Satellite Speaker
Mounts - 1 Pair
Quick Installation Guide
Introducing the Satellite Speaker
The Satellite Speaker Mounts - 1 Pair are fully-adjustable
(Tilt, Swivel, & Pivot) speaker wall or ceiling mounts.
KeyFeaturesandBenefits
•
•
Universaldesign fits most speaker brands &designs
Ceiling or wall mountable & compatible with 1, 2,
or 4-hole and key-hole speaker mounting (with
included adapters)
•
•
Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning
Holds speakers weighing up to 8 lbs
Serial Number Sticker
For future product return or exchange, this serial number
is required. Please keep it for your reference.
04-0600A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Please read the instructions prior to installation. This
speaker mount is designed solely for the mounting of
small speakers weighing less than 8lbs. We are not
responsible for damage that may occur if speakers
weighing more than 8lbs. are used.
Theuser willhaveto determinewhich typeofconfiguration
will work best with the included mounting hardware. If
the included hardware does not fit with the application,
the appropriate hardware will have to be purchased.
Single Hole Mounting
1.
Most satellite speakers will require the use of the
M5 x 20mm machine screw used in combination
with M5 x 1/ 8" plastic washer. The plastic washer
is used as a spacer between the threaded insert and
the post, see Figure 1 below. It is critical the plastic
washer is used correctly.
M5 x 20mm
Machine Screw
Back Speaker
Mounting Post
M5 x 1/ 8"
Plastic Washer
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Once the proper configuration is determined,secure
the post to the speaker.
Some speakers use the smaller M4 x 8 screw, which
is inserted into the off-center on the mounting post,
see Figure 2 below.
M4 x 8mm Flat Head
Machine Screw
Back Speaker
Figure 2
4.
Check the size of the hole, make sure you have the
5/ 8"-32 x 5/ 8" machine screw, the 1/ 4"-20 x 1/ 2"
machine screw, the M6 x 20mm, or the M5 x 20mm
fits inside, see Figure 3 below.
M5 x 1/ 8" Plastic Washer
Back Speaker
5/ 8"-32x5/ 8" Machine Screw
1/ 4"-20 x 1/ 2" Machine Screw
Figure 3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5.
When the correct size is determined, place the
screw through the speaker post and attach to the
rear of the speaker enclosure. If the screw does not
tighten properly, use the M5 x 1/ 8" plastic washer
to tighten it up.
Key Hole Mounting
1.
If your speaker has a factory key hole design, you
will use the 5/ 8"-32 x 5/ 8" machine screws in
combination with the key hole nut.
2.
Loosely pre-assemble the mounting post with the
5/ 8"-32 x 5/ 8" machine screw and key hole nut, see
Figure 4 below. Be sure the key hole nut is installed
with the knurled (rough) edge toward the host.
Mounting Post
Keyhole
M5 x 1/ 8"
Plastic Washer
5/ 8"-32x5/ 8"
Back Speaker
Machine Screw
5/ 8"-32x5/ 8"
Machine Screw
Figure 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Engage the key hole nut into the key hole slot.
Put tension on the assembly by gently pulling back
on the speaker mount post while tightening the
5/ 8"-32 x 5/ 8" machine screw, see Figure 4 on page
5.
5.
6.
The key hole nut will engage on the housing in the
key hole slot.
If the post does not tighten securely against the
housing, it will be necessarry to use the M5 x 1/ 8"
plastic washer as a spacer under the head of the
5/ 8"-32 x 5/ 8" machine screw, see Figure 4 on page
5.
2/4 Hole Mounting
1.
Find the best mounting configuration that matches
your speaker enclosure. Four-hole mount patterns
can be accomodated by positioning the speaker
plate diagonally, see Figure 5 on the next page.
2.
Using the 1/ 4"-20x 1/ 2"machine screws,installthe
speaker plate and secure the speaker enclosure, see
Figure 5 on the next page.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Back
1/ 4"-20 x 1/ 2"
Machine Screw
Speaker
4-Hole
Orientation
2-Hole Orientation
Figure 5
Self-TappedMounting
1.
Locate the optimum location for the mounting
plate and use it as template to mark the drilling
locations. Do not drill or screw into the speaker
where you could possibly damage the internal
components.
2.
Drill the pilot hole(s) using a 1/ 8" drill bit. The
holes(s)should not be drilled more than 1/ 2"depth,
see Figure 6 on the next page.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ST5.5 x 19 Self
Tapping Screw
Back Speaker
Figure 6
Mounting to the Wall or Ceiling
The mounting hardware for the three different surface
applications is supplied. You will need to determine what
style hardware willwork best with your mounting surface.
Always use caution when drilling into a wall or ceiling.
Make sure to avoid all electrical and water lines.
WoodSurface
1.
Using a stud finder,locate the wood stud or framing
member. Always mount the speakers in the center
of a stud.
2.
Using the wall plate as a template, mark hole
positions on mounting surface. For in-w all
applications,position themounting holesin a vertical
pattern, see Figure 7 on the next page.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ST5.5 c 45 Self
Tapping Screw
Figure 7
3.
4.
Drill holes through the drywall and into the wood
stud using a 1/ 8" drill bit. These holes should be
drilled 1-7/ 8" deep, see Figure 7 above.
After the holes are drilled, mount the wall plate
using the self tapping screws.
DrywallSurfaces
1.
Locate the best mounting location in the ceiling or
wall. Using the wall plate as a template, mark the
hole positions on the mounting surface. For in-wall
applications,position themounting holesin a vertical
pattern, see Figure 8 on the next page.
2.
3.
Drill holes in the drywall using a 5/ 16" drill bit.
Once the holes are drilled,insert the alligator anchor
into the holes. Make sure the anchor is flush with
the wall and/ or ceiling surface, see Figure 8 on the
next page.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
With the anchors in place, mount the wall plates
using the ST5.5 x 45 self tapping screws, see
Figure 8 below.
ST5.5 x 45 Self
Pre Drill 5/ 16"
Holes
Tapping Screw
Insert screw through wall plate
and into the alligator anchor
Insert Alligator
Anchor
Figure 8
ConcreteSurface
1.
Using the wall plate as a template, mark hole
positions on the mounting surface. For in-wall
applications,position themounting holesin a vertical
pattern, see Figure 9 on the next page.
2.
Drill holes in the solid concrete or hollow block
using a 5/ 16" masonry bit. Once the holes are
drilled, insert the # 12-14 alligator anchors into the
holes and make sure the anchor is flush with the
surface of the wall, see Figure 9 on the next page.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert Alligator
Anchor
ST5.5 x 45 Self
Tapping Screw
Insert screw through wall plate
and into the alligator anchor
Using the hammer to
tap anchor into place
Figure 9
3.
With the wall anchor in place, mount the wall plate
using the ST5.5 x 45 self tapping screws, see
Figure 9 above.
ExtensionMounting
This is for ceiling and/ or shelf applications. Do not use
extension in the wall application.
1.
Install 2-1/ 2" extension portion of the speaker
mount to the wall place.
2.
Secure the setscrew to hold the extension in place
with the weight of the speaker attached.
Tighten the allen screw using
the provided allen wrench
Figure 10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Low-ProfileMounting
This is for wall and ceiling application.
1.
Installthe low-profile portion ofthe speaker mount
to the wall plate or 2-1/ 2" extension.
2.
Secure the setscrew to hold the extension in place
with the weight of the speaker attached.
Tighten the allen screw using
the provided allen wrench.
Figure 11
SpeakerMounting
1.
Install the speaker with the speaker post or 2-hole
plate attached.
2.
Secure the screw to hold the extension in place with
the weight of the speaker attached
Post Style Speaker
2-Hole Speaker
Figure 12
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Blank Page
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily
with new drivers and solutions. Answers to your questions could be just a few
clicks away. You can also submit questions online and a technical support
analysts will promptly respond.
SIIG offers a 5-year manufacturer warranty with this product. Please see our web
site for more warranty details. Ifyou encounter any problems with this product,
please follow the procedures below.
Ifit is within the store's return policy period,please return the product to the store
where you purchased from. Ifyour purchase has passed the store's return policy
period, please follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to w w w .siig.com , click Su p p ort, th en RM A to su bm it
a
request to SIIG RMA. Your RMA request will be processed, ifthe product is
determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•
Properly pack the product for shipping. All accessories that came with
the original package must be included.
•
Clearly write your RMA number on the top ofthe returned package. SIIG
will refuse to accept any shipping package, and will not be responsible
for a product returned without an RMA number posted on the outside of
the shipping carton.
•
•
You are responsible for the cost of shipping. Ship the product to the
following address:
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
SIIG w ill ship the repaired or replaced prod uct via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985,SIIG,Inc.is a leading computer upgrade manufacturer ofI/ O
connectivity products,including PCI&ISA serialand parallelports,USB,Serial
ATA & UltraATA controllers, FireWire (1394a/ b), networking, sound cards,
and other accessories. SIIG is the premier one-stop source ofupgrades.
SIIG products offer comprehensive user manuals,many user-friendly features,
and are backed by an extensive manufacturer warranty. High-quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one ofthe lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
through major distributors, system integrators, and VARs in the Americas and
the UK,and through e-commerce sites.
PRODUCT NAME
Satellite Speaker Mounts - 1 Pair
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
Satellite Speaker Mounts - 1 Pair is a trademark of SIIG, Inc. SIIG and the SIIG logo are
registered trademarksofSIIG,Inc. Other namesused in thispublication arefor identification
only and may be trademarks of their respective companies.
November, 2009
Copyright © 2009 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|