AL-1552
AL-1553
AL-1555
DIGITAL MULTIFUNCTIONAL SYSTEM
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
Caution label on the unit
The label (
) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using
Follow the cautions below when using this unit.
Warning:
• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.
• Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15
seconds before turning it back on.
• Unit power must be turned off before installing any supplies.
Caution:
• Place the unit on a firm, level surface.
• Do not install the unit in a humid or dusty location.
• When the unit is not used for a long time, for example for consecutive holidays,
turn the power switch off and remove the power cord from the outlet.
• When moving the unit, be sure to turn the power switch off and remove the power
cord from the outlet.
• Do not cover the unit with a dust cover, cloth or plastic film while the power is on.
Doing so may prevent heat radiation, damaging the unit.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the unit and shall be easily accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the
20cm
machine for servicing and proper ventilation.
10cm
10cm
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions on handling
Be careful in handling the unit as follows to maintain the performance of this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Do not expose the drum cartridge to direct sunlight.
• Doing so will damage the surface (green portion) of the drum cartridge, causing
smudges on copies.
Store spare supplies such as drum cartridges and TD cartridges in a dark
place without removing from the package before use.
• If they are exposed to direct sunlight, smudges on copies may result.
Do not touch the surface (green portion) of the drum cartridge.
• Doing so will damage the surface of the cartridge, causing smudges on copies.
Cautions on laser
Wave length
Pulse times
Output power
770 nm – 795 nm
11.82 µs / 7 mm
0.17 mW 0.01 mW
Trademark acknowledgements
• Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A. and
other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
Products that have earned the ENERGY STAR® are designed
to protect the environment through superior energy efficiency.
In some areas, the "POWER" switch positions are marked "I" and "O" on the copier
instead of "ON" and "OFF".
The symbol "O" denotes the copier is not completely de-energized but in a stand-by
condition at this "POWER" switch position.
If your copier is so marked, please read "I" for "ON" and "O" for "OFF".
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1 INTRODUCTION
5 MAKING COPIES
USING THE MANUALS................. 4
PART NAMES................................ 5
OPERATION PANEL...................... 6
COPY FLOW................................46
ORIGINAL PLACEMENT.............47
SET THE COPY QUANTITY........49
EXPOSURE ADJUSTMENT/
1
2
3
4
5
6
7
8
9
PHOTO COPYING.......................49
REDUCTION/ENLARGEMENT/
ZOOM ..........................................51
SELECTING THE TRAY
2 SETTING UP THE UNIT
SETUP PROCEDURE................... 7
CHECKING PACKED
COMPONENTS AND
ACCESSORIES............................. 8
PREPARING THE UNIT FOR
INSTALLATION.............................. 8
INSTALLING THE TD
CARTRIDGE................................ 10
CONNECTING THE POWER
CORD .......................................... 12
(AL-1553, AL-1555) ...................51
6 SPECIAL FUNCTIONS
TWO SIDED COPYING ...............52
DESCRIPTION OF SPECIAL
FUNCTIONS................................54
TONER SAVE MODE ..................54
USER PROGRAMS .....................55
DISPLAYING TOTAL NUMBER
3 LOADING PAPER
OF COPIES .................................56
PAPER......................................... 14
LOADING THE PAPER TRAY ........ 15
BYPASS FEED
7 MAINTENANCE
(including special paper).............. 17
TD CARTRIDGE
REPLACEMENT ..........................57
DRUM CARTRIDGE
REPLACEMENT ..........................58
CLEANING THE UNIT.................59
4
INSTALLING THE SOFTWARE
SOFTWARE FOR THE SHARP
PERSONAL MFP SERIES .......... 19
HARDWARE AND SOFTWARE
REQUIREMENTS........................ 20
BEFORE INSTALLATION ............ 20
INSTALLING THE SOFTWARE... 22
INDICATORS ON THE OPERATION
PANEL ......................................... 32
USING THE PRINTER MODE..... 33
USING THE SCANNER MODE... 35
HOW TO USE THE ONLINE
8
TROUBLESHOOTING THE UNIT
TROUBLESHOOTING.................61
STATUS INDICATORS.................62
MISFEED REMOVAL...................63
9 APPENDIX
SPECIFICATIONS .......................68
ABOUT SUPPLIES AND
OPTIONS.....................................70
MOVING AND STORING
MANUAL...................................... 43
USING OTHER INSTALLED
DRIVERS..................................... 44
CONNECTING THE
THE UNIT ....................................71
INTERFACE CABLE.................... 45
INDEX..........................................72
SOFTWARE LICENSE ................75
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This chapter provides basic information for using the unit.
1
USING THE MANUALS
In addition to this printed manual an online manual is also provided. To get full use of all
features and functions of this product, be sure to familiarise yourself with both manuals.
This printed manual provides all installation and setup instructions as well as instructions
in the use of all copier functions. The online manual contains the following information.
Online manual
Provides you with information on how to specify preferences and troubleshooting. Check
the online manual when you use this unit after all the initial setup is completed.
How to use the online manual
Explains how to use the online manual.
Print
Provides information on how to print a document.
Scan
Explains how to scan using the scanner driver and how to adjust the settings for
the Button Manager.
Troubleshooting
Provides instructions on how to solve driver or software problems.
Conventions used in this manual and online manual
• This operation manual explains the operation of the AL-1552, AL-1553 and AL-
1555 models. In cases where the operation is the same, the AL-1555 is used.
• Illustrations of driver screens and other computer screens show the screens that
appear in Windows XP Home Edition. Some of the names that appear in these
illustrations may differ slightly from the screens that appear in other operating systems.
• This operation manual refers to the Single Pass Feeder as the "SPF", and the
Reverse Single Pass Feeder as the "RSPF".
• In this manual, the following icons are used to provide the user with information
pertinent to the use of the unit.
Warns the user that injury may result if the contents of the warning
are not properly followed.
Cautions the user that damage to the unit or one of its components
may result if the contents of the caution are not properly followed.
Notes provide information relevant to the unit regarding
specifications, functions, performance, operation and such, that
may be useful to the user.
Indicates a letter displayed in the display.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAMES
SPF (AL-1553)
RSPF (AL-1555)
Original cover
(AL-1552)
Original guide
Feeding
roller cover
1
Original
Original feeder tray
exit area
Interface
USB
interface
Parallel
interface
SPF (AL-1553)
RSPF (AL-1555)
scan area
1
2
5
8
9
6
7
3
4
10
11
Multi-bypass
12
Paper tray 2
(AL-1555)
tray
(AL-1553, AL-1555)
TD cartridge
Drum cartridge
Single bypass
(AL-1552)
7
5
13
3
14
15
Power switch
10
11
12
13
Original table
Operation panel
Front cover
Paper tray
1
2
3
4
5
Handle
Power cord socket
Fusing unit release lever
Transfer charger
Charger cleaner
14
15
Side cover
Side cover open button
Bypass paper guides
Paper output tray
6
7
8
9
Paper output tray extension
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION PANEL
AL-1555
141
A5
A4
A4 B5
86
70
A4
A5
Copy ratio display (%) key (p.51)
Display
Displays the specified copy quantity,
zoom copy ratio, user program code,
and error code.
SCANNER key and indicator
ONLINE key and indicator (p.32)
Lights up when the unit is used as a
printer and scanner. For description of
the ONLINE indicator, see
8
9
Original to copy key and indicators
Two-sided copies from
one-sided originals.
1
Turn on Long Edge or
Turn on Short Edge
can be selected.
10
11
Two-sided copies from
two-sidedoriginals. (Can
be selected only when
the RSPF is used.)
(AL-1555)
Single-sided copies
from two-sided
Power save indicator
12
13
14
15
originals. (Can be
Lights up when the unit is in a power
selected only when the
RSPF is used.)
Paper feed location indicators
Light up to show the selected paper
feed station.
(AL-1555)
Exposure mode selector key and
indicators
Use to sequentially select the exposure
modes: AUTO, MANUAL or PHOTO.
Selected mode is shown by a lit
indicator. (p.49)
Light and dark keys and indicators
Use to adjust the MANUAL or PHOTO
exposure level. Selected exposure level is
and terminate user program setting. (p.55)
Alarm indicators
2
Tray select key (AL-1553, AL-1555)
Use to select a paper feed station
ZOOM keys and indicator
Use to select any reduction or
enlargement copy ratio from 25% to
Copy quantity keys
3
4
16
17
• Use to select the desired copy
• Use to make user program entries.
Drum replacement required
indicator (p.58)
Clear key
Misfeed indicator (p.63)
• Press to clear the display, or press
during a copy run to terminate
copying. (p.49)
TD cartridge replacement
required indicator (p.57)
• Press and hold down during standby
to display the total number of copies
made to date. (p.56)
Copy ratio selector key and
indicators
Use to sequentially select preset
reduction/enlargement copy ratios.
Selected copy ratio is shown by a lit
indicator. (p.51)
5
6
7
Start key and indicator
18
• Copying is possible when the
indicator is on.
• Press to start copying.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP THE UNIT
Follow the installation procedure below to use the unit properly.
2
If the unit does not function properly during setup or use, or if a function
cannot be used, see "TROUBLESHOOTING THE UNIT" (p.61).
2
SETUP PROCEDURE
When using the unit for the first time, setup the unit following the procedure shown below.
1 Open the package, and make sure that all the accessories are
supplied with the unit. (p.8)
2 Remove the protective materials. (p.9)
3 Install the TD cartridge. (p.10)
4 Load the paper in the paper tray (p.15) or the multi-bypass
tray*1. (p.17)
5 Insert the attached power cord into the power cord socket at the
rear of the unit.
6 Connect the power cord. (p.12)
7 Install the software.*2 (p.19)
8 Connect the interface cable*2 (p.45) and turn on the unit. (p.12)
9 Now, you can copy (p.46), print (p.33), or scan (p.35) your
document.
1
*
*
The multi-bypass tray is only included with the AL-1553 and AL-1555.
If you are only using the unit for copying, skip this step.
2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING PACKED COMPONENTS AND
ACCESSORIES
Open the carton and check if the following components and accessories are
included.
If anything is not included or is damaged, contact your authorised service
representative.
Operation manual
AL-1552
AL-1553
AL-1555
Software CD-ROM
Drum cartridge
(installed in unit)
TD cartridge
PREPARING THE UNIT FOR INSTALLATION
Be sure to hold the handles on
1
both sides of the unit to unpack
the unit and carry it to the
installation location.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove all pieces of tape shown in the illustration below. Then
open the original cover/SPF/RSPF and remove protective
materials. After that, take out the bag containing the power
cord and TD cartridge.
2
(AL-1555 only)
(AL-1555)
2
AL-1552
AL-1553, AL-1555
AL-1553, AL-1555
AL-1552
Release the scan head locking switch.
3
The scan head locking switch is under the original table.
If the switch is locked ( ), the unit will not operate. Unlock the switch (
as shown below.
)
Grasp here and turn in
the direction of the arrow.
Lock
Unlock
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE TD CARTRIDGE
Open the multi-bypass tray
1
and then open the side
cover.
Push gently on both sides of the
front cover to open the cover.
2
Remove the TD cartridge from the bag. Hold the cartridge on
3
both sides and shake it horizontally four or five times. Hold the
tab of the protective cover and pull the tab to your side to
remove the cover.
4 or 5 times
Gently insert the TD cartridge
4
until it locks in place while
pushing the lock release button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the front cover and then
the side cover by pressing the
round projections near the
side cover open button.
5
When closing the covers, be
sure to close the front cover
securely and then close the
side cover. If the covers are
closed in the wrong order, the
covers may be damaged.
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE POWER CORD
If you use the unit in a country other than the country where the unit was
purchased, you will need to make sure that your local power supply is
compatible with your model. If you plug the unit into an incompatible
power supply, irreparable damage to the unit will result.
Ensure that the power switch of
1
the unit is in the OFF position.
Insert the attached power cord
into the power cord socket at the
rear of the unit.
Plug the other end of the power cord into the nearest outlet.
2
Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.
Power on
Ensure that the power switch of the unit is in the OFF position. Plug the other end of
the power cord into the nearest outlet. Turn the power switch on the left side of the
unit to the "ON" position. The start ( ) indicator will light up and other indicators
which show the initial settings of the operation panel will also light up to indicate the
ready condition. For the initial settings, see the "Initial settings of operation panel"
described on the next page.
• The unit will enter a power save mode once the set time has elapsed
without any unit operation. The settings of the power save modes can
• The unit will return to the initial settings a preset amount of time after
the end of copy or scanner job. The preset amount of time (auto clear
time) can be changed. See "USER PROGRAMS" (p.55).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition
(when the start ( ) indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality. At this
time, the scan head moves automatically. This is normal and does not indicate unit
trouble.
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when
2
job is finished, or when the clear (
) key is pressed twice.
The initial settings of the operation panel are shown below.
AL-1555
A5 A4
A4 B5
141
86
70
A4
A5
"0" is displayed in the display.
When copying is begun in this state, the settings in the following table are used.
Copy quantity
Exposure adjustment
Zoom
1 copy
AUTO
100%
Tray
Paper tray
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power
machine will not be used for a long time, turn off the power switch and remove the
power cord from the outlet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING PAPER
Follow the steps below to load paper into the tray.
3
PAPER
For best results, use only paper recommended by SHARP.
Type of paper
Type of media
Size
Weight
feeding
2
Paper tray
Standard paper
A4
A5
56g/m to
80g/m
2
B5
Letter
Legal
Invoice
2
Single bypass/ Standard paper and
Multi-bypass thick paper
tray
A4
A5
A6
52g/m to
2
128g/m **
B5
B6
Letter**
Legal
Invoice
Special Transparency A4
media film
Letter
Envelope*
International DL
International C5
Commercial 10
Monarch
* Do not use non-standard envelopes, and envelopes that have metal clasps, plastic
snappers, string closures, windows, linings, self-adhesive, patches or synthetic
materials. Do not use envelopes that are filled with air or envelopes that have
labels or stamps attached. These will cause physical damage to the unit.
2
2
**For paper weighing from 104g/m to 128g/m , A4 is the maximum size that can be
fed through the single bypass or the multi-bypass tray.
• Special papers such as transparency film, labels and envelope must be fed one
sheet at a time through the single bypass or the multi-bypass tray.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING THE PAPER TRAY
Raise the handle of the paper tray
and pull the paper tray out until it
stops.
1
Remove the pressure plate lock. Rotate the pressure plate lock
in the direction of the arrow to remove it while pressing down
the pressure plate of the paper tray.
2
3
Store the pressure plate lock which has been removed in step 2.
To store the pressure plate lock, rotate the lock to fix it on the
relevant location.
3
Pressure plate lock
Adjust the paper guides on the paper tray to the copy paper
4
width and length. Squeeze the lever of paper guide A and slide
the guide to match with the width of the paper. Move paper
guide B to the appropriate slot as marked on the tray.
Paper
Paper
guide A
guide B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan the paper and insert it into the tray. Make sure the edges go
under the corner hooks.
5
Do not load paper above the maximum height line (
the line will cause a paper misfeed.
). Exceeding
Gently push the paper tray back into the unit.
6
• After loading paper, to cancel the blinking
copying, press the clear ( ) key. The
and the start ( ) indicator will light up.
without restarting
in the display will go out
• Be sure that paper is free of rips, dust, wrinkles, and curled or bent
edges.
• Make sure all the paper in the stack is the same size and type.
• When loading paper, ensure there is no space between the paper and
the guide, and check if the guide is not set too narrow causing the
paper to bend. Loading paper in these ways will result in document
skew or a paper jam.
• When not using the unit for an extended period, remove all paper from
the paper tray and store it in a dry place. If paper is left in the unit for
an extended period, the paper will absorb moisture from the air,
resulting in paper jams.
• When adding new paper to the paper tray, remove the old paper
already contained in the tray. Placing new paper on top of the paper
already contained in the tray may result in feeding two sheets at one
time.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BYPASS FEED (including special paper)
The multi-bypass tray (AL-1553, AL-1555) or the single bypass (AL-1552) can be used to
feed standard paper, transparency film, labels, envelopes, and other special purpose paper.
Paper measuring from A6 to A4 and in the weight range of 52
g g
/m2 to 128 /m2 can be used
in this tray. (For paper weighing from 104 g
g
/m2 to 128 /m2, A4 is the maximum size.)
• The multi-bypass tray (AL-1553, AL-1555) can hold maximum of 50
sheets of paper. (Capacity will vary depending on the type of paper
loaded.) The single bypass (AL-1552) can hold one sheet of paper.
• The original image must be smaller than the paper or media for
copying. If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
The multi-bypass tray (AL-1553, AL-1555)
Open the multi-bypass tray and extend the tray.
1
3
To close the multi-
bypass tray, perform
step 1 and then step
2 in the illustration
and push the round
projections at the
right of the tray until
they click.
Set the paper guides to the paper width. Insert the paper (print
face down) all the way into the multi-bypass tray.
2
Print face
• Paper must be fed narrow side into the feed slot.
•
Special papers such as transparency film ,labels and envelopes
must be fed one sheet at a time through the multi-bypass tray.
• When copying onto transparency film, remove each copy
promptly. Do not let copies stack up.
Press the tray select (
) key to select the multi-bypass tray.
3
17
Download from Www.Somanuals.com. All Manuals Search And Download.
The single bypass (AL-1552)
• If you insert a sheet of paper into the single bypass when multiple
quantity setting will change to "0" and only one copy will be made.
• When copying onto transparency film, remove each copy promptly. Do
not let copies stack up.
Select copy settings before you begin the copy job.
1
information on the print settings, see the online manual or the Help file for
the printer driver, and then begin printing from the single bypass.
Set the paper guides to the paper width. Insert a single sheet of
copy or print paper (print face down) into the feed slot of the
single bypass.
2
Using copy mode
When you insert the paper, the machine will automatically draw in the paper
and begin copying.
Using printer mode
After
appears in the display, wait until the Paper feed location indicator for
the single bypass illuminates and insert the paper. The machine will
automatically draw in the paper and begin printing.
Print face
(AL-1552)
Note for loading envelopes
• Envelopes must be fed narrow side into the feed slot one at a time.
• Do not use non-standard envelopes, and envelopes that have metal clasps,
plastic snappers, string closures, windows, linings, self-adhesive, patches or
synthetic materials. Do not use envelopes that are filled with air or envelopes that
have labels or stamps attached.
• Envelopes of which the surface is not flat because of embossing may cause the
copies/prints to become smudged.
• Under high humidity and temperature conditions the glue flaps on some
envelopes may become sticky and be sealed closed when copied/printed.
• Use only envelopes which are flat and crisply folded. Curled or poorly formed
envelopes may be poorly copied/printed or may cause misfeeds.
• Be sure to select either Com10, DL, C5 or Monarch on the paper size setting of
the printer driver. (For detailed information on printer driver, refer to the online
manual.)
• It is recommended that you perform a test copy/print before performing the actual
copied/printed job.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE
This chapter explains how to install the software that allows the AL-1552, AL-
1553 and AL-1555 to be used as a printer and scanner, and the procedures for
using the printer and scanner functions. The following term is used in this chapter.
4
CD-ROM
Means the supplied CD-ROM with the SHARP Personal MFP series software.
SOFTWARE FOR THE SHARP PERSONAL MFP
SERIES
The supplied CD-ROM includes software for this unit.
MFP driver
Scanner driver
Permits you to operate scanning function of this unit with TWAIN-compliant and
WIA-compliant application.
Printer driver
Enables you to use the printer function of this unit with your computer.
4
Print Status Window
The print state and information on current printing are displayed on the status
monitor window.
Sharpdesk
An integrated software environment that makes it easy to manage document and
image files and launch applications.
Button Manager
Button Manager enabling the SCANNER (
) key located on the unit.
The scanning feature is only available with Windows 98/Me/2000/XP
using a USB connection. For users running Windows 95/NT 4.0 or using
a parallel connection, only printing is available.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements in order to install the software.
Computer type
IBM PC/AT or compatible computer equipped with a
USB1.1* or bi-directional parallel interface (IEEE 1284)
1
2
Operating system* Windows 95, Windows 98, Windows Me, Windows NT
3
Workstation 4.0 (ServicePack 5 or later)* , Windows 2000
3
3
Professional* , Windows XP Professional* , Windows XP
3
Home Edition*
Display
800 x 600dots (SVGA) display with 256 colours (or better)
Hard disk free space 150MB or more
Other requirement An environment on which any of the operating systems listed
for hardware
above can fully operate
1
* Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP
Professional or Windows XP Home Edition preinstalled model with USB interface
equipped as standard.
2
* Printing is unavailable in MS-DOS mode.
3
* The administrator's authorisation is required to install this software using this installer.
BEFORE INSTALLATION
The following table shows the drivers and software that can be installed for each
version of Windows and interface connection method.
MFP Driver
Button
Manager
Printer driver/
Print Status
Window
Sharpdesk
Scanner driver
Users of Windows
98/Me/2000/XP who
will use the USB
interface connection
Users of Windows
98/Me/2000/XP who
will use the parallel
interface connection
Windows 95/NT 4.0
users
Available
Available
Available
1
Available*
Not
Available
2
Not Available
Available*
1
* When the unit is connected through the parallel port, the Print Status Window can only
be used when the parallel port is set to ECP mode. To set the parallel port mode, refer
to your computer manual or ask the manufacturer of your computer.
2
* Sharpdesk can be installed when using a parallel interface connection, however, the
unit’s scanner function cannot be used.
Is there another GDI printer driver or a Windows Printing System printer
driver already installed? If installed, change the printer port setting. For
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Flow of installation
Refer to the following table and then begin installation.
Operating
Interface
Reference pages for how to install
Installing onto Windows XP (USB/parallel interface)
system
USB/
Parallel (p.22)
Windows XP
USB
Parallel
USB
Installing onto Windows 98/Me/2000 (USB interface) (p.26)
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.29)
Installing onto Windows 98/Me/2000 (USB interface) (p.26)
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.29)
Installing onto Windows 98/Me/2000 (USB interface) (p.26)
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.29)
Windows 98
Windows Me
Windows 2000
Parallel
USB
Parallel
Windows 95/
NT 4.0
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface) (p.29)
Parallel
4
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE
The following term is used in this section.
MFP
Means the unit as a printer and scanner.
• For this description, it is assumed that the mouse is configured for
right hand operation.
• To print or scan, the MFP must be in the online state.
• The scanner feature only works when using a USB interface cable.
• If any error message appears, solve the problem following the
instructions on the screen. After your problem is solved, the installing
procedure will be continued. Depending on your problem, you may
have to exit the installer. In this case, click the "Cancel" button to exit
the installer. After solving your problem, reinstall the software from the
beginning.
Installing onto Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not
connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
2
When any of "Found New Hardware Wizard" messages appear during
the software installation, be sure to click the "Cancel" button.
Double-click the "setup" ( ) icon.
3
If the language selection screen appears after you double click the
"setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
Select the software packages to be
installed, and then click the "Next"
button.
The software packages with checkmark (
on the list on the screen will be installed.
4
)
Click the "Display README" button to show
the information on the selected package.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are using the parallel interface connection, do not select the
Button Manager checkbox because this feature is not supported with
the parallel interface.
• If the following screen appears, click the "OK" button. Review the
appropriate the software packages to be installed.
Review the software packages to be
installed on the screen, and then click
the "Start" button.
The software packages to be installed will be
displayed on the screen. If inappropriate
packages are displayed, click the "Back" button
to select appropriate packages again.
5
6
4
Copying files for MFP driver installation (This step will start if it
was selected in step 4).
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the USB or parallel
interface cable is not connected to the MFP. Make sure that the
interface cable is not connected and click the "Next" button.
2
Click the "Next" button in the dialog box to
install the MFP driver or Cancel to quit the
installation.
3
The setup program will start to copy the files.
If the following screen appears while the files are
being copied (the message may appear more
than once), click "Continue Anyway".
When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
4
The Button Manager installer will start.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Button Manager (This step will start if it
was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
Read the message in the "Please read the following information."
window, and then click the "Next" button.
2
When a message appears that lets you specify the location for the
software to be installed, click the "Next" button.
3
If the program displays "Do you want the Button Manager added to
Windows Startup?", check "Yes" and click the "OK" button.
4
The setup program will start to copy the files.
Click the "Finish" button when the message informs you that
setup is successful.
5
The Sharpdesk installer will start.
Begin installation of the Sharpdesk (This step will start if it was
selected in step 4).
8
9
After confirming the message in the "Welcome to Sharpdesk
installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
The setup program will start to copy the files.
Click the "Finish" button when the message informs you that
Setup is complete.
5
Click the "Close" button when the
message informs you that "Setup has
finished". When the "Now connect the
MFP interface cable to the PC" dialog
box appears, click the "OK" button.
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure that the power of the MFP is turned on, and then
connect the USB interface cable or parallel interface cable.
Windows will detect the MFP and the Plug and Play screen will appear. If
you are using Windows XP with the parallel interface, go to step 12.
10
11
Begin installation of the scanner driver.
"SHARP AL-xxxx" (where xxxx is the model name of your MFP)
1
will appear in the "Found New Hardware Wizard" dialog box.
Select "Install the software automatically (Recommended)" and
click the "Next" button.
The "Hardware Installation" dialog box will appear. Click the
"Continue Anyway" button.
2
When installation of the driver is completed, click the "Finish"
button to finish the scanner driver installation.
3
Begin installation of the printer driver.
12
"SHARP AL-xxxx" (where xxxx is the model name of your MFP)
1
will appear in the "Found New Hardware Wizard" dialog box.
Select "Install the software automatically (Recommended)" and
click the "Next" button.
4
The "Hardware Installation" dialog box will appear. Click the
2
"Continue Anyway" button.
When installation of the driver is completed, click the "Finish"
button to finish the printer driver installation.
3
You have completed the installation of all the software.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing onto Windows 98/Me/2000 (USB interface)
Before starting the installation, make sure the USB interface cable is not connected
to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Double-click "My Computer" ( ), and then double-click the
CD-ROM ( ) icon.
2
When any of "Hardware Found", or "Found New Hardware Wizard"
messages appear during the software installation, be sure to click the
"Cancel" button.
Double-click the "setup" ( ) icon.
3
If the language selection screen appears after you double click the
"setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
Select the software packages to be
installed, and then click the "Next"
button.
4
The software packages with checkmark (
)
on the list on the screen will be installed. Click
the "Display README" button to show the
information on the selected package.
If the following screen appears, click the "OK" button. Review the
appropriate driver software packages to be installed.
Review the software packages to be installed on the screen,
and then click the "Start" button.
5
The software packages to be installed will be displayed on the screen. If
inappropriate packages are displayed, click the "Back" button to select
appropriate packages again.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying files for MFP driver installation.
6
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the interface cable
is not connected to the MFP. Make sure that the interface cable is
not connected and click the "Next" button.
2
Click the "Next" button in the dialog box
3
showing the files to be copied for installation
of the MFP driver.
The setup program will start to copy the files.
In Windows 2000, if the following screen appears
while the files are being copied (the message
may appear more than once), click "Yes" in
Windows 2000.
The following screen appears when all of
4
the files for the USB interface connection
have been copied. If you are not using a
parallel interface cable for connection to the
MFP, please click the "No" button.
4
When the "The MFP driver installation is complete." dialog box
5
appears, click the "OK" button.
The Button Manager installer will start.
Begin installation of the Button Manager (This step will start if it
was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
Read the message in the "Please read the following information."
window, and then click the "Next" button.
2
When a message appears that lets you specify the location for the
software to be installed, click the "Next" button.
3
If the program displays "Do you want the Button Manager added to
Windows Startup?", check "Yes" and click the "OK" button.
4
The setup program will start to copy the files.
Click the "Finish" button when the message to inform you of the
completion of the installation appears.
5
The Sharpdesk installer will start.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Sharpdesk (This step will start if it was
selected in step 4).
8
After confirming the message in the "Welcome to Sharpdesk
installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
The setup program will start to copy the files.
If the dialog box asking "This program is
about to install Sharpdesk imaging, which
does not support LZW compression."
appears, answer the question to continue the
Sharpdesk installation.
Click the "Finish" button when the message
to inform you of the completion of the installation appears.
5
Click the "Close" button when the
message to inform you of the
completion of the installation appears.
When the "Now connect the MFP
interface cable to the PC." dialog box
or "After Windows system restarts..."
dialog box appears, click the "OK"
button.
9
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
Make sure that the power of the MFP is turned on, and then
connect the USB interface cable. (p.45)
Windows will detect the MFP and the Plug and Play screen will appear.
10
11
Follow the instructions in the Plug and Play screen that
appears in your version of Windows to begin the installation.
You have completed the installation of the software.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing onto Windows 95/98/Me/NT4.0/2000
(Parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not
connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Double-click "My Computer" ( ), and then double-click the
CD-ROM ( ) icon.
2
When any of "Hardware Found", or "Found New Hardware Wizard"
messages appear during the software installation, be sure to click the
"Cancel" button.
Double-click the "setup" ( ) icon.
3
If the language selection screen appears after you double click the
"setup" icon, select the language you wish to use and click the "Next"
button. (Normally, the correct language is selected automatically.)
4
Select the software packages to be
installed, and then click the "Next"
button.
4
The software packages with checkmark (
on the list on the screen will be installed.
)
Click the "Display README" button to show
the information on the selected package.
In Windows 95/NT 4.0, "Button
Manager" does not appear. In
Windows 98/Me/2000, do not select
the "Button Manager" checkbox.
because this is not supported when
using the parallel interface.
The next screen appears. Make sure that the parallel interface
cable is not connected, and click "OK".
5
6
Windows 95/NT 4.0
Windows 98/Me/2000
Check the contents of the package on the screen, and then
click the "Start" button.
The software packages to be installed will be displayed on the screen. If
inappropriate packages are displayed, click the "Back" button to select only
appropriate software packages.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying files for MFP driver installation and parallel interface
setup (This step will start if it was selected in step 4).
7
After confirming the message in the "Welcome" window, click the
"Next" button.
1
A dialog box appears asking you to verify that the USB or parallel
interface cable is not connected to the MFP. Make sure that the
interface cable is not connected and click the "Next" button.
2
Click the "Next" button in the dialog box to
3
install the MFP driver or Cancel to quit the
installation.
The setup program will start to copy the files.
In Windows 2000, if the following screen appears
while the files are being copied (the message
may appear more than once), click "Yes" in
Windows 2000.
The following screen appears. Click the "Yes" button, and then the
Model screen will appear. Select the model number that is the
same as the model name of your MFP and click the "Next" button.
4
Be sure to select the displayed model number that is the same as the
MFP's model name. If they are not the same, the driver will not be
installed correctly.
Establish the printer settings and click the
"Next" button.
5
Select "LPT1" for the port to be used. If "LPT1"
does not appear, it is likely that another printer or
peripheral device is using "LPT1". Check your
other printers and peripheral devices, and change
the port setting as needed so no device is using
"LPT1". If you wish the MFP to be your default
printer, select "Yes". If not, select "No".
When the "Setup has completed gathering all necessary installation
information" dialog box appears, click the "Yes" button.
6
The parallel interface driver is installed.
When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
7
The Sharpdesk installer will start.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Sharpdesk (This step will start if it was
selected in step 4).
8
After confirming the message in the "Welcome to Sharpdesk
installation" window, click the "Next" button.
1
Read the message in the "Information" window, and then click the
"Next" button.
2
When the "Choose Destination Location" window appears, click
the "Next" button.
3
When the "Select Program Folder" window appears, click the
"Next" button.
4
The setup program will start to copy the files.
If the dialog box asking "This program is
about to install Sharpdesk imaging, which
does not support LZW compression."
appears, answer the question to continue
the Sharpdesk installation.
Click the "Finish" button when the
message to inform you of the completion of the installation
appears.
5
4
Click the "Close" button when the
message to inform you of the
completion of the installation appears.
When the "Now connect the MFP
interface cable to the PC." dialog box
or "After Windows system restarts..."
dialog box appears, click the "OK"
button.
9
After the installation, a message to
restart your computer may be
displayed. In this case, click the "Yes"
button to restart your computer.
Make sure that the power of the MFP is turned on, and then
10
You have completed the installation of all the software.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICATORS ON THE OPERATION PANEL
The ONLINE indicator and the start (
scanner.
) indicator indicate the state of the printer or
SCANNER indicator
ONLINE indicator
Start indicator
Power save indicator
Start indicator
On:
Indicates the unit is ready for copying or scanning is being performed.
Blinking: The indicator blinks in the following situations:
• When a print job is interrupted.
• When reserving a copy job.
• When toner is being replenished during a copy or print job.
Off:
The indicator is off in the following situations:
• During copying or scanning.
• The unit is in the auto power shut-off mode.
• When a misfeed or error has occurred.
ONLINE indicator
The ONLINE key is pressed and on line and off line are changed.
On:
Indicates the unit is ready for printing or scanning is being performed.
(On line)
Blinking: Printing or data is being received from a computer.
Off:
Copying is being performed. (Off line)
Power save indicator
On:
Indicates the unit is in a power save mode.
Blinking: Indicates that the unit is initialising (when the side cover is opened and
closed or the power turned off and on).
SCANNER indicator
On:
The SCANNER (
) key has been pressed and the unit is in scanner
mode.
Blinking: A scan job is being executed from the computer, or scan data is stored
in the unit's memory.
Off:
The unit is in the copy mode.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PRINTER MODE
For problems with the printer function, see the online manual or the help
file for the driver.
Opening the printer driver from the start menu
Open the printer driver setup screen by either of the methods shown below.
Click the "start" button.
1
Click "Control Panel", select "Printers and Other Hardware",
and then click " Printers and Faxes.
2
On Windows 95/98/Me/NT4.0/2000, select "Settings" and click "Printers".
Click the "SHARP AL-xxxx" (where xxxx is the model name of
your unit) printer driver icon in the "Printers" window and from
the "File" menu select "Properties".
3
On windows NT 4.0, select "Document Defaults" to open the
printer driver setup screen.
4
Click "Printing Preferences" button in the "General" tab.
On Windows 95/98/Me, click the "Setup" tab.
The printer driver setup screen will appear.
4
Refer to the Windows manual or help file for more information on
the "General" tab, "Details" tab, "Color Management" tab and
"Sharing" tab.
How to print
Make sure that the paper of the desired size and type is loaded
in the tray.
1
The procedure for loading paper is the same as for loading copy paper. See
"LOADING PAPER" (p.14).
Open the document you intend to print, and select "Print" from
the application's "File" menu.
2
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure that "SHARP AL-xxxx" (where xxxx is the model
name of your unit) is selected as the current printer. If you
intend to change any print setting, click the "Preferences"
button to open the setting dialog.
On Windows 95/98/Me/NT 4.0, click the "Properties" button.
On Windows 2000, the "Properties" button does not appear. Set your
preferences by switching the tab in the "Print" dialog box.
3
4
Specify the print settings including the number of copies,
media type, and print quality, and then click the "Print" button
to start printing.
On Windows 95/98/Me/NT 4.0, click the "OK" button to start printing.
For details on print settings, see the online manual or the help file for the
printer driver.
• If copying is being performed when printing is started, copying will
continue. After copying is complete, printing will be executed when the
clear (
) key is pressed twice, the ONLINE key is pressed to switch
the unit to the online state or approximately 60 seconds (auto clear
time)* elapse.
• Preheat mode and auto power shut-off mode will be cancelled when
printing is started.
• If the paper size specified from the software application is larger than
the paper size in the printer, part of the image that is not transferred to
the paper may remain on the surface of the drum. In this case, the
backside of the paper may become dirty. If this occurs, change to the
correct size paper and print two or three pages to clean the image.
• If you start a print job while a scan job or copy job is in progress, the
print data will be stored in the unit's memory. When the scan job or
copy job is completed, printing will begin.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCANNER MODE
The scanner driver for this unit includes an STI (Still image) driver and WIA
(Windows Image Acquisition) driver. You can install software that supports the STI
driver and WIA driver to enable scanning using the operation panel of the unit.
For problems with the scanner function, see the online manual or the
help file for the driver.
Using the Button Manager
Setting up the Button Manager
The Button Manager accessory software supports the STI driver and WIA driver. Setup
that is required in Windows to use the Button Manager is explained in the following.
Windows XP
Click the "start" button, select "Control Panel" and click
1
"Printers and Other Hardware", and then click "Scanners and
Cameras" in the start menu. Right click the "SHARP AL-xxxx"
(where xxxx is the model name of your unit) icon and click
"Properties" in the menu that appears.
4
In the "Properties" screen, click the
"Events" tab.
2
Click the "Select an event" button and
3
select "ScanMenu SC1" from the pull-down
menu. Select "Button Manager (SHARP
Personal MFP series)" in "Start this
program" and click "Apply".
Repeat Step3 to set "ScanMenu SC2" through "ScanMenu SC6".
4
Click the "Select an event" button and select "ScanMenu SC2" from the pull-
down menu. Select "Button Manager (SHARP Personal MFP series)" in
"Start this program" and click "Apply". Do the same for each ScanMenu
through "ScanMenu SC6".
When the settings have been completed, click the "OK" button to close the
screen. When the settings have been completed in Windows, start the
Button Manager. Adjust detailed settings and then scan an image from the
unit. For the procedures for starting Button Manager and adjusting settings,
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 98/Me/2000
To scan directly into an application using the Button Manager on Windows 98,
Windows Me and Windows 2000. Set the Event Manager properties to send only to
Button Manager as shown below.
Click the "Start" button, select "Control Panel" from "Settings",
and open "Scanners and Cameras" in start menu.
1
In Windows Me, it occasionally happens that the "Scanners and
Cameras" icon does not appear immediately after installation of the MFP
driver is completed. If the icon does not appear, click "View all Control
Panel options" in the Control Panel and display the "Scanner and
Cameras" icon.
Select "AL-xxxx" (where "xxxx" is the model name of your
unit), and click the "Properties" button.
2
In Windows Me, right click "AL-xxxx" (where "xxxx" is model name of your
unit) and click "Properties" in the menu that appears.
In the "Properties" screen, click the
"Events" tab.
3
Click the "Scanner events" button and
4
select "ScanMenu SC1" from the pull-down
menu. Select "Button Manager (SHARP
Personal MFP series)" in "Send to this
application" and click "Apply".
If other application are shown,
deselect the checkboxes for the other
applications and leave only the Button
Manager checkbox selected.
Repeat Step4 to set "ScanMenu SC2" through "ScanMenu
SC6".
5
Click the "Scanner events" and select "ScanMenu SC2" from the pull-down
menu. Select "Button Manager (SHARP Personal MFP series)" in "Start this
program" and click "Apply". Do the same for each ScanMenu through
"ScanMenu SC6".
When the settings have been completed, click the "OK" button to close the
screen. When the settings have been completed in Windows, start the
Button Manager. Adjust detailed settings and then scan an image from the
unit. For the procedures for starting Button Manager and adjusting settings,
see "Scan Parameter Settings Dialog Box" (Next page).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Parameter Settings Dialog Box
After you have completed the Button Manager settings in
Windows, configure the scan settings in Button Manager.
To configure the scan settings in Button Manager, right click
the (
) icon in the Taskbar and select "Setting" from the
menu that appears.
For details on configuring the scan settings in Button
Manager, see the online manual or the help file.
This is the corresponding setting in the Button
Manager to automatically send multiple images
from the SPF in full colour at 75 dpi to
Sharpdesk using the operation panel "SC1"
SCANNER (
) key selection.
4
This dialog shows the SC1 event set to go directly to Button Manager.
With the Button Manager set to send the image to Sharpdesk. (factory
default setting) Sharpdesk will open after acquiring the image
automatically.
Flow of the Button Manager setting
The Button Manager can directly handle a AL-xxxx (where xxxx is the model name of
your unit) series device event and start your selected application according to the
scan setting made on the AL-xxxx (where xxxx is the model name of your unit) front
panel (SC1, SC2, SC3, SC4, SC5, SC6).
This will scan directly into your application from the device.
Scanner AL-
xxxx (where
xxxx is the
Event
Manager
Button
Manager
User
selected
application
model name
of your unit)
SCANNER
key pressed.
Windows OS
No Selection
dialog is
displayed.
The user
application
opens.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The settings for the Windows Event Manager for
the SHARP AL-xxxx (where xxxx is the model
name of your unit) device allow the user to take
advantage of the Sharp Button Manager to take
control of events from Windows and send
scanned images to any application that can be
selected in Button Manager.
This can be done with the Windows OS showing
the Event Manager selection dialog or directly
into a selected application if the Button Manager
is the only allowed handler for device events
from the SHARP AL-xxxx (where xxxx is the
model name of your unit).
This is done by changing the Windows device
settings for the AL-xxxx (where xxxx is the model
name of your unit) in the Scanner and Camera
device settings in the Control Panel.
This is the Control Panel
Properties dialog for "Scanners and
Cameras".
All About The Windows Event Manager and scanner events in
Windows 98, Windows Me, Windows 2000 and Windows XP.
Windows Platforms provide a mechanism for software to handle external events for
a scanner device like the SHARP AL-xxxx (where xxxx is the model name of your
unit) series products. This mechanism is controlled by the device manager on a
device basis. Applications that can handle events from a scanner/camera device
register with the Windows Event Manager and shown as available in the registered
applications. The path an event takes to get to the user's selected application
depends upon the event settings for the device.
Scanner AL-
xxxx (where
xxxx is the
model name
of your unit)
SCANNER
key pressed.
Event
Manager
Event
User selects
an
application.
Manager
selection
dialog
Windows OS
The user
application
opens.
Displayed on
screen
This is the Windows Event Manager
Selection Dialog.
Shown are two applications registered
to handle the scanner event from the
AL-xxxx (where xxxx is the model name
of your unit) device.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SCANNER key to begin scanning
• Scanning is not possible during a copy job.
•
If the SCANNER (
be stored.
) key is pressed during a print job, the scan job will
•
When scanning an original that has been placed in the SPF/RSPF, only one
original can be placed unless you are using Sharpdesk.
Press the SCANNER (
) key.
1
The unit enters scan mode.
Place the original you wish to scan on the original table/SPF/
RSPF.
2
3
For the procedure for placing the original, see "ORIGINAL PLACEMENT"
4
Press the right copy quantity key to
display the number of the application that
you wish to use for scanning.
The application numbers are initially as follows.
Application
Application launched
number
SC1
SC2
Sharpdesk (Full colour) (if installed)
Sharpdesk (Monochrome) (if installed)
E-mail (your standard e-mail program in the
Windows OS you are using)
SC3
SC4
SC5
SC6
Fax (if a fax program is installed)
OCR (if an OCR program is installed)
Microsoft Word (if installed)
then open the settings window of the Button Manager.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the start (
Scanning will start and the scanned data will be transferred to the
application.
) key.
4
• If the following screen appears, select
Button Manager and click "OK". Button
Manager starts and the application
associated with Button Manager starts. If
you want only Button Manager to start in
this case, set up Button Manager for use in
Windows as explained in "Setting up the
• If step 4 is performed with the "Show
TWAIN setting screen when scanning"
checkbox selected in the Scan Parameter Setting Dialog Box (p.37),
settings, and then press the start (
) key again or click the "Scan"
button in the TWAIN setting screen to start scanning. The scanned
data will be transferred to the application.
Opening the scanner driver and scanning from your computer
Follow the steps below to open the scanner driver setup screen. As an example, this
instruction is given using Sharpdesk as an image capture application.
• Scanning is not possible during a copy and print job.
• The method for starting the scanner driver differs depending on the
type of application. Refer to the manual or the help file of your
application.
• When using the scanner driver to scan an original that has been
placed in the SPF/RSPF. If you perform a pre-scan (see the online
manual or the help file for the scanner driver), the original in the SPF/
RSPF will be output to the exit area after scanning. To scan the
original after the pre-scan, place the original in the SPF/RSPF once
again.
Using the SHARP TWAIN
Place the original(s) you wish to scan on the original table/SPF/
RSPF.
1
For the procedure for placing the original, see "ORIGINAL PLACEMENT"
After starting Sharpdesk, click the
"File" menu and select "Select
Scanner".
2
Click here
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Select "SHARP Personal MFP
series", and click the "Select"
button.
3
4
Click here
If you use more than one scanning device, select the scanner
you want to use through the application. The method for
accessing the "Select Scanner" option, depends upon the
application. For more information, see the online manual or the
help file of your application.
Select "Acquire Image" from
the "File" menu, or click the
"Acquire" button ( ) .
4
Set the configuration for scanning (refer to the online manual
and help file), and click the "Scan" button.
Scan is started.
5
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning with the "Scanner and Camera Wizard" in Windows XP
Windows XP includes as a standard feature an image scanning function. The
procedure for scanning with the "Scanner and Camera Wizard" is explained here.
To cancel scanning, click the "Cancel" button in the screen that is
displayed.
Place the original you wish to scan on the original table/SPF/RSPF.
For the procedure for placing the original, see "ORIGINAL PLACEMENT"
1
Click the "start" button , select
2
"Control Panel", and click "Printers
and Other Hardware", and then click
"Scanners and Cameras" in the start
menu. Click the "SHARP AL-xxxx"
(where xxxx is the model name of your
unit) icon and click "Get picture" in
"Imaging Tasks".
The "Scanner and Camera Wizard"
appears. Click "Next" and establish the
basic settings for scanning.
3
For information on the settings, see the
Windows XP help file. After completing each
setting, click "Next".
Select a name, format, and folder for the
scanned image.
4
For information on the image name, file format,
and folder, see the Windows XP help file.
Scanning begins. When scanning ends,
select the next task you wish to perform.
5
For information on each selection, see the
Windows XP help file. To quit the "Scanner and
Camera Wizard", select "Nothing. I’m finished
working with these pictures." and click "Next".
Click "Finish" in the screen that appears.
The "Scanner and Camera Wizard" closes and the scanned image is saved.
6
42
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the unit as the printer
or scanner and a list of methods for dealing with printing or scanner problems.
To access the online manual, your computer must have Acrobat Reader 5.0 or a
later version. If it is not installed, refer to "Installing Acrobat Reader" (below).
Turn on your computer.
1
Insert the supplied CD-ROM into your CD-ROM drive.
2
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
3
On Windows 95/98/Me/NT 4.0/2000, double-click "My Computer" ( ), and
then double-click the CD-ROM ( ) icon.
Double-click the "Manual" folder,
4
double-click "English" and then
AL-1552_1553_1555 SERIES
double-click the
"AL_1552_1553_1555.pdf" icon.
The following window will appear.
4
Click the
to read the online manual.
5
To close the online manual, click the ( ) button located at the top-right of
the window.
• The online manual can be printed out using Acrobat Reader. SHARP
recommends printing out the sections which you refer to regularly.
• Refer to "Help" of Acrobat Reader for more details on the operation
and function of Acrobat Reader.
Installing Acrobat Reader
Turn on your computer.
1
Insert the CD-ROM into the CD-ROM drive.
2
Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
3
Windows95/98/Me/NT4.0/2000, double-click "My Computer" ( ), and then
double-click the CD-ROM ( ) icon.
Double-click the "Acrobat" folder, and then double-click the
"ar500enu.exe" icon.
4
Follow the on-screen instructions to install Acrobat Reader.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
USING OTHER INSTALLED DRIVERS
If you use another GDI printer or a Windows Printing System printer, interference
between printers may occur and printing may not be performed properly. To use
another GDI printer or a Windows Printing System printer, you must change the port
setting of the printer driver using the following procedure.
If another printer does not operate properly when the SHARP Personal
MFP series printer driver is set to "FILE" as described below, uninstall
the SHARP Personal MFP series printer driver. To uninstall the printer
driver, see the online manual.
Click the "start" button.
1
Click "Control Panel", click "Printer and Other Hardware" and
then click "Printer and Faxes".
2
On Windows 95/98/Me/NT4.0/2000, select "Settings" and then click
"Printers".
Right-click the "SHARP AL-xxxx" (where
3
xxxx is the model name of your unit) icon in
the printer dialog box and then click
"Properties".
Click the "Ports" tab ("Details" tab - on Windows 95/98/Me) in
the "Properties" dialog box, select "FILE:" in the "Print to the
following port" list box, and click the "OK".
4
Right-click the icon of the printer to be used and click
"Properties".
5
Click the "Ports" tab ("Details" tab - on Windows 95/98/Me) in
the "Properties" window, select "LPT1" (or the currently used
port), and click the "OK" button.
6
To use the SHARP Personal MFP series again, perform the same
procedure but select the port to be used (for example, LPT1) in step 4.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE INTERFACE CABLE
This unit includes both USB and parallel interface connectors.
Interface cables for connecting the unit to your computer are not included with this
unit. Please purchase the appropriate cable for your computer.
I
•
If you intend to use the unit as a scanner, it must be connected to
your computer with a USB interface cable. The scanner function
cannot be used if the unit is connected with a parallel cable.
• USB is available with a PC/AT compatible computer that was originally
equipped with USB and had Windows 98, Windows Me, Windows
2000 Professional, Windows XP Professional or Windows XP Home
Edition preinstalled.
• Do not connect the interface cable before installing the MFP driver.
The interface cable should be connected during installation of the
MFP driver. (p.22)
Connecting the USB interface cable
Obtain a shielded USB interface cable.
1
4
Insert the cable into the USB interface
connector located on the rear of the
unit.
2
Insert the other end of the cable into the interface connector of
your computer, or the USB hub connected to your computer.
3
Connecting the parallel interface cable
Obtain an IEEE1284 shielded parallel interface cable.
1
Ensure that your computer and unit are turned off.
2
Insert the cable into the parallel
3
interface connector located on the
rear of the unit, and fasten with
clasps.
Insert the other end of the cable into the interface connector of
your computer.
4
45
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING COPIES
This chapter explains basic and other copying functions.
The unit is equipped with a one-page memory buffer. This memory allows the unit to
scan an original once only and make up to 99 copies. This feature improves
workflow, reduces operation noise from the copier, and provides higher reliability by
reducing wear and tear on the scanning mechanism.
5
If the unit does not function properly during use, or if a function cannot
COPY FLOW
1 Make sure that paper has been loaded in the paper tray (p.15)
or multi-bypass tray (p.17), and check the paper size (p.14).
If paper is not loaded, see page 15. If you are using the single bypass, check
the paper size and then proceed to the next step without loading paper.
2 Place the original.
If you are using the original table, see "Using the original table" (p.47).
If you are using the SPF, see "Using the SPF/RSPF" (p.48).
When copying onto paper larger than A4, pull out the paper output tray
extension.
3 Select the copy settings.
If you wish to copy using the initial settings (p.13), proceed to the next step.
To set the number of copies, see page 49.
To adjust the resolution and contrast settings, see page 49.
To enlarge or reduce the copy, see page 51.
To change the tray used, see page 51. (AL-1553, AL-1555)
To print on both sides of the paper, see page 52.
4 Start copying.
If you are using the single bypass
Press the start (
) key.
Do not press the start (
sheet of paper into the single bypass.
(Page 18)
) key. Insert a
Multiple copies are not possible
using the single bypass.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not insert paper in the single bypass when a copy job from the paper
tray is in progress. This will cause a misfeed.
• If you start a print job while a copy job is in progress, the print job will
begin when the copy job is completed.
• The scanning function cannot be used while a copy job is in progress.
About interrupt copying
If you press the start ( ) key to begin a copy job while a print job using the paper
tray or multi-bypass tray is in progress, the copy job will begin automatically after the
print data in the unit's memory is printed (interrupt copying). When this is done, the
print data remaining in the computer is not sent to the unit. When the copy job ends,
press the clear (
) key twice, or press the ON LINE key once to change the unit to
remaining print data will be sent to the unit and printing will resume. Interrupt copying
is not possible during a print job using the single bypass.
ORIGINAL PLACEMENT
Using the original table
• The original table can read up to A4 original.
5
• Image loss 4mm can occur at the leading and trailing edges of the
copies. Also image loss 4.5mm in total can occur along the other
edges of the copies. It can be 6 mm (max.) at the trailing edge of the
second copy of two-sided copying.
• When copying a book or an original which has been folded or a
crumpled original, press down the original cover lightly. If the original
cover is not securely closed, the copies may be striped or blurred.
• The original cover can be simply lifted straight up and reattached to
allow copying of a large original (AL-1552)
Open the original cover/SPF/RSPF, and place the original.
1
Place an original face down on the original table. Align it with
the original scale and the centring ( ) mark. Gently close the
original cover/SPF/RSPF.
2
Original scale
mark
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a large original (AL-1552)
The original cover can be removed to allow copying of bulky objects.
Simply lift the original cover straight
up.
1
To reattach the original cover, reverse the above procedure.
2
Using the SPF/RSPF
The SPF is designed to hold up to 30 originals measuring from A5 to A4 and
2
2
weighting from 52g/m to 90g/m .
• Before feeding originals in the original feeder tray, be sure to remove
any staples or paper clips from them.
• Before placing curled or wavy originals into the original feeder tray, be
sure to flatten them. If not, original misfeeds may result.
• The SPF/RSPF (
) indicator on the operation panel will light up. If
this indicator does not light up, the originals are not properly set or the
SPF/RSPF is not properly closed.
• Badly damaged originals may misfeed in the SPF/RSPF. It is
recommended that such originals be copied from the original table.
• Special originals such as transparency film should not be fed through
the SPF/RSPF, but should be placed directly on the original table.
• Image loss (max. 4 mm) can occur at the leading and trailing edges of
the copies. Also image loss (max. 4.5 mm in total) can occur along the
other edges of the copies. It can be 6 mm (max.) at the trailing edge of
the second copy of two-sided copying.
• To stop continuous copying using the SPF/RSPF, press the clear
(
) key.
• Copying using one-sided to one-sided mode (AL-1555) :
Ensure that no indicator is lit among the original to copy indicators.
Make sure that no original is left on the original table.
1
2
Adjust the original guides to the size
of originals.
Set the originals face up in the
Original face up
3
original feeder tray.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Stream feeding mode
The stream feeding mode allows easy operation of continuous copying from the SPF/
RSPF. If the stream feeding mode has been enabled using user program No.4, the
SPF/RSPF (
) indicator will blink approximately 5 seconds after the last original has
been fed by the SPF/RSPF. While this indicator is blinking, any new originals placed in
the original feeder tray will be fed and copied automatically. If the stream feeding
mode has been disabled, the start (
) key must be pressed each time the originals
are set even immediately after completion of a copy run from the SPF/RSPF. The
SET THE COPY QUANTITY
Set the number of copies using the two copy quantity (
from the original table or copying from SPF/RSPF.
,
) keys when copying
• Press the clear (
) key to clear an entry if a mistake is made.
• A single copy can be made with the initial setting, i.e., when "0" is
displayed.
• Press the right copy quantity key to set the unit digit
from 0 to 9. This key will not change the tens digit.
• Press the left copy quantity key to set the tens digit
from 1 to 9.
Tens digit Unit digit
5
EXPOSURE ADJUSTMENT/PHOTO COPYING
Exposure adjustment
Copy density adjustment is not required for most originals in the automatic exposure
mode. To adjust the copy density manually or to copy photographs, the exposure
level can be adjusted in two steps manually.
The copy resolution used for AUTO and MANUAL (
changed. (p.55)
) mode can be
Press the exposure mode selector key to
1
2
select the MANUAL (
) mode or
PHOTO (
) mode.
Use the light (
) and dark (
) keys to
adjust the exposure level. If exposure level
2 is selected, the two left-handmost
indicators for that level will light up
simultaneously. Also, if level 4 is selected,
the two right-handmost indicators for that
level will light up simultaneously.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic exposure adjustment
This automatic exposure level will remain in effect until you change it
again by this procedure.
The automatic exposure level can be adjusted to suit your copying needs. This level is
set for copying from the original table and copying from the SPF/RSPF respectively.
When adjusting the automatic exposure level for copying from
1
the SPF/RSPF, place an original in the original feeder tray and
make sure that the SPF/RSPF (
) indicator lights up. When
adjusting the level for copying from the original table, make
sure that no original is left in the original feeder tray.
Press the exposure mode selector key to
2
3
select the PHOTO (
) mode.
Press and hold down the exposure mode
selector key for approximately 5 seconds.
The PHOTO (
) indicator will go out and
the AUTO indicator will begin to blink. One
or two light and dark indicators
corresponding to the automatic exposure
level which has been selected will light up.
Press the light (
) or dark (
) key to
4
5
lighten or darken the automatic exposure
level as desired. If exposure level 2 is
selected, the two left-handmost indicators
for that level will light up simultaneously.
Also, if level 4 is selected, the two right-
handmost indicators for that level will
light up simultaneously.
Press the exposure selector key. The AUTO indicator will stop
blinking and light up steadily.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
REDUCTION/ENLARGEMENT/ZOOM
Three preset reduction ratios and two enlargement ratios can be selected. The zoom
function enables copy ratio selection from 25% to 400% in 1% increments.
Set the original and check the paper size.
1
Use the copy ratio selector key and/or ZOOM (
select the desired copy ratio.
,
) keys to
2
• To verify a zoom setting without changing the zoom ratio,
press and hold down the copy ratio display (%) key. When the
key is released, the display will return to the copy quantity
display.
• To reset the ratio to 100%, press the copy ratio selector key
repeatedly until the 100% indicator lights up.
Set the reduction/enlargement ratio.
3
To decrease or increase the zoom ratio rapidly, press and hold
down the ZOOM (
) or (
) key. However the value will
stop at the preset reduction or enlargement ratios. To move
beyond these ratios, release the key and then press and hold it
down again.
5
To select a preset copy ratio:
Preset reduction and enlargement ratios are:
A5
A4
141
25%, 70%, 86%, 141%, and 400%.
A4 B5
86
70
A4
A5
To select a zoom ratio:
When a ZOOM (
or
) key is pressed, the
A4
ZOOM indicator will light up and the zoom ratio will
be displayed in the display.
B5
A5
A4
SELECTING THE TRAY (AL-1553, AL-1555)
Press the tray select (
Each time you press the tray select (
indicated by the paper feed location indicator changes in
the following order: paper tray, multi-bypass tray.
) key.
AL-1555
) key, the location
A5
A4
141
A4 B5
A4 A5
86
70
51
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FUNCTIONS
This chapter describes the special functions of this unit. Use these functions as
needed.
6
TWO SIDED COPYING
When copying from the SPF/RSPF, two-side originals can be copied automatically
without having to manually turn them over. Automatic two-sided copying can also be
performed without using the SPF/RSPF. When copying from one-sided originals to
two-sided copies, copying orientation can be selected between Turn on Long Edge
and Turn on Short Edge.
• When making two-sided copies from the original table, the paper size
must be A4, letter. When making two-sided copies from the SPF/
RSPF, A4, B5, A5, letter, legal, and invoice sizes can be used. Non-
standard size paper cannot be used.
• When making two-sided copies, the multi-bypass tray cannot be used.
• When using two-sided invoice size originals from the SPF/RSPF, be
sure to place them in the landscape orientation. Otherwise, an original
misfeed will occur.
A
A
A
A
A A
A A
Turn on Long Edge
Making two-sided copies
Turn on Short Edge
Place the original on the original table or in the SPF/RSPF. (see
1
2
Select two-sided copy mode.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
A: When copying in a one-sided to two-sided mode:
Use the original to copy key to select the desired one-sided to two-sided
copying mode (Turn on Long Edge or Turn on Short Edge). See the
B: When copying in the two-sided to two-sided mode:
Use the original to copy key to select the two-sided to two-sided copying
mode. The originals must be set in the SPF/RSPF before this mode can
C: When copying in the two-sided to one-sided mode:
Use the original to copy key to select the two-sided to one-sided copying
mode. The originals must have been set in the SPF/RSPF in step 3 on
page 48 (AL-1555).
AL-1555
A
A
B
C
AL-1552_AL-1553
Select the copy settings. See "SET THE COPY QUANTITY"
3
6
Using the original table
If you are using the original table, copying is only possible in one sided to
two-sided mode ("A" above).
Press the start ( ) key.
1
The original is scanned into the unit's memory.
Place the original that you wish to copy onto the rear side of the
paper, and press the start ( ) key again.
2
Copying begins.
Using the SPF/RSPF
Press the start ( ) key. Copying begins in the selected two-sided copy mode.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (page 54)
Reduces toner consumption by approximately 10%.
The unit has two power save modes of operation: preheat mode and auto power
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save ( ) indicator will light up
and other indicators will remain on or off as before. In this condition, the fuser in
the unit is maintained at a lower heat level, thereby saving power. To copy from
the preheat mode, make desired copier selections and press the start ( ) key
using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save ( ) indicator
will light up and other indicators will go out. The auto power shut-off mode saves
more power than the preheat mode but requires a longer time before starting
copying. To copy from the auto power shut-off mode, press the start ( ) key.
Then make desired copier selections and press the start ( ) key using the
normal copying procedure.
The unit returns to the initial settings a preset amount of time after the end of copy, or
scanner operation. This preset amount of time (auto clear time) can be changed.
Stream feeding mode (page 55)
For description of the stream feeding mode, see "Stream feeding mode" (p.49).
Resolution of AUTO & MANUAL mode (page 55)
You can set the copy resolution used for AUTO and MANUAL (
mode.
) exposure
TONER SAVE MODE
Press the exposure mode selector key
1
to select the manual (
) mode.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Press and hold down the exposure mode
selector key for approximately 5 seconds.
2
3
The MANUAL (
) indicator will go out
) indicator will begin
and the PHOTO (
to blink. The light and dark indicator
marked "5" will light up, indicating the
standard toner mode is active.
To enter the toner save mode, press the
light (
) key. The light and dark
indicator marked "1" will light up,
indicating the toner save mode is
selected.
Press the exposure mode selector key. The PHOTO (
)
4
indicator will stop blinking and light up steadily. The light and
dark indicator marked "3" will light up. The toner save mode is
now active.
To return to the standard mode, repeat the procedure but use the dark
(
) key to select exposure level "5" in step 3.
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or
canceled as desired.
6
Setting the power save modes, auto clear time, stream
feeding mode and resolution of AUTO & MANUAL mode
Press and hold down the light (
) and dark (
) keys
1
simultaneously for more than 5 seconds until all the alarm
indicators (
,
,
) blink and "
" appears in the display.
Use the left copy quantity (
) key to select a user program
2
number (1: auto clear time, 2: preheat mode, 3: auto power
shut-off timer, 4: stream feeding mode, 5: auto power shut-off
mode 6: resolution of AUTO & MANUAL mode). The selected
number will blink in the left side of the display.
Press the start (
steadily lit and the currently selected parameter number for the
program will blink on the right side of the display.
) key. The entered program number will be
3
4
Select the desired parameter using the right copy quantity (
key. The entered parameter number will blink on the right of the
display.
)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Program
No.
Mode
Parameters
0
*3
OFF, 1
60sec., 4
10sec., 2
90sec., 5
30sec.
120sec.
1
2
3
Auto clear time
Preheat mode
*0
30sec., 1
60sec., 2
90sec.
Auto power shut- off
timer
0
3
2min., *1
30min. 4
5min., 2
60 min. 5
15min.
120min.
Stream feeding
mode
4
5
6
0
OFF, *1
OFF, *1
300dpi, 1
ON
Auto power shut- off
mode
0
ON
Resolution of AUTO
& MANUAL mode
*0
600dpi
* Factory default settings are indicated with an asterisk (*).
Program No. 4 can be selected on when your unit has the SPF/
RSPF.
Press the start (
) key. The right-hand number in the display
5
6
will be steadily lit and the entered value will be stored.
To change the setting or to set another mode, press the clear
(
) key. The unit will return to step 2.
Press the light (
copy mode.
) or dark (
) key to return to the normal
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press and hold down the clear (
) key for approximately 5 seconds.
The total number of copies will appear in two steps, each with three
digits.
Example: Total number of copies is 1,234.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
This chapter describes how to replace the TD cartridge and drum cartridge, and how
to clear the unit.
7
Be sure to use only genuine SHARP parts and supplies.
TD CARTRIDGE REPLACEMENT
The TD cartridge replacement required ( ) indicator will light up when toner is
needed. For more information on purchasing the TD cartridge, see "ABOUT
SUPPLIES AND OPTIONS" (p.70). If copying is continued while the indicator is lit,
copies will gradually become lighter until the unit stops and the indicator begins
blinking. Replace the old TD cartridge by following the procedure below.
• After the unit stops, it may be possible to make a few more copies by
taking the TD cartridge out of the unit, shaking it horizontally, then
reinstalling it. If copying is not possible after this operation, replace the
TD cartridge.
• During long copy run of a dark original, the start (
blink, the indicator light up, and the unit stop, even though toner is left.
The unit will feed toner up to 2 minutes and then the start (
indicator will light up. Press the start ( ) key to restart copying.
) indicator may
)
Open the multi-bypass tray (AL-1553, AL-1555), side cover,
1
2
and front cover, in that order.
Gently pull the TD cartridge out
Lock release button
7
while pressing the lock release
button.
Dispose of the old TD cartridge in accordance with local regulations.
Install a new TD cartridge. To install the new cartridge, see
3
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The indicator
4
(
) will go out and the start (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies. When the internal
counter reaches approximately 17,000 copies, the drum replacement required (
)
indicator will light up indicating that replacement of the drum cartridge will be needed
soon. For more information on purchasing the drum cartridge, see "ABOUT
SUPPLIES AND OPTIONS" (p.70). When the indicator begins to blink, the unit will
stop operating until the cartridge is replaced. Replace the drum cartridge at this time.
Do not remove the protective cover on the drum portion (black paper) of
a new drum cartridge before use. The cover protects the drum against
external light.
Remove the TD cartridge (see "TD CARTRIDGE
1
Hold the drum cartridge handle and
gently pull the cartridge out.
2
Drum cartridge handle
Dispose of the old TD cartridge in accordance with local regulations.
Remove the new drum cartridge from the protective bag and
remove the protective cover from the cartridge. Then gently
install the new drum cartridge.
3
Do not touch the surface of the drum (green portion) of the
cartridge. Doing so may cause smudges on the copies.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Gently install the TD cartridge. To install the TD cartridge, see
4
5
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The drum
replacement required (
) indicator will go out and the start
(
) indicator will light up.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
CLEANING THE UNIT
Proper care is essential in order to get clean, sharp copies. Be sure to take a few
minutes to regularly clean the unit.
• Before cleaning, be sure to turn the power switch off and remove the
power cord from the outlet.
• Do not use thinner, benzene or other volatile cleaning agents. Doing
so may cause deformation, discoloration, deterioration or malfunction.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and the back side of the original cover/SPF/RSPF
Stains on the glass, SPF/RSPF scanning window (AL-1553, AL-1555), cover or
SPF/RSPF roller will also be copied. Wipe the glass, SPF/RSPF scanning window,
cover and SPF/RSPF roller with a soft, clean cloth. If necessary, dampen the cloth
with a glass cleaner.
Original table/scanning window
Original cover/SPF/RSPF
7
SPF/RSPF roller
Scanning window
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer charger
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean
the charger using the following procedure.
Turn the power switch off. (p.13)
1
Ensure that the multi-bypass tray is open (AL-1553, AL-1555)
and then open the side cover while pressing the side cover
open button.
2
Take the charger cleaner out by holding the tab. Set the charger
3
cleaner onto the right end of the transfer charger, gently slide
the cleaner to the left end, and then remove it. Repeat this
operation two or three times.
Slide the charger cleaner from the right end to the left end along
the groove of the transfer charger. If the cleaner is stopped on
the way, smudges on copies may occur.
Return the charger cleaner
4
to its original position.
Close the side cover by
pressing the round
projections near the side
cover open button.
Turn the power switch on. (p.12)
5
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING THE UNIT
This chapter describes misfeed removal and troubleshooting.
For problems with the printer function or the scanner function, see the online manual
or the Help file for the printer/scanner driver.
8
TROUBLESHOOTING
If any problem occurs, check the list below before contacting your authorised service
representative.
Problem
Possible cause
Unit plugged in?
Power switch on?
Side cover closed securely? Gently close the side cover.
Front cover closed?
Solution
Plug the unit into a grounded outlet.
Turn the power switch on.
Page
Unit does not
operate.
Gently close the front cover and then
close the side cover.
Is the original placed face
Place the original face down on the
Blank copies
down on the original table or original table or face up in the SPF/
face up in the SPF/RSPF? RSPF.
Is original image too dark or Adjust the exposure manually.
too light?
Copies are too
Is the unit in the automatic Adjust the automatic exposure level.
dark or too light. exposure mode?
Is the unit in the photo
exposure mode?
Original table or original
cover dirty?
Cancel the photo exposure mode.
Clean regularly.
Dust, dirt,
smudges appear
Original smudged or
blotchy?
Use a clean original.
on copies.
–
Striped copies
Is transfer charger clean? Clean the transfer charger.
Non-standard paper used? Use standard paper. If using special
papers, feed the paper through the
single bypass/multi-bypass tray.
Paper curled or damp?
Store paper flat in the wrapper in a
dry location.
–
Paper misfeeds
frequently.
Pieces of paper inside unit? Remove all pieces of misfed paper.
Paper guides in the paper Set the guides properly depending on
tray not set properly?
Too much paper in the
the paper size.
Remove excessive paper from the
paper tray or multi-bypass tray.
tray?
8
Is the paper too heavy?
Paper damp?
Use paper within the specified range.
Replace with dry paper. If the unit is
not used for long time, remove the
paper from the paper tray and store it
in its wrapper in a dry location.
Images rub off the
copy easily.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
Indication
Cause and remedy
Page
Steadily Replacement of drum cartridge will be needed
lit
soon. Prepare a new cartridge.
Drum replacement
required indicator
Drum cartridge must be replaced. Replace it with
a new one.
Blinking
Steadily Replacement of TD cartridge will be needed
TD cartridge
lit
soon. Prepare a new cartridge.
replacement
TD cartridge must be replaced. Replace it with a
new one.
required indicator
Blinking
A misfeed has occurred. Remove the misfed
Misfeed indicator
An original misfeed has occurred in the SPF/
SPF/RSPF misfeed
indicator
RSPF. Remove the misfed originals referring to
Blinking
the description of "E: Misfeed in the SPF (AL-
The unit is in the preheat mode. Press any key to
cancel the preheat mode.
The unit is in the auto power shut-off mode.
Press the start ( ) key to cancel the auto power
shut-off mode.
Power save indicator is
steadily lit.
The paper tray indicator is
blinking.
The paper tray is not installed properly. Push the
tray into the unit securely.
–
The TD cartridge is not installed. Check if the
cartridge is installed. If "CH" is blinking even if a
cartridge is installed properly, contact your
authorised service representative.
"CH" is blinking in the display.
Side cover is open. Close the side cover securely
by pressing the round projections near the side
cover open button.
"CH" is steadily lit in the
display.
–
The paper tray or multi-bypass tray is empty.
Load paper.
A misfeed has occurred in the paper tray, single
bypass or multi-bypass tray. Remove the misfed
paper.
"P" is blinking in the display.
The scan head locking switch is locked. Unlock
the scan head locking switch and turn the power
switch off/on.
A letter and a number appear
alternately.
–
The unit will not function. Turn the power switch
A letter and a number appear off and then switch it on, and if there is again an
alternately.
error, remove the power cord from the outlet, and
contact your authorized service representative.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
MISFEED REMOVAL
When the misfeed ( ) indicator blinks or
blinks in the display, the unit will
stop because of a misfeed. If a misfeed occurs when using the SPF/RSPF, a number
may appear in the display after a minus sign. This indicates the number of the
originals that must be returned to the original feeder tray after a misfeed. Return the
required number of originals. Then this number will disappear when copying is
resumed or the clear (
original sheet, the unit will stop and the SPF/RSPF misfeed (
) key is pressed. When the SPF/RSPF misfeeds an
) indicator will blink,
while the misfeed ( ) indicator will remain off. For a misfeed of originals in the SPF/
Open the multi-bypass tray (AL-1553, AL-1555), and side
cover, in that order.
1
Check the misfeed location. Remove the misfed paper
2
following the instructions for each location in the illustration
If the misfed paper is seen from
this side, proceed to "C: Misfeed
in the transport area". (p.65)
If paper is misfed here, proceed to "B:
Misfeed in the fusing area". (p.64)
If paper is misfed here, proceed
to "D: Misfeed in the lower
paper feed area". (p.66)
If paper is misfed here, proceed to "A:
Misfeed in the paper feed area". (p.64)
8
63
Download from Www.Somanuals.com. All Manuals Search And Download.
A: Misfeed in the paper feed area
Gently remove the misfed paper from the paper feed area as
1
shown in the illustration. When the misfeed (
) indicator
blinks, and the misfed paper is not seen from the paper feed
area, pull out the paper tray and remove the misfed paper. If the
paper cannot be removed, proceed to "B: Misfeed in the fusing
area".
The fusing unit is hot. Do not touch the fusing unit when
removing misfed paper. Doing so may cause a burn or other
injury.
• Do not touch the surface of the drum (green portion) of the
drum cartridge when removing the misfed paper. Doing so
may damage the drum and cause smudges on copies.
• If the paper has been fed through the multi-bypass tray, do not
remove the misfed paper through the multi-bypass tray. Toner
on the paper may stain the paper transport area, resulting in
smudges on copies.
Close the side cover by pressing the round projections near
2
the side cover open button. The misfeed (
) indicator will go
out and the start (
) indicator will light up.
B: Misfeed in the fusing area
Lower the fusing unit release
lever.
1
Fusing unit release lever
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Gently remove the misfed paper
from under the fusing unit as shown
in the illustration. If the paper
2
cannot be removed, proceed to "C:
Misfeed in the transport area".
The fusing unit is hot. Do not
touch the fusing unit when
removing misfed paper. Doing
so may cause a burn or other
injury.
• Do not touch the surface of the drum (green portion) of the
drum cartridge when removing the misfed paper. Doing so
may cause smudges on copies.
• Do not remove the misfed paper from above the fusing unit.
Unfixed toner on the paper may stain the paper transport
area, resulting in smudges on copies.
Raise the fusing unit release lever and then close the side
cover by pressing the round projections near the side cover
3
open button. The misfeed (
) indicator will go out and the
start ( ) indicator will light up.
C: Misfeed in the transport area
Lower the fusing unit release lever.
1
Open the front cover.
2
3
To open the front cover, see "INSTALLING THE TD CARTRIDGE" (p.10).
Rotate the feeding roller in
the direction of the arrow
and gently remove the
Feeding roller
misfed paper from the exit
area.
8
4
5
Raise the fusing unit release lever, close the front cover and
then close the side cover by pressing the round projections
4
near the side cover open button. The misfeed (
) indicator
will go out and the start ( ) indicator will light up.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order, the
covers may be damaged.
D: Misfeed in the lower paper feed area (AL-1555)
Open the lower side cover
1
(under the manual tray) and
remove the misfed paper. If
blinks and the misfed
paper is not seen from the
area of the lower side cover,
pull out the lower paper tray
and remove the misfed
paper. Then close the lower
paper tray.
Close the lower side cover.
2
Close the side cover by pressing the round projections near
3
the side cover open button. The misfeed ( ) indicator will go
out and the start (
) indicator will light up.
E: Misfeed in the SPF (AL-1553), RSPF (AL1555)
An original misfeed may occur at one of three locations: if the misfed original is seen
from the original feeder tray, (A) in the original feeder tray; if the misfed original is not
seen from the original feeder tray, (B) in the exit area or (C) under the feeding roller.
Remove the misfed original following the instructions for each location.
(A) Open the feeding roller cover and pull the original gently to the left and out
from the original feeder tray. Close the feeding roller cover. Open and close
the SPF/RSPF to clear the SPF/RSPF misfeed (
original cannot be easily removed, proceed to (C).
) indicator. If the misfed
Feeding roller cover
66
Download from Www.Somanuals.com. All Manuals Search And Download.
(B) Open the SPF/RSPF and rotate the roller rotating knob to remove the
misfed original from the exit area. If the misfed original cannot be easily
removed, proceed to (C).
Roller rotating knob
(AL-1555)
With the RSPF, pull out the reversing tray to remove the misfed original.
With the RSPF, after removing the misfed original from the exit area,
be sure to insert the reversing tray into the exit area until it locks in
place.
Reversing tray
(C) If the original does not move easily into the exit area, remove it in the
direction of the arrow while rotating the knob.
8
A number may appear in the display after a minus sign, indicating the
number of the originals that must be returned to the original feeder tray.
Open and close the SPF/RSPF to clear the SPF/RSPF misfeed (
indicator, and then return the required number of originals. Then press
the start ( ) key to resume copying.
)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
9
SPECIFICATIONS
Model
AL-1552
AL-1553
AL-1555
Type
Digital multifunctional system, desk-top type
Dry, electrostatic transfer
Sheets, bound documents
Available
Copy system
Originals
Printer function
Scanner function
Paper tray
Available
250 sheets
250 sheets x 2
Single bypass, Multi-bypass Single bypass (1
Multi-bypass tray
(50 sheets)
tray
sheet)
100 sheets
—
Paper output tray
SPF/RSPF
SPF
RSPF
Original table/
Original sizes
Original feed
Max. A4
SPF/RSPF
Original table 1 sheet
SPF/RSPF
—
Up to 30 sheets
Copy/printing size
A6 to A4 *1
Max. 3 mm (Original table) *2
Max. 4 mm (SPF/RSPF) *2
Max. 4.5 mm *3
Image loss
Max. 6 mm *4
Copy speed
Print speed
15 pages/min.
12 pages/min. (A4)
Continuous copying/printing Max. 99 pages subtractive counter
First-copy/print time
(Approximately)
9.6 seconds *5
(paper:A4, exposure mode:AUTO, copy ratio:100% )
Variable:25% to 400% in 1% increments (total 376 steps)
Fixed: 25%, 70% 86%, 100%, 141%, 400%
Copy ratio
Moving optical source, slit exposure (stationary platen) with
automatic exposure
Original table
SPF/RSPF
Exposure
system
—
Moving original
Fusing system
Heat rollers
Development system
Light source
Magnetic brush development
Cold cathode fluorescent lamp
600 x 300dpi (Auto/Manual mode)
600 x 600dpi (Photo mode)
Copier
Resolution
Printer
600dpi
Scanner
600 x 1200dpi
256 levels
Scan
Gradation
Output
2 levels
Bit depth
1 bit or 8 bit/pixel
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
AL-1552
Colour CCD
Max. 2.88ms/line
16 MB
AL-1553
AL-1555
Sensor
Scanning speed
Memory
Local voltage 10% (For this copier’s power supply requirement,
see the name plate located on the back of the unit.)
Power supply
Power consumption
1000 W
Width (mm) 607.6
Depth (mm) 462.5
16kg
607.6
492.5
19kg
809.0
Overall
dimensions
Weight (Approximately) *6
23kg
Width (mm) 518.0
Depth (mm) 462.5
Height (mm) 295.6
Unit
dimensions
492.5
380.4
465.4
Temperature: 10°C to 30°C
Humidity: 20% to 85%
Operating conditions
Emulation
SHARP GDI
USB interface (USB1.1 Standard) /
IEEE1284-compliant bi-directional parallel interface (Only for
printer)
Interface port
Sound Power Level LwA (1B=10dB)
Copying: 6.0 [B], Standby: 3.7 [B]
Noise level
Sound Pressure Level LpA (bystander positions)
Copying: 46 [dB (A)], Standby: 23 [dB (A)]
Noise emission measurement in accordance with ISO 7779.
Emission concentration
Ozone: less than 0.02 mg/m3
(measurement according to Dust: less than 0.075 mg/m3
RAL-UZ 62)
Styrene: less than 0.07 mg/m3
*1 Feed paper lengthwise only.
*2 Leading and trailing edges.
*3 Along the other edges in totals.
*4 The trailing edge of the second (Two-sided copy mode).
*5 Data transmission time is not included. (Only for printer)
*6 Not including TD and drum cartridges.
As a part of our policy of continuous improvement, SHARP reserves the
right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are
nominal values of production units. There may be some deviations from
these values in individual units.
9
69
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT SUPPLIES AND OPTIONS
When ordering supplies, please use the correct part numbers as listed below.
Be sure to use only genuine SHARP parts and supplies.
For best copying results, be sure to use only SHARP Genuine
Supplies which are designed, engineered, and tested to maximise the
life and performance of SHARP copiers. Look for the Genuine
Supplies label on the toner package.
Supply list
Supply
Part number
AL-110DC
AL-100DR
Usable life
TD cartridge
Drum cartridge
Approx. 4,000 sheets*
Approx. 18,000 sheets
* Based on copying onto letter-type paper at 5% toned area
(The life of the TD cartridge which has been included in the unit at the factory is
approximately 2,000 sheets.)
Interface cable
Please purchase the appropriate cable for your computer.
Parallel interface cable
IEEE 1284-Shielded type bi-directional parallel interface cable (2m Max.)
USB interface cable
Shielded twisted pair cable, high-speed transmission equivalent (2m Max.)
70
Download from Www.Somanuals.com. All Manuals Search And Download.
MOVING AND STORING THE UNIT
Moving instructions
When moving the unit, follow the procedure below.
When moving this unit, be sure to remove the TD cartridge in advance.
Turn the power switch off and remove the power cord from the
outlet.
1
Open the side cover and front cover, in that order. Remove the
TD cartridge and close the front cover and side cover, in that
order.
2
To open and close the side cover and front cover, and to remove the TD
Raise the handle of the paper tray and pull the paper tray out
until it stops.
3
Push the centre of the pressure plate down until it locks in
place and lock the plate using the pressure plate lock which
has been stored in the front of the paper tray.
4
Push the paper tray back into the unit.
5
6
When shipping the unit, the scan head locking switch must be locked to
prevent shipping damage.
Close the multi-bypass tray (AL-1553, AL-1555) and attach the
7
packing materials and tape which were removed during
installation of the unit. See "PREPARING THE UNIT FOR
Pack the unit into the carton. See "CHECKING PACKED
8
Proper storage
Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
9
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl or get
damp, resulting in paper misfeeds.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
D
Acrobat Reader ................................. 43 Dark key ........................................ 6, 49
Alarm indicator
- Drum replacement required
Display................................................. 6
Displaying total number of copies ..... 56
indicator..............................6, 58, 62 Disposing of TD cartridge.................. 57
- Misfeed indicator ................6, 62, 63 Drum cartridge......................... 5, 58, 71
- TD cartridge replacement required
Drum cartridge replacement.............. 58
indicator..............................6, 57, 62 Drum replacement required
Appendix ........................................... 69 indicator................................... 6, 58, 62
Auto clear time .................................. 55
E
Auto power shut-off mode ................. 55
Exposure adjustment......................... 49
Exposure mode indicator............... 6, 49
Exposure mode selector key......... 6, 49
Automatic exposure adjustment ........ 50
B
Before installation.............................. 20
Button Manager........................... 19, 35
Bypass feed....................................... 17
Bypass paper guides...............5, 17, 18
F
Flow of installation............................. 21
Front cover .......................................... 5
Fusing unit release lever ............... 5, 64
C
H
Cautions
Handle................................................. 5
Hardware and software
- Handling ......................................... 2
- Label............................................... 1
- Laser .............................................. 2
- Using .............................................. 1
Charger cleaner............................. 5, 60
Checking packed components and
accessories ......................................... 8
Cleaning the unit
- Cabinet......................................... 59
- Original cover ............................... 59
- Original table ................................ 59
- SPF/RSPF....................................59
- SPF/RSPF scanning widow ......... 59
- Transfer charger........................... 60
Clear key .................................6, 47, 56
Connecting the interface cable
- Parallel interface cable................. 45
- USB interface cable......................45
Conventions used in this manual and
online manual......................................4
Copy flow........................................... 46
Copy quantity ....................................49
Copy quantity key....................6, 49, 55
Copy ratio display key ................... 6, 51
Copy ratio selector indicator.......... 6, 51
Copy ratio selector key..................6, 51
requirements ..................................... 20
How to print ....................................... 33
How to use the online manual........... 43
I
Indicators on the operation panel...... 32
Initial settings of operation panel....... 13
Installing the software.................. 19, 22
Installing the TD cartridge ................. 10
Interface
- Parallel interface........................... 45
- USB interface ............................... 45
Interface cable................................... 67
Interrupt copying................................ 47
Introduction.......................................... 4
L
Light and dark indicator................. 6, 49
Light key........................................ 6, 49
Loading paper ................................... 14
Loading the paper tray ...................... 15
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper storage................................... 71
M
Making copies ................................... 46
MFP driver
R
Reduction/enlargement/zoom ........... 51
- Print Status Window..................... 19
- Printer driver................................. 19
- Scanner driver.............................. 19
Misfeed indicator .....................6, 62, 63
Misfeed removal
- Fusing area .................................. 64
- Lower paper feed area ................. 66
- Paper feed area............................ 64
- SPF/RSPF....................................66
- Transport area.............................. 65
Moving instructions............................ 71
Multi-bypass tray ........................... 5, 17
S
Scan head locking switch.................... 9
Scanner driver................................... 19
SCANNER indicator ...................... 6, 32
SCANNER key .............................. 6, 39
Scanning from your computer ........... 40
Scanning with the "Scanner and
Camera Wizard" ................................ 42
Setting up the unit ............................... 7
Setup procedure.................................. 7
Sharpdesk ......................................... 19
Side cover ........................................... 5
Side cover open button ....................... 5
Single bypass................................ 5, 18
Software for the SHARP Personal
N
Name
- Operation panel.............................. 6
- Part names..................................... 5
MFP series ........................................ 19
Specifications .................................... 68
SPF/RSPF..................................... 5, 48
SPF/RSPF indicator ...................... 6, 48
SPF/RSPF misfeed indicator... 6, 62, 66
Start indicator ................................ 6, 32
Start key .................................. 6, 46, 56
Status indicators................................ 62
Stream feeding mode............ 49, 54, 55
Supplies and options......................... 70
Supply list
O
ONLINE indicator .......................... 6, 32
ONLINE key .................................. 6, 32
Online manual ............................... 4, 43
Opening the printer driver.................. 33
Opening the scan driver .................... 40
Operation panel...............................5, 6
Original placement
- Original table ................................ 47
- SPF/RSPF....................................48
Original table ................................. 5, 47
- Drum cartridge.............................. 70
- TD cartridge.................................. 70
P
T
Paper................................................. 14
Paper feed location indicator......... 6, 51
Paper output tray................................. 5
Paper output tray extension .......... 5, 46
Paper tray...................................... 5, 15
Parallel interface cable ................45, 70
Photo copying....................................49
Power cord socket............................... 5
Power off ........................................... 13
Power on ........................................... 12
Power save indicator..................... 6, 32
Power switch ................................. 5, 12
Preheat mode....................................55
Preparing the unit for installation......... 8
Printer driver...................................... 19
TD cartridge............................. 5, 10, 57
TD cartridge replacement.................. 57
TD cartridge replacement required
indicator................................... 6, 57, 62
Transfer charger............................ 5, 60
Tray select key .............................. 6, 51
Troubleshooting................................. 61
Troubleshooting the unit.................... 61
73
Download from Www.Somanuals.com. All Manuals Search And Download.
U
Z
USB interface cable..................... 45, 70 ZOOM indicator............................. 6, 51
Using other installed drivers .............. 44 ZOOM key..................................... 6, 51
Using the manuals............................... 4
Using the printer mode ......................33
Using the scanner mode ................... 35
Using the SHARP TWAIN ................. 40
INDEX BY PURPOSE
Cleaning the unit
- Lower paper feed area ................. 66
Copying ............................................. 46
Displaying total number of copies...... 56
Installing the software
Setting the copy quality
Loading paper
Setting the user program................... 55
- Paper tray..................................... 15 Storing the unit .................................. 71
Loading the original
Opening the printer driver.................. 33
Power off ........................................... 13
Power on ........................................... 12
Preparing for installation...................... 8
Printing .............................................. 33
74
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE LICENSE
PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY
USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF
THIS LICENSE.
1. License.
The application, demonstration, system and other software accompanying this License, whether on disk,
in read only memory, or on any other media (the "Software") and related documentation are licensed to
you by SHARP. You own the disk on which the Software is recorded but SHARP and/or SHARP'S
Licensors retain title to the Software and related documentation. This License allows you to use the
Software on one or more computers connected to a single printer and make one copy of the Software in
machine-readable form for backup purposes only. You must reproduce on such copy the SHARP
copyright notice, the copyright notice of SHARP’S Licensors and any other proprietary legends of
SHARP and/or its Licensors that were on the original copy of the Software. You may also transfer all
your license rights in the software, the backup copy of the Software, the related documentation and a
copy of this License to another party, provided the other party reads and agrees to the terms and
conditions of this License.
2. Restrictions.
The Software contains copyrighted material, trade secrets and other proprietary material which is owned
by SHARP and/or its Licensors and in order to protect them you may not decompile, reverse engineer,
disassemble or otherwise reduce the Software to a human-perceivable form. You may not modify,
network, rent, lease, loan, distribute or create derivative works based upon the Software in whole or in
part. You may not electronically transmit the Software from one computer to another or over a network.
3. Termination.
This license is effective until terminated. You may terminate this License at any time by destroying the
Software and related documentation and all copies thereof. This License will terminate immediately
without notice from SHARP and/or SHARP’S Licensors if you fail to comply with any provision of this
License. Upon termination you must destroy the Software and related documentation and all copies
thereof.
4. Export Law Assurances.
You agree and certify that neither the Software nor any other technical data received from SHARP, nor
the direct product thereof, will be exported outside the United States except as authorized and as
permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by
you outside of the United States, you agree that you will not re-export the Software nor any other
technical data received from SHARP, nor the direct product thereof, except as permitted by the laws and
regulations of the United States and the laws and the regulation of the jurisdiction in which you obtained
the Software.
5. Government End Users.
If you are acquiring the Software on behalf of any unit or agency of the United States Government, the
following provisions apply. The Government agrees:
(i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as
"Commercial Computer Software" and the Government is acquiring only "restricted rights" in the
Software and its documentation as that term is defined in Clause 252.227-7013 (c)(1) of the
DFARS; and
(ii) if the Software is supplied to any unit or agency of the United States Government other than DoD,
the Government's rights in the Software and its documentation will be as defined in Clause 52.227-
19 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52.227-86 (d) of the NASA
Supplement to the FAR.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Limited Warranty on Media.
SHARP warrants the disks on which the Software is recorded to be free from defects in materials and
workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced
by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy
will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6. A disk
will be replaced when it is returned to SHARP or a SHARP authorized representative with a copy of the
receipt. SHARP will have no responsibility to replace a disk damaged by accident, abuse or
misapplication.
ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO NINETY (90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM JURISDICTION TO JURISDICTION.
7. Disclaimer of Warranty on Software.
You expressly acknowledge and agree that use of the Software is at your sole risk. The software and
related documentation are provided "AS IS" and without warranty of any kind and SHARP and SHARP'S
Licensor(s) (for the purpose of provisions 7 and 8, SHARP and SHARP'S Licensor(s) shall be
collectively referred to as "SHARP") EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SHARP DOES NOT
WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR
REQUIREMENTS, OR THAT THE OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE
CORRECTED. FURTHERMORE, SHARP DOES NOT WARRANT OR MAKE ANY
REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE
SOFTWARE OR RELATED DOCUMENTATION IN TERMS OF THEIR CORRECTNESS,
ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR
ADVICE GIVEN BY SHARP OR A SHARP AUTHORIZED REPRESENTATIVE SHALL CREATE A
WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. SHOULD THE
SOFTWARE PROVE DEFECTIVE, YOU (AND NOT SHARP OR A SHARP AUTHORIZED
REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR
OR CORRECTION, SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
8. Limitation of Liability.
UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE, SHALL SHARP BE LIABLE FOR
ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE
USE OR INABILITY TO USE THE SOFTWARE OR RELATED DOCUMENTATION, EVEN IF
SHARP OR A SHARP AUTHORIZED REPRESENTATIVE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
In no event shall SHARP'S total liability to you for all damages, losses, and causes of action (whether in
contract, tort (including negligence) or otherwise) exceed the amount paid by you for the Software.
9. Controlling Law and Severability.
For a portion of the Software related with Apple Macintosh and Microsoft Windows, this license shall be
governed by and construed in accordance with the laws of the state of California and Washington,
respectively. If for any reason a court of competent jurisdiction finds any provision of this License, or
portion thereof, to be unenforceable, that provision of the License shall be enforced to the maximum
extent permissible so as to effect the intent of the parties, and the remainder of this License shall continue
in full force and effect.
10. Complete Agreement.
This License constitutes the entire agreement between the parties with respect to the use of the Software and
related documentation, and supersedes all prior or contemporaneous understandings or agreements, written
or oral, regarding such subject matter. No amendment to or modification of this License will be binding
unless in writing and signed by a duly authorized representative of SHARP.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 1/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-00831
MATERIAL SAFETY DATA SHEET
1. PRODUCT AND COMPANY IDENTIFICATION
AL-100TD / DM-150TD / AL-110TD / AL-110DC (Black Toner)
Sharp Corporation
Product Name
Supplier Identification
:
:
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Area
(Country)
U.S.A.
(Name and Telephone Number)
Sharp Electronics Corporation
Sharp Plaza, Mahwah, NJ
Telephone number for information
1-800-237-4277
1-800-255-3924
:
:
North
Emergency telephone number
Sharp Electronics of Canada Ltd.
Telephone number for information
Emergency telephone number
Sharp Corporation of Australia PTY. Ltd.
No1 Huntingwood Drive Huntingwood Blacktown N.S.W.
Telephone number for information
Sharp Electronics (Europe) GMBH
Sonninstrasse 3, 20097 Hamburg
Telephone number to access MSDS
For more information
America
Canada
Australia
Germany
905-890-2100
1-800-255-3924
:
:
Oceania
1300-13-50-22
:
040-2376-2185
040-2376-2613
:
:
United
Kingdom
France
Sharp Electronics (U. K.) Ltd.
Telephone number for information
Sharp Electronics France S.A.
Telephone number for information
Sharp Electronics GMBH
Telephone number for information
Sharp Electronics (Italy) S.P.A.
Telephone number for information
Sharp Electronics (Espana) S.A.
Telephone number for information
Sharp Electronics Benelux B.V.
Telephone number for information
Sharp Electronics Nordic AB
08705-274-277
01-49-90-34-00
01-727-19-0
02895951
:
:
:
:
:
:
:
:
Austria
Italy
Europe
Spain
93-581-97-00
30-6359500
08-634-36-00
01-846-6111
Netherlands
Sweden
Switzerland
U.A.E.
Telephone number for information
Sharp Electronics(Schweiz)AG
Telephone number for information
Sharp Middle East FZE
Middle
East
P.O.Box 17115 Jebel Ali, Dubai
Telephone number for information
04-815311
:
2. COMPOSITION / INFORMATION ON INGREDIENTS
Substance[ ]
Ingredient
Preparation[X]
CAS No.
Proportion
OSHA PEL
ACGIH TLV
MAK-TWA
NOHSC-TWA
Styrene-Acrylate
copolymer
29497-14-1
35-45%
Not listed
Not listed
Not listed
Not listed
Styrene-
9003-53-6
35-45%
Not listed
Not listed
Not listed
Not listed
Homopolymer
Carbon black
1333-86-4
1317-61-9
9010-79-1
8002-74-2
109125-51-1
84179-66-8
5-10%
5-10%
1-5%
1-5%
< 1%
3.5mg/m3
Not listed
Not listed
Not listed
0.5mg/m3
3.5mg/m3
Not listed
Not listed
Not listed
0.5mg/m3
Not listed
Not listed
Not listed
Not listed
Not listed
3mg/m3
Not listed
Not listed
Not listed
Not listed
Iron oxide
Polypropylene
Parafrfine
Metal Complex dye*
•
EC N0. : 400-110-2, Symbol letter : F, R Phrase : R11
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 2/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-00831
MATERIAL SAFETY DATA SHEET
3.HAZARDS IDENTIFICATION
Most Important Hazards and Effects of the Products
Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests
performed using toner. When used as intended according to instructions, studies do not
indicate any symptoms of fibrosis will occur.
Environmental Effects : No data are available.
Dust explosion (like most finely divided organic powders)
Not classified as dangerous
Specific Hazards
Directive 1999/45/EC(Europe)
:
:
4.FIRST-AID MEASURES
Route(s) of Entry : Inhalation?
Skin?
No
Ingestion?
Possible but very unusual.
Yes
Remove to fresh air. If symptoms occur, consult medical personnel.
Wash with soap and water for 15 minutes or until particle is removed.
If irritation does occur, consult medical personnel.
Inhalation
Skin Contact
:
:
Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical personnel.
Rinse with water and drink several glasses of water. If irritation or discomfort does occur, consult medical
personnel.
Eye Contact
Ingestion
:
:
5.FIRE-FIGHTING MEASURES
Water, CO , foam and dry chemicals
None
Toner material, like most finely divided organic powders, may form an explosive
Extinguishing Media
Special Fire Fighting Procedures
Fire and Explosion Hazards
:
:
:
2
mixture.
6.ACCIDENTAL RELEASE MEASURES
None
None
Personal Precautions
Environmental Precautions
Methods for Cleaning Up
:
:
:
Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is
released. It, like most finely divided organic powders, is capable of creating a dust
explosion.
7.HANDLING AND STORAGE
Handling
Technical Measures
: None
Precautions
: None
Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or during long
term exposure, as with any non-toxic dust. Try not to disperse the particles.
Storage
Technical Measures
: None
Storage Conditions
: Keep container closed and Store in a cool and dry place.
Keep out of the reach of children.
Incompatible Products : None
8.EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Measures
Ventilation
: Not required under intended use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 3/4
MATERIAL SAFETY DATA SHEET
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-00831
Personal Protective Equipment
Respiratory Protection
Hand Protection
Eye Protection
Skin Protection
: Not required under intended use.
: Not required under intended use.
: Not required under intended use.
: Not required under intended use.
Other Protective Equipment
: Use of a dust mask and goggles are recommended when handling a large
quantity of toner or during long term exposure, as with any non-toxic dust.
9.PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Physical State : Solid
Form : Powder
Color : Black
Odor : odorless
Not applicable
Not applicable
No data
Not applicable
No data
No data
1.1 (bulk density : 0.34)
Negligible
Ph
:
:
:
:
:
:
:
:
Boiling / Melting Point
Softening Point(°C)
Flash Point(°C)
lgnition Point(°C )
Explosion Properties
Density(g/cm³)
Solubility in Water
10.STABILITY AND REACTIVITY
Stable
Stability
:
:
:
:
:
:
Dust explosion, like most finely divided organic powders.
Hazardous Reactions
Conditions to Avoid
Materials to Avoid
Hazardous Decomposition Products
Further Information
Electric discharge, throwing into fire.
Oxidizing Materials
CO, CO2 and NOX
None
11.TOXICOLOGICAL INFORMATION
Acute Toxicity
Ingestion(oral)
Dermal
Inhalation
: LD50 > 2000mg/kg (Rats)
: LD50 > 2000mg/kg (Rats)
: No Data
Eye irritation
Skin irritation
Skin sensitizer
Mutagenicity
Carcinogenicity
: Not an irritant
: Not an irritant
: No sensitization
Negative (Ames Test)
:
In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human
:
carcinogen). This classification is given to chemicals for which there is inadequate human
evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The
classification is based upon the development of lung tumors in rats receiving chronic inhalation
exposures to free carbon black at levels that induce particle overload of the lung. Studies
performed in animal models other than rats did not show any association between carbon black
and lung tumors. Moreover,
a
two-year cancer bioassay using
a
typical toner preparation
containing carbon black demonstrated no association between toner exposure and tumor
development in rats.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 4/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-00831
MATERIAL SAFETY DATA SHEET
Chronic Effect
: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of
lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure
group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle
(4mg/m3) exposure group, but no pulmonary change was reported in the lowest (1mg/m3)
exposure group, the most relevant level to potential human exposures.
12.ECOLOGICAL INFORMATION
No data are available.
13.DISPOSAL CONSIDERATIONS
Waste from Residues
: Waste material may be dumped or incinerated under conditions which meet all federal,
state and local environmental regulations.
Contaminated Packaging : Waste may be disposed or incinerated under conditions which meet all federal, state and
local environmental regulations.
14.TRANSPORT INFORMATION
UN Classification
: None
Not classified as hazardous for transport.
15.REGULATORY INFORMATION
US Information
TSCA(Toxic Substances Control Act)
:
All chemical substances in this product comply with all applicable rules or order under TSCA.
SARA(Superfund Amendments and Reauthorization Act) Title III
302 Extreme Hazardous Substance : None
311/312 Hazard Classification
EU Information
: None
1999/45/EC and 67/548/EEC
Symbol & Indication
R-Phrase
: Not required
: Not required
76/769/EEC
: All chemical substances in this product comply with all applicable rules or
order under 76/769/EEC.
16.OTHER INFORMATION
NFPA Rating (USA)
: Health=1
Flammability=1
Reactivity=0
WHMIS Legislation (Canada)
List of R phrases
: This product is not a controlled product.
: R11 : Highly flammable
References
IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65,
Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
The information on this data sheet represents our current data and best opinion as to the proper use in handling of this
product under normal conditions. However, all materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we do not guarantee that these are the only hazards which exist.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 1/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-30831
MATERIAL SAFETY DATA SHEET
1.PRODUCT AND COMPANY IDENTIFICATION
AL-100TD / DM-150TD / AL-110TD / AL-110DC (Black Developer)
Sharp Corporation
Product Name
Supplier Identification
:
:
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Area
(Country)
U.S.A.
(Name and Telephone Number)
Sharp Electronics Corporation
Sharp Plaza, Mahwah, NJ
Telephone number for information
1-800-237-4277
1-800-255-3924
:
:
North
Emergency telephone number
Sharp Electronics of Canada Ltd.
Telephone number for information
Emergency telephone number
Sharp Corporation of Australia PTY. Ltd.
No1 Huntingwood Drive Huntingwood Blacktown N.S.W.
Telephone number for information
Sharp Electronics (Europe) GMBH
Sonninstrasse 3, 20097 Hamburg
Telephone number to access MSDS
For more information
America
Canada
Australia
Germany
905-890-2100
1-800-255-3924
:
:
Oceania
1300-13-50-22
:
040-2376-2185
040-2376-2613
:
:
United
Kingdom
France
Sharp Electronics (U. K.) Ltd.
Telephone number for information
Sharp Electronics France S.A.
Telephone number for information
Sharp Electronics GMBH
Telephone number for information
Sharp Electronics (Italy) S.P.A.
Telephone number for information
Sharp Electronics (Espana) S.A.
Telephone number for information
Sharp Electronics Benelux B.V.
Telephone number for information
Sharp Electronics Nordic AB
08705-274-277
01-49-90-34-00
01-727-19-0
02895951
:
:
:
:
:
:
:
:
Austria
Italy
Europe
Spain
93-581-97-00
30-6359500
08-634-36-00
01-846-6111
Netherlands
Sweden
Switzerland
U.A.E.
Telephone number for information
Sharp Electronics(Schweiz)AG
Telephone number for information
Sharp Middle East FZE
Middle
East
P.O.Box 17115 Jebel Ali, Dubai
Telephone number for information
04-815311
:
2.COMPOSITION / INFORMATION ON INGREDIENTS
Substance[ ]
Preparation[X]
Ingredient
CAS No.
Proportion
85-95%
1-5%
OSHA PEL
Not listed
ACGIH TLV
Not listed
MAK-TWA
Not listed
Not listed
NOHSC-TWA
Not listed
Iron powder
7439-89-6
29497-14-1
Styrene-Acrylate
copolymer
Not listed
Not listed
Not listed
Styrene homopolymer
9003-53-6
1333-86-4
1-5%
Not listed
3.5mg/m3
Not listed
3.5mg/m3
Not listed
Not listed
Not listed
3mg/m3
Carbon black
< 1.0%
3.HAZARDS IDENTIFICATION
Most Important Hazards and Effects of the Products
Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests
performed using toner. When used as intended according to instructions, studies do not
indicate any symptoms of fibrosis will occur.
Environmental Effects : No data are available.
Dust explosion (like most finely divided organic powders)
Specific Hazards
:
Directive 1999/45/EC(Europe) : Not classified as dangerous
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 2/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-30831
MATERIAL SAFETY DATA SHEET
4.FIRST-AID MEASURES
Route(s) of Entry : Inhalation?
Skin?
No
Ingestion?
Possible but very unusual.
Yes
Remove to fresh air. If symptoms occur, consult medical personnel.
Wash with soap and water for 15 minutes or until particle is removed.
If irritation does occur, consult medical personnel.
Inhalation
Skin Contact
:
:
Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical personnel.
Rinse with water and drink several glasses of water. If irritation or discomfort does occur, consult medical
personnel.
Eye Contact
Ingestion
:
:
5.FIRE-FIGHTING MEASURES
Water, CO , foam and dry chemicals
None
Toner material, like most finely divided organic powders, may form an explosive
Extinguishing Media
Special Fire Fighting Procedures
Fire and Explosion Hazards
:
:
:
2
mixture.
6.ACCIDENTAL RELEASE MEASURES
None
None
Personal Precautions
Environmental Precautions
Methods for Cleaning Up
:
:
:
Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is
released. It, like most finely divided organic powders, is capable of creating a dust
explosion.
7.HANDLING AND STORAGE
Handling
Technical Measures
: None
Precautions
: None
Safe Handling Advice
: Use of a dust mask is recommended when handling a large quantity of toner or during long term
exposure, as with any non-toxic dust. Try not to disperse the particles.
Storage
Technical Measures
: None
Storage Conditions
: Keep container closed and Store in a cool and dry place.
Keep out of the reach of children.
Incompatible Products : None
8.EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Measures
Ventilation
: Not required under intended use.
Exposure Limit Values
OSHA-PEL(USA)
ACGIH-TLV(USA)
: 15mg/m3 (Total Dust), 5mg/m3 (Respirable Dust)
: 10mg/m3 (Total Dust), 3mg/m3 (Respirable Dust)
Personal Protective Equipment
Respiratory Protection
Hand Protection
: Not required under intended use.
: Not required under intended use.
Eye Protection
: Not required under intended use.
Skin Protection
: Not required under intended use.
Other Protective Equipment
: Use of a dust mask and goggles are recommended when handling a large quantity of
toner or during long term exposure, as with any non-toxic dust.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 3/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-30831
MATERIAL SAFETY DATA SHEET
9.PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Physical State : Solid
Ph
Form : Powder
Not applicable
Not applicable
Not applicable
No data
No data
5.4 (bulk density 2.09)
Negligible
Color : Black
Odor : odorless
:
:
:
:
:
:
:
Boiling / Melting Point
Flash Point(°C)
lgnition Point(°C )
Explosion Properties
Density(g/cm³)
Solubility in Water
:
10.STABILITY AND REACTIVITY
Stable
Stability
:
:
:
:
:
:
Dust explosion, like most finely divided organic powders.
Electric discharge, throwing into fire.
Oxidizing Materials
CO, CO and NO
None
Hazardous Reactions
Conditions to Avoid
Materials to Avoid
Hazardous Decomposition Products
Further Information
2
X
11.TOXICOLOGICAL INFORMATION
Acute Toxicity
Ingestion(oral)
: LD50 > 2000mg/kg (Rats)
Inhalation
: No data
Dermal
: LD50>2000mg/kg(Rats)
: Not an irritant (Rabbits)
: Not an irritant (Rabbits)
: No sensitization
Eye irritation
Skin irritation
Skin sensitizer
Mutagenicity
Carcinogenicity
Negative (Ames Test)
:
:
In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen).
This classification is given to chemicals for which there is inadequate human evidence, but sufficient
animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the
development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels
that induce particle overload of the lung. Studies performed in animal models other than rats did not
show any association between carbon black and lung tumors. Moreover, a two-year cancer bioassay
using a typical toner preparation containing carbon black demonstrated no association between toner
exposure and tumor development in rats.
In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung
fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure group, and a
minimal to mild degree of fibrosis was noted in 22% of the animals in the middle (4mg/m3) exposure
group, but no pulmonary change was reported in the lowest (1mg/m3) exposure group, the most relevant
level to potential human exposures.
Chronic Effect
:
12.ECOLOGICAL INFORMATION
No data are available.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page: 4/4
Date Revised: Jul. 31. 2002
Date Issued : Jun. 1. 1998
MSDS No. F-30831
MATERIAL SAFETY DATA SHEET
13.DISPOSAL CONSIDERATIONS
Waste material may be dumped or incinerated under conditions which meet all federal,
state and local environmental regulations.
Waste from Residues
:
Waste may be disposed or incinerated under conditions which meet all federal, state and
local environmental regulations.
Contaminated Packaging
:
14.TRANSPORT INFORMATION
UN Classification
: None
Not classified as hazardous for transport.
15.REGULATORY INFORMATION
US Information
TSCA(Toxic Substances Control Act)
:
All chemical substances in this product comply with all applicable rules or order under TSCA.
SARA(Superfund Amendments and Reauthorization Act) Title III
302 Extreme Hazardous Substance : None
311/312 Hazard Classification
EU Information
: None
1999/45/EC and 67/548/EEC
Symbol & Indication
R-Phrase
: Not required
: Not required
76/769/EEC
: All chemical substances in this product comply with all applicable rules
or order under 76/769/EEC.
16.OTHER INFORMATION
NFPA Rating (USA)
: Health=1
Flammability=1
Reactivity=0
WHMIS Legislation (Canada)
References
: This product is not a controlled product.
IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65,
Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
The information on this data sheet represents our current data and best opinion as to the proper use in handling of this
product under normal conditions. However, all materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we do not guarantee that these are the only hazards which exist.
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this
equipment, please do not use the ordinary dust
bin!
Used electrical and electronic equipment must
be treated separately and in accordance with
legislation that requires proper treatment,
recovery and recycling of used electrical and
Attention: Your product is
electronic equipment.
marked with this symbol. It
means that used electrical
and electronic products
should not be mixed with
general household waste.
There is a separate
Following the implementation by member states,
private households within the EU states may
return their used electrical and electronic
equipment to designated collection facilities free
of charge*. In some countries* your local retailer
may also take back your old product free of
charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment
collection system for these
products.
has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes
the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health which could otherwise arise
due to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for
the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of
charge to the dealer, even if you don’t purchase a new product. Further collection
B. Information on Disposal for Business Users.
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the
product. You might be charged for the costs arising from take-back and recycling.
Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority
for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the
correct method of disposal.
Download from Www.Somanuals.com. All Manuals Search And Download.
The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are
applicable to the product. (This sentence is not applicable in any country where the above directives are not required.)
Required in Appendix ZB of BS 7002 (En 60 950) – United Kingdom
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-
rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or
ASTA approved fuse to BS1362 marked
removed from the plus must be used.
or
and of the same rating as the one
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the
plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied either cut-off the moulded plug (If this type is fitted) or remove by undoing the
screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code
below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed
immediately and disposed of in a safe manner. Under no circumstances shold the cut-off
plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following
code:
GREEN-AND-YELLOW:
BLUE:
BROWN:
Earth
Neutral
Live
As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in
the plug which is marked with the letter E, or by the safety earth symbol
, or coloured
green or green-and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with
the letter N or coloured black.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED IN FRANCE
TINSE1409TSZ1
Download from Www.Somanuals.com. All Manuals Search And Download.
|