DP SoundWave 5.1 PCIe
Quick Installation Guide
Introducing the DP SoundWave 5.1 PCIe
The DP SoundWave 5.1 PCIe transforms your computer
intoahigh-definition5.1channelsurroundsoundhome
theater system.
KeyFeaturesandBenefits
•
•
•
Provides high definition 5.1 channel surround
sound
Supports 24-bit/96kHz digital and 20-bit/48kHz
analog connections
Supports Dolby Digital/Dolby Digital EX
surround sound, EAX 1.0, 2.0, A3D 1.0 and
DirectSound 3D
•
HRTF-based 3D positional audio, supporting
DirectSound and A3D interface
•
•
Provides S/PDIF Digital output (Toslink)
Perfect audio upgrade for DVD playback, MP3 or
other music, gaming and more
SystemRequirements
•
PCI Express enabled system with an available PCI
Express slot
Windows® 7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit)
•
04-0631A
Download from Www.Somanuals.com. All Manuals Search And Download.
1
AudioConnectors
MIC
This connector provides microphone-in function.
LINE In
This connector provides analog line-in function.
Digital Out (Toslink)
Connect to digital input of an external audio device via
Digital S/PDIF optical cable (cable not included).
CD-In (J3, J5)
Analog CD-In, connect to CD-ROM or DVD-ROM via
audio cable (cable not included).
Aux-In (J7)
Connect to audio output device via audio cable (cable
not included).
Front Out (green)
This connector provides front audio output, or you can
connect one set of stereo speakers.
Surround(black)
This connector provides rear surround sound output.
Center/Subwoofer Out (yellow)
This connector provides center and subwoofer (LFE)
audio output.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
Note: For low profile systems, replace the currently
mounted bracket with the included low profile bracket.
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer.
2. Unplug the power cord and remove the computer
cover.
3. Remove the slot bracket from an available PCIe
slot.
4. Carefully align the card to the selected PCIe slot,
push the board down firmly, but gently, until it is
well seated.
5. Replace the slot bracket holding screw to secure
the card.
6. Connect one end of the audio cable from your
CD/DVD-ROM to the CD-In on the soundcard.
7. Replace the computer cover and reconnect the
power cord.
8. Make your speaker and device connections, then
complete the driver installation on the next pages.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Installation
Windows7(32-/64-bit)
1. Install the board, then boot up Windows.
2. At the Windows desktop insert the driver CD.
3. AttheCDAutoPlaybox, clickOpenfoldertoview
files.
4. Double click Setup (Application).
5. Follow the on screen instructions to complete the
installation.
WindowsVista(32-/64-bit)
1. Install the board, boot up Windows.
2. At Found New Hardware, click Cancel.
3.
Insert the software CD.
At the CD Auto Play window: click Open folder to
view files. Double click Setup (Application).
IfCDAutoPlaydoesn'tstart:clickStart,intheStart
Search box, type D:\setup.exe, press Enter.
(Change D: to match your CD/DVD-ROM drive
letter)
4. Follow the on screen instructions to complete the
installation.
WindowsXP(32-/64-bit)
1. Install the board, boot up Windows.
2. AttheFoundNewHardwareWizard,clickCancel.
3. Insert the software CD. Click Start, Run, type
D:\Setup.exe, then click OK. (Change D: to match
your CD/DVD-ROM drive letter)
4. Follow the on screen instructions to complete the
installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WindowsServer2003&2008(32-/64-bit)
1. Install the board, boot up Windows.
2. At Found New Hardware..., click Cancel.
3. Insert the driver CD.
At the CD Auto Play window: click Open folder to
view files. Double click Setup (Application).
IfCDAutoPlaydoesn'tstart:clickStart,intheStart
Search box, type D:\setup.exe, press Enter.
(Change D: to match your CD/DVD-ROM drive
letter)
4. Follow the on screen instructions to complete the
installation.
ToVerifyWindowsInstallation
1. Check Device Manager to verify installation.
Windows 7: Right click Computer, click Manage,
then click Device Manager.
Windows Vista: Right click Computer, click
Manage, click Continue, then click Device
Manager.
Windows XP / Server 2003: Right click My
Computer, click Manage, then click Device
Manager.
Windows Server 2008: Right click Computer, click
Manage, double click Diagnostics, then click
Device Manager.
2. Double click Sound, video and game controllers,
Envy24 Family Audio Controller WDM should
be displayed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Uninstalling the Soundcard Driver
If you want to uninstall the driver from the system, it's
best to do so before removing the card from the system.
Use the same setup program that you used when
installing the driver, however, at the appropriate time
selecttheUninstallDeviceDriveroptionandfollowthe
on screen instructions to uninstall the driver.
Enable Windows Audio
Windows XP, Server 2003 and Server 2008 systems that
do not have a fully operating sound card may require
enabling Windows Audio support to support the DP
SoundWave 5.1 PCIe.
Windows XP / Server 2003 & 2008
1. Click Start, Control Panel, Sounds and Audio
Devices.
2. At the Sounds and Audio Devices Properties box
check Enable Windows Audio, then click OK.
3. Click Yes to restart Windows.
Sounds and Multimedia Properties Audio
Configuration
Windows7
1. Click Start, Control Panel.
2. Click Hardware and sound icon.
3. Click Manage audio devices.
4. Select the Playback tab, right click Envy24 Family
AudioControllerWDM,clickSetasdefaultdevice.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WindowsVista
1. Click Start, Control Panel.
2. Click Classic View, double click the Sound icon.
3. At Playback tab, select Envy24 Family Audio
Controller, click Set as default device.
Windows XP / Server 2003 & 2008
1. Click the Start button.
2. Click Control Panel, Sounds and Audio Devices.
3.
Click the Audio tab.
4. In the Sound Playback and Sound Recording drop
downbox,selectEnvy24FamilyAudioController
WDM.
5. Click OK to save the changes.
Enable Digital CD Playback
Windows XP / Server 2003 / 2008
1. Right click My Computer, click Manage, then
click Device Manager.
2. Double-click DVD/CD-ROM drives, then double
click your DVD or CD-ROM drive, then click the
Properties tab.
3. Check Enable digital CD Audio for this
CD-ROM device, then click OK.
4. If prompted, restart Windows. Otherwise, your
drive is ready for use.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Deck
Audio Deck is an easy to use, full featured audio utility
that allows you to adjust audio outputs, recording,
sound effects and surround sound support to match
your taste and mood.
QuickStartIcon
During driver installation, the Audio Deck quick start
icon is placed in the taskbar by the system clock. Click
on the icon to open the Audio Deck Control Panel.
ControlPanel
S/PDIF Control
Close
Speaker
Playback
Recording
Master Volume
Control
Sound Effects
KalaOK
Advanced Controls
Information
Stereo Link
Mute
Change Channel
•
S/PDIFControl:SetsDigitaloutput(Toslink)signal
source
•
•
Speaker: Sets the volume for the various speakers
Playback:Adjuststhevolumeofeachoutputdevice
9
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Recording: Selects the recording source and
controls it's recording level
Sound Effects: Includes Equalizer with 4 presets
and you can customize your own settings,
QXpander, Environments. This tab appears only
after selecting Immezio 3D Effects Enable in the
Advanced Controls window. Important: Sound
Effects not supported in Windows XP (64-bit) and
Windows Server 2003 (64-bit).
•
•
•
•
KalaOK: Adjusts mid-range sound volume -
Karaoke enhancement
Advanced Controls: Sets sound parameters for the
soundcard
Information: System and driver information is
displayed here
Change Channel: Displays the current channel
mode. Click any button to access Channel Setup to
change channel mode. Note: 4-channel mode is
supported in XP and Windows Server 2003.
•
•
•
•
Master Volume Control: Adjusts the system
volume of the left and right channels
Stereo Link: Adjusts the left and right channels
individually
Mute: Turns the system sound On/Off
immediately
Close: Click to close the Control Panel
10
Download from Www.Somanuals.com. All Manuals Search And Download.
S/PDIFControl
•
•
S/PDIF Out Enable: Turns ON/OFF the Optical
Digital Out
AC3 or PCM auto select (48kHz): With this setting
all of the digital sources (wave, midi) are played
over the digital output. This setting is also used
whenyouwanttosendencodedAC3streamstoan
external decoder
•
•
AC3 Only (48 kHz): This setting is only used when
you want to send encoded AC3 streams to an
external encoder.
PCM Only: This setting is only for digital sources
(wave,MIDI),whichareplayedoverdigitaloutput
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker
Here you can set the volume for the various speakers.
All speakers can be muted by clicking the check button
above the speaker icon.
Playback
Here you can adjust the playback settings for various
resources.
Next Page
•
•
Wave: Sets the volume for WAV sound (WAV,
MP3, WMA)
SW Synth: Sets the volume for MIDI sound from
software synthesizer
12
Download from Www.Somanuals.com. All Manuals Search And Download.
•
CD Player: Sets the volume for analog output of
the CD/DVD-ROM
•
•
MIC: Sets the volume for microphone playback
Line In: Sets the volume for analog playback of
LineInsound(noplaybackthroughDigitalOptical
Out)
•
•
CD In: Sets the volume for analog output of CD In
Wave Table: Sets the volume for MIDI sound from
wavetable daughter board (not included)
•
•
Aux: Sets the playback volume for Aux In
PCM SPDIF: Sets the volume for S/PDIF Out
Recording
In the recording menu you can choose which source the
sound card will use to record.
Source Column
•
•
•
SourceColumn:Setthevolumeforrecordingsignal
which the user has selected
DCRemove:Reducesinterference whenrecording
through the microphone.
20dB boost: Increases the sensitivity of the
microphone by 20dB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundEffects
This panel is enable by selecting Immezio 3D Effect
EnableinAdvancedControls. Note:NotsupportedinXP
(64-bit) & Server 2003 (64-bit).
•
•
Equalizer: Set the volume of different frequencies
independently
Preset: Select from the pre-configured equalizer
settings
•
•
QXpander: Adjusting the sound expanding effect
Environmental Modeling: Select different
environment effect models
KalaOK
KalaOK: Adjusts volume of mid-range sounds.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
AdvancedControls
In the advanced controls menu you can set system
parameters for the DP SoundWave 5.1 PCIe.
•
•
Language: Select Auto, English or Chinese
Center/LFE Swap: Swap center speaker and sub-
woofer speaker outputs
•
•
Stereo Expander: This setting duplicates the front
channel stereo sound to the other surround sound
channels
Emmezio 3D Effects Enable: Offers 3D audio for
computer games or musical playback in
multi-channel mode. Note: Immezio 3D Effects not
supportedinWindowsXP(64-bit)andWindowsServer
2003(64-bit).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SpeakerTest
Channel Setup
Speaker Test
•
•
Speaker Test: Tests the position of your 2, 4 or 6
channel speaker system. Click on a speaker icon
and you will hear a short note. Speaker test works
with speakers connected into the G9 DIN audio
connector only. Speaker Test not intended for
Optical S/PDIF or surround sound speakers
operating through a digital decoder box
Channel Setup: Click on the desired icon to change
the speaker mode. The active mode will display to
the left of the menu.
Information
System and driver information is displayed here.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’sOnlineSupporthasanswers! Simplyvisitour
databaseisupdateddailywithnewdriversandsolutions. Answers
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffersa5-yearmanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased it.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
requesttoSIIGRMA. YourRMArequestwillbeprocessed,ifthe
product is determined to be defective, an RMA number will be
issued.
Step 2: After obtaining an RMA number, ship the product.
• Properlypacktheproductforshipping. Allsoftware,cable(s)
andanyotheraccessoriesthatcamewiththeoriginalpackage
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIGwillrefusetoacceptanyshippingpackage,and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• Youareresponsibleforthecostofshipping. Shiptheproduct
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA#:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions(includingSerialATAandUltraATAControllers,FireWire,USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V
signalsoverCAT5/6,theseproductsincludematrixswitches,distribution
amplifiers, extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providinghighqualityproductswhilekeepingeconomicalandcompetitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
PRODUCT NAME
DP SoundWave 5.1 PCIe
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
DPSoundWave5.1PCIeisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarks
ofSIIG,Inc. MicrosoftandWindowsareregisteredtrademarksofMicrosoftCorporation. Allother
namesusedinthispublicationareforidentificationonlyandmaybetrademarksoftheirrespective
owners.
May, 2010
Copyright © 2010 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|