®
SUPER
H8DCT-HLN4F
H8DCT-HIBQF
USER’S MANUAL
Revision 1.1a
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
About This Manual
This manual is written for system integrators, PC technicians and knowledgeable PC
users. It provides information for the installation and use of the H8DCT-HLN4F/HIBQF
serverboard.
The H8DCT-HLN4F/HIBQF serverboard is based on the AMD® SR5670 or SR5690
and SP5100 chipset and supports two AMD Socket C32 type processors with up
to 192 GB of ECC RDIMM.
The differences between the features of the H8DCT-HLN4F and H8DCT-HIBQF
serverboards are shown in the table below.
Features
H8DCT-HLN4F
H8DCT-HIBQF
SR5690SP5100 Chipset
SR5670/SP5100 Chipset
InfiniBand® Controller
2x 1Gb Ethernet LAN
4x 1Gb Ethernet LAN
Yes
Yes
Yes
Yes
Yes
Please refer to the motherboard specifications pages on our web site for updates on
to be professionally installed.
Manual Organization
Chapter 1 includes a checklist of what should be included in your motherboard
box, describes the features, specifications and performance of the motherboard
and provides detailed information about the chipset.
Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing
the motherboard in a chassis. Also refer to this chapter to connect the hard disk
drives, the various ports, and the power and reset buttons and the system LEDs.
If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the setup configuration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is
provided. Instructions are also included for contacting technical support. In addition,
you can visit our web site for more detailed information.
Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Chapter 1 Introduction
1-1
Overview ......................................................................................................... 1-1
Checklist.......................................................................................................... 1-1
Contacting Supermicro.................................................................................... 1-2
Serverboard Features ..................................................................................... 1-7
Chipset Overview.......................................................................................... 1-10
AMD AMD SR5670 or SR5690 and SP5100 Chipset .................................. 1-10
HyperTransport Technology .......................................................................... 1-10
PC Health Monitoring.................................................................................... 1-10
Power Configuration Settings.........................................................................1-11
Power Supply................................................................................................ 1-12
Super I/O....................................................................................................... 1-12
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Chapter 2 Installation
2-1
Standardized Warning Statements ................................................................. 2-1
About Standardized Warning Statements....................................................... 2-1
Static-Sensitive Devices.................................................................................. 2-4
Precautions ..................................................................................................... 2-4
Unpacking ....................................................................................................... 2-4
Processor and Heatsink Installation................................................................ 2-5
Mounting the Serverboard into a Chassis ...................................................... 2-7
Installing Memory............................................................................................ 2-7
Memory Support.............................................................................................. 2-8
Maximum Memory........................................................................................... 2-8
DIMM Module Population Configuration .................................................... 2-9
PCI Expansion Cards.................................................................................... 2-10
I/O Port and Control Panel Connections .......................................................2-11
Connector Definitions.................................................................................... 2-12
Fan Header .............................................................................................. 2-12
LAN1/2/3/4 (Ethernet Ports)..................................................................... 2-12
Unit Identifier Button................................................................................. 2-12
IPMB......................................................................................................... 2-13
Overheat LED........................................................................................... 2-13
USB Headers ........................................................................................... 2-13
JP1 Adapter Card Connector................................................................... 2-13
Trusted Platform Module Header............................................................. 2-14
2-2
2-3
2-4
2-5
2-6
2-7
2-8
v
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
SXB1 Adapter Card Slot/Connector......................................................... 2-14
2-9
Jumper Settings ............................................................................................ 2-15
Explanation of Jumpers ................................................................................ 2-15
CMOS Clear............................................................................................. 2-15
I2C to PCI-Express Slots ......................................................................... 2-16
BMC Jumper ............................................................................................ 2-16
VGA Enable/Disable................................................................................. 2-16
LAN Enable/Disable ................................................................................ 2-16
InfiniBand Port Enable/Disable ............................................................... 2-16
Watch Dog Enable/Disable ...................................................................... 2-17
2-10 Onboard Indicators........................................................................................ 2-17
LAN1/LAN2/LAN3/LAN4 LEDs................................................................. 2-17
Power LED ............................................................................................... 2-17
Dedicated IPMI LAN LEDs ..................................................................... 2-18
InfiniBand LED Indicators......................................................................... 2-18
IPMI LED.................................................................................................. 2-18
UID LED (LE1) ........................................................................................ 2-19
2-11 Enabling SATA RAID..................................................................................... 2-20
Serial ATA (SATA).......................................................................................... 2-20
Installing the OS/SATA Driver ....................................................................... 2-20
Building a Driver Diskette......................................................................... 2-20
Enabling SATA RAID in the BIOS................................................................. 2-21
Using the DotHill and Adaptec RAID Utility .................................................. 2-23
Installing the RAID Driver During OS Installation......................................... 2-23
2-12 Installing Drivers............................................................................................ 2-24
Supero Doctor III........................................................................................... 2-25
2-13 Serverboard Battery...................................................................................... 2-27
Chapter 3 Troubleshooting
3-1
Troubleshooting Procedures ........................................................................... 3-1
Before Power On ............................................................................................ 3-1
No Power ........................................................................................................ 3-1
No Video ......................................................................................................... 3-2
Memory Errors ............................................................................................... 3-2
Losing the System’s Setup Configuration....................................................... 3-2
Technical Support Procedures........................................................................ 3-2
Frequently Asked Questions........................................................................... 3-3
3-2
3-3
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
3-4
Returning Merchandise for Service................................................................. 3-4
Chapter 4 BIOS
4-1
4-2
4-3
4-3
Introduction...................................................................................................... 4-1
Main Menu ...................................................................................................... 4-2
Advanced Settings Menu................................................................................ 4-2
Security Menu ............................................................................................... 4-15
4-4
4-5
Boot Menu..................................................................................................... 4-16
Exit Menu ...................................................................................................... 4-17
Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes
B-1
B-2
B-3
Uncompressed Initialization Codes.................................................................B-1
Bootblock Recovery Codes.............................................................................B-2
Uncompressed Initialization Codes.................................................................B-3
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
•
One (1) H8DCT-HLN4F/HIBQF serverboard
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your motherboard.
•
•
•
Supermicro product manuals: http://www.supermicro.com/support/manuals/
Product drivers and utilities: ftp://ftp.supermicro.com
Product safety information:
•
If you have any questions, please contact our support team at:
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
1-2 Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
Tel:
Fax:
Email:
+1 (408) 503-8008
[email protected] (General Information)
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
Web Site:
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
Tel:
+886-(2)-8226-3990
Web Site:
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Figure 1-1. H8DCT-HLN4F Image
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 1-1. H8DCT-HIBQF Image
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Figure 1-2. H8DCT-HLN4F/HIBQF Serverboard Layout
(not drawn to scale)
KVM
LE1
LE2
LE3
UID
JIB1
DP1
BMC
InfiniBand
NIC
SPEAKER
DP2
AMD
SR5670
or
SR5690
AMD
SP5100
CPU1
CPU2
Notes:
Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
H8DCT-HLN4F/HIBQF Quick Reference
Jumper
JBT1
Description
Default Setting
(See Section 2-8)
Pins 1-2 (Enabled)
Open (Disabled)
CMOS Clear
JIB1
InfiniBand Enable/Disable
I2C to PCI-E Slot Enable/Disable
BMC Enable/Disable
VGA Enable/Disable
JI2C1/JI2C2
JPB1
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
JPG1
LAN 1/2 Enable/Disable (LAN 1/2/3/4 for
H8DCT-HLN4F)
JPL1
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
JWD1
Watch Dog Enable/Disable
LED
Description
LAN Ports
LEDs for the LAN Ethernet ports
Dedicated IPMI LAN
LEDs for the dedicated IPMI LAN Ethernet port
LED for UID Button
LE1
LE2
LE3
DP1
DP2
InfiniBand Physical Link LED (Green) (H8DCT-HIBQF only)
InfiniBand Logical Link LED (Yellow) (H8DCT-HIBQF only)
LED for IPMI activity
LED for Serverboard Power-On
Connector
GPU FAN 1
JIPMB1
IPMI LAN
JB1
Description
GPU Fan Header
System Management Bus Header (SMBus)
Dedicated IPMI LAN Port
InfiniBand Connector
JOH1
Overheat Warning Header
JTPM1
JP1
Trusted Platform Module Header
SMC Proprietary Slot for Power, FP Control & SATA connectors
Keyboard/Video/Mouse Port
Gigabit Ethernet (RJ45) Ports
Unit Identifier Button
KVM
LAN1/2/3/4
UID
USB2/3
Universal Serial Bus (USB) Ports, Headers
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-3 Serverboard Features
CPU
•
Dual AMD Opteron 4000 series (AMD Socket C32 type) processors
Note: Refer to our web site for details on supported processors.
Memory
•
Up to twelve (12) slots of single/dual-channel DIMMs supporting up to 192 GB
of ECC RDIMM DDR3-1600/1333/1066 MHz speed SDRAM memory in
1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules of 1.5V or
1.35V voltages.
Note: Refer to Section 2-5 before installing memory and our web site for recommended DIMMs.
Chipset
•
AMD SR5670 (H8DCT-HLN4F) or SR5690 (H8DCT-HIBQF) chipset and one
SP5100 Southbridge chipset
Expansion Slots
•
One (1) PCI-Express x16 Gen. 2
•
One (1) PCI-Express x8 Gen. 2 (in x4 slot; for adapter card)
BIOS
•
•
16 Mb AMIBIOS® SPI Flash ROM
DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS 2.3, Real
Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys, Hardware
BIOS Virus Protection
PC Health Monitoring
•
Onboard voltage monitors
•
•
•
•
•
•
•
•
•
Fan status monitor with firmware/software on/off and speed control
Watch Dog
Environmental temperature monitoring via BIOS
Power-up mode control for recovery from AC power loss
System resource alert (via included utility program)
Auto-switching voltage regulator for the CPU core
CPU thermal trip support
I2C temperature sensing logic
Chipkill Support
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
ACPI Features
•
•
•
Microsoft OnNow
Slow blinking LED for suspend state indicator
BIOS support for USB keyboard
Onboard I/O
•
Four (4) USB (Universal Serial Bus 2.0) ports (two via headers, two via KVM
ports)
•
Up to four (4) LAN ports supported by one onboard Intel® i350 Ethernet
controller for 10/100/1000Base-T (Four for the H8DCT-HLN4F or two for
the H8DCT-HIBQF)
•
•
•
One (1) dedicated IPMI LAN port
One (1) KVM (VGA+COM+2*USB) port
One Mellanox Connect-X2 InfiniBand port supporting a single QSFP connector
(only for H8DCT-HIBQF)
Other
•
Onboard power LED
Utilities
•
•
•
BIOS flash upgrade utility
Super Doctor III
IPMI 1.5 / 2.0
Dimensions
•
Proprietary format: (LxW) 6.8" x 16.64" (173 x 423 mm)
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Figure 1-3. AMD SR5670 or SR5690 and SP5100 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your serverboard. See the previous pages for the
actual specifications of your serverboard.
HT3 Link
16 x16 bits 6.4GT/s
CH 2
CH 1
CH 2
CH 1
AMD
Socket C32
CPU2
AMD
Socket C32
CPU1
HT3 Link
16 x16 bits 6.4GT/s
DDR3
1600/1333/1066 MT/s
DDR3
1600/1333/1066 MT/s
HT3 Link
16x16 bits 5.2GT/s
RJ45
RJ45
RJ45
RJ45
PCI-E GEN2 X16 PCI-E Slot1
INTEL
I350
SR5690
or
SR5670
PCI-E GEN2 X8
PCI-E GEN2 X8
PCI-E Slot2
PCI-E GEN2 X4
Mellanox
Connect-X2
NCSI
A-Link
PCI
SMBus
LPC
DDR2 SDRAM
64Mb X16bit
SATA x6
BMC
VGA
WPCM450-R
PSU I2C
SP5100
Hot Plug
CONN
IPMB
SIO
W83527
SPI Flash
HWM
FE PHY
W83795G
RTL8201N
JKVM
VGA
COM
USB
USB
Header
RJ45
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
1-4 Chipset Overview
The H8DCT-HLN4F/HIBQF serverboard is based on the AMD
AMD SR5670 or SR5690 and SP5100 chipset. This chipset functions as a Media
and Communications Processor (MCP). Controllers for the system memory are
integrated directly into AMD Opteron processors.
AMD AMD SR5670 or SR5690 and SP5100 Chipset
The AMD AMD SR5670 or SR5690 and SP5100 chispsets are each a single-chip,
high-performance HyperTransport peripheral controller. They include a 30 or 42-
lane PCI Express interface, an AMD Opteron 16-bit Hyper Transport interface link,
a six-port Serial ATA interface and a four-port USB 2.0 interface. This hub connects
directly to the CPU.
HyperTransport Technology
HyperTransport technology is a high-speed, low latency point to point link that was
designed to increase the communication speed by a factor of up to 48x between
integrated circuits. This is done partly by reducing the number of buses in the
chipset to reduce bottlenecks and by enabling a more efficient use of memory
in multi-processor systems. The end result is a significant increase in bandwidth
within the chipset.
1-5 PC Health Monitoring
ThissectiondescribesthePChealthmonitoringfeaturesoftheH8DCT-HLN4F/HIBQF
serverboard. The serverboard has an onboard System Hardware Monitor chip that
supports PC health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once
a voltage becomes unstable, it will give a warning or send an error message to
the screen. Users can adjust the voltage thresholds to define the sensitivity of the
voltage monitor. Real time readings of these voltage levels are all displayed in BIOS.
Fan Status Monitor with Firmware/Software Speed Control
The PC health monitor can check the RPM status of the cooling fans. The onboard
fans are controlled by thermal management via BIOS.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
CPU Overheat/Fan Fail LED and Control
This feature is available when the user enables the CPU overheat/Fan Fail warning
function in the BIOS. This allows the user to define an overheat temperature. When
this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail
warning LED is triggered.
Auto-Switching Voltage Regulator for the CPU Core
The 5-phase-switching voltage regulator for the CPU core can support up to
AMD Opteron 4000 series processors and auto-sense voltage IDs ranging from 0.8
V to 1.55V. This will allow the regulator to run cooler and thus make the system
more stable.
1-6 Power Configuration Settings
This section describes the features of your motherboard that deal with power and
power settings.
Microsoft OnNow
The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for a PC that is always on but appears
to be off and responds immediately to user or other requests.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If a USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.
Note: To wake up the system from an S4 state by the USB keyboard/mouse, please
connect the keyboard/mouse to USB port 0/1 at the rear I/O side.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Main Switch Override Mechanism
The power button can function as a system suspend button. When the user
depresses the power button, the system will enter a SoftOff state. The monitor
will be suspended and the hard drive will spin down. Depressing the power button
again will cause the whole system to wake-up. During the SoftOff state, the power
supply provides power to keep the required circuitry in the system alive. In case the
system malfunctions and you want to turn off the power, just depress and hold the
power button for 4 seconds. The power will turn off and no power will be provided
to the motherboard.
1-7 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The H8DCT-HLN4F/HIBQF serverboard requires the use of proprietary power
supplies. Please refer to the pinout information for the power connectors in Section
7 of Chapter 2 for detailed information on power requirements.
In areas where noisy power transmission is present, you may choose to install a
line filter to shield the computer from noise. It is recommended that you also install
a power surge protector to help avoid problems caused by power surges.
Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.
1-8 Super I/O
The disk drive adapter functions of the Super I/O Winbond® BMC chip includes a
data separator, write pre-compensation circuitry, decode logic, data rate selection,
a clock generator, drive interface control logic and interrupt and DMA logic. The
wide range of functions integrated onto the Super I/O greatly reduces the number
of components required for interfacing with floppy disk drives.
The Super I/O provides two high-speed, 16550 compatible serial communication
ports (UARTs), one of which supports serial infrared communication. Each UART
includes a 16-byte send/receive FIFO, a programmable baud rate generator,
complete modem control capability and a processor interrupt system. Both UARTs
provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced
speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed
modems.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
The Super I/O provides functions that comply with ACPI (Advanced Configuration
and Power Interface), which includes support of legacy andACPI power management
through a SMI or SCI function pin. It also features auto power management to reduce
power consumption.
The IRQs, DMAs and I/O space resources of the Super I/O can be flexibly adjusted
to meet ISA PnP requirements, which support ACPI and APM (Advanced Power
Management).
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Chapter 2
Installation
2-1 Standardized Warning Statements
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this section in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.
com/about/policies/safety_information.cfm.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同
等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!
אזהרה ף להחלי יש .תקינה לא בדרך והוחלפה במידה הסוללה של פיצוץ סכנת קיימת .
מומלצת יצרן מחברת התואם בסוג הסוללה את .
היצרן הוראות לפי לבצע יש המשומשות הסוללות סילוק ﻚ ﻓﻌﻠﻴ ﺻﺤﻴﺤﺔ ﻏﻴﺮ ﺑﻄﺮﻳﻘﺔ ﺍﻟﺒﻄﺎﺭﻳﺔ ﺍﺳﺘﺒﺪﺍﻝ ﺣﺎﻟﺔ ﻓﻲ ﺍﻧﻔﺠﺎﺭ ﻣﻦ ﺧﻄﺮ ﻫﻨﺎﻙ ﺔ ﺍﻟﺒﻄﺎﺭﻳ ﺍﺳﺘﺒﺪﺍﻝ ﺔ ﺍﻟﻤﺼﻨﻌ ﺍﻟﺸﺮﻛﺔ ﺑﻪ ﺃﻭﺻﺖ ﻛﻤﺎ ﻳﻌﺎﺩﻟﻬﺎ ﻣﺎ ﺃﻭ ﺍﻟﻨﻮﻉ ﺑﻨﻔﺲ ﻓﻘﻂ ﺔ ﺍﻟﺼﺎﻧﻌ ﺍﻟﺸﺮﻛﺔ ﻟﺘﻌﻠﻴﻤﺎﺕ ﻭﻓﻘﺎ ﺍﻟﻤﺴﺘﻌﻤﻠﺔ ﺍﻟﺒﻄﺎﺭﻳﺎﺕ ﻣﻦ ﺗﺨﻠﺺ 경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国 の関係する全ての法律
・条例に従い処理する必要
が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
ר המוצ סילוק !
אזהרה .
המדינה וחוקי להנחיות בהתאם להיות חייב זה מוצר של סופי סילוק ﺔ ﺍﻟﻮﻁﻨﻴ ﻭﺍﻟﻠﻮﺍﺋﺢ ﺍﻟﻘﻮﺍﻧﻴﻦ ﻟﺠﻤﻴﻊ ﻭﻓﻘﺎ ﻣﻌﻪ ﺍﻟﺘﻌﺎﻣﻞ ﻳﻨﺒﻐﻲ ﺍﻟﻤﻨﺘﺞ ﻫﺬﺍ ﻣﻦ ﺍﻟﻨﻬﺎﺋﻲ ﺍﻟﺘﺨﻠﺺ ﻋﻨﺪ 경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-2 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic components. To prevent
damage to your system board, it is important to handle it very carefully. The following
measures are generally sufficient to protect your equipment from ESD.
Precautions
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic
bag.
•
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not
in use.
•
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
•
Use only the correct type of CMOS onboard battery as specified by the
manufacturer. Do not install the CMOS onboard battery upside down, which
may result in a possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-3 Processor and Heatsink Installation
Caution: Exercise extreme caution when handling and installing the processor. Always
connect the power cord last and always remove it before adding, removing or changing
any hardware components.
Installation Procedure
Follow the procedures as listed below to install the motherboard into a chassis.
1. Install the processor(s) and the heatsink(s).
2. Install the motherboard in the chassis.
3. Install the memory and add-on cards.
4. Finally, connect the cables and install the drivers.
Installing the Processors
1. Begin by removing the cover plate
that protects the CPU. Lift the
lever on the CPU socket until it
points straight up. With the lever
raised, lift open the silver CPU
retention plate.
2. Use your thumb and your index
finger to hold the CPU. Locate
and align pin 1 of the CPU socket
with pin 1 of the CPU. Both are
marked with a triangle.
Triangles
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
3. Align pin 1 of the CPU with pin
1 of the socket. Once aligned,
carefully place the CPU into the
socket. Do not drop the CPU
on the socket, move the CPU
horizontally or vertically or rub the
CPU against the socket or against
any pins of the socket, which
may damage the CPU and/or the
socket.
4. With the CPU inserted into the
socket, inspect the four corners
of the CPU to make sure that it is
properly installed and flush with
the socket. Then, gently lower
the silver CPU retention plate into
place.
Installing the Heatsinks
We recommend the use of active type heatsinks (except for 1U systems). Use any
onboard fan header for the CPU's heatsink fan. To install the heatsink, please follow
the installation instructions that are included with your heatsink package.
Note: Make sure the heatsink is placed so that the fins of the heatsink are in the
direction of the airflow in your system.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-4 Mounting the Serverboard into a Chassis
All motherboards have standard mounting holes to fit different types of chassis.
Make sure that the locations of all the mounting holes for both the motherboard
and the chassis match. Although a chassis may have both plastic and metal
mounting fasteners, metal ones are highly recommended because they ground
the motherboard to the chassis. Make sure that the metal standoffs click in or are
screwed in tightly.
Check the Compatibility of the Serverboard Ports and the I/O Shield
1. The H8DCT-HLN4F/HIBQF serverboard requires a chassis that can support a
board of (LxW) 6.8" x 16.64" (173 x 423 mm) in size.
2. Make sure that the I/O ports on the motherboard align with their respective
holes in the I/O shield at the rear of the chassis.
Mounting the Serverboard onto the Tray in the Chassis
1. Carefully mount the motherboard onto the motherboard tray by aligning the
motherboard mounting holes with the raised metal standoffs in the tray.
2. Insert screws into all the mounting holes in the motherboard that line up with
the standoffs.
3. Then use a screwdriver to secure the motherboard to the mainboard
tray - tighten until just snug (if too tight you might strip the threads). Metal
screws provide an electrical contact to the motherboard ground to provide a
continuous ground for the system.
Caution: Exercise extreme caution when installing or removing memory modules to
prevent any possible damage.
2-5 Installing Memory
Installing Memory
1. Insert each memory module vertically into its slot, paying attention to the
notch along the bottom of the module to prevent inserting the module
incorrectly (see Figure 2-1).
2. Install to slots CPU1/DIMM1A, CPU1/DIMM2A, etc. Always install in groups
of two and in the numerical order of the DIMM slots. See support information
below.
3. Gently press down on the memory module until it snaps into place.
4. With two DIMMs installed, repeat step 2 to populate the CPU2 DIMM
slots. Always install two DIMMs to both CPU DIMM slots for more efficient
operation.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Note: 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules are
supported. It is highly recommended that you remove the power cord from the
system before installing or changing memory modules. Please refer to our web
site for memory that has been tested on the H8DCT-HLN4F/HIBQF serverboard.
Figure 2-1. Installing DIMM into Slot
To Install: Insert
module vertically and
press down until it
snaps into place.
Pay attention to the
alignment notch at
the bottom.
Notch
Notch
Front View
Note: Notch should align with
the receptive key point on
the slot.
To Remove: Use
your thumbs to gently
push the release tabs
near both ends of the
module. This should
release it from the
slot.
Release Tab
Release Tab
Top View of DDR3 Slot
Memory Support
The H8DCT-HLN4F/HIBQF serverboard supports single/dual-channel,
DDR3-1600/1333/1066 MHz registered ECC/Unbuffered ECC/non-ECC SDRAM
memory modules.
Populating two adjacent slots at a time with memory modules of the same size and
type will result in interleaved (128-bit) memory, which is faster than non-interleaved
(64-bit) memory.
Maximum Memory
The H8DCT-HLN4F/HIBQF serverboard supports a maximum of up to 192 GB of
ECC RDIMM SDRAM memory in twelve (12) DIMM slots.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Memory Population for Optimal Performance
-For a Serverboard with One CPU (CPU1) Installed
# DIMMS
2 DIMMs
4 DIMMs
6 DIMMs
CPU
CPU1
CPU1
CPU1
Channel 1
Channel 2
P1-1A
P1-1A
P1-1A
P1-2A
P1-2A
P1-2A
P1-1C
P1-1C
P1-2C
P1-2C
P1-1B
P1-2B
Memory Population for Optimal Performance
-For a Serverboard with Two CPUs (CPU1 & CPU2) Installed
# DIMMS
CPU
CPU1
CPU2
CPU1
CPU2
CPU1
CPU2
Channel 1
Channel 2
P1-1A
P2-1A
P1-1A
P2-1A
P1-1A
P2-1A
P1-2A
P2-2A
P1-2A
P2-2A
P1-2A
P2-2A
4 DIMMs
P1-1C
P2-1C
P1-1C
P2-1C
P1-2C
P2-2C
P1-2C
P2-2C
8 DIMMs
P1-1B
P2-1B
P1-2B
P2-2B
12 DIMMs
DIMM Module Population Configuration
For memory to work properly, follow the tables below for memory installation:
Per Channel DIMM Populations Options
Max.
MHz, 1.5V
DIMMs
Max. MHz,
1.35V DIMMs
Max. GB/
Channel
DIMM Type
DIMM A DIMM B DIMM C
SR or DR
SR
Empty
Empty
Empty
Empty
Empty
SR
Empty
SR
1600 MHz
1333 MHz
1066 MHz
1600 MHz
1333 MHz
1066 MHz
1066 MHz
1066 MHz
800 MHz
1333 MHz
1333 MHz
1066 MHz
1333 MHz
1333 MHz
800 MHz
1066 MHz
800 MHz
800 MHz
8 GB
8 GB
Unbuffered
DIMM
DR
DR
16 GB
16 GB
8 GB
SR or DR
SR
Empty
SR
SR
SR
12 GB
32 GB
32 GB
48 GB
Registered
DIMM
DR
Empty
QR
DR
Empty
DR
Empty
DR
DR
Note 1: Due to OS limitations, some operating systems may not show more than
4 GB of memory.
Note 2: Due to memory allocation to system devices, the amount of memory that
remains available for operational use will be reduced when 4 GB of RAM is used.
The reduction in memory availability is disproportional.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-6 PCI Expansion Cards
A riser card is used to support one standard size (full height full length) PCI
expansion card.
Installing a PCI Expansion Card
1. Confirm that you have the correct riser card for your chassis model and the
add-on card includes a standard bracket.
2. Remove the chassis cover.
3. Install the riser card by sliding card into the appropriate slot in the
serverboard.
4. Choose the PCI slot shield in which to place the add-on card.
5. In that slot, open the PCI slot shield lever and slide the shield sideways.
6. From inside the chassis, remove the PCI slot shield.
7. Slide the add-on card into the riser card and attach the add-on card bracket
in place of the PCI slot shield.
8. Secure the add-on card by closing the PCI slot shield lever.
9. Connect cables to the add-on card as necessary.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-7 I/O Port and Control Panel Connections
The I/O ports are color coded to make setting up your system easier. See Figure
2-2 below for the colors and locations of the various I/O ports.
Figure 2-2. I/O Port Locations and Definitions
1
3
4
2
5
6
7
8
Rear I/O Ports
1. LAN3
3. LAN4
5. IPMI LAN
7. InfiniBand Port
(H8DCT-HLN4F Only)
(H8DCT-HLN4F Only)
(H8DCT-HIBQF Only)
2. LAN1
4. LAN2
6. KVM
8. UID
(VGA+COM+2*USB)
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-8 Connector Definitions
Fan Header
Fan Header
Pin Definitions
This motherboard has one GPU fan
header (GPU_Fan1). This 4-pin fans
header is backward compatible with
3-pin fans. However, fan speed control
is available for 4-pin fans only. The
fan speeds are controlled by firmware
thermal management via IPMI 2.0..
See the table on the right for pin
definitions
Pin# Definition
1
2
3
4
Ground
+12V
Tachometer
PWR Modulation
LAN1/2/3/4 (Ethernet Ports)
LAN Ports (LAN1/2/3/4)
Pin Definition
Up to four Gigabit Ethernet ports
(designated LAN1, LAN2, LAN3 and
LAN4) are located on the rear of the
serverboard. The H8DCT-HIBQF has
two ports whereas the H8DCT-HLN4F
has four. Additionally, there is a
dedicated LAN for IPMI next to the
four rear LAN ports. These Ethernet
ports accept RJ45 type cables.
Pin# Definition
Pin# Definition
1
2
3
4
P2V5SB
TD0+
10
11
12
13
SGND
Act LED
P3V3SB
TD0-
TD1+
Link 100 LED
(Yellow, +3V3SB)
5
TD1-
14
Link 1000 LED
(Yellow, +3V3SB)
6
7
8
9
TD2+
TD2-
TD3+
TD3-
15
16
17
18
Ground
Ground
Ground
Ground
NC indicates no connection.
Unit Identifier Button
UID Button
Pin Definitions
In addition to the UID (Unit Identifier)
button on the rear I/O panel, there
is another UID button located on the
control panel. When you push either
UID button, both Rear UID and Front
Panel UID Indicators will illuminate.
Push either button again to turn off
both indicators. These UID indicators
provide easy identification of a system
unit that may be in need of service.
Pin# Definition
1
2
3
4
Ground
Ground
Button In
Ground
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
IPMB
JIPMB1
Pin Definitions
A System Management Bus header
for the IPMI slot is located at JIPMB1.
Connect the appropriate cable here to
use the IPMB I2C connection on your
system.
Pin# Definition
1
2
3
4
Data
Ground
Clock
No Connection
Overheat LED
Overheat LED
Pin Definitions
(JOH1)
Connect an LED to the JOH1
header to provide warning of chassis
overheating. See the table on the right
for pin definitions.
Pin# Definition
1
2
3.3V
OH Active
USB Headers
Universal Serial Bus Headers
Pin Definitions
Two USB 2.0 headers (USB2/3) are
also included on the motherboard.
These may be connected to provide
front side access. A USB cable (not
included) is needed for the connection.
See the table on the right for pin
definitions.
(USB2/3)
JUSB1
Pin# Definition
Pin# Definition
1
3
5
7
9
+5V
2
+5V
PO-
4
PO-
PO+
Ground
Key
6
PO+
Ground
NC
8
10
Note: NC indicates no connection.
JP1 Adapter Card Connector
JP1 Adapter card connector slot
provides front access to the power
supply, serial ATA and Front Panel
Control connections for the H8DCT
series motherboards. Plug an Adapter
card into this connector to use the
functions indicated above. This
connector is designed specifically for
a Supermicro-proprietary adapter card.
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Trusted Platform Module Header
Trusted Platform Module
Header Pin Definitions (JTPM1)
The JTPM1 header is used to connect
a Trusted Platform Module (TPM),
available separately from a third-party
vendor. A TPM is a security device that
allows encryption and authentication of
hard drives, disallowing access if the
TPM associated with it is not installed
in the system. See the table on the
right for pin definitions.
Pin# Definition
Pin# Definition
1
LCLK
2
4
6
8
GND
3
LFRAME
LRESET
LAD3
No Pin
VCC5
LAD2
5
7
9
VCC3
LAD0
10 LAD1
12 GND
11
13
15
17
19
RSV0
14 RSV1
16 SERIRQ
18 CLKRUN
20 RSV2
SB3V
GND
LPCPD
SXB1 Adapter Card Slot/Connector
A PCI-Express 2.0 x8 (in x4) slot
(SXB1) is located at JPCIE2 on the
motherboard. This slot is used for an
SMC proprietary SAS adapter card.
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-9 Jumper Settings
3
2
1
Connector
Pins
Explanation of Jumpers
To modify the operation of the
motherboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identified with a
square solder pad on the printed circuit
board. See the diagram at right for
an example of jumping pins 1 and 2.
Refer to the motherboard layout page
for jumper locations.
Jumper
Setting
3
2
1
Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.
JBT1 contact pads
CMOS Clear
JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To Clear CMOS
1. First power down the system and unplug the power cord(s). It is also
recommended that you remove the onboard battery from the serverboard.
2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.
3. Remove the screwdriver (or shorting device).
4. Reconnect the power cord(s) and power on the system.
Note 1. For an ATX power supply, you must completely shut down the system,
remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2. Be sure to remove the onboard CMOS Battery before you short JBT1 to
clear CMOS.
Note 3. Clearing CMOS will also clear all passwords.
Note 4: Do not use the PW_ON connector to clear CMOS.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
I2C to PCI-Express Slots
I2C to PCI-Express Slot
Jumper Settings
(JI2C1/JI2C2)
JI2C1/JI2C2 slots allows you to enable
the I2C bus to communicate with a
PCI-Express slot. For the jumpers to
work properly, please set both jumpers
to the same setting. If enabled, both
jumpers must be enabled. If disabled,
both jumpers must be disabled. See
the table on the right for jumper
settings.
Jumper Setting Definition
Closed
Open
Enabled
Disabled
BMC Jumper
BMC Jumper Enable (JPB1)
Jumper Settings
JPB1 is used to enable or disable
theBMC (Baseboard Management
Control) Chip and the onboard IPMI
connection.This jumper is used
together with the IPMI settings in the
BIOS. The default position is on pins
1 and 2 to Enable BMC. See the table
on the right for jumper settings.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Enabled (default)
Disabled
VGA Enable/Disable
VGA Enable/Disable
Jumper Settings (JPG1)
JPG1 allows you to enable or disable
the VGA port. The default position is on
pins 1 and 2 to enable VGA. See the
table on the right for jumper settings.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Enabled
Disabled
LAN Enable/Disable
LAN Jumper Settings
(JPL1)
Change the setting of jumper JPL1
to enable or disable the LAN1/2/3/4
Ethernet ports. See the table on the
right for jumper settings. The default
setting is enabled.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Enabled
Disabled
InfiniBand Port Enable/Disable
InfiniBand Port
Jumper Enable (JIB1)
Jumper Settings
JIB1 enables or disables the InfiniBand
port on H8DCT-HIBQF serverboard.
The default position is on pins 1 and 2
to enable the port. See the table below
for jumper settings.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Enabled
Disabled
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Watch Dog Enable/Disable
Watch Dog
Jumper Settings (JWD1)
JWD1 enables the Watch Dog function,
a system monitor that takes action
when a software application freezes
the system. Jumping pins 1-2 will have
WD reboot the system if a program
freezes. Jumping pins 2-3 will generate
a non-maskable interrupt for the
program that has frozen. See the table
on the right for jumper settings. Watch
Dog must also be enabled in BIOS.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Open
Reset
NMI
Disabled
Note: When Watch Dog is enabled, the user must write
their own application software to disable the Watch Dog
Timer.
2-10 Onboard Indicators
GLAN LED
LAN1/LAN2/LAN3/LAN4 LEDs
Activity
LED
Link Speed
LED
The Ethernet ports (located beside the
KVM port) have two LEDs. On each Gb
LAN port, one LED blinks to indicate
activity while the other may be green,
amber or off to indicate the speed of
the connection. See the table on the
right for the functions associated with
the connection speed LED.
GLAN Activity Indicator
(Right) LED Settings
Color
Off
Status
Definition
No Connections
Yellow
Flashing
Active
LAN Connection Speed
Indicator (Left) LED Settings
LED Color Definition
Off
10 MHz
100 MHz
1 GHz
Green
Amber
Power LED
Power LED
(DP2)
DP2 is an Onboard Power LED.
When this LED is lit, it means power
is present on the serverboard. Be
sure to turn off the system and unplug
the power cord(s) before removing or
installing components.
State
On
System Status
Standby power present
on motherboard
Off
No power connected
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
IPMI LAN
Dedicated IPMI LAN LEDs
Link LED
Activity LED
A dedicated IPMI LAN is also included
on the IPMI LAN port mounted on the
serverboard. The amber LED on the
right indicates activity, while the green
IPMI LAN
Link/Speed LED (Left)
& Activity LED (Right)
LED on the left indicates the speed of
the connection. See the table at right
for more information.
Color
Off
Status
Off
Definition
No Connection
100 Mb/s
Green:
Solid
Link/
Speed
(Left)
Amber
Blinking
Activity
(Right)
Active
InfiniBand LED Indicators
InfiniBand LED (LE2)
Activity LED
Two InfiniBand LED indicators
(LE2/LE3) are located near the
InfiniBand port of the H8DCT-HIBQF
serverboard. The green LED (LE2)
is the InfiniBand link LED while the
yellow LED (LE3) indicates activity.
Refer to the tables at the right for
details.
Color
Green
Off
Status
Solid
Off
Definition
InfiniBand Connected
No Connection
InfiniBand LED (LE3)
Activity LED
Color
Status
Solid
Dim
Definition
Yellow
Yellow
InfiniBand Active
InfiniBand Connected,
Activity Idle
Off
Off
No Connection
IPMI LED
IPMI LED (DP1)
The serverboard contains an IPMI LED
(DP1) located near the corner above
the PCI-E slots. When this LED is lit,
it means a connection is active for the
built-in IPMI on the serverboard.
State
System Status
Active connection
No connection
On
Off
Note: This LED is not installed on non-
IPMI boards.
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
UID LED (LE1)
A rear UID LED Indicator, located
at LE1, works in conjunction with
the rear UID switch to provide easy
identification for a unit that might be in
need of service. Refer to Page 2-12 for
further UID details.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-11 Enabling SATA RAID
Now that the hardware is set up, you must install the operating system and the
SATA RAID drivers, if you wish to use RAID with your SATA drives. The installation
procedure differs depending on whether you wish to have the operating system
installed on a RAID array or on a separate non-RAID drive. See the instructions
below for details.
Serial ATA (SATA)
Serial ATA (SATA) is a physical storage interface that employs a single cable with a
minimum of four wires to create a point-to-point connection between devices. This
connection is a serial link that supports a SATA transfer rate from 150 MBps. The
serial cables used in SATA are thinner than the traditional cables used in Parallel
ATA (PATA) and can extend up to one meter in length, compared to only 40 cm for
PATA cables. Overall, SATA provides better functionality than PATA.
Installing the OS/SATA Driver
Before installing the OS (operating system) and SATA RAID driver, you must decide
if you wish to have the operating system installed as part of a bootable RAID array
or installed to a separate non-RAID hard drive. If on a separate drive, you may
install the driver either during or after the OS installation. If you wish to have the
OS on a SATA RAID array, you must follow the procedure below and install the
driver during the OS installation.
Building a Driver Diskette
You must first build a driver diskette from Supermicro drivers for your system.
on a computer that is already running and with the OS installed.)
Building a Driver Diskette
1. Install your system drives from the FTP website. A display as shown in Figure
2-7 will appear.
2. Click on the icon labeled “Build Driver Diskettes and Manuals” and follow the
instructions to create a floppy disk with the drivers on it.
3. Once it’s been created, remove the floppy and insert the installation CD for
the Windows Operating System you wish to install into the CD-ROM drive of
the new system you are about to configure.
Note: You need to have an external USB floppy when building the driver diskette.
Window’s Vista, Windows 2008 or later Windows OS systems can use a USB stick
instead of a floppy.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Enabling SATA RAID in the BIOS
Before installing the Windows operating system, you must change some settings
in the BIOS. Boot up the system and hit the <Delete> key to enter the BIOS Setup
Utlility. After the setup utility loads,
1. Use the arrow keys to move to the "Exit" menu. Scroll down using the arrow
keys to "Load Optimal Defaults" and press <Enter>. Select "OK" to confirm,
then <Enter> to load the default settings.
2. Use the arrow keys to move to the "Advanced" menu, then scroll down to
"IDE configuration". On this submenu, scroll down to "OnChip SATA Type"
and choose the "RAID" option (Figure 2-4). “RAID Codebase” submenu
appears. This setting allows you to select the codebase for your RAID setup.
Options are either Adaptec or DotHill.
Figure 2-4. BIOS Setup Screen
3. Press the <Esc> key twice and scroll to the "Exit" menu. Select "Save
Changes and Exit" and press <Enter>, then press <Enter> again to verify.
4. After exiting the BIOS Setup Utility, the system reboots. When prompted
during the startup, to use the DotHilll RAID Utility program press the
<CTRL+R> key (Figure 2-5), or to use the Adaptec RAID Utility program
press the <CTRL+A> key (Figure 2-6).
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 2-5. DotHill RAID Utility Program Screen
Figure 2-6.Adaptec RAID Utility Program Screen
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Using the DotHill and Adaptec RAID Utility
The RAID Utility program allows you to define the drives you want to include in the
RAID array and the mode and type of RAID.
Installing the RAID Driver During OS Installation
You may also use the procedure below to install the RAID driver during the Windows
OS installation:
1. With the Windows OS installation CD-ROM in the CD drive, restart the
system.
2. Press <Enter> again to continue with the Windows setup.
3. When you see the prompt, hit the <F6> key to enter Windows setup.
4. Eventually a blue screen will appear with a message that begins “Windows
could not determine the type of one or more storage devices . . .” When you
see the screen, hit the <S> key to “Specify Additional Device”, then insert the
driver diskette you just created into the floppy drive.
5. Highlight “Manufuacturer Supplied Hardware Support Disk” and hit the
<Enter> key.
6. Highlight the first “Adaptec RAID” driver shown and press the <Enter> key to
install it.
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
2-12 Installing Drivers
The Supermicro Website contains drivers and utilities for your system at ftp://ftp.
supermicro.com, some of which must be installed, such as the chipset driver. After
downloading and installing the drivers and utilities, the display shown in Figure 2-7
should appear.
Click the icons showing a hand writing on paper to view the readme files for each
item. Click the computer icons to the right of these items to install each item (from
top to the bottom) one at a time. After installing each item, you should reboot the
system before moving on to the next item on the list. The bottom icon with a CD
on it allows you to view the entire contents of the utilities.
Figure 2-7. Driver/Tool Installation Display Screen
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Supero Doctor III
The SuperDoctor® III program is a Web base management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management is called SD III Client. The SuperDoctor III program included on the
CD-ROM that came with your motherboard allows you to monitor the environment
and operations of your system. SuperDoctor III displays crucial system information
such as CPU temperature, system voltages and fan status. See the Figure below
for a display of the SuperDoctor III interface.
Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor is first installed, it adopts the temperature threshold
settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor, as the SuperDoctor settings override the BIOS
settings. To set the BIOS temperature threshold settings again, you would first need
to uninstall SuperDoctor.
Figure 2-8. Supero Doctor III Interface Display Screen (Health Information)
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Figure 2-9. Supero Doctor III Interface Display Screen (Remote Control)
Note: The SuperDoctor III program and User’s Manual can be downloaded from the
Supermicro web site at http://www.supermicro.com/products/accessories/software/
SuperDoctorIII.cfm.For Linux, we recommend that you use the SuperoDoctor II
application instead.
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-13 Serverboard Battery
Caution: There is a danger of explosion if the onboard battery is installed upside
down, which will reverse its polarites (see Figure 2-10). This battery must be replaced
only with the same or an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the manufacturer's instructions.
Figure 2-10. Installing the Onboard Battery
OR
Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1 Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any
hardware components.
Before Power On
1. Check that the onboard power LED is lit (DP2 on the motherboard).
2. Make sure that the power connector is connected to your power supply.
3. Make sure that no short circuits exist between the motherboard and chassis.
4. Disconnect all cables from the motherboard, including those for the keyboard
and mouse.
5. Remove all add-on cards.
6. Install a CPU and heatsink (making sure it is fully seated) and connect the
internal (chassis) speaker and the power LED to the motherboard. Check all
jumper settings as well.
7. Use the correct type of onboard CMOS battery (CR2032) as recommended
by the manufacturer. To avoid possible explosion, do not install the CMOS
battery upside down.
No Power
1. Make sure that no short circuits exist between the motherboard and the
chassis.
2. Verify that all jumpers are set to their default positions.
3. Check that the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to verify that it still
supplies ~3VDC. If it does not, replace it with a new one.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
No Video
1. If the power is on but you have no video, remove all the add-on cards and
cables.
2. Use the speaker to determine if any beep codes exist. Refer to Appendix A
for details on beep codes.
Note: If you are a system integrator, VAR or OEM, a POST diagnostics card is
recommended. For I/O port 80h codes, refer to App. B.
Memory Errors
1. Make sure that the DIMM modules are properly and fully installed.
2. You should be using proper ECC DDR-3 memory (see next page). Also, it is
recommended that you use the same memory type and speed for all DIMMs
in the system. See Section 2-5 for memory details.
3. Check for bad DIMM modules or slots by swapping modules between slots
and noting the results.
4. Check the power supply voltage 115V/230V switch.
Losing the System’s Setup Configuration
1. Make sure that you are using a high quality power supply. A poor quality
power supply may cause the system to lose the CMOS setup information.
Refer to Section 1-6 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still
supplies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the setup configuration problem, contact your
vendor for repairs.
3-2 Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, note
that as a motherboard manufacturer, we do not sell directly to end-users, so it is
best to first check with your distributor or reseller for troubleshooting services. They
should know of any possible problem(s) with the specific system configuration that
was sold to you.
1. Please review the ‘Troubleshooting Procedures’ and 'Frequently Asked
Questions' (FAQs) sections in this chapter or see the FAQs on our web site
before contacting Technical Support.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
2. BIOS upgrades can be downloaded from our web site.
Note: Not all BIOS can be flashed depending on the modifications to the boot
block code.
3. If you still cannot resolve the problem, include the following information when
contacting us for technical support:
•
•
Serverboard model and PCB revision number
BIOS release date/version (this can be seen on the initial display when your
system first boots up)
•
System configuration
An example of a Technical Support form is posted on our web site.
Distributors: For immediate assistance, please have your account number ready
when contacting our technical support department by e-mail.
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The H8DCT-HLN4F/HIBQF serverboard supports up to a maximum
of up to 192 GB of ECC RDIMM, DDR3-1600/1333/1066 MHz speed,
1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size SDRAM memory in twelve (12)
slots. See Section 2-4 for details on installing memory.
Question: How do I update my BIOS?
Answer: It is recommended that you not upgrade your BIOS if you are not
experiencing problems with your system. Updated BIOS files are located on our
web site. Please check our BIOS warning message and the information on how to
update your BIOS on our web site. Also, check the current BIOS revision and make
sure it is newer than your current BIOS before downloading.
Select your motherboard model on the web page and download the corresponding
BIOS file to your computer. Unzip the BIOS update file, in which you will find the
readme.txt (flash instructions), the afudos.exe (BIOS flash utility) and the BIOS
image (xxx.rom) files. Copy these files to a bootable floppy disk, insert the disk
into drive A and reboot the system. At the DOS prompt after rebooting, enter the
command "flash" (without quotation marks) then type in the BIOS file that you want
to update with (xxxx.rom).
Question: What's on the CD that came with my motherboard?
Answer: The supplied compact disc has quite a few drivers and programs that will
greatly enhance your system. We recommend that you review the CD and install the
applications you need. Applications on the CD include chipset drivers for Windows
and security and audio drivers.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Question: Why can't I turn off the power using the momentary power on/off
switch?
Answer: The instant power off function is controlled in BIOS by the Power Button
Mode setting. When the On/Off feature is enabled, the motherboard will have instant
off capabilities as long as the BIOS has control of the system. When the Standby
or Suspend feature is enabled or when the BIOS is not in control such as during
memory count (the first screen that appears when the system is turned on), the
momentary on/off switch must be held for more than four seconds to shut down the
system. This feature is required to implement the ACPI features on the motherboard.
3-4 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning to
the manufacturer, the RMA number should be prominently displayed on the outside
of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling
charges will be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online (http://www.super-
micro.com/support/rma/).
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product problems.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMIBIOS™ Setup utility for the H8DCT-HLN4F/HIBQF
serverboard. The 16 Mb AMI BIOS® is stored in a flash chip and can be easily
upgraded using a floppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of our web site for any changes to BIOS that may not be reflected
in this manual.
Starting the Setup Utility
To enter the BIOS Setup Utility, hit the <Delete> key while the system is booting-up.
(In most cases, the <Delete> key is used to invoke the BIOS setup screen. There
are a few cases when other keys are used, such as <F1>, <F2>, etc.) Each main
BIOS menu option is described in this manual.
The Main BIOS screen has two main frames. The left frame displays all the options
that can be configured. “Grayed-out” options cannot be configured. The right frame
displays the key legend. Above the key legend is an area reserved for a text
message. When an option is selected in the left frame, it is highlighted in white. Often
a text message will accompany it. (Note that BIOS has default text messages built
in. We retain the option to include, omit, or change any of these text messages.)
Settings printed in Bold are the default values.
A " "indicates a submenu. Highlighting such an item and pressing the <Enter>
key will open the list of settings within that submenu.
The BIOS setup utility uses a key-based navigation system called hot keys. Most
of these hot keys (<F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used
at any time during the setup navigation process.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
4-2 Main Menu
When you first enter AMI BIOS Setup Utility, you will see the Main Menu screen.
You can always return to the Main Menu by selecting the Main tab on the top of
the screen with the arrow keys.
The Main Menu screen provides you with a system overview, which includes the
version, built date and ID of the AMIBIOS, the type, speed and number of the
processors in the system and the amount of memory installed in the system.
System Time/System Date
You can edit this field to change the system time and date. Highlight System Time
or System Date using the <Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move between fields. The date must
be entered in DAY/MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Please note that time is in a 24-hour format. For example, 5:30 A.M. appears as
05:30:00 and 5:30 P.M. as 17:30:00.
4-3 Advanced Settings Menu
Boot Feature
Quick Boot
If Enabled, this option will skip certain tests during POST to reduce the time
needed for the system to boot up. The options are Enabled and Disabled.
Quiet Boot
If Disabled, normal POST messages will be displayed on boot-up. If Enabled,
this display the OEM logo instead of POST messages.
Add On ROM Display Mode
This option sets the display mode for Option ROM. The options are Force BIOS
or Keep Current.
Bootup Num Lock
This option selects the power-on state for the NUM lock to either On or Off.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Wait for F1 if Error
This setting controls the system response when an error is detected during the
boot sequence. When enabled, BIOS will stop the boot sequence when an error
is detected, at which point you will need to press the F1 button to re-enter the
BIOS setup menu. The options are Enabled and Disabled.
Hit 'DEL' Message Display
Use this option to Enable or Disable the "Press DEL to run setup" message in
POST.
Interrupt 19 Capture
Select Enabled to allow ROMs to trap Interrupt 19. The options are Enabled
and Disabled.
Watch Dog Function
Allows system to restart when system is inactive more than 5-minutes. The
options are Enabled and Disabled.
Power Button Function
This sets the function of the power button when you turn off the system. Options
include 4-second Overide and Instant Off.
Restore on AC Power Loss
This sets the action that occurs when an AC power loss occurs. Options include
Power Off, Power On and Last State.
Resume on RTC Alarm
This setting allows you to enable or disable RTC to generate a wake event for
S4/S5 or Legacy Soft Off. Options are Enabled and Disabled.
Processor and Clock Options
CPU Configuration
This displays static information on the Module Version, Physical Count and
Logical Count for the system's processor(s) and clock.
CPU Information
The information for the installed processor includes Revision, Cache L1/L2/L3,
Speed, NB CLK, Able to Change Frequency and uCode Patch Level.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
GART Error Reporting
This option should remain disabled for normal operation. The driver developer
may enable this option for testing purposes. Options are Enabled or Disabled.
Microcode Update
This setting Enables or Disables microcode updating.
Secure Virtual Machine Mode
This setting is used to Enable or Disable SVM.
Power Now
This setting is used to Enable or Disable the AMD Power Now feature.
Power Cap
This option can decide the highest P-state in the OS. Options include P-state
0 through P-state 4.
CPU Down Core Mode
This option sets down core support for the CPU. Options include Disabled, 1
Core through n Cores in odd numbered increments. The value n is depend on
the core per CPU node.
Advanced Chipset Control
NorthBridge Configuration
Memory Configuration
Bank Interleaving
Select Auto to automatically enable a bank-interleaving memory scheme
when this function is supported by the processor. The options are Auto
and Disabled.
Node Interleaving
This option enables node memory interleaving. Options include Auto or
Disabled.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Channel Interleaving
This option enables channel memory interleaving. Options include Auto
or Disabled.
CS Sparing
This setting will reserve a spare memory rank in each node when enabled.
Options are Enabled and Disabled.
Bank Swizzle Mode
This setting Enables or Disables the bank swizzle mode.
ECC Configuration
ECC Mode
This submenu affects the DRAM scrub rate based on its setting. Options
include Disabled, Basic, Good, Super, Max and User. Selecting User
activates the other options for user setting.
DRAM ECC Enable
This setting allows hardware to report and correct memory errors
automatically, maintaining system integrity. Options are Enabled or
Disabled. This is option is only active if ECC Mode above is set to User.
DRAM Timing Configuration
DRAM Timing Config
This option allows you to set the DRAM timing configuration for the system.
Options include Auto or Manual.
Memory Clock Speed
This options sets the memory clock speed. Options include 200 Mhz,
266 Mhz, 333 Mhz, 400 Mhz, 533 Mhz, 667 Mhz, 800 Mhz and 933 Mhz.
HT Speed Support
Use this option to select the HT Link Frequency. Options include HT1 or
Auto. Note that a Cold Reset is needed after changing this option's setting.
IOMMU
This setting is used to enable or disable or set the GART size in systems
without AGP. Options include Enabled and Disabled.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
SouthBridge Configuration
OHCI/EHCI HC Device Functions
These settings allow you to either Enable or Disable functions for OHCI or EHCI
bus devices.
USB 2.0 Controller Mode
Use this setting to configure the USB 2.0 Controller in either Hi-Speed (480
Mps) or Full Speed (12 Mps) mode. Options include Enabled (Hi-Speed Mode)
or Disabled (Full Speed Mode).
Legacy USB Support
Select "Enabled" to enable the support for USB Legacy. Disable Legacy support if
there are no USB devices installed in the system. "Auto" disabled Legacy support
if no USB devices are connected. The options are Disabled, Enabled and Auto.
IDE Configuration
OnChip SATA Channel
This setting allows you to Enable or Disable the OnChip SATA channel.
OnChip SATA Type
Use this setting to set the OnChip SATA type. Options include
Native IDE, RAID, AMD_AHCI and Legacy IDE.
RAID Codebase
This submenu appears when you choose "RAID" from the "OnChip SATA
Type" setting above. This setting allows you to select the codebase for using
your RAID setup. Options are either Adaptec or DotHill.
SATA IDE Combined Mode
This setting allows you to Enable or Disable the SATA IDE combined mode.
PATA Channel Configuration
This allows you to set PATA channel configuration. Options include SATA as
Primary or SATA as secondary.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Primary/Secondary/Third/Fourth IDE Master/Slave
LBA/Large Mode
LBA (Logical Block Addressing) is a method of addressing data on a disk
drive. The options are Disabled and Auto.
Block (Multi-Sector Transfer)
Block mode boosts IDE drive performance by increasing the amount of data
transferred. Only 512 bytes of data can be transferred per interrupt if block
mode is not used. Block mode allows transfers of up to 64 KB per interrupt.
Select "Disabled" to allow the data to be transferred from and to the device
one sector at a time. Select "Auto" to allows the data transfer from and to the
device occur multiple sectors at a time if the device supports it. The options
are Auto and Disabled.
PIO Mode
PIO (Programmable I/O) mode programs timing cycles between the IDE drive
and the programmable IDE controller. As the PIO mode increases, the cycle
time decreases.
The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow BIOS to auto
detect the PIO mode. Use this value if the IDE disk drive support cannot be
determined. Select 0 to allow BIOS to use PIO mode 0, which has a data
transfer rate of 3.3 MBs. Select 1 to allow BIOS to use PIO mode 1, which has
a data transfer rate of 5.2 MBs. Select 2 to allow BIOS to use PIO mode 2,
which has a data transfer rate of 8.3 MBs. Select 3 to allow BIOS to use PIO
mode 3, which has a data transfer rate of 11.1 MBs. Select 4 to allow BIOS
to use PIO mode 4, which has a data transfer rate of 16.6 MBs. This setting
generally works with all hard disk drives manufactured after 1999. For other
disk drives, such as IDE CD-ROM drives, check the specifications of the drive.
DMA Mode
Selects the DMA Mode. Options are Auto, SWDMA0, SWDMA1, SWDMA2,
MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3,
UDMA4 and UDMA5. (SWDMA=Single Word DMA, MWDMA=Multi Word
DMA, UDMA=UltraDMA.)
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
S.M.A.R.T.
Self-Monitoring Analysis and Reporting Technology (SMART) can help
predict impending drive failures. Select "Auto" to allow BIOS to auto detect
hard disk drive support. Select "Disabled" to prevent AMI BIOS from using
the S.M.A.R.T. Select "Enabled" to allow AMI BIOS to use the S.M.A.R.T.
to support hard drive disk. The options are Disabled, Enabled, and Auto.
32-Bit Data Transfer
Select "Enabled" to activate the function of 32-Bit data transfer. Select
"Disabled" to deactivate the function. The options are Enabled and Disabled.
IDE Detect Timeout (Sec)
Use the +/- keys to adjust and select the time out for detecting ATA/ATAPI
devices. The default value is 35.
PCI/PnP Configuration
Clear NVRAM
Select Yes to clear NVRAM during boot-up. The options are Yes and No.
Plug & Play O/S
Select Yes to allow the OS to configure Plug & Play devices. (This is not required
for system boot if your system has an OS that supports Plug & Play.) Select No
to allow AMIBIOS to configure all devices in the system.
PCI Latency Timer
This option sets the latency of all PCI devices on the PCI bus. Select a value
to set the PCI latency in PCI clock cycles. Options are 32, 64, 96, 128, 160,
192, 224 and 248.
PCI IDE Busmaster
Use this setting to Enable or Disable BIOS enabled uses of PCI Busmastering
for reading or writing to IDE drives.
ROM Scan Ordering
This setting determines which kind of option ROM activates prior to another.
Options include Onboard First and Addon First.
PCIe Slot 1 Riser
This setting allows you to optimize your PCIe Slot 1 riser to either 1x16, 2x8
or Auto.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
PCIe x16 Slot 1
These settings Enable or Disable the specified PCIe slot in your system.
PCIe x8 Slot 2
These settings Enable or Disable the specified PCIe slot in your system.
Onboard LAN Option ROM Select
This setting allows you to select the onboard LAN option ROM for iSCSI or PXE.
Note: You must enable ONLY LAN1 when the iSCSI support option is specified.
Load Onboard LAN 1 Option ROM
This option allows you to enable or disable the onboard LAN 1 option ROM.
Load Onboard LAN 2 Option ROM
This option allows you to enable or disable the onboard LAN 2 option ROM.
Boots Graphic Adapter Priority
This option specifies the priority for booting the graphic adapter for Onboard
VGA or Offboard VGA.
SuperIO Device Configuration
Serial 1 Address
This option specifies the base I/O port address and Interrupt Request address
of serial port 1. Select "Disabled" to prevent the serial port from accessing any
system resources. When this option is set to Disabled, the serial port physically
becomes unavailable. Select "3F8/IRQ4" to allow the serial port to use 3F8 as its
I/O port address and IRQ 4 for the interrupt address. Options include Disabled,
3F8/IRQ4, 3E8/IRQ4 and 2E8/IRQ3
Serial 2 Address
This option specifies the base I/O port address and Interrupt Request address
of serial port 2. Select "Disabled" to prevent the serial port from accessing any
system resources. When this option is set to "Disabled", the serial port physically
becomes unavailable. Select "2F8/IRQ3" to allow the serial port to use 2F8 as its
I/O port address and IRQ 3 for the interrupt address. Options include Disabled,
2F8/IRQ3, 3E8/IRQ4 and 2F8/IRQ3.
Serial Port 2 Attribute
This option allows you to set COM2 as a normal serial port or as virtual COM
for SOL. Options are SOL or COM.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Remote Access Configuration
Remote Access
Use this option to Enable or Disable Remote Access in your system. If enabled,
the settings below will appear.
Serial Port Number
Use this setting to select the serial port for console redirection. Options include
COM1, COM2*. The displayed base address and IRQ for the serial port changes
to reflect the selection you make.
Note: Make sure the selected port is enabled.
Serial Port Mode
Selects the serial port settings to use. Options are (115200 8, n, 1), (57600 8,
n, 1), (38400 8, n, 1), (19200 8, n, 1) and (09600 8, n, 1).
Flow Control
Selects the flow control to be used for console redirection. Options are None,
Hardware and Software.
Redirection After BIOS POST
Options are Disable (no redirection after BIOS POST), Boot Loader (redirection
during POST and during boot loader) and Always (redirection always active).
Note that some OS's may not work with this set to Always.
Terminal Type
Selects the type of the target terminal. Options are ANSI, VT100 and VT-UTF8.
VT-UTF8 Combo Key Support
Allows you to Enable or Disable VT-UTF8 combination key support for ANSI/
VT100 terminals.
Sredir Memory Display Delay
Use this setting to set the delay in seconds to display memory information.
Options are No Delay, 1 sec, 2 secs and 4 secs.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Hardware Health Configuration
CPU Overheat Alarm
This setting allows you to specify the type of alarm for CPU overheating. Options
include The Early Alarm and The Default Alarm.
Fan Speed Control Modes
This feature allows the user to determine how the system will control the speed
of the onboard fans. The options are Full Speed/FS (Max Cooling), Performance/
PF (Better Cooling), Balanced/BL (Balance between performance and energy
saving), Energy Saving/ES (Lower Power and Noise).
Other items in the submenu are systems monitor displays for the following
information:
CPU 1 Temperature, CPU 2 Temperature, System Temperature, Fan 1-2
Reading, CPU 1 VCore, CPU 2 VCore, CPU 1 Mem VTT, CPU 2 Mem VTT,
CPU 1 Mem, CPU 2 Mem, 1.1V, 1.8V, 5V, +12V, 3.3 Vcc, 3.3 VSB, VBAT
and HT Voltage.
CPU Temperature Display (CTD)
CPU Temperature descriptions are defined as:
Low [Tctl Value = Lowest Value, Tctl Value = -45]
Medium [Tctl Value = -46, Tctl Value = 60]
High [Tctl Value = -61 and Above]
Note: Only CPU temperature (Low, Medium, High) and system temperature (RT1)
are required to be displayed in BIOS and in-system monitoring software. Other
Serverboard components such as memory, chipset, SAS and 10Gb controllers,
and others are not requried to display temperatures. For debugging and testing
purposes, BIOS and system monitoring software can show motherboard
components’ temperatures (such as memory, chipset, SAS and 10Gb controllers).
However for SMCI standard release version BIOS and system monitoring software,
motherboard components’ temperatures are NOT required to be displayed.
CPU Overheating Alarm (COA)
CPU Overheating Alarm (COA) has “Early Alarm” and “Default Alarm” (default)
options in the BIOS, and is required to be implemented in all fan speed control
modes.
The Early Alarm is enabled when the Tctl value = 65, and is disabled when the Tctl
value drops from 65 to 62.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
The Default Alarm (default setting) is enabled when the Tctl value = 70, and is
disabled when the Tctl value drops from 70 to 67.
When COA (either Early or Default Alarm) is enabled, the following actions are
required to be executed:
•
•
•
•
System overheating LED is required to be ON and to solid red.
Onboard buzzer or speaker is required to be ON and to be a continuous sound.
All system fans are required to be operated at full speed.
System monitoring software (such as Super Doctor and IPMI if available) is
required to report and record CPU overheating events in the event logs.
When COA (either Early or Default Alarm) is disabled, the following actions are
required to be executed:
•
•
•
System overheating LED is required to be OFF.
Onboard buzzer or speaker is required to be OFF.
All system fans are required to be returned to a normal, non-CPU-overheating
LFSC condition.
Condition
When a CPU is overheating
On and Solid Red
Front Panel Overheating LED
Onboard Buzzer or Speaker
System Fan Speed Controls
BMC
On and Continuous Sound
Full Speed
Report PROCHOT
Record PROCHOT
Report PROCHOT
Record PROCHOT
BMC Event Log
Super Doctor
Super Doctor Event Log
ACPI Configuration
ACPI Aware O/S
This setting Enables or Disables ACPI support for the system's operating system.
Options include Yes (enabled) or No (disabled).
ACPI APIC Support
Determines whether to include the ACPI APIC table pointer in the RSDT pointer
list. The available options are Enabled and Disabled.
Headless Mode
Use this setting to Enable or Disable headless operation mode through ACPI.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
ACPI Version Features
Use this setting the determine which ACPI version to use. Options are ACPI
v1.0, ACPI v2.0 and ACPI v3.0.
NUMA Support
This setting allows you to enable or disable the building of an ACPI SRAT table.
WHEA Support
This setting allows you to enable or disable Windows Hardware ErrorArchitecture.
IPMI Configuration
This menu shows static information about the IPMI firmware revision and status of
the BMC, as well as options for IPMI configuration.
View BMC System Event Log
Pressing the Enter key will open the following settings. Use the "+" and "-" keys
to navigate through the system event log.
Clear BMC System Event Log
Selecting this and pressing the Enter key will clear the BMC system event log.
Set LAN Configuration
Use the "+" and "-" keys to choose the desired channel number. This displays
Channel Number and Channel Number Status information.
This menu contains options for inputing settings for the SET LAN Configuration
Command. See IPMI 1.5 Specification, table 11.1 for details. Use the "+" and
"-" keys to choose the desired channel number.
Note: Each question in this group may take a considerable amount of time.
IP Address Source
Select the source of this machine's IP address. If Static is selected, you will
need to know and enter manually the IP address of this machine below.
If DHCP is selected, the BIOS will search for a DHCP (Dynamic Host
Configuration Protocol) server in the network it is attached to, and request
the next available IP address. The options are DHCP and Static.
The following items are assigned IP addresses automatically if DHCP is
selected under IP Address Source above:
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
IP Address
This submenu sets the IP address source as either Static or DHCP. Selecting
Static allows you to manually set the IP Address, Subnet Mask and Gateway
Address.
In the field provided here enter the IP address in the decimal form of xxx.xxx.
xxx.xxx with xxx having a value of less than 256 and in decimal form only The
IP address and current IP address in the BMC are shown.
Subnet Mask
In the field provided here enter the Subnet address in the decimal form of
xxx.xxx.xxx.xxx with xxx having a value of less than 256 and in decimal form
only. The current subnet address in the BMC is shown.
Gateway Address
In the field provided here enter the Gateway address in the decimal form of
xxx.xxx.xxx.xxx with xxx having a value of less than 256 and in decimal form
only. The current Gateway address in the BMC is shown.
MAC Address
In the field provided here enter the MAC address in the hex form of xx.xx.xx.xx.
xx.xx with xx in hex form only. The current MAC address in the BMC is shown.
Event Log Configuration
View Event Log
Pressing the Enter key will open the event log. Use the "" and "" keys to
navigate through the system event log.
Mark All Events as Read
Selecting this and pressing the Enter key marks all events as read in the event
log.
Clear Event Log
Selecting this and pressing the Enter key clears the system event log.
SR56x0 (RD890S) PCIE Error Log
This setting allows you set an error log ofr PCIE errors. Options include Yes
or No.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-3 Security Menu
AMI BIOS provides a Supervisor and a User password. If you use both passwords,
the Supervisor password must be set first.
Change Supervisor Password
Select this option and press <Enter> to access the sub menu, and then type in
the password.
Change User Password
Select this option and press <Enter> to access the sub menu, and then type in
the password.
Boot Sector Virus Protection
This option is near the bottom of the Security Setup screen. Select "Disabled" to
deactivate the Boot Sector Virus Protection. Select "Enabled" to enable boot sector
protection. When "Enabled", AMI BIOS displays a warning when any program (or
virus) issues a Disk Format command or attempts to write to the boot sector of the
hard disk drive. The options are Enabled and Disabled.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
4-4 Boot Menu
The Boot Menu is accessible only when the "Load Onboard LAN Option ROM"
setting (in the PCI/PnP Configuration menu) is enabled.
Boot Device Priority
This feature allows you to prioritize the boot sequence from the list of available
devices. A device that is in parenthesis has been disabled in the corresponding
type menu.
Removable Drives
This feature allows you to specify the boot sequence from the list of available CD/
DVD drives. A device that is in parenthesis has been disabled in the corresponding
type menu.
Hard Disk Drives
This feature allows you to specify the boot sequence from the list of available hard
disk drives. A device that is in parenthesis has been disabled in the corresponding
type menu.
CD/DVD Drives
This feature allows you to specify the boot sequence from the list of available CD/
DVD drives. A device that is in parenthesis has been disabled in the corresponding
type menu.
USB Drives
This feature allows you to specify the boot sequence from the list of available USB
drives. A device that is in parenthesis has been disabled in the corresponding type
menu.
Network Drives
This feature allows you to specify the boot sequence from the list of available
Network drives. A device that is in parenthesis has been disabled in the
corresponding type menu.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Retry Boot Devices
This option allows you to retry boot devices. Options include Enabled and Disabled.
4-5 Exit Menu
Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup
screen.
Save Changes and Exit
When you have completed the system configuration changes, select this option
to leave BIOS Setup and reboot the computer, so the new system configuration
parameters can take effect. Select Save Changes and Exit from the Exit menu and
press <Enter>.
Discard Changes and Exit
Select this option to quit BIOS Setup without making any permanent changes to the
system configuration and reboot the computer. Select Discard Changes and Exit
from the Exit menu and press <Enter>.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to AMI
BIOS Utility Program.
Load Optimal Defaults
To set this feature, select Load Optimal Defaults from the Exit menu and press
<Enter>. Then Select "OK" to allow BIOS to automatically load the Optimal Defaults
as the BIOS Settings. The Optimal settings are designed for maximum system
performance, but may not work best for all computer applications.
Load Fail-Safe Defaults
To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but not
maximum performance.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time
the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the
boot-up process. The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up
procedure. If a fatal error occurs, you should consult with your system manufacturer
for possible repairs.
These fatal errors are usually communicated through a series of audible beeps. The
numbers on the fatal error list (on the following page) correspond to the number
of beeps for the corresponding error. All errors listed, with the exception of Beep
Code 8, are fatal errors.
A-1 AMIBIOS Error Beep Codes
Beep Code
1 beep
Error Message
Refresh
Description
Circuits have been reset (Ready to power up)
No memory detected in system
Video adapter disabled or missing
5 shorts, 1 long beep
1 long, 8 short
Memory error
Video error
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Notes
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Checkpoint Codes
Appendix B
BIOS POST Checkpoint Codes
When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O
port 0080h. If the computer cannot complete the boot process, diagnostic equipment
can be attached to the computer to read I/O port 0080h.
B-1 Uncompressed Initialization Codes
The uncompressed initialization checkpoint codes are listed in order of execution:
Checkpoint Code Description
D0h
The NMI is disabled. Power on delay is starting. Next, the initialization code checksum will be
verified.
D1h
Initializing the DMA controller, performing the keyboard controller BAT test, starting memory
refresh and entering 4 GB flat mode next.
D3h
D4h
D5h
Starting memory sizing next.
Returning to real mode. Executing any OEM patches and setting the Stack next.
Passing control to the uncompressed code in shadow RAM at E000:0000h. The initialization
code is copied to segment 0 and control will be transferred to segment 0.
D6h
Control is in segment 0. Next, checking if <Ctrl> <Home> was pressed and verifying the system
BIOS checksum. If either <Ctrl> <Home> was pressed or the system BIOS checksum is bad,
next will go to checkpoint code E0h. Otherwise, going to checkpoint code D7h.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
B-2 Bootblock Recovery Codes
The bootblock recovery checkpoint codes are listed in order of execution:
Checkpoint Code Description
E0h
The onboard floppy controller if available is initialized. Next, beginning the base 512 KB
memory test.
E1h
E2h
E6h
Edh
Eeh
Efh
Initializing the interrupt vector table next.
Initializing the DMA and Interrupt controllers next.
Enabling the floppy drive controller and Timer IRQs. Enabling internal cache memory.
Initializing the floppy drive.
Looking for a floppy diskette in drive A:. Reading the first sector of the diskette.
A read error occurred while reading the floppy drive in drive A:.
Next, searching for the AMIBOOT.ROM file in the root directory.
The AMIBOOT.ROM file is not in the root directory.
F0h
F1h
F2h
Next, reading and analyzing the floppy diskette FAT to find the clusters occupied by the
AMIBOOT.ROM file.
F3h
F4h
F5h
FBh
FCh
FDh
FFh
Next, reading the AMIBOOT.ROM file, cluster by cluster.
The AMIBOOT.ROM file is not the correct size.
Next, disabling internal cache memory.
Next, detecting the type of flash ROM.
Next, erasing the flash ROM.
Next, programming the flash ROM.
Flash ROM programming was successful. Next, restarting the system BIOS.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Checkpoint Codes
B-3 Uncompressed Initialization Codes
The following runtime checkpoint codes are listed in order of execution.
These codes are uncompressed in F0000h shadow RAM.
Checkpoint Code Description
03h
05h
06h
07h
08h
0Ah
The NMI is disabled. Next, checking for a soft reset or a power on condition.
The BIOS stack has been built. Next, disabling cache memory.
Uncompressing the POST code next.
Next, initializing the CPU and the CPU data area.
The CMOS checksum calculation is done next.
The CMOS checksum calculation is done. Initializing the CMOS status register for date and
time next.
0Bh
0Ch
0Eh
0Fh
10h
11h
The CMOS status register is initialized. Next, performing any required initialization before the
keyboard BAT command is issued.
The keyboard controller input buffer is free. Next, issuing the BAT command to the keyboard
controller.
The keyboard controller BAT command result has been verified. Next, performing any
necessary initialization after the keyboard controller BAT command test.
The initialization after the keyboard controller BAT command test is done. The keyboard
command byte is written next.
The keyboard controller command byte is written. Next, issuing the Pin 23 and 24 blocking and
unblocking command.
Next, checking if <End or <Ins> keys were pressed during power on. Initializing CMOS RAM
if the Initialize CMOS RAM in every boot AMIBIOS POST option was set in AMIBCP or the
<End> key was pressed.
12h
13h
14h
19h
1Ah
2Bh
Next, disabling DMA controllers 1 and 2 and interrupt controllers 1 and 2.
The video display has been disabled. Port B has been initialized. Next, initializing the chipset.
The 8254 timer test will begin next.
Next, programming the flash ROM.
The memory refresh line is toggling. Checking the 15 second on/off time next.
Passing control to the video ROM to perform any required configuration before the video ROM
test.
2Ch
2Dh
23h
All necessary processing before passing control to the video ROM is done. Looking for the
video ROM next and passing control to it.
The video ROM has returned control to BIOS POST. Performing any required processing after
the video ROM had control
Reading the 8042 input port and disabling the MEGAKEY Green PC feature next. Making the
BIOS code segment writable and performing any necessary configuration before initializing the
interrupt vectors.
24h
The configuration required before interrupt vector initialization has completed. Interrupt vector
initialization is about to begin.
25h
27h
28h
Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on.
Any initialization before setting video mode will be done next.
Initialization before setting the video mode is complete. Configuring the monochrome mode and
color mode settings next.
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Checkpoint Code Description
2Ah
Bus initialization system, static, output devices will be done next, if present. See the last page
for additional information.
2Eh
Completed post-video ROM test processing. If the EGA/VGA controller is not found, performing
the display memory read/write test next.
2Fh
30h
31h
The EGA/VGA controller was not found. The display memory read/write test is about to begin.
The display memory read/write test passed. Look for retrace checking next.
The display memory read/write test or retrace checking failed. Performing the alternate display
memory read/write test next.
32h
The alternate display memory read/write test passed. Looking for alternate display retrace
checking next.
34h
37h
38h
Video display checking is over. Setting the display mode next.
The display mode is set. Displaying the power on message next.
Initializing the bus input, IPL, general devices next, if present. See the last page of this chapter
for additional information.
39h
Displaying bus initialization error messages. See the last page of this chapter for additional
information.
3Ah
3Bh
40h
42h
43h
44h
The new cursor position has been read and saved. Displaying the Hit <DEL> message next.
The Hit <DEL> message is displayed. The protected mode memory test is about to start.
Preparing the descriptor tables next.
The descriptor tables are prepared. Entering protected mode for the memory test next.
Entered protected mode. Enabling interrupts for diagnostics mode next.
Interrupts enabled if the diagnostics switch is on. Initializing data to check memory wraparound
at 0:0 next.
45h
46h
47h
Data initialized. Checking for memory wraparound at 0:0 and finding the total system memory
size next.
The memory wraparound test is done. Memory size calculation has been done. Writing patterns
to test memory next.
The memory pattern has been written to extended memory. Writing patterns to the base 640
KB memory next.
48h
49h
4Bh
Patterns written in base memory. Determining the amount of memory below 1 MB next.
The amount of memory below 1 MB has been found and verified.
The amount of memory above 1 MB has been found and verified. Checking for a soft reset and
clearing the memory below 1 MB for the soft reset next. If this is a power on situation, going to
checkpoint 4Eh next.
4Ch
4Dh
4Eh
4Fh
50h
51h
The memory below 1 MB has been cleared via a soft reset. Clearing the memory above 1 MB
next.
The memory above 1 MB has been cleared via a soft reset. Saving the memory size next.
Going to checkpoint 52h next.
The memory test started, but not as the result of a soft reset. Displaying the first 64 KB memory
size next.
The memory size display has started. The display is updated during the memory test.
Performing the sequential and random memory test next.
The memory below 1 MB has been tested and initialized. Adjusting the displayed memory size
for relocation and shadowing next.
The memory size display was adjusted for relocation and shadowing.
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Checkpoint Codes
Checkpoint Code Description
52h
The memory above 1 MB has been tested and initialized. Saving the memory size information
next.
53h
54h
The memory size information and the CPU registers are saved. Entering real mode next.
Shutdown was successful. The CPU is in real mode. Disabling the Gate A20 line, parity, and
the NMI next.
57h
58h
59h
The A20 address line, parity, and the NMI are disabled. Adjusting the memory size depending
on relocation and shadowing next.
The memory size was adjusted for relocation and shadowing. Clearing the Hit <DEL> message
next.
The Hit <DEL> message is cleared. The <WAIT...> message is displayed. Starting the DMA
and interrupt controller test next.
60h
62h
The DMA page register test passed. Performing the DMA Controller 1 base register test next.
The DMA controller 1 base register test passed. Performing the DMA controller 2 base register
test next.
65h
66h
67h
7Fh
80h
The DMA controller 2 base register test passed. Programming DMA controllers 1 and 2 next.
Completed programming DMA controllers 1 and 2. Initializing the 8259 interrupt controller next.
Completed 8259 interrupt controller initialization.
Extended NMI source enabling is in progress.
The keyboard test has started. Clearing the output buffer and checking for stuck keys. Issuing
the keyboard reset command next.
81h
82h
83h
84h
85h
86h
87h
88h
89h
A keyboard reset error or stuck key was found. Issuing the keyboard controller interface test
command next.
The keyboard controller interface test completed. Writing the command byte and initializing the
circular buffer next.
The command byte was written and global data initialization has completed. Checking for a
locked key next.
Locked key checking is over. Checking for a memory size mismatch with CMOS RAM data
next.
The memory size check is done. Displaying a soft error and checking for a password or
bypassing WINBIOS Setup next.
The password was checked. Performing any required programming before WINBIOS Setup
next.
The programming before WINBIOS Setup has completed. Uncompressing the WINBIOS Setup
code and executing the AMIBIOS Setup or WINBIOS Setup utility next.
Returned from WINBIOS Setup and cleared the screen. Performing any necessary
programming after WINBIOS Setup next.
The programming after WINBIOS Setup has completed. Displaying the power on screen
message next.
8Ch
8Dh
8Fh
91h
95h
Programming the WINBIOS Setup options next.
The WINBIOS Setup options are programmed. Resetting the hard disk controller next.
The hard disk controller has been reset. Configuring the floppy drive controller next.
The floppy drive controller has been configured. Configuring the hard disk drive controller next.
Initializing the bus option ROMs from C800 next. See the last page of this chapter for additional
information.
96h
Initializing before passing control to the adaptor ROM at C800.
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
H8DCT-HLN4F/HIBQF SERVERBOARD USER'S MANUAL
Checkpoint Code Description
97h
98h
99h
Initialization before the C800 adaptor ROM gains control has completed. The adaptor ROM
check is next.
The adaptor ROM had control and has now returned control to BIOS POST. Performing any
required processing after the option ROM returned control.
Any initialization required after the option ROM test has completed. Configuring the timer data
area and printer base address next.
9Ah
9Bh
Set the timer and printer base addresses. Setting the RS-232 base address next.
Returned after setting the RS-232 base address. Performing any required initialization before
the Coprocessor test next.
9Ch
9Dh
9Eh
Required initialization before the Coprocessor test is over. Initializing the Coprocessor next.
Coprocessor initialized. Performing any required initialization after the Coprocessor test next.
Initialization after the Coprocessor test is complete. Checking the extended keyboard, keyboard
ID, and Num Lock key next. Issuing the keyboard ID command next.
A2h
A3h
A4h
A5h
Displaying any soft errors next.
The soft error display has completed. Setting the keyboard typematic rate next.
The keyboard typematic rate is set. Programming the memory wait states next.
Memory wait state programming is over. Clearing the screen and enabling parity and the NMI
next.
A7h
A8h
A9h
Aah
NMI and parity enabled. Performing any initialization required before passing control to the
adaptor ROM at E000 next.
Initialization before passing control to the adaptor ROM at E000h completed. Passing control to
the adaptor ROM at E000h next.
Returned from adaptor ROM at E000h control. Performing any initialization required after the
E000 option ROM had control next.
Initialization after E000 option ROM control has completed. Displaying the system configuration
next.
Abh
B0h
B1h
00h
Uncompressing the DMI data and executing DMI POST initialization next.
The system configuration is displayed.
Copying any code to specific areas.
Code copying to specific areas is done. Passing control to INT 19h boot loader next.
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|