Universal Tilting TV Mount - 32" to 60"
Installation Instructions
Tiltable LCD / TFT TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32" - 60"
Tilt: 0 / +15 degrees
Maximum load capacity: 165 lbs / 75 kgs
Wall distance: 3.3" / 84mm
Bubble level included
Universal Mounting Pattern
IMPORTANT: If you don't understand the installation instructions, please
consult an installation specialist
04-0529D
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
1. Please ensure that the bubble level (L-2) is properly attached to the
wall plate prior to mounting.
2. Please check the two rails before installing, if without the
knob, please detach the screw and install the knob.
Step 1: Wall plate installation
A) Wood Stud Installation
NOTE: For secure wood stud mounting, the wall plate must be mounted to two studs at least
16" apart.
1
Use a high-quality electronic stud finder (commercially available)
to locate two adjacent studs and mark their locations with a
pencil (1-a).
2
Attach the bubble level (L-2) to the wall plate and with the help of
an assistant ensure the wall plate is level, position the wall plate
against the wall in the desired mounting location (figure 1-b).
3
Mark the right (upper and lower) and the left (upper and lower)
positions of the small horizontal slots that are in alignment with
the studs.
4
5
You should mark four positions total.
Pre-drill a /16" hole to a depth of 3" in the wall stud at each
marked location.
6
Position the wall plate against the wall and line up the mounting
slots with the drilled holes. Check the bubble level to verify that
the wall plate is level.
7
8
For each location, insert a lag bolt (J) and washer (L-1) into the
wall (figure 1-c).
Tighten each bolt with an open ended socket wrench by turning clockwise until tight.
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive
torque.
Do not release the wall plate until it is properly mounted and secured to the wall.
CAUTION:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
B) Concrete/Brick Installation
NOTE: The concrete anchors must be used for concrete installation.
1
Attach the bubble level (L-2) to the wall plate, with the help of an
assistant place the wall plate into position against the wall, using
the bubble level to keep it level.
2
3
Mark four holes to be used for securing the mount and place the
wall plate aside (figure 1-d).
Drill holes using an electric drill and 1/2" masonry bit to a depth of
3".
4
5
Insert a concrete anchor (K) into to each hole.
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush
with the wall.
6
7
Once all of the anchors are in place, move the wall plate back into position. Check the bubble
level to verify that the wall plate is level.
Insert bolt (J) with washer (L-1) into each concrete anchor in the wall. Do not tighten until all
screws are in place.
Step 2 Display Bracket Installation
1
To ensure optimal installation, this kit includes various screws of
different diameters and lengths.
2
Place your TV screen down on a soft, flat surface, and locate the
threaded mounting points that are located on the back of the
display.
3
4
5
Determine which screw (A/B/C/D/E/F/G/H) is of the correct length
by carefully inserting a straw, or toothpick, and mark how deep
the mounting point is.
According to the size of display's hole, choose the corresponding
screw and hole on the rectangle washer, then thread them in line
as shown (figure 2-a).
If your display has a curved back or a recessed thread mounting
point, place the spacer (M) between the mounting bracket and
display and then choose screw (F/G/H) to match (figure 2-b).
Step 3 Final Installation & Adjustment
1
Hook the TV rails over the top of wall plate (3-a).
2
The TV rail can be tilted down up to 15 degrees. To make this adjustment, first loosen the knob and pull or
push the rail until it is in the desired position. Once the desired level of tilt is achieved, re-tighten the mount by
turning the tension knobs (figure 3-b).
3
4
On the TV rail equipped with lock, lock it to avoid the theft by rotating the key until the hook touches the bottom
bar of the wall plate (3-c)
On the TV rail equipped with screw, rotate the long screw at the bottom of the display rail to tighten it & secure
mount (figure 3-d).
Maintenance
Check the mounting screws every two months for tightness.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online
support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks
away. You can also submit questions online and a technical support analysts will promptly respond.
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the original purchaser and guarantees
the product to be free of any defects in materials or workmanship for five (5) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the
product if defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or
replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then click RMA to submit a request to SIIG RMA or fax a request to 510-657-5962. If the
product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original
package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping the product to SIIG. Ship the product to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #: ________________
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no
cost to the customer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra
ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between
Desktop/Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage
connectivity solutions to our extensive portfolio. All centered around the distribution and switching of A/V signals
over CAT5/6, these products include matrix switches, distribution amplifiers, extenders, converters, splitters,
cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while
keeping economical and competitive prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive user manuals, user-friendly features,
and most products are backed by a lifetime warranty.
SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the
Americas, as well as through major distributors, system integrators, and VARs.
PRODUCT NAME
Universal Tilting TV Mount - 32" to 60"
Universal Tilting TV Mount - 32" to 60" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other
names used in this publication are for identification only and may be trademarks of their respective owners.
November, 2010
Copyright © 2010 by SIIG, Inc. All rights reserved.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|