Hi-Speed USB 5-Port PCI
Quick Installation Guide
FeaturesandBenefits
•
•
•
Compliant with USB specifications revision 2.0
Conforms to PCI specifications revision 2.2
Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
•
•
Supports high-speed (480 Mbps), full-speed (12
Mbps), and low-speed (1.5 Mbps) data transfer
modes
User friendly hot-swapping feature allows you to
attach/removeUSBdeviceswithouturningoffyour
system
Note: USB 1.1 devices are limited to USB 1.1 speeds
evenwhentheyareconnectedtoUSB2.0hostadapter
or USB 2.0 hubs.
SystemRequirements
PC:
•
•
Pentium-class computer with an available PCI slot
Windows 2000 SP4 or later/XP SP1 or later/
Server 2003/Vista
Mac:
•
Power Mac G3 (blue & white) or later with an
available PCI slot
•
Mac OS 10.2.8 or later
04-0444A
Download from Www.Somanuals.com. All Manuals Search And Download.
1
USBPin-outHeader
The USB pin-out header consists of 4 pins and allows for
1 USB connection.
Important: The internal USB port and the USB Pin-out
Header can not be used at the same time. Do not connect
devices to both ports at the same time.
Black
Green
GND
White
DATA +
Red
DATA -
VCC/+ 5VDC
Figure 2. USB Pin-out Header
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer's case for a few
seconds. Avoid any contact with internal parts and
handle card only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplugthepowercordandremoveyourcomputer's
cover.
3. Remove the slot bracket from an available PCI slot.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Carefully align the card to the selected PCI slot,
push the board down firmly, but gently, until it is
well seated.
5. Replace the slot bracket's holding screw to secure
the card.
6. Replacethecomputercoverandreconnectthepower
cord.
Windows Driver Installation
The Hi-Speed USB 5-Port PCI has three built-in USB hosts.
Two hosts handle USB 1.1 devices and the third host
handles USB 2.0 devices. USB 1.1 and USB 2.0 devices are
automatically routed to the correct USB hosts.
WindowsDriverInstallation
Windows 2000 Service Pack 4 or later, Windows XP
Service Pack 1 or later, Windows 2003 Server, and Vista
have built-in driver support for this controller. Just
install the board and Windows will automatically detect
and install the correct drivers for it. No additional driver
is necessary.
ToVerifyWindowsInstallation
Right click My Computer. Click Manage, then click
Device Manager.
Under Universal Serial Bus controllers:
- NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- Standard Enhanced PCI to USB Host Controller
- USB Root Hub (USB 2.0 Root Hub in Win2K)
- USB Root Hub
- USB Root Hub
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Mac OS Driver Installation
Mac OS has built-in driver support for this controller.
Just install the board and Mac OS will automatically
detect and install the correct drivers for it. No additional
driver is necessary.
To Verify Mac OS Driver Installation
Mac OS X (v10.2.8)
The only way to verify the board works is actually
connecting devices to the USB ports.
Mac OS X (v10.3.0) or later
Check System Profiler to verify successfull installation.
Click Go, then Utilities. Double click on System Profiler
Under USB
- USB High-Speed Bus
- USB Bus
- USB Bus
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Blank Page
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS?
SIIG’s Online Support has answers!
Our online support database is updated daily with new drivers
and solutions. Answers to your questions could be just a few clicks
away. Youcanalsosubmitquestionsonlineandoneofourtechnical
support analysts will promptly respond.
Thisproductcomeswithalifetimemanufacturerwarranty. Pleasesee
SIIGwebsiteformorewarrantydetails. Ifyoushouldhappentohave
any problems with this product, follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
request to SIIG RMA. If the product is determined to be
defective,anRMAnumberwillbeissued. SIIGRMAdepartment
can also be reached at (510)413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538
RMA#:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
Networking,SoundCards,andotheraccessories. SIIGisthepremier
one-stop source of upgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
foundincomputerretailstores,mailordercatalogs,ande-commerce
sitesintheAmericasandtheUK,aswellasthroughmajordistributors,
system integrators, and VARs.
PRODUCT NAME
Hi-Speed USB 5-Port PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
Hi-SpeedUSB 5-PortPCIisatrademarkofSIIG,Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Mac and Mac OS are registered trademarks of
AppleCorporation. PentiumisaregisteredtrademarkofIntelCorporation. Othernamesusedin
publicationareforidentificationonlyandmaybetrademarksoftheirrespectivecompanies.
December, 2006
Copyright ©2006 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|