R
28LF-92H
32LF-92H
COLOUR TELEVISION
OPERATION MANUAL
Please read this operation manual carefully
before using the colour television.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear SHARP Customer
Congratulations! You are now the proud owner of a SHARP Colour Television Receiver. To ensure proper operation, please
read this manual carefully. After reading, keep this manual in a safe place for future reference.
TERMS OF GUARANTEE
Subject to the conditions listed below Sharp Electronics (U.K.) Ltd. (Hereinafter called «the Company») guarantee
to provide for the repair of, or at its option replace the Sharp Equipment, or any component thereof, (other than
Batteries), which is faulty or below standard, as a result of inferior workmanship or materials.
The conditions of the guarantee are:
1. This guarantee shall only apply to defects or faults which are notified to the Company, or its approved Service
Facility within one year from the date of purchase of the equipment.
2. This guarantee covers equipment intended for private domestic use only. This guarantee does not apply to
equipment used in the course of a business, trade or profession.
3. This guarantee does not cover any faults or defects caused by accident, misuse, fair wear and tear, neglect,
tampering with the equipment, or any attempt at adjustment or repair other than by an approved Service Facility.
4. In the unlikely event of that your equipment should require repair, please contact the dealer or supplier from whom
it was purchased.
5. The cost of carriage to and from the Dealer, Supplier or Sharp approved Service Facility shall be borne by the
purchaser.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to the consumers statutory rights and does not affect rights
in any way.
In the unlikely event of this equipment requiring repair during the guarantee period, you will need to provide proof of date
of purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at the time of purchase.
- 2 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Television equipment and cart combination should be moved
with care. Quick stops, excessive force, and uneven surfaces
may cause the equipment and cart combination to overturn.
This equipment complies with the requirements of Directives
89/336/EEC, 92/31/EEC and 73/23/EEC as amended by 93/
68/EEC.
This receiver should only be operated from a 220-240V AC,
50 Hz outlet. Ensure you select the correct voltage setting
for your convenience.
To prevent fire or electrical shock, do not use the TV set in
an excessively damp place.
To prevent electrical shock, do not subject the AC power cord
to damage by bending or twisting it, or by placing heavy
items on top of it and do not place the AC power cord under
the TV set. If the AC power cord becomes damaged, unplug
it from the wall outlet immediately and call your dealer for
service.
Position the TV set out of direct sunlight and away from heat,
as high temperatures can damage the cabinet, CRT, or other
electronic parts.
Do not place this television equipment on an unstable cart,
stand, or table. The television equipment may fall, causing
serious injury to a child or an adult, and serious damage to
the equipment.
Use only with a cart or stand recommended by the manufac-
turer, or sold with the television equipment.
Do not cover ventilation slots with objects such as newspa-
pers, tablecloths, curtains, etc.
Do not cover the ventilation holes at the back of the TV set,
this can cause fire or other serious problems. Leave an ade-
quate open space behind the TV set for good ventilation.
Never remove the back of the cabinet, as there is high volt-
age in the TV set.
Please call for service.
When replacement parts are required, be sure the service
technician has used replacement parts which are specified
by the manufacturer or have the same specifications as the
original one. Unauthorized substitutions may result in fire,
electrical shock, or other hazards.
In order to ensure that the television is properly ventilated,
leave a space of at least 10 cm around the set.
Do not install this equipment in a confined space such as a
bookcase or a built-in cabinet.
- 3 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV3HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Unplug the power cord from the wall outlet immediately if the Do place the TV set onto an even stand, table or track which
TV set begins to make unusual noises or give off smoke or size is bigger than the TV set.
an odd smell, then call your dealer for service.
If the TV set is put onto a smaller size or uneven stand, table
or track may cause the TV cabinet distort. Do not put or in-
sert anything between TV set and the stand, table or track.
Always disconnect your television from the mains and the
aerial cables during thunderstorms.
Even if your television is switched off, it can still be damaged
by lightning striking the mains and/or aerial cable.
Do not leave your TV set in Stand-by or operating mode when
you leave the house.
The tube of your TV has a special coating. Do not knock or
rub on the tube face with sharp or hard surfaces, otherwise
you will damage the coating.
To prevent damaging the surface of the television screen, re-
move finger prints only with a soft cloth dampened with glass
cleaner. Do not use any abrasive cleaners.
Do not use thinner, benzene or other strong chemical clean-
ers.
In order to prevent electrical shocks and fires, ensure that
the television is not subjected to splashes or spills of water,
and avoid inserting objects or pouring any type of liquid into
the set.
To prevent fire, never place any type of candle or naked
flames on the top or near the TV set.
Warning!
If an object or liquid enters the set, disconnect the mains
supply and contact technical service.
Any intervention contrary to regulations, in particular,
any modification of high voltage or a replacement of the
picture tube may lead to an increased concentration of
x-rays. Any television modified in this way no longer
complies with license and must not be operated.
Instructions for waste disposal:
Packaging and packaging aids are recyclable and
should principally be recycled. Packaging materials,
such as foil bag, must be kept away from children.
Batteries, including those which are heavy
metal-free, should not be disposed of with household
Wall or shelf mounting should follow the manufacturers in-
structions, and should use a mounting kit approved by the
manufacturer.
waste. Please dispose of used batteries in an environ
mentally sound manner. Find out about the legal regulat-
ions which apply in your area.
CAUTION: For environmental and safety reasons, it is recommended that this television set is not left in stand-by
mode whilst not in use. Switch it off using the main switch. During periods of absence from home it is also
wise to disconnect the set by unplugging the mains plug.
- 4 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV4HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
ꢀ
ꢀ
- 5 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV5HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Buttons
= Stand By
= Cursor Up
= Cursor Right
OK = OK
= Info (Program Menu)
0 - 9 = Direct Program
-/-- = Double Digit
= Wide mode button
P/CH+ = Program +
+ = Volume +
= TV / Quit Menu
= EXT button
(EXT-1, RGB, EXT-2, F-AV, SVHS)
Yellow = Feature Menu
Blue = Installation Menu
= Hold
= Update
= Index Page
= Reveal
= Expand
= Mix
= Teletext
= Time
Red = Sound Menu
Green = Picture Menu
= Mute
I-II = Mono/Stereo - Dual I-II
-
= - Volume
- P/CH = -Program
= Flash back button
M = Menu
= Cursor Down
= Cursor Left
CAUTION
RISK OF ELECTRIC SHOCK
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk
of electric shock of persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
- 6 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV6HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Buttons
FRONT PANEL
VIDEO
Speakers (left + right)
= Power On / Off
= Volume -/+
AUDIO L (L/S/G/I) = Audio left
AUDIO R (R/D/D/D) = Audio right
= Headphone 3,6 mm Ø
CH = Program -/+
S-VIDEO
Antenna Connections
- 7 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV7HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
1. With your thumb nail, pull up the slit as indicated by the
Preparation
arrow to remove the battery cover.
Place TV on a solid surface.
For ventilation, leave a space of at least 10 cm free all around
the set. To prevent any fault and unsafe situations, please do
not place any objects on top of the set.
Use this apparatus in tropical and moderate climates.
Features
Remote Control Colour Television
100 UHF / VHF / Cable channel presets
Cable Channel Compatible
Menu Driven functions
2. Insert two batteries 1.5 V (R03 AAA size). Be sure to
match the battery +/- terminals with the +/- marks inside
the compartment.
2 Euro connector Sockets
Front AV sockets
Front SVHS connector.
NICAM Stereo
Full function teletext (Fastext)
Headphone socket
Direct Channel access
3. Replace the battery cover.
APS (Automatic Programming system) Tuning
Program custom name feature
Automatic search tuning
Sleep Timer
Child lock
Blue mute on no video signals
Audio mute on no video signals
Auto switch of after 5 mins of no signal
WSS (wide screen signal decoding)
NTSC playback
Notes:
Remove batteries if weak or if the unit is not in use for long
periods.
Do not mix old and new batteries.
Before Switching on your TV
Incorrect installation of the batteries may damage the re-
mote control.
Power connection
Switching the TV ON/OFF
Important: The TV set is designed to operate on 220 -240V
AC, 50 Hz.
You can operate your TV either using the remote control
After unpacking, allow the TV set to reach the ambient handset or directly using the TV onset buttons.
room temperature before you connect the set to the mains.
To switch the TV on
Aerial Connections
Your TV will switch on in two steps:
Connect the aerial plug to the aerial input socket located at
the back of the TV.
1- Press the power button located on the front of the TV.
Then the TV switches itself to standby mode and the RED
LED located below the TV turns on.
How to connect external equipment
2- To switch on the TV from stand-by mode either:
See Connecting external equipment on page 18.
Press a digit button on the remote control so that a program-
See the instruction manuals provided with the external de-
me number is selected,
vices too.
or,
Remote Control Battery Installation
Press Power Button and P/CH+ or -P/CH buttons on the
TV or on the remote control respectively, so the TV will
switch on and the RED Led will turn GREEN.
Before using the TV set for the first time, install the supplied
dry batteries in the remote control.
To switch the TV off
Press the stand-by button on the remote control, so the TV
will switch to stand-by mode and the GREEN LED will be-
come RED, or,
Press the power button located on the front of the TV.
- 8 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV8HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the onset buttons
Initial Settings
Volume setting and programme selection can be made using
the buttons on the right side of the TV.
The message PLEASE CHECK ANTENNA CABLE AUTO.
PROGRAMMING SYSTEM will be displayed when you turn
on your TV for the first time.
Volume Setting:
Press
button to decrease volume or
button
to increase volume, so a volume level scale will be dis-
played on the screen.
Programme Selecting:
Press CH button to select next programme or CH
button to select the previous programme.
Note: If you connect Video Recorder to your TV via antenna
input (ANT socket); to tune the VCR channel
Operating with Remote Control
automatically you must set the VCR in play mode before you The remote control handset of your TV is designed to control
start APS.
all the functions of the model you selected. The functions will
be described in accordance with the menu system of your TV.
1- Select LANGUAGE with or button, then press
Functions which you can use out of menu system are de-
scribed below.
the or button to select a menu language.
2- Select COUNTRY with or button, then press the
Volume Setting:
or button to select the correct country.
?
D
A
: OTHER
N
: NORWAY
Press
+ button to increase volume.
: GERMANY
: AUSTRIA
SF
UK
NL
P
: FINLAND
Press -
button to decrease volume.
: UNITED KINDOM
: NETHERLANDS
: PORTUGAL
: SPAIN
Programme Selecting (Previous or next programme):
CH : SWITZERLAND
Press -P/CH button to select the previous programme.
I
: ITALY
Press P/CH+ button to select the next programme.
F
B
: FRANCE
: BELGIUM
E
TR
EIR
: TURKEY
DK : DENMARK
: SWEDEN
: IRELAND
S
3- Press the or buttons to select Tuning Mode. This
allows you to choose how you run the APS. If you select
Channel Tuning Mode, the APS will run through the chan-
nel numbers for your area to locate TV stations. Alterna-
tively if you select Frequency Tuning Mode APS will run
through all the frequencies to locate TV stations.
Programme Selecting (direct access):
4- Select START with or button, then press the
Press digit buttons on the remote control handset to select
programmes between 0 and 9. TV will switch to the selected
program after a short delay.
button to start A.P.S.
A.P.S., (Automatic Programming System) automatically pro-
grammes the received channels in your TVs programme
numbers. During A.P.S., A.P.S. IS RUNNING PLEASE
WAIT will be displayed. After A.P.S. is finalized, the PRO-
GRAM. menu appears.
For a two digit program number press -/-- button. Press
the first digit and then second digit of the programme chan-
nel you want to watch.
To cancel A.P.S., press the
button.
Menu System
Your TV has been designed with a menu system. Display
MENU (main menu) and enter one of five menus (SOUND,
PICTURE, FEATURE, INSTALL. and PROGRAM.).
1- Press M button to display MENU (main menu). The
menu titles will be displayed in the main menu.
2- Press or button to select a menu title, then press
or button to enter the menu.
To exit a menu, press
button.
To go to the previous menu, press M button.
You can delete a channel, insert a channel into a programme
number, or re-start A.P.S. with the PROGRAM. menu. For de-
tails, see PROGRAM. (Programming) menu on page 15.
- 9 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV9HS-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
To Change Headphone Sound Settings:
Sound Menu
When you connect headphones you can change the sound
settings by entering the headphone menu. To do this, select
headphone using or button then enter headphone
menu pressing or button.
To change sound settings:
Press M button, now you are in main menu. In the main
menu, SOUND will be the first selected option. Enter the
sound menu pressing or button.
Setting Volume:
As you enter the sound menu, Volume will be the first select-
ed option.
Press button to increase volume.
Press button to decrease volume.
Setting Headphone Volume:
As you enter the Headphone sound menu, Volume will be
the first selected option.
Press button to increase the headphone volume.
Press button to decrease the headphone volume.
Setting Balance:
Using or button select Balance.
Press button to change balance rightward.
Press button to change balance leftward.
Setting Headphone Sound Mode:
Using or button select Mode.
Pressing or button will change the current sound
mode. (e.g.: If the current sound mode is stereo, it will be
mono or vice versa).
In case of bilingual broadcast, you can select original or
dubbed language again using mode menu. So when some-
body listens to the original language from the loudspeakers,
somebody else can listen to the dubbed language from head-
phone.
Selecting Sound Mode
Using or button select Mode.
Press or button to change Mode.
To Store the Headphone Settings
You can choose MONO, STEREO or DUAL (I-II) mode, only
if the selected channel supports that mode.
You can also change sound mode directly pressing I-II but-
ton on your remote control.
Using or button select Store. Press or but-
ton to store current headphone volume and sound mode.
The stored values will be valid for all the programmes.
Equalizer
To enter Equalizer sub-menu, select Equalizer using or
button, then enter Equalizer menu pressing or
button.
In case of bilingual broadcast (Dual Sound), you can select
original or dubbed language using mode option.
Wide Surround:
The wide surround effect depends on whether the feed is
MONO or STEREO.
If the source feed is MONO, it produces a Pseudo Stereo
effect .
If the source feed is STEREO, it produces a Wide Sur-
round effect, expanding the stereophonic image.
In Mode item there are four predefined and one user defined
options. These are Personal, Music, Speech, Jazz and
Flat. The predefined options can not be changed by the user.
The Personal option may be adjusted by the user.
- 10 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H0S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
The 5 items below the Mode are available to adjust the
sound settings in 5 frequency values: 120 Hz, 500 Hz, 1.5
kHz, 5 kHz and 10 kHz. To change the values of 5 frequency
options, select one of the options by or button, and
then press to increase the value, or to decrease the
value.
Press button to decrease Brightness.
To store the Equalizer settings, press or button on
Store option.
Setting Contrast:
Setting AVL
You can change the Contrast setting only when manual pic-
ture mode is selected.
Automatic Volume Limiting (AVL) function normalizes sound
to obtain fixed output level between programs, having different
sound levels. Pressing or button will turn ON and
OFF this feature.
Using or button select Contrast.
Press button to increase Contrast level.
Press button to decrease Contrast level.
To Store the Settings
Press or button on STORE option to store Sound
menu settings or press OK button.
Setting Colour:
You can change the Colour setting only when manual picture
mode is selected.
Using or button select Colour.
Press button to increase Colour level.
Press button to decrease Colour level.
Auto Store:
Last volume level is stored automatically.
Picture Menu
To change picture settings:
Setting Sharpness:
Press M button, now you are in main menu. In the main
menu, select PICTURE using or button, then enter
the picture menu pressing or button.
Using or button select Sharpness.
Press button to increase Sharpness level.
Press button to decrease Sharpness level.
Note: When Picture Mode is not MANUAL, BRIGHTNESS,
CONTRAST and COLOUR options can not be reached by
Setting Tilt
or buttons.
Using or button select Tilt.
Press button to increase Tilt level.
Press button to decrease Tilt level.
Factory Settings:
In the picture menu press the flashback ( ) button to revert
to the original factory settings.
Setting Brightness:
You can change the Brightness setting only when manual
picture mode is selected.
Using or button select Brightness.
Press button to increase Brightness.
- 11 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H1S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
When you select ZOOM 14:9 or CINEMA, you can change
the vertical scroll by pressing / .
Setting Hue (In AV mode only) :
Using or button select Hue.
Press button to increase Hue level.
* Auto mode (VPS code): The VPS signal is sent by some
broadcasting stations with information of the original size.
Press button to decrease Hue level.
Hue adjust is functional only when NTSC 3.58/4.43 is applied in
AV mode. It does not appear when other colour systems used.
When the TV is in AUTO mode and receives the VPS sig-
nal, it changes the size automatically as indicated below:
When the TV is receiving VPS code 16:9 the TV selects
CINEMA automatically.
When the TV is receiving VPS code 14:9 the TV selects
ZOOM 14:9 automatically.
When the TV is receiving VPS code 4:3 the TV selects
NORMAL automatically.
Picture Mode
This item is used to change the picture mode. By pressing
or button you may choose one of these options:
When the TV does NOT receive VPS code the TV selects
FULL automatically.
BRIGHT, STANDARD, SOFT, MANUAL.
External source: When you are watching the TV set
through the Euro-SCART AV-1 terminal and it receives infor-
mation of 16:9 format (through the audio-video control pin)
the TV selects FULL automatically.
Wide Mode (Special detail information)
Special detail information about FULL, NORMAL, ZOOM
14:9, CINEMA (16:9) and 16:9ZOOM S.
Colour Temp
FULL
Using or button select Colour Temp.
With Full Mode you adapt the picture 16:9 format while also
stretching the centre of view. This is an advantage, for exam-
ple, when watching sports games where there is no real fixed
centre of the picture.
This item is used to change the Colour Temperature. By
pressing or button you may choose one of these op-
tions: COOL, WARM, NORMAL.
Wide Mode :
NORMAL
Using or button select Wide Mode.
You can watch 4:3 programs in 4:3 format by switching to
NORMAL Mode function.
With this item you can select the width of the picture. By
pressing or button you may choose one of these op-
tions : AUTO, NORMAL, ZOOM 14:9, CINEMA, 16:9ZOOM S
or FULL.
Wide mode can be set by
wide mode button also.
ZOOM 14:9
Adapts the 14:9 broadcast cinema movies to the 14:9 Mode.
Each time you press the wide mode button
of the picture changes as indicated:
, the width
- 12 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H2S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer
CINEMA (16:9)
The sleep timer is used to turn the TV off after a defined peri-
od. Press or button to choose a period of time after
selecting this item. The timer can be programmed between
Off and 120 minutes in steps of 10 minutes. (OFF, 010, 020,
030, 040, ......... ,120.)
Adapts the 16:9 broadcast cinema movies to the 16:9 Mode,
thereby getting rid of the black borders.
If sleep timer is activated, at the end of the selected the time,
the TV goes automatically to stand-by mode.
16:9ZOOM S
Adapts up to the wide picture (16:9 aspect ratio) with subtitle
to the full screen.
Child lock:
You can disable the control panel buttons (except the POW-
ER button) with this item.
Press or button to change the setting to On or Off af-
ter selecting this item.
When you set this item to On, the TV can be operated only
by using the remote control handset.
Adjusting the visible area of the picture:
If subtitles or the top (or bottom) of the picture are cut off,
you can adjust the visible area of the picture manually.
1. Press Wide mode
button once.
The WIDE MODE indicator appears. The WIDE MODE
will not be changed.
Language:
Menu Language can be selected by pressing or but-
ton on Language item.
2. While it is displayed, press or to change the po-
sition of the picture.
You cannot adjust the visible area in NORMAL or FULL mode.
To Store the Settings
Setting External Source Output
Press or button on STORE option to store Picture
menu settings or press OK button.
You can use this menu to select the internal or external
source that will be output at EXT-2 terminal.
In the Feature menu select EXT-2 Output using or
button. Then select the source you want to be output
at EXT.2 pressing or button (one of the sources: TV,
EXT-1, F-AV.
Auto Store:
Wide mode is stored automatically.
Feature Menu
Blue Background During No-Signal
Press M button, now you are in main menu. In the main
menu, select FEATURE, using or button. Then enter
the feature menu pressing or button.
The Blue Background feature can be set by or but-
ton to either On or Off.
- 13 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H3S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL. (Installation) Menu
select CHANNEL again, and press or button to
select the channel number, or enter the number with the
digit buttons.
You can store a channel manually, or modify the current set-
tings of a channel (for example, fine-tuning a channel).
You can also change the colour system.
5. If the picture is not clear or no colour appears, change the
colour system to display the picture normally. Press
Press M button to display the main menu.
or button to select COLOUR SYSTEM, then press
or button to choose the correct one.
In TV mode: PAL / SECAM
Press or button to select INSTALL. item. Then
or button to display the INSTALL. menu.
In AV mode: AUTO / PAL / SECAM / NTSC 3.58 /
NTSC 4.43
6. If the channel reception is poor, fine-tune the channel.
Press or to select FINE TUNING, then press
or button to fine-tune the channel.
7. After the all settings are completed, store the new
channels setting to the programme number which you se-
lected. Press or to select STORE, then press
Note:
or button to store it.
If you want to modify the current settings of a channel, se-
lect the channel of which you want to modify the setting.
Then display the main menu on screen.
In AV mode, you can change only the COLOUR SYSTEM
item.
1. PROGRAMME is the first selected item as you enter the
INSTALL. menu. Press the or button to select the
programme number where you want the tuned channel to
be stored. (You may also type the programme number us-
ing the digit buttons)
8. When you select "Frequency Search" , the display of the
Tuning menu will be as below :
Note:
Do not use the PROGRAMME item when you want to
modify the current programme number setting as this may
cause other programmes to be changed that are in the ex-
isting programme number.
2. Press or button to select Tuning Mode. By press-
As "Frequency Search" is selected, TV will search ac-
cording to the channel frequencies.
ing or button , you can select the mode in which
you want the search to be made, "Channel Search"
mode or "Frequency Search" mode.
With the or button, select Search. Search can be
made either forward, pressing button or backwards,
pressing button.
When you select "Channel Search" ("Channel" will be
displayed in the menu.), the display of the
INSTALL.(Installation) Menu will be as below :
The search will be done with steps of 0.25MHz. in each
step.
If the tuned station is not the desired one, you can continue
searching pressing or button again.
When the desired station is tuned, select STORE using
or button and store it to the programme number
you selected pressing or button or press OK but-
ton.
Now as you had selected the Frequency Search, the tuning
mode of the program is stored as Frequency Search Mode.
Direct Frequency Access
3. Press or button to select BAND. Using or
button to select the band in which you want to search a
channel.
If you know the broadcast band and the channel frequency
of the station you want to tune, you do not need to make
search; select Frequency, using or button in the
Frequency Mode Tuning Menu. You can type the first 3 dig-
its of the frequency using the digit buttons, and then you
4. Press or button to select SEARCH. Press or
button to start searching. (Press button to search
forward. Press to search backwards.)
If the found channel is not the desired one, press or
button to start searching again.
can select the decimal part of the frequency by using or
To stop searching before a channel is found, press the
reverse direction button. For example, when the TV is
searching forward with button, press button to
stop searching.
buttons with 250kHz steps. For example if you want to
tune the station at frequency 224.25 MHz; first you can di-
rectly type 224. The bar at bottom of the menu will show
224.00 . Then by increasing or decreasing with 0.25 MHz
steps using or buttons, you can select the
224.25MHz .When you type and select the frequency, the
corresponding station will be displayed.
If you know the channel number which you want to find,
you can find the channel directly. Follow the step 5 to
select the correct standard, then press or to
- 14 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H4S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
To store the station to the programme number selected, se-
lect STORE option using or button and then press
To change the programme number of a channel
(INSERT):
or button or press OK button.
1. Choose the channel you want to change the programme
number.
2. Press the GREEN button to enter the INSERT mode.
Now as you had selected the Frequency Search, the tuning
mode of the program is stored as Frequency Search Mode.
Note : Channel Search Tuning Mode uses a channel table.
The channels and stations at the table may vary from table to
table and from country to country. Each channel has an ex-
act frequency on the table.
3. Press / / / button to choose new
programme number.
4. Press the GREEN button to insert the channel to the cho-
sen programme number.
Frequency Search Tuning Mode does not use a channel
table and it is slower than Channel Search Tuning Mode.
To cancel this INSERT mode, press the BLUE button.
To start A.P.S (AUTOSTORE)
Channel Search Tuning Mode is recommended for the
countries which uses standard channel table.
A.P.S. automatically programmes the received channels in
your TVs programme numbers.
Frequency Search Tuning Mode recommended for the
countries which uses non-standard channel table.
1. Press the BLUE button to enter the AUTOSTORE mode.
A warning message appears.
Program. (Programming) Menu
You can use the Program. (Programming) menu to delete a
channel, to change the programme number of a channel, to
give a channel name to a channel, and to start the A.P.S
(AUTOSTORE) function.
Press M button to display the main menu.
Press or button to select PROGRAM. item, then
or button to display the PROGRAM. menu.
To cancel the AUTOSTORE mode, press the
but-
ton.
2. Press or button to choose the COUNTRY, then
press or button the choose country you are now lo-
cated.
3. By pressing the up and down buttons, come to the Tuning
Mode item and select the mode at which your TV will run
the APS.
4. Press or button to choose the CONTINUE, then
press button to start A.P.S. The following message ap-
pears.
To choose a channel in the PROGRAM. menu:
Press / / / button. The programme number
that you choose is high-lighted in the PROGRAM. menu
and you can view the picture of that channel.
To cancel the A.P.S., press the
button.
Caution:
5. After A.P.S. is finalized, the PROGRAM. menu appears
again.
Using the DELETE or INSERT function it is possible to re-
write the current channel list in the PROGRAM menu. This
can cause other channels to be changed if they were former-
ly in locations affected by this function.
To give a channel name (NAME):
1. Choose the channel you want to give a channel name.
2. Press the RED button to enter the NAME mode.
3. Press or button to choose the position, and press
or button to choose each character of channel
name.
4. Press the RED button to store the channel name.
To cancel the NAME mode, press the BLUE button.
To delete a channel (DELETE):
1. Choose the channel you want to delete.
2. Press the YELLOW button to enter the DELETE mode.
3. Press the YELLOW button to delete it.
To cancel this DELETE mode, press the BLUE button.
- 15 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H5S-AK45-SHARP-TV-1.p65
21.01.2004, 08:28
Download from Www.Somanuals.com. All Manuals Search And Download.
To select a page of Teletext
Other Features
Press the appropriate digit buttons for the required Teletext
page number.
Sound Mute
The selected page number is displayed at the top left corner
of the screen. The Teletext page counter searches until the
selected page number is located, so that the desired page is
displayed on the screen.
To cut off the sound from the TV press button. To restore
the sound press the button again or use the
buttons, in this case the volume will start from minimum
setting.
+ or -
Press button to move the Teletext screen forward one
page at a time.
Stereo / Bilingual
Press button to move the Teletext screen backward
one page at a time.
If the TV channel you are watching broadcasts in two lan-
guages (e.g. Eurosport), you can select the dubbed or the
original language, pressing the I-II button.
When the stereo broadcast is received poorly, you can
change from stereo to mono sound so that you can hear
the broadcast more clearly and easily.
Information on Screen
First pressing the
button displays the current status
Programme number,Station name and Sound
mode.
To Display the Time
While watching a TV programme with Teletext transmission
press button. The current time information, captured
from Teletext will be displayed at the upper right corner of
the screen.
To Select Index Page
If the programme being watched does not have Teletext
transmission, no time information will be displayed.
To select the page number of the index (generally page
100), press button.
The time information will disappear after pressing but-
ton again.
To Select Teletext with a TV Programme
Press button. The text is now superimposed over the
programme on the screen.
Flash back (
)
This button is used to return to the previous viewed preset.
Press button again to return to the Teletext page.
By pressing the " " button repeatedly it is possible to tog-
gle between two presets.
Searching for a page while watching TV
To search for a specific page whilst viewing the TV picture,
whilst viewing teletext enter the desired Page number,
Teletext
then press the
button will restore the TV picture. Once
Teletext is an information system that displays text on your
TV screen. Using the Teletext information system you can
view a page of information on a subject that is available in the
list of contents (index).
the desired page is found the Header of this page will ap-
pear on the screen. Press the button to view the full
page.
No on screen display will be available in text mode.
No contrast, brightness or colour control, but volume control
is available in text mode.
To Select Double Height Text
Press button for the top half of the information page to
be displayed in double height text.
To operate Teletext
Press button again for the bottom half of the informa-
tion page to be displayed in double height text.
Select a TV station on which Teletext is being transmitted.
Press (TELETEXT) button. Usually the list of contents Press button once more for the full page of normal
(index) is displayed on the screen.
height text.
To Reveal concealed Information
Pressing button once will reveal answers on a quiz or
games page.
Pressing button again will conceal the revealed an-
swers.
To Stop Automatic Page Change
The teletext page you have selected may contain more infor-
mation than can be displayed on one screen, in such cases
the page will uptade periodically.
- 16 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H6S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Press button to stop the automatic page change.
RGB mode
Press button again to allow the next page to be dis-
played.
If a piece of equipment outputs RGB signals use the EXT-1
Euro connector as this is RGB ready.
To Select a Subcode Page
Via the RCA jacks
Subcode pages are subsections of long Teletext pages that
can only be displayed on the screen one section at a time.
If you have an equipment (such as a Camcorder) which has
the RCA jacks, connect it to the Front AV (F-AV) terminal
with the video and audio cables.
Select the required Teletext page.
Press button.
If the equipment has the mono audio jack, connect it to the
AUDIO-L jack.
Select the required subcode page number by pressing four
digit buttons (e.g. 0001).
Via the ANT (aerial) socket
If the selected subcode page is not displayed in a short
time, press button. TV programme will be displayed on
the screen.
If your equipment does not have an Euroconnector or RCA
jacks, connect it to the TV with an aerial cable. For details,
see the manual provided with the equipment.
Teletext page number will be displayed on the upper left
corner of the screen when the selected page is found.
To store the test signal that comes from the equipment,
see INSTALL. Menu on page 14 and store it to the pro-
gramme number 0. You can watch images from that equip-
ment to select the programme number which you stored the
test signal.
Press button to display the selected Teletext page.
TV and Video Recoder (VCR)
Connect the Video Recorder to the ANT (antenna input)
socket of the TV with the aerial cable.
Connect the Video Recorder to the EXT.1 or EXT.2 terminal
with the SCART cable, or connect it to the Front AV (F-AV)
terminal with the audio and video cables.
NTSC Playback
Fastext
Connect a NTSC video recorder to a terminal. Then press
button to select the corresponding AV mode.
Teletext mode will be selected according to transmission au-
tomatically.
NTSC 3.58/4.43 system is detected automatically in AV
mode.
Your TV supports the 7 page Teletext system. When the
page number of any of the 7 pages in memory is entered, the
system will not search for the requested page; instead it will
display the page automatically.
Copy Facility
You can output the video and audio signals which inputs from
TV or EXT.1(EXT-1) terminal to the video recorder connected
to the EXT.2(EXT-2)terminal.
Press button to move the Teletext screen forward one
page at a time.
To select the output source, see Setting External
Source Output on page 13.
Press button to move the Teletext screen backward
one page at a time.
To connect to S-VHS input
For Fastext
Connect your camera or camcorder at the front or back side
of your TV.
The subject-heading for the information may have a particular
colour or can be in a form located in a coloured box.
Connect your equipment to the TV via S-VHS input and au-
dio inputs of F-AV inputs by using S-VHS cables.
Press an appropriate RED, GREEN, YELLOW or BLUE but-
ton in order to reach the relevant page quickly.
Connecting Headphones
To exit Teletext
Use the stereo headphone socket of your TV, to connect
headphones.
Press
button. The screen will switch to TV mode.
Connecting external equipment
Via the Euro connector
You TV set has two euro connector sockets. If you wish to
connect external equipment (e.g. video recorder, decoder,
etc.) which have Euro connectors, to your TV, use the EXT.1
(EXT-1) orEXT.2(EXT-2) terminals.
If an external device is connected via Euro connector sockets
the TV will be switched to AV mode automatically.
- 17 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H7S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting external equipment
Before connecting anything
Switch off all equipment.
Read the manuals provided with the equipments.
To select anAV mode
Pressing
button on the remote control selects one of AV modes (EXT-1, RGB, EXT-2, F-AV, SVHS)
To return to the TV mode, repeatedly press
button.
EXT.1(EXT-1)terminal: Euroconnector (21-pin, SCART)
Video input, Audio L/R inputs and RGB inputs are available.
TV broadcast outputs (Video and Audio L/R) are available.
EXT.2(EXT-2)terminal: Euroconnector (21-pin, SCART)
Video input and Audio L/R inputs are available.
Video and Audio L/R outputs are available. (see Setting External Source Output on page 13.)
Front AV (F-AV) terminal: RCA connectors x 3 and S-VIDEO (Y/C) connector
Video input and Audio L/R inputs are available.
S-VIDEO input is available.
$QWHQQD
(;7ꢀꢁ
&DPFRUGHU
(;7ꢀꢂ
$XGLR
+HDGSKRQH
9LGHR
'HFRGHU
)RUꢀ6DWHOOLWHꢀ5HFHLYHU
- 18 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H8S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Connections
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ$HULDOꢀFRQQHFWLRQꢀꢁꢀ79ꢀVHWꢀRQO\ꢀꢁ
ꢀ$HULDOꢀ&RQQHFWLRQVꢀꢁꢀ79ꢀDQGꢀ9&5ꢀꢁ
Note: For further details, please refer to operation manual of your VCR.
- 19 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV1H9S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Connections (Continued)
&RQQHFWLRQV ꢀ 79ꢁ '9' 3OD\HUꢁ '(&2'(5 DQG 9&5 ꢂ9LGHRUHFRUGHUꢃ ꢀ
Note: For further details, please refer to operation manuals of your DVD Player, DECODER and VCR.
- 20 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H0S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Connections (Continued)
&RQQHFWLRQV ꢀ 79ꢁ '9' 3OD\HU DQG 'LJLWDO 6HW 7RS %R[ ꢀ
Note: For further details, please refer to operation manuals of your DVD Player and Digital Set Top Box.
- 21 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H1S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Connections (Continued)
&RQQHFWLRQV ꢀ 79ꢁ '9' 3OD\HUꢁ 9&5 DQG 'LJLWDO 6HW 7RS %R[ ꢀ
Note: For further details, please refer to operation manuals of your DVD Player, VCR and Digital Set Top Box.
- 22 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H2S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Connections (Continued)
)URQWꢀFRQQHFWLRQVꢀꢁ79ꢀDQGꢀ9LGHRꢀFDPHUDꢁ
&RQQHFWLRQꢀ79ꢁSRZHUꢁFDEOHꢁWRꢁDꢁꢂꢂꢃꢁaꢁꢂꢄꢃꢁ9ꢁV\VWHPꢁꢀ
ꢀ0DLQVꢀ6RFNHWꢀ2XWOHW
$&ꢀꢁꢁꢂaꢁꢃꢂꢀ9ꢄꢀꢅꢂꢀ+]
Note: For further details, please refer to operation manual of your Video Camera.
- 23 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H3S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
21-pin Euro-SCART and 21-pin Audio/Video
REAR TV
RF Input
1. Aerial terminal
21-pin In/Out
2. 21-pin Audio/Video (RGB) (AV-1) With
PAL/SECAM/NTSC Video Input
3. 21-pin Audio/Video (AV-2) With
PAL/SECAM/NTSC Video Input
ꢀ
ꢁ
ꢂ
21-pin Euro-SCART (AV-1) (EXT.1)
1. Audio right output
2. Audio right input
3. Audio left output
4. Common earth for audio
5. Earth for blue
8. Audio-video control
9. Earth for green
10. Not used
15. Red input
16. Red/Green/Blue control
17. Earth for video
11. Green input
12. Not used
18. Earth for Red/Green/Blue control
19. Video output
6. Audio left input
7. Blue input
13. Earth for red
14. Not used
20. Video input (PAL/SECAM/NTSC)
21. Plug shield
21-pin Audio/Video (AV-2) with Input (EXT.2)
1. Audio right output
2. Audio right input
3. Audio left output
4. Common earth for audio
5. Earth
8. Audio-video control
9. Earth
15. Not used
16. Not used
10. Not used
11. Not used
12. Not used
13. Earth
17. Earth for video
18. Earth
19. Video output
20. Video input (PAL/SECAM/NTSC)
21. Plug shield
6. Audio left input
7. Not used
14. Not used
- 24 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H4S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If the fault cannot be corrected by using this guide, remove the mains plug from the wall socket and contact the dealer or
supplier from whom it was purchased. Where this is not possible, please visit our web-site at www.sharp.co.uk/support.
Customers without Internet access may telephone 08705 274277 [or (01) 676 0648 if telephoning form Ireland] during office hours.
Certain replacement parts and accessories may be obtained from our Main Parts Distributor, who can be contacted on
the following numbers:
Willow Vale Electronics Ltd. 0121 766 5414 and 0161 205 7531
In the unlikely event of this equipment requiring any repair during the guarantee period, you will need to provide proof of the
date of purchase to the repairing company. Please keep your invoice or Receipt, which is supplied at the time of purchasing.
- 25 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H5S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TV BROADCASTING
PAL I/I
RECEIVING CHANNELS
VHF (BANDI/III)
UHF (BAND U)
HYPERBAND
Cleaning The Screen
Your TV is fitted with a True Flat" picture tube. The
surface of the screen is covered with a foil. Under
no circumstances may this be damaged.
CABLE-TV
To clean
NUMBER OF PRESET CHANNELS
Clean the laminated screen with a soft cotton
cloth. Only non-alkaline, thinned soapsuds on a
basis of water or alkohol be used to moisten the
cloth. Rub the surface gently with the cloth until
the surface is completely dry.
100
CHANNEL INDICATOR
ON SCREEN DISPLAY
Under no circumstances...
RF AERIAL INPUT
may the screen be wiped with conven tional glass
cleaning fluid.
75 Ohm Unbalanced
may the screen be brought into contact with abra-
sive materials.
OPERATING VOLTAGE
may soiling be renoved by polishing or scouring.
220-240V AC, 50 Hz.
To clean off sticky substances, the cloth can
be moistened with acetone.
POWER CONSUMPTION (W) (28LF-92H)
95 Watt
Under no circumstances clean with this ace-
tone cloth the TV-Cabinet.
POWER CONSUMPTION (W) (32LF-92H)
Power Consumption at (Stand-by)
< 3 Watts
Audio Output (RMS):
2x10 W
AUDIO OUTPUT
Nicam Stereo
PICTURE TUBE
28 16:9
32 16:9
Safety
CE - MARK
EMC
CE - MARK
DIMENSIONS (DxLxH) (mm) (28LF-92H)
',0(16,216
'
/
+
:HLJKWꢀꢁNJꢂ
ꢀꢁꢂ
ꢃꢄꢂ
ꢅꢆꢀ
ꢇꢆ
DIMENSIONS (DxLxH) (mm) (32LF-92H)
',0(16,216
'
/
+
:HLJKWꢀꢁNJꢂ
ꢀꢁꢂ
ꢃꢄꢂ
ꢀꢀꢅ
ꢀꢆ
- 26 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H6S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Instructions
For your own safety read following instruction carefully before attempting to connect this unit to the mains sup-
ply.
MAINS (AC) OPERATION
The wires in this mains lead are coloured in accordance with the following code :
BLUE-NEUTRAL
BROWN-LIVE
IMPORTANT
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the
letter L or coloured red.
No connection is to be made to the earth terminal of the plug.
If a 13 Amp (BS 1363) Plug is used a 5 Amp Fuse must be fitted, or if any other type of Plug is
used a 5 Amp Fuse must be fitted, either in the Plug of Adaptor, or on the Distribution Board.
CAUTION
TO PREVENT ELECTRIC SHOCK DISCONNECT FROM THE MAINS BEFORE REMOVING COVER. NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SAFETY PRECAUTION
THIS EQUIPMENT MUST BE DISCONNECTED FROM THE MAINS WHEN NOT IN USE. DO NOT ALLOW
THIS UNIT TO BE EXPOSED TO RAIN OR MOISTURE.
- 27 -
ENG-2862W-3262W-1548UK-2SCART-FAV-SV2H7S-AK45-SHARP-TV-2.p65
21.01.2004, 08:29
Download from Www.Somanuals.com. All Manuals Search And Download.
R
SHARP CORPORATION
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath,
Manchester M40 5BE
50048416
12/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|