OPERATION MANUAL
MODEL
-
XG NV7XU
DIGITAL MULTIMEDIA
PROJECTOR
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to
defeat the safeguards incorporated into this Projector, observe the following basic rules for its installation, use and servicing.
For your own protection and reliable usage of your projector, please be sure to read these “IMPORTANT SAFEGUARDS”
carefully before use.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read
before the product is operated.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.
2. Retain Instructions
The safety and operating instructions should be retained
for future reference.
14. Lightning
3. Heed Warnings
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
15. Overloading
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
6. Attachments
16. Object and Liquid Entry
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
7. Water and Moisture
Do not use this product near water–for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to
the product. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. If the product exhibits a distinct change in
performance, this indicates a need for service.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product and
to protect it from overheating. The openings should never
be covered or blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating
condition.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type
plug.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Outstanding Features
1. DIRECT DIGITAL COMPUTER INPUT (PanelLink™)
Signals remain digital from the source device to the projector thus resulting in sharper, clearer, noiseless and adjustment-free
computer images.
X
2. ADVANCED COMPATIBILITY WITH HIGH-END WORKSTATIONS
AND PCS
L
H
Compatible with up to 200 Hz vertical refresh rate, Sync on Green and Composite Sync signals
for use with a wide variety of high-end PCs and Workstations. (Page 11)
3. FOR USE WITH DTV*/HDTV
Allows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder
or similar video systems. (Page 13)
4. COMPONENT VIDEO COMPATIBILITY (VIA RGB)
Equipped with terminals for connection to a DTV decoder, DVD player and similar video systems for higher quality images.
(Page 13)
5. ADVANCED VIDEO CIRCUITRY
Provides high quality video images with minimal noise for more impressive presentations.
6. DIGITAL KEYSTONE CORRECTION
Digitally adjusts an image that is projected at an angle while maintaining image quality and
brightness. (Page 19)
7. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
A multi-color, icon based menu system allows for simple image adjustments. (Page 23)
8. USER-FRIENDLY DESIGN
The two-color design along with an intuitive Graphical User Interface (GUI) makes this projector
very easy to set up and adjust.
9. WIRELESS PRESENTATIONS WITH IrCOM
The IrCOM function allows for wireless transmission of digital images via infrared
communication from a PC or digital camera. (Page 25)
10. AUTO SYNC TECHNOLOGY FOR AUTOMATIC IMAGE
PERFECTION
Automatically makes any necessary adjustments for perfectly synced computer images.
(Page 29)
11. INTELLIGENT COMPRESSION AND EXPANSION
By using intelligent resizing technology, this projector can display higher and lower resolution images in detail without
compromising quality. (Page 36)
12. XGA RESOLUTION FOR HIGH RESOLUTION PRESENTATIONS
With XGA (1,024
ן 768) resolution, this projector can display very detailed presentation information. 13. UXGA COMPATIBLE
UXGA (1,600
ן 1,200) resolution images are intelligently resized to 1,024 ן 768 for full-screen or default presentations. 14. CUSTOMIZABLE STARTUP SCREEN
Allows you to load a custom startup image (i.e. your company logo) to be displayed while the projector is warming up.
(Page 42)
15. BUILT-IN PRESENTATION TOOLS
A variety of helpful presentation utilities are incorporated to enhance presentations. These include “Stamp” functions, “Break
Timer”, and “Digital Enlarge”. (Page 44)
16. QUIET OPERATION
The quiet fan operation allows the audience to concentrate on the presentation without the distraction of fan noise.
*DTV is the umbrella term used to describe the new digital television system in the united states.
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Information
Useful Features
IMPORTANT SAFEGUARDS ……………………
Outstanding Features ……………………………
Contents ……………………………………………
Usage Guidelines …………………………………
How to Access the PDF Operation Manuals
(for Windows and Macintosh) ………………
For SHARP Assistance (U.S.A. only) …………
Part Names …………………………………………
2
3
4
5
Freeze Function …………………………………… 33
Digital Image Magnification (ENLARGE) ……… 34
Gamma Correction ……………………………… 35
Selecting the Picture Display Mode …………… 36
Black Screen Function …………………………… 37
On-screen Display Override Function ………… 37
Automatic Power Shutoff Function …………… 38
I/P Conversion …………………………………… 39
Checking the Lamp UsageTime ……………… 39
Selecting the Signal Type ……………………… 40
Checking the Input Signal ……………………… 40
Setting a Background Image …………………… 41
Selecting a Startup Image ……………………… 42
Reverse/Invert Image Function ………………… 43
Using the Presentation Tools …………………… 44
Status Function …………………………………… 45
6
6
7
Setup & Connections
Supplied Accessories …………………………… 10
Connecting the Projector ……………………… 11
Operation
Maintenance & Troubleshooting
Basic Operations ………………………………… 16
Setting up the Screen …………………………… 18
Operating the Wireless Mouse from the
Remote Control ……………………………… 21
Using the GUI (Graphical User Interface)
Lamp/Maintenance Indicators ………………… 47
Replacing the Projection Lamp ………………… 48
Using the Kensington Lock …………………… 49
Troubleshooting …………………………………… 49
Menu Screens ………………………………… 23
Using IrCOM for Wireless Presentations……… 25
Selecting the On-screen Display Language … 26
Selecting the Video Input System Mode
Appendix
(VIDEO mode only) …………………………… 26
Picture Adjustments ……………………………… 27
Audio Adjustments ……………………………… 28
Computer Image Adjustments ………………… 29
Auto Sync Adjustment ………………………… 30
Auto Sync Display Function…………………… 30
Saving and Selecting Adjustment Settings … 31
Special Mode Adjustment …………………… 32
Transporting the Projector ……………………… 51
Connection Pin Assignments…………………… 52
RS-232C Port Specifications …………………… 53
Input Signals (Recommended Timing)………… 55
Specifications ……………………………………… 57
Dimensions ………………………………………… 58
Guide to Effective Presentations ……………… 59
Glossary …………………………………………… 63
Index ………………………………………………… 64
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Usage Guidelines
"COMPLIES WITH 21 CFR SUBCHAPTER J"
Cautions Concerning the Laser Pointer
SHARP ELECTRONICS CORPORATION
CAUTION
DO NOT STARE INTO BEAM
WAVE LENGTH : 650nm
MAX. OUTPUT : 1mW
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
TEL : 1-800-BE-SHARP
U.S.A. ONLY
LASER RADIATION-
REMOTE CONTROL
MODEL NO. : RRMCG1530CESA
DC3V (1.5VX2PCS.)
The laser pointer on the remote control emits a laser beam from the laser
pointer window. This is a Class II laser which may impair your sight if directed
into the eyes. The three marks shown on the left are caution labels for the
laser beam.
• Do not look into the laser pointer window or shine the laser beam on yourself or
others. (The laser beam used in this product is harmless when directed onto
the skin. However, be careful not to project the beam directly into the eyes.)
• Always use the laser pointer at temperatures between 41°F and 95°F (
ם 5°C and
ם 35°C). MADE IN CHINA
CLASS II LASER PRODUCT FABRIQUÉ AU CHINE
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
• Use of controls or adjustments, or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Laser pointer
window
Cautions Concerning the Setup of the Projector
95˚F
(
ם 35˚C) For minimal servicing and to maintain high image quality, SHARP recommends
that this projector be installed in an area free from humidity, dust and cigarette
smoke. When the projector is subjected to these environments, the lens and
filter must be cleaned more often. Periodically the filter should be replaced
and the projector should be cleaned internally. As long as the projector is
properly maintained in this manner, use in these environments will not reduce
the overall operation life. Please note that all internal cleaning must be
performed by an Authorized Sharp Industrial LCD Products Dealer or Service
Center.
41˚F
(
ם 5˚C) Notes on Operation
• The two marks shown on the left are caution labels for parts of the projector
that emit intense heat during operation.
• The exhaust vents, the lamp cage cover and adjacent areas may be extremely
hot during projector operation. To prevent injury, do not touch these areas until
they have sufficiently cooled.
• Allow at least 4 inches (10 cm) of space between the cooling fan (exhaust
vent) and the nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will automatically
turn off the projector lamp. This does not indicate a malfunction. Remove the
projector power cord from the wall outlet and wait at least 10 minutes. Then
turn on the power by plugging the power cord back in. This will return the
projector to the normal operating condition.
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter, “TEMP.”
and “ ” will flash in the lower-left corner of the picture. If the temperature continues
to rise, the lamp will turn off, the TEMPERATURE WARNING indicator on the
projector will flash, and after a 90-second cooling-off period the power will shut
off. Refer to “Lamp/Maintenance Indicators” on page 47, for details.
• The cooling fan regulates the internal temperature, and its performance is
automatically controlled. The sound of the fan may change during projector
operation due to changes in the fan speed.
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals (for Windows and Macintosh)
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to
install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet,
To Install Acrobat Reader (English version) from the CD-ROM
For Windows:
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “manuals” folder.
5 Double click on the “acrobat” folder.
6 Double click on the “windows” folder.
7 Double click on the installation program and follow
the instructions on the screen.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “CD-ROM” icon.
3 Double click on the “manuals” folder.
4 Double click on the “acrobat” folder.
5 Double click on the “mac” folder.
6 Double click on the installation program and follow
the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for other languages, please download the appropriate version from the Internet. (Please
note that you do not have to have Acrobat Reader in your own language. You can read any pdf file using the English version of
Acrobat Reader.)
Accessing the PDF Manuals
For Windows:
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “manuals” folder.
5 Double click on the “xg-nv7xu” folder.
6 Double click on the language (name of the folder)
that you want to view.
7 Double click on the “nv7” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
8 Double click on the pdf file.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “CD-ROM” icon.
3 Double click on the “manuals” folder.
4 Double click on the “xg-nv7xu” folder.
5 Double click on the language (name of the folder)
that you want to view.
6 Double click on the “nv7” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
7 Double click on the pdf file.
• If the desired pdf file cannot be opened by double clicking the mouse, please start Acrobat Reader first, then specify the
desired file using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for information on the CD-ROM.
For SHARP Assistance (U.S.A. only)
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on page 49. If this operation manual does not answer your question, please call toll free 1-800-BE-SHARP
(1-800-237-4277) for further assistance. Or, send us an e-mail at lcdsupport@sharplcd.com .
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
Front and Top View
LAMP REPLACEMENT
MUTE button
17
16
47
indicator
TEMPERATURE WARNING
indicator
POWER indicator
47
17
16
17
POWER buttons (ON/OFF)
VOLUME buttons (
ם /מ ) KEYSTONE button
INPUT button
MENU button
19
17
33
34
19
23
23
25
29
36
35
23
IrCOM button
AUTO SYNC button
RESIZE button
GAMMA button
ENTER button
FREEZE button
ENLARGE button
UNDO button
ADJUSTMENT buttons
(∂/ƒ/ß / ©)
Speaker
Remote control sensor 21
Zoom ring
Focus ring
17
17
Cooling fan (Exhaust vent)
Foot releases
5
19
Side and Rear View
Cooling fan (Intake vent)
IrCOM sensor
25
11
49
13
Remote control sensor
21
AC socket
Kensington Security
Standard connector
INPUT 2 port
AUDIO INPUT terminals:
RCA
INPUT 1 port (HD 15)
11
11
14
12
12
12
VIDEO INPUT terminal:
RCA
AUDIO INPUT terminal
(3.5 mm stereo minijack)
RS-232C port
(9-pin mini-DIN)
S-VIDEO INPUT terminal:
4 pin mini DIN
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Remote Control
Front View
Rear View
MUTE button
17
POWER buttons
(ON/OFF)
16
17
VOLUME buttons
(
ם /מ ) 17
LEFT-CLICK/
UNDO
button
19
22
19
37
22
23
KEYSTONE/BLACK
SCREEN button
LASER POINTER/
MENU button
MOUSE/
ADJUSTMENT
buttons (∂/ƒ/ß/©)
RIGHT-CLICK/
ENTER button
22
23
22
23
INPUT button
FREEZE button
ENLARGE button
TOOLS button
IrCOM button
17
33
34
44
21
25
29
36
35
22
AUTO SYNC button
RESIZE button
GAMMA button
BACKLIGHT button
MOUSE/
ADJUSTMENT
switch
Top View
Remote control
signal transmitter
Laser
pointer
window
5
Inserting the batteries
Press in and downward
I
nsert two AA size batteries
Insert the side tabs of
the battery cover into
their slots and press the
cover in until it is
1
2
3
on the arrow to remove
for the remote control,
making sure their polarities
match the
and marks inside the battery
the battery cover.
properly seated.
compartment.
Battery
cover
Battery
cover
Battery
compartment
E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup & Connections
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Remote control
RRMCG1530CESA
Power cord
QACCU5013CEZZ
Two AA size batteries
Mouse control
serial cable
QCNW-5112CEZZ
Computer audio cable
QCNW-4870CEZZ
Computer cable
QCNW-5304CEZZ
Mouse control
cable for IBM PS/2
QCNW-5113CEZZ
Mouse control cable
for Mac
QCNW-5114CEZZ
DIN-D-sub RS-232C cable
QCNW-5288CEZZ
Remote mouse receiver
RUNTK0661CEZZ
Carrying bag
GCASN0003CESA
Lens cap
GCOVH1308CESA
Lens cap strap
UBNDT0012CEZZ
CD-ROM
UDSKA0009CE01
Sharp Advanced Presentation
Software operation manual
TINS-6888CEZZ
Projector operation manual
TINS-6786CEZZ
Sharp Advanced Presentation
Software quick reference
TINS-6788CEZZ
Projector quick reference
TINS-6787CEZZ
IrDA driver installation
instruction sheet
TCAUZ3046CEZZ
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Power cord
QACCU5013CEZZ
Connecting the Projector to a Computer
You can connect your projector to a computer for projection of full color computer images.
To a computer using the standard 15-pin (VGA) input
Computer cable
QCNW-5304CEZZ
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the supplied computer cable to
the INPUT 1 port on the projector.
2 Connect the other end to the Monitor output port on the
computer. Secure the connectors by tightening the
thumb screws.
3 To use the built-in audio system, connect one end of
the supplied computer audio cable to the AUDIO INPUT
terminal on the projector.
4 Connect the other end to the Audio output terminal on
the computer.
CAUTION
• Before connecting, be sure to turn both the projector and the
computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.
• Please read the computer’s operation manual carefully.
• Refer to pages 55 and 56 “Input Signals (Recommended
Timing)” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may
cause some of the functions not to work.
When connecting this projector to a computer, select
“Computer/RGB” for “Signal Type” on the GUI menu. (See
page 40.)
• A Macintosh adaptor may be required for use with some
Macintosh computers. Contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting other compatible computers
When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “Computer/RGB” for “Signal Type” on the GUI menu. (See page 40.)
• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT accepts INPUT 1 or 2 port input.
“Plug and Play” function
• This projector is compatible with VESA-standard DDC 1/DDC 2B when connecting to a 15-pin analog terminal
and VESA-standard DDC 2B when connecting to a 20-pin digital terminal. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.
• The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible
computer.
To a computer using the direct digital input (PanelLink™)
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the digital cable to the INPUT 2
port on the projector.
2 Connect the other end to the corresponding termi-
nal on a computer.
3 To use the built-in audio system, connect one and
of the supplied computer audio cable to AUDIO
INPUT terminal on the projector.
Connect the other end to the Audio output terminal
on the computer.
Digital cable (sold separately)
2To digital output terminal
Computer audio cable (3.5 mm stereo minijack cable)
Computer
To audio output terminal
E-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting the Projector to Video Equipment
You can connect your projector to a VCR, laser disc player, DVD player, DTV decoder and other audiovisual
equipment.
CAUTION
• Always turn off the projector while connecting to video equipment, in order to protect both the projector and the equipment
being connected.
To a video source (VCR, laser disc player, DTV decoder or DVD player) using the standard video input
1 Connect the yellow RCA connectors to the corresponding
yellow VIDEO INPUT terminal on the projector and the Video
output terminal on the video source.
2 To use the built-in audio system, connect the red and white
RCA connectors to the corresponding red and white AUDIO
INPUT terminals on the projector and the Audio output
terminals on the video source.
The S-VIDEO INPUT terminal uses a video signal system in which
the picture is separated into a color and a luminance signal to
realize a higher-quality image.
• For higher quality video, you may use the S-VIDEO INPUT terminal on
the projector. S-video cable is sold separately.
• If your video equipment does not have an S-video output terminal, use
the Composite video output terminal.
S-video cable (sold separately)
To S-video output terminal
VCR
1Video cable (sold separately)
To video output terminal
2Audio cable (sold separately)
To audio output terminals
or
Laser disc player
To a DTV decoder or DVD player
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the HD-15-RGB cable to the INPUT 1
port on the projector.
2 Connect the other end to the corresponding terminals on the
video source.
3 To use the built-in audio system, connect one end of the
supplied computer audio cable to AUDIO INPUT terminal on
the projector.
Connect the other end to the Audio output terminal on the
video source.
Select “Computer/RGB” or “Component” for “Signal Type” on
the GUI menu, depending on the video source.
HD-15-RGB cable (sold separately)
2To video input terminals
DTV decoder
or
DVD player
Computer audio cable (3.5 mm stereo minijack cable)
To audio output terminal
E-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting RS-232C Port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (cross type, sold
separately), the computer can be used to control the projector and check the status of the projector. See pages 53
and 54 for details.
Computer cable
QCNW-5304CEZZ
DIN-D-sub RS-232C
cable
QCNW-5288CEZZ
Computer audio cable
QCNW-4870CEZZ
1 Connect the supplied DIN-D-sub RS-232C cable to the RS-232C port on the projector.
2 Connect a RS-232C cable (sold separately) to the other end of DIN-D-sub RS-232C cable and to the serial
port on the computer.
2RS-232C cable
(cross type, sold separately)
1 DIN-D-sub
RS-232C cable
CAUTION
• Do not connect or remove RS-232C cable to or from the computer while it is on. This may damage your computer.
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set up. Please refer to the
operation manual of the computer for details on setting up/installing the correct mouse driver.
• The arrows (→, ↔) indicate the direction of the signals.
E-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting the Remote Mouse Receiver
• You can use the remote control as a remote mouse.
• When the RS-232C port on the projector is connected to a computer with
an RS-232C cable (cross type, sold separately), the computer can be
used to control the projector and check the status of the projector. See
pages 53 and 54 for details.
IBM or IBM compatible PC
1 Connect one end of the supplied mouse control cable to the corresponding terminal on the PC.
2 Connect the other end to the remote mouse receiver.
or
Remote mouse
receiver
RUNTK0661CEZZ
Mouse control
serial cable
QCNW-5112CEZZ
Mouse control cable
for IBM PS/2
QCNW-5113CEZZ
IBM PC/AT
IBM PS/2
Remote mouse receiver
Use this terminal to con-
nect the supplied
mouse control cable to
the remote mouse
receiver.
Mouse control cable
for Mac
QCNW-5114CEZZ
Mouse control
serial cable
QCNW-5112CEZZ
Macintosh
1 Connect the mouse control serial cable to the remote mouse receiver.
2 Connect the mouse control cable for Mac to the Mac ADB port on the Mac.
3 Connect the other end of the mouse control cable for Mac to the mouse control serial cable.
CAUTION
• Do not connect or remove the mouse control cables to or from the computer while it is on. This may damage your computer.
• The wireless mouse functions can operate computers compatible with IBM PS/2, serial (RS-232C) or Apple ADB type
mouse systems.
E-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Basic Operations
1 Make the necessary connections before pro-
ceeding. Connect the power cord to a wall outlet.
The POWER indicator lights up red and the
projector enters standby mode.
2 Press Power ON.
2
• The flashing green LAMP REPLACEMENT indicator shows
that the lamp is warming up. Wait until the indicator stops
flashing before operating the projector.
• If the power is turned off and then immediately turned on
again, it may take a short while before the lamp turns on.
• After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust vent.
This odor will soon disappear with use.
When the power is on, the LAMP REPLACEMENT
indicator lights indicating the status of the lamp.
Green: Lamp is ready.
Flashing green: Warming up.
Red: Change the lamp.
E-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
3 Rotate the focus ring until the image on the screen
becomes clear.
4
3
4 Rotate the zoom ring. The image can be adjusted
to the desired size within the zoom range.
6
7
8
5
5 Press INPUT to select the desired input mode.
EXAMPLE
Press INPUT again to change the mode.
INPUT 1 Mode
INPUT 2 Mode
VIDEO Mode
5
• When no signal is being received, “NO SIGNAL” will be
displayed. When a signal that the projector is not preset
to receive is being received, “NOT REG.” will be displayed.
f
f
6 Press VOLUME
/ to adjust the volume. 6
7
8
7 Press MUTE to temporarily turn off the sound.
Press MUTE again to turn the sound back on.
8 Press POWER OFF.
Press POWER OFF again while the message is
displayed.
• If you accidentally pressed POWER OFF and do not want
to turn off the power, wait until the power off screen
disappears.
• When POWER OFF is pressed twice, the POWER indicator
will light up red and the cooling fan will run for about 90
seconds. The projector will then enter standby mode.
• Wait until the cooling fan stops before disconnecting the
power cord.
• The power can be turned on again by pressing POWER
ON. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light green.
E-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
• The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colors, making viewing
difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according
to the desired picture size (see the table below).
X
L
H
NORMAL Mode
(4:3)
Picture size
Projection distance
Distance from the lens center to the
bottom of the image (H)
Diag.
300Љ
200Љ
150Љ
100Љ
84Љ
72Љ
60Љ
40Љ
Width
240Љ
160Љ
120Љ
80Љ
67Љ
58Љ
48Љ
32Љ
Height
180Љ
120Љ
90Љ
60Љ
50Љ
43Љ
36Љ
24Љ
Maximum
Minimum
40Ј (12.2 m)
26Ј 8Љ (8.1 m)
19Ј 11Љ (6.1 m)
13Ј 3Љ (4.0 m)
11Ј 1Љ (3.4 m)
9Ј 6Љ (2.9 m)
7Ј 10Љ (2.4 m)
5Ј 2Љ (1.6 m)
—
35 1⁄32Љ (89.0 cm)
23 11⁄32Љ (59.3 cm)
17 33⁄64Љ (44.5 cm)
11 11⁄16Љ (29.7 cm)
9 49⁄64Љ (24.8 cm)
8 25⁄64Љ (21.3 cm)
7 1⁄64Љ (17.8 cm)
4 11⁄16Љ (11.9 cm)
32Ј (9.8 m)
23Ј 11Љ (7.3 m)
15Ј 11Љ (4.9 m)
13Ј 4Љ (4.1 m)
11Ј 5Љ (3.5 m)
9Ј 6Љ (2.9 m)
6Ј 3Љ (1.9 m)
The formula for picture size and projection distance
y = (0.049x
מ 0.0508) ן 3.28 y1 = (0.0408x
מ 0.049) ן 3.28 y23 = 0.297x
x: Picture size (diag.) (inches)
y : Maximum projection distance (feet)
y1 : Minimum projection distance (feet)
y32 : Distance from the lens center to the
bottom of the image (H) (inches)
• There is an error of
ע 3% in the formula above. Picture size
Projection distance
WIDE Mode
(16:9)
Distance from the lens center to the
bottom of the image (H)
Diag.
300Љ
200Љ
150Љ
133Љ
106Љ
100Љ
92Љ
84Љ
72Љ
60Љ
40Љ
Width
261Љ
174Љ
131Љ
116Љ
92Љ
87Љ
80Љ
73Љ
63Љ
Height
147Љ
98Љ
74Љ
65Љ
52Љ
49Љ
45Љ
41Љ
Maximum
—
Minimum
43Ј 6Љ (13.3 m)
28Ј 11Љ (8.8 m)
21Ј 8Љ (6.6 m)
19Ј 2Љ (5.9 m)
15Ј 3Љ (4.7 m)
14Ј 5Љ (4.4 m)
13Ј 3Љ (4.0 m)
12Ј 1Љ (3.7 m)
10Ј 4Љ (3.1 m)
8Ј 7Љ (2.6 m)
5Ј 8Љ (1.7 m)
38 9⁄64Љ (96.9 cm)
25 7⁄16Љ (64.6 cm)
19 5⁄64Љ (48.4 cm)
16 29⁄32Љ (43.0 cm)
13 31⁄64Љ (34.2 cm)
12 23⁄32Љ (32.3 cm)
11 45⁄64Љ (29.7 cm)
10 11⁄16Љ (27.1 cm)
9 5⁄32Љ (23.3 cm)
7 5⁄8Љ (19.4 cm)
34Ј 9Љ (10.6 m)
26Ј (7.9 m)
23Ј 1Љ (7.0 m)
18Ј 4Љ (5.6 m)
17Ј 4Љ (5.3 m)
15Ј 11Љ (4.9 m)
14Ј 6Љ (4.4 m)
12Ј 5Љ (3.8 m)
10Ј 4Љ (3.1 m)
6Ј 10Љ (2.1 m)
35Љ
29Љ
20Љ
52Љ
35Љ
5 3⁄32Љ (12.9 cm)
The formula for picture size and projection distance
y = (0.0533x
מ 0.0552) ן 3.28 y1 = (0.0444x
מ 0.0533) ן 3.28 y23 = 0.323x
x: Picture size (diag.) (inches)
y : Maximum projection distance (feet)
y1 : Minimum projection distance (feet)
y23 : Distance from the lens center to the
bottom of the image (H) (inches)
• There is an error of
ע 3% in the formula above. E-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Using the Adjustment Feet
There are two front adjustment feet and a rear adjustment foot.
To lower the position of the picture, pull out the folded leg of the rear adjustment foot.
See the diagram shown below for using the front adjustment feet.
1
2
3
Press foot releases.
Adjust height of projector
and remove hands from foot
releases.
Rotate feet to make minor
changes.
• The projector is adjustable up to approximately 5° from the standard position.
• When the height of the projector is adjusted, the image may become distorted (keystoned), depending on the relative positions of the
projector and the screen.
CAUTION
• Do not press the foot releases when the adjustment feet are extended without firmly holding the projector.
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the projector.
Digital Keystone Correction
Projector
Remote control
When the image is distorted due to the projection angle,
the Digital Keystone Correction function allows you to
correct it.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 5
1 Press KEYSTONE.
2
3, 4
6
2 Press ∂ to compress the upper part of the image.
Press ƒ to compress the lower part of the image.
3 Press ENTER to display a test pattern.
4 Press ENTER to clear the test pattern.
5 To exit, press KEYSTONE.
Pressing ∂
in Step 2
Pressing ƒ
in Step 2
6 To reset, press UNDO.
• Straight lines or the edges of the displayed image may
become jagged.
On-screen Display
3 Test Pattern
4
g
E-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Reversed Image Setup
Rear projection
Projection using a mirror
• Place a translucent screen between the projector and
the audience.
• Place a mirror (normal flat type) in front of the lens.
• Use the projector’s menu system to reverse the
projected image. (See page 43 for use of this
function.)
• Use the projector’s menu system to reverse the
projected image. (See page 43 for use of this
function.)
• The image reflected from the mirror is projected onto
the screen.
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
CAUTION
• When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount Setup
• It is recommended that you use the optional Sharp
ceiling-mount bracket for this installation.
• Before mounting the projector, contact your nearest
Authorized Sharp Industrial LCD Products Dealer or
Service Center to obtain the recommended ceiling-
mount bracket (sold separately). (AN-NV7T ceiling-
mount bracket, AN-TK201/202 extension tube for AN-
NV7T.)
• When the projector is in the inverted position, use the
upper edge of the screen as the base line.
• Use the projector’s menu system to select the
appropriate projection mode. (See page 43 for use
of this function.)
E-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Wireless Mouse from the Remote Control
Using the Remote Control as a Wireless Mouse
The remote control has the following three functions:
• Projector control
MOUSE/ADJUSTMENT switch
(Remote control)
• Wireless mouse
• Laser pointer
MOUSE
ADJ.
MOUSE
ADJ.
Wireless mouse
Laser pointer
Projector control
Remote Control/Mouse Receiver Positioning
• The remote control can be used to control the projector within the ranges shown below.
• The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.
Controlling the Projector
Using the Wireless Mouse
Remote control
Remote control
23Ј (7 m)
30˚
30˚
30˚
45˚
30˚
120˚
13Ј(4 m)
Remote
45˚
mouse
receiver
30˚
Remote control
E-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Wireless Mouse from the Remote Control
Use as a Wireless Mouse
Be sure the supplied remote mouse receiver is connected to your computer.
MOUSE
ADJ.
Slide the MOUSE/ADJUSTMENT switch to MOUSE.
Effective buttons in MOUSE mode
1
LASER
BLACK SCREEN
POINTER
LEFT-CLICK
MOUSE
RIGHT-CLICK
• The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer
to the computer’s operation manual for details of setting up/installing the mouse driver.
• For one-button mouse systems, use either the LEFT-CLICK or RIGHT-CLICK button.
Using the remote control in a dark room
Press BACKLIGHT, and the buttons will light up. Green lights refer to mouse operations, and red
lights to projector adjustments.
Button name
Button name
Position of MOUSE/ADJUSTMENT switch
MOUSE ADJ.
Position of MOUSE/ADJUSTMENT switch
MOUSE ADJ.
LASER POINTER/MENU LASER POINTER (GREEN) MENU (RED)
BLACK SCREEN/KEYSTONE BLACK SCREEN (GREEN) KEYSTONE (RED)
INPUT
IrCOM
RIGHT-CLICK/ENTER
RIGHT-CLICK (GREEN)
ENTER (RED)
FREEZE
AUTO SYNC
ENLARGE
RESIZE
MOUSE/ADJUSTMENT MOUSE (NOT LIT)
ADJUSTMENT (NOT LIT)
UNDO (NOT LIT)
ON (RED)
LEFT-CLICK/UNDO
POWER ON/OFF
VOLUME
ם /מ MUTE
LEFT-CLICK (NOT LIT)
ON (RED)
TOOLS
GAMMA
Use as a Laser pointer
MOUSE
ADJ.
Slide the MOUSE/ADJUSTMENT switch to MOUSE.
1
2
Press LASER POINTER ( ) to activate the laser pointer.
When the button is released, the light automatically goes off.
• For safety, the laser pointer automatically goes off after 1 minute of continuous use. To turn it on,
release LASER POINTER ( ) and press again.
E-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the GUI (Graphical User Interface) Menu Screens
Projector
Remote control
1, 7
2, 3, 5
4
6
This projector has two sets of menu screens (INPUT/VIDEO) that allow you to adjust the image and various projector
settings. These menu screens can be operated from the projector or the remote control with the following buttons.
(GUI) On-screen Display
INPUT (COMPUTER/RGB) mode
VIDEO mode
1
1
ß 2©
ß 2©
∂
∂
3
ƒ
3
ƒ
ß 5©
ß 5©
4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
ß 2©
1 Press MENU to display the INPUT or VIDEO mode
menu bar.
2 Press ß/© to select an adjustment menu on the
menu bar.
ß 5©
3 Press ∂/ƒ to select a specific adjustment item.
4 To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5 Press ß/© to adjust the item.
6 Press UNDO to return to the previous screen.
7 Press MENU to exit from the GUI.
• For details on items on the menu screen, see the tree charts
on the next page.
E-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the GUI (Graphical User Interface) Menu Screens
Items on the INPUT1 or INPUT2 Mode Menu Bar Items on the VIDEO Mode Menu Bar
Main menu
Sub menu
Main menu
Sub menu
Picture
Contrast
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 Picture
Contrast
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 Bright
Color
Tint
Bright
Color
Tint
Sharp
Red
Sharp
Red
Blue
Blue
Resolution
800
ן 600 640
ן 480 Vert Freq
75 Hz
72 Hz
1
Reset
Auto Sync
Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Reset
Treble
Bass
2
•
מ 30 ם 30 Fine Sync
[ON/OFF]
מ 150 ם 150 מ 60 ם 60 מ 150 ם 150 מ 60 ם 60 Audio
•
מ 30 ם 30 7
Reset
Lamp Timer
Resolution
800
ן 600 640
ן 480 Vert Freq
75 Hz
72 Hz
1
Options
2
•
BLK SCRN Disp [ON/OFF]
OSD Display [ON/OFF]
•
7
Auto Power Off [ON/OFF]
I/P Conversion
1152
ן 864 1024
ן 864 1152
ן 882 1152
ן 870 Select Setting
Special Modes
Interlaced
Progressive
Treble
מ 30 ם 30 מ 30 ם 30 Audio
Video System
Auto
Bass
PAL (50 /60Hz)
SECAM
Reset
Options
Lamp Timer
NTSC4.43
NTSC3.58
Auto Sync Disp [ON/OFF]
BLK SCRN Disp [ON/OFF]
Background
Sharp
Custom
Blue
OSD Display
Auto Power Off
I/P Conversion
Signal Type
Background
Startup Image
Signal Info
English
[ON/OFF]
[ON/OFF]
Interlaced
Progressive
None
Computer/RGB
Component
Startup Image
English
Sharp
Custom
None
Language
Sharp
Custom
Blue
Deutsch
Español
Language
Nederlands
Français
Italiano
Deutsch
None
Español
Sharp
Custom
None
Nederlands
Français
Svenska
Português
Italiano
Resolution 640
ן 480 Svenska
Hor Freq
Vert Freq
37.5 kHz
72 Hz
Português
Front
PRJ Mode
Ceiling
ם Front Rear
Front
PRJ Mode
Ceiling
ם Rear Ceiling
ם Front Rear
Status
Ceiling
ם Rear Status
• The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
• “Color”, “Tint”, and “Sharp” appear only when Component input is selected in INPUT 1 mode.
• Only the items highlighted in the tree charts above can be adjusted.
• To adjust the items under the sub menu, press © after selecting the sub menu.
• The signal is set to COMPUTER/RGB, when inputting DIGITAL signal.
• The items displayed in gray cannot be adjusted.
E-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using IrCOM for Wireless Presentations
Projector
Remote control
The IrCOM function can transfer still images from a
computer or digital camera to the projector via infrared
(wireless) communication.
Sharp Advanced Presentation Software
• This function requires the supplied Sharp Advanced
Presentation Software (SAPS).
• Install the SAPS in the supplied CD-ROM on the
computer.
1, 2
• See the operation manual of the software for
installation and operating instructions.
3
• Position the projector and the IrCOM transmitting
device within the range shown on the left.
PC
• To avoid transmission errors or changes in the image, ensure
the following when setting up the projector and transmitting
device.
Digital camera
• The IrCOM sensors on both the projector and transmitting
device are protected from direct sunlight or strong
ambient light.
15˚
4؆ (10 cm)–3ꢀ 3؆ (1 m)
15˚
• The transmitting device has sufficient battery power.
• The projector and transmitting device are positioned
within the designated operating range.
• The IrCOM sensors on the projector and transmitting
device are correctly aligned.
15˚
15˚
• The distance between the projector and transmitting device
may have to be less than 4Љ (10 cm) depending on the
transmitting device.
• When using the digital still camera, set it to the image
transmission mode.
• Align the projector and transmitting device at the same
height and angle at a distance of 4Љ (10 cm) to 3Ј 3Љ (1 meter)
with an unobstructed line of view.
On-screen Display
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press IrCOM to enter the IrCOM mode.
2 And then the On-screen Display changes as
shown on the left.
• If the On-screen Display does not change as shown on the
left, the projector may not be within the reception range
from the IrCOM transmitting device.
f
f
3 Press INPUT to exit the IrCOM mode.
E-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the On-screen Display Language
English is the preset language for the On-screen
Display. It can be changed to English, German, Spanish,
Dutch, French, Italian, Swedish, Portuguese, Chinese,
Korean or Japanese.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 5
1 Press MENU.
2, 3
2 Press ß/© to select “Language”.
4
3 Press ∂/ƒ to select the desired language .
4 Press ENTER to save the setting. The On-screen
Display is now programed to display in the
language selected.
(GUI) On-screen Display
5 To exit from the GUI, press MENU.
Selecting the Video Input System Mode (VIDEO mode only)
Projector
Remote control
The video input system mode is preset to “Auto”;
however, it can be changed to a specific system mode,
if the selected system mode is not compatible with the
connected audiovisual equipment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
2, 3, 4
1 Press MENU.
5
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Video System”, and then
press ©.
4 Press ∂/ƒ to select the desired video system
(GUI) On-screen Display
mode.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• When the system mode is set to “Auto”, you may not receive
a clear picture due to signal differences. Should this occur,
switch to the video system you are viewing.
E-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
You can adjust the projector’s picture to your prefer-
ences with the following picture settings.
Projector
Remote control
Description of Adjustment Items
ß button
© button
Selected item
1, 4
Contrast
Bright
Color
Tint
For less contrast
For less brightness
For less color intensity
For more contrast
For more brightness
For more color intensity
2, 3
Skin tones become purplish Skin tones become greenish
Sharp
Red
For less sharpness
For weaker red
For more sharpness
For stronger red
Blue
Reset
For weaker blue
All image adjustment items are returned to the factory preset
settings.
For stronger blue
(GUI) On-screen Display
(COMPUTER/RGB input in INPUT mode)
• “Color”, “Tint” and “Sharp” do not appear for COMPUTER/
RGB input in INPUT 1 mode.
1
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ∂/ƒ to select a specific adjustment item.
3 Press ß/© to move the mark of the selected
2
adjustment item to the desired setting.
4 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Picture”
menu screen and press ENTER.
• The adjustments can be stored separately in the “INPUT 1”,
“INPUT 2” and “VIDEO” modes.
• For COMPONENT input in INPUT 1 mode, “Sharp” is
adjustable only when a DVD player is connected.
• When adjusting the items under the “Picture” menu in
DIGITAL input, the changes affect both the picture being
viewed and the GUI menu screen.
E-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Projector
Remote control
This projector’s audio is factory preset to standard
settings. However, you can adjust it to suit your own
preferences by adjusting the following audio settings.
Description of Adjustment Items
Selected item
ß button
© button
1, 5
Treble
Bass
Reset
For weaker treble
For weaker bass
All audio adjustment items are returned to the factory preset
settings.
For stronger treble
For stronger bass
2, 3, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
2
3
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ß/© to select “Audio”.
3 Press ∂/ƒ to select a specific adjustment item.
4 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Audio”
menu screen and press ENTER.
E-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments
When displaying computer patterns which are very
Projector
Remote control
detailed (tiling, vertical stripes, etc.), interference may
occur, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur,
adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for
optimum computer image.
1, 5
2, 3, 4
Description of Adjustment Items
Selected item
Description
Clock
Phase
H-Pos
V-Pos
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
• Computer image adjustment can be made easily by
pressing AUTO SYNC ( ). See the next page for details.
(GUI) On-Screen Display
(Select the desired computer input mode with INPUT.)
2
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ß/© to select “Fine Sync”.
3
3 Press ∂/ƒ to select a specific adjustment item.
4 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Fine
Sync” menu screen and press ENTER.
• When inputting DIGITAL signal, the projector automatically
selects the settings for the best possible picture. You do
not need to adjust any settings.
E-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments
Projector
Remote control
Auto Sync Adjustment
• Used to automatically adjust a computer image.
• Auto Sync adjustment can be made manually by
pressing AUTO SYNC, or automatically by setting
“Auto Sync” to “ON” in the projector’s GUI menu.
1, 5
When “Auto Sync” is set to “ON”:
• The sync adjustment is automatically made each time
the projector is turned on while connected to a com-
puter or the input selection is changed.
2, 3, 4
• The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
AUTO SYNC
button
(Slide the MOUSE/ADJUSTMENT switch
MOUSE
ADJ.
on the remote control to the ADJ. position.)
1 Press MENU.
(GUI) On-screen Display
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Auto Sync”.
4 Press ß/© to select “ON”.
5 To exit from the GUI, press MENU.
• Automatic adjustments can be made by pressing AUTO
SYNC.
• When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See the
previous page.)
On-screen Display
• When inputting DIGITAL signal, the projector automatically
selects the settings for the best possible picture. You do
not need to adjust any settings.
g
During Auto Sync adjustment, the On-screen Display
changes as shown on the left.
f
• Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
s
Auto Sync Display Function
Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a background image during Auto Sync
adjustment.
(GUI) On-screen Display
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
2 Press ß /© to select “Options”.
3 Press ∂/ƒ to select “Auto Sync Disp”.
4 Press ß /© to select “ ” to superimpose a
background image or “ ” to remove the
background image during Auto Sync adjustment.
5 To exit from the GUI, press MENU.
E-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments
Projector
Remote control
Saving and Selecting Adjustment Settings
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect the computer to the projector.
1, 6
Saving the adjustment setting
2, 3, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
5
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
(GUI) On-screen Display
2
3 Press ∂/ƒ to select “Save Setting”, and then press
©.
4 Press ∂/ƒ to select the desired memory location of
the setting.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
3
Selecting a saved setting
MOUSE
ADJ.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Select Setting”, and then press
©.
4
4 Press ∂/ƒ to select the desired memory setting.
5 Press ENTER to select the setting.
6 To exit from the GUI, press MENU.
• If the memory position has not been set, the resolution and
frequency will not be displayed.
• When selecting the stored adjustment setting with “Select
Setting”, the computer system should match the stored
setting.
• This function cannot be used when inputting DIGITAL signal.
E-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments
Projector
Remote control
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, “Special Modes” on the “Fine
Sync” menu screen may need to be changed to match
the computer display mode.
1, 6
(Slide the MOUSE/ADJUSTMENT switch on
the remote control to the ADJ. position.)
MOUSE
ADJ.
2, 3, 4
5
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Special Modes”, and then
(GUI) On-screen Display
press ©.
4 Press ∂/ƒ to select the optimal resolution mode.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• Avoid displaying computer patterns which repeat every
other line (horizontal stripes). (Flickering may occur, making
the image hard to see.)
• When inputting DTV 480P signals, select “480P” in step 4
above.
E-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Features
Freeze Function
Projector
Remote control
This function allows you to instantly freeze a moving
image. This is useful when you want to display a still
image from a computer or video, giving you more time
to explain the image to the audience.
You can also use this function to display a still image
from a computer while you make preparations for the
next computer images to be presented.
1 Press FREEZE to freeze the image.
1, 2
2 Press FREEZE again to return to the moving
image.
On-screen Display
E-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Image Magnification (ENLARGE)
Projector
Remote control
2
1
3
On-screen Display
This function allows you to magnify a specific portion of
an image. This is useful when you want to display a
detailed portion of the image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ.)
MOUSE
ADJ.
1 Press ENLARGE. Each time ENLARGE is
pressed, the image will be magnified.
2 When the image is magnified, you can pan and
scan around the image by using ∂/ƒ/ß/©.
• Each time ENLARGE is pressed, image magnification
toggles as shown below.
1 2 3 4 6 8 • If the input signal is changed during digital image
magnification, the image will return to
ן 1. The input signal is changed
(a) when INPUT is pressed,
(b) when the input signal is interrupted, or
(c) when the input resolution and refresh rate changes.
3 To return to
ן 1, press UNDO. E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Gamma Correction
Projector
Remote control
2
1
• Gamma is an image quality enhancement function
that offers a richer image by brightening the darker
portions of the image without altering the brightness
of the brighter portions.
On-screen Display
STANDARD
• Four gamma settings are available to allow for
differences in the images displayed and in the
brightness of the room.
• When you are displaying images with frequent, dark
scenes, such as a film or concert, or when you are
displaying images in a bright room, this feature makes
the dark scenes easier to see and gives the impres-
sion of greater depth in the image.
GAMMA 1
GAMMA 2
CUSTOM
Gamma Modes
Selected Mode Gamma mode
STANDARD
GAMMA 1
Standard picture without gamma correction.
Brightens darker portions of image for more
enhanced presentations.
GAMMA 2
CUSTOM
Gives greater depth to darker portions of image
for a more exciting theater experience.
Allows you to adjust gamma value using Sharp
Advanced Presentation Software.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press GAMMA. Each time GAMMA is pressed,
the gamma level toggles as shown on the left.
2 To return to the standard image, press UNDO
while “GAMMA” is displayed on the screen.
E-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Picture Display Mode
This function allows you to modify or customize the picture display mode to enhance the input image. Depending
on the input signal, you can choose NORMAL, WIDE, DOT BY DOT, DOT BY DOT (WIDE), or FIT TO SCREEN
image.
• Each time RESIZE is pressed, the picture mode changes as shown below.
• “FIT TO SCREEN” is displayed only when SXGA signals that are not in 4:3 aspect ratio are input.
• DOT BY DOT mode displays images in their native resolution and not expanded to fit the LCD resolution.
• To return to NORMAL mode, press UNDO while “RESIZE” is displayed on the screen.
Projector
Remote control
EXAMPLE
DTV
COMPUTER
SXGA
MODE
4:3
16:9
INPUT SIGNAL
480 P
720 P
NORMAL
WIDE
DOT BY DOT
1024
ן 768 1024
ן 576 640
ן 480 853
ן 480 1024
ן 576 960
ן 768 1024
ן 768 1280
ן 1024 —
—
1280
ן 720 —
(
)
DOT BY DOT WIDE
RESIZE
button
NORMAL
WIDE
DOT BY DOT
DOT BY DOT (WIDE)
For DTV decoder RGB signal in 4:3 aspect ratio.
g
g
g
For DTV decoder RGB signal in 16:9 aspect ratio.
For COMPUTER/RGB signal without 4:3 aspect ratio.
g
g
E-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Screen Function
Projector
Remote control
This function can be used to superimpose a black
screen over the projected image.
BLACK
SCREEN
button
Blacking out the Projected Image
Press BLACK SCREEN. “BLACK SCREEN” is dis-
played on the screen. To return to the original projected
image, press BLACK SCREEN again.
1, 5
2, 3, 4
MOUSE
ADJ.
• To use the remote control to operate this
function, slide the MOUSE/ADJUSTMENT switch to the
MOUSE position before pressing BLACK SCREEN.
Projected Image
Turning off the On-screen Display
The On-screen Display (“BLACK SCREEN”) that
appears during black screen can be turned off. When
“BLK SCRN Disp” is set to “ ” in the GUI menu, “BLACK
SCREEN” will not be displayed during function.
sg
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
(GUI) On-screen Display
2 Press ß /© to select “Options”.
3 Press ∂/ƒ to select “BLK SCRN Disp”.
4 Press ß/© to select “ ” to turn on or “ ” to
turn off the function.
5 To exit from the GUI, press MENU.
On-screen Display Override Function
Projector
Remote control
This function allows you to turn off the on-screen
messages that appear during “input select” and the
“IrCOM” function. Once “OSD Display” is set to “ ” in
the GUI menu, the on-screen messages will not appear
when INPUT and IrCOM are pressed.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1, 5
MOUSE
ADJ.
2, 3, 4
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “OSD Display”.
(GUI) On-screen Display
4 Press ß/© to select “ ” to turn on or “ ” to turn
off the On-screen Display.
5 To exit from the GUI, press MENU.
E-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Power Shutoff Function
When no input signal is detected for more than 15
minutes, the projector will automatically shut off.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
1 Press MENU.
2, 3, 4
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Auto Power Off”.
4 Press ß/© to select the “ ” or “ ”.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
5
(GUI) On-screen Display
On-screen Display
• The on-screen message on the left will appear five minutes
before the power is automatically turned off.
E-38
Download from Www.Somanuals.com. All Manuals Search And Download.
I/P Conversion
Projector
Remote control
This function allows you to select either an interlaced
display or a progressive display of a video signal. The
progressive display projects a smoother video image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
1 Press MENU.
2, 3, 4
2 Press ß/© to select “Options”.
5
3 Press ∂/ƒ to select “I/P Conversion”, and then
press ©.
(GUI) On-screen Display
4 Press ∂/ƒ to select “Interlaced” or “Progressive”.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
Interlaced mode
Interlaced mode creates a single image throught the activation
of scanning lines in two fields. Use this mode when projecting
moving images.
Progressive mode
Progressive mode creates a single image using all available
scanning lines, thereby eliminating the flicker and stripes that
result from interlaced source images projected as still images.
Checking the Lamp UsageTime
Projector
Remote control
This function allows you to check the accumulated lamp
usage time.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1
2
1 Press MENU.
2 Press ß/© to select “Options”. The lamp usage
time will be displayed.
• It is recommended that the lamp be replaced after
approximately 1,400 hours of usage. See pages 48 and 49
for lamp replacement.
(GUI) On-screen Display
E-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Signal Type
Projector
Remote control
This function allows you to select the input signal type
(COMPUTER/RGB or COMPONENT) for INPUT 1 port.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
1 Press MENU.
2, 3, 4
2 Press ß/© to select “Options”.
5
3 Press ∂/ƒ to select “Signal Type”, and then
press ©.
4 Press ∂/ƒ to select “Computer/RGB” or
(GUI) On-screen Display
“Component”.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
Checking the Input Signal
This function allows you to check the current input signal
information.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 4
1 Press MENU.
2, 3
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Signal Info” to display the
current input signal.
4 To exit from the GUI, press MENU.
(GUI) On-screen Display
• In VIDEO mode, the resolution and frequency settings will
not be displayed.
E-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a Background Image
This function allows you to select the image displayed
when no signal is being sent to the projector.
Projector
Remote control
Description of Background Images
Selected item
Sharp
Background image
1, 6
SHARP default image
User customized image (i.e. company logo)
Blue screen
Custom
Blue
2, 3, 4
None
Black screen
5
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Background”, and then press
©.
4 Press ∂/ƒ to select the background image you want
to display on the screen.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• By selecting “Custom”, the projector can display a custom
image (i.e. your company logo) as the background image.
Custom image must be 256-color BMP file with a picture
size of 1,024
ן 768 or lower. Please see the Sharp Advanced Presentation Software operation manual for how
to save (or change) a custom image.
E-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Startup Image
Projector
Remote control
• This function allows you to specify the image to be
displayed upon the projector’s startup.
• A custom image (i.e. your company logo) can be
loaded on the projector via IrCOM or an RS-232C
cable. See pages 14 and 25 in this operation manual,
and also the supplied Sharp Advanced Presentation
Software operation manual for detailed instructions.
1, 6
2, 3, 4
Description of Startup Images
Selected item
Sharp
Startup image
5
SHARP default image
User customized image (i.e. company logo)
Black screen
Custom
None
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Startup Image”, and then press
©.
4 Press ∂/ƒ to select the startup image you want to
display on the screen.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• By selecting “Custom”, the projector can display a custom
image (i.e. your company logo) as the startup image.
Custom image must be 256-color BMP file with a picture
size of 1,024
ן 768 or lower. Please see the Sharp Advanced Presentation Software operation manual for how
to save (or change) a custom image.
E-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Reverse/Invert Image Function
Projector
Remote control
This projector is equipped with a reverse/invert image
function which allows you to reverse or invert the pro-
jected image for various applications.
Description of Projected Images
1, 5
Selected item
Projected image
Front
Normal image
2, 3
Ceiling
ם Front Rear
Inverted image
Reversed image
4
Ceiling
ם Rear Reversed and inverted image
(GUI) On-screen Display
When Selecting “Front”
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
2 Press ß/© to select “PRJ Mode”.
3 Press ∂/ƒ to select the desired projection mode.
4 Press ENTER to save the setting.
When Selecting “Ceiling
ם Front” 5 To exit from the GUI, press MENU.
• This function is used for the reversed image and ceiling-
mount setups. See page 20 for these setups.
When Selecting “Rear”
When Selecting “Ceiling
ם Rear” E-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Presentation Tools
Projector
Remote control
2, 4
3, 5
6
1
On-screen Display
Menu Window
This projector is equipped with presentation tools. These
will help you emphasize keypoints within your
presentation.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press TOOLS to display the presentation tools
menu window on the screen.
2 Press ∂/ƒ/ß/© to select the desired tool and
color.
3 Press ENTER to select it.
4 Once the tool is displayed on the screen, press
∂/ƒ/ß/© to move it around the screen.
5 Press ENTER to stamp the tool on the screen.
Red
Green
Blue
Yellow
Orange
White
Black
6 Use UNDO to individually delete tools stamped
Projector
Remote control
on the screen.
• You can stamp each tool as many times as you want on the
screen.
2, 4
• To clear all the stamped presentation tools on the screen,
press ∂/ƒ/ß/© to select “ ” and ENTER.
3
1
Displaying the break time
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press TOOLS to display the presentation tools
When selecting Sharp default image
menu window on the screen.
2 Press ∂/ƒ/ß/© to select “ ” in the menu
window.
3 Press ENTER to start counting down the break
time.
4 Press ∂ to increase or ƒ to decrease the break
time.
• The break time is displayed against the background image
selected in “Selecting a Startup Image”. (See page 42.)
E-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Function
This function can be used to display all the adjusted
settings on the screen simultaneously.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
1, 4
2
2 Press ß/© to select “Status”.
3 Press ENTER to display all the adjusted settings.
3
4 To exit from the GUI, press MENU.
(GUI) On-screen Display
2
3
E-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance &
Troubleshooting
E-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp/Maintenance Indicators
Maintenance Indicators
• The warning lights on the projector indicate problems
inside the projector.
• There are two warning lights: a TEMPERATURE
WARNING indicator which warns that the projector is
too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicator will light up red. After turning off the power,
follow the procedures given below.
LAMP
REPLACEMENT
indicator
TEMPERATURE
WARNING
indicator
Maintenance Indicator
Condition
Problem
Possible Solution
• Blocked air intake.
• Relocate the projector to an area with
proper ventilation.
TEMPERATURE
WARNING indicator
The internal
temperature is
abnormally high.
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
LAMP REPLACE-
MENT indicator
The lamp does
not light up.
• Burnt-out lamp.
• Lamp circuit failure.
• Carefully replace the lamp. (See pages 48
and 49.)
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has
cooled down completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be
triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and put it back
in again.
Lamp
The lamp in this projector operates for approximately 1,500 cumulative hours, depending on the usage environ-
ment. It is recommended that the lamp be replaced after 1,400 cumulative hours of use or when you notice a
significant deterioration of the picture and color quality. The lamp usage time can be checked with the On-screen
Display (see page 39).
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
• As the usage environment can vary significantly, the projector lamp may not operate for 1,500 hours.
E-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Projection Lamp
It is recommended that the lamp be replaced after approximately 1,500 cumulative hours of use or when you
notice a significant deterioration of the picture and color quality. Carefully change the lamp by following the steps
below.
If the new lamp does not light after replacement, take your projector to the nearest Authorized Sharp Industrial
LCD Products Dealer or Service Center for repair. Purchase a replacement lamp unit (lamp/cage module) of the
current type BQC-XGNV7XU/1 from your nearest Authorized Sharp Industrial LCD Products Dealer or Service
Center. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp
replaced at your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through an Authorized Sharp Industrial LCD
Products Dealer or Service Center. For the name of the nearest Authorized Sharp Industrial LCD Products Dealer or
Service Center, please call toll-free: 1-800-BE-SHARP (1-800-237-4277).
U.S.A. ONLY
Removing and installing the lamp unit
CAUTION
• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely hot. Wait at least one
hour after the power cord is disconnected to allow the surface of the lamp cage to fully cool before removing the lamp
cage.
• Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of
the projector.
• To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
Turn off the power.
Disconnect the power
cord.
Slide the lamp cage
cover out.
1
2
3
Press POWER OFF. Wait until
the cooling fan stops.
Unplug the power cord from the
AC socket.
Turn over the projector and un-
fasten the user service screw
that secures the lamp cage
cover. Then slide the cover in the
direction of the arrow.
or
User service screw
Remove the lamp
cage.
Replace the lamp cage
(after changing the lamp).
Slide the lamp cage
cover in.
4
5
6
Remove the securing screws
from the lamp cage. Hold the
lamp cage by the handle and
pull it towards you.
Press the lamp cage firmly into
the lamp cage compartment.
Fasten the securing screws.
Slide the lamp cage cover in the
direction of the arrow. Then
fasten the user service screw.
Securing
Securing
screw
screw
User service screw
E-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Projection Lamp
Resetting the lamp timer
Connect the power
cord.
Reset the lamp timer.
1
2
Plug the power cord into the AC
socket of the projector.
While pressing ƒ, © and
ENTER on the projector, press
POWER ON on the projector.
“LAMP 0000H” is displayed,
indicating that the lamp timer is
reset.
• Reset the lamp timer only after replacing the lamp.
Using the Kensington Lock
This projector has a Kensington Security Standard
connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the
system for instructions on how to use it to secure the
projector.
Kensington Security
Standard connector
Troubleshooting
Problem
Check
No picture and no sound.
• Projector power cord is not plugged into the wall outlet.
• Selected input is wrong. (See page 17.)
• Cables improperly connected to side panel of the projector. (See pages 11–15.)
• Remote control batteries have run down. (See page 8.)
• Remote control’s MOUSE/ADJUSTMENT switch is set to MOUSE.
Sound is heard but no picture
appears.
• Cables improperly connected to side panel of the projector. (See pages 11–15.)
• “Contrast” and “Bright” adjustments are set to minimum position. (See page 27.)
• On-screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned on,
creating a black image. (See page 37.)
Color is faded or poor.
Picture is blurred.
• “Color” and “Tint” adjustments are not correct. (See page 27.)
• Adjust the focus. (See page 17.)
• Projection distance is too long or too short to allow for proper focus. (See page 18.)
Picture appears but no sound is
heard.
• Cables improperly connected to side panel of the projector. (See pages 11–15.)
• Volume is set to minimum. (See page 17.)
An unusual sound is occasionally • If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes.
heard from the cabinet.
This will not affect operation or performance.
Maintenance indicator lights up.
• Refer to “Lamp/Maintenance Indicators” on page 47.
Data cannot be received via
IrCOM.
• Distance and angle between the projector and transmitting device are out of the designated range.
(See page 25.)
• Refer to the operation manual of the transmitting device.
• Refer to the section “Troubleshooting” in the operation manual of the supplied software.
Picture noise appears.
• Adjust the phase setting. (See page 29.)
• Noise may appear when used with certain computers. Set the NOISE FILTER to ON using the RS-
232C command. (See pages 53 and 54.)
480P images do not appear.
• Set the resolution mode to 480P. (See page 32.)
Color is distorted (except for
VIDEO mode).
• Change the input signal type. (See page 40.)
Lens comes off.
• Align the mark on the lens with the corresponding mark on the projector, push the lens firmly in
place, and rotate to the right.
E-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
E-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Transporting the Projector
A soft-side carrying bag is provided to transport the
projector. Before placing the projector into the carrying
bag, set up the inner pad inside the bag as shown.
Using the Carrying Bag
CAUTION
Projector
• Rotate the focus and zoom rigns to store the lens before
placing the projector into the carrying bag.
• The supplied carrying bag is made exclusively for the
projector and its supplied accessories. Do not place other
items into the carrying bag with the projector or use the
bag to transport items other than the projector and its
accessories.
Inner pad
• This bag is provided merely to transport the projector and
its accessories, not to protect these products from damage
as a result of rough handling. Do not expose these products
to shocks or impact when transported in the carrying bag.
• Wait until the projector has sufficiently cooled before placing
it into the carrying bag. If the projector is placed into the
bag while it is still hot, the heat may damage the bag lining.
Carrying bag
Attaching the shoulder strap to the carrying bag
Take the shoulder strap
out.
Fasten the shoulder strap
to the carrying bag.
1
2
The shoulder strap is stored in the
pocket located in front of the
carrying bag.
Follow the same procedure for the
other end of the strap.
Using the Lens Cap Strap
A lens cap strap is provided to prevent the loss of the lens cap.
Attach the lens cap strap to the lens
cap.
Attach the lens cap strap to the
projector.
1
2
• You can also use the end of a mechanical pencil or other pointed object to feed the lens cap strap through the openings.
E-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Pin Assignments
Analog Computer 1 Signal Input Port: 15-pin mini D-sub female connector
Computer Input
Analog
1. Video input (red)
2. Video input
9. Not connected
10. GND
11. GND
(green/sync on green)
1
3. Video input (blue)
4. Reserve input 1
5. Composite sync
6. Earth (red)
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clock
5
10
15
6
11
7. Earth (green/sync on green)
8. Earth (blue)
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No.
Signal
CD
RD
SD
Name
I/O
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
1
2
3
4
5
6
7
8
9
5
1
Receive Data
Send Data
Input
Output
ER
SG
DR
RS
CS
CI
Signal Ground
Data Set Ready
Request to Send
Clear to Send
Output
Output
Input
6
9
RS-232C Terminal: 9-pin mini DIN connector
Pin No. Signal
Name
I/O
Reference
8
1
2
3
4
VCC
RD
ם 3.3V (Reserved) Receive Data
Send Data
Output
Input
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
7
9
SD
Output
EXIR
Detector of Option Unit Input
(Reserved)
Signal Ground
IR Receive Signal from Input
IR Amplifire (Reserved)
6
3
5
6
SG
ERX
Connected to internal circuit
Not connected
7
8
9
RS
CS
ETX
Request to Send
Clear to Send
IR Transmit Signal
(Reserved)
Output
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
5
4
2
1
PanelLink™ Port: MDR-type 20-pin connector
Pin No.
1
Signal
RX0
מ Name
Reference
10
1
Blue Input (
מ ) Blue Input (
ם ) Panel Link Shield
Panel Link Shield
Red Input (
מ ) Red Input (
ם ) SCL
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
2
RX0
ם 3
RX0 SHIELD
RX2 SHIELD
RX2
מ 4
5
6
RX2
ם 7
DDC/SCL
DDC/SDA
NC
20
11
8
SDA
9
N.C.
10
11
12
13
14
15
16
17
18
19
20
NC
N.C.
Not connected
RXC
מ Clock Input (
מ ) Clock Input (
ם ) Panel Link Shield
Panel Link Shield
Green Input (
מ ) Green Input (
ם ) N.C.
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
RXC
ם RXC SHIELD
RX1 SHIELD
RX1
מ RX1
ם NC
SENS
SENS
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
DDC
ם 5V DC DDC GND
ם 5V GND
E-52
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Port Specifications
PC control
A computer can be used to control the projector by connecting an RS-232C cable (cross type, sold separately) to
the projector. (See page 14 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate:
Data length:
Parity bit:
9,600 bps
8 bits
NON
Stop bit:
1 bit
None
Flow control:
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the
projector processes the command from the computer, it sends a response code to the computer.
Command format
Return code (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits
Response code format
Normal response
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
When more than one code is being sent, send each command only after the OK response code for the previous
command from the projector is verified.
• When using the computer control function of the projector, the projector operating status cannot be read to the computer.
Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with
the On-screen Display. If the projector receives a command other than a menu display command, it will execute the com-
mand without displaying the On-screen Display.
Commands
EXAMPLE
• When “BRIGHT” of INPUT 1 IMAGE ADJUSTMENT is set to
מ 10. Computer
Projector
→
←
R
A
B
R
_
מ 1
0
O
K
COMMAND
PARAMETER
COMMAND
PARAMETER
CONTROL
CONTENTS
CONTROL
CONTENTS
CONTROL ITEM
CONTROL ITEM
C1 C2 C3 C4 P1 P2 P3 P4
C1 C2 C3 C4 P1 P2 P3 P4
A
A
P
P
I
P
P
O
O
W
W
E
W
W
R
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
0
1
1
1
2
1
0
AUTO POWER OFF
AUTO POWER ON
M
M
M
M
M
M
M
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
L
L
L
L
L
L
L
L
L
L
L
A
A
A
A
A
A
A
A
A
A
A
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
2
3
4
5
6
7
8
9
0
1
ENGLISH
AUTO POWER OFF
DEUTSCH
ESPAÑOL
NEDERLANDS
FRANÇAIS
ITALIANO
O
O
V
POWER OFF (STANDBY)
POWER ON
VIDEO
POWER SETTING
R
LANGUAGE
SELECTION
D
B
I
R
R
C
C
G
G
O
H
INPUT1
INPUT SWITCHING
INPUT CHECK
I
B
INPUT2
SVENSKA
I
M
K
IrCOM
I
INPUT CHECK
PORTUGUÊS
KEYSTONE
ADJUSTMENT
KEYSTONE
(
מ 127 – ם 127) *
K
E
Y
S
*
*
*
E-53
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Port Specifications
COMMAND
PARAMETER
COMMAND
PARAMETER
CONTROL
CONTENTS
CONTROL
CONTENTS
CONTROL ITEM
CONTROL ITEM
C1 C2 C3 C4 P1 P2 P3 P4
C1 C2 C3 C4 P1 P2 P3 P4
*
M
M
M
M
M
V
V
V
V
V
V
V
V
V
V
I
E
E
S
S
S
S
S
P
B
C
T
Y
Y
Y
Y
Y
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
*
1
2
3
4
5
*
AUTO
I
I
N
N
A
C
P
H
V
R
R
D
D
R
R
I
L
H
P
P
E
E
I
*
*
*
*
*
CLOCK (
מ 150 – ם 150) PHASE (
מ 60 – ם 60) H-POS (
מ 150 – ם 150) V-POS (
מ 60 – ם 60) COMPUTER INPUT DISPLAY
RESET
*
PAL (50/60 Hz)
SECAM
_
*
VIDEO
SYSTEM
SELECTION
*
E
I
*
*
INPUT
ADJUSTMENT
*
E
NTSC 4.43
I
A
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
0
1
0
1
0
1
0
1
0
1
0
1
1
2
1
2
3
4
1
2
3
4
E
NTSC 3.58
I
A
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
A
A
A
A
A
A
A
A
A
A
M
M
M
M
M
M
M
O
U
U
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
A
A
D
CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) COLOR (
מ 30 – ם 30) TINT (
מ 30 – ם 30) SHARPNESS (
מ 30 – ם 30) RESET
I
A
R
O
I
*
*
*
I
M
M
M
M
M
M
M
M
M
M
A
OSD DISPLAY OFF
OSD DISPLAY ON
REVERSE OFF
*
*
*
I
I
*
*
*
I
E
E
N
N
S
S
P
P
I
VIDEO
IMAGE
ADJUSTMENT
S
R
R
B
R
R
B
B
B
B
S
S
S
L
H
E
D
E
E
E
G
G
G
G
I
*
*
*
I
REVERSE ON
_
*
_
*
1
*
I
INVERT OFF
SCREEN SETTING
RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) VIDEO DISPLAY
RESET
I
I
INVERT ON
*
*
*
I
A
A
I
AUTO SYNC DISPLAY OFF
AUTO SYNC DISPLAY ON
I/P CONVERSION INTERLACED
I/P CONVERSION PROGRESSIVE
RGB
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
_
_
*
0
1
1
2
3
4
1
2
3
*
I
I
SHARP
I
I
I
CUSTOM
I
S
S
M
M
M
M
M
M
M
M
INPUT1 SIGNAL TYPE
SELECTION
BACKGROUND
SELECTION
I
BLUE
I
A
I
COMPONENT
I
NONE
G
G
G
G
G
G
G
G
A
R
R
R
R
V
V
V
V
STANDARD
I
SHARP
A
GAMMA1
INPUT GAMMA
SELECTION
STARTUP
IMAGE
SELECTION
I
I
CUSTOM
A
GAMMA2
I
I
NONE
A
CUSTOM
V
M
M
A
A
A
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
A
A
A
A
E
E
E
A
E
E
I
VOLUME (00 – 60)
MUTE OFF
A
STANDARD
VOLUME
ADJUSTMENT
T
_
_
*
0
1
*
A
GAMMA1
VIDEO GAMMA
SELECTION
T
MUTE ON
A
GAMMA2
T
TREBLE (
מ 30 – ם 30) BASS (
מ 30 – ם 30) AUDIO DISPLAY
RESET
A
CUSTOM
B
R
R
P
B
R
B
R
C
T
*
*
*
AUDIO
ADJUSTMENT
VIDEO
CONFIRMATION
0
S
Y
S
E
_
_
_
DISPLAY
_
_
*
_
_
*
0
1
*
0
1
0
1
*
I
M
M
M
M
E
B
B
B
B
M
M
S
S
S
S
S
S
S
S
S
S
S
I
K
K
O
O
S
L
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
BLACK SCREEN OFF
BLACK SCREEN ON
BLACK SCREEN DISPLAY OFF
BLACK SCREEN DISPLAY ON
SAVE SETTING (1–7)
SELECT SETTING (1–7)
NORMAL
CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) INPUT 1 DISPLAY
COLOR (
מ 30 – ם 30) TINT (
מ 30 – ם 30) SHARPNESS (
מ 30 – ם 30) RESET
I
BLACK SCREEN
R
D
E
E
O
I
*
*
*
I
*
*
*
I
*
*
*
M
M
R
R
R
R
R
R
R
R
R
R
R
N
N
SCREEN MODE
MEMORY
INPUT 1
IMAGE
ADJUSTMENT
*
_
*
_
*
0
*
E
1
2
3
4
1
2
3
4
1
2
3
0
1
A
A
A
A
B
B
B
B
A
A
A
F
R
R
R
R
R
R
R
R
V
V
V
L
*
*
*
WIDE/FIT TO SCREEN
DOT BY DOT
INPUT1 RESIZE
INPUT2 RESIZE
S
R
P
B
R
B
R
R
D
D
J
H
E
I
*
*
*
_
*
_
*
1
*
DOT BY DOT (WIDE)
NORMAL
CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) INPUT 2 DISPLAY
RESET
R
D
E
E
E
J
*
*
*
WIDE/FIT TO SCREEN
DOT BY DOT
*
*
*
INPUT 2
IMAGE
ADJUSTMENT
*
*
*
DOT BY DOT (WIDE)
NORMAL
_
_
_
_
_
_
_
_
_
_
0
1
0
1
1
VIDEO RESIZE
NOISE FILTER
WIDE
AUTO SYNC OFF
AUTO SYNC ON
AUTO SYNC START
DOT BY DOT
INPUT AUTO
SYNCHRONIZATION
J
FILTER OFF
S
F
I
L
FILTER ON
• If a dash (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated
in brackets under CONTROL CONTENTS.
• INPUT ADJUSTMENT can only be set in the displayed computer mode.
• Noise may appear when used with certain computers. Set the NOISE FILTER to ON using the RS-232C command.
E-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Signals (Recommended Timing)
The computer output signal timing of different types of computer signals are shown below for reference.
For IBM and compatibles
VIDEO SIGNAL
For Macintosh Series
VIDEO SIGNAL
HORIZONTAL
SYNC SIGNAL
e
C-SYNC(H)
a
b
c
d
VIDEO SIGNAL
e = 2 dot
d
a
b
VERTICAL
SYNC SIGNAL
c
VIDEO SIGNAL
C-SYNC(V)
w
z
x
y
w
z
x
y
V-SYNC
The following is a list of compatible VESA standards. Please note that this projector also accepts signals outside
of the VESA standards.
Computer compatibility table for INPUT 1 (HD-15)
• Depending on the mode selected, the projector may clearly display images under 200 Hz.
HSYNC
VSYNC
FRONT
PORCH
a
BACK
PORCH
c
VIDEO
PERIOD
d
FRONT
PORCH
w
BACK
PORCH
y
VIDEO
PERIOD
z
MODE
VIDEO
1H
1V
1dot
1/H
1/dot
LEVEL
1/V
LEVEL
SYNC
b
SYNC
x
(a
b c d) (w
x y z) dot
640
line
350
LEVEL
TYPE
dot
32
32
36
8
dot
64
dot
96
dot
640
dot
µs
ns
kHz
MHz
H
32
1
1
2
1
1
1
1
1
37
1
1
0
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
H
3
3
3
2
3
3
3
2
4
6
3
3
4
6
6
3
3
3
3
3
3
3
3
3
3
3
3
3
H
H
H
ms
Hz
832
26.4
26.4
26.4
31.8
26.4
26.7
23.1
28.4
26.4
20.8
21.3
18.6
28.2
20.7
17.7
16.7
14.6
14.8
16.7
11.6
15.6
12.5
11.0
13.3
12.3
11.4
10.7
9.4
31.7
31.7
28.2
39.7
31.7
31.7
27.8
27.8
25.0
20.0
20.2
17.8
22.3
15.4
13.3
12.7
10.6
9.3
37.861
37.861
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
35.522
48.363
56.476
60.023
68.677
67.500
60.000
85.938
63.981
79.976
91.146
75.000
81.250
87.500
93.750
106.250
31.500
31.500
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
44.900
65.000
75.000
78.750
94.500
108.000
108.000
148.500
108.000
135.000
157.500
162.000
175.500
189.000
202.500
229.500
60
41
42
25
20
16
25
22
23
23
21
27
20
29
29
28
36
32
36
47
38
38
44
46
46
46
46
46
350
445
11.8
11.8
11.8
16.7
13.7
13.3
11.8
17.8
16.6
13.9
13.3
11.8
23.0
16.7
14.3
13.3
11.8
13.3
16.7
11.8
16.7
13.3
11.8
16.7
15.4
14.3
13.3
11.8
85.080
85.080
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
43.479
60.004
70.069
75.029
84.997
75.000
60.000
85.002
60.020
75.025
85.024
60.000
65.000
70.000
75.000
85.000
VESA
Standard
640
400
64
96
640
832
400
445
720
400
72
108
40
720
936
400
446
Industry
Standard
VGA
640
480
96
640
800
480
525
640
480
16
16
56
24
40
56
16
32
8
40
120
120
80
640
832
480
520
VESA
Standard
640
480
64
640
840
480
500
640
480
56
640
832
480
509
800
600
72
128
88
800
1,024
1,056
1,040
1,056
1,048
1,264
1,344
1,328
1,312
1,376
1,600
1,800
1,728
1,688
1,688
1,728
2,160
2,160
2,160
2,160
2,160
600
625
VESA
Guidelines
800
600
128
120
80
800
600
628
SVGA
800
600
64
800
600
666
VESA
Standard
800
600
160
152
56
800
600
625
800
600
64
800
600
631
Industry
Standard
VESA
1,024
1,024
1,024
1,024
1,024
1,152
1,280
1,280
1,280
1,280
1,280
1,600
1,600
1,600
1,600
1,600
768
176
136
136
96
1,024
1,024
1,024
1,024
1,024
1,152
1,280
1,280
1,280
1,280
1,280
1,600
1,600
1,600
1,600
1,600
768
817
768
24
24
16
48
64
96
64
48
16
64
64
64
64
64
64
160
144
176
208
256
312
224
248
248
224
304
304
304
304
304
768
806
Guidelines
0.7 Vp-p
75 Ω load
R • G • B
TTL
TTL
XGA
768
768
806
768
768
800
768
96
768
808
864
128
112
160
112
144
160
192
192
192
192
192
864
900
960
9.3
960
1,000
1,011
1,066
1,066
1,072
1,250
1,250
1,250
1,250
1,250
960
6.7
960
SXGA
1,024
1,024
1,024
1,200
1,200
1,200
1,200
1,200
9.3
1,024
1,024
1,024
1,200
1,200
1,200
1,200
1,200
VESA
Standard
7.4
6.3
6.2
5.7
UXGA
5.3
4.9
4.4
E-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Signals (Recommended Timing)
HSYNC
VSYNC
FRONT
PORCH
a
BACK
PORCH
c
VIDEO
PERIOD
d
FRONT
PORCH
w
BACK
PORCH
y
VIDEO
PERIOD
z
MODE
VIDEO
1H
1V
1dot
1/H
1/dot
LEVEL
1/V
LEVEL
SYNC
b
SYNC
x
(a
b c d) (w
x y z) dot
line
480
624
768
870
900
900
900
480
480
720
1,080
LEVEL
TYPE
dot
64
31
35
36
29
16
24
–
dot
64
65
96
128
128
96
96
–
dot
96
dot
640
832
1,024
1,152
1,152
1,152
1,024
–
dot
864
1,152
1,328
1,456
1,504
1,472
1,312
–
µs
28.6
20.1
16.7
14.5
14.8
13.9
14.1
–
ns
33.1
17.5
12.5
10.0
10.8
9.5
10.8
–
kHz
MHz
30.2400
57.246
79.760
100.300
92.940
105.561
92.940
–
H
3
1
3
3
2
2
2
–
–
–
–
H
3
3
3
3
4
8
8
–
–
–
–
H
39
39
30
39
31
33
33
–
H
480
624
768
870
900
900
800
–
H
525
667
804
915
937
943
843
–
ms
15.0
13.4
13.4
13.3
14.3
13.1
11.9
–
Hz
13Љ Monitor
16Љ Monitor
19Љ Monitor
21Љ Monitor
66Hz
640
35.000
49.693
60.000
68.887
61.795
71.713
70.838
15.734
31.469
44.955
33.716
66.670
74.502
74.700
75.287
69.950
76.048
84.031
59.940
59.940
59.740
59.940
832
224
173
140
195
208
168
–
Macintosh™
1,024
1,152
1,152
1,152
1,152
640
R • G • B
0.7 Vp-p
75 Ω load
SUN
TTL
TTL
76Hz
84Hz
480I
480P
640
–
–
–
–
–
–
–
–
–
–
–
–
R • G • B/
COMPONENT
DTV
720P
1,280
1,920
–
–
–
–
–
–
–
–
–
–
–
–
1080I
–
–
–
–
–
–
–
–
–
–
–
–
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how
to change display modes can be found in your notebook computer’s operation manual.
• This projector can receive 640
ן 350 VESA format VGA signals, however, “640 ן 400” will appear on the screen. • When receiving 1,600
ן 1,200 VESA format UXGA signals, sampling occurs and the image is displayed with 1,024 lines, causing part of the image to be blocked.
Computer compatibility table for INPUT 2 (DIGITAL INPUT)
• This projector does not accept Panel Link input from INPUT 2 with a pixel clock greater than 108 MHz.
HSYNC
VSYNC
FRONT
PORCH
a
BACK
PORCH
c
VIDEO
PERIOD
d
FRONT
PORCH
w
BACK
PORCH
y
VIDEO
PERIOD
z
MODE
VIDEO
1H
1V
1dot
1/H
1/dot
LEVEL
1/V
LEVEL
SYNC
b
SYNC
x
(a
b c d) (w
x y z) dot
640
line
350
400
400
480
480
480
480
600
600
600
600
600
768
768
768
768
768
864
960
1,024
LEVEL
TYPE
dot
32
32
36
8
dot
64
dot
96
dot
640
dot
µs
ns
kHz
MHz
31.500
31.500
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
44.900
65.000
75.000
78.750
94.500
108.000
108.000
108.000
H
32
1
H
3
3
3
2
3
3
3
2
4
6
3
3
4
6
6
3
3
3
3
3
H
H
350
400
400
480
480
480
480
600
600
600
600
600
768
768
768
768
768
864
960
1,024
H
445
445
446
525
520
500
509
625
628
666
625
631
817
806
806
800
808
900
1,000
1,066
ms
Hz
832
26.4
26.4
26.4
31.8
26.4
26.7
23.1
28.4
26.4
20.8
21.3
18.6
28.2
20.7
17.7
16.7
14.6
14.8
16.7
15.6
31.7
31.7
28.2
39.7
31.7
31.7
27.8
27.8
25.0
20.0
20.2
17.8
22.3
15.4
13.3
12.7
10.6
9.3
37.861
37.861
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
35.522
48.363
56.476
60.023
68.677
67.500
60.000
63.981
60
41
42
25
20
16
25
22
23
23
21
27
20
29
29
28
36
32
36
38
11.8
11.8
11.8
16.7
13.7
13.3
11.8
17.8
16.6
13.9
13.3
11.8
23.0
16.7
14.3
13.3
11.8
13.3
16.7
16.7
85.080
85.080
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
43.479
60.004
70.069
75.029
84.997
75.000
60.000
60.020
VESA
Standard
640
64
96
640
832
720
72
108
40
720
936
1
Industry
Standard
VGA
640
96
640
800
2
640
16
16
56
24
40
56
16
32
8
40
120
120
80
640
832
1
VESA
Standard
640
64
640
840
1
640
56
640
832
1
800
72
128
88
800
1,024
1,056
1,040
1,056
1,048
1,264
1,344
1,328
1,312
1,376
1,600
1,800
1,688
1
VESA
Guidelines
800
128
120
80
800
1
SVGA
800
64
800
37
1
0.7 Vp-p
75 Ω load
R • G • B
TTL
TTL
VESA
800
160
152
56
800
Standard
800
64
800
1
Industry
Standard
1,024
1,024
1,024
1,024
1,024
1,152
1,280
1,280
176
136
136
96
1,024
1,024
1,024
1,024
1,024
1,152
1,280
1,280
0
VESA
24
24
16
48
64
96
48
160
144
176
208
256
312
248
3
Guidelines
XGA
3
1
96
1
VESA
Standard
128
112
112
1
SXGA
9.3
1
9.3
1
E-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product type Digital Multimedia Projector
Model XG-NV7XU
Video system PAL/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I
Display method Single panel Digital Micromirror Device™ (DMD™) by Texas Instruments
DMD panel Panel size: 55⁄64Љ (21.8 mm), 1 chip XGA DMD
No. of dots: 786,432 dots (1,024 [H]
ן 768 [V]) Lens 1–1.2
ן zoom lens, F2.7–3.0, f ס 35–42 mm Projection lamp P-VIP lamp, AC 120 W
Contrast ratio 500:1
Video input signal RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)
S-video input signal 4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Digital input signal 20-PIN DIGITAL CONNECTOR (INPUT 2):
TMDS/PanelLink
Horizontal resolution 520 TV lines (video input), 750 TV lines (DTV 720P input, Dot by Dot)
Audio output 2 W (monaural)
Computer RGB input signal 15-PIN MINI D-SUB CONNECTOR (INPUT 1):
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,
75 Ω terminated
STEREO MINIJACK: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)
VERTICAL SYNC. SIGNAL: Same as above
Pixel clock 12–230 MHz
Vertical frequency 43–200 Hz
Horizontal frequency 15–126 kHz
Computer control signal 9-pin mini-DIN male connector (RS-232C Input Port)
Speaker system 1 37⁄64Љ
ן 1 3⁄16Љ (4 ן 3 cm) oval Rated voltage AC 110–120/220–240 V
Input current 1.0 A/1.9 A
Rated frequency 50/60 Hz
Power consumption 197 W
Operating temperature 41°F to 95°F (
ם 5°C to ם 35°C) Storage temperature 14°F to 140°F (
מ 10°C to ם 60°C) Cabinet Magnesium alloy (Front panel and rear terminal panel constructed of plastic)
I/R carrier frequency 38 kHz
Laser pointer of remote control Wave length: 650 nm / Max. output: 1 mW / Class II Laser Product
Dimensions (approx.) 9 1⁄4Љ (W)
ן 2 9⁄32Љ (H) ן 12 19⁄64Љ (D) (235 ן 58 ן 312.5 mm) (main body only) 9 1⁄4Љ (W)
ן 3 15⁄64Љ (H) ן 12 43⁄64Љ (D) (235 ן 82 ן 321.8 mm) (including adjustment feet and projecting parts)
Weight (approx.) 6.28 lbs. (2.85 kg)
Supplied accessories Remote control, Two AA size batteries, Power cord (11Ј 10Љ, 3.6 m), Computer cable (9Ј
10Љ, 3 m), Computer audio cable (9Ј 10Љ, 3 m), Mouse control serial cable (3Ј 3Љ, 1 m),
Mouse control cable for IBM PS/2 (3Ј 3Љ, 1 m), Mouse control cable for Mac (6 45⁄64Љ,
17 cm), DIN-D-sub RS-232C cable (6 45⁄64Љ, 15 cm), Remote mouse receiver, Carrying bag,
Lens cap (attached), Lens cap strap, CD-ROM, Projector operation manual, Projector
quick reference, Sharp Advanced Presentation Software operation manual, Sharp
Advanced Presentation Software quick reference, IrDA driver installation instruction sheet
Replacement parts Remote control (RRMCG1530CESA), AA size batteries, Power cord (QACCU5013CEZZ),
Computer cable (QCNW-5304CEZZ), Computer audio cable (QCNW-4870CEZZ), Mouse
control serial cable (QCNW-5112CEZZ), Mouse control cable for IBM PS/2 (QCNW-
5113CEZZ), Mouse control cable for Mac (QCNW-5114CEZZ), DIN-D-sub RS-232C cable
(QCNW-5288CEZZ), Remote mouse receiver (RUNTK0661CEZZ), Carrying bag
(GCASN0003CESA), Lens cap (GCOVH1308CESA), Lens cap strap (UBNDT0012CEZZ),
CD-ROM (UDSKA0009CE01), Projector operation manual (TINS-6786CEZZ), Projector
quick reference (TINS-6787CEZZ), Sharp Advanced Presentation Software operation
manual (TINS-6888CEZZ), Sharp Advanced Presentation Software quick reference (TINS-
6788CEZZ), IrDA driver installation instruction sheet (TCAUZ3046CEZZ)
This SHARP projector uses a DMD panel. This very sophisticated
panel contains 786,432 pixels. As with any high technology electronic
equipment such as large screen TVs, video systems and video
cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which
may result in inactive dots on the picture screen. This will not affect
the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-800-
BE-SHARP (1-800-237-4277). U.S.A. ONLY
Specifications are subject to change without notice.
E-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Rear View
Top View
Side View
9 1/4 (235)
Front View
8 11/32 (212)
Bottom View
Units: inches (mm)
E-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
Electronic presentations are one of the most effective
tools presenters can use to persuade an audience.
There are several ways to enhance your presentation
and maximize your effectiveness. The following are
guidelines to help you create and deliver a dynamic
presentation.
a.Types of Presentations
Computer Presentations
• To present basic information such as graphs, spreadsheets,
documents and images, use word processing and spreadsheet
applications.
30
25
20
15
10
5
• To convey more complex information and create more dynamic
presentations which allow you to control the pace of your delivery,
utilize software such as Astound®, Freelance®, Persuasion® or
PowerPoint®.
• For high-end multimedia and interactive presentations, use software
0
such as Macromedia Director®.
• Astound®, Freelance®, Persuasion®, PowerPoint® and Macromedia
Director® are trademarks of their respective companies.
Video Presentations
Use of video equipment, such as a VCR, DVD player and laser disc
player, can be effective for delivering instructional or illustrative
information that is difficult to present.
Digital Cameras and Personal Digital Assistants
(PDAs)
For highly compact and portable presentations, still cameras, digital
video cameras, document cameras and PDAs are ideal for transferring
data without cumbersome conversions.
Multimedia Presentations
You can integrate all of the above methods for a full multimedia
presentation including video, audio, computer applications and World
Wide Web information.
Wireless Presentations
Use any IrDA/IrTranP compatible source such as a laptop, digital
camera or PDA to project still images quickly and effortlessly without
the use of cables.
b. Creative Presentations
Oftentimes presenters do not take advantage of the many
subtle ways they can manipulate their electronic slides to more
effectively persuade the audience.
Color has a great effect on the audience during a presentation.
When used correctly and legibly, studies show that
background & foreground colors establish an emotional tone
for a presentation, help viewers understand and retain
information, and influence an audience to take a desired
course of action.
Color Considerations
• Choose legible colors.
• Text and graphics colors need sufficient contrast.
• Use darker colors for the background since a lighter background
can create uncomfortable glare. (Yellow on black creates an ideal
contrast.)
Yellow
on Black
E-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
• Background colors can subconsciously affect the audience:
Red—increases viewers’ pulse and breathing and
encourages risk taking but can also be associated with
financial loss.
Red
Blue
Blue—has a calming and conservative affect on the
audience but can also create boredom among corporate
audiences that are often inundated with this background
color.
Green—stimulates interaction.
Green
Black
Black—conveys finality and certainty. Use it as a transitional
color between slides when moving from one idea to another.
• Foreground colors create a major impact on how well an
audience understands and remembers a message.
• Use one or two bright colors for emphasis.
• Highlight important messages.
• The eye has a difficult time reading certain colored text on
certain colored backgrounds. For example, text and
background colors in red and green, and blue and black
make for difficult viewing.
• Colorblind individuals may find it difficult to distinguish
between red and green, brown and green, and purple and
blue. Avoid using these colors together.
Fonts
Presentation from SHARP
f
s
o
pe
ty
nt
fo
y
an
f
s
in
o
ke
ista
n
lectio
se
to
ard
m
on
m
pe
d.
om
c
ty
t
os
e
nta
m
tio
f
th
e
re
o
e
On
p
th
th
al is
o
rea
isu
m
n
s
v
r
o
h
se
re
,
in
• One of the most common mistakes in any type of
presentation visual is the selection of type fonts that are too
small, too thin, or too difficult to read.
all, to
o
to
at
a
th
• If you are not sure how well a given font will read on a screen
at various sizes, try this: Draw a 6Љ
ן 8Љ box on a piece of paper and print out several lines of text inside the box with
your computer printer at 300 or 600 dpi resolution. Vary the
sizes of text to simulate headline, body and text call-outs
for any charts or graphs. Hold the printout at arm’s length.
This is how your text will look on a 4Ј (1.2 meters)-wide
screen at 10Ј (3 meters), on a 7.5Ј (2.3 meters)-wide screen
at 20Ј (6.1 meters) and a 12Ј (3.7 meters)-wide screen at
30Ј (9.1 meters). If you cannot read the text easily, you
should put less copy on your visuals or use larger typefaces.
• Design your visuals so that they are visible by the viewer in
the last row.
• Nothing will ruin your presentation faster than misspelled
words. Take the time to proofread and edit your work before
your visuals become a permanent part of your presentation.
• Mixed case text is easier to read than text which is displayed
in capital letters.
• Another important attribute of fonts is whether any particular
face is serif or sans-serif. Serifs are small, usually horizontal
cross strokes that are added to the end of a letter’s main
strokes. Because of their ability to coax the eye along the
line of type, fonts with serifs are generally acknowledged to
be more readable.
Sans-serif
Serif
E-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
c. Set-Up
Good
Bad
Good
When giving a presentation, you need to set the stage both
figuratively and literally for success. The way you set up a
presentation room will have a great impact on the audience’s
perception of you and your message. By manipulating the
placement and use of the following tools, you will improve the
impact of your presentation.
Presentation from SHARP
Lighting—Good lighting is an important component of a
successful presentation. You should strive to create an unequal
distribution of light. An audience should always see as much
of the presenter’s face as possible, so most of the light should
be focused on you. Because it is important for you to be able
to read the audience’s faces and body language, some light
should be shed upon them. However, no light should shine
on the screen.
30
25
20
15
10
5
0
Stage— When presenting on the same level surface that your
audience is on, most people can only see the top one-third of
your body. Therefore, it is recommended that when giving a
presentation to an audience of 25 or more, you stand on a
stage or platform. As more of your body is visible, the easier
it is to communicate with an audience.
Podiums—The best presenters avoid podiums because they
hide 75% of the body and restrict movement. However, many
people feel more comfortable with a podium to hold their notes
and hide their discomfort. If you must use a podium, angle it
at 45 degrees to the audience so that you are not completely
hidden.
Visuals—It is imperative that you make sure your visuals are
large enough and projected far enough for the audience to
see. Eight times the height of an image is the optimal viewing
distance to read 24 point type. The bottom of a screen should
be at least 6Ј (1.8 meters) above the floor.
Screen—The screen should always be in the center of the
room so that all audience members can see it. Because people
read from left to right, you should always stand to the
audience’s left when discussing visuals.
Seating—Arrange seating according to the dynamics of your
presentation. If the presentation is more than half-a-day, use
classroom style seating—a chair and a desk. If you would
like to encourage audience interaction, use chevron seating,
angling the chairs into a “V” shape. When you have a very
small audience, a “U” shaped arrangement will increase
interchange.
E-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
d. Rehearsing & Delivery
• The best time to rehearse is the day or evening before,
not a couple of hours before, and the best place to
rehearse is in the actual room. Rehearsing a speech
in a small office is not the same as standing up in
front of 100 people in a hotel ballroom or classroom.
• Due to varying processor speeds of computers,
practice your slide transitions for proper timing.
• Whenever possible, set up your equipment well in
advance to allow adequate time to resolve any
unexpected issues such as lighting, power, seating
and audio.
• Thoroughly check every piece of equipment you bring
along. Make sure you have fresh batteries in your
remote controls and laptop computer. Fully charge
your computer’s battery before the presentation and
connect your AC adaptor for added safety.
• Make sure you are completely familiar with the control
panel on your projector and remote controls.
• If you are using a microphone, check it out before
hand and walk around to see where you might have
problems with feedback. Avoid standing in these
problem areas during your presentation.
e. Presentation Tips
• Before beginning, visualize yourself delivering an
outstanding presentation.
• Know your speech, memorizing at least the first three
minutes of your presentation will allow you to focus
on your rhythm and pacing.
• Speak to early arrivals to help you build a rapport
with the audience and make you feel more
comfortable.
• Do not be overly dependent on your visuals by reciting
what your audience is already reading. Know your
material well enough to be able to deliver the
presentation with ease. Use your visuals to emphasize
keypoints.
• Be sure to project your voice clearly and use eye
contact to maintain audience attention.
• Do not wait until halfway through your presentation to
get your point across. If you wait and try to create a
“build-up”, you may lose some of your audience along
the way.
• Keep your audience’s attention. As most people only
focus for 15 to 20 minutes during a one-hour
presentation, it is important to recapture their attention
periodically. Use phrases like, “This is critical to my
point” or “This is absolutely fundamental” to remind
them you are saying something they need to hear.
E-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Aspect ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide
images with an aspect ratio of 16 : 9 and 21 : 9.
Auto sync
Optimizes projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being input.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
Compatibility
Ability to use with various image signal modes.
Composite sync
Signal combining horizontal and vertical sync pulses.
Digital keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle.
Direct digital computer input
Digital input terminal developed by Silicon Image that can receive a digital signal from the PC platform.
DMD
Digital Micromirror Device™ (DMD™) by Texas Instruments.
Dot by dot
Mode that projects images in their native resolution.
Fit to screen
Function to adjust an image without keeping a native aspect ratio other than 4 : 3, and project it in a 4 : 3 ratio.
GUI
Graphical User Interface. User interface with graphics that allow easier operation.
I/P conversion
Function to convert an image between “Interlaced” and “Progressive” scan displays.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
IrCOM
Function to transmit still images from a computer, hand-held PC or digital still camera via infrared communication for
“Wireless Presentations”.
IrDA
Standard protocol for wireless communication.
IrTranP
Standard format (protocol) for transmission of images.
PDF
Portable Document Format. Documentation format used to transfer text and images from the CD-ROM.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the
projected image typically displays horizontal flicker.
Presentation tools
Helpful tools used to emphasize keypoints throughout a presentation.
RS-232C
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Startup image
The image displayed when the projector is turned on.
Status function
Displays the settings of each adjustment item.
Sync
Synchronizes the resolution and phase shift of two signals. When receiving an image with a resolution different from that of
the computer, the projected image may be distorted.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin.
E-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
L
AC socket......................................................................... 11
ADJUSTMENT buttons..................................................... 23
Aspect ratio...................................................................... 36
Audio adjustments ........................................................... 28
AUDIO INPUT terminal .................................................... 11
AUDIO INPUT terminals................................................... 13
Automatic power shutoff function .................................... 38
Auto sync adjustment ...................................................... 30
AUTO SYNC button.......................................................... 29
LAMP REPLACEMENT indicator...................................... 47
LASER POINTER button................................................... 22
LEFT-CLICK button .......................................................... 22
Lens cap .......................................................................... 51
Lens cap strap ................................................................. 51
M
MENU button.................................................................... 23
MOUSE/ADJUSTMENT switch......................................... 21
MOUSE buttons ............................................................... 22
Mouse control cable for IBM PS/2 ................................... 15
Mouse control cable for Mac ........................................... 15
Mouse control serial cable ............................................... 15
MUTE button .................................................................... 17
B
Background ..................................................................... 41
BACKLIGHT button.......................................................... 22
BLACK SCREEN button ................................................... 37
C
O
Carrying bag .................................................................... 51
Ceiling-mount................................................................... 20
Ceiling
ם Rear ................................................................... 43 Clock ................................................................................ 29
Computer audio cable ..................................................... 11
Computer cable ............................................................... 11
On-screen display language ........................................... 26
P
PDF ..................................................................................
6
Phase ............................................................................... 29
Picture adjustments ......................................................... 27
POWER buttons ............................................................... 16
Power cord ....................................................................... 11
POWER indicator ............................................................. 16
Presentation tools............................................................. 44
Cooling fan (Exhaust vent)...............................................
5
D
Digital keystone correction .............................................. 19
DIN-D-sub RS-232C cable............................................... 14
Dot by dot ........................................................................ 36
R
Rear projection................................................................. 20
Remote control ................................................................. 21
Remote control sensor ..................................................... 21
Remote mouse receiver ................................................... 21
RESIZE button.................................................................. 36
RIGHT-CLICK button ........................................................ 22
RS-232C port ................................................................... 14
E
ENLARGE button ............................................................. 34
ENTER button................................................................... 23
F
Fit to screen ..................................................................... 36
Foot releases.................................................................... 19
FREEZE button................................................................. 33
S
Sharp Advanced Presentation Software (SAPS).............. 25
Special mode adjustment ................................................ 32
Startup image .................................................................. 42
Status function ................................................................. 45
S-VIDEO INPUT terminal.................................................. 13
Sync ................................................................................. 30
Sync on green .................................................................. 52
G
GAMMA button ................................................................ 35
GUI (Graphical User Interface)........................................ 23
I
INPUT 1 port .................................................................... 11
INPUT 2 port .................................................................... 12
INPUT button.................................................................... 17
T
Intelligent compression and expansion ...........................
3
TEMPERATURE WARNING indicator ............................... 47
TOOLS button .................................................................. 44
I/P conversion .................................................................. 39
IrCOM............................................................................... 25
IrCOM button ................................................................... 25
IrCOM sensor................................................................... 25
IrDA .................................................................................. 59
IrTranP .............................................................................. 59
U
UNDO button ................................................................... 19
V
VIDEO INPUT terminal ..................................................... 13
VOLUME buttons ............................................................. 17
K
Kensington Security Standard connector ........................ 49
KEYSTONE button ........................................................... 19
W
Wireless mouse ................................................................ 21
E-64
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
OSAKA, JAPAN
Printed in Japan
-
TINS 6786CEZZ
T2278-A
-
9P08 JWG
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Car Video System PN ZS1C User Manual
Sherwood Stereo System RD 7503 User Manual
Sony Bluetooth Headset DR BT22 User Manual
Sony Car Stereo System CDX M800 User Manual
Sony Clock Radio ICF C215 User Manual
Sony Speaker System SRS RF80RK User Manual
State Industries Electric Heater Self Cleaning Commercial Gas Water Heaters User Manual
Subaru Automobile Impreza 25GT User Manual
SUPER MICRO Computer Computer Hardware X7DBT User Manual
Sylvania TV DVD Combo 6513DD 6519DD User Manual