SY-K7ADA V1.0
Motherboard
****************************************************
AMD® Athlon/Duron
Processor supported
ALI MAGIK1 AGP/PCI Motherboard
266/200 MHz Front Side Bus supported
ATX Form Factor
****************************************************
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SY-K7ADA V1.0
Table of Contents
CHAPTER 1 MOTHERBOARD DESCRIPTION................................1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
INTRODUCTION...............................................................1
KEY FEATURES................................................................1
ELECTROSTATIC DISCHARGE PRECAUTIONS..........4
SY-K7ADA V1.0 MOTHERBOARD LAYOUT................5
SY-K7ADA V1.0 MOTHERBOARD COMPONENTS .................6
MICROPROCESSOR.........................................................8
CHIPSET ............................................................................9
HARDWARE MONITOR.................................................12
WAKE ON LAN TECHNOLOGY ...................................13
CHAPTER 2 HARDWARE INSTALLTION........................................14
2-1
2-2
2-3
PREPARATIONS..............................................................14
UNPACKING THE MOTHERBOARD ...........................15
INSTALLATION GUIDE .................................................16
CPU Installation .....................................................17
DDR SDRAM Memory Module Installation............20
Motherboard Connector..........................................22
Jumper Setting.........................................................36
The synchronous/asynchronous clock mode between
2-3.1
2-3.2
2-3.3
2-3.4
2-3.5
CPU and memory interface setting ...................................................38
2-3.6
2-3.7
2-3.8
2-3.9
2-3.10
2-3.11
CPU Vcore adjustment (VJ1) ..................................38
CMOS Clearing (JP5).............................................39
Power On ................................................................40
Quick BIOS Setup....................................................41
Troubleshooting at First Start...............................42
Power Off..............................................................45
CHAPTER 3 BIOS SETUP UTILITY ..................................................46
3-1
SOYO COMBO SETUP ...................................................49
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SY-K7ADA V1.0
3-2
ADVANCED BIOS FEATURES ......................................54
ADVANCED CHIPSET FEATURES ...............................59
INTEGRATED PERIPHERALS.......................................62
POWER MANAGEMENT SETUP..................................66
PNP/PCI CONFIGURATION SETUP..............................70
PC HEALTH STATUS......................................................74
LOAD FAIL-SAFE DEFAULTS ......................................76
LOAD OPTIMIZED DEFAULTS.....................................77
SUPERVISOR PASSWORD ............................................78
USER PASSWORD ..........................................................79
IDE HDD AUTO DETECTION .......................................80
BOOT MENU ...................................................................81
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
CHAPTER 4 DRIVER INSTALLATION.............................................82
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
Chapter 1
MOTHERBOARD DESCRIPTION
1-1 INTRODUCTION
The SY-K7ADA V1.0 AGP/PCI Motherboard is a high-performance
Socket 462 ATX form-factor system board. Using ALI Chipset technology.
This Motherboard is fully compatible with industry standards and adds
many technical enhancements.
1-2 KEY FEATURES
ꢀ CPU SUPPORT
The SY-K7ADA V1.0 supports THE FOLLOWING AMD® CPUs:
ꢁ
Supports 200MHz Front Side Bus DDR(Double Data Rate) transfer
on Athlon(750MHz~1.2GHz)/ Duron(600MHz~850MHz)
ꢁ
Supports 266MHz Front Side Bus DDR (Double Data Rate) transfer
on Athlon(1GHz~1.2GHz)
ꢁ
Supports 266MHz Front Side Bus DDR (Double Date Rate) transfer
on Athlon Palomino(1500+~1800+)
New released AMD Socket 462 CPUs will very likely be supported by the
SY-K7ADA V1.0 as well.
ꢀ CPU SETTINGS
The SY-K7ADA V1.0 provides the user with a very complete and
convenient CPU setting environment. The CPU settings are all adjusted
through the DIP switch.
ꢁ
CPU Frequency
The SY-K7ADA V1.0 supports an incredible wide range of CPU
frequency settings:
600,650,700,750,800,850,900,950,1000+MHz.
This gives the SY-K7ADA V1.0 an overwhelming overclocking potential.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
CPU Multiplier
SY-K7ADA V1.0
ꢁ
ꢀ EXPANDABILITY
The SY-K7ADA V1.0 provides all the standard expansion slots, and many
more additional expansion features:
ꢂ Expansion slots
ꢁ
ꢁ
1 x 32-bit bus master AGP slot
5 x 32-bit bus master PCI slots
ꢂ Enhanced IO
ꢁ
ꢁ
Floppy disk controller
2x EIDE controllers with support for up to 4 Ultra DMA
33/66/100 devices
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Standard/EPP/ECP parallel port
2x 16550 compatible serial ports
IrDA compatible infrared port
6x USB (Universal Serial Bus) connectors
PS/2 mouse connector
PS/2 keyboard connector
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
ꢀ ADVANCED FUNCTIONS
The SY-K7ADA V1.0 supports advanced functions such as:
Wake-On-LAN
ꢁ
Supports Wake-On-LAN (Some advanced network cards can
wake the system up over the network, the WOL connector is
provided by the SY-K7ADA V1.0 to support this function).
ꢁ
Multiple boot
The SY-K7ADA V1.0 supports booting from devices such as
CD-ROM, FLOPPY DRIVE & HDD, LS120, SCSI, ZIP.
ꢁ
Power on by modem or alarm
If the SY-K7ADA V1.0 system is in suspend mode, it can be switched
back on through the modem or RTC alarm function. This opens a lot
of possibilities, such as remote access that switches the system on
only after the modem receives a call.
ꢀ FAIL SAFE
The SY-K7ADA V1.0 comes with added functionality to make managing
the system easy and safe
ꢂ Hardware Monitor
The integrated Hardware Monitor IC and Hardware doctor software
enables the user to monitor system voltages, temperatures and FAN speeds.
This makes sure that the user is in full control of the system
ꢀ SOYO Bonus Pack CD-ROM
ꢀ COMPLIANCE
The SY-K7ADA V1.0 complies with all important industry standards. The
following underlines the reliability of the SY-K7ADA V1.0, a
motherboard to trust.
ꢁ
PC99, ACPI compliant
ꢀ USER FRIENDLY
ꢁ
ꢁ
ꢁ
SOYO Combo Setup
Jumperless design
You can set up the following options through the BIOS setup
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
CPU FSB frequency
SY-K7ADA V1.0
PCI clock
AGP Clock
SDRAM Clock
ꢀ
HANDLING THE MOTHERBOARD
To avoid damage to your Motherboard, follow these simple rules while
unpacking:
ꢀ Before handling the Motherboard, ground yourself by grasping an
unpainted portion of the system's metal chassis.
ꢀ Remove the Motherboard from its anti-static packaging. Hold the
Motherboard by the edges and avoid touching its components.
ꢀ Check the Motherboard for damage. If any chip appears loose, press
carefully to seat it firmly in its socket.
Warning: Do not apply power if the Motherboard appears
damaged. If there is damage to the board, contact your dealer
immediately.
1-3 ELECTROSTATIC DISCHARGE PRECAUTIONS
Make sure to ground yourself before handling the Motherboard or other
system components. Electrostatic discharge can easily damage the
components. Note that you must take special precautions when handling
the Motherboard in dry or air-conditioned environment.
To protect your equipment from electrostatic discharge, take the following
precautions:
ꢀ Do not remove the anti-static packaging until you are ready to install.
ꢀ Ground yourself before removing any system component from its
protective anti-static packaging. (To ground yourself, grasp the expansion
slot covers or other unpainted portions of the computer chassis.)
ꢀ Frequently ground yourself while working or use a grounding strap.
ꢀ Handle the Motherboard by its edges and avoid touching its
components.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
1-4 SY-K7ADA V1.0 MOTHERBOARD LAYOUT
PS/2 KB
Connector
PS/2 Mouse
Connector
JP1
1
3
USB 1_2
COMA
FJ1
PRT
COMB
AGAME
ATX Power
ALi
AOUT
AIN
M1647
VJ1
AMIC
IDE 2 IDE 1
3
1
ALi
M5879
VJ2
AGP Slot
4
1
Sigmatel
STAC9700
CDIN1
PCI Slot #1
PCI Slot #2
PCI Slot #3
PCI Slot #4
ALi
M5819
ALi
FLP
M1535D+
RJ2
3
RJ1
1
3V
Lithium
Battery
PCI Slot #5
RJ3
3
1
1112 13 14 15 16 17 18 19 20
JP5
JP10
WOL
Header
1
2
3
4
5
9
10
3
1
Back Panel
SY-K7ADA Platform
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
1-5 SY-K7ADA V1.0 MOTHERBOARD COMPONENTS
A
B
C
D
E
F
AE
G
H
I
J
K
AD
AC
AB
AA
L
Z
M
Y
X
N
O
W
V
P
U
T
S
R
Q
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
A
B
C
D
E
F
G
H
I
K/B Power-On setting Jumper
CPU Vcore adjustment setting switch
Socket 462 Connector
DIMM Banks
CPU Cooling Fan Connector
CPU FSB adjustment setting switch
Bus Mastering E-IDE/ATAPI Ports
ALi M1647 North Bridge chip
SYS Cooling Fan
J
CPU Vcore setting Jumper
32-bit AGP 1X/2X/4X Slot
Floppy Disk Drive (FDD) Port
K
L
M ALi M1535D+ South Bridge chip
N
O
P
32-bit PCI Mastering Slots
Serial Infrared (IrDA) Device Header
Chassis Cooling Fan
Q
R
S
Front panel Connectors
CPU Multiplier setting Jumper
USB3_4 and USB 5_6 Connectors
Wake-On-LAN (WOL) Header
CMOS Clear Jumper
T
U
V
3V Lithium Battery
W CPU Multiplier adjustment setting switch
X
Y
Z
CPU Multiplier setting Jumper
Flash BIOS
R.T.C. and CMOS RAM
AA Hardware Monitor
AB Sigmatel STAC9700 Chip
AC CD In Connector
AD ATX Power Supply Connector
AE Back panel Connectors
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
1-6 MICROPROCESSOR
The motherboard supports a single Socket 462 processor. The processor’s
VID pins automatically program the voltage regulator on the motherboard
to the required processor voltage. In addition, the front side bus speed
(200/266 MHz ) is automatically selected. The motherboard supports all
current Socket 462 processor speeds, voltages, and bus frequencies.
1-6.1 Microprocessor Packaging
The CPU is packaged in a 462 pin PGA package. A fan must be used to
ensure adequate cooling.
1-6.2 Second Level Cache
The second-level cache is located on the substrate of the CPU package.
The cache includes Athlon-256KB / Duron-64KB of synchronous
pipelined burst static RAM. All supported onboard memory can be cached.
1-6.3 Microprocessor Upgrades
The motherboard can be upgraded with Socket 462 processors that run at
higher speeds. When upgrading the processor, use the BIOS configuration
mode or DIP switch to change the processor speed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
1-7 CHIPSET
ꢀ
ALi M1647 Overview
The M1647 is a high performance, high value North Bridge that supports
all Athlon family processors. Internally all 128-bit architecture with
optimization for S2K bus, DDR and AGP4X interface, the M1647 has
outstanding high system performance under all types of system operations.
The M1647 North Bridge, coupled with one of ALi’s widely adopted PCI
South Bridge devices (M1535D+) provides a flexible and scalable
motherboard core logic solution to fill all applications.
The M1647 supports all Athlon family microprocessors. Processor bus
speeds of 66MHz to 133MHz are supported. This interface has 16 entries
for outstanding processor commands and system probe commands. This
interface supports FID change protocol for mobile purposes.
The M1647 can support up to 3.0 GB of SDRAM or DDR-SDRAM main
memory. Supports any combination of 66/100/133MHz memory bus
frequency and CPU bus frequency with minimized internal protocol
handshaking overhead, the M1647 provides a flexible system application.
In addition to dynamic memory power down, the M1647 also supports a
dynamic gated clock for the internal chipset logic circuitry, which will
reduce the system power consumption for mobile applications. The m1647
support the CAS-before-RAS refresh scheme and Self-refresh scheme
during normal mod and suspend mode, respectively.
The memory access controller plays a key role of dispatching the job to
the memory interface. By using a two-level dynamic arbitration scheme,
the M1647 fulfills multiple demanding sources that need access to the
main memory with balanced latency and maximum throughput. Another
important role of the memory access controller is the integration logic
between the AGP interface and main memory to support the AGP memory
address to physical memory address translate. To fulfill this function, the
M1647 uses 128 entries and 16 tags to implement a one level GART
(Graphic Address Re-mapping Table) scheme.
The M1647 supports all features of the AGP version 2.0 specification. This
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
boosts the graphic benchmarks into another era for professional graphics
usage. The M1647 design is capable of supporting 28 outstanding AGP
commands (depth of command queue=28) and buffering 64QW for AGP
master read operations.
The M1647 is fully compliant with the PCI 2.2 specification. Flexible PCI
latency control allows the M1647 to achieve improved system
performance.
The M1647 PCI host interface features a flexible PCI latency controller
that allows a system to be tuned for the best system performance possible.
The m1647 also features an enhanced PCI arbiter that implements a fair
arbitration scheme based on a PCI and time slice mechanism. In addition
to itself and the South Bridge, the M1647 can support up to six addition
PCI masters. This gives designers the ultimate in flexibility when deciding
what combination of PCI slots and on board PCI peripheral devices to use.
One of these six PCI master channel can be assigned to a higher priority
than other five PCI masters in order to fulfill the demands of some special
real time devices, e.g. 1394 isochronous transmissions, when accessing
main memory.
Dark Green Power Management functions such as Power on Suspend,
Suspend to RAM, Suspend to Disk, PCI bus CLKRUN and Dynamic
Clock Stop are all supported. The M1647 provides the most flexible power
management capability available in any chipset.
ꢀ
ALi M1535D+ Overview
The M1535D+ provides the best desktop system solution. The M1535D+
integrates AC-Link Host Controller, Hardware SoundBlaster Pro/16
compatibility, Host Signal Processing (HSP) software modem solution,
ACPI support, green function, 2-channel dedicated ATA-100 IDE Master
controller, 2 USB controllers, SMBus controller, PS/2 Keyboard/Mouse
controller, the Super I/O (Floppy Disk Controller, 2 serial port/1 parallel
port) support and Fast IR into one chip.
The built-in I/O in M1535D+ is an advenced Super I/O controller
containing all of the basic IBM PC, XT, AT peripherals. It incorporates
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
three full function universal asynchronous receiver/transmitters (UARTs),
a flexible high performance internal data separator with send/receive 16
byte FIFOs. It is also suitable for notebook computers since it has Fast
Infra Red for wireless communications with other devices. It can swap the
floppy drives A & B. It supports SPP, PS/2, EPP and ECP parallel port. It
also has a programmable baud rate generator. It has high performance
power management for the FDC, UART and parallel port.
The built-in audio in M1535D+ is an advanced PCI audio accelerator
providing wave table synthesis, DirectMusic, DirectSound3D for the high
performance, cost-sensitive consumer market. It also supports full Sound
Blaster compatibility and is fully PC’98/PC’99 compliant. The M1535D+
Audio, combined with a standard AC’97/AC’98 Codec, provides better
than CD quality audio with sound-to-noise ratio of > 90 db, up to 48 KHz
sample rate, full duplex audio with independent playback and recording
sample rate, 6-channel mixer and optional 3D surround sound enhanced
output. In the legacy DOS game environment, the M1535D+ audio
accelerator provides SoundBlaster Pro/16 compatibility, OPL2 and OPL3
emulation, and 1 to 8 MB of general MIDI music through the MPU 401
compatible interface. With built-in support of the legacy mode analog
game port, the M1535D+ audio can replace all the functions of wave table
based legacy audio ISA card. In addition, the M1535D+ supports
consumer audio digital interface (SPDIF) to connect external digital audio
equipment.
The M1535D+ will provide the AC’97 2.1 compliant digital controller
interface for third parties (such as the AMC Codec’s vendor) to enable the
software modem solution. The M1535D+ provides 4 separate telephony
bus master channel. One for modem output, one for modem input, one for
handset input, and one for handset output. The M1535D+ supports the
Modem on-demand variable sample rate transfer, power management ,
wake-up, and caller ID string transmission.
The M1535D+ will support the security feature such as the platform
firmware protection. The M1535D+ also provides the ability to meet the
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
Legacy-Free and Legacy Reduction specification of PC2001.
1-7.1 PS/2 Keyboard and Mouse Interface
PS/2 keyboard and mouse connectors are located on the back panel of the
motherboard. The +5 V lines to keyboard and mouse connectors are
protected with a fuse that prevents motherboard components from being
damaged when an over-current condition occurs.
Note
The mouse and keyboard can be plugged into either PS/2 connector.
Power to the computer should be turned off before a keyboard or mouse is
connected or disconnected.
The keyboard controller contains code, which provides the traditional
keyboard and mouse control functions, and also supports Power On/Reset
password protection. Power On/Reset password can be specified in the
BIOS Setup program.
The keyboard controller also supports the hot-key sequence
<Ctrl><Alt><Del>, software reset. This key sequence resets the
computer’s software by jumping to the beginning of the BIOS code and
running the Power On Self Test (POST).
1-8 HARDWARE MONITOR
The hardware monitor subsystem provides instrumentation capabilities.
The features of the hardware monitor subsystem include:
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
2 thermistor input for remote temperature sensing (CPU/System)
Monitor 4 positive voltages (Vcore/+3.3V/+5V/+12V)
Monitor 2 fan speeds
2 PWM outputs for fan speed control
Power-on beep warning when CPU core voltage is out of range
VID4-VID0 monitoring inputs
Windows 95/98 utility included
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7ADA V1.0
1-9 WAKE ON LAN TECHNOLOGY
Wake on LAN technology enables remote wakeup of the computer
through a network. Wake on LAN technology requires a PCI add-in
network interface card (NIC) with remote wakeup capabilities. The remote
wakeup connector on the NIC must be connected to the onboard Wake on
LAN connector. The NIC monitors network traffic at the Ethernet interface;
upon detecting a Magic Packet, the NIC asserts a wakeup signal that
powers up the computer. This feature uses the Wake on LAN connector.
ꢀCAUTION
For Wake on LAN, the 5-V standby line for the power supply must be
capable of delivering +5V ±5 % at 720 mA. Failure to provide adequate
standby current when implementing Wake on LAN can damage the power
supply.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
Chapter 2
HARDWARE INSTALLATION
Congratulations on your purchase of SY-K7ADA V1.0 Motherboard. You
are about to install and connect your new Motherboard.
Note: Do not unpack the Motherboard from its protective
anti-static packaging until you have made the following
preparations.
2-1 PREPARATIONS
Gather and prepare all the following hardware equipment to complete the
installation successfully:
1.
Socket 462 processor with built-in CPU cooling fan (boxed type).
Note: This Motherboard supports non-boxed type CPUs. The heavier
CPU cooling fan requires the installation of a CPU support stand.
2.
3.
4.
5.
6.
7.
8.
9.
10.
DDR RAM memory module (s)
Computer case and chassis with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device (PS/2 mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive…
External Peripherals: Printer, Plotter, and Modem (optional)
Internal Peripherals: Modem and LAN cards (optional)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-2 UNPACKING THE MOTHERBOARD
When unpacking the Motherboard, check for the following items:
ꢂ
The SY-K7ADA V1.0 ALi MAGIK1 AGP/PCI
Motherboard
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
The Quick Start Guide
The Installation CD-ROM
SOYO Bonus Pack CD-ROM
One IDE Device ATA33/66/100 Flat Cable
One Floppy Disk Drive Flat Cable
One Heat Sink Compound
Warning: Do not unpack the Motherboard from its anti-static
packaging until you are ready to install it.
Like most electronic equipment, your Motherboard may be damaged by
electrostatic discharge. To avoid permanent damage to components ground
yourself while working by using a grounding strap. Otherwise, ground
yourself frequently by touching the unpainted portion of the computer
chassis to drain the static charges.
Handle the Motherboard carefully, hold it by the edges.
You are now ready to start the installation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3 INSTALLATION GUIDE
We will now begin the installation of the Motherboard. Please follow the
step-by-step procedure designed to lead you to a complete and correct
installation.
Warning: Turn off the power to the Motherboard, system
chassis, and peripheral devices before performing any work on
the Motherboard or system.
BEGIN THE INSTALLATION
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.1 CPU Installation
Your SY-K7ADA V1.0 motherboard comes with a CPU retention set kit.
The retention set is used to hold the processor attached to the Socket 462
CPU connector on the motherboard.
Mark your CPU Frequency: Record the working frequency of
your CPU that should be clearly marked on the CPU cover.
200MHz FSB Athlon CPU
750 MHz (100 x 7.5)
800 MHz (100 x 8.0)
850 MHz (100 x 8.5)
1.2GHz(100 x 12.0)
900 MHz (100 x 9.0)
1.3GHz (100 x 13.0)
950 MHz (100 x 9.5)
800 MHz (100 x 8.0)
1000 MHz (100 x 10.0)
1.1GHz (100 x 11.0)
200MHz FSB Duron CPU
600 MHz (100 x 6.0)
650 MHz (100 x 6.5)
700 MHz (100 x 7.0)
750 MHz (100 x 7.5)
850 MHz (100 x 8.5)
900 MHz (100 x 9.0)
266MHz FSB Athlon CPU
1 GHz (133 x 7.5)
1.13 GHz (133 x 8.5)
1.2 GHz (133 x 9.0)
1.33 GHz (133 x 10.0)
1800+
266MHz FSB Athlon Palomino CPU
1500+
1600+
1700+
Follow these instructions to install your Socket 462 processor correctly.
1. Lift the socket handle up to a vertical position.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2. Align the blunt edge of the CPU with the matching pinhole
distinctive edge on the socket.
3. Seat the processor in the socket completely and without forcing.
4. Then close the socket handle to secure the CPU in place.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
Remember to connect the CPU Cooling Fan to the
appropriate power connector on the Motherboard. The fan is
a key component that will ensure system stability. The fan
prevents overheating, therefore prolonging the life of your
CPU.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2 DDR SDRAM Memory Module Installation
Your board comes with three DIMM sockets, providing support for up to
3GB of main memory using DDR RAM modules from 4Mb to 512Mb. On
this motherboard, DRAM speed can be set independent from the CPU
front side bus speed. Appropriate memory modules must be used. Supports
DDR frequency 100/133 MHz.
92
1
1
92
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
Memory Configuration Table
Number of Memory
DIMM 1
DIMM 2
DIMM 3
Modules
RAM Type
DDR SDRAM
4/16/32/64/128/256/512 Mbit
Memory Module Size
Note: This Motherboard can only support 2 pcs of PC2100 DDR
module, we suggest using DIMM1 and DIMM2 for PC2100 DDR
module.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
Motherboard Connector
Pin-1
IDE 2
Secondary Primary
IDE IDE
IDE 1
2-3.2.1 IDE Device Installation (HDD, CD-ROM)
This Motherboard offers two primary and secondary IDE device
connectors (IDE1, IDE2). It can support up to four high-speed Ultra DMA
33/66/100HDD or CD-ROM.
Connect one side of the ATA33/66/100 flat cable to the IDE device (HDD
or CD-ROM) and plug the other end to the primary (IDE1) or secondary
(IDE2) directionally keyed IDE connector on the Motherboard. The
ATA33/66/100 cable is backward compatible with ATA33 HDDs.
This Motherboard can support up to four HDDs.
80-Conductor
ATA 66/100
Flat Cable
40-pin
1
1
39
39
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2.2Floppy Drive Installation
Pin -1
FDC
Floppy Drive
Connector
The system supports 5 possible floppy drive types: 720 KB, 1.2 MB,
1.44 MB, 2.88 MB, and LS-120.
Connect one side of the 34-pin flat cable to the floppy drive and plug the
other end to the floppy drive connector on the Motherboard.
This Motherboard can support up to 2 floppy drives.
1
1
33
33
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2.3 Front Panel Connections
1112 13 14 15 16 17 18 19 20
1 2 3 4 5
9 10
Plug the computer case's front panel devices to the corresponding headers
on the Motherboard.
1. Power LED
Please install according to the following pin assignment: pin 1,3 are for
Power LED.
Power LED
Pin Assignment
Pin11 Pin12 Pin13
_
+
LED
NC
GND
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2. Reset
Plug the Reset push-button cable into the 2-pin Reset header on the
Motherboard. Pushing the Reset button on the front panel will cause the
system to restart the boot-up sequence.
Reset Pin Assignment
Pin1
Pin2
Power RST
GND
3. Speaker
Attach the 4-pin PC speaker cable from the case to the Speaker header on
the Motherboard.
Speaker Pin Assignment
Pin17 Pin18 Pin19 Pin20
_
+
Speaker out
Power
NC NC
4. IDE LED
Attach the 2-pin IDE device LED cable to the corresponding IDE LED
header on the Motherboard. This will cause the LED to light up when an
IDE (HDD, CD-ROM) device is active.
HDD LED Pin Assignment
Pin9
Pin10
_
+
Power
HDD LED
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
5. ATX Power On/Off Switch
Attach the 2-pin momentary type switch to the PWRBT header for turning
On or Off your ATX power supply.
PWRBT Pin Assignment
Pin4 Pin5
PWRBTN
GND
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2.4 Back Panel Connections
All external devices such as the PS/2 keyboard, PS/2 mouse, printer,
modem, USB1, USB2 can be plugged directly onto the Motherboard back
panel.
Only after you have fixed and locked the Motherboard to the computer
case can you start connecting the external peripheral devices.
When connecting an external device, use the following figure to locate and
identify which back panel connector to plug the device to.
PS/2 KB PS/2 Mouse
Connector
Connector
USB 1_2
COMA
PRT
COMB
AOUT
AGAME
AIN
AMIC
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
1. Onboard Serial Ports COM1/COM2
External peripherals that use serial transmission scheme include:
-
-
serial mouse,
and modem.
Plug the serial device cables directly into the COM1/COM2 9-pin male
connectors located at the rear panel of the Motherboard.
2. Parallel Port PRT
This parallel port is used to connect the printer or other parallel devices.
Plug the parallel device cable into the 25-pin female connector located at
the rear panel of the Motherboard.
3. PS/2 Keyboard
Plug the keyboard jack directly into the 6-pin female PS/2 keyboard
connector located at the rear panel of the Motherboard.
Pin5
KBD Clock
Pin6
NC
Pin4
VCC
Pin3
GND
Pin1
KBD DATA
Pin2
NC
4. PS/2 Mouse
Similarly, plug the mouse jack directly into the 6-pin female PS/2 mouse
connector.
Pin5
Mouse Clock
Pin6
NC
Pin4
VCC
Pin3
GND
Pin1
Mouse DATA
Pin2
NC
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
5. Universal Serial Bus (USB3, USB4/USB5, USB6)
This Motherboard provides four USB ports for your additional devices.
Plug the USB device jack into the available USB connector USB3, USB4,
USB5 and USB6 via USB cable.
-
Standard device drivers come with the Win98 for commonly used
USB devices.
-
With Win95, use the flow OpenHCI 1.0a specifications. To use USB
devices under Win95, usually you have to install the device that
driver comes with the USB device you have purchased.
USB3
USB4
6
1
2
+5V
+5V
7
(-)Data
(-)Data
(+)Data
(+)Data
8
9
3
4
GND
NC
GND
GND
5
10
USB5
USB6
6
1
2
+5V
+5V
7
(-)Data
(-)Data
(+)Data
(+)Data
8
9
3
4
GND
NC
GND
GND
5
10
6. Onboard Joystick port/audio
This Motherboard provides Joystick port and audio.
-
Attach the joystick cable to the 15-pin JOYSTICK port at the rear
panel of you motherboard.
-
This Motherboard features three built-in audio-stereo ports (labeled
line-in, line-out, and mic jack) convenient to directly plug-in all your
external audio devices.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2.5 Other Connections
1. Wake-On-LAN (WOL)
Attach the 3-pin connector from the LAN card which supports the
Wake-On-LAN (WOL) function to the JP10 header on the Motherboard.
This WOL function lets users wake up the connected computer through the
LAN card.
Please install according to the following pin assignment:
Wake-On-LAN
JP10 Pin Assignment
3
2 1
PME#
GND
5VSB
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2. Infrared
Plug infrared device cable to the SIRCON header. This will enable the
infrared transfer function. This Motherboard meets both the IrDA 1.0 (SIR)
and IrDA 1.1 (FIR and MIR) specifications. Supports sharp-IR.
Please install according to the following pin assignment:
Standard Infrared
(SIRCON) Connector
SIRCON Pin Assignment
3
5 6
1 2
4
OVCROFF
IRTX
IRRX
+5V
GND
3. Other Display Cards
Insert other types of VGA cards into the PCI or ISA expansion slots
according to card specifications.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
4. Cooling Fan Installation
(1) CPU Cooling Fan
After you have seated the CPU properly on the processor, attach the 3-pin
fan cable to the CPUFAN connector on the Motherboard. The fan will stop
when the system enters into Suspend Mode. (Suspend mode can be
enabled from the BIOS Setup Utility, [POWER MANAGEMENT] menu.)
To avoid damage to the system, install according to the following pin
assignment:
CPU Cooling Fan
CPUFAN Pin Assignment
3
1 2
12V
GND
SENSOR
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
(2) Chassis Cooling Fan
Some chassis also feature a cooling fan. This Motherboard features a
CHAFAN connector to provide 12V power to the chassis fan. Connect the
cable from the chassis fan to the CHAFAN 3-pin connector. Install
according to the following pin assignment:
Chassis Cooling Fan
CHAFAN1 Pin Assignment
1
2
3
PWM2
+12V
SENSOR
(3) Chipset Cooling Fan
Some chipset also feature a cooling fan. This Motherboard features a
ChipFAN connector to provide 12V power to the chassis fan. Connect the
cable from the chassis fan to the ChipFAN 3-pin connector. Install
according to the following pin assignment:
Chipset Cooling Fan
ChipFAN Pin Assignment
3
1 2
12V
GND
NC
Note: CPUFAN/ChipFAN must be installed for this Motherboard,
CHAFAN is optional.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
5. CD Line-in (CDIN1)
This Motherboard provides two CD-Line in connectors. Please connect the
4-pin audio cable from your CD-ROM drive to either CDIN1. (It fits in
only one, depending on the cable that came with your CD-ROM drive)
Please install according to the following pin assignment:
CD-IN: CDIN1
Right
4
GND
GND
Left
3
2
1
2-3.2.6 AGP VGA Card
Insert the AGP VGA card into the AGP slot. Then connect the monitor
information cable to the AGP card back plane external connector.
Follow the manufacturer's instructions to perform the AGP VGA drivers
installation.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.2.7 ATX Power Supply
ATX Power
Plug the connector from the power directly into the 20-pin male ATX PW
connector on the Motherboard, as shown in the following figure.
Warning: Follow these precautions to preserve your
Motherboard from any remnant currents when connecting to
ATX power supply:
Turn off the power supply and unplug the power cord of the
ATX power supply before connecting to ATX PW connector.
The Motherboard requires a power supply with at least 200 Watts and a
"power good" signal. Make sure the ATX power supply can take at least
720 mA * load on the 5V Standby lead (5VSB) to meet the standard ATX
specification.
* Note: If you use the Wake-On-LAN (WOL) function, make sure the
ATX power supply can support at least 720 mA on the 5V Standby lead
(5VSB).
Please install the ATX power according to the following pin assignment:
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
ATX Power
12V
5VSB
PW-OK
GND
5V
5V
5V
-5V
GND
GND
GND
PS-ON
GND
-12V
3.3V
ꢀ Pay special care to the directionality.
GND
5V
GND
3.3V
3.3V
2-3.3 Jumper Setting
2-3.3.1Multiplier Adjustment Setting (RJ1)
For certain AMD CPUs, the multiplier is not locked such that
setting a multiplier higher than specified on the CPU is possible.
For technical details read the following:
Refer to the following table to set the Frequency Multiplier of your CPU.
Frequency
Multiplier Setting
RJ2
RJ3
Auto
Short Pin1-2
Short Pin1-2
1 2
3
1 2
3
Short Pin2-3
Short Pin2-3
Manual
1 2
3
1 2
3
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
If you set ratio to manual and configure the RJ1 DIP Switch to the settings
that match your CPU speed, as follow table:
RJ1
5
5.5
6
1
2
3
Off
Off
4
RJ1
9
9.5
10
1
2
3
4
Off Off
Off Off
On On
Off
On
On
On
On
On On
Off
On
On
Off Off
On
Off Off Off
Off Off Off
On On On
Off Off Off Off
On On On On
6.5
7
On 10.5
Off
11
7.5
8
8.5
Off On On Off 11.5 Off On On On
On Off On Off
Off Off Off
12
12.5
On Off On On
Off Off
On
On On
Note: SOYO does not guarantee system stability if the user over
clocks the system. Any malfunctions due to over-clocking are not
covered by the warranty.
2-3.3.2Enable/Disable Power-On by Keyboard (JP1)
You may choose to enable the Power-On through Keyboard function by
shorting pin 2-3 on jumper JP1; or short pin 1-2 to disable this function.
Power-On by
Enable
Disable
Short pin 1-2
and the
Power-On by
Keyboard
function is
disabled.
Keyboard
Short pin 2-3 to
enable the
Power-On by
Keyboard
JP1 Setting
1 2 3
1 2 3
function.
Important: When using the Power-On by Keyboard function, please
make sure the ATX power supply is able to provide at least 720mA on
the 5V Standby lead (5VSB) in order to meet the standard ATX
specification.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
2-3.4 The synchronous/asynchronous clock mode
between CPU and memory interface setting
The FSB Frequency can be set through DIP switch FJ1 or BIOS and it
may therefore differ from the Frequency the CPU specifies. Doing so
may however force your CPU to operate out of its specifications and
therefore SOYO can not guarantee the proper functioning of your
system.
Refer to the following table:
CPU Freq(MHz) SDRAM(MHz
1
2
3
4
133
133
On
Off
Off
Off
2-3.5 CPU Vcore adjustment (VJ1)
Refer to following table to set the voltage of your CPU. If you set VJ2
status to AUTO, please set VJ1 switch status to Off (all).
Status Setting
Manual
VJ2
Short Pin2-3
1 2
3
Auto
Short Pin1-2
1 2
3
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7ADA V1.0
If you set status to manual and configure VJ1 switch to the settings that
match your CPU voltage as follow table:
1
2
3
4
5
1
2
3
4
5
VJ1
VJ1
OFF OFF OFF OFF ON
Auto OFF OFF OFF OFF OFF 1.475
1.100 ON OFF OFF OFF OFF 1.500 ON OFF OFF OFF ON
1.125 OFF ON OFF OFF OFF 1.525 OFF ON OFF OFF ON
1.150 ON ON OFF OFF OFF 1.550 ON ON OFF OFF ON
OFF OFF ON OFF OFF
OFF OFF ON OFF ON
1.575
1.175
1.200 ON OFF ON OFF OFF 1.600 ON OFF ON OFF ON
1.225 OFF ON ON OFF OFF 1.625 OFF ON ON OFF ON
ON ON ON OFF OFF
OFF OFF OFF ON OFF
ON OFF OFF ON OFF
OFF ON OFF ON OFF
ON ON OFF ON OFF
OFF OFF ON ON OFF
ON OFF ON ON OFF
ON ON ON OFF ON
OFF OFF OFF ON ON
ON OFF OFF ON ON
OFF ON OFF ON ON
ON ON OFF ON ON
OFF OFF ON ON ON
ON OFF ON ON ON
1.250
1.275
1.300
1.325
1.350
1.375
1.400
1.650
1.675
1.700
1.725
1.750
1.775
1.800
1.425 OFF ON ON ON OFF 1.825 OFF ON ON ON ON
1.450 ON ON ON ON OFF 1.850 ON ON ON ON ON
2-3.6 CMOS Clearing (JP5)
After you have turned off your computer, clear the CMOS memory by
momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then
restore JP5 to the initial 1-2 jumper setting in order to recover and retain
the default settings.
Jumper JP5 can be easily identified by its white colored cap.
CMOS
Clearing
Clear CMOS Data
Retain CMOS Data
Short pin 2-3 for
at least 5 seconds to
clear the CMOS
Short pin 1-2
to retain new
settings
JP5 Setting
1 2 3
1 2 3
Note: You must unplug the ATX power cable from the ATX power
connector when performing the CMOS Clear operation.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
2-3.7 Power On
You have now completed the hardware installation of your Motherboard
successfully.
1. Turn the power on
2. To enter the BIOS Setup Utility, press the <DEL> key while the system
is performing the diagnostic checks,
Note: If you have failed to enter the BIOS, wait until the boot up
sequence is completed. Then push the RESET button and press
<DEL> key again at the beginning of boot-up, during diagnostic
checks.
Repeat this operation until you get the following screen.
3. The BIOS Setup screen appears:
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀSoyo Combo Feature
ꢀPC Health Status
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Peripherals
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
ꢀPower Management Setup
ꢀPnP/PCI Configurations
Save & Exit Setup
Exit Without Saving
Esc : Quit
ꢃꢄꢅꢆ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
40
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
2-3.8 Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU
frequency. Instead, CPU settings are software configurable with the BIOS
[SOYO COMBO SETUP]. The [SOYO COMBO SETUP] menu
combines the main parameters that you need to configure, all in one menu,
for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then
press the <DEL> key during the system diagnostic checks to enter the
Award BIOS Setup program. The CMOS SETUP UTILITY will display
on screen. Follow these steps to configure the CPU settings.
Step 1. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to
“Auto”.
Step 2. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt
to load the BIOS optimal setup.
Step 3. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and
continue the boot sequence.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
2-3.9 Troubleshooting at First Start
Video (no display) related issues
I built a new computer system using a Soyo board and nothing
happens when turning it on, no video and no beeps from the PC
speaker. What is happening and how can it be fixed?
No screen and no beeps mean that your CPU and motherboard do not
work at all. It could be that the CPU is not seated correctly or that a
component on the M/B is grounded (shorted) with the case. Also make
sure to check the voltage setting switch (110V/220V) on the back of the
power supply. To isolate the problem do the following:
1. Press and hold down on the “Ins” (insert) key while turning on the
computer until you get video. If you do not get video then,
2. Double-check jumpers setting on you motherboard and remove all
add-on cards, unplug all hard-disk and floppy-disk drive cables and see if
you can hear some beeps. If you still do not get any beeps, then try putting
the motherboard on the table (to isolate it from the case) with the CPU and
speaker only, and give it one more try.
I hear a series of beeps and I do not get anything from my monitor.
What could be wrong?
The following lists some basic beep codes and their possible meanings:
•
One long beep and 3 very short beeps - The video card is not
detected by the motherboard. Please re-seat your video card. If
you are using an AGP card, please push your AGP card down
real hard. You may have to push VERY hard without the AGP
card mounting screw. Make sure not to insert the card the other
way around.
•
Continuous beeps – One or more of the memory modules is not
seated correctly in its socket.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
My PCI VGA card works fine with my system, but when I put in a
new AGP card, it does not give me any video. Is my AGP slot bad?
This is a common problem with AGP video cards. The reason is that your
AGP card did not get seated into the AGP slot fully and firmly. Please
push your AGP card down into the socket real hard, it should snap twice.
You may have to unscrew the AGP card to allow the card to go further
down. Do take care not to damage the card by using too much force.
I get distorted video my AGP card right after I save my bios. Why is
that?
The cause is likely that your AGP card is not running at the correct bus
speed. To fix this, please clear the CMOS ALi JP5 and if it still does not
work, please upgrade your motherboard bios to the latest version.
BIOS Issues
Where can I find the BIOS revision of my mainboard?
It will be displayed on the up-left corner on the screen during boot-up. It
will show as your board type followed by the revision number, such as
5EH_2CA1 (meaning revision 2CA1 for the SY-5EH board) or 6BA+
IV_2AA2 which means SY-6BA+ IV motherboard with 2AA2 bios.
Where can I find the latest BIOS of my motherboard?
Please go to the technical support page of one of the SOYO websites
the latest BIOS revision.
Hard disk, floppy drive, CD-ROM etc
When I boot up my new computer I got "floppy boot failure" and the
LED on the floppy stays on
Make sure the red wire of floppy ribbon cable goes to Pin1 on the floppy
drive side (don't trust the "key lock" or "notch") and use the end-connector
of the cable (don't use middle one).
Modem issues
I get an "I/O Conflict" message when I turn on my system and I can
not get my modem to work
43
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
What you need to do is to disable 'COM2' (or UART2 or serial port 2) in
the bios under integrated peripheral setup.
I have installed my modem drivers several times and I still cannot get
my modem to work. Why?
If you are sure that the modem driver has been installed correctly, then you
need to install the south bridge driver from the SOYO CD, this is because
Windows does not properly recognize relatively new chipsets.
Audio Issues
I do not get any sound from my sound card. What could be wrong?
Please make sure the speaker is connected to the speaker out port on your
sound card.
In Device Manager, I keep getting yellow exclamation signs on my
sound port even though I have installed my sound driver several times
and I could not get my sound card to work. What is wrong?
It is likely that you did not have the correct driver installed. If you are sure
that the correct sound driver has been installed, then please install the
'south bridge' driver for the motherboard.
The sound is working in my system, but when I play CD music from
the CD-ROM, I do not get any sound. What is wrong?
This is because the 3-wire audio cable from the CD-ROM to the sound
card is not connected or it is loose.
The sound from my sound card is distorted when Windows starts.
What is wrong?
First, if you are using an ISA sound card, please make sure the IRQ
needed for the sound card is set to 'Legacy ISA' in the bios. In other words,
if your ISA sound card takes IRQ5, then set IRQ5 to 'Legacy ISA'. Next,
install the 'south bridge' driver for the motherboard.
The sound and everything else works fine except that the recorder and
microphone do not work. What is wrong?
44
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
This is because the recorder and microphone in the Windows are not
enabled. Please go to sound properties and enable them.
Lock up (freeze)
When I boot up my system, everything works fine. It sees my CPU
and memory, detects my hard drive, floppy drive and CD-ROM but
locks up at "Verify DMI pool data... ", and it won’t go any further.
What should I do?
Please clear the CMOS ALi JP5 then choose 'load fail-safe default' in the
bios and save the bios and exit. Next, unplug all other add-on cards except
the video card and floppy drive controller, and see if it can boot from
floppy. Then put back the peripherals one by one to identify which one
causes the lockup.
I can not get my board to run properly.
Please make sure you have the latest bios and driver from the SOYO web
site at: http://www.soyo.com
2-3.10 Power Off
There are two possible ways to turn off the system:
1. Use the Shutdown command in the Start Menu of Windows 95/98
to turn off your computer.
2. Press the mechanical power-button and hold down for over 4
seconds, to shutdown the computer. If you press the power-button for
less than 4 seconds, then your system will enter into Suspend Mode.
You are now ready to configure your system with the BIOS setup program.
Go to Chapter 3: BIOS SETUP
45
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Chapter 3
BIOS SETUP UTILITY
This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS
program from Award Software Inc.
To enter the Award BIOS program's Main Menu:
1. Turn on or reboot the system.
2. After the diagnostic checks, press the [Del] key to enter the Award
BIOS Setup Utility.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀSOYO COMBO Feature
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Peripherals
ꢀPC Health Status
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
ꢀPower Management Setup
ꢀPnP/PCI Configurations
Save & Exit Setup
Exit Without Saving
Esc : Quit
ꢃꢄꢅꢆ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Selecting items
ꢇ
ꢇ
Use the arrow keys to move between items and select fields.
From the Main Menu press arrow keys to enter the selected submenu.
Modifying selected items
ꢇ
Use the [Up]/[Down] keys to modify values within the selected fields.
Some fields let you enter values directly.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Hot Keys: Function keys give you access to a group of commands
throughout the BIOS utility.
Function Command
Description
Gives the list of options available for each
item.
F1
General Help
Previous
Values
Restore the old values. These are the values
that the user started the current session with.
F5
Load
Loads all items with the most conservative
values.
F6
F7
Fail-Safe
Defaults
Load
Optimized
Defaults
Save
Loads all options with the optimize values.
F10
Saves your changes and reboots the system.
Returns at anytime and from any location to
the Main Menu.
[Esc]
Exit
Will display a overlapping window with all
options for the current item.
[Enter]
Select
Using the +, –, Page Up and Page Down
keys the user can toggle the value of the
current item.
[+/–/PU/PD] Value
47
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
SAVE AND EXIT SETUP
Select the [SAVE & EXIT SETUP] option from the Main Menu to save
data to CMOS and exit the setup utility. This option saves all your changes
and causes the system to reboot.
R
O
O
M
S
P
C
I / I S
A
B
I O
I L I T
I N
S
C
M
S
E
T
U
T
P
U
T
Y
Type [Y] to save the
changes and exit or [N]
to return to the Main
Menu and keep current
values.
A
W
A
R
D
S
O
F
W
A
R
E
,
C
.
T
S
B
C
P
P
L
T
A
N
D
F
A
E
R
D
C
M
O
S
S
E
T
U
P
I N
T
E
G
R
A
E
D
P
E
R
I P
H
E
R
A
L
S
I O
H
S
I P
W
P
S
E
O
E
/ P
D
R
C
S
B
SAVE to CMOS and EXIT
N
O
A
L
O
A
D
I O
S
D
E
F
A
U
L
T
S
E
F
s
c
:
:
Q
S
u
i t
↑
↓
h
→
←
:
:
S
C
e
h
l e
a
c
t
I t e
m
o
1
0
a
v
e
&
E
x
i t
S
e
t
u
p
( S
D
i f t )
F
2
n
g
e
C
l o
r
T
i m
e
,
D
a
t e
,
H
a
r d
i s
k
T
y
p
e
…
EXIT WITHOUT SAVING
Selecting the [EXIT WITHOUT SAVING] option allows you to abandon
all data and exit setup, therefore ignoring all your changes.
R
O
O
M
S
P
C
I / I S
A
B
I O
I L I T
I N
S
C
M
S
E
T
U
T
P
U
T
Y
A
W
A
R
D
S
O
F
W
A
R
E
,
C
.
T
Type [Y] to abandon
changes and exit or [N]
to return to the Main
Menu and keep current
values.
S
B
C
P
P
L
T
A
N
D
F
A
E
R
A
D
C
M
E
O
S
S
S
E
T
U
P
P
I N
S
T
E
G
R
A
E
D
P
E
R
I P
S
H
E
R
A
L
S
I O
H
S
T
U
R
S
E
T
U
U
P
E
R
V
I S
O
R
P
A
S
W
O
R
D
I
W
P
O
N
Quit Without Saving (Y/N)? _
O
A
A
L
O
E
F
s
c
:
:
Q
S
u
i t
↑
↓
h
→
←
:
:
S
e
h
le
a
c
t
I t e
m
1
0
a
v
e
&
E
x
i t
S
e
t u
p
( S
D
if t )
F
2
C
n
g
e
C
o
l o
r
T
im
e
,
D
a
t e
,
H
a
r d
i s
k
T
y
p
e
…
48
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-1 SOYO COMBO SETUP
This Motherboard does not use any hardware jumpers to set the CPU
frequency. Instead, CPU settings are software configurable with the BIOS
[SOYO COMBO SETUP].
After the hardware installation is complete, turn the power switch on, then
press the <DEL> key during the system diagnostic checks to enter the
Award BIOS Setup program. The CMOS SETUP UTILITY will display
on screen. Then, select the [SOYO COMBO SETUP] option from the
main menu and press the <Enter> key.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
SOYO COMBO Feature
Auto Detect DIMM/PCI Clk
Spread Spectrum
Enabled
Disabled
Item Help
CPU Host/SDRAM/PCI Clock Default
Menu Level
ꢀ
System Performance
Quick Power On Self Test
Normal
Enabled
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Floppy
HDD-0
LS120
Enabled
ALI OnChip Audio
Enabled
POWER ON Function
xKB Power On Password
xHot Key Power ON
BUTTEN ONLY
Enter
Ctrl-F1
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
The [SOYO COMBO SETUP] menu combines the main parameters that
you need to configure, all in one menu, for a quick setup in BIOS.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
3-1.1 Quick CPU Frequency Setup
Setting
Description
Disabled For EMI test purpose.
Enabled
Auto Detect
DIMM/PCI Clk
Default
Default
Disabled
Spread
Spectrum
Modulated
Enabled
When using Spread Spectrum
Modulated 1.5% or 6% for FCC
or DOC testing.
Default
102/136/34 MHz
CPU Host/
SDRAM/PCI
Clock
This item lists Default
the CPU host
clock and the
PCI bus clock.
It is a read
100/100/33 MHz 105/140/35 MHz
101/101/33 MHz 107/142/35 MHz
102/102/34 MHz 133/133/33 MHz
103/103/34 MHz 136/136/34 MHz
105/105/35 MHz 137/137/34 MHz
107/107/35 MH 140/140/35 MHz
110/110/36 MHz 143/143/35 MHz
100/133/33 MHz 146/146/37 MHz
only item.
Normal
Maximum
Adjust your computer performance. Default
Setting “maximum performance”
may cause your system unstable by
hardware compatibility issue.
System
Performance
3-1.2 Quick Power On Self Test
Setting
Description
Note
Quick Power Disabled
On Self Test
Enabled Provides a fast POST at boot-up. Default
50
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-1.3 System Boot Control Settings
System Boot
Setting
Description
Note
Control Settings
First
/Second/Third
Boot Device
Floppy
LS/ZIP
HDD-0
SCSI
Select Your Boot Device
Priority
CDROM
HDD-1
HDD-2
HDD-3
LAN
Disabled
Disabled
Enabled
Select Your Boot Device
Priority
Boot Other
Device
Default
Default
Enabled
Disabled
This item allows you to
control the onboard AC 97
audio.
ALi OnChip
Audio
3-1.4 Power Management
Setting
Description
Note
Password
Hot key
Enables you to wake-up the
system by entering a password
at the keyboard.
You can wake-up the system by
pressing the key combination of
your choice (Ctrl-F1~F12).
Power On
Function &
KB Power On
& Hot Key
Power On
Mouse Left
Mouse Right
Button only Disables the Wake-Up by
Keyboard function.
Default
Keyboard 98
51
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
STANDARD CMOS SETUP
Select the [STANDARD CMOS SETUP] option from the Main Menu and
press [Enter] key.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Tue, Jan 4 2001
1 : 22 : 12
Item Help
Menu Level
ꢀ
ꢀ IDE Primary Master
ꢀ IDE Primary Slave
ꢀ IDE Secondary Master
ꢀ IDE Secondary Slave
None
None
None
None
Drive A
Drive B
1.44M, 3.5 in.
None
Floppy 3 Mode Support
Disabled
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
Total Memory
640K
64512K
65536K
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
This screen allows you to modify the basic CMOS settings.
After you have completed the changes, press [Esc] key to return to the
Main Menu.
3-1.5 Date & Time
Display
Setting
Please Note
mm/dd/yyyy Type the current date
You can also the
PUp/PDn keys to toggle
Date
hh:mm:ss
Type the current time 24-hour clock format
3:15 PM is displayed as
Time
15:15:00
52
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-1.6 Hard Disks Type & Mode
Choose the type and mode for the hard disks that you have already
installed.
Primary
Setting
Description
Note
(Secondary)
Master & Slave
Press
To auto-detect the HDD’s size,
head… on this channel
IDE HDD
Auto-Detection Enter
Auto
BIOS detects hard disk type
automatically.
User defines the type of hard disk.
Default
Default
IDE Primary
Slave
(User Type)
User
None
Auto
BIOS detects hard disk mode
automatically.
Access Mode
Normal Normal IDE hard disk
<528MB
>528MB
LBA
Enhanced IDE hard disk
Large IDE hard disk (for certain
hard disk)
Large
Note: If you have any questions on your hard disk type or mode, ask
your hard disk provider or previous user for details.
3-1.7 Floppy Drives
Floppy Drives
Setting
Description
Note
360KB, 5.25 in.
1.2MB, 5.25 in.
720KB, 3.5 in.
1.44MB, 3.5 in.
2.88MB, 3.5 in.
None
Drives A & B
Default
Not installed
Disabled
Drive A
Drive B
Both
Default
Floppy 3-Mode
Support
Supports 3-mode
floppy diskette:
740KB/1.2MB/
1.44MB on selected
disk drive.
Special disk drive
commonly used in
Japan
53
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-1.8 Others Optional
Setting
Description
Note
EGA/VGA
CGA 40
Select the video mode.
Default
Video
CGA 80
MONO
(Monochrome)
ALL Errors
No Errors
All, But Keyboard
All, But Diskette
All, But Disk/Key
When the BIOS detects system Default
errors, this function will stop the
system. Select which type of
Halt On
error will cause the system halt.
3-2 ADVANCED BIOS FEATURES
Select the [Advanced BIOS Features] option from the Main Menu and
press [Enter] key.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Advanced BIOS Features
ꢁ
Virus Warning
CPU Internal Cache
External Cache
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Boot Up System Speed
Gate A20 Option
Disabled
Enabled
Enabled
Disabled
Enabled
On
Item Help
Menu Level
ꢀ
High
Fast
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
Disabled
6
250
Setup
OS Select For DRAM > 64MB Non-OS2
Report No FDD For WIN 95
Video BIOS Shadow
No
Enabled
ꢂ
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
54
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
After you have completed the changes, press [Esc] key and follow the
instructions on your screen to save your settings or exit without saving.
3-2.1 Virus Warning
Setting
Description
Note
Disabled Allows you to choose the
Default
Virus Warning
VIRUS Warning feature for
IDE Hard Disk boot sector
protection. If this function is
enabled and someone attempt
to write data into this area,
BIOS will show a warning
message on screen and alarm
beep.
Enabled
3-2.2 Cache Memory Options
Setting
Description
Note
CPU Internal Cache Disabled
Enabled Enables the CPU's internal Default
cache.
Disabled
External Cache
Enabled Enables the external
memory.
Default
3-2.3 Floppy Driver Settings
Setting
Description
Note
Disabled
Enabled
Default
Swap Floppy
Drive
Changes the sequence of A and B
drives.
3-2.4 Boot Up Floppy Seek
Setting
Description
Note
Boot Up Floppy Disabled Seeks disk drives during boot up.
Seek
Disabling speeds boot up.
Enabled
Default
55
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-2.5 Boot Up NumLock Status
Setting
Description
Note
On
Puts numeric keypad in
Default
Boot Up
NumLock
Status
NumLock mode at boot-up.
Puts numeric keypad in arrow key
mode at boot-up.
Off
High
Low
Boots at default CPU speed.
Boots at AT bus speed.
Default
Boot Up System
Speed
3-2.6 Gate A20 Options
Setting
Description
Note
Normal
Fast
Lets chipset control GateA20.
A pin in the keyboard controller Default
controls GateA20.
Gate A20
Options
3-2.7 Typematic Settings
Typematic Settings Setting
Description
Note
Typematic
Rate Setting
Disabled
Enabled
Keystrokes repeat at a rate Default
determined by the
keyboard.
When enabled , the
typematic rate and
typematic delay can be
selected.
The following [Typematic Rate] and [Typematic Delay] fields are active
only if [Typematic Rate Setting] is set to [Enabled]
6 (Char/sec)
8 (Char/sec)
10 (Char/sec)
12 (Char/sec)
15 (Char/sec)
20 (Char/sec)
24 (Char/sec)
30 (Char/sec)
Choose the rate at which a Default
character is repeated when
holding down a key.
Typematic Rate
56
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Typematic Settings Setting
Description
Note
250 (msec)
500 (msec)
750 (msec)
1000 (msec)
Typematic Delay
Choose how long after
you press a key down the
character begins
Default
repeating.
3-2.8 Security Option
Use this feature to prevent unauthorized system boot-up or use of BIOS
Setup. The following table describes the security settings.
Setting
Description
Note
System Each time the system is booted,
the password prompt appears.
Security Option
Setup
If a password is set, the password Default
prompt only appears when you
attempt to enter the BIOS Setup
program.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Description Note
3-2.9 Other Control Options
Other Control Setting
Options
OS Select for
DRAM>64MB
OS2
When using an OS2 operating
system.
Non-OS2 When using another,
non-OS2 operating system.
Default
Report No FDD No
For WIN 95
Windows will release IRQ line 6 Default
(normally used by the Floppy
Disk Drive) after you disable
your on-board FDD and set this
field to [Yes].
Yes
Windows will reserve INT 6 for
your FDD, whether it is disabled
or not.
Disabled
Enabled
Video BIOS
Shadow
Default
The BIOS is shadowed in a 16K segment if it
is enabled and if it has BIOS present.
These 16 segments can be shadowed from
ROM to RAM. BIOS shadow copies BIOS
code from slower ROM to faster RAM. BIOS
can then execute from RAM.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-3 ADVANCED CHIPSET FEATURES
Caution: Change these settings only if you are already familiar
with the Chipset.
The [Advanced Chipset Features] option changes the values of the chipset
registers. These registers control the system options in the computer.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Advanced Chipset Features
ꢁ
DRAM CAS Select
Dram Performance
AT Bus Clock
System BIOS Cacheable
AGP Aperture Size
AGP Delay Offset
AGP Driving Strength
Memory Hole At 15M-16M
I/O Recovery Period
Passive Release
2.5 (DDR) / 3 (SDR)
Normal
CLK2/4
Disabled
128M
Auto
Auto
Disabled
1 us
Disabled
Item Help
Menu Level
ꢀ
ꢂ
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
After you have completed the changes, press [Esc] and follow the
instructions on your screen to save your settings or exit without saving.
The following table describes each field in the Advanced Chipset Features
Menu and how to configure each parameter.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
CHIPSET FEATURES SETUP (Continued)
CHIPSET
Setting
Description
FEATURES
DRAM CAS Auto (By SPD)
When synchronous
DRAM is installed, the
number of clock cycles of
CAS latency depends on
the DRAM timing. Do not
reset this field from the
default value specified by
the system designer.
Select
2.5 (DDR) / 3 (SDR)
2 (DDR) / 2 (SDR)
Default
DARM
Performance
Auto (By SPD)
Failsafe
Slow
This item allow you to
control the DRAM timing.
Normal
Fast
Default
Ultra
Ultra2
7.16 MHz
CLK2/2
CLK2/3
CLK2/4
CLK2/5
CLK2/6
This item allow you to
control the ISA Bus clock.
AT Bus Clock
Default
Default
System BIOS Disabled
Cacheable
Enabled
The ROM area
F0000H-FFFFFH is
cacheable.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
CHIPSET FEATURES SETUP (Continued)
CHIPSET
Setting
Description
FEATURES
128M
Select the size of Accelerated
Graphics Port (AGP) aperture.
The aperture is portion of the
PCI memory address range
dedicated for graphics memory
address space. Host cycles that
hit the aperture range are
Default
AGPAperture
Size
4M, 8M, 16M,
32M, 128M,
256M.
forwarded to the AGP without
any translation.
Auto
+1~+7
- 1~- 7
This item allows you to adjust Default
the AGP delay offset.
AGP Delay
Offset
Auto
Low
Mid
This item allows you to adjust Default
the AGP Driving force.
AGP Driving
Strength
High
Disabled
Enabled
Default
Some interface cards will map
their ROM address to this area.
If this occurs, select [Enabled] in
this field.
Memory Hole
At 15M-16M
1us
2us
3us
This item allows you to control Default
the I/O Recovery Period.
I/O Recovery
Period
Disabled
Enabled
If enabled this item can allow
PCI arbiter to grant to another
PCI master during DMA master
access.
Default
Passive
Release
61
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-4 INTEGRATED PERIPHERALS
Caution: Change these settings only if you are already familiar
with the Chipset.
The [INTEGRATED PERIPHERALS] option changes the values of the
chipset registers. These registers control the system options in the computer.
The following screen shows setup default settings.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Integrated Peripherals
On-Chip Primary IDE
Master PIO
Enabled
Auto
ꢁ
Item Help
Slave PIO
Master Ultra DMA
Slave Ultra DMA
Auto
Auto
Auto
Menu Level
ꢀ
On-Chip Secondary IDE
Master PIO
Enabled
Auto
Slave PIO
Auto
Master Ultra DMA
Slave Ultra DMA
Auto
Auto
On-Chip USB Controller
USB Keyboard Support
Init Display First
Enabled
Disabled
AGP
IDE HDD Block Mode
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Serial Port 3
xUART Mode Select
xRxD , TxD Active
xIR Duplex Mode
xFast IR Mode Use DMA
Onboard Parallel Port
Parallel Port Mode
xECP Mode Use DMA
Enabled
Enabled
3F8/IRQ4
2F8/IRQ3
Disabled
IrDA
Hi, Lo
Half
1
378/IRQ7
SPP
3
ꢂ
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
62
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
The following tables describe each field in the INTEGRATED
PERIPHERALS Menu and provide instructions on how to configure the
IDE controls, FDC controls, and the onboard serial and parallel ports.
3-4.1 IDE Device Controls
IDE Controls
Setting Description
Note
Disabled Turn off the on-board IDE
Enabled Use the on-board IDE
On-Chip PCI IDE
ꢀ Primary
ꢀ Secondary
Default
mode 0-4 0 is the slowest speed
4 is the fastest speed
IDE
ꢀ
ꢀ
ꢀ
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Auto
For better performance and Default
stability, we suggest you use
the Auto setting to set the
ꢀ
Secondary Slave PIO
HDD control timing.
Disabled
Auto
IDE
ꢀPrimary Master UDMA
ꢀPrimary Slave UDMA
ꢀSecondary Master UDMA
ꢀSecondary Slave UDMA
Select Auto to enable Ultra Default
DMA Mode support.
Enabled This should be enabled if
Default
On-Chip USB
Controller
your system has a USB
installed on the system board
and you want to use it. Even
when so equipped, if you
add a higher performance
controller, you will need to
disable this feature.
Disabled
USB Keyboard
Support
Disabled
Default
Enabled Select Enabled if your
system contains a Universal
Serial Bus (USB) controller
and you have a USB
keyboard.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
3-4.2 Keyboard Controls
Keyboard Controls Setting Description
PCI Slot Choose which card – AGP
Display card or PCI VGA card –
Init Display First
AGP
Default
to initialize first.
3-4.3 IDE HDD Block Mode
Setting
Description
Note
Disabled
Enabled
IDE HDD Block Mode
Invokes multi-sector
transfer instead of one
sector per transfer. Not
all HDDs support this
function.
Default
3-4.4 FDD Controls
FDD Controls
Setting
Description
Note
Disabled
Turn off the on-board
floppy controller
Onboard FDC
controller
Enabled
Use the on-board floppy Default
controller
3-4.5 Onboard Serial Ports
Onboard Serial Setting
Ports
Description
Note
Onboard
Disabled
3F8/IRQ4
2F8/IRQ3
Default
(port 3)
Serial Port 1 /
Serial Port 2 /
Serial Port 3
Choose serial port 1 & 2's I/O Default
address.
(port 1)
Default
(port 2)
Do not set port 1 & 2 to the
same address except for
Disabled or Auto.
3E8/IRQ4
2E8/IRQ3
Auto
64
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
IrDA
ASKIR
TFDS6000
HSDL3600
HSDL1100
Default
The second serial port offers
these InfraRed interface
modes.
UART Mode
Select
Hi, Hi
Hi, Lo
Lo, Hi
Lo, Lo
This item allow you to
determine the active RxD,
TxD.
RxD, TxD Active
Default
If [UART Mode Select] is set to [IrDA]/[ASKIR]
Half
Full
Choose [Half] or [Duplex] to Default
set UR2 in half duplex mode
or full duplex mode
IR Duplex Mode
respectively. Refer to your IR
device specifications to select
the suitable mode.
Fast IR Mode
Use DMA
1
3
Default
3-4.6 Onboard Parallel Ports
Onboard Parallel
Ports
Setting
Description
Note
Disabled
Choose the printer I/O
address.
Onboard Parallel
Port
378/IRQ7
3BC/IRQ7
278/IRQ5
Default
EPP 1.9
ECP
ECP+EPP1.9
SPP
The mode depends on your
external device that
connects to this port.
Parallel Port Mode
Default
Default
EPP 1.7
ECP+EPP1.7
3
1
Choose DMA3
Choose DMA1
ECP Mode use
DMA
If [Parallel Port Mode] is set to [EPP] mode
65
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-5 POWER MANAGEMENT SETUP
The [POWER MANAGEMENT SETUP] sets the system's power saving
functions.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Power Management Setup
ACPI Suspend Type
Power Management
PM Control by APM
MODEM Use IRQ
Video Off In Suspend
Video Off Method
S1 (POS)
User Define
No
3
Yes
Item Help
Menu Level
ꢀ
DPMS
PM Timers
HDD Power Down
Suspend Mode
Disabled
Disabled
*** PowerOn \ WakeUp Function ***
Soft-Off by PWR-BTTN
Instant-Off
WakeUp\PowerOn by PCI Card Disabled
USB Dev WakeUp From S3-S5 Disabled
Resume by Alarm
x Date (of Month) Alarm
x Time (hh : mm : ss) Alarm
Disabled
0
0 : 0 : 0
*** Suspend Break Events ***
IRQ[1] ( KeyBoard
IRQ[3]
IRQ[4]
IRQ[5]
IRQ[6] ( Floppy Disk
IRQ[7]
)
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
)
IRQ8J
(
RTC
)
IRQ[9]
IRQ[10]
IRQ[11]
IRQ[12]
IRQ[14]
(
(
PS2 Mouse ) Enabled
Primary IDE ) Enabled
IRQ[15] (Secondary IDE ) Disabled
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
After you have completed the Power Management Setup, press [Esc] to
return to the Main Menu.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
3-5.1 Power Management Controls
Power
Setting
Description
Management
Controls
S1(POS)
S3(STR)
The system will enter the S1
state during suspend. (Low
latency wake up)
Default
Default
ACPI Suspend
Type
Power
Management
User Define Lets you define the HDD and
system power down times.
Doze
timer
Standby Suspend HDD
timer
timer
power
down
Min Saving 1 Hour
Max Saving 1 Min
1 Hour 1 Hour
1 Min 1 Min
15 Min
1 Min
PM Control
by APM
Yes
NO
When enabled, an Advanced
Power Management device will
be activated to enhance the Max.
Power Saving mode and stop the
CPU internal clock. If Advance
Power Management (APM) is
installed on your system,
Default
selecting Yes gives better power
savings.
Video Off
Option
Suspend --> When enabled, this feature
Default
Off
allows the VGA adapter to
operate in a power saving mode.
Always On
All Modes
--> Off
Video Off
Method
V/H
Selects the method by which the Default
Sync+Blank monitor is blanked.
Blank screen
DPMS
67
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Disabled
1-15 Min
Default
Some older
model HDDs
may not support
this advanced
HDD Power
Down
When the set time has
elapsed, BIOS sends a
command to the HDD to
power down. This turns off
the HDD motor.
function.
Disabled
1 Min -
1 Hour
Default
Only an
SL-Enhanced
(or SMI) CPU
can enter this
mode.
Suspend Mode
In Suspend mode, the CPU
stops completely (no
instructions are executed.)
Power Management Controls (Continued)
Power
Setting
Description
Note
Management
Controls
Soft-Off by
PWR-BTTN
Instant-off
Delay 4
Sec.
Default
Turns off the system power 4
seconds after pushing the power
button.
Disabled If enabled any PCI interrupt will Default
Wake up \
Power On by
PCI Card
wake up the system.
Enabled
Disabled An input signal on the serial Ring Default
Wake up \
Power by Ring
Indicator (RI) line (in other words,
an incoming call on the modem)
awakens the system from a soft off
state.
Enabled
USB Dev
Disabled If enabled this item can use A USB Default
Wake up
From S3-S5
device to wake up system from
S3-S5.
Enabled
Disabled The system ignores the alarm.
Default
Resume by
Alarm
Enabled
Set alarm to power on the system
by the date (1-31) or time
(hh:mm:ss). If the date is set to [0],
the system will self-power on by
alarm everyday at the set time.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Enabled
Disabled
Select enabled that will wake up Default
your system when in one of sleep
modes.
IRQ[1]
(Keyboard)
IRQ[3]
IRQ[4]
IRQ[5]
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
Default
Default
Default
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
Enabled
Disabled
Select enabled that will wake up Default
your system when in one of sleep
modes.
IRQ[6]
(floppy Disk)
IRQ[7]
Enabled
Disabled
Select enabled that will wake up Default
your system when in one of sleep
modes.
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
IRQ[8] (RTC)
IRQ[9]
Default
Default
Default
Default
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
IRQ[10]
IRQ[11]
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
Enabled
Disabled
Select enabled that will wake up
your system when in one of sleep
modes.
IRQ[12] (PS2 Enabled
Mouse)
Select enabled that will wake up Default
your system when in one of sleep
modes.
Disabled
69
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Enabled
Disabled
Select enabled that will wake up Default
your system when in one of sleep
modes.
IRQ[14]
Enabled
Disabled
Select enabled that will wake up Default
your system when in one of sleep
modes.
IRQ[15]
(Secondary
IDE)
3-6 PNP/PCI CONFIGURATION SETUP
This option sets the Motherboard's PCI Slots.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
PnP/PCI Configurations
PNP OS Installed
Reset Configuration Data
NO
Disabled
Item Help
Menu Level
ꢀ
Resources Controlled By
x IRQ Resources
Auto (ESCD)
Press Enter
PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB
PCI IRQ Actived By
Disabled
Enabled
Enabled
Level
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
Note: Starred (*) items will disappear when the [Resources
Controlled By] option is set to [Auto].
After you have completed the PCI Slot Configuration, press [Esc] and
follow the instructions on your screen to save your settings or exit without
70
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
saving.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
3-6.1 PNP/PCI Configuration Controls
PNP/PCI
Controls
Setting Description
Yes
No
Set this field to [Yes] if you
PnP OS
Installed
are running Windows 95,
which is PnP compatible.
If the OS you are running
does not support PnP
configuration.
Default
(If there is any
doubt, set this
field to [No])
Disabled Retain PnP configuration
data in BIOS.
Enabled Reset PnP configuration data
in BIOS.
Default
Reset
Configuration
Data
Resources
Controlled By
Manual BIOS does not manage PCI/ISA PnP
card IRQ assignment.
Requires to assign IRQ-# and DMA-# to PCI or
ISA PnP manually.
IRQ-3,4,5,7,9,10,11,12,14,15 assigned to: _
DMA-0,1,3,5,6,7 assigned to: _
Auto
The Plug-and-Play BIOS
Recommended
(ESCD) auto manages PCI/ISA PnP
card IRQ assignment
automatically.
If [Resources Controlled By] is set to [Manual]
IRQ-3,4,5,7,9,1 PCI Device This item allow you to
Default
assign IRQ to PCI
Device or reserved.
1,12,
14,15 assigned
to
Reserved
72
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
PNP/PCI Configuration Setup (Continued)
PNP/PCI
Setup
Setting
Description
Your OS may reassign another interrupt to a PCI slot after BIOS passes control to
the OS, especially if you use Windows 95, 98 or NT.
Disabled Leave this field at Disabled. Default
Enabled
PCI/VGA
Palette
Snoop
Disabled BIOS will assign IRQ for
VGA/USB port.
Assign IRQ
For
VGA/USB
Enabled BIOS won’t assign IRQ for
VGA/USB port.
Default
Default
Edge
This item allow you to
determine which win
ACTIVATE PCI IRQ.
PCI IRQ
Active By
Level
3-6.2 MULTI I/O ADDRESSES
Default settings for multi-I/O addresses are as follows:
Port
I/O Address
378H
IRQ
Status
7
4
3
ECP/EPP
LPT1
COM1
COM2
3F8H
2F8H
Warning: If a default I/O address conflicts with other I/O cards
such as sound card, you must change one of the I/O addresses to
remedy to this address conflict. (I/O addresses can be adjusted from
the BIOS Setup Utility)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-7 PC HEALTH STATUS
This option sets the Motherboard's PC Health Status.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
PC Health Status
CPU Warning Temperature
Current SYS Temperature
Current CPUFAN Speed
Current CHAFAN Speed
Vcore
Disabled
31 º C / 87 º F
4247 RPM
0 RPM
Item Help
Menu Level
ꢀ
1.71 V
+3.3V
3.32 V
+5V
4.92 V
+12V
12.47 V
Shutdown Temperature
75 º C / 167 º F
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
Note: Starred (*) items will disappear when the [Resources
Controlled By] option is set to [Auto].
74
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
Note
3-7.1 CPU Device Monitoring
CPU Device
Monitoring
Setting
Description
CPU Warning
Temperature
Disabled
Default
Set CPU temperature from 50°C
50°C/122°F to 70°C. The CPU will slow
down when CPU temperature
goes beyond the preset value. The
CPU will continue to run slow
until the temperature returns back
within the safe range.
53°C/127°F
56°C/133°F
60°C/140°F
63°C/145°F
66°C/151°F
70°C/158°F
Show the current status of the
system temperature.
Current Sys
Temperature
°C/°F
Current CPU
Temperature
Show the current status of CPU
temperature.
°C/°F
Current
CPUFAN/
CHAFAN
Speed
Show the current status of CPU
Fan.
°C/°F
Show the current voltage status.
Vcore, 2.5V,
3.3V, 5V, 12V
V
Shutdown
Temperature
Set the maximum allowable CPU
temperature, before the system
shutdown.
60°C/140°F
65°C/149°F
70°C/158°F
75°C/167°F
Default
75
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-8 LOAD FAIL-SAFE DEFAULTS
Select the [Load Fail-Safe Defaults] option from the Main Menu to load
the system values you have previously saved. This option is recommended
if you need to reset the system setup and to retrieve the old values.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀSoyo Combo Feature
ꢀPC Health Status
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Pe
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
d
ꢀPower Mana
p
Load Fail - Safe Defaults (Y/N)? Y
ꢀPnP/PCI Con
ng
Esc : Quit
ꢃꢄꢅꢆ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Type [Y] to use the Setup Defaults followed by [Enter] or otherwise [N] to
return to the Main Menu and keep current values.
Warning: If you run into any problem after changing the BIOS
configuration, please load the FAILSAFE DEFAULTS for stable
performance.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-9 LOAD OPTIMIZED DEFAULTS
Select the [Load Optimized Defaults] option from the Main Menu to load
the system values you have previously saved. This option is recommended
if you need to reset the system setup and to retrieve the old values.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀSoyo Combo Feature
ꢀPC Health Status
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Pe
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
d
ꢀPower Mana
p
Load Optimized Defaults (Y/N)? Y
ꢀPnP/PCI Con
ng
Esc : Quit
ꢃꢄꢅꢆ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Type [Y] to use the Setup Defaults followed by [Enter] or otherwise [N] to
return to the Main Menu and keep current values.
Warning: If you run into any problem after changing the BIOS
configuration, please load the FAILSAFE DEFAULTS for stable
performance.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-10 SUPERVISOR PASSWORD
Based on the setting you have made in the [Security Option] of the [BIOS
FEATURES SETUP] section, the password prevents access to the system
or the setup program by unauthorized users. Follow this procedure to set a
new password or disable the password:
1. Choose [BIOS FEATURES SETUP] in the Main Menu and press
[Enter]. Select the [Security Options] item and set the field to:
a. [System]: The password is required every time the system is
booted. This means only a person who knows the password can
use this computer.
b. [Setup]: The password is required only when you attempt to
enter the BIOS Setup program.
2. Choose [SUPERVISOR PASSWORD] from the Main Menu and
press [Enter]. The following prompt appear:
Enter Password:
Warning: If you forget or lose the password, the only way to
access the system is to set jumper JP5 to clear the CMOS RAM.
All setup information is lost and you must run the BIOS setup
program again.
Note: If you do not wish to use the password function, press
[Enter] directly and the following message appears:
Password Disabled!!
78
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3. Enter your new password and press [Enter]. The following message
appears, prompting to confirm the new password:
Confirm Password:
4. Re-enter your password and then press [Enter] to exit to the Main
Menu.
This diagram outlines the password selection procedure:
Type the Password
Press <Enter> without
ROM PCI/ISA BIO
and Press: <Enter>
entering the password
CMOS SETUP UTIL
AWARD SOFTWARE,
PASSWORD
Enter Password:
BIOS FEATURS SE
C
Enter Password:
Password Disabled!!
∗∗∗∗∗
P
SAVE & EXIT SETUP
Confirm Password:
∗∗∗∗∗
EXIT WITHOUT SAVING
After you confirm the password,
Esc : Quit
m
press <Esc> to exit
F10 : Save & Ex
olor
Time, Date, Hard Disk Type…
3-11 USER PASSWORD
When the user password option is on, you are not allowed to change any
setting in the [CMOS SETUP UTILITY] except for changing the user's
password.
The password setting procedure is similar to that for the [SUPERVISOR
PASSWORD] (Refer to section 3-9).
79
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-12 IDE HDD AUTO DETECTION
This Main Menu function automatically detects the hard disk type and
configures the [Standard CMOS Features] accordingly.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
IDE Primary Master
IDE HDD Auto-Detection
IDE Primary Master
Press Enter
Auto
Item Help
Menu Level
ꢀ
Capacity
0 MB
Access Mode
Auto
0
0
0
0
0
Cylinder
Head
Precomp
Landing Zone
Sector
0
ꢃꢄꢅꢆ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
Note: This function is only valid for IDE type of hard disk drives.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7ADA V1.0
3-13 BOOT MENU
Boot Menu enables user to boot-up on different boot device without going into the BIOS
setup.
To enable boot Menu, press “ESC” after memory initialization, user will
see a device menu, in which user can choose the device they wish to boot
from.
Boot Menu
== Select a Boot First device ==
Floppy
Ls120
HDD-0
SCSI
CDROM
HDD-1
HDD-2
HDD-3
ZIP100
LAN
:Move ENTER:Accept F4:Exit
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
Chapter 4
DRIVER INSTALLATION
Your SY-K7ADA V1.0 Motherboard comes with a CD-ROM labeled
"SOYO CD." The SOYO CD contains the user's manual file for your new
Motherboard, the drivers software available for installation, and a database
in HTML format with information on SOYO Motherboards and other
products.
Step 1. Insert the SOYO CD into the CD-ROM drive
If you use Windows NT, the SOYO-CD will not detect your motherboard
type. In that case the following dialog will pop up, please choose your
motherboard and press OK. Now the SOYO-CD Start Up Menu will be
shown.
X
Please Select Your Board
LI-7000
7IWB
7IWA-F
7IWA-F V1.0
6IWM/L
6IWM
7IWB V1.0
7IWM
6IWA
7IWM/L V1
Cancel
OK
(SOYO CD Start Up Program Menu)
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
If you use Windows 95 or 98, the SOYO CD Start Up Program
automatically detects which SOYO Motherboard you own and displays the
corresponding model name.
The user's manual files included on the SOYO CD are in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat
Reader software must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader
utility is already present in your system, and otherwise prompts you on
whether or not you want to install it. You must install the Acrobat Reader
utility to be able to read the user's manual file. Follow the instructions on
your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
Step 2. Install Drivers
Click the Install Drivers button to display the list of drivers software that
can be installed with your Motherboard. The Start Up program displays
the drivers available for the particular model of Motherboard you own. We
recommend that you only install those drivers.
driver
revision:
ALi AGP Driver for win 9x/2000/XP
ALi Onboard Audio Driver for win 98/98SE/ME/2000/XP
ALi Onboard Audio Driver for win NT4.0
ALi Hardware monitor Driver for win 9x/ME
ALi Hardware monitor Driver for win NT/2000/XP
Cancel
OK
(Driver Installation Menu)
A short description of all available drivers follows:
ꢀ ALi AGP driver for Win 9x/2000/XP
The ALi AGP driver package includes all drivers your motherboard needs.
After selecting this driver package, one driver will be installed
automatically. A description of the 2 drivers follows:
ALi IDE Driver
This driver will speed up the data-transfer rate to and from the
harddisk.
ALi AGP Driver
This driver must be installed in order to be able to make use of the
on-board AGP Video functionality.
ꢀ
ALi Audio Accelerator Driver for Win 98/98SE/ME/2000/XP
You have to install the drivers before installing any application for the
Audio Accelerator.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
ꢀ ALi Audio Accelerator Driver for Win NT4.0
You have to install the drivers before installing any application for the
Audio Accelerator.
ꢀ ALi hardware monitor for Win 9x/ME
Your motherboard comes with a hardware monitoring IC. By installing
this utility Temperature, Fan speed and Voltages can be monitored. It is
also possible to set alarms when current system values exceed or fall
below pre-set values.
ꢀ ALi hardware monitor for Win NT/2000/XP
Your motherboard comes with a hardware monitoring IC. By installing
this utility Temperature, Fan speed and Voltages can be monitored. It is
also possible to set alarms when current system values exceed or fall
below pre-set values.
Select which driver you want to install and click OK, or click Cancel to
abort the driver installation and return to the main menu.
Note: Once you have selected a driver, the system will automatically exit
the SOYO CD to begin the driver installation program. When the
installation is complete, most drivers require to restart your system before
they can become active.
Step 3. Select which driver you want to install and click OK
Notice 1: Once you have selected a driver, the system will automatically exit
the SOYO CD to begin the driver installation program. When the
installation is complete, most drivers require to restart your system
before they can become active.
Notice 2: You may click Cancel to abort the driver installation and return to
the main menu.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
Step 4.
1.For supporting S3 mode wake up function in WINDOWS 98se, please
download
the driver from SOYO web site (www.soyo.com.tw).
Please put this downloaded driver in c:\windows\system32\driver and
remove USB
device in “Device Manager” then refresh.
Please put this downloaded driver in c:\windows\system32\driver
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
Remove USB device(ex : USB keyboard, mouse,…,etc.)
Refresh
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers installation
SY-K7ADA V1.0
Final
2.If customer uses the WINDOWS 95 OSR2, please use the NT version
driver when installing audio driver.
3.Right now, ALI chipset does not support ATI RAGE 128 graphics chip,
so K7ADA V1.0 can not support this kind of VGA card.
Step 5. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to
automatically find the latest BIOS, manual and driver releases for your
motherboard. This button will only work if your computer is connected to
the internet through a network or modem connection. Make sure to get
your modem connection up before clicking this button.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Server Technology Server 01621 REVC 100605 User Manual
Sony Cassette Player CFD Z501 User Manual
Sony Projection Television KWP 65HD1 User Manual
Sony Universal Remote KLV 23 User Manual
Sparky Group Drill BUR 131E User Manual
Star Manufacturing Toaster QCSe3 1300 User Manual
Sterling Saw D48160s User Manual
Summit Freezer AL 650 User Manual
Symphonic TV VCR Combo WF319E User Manual
Tanaka Trimmer TBC 4000 User Manual