORY
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
3 times.
ENTRY MODE
once.
OWN NUMBER SET
ENTER FAX #
once.
4 Enter your fax number by pressing the number keys (max. 20 digits).
• To insert a space between digits, press . To enter a “+”, press
.
• To clear a mistake, press
.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
START/MEMORY
5 Press
to enter the fax number in memory.
6 Enter your name by pressing number keys for each letter as shown in
the chart below. Up to 24 characters can be entered.
Example: SHARP = 7777 44 2 777
7
G =
H =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press
.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
Display:
START/MEMORY
7 Press
DATE&TIME SET
STOP
8 Press
to return to the date and time display.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
Setting the Date and Time
The date and time appear in the display and are printed at the top of every
page you fax. Set the date and time as shown below.
STOP
1
4
7
2
5
8
0
3
6
9
FUNCTION
START/MEMORY
FUNCTION
1 Press
2 Press
3 Press
once and
3 times.
Display:
ENTRY MODE
once and
once.
once.
DATE&TIME SET
The currently set date
appears (example):
DATE 15-02-2003
4 Enter a two-digit number for the day (“01” to “31”).
th
DATE 05-02-2003
Example: the 5
0
5
• To correct a mistake, press
to move the cursor back to the mistake and
then enter the correct number.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
5 Enter a two-digit number for the month (“01” for January, “02” for
February, “12” for December, etc.).
Example: January
DATE 05-01-2003
0
1
6 Enter the year (four digits).
Example: 2004
The currently set time
appears (example):
TIME 12:19
2
0
0
4
7 Enter a two-digit number for the hour (“00” to “23”) and a two-digit
number for the minute (“00” to “59”).
05-JAN 09:25
Example: 9:25
0
9
2
5
START/MEMORY
ANTI JUNK #
8 Press
to start the clock.
STOP
9 Press
to return to the date and time display.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Reception Mode
Setting the Reception Mode
Your fax has four modes for receiving incoming faxes:
FAX mode:
Select this mode when you only want to receive faxes on your line. The fax
machine will automatically answer all calls and receive incoming faxes.
TEL mode:
This mode is the most convenient for receiving phone calls. Faxes can also be
received; however, all calls must first be answered by picking up the fax's
handset or an extension phone connected to the same line.
TEL/FAX mode:
This mode is convenient for receiving both faxes and voice calls. When a call
comes in, the fax will detect whether it is a voice call (including manually
dialled faxes), or an automatically dialled fax. If it is a voice call, the fax will
make a special ringing sound to alert you to answer. If it is an automatically
dialled fax, reception will begin automatically.
A.M. mode:
Select this mode when you go out and want the built-in answering system to
answer all calls. Voice messages will be recorded, and fax messages will be
received automatically.
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then
RECEPTION
press
until the arrow in the display points to the desired mode.
MODE
TEL FAX
RECEPTION
MODE
01-JAN 10:30
01-JAN 10:30
01-JAN 10:30
TEL/FAX A.M.
TEL FAX
TEL/FAX A.M.
TEL FAX
RECEPTION
MODE
1
4
7
2
5
8
0
3
6
9
TEL/FAX A.M.
TEL FAX
01-JAN 10:30
TEL/FAX A.M.
For more information on receiving faxes in FAX, TEL, and TEL/FAX modes,
see Chapter 5, Receiving Faxes. For more information on using A.M. mode,
see Chapter 3, Using the Answering System.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment - Fax Machine
Volume Adjustment - Fax Machine
You can adjust the volume
of the speaker and ringer
using the up and down
arrow keys.
1
4
7
2
5
8
0
3
6
9
Note: To adjust the volume of the cordless handset receiver, see page 36. To
adjust the volume of the cordless handset ringer, see page 50.
Speaker
1 Press
2 Press
.
or
to select the desired volume level.
• Press
again to turn off the speaker.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment - Fax Machine
Fax machine ringer
Display:
1 Press
or
to select the desired
RINGER: HIGH
volume level.
(Make sure
has not been pressed,
RINGER: MIDDLE
RINGER: LOW
and a document is not loaded in the
feeder.)
• The ringer rings once at the selected
level, and then the date and time
reappear in the display.
RINGER: OFF OK ?
2 If you selected “RINGER: OFF OK ?” to
START/MEMORY
turn off the ringer, press
.
Note: When the reception mode is set to TEL, the ringer will still ring at LOW
if turned off.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Using the Cordless Handset
About the Cordless Handset System
Additional cordless handsets
In addition to the cordless handset that is included with the fax machine, up to
five other cordless handsets can used with the fax machine. The additional
cordless handsets must support the DECT/GAP standard.
The FO-D60 base (fax machine) complies with the GAP (Generic Access
Prophile) standard and supports the following functions: Outgoing calls,
incoming calls, intercom. Additional bases and handsets must comply with the
GAP standard.
Note: Due to the wide variety of GAP handsets of different manufacture and
specifications, full functionality with the FO-D60 cannot be guaranteed.
♦ To add a cordless handset, it must be registered in the fax machine. See
page 55.
Additional bases
One cordless handset can be used with up to four bases. By purchasing
additional bases, the range of use of the cordless handset can be expanded.
(Note that once a cordless handset receives a call, it must remain within the
communication range of the base that is transmitting the call.)
♦ A call can only be transferred from a cordless handset to the base that it is
currently using, or to another cordless handset that is using the same base.
♦ To use a cordless handset with additional bases, the cordless handset must
be registered in each of those bases. See page 55.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Making a Phone Call
Making a Phone Call
1 Pick up the cordless handset and press
.
•
appears in the display.
• Note: If the cordless handset display shows BUSY, you must wait until the
fax machine is no longer in use to use the cordless handset.
2 When you hear the dial tone, dial the
number.
3 When you are ready to end the call, press
.
• If the END CALL setting is set to “ON” (see page 53), you can also end the
call by simply placing the cordless handset in the charger.
Cordless handset receiver volume
To adjust the volume of the cordless handset receiver when talking on the
cordless handset, press
or
.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving a Phone Call
You can also dial by entering the phone number first and then pressing
.
♦ Check the number in the display before pressing
. If there is a
mistake, press
digits.
to clear the mistake and then enter the correct
Note: If a pause is needed between any of the digits to access an outside
line or a special service, hold down
until “ ” appears.
Receiving a Phone Call
1 When the cordless handset rings, pick it up and press
Talk to the other party.
to answer.
2 When you are ready to end the call, press
.
• If the END CALL setting is set to “ON” (see page 53), you can also end the
call by simply placing the cordless handset in the charger. (The call will end
even if it has been placed on hold.)
Putting a Call on Hold
To put the other party on hold during a call, press
. While the call is on
hold, “C” will blink in the display. When you are ready to resume the call,
press once again.
♦ If the END CALL setting is set to “ON” (see page 53), placing the cordless
handset in the charger will end the call, even if the call is on hold.
♦ If the END CALL setting is set to “OFF”, placing the cordless handset in the
charger will not break the connection while a call is on hold, and thus phone
charges may continue to apply.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving a Fax Using the Cordless Handset
Receiving a Fax Using the Cordless Handset
If you hear a fax tone after answering a call on the cordless handset, or if the
other party speaks to you and then wants to send a fax, press
signals the fax machine to begin fax reception.
. This
Press to begin
fax reception
Note: If the fax machine detects a fax signal after you answer a call on the
cordless handset, it will begin reception automatically.
Storing and Using Auto-Dial Numbers
You can store your most frequently dialed numbers for automatic dialling.
Numbers can be stored in the cordless handset or in the fax machine. To store
a number in the cordless handset, follow the steps below.
♦ Up to 20 numbers can be stored in the “phone book” in the cordless
handset. Numbers stored in the cordless handset can only used by the
cordless handset.
♦ To store a number in the fax machine, see page 87. The cordless handset
can also use numbers that are stored in the fax machine.
Cordless handset display:
1 Press
2 Press
.
1 PHONE BK
.
11 NEW
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing and Using Auto-Dial Numbers
NAME?
3 Press
.
4 Enter a name for the auto-dial number. To enter each letter, hold down
the key for the letter as shown in the chart below until the letter appears
in the display. Up to 8 characters can be entered. (If you do not wish to
enter a name, go directly to Step 5.)
SPACE, PAUSE ( ), - =
A, B, C =
M, N, O =
P, Q, R, S =
T, U, V =
# ( ), ?, _ =
D, E, F =
W, X, Y, Z =
=
G, H, I =
J, K, L =
♦
To clear a mistake, press
.
To clear all the entered letters, hold down
NUMBER?
.
5 Press
.
6 Enter the number by pressing the number keys. Up to 24 digits can be
entered. (Note: A space cannot be entered.)
•
To clear a mistake, press
.
To clear all the entered numbers, hold down
.
• If a pause is needed between any of the digits to access an outside line or
a special service, hold down
be entered in a row.
until “ ” appears. Several pauses can
DONE
7 Press
.
8 Return to Step 2 to store another number, or press
exit.
repeatedly to
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing and Using Auto-Dial Numbers
Dialling an auto-dial number
1 Press
2 Press
once.
or
until the auto-dial number that you wish to dial
appears in the display (the name will appear, or the number if no name
was stored).
• To go directly to names that begin with a certain letter, hold down the
number key with that letter until the letter appears in the display, and then
press
until the desired name appears.
• To check the number of a name in the display, press
.
• If you wish to dial an auto-dial number that is stored in the fax machine,
press until BASE appears in the display, press , and then press
or until the desired number appears. (Note that an auto-dial
number in the fax machine that includes an “R” will not appear.)
3 Press
.
• The number is automatically dialed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing and Using Auto-Dial Numbers
Quick Search
You can also quickly dial an auto dial number by entering the first 3 letters of
the name.
1 Enter the first 3 letters of the name of the auto dial number that you wish
to dial. To enter each letter, hold down the number key with the desired
letter until the letter appears in the display.
• If you do not wish to enter all 3 letters, you can press
and then enter
or
one letter. (If a different name appears in the display, press
until the desired name appears.)
2 The name of the auto-dial number that begins with those 3 letters
appears. (If there is no name that begins with those letters, the closest
name will appear).
• If the correct name does not appear, press
or
until it appears.
3 Press
.
• The number is automatically dialed.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing and Using Auto-Dial Numbers
Editing an auto-dial number
If you need to make changes to a previously stored auto-dial number, follow
these steps:
Cordless handset display:
1 Press
.
1 PHONE BK
12 EDIT
2 Press
3 Press
and then
.
.
• The name of one of your stored auto-dial numbers appears.
4 Press
or
until the name of the number that you wish to edit
appears in the display.
5 Press
.
6 Edit the name.
• Press
to delete letters (hold down
the number keys to enter new letters (see Step 4 on page 39).
to delete all the letters). Press
• If you do not wish to change the name, go directly to Step 7.
7 Press
.
8 Edit the number.
• Press
to delete digits (hold down
number keys to enter new digits.
to delete all digits). Press the
• If a pause is required between any of the digits to access a special service
or an outside line, hold down until “ ” appears.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing and Using Auto-Dial Numbers
• If you do not wish to change the number, go directly to Step 9.
DONE
9 Press
.
10 Press
repeatedly to exit.
Deleting an auto-dial number
If you need to delete an auto-dial number, follow these steps:
Cordless handset display:
1 Press
.
1 PHONE BK
13 DELETE
2 Press
3 Press
and then
.
.
• The name of one of your stored auto-dial numbers appears.
4 Press
or
until the number that you wish to delete appears in
the display.
5 Press
6 Press
.
DONE
repeatedly to exit.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Dialling From the Incoming/Outgoing Call List (Redial)
Dialling From the Incoming/Outgoing Call
List (Redial)
The cordless handset keeps a list of the most recent calls that you have made
and received on the cordless handset. You can view this list and automatically
dial a number in the list.
♦ Important: Received calls only appear in the list if you subscribe to a Caller
ID service and have activated the Caller ID function (see page 107).
♦ If you subscribe to a Caller ID service and have activated the Caller ID
function, you can also view the Caller ID list that is kept in the fax machine.
(This list shows the most recent 30 calls received by the fax machine; see
page 109.)
1 To view the incoming/outgoing call list in the cordless handset, press
(do not hold
down). (Note: You can also hold down
until the first number in the list appears in the display.)
To view the Caller ID list in the fax machine, hold down
“CALLS” (and then a name) appears in the display.
until
2 Press
or
until the name that you wish to call appears.
or to check
• If you are viewing the Caller ID list, you can press
the number of a name that appears in the display. To check the time of the
call, press
.
3 Press
. The number is automatically dialed.
• To exit the list without calling a number, press
repeatedly.
Note: If the Caller ID information consists of only the name and not the
number of the caller, the call will not appear in the cordless handset display.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Intercom Feature
Deleting all calls from the incoming/outgoing list
To delete all calls from the incoming/outgoing list in the cordless handset, follow
the steps below. (To erase all calls from the Caller ID list, see page 110.)
Cordless handset display:
1 Press
twice.
2 CALLS
21 DELETE
2 Press
3 Press
once.
to delete the calls.
• To cancel, press
.
4 Press
to repeatedly to exit.
Using the Intercom Feature
You can use the fax machine and cordless handsets as an intercom system.
♦ It may not be possible to page another cordless handset or the fax machine
when other cordless handsets or the fax machine are already in use.
Paging the fax machine or another cordless handset from a
cordless handset
Cordless handset display
(example of paging the
1 Enter the number (1 to 6) of the
fax machine)
cordless handset that you wish to
0
page, or press
to page all
cordless handsets.
To page the fax machine, press
.
• If the number of the cordless handset or fax machine (0 to 6) is stored in the
cordless handset’s phonebook with a name, the name will appear when
you enter the number.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Intercom Feature
2 Press
.
•
appears in the display.
3 The paged device rings and the other person answers.
4 Talk with the other person. When you are ready to end the conversation,
press
.
Paging a cordless handset from the fax machine
(cordless handset locator)
You can use this procedure to page a cordless handset, or locate a handset in
the event that you misplace it.
1 Pick up the fax machine handset.
Fax machine display:
2 Press INTERCOM on the fax machine, and
INTERCOM
enter the number of the cordless
handset that you wish to page. (Press
3
to page all cordless handsets.)
Example:
3
3 The selected cordless handset rings.
• This allows you to locate the cordless handset if you have misplaced it.
4 The other person presses
on the cordless handset to answer.
5 Talk with the other person. When you are ready to end the conversation,
replace the handset.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring Calls
If a call comes in while the Intercom feature is being used
If an outside call comes in while you are using the Intercom feature, the
person who wishes to take the call should first stop the Intercom call (press
on the cordless handset or replace the fax machine handset), and then
answer the outside call (press
machine handset).
on the cordless handset or pick up the fax
Transferring Calls
You can transfer a call to the fax machine or to a cordless handset.
Transferring a call from a cordless handset to the fax
machine
Note: It is not possible to talk with the person who answers on the fax
machine before transferring a call.
1 During the call, press
hold).
on the cordless handset (the call is put on
2 Press
to transfer the call to the fax machine.
• To cancel the transfer and return to the initial caller, press
.
3 Press
.
• When the transfer is complete, the display will return to the standby display.
• If nobody answers within 30 seconds, all cordless handset will start ringing.
If nobody answers within the next 30 seconds, the call will be disconnected.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring Calls
Transferring a call from a cordless handset to another
cordless handset
1 During the call, press
hold).
on the cordless handset (the call is put on
2 Enter the number of the handset, or press
to page all cordless
handsets (this does not include the fax machine).
• To cancel the transfer and return to the initial caller, press
.
3 Press
• You can speak to the person who answers on the cordless phone. When
finished, press to complete the transfer.
.
• To complete the transfer without speaking to the person who answers,
press
.
• If nobody answers, press
to return to the initial caller.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring Calls
Transferring a call from the fax machine to a cordless
handset
Note: A call can only be transferred once.
Fax machine display:
PRESS HANDSET #
1 During the call, press INTERCOM on the
fax machine.
• The numbers of cordless handsets that
are registered in the fax machine will
appear.
1
2
3
4
5
6
Fax machine display:
CALL TRANSFER
2 Enter the number of the cordless
handset to which you wish to transfer
the call. (Press
to page all
cordless handsets.)
3
Example:
3
3 The selected cordless handset rings and the other person answers.
Replace the fax machine handset to complete the transfer.
• Note: You will not be able to hear the sound of the cordless handset ringing
through the fax machine handset.
• If nobody answers, press INTERCOM or
to return to the initial caller.
STOP
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Ringing Melody and Volume
Adjusting the Ringing Melody and Volume
You can select one of six ringing melodies for the cordless handset, as well as
adjust the ringer volume or turn it off.
Selecting a ringing melody
Cordless handset display:
1 Press
3 times.
3 RING
2 Press
3 Press
once.
once.
31 MELODY
1
4 Enter the number (from 1 to 6) of the
desired melody (or press or
until the desired number appears and
press ).
DONE
• The selected melody will sound. To
select a different melody, repeat steps 3
and 4.
5 Press
repeatedly to exit.
Adjusting the ringer volume
Cordless handset display:
3 RING
1 Press
3 times.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Ringing Melody and Volume
32 VOLUME
2 Press
once and then
once.
once.
3
3 Press
4 Press
DONE
or
to select a volume
level from 1 to 4 and then press
.
(You can also simply enter the number
of the desired volume level.)
5 Press
repeatedly to exit.
Turning off the cordless handset ringer
If you do not wish the cordless handset to ring when a call is received (or to
sound a beep when a key is pressed), follow these steps to turn the ringer off.
When this is done,
will appear in the display.
Cordless handset display:
3 RING
1 Press
3 times.
33 SILENT
2 Press
3 Press
4 Press
once and then
once.
twice.
OFF
DONE
or
to select ON or OFF
.
and then press
5 Press
repeatedly to exit.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Features
Turning beep sounds on and off
A beep normally sounds when you press a key on the cordless handset. To
turn the beep sounds on or off, follow these steps.
Cordless handset display:
1 Press
3 times.
3 RING
2 Press
3 Press
4 Press
once and then
once.
once.
34 BEEPS
ON
or
to select ON or OFF
.
DONE
and then press
5 Press
repeatedly to exit.
Other Features
Call time
To check the duration of your most recent call, follow these steps:
Cordless handset display:
1 Press
2 Press
twice.
2 CALLS
22 TIME
once and then
once.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Features
3 Press
4 Press
once. The duration appears.
repeatedly to exit.
End call setting
When this setting is turned on, calls can be ended by simply replacing the
handset in the charger (there is no need to press
if it has been placed on hold.)
). (A call will end even
Cordless handset display:
4 SET
1 Press
3 times.
once.
41 END CALL
2 Press
3 Press
4 Press
once.
DONE
or
to select ON or OFF
and then press
.
5 Press
repeatedly to exit.
Turning the cordless handset power on and off
To conserve battery power, you can turn the cordless handset off. To turn off
the power, hold down
until the display goes blank. To turn the power on,
hold down until the display turns on. The power also turns on
automatically when the cordless handset is placed in the charger.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Features
Listening to messages from the cordless handset
When new messages have been received in the fax machine’s answering
system,
will appear in the display. To listen to the messages from your
cordless handset, follow the steps below.
♦
changes to
after you listen to the messages.
Cordless handset display:
1 Press
once.
6 ANSWER
2 Press
3 Press
once.
ANSWER
to play all messages in the answering system, or
to
play only new messages.
• To repeat a message, press
.
• To skip a message, press
• To delete a message, press
• To stop playback, press
.
while the message is playing.
.
4 When finished, press
repeatedly to exit.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
Registering Cordless Handsets
In order to be used, a cordless handset must first be registered in the fax
machine. The cordless handset that came with the fax machine is already
registered. To register an additional cordless handset, follow the steps in
Automatic registration or Custom registration on the following pages.
♦ Use automatic registration when you are only registering the cordless
handset in one fax machine and the system PIN number has not been
changed from its initial setting (0000) (see page 57). This is the easiest
method of registration and does not require entering the System PIN
number.
♦ Use custom registration when the system PIN number has been changed
to a number other than 0000. The system PIN number must be entered
during registration.
♦ A cordless handset can be registered in up to four fax machines. To register
the cordless handset in multiple fax machines, repeat the custom
registration procedure using each fax machine. To select which fax machine
the cordless handset will normally be used with, see page 60.
Automatic registration
Use automatic registration when you are only registering the cordless handset
in one fax machine and the system PIN number has not been changed from
its initial setting (0000).
On the fax machine
Fax machine display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
DECT SETTING
HS ENTRY
once.
PRESS START KEY
WAITING HS ENTRY
once.
START/MEMORY
4 Press
.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
On the cordless handset
5 Press
repeatedly until the display
5 BASE
at right appears.
The cordless handset
display changes as
follows each time you
6 On the cordless handset, press
3 times.
press
:
51 REGIST
AUTO
Fax machine display:
HS 2 REGISTERED
7 When registration is finished, the fax
machine and cordless handset will
show the messages at right. Note the
number that is assigned to the
cordless handset (“2” is shown as an
example).
Cordless handset display:
REGIST
STOP
2
Press
exit.
on the fax machine to
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
Programming a system PIN
The system PIN is a 4-digit ID number that is used to prevent unauthorized
registration of a cordless handset in a fax machine. When the system PIN is
set to a number other than 0000 (the initial factory setting), a cordless handset
must be registered using custom registration and the correct system PIN must
be entered on the cordless handset during registration. Follow these steps to
program a system PIN in the fax machine.
♦ To prevent other people from adding cordless handsets without your
authorization, it is recommend that you change the system PIN to a number
other than 0000. (Note that a cordless handset can be deleted without
entering the system PIN.)
Fax machine display:
FUNCTION
1 On the fax machine, press
once
DECT SETTING
and
once.
SYSTEM PIN
2 Press
3 Press
once and
once.
once.
OLD PASSWORD
4 Enter the current system PIN (4 digits).
• The system PIN is initially set to 0000 at the factory.
• To clear a mistake, press
.
START/MEMORY
5 Press
.
6 Enter the new system PIN that you wish to program (4 digits).
START/MEMORY
7 Press
.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
8 Enter the new system PIN once again for confirmation.
START/MEMORY
9 Press
.
STOP
10 Press
to return to the date and time display.
Custom registration
Use this procedure to register a cordless handset when the system PIN in the
fax machine has been set to other than 0000, or when you are registering the
cordless handset in multiple fax machines..
On the fax machine
Fax machine display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
DECT SETTING
HS ENTRY
once.
PRESS START KEY
WAITING HS ENTRY
once.
START/MEMORY
4 Press
.
On the cordless handset
Cordless handset display:
5 BASE
5 Press
repeatedly until the display
at right appears.
6 Press
once.
51 REGIST
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
7 Press
8 Press
once and
once.
CUSTOM
CODE ?
once and then enter the
number (1 to 4) that you would like to
assign to the fax machine. (This
number is used to identify the fax
machine when the cordless handset is
registered in multiple fax machines.)
9 Enter the 4-digit system PIN number that is programmed in the fax
machine.
10 Press
.
REGIST
1
2
3
4
5
6
11 Enter the number that you would like
to assign to the cordless handset.
Fax machine display:
HS 2 REGISTERED
12 When registration is finished, the fax
machine and cordless handset will
show the messages at right (the
handset number “2” is shown as an
example).
Cordless handset display:
REGIST
STOP
Press
on the fax machine and
2
on the cordless handset to exit.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
Giving priority to a base
When a cordless handset is registered with multiple bases, use the following
setting to select which base the cordless handset will normally be used with.
♦ The initial setting is NONE. When NONE is selected (or when the selected
base is not powered on), the cordless handset will be used with the first
base that is powered on.
Cordless handset display:
1 On the cordless handset, press
5 BASE
repeatedly until the display at right
appears.
2 Press
once and
once.
52 PRIOR
3 Press
once.
• NONE or the number of the currently selected fax machine appears in the
display.
4 Enter the number (1 to 4) of the base to be given priority. (The number is
the number that was assigned to the base during custom registration of
the cordless handset.)
To select NONE, press
.
(Entering a number that has not been assigned will have no effect.)
5 Press repeatedly
to exit.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
Cordless handset display language
Use this setting to select the language used in the cordless handset display.
♦ This setting is selected on the fax machine.
Fax machine display:
FUNCTION
1 On the fax machine, press
once
DECT SETTING
and
once.
HS LANGUAGE
2 Press
3 Press
4 Press
once and
twice.
once.
or
until the desired language appears in the display.
START/MEMORY
5 Press
6 Press
.
STOP
to return to the date and time display.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Cordless Handsets
Deleting a cordless handset
Follow these steps if you need to delete a cordless handset (cancel the
registration in the fax machine).
Fax machine display:
FUNCTION
1 On the fax machine, press
once
DECT SETTING
and
once.
HS DELETE
2 Press
3 Press
once and
once.
PRESS HANDSET #
once.
1
2
3
4
5
6
4 Enter the number of the cordless handset that you wish to delete.
START/MEMORY
5 Press
6 Press
.
STOP
to return to the date and time display.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using the Answering System
The built-in answering system allows you to receive both voice messages and
faxes while you are out.
♦ To use the answering system, you will first need to record an outgoing
message. When you go out, turn on the answering system by setting the
reception mode to A.M.
Recording an Outgoing Message
The outgoing message (OGM) is the greeting that the machine plays after
answering a call to inform callers that they can leave a message or send a fax.
Follow the steps below to record a message.
Example:
“Hello. You've reached ______ . No one is available to take your call right now.
Please leave a message after the beep or press your facsimile Start key to
send a fax. Thank you for calling.”
Display:
REC/
1 Press
2 Press
once and
once.
MEMO
OGM1(GENERAL)
LIFT HANDSET OR
once.
PLAY: PLAYBACK
3 Lift the handset.
(If you have already recorded a
PLAY/
message, you can press
to
HOLD
listen to the message.)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Answering System
START/MEMORY
4 Press
and speak into the handset to record a message.
• The outgoing message can be up to 60 seconds long. While recording, the
display will show the time left to record.
STOP
5 When finished, replace the handset or press
.
To listen to the outgoing message
To listen to the outgoing message, follow Steps 1 and 2 of the above
PLAY/
procedure and then press
. Note that the general outgoing message
HOLD
cannot be erased. If you need to change it, simply repeat the recording
procedure.
Operating the Answering System
Activating the answering system
To turn on the answering system so that callers can leave messages, press
RECEPTION
until the arrow in the display points to A.M.
MODE
RECEPTION
MODE
TEL FAX
TEL/FAX A.M.
♦ The outgoing message will play (you can stop playback by pressing
STOP
).
♦ It will not be possible to set the reception mode to A.M. if an outgoing
message has not been recorded.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Answering System
Note: In A.M. mode, the machine will automatically switch to fax reception if it
detects six seconds of silence after answering a call. For this reason, if a
caller pauses for this length of time while leaving a message, they will be cut
off.
Number of rings in A.M. mode (Toll Saver function)
The number of rings on which the machine answers incoming calls in A.M.
mode depends on whether the Toll Saver function is turned on, and if it is on,
whether you have messages.
♦ The Toll Saver function is initially turned on.
ON
OFF
Toll Saver
Toll Saver
No received messages
Received messages
Hello!
NOTHING
4 Rings
Hi!
Hi!
(Answer according to
NUMBER OF RINGS setting)
2 Rings
Ring
Ring
Ring
Ring
Ring
Ring
Ring
Ring
Ring
Ring
To adjust the NUMBER
OF RINGS setting, see
page 98.
To turn off the Toll Saver
function, see page 74.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Answering System
Listening to received messages
When you return, the display will show the number of messages recorded.
Follow the steps below to listen to your messages.
PLAY/
1 Press
.
HOLD
• If you only want to listen to new messages (messages not previously
PLAY/
listened to), continue to hold
down for at least two seconds.
HOLD
2 The messages will play.
• As each message plays, the date and time of recording will appear briefly in
the display. If no messages were received, NO MESSAGES will appear.
• Repeat: To listen to a message a second time, press
before
REPEAT
playback of that message ends. To move back to the previous message,
press
within 3 seconds of the beginning of the current message.
REPEAT
0
SKIP
• Skip: To skip forward to the next message, press
.
STOP
Note: Playback will stop if you receive a call, lift the handset, or press
.
♦ You can also listen to the messages from the cordless handset. See page
54.
♦ You can print out a list of your received messages that shows the date and
time that each was received. See page 115.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Answering System
Erasing received messages
It is important to erase received messages after you listen to them to ensure
that the memory does not become full.
FUNCTION
♦ Erasing all messages: To erase all messages, press
,
, and
DELETE
START/MEMORY
then
.
♦ Erasing a single message: To erase a single message, press
DELETE
while the message is being played.
Recording memos
You can record memos for yourself and other users of the machine. These will
PLAY/
be played back together with incoming messages when the
pressed.
key is
HOLD
REC/
1 Press
once and
once.
MEMO
2 Pick up the handset, press START/MEMORY , and speak into the handset.
STOP
3 When you have finished speaking, replace the handset or press
.
Recording phone conversations (2-way recording)
REC/
To record a phone conversation, hold down the
key during the
MEMO
conversation you wish to record. When you are finished, release the key. The
PLAY/
conversation will be played back when the
key is pressed.
HOLD
Note: Intercom conversations cannot be recorded.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Answering System Settings
Optional Answering System Settings
Setting ICM time
Incoming messages (ICMs) are the messages which callers leave for you on
the built-in answering system. The answering system is set at the factory to
allow each caller a maximum of 4 minutes to leave a message. If desired, you
can change this setting to 15, 30, or 60 seconds.
Display:
FUNCTION
1 Press
once and
once.
A.M. SETTING
RECORDING TIME
2 Press
3 Press
once and
once.
.
4 Press a number from 1 to 4 to select the desired ICM recording time.
1
3
15 seconds
60 seconds
4
30 seconds
4 minutes
2
The display briefly shows
your selection, then:
REMOTE CODE
STOP
5 Press
to return to the date and time display.
FAX mode on A.M. failure
If the memory for recording incoming messages becomes full while you are
out, the answering system will no longer be able to record messages. The ON
A.M. FAILURE setting is used to choose the response of the machine to
incoming calls when this happens:
♦ YES (switch to FAX mode): The reception mode will switch to FAX mode,
allowing the machine to continue to receive faxes automatically. With this
setting, you can still use the remote commands to listen to your messages
and then erase them (see Remote Operations on page 74).
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Answering System Settings
♦ NO (do not switch to FAX mode): The machine will answer after 20 rings,
after which it will wait to receive a remote command. Most callers will hang
up before it answers; however, when you call the machine from a remote
location, you can wait until it answers, listen to your messages, and then
erase them (see Remote Operations on page 74).
The initial setting is NO . If you want to change the setting to YES, press the
panel keys as follows:
Display:
FUNCTION
1 Press
once and
once.
A.M. SETTING
ON A.M. FAILURE
1=YES, 2=NO
2 Press
3 Press
once and
twice.
.
The display briefly shows
your selection, then:
4 Press
to select YES (switch to
1
OGM ONLY MODE
FAX mode), or
to select NO.
2
STOP
5 Press
to return to the date and time display.
OGM only mode
If needed, you can turn off recording of incoming messages. In this case, your
outgoing message will play, but callers will not be able to leave a message.
(The machine will still receive faxes sent by automatic dialling.)
Display:
FUNCTION
1 Press
2 Press
once and
once.
A.M. SETTING
OGM ONLY MODE
once and
once.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer Function
3 Press
4 Press
.
1=YES, 2=NO
The display briefly shows
your selection, then:
to turn on OGM only mode,
1
TOLL SAVER
or
to turn it off.
2
STOP
5 Press
to return to the date and time display.
Transfer Function
The Transfer function is used to have the machine automatically call you at a
specified number every time it receives an incoming message. This lets you
hear your messages immediately after they come in, even when you are at a
remote location.
To use the Transfer function, you must first program the number that you wish
the machine to call (the transfer number), and record the transfer message
that plays when you answer the phone at the remote location.
When you go out and wish to use the transfer function, turn it on. When you
return and no longer wish to use the transfer function, turn it off.
Programming the transfer number
To use the Transfer function, you must first give the machine the number to
call (the transfer number).
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
A.M. SETTING
once and
3 times.
TRANSFER TEL #
ENTER TEL #
.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer Function
4 Press the number keys to enter the transfer number.
FUNCTION
• To insert a pause between any two digits of the number, press
.
START/MEMORY
5 Press
.
STOP
6 Press
to return to the date and time display.
Recording the transfer message
The transfer message plays when you answer the telephone, and informs you
that the call is a transfer call. It can be up to 15 seconds long. To record a
transfer message, follow the steps below. The following is an example:
“Hello. This is a transfer call for (YOUR NAME). Enter your remote code
number now.”
Display:
REC/
1 Press
2 Press
once and
twice.
MEMO
OGM2(TRANSFER)
once.
3 Lift the handset.
(If you have already recorded a
PLAY/
message, you can press
to
HOLD
listen to the message, or press
to delete the message.)
DELETE
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer Function
START/MEMORY
4 Press
and speak into the handset to record the message.
• The transfer message can be up to 15 seconds long. While recording, the
display will show the time left to record.
STOP
5 When finished, replace the handset or press
.
Checking or erasing the transfer message
To check or erase the transfer message, follow Steps 1 and 2 of the above
PLAY/
procedure, and then press
erase the message.
to check the message, or
to
HOLD
DELETE
Turning the Transfer function on and off
When you go out and wish to use the Transfer function, turn it on as follows:
Display:
FUNCTION
1 Press
once and
once.
A.M. SETTING
2 Press
3 Press
once and
3 times.
TRANSFER FUNC
1=YES, 2=NO
.
The display briefly shows
your selection, then:
4 Press
to turn on the Transfer
to turn the function off.)
1
function.
ON A.M. FAILURE
(Press
2
STOP
5 Press
to return to the date and time display.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer Function
6 Each time the machine receives an incoming message, it will call your
programmed transfer number. When you answer, you will hear your
recorded message telling you that the call is a transfer call. On the dial
pad of your phone, enter
, your remote code number (see page 74),
and . The machine will play back your messages.
• You can also perform any of the remote operations described in Remote
Operations later in this chapter (see page 74).
Note: When you hang up after a transfer call, the machine will not
immediately resume normal operation. If you want the machine to accept calls
immediately after a transfer call, enter
want to hang up during message playback, first enter
playback, then enter twice).
twice before hanging up (if you
and to stop
0
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
Remote Operations
When you are out, you can call the machine from any tone dial telephone and
play back your messages using the remote commands. You can also use
these commands to change the reception mode and other settings.
Remote code number
To access the machine to perform remote operations, you must first enter your
remote code number. The remote code number has been set to "001" at the
factory. If you wish to use a different number, follow these steps:
Display:
FUNCTION
1 Press
once and
once.
A.M. SETTING
REMOTE CODE
2 Press
3 Press
once and
twice.
.
4 Press the number keys to enter a 3-digit remote code number.
START/MEMORY
STOP
5 Press
to store the remote number, and then
to return
to the date and time display.
Toll Saver
When you call the machine to listen to your messages, it will answer after two
rings if it has received at least one message, or after four rings if it has not
received any messages.
This allows you to save money on telephone charges, particularly if you are
calling long distance. If the machine does not answer after the second ring,
you can simply hang up before it answers, saving yourself the cost of that call.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
If you do not want to use the Toll Saver function, you can turn it off by following
the steps below. In this case, the machine will answer after the number of
rings set with the NUMBER OF RINGS setting (see Changing the number of
rings on page 98).
Display:
FUNCTION
1 Press
once and
once.
A.M. SETTING
TOLL SAVER
1=YES, 2=NO
2 Press
3 Press
once.
once.
The display briefly shows
your selection, then:
4 Press
to turn on the Toll Saver
to turn it off.
1
RECORDINGTIME
function, or
2
STOP
5 Press
to return to the date and time display.
Retrieving your messages
1 Call the machine from a tone dial telephone. When your outgoing
message begins, press
on the telephone.
• You will hear a short beep, and the outgoing message will stop.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
2 Enter your remote code number and then press
.
• You will hear a series of beeps equal to the number of messages recorded,
or one long beep if four or more messages have been received. The
machine will then play back the messages, beeping once at the end of each
message. When all messages have been played back, you will hear a long
beep.
• If no messages have been received, you will hear a short beep. You can
either hang up, or perform any of the operations described in the following
section, Other remote operations.
3 While the messages are playing, you can do any of the following:
• Repeat: To listen to a message a second time, press
and
on the
2
telephone before that message ends. To move back to the previous
message, press
message.
and
during the first 3 seconds of the current
2
• Skip forward: To skip forward to the next message, press
and
5
on the telephone.
• Stop: To stop playback, press
and
on the telephone. After this,
0
you can enter any of the commands described in the following section,
Other remote operations.
• Play new messages: To listen to only your new messages, first stop
playback by pressing
and
, and then press
and
.
0
6
• Erase a message: To erase the message you are currently listening to,
press and before it ends.
3
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
4 When you have finished listening to your messages, you can do any of
the following:
• Erase all messages: Press
,
, and
.
.
3
3
• Repeat playback: Press
and
7
• Perform other operations: You can enter any of the commands described
in the following section, Other remote operations.
• Hang up: If you do not erase your messages first, they will be saved and
any new messages will be recorded after them. If you want the machine to
resume normal operation immediately, press
twice before hanging up
(in some cases, particularly when the Transfer function is used, the
machine may not accept new calls for one or two minutes after you hang up
unless you press
twice).
Note: You can also call the machine and perform remote operations when the
reception mode is set to FAX. In this case, when you call the machine, press
immediately after it answers (before you hear the fax tone), and then
continue from Step 2 above.
Comments:
♦ When a remote command is accepted by the machine, you will hear one
beep. If an incorrect command is entered, you will hear four beeps. In the
latter case, re-enter the correct command.
♦ When entering a command, do not pause longer than 10 seconds between
each digit. If you do, you will hear a 4-beep error signal and the digits
entered up to that point will be cleared. In this case, re-enter the command
from the beginning.
♦ If you pause for longer than 10 seconds before entering a command, or
make two errors while entering your remote code number, the line will be
disconnected. (This prevents unauthorized people from attempting to
guess your remote code number.)
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
Other remote operations
After listening to your messages, you can perform any of the following
operations by pressing the appropriate keys on the telephone.
Note: The following commands cannot be entered while messages are being
played back. If you do not want to wait until playback ends to enter a
command, first stop playback by pressing
command.
and
, and then enter the
0
Changing the fax reception mode
Select a new reception mode by pressing the keys as follows:
♦ A.M. mode:
♦ FAX mode:
♦ TEL mode:
,
, and
, and
, and
.
8
1
,
.
8
2
,
.
8
3
Caution: If you select TEL mode, you will not be able to change the
reception mode again.
♦ TEL/FAX mode:
,
, and
.
8
4
Recording a new outgoing message
1 Press
and
on the telephone.
4
2 When you hear a short beep, speak into the telephone to record the new
message.
• The message can be up to 15 seconds long. After 15 seconds (or earlier if
the machine detects silence after you finish speaking), you will hear a beep,
and the new message will be played back.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
Turning the Transfer function on or off
To turn Transfer on: Press
,
,
, and
, and
on the telephone.
9
9
1
2
To turn Transfer off: Press
on the telephone.
Changing the transfer telephone number
1 Press
,
, and
on the telephone.
9
0
2 After you hear a short beep, enter the new telephone number. When
finished, press
.
• To insert a pause between any two digits of the number, press
.
Recording a new transfer message
1 Press
,
, and
on the telephone.
9
3
2 When you hear a short beep, speak into the telephone to record the new
message.
• The time for the transfer message is fixed at 15 seconds. After 15 seconds
(or earlier if the machine detects silence after you finish speaking), you will
hear a beep, and the new message will be played back automatically.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Operations
Recording a memo
You can record a memo for yourself or other users of the machine. The memo
will be played back when incoming messages are listened to.
1 Press
and
on the telephone.
2 When you hear a short beep, speak into the telephone to record the
memo.
3 When you are finished, press
and
on the telephone.
0
• If the machine detects silence, it will stop recording automatically.
OGM only mode
To turn on OGM only mode: Press
,
, and
on the telephone.
1
1
(Your outgoing message will play, but callers will not be able to record a
message. Faxes sent by automatic dialling will be received)
To turn off OGM only mode: Press
,
, and
on the telephone.
1
2
80
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Sending Faxes
Transmittable Documents
Size and weight
The size and weight of documents that you can load in the document feeder
depend on whether you load one page at a time or several pages at once.
Loading one page at a time:
Loading up to 10 pages at once:
Minimum size
Minimum size
Maximum size
Maximum size
210 mm
210 mm
148 mm
148 mm
140 mm
140 mm
297 mm
600 mm
Minimum weight Maximum weight
Minimum weight Maximum weight
52 g/m²
157 g/m²
80 g/m²
52 g/m²
Note: Letters or graphics on the edges of a document will not be scanned.
5 mm
Letters in the
shaded area will
not be scanned.
5 mm
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Document
Other restrictions
♦ The scanner cannot recognise yellow, greenish yellow, or light blue ink.
♦ Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.
♦ All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.
♦ Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slippery coated surface should
be photocopied, and the copy loaded in the feeder.
Loading the Document
Up to 10 pages can be placed in the feeder at one time. The pages will
automatically feed into the machine starting from the bottom page.
♦ If you need to send or copy more than 10 pages, place the additional pages
gently and carefully in the feeder just before the last page is scanned. Do
not try to force them in, as this may cause double-feeding or jamming.
♦ If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the feeder as the previous page
is being scanned. Insert gently to prevent double-feeding.
1 Adjust the document guides to the
width of your document.
2 Insert the document face down in the
document feeder. The top edge of the
document should enter the feeder first.
• READY TO SEND will appear in the
display.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
3 Adjust the resolution and/or contrast settings as explained in
Resolution and Contrast below, then dial the receiving machine as
explained on page 85.
Adjusting the Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a
document.
♦ The default resolution setting is STANDARD and the default contrast setting
is AUTO.
♦ You must adjust the settings each time you don’t want to use the default
settings.
Note: The resolution and contrast settings are only effective for sending a
document. They are not effective for receiving a document.
Resolution settings
STANDARD
Use STANDARD for ordinary documents. This
setting gives you the fastest and most
economical transmission.
FINE
Use FINE for documents containing small letters
or fine drawings.
SUPER FINE
HALF TONE
Use SUPER FINE for documents containing
very small letters or very fine drawings.
Use HALF TONE for photographs and
illustrations. The original will be reproduced in
64 shades of gray.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
Contrast settings
AUTO
DARK
Use AUTO for normal documents.
Use DARK for faint documents.
1 Load the document(s).
• The document must be loaded before
the resolution and contrast can be
adjusted.
RESOLUTION
Display:
2 Press
one or more times until
the desired resolution and contrast
settings appear in the display.
STANDARD :AUTO
• The first time you move through the list
of resolution settings, the contrast
setting AUTO will appear next to each
resolution setting. The second time you
move through the list, the contrast
setting DARK will appear.
FINE
:AUTO
SUPER FINE :AUTO
HALF TONE :AUTO
STANDARD :DARK
HALF TONE :DARK
Note: In order to transmit in SUPER FINE resolution, the receiving fax machine
must also have that resolution. If it doesn’t, your machine will automatically step
down to the next best available setting.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Normal Dialling
Sending a Fax by Normal Dialling
With Normal Dialling, you pick up the handset (or press
pressing the number keys.
) and dial by
♦ If a person answers, you can talk with them through the handset before
sending the fax. (If you pressed
talk.)
, you must pick up the handset to
♦ Normal Dialling allows you to listen to the line and make sure the other fax
machine is responding.
1 Load the document(s).
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Pick up the handset or press
Listen for the dial tone.
.
or
ABC
JKL
TUV
DEF
3 Dial the number of the receiving
1
4
2
5
8
3
6
machine by pressing the number keys.
GHI
MNO
WXYZ
PQRS
7
9
0
DELETE
REPEAT
SKIP
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Normal Dialling
4 Wait for the connection. Depending on the setting of the receiving
machine, you will either hear a fax tone or the other person will answer.
• If the other party answers, ask them to press their Start key (if you pressed
, pick up the handset to speak with them). This causes the receiving
machine to issue a fax tone.
5 When you hear the fax tone, press START/MEMORY . Replace the handset.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 116).
Note:
If the transmission is unsuccessful and DOCUMENT JAMMED appears in the
display, remove the document as explained on page 134. (This may occur if
the other fax machine doesn’t respond properly when you attempt to send the
document.)
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
Sending a Fax by Automatic Dialling
You can store up to 40 fax or phone numbers in the machine for automatic
dialling.
♦ Auto-dial numbers are dialled by pressing
until the desired number
START/MEMORY
appears in the display, and then
.
Storing fax and phone numbers for automatic dialling
Display:
FUNCTION
1 Press
2 Press
once and
once.
<NEW NUMBER>
ENTER FAX #
once.
3 Enter the fax or voice number by pressing the number keys. Up to 32
digits can be entered. (Note: A space cannot be entered.)
• To clear a mistake, press
.
• If a pause is required between any of the digits to access a special service
FUNCTION
or an outside line, press
. The pause appears as a hyphen. Several
pauses can be entered in a row.
START/MEMORY
4 Press
.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
5 Enter a name by pressing number keys for each letter as shown in the
chart below. Up to 15 characters can be entered. (If you do not wish to
enter a name, go directly to Step 6.)
Example: SHARP = 7777 44 2 777
7
G =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
H =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press
.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
Display:
START/MEMORY
6 Press
.
<NEW NUMBER>
STOP
7 Return to Step 2 to store another number, or press
the date and time display.
to return to
• To confirm that an auto-dial number has been stored correctly, print out the
Telephone Number List as explained on page 115.
Note: The fax machine uses a lithium battery to keep automatic dialling numbers
and other programmed information in memory when the power is turned off.
Battery power is consumed primarily when the power is off. With the power kept
continuously off, the life of the battery is about 5 years. If the battery dies, have
your dealer or retailer replace it. Do not try to replace it yourself.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
Editing and clearing auto-dial numbers
If you need to make changes to a previously stored auto-dial number, or clear
a number, follow these steps:
Display:
FUNCTION
1 Press
2 Press
once and
once.
<NEW NUMBER>
or
until the number you wish to edit or clear appears in
the display.
3 Press
once.
1=EDIT, 2=CLEAR
4 Select EDIT or CLEAR:
EDIT: CLEAR:
1
2
• If you selected CLEAR, go to Step 8.
5 If you selected EDIT, make the desired changes to the number.
• Press
or
to move the cursor to the digit or digits you wish to
change, and then enter the new digit. The new digit will replace the old
digit.
• If you do not wish to change the number, go directly to Step 6.
START/MEMORY
6 Press
.
7 Make the desired changes to the name.
• Press
or
to move the cursor to the letter or letters you wish to
change, and then press the appropriate number key repeatedly until the
desired letter appears (see Step 5 on page 88). The new letter will replace
the old letter.
• If you do not wish to change the name, go directly to Step 8.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
START/MEMORY
8 Press
.
STOP
9 Return to Step 2 to edit or clear another number, or press
return to the date and time display.
to
Using an auto-dial number
Once you have stored a fax or phone number, you can use it to send a fax or
make a phone call.
1 If you are sending a fax, load the
document(s).
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Press
(or
) until the name of the other party appears in the
display (if no name was stored, the number will appear).
3 If you are sending a fax, press START/MEMORY . Dialling and transmission
begins.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 116).
If you are making a phone call, lift the handset. Dialing begins.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
Sending a fax by Direct Keypad Dialling
You can also enter a full number with the number keys and then press the
START/MEMORY
key to begin dialling. You can use this method to dial a full
number when you don't need to speak to the other party before faxing.
1 Load the document(s).
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Enter the number of the receiving machine by pressing the number
keys.
• If a pause is required between any of the digits to access a special service
FUNCTION
or an outside line, press
. The pause will appear as a hyphen.
Several pauses can be entered in a row.
3 Check the display. If the number of the receiving machine shown is
START/MEMORY
correct, press
.
STOP
• If the number is not correct, press
to backspace and clear one digit
at a time, and then re-enter the correct digit(s).
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
Redial
You can automatically redial the last number dialled. This procedure can be
used to send a fax or make a phone call.
1 If you are sending a fax, load the
document(s).
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Press
once. <REDIAL> appears in the display, followed by the last
number dialled. Make sure the number that appears is the number you
wish to dial.
3 If you are sending a fax, press START/MEMORY . Dialling and transmission
begins.
If you are making a phone call, lift the handset. Dialling begins.
Note:
If a fax transmission is unsuccessful and DOCUMENT JAMMED appears in
the display, remove the document as explained on page 134. (This may occur
if the other fax machine doesn’t respond properly when you attempt to send
the document.)
Automatic redialling
If you use automatic dialling (including Direct Keypad Dialling) to send a fax
and the line is busy, the fax machine will automatically redial the number. The
fax machine will make two redial attempts at an interval of five minutes.
During this time, RECALLING will appear in the display, followed by a two-digit
number assigned to the fax job. You will not be able to dial any other locations
while the message appears.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialling
STOP
♦ To stop automatic redialling, press
.
♦ Under certain conditions (for example if a person answers the call on a
telephone), automatic redialling may stop before two redialling attempts are
made.
Error Correction Mode
The fax machine is set to automatically correct any distortions in a
transmission due to noise on the telephone line before printing at the
receiving end. This function is called Error Correction Mode (ECM). ECM is
effective for both transmissions and receptions, and is only effective when the
other fax machine has ECM as well.
When there is considerable noise on the line, you may find that transmission
with ECM turned on takes longer than normal. If you prefer a faster
transmission time, you can try turning ECM off.
FUNCTION
OPTION SETTING
1 Press
2 Press
3 Press
once and
twice.
once and
4 times.
ECM MODE
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
to select YES, or
to
1
2
RECEIVE RATIO
select NO.
STOP
5 Press
to return to the date and
time display.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
Sending a Fax From Memory
You can scan a document into the fax’s memory and send the document from
memory. This increases transmission speed and allows you to send a fax to
multiple destinations in a single operation. After transmission, the document is
automatically cleared from memory.
Broadcasting (sending a fax to multiple destinations)
This function allows you to send the same fax to as many as 20 different
locations in just one operation.
♦ When sending to multiple locations, only auto-dial numbers can be used to
dial the numbers of the receiving machines.
1 Load the document(s).
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
START/MEMORY
2 Press
3 Press
.
(or
) until the name of the number appears in the display
(if no name was stored, the number will appear).
4 Press
to select the number.
5 Repeat Steps 3 and 4 for each of the other locations to which you wish
to send the fax (maximum of 20).
• To check your selected locations, press
to scroll through them. To
STOP
delete a location, scroll to the location and then press
.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
START/MEMORY
6 When you are ready to begin transmission, press
.
• A Transaction Report is automatically printed out after Broadcasting is
completed. Check the "Note" column of the report to see if any of the
locations are marked "Busy" or have a communication error code. If so,
send the document to those locations again.
Memory transmission
You can also send a fax through memory when sending to a single location.
This is convenient when sending to locations where the line is often busy, as it
saves you from waiting to pick up the original document and frees the feeder
for other operations.
To send a fax through memory, load the document, press START/MEMORY , and
then dial using one of the following methods:
♦ Press the number keys to enter the fax number and then press
START/MEMORY
.
♦ Press
repeatedly to select an auto-dial number and press
.
START/MEMORY
START/MEMORY
♦ Press
once to select the last number dialled and press
.
If the memory becomes full...
If the memory becomes full while the document is being scanned, MEMORY
IS FULL and SEE MANUAL will alternately appear in the display.
START/MEMORY
♦ Press
if you want to transmit the pages which have been
stored up to that point in memory. The remaining pages will be ejected from
the feeder. After transmission, the memory will be cleared and you can
transmit the remaining pages. You will also need to transmit the page which
was being scanned when the memory filled up.
STOP
♦ Press
if you want to cancel the entire transmission.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Receiving Faxes
Using TEL/FAX Mode
RECEPTION
To select TEL/FAX mode, press
in the display points to TEL/FAX.
until the arrow
MODE
TEL FAX
RECEPTION
MODE
TEL/FAX A.M.
When the reception mode is set to TEL/FAX, your fax machine automatically
answers all calls on two rings. After answering, your fax monitors the line for
about five seconds to see if a fax tone is being sent.
♦ If your fax machine detects a fax tone (this means that the call is an
automatically dialled fax), it will automatically begin reception of the
incoming document.
♦ If your fax machine doesn't detect a fax tone (this means that the call is a
voice call or manually dialled fax), it will make a ringing sound (called
pseudo ringing) for 15 seconds to alert you to answer. If you don't answer
within this time, your fax will send a fax tone to the other machine to allow
the calling party to send a fax manually if they desire.
Note: Only the fax will alert you to voice calls or manually dialled faxes by
pseudo ringing. An extension phone connected to the same line will not ring
after the connection has been established.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Using A.M. Mode
Pseudo Ring Duration for Tel/Fax Mode
If desired, you can change the duration of pseudo ringing in Tel/Fax mode.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
3 times.
PSEUDO RING
1=15 SECONDS
once.
(Selections appear alternately)
4 Enter a number as follows for the desired duration:
15 SECONDS
30 SECONDS
60 SECONDS
120 SECONDS
1
2
3
4
The display briefly shows
your selection, then:
DISTINCTIVE
STOP
5 Press
to return to the date and time display.
Using A.M. Mode
RECEPTION
MODE
To select A.M. mode, press
A.M.
until the arrow in the display points to
TEL FAX
RECEPTION
MODE
TEL/FAX A.M.
In A.M. mode, your fax machine will automatically receive voice messages
and faxes. See Chapter 3 for more details.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Using FAX Mode
Using FAX Mode
RECEPTION
MODE
To select FAX mode, press
until the arrow in
the display points to FAX.
TEL FAX
RECEPTION
MODE
TEL/FAX A.M.
When the reception mode is set to FAX, the fax machine will automatically
answer all calls on two rings and receive incoming faxes.
♦ If you pick up the handset before the machine answers, you can talk to the
other party and/or receive a fax as explained in Using TEL Mode on page
99.
2 rings
Fax reception
Changing the number of rings
If desired, you can change the number of rings on which the fax machine
answers incoming calls in FAX and TEL/FAX mode. Any number from 2 to 4
can be selected.
Display:
FUNCTION
1 Press
2 Press
once and
twice.
OPTION SETTING
once.
NUMBER OF RING
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
3 Press
once.
ENTER (2-4) (2)
The display briefly shows
your selection, then:
4 Enter the desired number of rings (any
number from 2 to 4).
TRANSACTION
Example: 3 rings
3
STOP
5 Press
to return to the date and time display.
Using TEL Mode
RECEPTION
MODE
To select TEL mode, press
display points to TEL.
until the arrow in the
TEL FAX
RECEPTION
MODE
TEL/FAX A.M.
When the reception mode is set to TEL, you must answer all calls by picking
up the fax machine’s handset or an extension phone connected to the same
line.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
Answering with the fax’s handset
1 When the fax machine rings, pick up
the handset.
2 If you hear a fax tone, wait until the
Beep
display shows RECEIVING and then
replace the handset.
RECEIVING
Note: If you have set the Fax Signal Receive setting
START/MEMORY
(page 102) to NO, press
to begin reception.
3 If the other party first speaks with you
and then wants to send a fax, press
START/MEMORY
RECEIVING
START/MEMORY
after speaking. (Press
before the sender presses their Start
key.)
• When RECEIVING appears in the
display, hang up.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
Answering on an extension phone
You can also start fax reception in TEL mode by answering any extension
phone connected to the same line as the fax machine.
♦ To start fax reception from the cordless handset, see page 38.
1 Answer the extension phone when it
rings.
2 If you hear a soft fax tone, wait until your fax responds (the extension
phone will go dead), then hang up.
Beep
Phone goes dead
• If you have set the Fax Signal Receive setting to NO (see page 102), or if
the fax machine does not respond, set the extension phone down (do not
hang up), walk over to the fax machine, pick up the handset, and press
START/MEMORY
.
Putting a call on hold
PLAY/
To put the other party on hold during a phone conversation, press
.
HOLD
When this is done, they cannot hear you. You can put the handset back in the
cradle without breaking the connection. When you are ready to speak with the
other party again, pick up the handset. If you did not put the handset back in
PLAY/
the cradle, press
again to resume conversation.
HOLD
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
Optional Reception Settings
Fax Signal Receive
Your fax will automatically begin reception if you hear a soft fax tone after
answering a call on your fax or an extension phone. If you use a computer fax
modem to send documents on the same line, you must turn this function off in
order to prevent your fax from mistakenly attempting to receive documents
from the computer fax modem. Follow the steps below to change the setting.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
5 times.
FAX SIGNAL RX
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
to turn on the function, or
1
to turn it off.
CALLER-ID
2
STOP
5 Press
to return to the date and time display.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
Reception Ratio
The fax has been set at the factory to automatically reduce the size of
received documents to fit the size of the printing paper. This ensures that data
on the edges of the document are not cut off. If desired, you can turn this
function off and have received documents printed at full size.
♦ If a document is too long to fit on the printing paper, the remainder will be
printed on a second page. In this case, the cut-off point may occur in the
middle of a line.
♦ Automatic reduction may not be possible if the received document is too
large, contains too many fine graphics or images, or is sent at high
resolution. In this case, the remainder of the document will be printed on a
second page.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
3 times.
RECEIVE RATIO
1=AUTO, 2=100%
once.
The display briefly shows
your selection, then:
4 Press
to select AUTO, or
to
1
2
select 100%.
PRINT CONTRAST
STOP
5 Press
to return to the date and time display.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Substitute Reception to Memory
Substitute Reception to Memory
In situations where printing is not possible, such as when your fax runs out of
paper, the imaging film needs replacement, or the paper jams, incoming faxes
will be received to memory.
When you have received a document in memory, FAX RX IN MEMORY will
appear in the display, alternating with ADD PAPER & PRESS START KEY or
CHECK FILM / CHECK COVER / CHECK PAPER JAM. When you add paper
(and press START/MEMORY ), replace the imaging film, or clear the jam, the stored
documents will automatically print out.
♦ The machine will retain any received faxes in memory until printed, even if
the power cord is unplugged or a power failure occurs.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Making Copies
Your fax machine can also be used to make copies. Single and multiple copies
(up to 99 per original) can be made, enabling your fax to double as a
convenience office copier.
1 Load the document(s) face down.
(Maximum of 10 pages.)
RESOLUTION
• If desired, press
to set the
resolution and/or contrast.
(The default resolution setting for
copying is FINE.)
READY TO SEND
2 If desired, select an enlarge/reduce setting, and/or select the number of
copies per original:
• ENLARGE/REDUCE: Press
or
until the desired setting appears
in the display. Settings are 100%, 125%, 135%, 50%, 73%, 88%, 94%, and
AUTO. (The default setting is 100%.)
Example: Press
twice
RATIO: 125%
• Number of copies per original: Press the number keys to enter a number
from 1 to 99. (The default setting is 1.)
5
Example: Press
for five copies
5
COPY/HELP/POLL
3 When you are ready to begin copying, press
If MEMORY IS FULL appears...
.
If the memory becomes full while a document is being scanned, MEMORY IS
FULL and SEE MANUAL will alternately appear in the display and the
document will automatically feed out. This may happen if the resolution is set
to SUPER FINE, or if you selected an enlarge/reduce setting, or if you are
making more than one copy per original. To avoid using memory, use
STANDARD or FINE for the resolution, 100% for the enlarge/reduce setting,
and make only one copy per original.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Copies
Copy Cut-off
When making a copy of a document that is longer than the printing paper, use
the copy cut-off setting to select whether the remaining part of the document
will be cut off or printed on a second page. The initial setting is YES (cut off
the remainder). To change the setting, follow the steps below.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
once.
COPY CUT-OFF
1=YES, 2=NO
once.
The display briefly shows
your selection, then:
4 Press
to set copy cut-off to YES
1
(the remaining part of the document
NUMBER OF RING
will not be printed), or
to set copy
2
cut-off to NO (the remaining part will be
printed on a second page).
STOP
5 Press
to return to the date and time display.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Special Functions
Caller ID (Requires Subscription to Service)
If you subscribe to a caller identification service from your telephone
company, you can have the fax machine and the cordless handset display the
name and number of the caller when you receive a call.
Important:
♦ To use this function, you must subscribe to a caller identification service
from your telephone company.
♦ Your fax may not be compatible with some caller identification services.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
twice.
OPTION SETTING
once and
5 times.
CALLER-ID
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
(YES) to turn on Caller ID.
1
(To turn off Caller ID, press
.)
2
ECM MODE
STOP
5 Press
to return to the date and
time display.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
How Caller ID operates
When you receive a call, the name and phone number of the caller will
alternately appear in the fax machine display and cordless handset display,
beginning just before the second ring. The information will continue to be
displayed until the line is disconnected.
Display example
JOHN DOE
5258693
Caller’s name
Caller’s number
Note: Some caller ID services may not provide the name of the caller. In this case,
only the phone number will appear.
Display messages
One of the following messages will appear while the fax rings if caller
information is not available.
NO SERVICE
No caller information was received from your telephone
company. Make sure that the telephone company has
activated your service.
CALLER-ID ERROR Noise on the telephone line prevented reception of
caller information.
UNAVAILABLE
The call was made from an area which does not have a
caller identification service, or the caller’s service is not
compatible with that of your local phone company.
PRIVATE
Caller information was not provided by the telephone
company at the caller’s request.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
Viewing the Caller ID list
If you subscribe to a Caller ID service and have turned on the Caller ID
function, your fax machine will keep information on the most recent 30 calls
and faxes you have received. You can view this information, which consists of
the name and number of each caller, in the Caller ID List.
♦ After you have received 30 calls, each new call will delete the oldest call.
Follow the steps below to view the Caller ID List in the display. If desired, you
can immediately dial a number when it appears.
1 Press
twice.
or
<REVIEW CALLS>
2 Press
to scroll through the list.
3 If you want to dial one of the numbers in the list, scroll through the list
until the number appears in the display.
• Fax: If you want to send a fax, load the
START/MEMORY
document and then press
.
Dialling and transmission begin.
Fax:
START/MEMORY
• Voice call: If you want to make a voice
call, pick up the handset (or press
). Dialling begins automatically. (If
Voice
call:
you pressed
, pick up the handset
when the other party answers.)
STOP
4 Press
when you have finished viewing the list.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
To delete calls from the Caller ID list
If you want to delete a single call from the caller list, press
while the
DELETE
call appears in the display. If you want to delete all calls from the list, hold
down for at least 3 seconds while you are viewing any number in the
DELETE
list.
Viewing the Caller ID list from the cordless handset
You can also view the Caller ID list in the cordless handset display, and
automatically dial a number from the list. See page 44.
Priority Call
With Caller ID turned on, you can set your fax machine to make a special
ringing sound when you receive a call from a designated phone number. This
lets you know immediately who is calling without having to look at the display.
♦ This function is only for the fax machine. The cordless handset will not
make a special ringing sound.
To use this function, enter the desired phone number by following the steps
below (only one phone number can be entered).
FUNCTION
Display:
ENTRY MODE
1 Press
2 Press
3 Press
once and
3 times.
once and
once.
PRIORITY #
once.
1=SET, 2=CLEAR
4 Press
to store a number.
1
(To clear a previously stored number, press
and go to Step 6.)
2
5 Enter the number by pressing the number keys (max. 20 digits).
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
START/MEMORY
STOP
6 Press
7 Press
to store (or clear) the number.
to return to the date and time display.
Blocking voice calls
With Caller ID turned on, you can use the Anti Junk Fax function described in
Blocking Reception of Unwanted Faxes in this chapter to block voice calls as
well as faxes from your specified Anti Junk Number.
In this case, when a voice call or a fax comes in from the number you have
specified as a "Junk Number", your fax will terminate the call as soon as it
receives the calling phone number from the caller ID service. The caller will
hear a 3-second high-pitch tone to signal the call’s termination. The call will
not break off until the caller has hung up.
To use this function, enter the number that you wish to block as explained in
Blocking Reception of Unwanted Faxes (see page 113). Only one number can
be blocked.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Subscription to Service)
Distinctive Ring (Requires Subscription to
Service)
If you subscribe to a distinctive ring service from your telephone company, you
will need to turn on the distinctive ring function. When this is done, your fax
will signal voice calls by the normal ring pattern, and fax transmissions by a
special ring pattern. In the case of a fax transmission, your fax machine will
automatically answer the call and receive the fax.
The distinctive ring function is used with the reception mode set to FAX. When
your fax number is dialled, your fax machine will signal the call with a special
ringing sound, then answer automatically and begin reception after the
number of rings set with the Number of Rings setting (see page 98). When
your voice number is dialled, the fax machine will signal the call with the
normal ringing sound to let you know that you must answer personally.
The initial setting for distinctive ring is NO. If set to YES, Fax Duet distinctive
ring is supported.
Important:
♦ The distinctive ring function can only be used if you subscribe to a
distinctive ring service from your telephone company. Do not turn on
distinctive ring if you are on a normal line, as the fax machine will not
operate properly.
♦ If you turn on distinctive ring, the fax will not operate in TEL/FAX reception
mode.
Display:
FUNCTION
1 Press
2 Press
once and
twice.
OPTION SETTING
once and
4 times.
DISTINCTIVE
3 Press
4 Press
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
to turn on the function, or
to turn it off.
1
FAX SIGNAL RX
2
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking Reception of Unwanted Faxes
STOP
5 Press
to return to the date and time display.
TEL FAX
6 Set the reception mode to FAX.
RECEPTION
MODE
TEL/FAX A.M.
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes from a party
that you specify. This saves paper by not printing out unwanted "junk" faxes.
To use this function, follow the steps below to enter the fax number from which
you do not wish to receive faxes. One fax number can be entered.
Display:
FUNCTION
1 Press
once and
3 times.
ENTRY MODE
ANTI JUNK #
2 Press
3 Press
once and
twice.
1=SET, 2=CLEAR
once.
4 Press
to store an Anti Junk number, or
to clear a previously
1
2
stored number (if you are clearing a number, go to Step 6).
5 Enter the fax number by pressing the number keys (max. 20 digits).
START/MEMORY
6 Press
STOP
7 press
to return to the date and time display.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Polling (Requesting a Fax Transmission)
Polling allows you to call another fax machine and have it send a document to
your machine without operator assistance. In other words, the receiving fax
machine, not the transmitting fax machine, initiates the transmission.
1 Dial the fax machine you want to poll
using one of the following methods:
• Enter the full number using the numeric keys.
• Pick up the handset (or press
) and dial the full number. Wait for the
fax answerback tone.
• If the number has been stored for automatic dialling, press
or
until the name (or number) of the other party appears in the display.
COPY/HELP/POLL
2 Press
.
• If you used the handset, replace it when POLLING appears in the display.
Reception will begin.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Printing Lists
You can print lists showing settings and information entered in the fax
machine. The lists are described below. To print a list, follow these steps.
Display:
FUNCTION
1 Press
once and
twice.
LISTING MODE
TEL # LIST
2 Press
3 Press
4 Press
once.
or
until the desired list appears in the display.
once.
PRESS START KEY
START/MEMORY
5 Press
to print the list.
Telephone Number List
This list shows the fax and phone numbers that have been stored for
automatic dialling.
Setup List
This list shows your current selections for the FUNCTION key settings. The
list also shows your name and fax/telephone number as entered in the
machine, and a sample of the header printed at the top of every page you
transmit (HEADER PRINT).
Message List
This list shows information about the messages currently recorded in the
answering system, including the date and time each messages was recorded,
the length, and the type.
Caller-ID List
This list shows information about your 30 most recent calls. (This list is only
available if you are using the Caller ID function.)
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report
This report is printed out automatically after an operation is completed to
allow you to check the result. Your fax machine is set at the factory to print out
the report only when an error occurs.
♦ The Transaction report cannot be printed on demand.
Headings in Transaction Report
SENDER/
RECEIVER
The name or fax number of the other machine involved in the
transaction. If that machine does not have an ID function, the
communication mode will appear (for example, "G3").
START
The time at which transmission/reception started.
Total time taken for transmission/reception.
Number of pages transmitted/received.
TX/RX TIME
PAGES
NOTE
(One of the following notes will appear under NOTE in the
report to indicate whether the transaction was successful,
and if not, the reason for the failure.)
OK - Transmission/reception was successful.
P.FAIL - A power failure prevented the transaction.
JAM - The printing paper or document jammed, preventing
the transaction.
BUSY - The fax was not sent because the line was busy.
COM.E-X - (Where “X” is a number.) A telephone line error
prevented the transaction. See Line error on page 123.
CANCEL - The transaction was cancelled because the
STOP key was pressed, no document was in the feeder, or
the other machine requested transmission using a function
which your fax machine does not have. If you were
attempting to fax, make sure a document is in the feeder. If
you were receiving, contact the faxing party to see how they
are trying to send to you.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report print condition
You can change the condition under which a Transaction Report is printed out.
Follow the steps below.
Display:
FUNCTION
1 Press
once and
twice.
OPTION SETTING
TRANSACTION
2 Press
3 Press
once and
once.
1:ALWAYS PRINT
once.
(Selections appear alternately)
4 Press a number from
to
to select the condition for printing.
1
5
ALWAYS PRINT
A report will be printed after each
transmission, reception, or error.
1
2
ERROR/MEMORY
SEND ONLY
A report will be printed after an error or a
memory operation.
3
4
5
A report will be printed after each
transmission.
ERROR ONLY
NEVER PRINT
A report will be printed only when an error
occurs.
A report will never be printed.
The display briefly shows
your selection, then:
DIAL MODE
STOP
5 Press
to return to the date and time display.
Help List
This list provides a brief guide to the operation of the machine. Press
COPY/HELP/POLL
while no document is loaded in the feeder to print the list.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
Print head
Clean the print head frequently to ensure optimum printing performance.
Note: Remove the paper from the paper tray before cleaning the print head.
1 Unplug the telephone line and then the
power cord, and open the operation
panel (press ➊).
2
1
2 Take the imaging film out of the print
compartment and place it on a sheet of
paper.
3 Wipe the print head with isopropyl
alcohol or denatured alcohol.
Caution!
• Do not use benzene or thinner. Avoid
touching the print head with hard
objects.
• The print head may be hot if your fax
machine has just received a large
number of documents. If this is the
Print head
case, allow the print head to cool prior
to cleaning.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4 Place the imaging film back in the print
compartment.
5 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
Scanning glass and rollers
Clean the scanning glass and rollers frequently to ensure the quality of
transmitted images and copies.
Note: Remove the paper from the paper tray before cleaning the scanning
glass and rollers.
1 Open the operation panel (press ➊).
2
1
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
2 Flip up the green levers on each side of
the white roller.
3 Wipe the scanning glass (under the
white roller) and rollers with a cotton
swab.
• Make sure that all dirt and stains (such
as correcting fluid) are removed. Dirt
and stains will cause vertical lines on
transmitted images and copies.
If the scanning glass is difficult to clean
If you find it difficult to remove dirt from the scanning glass, you can try moistening
the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol
gets on the rollers.
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
The housing
Wipe the external parts and surface of the machine with a dry cloth.
Caution! Do not use benzene or thinner. These solvents may damage or
discolor the machine.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Replacing the Cordless Handset Batteries
Like any other battery, the rechargeable batteries will eventually wear out. The
batteries can normally be used for about two years, although this will vary
depending on the conditions of use.
If you find that
or
appears in the cordless handset display soon after
the batteries are charged, replace them with the following batteries:
Replacement batteries: Use only 1.2 V Ni-MH batteries with a capacity of
630 mAh (min. of 600 mAh; type AAA).
Caution:
Danger of explosion if batteries are incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
1 Remove the battery cover by pressing
on the indentation as shown.
2 Remove the old batteries.
3 Insert the new batteries.
+
-
+
-
+
-
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4 Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
5 Place the cordless handset in the
charger with the dial pad facing
forward.
• Let the new batteries charge for at least
12 hours.
Battery disposal
The batteries are Nickel Metal Hydride batteries. The batteries must be
disposed of properly. Contact local agencies for information on recycling and
disposal plans in your area.
Wiping the charger contacts
To ensure that the battery charges properly, wipe the charger contacts once a
month with a cotton swab.
Charger contacts
122
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Troubleshooting
Problems and Solutions
Line error
Problem
Solution
LINE ERROR appears in
the display.
Try the transaction again. If the error persists, check
the following:
• Check the connection. The cord from the TEL.
LINE socket to the wall socket should be no longer
than two meters.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the fax machine to a different
telephone line.
• If the problem still occurs, your fax machine may
need service.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Dialling and transmission problems
Problem
Solution
No dial tone when you
pick up the handset or
• Make sure the handset cord is connected to the
correct socket. See Connecting the handset on
page 17.
press the
key.
Dialling is not possible.
• Make sure the power cord is properly plugged into
a power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE socket and the
wall socket.
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• Make sure that the telephone line cord is plugged
into the TEL. LINE socket, and not the TEL. SET
socket.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Check the display for error messages.
• Pick up the handset and check for a dial tone.
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion.
Try sending the document again.
• Make a copy of the document on your fax machine.
If the copy is also distorted, your fax machine may
need service.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Reception and copying problems
Problem
Solution
The power is on, but no
reception takes place.
• Make sure that the telephone line cord is plugged
into the TEL. LINE socket, and not the TEL. SET
socket.
The printing paper comes • Make sure that the document is loaded properly in
out blank when you try to
receive a document.
the feeder of the transmitting machine. Make a
copy or print a report to confirm the printing ability
of your machine.
General print quality is
poor.
• It is important to select a paper that is appropriate
for the thermal transfer printer in your fax. We
recommend using laser quality paper that has a
very smooth finish. Copier paper will work, but it
sometimes tends to yield a lighter print quality.
The received document is • Ask the other party to send higher contrast
faint.
documents. If the contrast is still too low, your fax
machine may need service. Make a copy or print a
report to check your machine’s printing ability.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document
again.
• The print head may be dirty. See Print head on
page 118.
• Make a copy or print a report on your fax machine.
If the copy or report is also distorted, your fax
machine may need service.
A received document or
copy prints out in strips.
• Make sure the operation panel is completely closed
(press down on both sides of the panel).
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will
cause spots to appear on copies and transmitted
faxes. Clean the scanning glass as explained on
page 119.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Reception/copying is
interrupted.
• If reception or copying takes place continuously for
a long time, the print head may overheat. Turn off
the power and let it cool down. If overheating
frequently occurs, try changing the print contrast
setting to LIGHT (see page 27).
Dark vertical lines appear • Try changing the print contrast setting to LIGHT
on copies and received
faxes.
(see page 27).
General problems
Problem
Solution
A loud howling sound
occurs when the speaker
is used.
• Feedback (a loud howling sound) may occur if you
replace the handset while the speaker is on. To
avoid feedback, turn off the speaker (press
before you replace the handset.
)
Auto-dial numbers cannot • Make sure the fax is plugged in and the imaging
be stored in the fax.
film has been loaded. (Auto-dial numbers cannot
be stored if the imaging film has not been loaded.)
See Loading the Imaging Film on page 24.
Nothing appears in the
display.
• Make sure the power cord is properly plugged into
a power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the
keys, unplug the power cord and then plug it in
again several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable Documents on page 81).
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Cordless handset problems
Problem
Solution
The cordless handset
does not operate and
nothing appears in the
display.
• Make sure the batteries are correctly inserted in the
cordless handset (see page 21).
• The batteries may be low. Place the cordless
handset in the charger and let it charge.
Calls cannot be made or
received on the cordless
handset.
• Make sure the fax machine is plugged into a power
outlet and has power.
• Make sure the telephone line is properly connected
to both the TEL. LINE socket on the fax machine
and the wall jack (see page 18). (If the telephone
line is connected correctly, you should hear a dial
tone when you pick up the fax machine handset.)
• The batteries may be low. Place the cordless
handset in the charger and let it charge.
• Calls cannot be made or received while the fax
machine is being used (while BUSY appears in the
cordless handset display). Wait until the fax
machine is no longer being used.
• Calls cannot be made or received during a power
failure.
• You may be outside of the talking range. Move
closer to the fax machine.
You hear noise or
interference during a call.
• Other electrical appliances may cause interference.
Move away from any electrical appliances.
• Move closer to the fax machine. Note that large
metal objects, metal structures, and thick walls
between the fax machine and cordless handset will
reduce the talking range. If needed, try moving the
fax machine to a different location.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
The batteries do not
charge.
• Make sure the cordless handset is placed in the
charger with the dial pad facing forward.
• Make sure the AC adapter is connected correctly to
the charger and the power outlet (see page 20).
• Wipe the charger contacts with a cotton swab.
• Make sure the batteries are correctly inserted in the
cordless handset (see page 21).
• The batteries may need replacement (see page
121).
You hear beeps during a
call.
• You will hear beeps during a call and
will blink
in the display if the batteries are low. Place the
cordless handset in the charger and let it recharge.
If you hear beeps during a call and need to
continue the call, transfer the call to the fax
machine (see page 47).
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Messages and Signals
Display messages (fax machine)
Note: If you have turned on the Caller ID function, see page 108 for display
messages related to Caller ID.
ADD PAPER & /
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add
paper and then press the START/MEMORY key. If
there is paper in the tray, make sure it is inserted
correctly (take out the stack, align the edges evenly,
and then reinsert it in the tray) and then press the
START/MEMORY key.
A.M. TRANSFER
CALL TRANSFER
The answering system's transfer function has been
turned on (see page 70).
A call is being transferred. (On occasion, this may
also appear while paging the cordless handset for an
intercom call.)
CHECK FILM/
CHECK COVER/
CHECK PAPER JAM
(alternating messages)
These alternating messages appear when there is a
problem in the print compartment that prevents
printing. Check to see if the imaging film is not loaded
properly or if it has been used up and needs
replacement. Make sure the operation panel is
completely closed (press down on both sides). If a
paper jam has occurred, clear the jam as explained in
the following section, Clearing Paper Jams.
CHECK PAPER SIZE
DECT HS IN USE
An incorrect size of paper has been loaded in the
paper tray. Remove the paper and load A4-size
paper.
The cordless handset is in use. Wait until this
message no longer appears to send a fax or make a
phone call from the fax machine.
DOCUMENT JAMMED
The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will
occur if you load more than 10 pages at once or load
documents that are too thick (see page 81).
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
FAX RX IN MEMORY
A fax has been received in memory because the
imaging film needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will
print out automatically when the problem is fixed.
FUNCTION MODE
HOLD
The FUNCTION key has been pressed.
The HOLD key has been pressed to place a call on
hold. Press the HOLD key again to resume the call.
INCORRECT FILM/
CHECK FILM
The wrong type of imaging film is loaded in the
machine. Printing is not possible. The machine can
only print when SHARP FO-9CR imaging film is
loaded.
INTERCOM
A cordless handset is paging the fax machine (lift the
handset to talk), or the fax machine is paging a
cordless handset. The name and number of the
cordless handset appear alternately with
INTERCOM.
LINE ERROR
Transmission or reception was not successful. Press
the STOP key to clear the message and then try
again. If the error persists, see Line Error on page
123.
MEMORY IS FULL/
SEE MANUAL
(alternating messages)
The memory is full. You may have too many
messages recorded in the answering system. To
erase messages, see page 67.
This message may also occur during fax reception if
too much data is received before the pages can be
printed out. If faxes have been received to memory
because printing is not possible (an additional
message will indicate the problem), resolve the
problem so that printing can continue (see Substitute
Reception to Memory on page 104). If you are
attempting to transmit from memory, see If the
memory becomes full on page 95. If you are copying,
see If MEMORY IS FULL appears on page 105.
MEMORY PRINTING
The fax is preparing to or printing out a document
from memory.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
NEAR END OF FILM/
REPLACE FILM
This message appears 3 m from the end of the
imaging film (approximately 10 pages can still be
printed), and alerts you that you will soon need to
replace the film.
NO DATA
This appears if you attempt to search for an auto-dial
number when none have been stored.
NOT REGISTERED
OFF HOOK
You attempted to delete, page, or transfer a call to a
cordless handset that is not registered.
This appears if you forgot to replace the handset after
using it to dial and send a fax. Replace the handset or
press the STOP key to clear the message.
ON HOOK DIAL
OVER HEAT
The
key has been pressed and the fax machine
is waiting for you to dial.
The print head has overheated. Operation can be
continued after it cools. If overheating frequently
occurs, try changing the print contrast setting to
LIGHT (see page 27).
PRINT HEAD FAIL/
The print head has failed and requires service.
YOU NEED SERVICE
(alternating messages)
READY TO SEND
RECALLING
A document has been loaded and the fax machine is
waiting for you to begin faxing or copying.
This appears if you attempt to send a fax by
automatic dialling and the line is busy or the receiving
fax machine does not answer. Your fax machine will
automatically reattempt the call. (See Automatic
redialling on page 92.)
REPLACE HANDSET
This appears if an outside call comes in while you are
paging or talking to the cordless handset using the
Intercom feature. Replace the fax machine handset to
stop the Intercom call, and then pick it up again to
answer the outside call. This also appears after you
transfer a call to the cordless handset.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
MESSAGES RCVD:XX
TOTAL PAGE(S) 01
This indicates that you have received messages in
the answering system. “XX” is the number of
messages.
Number of pages transmitted, received, or copied.
Display messages (cordless handset)
BUSY
When you attempt to make a phone call or page
another device (fax machine or cordless phone), the
system or other device is busy and cannot respond.
Wait until the system or device is no longer busy. This
message may also appear if you are slightly out of the
communication range and you attempt to make a
phone call (try moving closer to the fax machine; note
that the display may still indicate that you are in
range).
C (blinking)
CALLS
has been pressed to place a call on hold. To
resume the call, press
again.
This appears when you access the Caller ID list in the
fax machine by holding down
Caller ID).
(only if you have
EMPTY
This appears if you access the fax machine’s phone
book or Caller ID list and there are no numbers.
0 - 6
Your cordless handset is being paged (press
to
(a number from 0 to 6
appears)
answer), or your cordless handset is paging the fax
machine or another cordless handset.
The cordless handset batteries are low and need
recharging. Place the cordless handset in the
charger. If this appears soon after the batteries have
been charged, the batteries may need replacement
(see page 121). If this appears during a phone call
(you will also hear beeps) and you need to continue
the call, transfer the call to the fax machine.
(blinking)
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
Rapid intermittent
tone
35 seconds
(0.7 seconds on,
0.3 seconds off)
Indicates that the handset is off hook.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying,
or DOCUMENT JAMMED appears in the display, first try pressing
START/MEMORY . If the document doesn't feed out, remove it as explained below.
Important:
Do not try to remove a jammed document without releasing it as explained
below. This may damage the feeder mechanism.
1 Press ➊ and slowly open the operation
panel until it is half open.
2
1
2 Flip up the green levers on each side of
the white roller.
3 Gently remove the document.
• Be careful not to tear the document.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
Clearing jammed printing paper
1 Open the operation panel (press ➊).
2
1
2 Gently pull the jammed paper out of
the machine, making sure no torn
pieces of paper remain in the print
compartment or rollers.
3 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Reference Guide
Sending Faxes
Receiving Faxes
TEL FAX
01-JAN 10:30
01-JAN 10:30
01-JAN 10:30
TEL/FAX A.M.
TEL FAX
Place your document
(up to 10 pages) face
down in the document
feeder.
RECEPTION
MODE
TEL/FAX A.M.
TEL FAX
TEL/FAX A.M.
TEL FAX
01-JAN 10:30
TEL/FAX A.M.
FAX mode: The fax machine automatically
answers and receives faxes.
Normal Dialling
TEL mode: Answer all calls (even faxes)
by picking up the handset. To begin fax
1.Lift the handset or press
2.Dial the fax number.
.
START/MEMORY
reception, press
.
3.Wait for the reception tone (if a person
answers, ask them to press their Start
key).
TEL/FAX mode: The fax machine
automatically answers and receives faxes.
Voice calls are signalled by a special
ringing sound.
START/MEMORY
4.Press
.
Automatic Dialling
A.M. mode: Select this mode when you go
out to receive both voice messages and
faxes.
1.Press
or
until the desired
destination appears in the display.
Storing Auto Dial Numbers
START/MEMORY
2.Press
.
FUNCTION
1.Press
once and
twice.
Direct Keypad Dialling
2.Enter the full fax/phone number.
1.Dial the fax number.
START/MEMORY
3.Press
.
START/MEMORY
2.Press
.
4.Enter a name by pressing number keys.
(To enter two letters in succession that
Recording an Outgoing
Message
require the same key, press
after
entering the first letter.)
G =
H =
N =
U =
V =
SPACE =
A =
REC/
1.Press
,
, and
.
MEMO
O =
P =
Q =
R =
S =
T =
B =
C =
D =
W =
X =
Y =
Z =
I
=
START/MEMORY
J =
K =
L =
2.Lift the handset, press
speak into the handset.
, and
E =
F =
M =
STOP
3.When finished, press
.
START/MEMORY
STOP
5.Press
and then
.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Reference Guide
Storing auto dial numbers
1. Press and then press
Using the Cordless Phone
twice.
Making a phone call
1. Pick up the cordless handset and press
.
2. Enter a name for the auto-dial number.
To enter each letter, hold down the key
for the letter as shown in the chart
below until the letter appears in the
display.
2. When you hear the dial tone, dial the
number.
SPACE, PAUSE ( ),
-
=
M, N, O =
P, Q, R, S =
T, U, V =
# ( ), ?, _ =
A, B, C =
3. When you are ready to end the call,
D, E, F =
press
.
W, X, Y, Z =
=
G, H, I =
J, K, L =
3. Press
.
Making a phone call using automatic
dialling
4. Enter the full fax/phone number.
1. Press
once.
To clear a mistake, press
.
To insert a pause, hold down
until
2.Press
or
until the number you
“
” appears.
wish to dial appears in the display.
5. Press
exit.
and then
repeatedly to
3. Press
.
Listening to messages
Receiving a phone call
1. When the cordless handset rings, pick it
1. Press
2. Press
and then press
to listen to all your
to listen to only your
.
up and press
.
2. When you are ready to end the call,
press
messages, or
new messages.
3. While listening, you can do the following:
.
Receiving a fax using the cordless
handset
Repeat a message: Press
Skip a message: Press
.
.
If you hear a fax tone after answering a
call on the cordless handset, or if the
other party speaks to you and then
Delete a message: Press
message is playing.
while the
Stop playback: Press
.
wants to send a fax, press
.
4 When finished, press
repeatedly to
exit.
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Ringer volume, 50
System PIN, 57
Talking range, 23
Turning off ringer, 51
Viewing calls, 44
A
A.M. reception mode, 32, 64
Anti Junk Fax, 113
Audible signals, 133
Auto-dial numbers
Storing, 38, 87
D
Using, 40, 90
Date, setting, 30
Dial mode, 18
Dialling
B
Battery
Automatic, 40, 90
Direct Keypad, 91
Normal, 36, 85
Disposing of, 122
Installing, 21
Replacing, 121
Direct Keypad Dialling, 91
Display messages, 129
Distinctive ring, 112
Document feeder, 82
Document guides, 82
Document restrictions, 82
Document sizes, 81
Document, maximum scanning size, 81
C
Call time, 52
Caller ID, 107-111
Caller ID List, 115
Contrast, 84
Copies, 105
Copy cut-off setting, 106
Cordless handset
Auto-dial numbers, storing, 38
Auto-dial numbers, using, 40
Automatic registration, 55
Beeps, 52
E
ECM (Error Correction Mode), 93
Extension telephone
Connecting, 20
Using, 101
Deleting, 62
Deleting calls, 45
Display language, 61
End call setting, 53
Faxes, receiving, 38
Hold, 37
Listening to messages, 54
Making a call, 36
Melody, 50
F
Fax Duet (distinctive ring), 112
Fax mode on TAD failure, 68
FAX reception mode, 32, 98
Fax Signal Receive, 102
H
Power, 53
Halftone setting, 83
Handset, 17
Quick Search, 41
Receiver volume, 36
Receiving a call, 37
Redial, 44
Hold, 101
Housing, cleaning, 120
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Power cord, 17
I
Print contrast setting, 27
Print head, cleaning, 118-119
Priority Call, 110
Imaging film, replacing, 24
Intercom, 45
Pseudo Ring Duration, 97
J
Jams, clearing, 134-135
R
Reception mode
L
A.M. mode, 32, 64
FAX mode, 32, 98
TEL mode, 32, 99
TEL/FAX mode, 32, 96
Reception Ratio setting, 103
Redialling, 92
Letters, entering, 29, 39, 88
Line error, 123
Loading paper, 26
Loading the document, 82
Remote code number, 74
Remote operations, 74
Resolution, 83
M
Memory transmission, 95
Memory, substitute reception to, 104
Message List, 115
Ringer volume
Fax machine, 34
Messages
Erasing, 67
Listening to, 66
Listening to remotely, 75
Setting allowed time, 68
S
Scanning glass, cleaning, 119
Sender’s name and number, entering,
28-29
Setup List, 115
Speaker volume, 33
N
Normal Dialling, 36, 85
Number of rings in A.M. mode, 65
Number of rings in FAX reception mode,
98
T
TEL reception mode, 32, 99
TEL. LINE socket, 18
TEL. SET socket, 20
O
TEL/FAX reception mode, 32, 96
Telephone line cord, 18
Telephone Number List, 115
Time, setting, 30
Toll Saver function, 65, 74
Transaction Report, 116
Setting print condition, 117
Transfer Function, 70
OGM only mode, 69
Outgoing message, 63
P
Paper jams, clearing, 134-135
Paper tray extension, 19
Paper, loading, 26
Polling, 114
Transferring calls, 47
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE OPERATION CARD
The card below is provided as a quick guide to remote operation. Cut it out
and carry it with you when you go out.
Remote Operation Guide
1. Call your fax from a touch-tone telephone, and
press # when the outgoing message begins.
2. Enter your remote code:
.
3. Press # .
4. After listening to your messages, you can either
hang up to save them, or enter one of the
commands on the reverse side.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE COMMANDS
•
FAX RECEPTION MODES
•
PLAYBACK
A.M. mode........................
FAX mode.........................
TEL mode.........................
TEL/FAX mode .................
8
8
8
8
1
2
3
4
#
#
#
#
Play messages .................
Move backward/repeat......
Skip forward......................
Stop ..................................
Play new messages only ..
(first stop playback)
7
2
5
0
6
#
#
#
#
#
•
TRANSFER FUNCTION
Turn on .............................
Turn off .............................
New transfer number........
(Tel. No.) #
Record transfer OGM .......
9
9
9
1
2
0
#
#
#
•
•
•
ERASING MESSAGES
Erase single message ......
Erase all messages ..........
3
3
#
3
#
9
3
#
RECORDING A MEMO
To quickly disconnect........ * *
Start.................................. * #
End ...................................
0
4
#
•
OGM ONLY MODE
Turn on .............................
Turn off .............................
1
1
1
2
#
#
RECORDING A NEW OGM
Start..................................
*
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION OF AUSTRALIA PTY.LTD.
A.C.N. 003 039 405
1 Huntingwood Drive, Huntingwood, Blacktown, N.S.W., 2148
SHARP CORPORATION
PRINTED IN THAILAND
(TINSE4432XHTZ)
Download from Www.Somanuals.com. All Manuals Search And Download.
|